ENGLISH Two-Way Radio Model MT 725

Two-Way Radio Model MT 725
ENGLISH
Antenna
External Speaker/
Microphone Jack
LOCK Button
CALL Button
MODE Button
POWER Button
Charge/Intercom Jack
TALK Button
VOLUME CONTROL
Buttons
LIGHT/MAX RANGE
Button
CHANNEL SELECT
Buttons
Speaker/
Microphone
Product Features
• Two-Way Radio
with up to a 3 km (2 mile) range
• 8 Channels*
• 38 CTCSS Privacy Codes
• Backlit LCD Display
• Water Resistant
• Battery Saver Circuitry
• Maximum Range Extender
• VOX Mode for Hands-Free Transmissions
• VibrAlert® Silent Paging
• Baby Monitor Function
• Intercom Capability
• Call Alert (5 Selectable Tones)
• Scan (Channel, Privacy Code)
• Dual Watch Programmable 2-Location Scan
• Key Lock
• Auto Squelch
• Selectable On/Off "Roger Beep"
Confirmation Tone
• Selectable On/Off Keystroke Tone
• External Speaker/Microphone Jack
• Belt Clip
• Wrist Strap
CTCSS Privacy
Code Numbers
Main Channel Number
Lock
Receive/Transmit
Keystroke Tone
Baby Monitor
VibrAlert®/
Call Alert
Scan
Roger Beep
Battery Level Indicator
VOX
Power Saver
Belt Clip
*You are not allowed to use channels 1 and 2 in France.
This situation can change; please contact the French radio licensing
authority for more information.
This equiment is intended for use in:
AT
BE
CY
CZ
DE
DK
•
•
•
•
•
•
EE
ES
FI
FR
GB
GR
•
•
•
•
•
•
• Countries of use
HU
IE
IS
IT
LT
LV
•
•
•
•
•
•
LI
LU
MT
NL
NO
PL
•
•
•
•
•
•
Dual Watch
PT
SE
CH
SI
SK
TR
•
•
•
•
•
•
Battery Compartment
Lock Tab
Wrist Strap Connection
Location
OPERATION
Product Information
English
Radio Power
To Turn Your Radio On:
Power Button
1. Press and hold the POWER
button until you hear a
series of audible tones
indicating that the radio is
On.
Your microTALK® radio is now in LISTENING MODE,
ready to receive transmissions. The radio is always
Caring for Your Radio
in LISTENING MODE, except when the TALK, CALL
®
Your microTALK radio will give you years of
or MODE buttons are pressed.
trouble-free service if cared for properly. Here are a
To Turn Your Radio Off:
few suggestions:
1. Press and hold the POWER button.
• Handle the radio gently.
• Keep it away from dust.
Battery Low Indicator
• Never put the radio in water or in a damp place. Battery power is indicated by
Battery Low
• Avoid exposure to extreme temperatures.
the segments appearing at the
bottom of the display. As
Battery Installation
battery power decreases, fewer
To Install or Replace Batteries:
segments will be visible. When
the last segment begins to flash, the batteries
1. Remove belt clip by
Remove Belt Clip
should be replaced or recharged.
releasing belt clip latch and
sliding clip Up.
WARNING: Only the NiMH battery pack FA-BP can
be recharged.
2. Pull down on the BATTERY
DOOR LOCK TAB to remove
Battery/Power Saver
Lock Tab
the battery compartment
If there are no transmissions
Power Saver
cover.
within ten (10) seconds, the
3. Insert four (4) AAA
unit will automatically switch
batteries. (Always use highThis microTALK® radio has been manufactured to
meet all required standards for radio equipment
using PMR 446 frequencies as authorized. The
use of this two-way radio product involves the
public airways and its use may be subject to local
laws or regulations. Contact your radio licensing
authority for more information.
quality alkaline or recharageable batteries.)
Position batteries according
Insert Batteries
to polarity markings.
4. Replace Battery
Compartment cover and belt
clip.
NOTE: See “Optional Accessories” for accessory
availability and ordering instructions.
to Battery Save Mode and POWER SAVER will
appear in the display. This will not affect the unit’s
ability to receive incoming transmissions.
Communicating with
Another Person
To Talk To Another Person:
1. Press and hold the TALK
Talk Button
button.
Charge/Intercom
Battery Charging
2. With the microphone about
Tab
When the optional NiMH
5 cm (2 inches) from your
battery pack (part No. FA-BP)
mouth, speak in a normal
5 cm (2 Inches)
is used, the batteries can be
voice.
From Mouth
charged using the optional
3. Release the button when
rapid wall mount charger (part Charging Batteries
you have finished talking
No. PA-CW). Simply place the
and listen for a response.
battery pack in the battery
You cannot receive incoming
compartment, open the
calls while pressing the TALK button.
CHARGE/INTERCOM tab on the
side of the unit and insert the plug into the charge NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
jack to start charging. The batteries should be fully
charged in about three (3) hours.
WARNING: Only the NiMH battery pack FA-BP can
be recharged.
NOTE: See “Optional Accessories” for accessory
availability and ordering instructions.
OPERATION
English
Listening for a Response
Display Illumination
When You Have Finished Talking:
1. Release the TALK button to
Listening
receive incoming
transmissions. Your
microTALK® is always in
LISTENING MODE except
when the TALK, CALL or MODE buttons are
pressed.
To Illuminate Your Display:
1. Press and release the
LIGHT/MAX RANGE button
to illuminate the display for
ten (10) seconds.
Volume
Volume Buttons
To Adjust the Volume:
1. Press the VOLUME UP or
the VOLUME DOWN
buttons.
A triple beep sound is used to
indicate that you have reached
the minimum (1) or maximum
(8) volume level.
Volume Level
Call Button
To Alert Another Person That You Are
Calling:
Call Button
1. Press and release the CALL
button.
The other person will hear a
two (2) second ringing tone.
You cannot receive
transmissions while sending a call.
NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
Channels
To Select a Channel:
Channel Buttons
1. With the radio on, select
any of the 8 channels by
pushing the CHANNEL UP or
CHANNEL DOWN button.
You can press and hold the
Channels
CHANNEL UP or CHANNEL
DOWN button for fast advance.
NOTE: Both radios must be
tuned to the same
channel and privacy
code (see “CTCSS Privacy Codes”) to
communicate.
Light/Max Range
Button
Auto Squelch/
Maximum Range Extender
Your microTALK® radio is equipped with Auto
Squelch, which automatically shuts off weak
transmissions and unwanted noise resulting from
terrain, conditions, or from reaching your
maximum range limit.
You can temporarily turn Off Auto Squelch or turn
On Maximum Range Extender, allowing all signals
to be received and extending the maximum range
of your radio.
To Temporarily Turn Off Auto Squelch:
1. Press the LIGHT/MAX
Light/Max Range
Button
RANGE button for less than
five (5) seconds.
If you hear two (2) beeps, you
have turned the Maximum
Range Extender On (see
below).
To Turn Maximum Range Extender On:
1. Press and hold the LIGHT/MAX RANGE button
for at least five (5) seconds until you hear two
(2) beeps, indicating that the Maximum Range
Extender is On.
To Turn Maximum Range Extender Off:
1. Press and release the LIGHT/MAX RANGE
button or change channels.
microTALK® Range
Your microTALK® radio has a range of up to three
(3) kilometres (2 miles). Your range will vary
depending on terrain and conditions.
In flat, open country your
Maximum Range
radio will operate at
maximum range.
Buildings and foliage in the
path of the signal can
Reduced Range
reduce the range.
Dense foliage and hilly
terrain will further reduce
Lock Function
the signal.
The LOCK button locks the CHANNEL UP, CHANNEL Remember, you can achieve
Reduced Range
DOWN, MODE and POWER buttons to prevent
maximum range by using
accidental operation.
Maximum Range Extender.
To Use the Lock Function:
See above for details.
Lock Button
1. Press and hold the LOCK
button for two (2) seconds
to turn the Lock On or Off.
A double beep sound is used to
confirm your Lock On or Off
Lock Icon
request. When the radio is in
Lock Mode, the Lock icon will
be displayed.
OPERATION and
MODE FUNCTIONS
English
External Speaker/ Microphone Jack To Select a Privacy Code:
Your microTALK® radio can be fitted with an
optional external speaker/microphone (not
included), freeing your hands for other tasks.
NOTE: See “Optional Accessories” for accessory
availability and ordering instructions.
External Speaker/
To Attach the External
Microphone
Speaker/Microphone:
1. Open the SPKR/MIC tab on
top of the radio.
2. Insert the plug into the
SPKR/MIC jack.
Intercom
Intercom
With the optional intercom
adapter and two external
speaker/microphone
attachments, a single
microTALK® radio can be used as an intercom
system. (Ideal for motorcyclists.) Contact your
local dealer for availability and pricing.
Scrolling Through the Mode
Functions
By scrolling through the Mode Functions, you will
be able to select or change preferred features of
your microTALK® radio. While you are scrolling
through the Mode Functions, your radio features
will be displayed in the same predetermined order:
Set CTCSS Privacy Codes
Set VOX On/Off
Set VOX Sensitivity Level
Set Channel Scan
Set CTCSS Privacy Code Scan
Set VibrAlert® and/or Call Alert
Set Baby Monitor
Program Dual Watch Location or
Set Dual Watch On/Off
Set Call Tones
Set “Roger Beep” On/Off
Set Keystroke Tones On/Off
1. After selecting a channel,
Mode Button
press and release the MODE
button until the small
numbers next to the
channel number flash on
Select
the display.
Privacy Code
2. Press the CHANNEL UP or
CHANNEL DOWN button to
select a privacy code.
You can press and hold the
CHANNEL UP or CHANNEL
Channel Buttons
DOWN button for fast
advance through CTCSS
privacy code numbers.
3. When your desired privacy
code is displayed, choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for fifteen (15)
seconds to enter the new setting and return
to LISTENING MODE.
Voice Activated Transmit (VOX)
In VOX Mode, your microTALK® radio can be used
“hands-free,” automatically transmitting when you
speak. You can set the VOX sensitivity level to fit
the volume of your voice and avoid transmissions
triggered by background noise.
To Turn VOX Mode On or Off:
1. Press the MODE button until Mode Button
the VOX icon flashes on the
display. The current On or
Off setting is displayed.
2. Press the CHANNEL UP or
Select VOX
CHANNEL DOWN button to
turn VOX On or Off.
3. When your desired VOX
Mode setting is displayed,
choose one of the
CTCSS Privacy Codes
Channel Buttons
following:
CTCSS (Continuous Tone Coded Squelch System)
a. Press the MODE button
is an advanced tone coding system allowing you
to enter the new setting
to select one of 38 privacy codes to reduce
and proceed to other
incoming transmissions from other users on the
functions.
channel.
b. Press the LOCK button to enter the new
NOTE: If you are using a privacy code, both radios
setting and return to LISTENING MODE.
must be tuned to the same channel and
privacy code to communicate. Each channel
c. Do not press any buttons for fifteen (15)
will remember the last privacy code you
seconds to enter the new setting and return
selected.
to LISTENING MODE.
MODE FUNCTIONS
OPERATION
To Set the VOX Sensitivity Level:
1. Press the MODE button until Mode Button
the VOX icon flashes and
the current sensitivity level
is displayed.
The current sensitivity level is
Select VOX
displayed with the letter “L”
Sensitivity Level
and a number 1 to 5, 5 being
the most sensitive level and 1
being the least sensitive level.
2. Press the CHANNEL UP or
Channel Buttons
CHANNEL DOWN button to
change the setting.
3. When your desired VOX
sensitivity level is displayed,
choose one of the
following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for fifteen (15)
seconds to enter the new setting and return
to LISTENING MODE.
Channel Scan
Your microTALK® radio can automatically scan
channels (1 to 8).
NOTE: The radio ignores specific CTCSS privacy
codes while scanning channels.
To Scan Channels:
1. Press the MODE button until Mode Button
the Scan icon and the
channel number flash on
the display.
2. Press the CHANNEL UP or
Select Scan Channels
CHANNEL DOWN button to
begin scanning channels.
The Scan icon will continue to
be displayed when channel
Channel Buttons
scan is On. Your radio will
continue to scan all channels
and stop if an incoming
transmission is detected. Your
radio will remain on that
channel for ten (10) seconds.
While setting channel scan, if you do not press
any buttons for fifteen (15) seconds your radio
will automatically return to LISTENING MODE on
the channel or channel/privacy code displayed
before you entered Mode Functions.
English
During An Incoming Transmission, You
Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that channel. Your radio
will remain on that channel and return to
LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume scanning channels.
If you press the TALK button while scanning and
not within ten (10) seconds of receiving a
transmission, you will transmit on the channel on
which you last received a transmission. This will
return the radio to LISTENING MODE.
If you do not press any button within ten (10)
seconds, your radio will automatically resume
scanning channels.
During Scanning (while not receiving a
transmission), You Can Choose From The
Following:
a. Press and hold the TALK button to
communicate on either the channel or
channel/privacy code that was displayed
before you entered Mode Functions or the
channel on which, during scanning, you last
received a transmission. This will return the
radio to LISTENING MODE.
b. Press the MODE button to proceed to set
CTCSS privacy code on the channel that was
either displayed before you entered Mode
Functions or on which, during scanning, you
last received a transmission (see “CTCSS
Privacy Code Scan” for further details).
c. Press the LOCK button to return to
LISTENING MODE on either the channel or
channel/privacy code that was displayed
before you entered Mode Functions or the
channel on which, during scanning, you last
transmitted or received.
CTCSS Privacy Code Scan
Your microTALK® radio can automatically scan the
CTCSS privacy codes (01 to 38) within one (1)
channel.
To Scan Privacy Codes:
Select Channel
1. While in LISTENING MODE,
press the CHANNEL UP or
CHANNEL DOWN button to
choose the channel on
which you wish to scan the Mode Button
CTCSS privacy codes.
2. Press the MODE button until
the Scan icon and the small
numbers next to the
Select Scan Privacy
Codes
channel number flash on
the display.
3. Press the CHANNEL UP or
CHANNEL DOWN button to
begin scanning CTCSS
Channel Buttons
privacy codes within the
channel you selected.
MODE FUNCTIONS
OPERATION
The Scan icon will continue to be displayed when
CTCSS privacy code scan is On. Your radio will
continue to scan CTCSS privacy codes and stop as
an incoming transmission is detected. Your radio
will remain on that channel/privacy code for ten
(10) seconds.
While setting CTCSS privacy code scan, if you do
not press any buttons for fifteen (15) seconds
your radio will automatically return to LISTENING
MODE on the channel/privacy code that was
displayed before you entered Mode Functions.
During An Incoming Transmission, You
Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that channel/privacy code.
Your radio will remain on that
channel/privacy code and return to
LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume scanning CTCSS privacy
codes.
If you press the TALK button while scanning and
not within ten (10) seconds of receiving a
transmission, you will transmit on the
channel/privacy code on which you last received
a transmission. This will return the radio to
LISTENING MODE.
If you do not press any button within ten (10)
seconds, your radio will automatically resume
scanning CTCSS privacy codes.
During Scanning (while not receiving a
transmission), You Can Choose From The
Following:
a. Press and hold the TALK button to
communicate on either the channel or
channel/privacy code that was displayed
before you entered Mode Functions or
channel/privacy code on which, during
scanning, you last received a transmission.
This will return the radio to LISTENING
MODE.
b. Press the MODE button to proceed to next
available Mode Function.
c. Press the LOCK button to return to
LISTENING MODE on either the channel or
channel/privacy code that was displayed
before you entered Mode Functions or the
channel/privacy code on which, during
scanning, you last received a transmission.
English
VibrAlert and Call Alert
®
Your microTALK® radio can alert you to incoming
signals by sounding an audible call tone, by
vibrating silently, or both.
To Change Call Settings:
1. Press the MODE button until Mode Button
the Call Setting icon flashes
on the display. The current
setting (“01” – Vibrate +
Ring, “02” – Vibrate Only,
Channel Buttons
or “00” – Ring Only) is
displayed.
2. Press the CHANNEL UP or
CHANNEL DOWN button to
change the call setting.
3. When your desired call setting is displayed:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for fifteen (15)
seconds to enter the new setting and return
to LISTENING MODE.
Call Alert Icon
VibrAlert® Icon
VibrAlert® &
Call Alert Icon
Baby Monitor
With the Baby Monitor Function on, a radio left
near a baby will transmit to another unit on the
same channel and privacy code whenever a sound
is detected. Baby Monitor uses the same
sensitivity level you set for the VOX Function. If
you have not set a VOX sensitivity level (see the
“Voice Activated Transmit [VOX]” section of this
manual), the maximum sensitivity level 5 will
automatically be used.
MODE FUNCTIONS
OPERATION
To Turn Baby Monitor On:
1. Press MODE button until the Mode Button
Baby Monitor icon flashes
on the display. The current
Off setting is displayed.
2. Press the CHANNEL UP or
Select Baby Monitor
CHANNEL DOWN button to
change the setting to On.
3. Press the LOCK button to
enter the On setting and
enter BABY MONITOR
Channel Buttons
MODE.
NOTES: Pressing the MODE
button will enter the
Baby Monitor Mode
Lock Button
setting as Off and
proceed to other Mode
Functions.
Not pressing any
buttons for fifteen
(15) seconds will enter the Baby Monitor
Mode setting as Off and return the radio
to LISTENING MODE.
NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
To Terminate Baby Monitor Mode:
1. Choose one of the following:
a. Press the TALK button and return to
LISTENING MODE.
b. Press the LOCK button and return to
LISTENING MODE.
c. Press the MODE button and proceed to the
next available Mode Function.
English
2. Choose one of the following:
a. Select or edit a channel:
Channel Buttons
1) Press the CHANNEL
UP or CHANNEL
DOWN button to
select a channel
(1 to 8).
b. Select or edit a channel/privacy code:
1) Press the CHANNEL UP or CHANNEL
DOWN button to select a channel
(1 to 8).
2) Press the MODE button to set the
channel. The small numbers next to the
channel number will flash on the display.
3) Press the CHANNEL UP or CHANNEL
DOWN button to select a CTCSS privacy
code (00 to 38).
Lock Button
3. Press the LOCK button to
set Dual Watch Location 2
and engage DUAL WATCH
MODE (see below for
further details).
NOTES: To terminate Dual Watch and proceed to
the next available Mode Function, press
the MODE button.
While setting Dual Watch Location 2, if
you do not press any buttons for fifteen
(15) seconds your radio will automatically
return to LISTENING MODE on Dual Watch
Location 1.
To Turn Dual Watch On:
NOTE: Dual Watch Location 2 must be
programmed to turn Dual Watch on.
1. Set the first Dual Watch
Select Channel
Dual Watch
Location (channel/privacy
Dual Watch allows you to simultaneously monitor
code) you wish to monitor
any two (2) Dual Watch Locations:
(see “Channels” and
Dual Watch Location 1 – is always the
“CTCSS Privacy Codes”
channel/privacy code displayed before
sections for further details).
you entered Mode Functions. See
2. Press the MODE button until Mode Button
“Channels” and “CTCSS Privacy Codes”
the Dual Watch icon and the
sections for further details.
channel number flash on
Dual Watch Location 2 – will be stored in the
the display.
radio. It can be edited and/or recalled for NOTE: While setting Dual
future engagements of Dual Watch Mode.
Watch, if you do not press any buttons for
To Program Or Edit Dual Watch
fifteen (15) seconds your radio will
Location 2 And Engage Dual Watch
automatically return to LISTENING MODE on
Mode:
the last channel or channel/privacy code
1. Press the MODE button until Mode Button
displayed before you entered Mode
the Dual Watch icon and the
Functions.
channel number flash on
Lock Button
3. Press the LOCK button to
the display.
engage DUAL WATCH
MODE.
Select Dual Watch
MODE FUNCTIONS
OPERATION
English
During An Incoming Transmission, You
Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that Dual Watch Location.
Your radio will remain on that Dual Watch
Location and return to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume Dual Watch.
If you press the TALK button while in Dual Watch
and not within ten (10) seconds of receiving a
transmission, you will transmit on the last Dual
Watch Location on which you received a
transmission. This will return the radio to
LISTENING MODE.
If you do not press any button within ten (10)
seconds, your radio will automatically resume Dual
Watch.
During Dual Watch (while not receiving
a transmission), You Can Choose From
The Following:
a. Press and hold the TALK button to
communicate on either Dual Watch Location
1 or the last Dual Watch Location on which,
during Dual Watch, you last received a
transmission. This will return the radio to
LISTENING MODE.
b. Press the MODE button to proceed to other
functions.
c. Press the LOCK button to return to
5 Call Tone Settings
LISTENING MODE on either Dual Watch
Location 1 or the last Dual Watch Location
on which, during Dual Watch, you last
received a transmission.
To terminate Dual Watch:
1. Choose one of the following:
a. Press the LOCK button to return to
LISTENING MODE on either Dual Watch
Location 1 or the last Dual Watch Location
on which, during Dual Watch, you last
received a transmission.
b. Press the TALK button to return to LISTENING
MODE on either Dual Watch Location 1 or
the last Dual Watch Location on which,
during Dual Watch, you last received a
transmission.
c. Press the MODE button and proceed to the
next available Mode Function.
that you have finished talking and that it is OK for
them to speak. This feature can be turned On or
Off.
To Turn “Roger Beep” On or Off:
When you turn On your microTALK® radio for the
first time, “Roger Beep” will be On.
1. Press and release the MODE Mode Button
button until the “Roger
Beep” icon flashes on the
display. The current On or
Off setting is displayed.
Select Roger Beep
2. Press the CHANNEL UP or
CHANNEL DOWN button to
select “Roger Beep” On or
Off.
3. When your desired Roger
Channel Buttons
Beep Mode setting is
displayed, choose one of
the following:
a. Press the MODE button
to enter the new setting and proceed to
other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for fifteen (15)
seconds to enter the new setting and return
to LISTENING MODE.
The setting you select will be saved when you turn
your radio off and on again. When the “Roger
Beep” is On, the “Roger Beep” icon will be
displayed.
You can choose between five (5) different call
tone settings to transmit a unique call alert.
To Change a Call Tone Setting:
1. Press the MODE button until Mode Button
the letter “C” and the
current call tone number (1
to 5) is displayed. The
current call tone will sound
Call Tone Setting
for two (2) seconds.
2. Press the CHANNEL UP or
CHANNEL DOWN button to
hear the other call tone
settings.
Channel Buttons
3. When your desired call tone
setting is displayed, choose
one of the following:
a. Press the MODE button
to enter the new setting and proceed to
other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for fifteen (15)
seconds to enter the new setting and return
to LISTENING MODE.
"Roger Beep" Confirmation Tone
Your listener will hear an audible tone when you
release the TALK button. This alerts the other party
MODE FUNCTIONS
OPERATION
English
Keystroke Tones
With Keystroke Tones turned On, your radio will
sound beeps each time you press a button or
change a setting.
To Turn Keystroke Tones On or Off:
When you turn On your microTALK® radio for the
first time, Keystroke Tones will be On.
1. Press the MODE button until Mode Button
the Keystroke Tones icon
flashes on the display. The
current ON or OFF setting is
displayed.
Select Keystroke
2. Press the CHANNEL UP or
CHANNEL DOWN button to
turn Keystroke Tones On or
Off.
3. When your desired Keystroke Tone Mode
setting is displayed, choose one of the
following:
a. Press the MODE button to enter the new
setting and return to LISTENING MODE.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for fifteen (15)
seconds to enter the new setting and return
to LISTENING MODE.
The setting you select will be saved when you turn
your radio off and on again. When Keystroke
Tones are On, the keystroke tone icon will be
displayed.
Channel Buttons
D.O.C., OPTIONAL ACCESSORIES,
WARRANTY & CUSTOMER SERVICE
Declaration of Conformity
Optional Accessories
This declaration is the responsibility of the manufacturer/importer
Cobra Electronics Europe Limited
Dungar House
Northumberland Avenue
Dun Laoghaire
County Dublin, Ireland
Date: October 29, 2003
For accessory orders and
availability, please contact
your local dealer.
PA-BC1 . . . . . .Replacement Belt Clip
FA-BP . . . . . . .NiMH Rechargeable
Battery Pack
PA-CW . . . . . .Rapid Wall Mount Charger
(220 V, 2-pin CE plug and
240 V, 3-pin UK plug adapter)
MA-SM . . . . . .Lapel Speaker/Microphone
MA-VOX . . . . .VOX Headset
Speaker/Microphone
MA-EBM . . . . .Ear Bud Microphone
with Push To Talk Button
This certifies that the following designated product
PRIVATE MOBILE RADIO: MT 725
(Product Identification)
complies with the essential protection requirements of R & TTE
Directive 1999/5/EC on the approximation of the laws of the
Member States relating to Radio Spectrum Matters, EMC and
Electrical Safety.
This declaration applies to all specimens manufactured in accordance
with the attached technical documentation described in Annex II of
the Directive which forms part of this declaration.
Assessment of compliance of the product (class 2.6) with the
requirements relating to the essential requirements according to
Article 3 R & TTE was based on Annex IV of Directive 1999/5/EC
and the following standards:
EN 300 296-2 v.1.1.1 (02/01)
Radio Spectrum:
(Identification of regulations/standards)
EN 301 489-5 (07/2000)
EMC:
(Identification of regulations/standards)
Electrical Safety:
EN 60065: 1998
(Identification of regulations/standards)
RF Exposure:
EN 50371: 2002
(Identification of regulations/standards)
DUBLIN, IRELAND
MIKE KAVANAGH
Warranty &
Customer Service
For warranty and customer service
information, please contact your
local dealer.
PA-BC1
FA-BP
PA-CW
MA-SM
MA-VOX
1177
For use in EU countries, subject to local laws
and regulations.
CEEL™ is a trademark of Cobra Electronics
Corporation, USA.
Snake design and microTALK® are registered
trademarks of Cobra Electronics Corporation, USA.
©2003 Cobra® Electronics Europe Limited
Dungar House, Northumberland Avenue
Dun Laoghaire, County Dublin, Ireland
www.cobra.com
MA-EBM