White-Westinghouse WM40T Specifications

DORLEN Products Inc.
MASTERCATALOG
r Alerts....
eries Wate
S
"
R
"V
w
e
N
estrooms!
for use in R
d
e
n
ig
s
e
D
PREVENTDOWNTIME,DAMAGE
ANDBUSINESSDISRUPTION!
R
R
SYSTEMSINSTALLEDINOVER21,000SITESACROSSTHEU.S.!
R
Detect small leaks ... (condensate water overflow, chiller water leaks,
plumbing line cracks, heating/cooling piping leaks, outside seepage,
etc.)... before damage and downtime occur!
R
- is a water leak detection system used in
suspended ceilings. This system provides
early warning of water drips and leaks
before damage occurs to the area below.
WA
TER ALERT
WA
TER ALERT
R
R
- spot detectors are used in a wide
range of applications to prevent
damage and downtime from water
leaks and spills. Six models available.
- is a unique accessory that expands
the capability of the WATER ALERT.
Guards against undetected water
leakage. Used in large areas or
perimeter monitoring.
��� ������ ��������
���� �� ��� ���
1
1
NEW! "VR" SERIES Water AlertsVandal Resistant - For use in Restrooms.
See Page 9 for details!
All products in this catalog are available
DIRECT from Dorlen Products Inc. This
catalog is also available for download in
pdf format at www.wateralert.com.
Engineering specifications are also available for download at our web site. For help
in system design, layouts and quotations,
please contact Dorlen's technical dept. at
1-414-282-4840 or dorlen@execpc.com.
Thank you!
Table of contents
Systems Description............................................................................................................................................1
Notes and Table of Contents...............................................................................................................................2
Water Alert "SS" Series Introduction...................................................................................................................3
Water Alert Principle of Operation- "SS" Series...................................................................................................4
Water Alert Self Contained Models: SS, SS-1 and SS-2......................................................................................5
Water Alert Wired Models: SS-4, SS-5 and SS-2100...........................................................................................6
NEW! Water Alert"VR" Series Introduction, Models: VR-4 and VR-2100 ......................................................................7
Water Alert "VR" Series Principle of Operation.....................................................................................................8
Sensor Cable Introduction ....................................................................................................................................9
Sensor Cable Principle of Operation, Models: SC-12, SC-24 and SC-36...........................................................10
Series 2100 Introduction, General Description....................................................................................................11-12
Series 2100 Monitor Models: SM-6(T) / SM-12(T)...............................................................................................13
Series 2100 Monitor Model: WM-6(T) / WM-12(T)...............................................................................................14
Series 2100 Monitor Model: WM-20(T) / WM-40(T).............................................................................................15
Series 2100 Monitor Model: SM-12(AT)...............................................................................................................16
Ceiling Guard Introduction, Principle of Operation..............................................................................................17-18
Ceiling Guard Series 2000, Models: CGM-6(T), CGM-12(T), CGM-20()T) and CGM-40(T).................................19-24
NEW! Accessories (Power Supplies, Power Relays, Auto-Dialer, Valves, Wire)............................................................25-28
Warranty...............................................................................................................................................................29
How to Order........................................................................................................................................................30
2
�
WATER LEAK DETECTION SYSTEMS
"SS" Models
-6 Models with optional accessories to meet
your specific requirements.
-Used in a wide range of applications, from
computer rooms to mechanical rooms...
anywhere undetected leakage can occur.
-All units tested 3 times during manufacture,
and come with a 5 Year Limited
Warranty. Made in the USA.
-Simple installation using instructions furnished with all equipment, normally done by
maintenance personnel. Typical spacing is
one Water Alert for every 300-400 sq. ft.
From the boiler room...
-Water Alert will NOT activate due to high
humidity and is not affected if submerged in
water for short periods.
-Installed in over 21,000 sites across the U.S.,
Water Alert has proven to be the most rugged,
simplest to install and longest lasting water
detector available today.
to the computer room...
WATER ALERT will
provide early warning
of water leakage!
AVOID THIS SCENE!
3
�
WATER LEAK DETECTION SYSTEMS "SS" Models
WHEN WATER FILM FORMS A BRIDGE BETWEEN
SENSORS (A & A), WATER ALERT BECOMES
ACTIVATED!
PRINCIPLE OF OPERATION AND
CONSTRUCTION "SS" MODELS.
5-3/4"
*
Water Alert® is activated by liquid bridging the adjustable sensors (A & A). The unit can detect water film
from zero height, (sensors turned out to make contact
with the floor), to 1/8" height, (sensors turned all the
way in). The units are factory adjusted to activate with
1/32" water film height which is satisfactory for most
applications. The pads B1 and B2 provide a gap between the case and the surface to admit water under
the unit for detection. If desired, the self adhesive pad
feature may be used by peeling off the thin protective
layer from each pad. The self-adhesive pads along with
the inherent low convex Water Alert profile minimizes
the chance of the unit being inadvertently moved about
after being located. Replacement pads are available
(no charge) by request from Dorlen Products.
*
WATER
FILM
1-1/4"
A
B1
A
B2
Floor or Horizontal surface
A
Water leakage . . . including solutions of water and
ethylene glycol (used in many computer room air
conditioning systems).
A
The adjustable gold plated sensing
probes, located on the under side of
the water alert.
CONSTRUCTION
Epoxy encapsulated sensing/control circuit avoids
problems of dirt, fungus or humidity affecting
circuit operation or increase of
battery drain with time . . .
Circuitry is impervious
to water immersion.
85db SS-2100, 100db all other
models (at 3 feet) Piezo electric
buzzer protected against
short term immersion.
Buzzer simply replaceable
if damaged by long term submersion.
TER ALERT
WA
1/8 " thick, high-impact polystyrene
dome-shaped housing for strength
and ruggedness.
9vdc operating voltage for
a safe and simple
Installation. (no
conduit required)
Compact Design: 5-3/4" diameter,
1-1/4" high, approximately 1 lb.
shipping weight.
Specifications for all products
are available for download at
www.wateralert.com
2-9-93
Nickel-gold plated adjustable (1/64" to
1/8") sensing probes corrosion resistant.
Nylon pellet assures positive connection
from probes to sensing circuit.
4
Note: All "SS" Water Alert models are
the same physical size. The difference
between models is the result of internal
circuitry differences.
�
WATER LEAK DETECTION SYSTEMS "SS" Models
MODEL SS -
(Model XSS when using
Standard Water Alert detector provides audible alarm
when activated.
Powering options - 9v Alkaline Battery (Qty.1)
- PS-3 Power Supply (Pg. 25)
- Voltage Module (Pg. 26)
optional Sensor Cable)
Audible alarm - 100db @ 3 feet
- 3 day alarm duration
(Battery Operation)
Power draw - 25ma @ 9vdc (activated)
- Used in applications where only a local audible alarm is desired.
MODEL SS-1 -
(Model XSS-1 when using
Water Alert detector provides local and remote
alarms when activated.
optional Sensor Cable)
Powering options - 9v Alkaline Battery (Qty.2)
- PS-3 Power Supply (Pg. 25)
- Voltage Module (Pg. 26)
Audible alarm - 85db @ 3 feet
- 1.5 day alarm duration
(Battery Operation)
Remote alarm - 85db @3 feet w/ silence switch
- 9/16” Red lamp
- Wall Mounted 6”x3”x2” enclosure
- 50' Cable included
- Used in applications requiring a single detector and remote alarm. Often used in
noisy or unattended areas.
Power draw - 40ma @ 9vdc (activated)
Alert detector provides audible alarm when
MODEL SS-2 - Water
activated.
(Model XSS-2 when using
optional Sensor Cable)
Powering options - 9v Alkaline Battery (Qty.2)
- PS-3 Power Supply (Pg. 25)
- Voltage Module (Pg. 26)
Audible alarm - 100db @ 3 feet
- 10 day alarm duration
(Battery Operation)
Power draw - 25ma @ 9vdc (activated)
- Used in applications where only a local audible alarm is desired and an extended alarm duration is required. (Battery operation- 10 day).
5
�
WATER LEAK DETECTION SYSTEMS "SS" Models
MODEL SS-4 (Model XSS-4 when using
optional Sensor Cable)
Water Alert detector - No audible alarm...Provides
isolated dry relay contacts (DPDT) which transfer and
hold when activated. Self-resets.
Powering options - 9v Alkaline Battery (Qty.2)
- PS-3 Power Supply (Pg. 25)
- Voltage Module (Pg. 26)
Audible alarm - None
Relay contacts - DPDT ( 2- Form C)
- 28 VDC@ 1 amp. MAX.
(For high power applications
see p.26 model PR-WM)
- Used in applications where tie-in to an existing alarm panel is desired (Building
Management System, etc.) and no audible alarm is necessary. Also ideal for extremely
harsh environments and can control valves, pumps and other electrical equipment.
MODEL SS-5 (Model XSS-5 when using
optional Sensor Cable)
Water Alert detector provides audible alarm and
isolated dry relay contacts (DPDT) which transfer
and hold when activated. Self-resets.
Power draw - 1ma @ 9vdc (activated)
Powering options - 9v Alkaline Battery (Qty.2)
- PS-3 Power Supply (Pg. 25)
- Voltage Module (Pg. 26)
Audible alarm - 100db @ 3 feet
- 10 day alarm duration
(Battery operation)
Relay contacts - DPDT ( 2- Form C)
- 28 VDC @1 amp. MAX.
(For high power applications
see p.26 model PR-WM)
- Used in applications where tie-in to an existing alarm panel is desired (Building
Management System, etc.). Can also be used to control valves, pumps and other
electrical equipment.
MODEL SS-2100 -
Power draw - 25ma @ 9vdc (activated)
Water Alert detector used to tie-into all
Dorlen’ Series 2100 Monitors
(Model XSS-2100 when using
Powering options - Powered from Monitor (Pg. 11)
optional Sensor Cable)
Audible alarm - 85db @ 3 feet
Relay contacts -None
Power draw - 20ma @ 9vdc (activated)
- Used in applications where a Dorlen Series 2100 Monitor / Power Supply is
desired.
6
R
A UNIQUE ACCESSORY
EXPANDS THE CAPABILITY OF
"SS" SERIES WATER ALERT...
For large areas or
perimeter monitoring
the Water Alert /
Sensor Cable system
is your best defense
against downtime due to water
leaks and floods!
����
�����
�� �
�����
����
��
�����
�
��
��
����� ���
���
�
By using Water Alerts in combination
with Sensor Cable the user can purchase
a system specific to their needs, from a simple
local audible alarm to a large monitoring system.
FEATURES:
Sensors every 3 feet for practical and effective coverage
3 Standard lengths to match your requirements
Local audible alarm - eliminates need for maps
Adaptable to any "SS" SERIES Water Alert Detector (add “X” prefix
to model #)
Gold plated sensors for max. corrosion resistance
Cable quickly dries providing no-fuss repeated use
Up to 72 ft. of Sensor Cable per Water Alert
Ultra-flexible, low memory cable
No sensitivity adjustment
No false activations
Simple installation
5 year warranty
Water Alert /
Sensor Cable
in mechanical
Room
7
R
APPLICATION AREAS
-BELOW ACCESS FLOORING
(Computer rooms, Data centers)
-RECORDS STORAGE, ARCHIVE AREAS
-BELOW GRATED FLOORING
(Clean rooms, Semiconductor Mfg.)
-MECHANICAL / ELECTRICAL ROOMS
-VALUABLE MATERIAL STORAGE AREAS
-UNATTENDED & DIFFICULT ACCESS AREAS
DATA CABLE RACEWAYS/TRAYS
PRINCIPLE OF OPERATION AND CONSTRUCTION
The Sensor Cable is a multi-conductor wire with embedded gold plated sensors every 3 feet. These sensors
act as extensions of the sensing probes contained within the Water Alert detector. Should any of the sensors come in contact with water the Water Alert will activate. Only 1/16" of water is necessary for detection.
The Sensor Cable comes in three standard lengths 12, 24 and 36 feet. One or Two Sensor Cables can be
connected to any Water Alert. These connections are made with a non-gender, locking connector for a
fast and durable installation. If desired, the cable may be kept in place along the floor with adhesive clips
(included). Figure 1 below shows the construction of WATER ALERT SENSOR CABLE.
Figure 1
(Actual size)
Non gender “locking” connectors
(to Water Alert detector)
Sensing probes
every 3 feet
End of line test button
(with protective cap)
0.2” diameter,
Rubber Jacket
for ultra-flexibility
Nickel Gold plated
sensing probes for
maximum corrosion
resistance.
The low voltage system is simple to install and is normally carried out by maintenance personnel with instructions furnished. Once installed, the system will provide years of maintenance free operation, guarding
24 hrs. a day against damaging water leakage.
* Not for use with "VR" Series Water Alert detectors.
Water Alert Sensor Cable does not absorb, trap or wick
moisture into the cable for detection unlike coaxial or helical type detection cables. This leads to excessive dry-out
periods, contamination by dissolved particles and mold and
mildew forming, requiring the cable to be uninstalled and
cleaned or replaced. This is one reason why our cable has
the lowest maintenance and longest warranty available.
8
MODEL #
SC-12
SC-24
SC-36
LENGTH
12'
24'
36'
SENSORS
PER CABLE
4
8
12
NEW! "VR" SERIESVandal Resistant with "Wash Down" Mode.
�
WATER LEAK DETECTION SYSTEMS
"VR" Models
-2 Models with optional accessories to meet
your specific requirements.
Respond in seconds...not hours!
- Specifically designed for use in public
and employee restrooms. (or any other
areas such as laboratories and clean rooms
that require frequent cleaning).
- Vandal and corrosion resistant design.
- "WashDown" mode enables the area to be
cleaned, without activating the Water Alert.
-All units tested 3 times during manufacture,
and come with a 5 Year Limited
Warranty. Made in the USA.
-Simple installation using instructions furnished with all equipment, normally done by
maintenance personnel.
- In wall or surface conduit wire entry.
MODEL VR-4 -
MODEL VR-2100 -
Water Alert detector provides isolated dry relay contacts (DPDT) which transfer and hold when activated.
Self-resets.
Water Alert detector used to tie-into all Dorlen Series 2100
Monitors
Powering options - 12 to 24 Volts AC or DC
(Power Supply available Model PS-4 see Pg. 25)
Powering options - Powered from Series 2100 monitor. (Pg. 11)
Audible alarm - None
Audible alarm - None
Relay contacts - None
Relay contacts - DPDT ( 2- Form C-Low Voltage )
Test feature- Yes
- 28 VDC@ 1 amp. MAX.
(For high power applications
see Pg. 26 model PR-WM)
Power draw - 20mA @ 9vdc.
Power draw - 25mA @ 24VAC.
9
�
WATER LEAK DETECTION SYSTEMS "VR" Models
PRINCIPLE OF OPERATION AND CONSTRUCTION "VR" MODELS.
The VR Series is activated by water or any conductive fluid bridging the sensors (A & A). Upon activation the external
L.E.D. indicator (B) will light RED. Once the liquid is removed, the VR Water Alert will self re-set. The VR Series is also equipped with
a "Wash Down Mode". This feature allows the area to be cleaned with water without activating the Water Alert. The Wash Down Mode
can be adjusted from 15 minutes to 2 hours. During this time the sensing circuit in the VR Water Alert is disabled. Once the Wash Down
Mode times-out, the VR Water Alert will automatically resume sensing liquid. To activate the Wash Down Mode, the cleaning personnel simply pushes the external piezo switch (C). This switch has no moving parts and is touch sensitive. The external L.E.D. (B) will light
Green, indication the VR Water Alert is now in Wash Down Mode.
�����
Vandal Resistant
cover screws
(Stainless steel)
�����
����
�
�
�� ���
����� ���
���
�
Extra heavy duty
Powder coated
aluminum housing
External View
����
�� �
�����
C
A
B
A
External L.E.D.
indicator
Wash Down Mode
Piezo Switch
(Stainless steel)
Water Sensing Probes
(Stainless steel)
Wire entry hole for "in wall" wire routing - All
hardware included.
Wash Down Mode
duration adjustment
15 Min to 2 Hours.
Wire entry hole for
"surface conduit"
wire routing.
(Conduit kit avaliableSee Page 28.)
Epoxy encapsulated
electronic circuit.
Internal View
Unit dimentions4.5"W x 2.25"H x 2.5"D
Weight- 1Lb.
Wire connection teminal block.
(Model VR-4 Shown)
10
Power ON
L.E.D. indicator.
Patent Pending
�
SERIES 2100
- Monitored Systems
The Series 2100 monitors.
General Description
The Series 2100 is an early warning leak detection system utilizing the latest line of Dorlen Products remote monitors and
compatible SS-2100 / VR-2100 Water Alert detectors. All Series 2100 Monitors monitor, power and test the connected
Water Alerts . The easily installed system is made up of only 3 separate components- 1 Monitor (7 models available) , up
to 40 Water Alert detectors, and Dorlen type "D" interconnect cable. Each system is characterized by the monitor used.
When one or more Water Alert detects water leakage it will activate and signal the monitor. The monitor will then activate
providing an audible alarm, red flashing lamp, LED indication of activated Water Alert(s) and transfer a dual set of isolated
relay contacts. The Water Alerts may be located up to 2500 feet from the monitor. Monitors are available in both shelf and
wall mount configuration.
Features common to all SERIES 2100 Monitors Monitors will monitor and power the
connected Water Alerts (Water Alert
Model SS-2100 or VR-2100).
Upon Water Alert activation, monitors sound audible alarm, flashing
red lamp and LED indication of
which Water Alert has activated.
Monitors are equipped with automatic internal battery back-up in
case of line power failure, system
will remain monitoring for up to 4
days without AC power... Battery self
recharges upon AC return.
Test Capability. This feature enables
the user to test the attached detectors
while at the Monitor location. By simply selecting an individual detector
and pressing the TEST push button,
that detector will activate, activating
the monitor. This test verifies all wiring is intact, Water Alert circuitry is
operating properly and the Monitor
has received the Water Alert signal.
This test simulates a water leak and
serves as a way to "exercise" the
system...thereby insuring that the
system is operating properly.
For help in system design, layouts or quotations, please contact
Dorlen's technical dept. at 1-414-282-4840 or dorlen@execpc.com
11
Monitors are equipped with 2SPDT isolated relay contacts
which will transfer upon any Water
Alert activation for customer use in
signaling existing security panels or
other equipment. (Relays rated at 1
amp, 28VDC). Optional independent
relays SPST for each channel available (ILR option...see price list).
Extremely simple installation...
Normally carried out by company
maintenance personnel with instructions furnished. ALL hardware
included.
Ultra-reliable performance;
All products come with a 5 year
Warranty...prices shown on attached
price list.
�
SERIES 2100
- Monitored Systems
����
�����
�����
�� �� ���
�����
������
� ��� ���
�
�����
Series 2100 Wall
Mounted monitor.
Screw type terminal connections on all monitors
to terminate “D” Cable.
WA
Dorlen type “D” cable (see p.28). 3 conductor #22 AWG, Stranded w/vinyl jacket.
(Also available in Plenum) 2500' max. distance between each Water Alert and the
Series 2100 monitor. (9vdc)
WA
TER ALERT
TER ALERT
Optional Sensor Cable,
an accessory to any
"SS" Series Water Alert detector.
See p.7-8.
SS-2100 or VR-2100
Water Alert detector
(SS-2100 shown)
SM-6(T)
SM-12(T)
WM-6(T)
WM-12(T)
6
12
6
12
2400 Sq. Ft.
3300 Sq. Ft.
4800 Sq. Ft.
6600 Sq. Ft.
2400 Sq. Ft.
3300 Sq. Ft.
4800 Sq. Ft.
6600 Sq. Ft.
WM-20(T)
WM-40(T)
20
40
8000 Sq. Ft.
11,000 Sq. Ft.
SM-12(AT)
12
Shelf Mount
Manual Test
(push button)
Wall Mount
6600 Sq. Ft.
Shelf Mount
12
P.13
P.13
P.14
P.14
P.15
P.15
Wall Mount
16,000 Sq. Ft. 22,000 Sq. Ft.
4800 Sq. Ft.
Automatic Test
P.16
DETECTOR
MODEL#
PHOTO AND
SPECIFICATIONS
TEST
CAPABILITY
FROM
MONITOR
MOUNTING
Water
Alerts
w/ Sensor Cable
MAX.
COVERAGE
AREA
Water
Alerts
Water Alerts
CHANNELS
Series 2100
Monitor
Model#
Max. # of
This table summarizes the Series 2100 product line.
SS-2100
or
VR-2100
�
SERIES 2100
MODEL SM-6(T) and SM-12(T)
- Monitored Systems
Monitors, powers and
tests 6 / 12 SS-2100 or
VR-2100 Water Alert
detectors.
-Shelf or Rack mounted
-Test feature
-Visual and audible alarms
-DPDT Relay contact outputs
-Battery back-up
- 5 Year Limited Warranty
-Made in the USA
The SM-6(T) and SM-12(T) are used to monitor areas 2400 to 6600 Sq. Ft.. The monitors are shelf or rack
mounted for simple installation. All hardware, installation/maintenance manuals and warranty are included
with the monitor.
See pages 11 and 12 for a general description
and detailed features of all Series 2100 Monitors.
Rear View SM-6(T) and SM12(T)
SM-6(T) AND SM-12(T)
SPECIFICATIONS
Monitor Input Voltage/Current: 115VAC 10%, 60Hz, .2Amp
max.
Monitor Output Voltage: 9VDC (To detectors)
Monitor Audible Alarm: 85db at 3 feet
Input: UL Listed wall adaptor
Dimensions / Wt. SM-6(T): 8.5"Wx9.5"Dx2.5"H / 7lbs
Dimensions / Wt. SM-12(T): 17"Wx12"Dx3.5H / 20lbs
Construction: All aluminum, textured oven baked finish
Panel- off white, Housing- blue.
Screw type terminal strip wire connection.
Warranty: 5 Year Limited
13
�
SERIES 2100
MODEL WM-6(T) and WM-12(T)
- Monitored Systems
Monitors, powers and
tests 6 / 12 SS-2100 or
VR-2100 Water Alert
detectors.
-Wall mounted
-Test feature
-Visual and audible alarms
-DPDT Relay contact outputs
-Battery back-up
- Key Reset switch
- 5 Year Limited Warranty
-Made in the USA
The WM-6(T) and WM-12(T) are used to monitor areas 2400 to 6600 Sq. Ft.. The monitors are surface wall
mounted for simple installation. All hardware, including a 5 ft. length of wire duct, installation/maintenance
manuals and warranty are included with the monitor.
See pages 11 and 12 for a general description
and detailed features of all Series 2100 Monitors.
Internal View - WM-12(T)
WM-6(T) AND WM-12(T)
SPECIFICATIONS
Monitor Input Voltage/Current: 115VAC 10%, 60Hz, .2Amp max.
Monitor Output Voltage: 9VDC (To detectors)
Monitor Audible Alarm: 85db at 3 feet
Input: UL listed input transformer, Terminal strip hard wired.
Dimensions: 10"Wx5"Dx12"H
Weight: 20lbs.
Construction: NEMA 4 steel, Oven baked textured beige finish.
Screw type terminal strip wire connection.
Warranty: 5 Year Limited
14
�
SERIES 2100
- Monitored Systems
MODEL WM-20(T) and WM-40(T)
Monitors, powers and
tests 20 / 40 SS-2100 or
VR-2100 Water Alert
detectors.
-Wall mounted
-Test feature
-Visual and audible alarms
-DPDT Relay contact outputs
-Battery back-up
- 5 Year limited Warranty
-Made in the USA
The WM-20(T) and WM-40(T) are used to monitor areas 8000 to 22,000 Sq. Ft.. The monitors are surface wall
mounted for simple installation. All hardware, including a 5 ft. length of wire duct, installation/maintenance
manuals and warranty are included with the monitor.
See pages 11 and 12 for a general description
and detailed features of all Series 2100 Monitors.
Internal View WM-20(T)
WM-20(T) AND WM-40(T)
SPECIFICATIONS
Monitor Input Voltage/Current: 115VAC 10%, 60Hz, .2Amp
max.
Monitor Output Voltage: 9VDC (To detectors)
Monitor Audible Alarm: 85db at 3 feet
Dimensions / Wt. WM-20(T): 20"Wx4.75"Dx15.5"H / 35lbs.
Dimensions / Wt. WM-40(T): 20"Wx4.75"Dx24H / 50 lbs.
Construction: 16 Gauge NEMA 12 Slimline enclosure,
textured oven baked finish, off white.
Screw type terminal strip wire connection.
Surface wall mount - no need for wall cut-out. Surface wire duct
included.
Warranty: 5 Year Limited
15
�
SERIES 2100
- Monitored Systems
MODEL SM-12(AT)*
Monitors, powers and
auto-tests 12 SS-2100
or VR-2100 Water Alert
detectors.
-Shelf mounted.
-AUTOMATIC TEST feature
-Visual and audible alarms
-Relay contact outputs
-Battery back-up
- 5 Year limited Warranty
-Made in the USA
Monitor/Power Supply Provides Remote Indication of
Water/Liquid Leakage Plus Capability of PERIODIC AUTOMATIC
TESTING of the Individual Water Detectors from the SM-12(AT)
Location . . . Especially Suitable for Large Critical Installations
where manual testing is undesirable.
See pages 11 and 12 for a
general description and detailed features of all Series
2100 Monitors
The SM-12(AT) can monitor and power up to 12 Water Alerts and will provide an alarm signal (red flashing LED's, audible
buzzer, and relay outputs) if any sensor is activated. In addition, the unit will automatically scan test all the connected
detectors at preset time intervals. The periodic scan test sends a test signal out to each detector in sequence. The Test
Scan can be set for Weekly, Daily or Repetitive intervals. Capable of Manual Scan Initiate also. The System can be operated with less than 12 detectors. A sensing circuit in each Water Alert receives the test signal and electronically switches
in simulated water conductivity across its sensing probes. A properly working Water Alert will send back a return signal.
Any Water Alert which does not properly respond to the scan signal will be indicated. Each test scan of the SM-12(AT)
assures that: all system wiring is intact and that the water sensing and send back circuit of all Water Alerts are operating
properly. This scan test automatically "exercises" the total system...which goes beyond other supervised systems.
Provides separate isolated relay contacts for customer use if water is detected or if any Water Alert fails the scan test.
Any detector sensing water will transfer the "Water Alert Activated" latch relay (SPDT). (This relay will not transfer as a
consequence of the scan test) . . . Any detector failing the scan test will transfer the "Scan Fail" latch relay (SPDT). Relay
contacts are brought out to marked rear panel terminal strips. Contact rating 1 amp, 28vdc resistive.
Specifications for all products are available for download at www.wateralert.com
*Formerly RI-2(AT)
16
CEILING GUARD
R
WATER LEAKAGE SENSING SYSTEM
Dorlen Products' Ceiling Guard system is your best defence
to guard against water leakage coming from above your
ceiling. Wether its a leaky roof, pipe leaks or above floor
flooding, Ceiling Guard will provide early warning of the
potential disaster, aiding in rapid response!
����
�����
�� �
�����
�����
����
�
�
�� ���
����� ���
���
�
INTRODUCTION
The Dorlen Products’ Ceiling Guard Water Leakage Sensing System is used to sense small amounts of water/liquid leakage
above 2’x4’ or 2’x2’ suspended acoustical ceiling tiles. The system is made up of low profile (1/2” ht.) “troughed” sensing trays
which contain small sensing contacts. These trays are fastened to the top side of the conventional drop-in ceiling tiles and are
interconnected to form zones of protection...The zones, in turn, are terminated in a Dorlen
detector.
R
The system is designed to detect and provide indication of small
amounts of leakage before the leakage accumulates to the point of
leaking through, or along the edges of the tiles to the area below.
Installing Ceiling Guard provides a very high degree of protection
against leakage from concealed piping and the roof or floors above
the suspended ceiling.
Installation is very simple, while individual panel removability
and overall ceiling appearance is retained. Ceiling Guard can be
used with new or existing suspended ceilings. Ceiling Guard is
an extension of, and works in conjuction with Dorlen’s Water Alert
detectors.
R
Top view of 2x4 Ceiling
Guard Sensing Tray
Top view of 2x2 Ceiling
Guard Sensing Tray
17
CEILING GUARD
R
SERIES 2000 - Ceiling and Ceiling/Floor - Monitored Systems
PRINCIPLE OF OPERATION
Each Ceiling Guard sensing tray contains small sensing contacts. The sensing contacts are parallel connected together
on the underside of the sensing tray. The ends of the tray have panel-to-panel connectors which are engaged to adjacent
trays during installation. If all trays in an array or zone are dry, a very high electrical resistance exists across the sensing
contacts. Should any tray come in contact with water, the electrical resistance changes abruptly. This resistance change
is detected at the end of the connection by a Dorlen Water Alert Detector. In most cases the Water Alert is Dorlen’s Model
CSS-2000 (See Series 2000 description pgs. 19-24.)
The flame retardant plastic sensing trays making up Ceiling Guard are sized to cover either the conventional 2’x4’ or 2’x2’
ceiling tiles. The smallest amount of water leakage into any sensing tray quickly finds its way to a sensing contact located
in the trough of the tray thereby activating the associated detector.
Galvanized barbed
fasteners or staples
(provided) fasten trays to
Non-Gender Panel-to Panel connector (any
End ribs stiffen
connector engages any other)
panel and retain
- Latched engage/release
liquid leakage
-Gold plated contacts
ceiling tiles
To CGM Series
2000 Monitor
CSS-2000 Water Alert Detector.
Each Zone (up to 5 tray packs,
320 sq.ft.) will terminate in a
detector which provides audible
Non-corrosive, gold plated sensing
alarms for water sensed or sens-
contacts covered by dust covers
ing tray cable break, and signals
Ceiling Guard Monitor (CGM)
alarm panel.
TYPICAL ABOVE CEILING VIEW
18
CEILING GUARD
R
SERIES 2000 - Ceiling and Ceiling/Floor - Monitored Systems
General Description
The Series 2000 is an early warning leak detection system utilizing the latest line of Dorlen Products "CGM"monitors and
compatible CSS-2000 / SS-2000 Water Alert detectors. All Series 2000 Monitors monitor, power and test the connected
Water Alerts . The easily installed system is made up of only 4 separate components- 1 Monitor (4 models available) ,
up to 40 Water Alert detectors, Ceiling Guard Sensing Trays and Dorlen type "E" interconnect cable. When one or more
Water Alert detects water leakage it will activate and signal the monitor. The monitor will then activate providing an
audible alarm, red flashing lamp, LED indication of activated Water Alert(s) and transfer a set of isolated relay contacts
(SPDT). The Water Alerts may be located up to 2500 feet from the monitor. Monitors are available in both shelf or wall
mount configuration.
Features common to all SERIES 2000 "CGM" Monitors A single low voltage cable (.15” OD) from
each CSS-2000 ceiling detector (or SS2000 floor detector) to a Ceiling Guard
Monitor panel simplifies wiring.
Both the CSS-2000 ond SS-2000 detectors are powered from the CGM’ monitor thereby eliminating need for batteries
within the detectors.
The detctors are testable from the CGM’
location. Simple push button test verifies that: A.) leakage detection circuitry
is working properly and B.) zone supervision circuitry is working properly. This
test also verifies proper operation during
initial installation and at any later date to
“exercise the system.”
The CGM’ monitor provides isolated dry
relay contact output (SPDT) if leak is
detected...2nd relay output if zone wiring
is disrupted (supervision). Relays are rated
28VDC. Max. at 1 amp.
A momentary or intermittent water leak is
latched into the CGM’ monitor until manually reset.
CGM’ monitor provides visual and audible
alarms with LED indication of activating detectors. ( water leak sensed or tray system
wiring disrupted)
Rechargeable battery back-up...2 day
monitoring without AC power...Battery
recharges upon AC line return.
CGM-6(T) and CGM-12(T) are shelf
mount type enclosers. CGM-20(T)
and CGM-40T) are wall mount type.
5 Year limited warratnty. Made in the
USA.
For help in system design,
layouts or quotations, please
contact Dorlen's technical
dept. at 1-414-282-4840 or
dorlen@execpc.com
CSS-2000-For use with Ceiling Guard sensing
trays, in terminating zone. Provides audible
alarm for water leak sensed and zone wiring
break (supervized). Requires Dorlen Type
“E “ cable (5 conductor #24 w/shield) for tie
into CGM.
SS-2000-For use on floors, provides audible
alarm . Requires Dorlen type”D” cable,
(3 cond. #22) for tie into CGM Monitor.
CSS-2000 Ceiling
Water Alert Detector
SS-2000 Floor
Water Alert Detector
19
CEILING GUARD
R
SERIES 2000 - Ceiling and Ceiling/Floor - Monitored Systems
Zone 6
Zone 4
WA#6
Zone 5
WA#4
WA#3
2’x4’ Sensing Panels (1 tray pack per
zone shown, 5 tray packs per zone max..
Water Alert Detectors may be up
to 2500’ft. from CGM’ monitor.
WA#5
Z
o
n
e
Ceiling Guard
Monitor CGM-12(T)
3
WA#2
Z
o
n
e
WA#1
2
Zone 1
Top view of typical ceiling plan, 6 Zone. ( 1 tray pack per Zone shown, 5 tray packs per Zone maximum.)
SERIES 2000 COMBINED CEILING / SUB-FLOOR MONITORING
Because often times there is a water leak threat from above the ceiling as well as below the raised floor, many users make up “combined” systems. Two typical combined ceiling/sub-floor monitoring systems are shown in figure
below.
Ceiling Guard
terminated with
CSS-2000 Water
Alert Detectors
Ceiling Guard
terminated with
CSS-2000 Water
Alert Detectors
AD-6
Auto-Dialer
CGM-12(T)
Monitor
SS-2000 subfloor Water Alert
detectors with
Sensor Cable.
SS-2000 subfloor Water Alert
detectors.
Series 2000 with Dial-out (AD-6)
CGM-40(T) Monitor
tied into existing
security system.
Large Series 2000 system
20
CEILING GUARD
R
SERIES 2000 - Ceiling and Ceiling/Floor - Monitored Systems
CGM-6(T)
Monitors and powers up to 6 CSS-2000 or SS-2000 Water
Alert detectors. Includes Test feature, audible and visual
alarms, and isolated relay contacts for water leak sensed
or sensing tray cable break. Shelf mounted.
17"W x 12"D x 3.5"H. 8 Lbs.
CGM-12(T)
Monitors and powers up to 12 CSS-2000 or SS-2000 Water Alert detectors. Includes Test feature, audible and visual
alarms, and isolated relay contacts for water leak sensed or
sensing tray cable break. Shelf mounted.
17"W x 12"D x 3.5"H. 8 Lbs.
CGM-20(T)
Monitors and powers up to 20 CSS-2000 or
SS-2000 Water Alert detectors. Includes Test feature, audible and visual alarms, and isolated relay contacts for water
leak sensed or sensing tray cable break. Wall mounted.
20"W x 15.5"H x 4.75"D. 25 Lbs.
CGM-40(T)
Monitors and powers up to 40 CSS-2000 or
SS-2000 Water Alert detectors. Includes Test feature, audible and visual alarms, and isolated relay contacts for water
leak sensed or sensing tray cable break. Wall mounted.
20"W x 24"H x 4.75"D. 35 Lbs.
CGM-6(T)
CGM-12(T)
CGM-20(T)
NOTE: For small areas (less
than 1000 sq. ft., typical) a
monitor may not be desired.
Contact Dorlen for a data sheet
on non-monitored Ceiling Guard
systems.
SHELF MOUNT - Units plug into 120VAC outlet(.1
amp). Detector wiring connects to rear panel marked
screw-type terminal strips. Rugged attactive enclosure with textured oven baked finish. UL listed line
cord adaptor.
WALL MOUNTS - Unit hard-wired or plug into 120VAC
wall outlet (.5 amp max.). Detector wiring connects
to interior marked screw type terminal blocks. Prepunched mounting holes and surface wiring duct
and opening provided. 16 gauge NEMA 12 slimline
enclosure with textured polyester powder finish. Key
lock optional.
Surface wiring duct channel and trim kit provided for
detector wiring drop from ceiling.
CGM-40(T)
CGM-40(T) Internal view
21
Surface wall mount - no need for wall cut-out.
CEILING GUARD
R
SERIES 2000 - Ceiling and Ceiling/Floor - Monitored Systems
HOW CEILING GUARD IS INSTALLED:
GENERAL
Installation Instructions are furnished with the particular type of equipment that is ordered. An overview of the general
installation procedure follows.
Each Ceiling Guard Tray Pack is comprised of eight 2' x 4' trays (CG24) or sixteen 2'x 2' trays (CG22). The trays come
with prewired sensing contacts and panel-to-panel connectors. Galvanized barbed fasteners for affixing the trays to the
users ceiling tiles are furnished.
Upon receipt of Ceiling Guard Tray Packs and the associated detectors and monitor(s) , the user removes the ceiling tiles
from the suspended grid, (assuming an existing ceiling), fastens the individual trays to the ceiling tiles, re-installs the panels
and interconnects panels according to the Installation Instructions furnished. Up to five tray packs may be interconnected
to form a zone. One end of the zone will terminate in a CSS-2000 Water Alert. All CSS-2000 and SS-2000 Water Alerts
will tie into the CGM Monitor.
There are a few special considerations to be observed relative to installation as described in the following paragraphs.
SPECIAL CONSIDERATIONS
A drop-in ceiling does not consist of strictly 2'x 4' or 2'x
2' tiles but rather there normally are "trimmed down" tiles
along one or more sides of the room. Also, there are
"lay-in" lamp fixtures, Heating/AC diffuser outlets, and
sometimes sprinkler heads, halon heads and/or smoke
detectors.
In the case of lay-in lamp fixtures, the installer fastens
strips of plastic sheet (provided) to the sloping edge(s) of
the lamp fixture by means of duct tape. This is done prior
to installing the adjacent sensing panel. The sensing panel
is installed under the plastic sheet. This arrangement has
the effect of diverting leaking water from above the lamp
fixture to the adjacent sensing tray. (See Pictorials p.23).
Heating/AC diffuser outlets may be handled similarly.
Trimmed down ceiling tiles are handled in two ways. If
the dimensions of the trimmed tile are significant (greater
than 13"), the sensing tray is trimmed to fit the reduced
size ceiling tile. The trimmed tray is then fastened to the
trimmed ceiling tile.
If the ceiling tile is trimmed to a narrow strip (less than 13"),
duct tape is used to affix a strip of plastic sheet to the wall
so as to divert leakage into an adjacent tray.
Where sprinkler-heads or smoke detectors exist; piping,
conduit, junction boxes, etc. may pass through the existing ceiling tile. In these situations the installer makes
appropriate cut-outs in the sensing tray to allow the obstruction to pass thru the sensing tray. From the adjacent
panel opening, rubber sealer (furnished) is used to seal the
obstruction to the sensing tray. (Page 23.)
View of 1500 sq. ft. computer room after Ceiling
Guard installed.
22
CEILING GUARD
R
SERIES 2000 - Ceiling and Ceiling/Floor - Monitored Systems
Sensing panel
2' x 4'
Fluorescent
lay-in light
fixture
Duct Tape Seal
(Furnished)
Duct Tape
Cut out middle sensing
contact if there is mechanical interferrence
with pipe
Cut Dorlen tray to allow
in place installation
Existing sprinkler
head supply pipe
Seal with Butyl rubber
sealer & tape
(furnished)
Deflector
Sensing panel
Fasten tray to ceiling tile at all four corners
SPRINKLER HEAD CG INSTALLATION
FLUORESCENT LIGHT CG INSTALLATION
Sensing panel
Bundled home-run wires (Type
"E") to CGM monitor panel
Panel wire connectors
snap together to form “zones”
"T" Grid
(Rings furnished)
Sensing panel
BRIDAL RING WIRING
PANEL-TO-PANEL INTERCONNECT
Required materials:
If you have 2'x 4' tiles, Model CG24 is the proper Tray Pack to order. If you have 2'x 2' tiles, Model CG22 is the proper Tray Pack to order.
Prior to ordering, verify that your ceiling is or will be (new construction) made up of either 2'x 4' or 2' x 2' removable ceiling tiles, i.e......the tiles are supported in a suspended grid system and can be removed by lifting and dropping out of the suspended grid.
COMPLETE COVERAGEBy count, or using a ceiling plan, (sketch one up if necessary), determine how many tiles require sensing trays to protect the room below.
PARTIAL COVERAGEBy count, or using a ceiling plan/equipment location diagram (sketch up if necessary), determine how many tiles require sensing trays to protect the
equipment below.
In taking the count in either of the two above situations, the existing tiles along the border of the room may be narrower than the standard size. Count
these as full tiles. If the tiles contain sprinkler heads or smoke detectors, include these in your tile count. Do not count lay-in 2'x 4' (2'x 2') lamp fixtures
or A/C Heating diffusers.
TRAY PACK COUNTIn the case of 2' x 4' tiles, divide the panel count taken above by 8 to determine how many CG24 Tray Packs are required.
In the case of 2' x 2' tiles, divide the panel count taken above by 16 to determine how many CG22 Tray Packs are required.
DETECTORSEach ceiling guard “zone” will terminate in a CSS-2000 detector, zone size may vary, but a maximum of 5 tray packs must be followed. If SS-2000 floor
detectors are required, a good rule of thumb is 1 detector for 300sq. ft..
CGM’ MONITORThe CGM’ Monitor selected should have a zone capacity (channels) equal to or exceeding the detector count taken above (CSS-2000 and SS-2000) .
Only a single detector only can be connected to a given zone (channel) input.
23
CEILING GUARD
R
SERIES 2000 - Ceiling and Ceiling/Floor - Monitored Systems
ADVANTAGES OF CEILING GUARD:
Dorlen Products conceived and developed the Water Alert leakage detection system in 1975. Since that time, tens of thousands of
units have been installed and much experience has been gained. Based on this experience, various techniques have been tested
and evaluated by Dorlen Products to arrive at the most practical and reliable approach to use in acoustical tile ceiling applications.
The result of this effort has been the patented Ceiling Guard system. The foremost advantages of Ceiling Guard are:
The flame-retardant -PVC plastic trays affixed to the
top of the tiles present a low profile (only 1/2" above
the tile). This low profile avoids interference with piping,
ductwork, conduit, "T" grid suspension wires, etc.
The Ceiling Guard System is low in cost. The avoidance of a single spill over critical equipment could well
pay for the system many times over.
The system is low voltage and easy to install...can be
installed by maintenance type personnel.
Simple removability of individual panels is retained
after the system is installed.
The troughed trays, by guiding the leakage to the sensing contacts, provide a very high degree of protection.
The tray end ribs being "closed" serve to trap the leakage water further insuring detection of minute amounts
of leakage.
The overall appearance of the ceiling is unaffected.
The system will not activate due to high humidity.
5 Year Limited Warranty.
12,000 sq. ft. Data Center...Complete Coverage with Ceiling
Guard.
University Rare Book Library...Ceiling Guard coverage over all
bookshelves.
24
ACCESSORIES / OPTIONS
WATER ALERT POWER
SUPPLY, MODEL PS-3
DC power supply eliminates batteries in "SS"
Series Water Alert detectors - ideal for large
installations where accessibility to Water Alert
is inconvenient or battery operation is not acceptable. Output- 9vdc
FEATURES
Operates up to 24 Water Alert detectors, wiring instructions furnished.
Internal self-recharging battery provides
back up power to system in event of line
failure or power cord removal.
UL Listed input transformer.
PS-3 w/ Model SS Water Alert
Flashing LED indicating power to
Water Alerts.
Large screw-type terminal blocks at
rear of enclosure for convenient wiring.
Connection to Water Alerts is made by
means of wire nuts.
Short circuit, overload and over
voltage protected.
Rugged, attractive enclosure 8.5" W x
9.5" D x 2.5" H.
WATER ALERT POWER
SUPPLY, MODEL PS-4
DC power supply for VR-4 Water Alert
detectors. Output - 12vdc
FEATURES
Operates up to 24 Water Alert detectors, Model VR-4. Wiring instructions
furnished.
Internal self-recharging battery provides
back up power to system in event of line
failure or power cord removal.
UL Listed input transformer.
PS-4 w/ Model VR-4 Water Alert
Flashing LED indicating power to
Water Alerts.
Large screw-type terminal blocks at
rear of enclosure for convenient wiring.
Connection to Water Alerts is made by
means of wire nuts.
25
Short circuit, overload and over
voltage protected.
Rugged, attractive enclosure 8.5" W x
9.5" D x 2.5" H.
ACCESSORIES / OPTIONS
VOLTAGE MODULE
MODEL VM-1
Rather than battery power it may be desirable to power "SS" Series Water Alerts
with your 12 or 24V AC or DC ( or any voltage in between). A Voltage Module will
be required for each detector in this
POWER RELAY / POWER
SUPPLY MODEL PR-WM
The Voltage Module accepts
12-24v AC or DC to power "SS"
Series Water Alert Detectors
application. The Voltage Module snaps
into the Water Alert and will convert your
voltage to 9VDC as required.
Used to control high powered equipment such as pumps, motors and solenoids from a SS-4, SS-5 and VR-4
Water Alert Detectors.
FEATURES
Unit is surface wall mounted in a NEMA
4x nonmetallic encloser. Dimensions5.5" H x 3" W x 2.6" D
Output: SPDT Relay Contact ( Form C)
Rated - 120VAC @ 20 Amps.
Unit will power up to 2 Water Alert detectors Model SS-4, SS-5 and VR-4.
Large screw-type terminal blocks inside
enclosure for convenient wiring. Connection to Water Alerts is made by means
of wire nuts.
UL Listed input transformer.
Input: Normally Open Contact
(from SS-4, SS-5 and VR-4)
REMOTE ALARM
MODEL RA-WM
Power ON LED, Relay Activated LED.
Used for additional indication of water leakage.
Compatible with all Series 2100 monitors and SS-4,
SS-5 and VR-4 Water Alert Detectors.
FEATURES
Unit is surface wall mounted.
dimensions- 6"H x 3"W x 2"D
85db Audible Alarm w/silence
switch
UL Listed input transformer.
Input: Normally Open Contact
10mm LED indicator
26
ACCESSORIES / OPTIONS
AUTO-DIALER
MODEL AD-6
Provides Off-Premise Indication of Water/
Liquid Leakage and other Emergency Conditions.
The AD-6 is a new state-of-the-art automatic
telephone dialer and annunciator that is designed for use with various alarm devices. The
AD-6 automatically dials a sequence of user
programmed phone numbers (maximum of
eight) and provides a custom voice message
indicating the emergency condition which exists at the dialer location (building, small business, office, computer room, etc.)
Applications include private, commercial, institutional and industrial situations - providing a
warning, especially at night, that an emergency
situation exists, and allowing the called party to
take immediate action to prevent or minimize
damage or financial loss.
The AD-6 Auto-Dialer is compatible with a
number of Water Alert combinations and also
standard alarm devices which provide contact
opening or closure. The remote devices are
connected to the AD-6 by means of low voltage pairs of wire. Three individual inputs are
available to monitor groups of contact operating
devices. As example, the #1 input may be used
to monitor a group of Water Alerts or Dorlen
Remote Monitor, #2 input standard intrusion
devices (normally closed contacts open) and #3
fire-detecting devices (normally open contacts
close). Alternatively, three different zones of
Water Alert groups may be used to activate
the three inputs for dialer operation dedicated
exclusively to water leakage detection. High
and low temperature limits can also be programmed into the AD-6 (single temperature
sensor included).
Upon activation of any of the three monitored
inputs, the AD-6 will locally announce the Alert
Condition for 30 seconds. If the "Alarm Cancel"
switch is not pressed (i.e.; personnel are not
present) the AD-6 will commence the dial-out,
calling each of eight numbers sequentially. The
first party answering the dial-out acknowledges
receipt of the Alert Condition message by entering an acknowledgment code. This terminates
the dial-out for this condition. The AD-6 will
call continuously in the above fashion waiting
one minute between each number dialed until
acknowledged.
AD-6 Auto-Dialer
Simple Installation
Connect alarm devices to marked
AD-6 internal terminal strip.
Plug AD-6 UL Listed adaptor into
120VAC wall outlet.
Open door and program the phone
numbers to be called via the small
internal key pad.
Close door and plug AD-6 miniature
plug into existing RJ-11 telephone
jack and verify operation per instructions.
May be used directly with Dorlen Water
Alert models SS-4, SS-5, VR-4 or any
Dorlen remote monitor, Series 2100 or
Series 2000.
Dialer announces both locally and
over the telephone line which "Alert
Condition" is activated, i.e. #1, #2 or
#3 ...Will also dial out if a temperature
limit is reached, AC power is lost (after 5
minutes delay) or if battery is low. Works
with rotary or touch tone service.
27
Dialer may be called from any off-premise location. The dialer will answer and
state status of the three Alert Conditions,
temperature existing at dialer, AC power
(on or off) and battery condition (OK or
low).
Easily programmed using internal
keyboard. Tamper resistant ... cannot
change dial-out phone numbers with
password protection if desired.
Rechargeable back-up battery included.
Backs up dialer for 15 hours should AC
line fail. Upon AC power return, battery
automatically recharges.
Protected against high electrical noise
ambient (heavy electrical machinery,
etc.)
Rugged, attractive "Wall Mount" enclosure, 7.25" W x 4.5" D x 11.25" H.
Weight: 8 lbs. UL Listed line cord adaptor - FCC approved.
Complete instructions furnished. The
AD-6 comes with a 5 Year Limited
Warranty.
ACCESSORIES / OPTIONS
ELECTRIC ACTUATED
VALVES
-
Normally open valve
400 PSI Max.
1/2" to 2" sizes available
110 to 120VAC operation
Full port design
Triple stem seal design
NTP Threaded Ends to ANSI B2.1
Permanently Lubricated
Thermal overload protection
35 F to 135 F operation
ISO 5211 Mounting
Valves are manufactured by DuraValve
Inc.. Dorlen Products Is an authorized
re-seller. Valves are covered by a 1
year warranty from DuraValve Inc.
CONDUIT KITMODEL VR-KIT
Used to shut off water supply once water
leakage has been detected. For use with
Model SS-4, SS-5, VR-4 or any Series
2100 monitor. PR-WM Power Relay
also required (see page 26).
Size
Model#
1/2"
EAV-1/2
3/4"
EAV-3/4
1"
EAV-1
1 1/4" EAV-1-1/4
1-1/2" EAV-1-1/2
2"
EAV -2
Used with VR-4 and VR-2100 for
surface conduit wire routing.
(For VR series Water Alert)
The kit includes 25 feet of non-metalic corrosion proof 3/8" conduit, a 90 degree water
tight conduit fitting, 4 stainless steel conduit
straps and 8 stainless steel strap screws.
Also included is a 1/8 inch masonary drill
bit. The Satinless steel strap screws are
also tamper resistant.
CABLE AND WIRE
TYPE "B" CABLE
Signal/Power wire - 2 conductor twisted pair, stranded #22 AWG. with vinyl jacket. 0.165" O.D. For use in Water
Alert to AD-6 signal, PS-3 and PS-4 power runs less than 500'.
TYPE "D" CABLE
Signal/Power wire - 3 conductor, color coded, stranded #22 AWG. with vinyl jacket. 0.164" O.D. For use with
all Series 2100 systems. (SS-2100 or VR-2100 Water Alert to Series 2100 Monitor.)
TYPE "E" CABLE
Signal/Power wire - 5 conductor, color coded, stranded #24 AWG. with vinyl jacket. 0.150" O.D. For use with
all Series 2000 Ceiling Gurad systems. (CSS-2000 to CGM)
TYPE "G" CABLE
Signal/Power wire - 6 conductor, color coded, stranded #24 AWG. with vinyl jacket. 0.150" O.D. For use with
VR-4 Water Alerts.
POWER WIRE #18
Power wire - 2 conductor twisted pair, stranded #18AWG. with vinyl jacket. 0.226" O.D. For PS-3 and PS-4
power runs between 500' and 2500'.
NOTE: Plenum rated cable and wire available; see price list.
28
DORLEN PRODUCTS, INC. FIVE YEAR LIMITED WARRANTY
AND TERMS AND CONDITIONS OF PRODUCT SALE
Limited Warranty
Dorlen Products, Inc. (“Seller”) warrants its products to be free from defects in materials and workmanship under normal use and
service for five (5) years from the date of original purchase. Seller agrees to repair or replace, at its option without charge to the original purchaser, any Dorlen Products that does not conform to this Limited Warranty. Seller shall not have any obligations under this
Limited Warranty, or otherwise, if the Dorlen Product has been altered, or has been improperly installed, maintained or used, or has
been repaired by persons other than Seller. Improper use or modifications of any Dorlen Product voids this warranty. 9 Volt alkaline
and internal 12volt batteries and any other batteries are not covered by this warranty. DuraValves are not covered by this warranty. For
warranty service, return your Dorlen Product, shipped pre-paid to Seller. Please include all company information and return address.
THIS IS SELLER’S SOLE WARRANTY. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE, OR OTHERWISE, WHICH EXTEND BEYOND THIS
LIMITED WARRANTY. IN NO EVENT WILL DORLEN PRODUCTS, INC. BE LIABLE TO PURCHASER OR ANYONE
ELSE FOR CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, PROPERTY DAMAGES, WATER DAMAGES,
LOSS OR DAMAGE OF ELECTRONIC DATA OR COMPUTER STORED MEDIA, LABOR OR REPAIR COSTS, LOST
PROFITS, BUSINESS INTERRUPTION DAMAGES, COMPENSATORY DAMAGES, PUNITIVE DAMAGES, OR OTHER
LOSSES OR DAMAGES OF ANY KIND OR DESCRIPTION RESULTING FROM PURCHASE, INSTALLATION, USE,
OR FAILURE OF ANY DORLEN PRODUCT. THIS EXCLUSION OF ANY OTHER WARRANTY AND EXCLUSION OF
LIABILITY FOR DAMAGES APPLIES TO ALL EVENTS AND OCCURRENCES, EVEN IF THE LOSS OR DAMAGE IS
CAUSED BY SELLER’S OWN NEGLIGENCE, FAULT OR BREACH OF PRODUCT WARRANTY.
PRODUCT PERFORMANCE: All Dorlen Products are carefully manufactured, inspected and tested prior to shipment by Seller
and are expected to perform as warranted. However, Seller has no control over actual installation and use of Dorlen Products. Seller
does not inspect the Purchaser’s use, installation or maintenance of Dorlen Products. Seller does not warrant or represent that all
products it sells will always perform exactly as expected and will never fail. Product purchaser understands that there are installations,
events and circumstances where properly manufactured Dorlen Products may fail to detect potentially damaging environmental conditions, including water leakage or moisture, or may fail to provide an alarm, due to technical limitations of the customer’s installation
and product use which are beyond the control of Seller. The Seller does not provide insurance for Purchasers and does not guarantee that there will never be occasions under which the product user may sustain losses, water damage or injury following purchase,
installation or use of a Dorlen Product. SELLER SHALL HAVE NO LIABILITY WHATSOEVER FOR PROPERTY DAMAGES, INJURY OR LOSS BASED ON ANY CLAIM THAT DORLEN PRODUCT(S) FAILED TO GIVE WARNING OR
ALARM. IN ANY CIRCUMSTANCES OR JURISDICTIONS WHERE SELLER MAY NONETHELESS BE HELD LIABLE
FOR LOSSES OR DAMAGES ARISING OUT OF PURCHASE, USE OR INSTALLATION OF A DORLEN PRODUCT, IN
THAT EVENT, SELLER’S MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE OF THE
DORLEN PRODUCT(S), OR $500, WHICHEVER AMOUNT IS GREATER. THE PRODUCT(S) PURCHASER, AND ANY
SUCCESSORS OR ASSIGNS INCLUDING INSURERS PAYING LOSSES OR DAMAGES, DO HEREBY RELEASE AND
DISCHARGE DORLEN PRODUCTS, INC. AND SELLER FOR ANY AND ALL DAMAGES, LIABILITIES AND OBLIGATIONS IN EXCESS OF THIS STATED LIMITATION OF DAMAGES.
INDEMNIFICATION: Purchaser agrees to this Limited Warranty, and the exclusions of liability and limitations of damages stated
herein and acknowledges that the price paid for Seller’s product includes these Terms and Conditions of Product Sale. In the event
that a lawsuit is filed or any claim is made against Dorlen Products, Inc. or its officers and employees demanding payment for damages, injuries, losses, or cost rising out of Purchaser’s installation or use of a Dorlen Product, Purchaser agrees to fully indemnify, defend
and hold harmless Seller upon such lawsuit or claim, including Seller’s attorney fees and legal costs, regardless of whether the claimed
damages are caused by Seller’s own negligence or fault, or otherwise.
RETURN POLICY: All returns are subject to a 10% restocking fee. No returns after 60 days of shipment date.
PURCHASER’S ACCEPTANCE OF TERMS AND CONDITIONS: By ordering and using Sellers product(s), the Purchaser irrevocably accepts Seller’s Limited Warranty and these Terms and Conditions, without modification. Any contrary, inconsistent, or
competing Terms and Conditions stated in customer’s Purchase Order and/or purchasing documents are expressly rejected and not
accepted by Dorlen Products, Inc. By keeping your purchased Dorlen Product(s) for ten (10) days or longer after product delivery,
the Purchaser acknowledges, agrees to, and fully accepts this Limited Warranty and all stated Terms and Conditions of product sale
including the Product Performance and Indemnification provisions.
29
Previously Manufactured Products - This catalog describes the latest line of Dorlen Water Alert detectors and monitors.
It is recommended these products be used for new installations. However, if you are expanding an existing installation
and require any previously manufactured product these are available... Please request pricing on the specific product(s).
Dorlen's systems are extremely reliable, easy to install and have a 5 year limited warranty.
We are the leader in water leak detection and have been in business for over 30 years...
Over 21,000 sites in the U.S. have Water Alert systems installed!
For help in system design, layouts or quotations, please contact Dorlen's technical dept. at 1-414-282-4840 or dorlen@execpc.com.
PREVENT DOWNTIME AND DAMAGE!!
HOW TO ORDER
Orders may be placed by phone, fax, or mail (to
address below) on your company order form.
ALL PRICES:
FOB MILWAUKEE, WI
(Shipping prepaid and added to invoice)
Orders normally shipped UPS
TERMS: Net 30, subject to credit approval.
WE ALSO ACCEPT CREDIT CARD ORDERS!
NOTE: Instructions, Wiring Diagrams (if applicable)
and Warranty included with all equipment shipped.
���� ���� ������ ������� ���������� ��� �����
������ ������������ ���� ������������ ������� �����������������
30
A small sampling of
Agilent Technologies
Allied Signal
Allen Bradley
American Airlines Flight Academy
American Express
Brookdale Hospital Medical Center
Boeing
Brookhaven National Lab.
Citibank, N.A.
Ford Motor Company
Federal Reserve Bank-Boston
General Motors
Great Lakes Data Center
Harrah's Hotels & Casinos
Hewlett Packard
Harris Semi-conductor
Indiana State Archives
International Paper
IBM
Intel
Johnson & Johnson
Lockheed Martin
Lucent Technologies
Motorola
Maine State Archives
Naval Weapons Support Center
New Hampshire - Vermont
Hospitalization Service
Ohio College Library
Pennsylvania Hospital
Puget Sound Naval Shipyard
Raytheon
users:
RR
Texaco
Texas Instruments
Smithsonian Institute
Sharp Electric
Sears Roebuck & Co.
Tampa Electric Co.
University of Michigan
US General Service Administration
University of Wisconsin
US Library of Congress
US Customs
USS Mississippi
Westinghouse
Vaco Products Co.
Quadgraphics
Youngstown Sheet & Tube
A small sampling of CEILING GUARD users:
R
Ball Memorial Hospital
Becton Dickinson
Borgess Medical Center
Boston Stock Exchange
Brethren Mutual Insurance Co.
Campbell County Hospital
Central Blood Bank of Pittsburgh
Cleveland Museum of Art
Data Scope Corporation
E.I. DuPont
E. J. Brach Corp.
Enterprise Bank
Fusion Digital
General Motors
Goshen Hospital
Honeywell
Interlink Communications
Lockheed Martin
Los Angeles Dept. of Airports
Marine Corp Logistics Base, GA
Medical Action Industries
Medtronic
Menard Inc.
Naval Research Lab
Naval Supply Depot, Guam
Naval Surface Weapons Center
Norpak Foods
NYC Health
Ontario Telephone
Pace University
Phelps County Med Ctr.
Pima County
Provident Mutual Insurance Co.
Rank Video of America
Searle Pharmaceutical
Siemens
St. Joseph's Hospital, Atlanta
U.S. Postal Service
University of Miami
University of Minnesota
US Department of Energy
US Department of State
Wisconsin Public Service Corp,
��� ������ ��������
���� ���� ������ ������� ���������� ��� �����
������ ������������ ���� ������������ ������� �����������������
���� �� ��� ���
WATER LEAK DETECTION SYSTEMS - SINCE 1975
WA-11