Alliance Laundry Systems HE-HG Seies Service manual

Service
Home Laundry
Dryers
HE–HG Series and FE0080
Refer to Page 6 for Model Numbers
www.comlaundry.com
Part No. 53264R6
January 2002
Table of Contents
Section 1 – Safety Information
Locating an Authorized Servicer ............................4
Section 2 – Introduction
Customer Service ....................................................5
Nameplate Location ................................................5
Model Identification ................................................6
How Your Dryer Works ..........................................7
Section 3 – Troubleshooting
1. Motor Does Not Run ........................................9
2. Motor Overload Protector Cycles
Repeatedly ........................................................9
3. Motor Runs But Cylinder Does Not Turn ......10
4. Motor Does Not Stop .....................................10
5. Heating Element Does Not Heat and Burner
Does Not Ignite ..............................................11
6. Igniter Does Not Glow (Gas Supply Sufficient)
– Gas Models .................................................11
7. Burner Ignites and Goes Out Repeatedly
– Gas Models .................................................11
8. Igniter Glows But Burner Does Not Ignite
– Gas Models .................................................12
9. Heating Element or Burner Shuts Off
Prematurely ....................................................12
10. Heating Element Or Burner Repeatedly
Cycles Off On Limit Thermostat ...................13
11. Heating Element Or Burner Does Not
Shut Off ..........................................................13
12. Clothes Do Not Dry .......................................13
13. Timer Does Not Advance In
Automatic Cycle ............................................14
Section 4 – Grounding
14. Motor Mounting Bracket To Motor (Gas and
Electric Models) .............................................15
15. Motor Mounting Bracket to Blower Housing
Cover Plate (Gas and Electric Models) ..........15
16. Neutral at Terminal Block to Terminal Block
Bracket (Electric Models Only) .....................16
17. Terminal Block Bracket to Control Panel to
Dryer Top Panel (Electric Models Only) .......16
18. Power Cord to Terminal Block Bracket
(Gas Models Only) .........................................17
19. Terminal Block Bracket to Control Top Panel
(Gas Models Only) .........................................17
Section 5 – Service Procedures
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
Timer — All Models ......................................19
Temperature Selector Switch .........................19
Signal Control ................................................20
Light Switch ...................................................22
Start Switch — All Models ............................23
Fluorescent Tube and Tube Holders ..............23
Ballast ............................................................23
Control Panel .................................................23
Burner System Operation ...............................25
Ignition System Features ...............................26
Burner System Components – Gas Models ...27
Front Panel and Panel Seal ............................31
Burner Housing ..............................................31
Heat Shroud ...................................................32
Terminal Block or Power Cord. .....................32
Loading Door .................................................32
Inner and Outer Door Panels and
Door Handle ...................................................33
Door Striker ...................................................33
Door Seal .......................................................33
Lint Filter .......................................................33
Striker Catch ..................................................33
Door Hinge and Support Bracket ...................34
Hold-Down Clips and Guide Lugs ................34
Door Switch ...................................................35
Cylinder Light ................................................35
Cylinder Light Receptacle .............................35
High or Low Thermostats ..............................36
Limit Thermostat ...........................................37
Heating Element ............................................37
Cabinet Top ....................................................37
Control Hood .................................................38
Front Air Duct ................................................38
Exhaust Duct ..................................................39
Exhaust Fan Cover .........................................39
Motor and Exhaust Assembly ........................39
Impeller and Housing .....................................41
Motor .............................................................41
Motor Pulley and Idler Pulley Assemblies ....42
Front Bulkhead Assembly and
Cylinder Glides ..............................................42
Cylinder Belt ..................................................43
Cylinder Assembly ........................................43
(continued)
© Copyright 2002, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without
the expressed written consent of the publisher.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
61.
62.
63.
64.
65.
66.
Rear Seal ........................................................44
Cylinder Rollers and Roller Shaft ..................44
Rear Bulkhead and Heater Box ......................45
Heat Shield .....................................................46
Rear Mounting Brackets ................................46
Cabinet and Base ............................................47
Section 6 – Adjustments
67. Timer Knob Indicator ....................................49
68. Leveling Legs .................................................49
69. Burner Flame (Gas Models) ...........................50
Section 7 – Gas Burner Conversion Procedures
70. Conversion Kits – Glow Bar Ignition
System ............................................................51
71. Orifice Information ........................................51
72. Installation Instructions for 56412 and
56413 Gas Kits ...............................................52
Section 8 – Internal Wiring of Dryer Motor
Switch .....................................................................55
Model HG5009
Through Serial No. SH965837........................79
Starting Serial No. SH965838 .........................80
Models HE5003 and HE2030
Through Serial No. SH965837........................81
Starting Serial No. SH965838 .........................82
Models HG4509, HG4490, HG4390 and HG4209
Through Serial No. SH965992........................83
Starting Serial No. SH965993 .........................84
Models HG4109 and HG4009 ...............................85
Models HE4103 and HE4003 ................................86
Model HG4080 ......................................................87
Models HE4070 .....................................................88
Models HE3060 .....................................................89
Models HG3009 and HG2090 ...............................90
Models HE3003, HE2050, HE2030
and HE2003 ...........................................................91
Model HG2980 ......................................................92
Model HE2970.......................................................93
Model HG2260 ......................................................94
Model FE0080 .......................................................95
Section 9 – Wiring Diagrams ............................57
Models HG9280 and HG9260 ...............................58
Models HE9270 and HE9250 ................................59
Models HG7290 and HG7009
Through Serial No. SH965992 ........................60
Starting Serial No. SH965993 .........................61
Models HE7230 and HE7003
Through Serial No. SH965992 ........................62
Starting Serial No. SH965993 .........................63
Models HG6660, HG6380, HG4360
and HG4280 ...........................................................64
Models HE6650, HE6370, HE4503, HE4430,
HE4350, HE4330, HE4270 and HE4203
Through Serial No. SH965992 ........................65
Starting Serial No. SH965993 .........................66
Model HG6494 ......................................................67
Models HG6490 and HG2490 ...............................68
Model HE6434.......................................................69
Models HE6430, HE2430 and HE2250.................70
Model HG6360 ......................................................71
Model HE6350.......................................................72
Model HG6009
Through Serial No. SH965837 ........................73
Starting Serial No. SH965838 .........................74
Model HE6003
Through Serial No. SH965837 ........................75
Starting Serial No. SH965838 .........................76
Model HG5390 ......................................................77
Model HE5330 and HE4030..................................78
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 1
Safety Information
Throughout this manual and on machine decals, you will find precautionary statements (“CAUTION,”
“WARNING,” and “DANGER”) followed by specific instructions. These precautions are intended for the personal
safety of the operator, user, servicer, and those maintaining the machine.
a DANGER
Danger indicates the presence of a hazard that will cause severe personal injury, death, or substantial property
damage if the danger is ignored.
a WARNING
Warning indicates the presence of a hazard that can cause severe personal injury, death, or substantial property
damage if the warning is ignored.
a CAUTION
Caution indicates the presence of a hazard that will or can cause minor personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions.
IMPORTANT
The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will
occur if the procedure is not followed.
NOTE
The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is
important but not hazard related.
In the interest of safety, some general precautions relating to the operation of this machine follow.
WARNING
• Failure to install, maintain and/or operate this product according to the manufacturer’s
instructions may result in conditions which can produce serious injury, death and/or property
damage.
• Do not repair or replace any part of the product or attempt any servicing unless specifically
recommended or published in this Service Manual and that you understand and have the
skills to carry out.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the product is properly grounded and to reduce the risk of fire,
electric shock, serious injury or death.
W006R1
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Section 1 Safety Information
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
WARNING
Repairs that are made to your products by unqualified persons can result in hazards due to
improper assembly or adjustments subjecting you, or the inexperienced person making such
repairs, to the risk of serious injury, electrical shock or death.
W007
WARNING
If you or an unqualified person perform service on your product, you must assume the
responsibility for any personal injury or property damage which may result. The manufacturer
will not be responsible for any injury or property damage arising from improper service and/or
service procedures.
W008
NOTE: The WARNINGS and IMPORTANT INSTRUCTIONS appearing in this manual are not meant to
cover all possible conditions and situations that may occur. Common sense, caution and care must be
exercised when installing, maintaining or operating the dryer.
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do
not understand.
Locating an Authorized Servicer
Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper
service. Review all service information before beginning repairs.
Warranty service must be performed by an authorized technician, using authorized factory parts. If service is
required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician
and using authorized factory parts.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 2
Introduction
Customer Service
If literature or replacement parts are required, contact
the source from whom the machine was purchased or
contact Alliance Laundry Systems at (920) 748-3950
for the name and address of the nearest authorized
parts distributor.
For technical assistance, call (920) 748-3121.
Nameplate Location
When calling or writing about your product, be sure to
mention model and serial numbers. Model and serial
numbers are located on nameplate(s) as shown.
NAMEPLATE
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Section 2 Introduction
Model Identification
Information in this manual is applicable to these dryers.
Electric
Gas
HE9270
HE9250
HE7230
HE7003
HE6650
HE5330
HE5003
HE4503
HE4430
HE4350
HE4030
HE4003
HE3060
HE3003
HE2970
HG9280
HG9260
HG7290
HG7009
HG6660
HG5390
HG5009
HG4509
HG4490
HG4390
HG4009
HG3009
HG2980
HG2490
HG2260
HE6434
HE6430
HE6370
HE6350
HE6003
HE4330
HE4270
HE4203
HE4103
HE4070
HE2430
HE2250
HE2050
HE2030
HE2003
HG6494
HG6490
HG6380
HG6360
HG6009
HG4360
HG4280
HG4209
HG4109
HG4080
HG2090
FE0080
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 2 Introduction
How Your Dryer Works
CYLINDER
LINT
FILTER
EXHAUST
FAN
HEATER
DUCT
DRY14S
The dryer uses heated air to dry loads of laundry. When the motor is started, the exhaust fan pulls air in
through louvers at the rear of the dryer and over the heat source (burner flame for gas and heating element
for electric). The heated air moves through the heater duct and into the cylinder, where it circulates
through the wet load. The air then passes through the lint filter, air duct, and exhaust fan, where it is
vented to the outdoors.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Section 3
Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
IMPORTANT: Refer to appropriate model wiring diagram for aid in testing dryer components.
1. MOTOR DOES NOT RUN
POSSIBLE CAUSE
TO CORRECT
Electrical power off, fuse blown, or power cord not • Be sure to check both fuses on electric models.
plugged in.
Loading door not closed or inoperative door switch. • Close door or test switch and replace if inoperative.
Motor overload protector has cycled.
• Wait two or three minutes for overload protector to reset.
Refer to Paragraph 2 if protector cycles repeatedly.
Timer improperly set.
• Reset timer.
Inoperative motor switch.
• Test switch and replace if inoperative.
Start circuit not completed.
• Press start switch button, or test switch and replace if
inoperative.
Inoperative motor.
• Test motor and replace if inoperative.
Inoperative timer.
• Test timer and replace if inoperative.
Broken, loose, or incorrect wiring.
• Refer to appropriate wiring diagram.
2. MOTOR OVERLOAD PROTECTOR CYCLES REPEATEDLY
POSSIBLE CAUSE
TO CORRECT
Incorrect voltage.
• Refer to Installation Instructions (supplied with dryer)
for electrical requirements.
• Remove part of load. A normal washer load is a normal
dryer load.
• Check cylinder for binding and “out of round” condition.
Also check front and rear bulkheads for warping. Check
support rollers for binding. Check cylinder seals and
glides for wear or damage.
• Replace drive motor.
Clothes load too large
Clothes cylinder is binding
Inoperative motor overload protector.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
3. MOTOR RUNS BUT CYLINDER DOES NOT TURN
POSSIBLE CAUSE
TO CORRECT
Motor drive pulley loose.
Broken cylinder belt.
Clothes cylinder is binding.
• Tighten setscrew. Refer to Figure 29.
• Replace belt.
• Check cylinder for binding and “out of round” condition.
• Check front and rear bulkheads for warping.
• Check cylinder rollers for binding.
Broken or disconnected idler lever spring.
• Check cylinder seals and glides for wear or damage.
• Replace or reconnect spring. Refer to Figure 29.
4. MOTOR DOES NOT STOP
POSSIBLE CAUSE
TO CORRECT
Incorrect wiring.
Motor centrifugal switch sticky or plugged with
lint.
Inoperative door switch.
Inoperative timer.
• Refer to appropriate wiring diagram.
• Remove dust or lint and spray with “Slyde”, No. 131P4,
to clean and lubricate.
• Test switch and replace if inoperative.
• Test timer and replace if inoperative.
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
5. HEATING ELEMENT DOES NOT HEAT AND BURNER DOES NOT IGNITE
POSSIBLE CAUSE
TO CORRECT
Improper or inadequate exhaust system.
• Refer to Installation Instructions (supplied with dryer)
for exhaust requirements.
• Check fuses or circuit breakers.
• Reset switch, or test switch and replace if inoperative.
Blown fuse or tripped circuit breaker.
Temperature selector switch set at FLUFF, or
inoperative.
Timer improperly set.
Inoperative limit thermostat.
Electric Models: Inoperative heating element.
Gas Models: Insufficient gas supply.
Inoperative drive motor switch.
Gas Models: Inoperative gas valve coils.
Gas Models: Inoperative igniter.
Gas Models: Inoperative sensor.
Inoperative high or low thermostat.
Inoperative timer.
Broken, loose, or incorrect wiring.
•
•
•
•
•
•
•
•
•
•
•
Reset timer.
Test thermostat and replace if inoperative.
Replace element.
Open partially closed gas shut-off valve, or correct low
gas pressure.
Test switch and replace if inoperative.
Test coils and replace if inoperative.
Test igniter and replace if inoperative.
Test sensor and replace if inoperative.
Test thermostat and replace if inoperative.
Test timer and replace if inoperative.
Refer to appropriate wiring diagram.
6. IGNITER DOES NOT GLOW (Gas Supply Sufficient) – GAS MODELS
POSSIBLE CAUSE
TO CORRECT
No power to power leads on valve.
• Check timer, selector switch, thermostats, motor switch
and wiring.
• Replace sensor.
• Replace igniter.
Sensor failed with contacts open.
Igniter broken or open.
7. BURNER IGNITES AND GOES OUT REPEATEDLY – GAS MODELS
POSSIBLE CAUSE
TO CORRECT
Burner heat not holding sensor contacts open.
Insufficient gas supply.
Valve coils cycle rapidly.
• Replace sensor, or correct gas supply problem.
• Check gas supply and pressure.
• Replace igniter bracket.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
8. IGNITER GLOWS BUT BURNER DOES NOT IGNITE – GAS MODELS
POSSIBLE CAUSE
TO CORRECT
Sensor failed in closed position.
Open secondary coil or holding coil.
• Replace sensor.
• Replace gas valve (in-warranty), or replace coils (out-ofwarranty) with Kit No. 56225A. Refer to Paragraph 45.
• Check gas supply and pressure.
Insufficient gas supply.
9. HEATING ELEMENT OR BURNER SHUTS OFF PREMATURELY
POSSIBLE CAUSE
TO CORRECT
Improper or inadequate exhaust system.
• Refer to Installation Instructions (supplied with dryer)
for exhaust requirements.
• Open partially closed gas shut-off valve, or correct low
pressure.
• Refer to “Gas Burner Conversion Procedures” in this
manual to convert burner.
• Adjust flame. Refer to Paragraph 69.
• Momentarily connect a jumper wire across thermostat
terminals. Refer to Paragraph 10 if heating element heats
or burner ignites when jumper wire is connected.
• Replace sensor. Adjust burner flame.
Gas Models: Insufficient gas supply.
Gas Models: Dryer not properly equipped with
orifice for type of gas being used.
Gas Models: Improperly adjusted burner flame.
Cycling off on limit thermostat.
Gas models: Sensor contact closing prematurely.
Burner flame improperly adjusted.
Inoperative high or low thermostat.
Inoperative timer.
Broken, loose, or incorrect wiring.
12
• Test thermostat and replace if inoperative.
• Test timer and replace if inoperative.
• Refer to appropriate wiring diagram.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
10. HEATING ELEMENT OR BURNER REPEATEDLY CYCLES OFF ON LIMIT THERMOSTAT
POSSIBLE CAUSE
TO CORRECT
External exhaust system longer than recommended. • Refer to Installation Instructions (supplied with dryer)
for exhaust system requirements.
Clogged lint filter.
• Remove and clean lint filter.
Lint in internal dryer ductwork.
• Disassemble dryer and clean ductwork.
Lint in external exhaust system.
• Disassemble exhaust system and clean.
Hinged damper on exhaust system weather hood
• Free hinged damper or replace weather hood
not free to open.
Limit thermostat cycling at too low a temperature. • Replace thermostat, Paragraph 47.
• Replace seal or catch.
Air leak around loading door. (Door not sealing
properly against outer door seal due to damaged
seal or inoperative door catch.)
Air leak at front or rear cylinder seal.
• Check and replace seal if necessary.
11. HEATING ELEMENT OR BURNER DOES NOT SHUT OFF
POSSIBLE CAUSE
TO CORRECT
Improper motor switch.
Motor does not stop.
Incorrect wiring.
• Test switch and replace if inoperative.
• Refer to Paragraph 4.
• Refer to appropriate wiring diagram.
12. CLOTHES DO NOT DRY
POSSIBLE CAUSE
TO CORRECT
Heating element does not heat or burner does not
ignite.
Too much water in articles being dried.
Clothes load too large.
• Refer to Paragraph 5.
Improper or inadequate exhaust system.
Heating element or burner shuts off prematurely.
Gas Models: Gas line pressure too high or too low.
53264
• Remove excess water.
• Remove part of load. A normal washer load is a normal
dryer load.
• Refer to Installation Instructions (supplied with dryer)
for exhaust requirements.
• Refer to Paragraph 9.
• If natural gas line pressure to dryer exceeds 8 inch water
column pressure, or is lower than 4 inch water column, ask
gas company to correct.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Section 3 Troubleshooting
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
13. TIMER DOES NOT ADVANCE IN AUTOMATIC CYCLE
POSSIBLE CAUSE
TO CORRECT
Inoperative high or low thermostat.
Heating element does not heat or burner does not
ignite.
Heating element or burner cycles off prematurely.
Timer improperly set in FLUFF.
Broken, loose or incorrect wiring.
• Test thermostat and replace if inoperative.
• Refer to Paragraph 5.
14
• Refer to Paragraph 9.
• Reset timer.
• Refer to appropriate wiring diagram.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 4
Grounding
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
14. MOTOR MOUNTING BRACKET TO
MOTOR (Gas and Electric Models)
Figure 1
15. MOTOR MOUNTING BRACKET TO
BLOWER HOUSING COVER PLATE (Gas
and Electric Models)
Figure 2
GROUND
WIRE
DRY832S
GROUND
WIRE
Figure 1
GROUND
WIRE
DRY833S
Figure 2
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Section 4 Grounding
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
16. NEUTRAL AT TERMINAL BLOCK TO
TERMINAL BLOCK BRACKET (Electric
Models Only)
Figure 3
17. TERMINAL BLOCK BRACKET TO
CONTROL PANEL TO DRYER TOP PANEL
(Electric Models Only)
Figure 4
GROUND
WIRE
GROUND
WIRE
GROUND
WIRE
DRY834S
Figure 3
DRY835S
Figure 4
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 4 Grounding
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
18. POWER CORD TO TERMINAL BLOCK
BRACKET (Gas Models Only)
19. TERMINAL BLOCK BRACKET TO
CONTROL TOP PANEL (Gas Models Only)
GROUND
WIRE
GROUND
WIRE
GROUND
WIRE
DRY836S
Figure 5
DRY837S
Figure 6
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Section 5
Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
IMPORTANT: When reference to direction (right
or left) is made in this manual, it is from the
operator’s position facing the front of the dryer.
L2
T
H
20. TIMER — ALL MODELS
Refer to Figures 8, 9 or 10 for timer removal.
NOTE: When timer knob is installed, adjust
indicator. Refer to Paragraph 67.
N
To Test Timer Contact Points
Refer to Figure 7
1. All models: Remove panel screws and lift
assembly off panel support. Refer to Figures 8,
9 or 10.
2. Disconnect wires from timer.
NOTE: Refer to appropriate wiring diagram
when rewiring timer.
L1
P
B
3. Set meter to read Ohms and put meter probes to
terminals:
a. L1 and M to test Drive Motor circuit.
b. L2 and H to test Heat circuit
c. L2 and T to test Timer Motor circuit.
d. B and P to test Buzzer circuit.
NOTE: 52594 Timer ONLY
L1 to H to test for Heat circuit
L1 to M to test for Motor and Timer
Motor circuit.
4. Starting with timer knob indicator in OFF
position at top of timer, slowly turn timer knob
clockwise until indicator is again pointing
toward OFF position at top of timer. Meter
should register “zero” reading when circuit
being tested is completed by timer. Refer to
appropriate wiring diagram for Timer Cycle
Chart showing when circuit is made.
53264
M
DRY840S
Figure 7
21. TEMPERATURE SELECTOR SWITCH
Refer to Figures 8, 9 or 10 for switch removal.
To Test Temperature Selector Switch:
1. Remove control panel. Refer to Figures 8, 9 or
10. Lift assembly off panel support.
2. Disconnect wires from switch.
NOTE: Refer to appropriate wiring diagram
when rewiring switch.
3. Set meter to read Ohms and put meter probes on
switch terminals by following the appropriate
wiring diagram for your model dryer.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
22. SIGNAL CONTROL
Refer to Figures 8 or 9 for signal control removal.
To Test Signal Control:
1. Remove control panel, and lift assembly off
panel support. Refer to Figures 8 or 9.
2. Disconnect wires from signal control.
NOTE: Refer to appropriate wiring diagram
when rewiring signal control.
3. Set meter to read Ohms and apply probes to
terminals of signal control. Meter should read
approximately 1000 Ohms at all times.
TEMPERATURE
SELECTOR
SWITCH
START
SWITCH
SIGNAL
CONTROL
TIMER
LIGHT
SWITCH
CONTROL
PANEL
ATTACHING
SCREW
TIMER
ATTACHING
SCREW
CONTROL
PANEL
DRY841S
Figure 8
20
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
START
SWITCH
SIGNAL
CONTROL
TIMER
LOCKWASHER
CONTROL
PANEL
ATTACHING
SCREW
TEMPERATURE
SELECTOR
SWITCH
CONTROL
PANEL
CONTROL
HOOD
END
TIMER
ATTACHING
SCREW
LOCKWASHER
CONTROL
PANEL
ATTACHING
SCREW
TIMER
TEMPERATURE
SELECTOR
SWITCH
START
SWITCH
CONTROL
HOOD
END
LOCKWASHER
CONTROL
PANEL
LOCKWASHER
DRY842S
TIMER
ATTACHING
SCREW
Figure 9
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
TEMPERATURE
SELECTOR
SWITCH
(Electric Models)
START
SWITCH
LOCKWASHER
LOCKWASHER
TIMER
CONTROL
HOOD
TEMPERATURE
SELECTOR
SWITCH
(Gas Models)
END
CAP
CONTROL
PANEL
CONTROL PANEL
ATTACHING SCREW
TIMER
ATTACHING SCREW
DRY843S
Figure 10
23. LIGHT SWITCH
Refer to Figure 8 switch removal.
To Test Light Switch:
1. Remove control panel, and lift assembly off
panel support. Refer to Figure 8.
2. Disconnect all wires from light switch.
NOTE: Refer to appropriate wiring diagram
when rewiring switch.
3. Set meter to read Ohms and put probes into
terminals for two red wires. Meter should read
“infinite.”
22
4. Press light switch and meter should give “zero”
reading.
5. Insert probes of meter into terminals for black
wire and yellow/black wire.
6. Meter may read EITHER “infinite” or “zero.”
Press light switch and meter reading should
register opposite from what it was when probes
were first inserted. Meter reading should reverse
each time light switch is pressed.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
24. START SWITCH — ALL MODELS
a. Refer to Figures 8, 9 or 10 for switch removal.
1.
2.
3.
4.
5.
To Test Push-To-Start Switch
Remove control panel screws and lift assembly
off panel support. Refer to Figures 8, 9 or 10.
Set Volt-Ohm meter on Ohms scale and “zero”
at appropriate scale.
Unplug dryer from electrical supply and
disconnect wires from switch terminals.
Place meter probes on switch terminals. You
should see an “infinite” reading on the meter.
With probes attached to switch, press the Pushto-Start switch button. You should read “0”
(zero) Ohms.
25. FLUORESCENT TUBE AND TUBE
HOLDERS
Refer to Figure 11 for removal.
26. BALLAST
Refer to Figure 11 for ballast removal.
To Test Ballast:
1. Remove control panel screws and lift assembly
off panel support. Refer to Figure 11.
2. Disconnect wires from ballast.
NOTE: Refer to appropriate wiring diagram
when rewiring ballast.
3. Set meter to read Ohms and apply meter probes
to terminals of ballast. Meter should register
approximately 20 Ohms.
27. CONTROL PANEL
Type shown in Figure 8
a. Remove panel screw and lift assembly off panel
support.
b. Remove left and right control hood ends. Refer
to Figure 11.
53264
c. Lift hood top panel off panel assembly,
Figure 11.
d. Pull knob off timer shaft.
e. Pull knob off signal control and collar off light
switch ferrule nut.
NOTE: When timer knob is installed, adjust
indicator. Refer to Paragraph 67.
f. Pull knob off temperature selector switch and
remove start switch collar.
g. Tilt control panel forward slightly and raise to
disengage bottom edge of panel from panel
trim, Figure 11.
CONTROL PANEL
Type shown in Figure 9
a. Remove control panel attaching screws and lift
assembly off panel support.
b. Remove left and right control hood ends.
c. Pull knob off timer shaft.
NOTE: When timer knob is installed, adjust
indicator. Refer to Paragraph 67.
d. Pull knob off signal control, if present.
e. Pull knob off temperature selector switch, if
present and remove knurled nut and lockwasher
holding switch in control panel.
NOTE: When reinstalling switch, lockwasher must
be between knurled nut and control panel for
grounding purposes.
f. Remove hex nut holding start switch and
lockwasher in control panel.
NOTE: When reinstalling switch, lockwasher must
be between switch and control panel for grounding
purposes.
g. Remove three screws holding timer in control
panel.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
CONTROL
HOOD
END PANEL
CONTROL PANEL
CONTROL
HOOD
TOP
SUPPORT
PLATE
PANEL TRIM
DRY844S
BALLAST
Figure 11
CONTROL PANEL
Type shown in Figure 10
a. Remove control panel attaching screws and
pull panel away from control hood as far as
wires will permit.
b. Pull knob off timer shaft.
NOTE: Models equipped with the adjustable timer
knob indicator. Refer to Paragraph 67.
c. Remove three screws holding timer to control
panel.
24
NOTE: When reinstalling timer, position spacer
between timer and control panel.
d. Pull knob off temperature selector switch.
e. Remove temperature switch knurled nut, and
start switch hex nut.
f. Remove left and right end caps.
NOTE: When reinstalling switches, lockwashers
must be between switches and control panel for
grounding purposes.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
28. BURNER SYSTEM OPERATION
Refer to Figure 12
a. Components
(1) This burner has four basic components:
(a.) A silicon carbide (glow bar) igniter
(b.) Burner tube
(c.) Sensor
(d.) Two-stage gas valve consisting of a
split-coil valve and a secondary coil
valve.
(2) The split-coil valve is opened when the
dryer thermostat calls for heat, while the
secondary valve does not open until the
igniter has attained ignition temperature.
b. Pre-Ignition Circuits
(a.) When the dryer thermostat calls for
heat, circuits are completed through
the holding coil, sensor, booster coil
and igniter.
53264
(b.) Both coils must be energized to open
split-coil valve.
(c.) Once opened, the holding coil can
hold the valve open without assistance
from the booster coil.
(d.) The current shunted around the
secondary coil by the sensor, passes
through the igniter causing it to get
hot.
c. Burn Circuit
(1) In approximately 30 seconds, the igniter
attains ignition temperature and the sensor
(located on burner housing beside the
igniter) contacts open.
(2) A circuit is then completely through the
secondary valve coil, opening the valve
and allowing gas to flow.
(3) Ignition is made and the heat from the
burner flame causes the sensor contacts to
remain open.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
120 VOLT, 60 HERTZ
ELECTRICAL SUPPLY LINE
120 VOLT, 60 HERTZ
ELECTRICAL SUPPLY LINE
HOLDING
COIL
HOLDING
COIL
SECONDARY
COIL
SECONDARY
COIL
BOOSTER
COIL
SPLIT-COIL
VALVE
BOOSTER
COIL
GAS
FLOW
GAS
FLOW
SECONDARY
VALVE
SENSOR
SENSOR
IGNITER
IGNITER
PRE-IGNITION CIRCUIT
DRY839S
BURN CIRCUIT
Figure 12
29. IGNITION SYSTEM FEATURES
Refer to Figure 12
a. Momentary Power Interruption
(1) Upon resumption of power, sensor
contacts will still be open, permitting
secondary valve to open.
(2) However, with the secondary coil in the
circuit, the booster coil cannot draw
enough current to open the split-coil valve.
(3) When sensor contacts do reclose, the
secondary valve will close, and the burner
system will be in the normal pre-ignition
circuit.
26
b. Flame Failure
(1) In case of flame failure, the sensor contacts
will reclose in about 45 seconds.
(2) This will close the secondary valve and the
burner system will be in the normal preignition circuit.
c. Ignition Failure
(1) If flame is not established as sensor
contacts open, secondary valve will remain
open until sensor contacts reclose.
(2) Sensor will continue to recycle the igniter
and secondary valve (about once per
minute) until ignition is made or dryer is
turned off.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
30. BURNER SYSTEM COMPONENTS – Gas
Models
a. Complete gas valve assembly.
(1) Remove access door by applying thumb
pressure to right edge of door. When door
opens, move door to the left to disengage
from door supports. Refer to Figure 13.
(2) Close gas shutoff valve and disconnect
wires from sensor and at disconnect
blocks. Refer to Figure 14.
(3) Loosen union nut between gas shutoff
valve and nipple connector to gas valve.
Unthread nut from nipple completely.
Refer to Figure 14.
(4) Remove three hex head screws holding
valve and mounting bracket to base. Refer
to Figure 14.
SUPPORT
DRY846
ACCESS DOOR
Figure 13
DISCONNECT
BLOCKS
GAS SHUTOFF
VALVE
(Shown in the closed
position)
SENSOR
WIRES
HIGH LIMIT
THERMOSTAT
UNION
NUT
BURNER TUBE
SCREW
BURNER
HOUSING
AIR
SHUTTER
HEX HEAD
SCREW
DRY845S
Figure 14
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
(5) Lift gas valve and mounting bracket from
base and carefully remove through access
door opening.
BLUE
LOCATION A
HOLDING COIL
1100 TO 1350 OHMS
TO SENSOR
BLUE
LOCATION B
SECONDARY COIL
630 TO 770 OHMS
BLACK
BOOSTER COIL
540 TO 660 OHMS
TO SENSOR
WHITE
WHITE
TO IGNITER
RED
TO IGNITER
BLACK
To Test Gas Valve Coils:
1. Disconnect valve wire harness at molex plug,
igniter wires at disconnect block and sensor
wires from sensor control.
2. Set test meter to read OHMS and put meter
probes to terminals as follows: (Refer to
Figure 15.)
a. Location “A” (black and blue, 115 Volt
supply wires). If reading is 567 to 697
Ohms, all of the coils are okay. If reading is
1100 to 1430 Ohms, then move meter
probes to location “B”.
b. Location “B” (blue and white wires to
sensor). If reading is 1640 to 2010 Ohms,
the secondary coil is open and coil must be
replaced. If reading is 630 to 7770 Ohms,
then move meter probes to location “C”.
c. Location “C” (black and red wires to
igniter). If reading is 540 to 660 ohms,
holding coil is open and coil must be
replaced. If reading 1730 to 2120 Ohms,
booster coil is open and must be replaced.
115 VOLT SUPPLY
BLACK
NOTE: The holding coil, booster coil and secondary
coil can be replaced individually or in a kit. Refer to
the parts section of this manual for the correct part
numbers.
LOCATION C
NOTE: Test procedure can be performed on
workbench if gas valve, igniter, burner tube and
burner housing are removed from dryer.
DRY871S
Figure 15
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
b. Burner tube and igniter
NOTE: Burner tube and igniter can be removed
without removing gas valve and bracket.
(1) Remove one screw from right side of
burner housing holding burner tube in
place. Refer to Figure 14.
(2) Gently move burner tube toward rear of
dryer to disengage tab from slot on left side
of burner housing. Refer to Figure 16.
HEAT
SHROUD
HEX HEAD
SCREW
HIGH LIMIT
THERMOSTAT
BURNER
TUBE
SCREW
WARNING
Handle igniter by grasping white ceramic
portions only. DO NOT handle silicon
carbide portion of igniter with hands or
allow any oil, grease or other foreign
material to contaminate it. Oil, grease and
other impurities or hairline cracks will cause
igniter to burn out.
c. Igniter. Refer to Figure 17
(1) Remove burner tube and igniter, paragraph
30, section b, steps 1 through 4.
(2) Carefully remove igniter by spreading
mounting clips with a Tru-Arc pliers.
BURNER
TUBE
BURNER
HOUSING
SENSOR
VALVE
UNION
NUT
D397S
MOUNTING
CLIP
Figure 16
(3) Carefully rotate burner tube and igniter
counterclockwise so tab is at 8 o’clock
position.
(4) Move air shutter end of burner tube slightly
to right and CAREFULLY remove burner
tube and igniter assembly out through front
of dryer.
CAUTION
Use care in removal so as not to damage or
break igniter as it is very fragile.
53264
DRY847S
55438
IGNITER
Figure 17
CAUTION
Use care in removal so as not to damage or
break igniter as it is very fragile.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
WARNING
Handle igniter by grasping white ceramic
portions only. DO NOT handle silicon
carbide portion of igniter with hands or
allow any oil, grease or other foreign
material to contaminate it. Oil, grease and
other impurities or hairline cracks will cause
igniter to burn out.
To Test Igniter:
1. Remove access door by applying thumb
pressure to right edge of door. When door opens,
move door to the left to disengage from door
supports. Refer to Figure 13.
2. Disconnect igniter wires at molex plug.
3. Set test meter to read Ohms and put meter
probes on terminals of igniter wires.
4. Meter should register an Ohm reading of at least
40 Ohms at the minimum. If meter does not
register any Ohms or less than 40 Ohms, replace
the igniter.
IMPORTANT: Always examine all wires,
terminals and connectors to be sure wiring is
proper before replacing any components.
NOTE: Test procedure can be performed on
workbench if gas valve, igniter, burner tube and
burner housing are removed from dryer.
30
d. Sensor. Refer to Figure 16
(1) Remove access door by applying thumb
pressure to right edge of door. When door
opens, move door to the left to disengage
from door supports. Refer to Figure 13.
(2) Remove wires from sensor terminals.
(3) Remove screw holding sensor to burner
housing.
e. High Limit Thermostat. Refer to Figure 16.
(1) Remove access door by applying thumb
pressure to right edge of door. When door
opens, move door to the left to disengage
from door supports. Refer to Figure 13.
(2) Remove wires from thermostat.
(3) Remove two hex head screws holding
thermostat to burner housing and remove
thermostat.
To Test Sensor:
1. Remove access door by applying thumb
pressure to right edge of door. When door opens,
move door to the left to disengage from door
supports. Refer to Figure 13.
2. Remove wires from sensor terminals. Refer to
Figure 16.
3. Set test meter to read Ohms and put meter
probes on sensor terminals. Meter should read
“zero” Ohms. If meter registers an Ohm reading
of any amount, replace sensor.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
To Test Electrical Circuit to Ignition System:
1. Remove access door and close gas shut-off
valve.
2. Disconnect valve wire harness from dryer
harness at molex plug.
3. Plug dryer power cord into wall receptacle, set
FABRIC switch and timer into positions calling
for heat and start dryer.
4. Set test meter to read AC voltage and apply
meter probes into PINK and WHITE wire
terminals on dryer harness side of molex plug.
Meter should register line voltage in all
FABRIC settings, except FLUFF which should
read “zero” VAC.
5. If meter does not register as explained in step
“4”, check motor switch and timer motor circuit.
31. FRONT PANEL AND PANEL SEAL
Refer to Figure 21
a. Remove two screws from bottom edge of front
panel.
b. Swing bottom of panel away from dryer to
disengage hold-down clips and guide lugs from
cabinet top.
c. Disconnect wires from door switch (refer to
appropriate wiring diagram when rewiring
switch).
d. Remove front panel seal from flange around
inside of door opening.
NOTE: Be sure seal is positioned properly when
replacing.
53264
32. BURNER HOUSING
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Close gas shutoff valve and disconnect wires
from sensor and disconnect blocks. Refer to
Figure 14.
c. Loosen union nut between gas shutoff valve
and nipple connector to gas valve. Unthread nut
from nipple complete. Refer to Figure 14.
d. Remove screws holding valve and bracket to
base. Refer to Figure 14.
e. Lift gas valve and mounting bracket from base
and carefully remove out through front of dryer.
f. Remove screw from right side of burner
housing holding burner tube in place. Refer to
Figure 14.
g. Gently move burner tube toward rear of dryer to
disengage tab from slot on left side of burner
housing. Refer to Figure 16.
h. Carefully rotate burner tube and igniter
counterclockwise to tab is at 8 o’clock position.
i. Move air shutter end of burner tube slightly to
right and CAREFULLY remove burner tube
and igniter assembly out through front of dryer.
CAUTION
Use care in removal so as not to damage or
break igniter as it is very fragile.
j. Remove hex head screw holding burner
housing to heat shroud. Refer to Figure 16.
k. Remove hex head screw holding front of burner
housing to dryer base and remove housing out
through front of dryer.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
33. HEAT SHROUD
a. Remove front panel. Refer to Paragraph 31,
steps “a’ through “c”.
b. Remove burner housing. Refer to Paragraph
32, steps “b” through “k”.
c. Remove four hex head screws holding shroud
to heater box and remove shroud out through
front of dryer. Refer to Figure 16.
34. TERMINAL BLOCK OR POWER CORD.
Terminal Block - Electric Models
Refer to Figure 18
a. Remove access plate on rear of cabinet.
b. Remove all wires from terminal block. (Refer
to appropriate wiring diagram when rewiring
terminal block.)
c. Remove screws holding terminals block to
bracket.
NOTE: Do not let terminal block insulation drop
when removing the block. Insulation must be in
place when reinstalling block.
Power Cord - Gas Models
d. Remove access plate on rear of cabinet.
e. Remove strain relief.
f. Remove screw holding power cord ground wire
to terminal block bracket.
NOTE: Reconnect ground wire into same hole in
bracket when reinstalling power cord.
g. Disconnect molex plug and remove strain relief
and power cord from rear of dryer cabinet.
35. LOADING DOOR
a. Remove four Phillips head screws holding
hinges to door. Refer to Figure 19.
HINGE
SCREWS
TERMINAL BLOCK
SCREW
DRY849
LINT
FILTER
Figure 19
GROUND
WIRE
ACCESS
PLATE
DRY848S
Figure 18
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
36. INNER AND OUTER DOOR PANELS AND
DOOR HANDLE
Refer to Figure 20
a. Remove loading door. Refer to Paragraph 27.
b. Remove two hex head screws holding handle to
door.
a. Open loading door and remove seal from inner
door panel.
NOTE: When replacing seal, be sure seal is not
stretched or distorted. Use a heat resistant adhesive
(such as Krazy Glue®) to adhere door seal to inner
door panel.
37. DOOR STRIKER
Refer to Figure 20
a. Remove two hex head screws holding handle to
door.
b. Spread door panels just far enough to depress
tabs on top and bottom of striker and push out
of inner panel.
38. DOOR SEAL
Refer to Figure 20
39. LINT FILTER
Refer to Figure 19
a. Open loading door and lift filter out of air duct.
40. STRIKER CATCH
a. Remove front panel. Refer to Paragraph 31,
steps “a” and “c”.
b. Depress tabs on top and bottom of catch and
push out of front panel. Refer to Figure 21.
DOOR
STRIKER
DOOR
SEAL
OUTER
DOOR PANEL
INNER
DOOR
PANEL
DOOR
HANDLE
HINGE
DRY850S
Figure 20
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
HOLD-DOWN
CLIP
DOOR
SWITCH
GUIDE
LUG
FRONT
PANEL SEAL
STRIKER
CATCH
ACCESS
DOOR
SUPPORT BRACKET
(Through Serial No.
S70U4371)
DOOR
HINGE
PHILLIPS
HEAD SCREWS
LOCKNUT
DRY851S
HEX
HEAD SCREW
Figure 21
41. DOOR HINGE AND SUPPORT BRACKET
a. Open loading door and remove four screws
holding door assembly to hinges. Refer to
Figure 19.
b. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
c. Remove four Phillips head screws and locknuts
holding hinges to front panel. Refer to
Figure 21.
42. HOLD-DOWN CLIPS AND GUIDE LUGS
Refer to Figure 21
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Compress hold-down clips and remove from
slot in top flange of front panel.
c. Remove four screws holding four guide lugs to
front panel.
NOTE: Through Serial No. S70U4371, support
bracket is removed with lower hinge. Support
bracket must be installed when reassembling.
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
43. DOOR SWITCH
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Depress tabs on top and bottom of switch and
push out of front panel. Refer to Figure 22.
(Refer to appropriate wiring diagram when
rewiring switch.)
DOOR
SWITCH
TABS
44. CYLINDER LIGHT
a. Open loading door and remove bulb through
top opening in the front bulkhead by pushing up
and turning bulb to the left. Refer to Figure 23.
45. CYLINDER LIGHT RECEPTACLE
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Disconnect wires at connectors.
c. Remove two Phillips head screws and
lockwashers holding receptacle to front
bulkhead. Refer to Figure 23.
CYLINDER
LIGHT
D240S
Figure 22
PHILLIPS
HEAD
SCREWS
To Test Door Switch:
1. Disconnect wires from door switch.
NOTE: Refer to appropriate wiring diagram
when rewiring switch.
2. Set meter to read Ohms and apply meter probes
on switch terminals 1 and 3 with door closed.
You should get “zero” reading.
3. Apply probes to terminals 1 and 2 with door
closed. The meter should read “infinite.”
4. Open door. Meter should read “infinite”
between 1 and 3 and “zero” between 1 and 2.
53264
DRY852S
Figure 23
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
46. HIGH OR LOW THERMOSTATS
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Refer to Figure 24 for thermostat removal.
HIGH
THERMOSTAT
LOW
THERMOSTAT
DRY853S
Figure 24
LIMIT
THERMOSTAT
ELEMENT
GAS VALVE SHOWN
IN CLOSED POSITION
LIMIT
THERMOSTAT
ELEMENT
ATTACHING
SCREWS
DRY855S
BURNER
HOUSING
DRY854S
ELECTRIC MODELS
GAS MODELS
Figure 25
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
47. LIMIT THERMOSTAT
ELECTRIC MODELS
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Refer to Figure 25 for thermostat removal.
CABINET TOP
HOLD-DOWN
SCREW
GAS MODELS
a. Remove access door by applying thumb
pressure to right edge of door. When door
opens, move door to the left to disengage from
door support.
b. Refer to Figure 25 for thermostat removal.
48. HEATING ELEMENT
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove two hex head screws holding element
and plate to heater box and pull element down
and away from heater box. Refer to Figure 25.
c. Disconnect wires from element terminals and
remove high limit thermostat.
NOTE: When reassembling, be sure all wire
connections are tight on element terminals and high
limit thermostat.
49. CABINET TOP
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove control panel. Refer to Paragraph 27
and Figures 8, 9 or 10.
c. Disconnect wire harness from all components
and ground wire in control hood. Push harness
through opening in cabinet top. (Replace
control panel or set aside to prevent damage.)
DRY856S
Figure 26
f. Remove brace from underside of top by
swinging one end to front or rear.
g. Remove control hood and panel support if
necessary when replacing cabinet top.
NOTE: Cabinet top may be raised and hinged on
the rear hold-down brackets, or supported against
wall behind dryer when servicing.
NOTE: Refer to appropriate wiring diagram when
reconnecting wires.
d. Remove two cabinet hold-down screws. Refer
to Figure 26.
e. Lift front of cabinet top and disengage from
hinges on rear of cabinet. Refer to Figure 27.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
50. CONTROL HOOD
a. Remove control panel and support bracket.
Refer to Paragraph 27 and Figures 8, 9 or 10.
Disconnect all wires. (Refer to appropriate
wiring diagram when reconnected.)
b. Remove or raise cabinet top. Refer to
Paragraph 49.
c. Support hood and remove 6 screws holding
control hood to cabinet top. Refer to Figure 27.
HEX
HEAD
SCREWS
BRACE
AIR
DUCT
HEX
HEAD
SCREWS
DRY858S
CABINET TOP
HINGES
Figure 28
COVER
ATTACHING
SCREWS
CONTROL HOOD
ATTACHING SCREWS
EXHAUST
FAN
COVER
DRY857S
Figure 27
51. FRONT AIR DUCT
a. Remove front panel. Refer to Paragraph 31,
steps “a’ through “c”.
b. Remove lint filter. Refer to Figure 19.
c. Remove hex head screws holding duct to front
bulkhead and lift off. Refer to Figure 28.
NOTE: When reassembling, be sure felt seal on
exhaust fan cover makes air tight seal on flange of
duct. Refer to Figure 29.
DRY853S
MOTOR MOUNT
ATTACHING SCREWS
Figure 29
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
52. EXHAUST DUCT
a. Disconnect electric power, vent (and gas line if
necessary) and move unit to gain access to rear
of dryer.
b. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
c. Remove one hex head screw holding bracket on
exhaust duct to rear of cabinet.
d. Pull duct out through rear of cabinet.
53. EXHAUST FAN COVER
a. Remove front panel. Refer to Paragraph 31,
steps “a’ through “c”.
b. Remove lint filter. Refer to Figure 19.
c. Remove hex head screws holding air duct to
front bulkhead and lift off. Refer to Figure 28.
NOTE: When reassembling, be sure felt seal on
exhaust fan cover makes air tight seal on flange of
air duct. Refer to Figure 29.
d. Disconnect wires from thermostats.
54. MOTOR AND EXHAUST ASSEMBLY
a. Remove front panel. Refer to Paragraph 31,
steps “a’ through “c”.
b. Remove lint filter. Refer to Figure 19.
c. Remove hex head screws holding air duct to
front bulkhead and lift off. Refer to Figure 28.
NOTE: When reassembling, be sure felt seal on
exhaust fan cover makes air tight seal on flange of
air duct. Refer to Figure 29.
d. Disconnect wires from thermostats.
NOTE: Refer to appropriate wiring diagram when
rewiring thermostats.
e. Remove cylinder belt from idler and motor
pulleys.
f. Remove two screws holding motor mounting
bracket to dryer base. Refer to Figure 29. Then
pull complete assembly out through front of
dryer.
g. Disconnect wires from motor switch.
NOTE: Refer to appropriate wiring diagram when
rewiring thermostats.
NOTE: Refer to appropriate wiring diagram when
rewiring motor switch.
e. Remove hex head screw holding ground wire to
exhaust fan cover. Refer to Figure 29.
IMPORTANT: When reinstalling motor and
exhaust assembly, be sure wire harness on right side
is clipped to motor mounting bracket and is routed
along dryer base (between motor mounting bracket
and right side of cabinet). Refer to Figure 29. Tab on
rear of motor mounting bracket must be slid into
slot in dryer base. Exhaust duct MUST BE
reinstalled on rear flange of exhaust housing.
NOTE: Ground wire must be rerouted as shown in
Figure 29. (Refer to Section 2, Grounding.)
f. Remove hex head screws holding cover to
housing. Refer to Figure 29.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
To Test Drive Motor:
(Refer to Figure 30)
1. Disconnect wires from motor switch.
4. Put test meter probes on terminal 5 and motor
frame. Meter should register “no reading” or
NOTE: Refer to appropriate wiring diagram when
infinite.
rewiring motor switch.
5. Put test meter probes on terminals 4 and 6. Meter
should register “no reading” or infinite. Manually
2. Put test meter probes on terminals 4 and 5. Meter
flex
the centrifugal switch in motor and meter
should read approximately one on Ohm scale.
should read approximately two on Ohm scale.
3. Put test meter probes on terminal 4 and motor
6. Put test meter probes on terminals 1 and 2. Meter
frame. Meter should register “no reading” or
should register “no reading.” Manually flex the
infinite.
centrifugal switch in motor and meter should
read “zero” Ohms.
MOTOR
SWITCH
DRIVE
MOTOR
GROUND
WIRES
DRY838S
Figure 30
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
55. IMPELLER AND HOUSING
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove motor and exhaust assembly. Refer to
Paragraph 54, steps “b” through “g”.
c. Hold motor pulley securely and unthread
impeller from motor shaft. (Right hand thread.)
d. Remove three hex head screws and washers
which hold the exhaust housing to the motor
mounting bracket. Refer to Figure 31.
EXHAUST
HOUSING
ATTACHING
SCREWS
56. MOTOR
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove motor and exhaust assembly. Refer to
Paragraph 54, steps “b” through “g”.
c. Remove hex head screw holding ground wire to
exhaust fan cover. Refer to Figure 29.
NOTE: Ground wire must be routed as shown in
Figure 29. Refer to Section 2, Grounding.
d. Hold motor pulley securely and unthread
impeller from motor shaft. (Right hand thread.)
e. Remove the three screws and washers which
hold the exhaust housing to the motor mounting
bracket. Refer to Figure 31.
f. Disconnect ground wire from motor.
g. Remove two motor strap assemblies holding
motor in mounting bracket. Refer to Figure 32.
Then lift motor out of mounting bracket.
NOTE: When replacing motor, motor switch
location should be a 10 o’clock. Refer to Figure 32.
NOTE: Refer to appropriate wiring diagram when
rewiring motor switch.
D402S
Figure 31
TO REMOVE MOTOR SWITCH
a. Remove two screws holding switch to motor.
b. Disconnect internal motor leads from switch
terminals.
NOTE: Refer to wiring schematic when rewiring
internal motor switch leads.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
MOTOR STRAP
GROUND
WIRE
CABINET
ATTACHING
SCREWS
IDLER
PULLEY
SLOT
HEX
HEAD
SCREWS
IDLER
LEVER
IDLER
SPRING
MOTOR
PULLEY
DRY860S
Figure 32
57. MOTOR PULLEY AND IDLER PULLEY
ASSEMBLIES
a. Remove front panel. Refer to Paragraph 31,
steps “a’ through “c”.
b. Remove motor and exhaust assembly. Refer to
Paragraph 54, steps “b” through “g”.
c. Refer to Figure 32 for motor and idler pulley
removal.
58. FRONT BULKHEAD ASSEMBLY AND
CYLINDER GLIDES
a. Remove front panel. Refer to Paragraph 31,
steps “a’ through “c”.
b. If present, disconnect cylinder light wires at
connectors.
c. Remove four hex head screws holding
bulkhead to front flange of cabinet and lift
complete bulkhead assembly out of slots in
cabinet. Refer to Figure 33.
d. Remove cylinder glides. Refer to Figure 34.
NOTE: Front air duct will be removed with the
bulkhead unless it had been previously removed in
Paragraph 51.
42
DRY858S
Figure 33
e. If present, remove two Phillips head screws and
lockwashers holding light receptacle to front
bulkhead. Refer to Figure 23.
TO REMOVE FRONT CYLINDER SEAL
a. Unhook spring from seal strap. Refer to
Figure 34.
IMPORTANT: When installing seal, tape it to the
bulkhead in several places to hold in position while
replacing seal strap and spring. Remove tape after
strap and spring are in place. Seal must be under
strap securely and be folded under flanged edge
around entire bulkhead. Strap must be installed
with cupped surface down against the seal to hold
the felt seal more firmly in place on the bulkhead.
Also, the seal can be adhered to the bulkhead using
3M-1300 Sealant (obtain locally). This is
accomplished by applying a bead of 3M-1300
Sealant around the entire flanged area where the
felt seal contacts the bulkhead.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
Seal must be
positioned under
flanged edge
FELT
SEAL
TAPE
SEAL STRAP
(Installed with
cupped surface
against seal)
SPRING
60. CYLINDER ASSEMBLY
a. Remove front panel. Refer to Paragraph 31,
steps “a’ through “c”.
b. If present, disconnect cylinder light wires at
connectors.
c. Remove four hex head screws holding
bulkhead to front flange of cabinet. Then lift
complete bulkhead assembly out of slots in
cabinet. Refer to Figure 33.
d. Disengage belt from motor and idler pulleys.
Refer to Figure 35.
e. Remove two cabinet top hold-down screws.
Refer to Figure 26.
f. Carefully remove cylinder out through front of
dryer.
NOTE: When reinstalled cylinder, be sure belt is
properly positioned around cylinder and on motor
and idler pulleys. Refer to Figure 35.
CYLINDER GLIDE
ATTACHING SCREW
BELT
IDLER
PULLEY
DRY861S
Figure 34
59. CYLINDER BELT
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. If present, disconnect cylinder light wires at
connectors.
c. Remove four hex head screws holding
bulkhead to front flange of cabinet. Then lift
complete bulkhead assembly out of slots in
cabinet. Refer to Figure 33.
d. Disengage belt from motor and idler pulleys.
Refer to Figure 35.
e. While supporting cylinder, carefully remove
belt off cylinder.
MOTOR
PULLEY
DRY862S
Figure 35
NOTE: When installing belt, be sure belt is
properly positioned around cylinder and on motor
and idler pulleys. Refer to Figure 35.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
TO REMOVE BAFFLES
a. Remove screws and washers (if present)
holding baffles to cylinder. Refer to Figure 36.
BAFFLE
CYLINDER
strap and spring are in place. Seal must be under
strap securely and be folded under flanged edge
around entire bulkhead. Strap must be installed
with cupped surface down against the seal to hold
the felt seal more firmly in place on the bulkhead.
Also, the seal can be adhered to the bulkhead using
3M-1300 Sealant (obtain locally). This is
accomplished by applying a bead of 3M-1300
Sealant around the entire flanged area where the
felt seal contacts the bulkhead.
62. CYLINDER ROLLERS AND ROLLER
SHAFT
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove cylinder assembly. Refer to Paragraph
60, steps “b” through “e”.
c. Refer to Figure 38 for removal of roller from
roller shaft.
HEX HEAD
SCREW
WASHER
(if present)
DRY863S
Figure 36
61. REAR SEAL
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove two cabinet top hold-down screws.
Refer to Figure 26.
c. Lift front of cabinet top and disengage from
hinges on rear of cabinet. Refer to Figure 27.
¢¢¢¢¢¢¢¢¢
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
€€
ÀÀ
;;
QQ
¢¢
@@
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
QQ
¢¢
@@
€€
ÀÀ
;;
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
ÀÀ
;;
QQ
¢¢
@@
€€
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
¢¢
@@
€€
ÀÀ
;;
QQ
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
@@@@@@@@@
€€€€€€€€€
ÀÀÀÀÀÀÀÀÀ
;;;;;;;;;
QQQQQQQQQ
¢¢¢¢¢¢¢¢¢
PHILLIPS HEAD
SCREWS
SEAL
STRAP
SPRING
CYLINDER
ROLLERS
NOTE: Cabinet top may be raised and hinged on
the rear hold-down brackets, or supported against
wall behind the dryer.
IMPORTANT: When installing seal, tape it to the
bulkhead in several places to hold in position while
replacing seal strap and spring. Remove tape after
44
HEX HEAD
SCREW
HEAT
SHIELD
DRY864S
Figure 37
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
NOTE: When reassembling, be sure all wire
connections are tight on element terminals and to
high limit thermostat.
g. Remove two hex head screws holding heater
box to heat shield. Refer to Figure 37.
h. Remove one Phillips head screws holding rear
bulkhead to terminal block bracket. While
supporting bulkhead, remove the four Phillips
head screws holding rear bulkhead to mounting
brackets. Refer to Figure 37. Lift complete
assembly out of dryer.
TO REMOVE HEATER BOX FROM REAR
BULKHEAD
a. Refer to Figure 39 for removal.
SPACER
WASHER
WASHER
SHAFT
RETAINER
RING
DRY865S
ROLLER
REAR
BULKHEAD
HEATER BOX
ATTACHING
SCREWS
Figure 38
63. REAR BULKHEAD AND HEATER BOX
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove cylinder assembly. Refer to Paragraph
60, steps “b” through “e”.
c. Gas Models –Remove burner housing. Refer to
Paragraph 32, steps “b” through “j”.
d. Gas Models–Remove four hex head screws
holding heat shroud to heater box. Refer to
Figure 16. Remove shroud out through front of
dryer.
e. Electric Models–Remove two hex head screws
holding element and plate to heater box. Pull
element down and away from heater box. Refer
to Figure 25.
f. Electric Models – Disconnect wires from
element terminals and from high limit
thermostat.
53264
DRY866S
Figure 39
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
45
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
64. HEAT SHIELD
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove cylinder assembly. Refer to Paragraph
60, steps “b” through “e”.
c. Gas Models – Remove burner housing. Refer to
Paragraph 32, steps “b” through “j”.
d. Gas Models – Remove four hex head screws
holding heat shroud to heater box. Refer to
Figure 16. Remove shroud out through front of
dryer.
e. Electric Models – Remove two hex head screws
holding element and plate to heater box. Pull
element down and away from heater box. Refer
to Figure 25.
f. Electric Models – Disconnect wires from
element terminals and from high limit
thermostat.
REAR MOUNTING
BRACKET ATTACHING
SCREWS
GROUND
SCREW
HEAT SHIELD
ATTACHING
SCREWS
(if present)
NOTE: When reassembling, be sure all wire
connections are tight on element terminals and to
high limit thermostat.
DRY867S
Figure 40
g. Remove two hex head screws holding heater
box to heat shield. Refer to Figure 37.
h. Disconnect vent and move dryer to gain access
to rear of dryer.
i. Remove two hex head screws holding heat
shield to rear of dryer cabinet. Refer to
Figure 40.
65. REAR MOUNTING BRACKETS
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove cylinder assembly. Refer to Paragraph
60, steps “b” through “e”.
c. Gas Models – Remove burner housing. Refer to
Paragraph 32, steps “b” through “j”.
d. Gas Models – Remove four hex head screws
holding heat shroud to heater box. Refer to
Figure 16. Remove shroud out through front of
dryer.
e. Electric Models – Remove two hex head screws
holding element and plate to heater box. Pull
46
element down and away from heater box. Refer
to Figure 25.
f. Electric Models – Disconnect wires from
element terminals and from high limit
thermostat.
NOTE: When reassembling, be sure all wire
connections are tight on element terminals and to
high limit thermostat.
g. Remove two hex head screws holding heater
box to heat shield. Refer to Figure 37.
h. Remove one Phillips head screw holding rear
bulkhead to terminal block bracket. While
supporting bulkhead, remove the four Phillips
head screws holding rear bulkhead to mounting
brackets. Refer to Figure 37. Lift complete
assembly out of dryer.
i. Remove five screws holding rear mounting
brackets to rear of dryer cabinet. Refer to
Figure 40.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 5 Service Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
66. CABINET AND BASE
a. Remove front panel. Refer to Paragraph 31,
steps “a” through “c”.
b. Remove control panel screws and lift assembly
off panel support.
c. Disconnect wire harness from all components,
and ground wire in control hood. Push harness
through hole in cabinet top. Set control panel
aside to prevent damage.
d. Remove two cabinet top hold-down screws.
Refer to Figure 26.
e. Lift front of cabinet top and disengage from
hinges on rear of cabinet. Refer to Figure 27.
Set cabinet top aside to prevent damage.
f. Remove cylinder assembly. Refer to Paragraph
60, steps “b” through “e”.
g. Disconnect wires from thermostats located on
exhaust fan cover.
n. Remove two hex head screws holding heater
box to heat shield. Refer to Figure 37.
o. Remove one Phillips head screw holding
bulkhead to terminal block bracket. While
supporting bulkhead, remove the four Phillips
head screws holding rear bulkhead to mounting
brackets. Refer to Figure 37. Lift complete
assembly out of dryer.
p. Disconnect vent and move dryer to gain access
to rear of dryer.
q. Remove two hex head screws holding heat
shield to rear of dryer cabinet. Refer to
Figure 40.
r. Remove two hex head screws from front edge
at each side of cabinet. Refer to Figure 33.
Remove remaining screws from around bottom
of cabinet and lift cabinet off base.
NOTE: Refer to appropriate wiring diagram when
rewiring thermostats.
h. Remove two screws holding motor mounting
bracket to dryer base. Refer to Figure 29. Pull
complete assembly out through front of dryer.
i. Disconnect wires from motor switch.
NOTE: Refer to appropriate wiring diagram when
rewiring thermostats.
j. Gas Models – Remove burner housing. Refer to
Paragraph 32, steps “b” through “j”.
k. Gas Models – Remove four hex head screws
holding heat shroud to heater box and remove
shroud. Refer to Figure 16.
l. Electric Models – Remove two hex head screws
holding element and plate to heater box and
remove. Refer to Figure 25.
m. Electric Models – Disconnect wires from
element terminals and from high limit
thermostat.
NOTE: When reassembling, be sure all wire
connections are tight on element terminals and to
high limit thermostat.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Section 6
Adjustments
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
67. TIMER KNOB INDICATOR
a. With timer knob indicator in top OFF position,
push in and hold start switch button. Slowly
turn timer knob clockwise only until dryer
starts. Then immediately open the loading door
to stop dryer.
b. If dryer starts with indicator still in the OFF
position, proceed as follows:
(1) Hold knob firmly and move indicator and
plate one “click” in a clockwise direction.
(2) Check position in reference to the right
hand vertical line of the OFF position.
(3) If the indicator is still in the OFF portion of
dial, move it one more “click” in a
clockwise direction.
(4) Repeat this adjustment until the indicator is
on the right hand vertical line of the OFF
position.
c. If dryer starts with indicator past the right hand
vertical line of the OFF position, follow
instructions in “Step b” above EXCEPT move
indicator and plate in a counterclockwise
direction one “click” at a time until indicator
and right hand vertical line of OFF position
match up.
53264
DRYER
BASE
LEVELING
LEG
LOCKNUT
DRY868S
Figure 41
68. LEVELING LEGS
a. Threads locknuts down to heads of leveling
legs, then thread legs into dryer base until head
extend out of base approximately 3/4 inch.
Refer to Figure 41.
b. Turn legs in or out of base as necessary to level
dryer. All four legs must rest firmly on the
floor.
c. Tighten locknuts securely against dryer base.
Refer to Figure 41.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49
Section 6 Adjustments
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
69. BURNER FLAME (Gas Models)
a. Close loading door, set fabric selector switch at
NORMAL, set timer at “65”, and push start
switch button to start dryer.
b. Allow dryer to operate for approximately five
minutes, then open access door and loosen air
shutter lockscrew. Refer to Figure 42.
c. Turn air shutter to the right or left to obtain a
soft, uniform blue flame. (A lazy, orangetipped flame indicates lack of air. A harsh,
roaring, very blue flame indicates too much
air.)
d. After proper flame is obtained, tighten air
shutter lockscrew securely. Refer to Figure 42.
AIR
SHUTTER
SHUT-OFF VALVE
HANDLE
APPLY
VALVE CONVERTED
OR VALVE NUMBER
STICKER HERE
BURNER
TUBE
SCREW
AIR SHUTTER
LOCKSCREW
1/8” (3.1 mm)
PIPE PLUG
(For checking
manifold
pressure)
DRY855S
Figure 42
50
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 7
Gas Burner Conversion Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
WARNING
This conversion kit is to be installed by AUTHORIZED DEALERS or DISTRIBUTORS on their
premises and in accordance with the manufacturer’s instructions and all codes and
requirements of the authority having jurisdiction. Failure to follow instructions could result in
serious injury or property damage. The qualified agency performing this work assumes
responsibility for this conversion.
W312
70. CONVERSION KITS – Glow Bar Ignition
System
All gas dryers manufactured with glow bar
ignition are factory equipped for Natural/Mixed
gas operation.
No. 56412 Natural/Mixed to L.P. Gas Kit is
available from your parts supplier. This kit
consists of:
1 - 51211
Burner Orifice Spud
1 - 53390
Block-Open Plug and Gasket
1 - 53408
Change-Over Sticker
1 - 55753
“Valve Converted” Sticker
2 - 56426
L.P. Gas Stickers
IMPORTANT: The Conversion Kit is intended for
installation only in unused dryers. Installation
should be made by authorized Dealers or
Distributors on their premises.
NOTE: When converting the dryer gas valve to L.P.
gas, be sure the incoming gas supply line is equipped
with a pressure regulator (located ahead of the
dryer) that will maintain the gas supply to the dryer
at 11 ± 2 inches (2.74 ± .4 kPa) water column
pressure.
53264
No. 56413 L.P. to Natural/Mixed Gas Kit is
available for field conversion. This kit consists of:
1 - 50326
Burner Orifice Spud
1 - 53556
Change-Over Sticker
1 - 53952
Vent Screw and Gasket
1 - 56414
Valve Number Sticker
2 - 56427
Natural Gas Stickers
IMPORTANT: Installation of this Conversion Kit
must be made by a qualified serviceman, or an
Authorized Dealer or Distributor.
NOTE: When converting the dryer gas valve to
Natural Gas, be sure the incoming gas supply line is
equipped with a pressure regulator (located ahead
of the dryer) that will maintain the gas supply to the
dryer at 7 ± 2 inches (1.74 ± .5 kPa) water column
pressure.
71. ORIFICE INFORMATION
Burner
Orifice
Kind
of Gas
Natural/Mixed
Liquefied
Petroleum (L.P.)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Part
Number
50326
Stamp
Code
44
51211
55
51
Section 7 Gas Burner Conversion Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
72. INSTALLATION INSTRUCTIONS FOR
56412 AND 56413 GAS KITS
WARNING
Failure to follow these gas conversion
instructions may result in conditions which
can produce bodily injury and/or property
damage.
a. Apply thumb pressure to the right side of access
door. When door opens, move door to the left to
disengage from door supports.
b. Disconnect igniter wires at quick disconnect
blocks.
c. Remove hex head screw (located on right side
of burner housing) holding burner tube and
igniter in place.
d. Carefully move burner tube toward rear of
dryer, far enough to permit removal of burner
orifice spud from orifice adapter.
NOTE: Tab on burner tube may have to be
removed from slot in burner housing to obtain
enough clearance.
56412 Gas Kit:
e. Turn burner orifice spud out of orifice adapter
and install No. 51211 L.P. Burner Orifice Spud
(metal stamped No. 55). Torque new burner
orifice spud to 15 inch-pounds (1.7 N-m).
f. Reinstall burner tube, tighten hex head screw
firmly and reconnect igniter leads.
g. Remove vent screw and install No. 53390
Block-Open Plug and Gasket.
h. Install No. 55753 “Valve Converted” Sticker to
top side of gas valve so it covers the gas valve
part number.
i. Install one of the No. 56426 L.P. Gas Stickers
over the old sticker on rear of cabinet, then
place the second sticker over the old sticker
located on backside of access door.
52
j. Apply the No. 53408 Change-Over Sticker to
the inside of the loading door opening above the
nameplate.
k. Connect electrical service and open valve in gas
supply line. Start dryer and observe burner
flame. Adjust air shutter to obtain a soft,
uniform flame. (A lazy, orange tipped flame
indicates lack of air. A harsh, roaring, very blue
flame indicates too much air.) Adjust air shutter
to obtain a soft uniform blue flame as follows:
(1) Loosen air shutter lockscrew.
(2) Turn air shutter to the right or left as
necessary to obtain proper flame intensity.
(3) After air shutter is adjusted for proper
flame, tighten air shutter lockscrew
securely.
l. Be sure and observe at least two complete
ignition and burn cycles before reinstalling
access door.
56413 Gas Kit:
m. Turn burner orifice spud out of orifice adapter
and install No. 50326 Natural Gas Burner
Orifice (metal stamped No. 44). Torque new
burner orifice spud to 15 inch-pounds (1.7 Nm).
n. Reinstall burner tube, tighten hex head screw
firmly and reconnect igniter leads.
o. Remove block-open plug and install No. 53952
Vent Screw and Gasket.
p. Install No. 56414 Valve Number Sticker to top
side of gas valve so it covers the gas valve
converted sticker.
q. Install one of the No. 56427 Natural Gas
Stickers over the old sticker on rear of cabinet,
then place the second sticker over the old
sticker located on backside of access door.
r. Apply No. 53556 Change-Over Sticker to
inside of the loading door opening above the
nameplate.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 7 Gas Burner Conversion Procedures
WARNING
To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the dryer(s) before servicing.
• Close gas shut-off valve to gas dryer(s) before servicing.
• Never start the dryer(s) with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be
reconnected to ensure that the dryer is properly grounded.
W001R1
s. Connect electrical service and open valve in gas
supply line. Start dryer and observe burner
flame. Adjust air shutter to obtain a soft,
uniform flame. (A lazy, orange tipped flame
indicates lack of air. A harsh, roaring, very blue
flame indicates too much air.) Adjust air shutter
to obtain a soft uniform blue flame as follows:
(1) Loosen air shutter lockscrew.
(2) Turn air shutter to the right or left as
necessary to obtain proper flame intensity.
(3) After air shutter is adjusted for proper
flame, tighten air shutter lockscrew
securely.
t. Be sure and observe at least two complete
ignition and burn cycles before reinstalling
access door.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
Section 8
Internal Wiring of Dryer Motor Switch
MAIN WINDING
BLU
START WINDING
OVERLOAD
PROTECTOR
BLK
ORG
4
3
5
S
S
R
R
4
1
2
6
5
DRY869S
GENERAL ELECTRIC
MAIN WINDING
YEL
START WINDING
OVERLOAD
PROTECTOR
BLK
BRN
4 BLU
7 BLK
S
S
R
R
4
1
5 YEL
2
6
5
DRY870S
EMERSON
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55
Section 9
Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
WIRING DIAGRAMS AND SCHEMATICS
FOUND ON THE FOLLOWING PAGES
ARE FOR MODELS COVERED IN THIS MANUAL.
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
57
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG9280 AND HG9260
58
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE9270 AND HE9250
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
59
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG7290 AND HG7009
Through Serial No. SH965992
60
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG7290 AND HG7009
Starting Serial No. SH965993
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
61
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE7230 AND HE7003
Through Serial No. SH965992
62
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE7230 AND HE7003
Starting Serial No. SH965993
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
63
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG6660, HG6380, HG4360 AND HG4280
64
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE6650, HE6370, HE4503, HE4430, HE4350, HE4330, HE4270 AND HE4203
Through Serial No. SH965992
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
65
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE6650, HE6370, HE4503, HE4430, HE4350, HE4330, HE4270 AND HE4203
Starting Serial No. SH965993
66
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG6494
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
67
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG6490 AND HG2490
68
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HE6434
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
69
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE6430, HE2430 AND HE2250
70
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG6360
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
71
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HE6350
72
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG6009
Through Serial No. SH965837
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
73
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG6009
Starting Serial No. SH965838
74
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HE6003
Through Serial No. SH965837
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
75
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HE6003
Starting Serial No. SH965838
76
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG5390
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
77
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HE5330 AND HE4030
78
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG5009
Through Serial No. SH965837
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
79
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG5009
Starting Serial No. SH965838
80
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE5003 AND HE2030
Through Serial No. SH965837
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
81
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE5003 AND HE2030
Starting Serial No. SH965838
82
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG4509, HG4490, HG4390 AND HG4209
Through Serial No. SH965992
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
83
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG4509, HG4490, HG4390 AND HG4209
Starting Serial No. SH965993
84
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG4109 AND HG4009
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
85
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE4103 AND HE4003
86
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG4080
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
87
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE4070
88
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE3060
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
89
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HG3009 AND HG2090
90
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODELS HE3003, HE2050, HE2030 AND HE2003
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
91
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG2980
92
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HE2970
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
93
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL HG2260
94
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53264
Section 9 Wiring Diagrams
WARNING
Failure to install, maintain, and/or operate this machine according to the manufacturer's
instructions may result in conditions which can produce bodily injury and/or property damage.
W030
MODEL FE0080
53264
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
95