Miele T 1036 VENT ED DRYER - OPERATING Operating instructions

Operations Manual
for the T 1526
Vented Dryer
It is essential to read these
operating instructions before
installing or using the machine to avoid
the risk of accident, or damage
to the machine.
ö
M.-Nr. 04 979 250
Contents
Contents
Guide to the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Your contribution to the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Loading and unloading the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Program selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To select a program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To change a program during drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correct procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
After the program has finished. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
11
11
11
11
Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning the lint filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
After-sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grounding and Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exhaust venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
20
21
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2
Guide to the machine
Guide to the machine
1
2
3
4
5
Supply cable with plug
Control panel
Drum door
Exhaust connection (left or rear)
Four height-adjustable legs
3
Guide to the machine
Pushbuttons
Indicator lamps
– Door
This button is used to open the door
(does not stay pushed in).
– PROGRAM SEQUENCE
The program sequence indicator
lamps show the current state of the
drying program.
– j ON / k OFF
When the machine is turned on, the
“On” indicator will light up if the door is
closed. If the door is open, the drum
light will be on.
– Buzzer
Allows the buzzer to sound as the
drum rotates during the anti-crease
cycle.
– Low temp.
Lower drying temperatures for delicate fabrics, e.g. acrylics, nylon.
– Start
Starts the selected program (does
not stay pushed in).
– DRYING STAGE REACHED
These indicator lamps show which
drying stage the program has
reached. For program stages “Normal” and “Extra dry” the indicator
lamp remains at the “Normal” position.
PROGRAM SETTING-SELECTOR
Set the desired program by turning the
knob either clockwise or counterclockwise.
– COTTONS
– PERMANENT PRESS
– TIMED DRYING
Items can be either dried for 20
minutes (incl. a cooling-down phase)
or cool air fluffed for 15 minutes.
4
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING - To reduce the risk of fire,
electric shock, or injury to persons
when using your appliance, follow
basic precautions, including the following:
1. For your own safety and for the protection of your machine read these
operating instructions carefully before using your dryer for the first time.
2. Remember to remove the door when
disposing of an old machine to prevent children from accidently locking
themselves in.
3. Do not install or store this appliance
where it will be exposed to the
weather.
4. Do not install your dryer in rooms
where freezing temperatures may
occur. The reliability of the electronic
control system may be impaired.
5. This machine should only be used for
drying the following fabrics:
– Items which can be machine dried
as specified by the laundry care
label.
– Items which have been washed in
water.
7. Fabric softener sheets are not recommended for use in the tumble dryer.
Best results occur when a liquid softener is used in the washing machine.
8. Clean the lint filter before and after
each load.
9. Do not dry articles that have been
previously cleaned, washed, soaked
in, or spotted with gasoline, drycleaning solvents, or other flammable or explosive substances.
They give off vapors that could ignite
or explode.
10.Do not allow children to play on or in
the appliance. Close supervision is
necessary when the appliance is
used near children.
11.Always close the door after use to
prevent children from leaning on the
door and causing the dryer to tilt.
12.Keep the area around the air intake
(toekick) and adjacent surrounding
areas free from lint, dust and dirt.
6. The following fabrics pose a fire hazard. Do not use a dryer to dry these
items.
– Items which contain foam rubber,
rubber or rubberlike components.
– Items which have been treated with
flammable cleaning agents, such as
gasoline or dry-cleaning solvents.
– Items containing, hairspray, nail polish remover or similar substances.
5
IMPORTANT SAFETY INSTRUCTIONS
13.The interior of the machine and exhaust duct should be cleaned periodically by qualified personnel.
14.Do not reach into the dryer if the
drum is moving.
15.Do not tamper with the controls.
16.Do not repair or replace any part of
the appliance or attempt any servicing unless specifically recommended in this Operations Manual.
Repairs to electrical appliances
should only be peroformed by qualified personnel.
Incorrectly repaired machines may
pose a considerable risk to the user.
17 Lint is principally the result of friction
caused by items being worn and
washed. Machine drying causes insignificant amounts of lint to form.
It has been established by research
institutes, that dryers have no
detrimental effects on the lifetime of
fabrics.
18.Do not place items exposed to oils
in your dryer. Items contaminated
with oils may contribute to
a chemical reaction that could
cause the laundry to catch fire.
SAVE THESE INSTRUCTIONS
For grounding and electrical connection instructions, refer to the electrical connection section.
This dryer is only intended for
residential use!
6
Your contribution to the environment
Your contribution to the environment
Disposal of the packing material.
The packaging is mostly manufactured
from the following recycled or reuseable materials:
– corrugated paper/cardboard
Disposal of your old machine.
Old machines contain materials which
can be recycled. Please contact your
recycling center and render the machine inoperative as per the “Important
Safety Instructions” before disposing of
the appliance.
– polystyrene - CFC-free
– polyethylene foil (transparent)
– untreated wood
– fiber board
Please check local environmental regulations before disposing of packing materials and discarding the appliance.
7
Loading and unloading the machine
Loading and unloading the machine
WARNING - To reduce the risk of
fire, electric shock, or injury to persons, read the IMPORTANT SAFETY
INSTRUCTIONS before operating
this appliance.
Load the laundry loosely into the
drum.
Comforter covers and pillowcases
should be fastened before drying in
order to prevent small items from rolling inside of them.
If the wash is not removed at the end
of the drying program, the machine
will automatically enter an anticrease cycle for 60 minutes. This
causes the drum to rotate at short intervals in order to reduce the formation of creases.
Once the laundry has been
removed, check that the drum is
empty. Any items left in the drum
could be damaged through overdrying during the next program.
Clean the lint filter after each drying
cycle to prevent excessive energy
consumption, longer program times
and the risk of fire.
The door should always be closed
when not in use.
Important: Check that the laundry
cannot be caught by the closing
door as this may cause damage to
the fabric.
8
Notes on laundry care
Notes on laundry care
Before drying, check the instructions
on the fabric care label.
The following fabrics should not be
dried in a tumble dryer:
– Woolens and wool blends
These fabrics tend to matt and shrink.
– Items filled with down
The fine fabric interior tends to shrink,
depending on the quality of the item
involved.
– Pure linen
These items should only be machinedried if specified as suitable by the
manufacturer on the textile care label.
The surface of the fabric may otherwise tend to become “rough”.
– Rubber or rubber backed items
They may melt or ignite.
Miele dryers have been designed to
dry laundry free of static cling, without
the use of dryer softener sheets or similar products. The dryer continuously
monitors the moisture content of the
laundry, and automatically shuts off the
heat when the selected degree of dryness is reached. Through the use of a
cooling cycle, (where the machine
operates without heat), cool, static free
laundry results. Dryer softener sheets
perform the same function by depositing a chemical residue on both the
clothes and the interior of the dryer.
Over time, this coating may lead to performance reductions in the dryer.
If fabric softening is desired, it is more
convenient, economical and beneficial
to the clothing if a liquid softener is
automatically dispensed while the
clothes are in the washing machine.
Please see the washing machine operating instructions for directions on how
to automatically dispense a liquid softener.
Notes:
Knitted fabrics and flannel sheets tend
to shrink when washed for the first time
and also when dried. They should not
be overdried.
Starched laundry can also be dried in
the tumble dryer.
Permanent press items should be
briefly spun in the washing machine before drying. Items which are prone to
creasing should not be dried using the
“PERMANENT PRESS- Normal +” or
“COTTONS”- programs.
Drip-dry shirts made of pure cotton
may tend to wrinkle, depending on the
quality of their finish. These items
should be dried using a “Hand iron”
program.
Permanent press fabrics tend to crease
more as the size of the load increases.
This is also true of very delicate fabrics.
These loads should be reduced to 3
lbs or to 2 lbs, if necessary.
Do not dry new dark-colored fabrics
together with light-colored items as
they may discolor.
9
Program selection
Program selection
Functional description
An electronic sensor system monitors
the moisture content of the laundry.
Once the required degree of dryness is
reached, cold air enters the drum to
cool the laundry.
The drying program is then terminated.
Function of the pushbuttons
– Low temp.
When selected the machine uses
lower drying temperatures for delicate fabrics, (e.g. acrylics, nylon).
– Start
Starts the selected program.
“PROGRAM SEQUENCE”
indicators
The program sequence indicator lamps
show the current status of the drying
program.
“DRYING STAGE REACHED”
indicators
This indicator shows which drying
stage the program has reached.
“PROGRAM SETTING” selector
– Door
This button is used to open the door.
– ON/OFF
When the machine is turned on, the
“On” indicator lamp lights if the door is
closed. When the door is open, the
drum is illuminated.
– Buzzer
When depressed, the buzzer will
sound as the drum rotates during the
anticrease cycle.
10
There is a range of settings for both
"Cottons" and "Permanent Press".
In addition, items can be either dried
for 20 minutes (incl. a cooling-cycle
lasting 8 mins.) or fluffed in cool air for
15 minutes.
Program selection
To select a program
Press the "On/Off" button.
To change a program during
drying
Set the program selector to the
desired program.
The new program will start from the beginning.
The tables on the following pages list
the range of applications for the different programs.
Set the desired program by turning
the program selector either clockwise or counterclockwise.
Press the "Start" button.
The program status will be stored for
30 minutes in the event of a power
failure.
The program is canceled if:
– There is a power failure lasting more
than 30 minutes.
– The door is opened after the machine has entered the "Cooling
down" or "Anti-crease" stage.
Correct procedure
1 Press the "On/Off" button.
2 Press the "Door" button.
3 Open the door and load the machine.
4 Close the door with a firm swing - do
not push it shut.
5 If drying delicate fabrics, press the
"Low temp." button.
6 Select the "Buzzer" if so desired.
7 Select a program.
8 Press the "Start" button.
After the program has finished
1 Set the program selector to "Finish".
2 Remove the laundry.
3 Clean the lint filter.
4 Turn off the machine.
11
Programs
Programs
Drying stage
Type of laundry/fabric
Max. load
Special instructions
Multi-layer fabrics, mixed
loads of cotton fabrics,
e.g.jeans, towels,
sweatsuits.
Uniform loads of cotton
fabrics e.g. flannel items,
underwear, socks.
Knitted cotton fabrics
susceptible to shrinkage,
e.g. jersey wear or
lightweight cotton fabrics.
Cotton or linen fabrics, to
be left damp for easier
ironing.
15 lbs
The “Extra dry” program
should not be selected for
jersey wear items or items
that may shrink.
If items are still damp,
select the “Extra dry”
program.
If items are still damp,
select the “Normal“
program.
COTTONS
Extra dry
Normal
Normal-
Hand iron r
Hand iron rr
Machine iron
12
Cotton or linen fabrics,
including starched laundry,
to be ironed on the rotary
iron, (B865E).
15 lbs
15 lbs
15 lbs
15 lbs
Moisture can be increased
or decreased by using
“Hand iron rr” or “Hand
iron r” respectively.
The laundry can be loosely
rolled to prevent it from
drying out until it can be
ironed.
Programs
Drying stage
Type of laundry/fabric
Max. load
Special instructions
Permanent press items
made of synthetic or
blended fabrics, e.g.
pullovers, dresses, pants,
etc., which are not dried
adequately in the “Normal”
program.
Permanent press shirts,
table cloths, bedding etc.
made of blended woven or
knitted fabrics, e.g.
cotton/synthetic.
Permanent press shirts,
table cloths, pillowcases
etc. cotton/synthetics,
which are to be pressed.
7 lbs
With blended fabrics
consisting of wool and
synthetics, consult the
manufacturer’s
instructions, as the wool
component may cause the
fabric to matt and shrink.
Individual items, e.g.
comforters, or very small
loads.
Items which you want to
"fluff".
-
PERMANENT PRESS
Normal +
Normal
Hand iron
7 lbs
7 lbs
TIMED DRYING
warm
cool air
13 lbs
This cycle will run for the
full 20 minutes, even if the
clothes are dry sooner.
-
13
Cleaning and care
Cleaning and care
Cleaning the lint filter
The lint is collected by the lint filter in
the door.
Clean the filter after every program.
Cleaning the dryer
Before cleaning the tumble dryer,
disconnect the machine from the
power supply.
The dryer can be cleaned using
soapy water or a mild non-abrasive
detergent (not scouring powder)
and dried with a soft cloth.
The drum may be cleaned using a
suitable stainless steel cleaner following the manufacturer’s instructions.
Do not hose down the machine or
use abrasive cleaners.
Grip the filter by the recessed
handle and pull up to remove.
Any lint remaining in the hollow part
of the door can be removed through
the gap at the bottom.
The lint filter can be rinsed with water if
necessary.
Dry the lint filter before putting it
back in place.
14
Problem solving guide
Problem solving guide
Electrical appliances should only be repaired by qualified personnel. Incorrectly repaired machines may put the user at risk. There are, however, minor
problems which can be corrected without contacting the Service Department.
What to do if, . . . ?
Possible Cause . . .
Remedy . . .
. . . the tumble dryer fails to
start when turned on?
Check whether the "On"
indicator is lit. If so, failure to
start may be due to an incorrect
program selection procedure.
If the "On" indicator lamp does
not illuminate, check that:
. . . the laundry is not sufficiently dry?
The load consisted of dissimilar
items (size and fabrics).
Small loads or individual items
may cause the program to
terminate prematurely.
The lint filter is clogged.
The laundry was not spun in the
washer for a sufficient time.
Repeat the program selection
procedure in the correct
sequence, as outlined in the
“Program Selection” chapter.
– The "ON/OFF" button is
depressed.
– The door is properly closed.
– The machine is plugged in
and the fuse or circuit breaker
has not tripped.
Select a longer drying program.
. . . the drying times are too
long?
. . . the "anti-crease" indicator
lamp starts flashing?
Small loads can be time-dried.
Clean the lint filter in the door.
Make sure that the laundry is
thoroughly spun before drying.
– Turn the program selector
to "finish".
– Turn the machine off and
then on again.
– Select a program.
– Press the "Start" button.
If the indicator lamp starts
flashing again, this indicates a
fault in the machine.
Please contact the Miele
Service Dept.
15
Problem solving guide
What to do if, . . . ?
. . . the drum door opens during the drying cycle?
. . . the interior drum light fails
to function?
. . . you have to open the door
in the event of a power
failure?
16
Possible Cause . . .
Remedy . . .
Before restarting the program,
The machine has overheated.
proceed as follows:
The safety thermostat opened
– Release the ON/OFF button.
the drum door and caused the
– Clean the affected part of the
machine to turn off
machine.
automatically.
– Turn the machine on again.
Possible reasons for
– Reselect a program.
overheating:
– Press the “Start” button.
– The lint filter in the door is
clogged.
If the drum door opens again,
– The vent duct is blocked.
the Miele Service Dept. should
– The vent aperture (e.g. louvred be contacted.
window vent, wall vent) is
blocked.
It only lights up when the
machine is turned on. The bulb
may be burnt out.
See next page.
See next page.
Problem solving guide
The interior drum light fails to function: The bulb may be burnt out.
To open the door in the event of a
power failure
Replace it as follows:
Turn off the machine or disconnect
it from the power supply.
Open the door.
Pull forward on the un-hinged side of
the door.
Unscrew the plastic blub cover located inside the drum and above the
door (see illustration).
The light bulb must not exceed the
maximum wattage quoted on the
data plate.
Replace the bulb and the plastic
cover.
The cover must be correctly installed
and tightened, otherwise moisture may
seep in and cause the socket to corrode.
This is a temperature-resistant bulb
and should only be ordered from the
Miele Service Dept.
17
After-sales service
After-sales service
In the event of problems which you cannot solve, please contact:
– The nearest Miele Service Department (see back cover for phone numbers).
When contacting the Service Department, please have the Model and Serial numbers of your appliance available. Both of these can be found on the
right side of the opened door.
Sample:
18
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Grounding and Electrical connection
Grounding instructions
This appliance must be grounded.
In the event of a malfunction, grounding will reduce the risk of electric shock
by providing a path of least resistance
for the electric current. This appliance
is equipped with a cord having an
equipment grounding conductor and a
grounding plug. The plug must be
plugged into an appropriate outlet that
is properly installed and grounded in
accordance with all local codes and ordinances.
Warning
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or
serviceman if you are in doubt as to
whether the appliance is properly
grounded.
Do not modify the plug provided
with the appliance; if it will not fit the
outlet, have the proper outlet installed by a qualified electrician.
Electrical connection
This installation should be done by an
experienced and qualified person, in
most cases a licensed electrician, in accordance with local codes and regulations.
The dryer is supplied with a 5 ft long,
12/4 AWG cord and a NEMA 14-30 P plug.
It should be connected to a 120/240 V
(208 V), 15 A, 60 Hz AC power supply.
A 3 pole-4 wire grounding receptacle is
needed. (NEMA type 14-30 R).
“EASY INSTALLATION KIT”
If you do not have a dedicated 15 Amp
line for this appliance, but you have the
standard 3 or 4 wire, 240 V - 30 Amp
outlet, you can use the “Easy Installation Kit”, which allows you to use that
line to connect this appliance.
For more information on the electrical
connection and the “Easy Installation
Kit” please contact
– the nearest Miele Service Department.
19
INSTALLATION INSTRUCTIONS
Installation
Where to install the machine
The space required by the vent
duct should be taken into consideration when calculating the distance
between the machine and a wall or
other appliance.
The tumble dryer can also be placed
on top of a Miele washing machine for
a stacked installation.
The machine should be perfectly level
to ensure safe and proper operation.
Minor discrepancies will not, however,
have an adverse effect on operation.
The machine can be leveled by turning the legs clockwise or counterclockwise as necessary.
20
An appropriate stacking kit is required
and can be obtained from your Miele
dealer, or the Miele Parts Dept.
INSTALLATION INSTRUCTIONS
Exhaust venting
The moist air from the dryer must be
vented to the outside.
Installing the connector on the left
side of the machine
Remove the cap covering the exhaust part as follows:
The appliance should not be vented
into a chimney, a wall, a ceiling, or
any concealed spaces of the building.
When installing, try to avoid:
- very long venting systems
- too many bends or angles
- tight corners
otherwise . . .
. . . the drying results will be affected,
. . . drying will take longer and use more
energy.
Materials suitable for venting:
– rigid metal pipe
– flexible metal pipe
To prevent the risk of fire, do not
use vinyl or foil ducting for venting.
– Insert a thin screwdriver into the slot
by the retaining hook. Press the hook
gently upwards.
At the same time turn the cap
counterclockwise.
Install the venting in such a way that
the expelled air cannot be drawn
back into the machine.
Do not vent the dryer into a flue used
by gas or fuel boilers or heaters.
A vent connector is included with the
machine. It should be pressed into the
vent outlet and will simplify the connection of the exhaust pipe.
Before installation, disconnect the
tumble dryer from the electrical supply (unplug from the wall socket, or
turn off the circuit breaker.
Installation at the rear
The machine comes supplied with
the connector installed on the rear
exhaust port.
In the same way remove the vent
socket from the rear exhaust port.
Secure into the side port by pressing
it in and turning it clockwise.
Seal the rear exhaust port using the
cap.
21
INSTALLATION INSTRUCTIONS
The shorter the exhaust ductwork, the
more efficient the dryer will run. Expelled air is slowed down in the ducts
due to friction against the inner walls.
The shorter and smoother the inner
walls are, the less friction will be created.
An elbow or bend creates more friction
than a straight duct. An Additional Duct
Length Factor must therefore be added
for each elbow or bend used (see
Table I). This factor expresses the resistance of the bend in terms of a
length of straight duct.
The Additional Duct Length Factor is
then added to the actual duct length to
give the Effective Duct Length.
A larger diameter duct also helps to reduce friction. Duct diameter should
therefore be increased for longer duct
runs.
To calculate the Effective Duct Length.
Measure the actual straight duct
length needed.
Establish the number of elbows or
bends necessary, noting the type of
bend, angle and radius involved.
(see Table I).
Add the Addiditional Duct Length as
specified in Table I to the actual duct
length to get the Effective Duct
Length.
The necessary duct diameter can
then be found in Table II.
Note:
Drying times and energy consumption
remain unaltered for 4’’ duct up to a
total length of 26’.
Longer ducts may lead to slight increases in drying times and energy
consumption but will not impair the
function of the machine as long as the
necessary duct diameter is used (see
Table II).
Tabel I
Type of bend
Flexible metal duct
Smooth metal duct
Elbow 90° sharp; no radius
Concertina bend
Wall vent kit with louvres, or window vent kit
Wall vent kit with flap, or window vent kit
Exhaust connection, left side
22
Angle
Radius in inches
90°
45°
90°
90°
90°
up to 16’’
up to 16’’
4’’
8’’
Additional duct
length in inches
20’’
12’’
14’’
90’’
28’’
142’’
99’’
193’’
INSTALLATION INSTRUCTIONS
Table II
Effective duct
length (yds)
0 - 13
12 - 25
25 - 45
Example:
Internal diameter or
edge length (inches)
4’’
5’’
6’’
Flexible metal ducting has been used
for the following example.
Exhaust connection, left . . . . . . . . 193’’
Length (L) . . . . . . . . . . . . . . . . . . . . 46’’
Lower radius (R=4’’) . . . . . . . . . . . . 20’’
Height (H) . . . . . . . . . . . . . . . . . . . . 46’’
Upper radius (R=2’’) . . . . . . . . . . . . 20’’
Wall pipe with louvred vent . . . . . . 142’’
Effective duct length . . . . . . . . . . . 467’’
. . . . . . . . . . . . . . . . . . 467’’ = 12.9 yds
Result:
A duct diameter of 4’’ is adequate
since the effective length is less than
13 yd as specified in Table II.
23
INSTALLATION INSTRUCTIONS
Moist air can be ducted outside by a wall
vent or window vent, both which are available from the Miele Parts Department.
Window vent kit
Wall vent kit
1. Louvred wall vent frame
2. Wall vent duct
3. Adapter
4. Louvred wall vent
5. Flap
6. Screw
7. Wall anchor
1. Louvred window vent frame
4. Louvred window vent
5. Flap
8. Clips (4 pcs.)
9. Raised head screws (4 pcs.)
The window vent kit is installed into in a plexiglass pane. If using an existing glass pane, cut a
hole with a diameter of 4 15/16’’.
A flexible foam gasket must be used if the
tumble dryer is directly connected to the wall
vent.
Dryer-top view:
1. Window vent kit
2. Adapter for vent duct
1. Wall pipe
2. Flexible foam-gasket
24
INSTALLATION INSTRUCTIONS
Fig. 1
Ducting (side view) with flexible vent hose to an
exhaust flue.
Fig. 2
Height of vent outlet for washer/dryer stack.
1. Wall vent duct
A. Flexible ducting
2. Adapter
3. Flue insulated against dampness
25
Technical data
Technical data
Height. . . . . . . . . . . . . . . . . . . . . . . . . .
33 1/2’’
(adjustable between 33 1/4’’-33 7/8’’)
Width . . . . . . . . . . . . . . . . . . . . . . . . . .
23 1/2"
Depth (incl. distance from wall) . . . . . .
27 3/8’’
Weight . . . . . . . . . . . . . . . . . . . . . . . . .
126 lbs
Drum volume . . . . . . . . . . . . . . . . . . . .
4.4 ft3
Capacity . . . . . . . . . . . . . . . . . . . . . . . .
15 lbs
Rated load . . . . . . . . . . . . . . . . . . . . . .
see data plate
Fuse rating . . . . . . . . . . . . . . . . . . . . . .
see data plate
26
Consumption data
Consumption data
load
Final spin speed in washer*
Electrical
consumption
lbs
rpm
kwh
Drying time
incl.
cooling down
time
mins
Extra dry
15
1200
1400
1600
3.65
3.50
3.20
92
89
81
Normal
15
1200
1400
1600
3.15
3.00
2.70
82
79
71
Normal-
15
800 (70 % residual moisture)
1200
1400
1600
3.85
3.00
2.85
2.55
98
79
75
68
Hand iron rr
15
800 (70 % residual moisture)
1200
1400
1600
3.10
2.25
2.10
1.80
82
63
59
52
Machine iron
15
1200
1400
1600
1.80
1.65
1.35
52
48
41
Cottons
Permanent Press
Normal +
7
1000
1.49
44
Normal
7
1000 (50 % residual moisture)
1.40
41
Hand iron
7
1000
1.20
37
The specified program running times and electrical consumption values were established under standard conditions (EN 61121/A11).
Different types of fabrics, load size and residual moisture after spinning may effect the specified
values.
*These values apply if the laundry is spun in a Miele washing machine before drying.
27
All rights reserved/005
3101
These instructions are printed on 100% unbleached, recycled paper are completely Biodegradable.