Ultra chef U405 CART Instruction manual

This gas grill must be used only outdoors in a well-ventilated space and must not be used inside a
building, garage, screened-in porch, gazebo or any other enclosed area.
APPLY SERIAL NUMBER LABEL FROM CARTON
Serial No.
XXXXXX000000
MODEL NO.
U405 CART
UP405 PEDESTAL
WARNING
DANGER
IF YOU SMELL GAS:
• Shut off gas to the appliance.
• Extinguish any open flame.
• Open lid.
• If odor continues, keep away from the
appliance and immediately call your gas
supplier or fire department.
Do not try to light this appliance without
reading the “LIGHTING” instructions section of
this manual.
Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this
or any other appliance. An L.P. cylinder not
connected for use must not be stored in the
vicinity of this or any other appliance. If the
information in these instructions is not followed exactly, a fire or explosion may result,
causing property damage, personal injury or
death.
Notice to Installer: Leave these instructions with the grill owner for future reference.
Manufactured by: Napoleon Appliance Corp.,
214 Bayview Dr., Barrie, Ontario, Canada L4N 4Y8 Phone: (705) 726-4278
Fax: (705) 725-2564 email: wecare@napoleonproducts.com website: www.ultrachefgrills.com
N415-0184 JUN 14/10
2
ULTRA CHEF® gas grills are manufactured under the strict Standard of the world recognized ISO 9001-2008
Quality Assurance Certificate.
ULTRA CHEF® products are designed with superior components and materials, and are assembled by trained
craftsmen who take great pride in their work. The burner and valve assembly are leak tested and test-fired
at a quality test station, and thoroughly inspected by a qualified technician before packaging and shipping to
ensure that you, the customer, receive the quality product you expect from Napoleon Appliance Corporation.
ULTRA CHEF® GAS GRILL LIMITED LIFETIME WARRANTY
Napoleon Appliance Corporation warrants the following materials and workmanship in
your new ULTRA CHEF® gas grill against defects for as long as you own the gas grill. This
covers: aluminum castings (excluding paint), SOLIDO® side shelves, stainless steel side
shelves, LUXIDIO® side shelf end caps, wheels, knobs, stainless steel burners, stainless
steel lid inserts, and lid handles. Subject to the following conditions. During the first five
years Napoleon Appliance Corporation will provide replacement parts at our option free
of charge. From the sixth year to lifetime Napoleon Appliance Corporation will provide
replacement parts at 50% of the current retail price.
Components such as stainless steel sear plates, cooking grids, igniters (excluding batteries),
temperature gauges and brass valves are covered and Napoleon Appliance Corporation will
provide parts free of charge during the first two years of the limited warranty.
All other components including regulators, casters, warming racks, hoses and connectors,
fasteners and accessories are covered and Napoleon Appliance Corporation will provide
parts free of charge during the first year of the limited warranty.
Napoleon Appliance Corporation shall not be liable for any transportation charges, labour
costs or export duties.
Conditions And Limitations
“Napoleon Appliance Corporation” warrants its products against manufacturing defects to the original purchaser only, provided that the purchase was made
through an authorized ULTRA CHEF® dealer and is subject to the following conditions and limitations:”
This factory warranty is non-transferable and may not be extended what so ever by any of our representatives.
The gas grill must be installed by a licenced, authorized service technician or contractor. Installation must be done in accordance with the installation
instructions included with the product and all local and national building and fire codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, grease fires, hostile environments, accident, alterations, abuse or
neglect and parts installed from other manufacturers will nullify this warranty.
This limited warranty further does not cover any scratches, dents, painted finishes, corrosion or discolouring by heat, abrasive and chemical cleaners, nor
chipping on porcelain enamel parts, nor any components used in the installation of the gas grill.
Should deterioration of parts occur to the degree of non-performance within the duration of the warranted coverage, a replacement part will be provided.
In the first year only, this warranty extends to the replacement of warranted parts, which are defective in material or workmanship provided that the product has been operated in accordance with the operation instructions and under normal conditions.
After the first year, with respect to this President’s Limited Lifetime Warranty, Napoleon Appliance Corporation may, at its discretion, fully discharge all obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defective part(s).
Napoleon Appliance Corporation will not be responsible for the installation, labour or any other costs or expenses related to the re-installation of a warranted part, and such expenses are not covered by this warranty.
Notwithstanding any provision contained in this President’s Limited Lifetime Warranty Napoleon Appliance Corporation ‘s responsibility under this warranty
is defined as above and it shall not in any event extend to any incidental, consequential, or indirect damages.
This warranty defines the obligation and liability of Napoleon Appliance Corporation with respect to the ULTRA CHEF® gas grill and any other warranties
expressed or implied with respect to this product, its components or accessories are excluded.
Napoleon Appliance Corporation neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this
product. Napoleon Appliance Corporation will not be responsible for: over firing, blow outs caused by environmental conditions such as strong winds, or
inadequate ventilation.
Any damages to the gas grill due to weather damage, hail, rough handling, damaging chemicals or cleaners will not be the responsibility of Napoleon Appliance Corporation.
The bill of sale or a copy will be required together with a serial number and a model number when making any warranty claims from Napoleon Appliance
Corporation.
Napoleon Appliance Corporation reserves the right to have its representative inspect any product or part prior to honouring any warranty claim.
Napoleon Appliance Corporation shall not be liable for any transportation charges, labour costs, or export duties.
www.ultrachefgrills.com
3
WARNING! Failure to follow these instructions could result in property damage, personal injury or
death. Read and follow all warnings and instructions in this manual prior to operating grill.
Safe Operating Practices
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This gas grill must be assembled exactly according to the instructions in the manual. If the grill was store
assembled, you must review the assembly instructions to confirm correct assembly and perform the required leak tests before operating the grill.
Read the entire instruction manual before operating the gas grill.
This gas grill must be used only outdoors in a well-ventilated space and must not be used inside a building,
garage, screened-in porch, gazebo or any other enclosed area.
This gas grill must not be installed in or on recreational vehicles and/or boats.
Do not locate unit in windy settings. High winds adversely affect the cooking performance of the gas grill.
Under no circumstances should this gas grill be modified.
Do not operate unit under overhead combustible construction.
Maintain proper clearance to combustibles 20” (508 mm) to rear of unit, 6” (152 mm) to sides. Additional clearance of 24” (610mm) is recommended near vinyl siding or panes of glass.
Gas must be turned off at the propane cylinder or at the natural gas supply valve when the gas grill is not
in use.
Do not attempt to use a cylinder that is not equipped with a QCC1 type connection.
When the propane cylinder is connected to the appliance, the gas grill and cylinder must be stored outdoors in a well-ventilated space.
When the gas grill is to be stored indoors, the connection between the propane cylinder and the gas grill
must be disconnected and the cylinder removed and stored outdoors in a well ventilated space out of
reach of children. Disconnected cylinders must not be stored in a building, garage or any other enclosed
area. Natural gas units must be disconnected from the supply when being stored indoors.
Inspect the fuel supply hose before each use. If there is evidence of excessive abrasion or wear or the hose
is cut, it must be replaced prior to using the gas grill with a replacement hose assembly specified by the
grill manufacturer.
Do not route hose underneath drip pan - proper hose clearance to bottom of unit must be maintained.
Hose must not run behind the front leg. It must run around the front side of leg (if applicable).
Leak test the unit before initial use, annually, and whenever any gas components are replaced.
Follow lighting instructions carefully when operating grill.
Burner controls must be off when turning supply cylinder valve on.
The lid is to be closed during the gas grill preheating period on all models except the BISZ300NFT/PFT and
the built-in side burner BISB245.
The BISZ300NFT/PFT and the built-in side burner BISB245 are supplied with a flat cover for storage and
protection from the elements. Never place this cover on the grill while hot or operating. Allow grill to cool
completely before covering.
Adults and especially children should be alerted to the hazards of high surface temperatures. Young children should be supervised near the gas grill.
Do not leave grill unattended when operating.
Do not light burners with lid closed.
Do not operate rear burner with main burners operating.
Do not move grill when hot or operating.
Do not use condiment tray to store lighters, matches or any other combustibles.
Keep any electrical supply cord and fuel supply hose away from any heated surfaces.
Ensure sear plates are positioned properly according to sear plate installation instructions. The holes must
be towards the front of the gas grill (if applicable).
Clean grease tray and sear plates regularly to avoid build-up, which could lead to grease fires.
Remove warming rack before lighting rear burner. The extreme heat will damage the warming rack.
Inspect infrared burner venturi tube for spider webs and other obstructions periodically. Clean the tubes
completely if you find any such obstructions.
Do not allow cold water (rain, sprinkler, hose, etc.) to come in contact with heated unit. A large temperature differential can cause chipping in the porcelain.
Do not allow cold water (rain, sprinkler, hose, etc.) to come in contact with ceramic burners. A large temperature differential can cause cracking in the ceramic tile.
Do not use a pressure washer to clean any part of the unit.
www.ultrachefgrills.com
4
General Information
This Gas Barbecue Is Certified Under Canadian And American National Standards, CAN/CGA-1.6b-2002 and
ANSI Z21.58b-2002 respectively for Outdoor Gas Grills and should be installed to conform with local codes. In
absence of local codes, install to the current CAN/CSA-B149.1 Propane Installation Code in Canada or to the
National Fuel Gas Code, ANSIZ223.1/NFPA 54 in the United States.
If a rotisserie motor is used, it must be electrically grounded in accordance with local codes or, in absence of
local codes, with the current CSA C22.1Canadian Electrical Code in Canada or the National Electrical Code,
ANSI/NFPA 70 in the United States.
California proposition 65: The burning of gas fuel creates by-products, some of which are on the list as
substances known by the State of California to cause cancer or reproductive harm. When cooking with gas,
always ensure adequate ventilation to the unit, to minimize exposure to such substances.
Propane Cylinder Specifications
WARNING! If these instructions are not followed exactly, a fire causing death or serious injury may
occur.
A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a
cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in accordance
with the specifications for LP-gas cylinders of the National Standard of Canada, CAN/CSA-b339, Cylinders,
Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable or the Specifications for LP-Gas Cylinders of the U.S. Department of Transportation (D.O.T.). This appliance has been designed for use with a 20 lb. (9.1 kg) size propane cylinder only (not supplied).
The propane cylinder must be provided with a cylinder connection device compatible with the connection
for outdoor cooking appliances. The propane cylinder must be provided with a shut-off valve terminating in
a propane cylinder valve type QCC1, and a safety relief device having direct communication with the vapor
space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and the cylinder
shall include a collar to protect the cylinder valve. The cylinder shall incorporate a listed OPD (overfill protection device). Do not store a spare LP-gas cylinder under or near this appliance. Never fill the cylinder beyond
80 percent full.
Use only the pressure regulator and hose assembly provided with this barbecue. Replacement pressure regulators and hose assemblies must be specified by the manufacturer. Do not store a spare propane cylinder on
the shelf beneath the barbecue.
The regulator supplies a pressure of 11 inches. water column to the gas grill and has a QCC1 type fitting. Cylinders to be used with this unit must be supplied with a QCC1 cylinder valve. A QCC1 cylinder has a positive
seating connection, which will not allow gas flow until a positive seal has been achieved. It is also equipped
with an excess flow device. In order to attain full flow to the grill, the valves must be in the off position when
the cylinder valve is turned on.
Gas Hook-Up Instructions
WARNING! A fire will result if the gas supply hose makes contacts with the underside of the grill or
drip pan.
Cylinder Connection: Ensure that the gas regulator hose is kink free. Remove the cap or plug from the cylinder
fuel valve. Insert the black QCC1 regulator nipple onto the QCC1 fuel valve. Hand tighten clockwise. Do not use
tools. Leak test all joints prior to using the barbecue. A leak test must be performed annually, and each time a
cylinder is hooked up, or if a part of the gas system is replaced.
If this grill is to be connected directly to a house propane gas supply line, follow the instructions for the natural
gas hook up. Optional side burners must also follow the natural gas hook up instructions. Note: The propane
tank heat shield is not required when the grill is connected to a fixed fuel supply, as its sole function is to shield
the propane tank normally used with the grill. Ensure that the supply pressure being supplied to the unit is
11” water column.
Propane Cylinder Installation: Set cylinder into the groove of the lower tank mounting bracket. Ensure that
tank valve faces away from the barbecue. Lower the top tank mounting bracket onto the cylinder and tighten
with wing nut.
IMPORTANT! Ensure that the hose is routed around the front side of the cart leg to maintain proper
clearance to the underside of the unit.
www.ultrachefgrills.com
5
Natural Gas Hook-Up: This natural gas grill is supplied with a 10ft (3m) supply hose (complete with a quick
disconnect) designed for natural gas and certified for outdoor use. The gas grill is designed to operate at an
inlet pressure of 7 inches water column. Piping and valves upstream of the quick disconnect are not supplied.
The installation must comply with CAN B149.1 Natural Gas and Propane installation code in Canada, or to the
National Fuel Gas Code, ANSI Z223.1 in the United States. The gas supply pipe must be sufficiently sized to
supply the BTU/h specified on the rating plate, based on the length of the piping run. The quick disconnect
must not be installed in an upward direction and a readily accessible manual shut-off valve must be installed
upstream of, and as close to, the quick disconnect as is feasible. The flared end of the hose must be connected
to the fitting on the end of the flex tube as illustrated in the Natural Gas Hose Attachment diagram. Tighten
using two wrenches. (Do not use thread sealer/pipe dope.) These connections must be made by a licensed gas
installer. Leak test all joints prior to using the gas grill.
IMPORTANT! Ensure that the hose is routed around the front side of the cart leg to maintain proper
clearance to the underside of the unit.
Non-Side Burner Units: Connect the flared end of the hose to the fitting on the end of the manifold tube.
Wrench tighten. (Do not use thread sealer/pipe dope.)
Side Burner Units: Connect the 20 inch hose from the manifold, to the side burner as illustrated in the Natural
Gas Hose Attachment diagram. Connect the supply hose to the flare connection, which faces down from the
side burner. Tighten all connections using two wrenches. (Do not use thread sealer/pipe dope.)
WARNING!
•
The installation must be performed by a licensed gas fitter, and all connections must be leak tested before
operating the grill.
•
Do not route hose underneath drip pan.
•
Do not route hose between space in bottom shelf and back panel.
•
Do not route hose over top of rear panel.
•
Ensure all hose connections are tightened using two wrenches. Do not use Teflon tape or pipe dope on
any hose connection.
•
Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire.
•
Leak test all the connections using a soap and water solution, as per the leak testing instructions found in
this manual.
Leak Testing Instructions
WARNING! A leak test must be performed annually and each time a cylinder is hooked up or if a part
of the gas system is replaced.
Warning! Never use an open flame to check for gas leaks. Be certain no sparks or open flames are
in the area while you check for leaks. Sparks or open flames will result in a fire or explosion, damage to
property, serious bodily injury, or death.
Leak testing: This must be done before initial use, annually, and whenever any gas components are replaced
or serviced. Do not smoke while performing this test, and remove all sources of ignition. See Leak Testing
Diagram for areas to check. Turn all burner controls to the off position. Turn gas supply valve on.
Brush a half-and-half solution of liquid soap and water onto all joints and connections of the regulator, hose,
manifolds and valves.
Bubbles will indicate a gas leak. Either tighten the loose joint or have the part replaced with one recommended by the Customer Care department and have the grill inspected by a certified gas installer.
If the leak cannot be stopped, immediately shut off the gas supply, disconnect it, and have the grill inspected
by a certified gas installer or dealer. Do not use the grill until the leak has been corrected.
www.ultrachefgrills.com
6
Lighting Instructions
Rear Burner
Lighting Hole
Igniter
Left Burner Centre Burner
Right Burner
Off Position
WARNING! Open lid
WARNING! Ensure all burner controls are in the off position. Slowly turn on the gas
supply valve.
Main Tube Burner
Lighting
Rear Burner Lighting
Main Infrared Burner
Lighting
(if equipped)
Side Burner Lighting
(if equipped)
1. Open grill lid
1. Open grill lid
1. Open grill lid
1. Open burner cover.
2. Turn left burner control
to high position.
2. Remove warming rack
and hanging basket.
2. Turn infrared burner
control to high position.
2. Turn side burner control
to high position.
3. Press and hold
igniter button until burner
lights, or light by match.
3. Light match and hold to
ports on left side of rear
burner.
3. Press and hold
igniter button until burner
lights, or light by match.
3. Press and hold
igniter button until burner
lights, or light by match.
4. If ignition is not
immediate, turn burner
control off. Wait 5
minutes.
Repeat.
4. Turn rear burner control
to high position.
4. If ignition is not
immediate, turn burner
control off. Wait 5
minutes. Repeat.
4. If ignition is not
immediate, turn burner
control off. Wait 5
minutes. Repeat.
5. With left tube burner
operating on high, turn the
center and/or right tube
burner to high.
5. If ignition is not
immediate, turn burner
control off. Wait 5
minutes.
WARNING! The propane cylinder is equipped with an excess flow device.
Unless all burners are
turned off prior to turning the cylinder on, only small flames and low heat will be
achievable.
WARNING! Do not use rear burner while operating main burner.
www.ultrachefgrills.com
7
Cooking Instructions
Initial Lighting: When lit for the first time, the gas grill emits a slight odor. This is a normal temporary condition
caused by the “burn-in” of internal paints and lubricants used in the manufacturing process and does not occur
again. Simply run the main burners on high for approximately one-half hour.
Main Burner Use: When searing foods, we recommend preheating the grill by operating all main burners
in the high position with the lid closed for approximately 10 minutes. Food cooked for short periods of time
(fish, vegetables) can be grilled with the lid open. Cooking with the lid closed will ensure higher, more even
temperatures that can reduce cooking time and cook meat more evenly. Food that has a cooking time longer
than 30 minutes, such as roasts, can be cooked indirectly (with the burner lit opposite to the food placement).
When cooking very lean meats, such as chicken breasts or lean pork, the grids can be oiled before pre-heating
to reduce sticking. Cooking meat with a high degree of fat content can create flare-ups. Either trim the fat or
reduce temperatures to inhibit this. Should a flare-up occur, move food away from the flames and reduce the
heat. Leave the lid open. See Your All Season Grill cookbook by Napoleon for more detailed instructions.
Direct Cooking: Place food to be cooked on the grill directly over the heat. This method is generally used for
searing or for foods that do not require prolonged cooking times such as hamburgers, steaks, chicken pieces,
or vegetables. The food is first seared to trap-in the juices and flavor, and then the temperature is lowered to
finish cooking the food to your preference.
Indirect Cooking: With one or more burners operating, place food to be cooked on the grill over a burner that
is not operating. The heat circulates around the food, cooking slowly and evenly. Cooking with this method is
much the same as cooking in your oven and is generally used for larger cuts of meats such as roasts, chickens
or turkeys, but can also be used for cooking foods that are prone to flare-ups or for smoking foods. Lower temperatures and slower cooking times result in tender foods.
Rear Burner Use (If Equipped): Remove the warming rack prior to use. Cooking grids should also be removed
if they interfere with the rotisserie. The rear burner is designed to be used in conjunction with the rotisserie
kit (included with most rear burner units) available from your dealer. See the rotisserie kit assembly instructions.
To use the counterbalance - remove the rotisserie motor from the gas grill. Place the spit with meat being
cooked across the hangers inside the grill. The meat will naturally hang with the heavy side down. Tighten
the counterbalance arm and weight so the arm is facing up. Slide the counterweight in or out to balance the
load and tighten in place. Re-install the motor and begin cooking. Place a metal dish underneath the meat to
collect drippings for basting and naturally delicious gravy. Basting liquid may be added as required. To seal in
juices, first operate rear burner on high until brown, then reduce the heat to thoroughly cook foods. Keep the
lid closed for best results. Your roasts and fowl will brown perfectly on the outside and stay moist and tender
on the inside. For example, a 3 pound chicken on the rotisserie will be done in approximately 1½ hours on
medium to high. See ‘Your all Season Grill’ cookbook by Napoleon for more detailed instructions.
WARNING! Barbecue sauce and salt can be corrosive and will cause rapid deterioration of the gas grill
components unless cleaned regularly. When finished cooking disassemble rotisserie components, wash
thoroughly with warm soapy water and store indoors.
Side Burner Use (if equipped): The side burner can be used like any stove top burner, for gravies, soups etc.
For best performance, the gas grill should be located with the side burner protected from the wind.
WARNING! Never grill food directly on the side burner grate.
It is designed for use with pots and pans
only.
www.ultrachefgrills.com
8
Cleaning Instructions
Warning! Always wear protective gloves and safety glasses when cleaning your grill.
Warning! To avoid the possibility of burns, maintenance should be done only when the grill is cool.
Avoid unprotected contact with hot surfaces. Ensure all burners are turned off. Clean grill in an area where
cleaning solutions will not harm decks, lawns, or patios. Do not use oven cleaner to clean any part of this
gas grill. Do not use a self-cleaning oven to clean cooking grids or any other parts of the gas grill. Barbecue sauce and salt can be corrosive and will cause rapid deterioration of the gas grill components unless
cleaned regularly.
Note: Stainless steel tends to oxidize or stain in the presence of chlorides and sulfides, particularly in coastal
areas and other harsh environments, such as the warm, highly humid atmosphere around pools and hot tubs.
These stains could be perceived as rust, but can be easily removed or prevented. To provide stain prevention
and removal, wash all stainless steel surfaces every 3-4 weeks or as often as required with fresh water and/or
stainless steel cleaner.
Grids And Warming Rack: The grids and warming rack are best cleaned with a brass wire brush during the preheating period. Steel wool can be used for stubborn stains. It is normal that stainless grids (if equipped) will
discolor permanently from regular usage due to the high temperature of the cooking surface.
Cast Iron Cooking Grids: The cast iron cooking grids supplied with your new grill offer superior heat retention
and distribution. By regularly seasoning your grids you are adding a protective coating, which will aid in resisting corrosion and increase your grids non-stick capabilities.
First Time Use: Wash the cooking grids by hand with mild dish soap and water to remove any residue from
the manufacturing process (never wash in a dish washer). Rinse thoroughly with hot water and dry completely
with a soft cloth. This is important to avoid moisture from entering the cast iron.
Seasoning: Using a soft cloth, spread VEGETABLE SHORTENING over the entire grid surface ensuring all grooves
and corners are covered. Do not use salted fats such as butter or margarine. Pre-heat your grill for 15 minutes, then place the seasoned cooking grids in the grill. Turn the burner control knobs to medium with the
lid closed. Allow the cooking grids to heat for approximately one-half hour. Turn all the burners to the “OFF”
position and turn the gas off at the source. Let the cooking grids stand until cool. This procedure should be
repeated several times throughout the season, although it is not required for daily use (follow daily usage
procedure below).
Daily Usage: Before pre-heating, and cleaning with a brass wire grill brush, coat the entire top surface of the
cooking grids with VEGETABLE SHORTENING. Pre-heat the grill and then brush away any unwanted residue
with a brass wire brush.
Stainless Steel Cooking Grids: (upgrade kit available - see replacement parts list). Stainless steel cooking grids
are durable and corrosion resistant. They require less seasoning and maintenance then cast iron cooking grids.
It is recommended that you follow the daily usage procedure listed above although you may find pre-heating
and cleaning your grids with a wire brush is sufficient for your grilling needs.
Control Panel: The control panel text is printed directly on the stainless steel and with proper maintenance will
remain dark and legible. To clean the panel, use only warm soapy water or Continental brand stainless steel
cleaner available from your Ultra Chef dealer. Never apply abrasive cleaners on any stainless surfaces, especially the printed portion of the control panel or the printing will gradually rub off.
Cleaning Inside The Gas Grill: Remove the cooking grids. Use a brass wire brush to clean loose debris from
the casting sides and underneath the lid. Scrape the sear plates with a putty knife or scraper, and use a wire
brush to remove the ash. Remove the sear plates and brush debris from the burners with the brass wire brush.
Sweep all debris from inside the gas grill into the drip pan.
Drip Pan: Accumulated grease is a fire hazard. Clean the drip pan frequently (every 4 – 5 uses or as often as required) to avoid grease buildup. Grease and excess drippings pass through to the grease tray, located beneath
the gas grill and accumulate in the disposable grease tray below the grill. To access the disposable grease tray
or to clean the drip pan, slide the drip pan free of the grill. Never line the drip pan with aluminum foil, sand or
any other material as this could prevent the grease from flowing properly. The pan should be scraped out with
a putty knife or scraper. Replace the disposable grease tray every 2 – 4 weeks, depending on gas grill usage.
For supplies, see your Ultra Chef Gas Grill dealer.
Cleaning The Outer Grill Surface: Do not use abrasive cleaners or steel wool on any painted, porcelain or stainless steel parts of your Ultra Chef Grill. Doing so will scratch the finish. Exterior grill surfaces should be cleaned
with warm soapy water while the metal is still warm to the touch. To clean stainless surfaces, use a stainless
steel or a non-abrasive cleaner. Always wipe in the direction of the grain. Over time, stainless steel parts
discolor when heated, usually to a golden or brown hue. This discoloration is normal and does not affect the
performance of the grill. Porcelain enamel components must be handled with additional care. The baked-on
enamel finish is glass-like, and will chip if struck. Touch-up enamel is available from your Ultra Chef Grill dealer.
Solido Side Shelves: Clean side shelves with warm soapy water and a plastic bristled brush.
www.ultrachefgrills.com
9
Maintenance Instructions
We recommend this gas grill be thoroughly inspected and serviced annually by a qualified service person.
WARNING! Always wear protective gloves and safety glasses when cleaning your grill.
WARNING! Turn off the gas at the source and disconnect the unit before servicing. To avoid the possibility of burns, maintenance should be done only when the grill is cool. A leak test must be performed
annually and whenever any component of the gas train is replaced or gas smell is present.
Combustion Air Adjustment: (This must be done by a qualified gas installer.) The air shutter is factory set and
should not need adjusting under normal conditions. Under extreme field conditions, adjustments might be
required. When the air shutter is adjusted correctly the flames will be dark blue, tipped with light blue and
occasionally yellow.
• With too little air flow to the burner, the flames are lazy yellow and can produce soot.
• With too much air flow, the flames lift erratically and can cause difficulties when lighting.
Adjusting the air shutter:
1. Remove cooking grids and sear plates and leave lid open. The back cover must be removed for rear tube
burner air shutter adjustment.
2. Loosen air-shutter lock screw located at the mouth of the burner and open or close air shutter as required.
The normal opening settings are:
Main Tube Burner Propane3/16” (5mm)
Rear Tube Burner Propane3/8” (10mm)
Natural 1/8” (3mm)
Natural 1/8” (3mm)
*Infra-Red burners have no air adjustment.
3. Light the burners and set to high. Visually inspect burner flames. When the shutters are set correctly, turn
burners off, tighten locking screws, and replace removed parts. Ensure that the insect screens are installed.
Light Blue
Burner
Burner Port
Yellow Tipping
Dark Blue
Approximately
1/2” (13mm)
Burner: The burner is made from heavy wall 304 stainless steel, but extreme heat and a corrosive environment
can cause surface corrosion to occur. This can be removed with a brass wire brush.
CAUTION! Beware of Spiders.
Spiders and insects are attracted to the smell of propane and natural gas. The burner is equipped with an insect screen on
the air shutter, which reduces the likelihood of insects building nests inside the burner but does not entirely eliminate the
problem. A nest or web can cause the burner to burn with a soft yellow or orange flame or cause a fire (flashback) at the air
shutter underneath the control panel. To clean the inside of the burner, it must be removed from the gas grill: Remove the
screw (s) that attaches the burner to the back wall. Slide the burner back and up wards to remove.
Cleaning: Use a flexible venturi tube brush to clean the inside of the burner. Shake any loose debris from the
burner through the gas inlet. Check the burner ports and valve orifices for blockages. Burner ports can close
over time due to cooking debris and corrosion, use an opened paperclip or the supplied port maintenance bit
to clean them. Drill out blocked ports using this drill bit in a small cordless drill. The ports are easier to clean
if the burner is removed from the grill, but it can also be done with the burner installed. Do not flex the drill
bit when drilling the ports, as this will cause the drill bit to break. This drill is for burner ports only, not for the
brass orifices (jets) which regulate the flow into the burner. Take care not to enlarge the holes. Ensure the
insect screen is clean, tight, and free of any lint or other debris.
Reinstallation: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when
installing. Replace sear plate mount and tighten screws to complete reinstallation.
www.ultrachefgrills.com
10
Warning! When reinstalling the burner after cleaning it is very
important that the valve/orifice enters the burner tube before lighting your
gas grill. If the valve is not inside the burner tube a fire or explosion could
occur.
WARNING! Hose: Check for abrasions, melting, cuts, and cracks in the hose. If any of these conditions
exist, do not use the gas grill. Have the part replaced by your Ultra Chef Gas Grill dealer or qualified gas
installer.
Aluminum Castings: Clean castings periodically with warm soapy water. Aluminum will not rust, but high
temperatures and weathering can cause oxidation to occur on aluminum surfaces. This appears as white spots
on the castings. To refinish these areas, clean first and sand lightly with fine sandpaper. Wipe the surface to
remove any residue and paint with high temperature barbecue paint. Protect surrounding areas from overspray. Follow the manufacture’s directions for curing.
Troubleshooting
Problem
Possible Causes
Solution
Low heat / Low flame when valve
turned to high.
For propane - improper lighting
procedure.
Ensure lighting procedure is followed carefully. All gas grill
valves must be in the off position when the tank valve is turned
on. Turn tank on slowly to allow pressure to equalize. See
lighting instructions.
For natural gas - undersized supply
line.
Pipe must be sized according to installation code.
For both gases - improper
preheating.
Excessive flare-ups/uneven heat.
Preheat grill with both main burners on high for 10 to 15
minutes.
Sear plates installed incorrectly.
Ensure sear plates are installed with the holes towards the
front and the slots on the bottom. See assembly instructions.
Improper preheating.
Preheat grill with both main burners on high for 10 to 15
minutes.
Excessive grease and ash build on
sear plates and in drip pan.
Clean sear plates and drip pan regularly. Do not line pan with
aluminum foil. Refer to cleaning instructions.
Burners burn with yellow flame,
accompanied by the smell of gas.
Possible spider web or other
debris, or improper air shutter
adjustment.
Thoroughly clean burner by removing. See general
maintenance instructions. Open air shutter slightly according to
combustion air adjustment instructions. (This must be done by
a qualified gas installer.)
Flames lift away from burner,
accompanied by the smell of
gas, and possibly difficulties in
lighting.
Improper air shutter adjustment.
Close air shutter slightly according to combustion air
adjustment instructions. (This must be done by a qualified gas
installer.)
Burner will not light with the
igniter, but will light with a
match.
Dead battery / or installed
incorrectly.
Replace with heavy duty battery.
Loose electrode wire or switch
terminal wires.
Check that electrode wire is firmly pushed onto the terminal
on the back of the igniter. Check that the lead wires from the
module to the ignition switch (if equipped) are firmly pushed
onto their respective terminals.
Wrong replacement igniter.
One spark systems must use a one spark igniter.
Improper gap at electrode tip.
Ensure that the collector box is tight and the gap between the
electrode end and the collector box is between 1/8” - 3/16”
(3mm-5mm). The gap can be adjusted by bending the box in
or out.
Lifting flames on burner.
Close air shutter slightly - see previous problem.
www.ultrachefgrills.com
11
Problem
Possible Causes
Solution
Humming regulator.
Normal occurrence on hot days.
This is not a defect. It is caused by internal vibrations in the
regulator and does not affect the performance or safety of the
gas grill. Humming regulators will not be replaced.
Burners will not cross light each
other.
Plugged ports along back of
burner.
Clean burner ports. See burner maintenance instructions.
“Paint” appears to be peeling
inside lid or hood.
Grease build-up on inside
surfaces.
This is not a defect. The finish on the lid and hood is porcelain,
and will not peel. The peeling is caused by hardened grease,
which dries into paint-like shards, that flake off. Regular
cleaning will prevent this. See cleaning instructions.
Burner output on “high” setting
is too low. (Rumbling noise and
fluttering blue flame at burner
surface.)
Lack of gas.
Check gas level in propane cylinder.
Supply hose is pinched.
Reposition supply hose as necessary.
Dirty or clogged orifice.
Clean burner orifice.
Spider webs or other matter in
venturi tube.
Clean out venturi tube.
Infrared burner (if equipped)
flashes back (during operation
the burner abruptly makes a
loud “whoosh” sound, followed
by a continuous blow-torch type
sound and grows dim.)
Pilot will not light.
(if equipped)
Propane regulator in “low flow”
state.
Ensure lighting procedure is followed carefully. All gas grill
valves must be in the off position when the tank valve is turned
on. Turn tank on slowly to allow pressure to equalize. See
lighting instructions.
Ceramic tiles overloaded with
grease drippings and build-up.
Ports are clogged.
Turn burner off and allow to cool for at least two minutes.
Relight burner and burn on high for at least five minutes or
until the ceramic tiles are evenly glowing red.
Burner overheated due to
inadequate ventilation (too much
grill surface covered by griddle
or pan.)
Ensure that no more than 75% of the grill surface is covered by
objects or accessories. Turn burner off and allow to cool for at
least two minutes, then relight.
Cracked ceramic tile.
Allow burner to cool and inspect very closely for cracks. If any
cracks are found, contact your authorized Ultra Chef dealer to
order a replacement burner assembly.
Leaking gasket surrounding the
ceramic tile, or a weld failure in
the burner housing.
Contact your authorized Ultra Chef dealer for instructions on
ordering a replacement burner assembly.
Lack of gas.
After turning pilot knob to high, wait approximately 20-30
seconds for air to purge the gas supply line while pressing
igniter. Fill propane cylinder. During initial set-up or after tank
has been refilled, it is best to light one of the tube burners
before lighting the pilot burner. This enables the gas to reach
the valves on the manifold more quickly.
Obstruction in pilot orifice.
Clean pilot orifice.
Electrode wire loose or off.
Replace lead wire.
Dirty pilot electrode.
Clean pilot electrode.
Pilot is actually lit.
The pilot flame, especially on natural gas units is very difficult
to see. Place your hand 1 in. (2.5 cm) above grill surface over
the pilot burner to feel for heat.
www.ultrachefgrills.com
12
KEEP YOUR RECEIPT AS PROOF OF PURCHASE TO VALIDATE YOUR WARRANTY.
Ordering Replacement Parts
Warranty Information
MODEL:
DATE OF PURCHASE:
SERIAL NUMBER:
(Record information here for easy reference)
Before contacting the Customer Care Department, check the NAC Website for more extensive cleaning, maintenance, troubleshooting and parts replacement instructions at www. ultrachefgrills.com. Contact the factory
directly for replacement parts and warranty claims. Our Customer Care Department is available between 9 AM
and 5 PM (Eastern Standard Time) at 1-866-820-8686 or fax at 1-705-727-4282. To process a claim, we must
be provided with the following information:
1. Model and serial number of the unit.
2. Part number and description.
3. A concise description of the problem (‘broken’ is not sufficient).
4. Proof of purchase (photocopy of the invoice).
In some cases the Customer Care Representative could request to have the parts returned to the factory for
inspection before providing replacement parts. These parts must be shipped prepaid to the attention of the
Customer Care Department with the following information enclosed:
1. Model and serial number of the unit.
2. A concise description of the problem (‘broken’ is not sufficient).
3. Proof of purchase (photocopy of the invoice).
4. Return Authorization Number - provided by the Customer Care Representative.
Before contacting customer care, please note that the following items are not covered by the warranty:
Costs for transportation, brokerage or export duties.
Labor costs for removal and reinstallation.
Costs for service calls to diagnose problems.
Discoloration of stainless steel parts.
Part failure due to lack of cleaning and maintenance, or use of improper cleaners (oven cleaner).
www.ultrachefgrills.com
26
Caution! During unpacking and assembly we recommended you wear work gloves and safety glasses
for your protection. Although we make every effort to make the assembly process as problem free and
safe as possible, it is characteristic of fabricated steel parts that the edges and corners might be sharp and
could cause cuts if handled incorrectly.
ATTENTION! Lors du déballage et de l’assemblage, nous vous conseillons de porter des gants
de travail et des lunettes de sécurité pour votre protection. Malgré tous nos efforts pour assurer que
l’assemblage soit aussi sécuritaire et sans problème que possible, il se peut que les bords et les coins des
pièces usinées en acier soient coupants et qu’ils causent des coupures si les pièces ne sont pas manipulées
correctement.
Getting Started
1. Remove all cart panels, hardware, and grill head from carton. Raise lid and remove any components
packed inside. Use the parts list to ensure all necessary parts are included.
2. Do not destroy packaging until the grill has been fully assembled and operates to your satisfaction.
3. Assemble the grill where it is to be used, lay down cardboard or a towel to protect parts from being lost or
damaged while assembling.
4. Most stainless steel parts are supplied with a protective plastic coating that must be removed prior to using grill.
5. Follow all instructions in the order that they are laid out in this manual.
6. Two people are required to lift the grill head onto the assembled cart.
If you have any questions about assembly or grill operation, or if there are damaged or missing parts please
call our Customer Care Department at 1-866-820-8686 between 9 AM and 5 PM (Eastern Standard Time).
Pour Commencer
1. Retirez tous les panneaux, le matériel et le gril du carton d’emballage. Soulevez le couvercle et enlevez les
composants qui se trouvent à l’intérieur. Servez-vous de la liste de pièces pour vous assurer que toutes les
pièces nécessaires sont incluses.
2. Ne détruisez pas l’emballage jusqu’à ce que le gril ait été complètement assemblé et qu’il fonctionne à
votre satisfaction.
3. Assemblez le gril là où il sera utilisé et posez un carton ou une serviette afin d’éviter de perdre ou
d’endommager les pièces lors de l’assemblage.
4. La plupart des pièces en acier inoxydable possèdent un revêtement de plastique protecteur qui doit être
enlevé avant d’utiliser le gril.
5. Suivez toutes les instructions dans l’ordre donné dans ce manuel.
Deux personnes sont requises pour soulever la cuve de gril et la placer sur le chariot assemblé.
Si vous avez des questions à propos de l’assemblage ou du fonctionnement du gril, ou si des pièces sont
manquantes ou endommagées, veuillez appeler notre département du Service aux Consommateurs au
1-866-820-8686 entre 9 h et 17 h (heure normale de l’Est).
TOOLS REQUIRED FOR ASSEMBLY (tools not included)
OUTILS REQUIS POUR L’ASSEMBLAGE (outils non inclus)
3/8 (10mm)
Wrench,
ratchet or driver
Tournevis ou clé,
cliquet de 3/8
(10mm)
www.ultrachefgrills.com
Flat and Philips
screwdrivers
Tournevis plat et
phillips
Pliers
Hammer
Pinces
Marteau
27
Cart model only
Modèle sur chariot seulement
8 X N570-0027 (#14 x 2”)
3/8”(10mm)
Cart model only
Modèle sur chariot seulement
www.ultrachefgrills.com
28
Cart model only
Modèle sur chariot seulement
8 x N570-0026 (#14 x 1/2”)
3/8”(10mm)
Two people are required
for this step.
Deux personnnes son
nécessaires pour cette
étappe.
Cart model only
Modèle sur chariot seulement
2 x N570-0026 (#14 x 1/2”)
3/8”(10mm)
1 x N570-0065
Propane Only
Propane Seulement
www.ultrachefgrills.com
29
Pedestal model only
Modèle sur socle seulement
4 x N570-0026 (#14 x 1/2”)
3/8”(10mm)
Propane Only
Propane Seulement
Pedestal model only
Modèle sur socle seulement
www.ultrachefgrills.com
30
Pedestal model only
Modèle sur socle seulement
If necessary the side panel can be tapped down with
a rubber mallet.
Si nécessaire, le panneau lateral peut être enfoncé
avec un maillet en caoutchouc.
Pedestal model only
Modèle sur socle seulement
4 x N570-0026 (#14 x 1/2”)
www.ultrachefgrills.com
3/8”(10mm)
31
Pedestal model only
Modèle sur socle seulement
2 x N570-0026 (#14 x 1/2”)
3/8”(10mm)
Propane Only
Propane Seulement
Pedestal model only
Modèle sur socle seulement
4 x N570-0026 (#14 x 1/2”)
3/8”(10mm)
Two people are required
for this step.
Deux personnnes son nécessaires
pour cette étappe.
www.ultrachefgrills.com
32
Cart model only
Modèle sur chariot seulement
2 x N570-0029 (1/4-20 X 3/8”)
2 x N570-0036 (1/4-20 X 1”)
2 x N570-0026 (#14 x 1/2”)
Optional locking screw.
Vis de verrouillage optionnelle.
www.ultrachefgrills.com
Push brackets to end of slots.
Enfoncez les supports
jusqu’au fond des fetes.
3/8”(10mm)
33
Pedestal model only
Modèle sur socle seulement
5 x N570-0076 (#8 X1/2”)
Pedestal model only
Modèle sur socle seulement
2 x N570-0026 (#14 x 1/2”)
Optional locking screw.
Vis de verrouillage optionnelle.
Twist tab to lock
in place.
Tournez la patte
pour verrouiller.
www.ultrachefgrills.com
34
2 x N450-0005 (10-24)
2 x N305-0041
2 x N305-0065
www.ultrachefgrills.com
35
1 x N520-0011K
1 x N160-0010
1 x N185-0001
www.ultrachefgrills.com
36
2 x N160-0002
Propane Only – Proper Hose Connection
Propane Seulement - Branchement Adéquat Du Boyau
Pedestal model
Modèle sur socle
Ensure bushing
snaps into side
panel as shown.
Cart model
Modèle sur chariot
Ensure that the hose
leading to the gas
supply runs in front
of the leg.
Assurez-vous que le
boyau de menant à
l’alimentation en gaz
passe en avant de la
patte.
Assurez-vous
que la bague soit
insérée dans le
panneau latéral
tel qu’illustré.
WARNING! Ensure the hose does not contact any high temperature surfaces, or it may melt and leak
causing a fire.
AVERTISSEMENT! Assurez-vous que le boyau ne touche à aucune surface à haute température
sinon il risque de fondre, de provoquer une fuite et causer un feu.
Natural Gas Only – Proper Hose Connection
Gaz Naturel Seulement - Branchement Adéquat Du Boyau
WARNING! The installation must be performed by a licensed gas fitter, and all connections must
be leak tested before operating the grill.
AVERTISSEMENT! L’installation doit être effectuée par un installateur certifié pour le gaz et tous les
raccordements doivent être testés pour des fuites avant de faire fonctionner le gril.
Pedestal model
Modèle sur socle
Cart model
Modèle sur chariot
Ensure that the hose
leading to the gas supply
runs in front of the leg.
Assurez-vous que le boyau
de menant à l’alimentation
en gaz passe en avant de
la patte.
www.ultrachefgrills.com
37
Propane Only – Improper Hose Connection
Propane Seulement – Branchement Inadéquat Du Boyau
WARNING – FIRE HAZARD
ATTENTION - RISQUE D’INCENDIE
WARNING! Do not route hose over top of front panel.
AVERTISSEMENT! N’acheminez pas le boyau par-dessus le panneau avant.
WARNING! Ensure the hose does not contact any high temperature surfaces, or it may melt and leak
causing a fire.
AVERTISSEMENT! Assurez-vous que le boyau ne touche à aucune surface à haute température
sinon il risque de fondre, de provoquer une fuite et causer un feu.
www.ultrachefgrills.com
38
Natural Gas Only – Improper Hose Connection
Gaz Naturel Seulement - Branchement Inadéquat Du Boyau
WARNING – FIRE HAZARD
ATTENTION - RISQUE D’INCENDIE
WARNING! Do not route hose over top of front panel.
AVERTISSEMENT! N’acheminez pas le boyau par-dessus le panneau avant.
Pedestal model
Modèle sur socle
Cart model
Modèle sur chariot
WARNING! Do not route hose underneath drip pan.
AVERTISSEMENT! Ne pas passer le tuyau d’alimentation sous le tiroir d’égouttement afin de garder.
WARNING! Ensure the hose does not contact any high temperature surfaces, or it may melt and leak
causing a fire.
AVERTISSEMENT! Assurez-vous que le boyau ne touche à aucune surface à haute température
sinon il risque de fondre, de provoquer une fuite et causer un feu.
www.ultrachefgrills.com
39
Leak Testing Instructions
WARNING! A leak test must be performed annually and each time a cylinder is hooked up or if a part
of the gas system is replaced.
Warning! Never use an open flame to check for gas leaks. Be certain no sparks or open flames are
in the area while you check for leaks. Sparks or open flames will result in a fire or explosion, damage to
property, serious bodily injury, or death.
Leak testing: This must be done before initial use, annually, and whenever any gas components are replaced
or serviced. Do not smoke while performing this test, and remove all sources of ignition. See Leak Testing
Diagram for areas to check. Turn all burner controls to the off position. Turn gas supply valve on.
Brush a half-and-half solution of liquid soap and water onto all joints and connections of the regulator, hose,
manifolds and valves.
Bubbles will indicate a gas leak. Either tighten the loose joint or have the part replaced with one recommended by the Customer Care department and have the grill inspected by a certified gas installer.
If the leak cannot be stopped, immediately shut off the gas supply, disconnect it, and have the grill inspected
by a certified gas installer or dealer. Do not use the grill until the leak has been corrected.
www.ultrachefgrills.com
41
Parts List / Liste Des Pièces
ITEM PART #
DESCRIPTION
U405 U405RB UP405RB
1
2
3
4
5
6
7
8
9
10
11
lid casting / moulage du couvercle
lid insert / couvercle
temperature gauge / jauge de température
lid handle / poignèe du couvercle
lid pivot screw / vis du pivot
electronic ignition / allumeur électronique
warming rack / grille - réchaud
rear burner cover (infra red) / boîter du brûleur arrière (infra-rouge)
rear burner / brûleur arrière
rear cover / boîter arrière
cooking grill / grille de cuisson
cooking grill stainless steel / grille de cuisson acier inoxydable
sear plate left and right / plaque de brûleur gauche et droite
main burner left and right / brûleur principal gauche et droite
main burner centre / brûleur principal centrale
collector box - main burner / boîte du collecteur du brûleur principal
main burner electrode / électrode du brûleur principal
base casting / cuve
base mounting brackets / supports de la cuve
heatshield / pare chaleur
stainless steel side shelf, left / tablette latérale en acier inoxydable, gauche
luxidio side shelf end cap, left / embout en luxidio de le tablette latéral, gauche
#8 x 1/2” screw / #8 x 1/2” vis
stainless steel side shelf, right / tablette latérale en acier inoxydable, gauche
luxidio side shelf end cap, right / embout en luxidio de le tablette latéral, gauche
#8 x 1/2 screw / #8 x 1/2 vis
top tank support / support supérieur de la bonbonne
thumbscrew 1/4-20 / vis 1/4-20
control panel / panneau de contrôle
control panel / panneau de contrôle
shoulder screw #14 x 1/2”” / vis #14 x 1/2
control knob bezel / monture de bouton de commande
control knob / bouton de contrôle
manifold assembly / ensemble du collecteur
manifold assembly / ensemble du collecteur
manifold assembly / ensemble du collecteur
manifold assembly / ensemble du collecteur
grease tray holder / support du récipient à graisse
5 replacement grease trays / ensemble de 5 récipient à graisse
leg / patte
#14 x 1/2 screw / #14 x 1/2 vis
lower tank support / support inférieur de la bonbonne
wheel - each / roue (unité)
clevis pin / clavette en U
cotter pin / clavette d’arrêt
front cart panel / panneau avant du chariot
bottom shelf / tablette du bas
#14 x 2 screw / #14 x 2 vis
caster assembly - each / ensemble de roulettes (unité
axle / essieu
tank support / support du bonbonne
axle cap / enjoliveur
bottom shelf / tablette du bas
#14 x 1/2 screw / #14 x 1/2 vis
pedestal, right side / socle droite
pedestal, left side / socle gauche
pedestal, front / socle avant
Ultra Chef logo / logo Ultra Chef
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
ac
x
x
x
x
x
x
x
x
x
ac
x
x
x
x
x
x
x
x
x
p
p
x
x
p
p
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29a
29b
29c
29d
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
n135-0027p
n335-0031
n685-0007
n325-0051uc
n570-0056
n357-0013
n520-0011k
n200-0056
n100-0027
n200-0055p
n305-0065
n370-0520
n305-0041
n100-0021
n100-0022
n350-0054
n240-0016
n135-0029p
n080-0111p
n585-0018p
n590-0159
n120-0004
n570-0076
n590-0163
n120-0005
n570-0008
n080-0019p
n570-0065
n475-0201
n475-0202
n570-0028
n051-0006
n380-0017
n010-0333
n010-0334
n010-0335
n010-0336
n160-0010
62007
n075-0074p
n570-0026
n080-0124
n745-0007
n485-0011
n485-0012
n475-0119
n590-0095p
n570-0027
n370-0053
n015-0002
n010-0360p
n450-0023
n010-0359p
n570-0026
n495-0020p
n495-0019p
n495-0021
n385-0186
x
x
x
x
x
x
x
x
x
x
x
ac
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
ac
x
x
p
x
x
x
x
x
x
x
p
n
x
ac
x
x
p
x
x
x
x
x
x
x
p
n
x
ac
x
x
x
x
x
p
n
x
x
x
x
p
x
x
x
x
x
x
x
www.ultrachefgrills.com
42
Parts List / Liste Des Pièces
ITEM PART #
DESCRIPTION
50
51
52
53
54
55
56
57
58
tank heatshield / écran de chaleur
hose clip / support de tuyau
Solido side shelf / tablette latérale en Solido
side shelf bracket - right / support de la tablette latérale - droite
side shelf bracket - left / support de la tablette latérale - gauche
towel bar / support du crochet
1/4-20 x 1 screw / 1/4-20 x 1 vis
1/4-20 x 3/8 screw / 1/4-20 x 3/8 vis
burner grease shield/pare chaleur brûleur
rear burner supply tube / tuyau d’alimenation brûleur arrière
1-outlet regulator / ensemble de tuyau de régulateur à 1 sortie
1-outlet regulator / tuyau de régulateur à 1 sortie
16”” side burner hose / tuyau brûleur latérale de 16””
10ft n/g hose w/quick disconnect / tuyau de 10 pieds avec débranchement rapide
20”” side burner hose / tuyau brûleur latérale de 20””
rotisserie kit / ensemble de la rôtissoire
vinyl cover / housse en vinyle
n585-0023p
n160-0002
n590-0049
n080-0113p
n080-0112p
n030-0001p
n570-0036
n570-0029
n200-0054
n720-0035
n530-0003
n530-0005
n345-0009
n345-0001
n345-0002
64405
63161
U405 U405RB UP405RB
p
x
x
x
x
x
x
x
x
p
x
x
x
x
x
x
x
x
p
n
n
ac
ac
ac
ac
x - standard
p - propane units only
x - compris
n - natural gas units only n - appareils gaz naturel seulement
ac - accessory
www.ultrachefgrills.com
p - appareils propane seulement
ac - accessoires
x
x
p
ac-p
n
ac-n
ac
ac
43
www.ultrachefgrills.com
44
FAX TO: 705 727 4282
ACCESSORIES & PARTS ORDER FORM
PLEASE PRINT CLEARLY
CONTACT NAME:______________________________________________________________________
SHIP TO :_____________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
TEL :_________________________________
FAX :______________________________
EMAIL: __________________________________________________________________
VISA OR MASTERCARD # :_______________________________________ EXPIRY DATE: _____________
SIGNATURE:_____________________________________________________________________________
QUANTITY
PART NUMBER
DESCRIPTION
TAXES MAY APPLY
SHIPPING EXTRA
IF CONFIRMATION IS REQUIRED PLEASE INCLUDE A FAX NUMBER OR EMAIL ADDRESS
www.ultrachefgrills.com
46
www.ultrachefgrills.com
47
www.ultrachefgrills.com