Craftsman 917.248970 Owner`s manual

Owner's Manual
CRIIFTSMIIN°
GRASS CATC
E
42" Mower
Model No.
917.248970
\\\\\
• Safety
Assembly
Operation
, Maintenance
, Repair
Parts
CAUTION:
Read and follow all Safety
Rules and Instructions be-
For answers to your questions
about this product, Call:
fore operating this equipment.
Sears Craftsman Help Line
5 am - 5 pm, Men - Sat
1=800=659=5917
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman
website:www.sears.com/craftsman
SAFETY RULES
Safe Operation
Practices
for Ride=On Mowers
iMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS.
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
L GENERAL OPERATION
,,
,,
,,
,,
,,
,,
,,
,,
,,
,,
,,
,,
,,
,,
,,
,,
Read, understand, and follow all instructions in the manual
and on the machine before starting.
Only allow responsible adults, who are familiar with the
instructions, to operate the machine.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.
Be sure the area is clear of other people before mowing.
Stop machine if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary. Always
look down and behind before and while backing.
Be aware of the mower discharge direction and do not point
it at anyone. Do not operate the mower without either the
entire grass catcher or the guard in place.
Slow down before turning.
Never leave a running machine unattended. Always turn
off blades, set parking brake, stop engine, and remove keys
before dismounting.
Turn off blades when not mowing.
Stop engine before removing grass catcher or unclogging
chute.
Mow only in daylight or good artificial light.
Do not operate the machine while under the influence of
alcohol or drugs.
Watch for traffic when operating
near or crossing
roadways.
Use extra care when loading or unloading the machine into
a trailer or truck.
Data indicates that operators, age 60 years and above, are
involved in a large percentage of riding mower-related injuries.
These operators should evaluate their ability to operate the
riding mower safely enough to protect themselves and others
from serious injury.
Keep machine free of grass, leaves or other debris build-up
which can touch hot exhaust / engine parts and burn. Do not
allow the mower deck to plow leaves or other debris which
can cause build-up to occur. Clean any oil or fuel spillage
before operating or storing the machine. Allow machine to
cool before storage.
DO NOT:
,
,
,
,
Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine
and the mowing activity. Never assume that children will remain
where you last saw them.
,,
,,
Before and when backing, look behind and down for small
children.
,,
Never carry children. They may fall off and be seriously
injured or interfere with safe machine operation.
,,
,,
Never allow children to operate the machine.
Use extra care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
IV. SERVICE
,,
,,
Slopes are a major factor related to loss-of-control and tipover
accidents, which can result in severe injury or death. All slopes
require extra caution. If you cannot back up the slope or if you
feel uneasy on it, do not mow it.
,,
DO:
,,
,,
,,
,,
,,
,,
Keep children out of the mowing area and under the watchful
care of another responsible adult.
Be alert and turn machine off if children enter the area.
,,
,,
Mow up and down slopes, not across.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts, or bumps. Uneven terrain could overturn
the machine. Tall grass can hide obstacles.
Use slow speed. Choose a low gear so that you will not have
to stop or shift while on the slope.
Follow the manufacturer's recommendations for wheel weights
or counterweights to improve stability.
Use extra care with grass catchers or other attachments.
These can change the stability of the machine.
Keep all movement on the slopes slow and gradual. Do not
make sudden changes in speed or direction.
Avoid starting or stopping on a slope. If tires lose traction,
disengage the blades and proceed slowly straight down the
slope.
Do not turn on slopes unless necessary, and then, turn slowly
and gradually downhill, if possible.
Do not mow near drop-offs, ditches, or embankments. The
mower could suddenly turn over if a wheel is over the edge
of a cliff or ditch, or if an edge caves in.
Do not mow on wet grass. Reduced traction could cause
sliding.
Do not try to stabilize the machine by putting your foot on
the ground.
Do not use grass catcher on steep slopes.
III. CHILDREN
II. SLOPE OPERATION
,,
,,
,,
FAILURE
,,
,,
,,
,,
,,
Use extra care in handling gasoline and other fuels. They
are flammable and vapors are explosive.
Use only an approved container.
Never remove gas cap or add fuel with the engine running.
Allow engine to cool before refueling. Do not smoke.
Never refuel the machine indoors.
Never store the machine or fuel container inside where
there is an open flame, such as a water heater.
Never run a machine inside a closed area.
Keep nuts and bolts, especially blade attachment bolts, tight
and keep equipment in good condition.
Never tamper with safety devices. Check their proper operation
regularly.
Keep machine free of grass, leaves, or other debris buildup. Clean oil or fuel spillage. Allow machine to cool before
storing.
Stop and inspect the equipment if you strike an object. Repair,
if necessary, before restarting.
Never make adjustments
or repairs with the engine
running.
Grass catcher components are subject to wear, damage,
and deterioration, which could expose moving parts or
allow objects to be thrown. Frequently check components
and replace with manufacturer's recommended parts, when
necessary.
Mower blades are sharp and can cut. Wrap the blade(s) or
wear gloves, and use extra caution when servicing them.
Check brake operation frequently. Adjust and service as
required.
SAFETY RULES
&
,,
,,
,,
,,
,,
,,
Safe Operation
Practices
Be sure the area is clear of other people before mowing.
Stop machine if anyone enters the area.
Never carry passengers or children even with the blades
off.
Do not mow in reverse unless absolutely necessary. Always
look down and behind before and while backing.
Never carry children. They may fall off and be seriously
injured or interfere with safe machine operation.
Keep children out of the mowing area and under the watchful
care of another responsible adult.
Be alert and turn machine off if children enter the area.
,,
Before and when backing, look behind and down for small
children.
,,
,,
Mow up and down slopes (15 ° Max), not across.
Remove obstacles such as rocks, tree limbs, etc.
,,
Watch for holes, ruts, or bumps. Uneven terrain could overturn
the machine. Tall grass can hide obstacles.
Use slow speed. Choose a low gear so that you will not
have to stop or shift while on the slope.
Avoid starting or stopping on a slope. If tires lose traction,
disengage the blades and proceed slowly straight down the
slope.
,,
,,
,,
,,
for Ride=On Mowers
If machine stops while going uphill, disengage blades, shift
into reverse and back down slowly.
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
&
important safety precautions, it means
CAUTION!!!
Look for thisBECOMEALERT!!!
symbol to pointYOUR
out
SAFETY IS iNVOLVED.
I _
I
CAUTION: Do not coast down a hill
in neutral, you may lose control of
I
I
the tractor.
CAUTION: Tow only the attachments
that are recommended
by and
the manufacturer
of your tractor.
comply
with sense
specifications
Use
common
when towing.of
Operate only at the lowest possible
speed when on a slope. Too heavy
of a load, while on a slope, is
dangerous.
Tires can lose traction
with the ground and cause you to
lose control of your tractor.
accidental starting when setting
up,
transporting,in adjusting
making
CAUTION:
order to orprevent
repairs, always disconnect spark
plug wire and place wire where it
cannot contact spark plug.
CONGRATULATIONS on your purchase of a new Grass Catcher. It has been designed, engineered and manufactured to
give you the best possible dependability and performance.
Should you experience any problems you cannot easily remedy, please contact your nearest authorized service center/
department. They have competent, well trained technicians and the proper tools to service or repair this unit.
Please read and retain this manual. The instructions will enable you to assemble and maintain your Grass Catcher properly.
Always observe the "SAFETY RULES".
SAFETY RULES .........................................................
2=3
ASSEMBLY .................................................................
5=8
OPERATION ................................................................
10
CUSTOMER RESPONSiBiLiTiES ............................... 11
STORAGE ....................................................................
11
WARRANTY .................................................................
11
REPAIR PARTS .......................................................
12=13
KNOWYOUR
GRASS
CATCHER
READTHIS OWNER'S MANUALAND SAFETY RULES BEFORE ASSEMBLING OR OPERATINGYOU R GRASS CATCHER.
Compare the illustrations with the carton contents to familiarize yourself with the parts before starting the assembly. Study
the operating instructions and safety precautions thoroughly to insure proper functioning of your Grass Catcher and to
prevent injury to yourself and others. Save this manual for future reference.
SAFETY GLASSES
UNPACKING
•
•
The operation of any tractor can result in foreign objects thrown into the eyes, which can result in
severe eye damage. Always wear safety glasses or eye shields before starting your tractor and while
mowing. We recommend standard safety glasses or a wide vision safety mask worn over spectacles.
iNSTRUCTiONS
I
Remove all parts and packing materials from carton.
Check carton contents against list. Be sure all parts
are there.
CARTON
CONTENTS:
(2) Container Tops
(2) Container Bottoms
(1) Upper Chute
PARTS
(1) Lower Chute
(1) Support Assembly
(1) Cover Assembly
iDENTiFiCATiON
SUPPORT
ASSEMBLY
COVER
UPPER CHUTE
FULL
BAG
INDICATOR
CHUTE LATCH
-%
GRASS
CATCHER
CONTAINERS
LOWER CHUTE
ATTACHING
STRAPS
LOWER CHUTE
NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the
tractor, in the operator's position.
CAUTION:
_h)
BEFORE ASSEMBLING
GRASS CATCHER TO TRACTOR:
=
Depress clutch/brake
=
Place gearshift/motion
pedal fully and set parking brake.
•
=
•
Turn ignition key "OFF" and remove key.
Place attachment clutch in "DISENGAGED" position.
Make sure the blade and all moving parts have completely
•
Disconnect
with plug.
control
lever in neutral (N) position.
stopped.
spark plug wire from spark plug and place wire where it cannot come in contact
4
1
BAGGER SUPPORT ASSEMBLY
(See Fig. 1A)
Simply hang the support assembly on the bolts.If your tractor does not have four (4) shoulder bolts installed on the
drawbar, follow the instructions below.
SHOULDER
BOLTS
MOUNTING COVER ASSEMBLY TO
SUPPORT ASSEMBLY (See Fig. 2)
NOTE: For ease of assembly, you may wish to obtain the
assistance of another person for mounting cover assembly
to tractor.
t.
2.
Lift cover and align cover bracket with support
assembly.
Slide cover assembly
down onto the support
assembly.
SUPPORT
ASSEMBLY
TO REMOVETHE SUPPORT ASSEMBLY (See Fig. 1B)
1. Pull outward on the stop bracket enough to allow support
assembly to be lifted up and away from drawbar.
COVER
_"
ASSEMBLY
/
SUPPORT
ASSEMBLY
PULL OUT ON STOP BRACKETTO
REMOVE SUPPORT ASSEMBLY
=
02643
FiG. 1B
02646
FiG. 2
CONTAINER
1.
2.
ASSEMBLY
Place bottom half inside of top half, as shown.
Place one foot inside bottom half and lift top half to
meet bottom half.
3.
Press halves tightly together while lifting top to lock
into place as shown.
iMPORTANT:BEFORE LOCKINGTHE TABS,HOOKED EDGES
ONBOTH HALVESMUSTOVERLAPTOFORMSEALAS SHOWN
IN INSET.
4.
CONTAINER
(See Fig. 3)
1.
MOUNTING
(See Fig. 4)
install one container to left side first with warning to
outside of unit. install other container to right side.
NOTE: Right container should always overlap left container
at center support.
2.
Close cover and lock latch handle over center support
tube.
Repeat for other containers.
COVER LATCH
HANDLE
CONTAINER
BOTTOM HALF
--
CONTAINER
WARNING
CONTAINER
TOP HALF
CONTAINER
HANDLE
CONTAINER
TOP HALF
PRESS TOGETHER
TO FORM SEAL
WHILE LIFTING
TOP HALF
i
CONTAINER
BOTTOM
HALF
LOCKING
TAB
FiG. 3
ASSEMBLY CHECK: Squeeze sides of lower half of container and check that there is no gap between upper and
lower halves. If a gap appears, unlock tabs to separate
container halves and repeat instructions above.
CENTER
SUPPORT
TUBE
CONTAINER
WARNING
LOWER CHUTE = MOWER WiTH
MOUNTING TAB (See Fig. 5A)
1.
2.
3.
4.
•
Raise and hold deflector shield in upright position.
Place slot in Iowerchute over mounting tab on mowerand
position lower chute over mower opening as shown.
Hook rear latch into flange hole on back of mower.
Hook front latch into tab hole on front of mower.
If your tractor is equipped with gauge wheels on the
mower, then it will be necessary to hook the rear latch
into the hole in the R.H. gauge wheel bracket.
_lb
shield from mower. Raise and hold
CAUTION: Do not remove deflector
shield when attaching lower chute
and allow it to rest on chute while in
operation.
DEFLECTOR SHIELD
HINGE BRACKET
DEFLECTOR
SHIELD
03058
MOUNTING
TAB
REAR GAUGE
WHEEL
BRACKET
FRONT
LATCH
WITH REAR
GAUGE WHEELS
HEAH LATCH
REAR LATCH
WITHOUT
GAUGE WHEELS
FIG. 5A
LOWER
CHUTE
MOWER
WITHOUT
MOUNTING
TAB -(See
Fig. 5B)
1.
Lower mower deck to its lowest cutting position.
PLACE LOWER REAR EDGE
BETWEEN GAUGE WHEEL
BRACKET TAB AND
MOWER HOUSING,THEN
HOOK REAR LATCH
OPTIONAL
GAUGE
WHEEL
AND
BRACKET
NOTE: If equipped, remove mulch cover from mower deck
and store in a safe place.
2. With your right hand, raise and hold deflector shield in
upright position.
3. With your left hand, hold lower chute as shown and
position lower rear edge of chute between gauge wheel
bracket tab and mower housing, then carefully release
deflector shield and hook rear latch to mower deck.
4.
5.
6.
ALIGN CHUTE "B"
....................WITH MOWER "B"
Raise deflector shield and align "B" on lower chute
extended edge with "B" on mower housing.
With your right hand, push firmly on the lower chute
until the extended edge slides under the deflector shield
and along side the hinge bracket as shown.
With chute in proper position, hold the chute securely,
so it does not move, while hooking the front latch to
the mower deck.
NOTE: While hooking the latches, the deflector shield may
try to push the chute away from the mower deck opening.
It is important to hold the chute in position while hooking
the latches to the mower deck.
•
If your tractor is equipped with gauge wheels on the
deck, then it will be necessary to hook the rear latch
into the hole in the R.H. gauge wheel bracket.
guard from mower. Raise and hold guard
CAUTION:
Do not
discharge
when attaching
lowerremove
chute and
allow it
to rest on chute while in operation.
\
\
PUSHIN
DEFLECTOR SHIELD
HINGE BRACKET
EXTENDED EDGE "B"
Must be under deflector shield
and along side the hinge bracket
DEFLECTOR
SHIELD
\
REAR GAUGE
WHEEL
BRACKET
FRONT
LATCH
WiTH REAR
GAUGE WHEELS
REAR LATCH
WITHOUT
GAUGE WHEELS
REAR LATCH
UPPER CHUTE (See Figs. 6A & 6B)
No hardware required
1.
2.
Lower mower deck to its lowest cutting position.
Assemble upper chute by inserting curved end into
hole in back of cover.
NOTE: Handle carefully so as not to damage full bag indicator.
3.
Push in and turn upper chute until it is in line with lower
chute.
4.
Align the bosses on lower chute with alignment slots
on upper chute and slide together.
Secure with rubber latch by hooking hole in latch over
latch pin.
5.
FULLBAG
HANDLE
INBICATOR_
COVER
UPPER
CHUTE
LOWER
FiG. 6A
ALIGNMENT
SLOT
LATCH PIN
RUBBER
LATCH
BOSSES
FiG. 6B
LEVEL
No MOWER
hardware DECK
required
Be sure deck is properly leveled for best mower performance. See your tractors owner's manual for instructions.
TIPS FOR iMPROVED
OPERATION:
•
BAGGING
Follow the mower operation instructions in your tractor
owner's manual.
When operating your grass catcher on a lawn where grass
and leaf bagging equipment has not been used, you are
picking up thatch and debris that has accumulated for long
periods of time. The amount collected and the total time
of operation may be greater than you will experience with
regular use of your grass catcher.
•
•
Avoid cutting wet grass or in the morning while the dew
is still heavy. Grass clippings collected under these
conditions tend to be sticky and adhere to the walls of
the flow path causing clogging.
Your bagger is equipped with a full bagger indicator.
Movement of the wheel increases as the bags fill. The
wheel will be spinning fastest just before the bags fill
completely. When the wheel stops, it indicates that the
bags are full and the chutes have become clogged.
NOTE: To help prevent clogging of chutes, check/empty
bags when the wheel is spinning fast. Experience will teach
you the best time to empty the bags.
Care should be taken not to damage the parts and that
the wheel spins freely at the beginning of each use.
If the grass catcher fails to pick up cut grass or leaves,
it is an indication that clogging has occurred in the
system or that the grass catcher containers are full.
Usually this is indicated by the stopped movement of
the full bagger indicator.
a. Disengage blades, shift into neutral, engage the
parking brake and stop the engine.
- Raise seat. Unlatch and raise cover.
Always run throttle at full speed when bagging.
Select a gear low enough to give good mower cutting
performance, good quality cut and good bagging
performance.
NOTE: It may be necessary to overlap width of cut to suit
your conditions.
If grass is extremely tall, it should be mowed twice. The
first time relatively high, the second time to desired
height.
Use left hand side of mower for trimming.
Plastic trash bags can be inserted inside grass catcher
containers for ease of debris disposal. To remove the
plastic trash bags when full:
a. Disengage blades, shift into neutral, engage the
parking brake and stop the engine.
b. Raise seat. Unlatch and raise cover.
- Slide out containers and dispose of clippings.
- Replace containers, close cover, and latch.
b,
Unlatch chutes and check for clogging.
- Remove all debris in chutes.
- Reassemble and latch chutes
c. Remove one container at a time by grasping
container handles and pulling toward the rear, off
of the tube rails.
c. Checktoinsurefull
clogged.
baggerindicatorhasnotbecome
- The air passage hole must be clear of debris.
Gently insert a small twig or wire into passageway
to clear.
d. With the container resting on the ground, close
and secure the top of the plastic lawn bag.
e. Tip the container on its side and slide the filled bag
from the container.
f.
Install a new plastic lawn bag with the edges of the
bag draped over upper lip of the container.
g. Repeat for other containers.
h. Reinstall containers making sure right container
overlaps left container at center supports.
j. Close cover and secure latches over center support
tubes.
CAUTION
• Do not operate mower
partially installed.
with grass catcher
= Disengage blades and stop engine before
leaving tractor seat to empty containers,
unclogging chutes, etc.
• Close cover before starting.
= Disengage mower when crossing driveways
or gravel surfaces and other areas where
thrown objects could be a hazard.
• Do not attempt to vacuum up cans or other
potentially hazardous projectiles.
10
GENERAL
STORAGE
RECOMMENDATIONS
When grass catcher is to be stored for a period of time,
clean it thoroughly, remove all dirt, grass, leaves, etc. Store
in a clean, dry place.
Always observe safety rules when performing any maintenance.
•
Before each use check for loose fasteners.
Clean unit thoroughly after each use.
BLADE
containers.
Empty
containers
each
CAUTION: Do
not leave
grass after
in bagger
use and before storing. Failure to do so
may result in spontaneous combustion
which could develop into a fire.
CARE
For best results mower blades must be kept sharp. Replace
bent or damaged blades.
See BLADE CARE instructions in your tractor owner's
manual.
CAUTION: BEFORE PERFORMING ANY
MAINTENANCE, SERVICE OR ADJUST=
MENTS:
•
Depress clutch brake pedal fully and
set parking brake.
•
Place gearshift/motion
control lever in
"NEUTRAL" position.
Place clutch control in "DISENGAGED"
position.
•
•
Turn ignition key to "OFF" position.
•
Make sure blades and all moving parts
have completely stopped.
•
Disconnect
spark plug wire(s) from
spark plug(s) and place wire where it
cannot come in contact with plug.
CAUTION: Grass catcher components
are subject to wear, damage and
deterioration,
which could expose
moving parts or allow objects to be
thrown. Frequently checkcomponents
and replace with manufacturer's
recommended parts, when necessary.
One Year Full Warranty
on Craftsman
Grass Catcher
When assembled, used and maintained according to the owner's manual instructions, if this grass catcher fails
due to a defect in material or workmanship within one year from the date of purchase, RETURN IT TO ANY
SEARS STORE OR SEARS PARTS & REPAIR CENTER OR OTHER CRAFTSMAN OUTLET IN THE UNITED
STATES FOR FREE REPAIR (or replacement if repair proves impossible).
•
This warranty does not include the bagging blades, which are expendable parts.
•
This warranty is void if this grass catcher is used for commercial or rental purpose.
•
This warranty applies only while this product is used in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL. 60179
11
GRASS CATCHER-
- MODEL NUMBER
917.248970
2
5
8
20
10
20
38
t_ i I
39
18
20
20
15
21
20
14
15
33
31
24
31
27
28
31
36
25
GRASS CATCHER-
KEY
NO.
PART
NO.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
18
2O
21
69180
127533
171061
126840
18021008
130933
87175
19061216
7206J
60867
10071000
109808X
2029J
160493
162803
71161010
132796
DESCRiPTiON
- MODEL NUMBER
KEY
PART
NO.
NO.
917.248970
Nut, Crownlock #10-24
Screen, Cover
CoverAsm. (Incl. 3,38,39)
Chute, Upper
Screw, Special #10-14 x 1/2
Full Bagger Indicator
Screw, #10-24 x 1-1/8
Washer 3/16 x 3/4 x 16 Ga.
22
23
24
25
26
27
28
29
133235
132983
180923
73800400
4939M
72140405
179745
170165
Spacer, Split
Nut, Acorn #10-24
Washer, lock
Latch, Chute
Nut, Weld
Latch, Hook
Chute, Lower
Screw #10-24 x 5/8
31
32
33
34
35
36
38
39
174083
179746
192786
127534
183286
129586
130895
155042X431
Spring, Cover L.H. (black)
--
404327
DESCRiPTiON
Spacer, Cover
Spring, Cover R.H. (gray)
Support Assembly
Locknut
Spring, Retainer
Bolt
Bracket, Stop
Shoulder Bolt (Not Included with grass Catcher)
Plug, Tubing End
Bagger, Frame
Pin, Hinge
Gasket, Cover
Container, Top
Container, Bottom
Latch Handle, Cover
Strip, Reinforcement
Owner's Manual
NOTES
14
NOTES
15
iiiiiiiilHii
!iliiiiiiii!iH
iiiiiHi
_____
ii ii!iHiiiiiii
iii ii ili ii!iiiiiiiiiiiii
__
___ i ii:i ii!
iii
iiiiiii_ii_!!iiii_ii!!iiiii_iiii_iii_iiiii_!!iiii_i!!iiii_i_!!!_`
......
......
_!!!iiiiii!%!!%iiii!!iiiiii!iiiiiiiii!!!!iiiiiiii
_'_'_,','_i!!iiiiiiiiiiiiiiiii!!i_iiiiiiiiiiiii!!!!_iii
iiiiiiiiiiiilHiiiiii!!iiiii!!iiiiii!!i}iiii!!iiiiiii!!iiiiii_'
.....
_'_ii!!_!iiiiiii!iiiiiiiiiiiiiii_ii
Your Home
Hiiiiiiiiiiiiiii!!iiiii!iiiiiiiiiiiiiiiiiiiiiiiii!i_
_'
iiiiiiii!iiiiiiiiiilHiiiii!!!iiiiiiiiiiiiilHi_
_''_
iiiiiiii!iiiiii!!_iiiiiiiiiiiiiiiii!_
_
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
iiiiiiii!iii!!i!!iiiiiiiiiiiii_'
iiiiiiiiiiii!!iii!!iiiiiiiiiii_
_
i_iiiiiiiiiiiiiiii!!iiiii!i
H_
iiiiii_iiiiiiiiiiii!!iii_
iiiiiiiiiiiiiiiiiiiiii_i!
iiiiii_imiiiiiiiiii!!ii
i_iiii!iii!!iiiiiiiiiiiill
iiiiiiiiiiii_iiiiiiiiiiil
iiiiiiii!iiiiii!!_mi_i
i_iiiiiiiiii!!iiiiii!!iiii
iiiiii_iiiiiiiii!!iiiii!_
iiiiiiiiiiiiiiiiiiiiii_ii
iiiiii_ii_iiiiiiiiiiiii!
i_iiiiiiiiiiiiiiiiiiii!!ii
iiiiii!_i!!iim_iiiiiil
iiiiiiii!iii_i!!iiiiiiiii
iiiiiiiiiiii!!iii_i_mi
i_iiiiiiiiiiiiiii!!iiiii!i
iiiiii_iiiiiiiiiiii!!iii_
iiiiiiiiiiiiiiiiiiiiii_i!
iiiiii_imiiiiiiiiii!!ii
i_iiii!iii!!iiiiiiiiiiiill
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional
installation of home appliances
and items like garage door openers and water heaters.
iiiiiiiiiiii_iiiiiiiiiiil
iiiiiiii!iiiiii!!_mi_i
i_iiiiiiiiii!!iiiiii!!iiii
iiiiii_iiiiiiiii!!iiiii!_
iiiiiiiiiiiiiiiiiiiiii_ii
iiiiii_ii_iiiiiiiiiiiii!
i_iiiiiiiiiiiiiiiiiiii!!ii
iiiiii!_i!!iim_iiiiiil
iiiiiiii!iii_i!!iiiiiiiii
iiiiiiiiiiii!!iii_i_mi
i_iiiiiiiiiiiiiii!!iiiii!i
iiiiii_iiiiiiiiiiii!!iii_
iiiiiiiiiiiiiiiiiiiiii_ii
iiiiii_imiiiiiiiiiiiiii
i_iiii!iii!!iiiiiiiiiiiill
....
iiiiiiiiiiiiiiiiiii_iiiiiiiiii
iiiiiiiiiiiiiiiiiii_iiiiiiiiii
1-800-4-MY-HOME ®
(1-800-469-4663)
www.sears, corn
Anytime,
day or night
(U.S.A, and Canada)
www.sears, ca
Our Home
For repair of carry-in products like vacuums, lawn equipment,
and electronics, call or go on-line for the nearest
Sears Parts and Repair Center.
1-800-4884
222
Anytime,
ii_iiiiiiiiiiiiiiiiiiiiiiiiiiill
_
ii_iiiiiiiiiiiii!iiiiiii!!iii!!!
ii_iiiiiiiiiiiiiiiii!!iiii!iiill
ii_iiiiiiiiiiiiii!!iiiiiiiiiiiii
day or night (U.S.A. only)
i_iiiiiiiiiii!!ii!!ii!!ii!!iii
www.sears.com
ili!_iii
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
ili!_iii
1-800-827-6655
(U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
i_iiiiiiiiiiiiiiiiii!!iii!!iii!i, I..888-SU-HOGAR ®
i_i!!iiiii_iiii!iiii!iiiiiiiiiiiiii_
(t -888-784-6427)
::_iii!iiiiiiiiiii!iiiiiiiiHii!iiii!!!_
....
1-800-361-6665
iiiiiii
ii iiiiii
(Canada)
AuCanadapourserviceenfran£sais:
iiiiiiiiiiiiiiiii!!!iiii!iiii!iii!ii
1-800-LE-FOYER Mc
,iiiilHiiiiiiiiiii!iiiii!iii!ii
(1-800-533-6937)
www.sears.ca
,,iii!!iiiiiiiiiii!i!iiiiiiiiiii!!!i
i
,_iiiiiiiii!!iiiiiii!!iiiiiiiiii!!ii!!_
,_iiiiiiiiii!!ii!!iiiiiiiiiii!!!!iiiiii!i
!_
_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii!!iiiiii!
_
_iiiiiiiiiiiiiiiiiiiiiiiiiii!!iiiiiiiiiiiii!
_
_iiiiiiiiiiiiiiiiiiiiiii_iiiiiiiiiiiiiii_,,
_i!!!!iiiiii!iiiiiiii!!i!iiiiiiiii!!iiiiiiiii_
....
_"HH,,"HHH,,::"HHH_'HHHHHH_,
....
.....
_ii!i!i,iiiiiiiiiiiiii!!!!iiiiiii!!iiiiiiii!!iiiiiiiiiiiiiiiiiiiiiiii_
................
@ Sears Brands, LLC
® Registered Trademark / TM Trademark / SMService Mark of Sears Brands, LLC
® Marca Registrada / TMMarca de F_brica / SM Marca de Servicio de Sears Brands, LLC
MCMarque de commerce / MDMarque deposee de Sears Brands, LLC
404327 01.24.06
rad
PRINTED IN U.S.A.