Craftsman 315.114630 Operator`s manual

Operator's Manual
318 in., 15.6 VOLT CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model No.
315.114630
Save this manual
future reference
for
• Safety
• Features
--A_WARNING: Toreduce
the risk of
injury, the user must read and
understand the operator's manual before
using this product.
Customer
Help Line: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman
Visit the Craftsman web page: www.sears.com/craftsman
983000-318
7-03
• Operation
• Maintenance
• Parts List
Estates,
IL 60179
USA
•
Warranty .........................................................................................................................................................................
2
•
Introduction .....................................................................................................................................................................
2
•
General Safety Rules .................................................................................................................................................
•
Specific Safety Rules .....................................................................................................................................................
4
•
Important Safety Rules for the Charger .........................................................................................................................
5
•
Symbols ..........................................................................................................................................................................
6
•
Product Specifications ....................................................................................................................................................
7
•
Features .....................................................................................................................................................................
•
Operation ..................................................................................................................................................................
•
Maintenance .................................................................................................................................................................
15
•
Exploded View And Repair Parts List ..........................................................................................................................
17
•
Parts Ordering / Service ...............................................................................................................................................
18
FULL ONE YEAR WARRANTY
ON CRAFTSMAN
3/8 in. CORDLESS
3-4
7-8
9-14
DRILL-DRIVER
If this CRI_FTSMRN3/8 in. Cordless Drill-Driver fails to give complete satisfaction within one year from the date of purchase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES,
and Sears will replace it, free of charge.
If this rRnFTSMRM 3/8 in. Cordless Drill-Driver is used for commercial or rental purposes, this warranty applies for only
99 days from the date of purchase.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179
Your drill-driver has many features for making your drilling
operations more pleasant and enjoyable. Safety,
performance and dependability have been given top
priority in the design of this drill-driver making it easy to
maintain and operate.
,_
WARNING: Do not attempt to use the tool until you
have thoroughly read and completely understand the
operator's manual. Pay close attention to the safety
rules, including Dangers, Warnings, and Cautions. If
you use this tool properly and only for what it is
intended, you wilt enjoy years of safe, reliable
service.
Look for this symbol to point out important safety precautions.
safety is involved.
It means attention!H
Your
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power toot operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields, available at Sears
Retail Stores. Always wear eye protection which is marked to comply with ANSI Z87.1.
2
_1_ WARNING:
Read and understand all instructions. Failure to fellow all instructions listed below,
may result in electric shock, fire and/or serious
personal injury.
SAVE THESE
WORK
AREA
•
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
A battery operated tool with integral batteries or a
separate battery pack must be recharged only with
the specified charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery.
•
Use battery
designated
may create
Use battery
•
•
•
operated tool only with specifically
battery pack. Use of any other batteries
a risk of fire.
only with charger listed.
MODEL
315.114630
•
•
SAFETY
•
BATTERY PACK
Item No. 9 11465
130234027
•
CHARGER
Item No. 9 11466
140250013
•
•
SAFETY
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious
personal injury.
•
•
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
•
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting
the battery pack into a tool with the switch on invites
accidents.
•
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your
application. The correct toot will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off. A
toot that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect battery pack from tool or place the
switch in the locked or off position before making
any adjustments, changing accessories, or storing
the tool. Such preventive safety measures reduce the
risk of starting the toot accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
Do not abuse the cord. Never use the cord to carry
the charger. Keep cord away from heat, oil, sharp
edges, or moving parts. Replace damaged cords
immediately. Damaged cords may create a fire.
PERSONAL
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
•
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL
•
•
TOOL USE AND CARE
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
•
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations.
INSTRUCTIONS
•
•
•
•
3
When
other
nails,
make
battery pack is not in use, keep it away from
metal objects like: paper clips, coins, keys,
screws, or other small metal objects that can
a connection from one terminal to another.
Shorting the battery terminals together may cause
sparks, burns, or a fire.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may
be suitable for one tool may create a risk of injury when
used on another tool.
Keep the tool and its handle dry, clean and free
from oil and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleumbased products, or any strong solvents to clean your
tool. Following this rule will reduce the risk of loss of
control and deterioration of the enclosure plastic.
SERVICE
•
•
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
ment parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
by unqualified personnel could result in a risk of injury,
•
When servicing a tool, use only identical replace-
Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden
wiring. Contact with a "live" wire will also make exposed metal parts of the tool "live" and shock the operator.
ADDITIONAL
RULES
FOR SAFE OPERATION
•
Know your power tool. Read operator's manual carefully. Learn its applications and limitations, as well as
the specific potential hazards related to this tool.
Following this rule wilt reduce the risk of electric shock,
fire, or serious injury.
•
Always wear safety glasses with side shields. Everyday glasses have only impact resistant lenses. They are
NOT safety glasses. Following this rule will reduce the risk
of eye injury.
IMPORTANT
RULES
FOR BATTERY
TOOLS
•
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not
using your battery tool or when changing accessories. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
Do not place battery tools or their batteries near fire or
heat. This will reduce the risk of explosion and possibly
injury.
4
•
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light. To
reduce the risk of serious personal injury, never use any
cordless product in the presence of open flame. An
exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
•
Do not charge battery tool in a damp or wet location.
Following this rule wilt reduce the risk of electric shock.
•
For best results, your battery tool should be charged in
a location where the temperature is more than 50°F but
less than 100°F. Do not store outside or in vehicles.
•
Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with
your skin, wash immediately with soap and water,
then neutralize with lemon juice or vinegar. If liquid
gets into your eyes, flush them with clean water for at
least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk of serious
personal injury.
c. That wire size is large enough for AC ampere
rating of charger as specified below:
_ILWARNING:
Read
and understand all instructions.
Failure to follow all instructions listed below, may
result in electric shock, fire and/or serious personal
injury.
•
Never use a battery that has been dropped or
received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped battery
immediately. Failure to heed this warning can result in
serious personal injury.
•
Save these instructions. This manual contains important safety and operating instructions for charger.
•
Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and product using battery charger. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
Do not expose charger to wet or damp conditions.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
•
Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons. Following
this rule will reduce the risk of electric shock, fire, or
serious personal injury.
•
To reduce risk of damage to charger body and cord,
pull by charger plug rather than cord when disconnecting charger. Following this rule will reduce the risk
of electric shock, fire, or serious personal injury.
•
Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress. Following this rule will reduce the risk of serious
personal injury.
•
Do not abuse cord. Never carry tool by cord or yank
it to disconnect from receptacle. Keep cord from
heat, oil and sharp edges. Following this rule will reduce
the risk of electric shock or fire.
•
An extension cord should not be used unless absolutely necessary. Use of improper extension cord could
result in a risk of fire and electric shock. If extension cord
must be used, make sure:
25'
50'
100'
Cord Size (AWG)
16
16
16
Note: AWG = American Wire Gage
CAUTION: To reduce risk of injury, charge only nickelcadmium type rechargeable batteries. Other types of
batteries may burst causing personal injury and damage. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
Cord Length (Feet)
•
Do not operate charger with a damaged cord or plug.
If damaged, have replaced immediately by a qualified
serviceman. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
•
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way; take
it to a qualified serviceman. Following this rule wilt
reduce the risk of electric shock, fire, or serious personal
injury.
•
Do not disassemble
charger; take it to a qualified
serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock
or fire. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
To reduce the risk of electric shock, unplug charger
from outlet before attempting
any maintenance or
cleaning. Turning off controls will not reduce this risk.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
•
Disconnect charger from power supply when not in
use. Following this rule will reduce the risk of electric
shock, fire, or serious personal injury.
•
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions also. Following this rule will reduce the risk of
electric shock, fire, or serious personal injury.
,i_
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and
cement and other masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.
a. That pins on plug of extension cord are the
same number, size and shape as those of plug
on charger.
b. That extension cord is properly wired and in good
electrical condition; and
SAVE THESE INSTRUCTIONS
5
Important:Someofthefollowingsymbolsmaybeusedonyourtool.Pleasestudythemandlearntheirmeaning.Proper
interpretation
of thesesymbolswillallowyoutooperatethetoolbetterandsafer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
min
Minutes
Time
Alternating Current
Type or a characteristic
of current
-'='=
Direct Current
Type or a characteristic
of current
no
No Load Speed
Rotational speed, at no load
.../min
Revolutions or Reciprocation Per Minute
Revolutions, strokes,
surface speed, orbits etc. per minute
Safety Alert Symbol
It
means attention!!!
Your orcaution.
safety is
indicates
danger, warning
involved.
Wear Eye Protection
safety
with side
shields
Alwaysglasses
wear safety
goggles
or when
operating this product.
Wet Conditions Alert
Do not expose to rain or use in damp
locations.
,_
O
L
7
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves
eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention
measures.
Symbol
Meaning
DANGER:
Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
,_
WARNING:
serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or
,_
CAUTION:
Indicates
potentially
situation
which,
if not avoided,
result
in minordamage.
or
moderate injury.
It maya also
be usedhazardous
to alert against
unsafe
practices
that maymay
cause
property
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
g
6
24 Positions
Chuck..........................................................
3/8in. Keyless Clutch.............................................................
Motor..............................................................
15.6VoltDC ChargerInput.................................
120V, 60Hz,AConly
3-6Hours
Switch.......................................................
VariableSpeed ChargeRate.......................................................
Torque.................................................................
110in.lb.
GearTrain.............................................................
1 Speed
NoLoadSpeed.................................................
0-600/min.
KNOWYOUR DRILL-DRIVER
FORWARD/REVERSE
See Figure 1.
(DIRECTION
Before attempting to use your drill-driver, familiarize
yourself with all operating features and safety
requirements.
Your drill-driver has a forward/reverse
KEYLESS
SELECTOR
OF ROTATION SELECTOR)
selector located
above the switch trigger.
WRIST
CHUCK
STRAP
Your drill-driver has a keyless chuck that allows you to hand
tighten or release drill bit in the chuck jaws.
A wrist strap is provided to reduce the chances of dropping
your drill-driver. Place one hand through the wrist strap
when carrying tool.
SWITCH
BIT STORAGE
To turn your drill-driver ON, depress the switch trigger.
Release switch trigger to turn your drill-driver OFF.
When not in use, bit(s) provided with your drill-driver can
be placed in the storage area located on the bottom of the
motor housing.
SWITCH
LOCK
LEVEL
The switch trigger can be locked in the OFF position. This
feature helps reduce the possibility of accidental starting
when not in use.
VARIABLE
To keep drill bit level during drilling operations, a level is
located on the back of the motor housing.
SPEED
,_
This toot has a variable speed switch that delivers higher
speed with increased trigger pressure. Speed is controlled
by the amount of switch trigger depression.
7
WARNING: If any parts are missing, do not operate
your drill-driver until the missing parts are replaced.
Failure to do so could result in possible serious
personal injury.
LEVEL
TORQUE
ADJUSTMENT
RING
KEYLESS
CHUCK
REARVIEW
DIRECTIONOF
ROTATIONSELECTOR
(FORWARD/REVERSE)
BIT
STORAGE
SWITCH
TRIGGER
SCREWDRIVER
BITS
BATTERYPACKSHOWN
IN CHARGINGSTAND
CHARGER
BATTERYPACK
SHOWNINTOOL
WRISTSTRAP
RED LIGHT
(LED)
CHARGERSTAND
Fig. I
8
,_
light indicates the charger is operating properly. It will
remain on until battery pack is removed from charging
stand or charger is disconnected from power supply.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
•
Note: If charger does not charge battery pack, return
battery pack and charging assembly to your nearest
Sears Repair Center for electrical check.
•
The battery pack for your toot has been shipped in a low
charge condition to prevent possible problems. Therefore,
you should charge it overnight prior to use.
After normal usage, a 3 hours or less of charging time
is required to fully recharge battery pack. Note: If
battery pack is completely discharged, 6 hours or
longer of charging time is required to fully recharge
battery pack.
•
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.
The battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
•
Do not place charger in an area of extreme heat or
cold. It wilt work best at normal room temperature.
CHARGING
•
When batteries become fully charged, unplug charger
from power supply and remove the battery pack.
_
WARNING:
Do not allow familiarity with your drilldriver to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
BATTERY
PACK
BATTERY
PACK
See Figure I.
•
Charge battery pack only with the charging assembly
provided.
IMPORTANT
INFORMATION
HOT BATTERIES
•
Make sure power supply is normal household
voltage, 120 volts, 60 Hz, AC only.
•
Connect charger to power supply.
•
Place battery pack in charging stand. Align raised rib
on battery pack with groove in charging stand.
See Figure I.
When using your
your battery pack
battery pack coot
before attempting
•
Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charging
stand.
•
The charge indicator light (LED), located on the
charging stand, wilt light up red and glow when the
charger is properly connected to power supply. This
FOR RECHARGING
drill-driver continuously, the batteries in
wilt become hot. You should let a hot
down for approximately 30 minutes
to recharge.
Note: This situation only occurs when continuous use of
your drill causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING
BATTERY PACK" for normal recharging of batteries. If
the charging assembly does not charge your battery pack
under normal circumstances, return both the battery pack
and charging assembly to your nearest Sears repair
center for electrical check.
9
SWITCH
TO INSTALL
See Figure 2.
•
To turn your drill ON, depress the switch trigger. To turn it
OFF, release the switch trigger.
Lock switch trigger on your drill by placing the direction
of rotation selector in center position. See Figure 4.
•
Place battery pack in your drill. Align raised rib on
battery pack with groove inside drill. See Figure 3.
SWITCH
TRIGGER
VARIABLE
Fig. 2
BATTERY
PACK
BATTERYPACK
SPEED
This tool has a variable speed switch that delivers higher
speed and torque with increased trigger pressure. Speed is
controlled by the amount of switch trigger depression.
LATCHES
Note: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned, this is a normal
part of the switch function.
_DEPRESSLATCHESTO
RELEASEBATTERYPACK
•
_k
Make sure the latches on each side of your battery
pack snap in place and battery pack is secured in drill
before beginning operation.
CAUTION:
When placing battery pack in your drill,
be sure raised rib on battery pack aligns with groove
inside drill and latches snap into place properly.
improper assembly of battery pack can cause
damage to internal components.
TO REMOVE
10
Fig. 3
BATTERY
PACK
•
Lock switch trigger on your drill by placing the direction
of rotation selector in center position. See Figure 4.
•
Locate latches on side of battery pack and depress to
release battery pack from your drill. See Figure 3.
•
Remove battery pack from your drill.
SWITCH
LOCK
KEYLESS
CHUCK
See Figure 4.
See Figure 5.
The switch trigger can be locked in the OFF position. This
feature can be used to prevent the possibility of accidental
starting when not in use. To lock switch trigger, place the
direction of rotation selector (Forward/Reverse Selector)
in center position.
Your drill has a keyless chuck. As the name implies, you can
hand tighten or release drill bits in the chuck jaws. Grasp and
hold the collar of the chuck with one hand. Rotate the chuck
SELECTORWITH
CENTERLOCKPOSITION
body with your other hand. The arrows on the chuck
indicate which direction to rotate the chuck body in order to
LOCK (tighten) or UNLOCK (release) the drill bit.
REVERSE
UNLOCK
(RELEASE)
CHUCK
COLLAR
DRILLBIT
SWITCH
FORWARD TRIGGER Fig. 4
_IL
CHUCKJAWS
LOCK
(TIGHTEN)
WARNING:
Battery tools are always in operating
condition. Therefore, switch should always be locked
when not in use or carrying at your side.
Fig. 5
REVERSIBLE
_
See Figure 4.
This toot has the feature of being reversible. The direction
of rotation is controlled by a selector located above the
switch trigger. With the drill held in normal operating
position, the direction of rotation selector should be
positioned to the left of the switch for drilling. The drilling
direction is reversed when the selector is to the right of
the switch. When the selector is in center position, the
switch trigger is locked.
,_
CHUCK
BODY
CAUTION: To prevent gear damage, always allow
chuck to come to a complete stop before changing
the direction of rotation.
To stop, release switch trigger and allow the chuck to come
to a complete stop.
11
WARNING:
Do not hold chuck body with one hand
and use power of the drill to tighten chuck jaws on
drill bit. Chuck body could slip in your hand or your
hand could slip and come in contact with rotating drill
bit. This could cause an accident resulting in serious
personal injury.
INSTALLINGBITS
REMOVING
See Figure 6.
See Figure 6.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 4.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 4.
•
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use.
Also, raise the front of your drill slightly to keep the bit
from falling out of the chuck jaws.
•
Loosen the chuck jaws from drill bit.
•
To loosen: grasp and hold the collar of the chuck with
one hand, while rotating chuck body with your other
hand. Note: Rotate chuck body in the direction of the
arrow marked UNLOCK to loosen chuck jaws.
•
Do not use a wrench to tighten or loosen the chuck
jaws.
•
Remove drill bit from chuck jaws.
•
Insert drill bit straight into chuck the full length of the
jaws as shown in Figure 6.
•
Tighten the chuck jaws on drill bit.
UNLOCK
(RELEASE)
CHUCK
COLLAR
ADJUSTABLE
DRILLBIT
CHUCKJAWS
LOCK
(TIGHTEN)
RIGHT
•
,_
TORQUE
CLUTCH
Your drill is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
The proper setting depends on the type of material and the
size of screw you are using.
TO ADJUST
•
BITS
•
Identify the twenty four torque indicator settings located
on the front of your drill. See Figure 8.
•
Rotate adjusting ring to the desired setting.
• 1-4
5-8
CHUCK
BODY
• 9 - 12
Note: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten chuck jaws.
Do not use a wrench to tighten or loosen the chuck
jaws.
For driving small screws.
For driving screws into soft
material.
• 13 - 16
For driving screws into soft and hard
materials.
For driving screws in hard wood.
• 17 - 20
For driving large screws.
• 21 - ,11
For heavy drilling.
Fig. 6
To tighten the chuck jaws on drill bit; grasp and hold
the collar of the chuck with one hand, while rotating
the chuck body with your other hand.
TORQUE
TO DECREASE
TORQUE
ADJUSTING
RING
WARNING:
Make sure to insert drill bit straight into
chuck jaws. Do not insert drill bit into chuck jaws at
an angle then tighten, as shown in Figure 7. This
could cause drill bit to be thrown from drill, resulting
in possible serious personal injury or damage to the
chuck.
TO INCREASE
TORQUE
Fig. 7
12
Fig. 8
BIT STORAGE
DRILLING
See Figure 9.
See Figure11.
When not in use, bits provided with your drill can be
placed in the storage area located on the bottom of your
drill as shown in Figure 9.
SCREWDRIVER
BITS
BIT
STORAGEAREA
Fig. 9
d_k WARNING: Always wear safety goggles or safety
glasses with side shields when operating tools.
Failure to do so could result in objects being thrown
into your eyes, resulting in possible serious injury.
Fig. 11
When drilling hard smooth surfaces use a center punch to
mark desired hole location. This wilt prevent the drill bit
from slipping off center as the hole is started. However,
the low speed feature allows starting holes without center
punching if desired. To accomplish this, simply operate
your drill at a low speed until the hole is started.
The material to be drilled should be secured in a vise or
LEVEL
See Figure 10.
A convenient feature provided with your drill is a level. It
is recessed in the motor housing on back of your drill. It
can be used to keep drill bit level during drilling operations.
with clamps to keep it from turning as the drill bit rotates.
REARVIEWOF DRILL
Hold tool firmly and place the bit at the point to be drilled.
Depress the switch trigger to start toot.
LEVEL
Move the drill bit into the workpiece applying only enough
pressure to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
,_
WARNING:
Be prepared for binding or bit
breakthrough. When these situations occur, drill has
a tendency to grab and kick opposite to the direction
of rotation and could cause loss of control when
breaking through material. If not prepared, this loss
of control can result in possible serious injury.
When drilling metals, use a light oil on the drill bit to keep
it from overheating. The oil wilt prolong the life of the bit
and increase the drilling action.
Fig. 10
If the bit jams in workpiece or if the drill stalls, release
switch trigger immediately. Remove the bit from the
workpiece and determine the reason for jamming.
13
CHUCK
REMOVAL
•
See Figures 12, 13, and 14.
The chuck must be removed in order to use some
accessories. To remove:
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 4.
•
Insert a 5/16 in. or larger hex key into the chuck of your
drill and tighten the chuck jaws securely.
Insert hex key in chuck and tighten chuck jaws securely. Tap sharply with a mallet in a counterclockwise
direction. This will loosen chuck on the spindle. It can
now be unscrewed by hand. See Figure 14.
MALLET
• Tap the hex key sharply with a mallet in a clockwise
direction. See Figure 12. This wilt loosen the screw in
the chuck for easy removal.
MALLET
CHUCKJAWS
Fig. 14
TO RETIGHTEN
A LOOSE
CHUCK
The chuck may become loose on spindle and develop a
wobble. Periodically check chuck screw for tightness.
KEYLESS
CHUCK
To tighten, follow these steps:
Fig. 12
• Open chuck jaws and remove hex key. Remove the
chuck screw by turning it in a clockwise direction. See
Figure 13.
•
Lock the switch trigger by placing the direction of
rotation selector in center position. See Figure 4.
•
Open the chuck jaws.
•
Insert hex key into chuck and tighten chuck jaws
securely. Tap hex key sharply with a mallet in a
clockwise direction. This wilt tighten chuck on the
spindle.
•
Open the chuck jaws and remove hex key.
•
Tighten the chuck screw.
Note: The screw has left hand threads.
Note: The chuck screw has left hand threads.
SCREWDRIVER
Fig. 13
14
,1_
Do not abuse power tools. Abusive practices can
damage toot as well as workpiece.
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other part
may create a hazard or cause product damage.
Only the parts shown on parts list, page 17, are intended
to be repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not attempt to modify this toot or
create accessories not recommended for use with
this tool. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating oils,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken or destroy
plastic.
BATTERIES
To preserve natural resources, please
recycle or dispose of batteries properly.
Your drill's battery pack is equipped with nickel-cadmium
rechargeable batteries. Length of service from each
charging wilt depend on the type of work you are doing.
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of nickel-cadmium
batteries in ordinary trash.
The batteries in this toot have been designed to provide
maximum trouble free life. However, like all batteries, they
will eventually wear out. Do not disassemble battery pack
and attempt to replace the batteries. Handling of these
batteries, especially when wearing rings and jewelry,
could result in a serious burn.
Consult _our local waste authority for information
regarding available recycling and/or disposal options.
BATTERY PACK REMOVAL
FOR RECYCLING
To obtain the longest possible battery life, we suggest the
following:
•
Store and charge your batteries in a cool area.
Temperatures above or below normal room
temperature will shorten battery life.
•
Never store batteries in a discharged condition.
Recharge them immediately after they are
discharged.
•
All batteries gradually lose their charge. The higher
the temperature the quicker they lose their charge. If
you store your tool for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery life.
AND PREPARATION
WARNING:
Upon removal, cover the battery pack's
terminals with heavy duty adhesive tape. Do not
attempt to destroy or disassemble battery pack or
remove any of its components. Nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with these
warnings could result in fire and/or serious injury.
15
i
i
r
M
i
r
r
i
16
CRAFTSMAN
318 in., 15.6 VOLT CORDLESS
MODEL NO. 315.114630
DRILL-DRIVER
--
The model number will be found on a plate attached to the motor housing. Always mention the model number
__ in all correspondence
regarding your 3/8 in. CORDLESS
SEE BACK
PAGE FOR PARTS
DRILL-DRIVER
ORDERING
or when orde_
INSTRUCTIONS
2
1
4
3
PARTS LIST
Key
No.
Part
Number
Description
1
660120002
Screw (Special) .................................................................
1
2
690033002
Chuck (Item No. 9 20988) .................................................
1
Quan.
3
* Item No. 9 11465
Battery Pack (130234027)
................................................
1
4
* Item No. 9 11466
Charging Assembly (140250013) .....................................
1
300636086
Carrying Case - Not Shown .............................................
1
983000-318
Operator's Manual
5
* Can Be Purchased Thru RSOS (Retail Special Order System)
17
Get it fixed, at your home or ours!
Your Home
For repair-in
your home-of
all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime,
day or night (U.S.A. only)
www.sears.com
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced
1-800-827-6655
(U.S.A.)
1-800-361-6665
Para pedir servic=o de reparacion
a domicdio, y para ordenar piezas:
1-888-SU-HOGAR
_, Marca
rT
• _ Marque
Reg_strada
/
IH
de commerce
(Canada
Au Canada pour service
en fram;a=s:
1-800-LE-FOYER
SM
Mc
(1-800-533-6937)
www.sears
ca
(1-888-784-6427)
_, Registered Trademark /
by Sears:
"_Trademark / _F
"'_Serv=ce Mark of Sears Roebuck and Co
TF
Marca
ID
/_
de Fabnca
Marque
! _TI Marca de Servlclo
deposee
de Sears
Roebuck
de Sears,
and Co
Roebuck
and Co
_, Sears,
Roebuck
and Co