Black BLK-CCD223VS User manual

High Performance
Indoor/Outdoor Color CCTV
Dome Camera User Manual
Products: BLK-CCD203VS, BLK-CCD205VH, BLK-CPD206VH,
BLK-CCD223VS, BLK-CCD225VH, BLK-CPD226VH
Please read this manual before using your camera, and always follow the instructions
for safety and proper use. Save this manual for future reference.
BLK-DomeCameras_CM
3/18/11
!
WARNING

CAUTION
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the
equipment.
To prevent electric shock and risk of fire hazards:
Use a power source that is within specification only.
Do NOT expose this appliance to rain or moisture.
REGULATORY NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and use in
accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference, in which case the user will be
required to correct the interference at his own expense.
LEGAL NOTICE
DIGIOP products are designed to meet safety and performance standards with the use of specific DIGIOP
authorized accessories. DIGIOP disclaims liability associated with the use of non-DIGIOP authorized accessories.
The recording, transmission, or broadcast of any person’s voice without their consent or a court order is strictly
prohibited by law.
DIGIOP makes no representations concerning the legality of certain product applications such as the making,
transmission, or recording of video and/or audio signals of others without their knowledge and/or consent. We
encourage you to check and comply with all applicable local, state, and federal laws and regulations before
engaging in any form of surveillance or any transmission of radio frequencies.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks
and names or their products. DIGIOP, Inc. disclaims any proprietary interest in trademarks and trade names other
than its own.
No part of this document may be reproduced or distributed in any form or by any means without the express written
permission of DIGIOP, Inc.
© 2011 by DIGIOP, Inc. All Rights Reserved.
3850 Priority Way South Drive, Suite 200, Indianapolis, IN 46240
Sales/Support: 1.877.972.2522
ii
www.digiop.com
TABLE OF CONTENTS
Table of Contents
SECTION 1
SECTION 2
SECTION 3
SECTION 4
APPENDIX A
APPENDIX B
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Cameras with a vandalproof enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Cameras with a plastic enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 General Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Vandalproof camera mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Plastic camera mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4 Camera adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Software Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 LENS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 EXPOSURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 WHITE BALANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4 BACKLIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.5 DAY&NIGHT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.6 DPC (Dead Pixel Compensation). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.7 SPECIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Camera Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Camera with vandalproof housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Camera with plastic housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
High Performance CCTV Dome Camera User Manual
iii
PRECAUTIONS
Precautions
Do not install the camera in extreme temperature conditions. Use the camera in environments where temperature is
between 14°F and 122°F. Ensure adequate ventilation.
Do not install or use the camera in an environment where the humidity is high. It can degrade the image quality.
Do not install the camera under unstable lighting conditions. Severe lighting changes or flicker can cause the camera to
work improperly.
Never use the camera close to a gas or oil leak. These chemicals can damage the camera.
Do not drop the camera or subject it to physical shocks. These can cause malfunctions to occur.
Never point the camera at intense light. Smear or blooming may occur, and it can damage the CCD.
Do not expose an indoor camera to rain or spill liquids on it. If it gets wet, wipe it dry immediately. Liquids can contain
minerals that corrode electronic components.
Check the power source to ensure that it is within specifications before connecting it to the camera.
iv
www.digiop.com
SECTION 1: INTRODUCTION
SECTION 1
Introduction
DIGIOP Black high performance indoor/outdoor CCTV dome cameras feature a very high resolution Sony® CCD sensor providing 600
TVL, with a 2.8 – 11 mm lens, a digital wide dynamic range, dual voltage range support (24 VAC, 12 VDC), and on-screen display
(OSD) for control and setup. These cameras are available with or without an IR array, and in either a durable plastic or vandalproof
enclosure.
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Wall or ceiling mounting through 3-axis camera bracket
Safety strap keeps dome cover attached while making adjustments
1/3” Sony Super HAD CCD II: 410K pixels
High resolution 600 TV Lines
Day or day/night operation (ICR)
Vari-focal lens 2.8~11mm
Digital wide dynamic range
Digital noise reduction
Privacy mask function
On screen display (OSD)
Motion detection
Parking line
Backlight Compensation (BLC) and High Light Compensation (HLC)
IR Smart features
Lens
Focus Lever
Zoom Lever
Joystick /
OSD Control
Tilt/Pan
Bracket
Video Out
Internal Components - Cameras Without IR Array
High Performance CCTV Dome Camera User Manual
1
SECTION 1: INTRODUCTION
Lens
IR Array
Focus Lever
Joystick /
OSD Control
Zoom Lever
Video Out
Tilt/Pan
Bracket
Internal Components - Cameras With IR
1.1 Cameras with a vandalproof enclosure
Vandalproof cameras are IP67 rated and include a rugged die-cast aluminum enclosure. They are flush surface mountable using the
mount adaptor box supplied.
1.1.1 What’s in the box
Your camera includes the following:
•
•
•
•
•
•
•
2
Security tool
Machine screws (4)
Mounting cap
Mounting screws (4)
L-wrench
User manual
Dome bracket (optional)
www.digiop.com
SECTION 1: INTRODUCTION
What’s in the box
Optional dome bracket for wall and ceiling mounting
1.1.2 What you need
To install the camera you will need:
•
•
12 VDC or 24 VAC power source
Tools for mounting the camera
1.2 Cameras with a plastic enclosure
1.2.1 What’s in the box
Your camera includes the following:
High Performance CCTV Dome Camera User Manual
3
SECTION 1: INTRODUCTION
•
•
•
•
Mounting screws (4)
L-wrench
User manual
Dome bracket (optional)
What’s in the box
Optional dome bracket
4
www.digiop.com
SECTION 2: INSTALLATION
SECTION 2
Installation
2.1 General Guidelines
•
Outdoor installations: Use the rubber rings included with the machine screws (4) to ensure that the unit is sealed properly.
•
Dome/window care: Handle the dome carefully to prevent scratching. If a scratch appears over the lens, adjust the dome
window to move the scratch out of view.

CAUTION
Keep dome cover and camera lens clean. To avoid smearing, do not expose the camera lens to a strong light source such as the
sun or spot lights.
•
Monitor impedance: Set the monitor impedance switch to 75Ω.
•
Power supply: To avoid fire or shock hazard, use only a UL listed power supply.
•
Camera drop cable: The camera drop cable includes two connectors:
——
Power connector (black with green terminal adapter) – The connector is non-polarized. Use AC24V power source
(AC24V 1A adapter) or DC 12V power source (DC12V 1A adapter).
——
Video coax connector (BNC, yellow) – for transmission of the video signal across coax (75Ω) cable.
High Performance CCTV Dome Camera User Manual
5
SECTION 2: INSTALLATION
Power Connector
2.1.1 What you need
To install the camera you will need:
•
•
12 VDC or 24 VAC power source
Tools for mounting the camera
2.2 Vandalproof camera
mounting
The camera can be installed on a junction box or directly to a wall
or ceiling.
1.
Attach the surface mount bracket to the ceiling or wall
using four (4) mounting screws.
2.
Connect the dome base to the surface mount bracket using
the screws with rubber rings provided.
3.
Route the power and video cables to the camera location
and attach them to the camera drop cable (see General
guidelines above).
4.
Attach the dome base to the surface mount bracket using
the four machine screws provided.
6
www.digiop.com
Video Coax
Connector
SECTION 2: INSTALLATION
2.3 Plastic camera mounting
1.
Connect the dome base to the mounting surface using four
(4) screws.
2.
Route the power and video cables to the camera location
and attach them to the camera drop cable (see General
guidelines above).
2.4 Camera adjustments
1.
Attach a video setup monitor to the yellow RCA (EXTRA VIDEO OUT) connector inside the camera assembly, or setup a
remote monitor for viewing video from the camera.
2.
Power on the camera and video monitor.
3.
While observing video from the camera, adjust the pan/tilt swivel and PCB bracket to aim the camera in the preferred
direction.
High Performance CCTV Dome Camera User Manual
7
SECTION 2: INSTALLATION
Ceiling mounting
Wall mounting
4.
Adjust the image with the focus and zoom levers.
5.
Configure your camera using the software menus in the OSD. See Software Setup in the following section of this manual.
6.
Place the dome cover over the base and adjust the dome window. Tighten the captive screws that secure the cover to the
base.
7.
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
——
——

Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub the surface with
a soft cloth moistened with a mild detergent solution, then rinse and dry it with a soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing. These may cause
damage to the surface over time.
CAUTION
8
Do not use benzene, thinner or other chemical products on the camera assembly; these may dissolve the paint and
promote damage of the surfaces. Before using any chemical product, read the accompanying instructions carefully.
www.digiop.com
SECTION 3: SOFTWARE SETUP
SECTION 3
Software Setup
Use the SETUP joy stick on the OSD control panel to navigate through the menu system. Press the joy stick down (toward the PC
board) to enter the SETUP menu or select an entry, rock the stick up or down to highlight an item in the list, and left or right display
the option you want to select.
The SETUP menu consists of a list of sub-menus or displays the
option selected for a camera function. When sub-menus are
available, the  symbol is shown.
3.1 LENS
LENS: Select lens type: DC / VIDEO / MANUAL
3.2 EXPOSURE
SHUTTER: You can set the shutter to auto or manual mode. Options are: AUTO, 1/60 sec, FLK, 1/250 sec, 1/500 sec, 1/1000 sec,
1/2000 sec, 1/4000 sec, 1/5000 sec, 1/10000 sec, 1/100000 sec
BRIGHTNESS: You can adjust brightness level. 0 (dark) ~ 255 (bright) steps
AGC: You can select auto gain control level. OFF / LOW / MIDDLE / HIGH
High Performance CCTV Dome Camera User Manual
9
SECTION 3: SOFTWARE SETUP
DWDR: The DWDR feature employs intelligent light level control to compensate for strong backlight conditions. DWDR: OFF / ON
DWDR OFF
DWDR ON
3.3 WHITE BALANCE
WHITE BAL: You can select one of the following modes: ATW1 / ATW2 / AWC g SET / MANUAL (INDOOR / OUTDOOR / MANUAL)
——
——
——
——
——
——
——
——
10
ATW1: Automatically adjusts color according to the available lighting for temperature range: 2500°K to 9500°K.
ATW2: Automatically adjusts color according to the available lighting for temperature range: 2300°K to 10000°K.
AWC g SET: It is a fixed white balance mode that may be automatically readjusted only by pressing SET Button in
ONE PUSH mode.
OUTDOOR: Set color temperature for Outdoor light (5400°K)
INDOOR: Set color temperature for Indoor light (3200°K)
MANUAL: Color can be corrected when the user increases or decreases “Red Gain” or “Blue Gain”.
RED GAIN: Adjust R gain value 0 ~ 255
BLUE GAIN: Adjust B gain value 0 ~ 255
www.digiop.com
SECTION 3: SOFTWARE SETUP
3.4 BACKLIGHT
BACKLIGHT: Select OFF / BLC / HLC
BLC (Back Light Compensation)
——
——
——
——
——
——
——
AREA SEL: Select AREA1, AREA2
AREA STATE: Select OFF / ON
GAIN: Select 0 ~ 255 steps
HEIGHT: Select 0 ~ 15 steps
WIDTH: Select 0 ~ 15 steps
LEFT/RIGHT: Select 0 ~ 15 steps
TOP/BOTTOM: Select 0 ~ 15 steps
HLC (High Light Compensation)
——
——
LEVEL: Select 0 ~ 255 steps
MODE: ALL DAY, NIGHT ONLY
High Performance CCTV Dome Camera User Manual
11
SECTION 3: SOFTWARE SETUP
3.5 DAY&NIGHT
DAY&NIGHT: Select AUTO / COLOR / B/W / EXT ·
AUTO: Day&Night Auto mode
——
——
——
——
D -> N LEVEL: 182 ~ 192 steps
D -> N DELAY: 1 ~ 30 SEC
N -> D LEVEL: 0 ~ 10 steps
N -> D DELAY: 1 ~ 30 SEC
COLOR: Day&Night only color mode
B/W: Day&Night black and white (B/W) mode
——
——
BURST: OFF / ON
IR SMART: OFF / ON. This option controls the IR LED output level to compensate for object distance. The IR SMART
option is used for objects in an area of the image.
IR SMART OFF
12
www.digiop.com
IR SMART ON
SECTION 3: SOFTWARE SETUP
R GAIN: 0 ~ 255
HEIGHT: 0 ~ 15
WIDTH: 0 ~ 15
LEFT/RIGHT: 0 ~ 15
TOP/BOTTOM: 0 ~ 15
——
IR LEVEL: HIGH / LOW
EXT: Day&Night EXT mode
3.6 DPC (Dead Pixel Compensation)
Select DPC for dead pixel compensation processing. DPC can be set to OFF (default) or AUTO. When AUTO is used, the camera will
remove defective pixels from an image automatically.
3.7 SPECIAL
CAM TITLE: Select camera title menu (Text edit).
High Performance CCTV Dome Camera User Manual
13
SECTION 3: SOFTWARE SETUP
MOTION: Select camera title menu (Text edit)
——
——
——
——
——
——
——
——
AREA SEL: Select AREA1, AREA2, AREA3, AREA4
AREA STATE: Select OFF / ON
HEIGHT: Select 0 ~ 15 steps
WIDTH: Select 0 ~ 15 steps
LEFT/RIGHT: Select 0 ~ 15 steps
TOP/BOTTOM: Select 0 ~ 15 steps
DEGREE: Select 0 ~ 255 steps
VIEW: OFF / ON
PRIVACY: You can cover an area of the screen.
——
——
——
——
——
——
——
AREA SEL: Select AREA1, AREA2, AREA3, AREA4
AREA STATE: Select OFF / ON
HEIGHT: Select 0 ~ 255 steps
WIDTH: Select 0 ~ 255 steps
LEFT/RIGHT: Select 0 ~ 255 steps
TOP/BOTTOM: Select 0 ~ 255 steps
COLOR: Select 0 ~ 15 steps
PARK.LINE: You can insert a line on the screen. This feature may be useful when aligning the camera image with objects in the
field of view.
——
——
——
——
——
——
14
LT: You can adjust the top left area on screen. (0 ~ 195 steps)
LB: You can adjust the bottom left area on screen. (0 ~ 194 steps)
RT: You can adjust the top right area on screen. (0 ~ 194 steps)
RB: You can adjust the bottom right area on screen. (0 ~ 194 steps)
F: You can adjust the front area on screen. (0 ~ 68 steps)
N: You can adjust the near area on screen. (0 ~ 68 steps)
www.digiop.com
SECTION 3: SOFTWARE SETUP
——
T: You can adjust the parking line thickness. (0 ~ 15 steps)
IMAGE ADJ.: You can adjust camera image.
——
——
——
LENS SHAD: LEVEL: 0 ~ 255 steps
2DNR: (on-screen Digital Noise Reduction) (OFF/ON)
MIRROR: (reverse the camera image horizontally) (OFF/ON)
MIRROR OFF
——
——
——
——
MIRROR ON
FONT COLOR:
FONT: 16 colors (O ~ 15 steps)
ID & TITLE: O ~ 15 steps
CONTRAST: You can adjust contrast on screen. (0 ~ 255 steps)
SHARPNESS: You can adjust camera image for clarity. (0 ~ 31 steps)
DISPLAY: You can adjust camera output for the display type. (CRT / LCD / USER)
CRT (Cathode Ray Tube, Braun tube). PED LEVEL: 0 ~ 63 steps, COLOR GAIN: 0 ~ 255
steps
LCD (Liquid Crystal Display)
GAMMA: 0.05 ~ 1.00 steps
PED LEVEL: 0 ~ 63 steps
COLOR GAIN: 0 ~ 255 steps
High Performance CCTV Dome Camera User Manual
15
SECTION 3: SOFTWARE SETUP
——
USER
GAMMA: 0.05 ~ 1.00 steps
PED LEVEL: 0 ~ 63 steps
COLOR GAIN: 0 ~ 255 steps
NEG.IMAGE: You can invert a color image, or a black and white image. (OFF/ON)
COMM ADJ.:
——
——
——
——
——
CAM ID: Select the camera ID. 1 ~ 255
BAUD RATE: Select serial communication speed: 2400 / 4800 / 9600 / 19200 / 38400 / 57600 bps
PROTOCOL: Select operating protocol. PELCO-D / PELCO-P
DISPLAY ID: Select display item. OFF/ON
ID POS: You can adjust ID position on screen.
LANGUAGE: You can select language. ENGLISH / CHINESE
VERSION: Factory vision.
RESET: Set the camera options to the factory default settings.
16
www.digiop.com
SECTION 4: SPECIFICATIONS
SECTION 4
Specifications
Table 1.Model Differences
Indoor
Outdoor
TDN
IR
BLK-CCD203VS
BLK-CCD223VS
--
--
BLK-CCD205VH
BLK-CCD225VH
√
--
BLK-CPD206VH
BLK-CPD226VH
√
√
TDN: True Day & Night, uses an IR cut filter instead of switching the image to black and white.
IR: Built-in infrared LED array
Table 2.Component Specifications
Component
Value
Image Sensor
1/3" SONY Super HAD CCD II
Total Pixels
811(H) × 508(V)
Scanning system
2:1 interlace
Scanning frequency
15.734KHz(H), 59.94Hz(V)
Sync system
Internal
Resolution
Max 600 TV lines in color, 650 TV lines in B/W
Min. Illumination
Color: 0.3 lux , BW: 0.1 lux (0 lux @ IR_LED on)
Video output
1.0 Vp-p (75 ohm, composite)
S/N ratio
> 50dB (AGC off)
Exposure
Shutter/Brightness/AGC/DWDR
Lens
DC / VIDEO / MANUAL
Gain control
Off / Low / Middle / High
Shutter speed
1/60 ~ 1/100,000 sec
DWDR
Off / On (0 ~ 35 steps)
Flickerless
Off / On
Brightness
0 ~ 255 steps
White balance
ATW1 / ATW2 / AWC / Outdoor / Indoor / Manual
BLC
Off / BLC / HLC
BLC
Area / gain selectable
High Performance CCTV Dome Camera User Manual
17
SECTION 4: SPECIFICATIONS
Component
Value
HLC
All Day / Night / (0~255 steps)
Day&Night
Auto / Color / BW / Ext
Auto
Level / Delay selectable
BW
Burst off/on / IR Smart off/on (Gain/level selectable)
DPC
Dead Pixels Compensation
Special
Title / MD / PM / Parking / Image / Comm / Language / Version
Cam Title
Text edit
Motion
Off / On (4 position)
Privacy
Off / On (8 position)
Park. Line
Off / On (variable size)
Language
English / Chinese
Image ADJ
Lens Shad / DNR / Mirror / Font color / Contrast / Sharpness / Display / Neg. Image
Lens Shading
Off / On (0~255 steps)
DNR
Off / On
Mirror
Off /On
Font Color
ID & Title / OSD font color selectable
Contrast
0~255 steps
Sharpness
0~31 steps
Display
CRT / LCD / User
Negative Image
Off / On
Power Source
AC24V / DC12V
Power Consumption
100mA
Power Input
Connector
Video Output
Connector
Operating Temperature
+14°F ~ +122°F (-10°C ~ +50°C)
Operating Humidity
0 ~ 86% (non-condensing)
Storage Temperature
-4°F ~ +140°F (-20°C ~ +60°C)
18
www.digiop.com
APPENDIX A: TROUBLESHOOTING
APPENDIX A
Troubleshooting
Problem
Solution
Nothing appears on the screen.
- Check the power connections.
- Check the video cable connections.
- Ensure that the lens mode is set to DC (VIDEO).
The video image is not clear.
- Clean the lens with a soft, clean cloth.
- Adjust the monitor screen for room lighting conditions.
- Move the camera if necessary.
The screen is dark.
- Adjust the contrast feature of the monitor.
- If you have an intermediate device, set the 75Ω /Hi-Z properly, and check the terminals.
The MOTION DETECTION function is not working
- Is “MOTION DETECTION” mode turned on?
- Is the MD Sensitivity set too low? Increase the sensitivity.
- Check the setting of the MD AREA.
The WDR function is not working
- Is the WDR level too low?
- Is the AE Mode set to MANUAL? WDR is disabled in MANUAL exposure mode.
Colors are not quite right.
- Is the camera facing directly into sunlight or fluorescent light?
- Is the auto iris lens is being used?
- Check the connection of the lens connector cable.
The Day&Night function doesn’t work.
- Is the AGC (EXPOSURE menu) set to OFF? The Auto Day&Night Function doesn’t work if the AGC is OFF.
High Performance CCTV Dome Camera User Manual
19
APPENDIX B: CAMERA DIMENSIONS
APPENDIX B
Camera Dimensions
2.95"
4.96"
1.38"
1.61"
Camera with vandalproof housing
2.95"
1.52"
1.75"
1.81"
2.09"
Camera with plastic housing
3.29"
20
www.digiop.com