MULTIQUIP MVC-HW Specifications

OPERATION AND PARTS MANUAL
SERIES
MODEL MVC-70H/HW
ONE-WAY PLATE COMPACTOR
(HONDA GASOLINE ENGINE)
Revision #2 (11/02/05)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PROPOSITION 65
l
PAGE 2 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
NOTE PAGE
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 3
TABLE OF CONTENTS
Multiquip MVC-70H/HW
Plate Compactor
Proposition 65 ........................................................... 2
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Specifications ............................................................ 6
Dimensions ............................................................... 7
Safety Message Alert Symbols .............................. 8-9
Rules For Safe Operation.....................................10-11
Operation and Safety Decals .................................. 12
General Information ................................................ 13
Components (Plate Compactor) ............................. 14
Components (Engine) ............................................. 15
Inspection ........................................................... 16-17
Initial Start-Up/Operation ................................... 18-19
Maintenance ...................................................... 20-21
Preparation For Long Term Storage ....................... 22
Troubleshooting (Engine) ................................... 23-24
Troubleshooting (Plate Compactor) ........................ 25
Explanation Of Codes In Remarks Column ............ 26
Suggested Spare Parts ........................................... 27
Honda GX160K1QMX2 Engine
Cylinder Head Assembly ....................................38-39
Cylinder Barrel (Recoil) Assembly .....................40-41
Crankcase Cover Assembly ...............................42-43
Crankshaft Assembly .........................................44-45
Piston/Connecting Rod Assembly ......................46-47
Camshaft Assembly ...........................................48-49
Recoil Starter .....................................................50-51
Fan Cover Assembly ..........................................52-53
Carburetor Assembly .........................................54-55
Air Cleaner Assembly.........................................56-57
Muffler Assembly ...............................................58-59
Fuel Tank Assembly ...........................................60-61
Flywheel Assembly ............................................62-63
Ignition Coil Assembly ........................................64-65
Control Assembly ...............................................66-67
Gasket Assembly ...............................................68-69
Label Assembly ..................................................70-71
Terms and Conditions Of Sale — Parts .................. 72
Component Drawings
Name Plate and Decals ..................................... 28-29
Main Body Assembly (Old Style)........................ 30-31
Main Body Assembly (New Style) ...................... 32-33
Vibrator Assembly .............................................. 34-35
Water Tank ......................................................... 36-37
l
NOTE
NOTE
Specification and part number
are subject to change without
notice.
As a continuing effort to
update our parts book, contact
the MULTIQUIP literature
department for the latest
revision of your "Operation
and Parts Manual"
PAGE 4 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
www.multiquip.com
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only):
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
parts@multiquip.com.
Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
NOTE
❒
Specify Preferred Method of Shipment:
✓ Fed Ex/UPS
✓ DHL
✓ Truck
■ Priority One
■ Ground
■ Next Day
■ Second/Third Day
Unless otherwise indicated by customer, all orders are treated as Standard Orders and will ship
within 24 hours. We will make every effort to ship Air Shipments the same day the order is received,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
WE ACCEPT ALL MAJOR CREDIT CARDS!
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 5
MVC-70H/HW — SPECIFICATIONS
TABLE 1. COMPACTOR SPECIFICATIONS
Model
MVC-70H/W
Centrifugal Force
1,220 kg (2,700 lbs.)
Vibration Frequency
5,600 vpm (93 Hz)
Maximum Forward Speed
25 m/min (82 ft/min)
Plate Size (L x W)
541 x 350 mm (21.3 x 13.8 in )
Overall Dimensions (L x W x H)
879 x 350 x 886 mm (4.6 x 13.8 x 34.9 in )
Operating Weight (with water tank)
86 kg (190 lbs.)
Operating Weight (without water tank)
76 kg (168 lbs.)
Maximum Area of Compaction
543 sq. m/hr (5,865 sq. ft/hr)
Water Tank Capacity (0ption)
10 liters (2.64 gallons)
Table 2. Specifications (Engine)
l
Engine
Model
HONDA GX160K1QMX2
Type
Air-cooled 4 stroke, Single
Cylinder, OHV, Horizontal
Shaft Gasoline Engine
Bore X Stroke
2.4 in. x 1.7 in.
(60 mm x 42 mm)
Displacement
119 cc (7.2 cu-in)
Max Output
Fuel Tank Capacity
Fuel
Lube Oil Capacity
4.0 H.P./3600 R.P.M.
0.66 US gal. (2.5 liters)
Unleaded Automobile
Gasoline
.60 liters (0.63 qts)
Speed Control
Method
Centrifugal Fly-weight Type
Star ting Method
Recoil Star t
Dimension
(L x W x H)
11.7 x 13.4 x 12.5 in.
(297 x 341 x 318 mm)
Dr y
Net Weight
28.7 lbs (13 Kg.)
PAGE 6 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — DIMENSIONS
Figure 1. MVC-70H/HW Plate Compactor Dimensions
TABLE 3. DIMENSIONS
REFERENCE LETTER
A
B
C
D
E
F
DESCRIPTION
Height (Handle Upright)
Width
Length (Handle Upright)
Plate Length
Length (Handle Lowered)
Height (Compactor Only)
Shipping Dimensions
DIMENSION in. (mm)
914 mm (36 in).
420 mm (16.5 in.
635 mm (25 in.)
510 mm (20 in).
914 mm (36 in).
635 mm (25 in.)
686 x 381 x 711 mm
( 27 x 15 x 28 in.)
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 7
MVC-70H/HW — SAFETY MESSAGE ALERT SYMBOLS
FOR YOUR SAFETY AND THE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed at all times when operating
this equipment. Failure to read and understand the Safety
Messages and Operating Instructions could result in injury to
yourself and others.
Potential hazards associated with the operation of the MQ
Model MVC-70H/HW Plate Compactor. will be referenced
with Hazard Symbols which appear throughout this manual,
and will be referenced in conjunction with Safety Message
Alert Symbols.
NOTE
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the MQ Model
MVC-70H/HW Plate Compactor.
Refer to the engine manufacturers
instructions for data relative to its
safe operation.
Before using this plate compactor, ensure that the
operating individual has read and understands all
instructions in this manual.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform
you about potential hazards that could injure you or others.
The Safety Messages specifically address the level of
exposure to the operator, and are preceded by one of
three words: DANGER, WARNING, or CAUTION.
DANGER
You WILL be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
WARNING
l
You CAN be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
CAUTION
CAUTION
WARNING - Lethal Exhaust Gas Hazards
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide ample free flow
air.
DANGER - Explosive Fuel Hazards
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
WARNING - Burn Hazards
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
You CAN be INJURED if you DO NOT follow directions.
WARNING - Respiratory Hazards
ALWAYS wear approved respiratory
protection when required.
PAGE 8 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — SAFETY MESSAGE ALERT SYMBOLS
CAUTION - Rotating Parts Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
CAUTION - Accidental Starting Hazards
ALWAYS place the power source, circuit
breakers or ON/OFF switch in the OFF
position, when the generator is not in use,
unless connected to transfer switch.
CAUTION - Eye and Hearing Hazards
ALWAYS wear approved eye and
hearing protection.
CAUTION - Equipment Damage Hazards
Other important messages are provided throughout this
manual to help prevent damage to your light tower, other
property, or the surrounding environment.
WARNING - Read Manual
Before attempting to operate
the plate compactor, and to
avoid serious injury to
personnel, always read and
understand operation manual.
Failure to read and understand
operation manual
could
result in serious harm or even
death!
DANGER - Refueling Hazard
DO NOT refuel plate compactor if compactor is placed
inside truck bed with PLASTIC LINER. Possibility exists
of explosion or fire due to static electricity.
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 9
MVC-70H/HW — RULES FOR SAFE OPERATION
CAUTION - Read Manual!
Failure to follow instructions in this
manual may lead to serious injury or
even death! This equipment is to be
operated by trained and qualified
personnel only! This equipment is for
industrial use only.
The following safety guidelines should always be used when
operating the MQ Mikasa Model MVC-70H/HW Plate
Compactor.
GENERAL SAFETY
■ DO NOT operate or service this equipment before reading
this entire manual.
■ This equipment should not be operated by persons under
18 years of age.
■ NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■ NEVER operate this equipment when not
feeling well due to fatigue, llness or taking
medicine.
■ NEVER operate this equipment under the
influence of drugs or alcohol.
l
■ NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or compactor.
■ High Temperatures – Allow the
engine to cool before adding fuel or
performing service and maintenance functions. Contact
with hot! components can cause serious burns.
■ The engine section of this compactor requires an adequate
free flow of cooling air. NEVER operate the compactor
in any enclosed or narrow
area where free flow of the
air is restricted. If the air
flow is restricted it will
cause serious damage to
the compactor or engine
and may cause injury to
people. Remember the
plate compactor's engine
gives off DEADLY carbon monoxide gas.
■ ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■ ALWAYS use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it to
cool. DO NOT smoke around or near the
machine. Fire or explosion could result
from fuel vapors, or if fuel is spilled on a
hot engine.
■ NEVER operate the plate compactor in
an explosive atmosphere or near
combustible materials. An explosion or
fire could result causing severe bodily
harm or even death.
■ ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment when
operating the plate compactor.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ Topping-off to filler port is dangerous, as it tends to spill
fuel.
■ Manufacture does not assume responsibility for any
accident due to equipment modifications.
Equipment should be stored in a clean, dry location out of the
reach of children.
■ Maintain this equipment in a safe operating condition at
all times.
■ ALWAYS store equipment properly when it is not being used.
■ NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
PAGE 10 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — RULES FOR SAFE OPERATION
■ NEVER run engine without air filter. Severe engine damage
may occur.
■ ALWAYS service air cleaner frequently to prevent carburetor
malfunction.
■ ALWAYS be sure the operator is familiar with proper safety
precautions and operations techniques before using
compactor.
■ ALWAYS read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■ Refer to the Honda Engine Owner's Manual for engine
technical questions or information.
Loading and Unloading (Crane)
■ Before lifting, make sure that machine parts (lifting bale and
vibration insulator) are not damaged and screws are not
loosened or lost.
■ ALWAYS make sure crane or lifting device has been properly
secured to the lifting bale on the compactor.
TRANSPORTING
■ ALWAYS shutdown engine before transporting.
■ Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
■ Drain fuel when transporting compactor over long
distances or bad roads.
MAINTENANCE
■ NEVER lubricate components or attempt service on a
running compactor.
■ ALWAYS allow the plate compactor a proper amount of
time to cool before servicing.
■ Keep the compactor in proper running condition.
■ Fix damage to the plate compactor immediately and
always replace broken parts.
■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
■ DO NOT use food or plastic containers to dispose of
hazardous waste.
EMERGENCIES
■ ALWAYS know the location of the nearest fire
extinguisher and first aid kit.
■ NEVER lift the compactor while the engine is running.
■ Use adequate lifting cable (wire or rope) of sufficient strength.
■ Use one point suspension hook and lift straight upwards.
■ NEVER allow any person or animal to stand underneath the
machine while lifting.
■ In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■ Try not to lift compactor to unnecessary heights.
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 11
MVC-70H/HW — OPERATION AND SAFETY DECALS
Machine Safety Decals
The MVC-70H/HW Plate Compactor is equipped with a number of safety decals (Figure 2). These decals are provided for operator
safety and maintenance information. The illustration below shows these decals as they appear on the machine. Should any of these
decals become unreadable, replacements can be obtained from your dealer.
l
Figure 2. Operation and Safety Decals
PAGE 12 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — GENERAL INFORMATION
Definition of Plate Compactor
Frequency/Speed
The Mikasa MVC-70H/HW is a walk behind, plate compactor
designed for the compaction of sand, mixed soils and asphalt.
This plate compactor is a powerful compacting tool capable of
applying a tremendous force in consecutive high frequency
vibrations to a soil surface. Its applications include compacting
for road, embankments and reservoirs as well as backfilling for
gas pipelines, water pipelines and cable installation work.
The compactor's vibrating plate has a frequency of 5,600 vpm
(vibrations per minute). The travel speed of the compactor is
approximately 82 ft./minute (25 meters/minute).
The MVC-70H/HW is small and lightweight. It can be easily
handled by one person in confined areas. It has an accessible
front-mounted vibrator assembly. The sealed belt cover keeps
dirt and rocks away from the belt.
Controls
Engine
The Mikasa MVC-70H/HW Plate Compactor is equipped with a
Honda GX160K1QMX2 gasoline engine.
Before starting the MVC-70H/HW Plate Compactor identify and
understand the function of the controls and components as
indicated Figure 3.
Vibratory Plate
The vibratory plate of the compactor produces low amplitude
high frequency vibrations, designed to compact granular soils
and asphalt.
The resulting vibrations cause forward motion. The engine and
handle are vibration isolated from the vibrating plate.
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 13
MVC-70H/HW — COMPONENTS (PLATE COMPACTOR)
Figure 3. MVC-70H/HW Plate Compactor Components
Figure 3 shows the location of the components and general
maintenance parts. The function of each component is described
below:
6.
Belt Cover – Remove this cover to gain acess to the Vbelts. NEVER run the compactor without the V-belt cover. If
the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
1.
Water Tank Cap (for MVC-70HW
only) – Remove this
l
cap to add water to the water tank.
2.
Fuel Tank Cap – Remove this cap to add fuel.
7.
3.
Lifting Bail – When lifting of the compactor is required
either by forklift, crane etc., tie rope or chain around this
lifting point.
Vibrating Plate – A flat, open plate made of durable cast
iron construction used in the compacting of soil.
8.
Vibration Case – Encloses the eccentric, gears and
counter weights.
4.
Handle Bar – When operating the compactor use this
handle bar to maneuver the compactor.
9.
5.
Gasoline Engine – This plate compactor uses a HONDA
GX160K1QMX2 HONDA engine. Refer to the HONDA
owner's manual for engine information.
Water Shut-Off Valve (for MVC-70HW only) – Turn this
valve downward to let water flow from the water tank to the
water tube.
10. Water Tank (for MVC-70HW only) – Holds 10.6 quarts
(10 liters) of water, removable no tools required.
PAGE 14 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — COMPONENTS (HONDA GX160K1QMX2 ENGINE)
Figure 4. Engine Controls & Components
5.
Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop
the flow of fuel.
6.
Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
7.
Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
INITIAL SERVICING
The engine (Figure 4) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturer's engine
manual for instructions and details of operation and servicing.
1.
Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
WARNING
Danger - Flammable Fuel
NOTE
Adding fuel to the tank should be done only
when the engine is stopped and has had an
opportunity to cool down. In the event of a fuel
spill, DO NOT attempt to start the engine until
the fuel residue has been completely wiped
up, and the area surrounding the engine is
dry.
2.
Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
3.
Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operations.
4.
Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
Operating the engine without an
air filter, with a damaged air filter,
or a filter in need of replacement
will allow dirt to enter the engine,
causing rapid engine wear.
8.
Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) for
HONDA engine. Clean spark plug once a week.
9.
Muffler – Used to reduce noise and emissions.
Warning - Hot Surface
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operating. NEVER operate the engine with the
muffler removed.
10. Fuel Tank – Holds unleaded gasoline. For additional
information refer to engine owner's manual.
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 15
MVC-70H/HW — INSPECTION
Before Starting
1. Read safety instructions at the beginning of manual.
NOTE
2. Clean the compactor, removing dirt and dust. Particularly, the
bottom of the plate, engine cooling air inlet, carburetor and
air cleaner.
3. Check the air filter for dirt and dust. If the air filter is dirty, blow
through the air filter cartridge from the inside, moving a jet of
dry compressed air up and down until all dust is removed.
Otherwise replace air filter with a new one.
4. Check carburetor for external dirt and dust. Clean with dry
compressed air.
5. Check fastening nuts and bolts for tightness. Loosened
screws or bolts due to vibration, could lead to unexpected
accident.
Engine Oil Check
1. To check the engine oil level, place the plate compactor on
secure level ground with the engine stopped.
2. Remove the filler cap/dipstick from the engine oil filler hole
(Figure 5) and wipe it clean.
The Oil Alert system will
automatically stop the engine
before the engine falls below safe
limits. Always be sure to check
the engine oil level prior to starting
the engine.
Table 4. Oil Type
Season
Temperature
Oil Type
Summer
25°C or Higher
SAE 10W-30
Spring/Fall
25°C~10°C
SAE 10W-30/20
Winter
0°C or Lower
SAE 10W-10
Gasoline Check
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if fuel level is low. If fuel is low, replenish
with unleaded fuel.
Danger - Flammable Fuel
Motor fuels are highly flammable and can
be dangerous if mishandled. DO NOT
smoke while refueling. DO NOT attempt to
refuel the compactor if the engine is hot! ,
running or in the dark.
3. When refueling, be sure to use a strainer for filtration. DO
NOT top-off fuel. Wipe up any spilled fuel.
Vibrator Oil Check
Figure 5. Enginel Oil Dipstick
3. Insert and remove the dipstick without screwing it into the filler
neck. Check the oil level shown on the dipstick.
4. If the oil level is low (Figure 6), fill to the edge of the oil filler
hole with the recommended oil type (Table 4).
UPPER LIMIT
1. Place the MVC-70H/HW plate compactor horizontally on a
flat surface. Make sure the compactor is level when checking
the oil in the vibrator assembly.
2. Check vibrator oil level by removing the plug (vibrator oil gauge)
as shown in Figure 7. The oil level should be up to the oil plug.
If oil is required, replace using only SAE 10W-30 motor oil.
LOWER LIMIT
Figure 6. Engine Oil Dipstick
Figure 7. Vibrator Oil Plug
PAGE 16 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — INSPECTION
2. The V-belt tension is proper if the V-belt bends 10 to 15 mm
(Figure 10) when depressed with finger at midway between
the clutch and vibration pulley shafts.
V-Belt Check
Caution - V-Belt check
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur if your hand (Figure 8) gets caught
between the V-belt and the clutch. Always use safety gloves.
CLUTCH
PULLEY
Figure 10. V-Belt Tension
VIBRATOR
PULLEY
3. A loose V-belt will decrease the power transmission output,
causing reduced compaction and premature wear of the
belt.
4. If the V-belt becomes worn or loose, replace it .
Figure 8. V-Belt Hazard
1. To check the V-belt tension, remove the bolts that secure the
belt cover to the frame as shown in Figure 9.
Figure 9. V-Belt Cover Removal
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 17
MVC-70H/HW — INITIAL START-UP
Caution - Read Manual
NOTE
D
DO NOT attempt to operate the plate compactor
until the Safety, General Information and
Inspection sections of this manual have been
read and thoroughly understood.
1. Place the fuel valve lever (Figure 11) in the "ON" position.
The CLOSED position of the
choke lever enriches the fuel
mixture for starting a COLD
engine. The OPEN position
provides the correct fuel mixture
for normal operation after
starting, and for restarting a
warm engine.
4. Place the throttle lever (Figure 14) halfway between fast
and slow.
Figure 11. Fuel Valve Lever
2. Place the Engine ON/OFF switch (Figure 12) in the "ON"
position.
Figure 14. Throttle Lever
5. Grasp the starter grip (Figure 15) and slowly pull it out. The
resistance becomes the hardest at a certain position, corresponding the compression point. Rewind the rope a little from
that point and pull out sharply.
Caution - Starter Rope
Figure 12. Engine ON/Off Switch
DO NOT pull the starter rope all the way to the end.
3. Place the Choke Lever (Figure
l 13) in the "OPEN" position.
D
DO NOT release the starter rope after pulling. Allow it to
rewind as soon as possible.
Nnnn
Figure 13. Choke Lever
Figure 15. Starter Grip
PAGE 18 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — INITIAL START-UP
6. If the engine has started, slowly return the choke lever
(Figure 13) to the CLOSED position. If the engine has not
started repeat steps 1 through 5.
7. Before the compactor is put into operation run the engine for
3-5 minutes.
8. Check for abnormal engine noises or fuel leaks.
Stopping the Engine
Caution - Stopping Engine
NEVER stop the engine suddenly while working at high
speeds.
1. Place the throttle lever (Figure 14) in slow position, and
listen for the engine speed to decrease.
Operation
CAUTION - Safety Rules
Make sure to follow all safety rules referenced in the safety
section of this manual before operating compactor. Keep work
area clear of debris and other objects that could cause
damage to the compactor or bodily injury.
1. Once the engine has started, move the engine throttle lever
quickly to the fast position.
2. With the throttle lever in the fast position, the engine speed
should be around 2,300 RPM, therefore engaging the centrifugal clutch.
NOTE
Always move the throttle lever
quickly without hesitation, because
increasing the engine speed slowly
causes the clutch to slip.
2. Place the Engine ON/OFF switch (Figure 12) in the "OFF
" position.
3. Place the fuel valve lever (Figure 11) in the "OFF" position.
3. Firmly gasp the compactor's handle bar with both hands , the
compactor will begin moving forward.
4. Slowly walk behind the compactor and be on the lookout for
any large objects or foreign matter that might cause damage
to the compactor or bodily injury.
5. Compactor traveling speed may drop on soils which contain
clay, however there may be cases where traveling speed
drops because the compaction plate does not leave the
ground surface easily due to the composition of the soil. To
rectify this problem do the following:
z Check the bottom plate to see if clay or
equivalent material has been lodged in the plate
mechanism. If so, wash with water and remove.
z Remember the compactor does not work as
efficiently on clay or soils that have a high
moisture content level.
z If the soil has a high moisture level, dry soil to
appropriate moisture content level or carry out
compaction twice.
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 19
MVC-70H/HW — MAINTENANCE
CAUTION - Inspection
CAUTION - Inspection Intervals
These inspection intervals are for operation under normal
conditions. Adjust your inspection intervals based on the
number of hours plate compactor is in use, and particular
working conditions.
Inspection and other services should always be carried out
on hard and level ground with the engine shut down.
Inspection and Maintenance Service Tables.
1. To make sure your plate compactor is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 5 through 7.
CAUTION - Inspection Intervals
Fuel piping and connections should be replaced every 2
years.
TABLE 5. MVH-64H MACHINE INSPECTION
Daily Service
z Check for leakage of fuel or oil.
ITEM
HOURS OF
OPERATION
Damaged Parts
Every 8 hours
(every day)
z Check engine oil, see page 16.
Loose or Lost Screws
Every 8 hours
(every day)
z Check for loose screws including tightness. See Table 7
below (tightening torque ), for retightening:
REMARKS
z Remove soil and clean the bottom of compaction plate.
TABLE 7.
Function of Controlling Every 8 hours
System Part
(every day)
TIGHTENING TORQUE (in. kg/cm) Diameter
Vibrator Oil Check
Every 100 hours
See page 16
Vibrator Oil
Replacement
Every 300 hours
See page 22
V-belt (clutch) Check
Every 200 hours
See page 17
Material
6mm
8mm
10mm 12mm 14mm 16mm 18mm 20mm
4T
70
150
300
500
750
1,100
1,400
2,000
6-8T
100
250
500
800
1,300
2,000
2,700
3,800
11T
150
400
800
1,200
2,000
2,900
4,200
5,600
*
100 (6mm) 300 ~ 350 (8mm) 650 ~ 700 (10mm)
* (In case counter-part is of aluminum)
(Threads in use with this machine are all right handed)
l
TABLE 6. ENGINE CHECK
(For details, see separate Engine Manual)
Item
Material and quality of material is marked on each bolt,
and screw.
Engine Oil Replacement:
Hours of Operation
Leakage of oil or fuel
Every 8 hours (every day)
Tightness of fastening threads
Every 8 hours (every day)
Engine oil check and replenishment
Every 8 hours (every
day)(Replenish to specified max.
level)
Engine oil replenishment
At first 20 hours, then every 100
hours
Air cleaner cleaning
Every 50 hours
1. Replace engine oil, in first 20 hours of operation and every
100 hours afterwards.
2. Oil may be drained more easily when it is warm after
operation (For more details, see separate HONDA Owner's
Manual).
3. When changing the engine oil, the old oil can be drained by
removing the oil filler cap, and unscrewing the engine oil
drain plug located at the base of the engine (Figure 16).
4. Remember to refill engine crankcase with the recommended
type of oil as listed in Table 4.
PAGE 20 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — MAINTENANCE
Changing Vibrator Oil
1. When changing the vibrator oil, remove the drain plug
(Figure 7), and simply tip the compactor to drain the oil.
Note that the oil will drain more easily while it is hot.
Remember to use only 10W-30 motor oil when replacing
vibrator oil.
Checking and Replacing the V-Belt and Clutch
Figure 16. Engine Oil Plug
Spark Plug
1. Remove and clean the spark plug (Figure 17).
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm). This
unit has electronic ignition, which requires no adjustments.
1. After 200 hours of operation, remove the upper belt cover to
check the V-belt tension. Tension is proper if the belt bends
about 10 mm when depressed strongly with finger between
shafts. Loose or worn V-belts reduces power transmission
efficiency, causing weak compaction and reduces the life of
the belt itself.
WARNING - V-belt Hazard
NEVER attempt to check the V-belt with the engine running.
Severe injury can occur if your hand (Figure 7) gets caught
between the V-belt and the clutch. Always use safety gloves.
CAUTION - Vibration Check
Figure 17. Spark Plug Gap
Whenever the compactor's vibration becomes weak or lost
during normal operation regardless of operation hours, check
the V-belt and clutch immediately.
Air Filter
1. The air filter element should be cleaned because a clogged
air cleaner can cause poor engine starting, lack of power
and shorten engine life substantially.
2. To clean or replace air filter loosen the wing nut on the air
filter housing (Figure 18), remove the cover and take out air
filter cartridge. If only cleaning of the air filter is desired blow
through the air filter cartridge from the inside, moving a jet of
dry compressed air up and down until all dust is removed.
z Replacing the V-belt
Remove the upper and lower belt covers. Engage an offset
wrench (13 mm) or the like to vibrator pulley (lower) fastening
bolt. Engage waste cloth or the like at midway of V-belt on the left
side and while pulling it back strongly, rotate the offset wrench
clockwise so that the V-belt will come off.
z Reinstalling the V-belt
Engage V-belt to lower vibrator pulley and push the V-belt to left
side of upper clutch and, in the same manner as in removal,
rotate offset wrench clockwise so that the V-belt goes back on.
z Checking Clutch
Check the clutch simultaneously with V-belt checking. With belt
removed, check outer drum of the clutch for seizure and "V"
groove for wear or damage with your eyes. Clean the "V" groove
as necessary. Wear of lining or shoe should be checked with
running check. If the shoe is worn, power transmission becomes
deficient and slipping will result.
Figure 18. Air Filter
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 21
MVC-70H/HW — PREPARATION FOR LONG -TERM STORAGE
Compactor Storage
For storage of the compactor for over 30 days, the following
is required:
z Drain the fuel tank completely.
z Run the engine until the fuel in the injection system is
completely consumed.
z Completely drain the oil from the engine crankcase and
follow procedures described in the HONDA engine
Owner's Manual for engine storage.
z Completely drain the compactor's oil from the vibrating
case.
z Clean entire plate compactor, especially the bottom plate
removing all dirt and foreign matter.
z Cover plate compactor and engine with plastic covering
or equivalent and store in a clean, dry place.
l
PAGE 22 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the Troubleshooting Charts (Tables 8 and 9). If
the problem cannot be remedied, please leave the unit just as it is and consult our company's business office or service
plant.
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
Difficult to start, "fuel is available, but no
SPARK at spark plug".
POSSIBLE CAUSE
Spark plug bridging?
Check gap, insulation or replace
spark plug.
Carbon deposit on spark plug?
Clean or replace spark plug.
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Set to proper gap.
ON/OFF switch is shorted?
Check switch wiring, replace
switch.
Ignition coil defective?
Replace ignition coil.
Difficult to star t, "fuel is available, and Improper spark gap, points dirtry?
SPARK is present at the spark plug".
Difficult to start, "fuel is available, spark
is present and compression is normal"
Difficult to start, "fuel is available, spark
is present and compression is low"
No fuel present at carburetor.
SOLUTION
Set correct spark gap and clean
points.
Condenser insulation worn or short
circuiting?
Replace condenser.
Spark plug wire broken or short circuiting?
R e p l a c e d e fe c t i ve s p a r k p l u g
wiring.
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Flush fuel system.
Air cleaner dirty?
Clean or replace air cleaner.
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Piston ring and/or cylinder worn?
Replace piston r ings and or
piston.
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Repl ace head and spar k pl ug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Fuel cock does not open properly?
Appl y l ubr i cant t o l oosen f uel
cock lever, replace if necessary.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Clean or replace fuel tank cap.
Air in fuel line?
Bleed fuel line.
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 23
MVC-70H/HW — TROUBLESHOOTING (ENGINE)
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
"Weak in power" compression is proper
and does not misfire.
POSSIBLE CAUSE
SOLUTION
Air cleaner not clean?
Clean or replace air cleaner
Improper level in carburetor?
Check float adjustment, re-build
carbureator.
Defective Spark plug?
Clean or replace spark plug.
Defective Spark plug?
"Weak in power" compression is proper
but misfires.
Engine overheats.
Rotational speed fluctuates.
Recoil starter malfunction.
Water in fuel system?
Flush fuel system, and replace
with correct type of fuel.
Dirty spark plug?
Clean or replace spark plug.
Ignition coil defective?
Replace ignition coil.
Spark plug heat value improper?
Replace with correct type of
spark plug.
Correct type of fuel?
Replace with correct type of fuel
Cooling fins dirty?
Clean cooling fins.
Governor adjusted correctly?
Adjust governor.
Governor spring defective?
Replace governor spring.
Fuel flow restricted?
Check entire fuel system for leaks
or clogs.
R e c o i l me c h a n i s m c l o g g e d w i t h d u s t a n d
dirt?
Clean recoil assembly with soap
and water.
Sprial spring loose?
Replace sprial spring.
l
PAGE 24 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — TROUBLESHOOTING (PLATE COMPACTOR)
TABLE 9. PLATE COMPACTOR TROUBLESHOOTING
SYMPTOM
Travel speed too low, and vibration is
weak.
Does not travel forward.
POSSIBLE CAUSE
SOLUTION
Engine speed too low?
Set engine speed to correct RPM.
Clutch slips?
Check or replace clutch.
V-belt slips?
Adjust or replace V-belt.
Excessive oil in vibrator?
Drain excess oil and fill to proper level.
Malfunction in vibrator housing?
Check eccentr ic, gears and counter
weights.
V-belt slips?
Replace V-belt.
Clutch slips?
Check clutch springs and shoes.
Vibrator locked?
C h e ck v i b r a t o r h o u s i n g ( e c c e n t r i c,
gears and counterweights)
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 25
MVC-70H/HW — EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and remarks
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
Sample Parts List:
NO.
1
2
2
3
4
REMARKS
INCLUDES ITEMS W/
NOT SOLD SEPARATELY
MQ-45T ONLY
MAKE LOCALLY
S/N 2345B AND ABOVE
*
Unique Symbols - All items with same unique symbol
( , #, +, %, or >) in the number column belong to the same
assembly or kit, which is indicated by a note in the “Remarks”
column.
*
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
PART NO. Column
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
NO. Column
NOTE
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
REMARKS Column
PART NO. PART NAME
QTY.
12345
BOLT ....................... 1....
WASHER, 1/4 IN. ...........
12347
WASHER, 3/8 IN. .... 1....
12348
HOSE .................... A/R ..
12349
BEARING ................ 1....
*
*
QTY. Column
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
l
Numbers Used - Part numbers can be indicated by a number,
a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
“INCLUDES ITEMS W/(unique symbol)”
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
PAGE 26 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — SUGGESTED SPARE PARTS
MQ MIKASA MVC-70H/HW PLATE
COMPACTOR WITH HONDA GX160K1QMX2
GASOLINE ENGINE
1 to 3 Units
Qty.
P/N
Description
3 .......... 070100312 ........... V-BELT
4 .......... 939010250 ........... SHOCK ABSORBER
3 .......... 9807956846 ......... SPARK PLUG
1 .......... 28462ZH8003 ...... ROPE, RECOIL STARTER
3 .......... 17210ZE1505 ....... ELEMENT, AIR CLEANER
1 .......... 17620ZH7023 ...... FUEL CAP
1 .......... 17672ZE2W01 ..... FUEL FILTER, FUEL TANK
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 27
MVC-70H/HW — NAME PLATE AND DECALS
NAME PLATE AND DECALS
l
PAGE 28 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — NAME PLATE AND DECALS
NAMEPLATE AND DECALS
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
PLATE, MODEL/SERIAL NUMBER ..................... 1 ................ CONTACT PARTS DEPT.
2
920203290
DECAL, READ OWNERS MANUAL
1 ................ NPA-329
3
920203989
DECAL, BELT GUARD WARNING
1 ................ NPA-989
4
920101410
DECAL: MIKASA MARK 120X60 ......................... 1 ................ WATER TANK
5
920201580
DECAL: MQ MARK 71X55 ................................... 1 ................ MQ/WATER TANK
6
920105070
DECAL: MIKASA MARK 125MM ......................... 1 ................ WATER TANK
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 29
MVC-70H/HW — MAIN BODY ASSY. (OLD STYLE)
MAIN BODY ASSY. (OLD STYLE)
l
PAGE 30 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — MAIN BODY ASSY. (OLD STYLE)
MAIN BODY ASSY. (OLD STYLE)
NO
PART NO
PART NAME
QTY.
REMARKS
1
418117720
VIBRATORY PLATE .................................. 1 ................. S/N L1643 AND BELOW
2
418216500
BASE ........................................................ 1 ................. S/N L1663 AND BELOW
3
939010250
SHOCK ABSORBER D45-H41
4
4
959404350
EARTH WIRE
1
5
020310080
NUT M10
8
6
030210250
WASHER, LOCK M10
8
7
031110160
WASHER, FLAT M10
4
8
939010010
SHOCK ABSORBER, STOPPER 45 ........ 1 ................. S/N L1643 AND BELOW
9
020310080
NUT M10 ................................................... 1 ................. S/N L1643 AND BELOW
10
030210250
WASHER, LOCK M10 ............................... 1 ................. S/N L1643 AND BELOW
11
912216006
ENGINE HONDA GX160K1QMX2
1
12
404412290
ENGINE NUT ............................................ 1 ................. S/N L1643 AND BELOW
13
413436870
ENGINE NUT, REAR
1
14
002410840
BOLT 8X40 H, SW, PW .............................. 4 ................. S/N L1643 AND BELOW
16
031108160
WASHER, FLAT M8
1
17
022710809
NYLON NUT M8
1
18
404418150
SPACER 18X25X8 CLUTCH
1
19
460446780
CLUTCH ASSY.
1
20
951400100
KEY 5X5X35
1
21
952400130
WASHER 9304
1
22
002210820
BOLT 8X20 H, SW
1
23
070100312
V-BELT RPF-3310
1
25
418216460
BELT COVER ............................................ 1 ................. S/N L1518 AND BELOW
26
002411035
BOLT 10X35 H, SW, PW
1
27
418216480
BELT COVER, IN.
1
28
002411053
BOLT 10X65 SW, PW
1
29
418343420
COVER SEAL, E/G
1
41
413216250
HANDLE LONG
1
45
404433430
RUBBER 20X32X28.5/52H
2
46
952403450
WASHER 11X35X4.5
2
47
002211051
BOLT 10X55 H,SW ................................... 2 ................. S/N L1643 AND BELOW
48
413456490
COLLAR 10.5-20-31.5 ............................... 2 ................. S/N L1643 AND BELOW
49
413436720
RUBBER, HANDLE
2
50
001520845
SOCKET HEAD BOLT 8X45 T
2
51
020308060
NUT M8
2
52
020310080
NUT M10 ................................................... 2 ................. S/N L1643 AND BELOW
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 31
MVC-70H/HW — MAIN BODY ASSY. (NEW STYLE)
MAIN BODY ASSY. (NEW STYLE)
l
PAGE 32 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — MAIN BODY ASSY. (NEW STYLE)
MAIN BODY ASSY. (NEW STYLE)
NO
PART NO
PART NAME
QTY.
REMARKS
1
418117721
VIBRATORY PLATE .................................. 1 ................. S/N L1644 AND ABOVE
2
418216501
BASE ........................................................ 1 ................. S/N L1663 AND ABOVE
3
939010254
SHOCK ABSORBER D45-H41
4
4
959404350
EARTH WIRE
1
5
020310080
NUT M10
8
6
030210250
WASHER, LOCK M10
8
7
031110160
WASHER, FLAT M10
4
1
11
912216006
ENGINE, HONDA GX160K1QMX2
12
418457750
BOLT, ENGINE .......................................... 1 ................. S/N L1644 AND ABOVE
13
413436870
ENGINE NUT, REAR
1
14-1 002410840
BOLT 8X40 H, SW, PW ............................. 2 ................. S/N L1644 AND ABOVE
14-2 030208200
WASHER, LOCK M8 ................................. 2 ................. S/N L1644 AND ABOVE
14-3 031108160
WASHER, FLAT M8 .................................. 2 ................. S/N L1644 AND ABOVE
16
031108160
WASHER, FLAT M8
1
17
022710809
NYLON NUT M8
1
18
408421270
SPACER 20.2X25X9.4, CLUTCH
1
19
413332920
CLUTCH ASSY.
1
20
0053005201
KEY
1
21
952400130
WASHER 9304
1
22-1 001220820
BOLT 8X20 H, SW
1
22-2 030208200
WASHER, LOCK
1
23
070100312
V-BELT RPF-3310
1
25
418216470
BELT COVER ............................................ 1 ................. S/N L1519 AND ABOVE
26-1 001221035
BOLT 10X35 H, SW, PW
1
26-2 030210250
WASHER, LOCK
1
26-3 031110160
WASHER, FLAT
1
27
418216480
BELT COVER, IN.
1
28-1 001221053
BOLT 10X65 SW, PW
1
28-2 030210250
WASHER, LOCK
1
28-3 031110160
WASHER, FLAT
1
29
418343420
COVER SEAL, E/G
1
31
020308060
NUT M8 ..................................................... 2 ................. S/N L1644 AND ABOVE
32
030208200
WASHER, LOCK ....................................... 2 ................. S/N L1644 AND ABOVE
33
031108160
WASHER, FLAT ........................................ 2 ................. S/N L1644 AND ABOVE
41
413216250
HANDLE LONG
1
45
404433430
RUBBER 20X32X28.5/52H
2
46
952403450
WASHER 11X35X4.5
2
47-1 001221020
BOLT 10X20 H,SW ................................... 2 ................. S/N L1644 AND ABOVE
47-2 030210250
WASHER, LOCK M10 ............................... 2 ................. S/N L3696 AND ABOVE
49
413436720
RUBBER, HANDLE
2
50
001520845
SOCKET HEAD BOLT 8X45 T
2
51
020308060
NUT M8
2
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 33
MVC-70H/HW — VIBRATOR ASSY.
VIBRATOR ASSY.
l
PAGE 34 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — VIBRATOR ASSY.
VIBRATOR ASSY.
NO
61
62
63
64
65
66
67
68
69
70
71
72
72
73
74
75
77
78
79
PART NO
418117730
001221445
030214350
031114260
418456950
060403020
418456960
418456970
002400820
418456990
418343400
040306307
040406307
418456980
951401920
952403450
002211030
953400270
953405260
PART NAME
VIBRATING CASE
BOLT 14X45 T
WASHER, LOCK M14
WASHER, FLAT M14
CASE COVER/PULLEY
OIL SEAL TC-30458
CASE COVER/SHUT-OFF
PACKING
BOLT 8X20 SW, PW
COVER SEAL, VIB.
ECC. ROTOR SHAFT
BEARING 6307C3
BEARING 6307C4
PULLEY, VIB.
KEY 7X7X30
WASHER 11X35X4.5
BOLT 10X30 H, SW
PLUG 1/4X14 10L
PACKING
QTY.
1
4
4
4
1
1
1
2
8
1
1
2
2
1
1
1
1
1
1
REMARKS
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 35
MVC-70H/HW — WATER TANK ASSY.
WATER TANK ASSY.
l
PAGE 36 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
MVC-70H/HW — WATER TANK ASSY.
WATER TANK ASSY.
NO
91
92
101
101
102
*
103
*
104
*
105
*
107
108
110
111
112
113
114
115
PART NO
418216510
002211025
418910020
418910030
954300342
001241030
033910010
022910180
954403241
959403790
416338940
418343430
001220825
031108160
020308060
418457010
PART NAME
QTY.
REMARKS
HOOK
1
BOLT 10X25 H, SW
3
WATER TANK, ORANGE ........................... 1 ................. INCLUDES ITEM W/
*
WATER TANK, WHITE ............................... 1 ................. INCLUDES ITEM W/
*
CAP, WATER TANK
1
BOLT 10X30 U
1
WASHER 10.5X21X2 SUS.
2
NYLON NUT M10 SUS.
1
COCK PT1/4, BH-1211 AL.
1
NUT PS-1/4
1
PIPE HOLDER, L
1
SPRINKLING PIPE
1
BOLT 8X25 T
1
WASHER, FLAT M8
2
NUT M8
1
RUBBER CAP
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 37
HONDA GX160K1QMX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
l
PAGE 38 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO. PART NO.
1
12210ZH8000
2
* 12204ZE1306
3
* 12205ZE1315
4 #
12216ZE5300
*
5
12251ZF1800
6
12310ZE1010
7
12391ZE1000
8
15721ZH8000
9
90016ZE1000
10
90043ZE1020
11
90047ZE1000
12
9430110160
14
957230806000
15
9807955846
15
9807956846
PART NAME
QTY. REMARKS
CYLINDER HEAD......................................... 1 ...... INCLUDES ITEMS W/
*
GUIDE, VALVE (OS) (OPTIONAL)
1
GUIDE, EX. VALVE (OS) (OPTIONAL) ........ 1 ...... INCLUDES ITEMS W/#
CLIP, VALVE GUIDE
1
GASKET, CYLINDER HEAD
1
COVER, HEAD
1
GASKET, CYLINDER HEAD COVER
1
TUBE, BREATHER
1
BOLT, FLANGE (6 X 13)
4
BOLT, STUD ( 6 X 109)
2
BOLT, STUD (8 X 32)
2
PIN A, DOWELL (10 X 16)
2
BOLT, FLANGE (8 X 60)
4
SPARK PLUG (BPR5ES) (NGK)
1
SPARK PLUG (BPR6ES) (NGK)
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 39
HONDA GX160K1QMX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
l
PAGE 40 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO. PART NO.
2
12000ZH8811
3
15510ZE1023
3
15510ZE1033
4
16510ZE1000
5#
16511ZE1000
16512ZE1000
6#
8
16531ZE1000
10
90131ZE1000
11
90451ZE1000
12
90601ZE1000
13
90602ZE1000
14
* 91001ZF1003
15
91202883005
*
16
91353671003
17
9405010000
18
9410106800
19
9425108000
20
957010601200
PART NAME
QTY. REMARKS
CYLINDER ASSY. (OIL ALERT) ................... 1 ...... INCLUDES ITEMS W/
*
SWITCH ASSY., OIL LEVEL ........................ 1 ...... USE UP TO ENGINE S/N 4367320
SWITCH ASSY., OIL LEVEL ........................ 1 ...... USE FROM ENGINE S/N 4367321
GOVERNOR ASSY. ...................................... 1 ...... INCLUDES ITEMS W/#
WEIGHT, GOVERNOR
2
HOLDER, GOVERNOR WEIGHT
1
SLIDER, GOVERNOR
1
BOLT, DRAIN PLUG
2
WASHER, THRUST (6MM)
1
WASHER, DRAIN PLUG (10.2MM)
2
CLIP, GOVERNOR HOLDER
1
BEARING, RADIAL BALL (6205)
1
OIL SEAL (25 X 41 X 6)
1
O-RING (13.5 X 1.5) (ARAI)
1
NUT, FLANGE (10MM)
1
WASHER, PLAIN (6MM)
2
PIN, LOCK (8MM)
1
BOLT, FLANGE (6 X 12)
2
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 41
HONDA GX160K1QMX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
l
PAGE 42 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO. PART NO.
1
11300ZE1641
3
11381ZH8801
4
15600ZE1003
5
15600ZG4003
9#
15625ZE1003
15625ZE1003
10+
11
91202883005
*
12
9430108140
13
957010803200
961006205000
14
*
PART NAME
QTY. REMARKS
COVER ASSY., CRANKCASE (U-TYPE) ..... 1 ...... INCLUDES ITEMS W/
*
GASKET, CASE COVER
1
CAP ASSY., OIL FILLER ............................. 1 ...... INCLUDES ITEMS W/#
CAP ASSY., OIL FILLER ............................. 1 ...... INCLUDES ITEMS W/+
GASKET, OIL FILLER CAP
1
GASKET, OIL FILLER CAP
1
OIL SEAL (25 X 41 X 6)
1
PIN A, DOWEL (8 X 14)
2
BOLT, FLANGE (8 X 32)
6
BEARING, RADIAL BALL (6205)
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 43
HONDA GX160K1QMX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
l
PAGE 44 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO. PART NO.
4
13310ZE1601
13
90003ZE1000
14
90473842000
15
90745ZE1600
PART NAME
QTY. REMARKS
CRANKSHAFT (Q-TYPE)
1
BOLT, HEX 5/16” ............................................ 1 .... USE FROM S/N 6745959
WASHER, 8 MM ............................................. 1 .... USE FROM S/N 6745959
KEY, 78 X 38 MM
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 45
HONDA GX160K1QMX2 ENGINE — PISTON/RINGS ASSY.
PISTON/RINGS ASSY.
l
PAGE 46 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — PISTON/RINGS ASSY.
PISTON/RINGS ASSY.
NO. PART NO.
1
13010ZH8941
1
13011ZH8941
1
13012ZH8941
1
13013ZH8941
2
13101ZH8000
2
13102ZH8000
2
13103ZH8000
2
13104ZH8000
3
13111ZE1000
4
13200ZE1010
5
90001ZE1000
* 90551ZE1000
6
PART NAME
QTY.
REMARKS
RING SET, PISTON (STD)
1
RING SET, PISTON (OS 0.25)
1
RING SET, PISTON (OS 0.50) ............. 1 ......... USE FROM ENGINE S/N 4733211
RING SET, PISTON (0.75) OPTION 1
PISTON (STD)
1
PISTON (OS 0.25)
1
PISTON (OS 0.50)
1
PISTON (0.75)
1
PIN, PISTON
1
ROD ASSY., CONNECTING ................ 1 ......... INCLUDES ITEMS W/
*
BOLT, CONNECTING ROD
2
CLIP, PISTON PIN (18MM)
2
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 47
HONDA GX160K1QMX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
l
PAGE 48 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO. PART NO.
1
14100ZE1812
2
14410ZE1010
3
14431ZE1000
4
14441ZE1010
5
14451ZE1013
6
* 14568ZE1000
7
14711ZF1000
8
14721ZF1000
9
14751ZF1000
10
14771ZE1000
11
14773ZE1000
12
14781ZE1000
13
14791ZE1010
14
90012ZE0010
15
90206ZE1000
PART NAME
QTY. REMARKS
CAMSHAFT ASSY. ...................................... 1 ...... INCLUDES ITEMS W/
*
ROD, PUSH
2
ARM, VLAVE ROCKER
2
LIFTER, VALVE
2
PIVOT, ROCKER ARM
2
SPRING, WEIGHT RETURN
1
VALVE, IN.
1
VALVE, EX. (STELITE)
1
SPRING VALVE
2
RETAINER, IN. VALVE SPRING
1
RETAINER, EX. VALVE SPRING
1
ROTATOR, VALVE
1
PLATE, PUSH ROD GUIDE
1
BOLT, PIVOT (8MM)
2
NUT, PIVOT ADJ.
2
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 49
HONDA GX160K1QMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
l
PAGE 50 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO. PART NO.
1
28400ZH8013ZB
2
28410ZH8003ZB
*
3
* 28420ZH8013
4
* 28422ZH8013
5
* 28433ZH8003
6
* 28441ZH8003
7
28442ZH8003
*
8
* 28443ZH8003
9
* 28461ZH8003
28462ZH8003
10
*
11
* 90003ZH8003
12
90008ZE2003
PART NAME
QTY. REMARKS
STARTER ASSY., RECOIL “NH1”(BLACK) ............ 1 ..... INCLUDES ITEMS W/
*
CASE, RECOIL STARTER “NH1”(BLACK)
1
REEL, RECOIL STARTER
1
RATCHET, STARTER
2
GUIDE, RATCHET
1
SPRING, FRICTION
1
SPRING, RECOIL STARTER
1
SPRING, RETURN
2
KNOB, RECOIL STARTER
1
ROPE, RECOIL STARTER
1
SCREW, SETTING
1
BOLT, FLANGE (6 X 10)
3
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 51
HONDA GX160K1QMX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
l
PAGE 52 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO. PART NO.
2
19610ZE1000ZC
4
19612ZH8811
7
90601ZH7013
8
19630ZH8000
11
36100ZE1015
11
36100ZH7003
13
90013883000
14
90022888010
17
34150ZH7003
19
957010600800
PART NAME
QTY.
REMARKS
COVER, FAN *NH1* (BLACK)
1
PLATE, SIDE (OIL ALERT)
1
CLIP, HARNESS
1
SHROUD
1
SWITCH ASSY., ENGINE STOP ........... 1.......... USE UP TO S/N 4368640
SWITCH ASSY., ENGINE STOP ........... 1.......... USE FROM 4368641
BOLT, FLANGE (6 X 12) (CT200)
6
BOLT, FLANGE (6 X 20) (CT200)
1
ALERT UNIT, OIL
1
BOLT, FLANGE (6 X 8)
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 53
HONDA GX160K1QMX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
l
PAGE 54 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO. PART NO.
1
16010ZE1812
16011ZE0005
2
*
3
* 16013ZE0005
4
* 16015ZE0831
5
* 16016ZH7W01
6
* 16024ZE1811
7
16028ZE0005
*
8
* 16044ZE0005
9
* 16100ZH8W51
10
16124ZE0005
*
11
* 16166ZH8W50
12
* 16173001004
13
16211ZE1000
14
16212ZH8800
15
16220ZE1020
16
16221ZH8801
17
16610ZE1000
18
16953ZE1812
*
19
* 16954ZE1811
20
16956ZE1811
*
21
* 16957ZE1812
22
* 16967ZE0811
23
93500030060H
*
24#
9430520122
25
99101ZH80650
25
99101ZH80680
25
* 99101ZH80700
26
99204ZE00350
*
PART NAME
QTY. REMARKS
GASKET SET
1
VALVE SET, FLOAT
1
FLOAT SET
1
CHAMBER SET, FLOAT
1
SCREW SET
1
SCREW SET, DRAIN
1
SCREW SET B
1
CHOKE SET
1
CARBURETOR ASSY. (BE65B B) ................ 1 ...... INCLUDES ITEMS W/
*
SCREW, THROTTLE STOP
1
NOZZLE, MAIN
1
O-RING
1
INSULATOR, CARBURETOR
1
GASKET, INSULATOR
1
SPACER, CARBURETOR
1
GASKET, CARBURETOR
1
LEVER, CHOKE (STD) ................................ 1 ...... INCLUDES ITEMS W/#
LEVER, VALVE
1
PLATE, LEVER SETTING
1
SPRING, VALVE LEVER
1
GASKET, VALVE
1
CUP, FUEL STRAINER
1
SCREW, PAN (3 X 6)
2
PIN, SPRING (2 X 12)
1
JET, MAIN (#65) OPTIONAL
1
JET, MAIN (#68) OPTIONAL
1
JET, MAIN (#70)
1
JET, SET, PILOT (#35)
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 55
HONDA GX160K1QMX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
l
PAGE 56 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER (DUAL) ASSY.
NO. PART NO.
1
16271ZE1000
2
17210ZE1505
3
* 17218ZE1505
4
17230ZE1820
5
* 17232891000
17238ZE7010
6#
7#
17239ZE1000
8
17410ZE1020
9
90201415000
10
17235ze1831
11
90325044000
13
957010602000
PART NAME
QTY. REMARKS
GASKET, ELBOW ........................................ 1 ...... INCLUDES ITEMS W/
*
ELEMENT, AIR CLEANER (DUAL)
1
FILTER (OUTER)
1
COVER, AIR CLEANER (DUAL)
1
GROMMET, AIR CLEANER
1
COLLAR, AIR CLEANER
2
COLLAR B, AIR CLEANER
1
ELBOW, AIR CLEANER ............................... 1 ...... INCLUDES ITEMS W/#
NUT, CAP (6 MM)
2
NOSE, MUFFLER
1
WINGNUT, TOOL BOX SETTING
2
BOLT, FLANGE (6 X 20)
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 57
HONDA GX160K1QMX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
l
PAGE 58 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO. PART NO.
1
18310ZH8810
1
18310ZK8V50
3
18320ZF1H01
5
18331883810
7
18355ZE1000
8
18381ZH8800
11
90050ZE1000
12
90055ZE1000
13
18522ZE1000
15
94001080000S
30
90002ZG0003
PART NAME
QTY. REMARKS
MUFFLER..................................................... 1 ...... USE UP TO S/N 6745959
MUFFLER..................................................... 1 ...... USE FROM S/N 6745959
PROTECTOR, MUFFLER
1
CAP, MUFFLER
1
ARRESTER, SPARK
1
GASKET, MUFFLER
1
SCREW, TAPPING (5 X 8)
4
SCREW, TAPPING (4 X 6)
1
GUIDE, MUFFLER
1
NUT, HEX (8MM)
2
SCREW, TAPPING (4 X 8)
2
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 59
HONDA GX160K1QMX2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
l
PAGE 60 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — FUEL TANK ASSY.
FUEL TANK ASSY.
NO. PART NO.
10
16854ZH8000
17
16955ZE1000
20
17510ZE1020ZF
21
17620ZH7023
23
17631ZH7003
* 17672ZE2W01
24
29
91353671003
33
9405006000
36
950014500360M
40
43
44
45
9500202080
957010602500
90404680000
91319ME5003
PART NAME
QTY. REMARKS
RUBBER, SUPPORTER (107MM)
1
JOINT, FUEL TANK
1
TANK, FUEL *NH1* (BLACK)
1
CAP, FUEL FILLER ...................................... 1 ...... INCLUDES ITEMS W/
*
GASKET, FUEL FILLER CAP
1
FILTER, FUEL
1
O-RING (13.5 X 1.5) (ARAI)
1
NUT, FLANGE (6MM)
2
BULK HOSE, FUEL (4.5 X 3000)
1
(4.5 X 140)
CLIP, TUBE (B8)
2
BOLT, FLANGE (6 X 25)
1
WASHER ...................................................... 2 ...... USE FROM S/N 6745959
O-RING ......................................................... 2 ...... USE FROM S/N 6745959
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 61
HONDA GX160K1QMX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
l
PAGE 62 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO. PART NO.
1
13331357000
2
19511ZE1000
4
28451ZH8003
5
31100ZE1010
5
31100ZE1810
8
90201878003
PART NAME
KEY, SPECIAL WOODRUFF (25 X 18)
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
FLYWHEEL (LAMP)
NUT, SPECIAL (14MM)
QTY.
1
1
1
1
1
1
REMARKS
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 63
HONDA GX160K1QMX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
l
PAGE 64 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO. PART NO.
1
30500ZE1033
2
30700ZE1013
7
36101ZE1010
11
90121952000
PART NAME
COIL ASSY., IGNITION
CAP ASSY., NOISE SUPPRESSOR
WIRE, STOP SWITCH (370MM)
BOLT, FLANGE (6 X 25)
QTY.
1
1
1
2
REMARKS
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 65
HONDA GX160K1QMX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
l
PAGE 66 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO. PART NO.
2
16500ZH8813
4
16551ZE0010
5
16555ZE1000
6
16561ZE1020
7
16562ZE1020
9
* 16571ZH8020
10
16574ZE1000
*
11
* 16575ZH8000
12
* 16576891000
16578ZE1000
13
*
14
* 16580ZH8813
15
* 16584883300
16
* 16592ZE1810
17
* 16594883010
21
90013883000
22
90015ZE5010
24
90114SA0000
* 93500050250H
25
* 90605230000
26
* 93500040060H
27
* 93500050160A
28
* 9405006000
29
PART NAME
QTY. REMARKS
CONTROL ASSY. ......................................... 1 ...... INCLUDES ITEMS W/
*
ARM, GOVERNOR
1
ROD, GOVERNOR
1
SPRING, GOVERNOR
1
SPRING, THROTTLE RETURN
1
LEVER CONTROL
1
SPRING LEVER
1
WASHER, CONTROL LEVER
1
HOLDER, CABLE
1
SPACER, CONTROL LEVER
1
BASE CONTROL
1
SPRING, CONTROL ADJUSTING
1
SPRING, CABLE RETURN
1
HOLDER, WIRE
1
BOLT, FLANGE (6 X 12) (CT200)
2
BOLT, GOVERNOR ARM
1
NUT, SELF-LOCK (6MM)
1
SCREW, PAN (5 X 25)
1
CIRCLIP
1
SCREW, PAN (5 X 25)
1
SCREW, PAN (5 X 16)
1
NUT, FLANGE (6 MM)
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 67
HONDA GX160K1QMX2 ENGINE — GASKET KIT ASSY.
NO ARTWORK AVAILABLE
l
PAGE 68 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — GASKET KIT ASSY.
GASKET KIT ASSY.
NO. PART NO.
1
06111ZH8405
2
11381ZH8801
*
3
* 12251ZF1800
4
* 12391ZE1000
5
* 16212ZH8800
6
* 16221ZH8801
7
18381ZH8800
*
PART NAME
QTY.
REMARKS
GASKET KIT ............................................. 1 .......... INCLUDES ITEMS W/
*
GASKET, CASE COVER
1
GASKET, CYLINDER HEAD
1
GASKET, CYLINDER HEAD COVER
1
GASKET, INSULATOR
1
GASKET, CARBURETOR
1
GASKET, MUFFLER
1
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 69
HONDA GX160K1QMX2 ENGINE — LABELS ASSY.
LABELS ASSY.
l
PAGE 70 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
HONDA GX160K1QMX2 ENGINE — LABELS ASSY.
LABELS ASSY.
NO. PART NO.
1
87521ZH8020
3
87522zh9010
6
87528ZE1810
8
87532ZH8810
PART NAME
EMBLEM (5.5)
LABEL, CAUTION
MARK, CHOKE
MARK, OIL ALERT (E)
QTY.
1
1
1
1
REMARKS
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 71
TERMS AND CONDITIONS OF SALE — PARTS
Effective: October 1, 2002
PAYMENT TERMS
5.
Parts must be in new and resalable
condition, in the original Multiquip package (if any), and with Multiquip part
numbers clearly marked.
6.
The following items are not returnable:
Terms of payment for parts are net 10 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a signed
manifest has been obtained from the carrier,
and any claim for shortage or damage must be
settled between the consignee and the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
Return shipments will be accepted and credit
will be allowed, subject to the following provisions:
1.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers, quantities, and descriptions of the items to be
returned.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
l
c. The list must state the reason(s) for
the return.
d. The list must reference the sales
order(s) or invoice(s) under which the
items were originally purchased.
e. The list must include the name and
phone number of the person requesting the RMA.
3.
A copy of the Return Material Authorization must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
SPECIAL EXPEDITING SERVICE
A $35.00 surcharge will be added to the invoice
for special handling including bus shipments,
insured parcel post or in cases where Multiquip
must personally deliver the parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
d. Special order items.
Multiquip shall not be liable here under for
damages in excess of the purchase price of the
item with respect to which damages are claimed,
and in no event shall Multiquip be liable for loss
of profit or good will or for any other special,
consequential or incidental damages.
e. Electrical components.
LIMITATION OF WARRANTIES
f. Paint, chemicals, and lubricants.
No warranties, express or implied, are made in
connection with the sale of parts or trade accessories nor as to any engine not manufactured
by Multiquip. Such warranties made in connection with the sale of new, complete units are
made exclusively by a statement of warranty
packaged with such units, and Multiquip neither assumes not authorizes any person to
assume for it any other obligation or liability
whatever in connection with the sale of its
products. Apart from such written statement of
warranty, there are no warranties, express,
implied or statutory, which extend beyond the
description of the products on the face hereof.
c. Any line item with an extended dealer
net price of less than $5.00.
RETURNED GOODS POLICY
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
g. Decals and paper products.
h. Items purchased in kits.
7.
The sender will be notified of any
material received that is not acceptable.
8.
Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific date and all orders received on or after
that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
PAGE 72 — MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05)
NOTE PAGE
MVC-70H/HW PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #2 (11/02/05) — PAGE 73
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Tel. (800) 421-1244
Carson, CA 90746
Fax (800) 537-3927
Contact: mq@multiquip.com
Mayco Parts
800-306-2926
Fax: 800-672-7877
310-537-3700
Fax: 310-637-3284
Service Department
800-421-1244
Fax: 310-537-4259
310-537-3700
MQ Parts Department
800-427-1244
310-537-3700
MEXICO
UNITED KINGDOM
MQ Cipsa
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
800-421-1244, Ext. 279 Fax: 310-537-1173
310-537-3700, Ext. 279
Technial Assistance
800-478-1244
Fax: 310-631-5032
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Lancashire OL7 0TL
Contact: sales@multiquip.co.uk
Tel: 0161 339 2223
Fax: 0161 339 3226
CANADA
BRAZIL
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Multiquip
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro
Fax: 011-55-21-3433-9055
Contact: cnavarro@multiquip.com.br, srentes@multiquip.com.br
Tel: (450) 625-2244
Fax: (450) 625-8664
© COPYRIGHT 2005, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MVC-70H/HW Plate
Compactor. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc.
reserves the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any
obligations.
Your Local Dealer is: