FP2600-T41
User Manual
Digital Electronics Corporation
Preface
Thank you for purchasing Digital’s TFT type color display panel, the 'FP2600-T41'
(hereafter referred to as the FP unit).
The FP unit is a TFT type color liquid crystal display monitor for IBM-PC compatible
personal computers (SVGA mode).
Please read this manual completely to insure the correct use and complete understanding of the FP unit's functions. The FP's analog interface is designed for use with
standard VGA mode. Please be aware that this unit may not be able to be connected
with nonstandard VGA modes. For more details, please refer to this manual's "PC
Connectivity Notes" section.
The term FP2600-T41 refers to the following unit:
FP2600-T41-24V
(AC 24V type)
<Note>
It is forbidden to copy the contents of this manual, in whole or in part, except for the
user's personal use, without the express permission of the Digital Electronics Corporation of Japan.
2) The information provided in this manual is subject to change without notice.
3) This manual has been written with care and attention to detail; however, should you
find any errors or omissions, please contact Digital Electronics and inform them of
your findings.
4) Please be aware that Digital Electronics is not responsible for any damages resulting
from the use of our products, regardless of article 3 above.
5) Specifications set out in this manual are for overseas products only, and, as a result,
some differences may exist between the specfications given here and the Japanese
ones.
All Company/Manufacturer names used in this manual are the registered trademarks of
their respective companies.
©2001, Digital Electronics Corporation
FP2600-T41 User Manual
i
For the Safe And Correct Use of this Unit:
This manual describes safety instructions for correct use of the FP unit. Please keep this
manual close at hand, and refer to it when necessary.
The following symbols are used throughout this manual to ensure the safe use of the FP
unit. Please make sure to follow all instructions given since they explain important safety
points.
Warning
This mark warns of a situation that could either seriously
injure a person or lead to death if the instruction is ignored
and/or the unit is used incorrectly.
Caution
This mark warns of a situation that could either injure a
person or damage property if the instruction is ignored and/
or the unit is used incorrectly.
Other Symbols Used In This Manual
The list below describes the symbols used in this manual.
Explains a situation that requires a moderate amount of caution.
Indicates a word or phrase that has an additional explanation.
*1
A reference point. Describes the word or phrase marked by the asterisk (*) and the corresponding number.
Reference pages on related topics.
1),2)
ii
Operational steps. Please follow these numbered steps in order to
perform the desired operation.
FP2600-T41 User Manual
Warning
Safety Instructions
For the safe use of this unit, be sure to follow these guidelines:
Because of the ever present danger of electrical shock, be sure to unplug the power cable
from the FP unit before plugging the cable's other end into the wall.
Do not use power in excess of the unit's specified voltage range since it may cause a fire or
electric shock.
Because the FP unit contains high voltage parts, an electric shock can occur when disassembling the unit. Therefore, please be sure to always unplug the unit before disassembling
it.
Do not modify the FP unit in any way, since it may cause a fire or electric shock.
When changing the backlight, be sure to turn off the unit's power first, in order to prevent an
electric shock.
Do not use touch panel keys to perform life-threatening or vitally important safety functions.
Use separate mechanical switches for such keys.
If substantial amounts of metallic dust, water or liquids enter the FP unit, turn off the power
supply immediately, unplug the power cord, and contact your local FP distributor.
When installing the FP unit, be sure to follow the instructions given in “Chapter 3. Installation
and Wiring," to insure it is done correctly.
Do not use the FP in an environment with flammable gas since it may cause an explosion.
FP2600-T41 User Manual
iii
Caution
Safety Instructions
For the correct use of this unit, please follow these guidelines:
Do not press the screen's touch surface too strongly with either your finger or a hard
object, since the touch surface may be damaged.
When the surface of the display screen becomes dirty or smudged, clean the display with
a cloth soaked in a neutral detergent. Do not use paint thinner or organic solvent.
Do not press on the touch panel's face with sharp objects, such as a mechanical pencil or
screwdriver, since it might damage the LCD panel.
Avoid using or storing the FP in direct sunlight, excessively dusty or dirty environments, or
where chemicals or their vapors are present in the air.
Avoid restricting the FP's natural ventilation, or storing and using the FP in an environment
that will increase the FP's internal temperature.
Please avoid using the FP in areas where sudden, large changes in temperature may occur.
These changes can cause condensation to form inside the unit, possibly causing an accident.
Notes on the FP's Liquid Crystal Display (LCD)
The FP's LCD contains a strong irritant. If the panel is ever cracked and the LCD's liquid
contacts your skin, be sure to wash it with running water for at least 15 minutes. If any of
this liquid should enter your eye, be sure to flush the eye with running water for more than
15 minutes, and see a doctor immediately.
The current brightness of the LCD screen will depend on the screen's current display and
the LCD's contrast adjustment. Any brightness variations that result are normal for LCD
displays.
There are minute grid-points on the LCD surface. These points are not defects.
Sometimes crosstalk (shadows appearing on extended display lines) will appear on the
display. This phenomenon is a common attribute of LCD's and is not a defect.
The displayed color will look different when viewed from an angle outside the specified
view angle. This is also normal.
Displaying a single screen image for long periods of time can cause an afterimage to
remain. To correct this, turn the unit OFF for 5 or 10 minutes, then ON again. This
phenomenon is a common attribute of the LCD's, and not a defect. To prevent this effect,
you can:
- use the Display OFF feature, if the same image is to be displayed
for a long period of time.
- change the screen display periodically to prevent the displaying of a
single image for a long period of time.
iv
FP2600-T41 User Manual
Table of Contents
Preface ........................................................................................................................ i
For the Safe and Correct Use of this Unit .................................................................. ii
Warning: Safety Instructions ....................................................................................... iii
Caution: Safety Instructions ........................................................................................ iv
Table of Contents ........................................................................................................ v
When Connecting to a PC ........................................................................................... vii
FP2600-T41 Features .................................................................................................. viii
Package Contents ....................................................................................................... ix
UL/c-UL (CSA) Application Notes ........................................................................... x
CE Marking Notes ...................................................................................................... x
Chapter 1—Introduction
1-1 Connecting the FP to a PC .................................................................................. 1-1
1-2 Optional Equipment ............................................................................................... 1-2
Chapter 2—Specifications
2-1 General Specifications (For DC24V) ................................................................... 2-1
1 Electrical Specifications .............................................................................................. 2-1
2 Environmental Specifications ..................................................................................... 2-1
3 Structural Specifications ............................................................................................. 2-2
2-2 Functional Specifications(For DC24V) ................................................................. 2-3
2-3 Interface Specifications(For DC24V) ................................................................. 2-4
1 Analog RGB Interface ................................................................................................. 2-4
2 Serial Interface ............................................................................................................ 2-6
3 USB Interface .............................................................................................................. 2-7
2-4 Cable Diagrams ................................................................................................... 2-8
1 Pin Connections for the RGB Interface Cable ............................................................ 2-8
2 Pin Connections for the SIO Interface Cable ............................................................. 2-9
3 Pin Connections for the USB Interface Cable ........................................................... 2-9
2-5
Names and Functions of FP Parts ..............................................................
2-10
2-6
Flat Panel (FP) Dimensions ........................................................................
1 External Dimensions (DC24V) ...................................................................
2-11
2 Installation Brackets ...........................................................................................
3 FP Installation Dimensions .................................................................................
FP2600-T41 User Manual
2-11
2-12
2-12
v
Chapter 3—Installation and Wiring
3-1 Installation .................................................................................................................3-1
3-2 Wiring ........................................................................................................................3-5
1 Power Cable Connection ................................................................................................... 3-5
2 Precaoutions: Connecting the Power Supply .................................................................... 3-6
3 Precautions: Grounding ..................................................................................................... 3-7
4 Precautions: Input/Output Signal Lines ............................................................................ 3-7
3-3 Operation Mode Setup and Display Positioning .......................................................3-8
1 Operation Mode Setup and Adjustment ...............................................................3-8
2 Front LED Option Mode Display ..................................................................................... 3-9
3 Display Position Compensation by OSD .......................................................................... 3-10
Chapter 4—Touch Panel Commands
4-1
Command List ..........................................................................................................4-1
4-2
Boot-up Initialization ................................................................................................4-2
4-3
Touch Interface Data ..............................................................................................4-3
4-4
Touch Panel Commands ..........................................................................................4-5
Chapter 5—Troubleshooting
5-1
Troubleshooting ........................................................................................................ 5-1
1 Possible Device Problems ................................................................................................ 5-1
2 No Display ........................................................................................................................ 5-2
3 Touch Panel Does Not Work ............................................................................................ 5-4
Chapter 6—Maintenance
6-1
Regular Cleaning ..................................................................................................... 6-1
1 Cleaning the Display ........................................................................................................ 6-1
2 Installation Gasket Check/Replacement ........................................................................... 6-1
6-2
Periodic Check Points ............................................................................................. 6-2
6-3
Replacing the Backlight ........................................................................................... 6-3
INDEX............................................................................................. i - iv
vi
FP2600-T41 User Manual
When Connecting to a PC
The FP unit's analog interface is designed for standard SVGA mode. The number of dots
(pixels) displayed are as follows:
Size
800 X 600
800 X 600
640 X 480
640 X 480
640 X 480
640 X 400
640 X 400
640 X 350
720 X 400
720 X 350
H Sync.
35.156±1 KHz
37.879±1 KHz
31.469±1 KHz
35.000±1 KHz
37.861±1 KHz
24.827±1 KHz
31.469±1 KHz
31.469±1 KHz
31.469±1 KHz
31.469±1 KHz
V Sync.
56±1 Hz
60±1 Hz
60±1 Hz
66±1 Hz
72±1 Hz
56±1 Hz
70±1 Hz
70±1 Hz
70±1 Hz
70±1 Hz
Dot Clock Range
36.000MHz±1%
40.000MHz±1%
25.175MHz±1%
30.240MHz±1%
31.500MHz±1%
21.053MHz±1%
25.175MHz±1%
25.175MHz±1%
28.322MHz±1%
28.322MHz±1%
• With vertical 350 pixels, 400 pixels, including 50 pixels at the top and at the
bottom of the screen will be enlarged and displayed at 600 pixels (1.5 times).
Some types of VGA equipment may not be within the ranges specified above, and, therefore,
cannot be connected to the FP.
Also, if the user changes his PC's VGA board, there is the possiblity that the new board
may not be able to be connected to the FP.
FP2600-T41 User Manual
vii
FP2600-T41 Features
The features of the FP2600-T41 are as follows.
High Quality TFT Color LCD Display
This unit is equipped with a 12.1 inch TFT type color LCD. Its superior brightness and
wide viewing angle, not found in ordinary laptop type TFT LCD's, widens your scope of
applications.
The screen's maximum resolution is 800 x 600 pixels, and can display 260,000 colors.
Easy Installation In User’s Cabinets and Panels
The FP2600-T41's slim, lightweight, and compact design make installation a snap. It
was designed specifically for use as your IA (Industrial Automation) or OA (Office
Automation) system monitor. The flat, front panel provides protection equivalent to the
rigorous IP65F standard, and, even without its optional protective cover, the front panel
is highly resistant to both water and dust.
Panel can be used as a VGA Display
Since the FP2600-T41 is equipped with an analog RGB interface, it can be connected
to any PC with standard VGA/SVGA mode. (The PC's clock frequency, however,
must be within the standard range)
Easy to use Built In Touch Panel
The FP2600-T41's built in touch panel is standard equipment, allowing touch panel data
to be output to a host PC via input/output commands and an RS-232C cable and USB
cable. This is perfect for systems requiring both touch panel operation and data monitoring.
viii
FP2600-T41 User Manual
Package Contents
The FP's packing box contains the items listed below. Please check to be sure each is
included and is not damaged.
FP unit (FP2600-T41-24V)
FP2500/2600
User Manual (Contained in plastic case)
User Manual
Installation Gasket (1)
Installation Brackets (4)
FP2500-T41/FP2600-T41
Installation Guide (1)
Installation
Guide
These items have all been carefully packed with special attention to product quality.
However, should you find anything damaged or missing, please contact your local
distributor immediately for prompt service.
FP2600-T41 User Manual
ix
UL/c-UL (CSA) Application Notes
The FP2600-T41-24V is a UL/c-UL (CSA) listed product. (UL file No.E182139)
This unit conforms as a product to the following standards:
This UL508 Industrial Control Equipment
This UL1604 Electrical Equipment for use in Class 1 & 2 - Division 2, or Class 3
Hazardous Locations.
This CAN/CSA-C22.2, No.1010-1
MSUREMENT AND CONTROL EQUIPMENT
(Safety requirements for electrical equipment for mesurement and laboratory use)
FP2600-T41-24V(UL Registration Model: 30B0003-02)
<Cautions>
The FP must be used as a built-in component of an end-use product.
This unit should be installed in the front face of a metal panel.
If this unit is installed so as to cool itself naturally, be sure to install it in a vertical panel.
Also, be sure that the FP unit is mounted at least 100 mm away from any adjacent
structures or equipment. If these requirements are not met, the heat generated by the FP
unit's internal components may cause the unit to fail to meet UL/c-UL standard
requirements.
UL1604 Conditions of Acceptability and Handling Cautions:
1. Power, input and output (I/O) wiring must be in accordance with Class I,
Division 2 wiring methods-Article 501-4(b) of the National Electrical Code, NFPA
70 within the United States, and in accordance with Section 18-152 of the Canadian
Electrical Code for units installed within Canada.
2. Suitable for use in Class I, Division 2, Groups A, B, C and D, Hazardous Locations.
3. WARNING: Explosion hazard - substitution of components may impair suitability for
Class I, Division 2.
4. WARNING: Explosion hazard - when in hazardous locations, turn power OFF before
replacing or wiring modules.
5. WARNING: Explosion hazard - do not disconnect equipment unless power has been
switched OFF, or the area is known to be non-hazardous.
CE Marking Notes
The FP2600-T41-24V is a CE marked product that conforms to EMC directives
EN55011 class A and EN61000-6-2.
*For detailed CE marking information, please contact your local FP distributor.
x
FP2600-T41 User Manual
Chapter 1
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
1. Connecting
the FP to a PC
12345678901234567890123456789012
12345678901234567890123456789012
2. Optional
Equipment
12345678901234567890123456789012
12345678901234567890123456789012
Introduction
The following diagram illustrates the connection between the FP unit and a PC.
1-1 Connecting the FP to a PC
FP2600-T41 unit
1 Analog RGB Interface Cable
(FP-CV00<2.5m>,FP-CV01<5m>)
(VGA standard: Dsub 15-pin male)
B type
2 USB Interface Cable (5m)
(FP-US00)
(A-B type Cable)
1
2
3
3 SIO Interface Cable (5m)
(FP61V-IS00-O)
(Straight Cable: Dsub 9-pin female)
A type
Personal Computer
(PC)
FP2600-T41 User Manual
1-1
Introduction
1-2 Optional Equipment
All optional items listed below are products of Digital Electronics Corporation.
Item
Interface
SIO Cable
FP61V-IS00-O
RGB Cable
FP-CV00
FP-CV01
USB Cable
FP-US00
Backlight
Bulbs
Installation
Maintenance
Brackets
Parts
Rubber
Gasket
Optional
Parts
Model
Description
Serial interface cable (5m) used for touch
panel data transmission between the host
and the FP or command transmission to
the FP. This is a straight Dsub9 pin
female cable.
Analog RGB interface cable when image
signal is output to the FP from the host.
VGA specifications (Dsub15 pin male)
FP-CV00 (2.5m), FP-CV01 (5m)
USB interface cable (5m) used for touch
panel data transmission between the host
and the FP or command transmission to
the FP.
A-B type cable.
PS600-BU00
Replacement Backlight bulbs .
GP070-AT01
Metal installation brackets for FP2600-T41
GP-WP10-MS
Cover
Sheet
(Hard type)
PSL-DF00
Mouse
Emulator V2
PL-TD000
Replacement rubber gasket, used when
installing the FP. Same as the FP's
original gasket.
Provides disposable screen protection from
dust and other elements. The touch panel
can be used with the Cover Sheet attached
(5 sheets / set)
Mouse Emulator software for FP.*
* Operation environment is Windows®95, WindowsNT®4.0, Windows®98, Windows®2000.
When you use PL-TD000, hardware settings can not be automatically detected.
As a result, select the FP unit's currently connected COM Port, and enter the
settings given in the FP manual for the Allocated I/O address and Interrupt.
1-2
FP2600-T41 User Manual
Chapter123456789012345678901234567890121
2
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
1. General
Specifications
4. Cable Diagrams
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
2. Functional
Specifications 5. Names and Functions of FP Parts
123456789012345678901234567890121
Specifications
3. Interface Specifications
6. Flat Panel (FP) Dimensions
2-1 General Specifications
(For DC24V)
2-1-1 Electrical Specifications
Rated Voltage
Rated Voltage Range
Power Consumption
In-Rush Current
Voltage Endurance
Insulation Resistance
DC24V
DC 19.2V to DC 28.8V
50W or less
30A or less
AC1000V 20mA for 1minute
(between charging and FG terminals)
10M Ω or higher at DC500V
(between charging and FG terminals)
2-1-2 Environment Specifications
DCV24V (FP2600-T41)
Operating Temperature
0 oC to 50 oC
Storage Temperature
Humidity
-10 oC to 60 oC
30 to 85%RH (non-condensing)
Vibration Endurance
Noise Immunity
19.8m/s2 - 10 to 25 Hz (X,Y,Z directions - 30 minutes each)
Noise voltage: 1200 Vp-p
Pulse length: 1 µs
Rise time (rise/fall): 1 ns
Not immune to corrosive gas
Less than 100Ω, or your country's applicable standard
Equivalent to IP65f (JEM1030)
Pollution Level
Grounding
Protection*1
*1 (See the next page's note)
FP2600-T41 User Manual
2-1
Specifications
*1 (Continued from previous page)
The front face of the FP unit, installed in a solid panel, has been tested using
conditions equivalent to the standard shown in the specification . Even though
the FP unit’s level of resistance is equivalent to the standard, oils that should
have no effect on the FP can possibly harm the unit. This can occur in areas
where either vaporized oils are present, or where low viscosity cutting oils are
allowed to adhere to the unit for long periods of time. If the FP’s front face
protection sheet becomes peeled off, these conditions can lead to the ingress of
oil into the FP and separate protection measures are suggested. Also, if nonapproved oils are present, it may cause deformation or corrosion of the front
panel’s plastic cover. Therefore, prior to installing the FP be sure to confirm the
type of conditions that will be present in the FP’s operating environment.
If the installation gasket is used for a long period of time, or if the unit and its
gasket are removed from the panel, the original level of the protection cannot be
guaranteed. To maintain the original protection level, you need to replace the
installation gasket regularly.
2-1-3 Structural Specifications
DC24V (FP2600-T41)
External Dimensions
Weight
Cooling System
2-2
317W x 243H x 58D mm
3.5 kg or less
Natural air circulation
FP2600-T41 User Manual
Specifications
2-2 Functional Specifications
(For DC24 V )
Display Media
Display Size
Display Area (mm)
Resolution
Display Colors
T FT Active matrix color LCD
31cm (type 12.1) Opposite angle
246.0W × 184.5H
800(H)×600(V)pixels(1pixel=R+G+B pixel)
262,144 colors (R/G/B Six bits each)
Brightness
200cd/m 2 (typ)*1
0.33H×0.33W
Resolution: 1024×1024
Method: Resistive Film (Analog)
SVGA graphic & T ext mode
800×600,640×480,640×400,640×350,720×400,720
×350 mode display available.
However, with 350 pixels, 400 pixels, including 50
pixels at the top and bottom will be enlarged and
displayed as 680 pixels (1.5 times).
Dot Pitch (mm)
T ouch Panel
Display Mode
Interfaces
Backlight
Analog RGB Interface
SIO Interface(touch Interface)
USB Interface(touch Interface)
Backlight can be changed.
Lifetime : 50,000 hours when continuously lit (*2) at
25o C.
*1 The brightness at central part of the screen when displaying all white.
*2 2.5 times decreased brightness may be the life span, but this value is only for
reference and not a guaranteed value.
FP2600-T41 User Manual
2-3
Specifications
2-3 Interface Specifications
(For DC24V)
2-3-1 Analog RGB Interface
Input signal type
Analog RGB
Input signal characteristic
Image signal: analog RGB
Synchronous signal: TTL level, negative true or
positive true
Scanning type: non-interlace
Setting by OSD (On Screen
Display)
S iz e
800
800
640
640
640
640
640
640
720
720
X 600
X 600
X 480
X 480
X 480
X 400
X 400
X 350
X 400
X 350
Contrast Adjustment
Sub Contrast Adjustment
Brightness Adjustment
Horizontal Display Position Adjustment
Vertical Display Position Adjustment
Horizontal Adjustment
Phase Adjustment
Dimmer Adjustment
Default Setting (All Clear Function)
H S ync.
35.156±1
37.879±1
31.469±1
35.000±1
37.861±1
24.827±1
31.469±1
31.469±1
31.469±1
31.469±1
KHz
KHz
KHz
KHz
KHz
KHz
KHz
KHz
KHz
KHz
V S ync.
56±1
60±1
60±1
66±1
72±1
56±1
70±1
70±1
70±1
70±1
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Hz
Dot Clock Ra nge
36.000M H z±1%
40.000M H z±1%
25.175M H z±1%
30.240M H z±1%
31.500M H z±1%
21.053M H z±1%
25.175M H z±1%
25.175M H z±1%
28.322M H z±1%
28.322M H z±1%
• With vertical 350 pixels, 400 pixels, including 50 pixels at the top and
at the bottom of the screen will be enlarged and displayed at 600
pixels (1.5 times).
2-4
FP2600-T41 User Manual
Specifications
Pin Assignments and Signal Names for Analog RGB
Pin
No.
Signal Name
Condition
1
Analog R
R signal input
2
Analog G
G signal input
3
Analog B
B signal input
4
Reserved
NC (spare for input)
5
Digital grounding
Digital signal GND
6
Return R
R signal GND
7
Return G
G signal GND
8
Return B
B signal GND
9
Reserved
NC (spare for input)
10
Digital grounding
Digital signal GND
11
Reserved
NC (spare for input)
12
Reserved
NC (spare for input)
13
H. SYNC
Horizontal synchronous
signal input
14
V. SYNC
Vertical synchronous
signal input
15
Reserved
NC (spare for input)
Pin Location
15
5
11
1
Connector:
Mini Dsub 15 pin type
Connector set screw: Inch type (4-40)
FP2600-T41 User Manual
2-5
Specifications
2-3-2 Serial Interface
Serial Interface
Baud rate: 9600 bps
Data length: 8 bits
Parity: none
Stop bit: 1
Pin Assignments and Signal Names for Serial Interface
Pin
No.
Signal
Name
Condition
1
CD
Carrier Detect (FP->Host)
2
RD
Receive Data (FP->Host)
3
SD
Send Data (FP<-Host)
4
DTR
Data Terminal Ready (FP<-Host)
5
GND
Ground
6
DSR
Data Set Ready (FP->Host)
7
RS
Request to Send (FP<-Host)
8
CS
Clear to Send (FP->Host)
9
NC
No connection
Pin Location
6
9
1
5
Connector:
Dsub 9 pin female
Connector set screw: Inch type (4-40)
Concerning Signal Names
Signal names used for the serial interface on FP units are designed to match
the pin order used on most PC serial interfaces, so that a straight cable can
be used to connect the two. Therefore, connect each pin's signal to the same
signal name on the PC side.
For example, pin #2 'RD' should be connected to the 'RD' input terminal on
the PC's connector.
Refer to section "2-4 Cable Diagrams" for each signal's direction.
2-6
FP2600-T41 User Manual
Specifications
2-3-3 USB Interface
Pin Assignments and Signal Names for USB Interface
Pin
NO.
1
2
3
4
Signal
Name
USB1-5V
USBD1(-)
USBD1(+)
GND
Condition
+5VIN
USBdata(-)
USBdata(+)
Ground
Communication
Connector:
FP2600-T41 User Manual
Pin Location
1
2
3
4
Low speed Device
B type connector
2-7
Specifications
2-4
Cable Diagrams
2-4-1 RGB Interface Cable Pin Connections
FP side
RGB cable
PC side
1
RED IN
2
GRIN IN
3
BLU IN
4
NC
5
GND
6 RED GND
7 GRN GND
8 BLU GND
9
NC
10
GND
11
NC
RED VIDEO
GRN VIDEO
BLU VIDEO
NC
GROUND
GROUND RED
GROUND GRN
GROUND BLU
NC
GROUND
MONITOR
SENSE(COLOR)
1
2
3
4
5
6
7
8
9
10
11
--
12
NC
MONITOR
SENSE(MONO)
12
Input
Input
---
13
14
15
FG
HSYN
VSYN
NC
FG
HSYN
VSYN
NC
FG
1
2
3
4
5
6
7
8
9
10
11
Analog R
Analog G
Analog B
Reserved
Digital ground
Return R
Return G
Return B
Reserved
Digital ground
Reserved
Input
Input
Input
---------
12
Reserved
13
14
15
FG
H.SYNC
V.SYNC
Reserved
FG
Output
RED VIDEO
Output
GRN VIDEO
Output
BLU VIDEO
-NC
-GROUND
-GROUND RED
-GROUND GRN
-GROUND BLU
-NC
-GROUND
-MONITOR
SENSE(COLOR)
--MONITOR
SENSE(MONO)
13 Output
14 Output
15
-FG
HSYN
VSYN
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Signal names for the FP's RGB interface are designed to match the same pin order as
the RGB interface on personal computers.
2-8
FP2500-T41 User Manual
Specifications
2-4-2 Pin Connections for the SIO Interface Cable
FP side
SIO cable
PC side
1
CD
Output
1
CD
CD
1
Input
CD
1
2
RD
Output
2
RD
RD
2
Input
RD
2
3
SD
Input
3
SD
SD
3
Output
SD
3
4
DTR
Input
4
DTR
DTR
4
Output
DTR
4
5
GND
--
5
GND
GND 5
6
DSR
Output
6
DSR
DSR
6
Input
DSR
6
7
RS
Input
7
RS
RS
7
Output
RS
7
8
CS
Output
8
CS
CS
8
Input
CS
8
9
NC
--
9
NC
RI
9
Input
RI
9
FG
FG
--
FG
FG
FG
9
--
GND 5
Signal names for the FP's SIO interface are designed to match the same pin order as
the SIO interface on a standard PC.
2-4-3 Pin Connections for the USB Interface Cable
FP side
1 +5VIN
2 USB3 USB+
4 GND
Input
PC side
USB cable
Output
+5VIN
Input/Output USBInput/Output USB+
1
Input/Output
Input
+5VIN
2 USBInput/Output
3 USB+ Input/Output
Input/Output
4 GND
Input/Output GND
Input/Output
FP2500-T41 User Manual
1
Input/Output
1
3
Output
+5VIN
Input/Output USBInput/Output USB+
4
Input/Output GND
4
2
2
3
2-9
Specifications
2-5
Names and Functions of FP Parts
Front View
A: TFT Color LCD
The display monitor for your host.
B: Touch Panel
Allows you to perform touch operation.
H
C: Power Input Terminal Block
Provides the input and ground terminals for
a power cable.
D: Setting Switch (Dip switch)
A,B
E: VGA Interface (analog RGB) Connector
F: Serial Interface Connector
Used for both sending touch panel data to
the host, and receiving commands from the
host.
Rear View
G: USB Interface Connector
Used for both sending touch panel data to
the host, and receiving commands from the
host.
H: Front LED
C
D
EF G
An LED to detect power supply, backlight
burning out and input of image signal.
3-3-2 Front LED Operation Mode Display
2-10
FP2600-T41 User Manual
Specifications
2-6 Flat Panel (FP) Dimensions
2-6-1 External Dimensions ( DC24V )
Unit: mm [in.]
301.0 [11.85]
Top
317 [12.48]
58 [2.28]
243 [9.57]
227.0 [8.94]
8 [0.31]
Front
FP2600-T41 User Manual
Side
2-11
Specifications
2-6-2 Installation Brackets
Unit: mm [in.]
11[0.43]
16[0.63]
31[1.22]
10[0.39]
19.5[0.77]
2-6-3 FP Installation Dimensions
Unit: mm [in.]
FP
2-12
R
2
227.5 +10
[8.96 +0.04
]
0
Panel
de
n
301.5 +10 [11.87 +0.04
]
0
u
r4
FP2600-T41 User Manual
C h a p t e12345678901234567890123456789012
r 3
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
1. Installation
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
2. Wiring
Installation and Wiring
3. Operation Mode Setup and Display Positioning
3-1 Installation
Install the FP unit using the following steps.
Confirm the Installation Gasket's Positioning
It is strongly recommended that you use the gasket. It absorbs vibration in addition to
repelling water.
Place the FP on a level surface with the display panel facing downward.
Check that the FP's installation gasket is seated securely into the gasket's groove, which
runs around the perimeter of the panel's frame.
A gasket which has been used for a long period of time may have scratches
or dirt on it, and could have lost much of its dust and drip resistance. Be sure
to change the gasket periodically (or when scratches or dirt become visible).
Rear
View
Gasket
Create a Panel Cut
Following the FP Installation dimensions, create (cut) the FP opening required for installation. The FP's rubber gasket, installation brackets and screws are all required when
installing the FP.
Chapter 2-6-3 "FP Installation Dimensions".
Panel
Panel Cut
• It is important that the panel surface is flat, clean, and has no jagged
edges.
• The Panel thickness should be between 1.6mm and 10.0mm.
1.6 to 10mm
FP2600-T41 User Manual
3-1
Installation and Wiring
• For easier maintenance and operation, and improved ventilation, be sure
the FP unit is mounted at least 100 mm away from any adjacent structures
or objects.
• The FP uses natural ventilation through its outer shell for cooling. When
installing the unit horizontally or sideways (portrait style), use a fan or air
conditioning unit to prevent overheating.
Vertical Installation
Side
Front
Horizontal Installation
Sideways Installation
•
When installing the FP sideways, place it so that the Power Terminals point upwards.
•
Check that heat from surrounding equipment will not cause the FP to overheat.
•
Do not use the FP2600-T41 in an environment that exceeds 50o C.
•
Ensure this unit is located as far away as possible from electromagnetic circuits,
non-fuse type breakers, and other equipment that can cause arcing.
•
When installing the FP unit in a panel with an angled face, the face should not
incline either backwards or forwards more than 30o.
less than 30o
3-2
FP2600-T41 User Manual
Installation and Wiring
„ Installing the FP
Panel
1) Insert the FP into the panel cut
out, as shown here.
FP
Insertion Slots
2) Insert the installation fasteners
into the FP’s insertion slots, at
the top and bottom of the unit.
(total: 4 slots)
Top
Insertion Slots
Bottom
3) Insert each of the fasteners
shown below. Be sure to pull
the fastener back until it is flush
with the rear of the attachment
hole.
FP2600-T41 User Manual
3-3
Installation and Wiring
4) Use a Phillips screw driver to
tighten each fastener screw and
secure the FP in place.
Do not use too much force, since it may damage the FP unit. A torque of only 0.5 N•m is
sufficient to tighten these screws.
3-4
FP2600-T41 User Manual
Installation and Wiring
3-2 Wiring
3-2-1 Power Cable Connection
Warning
• To prevent electrical shocks, be sure the Power Cable is plugged first into
the FP unit, then into the wall (main supply).
• Your FP2600-T41 -24V uses input voltage of only DC24V. If your power
supply
is greater than that required by your unit, it may damage both the
power source
and the FP unit.
• In lieu of the power switch on the FP unit, please connect a breaker unit.
•
•
•
When connecting the FG terminal, be sure to connect the ground wire.
Not grounding the FP unit will create excessive noise and vibration.
Wherever possible, use thick wires (max. 2mm2) for power terminals,
and provide an extra twist to the wire before connecting it.
The ring terminal size should be as follows.
3.2 mm
less than 6.0 mm
• To avoid a power short when loosening power terminal screws, use a power
terminal with plastic sleeves.
FP2600-T41
(Rear)
24V Unit
FP2600-T41
+
+ -
-
FG
FG *1
Power Terminal Block
Crimp-on Ring
Terminals
*1 The three power terminals are:
DC24V + = Positive
DC24V = Negative electrode
FG
= Grounding Terminal connected to the FP chassis
FP2600-T41 User Manual
3-5
Installation and Wiring
Connect the FP power cable as follows:
1) Check to make sure the FP's power cord is disconnected.
2) Remove the plastic terminal cover.
3) Remove the screws from the 3 middle terminals, align the power wire connectors
and re-insert the screws. (Check each wire to make sure it is securely connected)
Use no more than 0.5 to 0.6N•m of torque to tighten the screws.
4) Replace the plastic terminal cover.
3-2-2
Connecting the Power Supply
M a i n FP
Power power
FP unit
input/output unit
M a i n FP
Power power
FP unit
Input/ Output Power
power
input/output
Input/ Output Power
main circuit
Operation
Motor
Unit
• When supplying power to the FP
unit, please separate the input/output
and operation unit lines, as shown.
• To increase the noise resistance
quality of the power cable, simply
twist each power wire before
attaching the Ring Terminal.
• The power supply cable must not be
bundled or positioned close to main
circuit lines (high voltage, high
current), or input/output signal lines.
• Connect a lightning surge absorber,
as shown in the diagram, to deal with
power surges.
• To avoid excess noise, make the
power cable as short as possible.
• Be sure to ground the surge
absorber (E1) separately
from the GP unit (E2).
FP unit
lightening
surge
absorber
3-6
• Select a surge absorber that
has a maximum circuit voltage greater than that of the
peak voltage of the power
supply.
FP2600-T41 User Manual
Installation and Wiring
3-2-3 Precautions: Grounding
(a) Exclusive grounding (BEST)
FP unit
other
equipment
Connect the FP's FG terminal to an exclusive ground. [diagram (a) - Grounding
resistance of under 100Ω.]
If exclusive grounding is not possible, use
a common connection point. [diagram
(b)]
(b) Common grounding (OK)
FP unit
other
equipment
(c) Common grounding (BAD)
FP unit
other
equipment
The grounding wire should have a cross
sectional area greater than 2mm2. Make
the connection point as close to the FP
unit as possible, and make the wire as
short as possible. When using a long
grounding wire, replace the thin wire with
a thicker wire placed in a duct.
If this equipment does not function properly when grounded, disconnect the
ground wire from the FG terminal.
3-2-4 Precautions: Input/Output Signal Lines
Input and output signal lines must be separated from operating circuit power cables.
If this is not possible, use a shielded cable and connect the shield to the FP chassis.
FP2600-T41 User Manual
3-7
Installation and Wiring
3-3 Operation Mode Setup and Display Positioning
3-3-1 Operation Mode Setup and Adjustment
The setup switches (dip-switches) are located in the rear of the unit.
FP2600-T41 (rear view)
Dip-switch
The default settings for the FP were created based on the standard connection method
used with IBM-PCs.
SW1
SW1-8 Selects touch panel transmission system, USB or SIO
SW1-7 Selects valid/invalid of factory set mode
SW1-6 Turns touch panel input's click sound ON/OFF
SW1-5 Selects Backlight Automatic OFF mode
Not used (Always OFF)
3-8
FP2600-T41 User Manual
Installation and Wiring
SW1-5
This switch controls the Automatic Backlight OFF mode.
When this switch is ON, and if there is no SIO transmission or touch operation
performed for 5 minutes, the backlight turns off automatically. It will remain OFF until
another SIO transmission or touch operation takes place, at which time the backlight
automatically turns back on.
If the FP unit is frequently not used, please set this switch ON to extend the life of the
backlight. Also, if a display related command is transmitted by the SIO, this Automatic
Backlight OFF mode will be automatically disabled.
FP does not have Power Save Mode.
SW1-6
This controls is used as the touch screen Click sound's ON/OFF switch.
When this is set to ON, a click will sound every time the touch panel is touched.
SW1-7
This is a switch to shift as adjustment mode at factory.
Please set this switch OFF when the FP unit is used.
SW1-8
This is a switch to change the data input (command control) of the touch panel.
Data output and command input/output will be performed from the USB connector
when this is ON and from the RS232C connector when it is OFF.
3-3-2 Front LED Operation Mode Display
L ED
Co n d itio n
P a ne l
L ig h t O F F
G re e n
Pow er O F F
Pow er O N
N orm al
Yes
Ba cklig h t
Im a g e in p u t
FP2600-T41 User Manual
O ra n g e
lig h tin g
Pow er O N
N orm al
No
G re e n /Re d
b lin kin g
Pow er O N
Bulb burned out
Yes
O ra n g e
b lin kin g
Pow er O N
Bulb burned out
No
3-9
Installation and Wiring
3-3-3 Display Position Compensation by OSD
The OSD (On Screen Display) is the screen menu displayed on the central part of the
screen when the following FP startup is performed.
1) OSD Startup Method
1)
2)
Touch the screen within 5 seconds in
order of 1) , 2) and 3).
Display
3)
2) Main Menu
The left illustrations are the main menu of OSD.
P
CL
3-10
D
By touching the characters on the display
screen, you can switch to that screen
adjustment mode.
Touching the ESC key will exit OSD mode.
ESC
FP2600-T41 User Manual
Installation and Wiring
3) Characters and their functions
Contrast adjustment :
The function to adjust Contrast
Sub-contrast adjustment :
The function to adjust contrast of each RGB color.
Brightness adjustment :
The function to adjust brightness of colors.
Horizontal display position adjustment :
The function to adjust horizontal position of the display screen.
Vertical display position adjustment :
The function to adjust the vertical position of the display screen.
Horizontal size adjustment :
The function to adjust the horizontal size of the screen.
P
D
CL
Phase adjustment :
The function to compensate the flicker.
Dimmer function :
The function to compensate the flicker of backlight.
Setup value clear :
Returns all setup values to default values.
ESC
Closes the OSD.
SET
Saves the setup values.
FP2600-T41 User Manual
3-11
Installation and Wiring
4) Menu Settings
<Example> Contrast Adjustment
Ajustment item
Adjustment bar
Adjustment key
SET
ESC
Save setup values
Cancel
The value for each setting item can be increased or decreased by pushing the adjustment
key.
• Contrast, Sub Contrast :
Higher contrast can be obtained by the value +.
• Brightness :
A hue can be brightened by the value +.
• Horizontal Display Position Adjustment :
Display moves right by pressing the value +.
• Vertical Display Position Adjustment :
Display moves up by pressing the value +.
• Horizontal Size Adjustment :
Screen size can be enlarged horizontally by the value +.
• Phase Adjustment :
CLK phase can be slowed by the value +.
• Dimmer Adjustment :
Backlight can be brightened by the value +.
Push the SET key to save value. Pushing the ESC key will return you to the main menu.
Clearing the Setup Value
ALLCLEAR
START
ESC
3-12
Push the character CL and it will shift to this
screen. When you push START, all setup data
of the adjustment items will be returned to
default value (factory set up value). By pushing
the ESC key, you will return to the main menu.
FP2600-T41 User Manual
Chapter 4
12345678901234567890123456789012
12345678901234567890123456789012
Touch 12345678901234567890123456789012
Panel Commands
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
1. Command
List
3. Touch Interface Data
12345678901234567890123456789012
12345678901234567890123456789012
2. Boot-up
Initialization
4. Touch Panel Commands
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
4-1
Command List
Here, the touch panel commands ( host -> touch panel ) supported by the FP2600T41 are described. The comma (,) used between the transferred format sent by the
touch panel to the host computer is only for separating commands, and has nothing to
do with the actual touch panel commands.
Command codes and data are all expressed in hexadecimal format.
(Example: 65h = 65 HEX)
<Touch Panel Commands>
Regardless of the dip-switch settings, the FP's display, click sound and buzzer
can all be controlled from the host computer by sending one-character touch
panel commands to the FP unit. The dip-switch settings are only enabled when
the FP is turned ON.
Code
65h / 67h
66h / 68h
69h
6Ah
6Bh
6Ch
71h
72h
73h
74h
FP2600-T41 User Manual
Function
Display ON
Display OFF
Click sound (high) ON
Click sound (high) OFF
Click sound (low) ON
Click sound (low) OFF
Buzzer (high) ON
Buzzer (high) OFF
Buzzer (low) ON
Buzzer (low) OFF
4-1
Touch Panel Commands
4-2
Boot-up Initialization
When the power is turned ON, the touch panel is initialized as follows.
Clears its internal buffer.
Initializes the serial communication mode.
Baud rate
9600bps
Data length
8 bits
Parity
none
Stop bit
1 bit
Initializes the system default values.
4-2
Function
Default Setting
Display output
ON
Backlight
ON
Click sound
ON or OFF selected with Dip SW1-6 (high)
Buzzer
OFF
Automatic OFF mode
ON or OFF selected with Dip SW1-5
FP2600-T41 User Manual
Touch Panel Commands
4-3 Touch Interface Data
Since the FP uses an analog type touch panel, all 800 x 600 coordinates can be
detected. Resolution of the analog touch panel is 1024 x 1024, so a conversion
program to convert the coordinates to 800 x 600 becomes necessary.
Also, a calibration program to adjust the actual touch position is needed.
As a result, the following software is included with the FP2600-T41 unit.
OS and Touch Panel Driver Combinations
OS
Windows (R) NT
Touch I/F Program
PL-TD000
Windows (R) 95
PL-TD000
Windows (R) 98
PL-TD000
Windows (R) 2000
PL-TD000
Others
user programmed
Calibration
Feature included in
the touch I/F program
Feature included in
the touch I/F program
Feature included in
the touch I/F program
Feature included in
the touch I/F program
user programme
Touch Panel Coordinate Data
(1) Resolution
Both the X and Y coordinates have a resolution of 1024.
The origin point (0,0) is located in the upper left corner of the screen.
(0,0)
Screen display origin, with resolution
of 800 x 600, is normally at the upper
left corner of the screen. Therefore, a
software to convert the touch coordinates to display coordinates is needed.
(1023,1023)
FP2600-T41 User Manual
4-3
Touch Panel Commands
(2) Data Format
All data is in binary format.
Header:
X coordinate:
Y coordinate:
1 byte (11h= touched; 10h = released)
2 bytes (0 to 3FFh)
2 bytes (0 to 3FFh)
X coordinate
Y coordinate
10h
11h
Added when touch is released.
<Example>
If the coordinate (X=23(11h), Y=500(1F4h)) is touched.
11h 0h 17h 1h F4h
11h 0h 17h 1h F4h
11h 0h 17h 1h F4h
11h 0h 17h 1h F4h
touched
continuous output with the same location
moving the location without releasing touch
continuous data output unless finger
is released
11h 0h 17h 1h F4h
11h 0h 17h 1h F4h 10h
when released, only 1 unit of data is sent
(3) Sampling Rate
A maximum of 87 points per second.
4-4
FP2600-T41 User Manual
Touch Panel Commands
4-4
Touch Panel Commands
The following are touch panel commands sent from the host computer to the FP
unit.
The letter inside the bracket next to the command code shows
the actual character used for that code.
Display ON
65h ( e ) / 67h ( g )
RS232C
65h ( e ) / 67h ( g )
USB
Turns on FP2600-T41's display. Backlight is also turned on simultaneously.
Display OFF
66h ( f ) / 68h ( h )
RS232C
Display OFF
66h ( f ) / 68h ( h )
USB
Turns off FP2600-T41's display. Backlight is also turned off simultaneously.
•
When the display is turned off by using this command, it is
necessary to write the Display ON command to turn it on again.
•
Unlike when making the display turn off by automatic backlight
OFF mode, the display will not reappear by touching the panel.
Further, the Automatic Backlight OFF mode is set up by the Dip
Swtch 1-5 and the mode will be decided by the Dip Switch
setup condition when the power source of the FP unit is turned
on.
Click sound (high) ON
69h ( i )
RS232C
69h ( i )
USB
Makes a high click sound when the touch panel is touched.
Click sound (high) OFF
6Ah ( j )
RS232C
6Ah ( j )
USB
The high click sound is disabled.
Click sound (low) ON
6Bh ( k )
RS232C
6Bh ( k )
USB
Makes a low click sound when the touch panel is touched.
Click sound (low) OFF
6Ch ( l )
RS232C
6Ch ( l )
USB
The low click sound is disabled.
FP2600-T41 User Manual
4-5
Touch Panel Commands
Buzzer (high) ON
71h ( q )
RS232C
Buzzer (high) ON
71h ( q )
USB
Turns on the buzzer output (high).
Buzzer (high) OFF
72h ( r )
RS232C
Buzzer (high) OFF
72h ( r )
USB
Turns off the buzzer output (high).
Buzzer (low) ON
73h ( s )
RS232C
73h ( s )
USB
Turns on the buzzer output (low).
Buzzer (low) OFF 74h ( t )
RS232C
74h ( t )
USB
Turns off the buzzer output (low).
The order of priority for the buzzer and click sounds is as follows. They are not
processed simultaneously.
Sound
Command Code
Buzzer (high) ON
71h
Buzzer (low) ON
73h
Click sound (high) ON
69h
Click sound (low) ON
6Bh
Priority Order
high
low
Also, if the OFF command for each buzzer item is sent, regardless of the priority
order, only that buzzer item is turned off.
<Example>
If the following three commands are sent at the same time...
Buzzer (high) ON
Buzzer (low) ON
Click sound (high) ON
... the Buzzer (high) activates. However, when the Buzzer (high) OFF
command is sent afterwards, the Buzzer (low) will activate.
4-6
FP2600-T41 User Manual
Touch Panel Commands
Reserved
The following commands are reserved. If these commands are used, they are
sometimes treated as errors.
00h
01h
02h
05h
0Ah
0Bh
0Dh
0Eh
0Fh
14h
15h
16h
17h
18h
19h
1Bh
1Dh
20h
21h
22h
23h
25h
26h
27h
28h
29h
2Ah
2Bh
31h
33h
3Ah
3Ch
41h
42h
43h
44h
45h
46h
47h
55h
FP2600-T41 User Manual
Reserved
4-7
Touch Panel Commands
MEMO
4-8
FP2600-T41 User Manual
Chapter12345678901234567890123456789012
5
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
Troubleshooting
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
Troubleshooting
1.
5-1 Troubleshooting
5-1-1 Possible Device Problems
Possible types of trouble while using this unit are as follows.
No display
- No display appears after the unit is switched on.
- The screen disappears during running mode.
- The screen does not display normally.
Touch panel doesn't function
The touch panel does not react when pressed, or its reaction time is abnormally
long.
Warning
- Because of the danger of electric shocks, be sure the power cable is not
connected when wiring the unit.
- When changing the backlight, there is a danger of electric shocks or burns, so
be sure to turn the unit OFF and wear gloves.
This section assumes that the FP is the cause of a problem, not the host.
When the host is the problem, please refer to its corresponding manual.
FP2600-T41 User Manual
5-1
Troubleshooting
5-1-2 No Display
When the screen does not display when powering up, or if the screen turns OFF
by itself, use the flowchart below to find an appropriate solution.
No Screen Display
YES
Does the backlight
(CFL) light up?
NO
Is it using the correct
power voltage?
NO
Connect the appropriate voltage.
Chapter 2. Specifications.
NO
Fix the power cable connection.
Chapter 3. Installation and Wiring.
YES
Turn OFF the power switch.
Is the power supply
cable connected properly
to the unit?
YES
Has the 11V unit's
backlight (CFL) been set
up correctly?
Check the 24V unit's backlight (CFL).
NO Change the backlight if it has burnt out.
Chapter 7-3 Replacing
the Backlight.
YES
There is a problem with the FP
unit. Please contact your local
FP distributor.
5-2
FP2600-T41 User Manual
Troubleshooting
Is the computer operating?
NO
Start the computer.
YES
Is RGB cable connected
NO
correctly?
Connect the RGB cable correctly.
Chapter 2-4 Cable
Diagrams.
YES
Is display mode
NO
right?
Select the correct display mode
with Dip SW1-4.
Chapter 3-3 Operation Mode
Setup and Display Positioning.
YES
Does the screen display
correctly?
YES
Adjust the screen display position.
Chapter 3-3 Operation
Mode Setup and Display Positioning.
NO
There is a problem with the FP
unit. Please contact your local
FP distributor.
FP2600-T41 User Manual
5-3
Troubleshooting
5-1-3 The Touch Panel Does Not Work
When the touch panel does not react, or its reaction is very slow after it is pressed,
follow the flowchart below to find the origin of the problem and the appropriate solution.
Touch panel not working
Is the SIO or USB cable
connected correctly?
NO
Connect the SIO or USB cable
correctly.
2-4 Cable Diagrams
YES
There is a problem with the FP
unit. Please contact your local
FP distributor.
5-4
FP2600-T41 User Manual
Chapter 12345678901234567890123456789012
6
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
1. Regular
Cleaning
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
2. Periodic
Check Points
12345678901234567890123456789012
12345678901234567890123456789012
Maintenance
3. Changing the Backlight
6-1
6-1-1
Regular Cleaning
Cleaning the Display
When the surface or the frame of the display gets dirty, soak a soft cloth in water
with a neutral detergent, wring the cloth tightly, and wipe the display.
• Do not use paint thinner, organic solvents, or a strong acid compound to clean the
unit.
• Do not use hard or pointed objects to operate the touch-screen panel, since it can
damage the panel surface.
6-1-2
Installation Gasket Check/Replacement
The installation gasket protects the FP and improves its water resistance. For
instructions on installing the FP's gasket, refer to
Chapter 3 "Installation and wiring"
A gasket which has been used for a long period of time may have
scratches or dirt on it, and could have lost much of its water resistance. Be sure to change the gasket at least once a year, or when
scratches or dirt become visible.
Installation Gasket Attachment Procedure (all units)
1) Place the FP on a flat, level
surface facing the display face
downwards.
2) Remove the gasket from the
FP.
FP2600-T41 User Manual
6-1
Maintenance
3) Attach the new gasket to the FP. Be
sure to insert the gasket into the GP’s
groove so that the gasket’s groove
sides are vertical.
4) Check if the gasket is attached to the
FP correctly.
• The gasket must be inserted correctly into the groove for the
FP’s moisture resistance to be equivalent to IP65f.
• The upper surface of the gasket should protrude approximately
2mm out from the groove. Be sure to check that the gasket is
correctly inserted before installing the FP into a panel.
Unit: mm [in.]
2.0 [0.08]
6-2
Periodic Check Points
To keep your FP unit in its best condition, please inspect the following points periodically.
FP Operation Environment
• Is the operating temperature within the allowable range (0oC to 50oC )?
• Is the operating humidity within the specified range (30%RH to 85%RH, dry
bulb temperature of 39oC or less)?
• Is the operating atmosphere free of corrosive gasses?
Electrical Specifications
• Is the input voltage appropriate (DC19.2V to DC28.8V)?
Related Items
• Are all power cords and cables connected properly? Have any become loose?
• Are all mounting brackets holding the unit securely?
• Are there many scratches or traces of dirt on the installation gasket?
6-2
FP2600-T41 User Manual
Maintenance
6-3
Replacing the Backlight
When the unit’s backlight burns out, the unit’s status LED will brink green/red or
orange.
FP2600-T41 units use a CFL, long-life type backlight. The actual life of the backlight however, will vary depending on the FP’s operating conditions, and replacement
may be required. A FP2600-T41 backlight has a life of 50,000 hours (approx. 5.7
years, at 25oC and 24 hour operation), when the backlight is lit continuously (time
required for brightness to fall to half its normal level.)
Warning
• To prevent an electric shock, be sure the FP’s power cord is un
plugged from the power outlet prior to replacing the backlight.
• When the power has just been turned OFF, the unit and backlight
are still very hot. Be sure to use gloves to prevent burns.
• The backlight is very fragile. Do not touch the glass tube directly
or try to remove its power cord. If the glass tube breaks you may
be injured.
Use the following table to check that you have ordered the correct backlight.
FP Model
FP2500-T41
FP2600-T41
Backlight Model
GP577R-BL00-MS
PS600-BU00
For backlight replacement details, refer to the replacement backlight unit’s
installation guide.
FP2600-T41 User Manual
6-3
Maintenance
MEMO
6-4
FP2600-T41 User Manual
Index
A
Afterimage iv
Analog RGB
interface viii, 2-4, 2-8, 2-10
Analog RGB Interface Cable 1-1, 1-2, 2-8
Angled face 3-2
Automatic OFF Mode 3-8, 3-9, 4-5
B
Backlight 1-2, 2-3, 6-3
Boot-up Initialization 4-2
Brightness 2-3
Brightness adjustment 3-11, 3-12
Buzzer 4-1, 4-6
C
Cable Diagrams 2-8
CAN/CSA-C22.2, Nos 142, and 213-M1987 x
CE Marking x
Cleaning the Display 6-1
Click sound 3-8, 3-9, 4-1, 4-6
Command List 4-1
Common grounding 3-7
Connecting the FP to a PC 1-1
Contrast adjustment 3-11, 3-12
Cover sheet 1-2
Clearing the Setup Value 3-12
D
Data Format
binaly format 4-4
Dimmer function 3-11, 3-12
Dip switch 2-10, 3-8
Disassembling iii
Display Area 2-3
Display colors 2-3
Display Media 2-3
Display mode vii, 2-3
Display Position Compensation by OSD 3-10
Dot Pitch 2-3
FP2600-T41 User Manual
E
Electrical Specifications 2-1, 6-2
Environmental Specifications 2-1
Exclusive grounding 3-7
External Dimensions 2-2, 2-11
F
Factory Set Mode 3-8, 3-9
FG terminal 3-5, 3-7
Flammable gas (environment) iii
Flat Panel (FP) Dimensions 2-11
FP Installation
Dimensions 2-12
FP Operation Environment 6-2
FP Parts
Names and functions 2-10
Front LED 2-10, 3-9
Functional Specifications 2-3
G
General Specifications 2-1
Grounding 3-7
Ground Connection 2-1
Guidelines iii
H
Header
Data Format 4-4
High voltage iii
Horizontal Installation 3-2
Horizontal size adjustment 3-11, 3-12
Horizontal display position adjustment 3-11, 3-12
I
IA (Industrial Automation) viii
Input Voltage 2-1, 3-5
Insertion Slot 3-3
Installation 3-1
Installation Gasket ix, 3-1, 6-1
Installation Guide ix
Installation brackets ix, 1-2, 2-12, 3-3
Interface Specifications 2-4
Internal buffer 4-2
IP65F 2-1
i
L
R
Liquid Crystal Display (LCD) iv
Rubber gasket 1-2, 3-1
M
S
Maintenance 6-1
Maintenance parts 1-2
Metallic dust iii
Mouse Emulator 1-2
Safety Instructions iii, iv
Sampling Rate 4-4
Serial Interface 2-6, 2-10
Setup value clear 3-11, 3-12
Sideways Installation 3-2
Signal Names 2-5, 2-6, 2-7
SIO Interface Cable 1-1, 1-2, 2-9
Specifications
Electrical 2-1
Environmental 2-1
Interface 2-4
Structural 2-2
Storage Temperature 2-1
Structural Specifications 2-2
Sub-contrast adjustment 3-11, 3-12
Surge absorber 3-7
Symbols ii
N
Natural ventilation iv, 3-2
Noise Endurance 2-1
No Screen Display
Troubleshooting 5-2
O
OA (Office Automation) viii
Operating Temperature 2-1
Operation Mode Setup 3-8
Optional Equipment 1-2
Overheat 3-2
OSD 2-4, 3-10
P
Packaging
Contents ix
Phase adjustment 3-11, 3-12
Pin Assignments 2-5, 2-6, 2-7
PL-TD000 1-2, 4-3
Possible Device Problems 5-1
Power Cable Connection 3-5
Power Input Terminal Block 2-10, 3-5
Power Terminals 3-5
Precautions: Grounding 3-7
Precautions: Input/Output Signal Lines 3-7
Precautions: Power Supply 3-6
Priority
Buzzer and Click sounds 4-6
ii
T
TFT Color LCD viii, 2-10
Touch Interface Data 4-3
Touch Panel 2-3, 2-10
Touch Panel Command 4-1, 4-5
Touch Panel Coordinate Data 4-3
Touch Panel Does Not Work
Troubleshooting 5-4
Touch Panel Driver 4-3
Troubleshooting 5-1
U
UL/c-UL x
UL1604 x
UL508 x
UL Registration Model x
User Manual ix
USB Interface 2-7, 2-10
USB Interface Cable 1-1, 1-2, 2-9
FP2600-T41 User Manual
V
Vertical Installation 3-2
Vertical display adjustment 3-11, 3-12
Vibration Endurance 2-1
Voltage Transformer 3-6
W
Weight 2-2
Wiring 3-5
Grounding 3-7
Input/Output Signal Lines 3-7
Power Cable 3-5
Power Supply 3-6
When Connecting to a PC vii
FP2600-T41 User Manual
iii
MEMO
iv
FP2600-T41 User Manual