RedMax BC225DL Specifications

T3108-93110(012)
OWNER / OPERATOR MANUAL
BRUSHCUTTERS
BC225DL
WARNING
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Before using our products, please
read this manual carefully to
understand the proper use of your
unit.
APPLICABLE SERIAL NUMBERS :
DRIVE UNIT 000101 and up
ENGINE UNIT 000101 and up
SAFETY FIRST
Instructions contained in warnings within this
manual marked with a
symbol concern
critical points which must be taken into
consideration to prevent possible serious
bodily injury, and for this reason you are
requested to read all such instructions
carefully and follow them without fail.
■ WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions which must be
followed in order to prevent accidents which could
lead to serious bodily injury or death.
IMPORTANT
This mark indicates instructions which must be
followed, or it leads to mechanical failure,
breakdown, or damage.
NOTE
This mark indicates hints or directions useful in the
use of the product.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
CONTENTS
Parts location …………………………………4
Specifications …………………………………4
Warning labels on the machine ……………5
Symbols on the machine ……………………6
For safe operation ……………………………7
Set up …………………………………………13
Fuel……………………………………………15
Operation ……………………………………17
Maintenance …………………………………20
Storage ………………………………………24
Optional blade usage ………………………25
Troubleshooting guide ………………………30
Parts list ………………………………………31
1. Parts location
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Loop handle
Ignition switch
Throttle cable
Throttle lever
Drive shaft housing
Debris guard
Cutting line head
Gear case
Spark arrester
Starter knob
Fuel tank
Primer pump
Choke lever
Air cleaner cover
2. Specifications
■ BC225DL
Overall size(LxWxH)······················································ 70.8(1800)x12.8(325)x13.0(330) in(mm)
Dry weight w/o acc.······························································································· 10.0 lbs (5.0kg)
Engine Type······················································································ Air-cooled 2-stroke gasoline
Model ········································································································ Zenoah G24LS
Displacement ······················································································· 1.4cu-in (22.5cm3)
Max. output························································································ 1.08Hp at 8000 rpm
Fuel ······················································································· Mixture(Gasoline 50 : Oil 1)
Carburetor ··················································································· Walbro Diaphragm type
Spark plug ···························································································· Champion RCJ6Y
Fuel tank capacity································································································ 20.3 fl.oz (0.6 )
Transmission··········································································· Centrifugal clutch, Rigid driveshaft
Reduction ratio ····················································································································· 1.462
Cutting head rotating direction ················································ Counter-clockwise(Operator view)
Durability period··················································································································300hrs.
Standard Accessories
4 in. 2-line Head ········································································································ 1 pc.
Goggle ······················································································································· 1 pc.
Specifications are subject to change without notice.
❲4 ❳
3. Warning labels on the machine
(1) Read owner's manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Warning/Attention
(4) Keep all children, bystanders and helpers 15 meters away from the brushcutter
IMPORTANT
If warning label peel off or become soiled and impossible to read, you should contact the dealer
from which you purchased the product to order new labels and affix them in the required
location(s).
WARNING
Never modify your brushcutter.
We won't warrant the machine, if you use the remodeled brushcutter or you don't observe
the proper usage written in the manual.
❲5 ❳
4. Symbols on the machine
For safe operation and maintenance,
symbols are carved in relief on the machine.
According to these indications, please be
careful not to make a mistake.
(a) The port to refuel the "MIX GASOLINE"
Position: FUEL TANK CAP
(b) The direction to close the choke
Position: AIR CLEANER COVER
(c) The direction to open the choke
Position: AIR CLEANER COVER
IMPORTANT ENGINE INFORMATION
THIS ENGINE MEETS U.S. EPA PH1 AND
2001 CALIFORNIA EMISSION REGULATIONS
FOR SMALL OFF-ROAD ENGINES WITH AN
EMISSION DURABILITY PERIOD OF 300 HOURS.
ENGINE FAMILY : 1KZXS. 0254CD
ENGINE DISPLACEMENT : 22.5cc
REFER TO OWNER'S MANUMAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
MANUFACTURED
RedMax
❲6 ❳
Made in Japan
INFORMATION IMPORTANTE CONCERNANT LE MOTEUR
Ce moteur est conformc aux normcs U.S. EPA PH1 et 2001 ainsi
qu’aux autres dispositions ultérieures de la réglementation
concernant la pollution de l’air pour les petits moteurs tout-terrain
avec une période de durabilité opour les émissions de 300 heures.
Type de moteur : 1KZXS. 0254CD
Cylindrée du moteur : 22,5cc
Se référer au Manuel de l’utilisateur pour les spécifications
d’entretien et les réglages.
Manufacturé
RedMax
Made in Japan
5. For safe operation
1. Read this manual carefully until you
completely understand and follow all safety
and operating instructions.
2. Keep this manual handy so that you may refer
to it later whenever any questions arise. Also
note, if you have any questions which cannot
be answered herein, contact the dealer from
whom you purchased the product.
3. Always be sure to include this manual when
selling, lending, or otherwise transferring the
ownership of this product.
4. Never allow children or anyone unable to fully
understand the directions given in the manual
to use the machine.
■ WORKING CONDITION
1. When using the product, you should wear proper
clothing and protective equipment.
(1) Helmet
(2) Ear protectors
(3) Protection goggles or face protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools and files
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working area (rope,
warning signs)
(5) Whistle (for collaboration or emergency)
(6) Hatchet or saw (for removal of obstacles)
3. Do not wear loose clothing, jewelry, short
trousers, sandals, or go barefoot. Do not wear
anything which might be caught by a moving
part of the unit. Secure hair so it is above
shoulder length.
■ WORKING CIRCUMSTANCE
1. Never start the engine inside a closed room or
building. Exhaust gases contain dangerous
carbon monoxide.
2. Never use the product,
a. when the ground is slippery or when you can’t
maintain a steady posture.
❲7 ❳
5. For safe operation
b. At night, at times of heavy fog, or at any other
times when your field of vision might be
limited and it would be difficult to gain a clear
view of the working area.
c. During rain storms, during lightning storms, at
times of strong or gale-force winds, or at any
other times when weather conditions might
make it unsafe to use the product.
■ WORKING PLAN
1. You should never use the product when under
the influence of alcohol, when suffering from
exhaustion or lack of sleep, when suffering from
drowsiness as a result of having taken cold
medicine or at any other time when a possibility
exists that your judgment might be impaired or
that you might not be able to operate the product
properly and in a safe manner.
2. When planning your work schedule, allow plenty
of time to rest. Limit the amount of time over
which the product is to be used continuously to
somewhere around 30~40 minutes per session,
and take 10~20 minutes of rest between work
sessions. Also try to keep the total amount of
work performed in a single day under 2 hours or
less.
WARNING
1. If you don’t observe the working time, or
working manner (See ■ USING THE
PRODUCT), Repetitive Stress Injury(RSI)
could occur.
If you feel discomfort, redness and swelling
of your fingers or any other part of your
body, see a doctor before getting worse.
2. To avoid noise complaints, in general,
operate product between 8a.m. and 5p.m. on
weekdays and 9a.m. to 5p.m. weekends.
NOTE
Check and follow the local regulations as to sound
level and hours of operations for the product.
❲8 ❳
5. For safe operation
■ BEFORE STARTING THE ENGINE
1. The area within a perimeter of 50 feet (15m) of
the person using the product should be
considered a hazardous area into which no one
should enter. If necessary yellow warning rope,
warning signs should be placed around the
perimeter of the area. When work is to be
performed simultaneously by two or more
persons, care should also be taken to constantly
look around or otherwise check for the presence
and locations of other people working so as to
maintain a distance between each person
sufficient to ensure safety.
2. Check the condition of working area to avoid any
accident by hitting hidden obstacles such as
stumps, stones, cans, or broken grass.
IMPORTANT
Remove any obstacle before beginning work.
3. Inspect the entire unit for loose fasteners and
fuel leakage. Make sure that the cutting
attachment is properly installed and securely
fastened.
4. Be sure the debris guard is firmly attached in
place.
5. If the cutting head is the metal blade, use the
shoulder strap. Adjust the strap for comfort
before starting the engine. The strap should be
adjusted so the left hand can comfortably hold
the handlebar grip approximately waist high.
■ STARTING THE ENGINE
1. Keep bystanders and animals at least 50feet
(15m) away from the operating point. If you are
approached, immediately stop the engine.
2. The product is equipped with a centrifugal clutch
mechanism, so the cutting attachment begins to
rotate as soon as the engine is started by putting
the throttle into the start position. When starting
the engine, place the product onto the ground in
a flat clear area and hold it firmly in place so as
to ensure that neither the cutting part nor the
throttle come into contact with any obstacle
when the engine starts.
❲9 ❳
5. For safe operation
WARNING
Never place the throttle into the high speed
position when starting the engine.
3. After starting the engine, check to make sure
that the cutting attachment stops rotating when
the throttle is moved fully back to its original
position. If it continues to rotate even after the
throttle has been moved fully back, turn off the
engine and take the unit to your authorized Red
Max servicing dealer for repair.
■ USING THE PRODUCT
IMPORTANT
Cut only materials recommended by the
manufacturer. And use only for tasks explained
in the manual.
1. Grip the handles firmly with both hands using
your whole hand. Place your feet slightly apart
(slightly further apart than the width of your
shoulders) so that your weight is distributed
evenly across both legs, and always be sure to
maintain a steady, even posture while working.
2. Keep cutting attachment below waist level.
3. Maintain the speed of the engine at the level
required to perform cutting work, and never raise
the speed of the engine above the level
necessary.
4. If the unit start to shake or vibrate, turn off the
engine and check the whole unit. Do not use it
until the trouble has been properly corrected.
5. Keep all parts of your body away from rotating
cutting attachment and hot surfaces.
6. Never touch the muffler, spark plug, or other
metallic parts of the engine while the engine is in
operation or immediately after shutting down the
engine. Doing so could result in serious burns or
electrical shock.
❲ 10 ❳
5. For safe operation
• IF SOMEONE COMES
1. Guard against hazardous situations at all times.
Warn adults to keep pets and children away
from the area. Be careful if you are approached.
Injury may result from flying debris.
2. If someone calls out or otherwise interrupts you
while working, always be sure to turn off the
engine before turning around.
■ MAINTENANCE
1. In order to maintain your product in proper
working order, perform the maintenance and
checking operations described in the manual at
regular intervals.
2. Always be sure to turn off the engine before
performing any maintenance or checking
procedures.
WARNING
The metallic parts reach high temperatures
immediately after stopping the engine.
3. When replacing the cutting attachment or any
other part, or when replacing the oil or any
lubricant, always be sure to use only RedMax
products or products which have been
certified by RedMax for use with the RedMax
product.
4. In the event that any part must be replaced or
any maintenance or repair work not described in
this manual must be performed, please contact a
representative from the store nearest RedMax
authorized servicing dealer for assistance.
5. Do not use any accessory or attachment other
than those bearing the RedMax mark and
recommended for the unit.
6. Under no circumstances should you ever take
apart the product or alter it in any way. Doing so
might result in the product becoming damaged
during operation or the product becoming unable
to operate properly.
■ HANDLING FUEL
1. The engine of the RedMax product is designed
to run on a mixed fuel which contains highly
flammable gasoline. Never store cans of fuel or
❲ 11 ❳
5. For safe operation
2.
3.
4.
5.
refill the tank of the unit in any place where there
is a boiler, stove, wood fire, electrical sparks,
welding sparks, or any other source of heat or
fire which might ignite the fuel.
Never smoke while operating the unit or refilling
its fuel tank.
When refilling the tank, always turn off the
engine and allow it to cool down. Take a careful
look around to make sure that there are no
sparks or open flames anywhere nearby before
refueling.
Wipe spilled fuel completely using a dry rag if
any fuel spillage occurs during refueling.
After refueling, screw the fuel cap back tightly
onto the fuel tank and then carry the unit to a
spot 10feet (3m) or more away from where it
was refueled before turning on the engine.
■ TRANSPORTATION
1. When hand-carrying the product, cover over the
cutting part if necessary, lift up the product and
carry it paying attention to the blade.
2. Never transport the product over rough roads
over long distances by vehicle without removing
all fuel from the fuel tank. If doing so, fuel might
leak from the tank during transport.
❲ 12 ❳
6. Set up
SE1
SE2
■ MOUNTING ENGINE (SE1)
1. Loosen the bolts temporarily attached to the
clutch housing.
2. Push the driveshaft toward the gearcase and
rotate it by hand to check that the driveshaft is
engaged with the gears.
3. Insert the shaft tube into the clutch housing until
it bottoms. When difficult to engage, twist the
engine slightly.
4. Align the positioning holes on the clutch housing
and the shaft tube and fit the bolt into the holes.
And fasten the tightning bolts by turns securely.
(Tightning torque: 4.9~7.8 N.m. (0.5~0.8kg·m))
(1) Positioning hole
(2) Bolt (M5x10)
(3) Tightning bolt (M5x22)
SE3
■ INSTALLING HANDLE (SE2)
• Mount the handle to the shaft tube and clamp it
at your best operating position.
■ INSTALLING DEBRIS GUARD (SE3)
• Put the debris guard on the shaft tube near the
gear box, attach it with the 2 screws and
hardware provided.
SE4
■ CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover. (SE4)
SE5
2. Connect the end of the throttle wire to the joint
on the top of the carburetor. (SE5)
■ CONNECTING SWITCH WIRES
• Connect the switch wires between the engine
and the main unit. Pair the wires of the same
color.
❲ 13 ❳
6. Set up
SE6
■ INSTALLING CUTTING HEAD (SE6)
1. While locking the gear shaft by inserting the
attached bar into the upper holder and the gear
box, loosen and remove the hexagon bolt(lefthanded)
2. Fit the spacer attached to the head assembly
between the upper and lower holders. Then
screw in the cutting head to the gear shaft over
the holders. Hand-tighten it securely.
(1) Spacer
❲ 14 ❳
7. Fuel
WARNING
• Gasoline is very flammable. Avoid smoking
or bringing any flame or sparks near fuel.
Make sure to stop the engine and allow it
cool before refueling the unit. Select outdoor
bare ground for fueling and move at least
3m(10ft) away from the fueling point before
starting the engine.
• The RedMax engines are lubricated by oil
specially formulated for air-cooled 2-cycle
gasoline engine use. If RedMax oil is not
available, use an anti-oxidant added quality oil
expressly labeled for air-cooled 2-cycle engine
use. (JASO FC GRADE OIL or ISO EGC
GRADE)
50:1 MIXING CHART
GASOLINE gal. 1
2
3
4
5
2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13
GASOLINE liter
2-CYCLE OIL ml
1
20
2
40
3
60
4
80
5
100
RECOMMENDED MIXING RATIO
GASOLINE 50:OIL 1
• Exhaust emission are controlled by the
fundamental engine parameters and
components(eq., carburation, ignition timing
and port timing) without addition of any
major hardware or the introduction of an
inert material during combustion.
• These engines are certified to operate on
unleaded gasoline.
• Make sure to use gasoline with a minimum
octane number of 90 ROZ(USA/Canada : pump
octane min.87)
• Unleaded gasoline is recommended to reduce
the contamination of the air for the sake of your
health and the environment.
• Poor quality gasolines or oils may damage
sealing rings, fuel lines or fuel tank of the
engine.
■ HOW TO MIX FUEL
1. Measure out the quantities of gasoline and oil to
be mixed.
2. Put some of the gasoline into a clean, approved
fuel container.
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate again for
❲ 15 ❳
7. Fuel
at least one minute.
5. Put a clear indication on the outside of the
container to avoid mixing up with gasoline or
other containers.
6. Indicate the contents on outside of container for
easy identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap
on a dustless place.
2. Put fuel into the fuel tank to 80% of the full
capacity.
3. Fasten the fuel cap securely and wipe up any
fuel spillage around the unit.
WARNING
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away from
the fueling point before starting the engine.
3. Stop the engine before refueling the unit.
FOR YOUR ENGINE LIFE, AVOID;
1. FUEL WITH NO OIL(RAW GASOLINE) – It will
cause severe damage to the internal engine
parts very quickly.
2. GASOHOL – It can cause deterioration of rubber
and/or plastic parts and disruption of engine
lubrication.
3. OIL FOR 4-CYCLE ENGINE USE or WATER
COOLED 2-CYCLE ENGINE USE – It can
cause spark plug fouling, exhaust port blocking,
or piston ring sticking.
4. Mixed fuels which have been left unused for
a period of one month or more may clog the
carburetor and result in the engine failing to
operate properly.
❲ 16 ❳
8. Operation
OP1
OP2
■ STARTING ENGINE
1. Rest the unit on a flat, firm place. Keep the
cutting head off the ground and clear of
surrounding objects as it will start rotating upon
starting of the engine.
2. Pump the primer until fuel flows out in the clear
tube. (OP1)
3. Move the choke lever upward to close the
choke. (OP2)
(1) Choke lever
(2) Close
(3) Open
4. Shift the ignition switch to the START position.
(OP3)
OP3
(1) Ignition switch
(2) Stop
(3) Start
5. While pulling the throttle lever with the little
finger of your left hand, pull the starter rope.
(OP4)
NOTE
OP4
• Avoid pulling the rope to its end or returning it by
releasing the knob. Such actions can cause
starter failures.
6. When the engine has started, move the choke
lever gradually downward to open the choke.
7. Allow the engine to warm up for a half minute
before starting operation.
NOTE
1. When restarting the engine immediately after
stopping it, leave the choke open.
2. Overchoking can make the engine hard to start
due to excess fuel. When the engine failed to
start after several attempts, open the choke and
repeat pulling the rope, or remove the spark plug
and dry it.
❲ 17 ❳
8. Operation
■ STOPPING ENGINE
1. Release the throttle lever and run the engine for
a half minute.
2. Shift the ignition switch to the STOP position.
NOTE
• Except for an emergency, avoid stopping the
engine while pulling the throttle lever.
OP5
■ ADJUSTING IDLING SPEED (OP5)
1. When the engine tends stop frequently at idling
mode, turn the adjusting screw clockwise.
2. When the cutting head keeps rotating after
releasing the trigger, turn the adjusting screw
counter-clockwise.
(1) Idle adjustment screw
(2) Cable adjuster
NOTE
• Warm up the engine before adjusting the idling
speed.
■ LINE HEAD USAGE
WARNING
1. Always wear eye protection such as safety
goggles. Never lean over the rotating cutting
head. Rocks or other debris could be thrown
into eyes and face and cause serious
personal injury.
2. Keep the debris guard attached in place at all
times when the unit is operated.
TRIMMING GRASS AND WEEDS
• Always remember that the TIP of the line does
cutting. You will achieve better results by not
crowding the line into the cutting area. Allow the
unit to trim at its own pace.
1. Hold the unit so the head is off the ground and is
tilted about 20 degrees toward the sweep
direction.
2. Use full throttle when cutting.
❲ 18 ❳
8. Operation
3. You can avoid thrown debris by sweeping from
your left to the right.
4. Use a slow, deliberate action to cut heavy
growth. The rate of cutting motion will depend on
the material being cut. Heavy growth will require
slower action than will light growth.
5. Never swing the unit so hard as you are in
danger of losing your balance or control of the
unit.
6. Try to control the cutting motion with the hip
rather than placing the full workload on the arm
and hands.
7. Take precautions to avoid wire, grass and dead,
dry, long-stem weeds from wrapping around the
head shaft. Such materials can stall the head
and cause the clutch to slip, resulting in damage
to the clutch system if repeated frequently.
ADJUSTING THE LINE LENGTH
• Your brushcutters is equipped with a semi- auto
type nylon line head that allows the operator to
advance the line without stopping the engine.
When the line becomes short, lightly tap the
head on the ground while running the engine at
full throttle.
• Each time the head is bumped, the line advance
about 1 inch(25.4 mm). For better effect, tap the
head on bear ground or hard soil. Avoid
bumping in thick, tall grass as the engine may
stall by overload.
❲ 19 ❳
9. Maintenance
WARNING
MA1
MA2
• Always be sure to stop the engine before
inspecting the brushcutter for problems or
performing maintenance.
• Never alter the brushcutter or take the engine
apart.
• When replacing parts, always be sure to use
only RedMax products or products which
have been certified by RedMax for use with
the RedMax brushcutter.
• Things to check before using brushcutter.
■ REFILLING TRIMMING LINE
1. For replacement line, use a diameter of .095
in(2.4 mm). The spool is capable for a line upto
27 ft(8 m)on the 4” head, and 46 ft(14m)on the 6”
head. Avoid using a larger line as it may cut
down the trimming performance. For safety
reasons, do not use metalreinforced line.
2. Pinch the slotted area on the both sides of the
spool housing to unhook the bottom cap. (MA1)
MA3
3. Take out the spool and pull off the old line. Put
one end of new line through the spool holes and
pull it until the length is equal between each part
of the line. (MA2)
4. Wind up the line in the correct as indicated on
the spool. (MA3)
MA4
5. Hook each end of the line in the slot on the edge
of the spool, and then put the ends through the
eyelets on the housing. Make sure that the
spring and the washers are in place. (MA4)
6. While holding the spool against the housing, pull
the line ends to release them from the slot.
7. Line up the slot on the bottom cap with the hook
on the housing, press the cap against the
housing until it clicks.
❲ 20 ❳
9. Maintenance
WARNING
• Make sure that the engine has stopped and is
cool before performing any service to the
brushcutter. Contact with moving cutting
head or hot muffler may result in a personal
injury.
MA5
■ AIR FILTER
• The air filter, if clogged, will reduce the engine
performance. Monthly check and clean the filter
element in warm, soapy water as required. Dry
completely before installing. If the element is
broken or shrunk, replace with a new one. (MA5)
MA6
MA7
■ FUEL FILTER
• When the engine runs short of fuel supply, check
the fuel cap and the fuel filter for blockage.
(MA6)
■ SPARK PLUG
• Starting failure and mis-firing are often caused
by a fouled spark plug. Periodically clean the
spark plug and check that the spark gap is in the
correct range. For a replacement plug, use the
correct type specified by RedMax(See SPECIFICATIONS on the page 4). (MA7)
• REPLACEMENT PLUG IS A CHAMPION
RCJ6Y OR THE EQUIVALENT, SUCH AS
BOSCH WSR8E OR NGK BPMR7A.
IMPORTANT
• Note that using any spark plugs other than those
designated may result in the engine failing to
operate properly or in the engine becoming
overheated and damaged.
• To install the spark plug, first turn the plug until it
is finger tight, then tighten it a quarter turn more
with a socket wrench.
❲ 21 ❳
9. Maintenance
■ MUFFLER
WARNING
• Inspect periodically, the muffler for loose
fasteners, any damage or corrosion. If any
sign of exhaust leakage is found, do not use
the brushcutter and have it repaired
immediately.
• Note that failing to do so may result in the
engine catching on fire.
MA8
MA9
■ SPARK ARRESTER
• The muffler is equipped with a spark arrester to
prevent red hot carbon from flying out of the
exhaust outlet. Periodically inspect and clean as
necessary with a wire brush. In the State of
California it is required by law (Section 4442 of
the California Public Resources Code) to equip a
spark arrester when a gas powered tool is used
in any forest covered, brush covered, or grass
covered unimproved land. (MA8)
■ GEAR CASE
• The reduction gears are lubricated by
multipurpose, lithium-based grease in the gear
case. Supply new grease every 50 hours of use
or more often depending on the job condition.
• Remove the cutter holders before installing new
grease to arrange for old grease to exit. (MA9)
■ INTAKE AIR COOLING VENT
WARNING
• Never touch the cylinder, muffler, or spark
plugs with your bare hands immediately after
stopping the engine. The engine can
become very hot when in operation, and
doing so could result in severe burns.
• When checking the brushcutter to make sure
that it is okay before using it, check the area
around the muffler and remove any wood
chips or leaves which have attached
themselves to the brushcutter. Note that
failing to do so could cause the muffler to
❲ 22 ❳
9. Maintenance
become overheated, and that this in turn
could cause the brushcutter to catch on fire.
Always make sure that the muffler is clean
and free of wood chips, leaves, and other
waste before use.
• Check the intake air cooling vent and the area
around the cylinder cooling fins after every 25
hours of use for blockage, and remove any
waste which has attached itself to the
brushcutter. Note that it is necessary to remove
the plug guard shown in Figure 20 in order to be
able to view the upper part of the cylinder.
IMPORTANT
MA10
• If waste gets stuck and causes blockage around
the intake air cooling vent or between the
cylinder fins, it may cause the engine to
overheat, and that in turn may cause mechanical
failure on the part of the brushcutter. (MA10)
(1) Cylinder fin
(2) Intake air cooling vent (back)
MA11
■ PROCEDURES TO BE PERFORMED AFTER
EVERY 100 HOURS OF USE
1. Remove the muffler, insert a screwdriver into the
vent, and wipe away any carbon buildup. Wipe
away any carbon buildup on the muffler exhaust
vent at the same time. (MA11)
(1) Screwdriver
(2) Muffler
2. Tighten all screws, bolts, and fittings.
3. Check to see if any oil or grease has worked its
way in between the clutch lining and drum, and if
it has wipe it away using oil-free, lead-free
gasoline.
❲ 23 ❳
10. Storage
• Aged fuel is one of major causes of engine
starting failure. Before storing the unit, empty the
fuel tank and run the engine until it uses all the
fuel left in the fuel line and the carburetor. Store
the unit indoor taking necessary measures for
rust prevention.
❲ 24 ❳
11. Optional blade usage
OPT1
CUTTER
APPLICATION
CHART
9” 22-tooth:
SST229
9” 24-tooth:
SST249
8” 8-tooth:
SGB088
9” 8-tooth:
SGB089
8” 4-tooth:
SGB048
9” 4-tooth:
SGB049
Nylon line
head
Under
growth
Heavy
weeds
Light
weeds
Grass
■ CHOOSE THE BLADE
Choose a suitable recommended cutting
attachment according to the object to be cut.
(OPT1)
• When replacing blade always be sure to use
products which have been certified by RedMax.
OPT2
WARNING
• When using the metal blade, make sure to
install the hanger and the shoulder strap.
OPT3
■ SET UP THE HANGER (OPT2, 3)
1. Loosen the screws and remove the guard.
2. Loosen the screws and remove the gearcase.
3. Loosen the screws and take the loop handle off.
4. Install the hanger complete from the blade side
end and fix it with the screw.
5. Reinstall the gearcase.
(1) Hanger complete: 6420-17400
(2) Shoulder strap: T3002-17200
❲ 25 ❳
11. Optional blade usage
WARNING
• When sharpening, removing, or reattaching
the blade, be sure to wear thick, sturdy
gloves and use only proper tools and
equipment to prevent injury.
OPT4
(1)
(2)
OPT5
■ SET UP THE BLADE
1. Detach the line head assembly and the shaft
completely. (OPT4)
2. Put on the blade, making the marked side face
the holder, put the holder and the cover on, and
fasten the blade with the bolt and washer.
(OPT4)
(1) Cover: 6420-13280
(2) Holder: 6019-13250 (Holder, bolt, washer
are come with the unit)
IMPORTANT
Change the loop handle to the J-handle for safe
operation. (OPT5)
(1) Bracket: 3583-14101
(2) J-handle: 6367-14200
OPT6
■ BALANCE UNIT
1. Put on strap and attach unit to strap.
2. Slide clamp up or down until unit balances with
head just touching on the ground. (OPT6)
■ STARTING THE ENGINE
Please refer 5.For safe operation (P.9~10),
8.Operation (P.17).
WARNING
OPT7
❲ 26 ❳
• The product is equipped with a centrifugal
clutch mechanism, so the cutting attachment
begins to rotate as soon as the engine is
started by putting the throttle into the start
position. When starting the engine, place the
product onto the ground in a flat clear area
and hold it firmly in place so as to ensure
that neither the cutting part nor the throttle
come into contact with any obstacle when
the engine starts. (OPT7)
11. Optional blade usage
OPT8
■ CUTTING METHOD
a) Use the front left side cutting.
b) Guide the blade from your right to left with it
tilted slightly to your left. (OPT8)
c) When mowing a wide area, start working from
your left end to avoid interference of cut grass.
d) The blade may be seized by weeds if the engine
speed is too low, or the blade cuts too deep into
weeds. Adjust the engine speed and cutting
depth according to the condition of object.
WARNING
• If the grass or other object gets caught in the
blade, or if the unit starts to shake or vibrate,
turn off the engine and check the whole unit.
Change the blade if it has been damaged.
• Turn off the engine and make sure the blade
has completely stop before checking the
blade, and removing any object got caught
in.
OPT9
■ OPERATION
1. Check the bolt to fasten the blade and be sure
the bolt has no fault, and no abrasion.
2. Be sure that the blade and the holder have been
fastened according to instruction and the blade
turns smoothly without abnormal noise. (OPT9)
WARNING
• The rotating parts fastened incorrectly may
cause serious accident to the operator.
• Make sure that the blade is not bent, warped,
cracked, broken or damaged.
• If you find any error to the blade, discard it
and change new one which is certified by
RedMax.
❲ 27 ❳
11. Optional blade usage
OPT10
■ By using the shoulder strap, hang the unit on
your right side. Adjust the strap length so that
the cutting head may become parallel to the
ground. (OPT10)
WARNING
Make sure to use shoulder strap and debris
guard. If not, it is vary dangerous when you slip
or lose your balance.
WARNING
■ CONTROLLING BLADE BOUNCE
• Kick out can cause serious personal injury.
Carefully study this section. It is important that
you understand what causes kick out, how you
can reduce the chance of kick out and how you
can remain in control of the unit if kick out does
occur.
1. What causes kick out:
• Kick out can occur when the moving blade
contacts an object that it cannot cut. This contact
causes the blade to stop for an instant and then
suddenly move or ”bounce” away from the object
that was hit. The operator can lose control of the
unit and the blade can cause serious personal
injury to the operator or any person nearby if the
blade contacts any part of the body.
2. How you can reduce the chance of kick out:
a. Recognize that kick out can happen. By
understanding and knowing about bounce,
you can help eliminate the element of
surprise.
b. Cut fibrous weeds and grass only. Do not
let the blade contact materials it cannot cut
such as hard, woody vines and brush or
rocks, fences, metal, etc
c. Be extra prepared for bounce if you must cut
where you cannot see the blade making
contact such as in areas of dense growth.
d. Keep the blade sharp. A dull blade increase
the chance of bounce.
e. Avoid feeding the blade too rapidly. The blade
can bounce away from material being cut if
❲ 28 ❳
11. Optional blade usage
the blade is fed faster than its cutting
capability.
f. Cut only from your right to your left.
g. Keep your path of advance clear of material
that has been cut and other debris.
OPT11
3. How you can maintain the best control:
a. Keep a good, firm grip on the unit with both
hands. A firm grip can help neutralize bounce.
Keep your right and left hands completely
around the respective handles.
b. Keep both feet spread apart in a comfortable
stance and yet braced for the possibility that
the unit could bounce. Do not overreach.
Keep firm footing and balance.
■ MAINTENANCE
BLADE
• Check the blade and the fasteners for
looseness, cracking, or bending.
• Check the cutting edges and reform with a flat
file.
Point (OPT11) :
1. Keep the end corner sharp.
2. Round the root of the edge, using round file.
3. Do not use water when using a grinder.
IMPORTANT
• It is recommended that filing should be done by
professionals.
• Especially regarding filing the 22,24-tooth blade,
Leave it to the professionals.
■ TRANSPORTING THE UNIT
• When you finish cutting in one location and wish
to continue work in another spot, turn off the
engine, and lift up the unit and carry it paying
attention fo the blade.
• Never forget to place the protective cover over
the blades.
• When transporting the unit over long distances,
detach the blade fix the unit by ropes.
❲ 29 ❳
12. Troubleshooting guide
Case 1. Starting failure
CHECK
fuel tank
fuel filter
carburetor adjustment screw
sparking (no spark)
spark plug
➞
➞
➞
➞
➞
➞
PROBABLE CAUSES
incorrect fuel
fuel filter is clogged
out of normal range
spark plug is fouled/wet
plug gap is incorrect
disconnected
➞
➞
➞
➞
➞
➞
ACTION
drain it and with correct fuel
clean
adjust to normal range
clean/dry
correct (GAP: 0.6~0.7mm)
retighten
Case 2. Engine starts but does not keep running/Hard re-starting.
CHECK
fuel tank
carburetor adjustment screw
muffler,cylinder (exhaust port)
air cleaner
cylinder fin, fan cover
➞
➞
➞
➞
➞
PROBABLE CAUSES
incorrect fuel or staled fuel
out of normal range
carbon is built-up
clogged with dust
clogged with dust
➞
➞
➞
➞
➞
ACTION
drain it and with correct fuel
adjust to normal range
wipe away
wash
clean
When your unit seems to need further service, please consult with our RedMax service shop in your area.
❲ 30 ❳
13. Parts list
BRUSHCUTTERS
BC225DL
NOTE :
1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or
replacement.
2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the
use of any parts other than those specified by the company.
3. When placing parts orders for repair and/or replacement, check if the model name and the
serial number are applicable to those specified in the parts list, then use parts number
described in the parts list.
4. The contents described in the parts list may change due to improvement.
5. The parts for the machine shall be supplied seven (7) years after the machine is
discontinued. [It is possible that some specific parts may be subject to change of their
delivery term and list price within the limit of ten (7) years after the machine is
discontinued. It is also possible that some parts may be available even after the limit of
seven (7) years.]
APPLICABLE SERIAL NUMBERS :
DRIVE UNIT 000101 and up
Dec. 2000
ENGINE UNIT 000101 and up
❲ 31 ❳
13. Parts list
Fig.1 DRIVE UNIT BC225DL (S/N 000101 and up)
❲ 32 ❳
Fig.1 DRIVE UNIT BC225DL (S/N 000101 and up)
Key#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Description
PIPE COMP
SHAFT
GEARCASE-ASS’Y
• GEARCASE
• BEARING
• BEARING
• RING
• SHAFT COMP
• BOLT
• WASHER
• PINION
• BEARING
• RING
• SNAP RING
• FITTING
• WASHER
• BOLT
• HOLDER(A)
• HOLDER(B)
• BOLT
GRIP
LEVER COMP
• LEVER
• CORD(A)
• CORD(B)
TUBE
CABLE COMP
PLATE NAME
PLATE
HANDLE ASSY
• HANDLE
• CLAMP
• SCREW M5x35
GUARD ASSY
• GUARD COMP
• • GUARD
• • BLADE
• • NUT
• • SCREW
• CLAMP
• BOLT
GOGGLE
TAP. HEAD COMP
• CASE COMP
• COVER
• CORD HOLDER
• PLATE
• SPRING
• PLATE
• CORD
Part Number Q'ty
T3108-12100
6784-12210
T3108-13000
T3300-13120
T3300-13510
T3300-13520
04065-02612
T3300-13200
3560-13261
3560-13290
T3300-13310
T3300-13530
T3300-13330
04065-02412
3199-13350
01641-20608
01252-30520
T3300-13240
6019-13250
01252-30510
3577-32141
T3002-12200
6110-14410
T3002-12220
T3002-12230
T3003-14510
1855-82100
T3108-12510
6425-12552
6420-14100
6420-14311
6420-14320
0263-90535
6357-24001
6357-24101
6041-24113
6041-24140
3320-15310
0263-30512
3520-24120
3540-24130
T3002-91190
PT104
6460-15113
6460-15131
6460-15142
3268-15150
6041-99162
3268-15170
6460-15180
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
Key#
Description
51 • SPACER
52 SHAFT
Part Number Q'ty
6460-15210
6041-99240
1
1
OPTIONAL BLADE & ACCESSORIES
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
9” 22-tooth
9” 24-tooth
8” 8-tooth
9” 8-tooth
8” 4-tooth
9” 4-tooth
J-HANDLE
BRACKET
COVER
HANGER-ASSY
• HANGER-COMP
• • HANGER
• • CLAMP
• • SLEEVE
• SCREW
STRAP-ASSY
SST229
SST249
SGB088
SGB089
SGB048
SGB049
6367-14200
3583-14101
6420-13280
6420-17300
6420-17400
9366-17110
9366-17120
6420-17410
0263-90525
T3002-17200
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
❲ 33 ❳
13. Parts list
Fig.2 ENGINE UNIT BC225DL (S/N 000101 and up)
❲ 34 ❳
Fig.2 ENGINE UNIT BC225DL (S/N 000101 and up)
Key#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Description
CYLINDER
GASKET, base
BOLT
PLUG RCJ-6Y
CRANKCASE-C
• PIN
GASKET
BEARING
SEAL
SEAL
SNAP RING
BOLT
GUARD
SCREW
CRANKSHAFT-C
PISTON
RING
PIN
RING
BEARING
WASHER
MUFFLER ASSY
ARRESTER
BOLT
GASKET
PLATE
SCREW
INSULATOR
GASKET, insulator
GASKET, carburetor
SCREW
CARBURETOR ASS'Y
• BODY ASS'Y
• • SCREEN
• • VALVE
• • SPRING
• • SCREW
• • PIN
• • LEVER
• BODY, purge
• COVER, pump
• PUMP, priming
• DIAPHRAGM
• GASKET, diaphragm
• DIAPHRAGM, pump
• GASKET, pump
• JET
• RING
• RING
• SWIVEL
• SCREW
• BRACKET
• NUT, adjuster
• SCREW, adjuster
• RING
• SCREW
• WASHER
BODY-ASSY
• BODY
• SLEEVE
• PLATE, choke
• LEVER, choke
• SCREW
Part Number Q'ty
5580-12110
5500-12213
1850-12130
5602-73110
5500-21100
2629-21130
5500-21141
06030-06001
2169-21210
1850-21220
04065-02812
01252-30530
5500-22110
0263-90514
5500-42001
5600-41111
1100-41210
1101-41310
1260-41320
5500-41410
1101-41340
T1702-15100
1601-15120
01252-30550
T1600-15210
5500-15221
0263-90416
T1700-13160
5500-13121
5500-13131
0263-90520
5501-81000
1850-81450
3306-81380
3356-81310
1850-81270
1850-81220
3310-81250
3310-81230
1850-81490
1850-81520
1751-81510
3310-81260
1850-81470
1065-81420
1065-81410
5500-81251
1751-81240
1751-81130
1881-81140
1752-81110
5500-81120
1751-81180
1918-81170
1881-81130
1850-81530
5500-81160
T1700-82100
5500-82111
1970-82190
T1700-82130
T1700-82140
2630-33610
1
1
2
1
1
3
1
2
1
1
1
3
1
1
1
1
2
1
2
1
2
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
4
1
1
1
2
1
1
1
Key#
Description
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
ELEMENT
COVER ASS'Y
• KNOB
SCREW
HOUSING-ASS`Y
• HOUSING
• BEARING
• DRUM
• RING
• RING
BRACKET (A)
BRACKET (B)
CUSHION
BOLT
BOLT
SCREW
COVER, engine
SCREW
SCREW
SHOE
SPRING
SCREW
WASHER
WASHER
ROTOR
COIL-A
• CAP
• CORD
• CAP
• GROMMET
• SPRING
BOLT
SPACER
CORD-C
NUT
KEY
RECOIL ASS'Y
• CASE-C
• REEL
• SPRING
• SCREW
• ROPE
• KNOB
• COLLAR
• SPRING
• WASHER
PULLEYASS'Y
• RATCHET
• SPRING
SCREW
TANK ASS'Y
• CAP ASS'Y
• • HOLDER ASS'Y
• • PACKING
• • FILTER
• PIPE-C
• FILTER ASS'Y
• CLIP
SCREW
CLIP
LABEL, recoil
Part Number Q'ty
5500-82171
T1701-82200
5500-82221
0263-90560
T1702-31100
T1701-31110
06002-06001
4810-31120
04064-01210
04065-02812
T1700-31211
T1700-31221
T1700-31231
01252-30522
01252-30510
0263-90520
T1700-32110
T1700-32160
0263-90514
1140-51111
T1700-51220
1140-51250
1140-51230
1970-51241
T1700-71110
T1700-71200
5500-72110
T1700-71220
2616-71320
5500-72130
5500-72120
3310-72150
T1700-71260
T1700-73200
1650-43230
1000-43240
T1700-75100
5500-75110
1850-75120
1850-75130
1850-75151
T1600-75160
T1600-75310
T1600-75320
T1600-75330
T1600-75210
1850-75201
1850-75221
1850-75230
T1700-32160
T1700-85000
5601-85201
5601-85300
5500-85220
5601-85260
4810-85300
5500-85400
1260-85460
5910-85510
1950-86120
T1702-75410
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
4
1
1
1
2
1
2
2
2
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
3
1
1
❲ 35 ❳
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board and KOMATSU ZENOAH are pleased to explain the
emission control system warranty on your 1995 and later small off-road engine. In California,
new small off-road engines must be designed, built and equipped to meet the state’s stringent
anti-smog standards. KOMATSU ZENOAH must warrant the emission control system on your
small off-road engine for the periods of time listed below provided there has been no abuse,
neglect or improper maintenance of your small off-road engine.
Your emission control system may include parts such as the carburetor and the ignition system.
Where a warrantable condition exists, KOMATSU ZENOAH will repair your small off-road engine
at no cost to you including diagnosis, parts and labor.
Manufacturer’s warranty coverage:
The 1995 and later small off-road engines are warranted for two years. If any emissionrelated part on your engine is defective, the part will be repaired or replaced by
KOMATSU ZENOAH.
Owner’s warranty responsibilities:
– As the small off-road engine owner, you are responsible for the performance of the
required maintenance listed in your owner’s manual. KOMATSU ZENOAH
recommends that you retain all receipts covering maintenance on your small off-road
engine, but KOMATSU ZENOAH can not deny warranty solely for the lack of receipts or
for your failure to ensure the performance of all scheduled maintenance.
– As the small off-road engine owner, you should be aware, however, that KOMATSU
ZENOAH may deny you warranty coverage if your small off-road engine or a part has
failed due to abuse, neglect, improper maintenance or unapproved modification.
– You are responsible for presenting your small off-road engine to a KOMATSU ZENOAH
distribution center as soon as a problem exists. The warranty repairs should be
completed in e reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should
contact KOMATSU ZENOAH AMERICA INC. at (770)-381-5147 or you can write to
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
RedMax TRIMMER/BRUSHCUTTER
MODEL BC225DL
2-YEAR LIMITED WARRANTY
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL
BC225DL UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY),
THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH
SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR
WORKMANSHIP. EMISSION-RELATED PARTS ARE:
THE CARBURETOR ASSY, COIL ASSY, ROTOR, SPARKPLUG,
AIR FILTER, FUEL FILTER, INTAKE MANIFOLD, AND THE GASKETS
ALL OTHER PARTS EXCEPT ABOVE PARTS, FOR TWO (2) YEARS OF HOME USE [ ONE (1) YEAR FOR ANY OTHER
USE ] FROM THE DATE OF ORIGINAL ANY DELIVERY OF THE MODEL BC225DL UNIT, THE COMPANY,
THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL PURCHASER,
ANY PART OF PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. THIS IS THE EXCLUSIVE
REMEDY.
THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE RedMax DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE RedMax DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF "REPAIR OR REPLACE AS
NECESSARY" SHALL BE WARRANTED FOR THE WARRANTY PERIOD.ANY WARRANTED PART WHICH IS
SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE SHALL BE WARRANTED FOR THE PERIOD OF
TIME UP TO THE FIRST SCHEDULED REPLACEMNET POINT FOR THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DULABILITY MAY BE USED IN NONWARRANTY MAINTENANCE OR REPAIRS, AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAIRURE OF A
WARRANTED PARTS STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF
INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS,
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBULICATION, USE OF ANY PARTS OR ACCESSARIES
OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE CONPANY'S CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN
THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE LIMITED TO TWO (2) YEARS OF HOME USE [ ONE (1) YEAR FOR ANY OTHER USE ] FROM THE ORIGINAL
DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES
ARE EXCLUDED.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMINATION OR EXCLUSION MAY
NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
IF YOU NEED TO OBTAIN INFORMATION ABOUT THE NEAREST SERVICE CENTER, PLEASE CALL KOMATSU
ZENOAH AMERICA INC. AT (770)-381-5147.
IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL
OUT THE CARD AND SEND IT TO RedMax / KOMATSU ZENOA AMERICA WITHIN SEVEN (7) DAYS.BE SURE TO KEEP
A COPY FOR YOUR RECORDS.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
RedMax TRIMMER/BRUSHCUTTER
Modèle BC225DL
Garantie limitée à 2 ans
Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par
l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour
l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage
défectueux pendant deux (2) ans à compter de la date initiale de livraison d’une unité du modèle BC225DL. Les
pièces en rapport avec les émissions de gaz d'échappement sont:
l'assemblage carburateur, l'assemblage bobine, le rotor, la bougie,
le filtre à air, le filtre à carburant, la tubulure d'admission et les joints
Toutes autres pièces exceptées celles mentionnées ci-dessus : La société, par l'intermédiaire de n'importe quel
revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial toute(s) pièce (s) se
révélant de constitution et/ou de montage défectueux pendant deux (2) ans en cas d’utilisation privée [un (1) an pour
toute autre utilisation] à compter de la date de livraison initiale d’une unité du modèle BC225DL. Telles sont les
limites de la garantie.
Le coût du transport de l'unité jusqu'au revendeur RedMax et depuis celui-ci sera à la charge de l'acheteur.
L'acheteur ne supportera pas le coût de main d'oeuvre du diagnostic qui amène à la conclusion qu'une pièce
garantie est défectueuse, si ce diagnostic est effectué chez le revendeur RedMax.
L’acheteur ou propriétaire a pour responsabilité d’effectuer l’entretien obligatoire tel que défini par le fabricant dans le
manuel du propriétaire/de l'utilisateur.
Toute pièce garantie dont le remplacement n'est pas prévu dans le cadre de l’entretien obligatoire, ou pour laquelle
est seulement prévue une inspection périodique pour "remplacement ou réparation si nécessaire" sera garantie pour
la période de garantie. Toute pièce garantie arrivée à l’échéance de son premier remplacement prévu sera garantie
jusqu’à celui-ci.
Toute pièce de rechange équivalente en performance ou en durabilité peut être utilisée pour l’entretien hors-garantie
ou les réparations hors-garantie, et ce sans réduire l’obligation de garantie incombant à la société.
La société sera tenue responsable des dommages aux autres composants du moteur causés par la défaillance de
pièce(s) garantie(s) en période de garantie.
La garantie ne s'applique pas aux unités endommagées par suite de: négligence dans la mise en oeuvre des
instructions spécifiées dans le manuel du propriétaire/de l'utilisateur en vue d’une utilisation et d’un entretien correct,
fausse manœuvre accidentelle, modification, utilisation abusive, lubrification incorrecte, utilisation de pièces ou
d’accessoires autres que ceux spécifiés par la société, ou autres causes hors du contrôle de la société.
Cette garantie ne couvre pas les pièces remplacées en raison de leur usure normale ou de changements
d’apparence sans effets.
Il n'existe aucune autre garantie explicite.
Les garanties implicites, celles de négociabilité du produit et de son adaptabilité à un usage défini incluses, sont
limitées à deux (2) ans pour un usage privé [un (1) an pour toute autre utilisation] à compter de la date initiale de
livraison.
Les responsabilités pour les dommage conséquents ou incidents sont exclues de toutes les garanties.
Certaines provinces n'autorisant pas les limitations à la durée des garanties implicites, ou les exclusions ou
limitations relatives aux dommages incidents ou conséquents, la limitation indiquée ci-dessus peut ne pas vous être
applicable.
Cette garantie vous donne des droits juridiques spécifiques, et vous pouvez également jouir d’autres droits variant
d'une province à l'autre.
Si vous désirez obtenir des informations sur le centre de service le plus proche, veuillez appeler KOMATSU
ZENOAH AMERICA INC. au (770)-381-5147
Note importante: vous recevrez une carte d'enregistrement de garantie au moment de l'achat. Veuillez la remplir et
l'adresser à RedMax / KOMATSU ZENOAH AMERICA sous sept (7) jours en prenant soin de conserver une copie
pour vous.
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
KOMATSU ZENOAH AMERICA INC.
4344 Shackleford Road Suite 500
Norcross, Georgia 30093
© Printed in Japan