OWNER’S
MANUAL
The following parts are included with your Baracuda G3 (Model# W03000):
(1) FlowKeeper™ Valve
(1) Pool Pulse™
(1) Cleaner Head
(1) Hose Weight
(1) Finned Disc
(12) Hose Lengths
(1) Universal
Valve Cuff
(1) 41/2" Connector
(2) 45 Degree Elbows
(1) Hose Protector Net
W83409
THANK YOU FOR PURCHASING BARACUDA® G3™.
YOUR BARACUDA G3 HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY
INSTALLED AND TO PROVIDE YEARS OF LOW MAINTENANCE OPERATION.
PRIOR TO INSTALLING YOUR NEW BARACUDA G3, PLEASE DO THE FOLLOWING:
1) Complete and return the warranty card.
2) Record your purchase information on the spaces provided below.
3) Attach your invoice (or a copy) to this page.
These actions will insure prompt warranty service, should it be required. Simply present your owner’s manual, along with the invoice at any of our
authorized warranty centers nationwide.
RECORD YOUR BARACUDA G3 POOL CLEANER DATA HERE:
Date of Purchase ___________ Purchased From ________________________________________ Serial Number: ______________________________
(located on underside of machine head)
City __________________________________________________ State_______________________________ Zip Code _________________________
BARACUDA G3 LIMITED WARRANTY
This BARACUDA G3 was carefully inspected before shipment from our warehouse. Upon unpacking, if any part proves defective or missing, please notify Zodiac
Pool Care, Inc. immediately. Please consult owner’s manual for complete instructions on the installation and operation of your BARACUDA G3.
ZODIAC POOL CARE, INC. WARRANTS THE BARACUDA G3 POOL CLEANER AGAINST ALL MANUFACTURING DEFECTS AND ALL WEAR AND
TEAR FOR (2) YEARS. ALL WARRANTIES ARE EFFECTIVE FROM THE DATE OF PURCHASE.
Should this product prove defective in workmanship, materials or wear during the applicable warranty period, the consumer’s sole and exclusive remedy shall be
such repair or replacement of the product as provided below.
THE LIMITED WARRANTY PROVIDED HEREIN IS THE SOLE AND EXCLUSIVE WRITTEN WARRANTY WITH RESPECT TO THE
BARACUDA G3 POOL CLEANER. ALL IMPLIED WARRANTIES IMPOSED BY APPLICABLE LAW, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THE EXPRESS LIMITED
WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
THIS LIMITED WARRANTY EXCLUDES THE FOLLOWING:
1. Discoloration of the BARACUDA G3 pool cleaner. This is caused by reaction to ultraviolet rays and the chemicals used in the pool water. Discoloration does not
affect the operating ability of the BARACUDA G3. Therefore, this Limited Warranty does not cover the replacement of discolored parts.
2. Damage to or malfunction of the unit resulting from excess chlorination or improper water chemistry balance.
3. Replacement of parts which fail or become defective as a result of improper installation, negligence, misuse, abuse or tampering by unauthorized repair personnel.
4. Age, pool water imbalance, and improper installation can cause vinyl pool liners to become brittle or unduly wrinkled. Corrosion of the supporting walls and/or
irregularities in the pool base may also cause liner failure. The use of this product in such an environment is at the pool owner’s risk. Therefore, the pool owner
hereby releases the manufacturer from any and all claims for damage where these conditions exist.
5. The BARACUDA G3 is designed for use in inground pools only. If unit is used in any other application, the pool owner hereby releases the manufacturer from any
and all claims. This misuse will void all warranty on the unit.
6. In no event shall Zodiac Pool Care, Inc. be liable in contract or in tort, or under any other legal theory, for lost profits or revenues, loss of use or similar economic
loss, or for indirect, special, incidental, consequential or similar damages, even if it has been advised of the possibility of such claim. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
IMPORTANT WARRANTY NOTICES FOR VINYL LINER POOL OWNERS
• Certain vinyl liner patterns are particularly susceptible to rapid surface wear or pattern removal caused by objects coming into contact with the vinyl surface,
including pool brushes, pool toys, floats, fountains, chlorine dispensers, and automatic pool cleaners.
• Some vinyl liner patterns can be seriously scratched or abraded simply by rubbing the surface with a pool brush. Ink from the pattern can also rub off during the
installation process or when it comes into contact with objects in the pool. Zodiac is not responsible for, and the Limited Warranty does not cover, pattern
removal, abrasion or marking on vinyl liners.
• Vinyl liners are subject to deterioration or damage due to age, the effect of chemicals, corrosion or failure of the supporting walls; as well as improper installation,
maintenance or cleaning of the supporting walls or base.
• Before installing the Baracuda G3, examine the interior of your pool carefully. If your vinyl liner is brittle or has stones, wrinkles, roots or metal corrosion in contact
with the underside of the liner, or has damage to the base material or supporting walls, do not install the Baracuda G3 before having a qualified professional perform
the necessary repairs.
ZODIAC POOL CARE, INC. WILL NOT BE RESPONSIBLE FOR LINER DAMAGE CAUSED BY (1) A BARACUDA G3 CLEANER WHICH IS IN
DISREPAIR, (2) PATTERN REMOVAL FROM A VINYL LINER, OR (3) A BARACUDA G3 CLEANER USED IN A POOL HAVING AN AGED OR
DETERIORATED LINER.
WARRANTY PROCEDURES
No claim under this Limited Warranty will be recognized unless the registration card, included in your box, is completed and returned within fifteen (15) days of the
purchase date. Only the original purchaser may submit a claim under this Limited Warranty. Purchaser’s claims against Zodiac Pool Care, Inc., shall be limited
to those claims which may be asserted under the Limited Warranty relating to any defect, malfunction or wear of the BARACUDA G3.
To obtain warranty replacements or repair, call (888) 786-7797 for authorization. When submitting a claim, always supply serial number, evidence of purchase date,
retailer and a brief description of the problems/defects encountered. Zodiac Pool Care, Inc. reserves the right to repair or replace all defective or worn parts covered by
this Limited Warranty and return same to purchaser, freight collect.
Zodiac Pool Care, Inc. assumes no responsibility for any warranties or representations made by other individuals or businesses beyond the express terms contained
in this Limited Warranty.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For sale and use in the United States, Canada and Mexico only. This pool cleaner is not warranted or guaranteed outside of the United States, Canada or Mexico.
This pool cleaner is covered by one or more of the following Canadian and U.S. patents and Canadian registered design:
U.S. patent nos. 4642833, 4742593, 5421054 and 5450645. Canadian patent nos. 1254105 and 1256262. Other Patents Pending.
INGROUND AUTOMATIC POOL CLEANER
INSTALLATION GUIDE
Pool Preparation .......................................................................................................................... 2
Assembly ....................................................................................................................................... 3
Hose Assembly................................................................................................................................3
Balance ............................................................................................................................................4
Removing Air From Hose..............................................................................................................4
Installation ......................................................................................................................................5
Achieving Proper Flow ..................................................................................................................6
Adjustments....................................................................................................................................7
Troubleshooting..............................................................................................................................7
Accessories ......................................................................................................................................8
HOW YOUR ZODIAC AUTOMATIC POOL CLEANER WORKS
•
•
•
•
Your pool pump pulls water from the main drain and the skimmer through a strainer basket, then pushes the water through the
filter system and back into the pool through the return inlets.
The Zodiac Automatic Pool Cleaner connects to the skimmer or dedicated vacuum line with the hose sections provided. Water
flows through the diaphragm of the cleaner at a rate of 14 to 19 gallons per minute.
Diverting or re-directing the return inlets downward breaks up the circulation pattern of water within the pool. This allows
random cleaning around the pool.
Most common problems can be eliminated, by reading through the entire manual before installing your new Zodiac.
POOL COMPONENTS
FILTER
PUMP
PUMP
STRAINER
BASKET
RETURN INLET/SKIMMER
& MAIN DRAIN VALVES
DEDICATED
VAC LINE
RETURN
INLET
RETURN
INLET
SKIMMER
MAIN
DRAIN
•
•
Please become familiar with the components of your pool shown.
All diagrams are provided for reference of terminology used throughout this manual. Your pool may vary.
W83342
Thank you for purchasing this automatic pool cleaner from Zodiac. Prior to installing your pool cleaner,
review the parts and warranty information and insure that all parts shown are included with your unit.
Although the appearance of your model Zodiac Pool Cleaner may differ slightly from some
drawings shown in this installation guide, installation steps remain the same.
STEP 1 - POOL PREPARATION
•
•
•
•
•
Before installing the Zodiac Automatic Pool Cleaner, examine the interior of your pool carefully. If your vinyl liner is brittle or
has stones, wrinkles, roots or metal corrosion in contact with the underside of the liner, or has damage to the base material or
supporting walls, do not install the pool cleaner before having a qualified professional perform the necessary repairs.
Close the main drain. This allows the flow to be regulated by the Flowkeeper.
Manually vacuum the pool. This eliminates unnecessary adjustment later.
Clean the pool filter and empty the skimmer and pump strainer baskets. Filter pressure rises as debris is cleaned from the water,
thus reducing flow.
Divert the pool return inlets downward - (IMPORTANT!). Your Zodiac Automatic Pool Cleaner must move randomly throughout
the pool. Water circulating at the surface will influence the hose and limit coverage.
• To adjust the return inlet: loosen the lock ring and redirect the eyeball downward, then retighten the lock ring. If the eyeball is
difficult to adjust, insert a screwdriver inside the eyeball and gently adjust downward.
• If the return inlets cannot be pointed downward, then you MUST install Zodiac return line diverters. They are available through
your Zodiac dealer.
BEFORE ADJUSTMENT
TOP VIEW
SIDE VIEW
AFTER ADJUSTMENT
TOP VIEW
FOR POOLS WITH RETURN INLET
DIRECTIONAL FITTINGS
Replace the directional eyeball
with Zodiac retrofit eyeball return
line diverter and reinstall eyeball
retaining ring.
Part #W90153 for
11/2" return lines
Part #W90155 for
2" return lines
2
SIDE VIEW
IF UNABLE TO ADJUST RETURN INLETS
OR FOR POOLS WITHOUT RETURN INLET
DIRECTIONAL FITTINGS
Use Zodiac universal return
line diverter (Part #W24100).
Pinch wires together and
insert fully into return inlet.
STEP 2 - ASSEMBLY
FINNED DISC INSTALLATION
Slide the finned disc over the foot pad. Insure the disc fits properly in the grooves provided and rotates freely on the foot pad.
The fins on the disc face upward.
CE
FINS FA
D
UPWAR
BOTTOM VIEW
REAR VIEW
WHEEL DEFLECTOR INSTALLATION (Only used on some pool cleaners.)
Some Zodiac Pool Cleaner models require a wheel deflector for proper performance. If your model includes one, slide the wheel
deflector over the extension pipe and secure between the two lowest pipe ridges. Make sure the top clips of the wheel deflector are
seated in the groove. The wheel deflector should rotate freely.
GROOVE
GROOVE
STEP 3 - HOSE ASSEMBLY
FOR CORNER OR END INSTALLATIONS
If your skimmer or wall vacuum fitting is located at the corner
or end of your pool, use enough hose sections to reach the
farthest point in the pool, plus one (1) section.
SKIMMER / WALL
VACUUM FITTING
SKIMMER / WALL
VACUUM FITTING
FOR CENTER INSTALLATIONS
If your skimmer or wall vacuum fitting is located at the center of
your pool, use enough hose sections to reach the farthest point in
the pool, plus two (2) sections.
SKIMMER / WALL
VACUUM FITTING
SKIMMER / WALL
VACUUM FITTING
Note: You may not need to use all or you may need more hose sections,
with either installation method, depending upon your pool size.
3
STEP 4 - BALANCE
Zodiac Automatic Pool Cleaners require a specific number of hose weights to compensate for the buoyancy of the hose depending
on the cleaner model. A properly balanced pool cleaner hose will create a 45-degree angle from the cleaner head and the bottom of
the pool as shown below.
FOLLOW THE GUIDELINES BELOW FOR YOUR SPECIFIC CLEANER MODEL.
(Model number is stated on the cover of the manual.)
MODEL# W83251 - Hose weight is not required for this model cleaner in most pools. As a troubleshooting technique to
improve coverage or prevent the cleaner from climbing the walls excessively, snap (1) hose weight onto the first hose section,
one meter from the cleaner head.
MODEL# W03000 - Snap (1) hose weight onto the middle of the first hose section, 1/2 meter from the cleaner head.
MODEL# W83215 & W83216 - Snap (2) hose weights onto the middle of the second hose section,
1 1/2 meters from the cleaner head.
INCORRECT
CORRECT
INCORRECT
Note: For pools 8 1/2 feet or deeper, please refer to page 7 of this manual for balancing instructions.
STEP 5 - REMOVING AIR FROM HOSE
•
•
Turn the filtration system off.
Attach the cleaner head to the female end of the hose.
•
•
Turn on the filtration system.
Fill the hose with water by placing the end over a return inlet.
RETURN
INLET
4
STEP 6
INSTALLATION FOR POOLS WITH SKIMMERS
FLOWKEEPER VALVE
In skimmer installations the Flowkeeper Valve MUST BE used. The pool pump provides more gallon per
minute flow than your pool cleaner requires. The Flowkeeper provides a way to regulate the flow with a bypass
so the pool pump and the pool cleaner run properly.
Skimming action is maintained through a bypass throat in the valve. As the filter collects debris, the valve
automatically maintains the correct flow to the cleaner. The Flowkeeper Valve comes preset at the setting required
for your cleaner. There are a total of three setting options. The lower the setting number, the lower the flow to the
cleaner head. Should readjustment become necessary, pull the adjustment handle to raise or lower the setting. The
red tab on the valve can be used to keep the bypass open, which in most cases, will cause the cleaner to stop.
A
(1) Flowkeeper Valve
B
C
D
E
(1) Valve Cuff
(1) Hose Protector Net
(1) 41/2" Connector
(2) 45° Elbows
Example 2
Example 1
D
E
E
C
A
D
C
A
B
B
Arrow on Flowkeeper must be pointed downward, toward skimmer.
•
•
•
Using the parts shown, choose a fitting combination best suited for your skimmer. You may have parts left over.
Attach the hose protector net (C) to the hose section that goes into the skimmer.
Remove the skimmer basket, attach the Flowkeeper Valve combination to the hose with protector net, and install into the skimmer
as shown in example 1 or 2. Turn on the filtration system. Continue to STEP 7.
Note: For pools with multiple skimmers, connect the Flowkeeper Valve combination to the skimmer closest to the plumbing manifold.
INSTALLATION FOR POOLS WITH DEDICATED VAC LINE
NO FLOWKEEPER VALVE REQUIRED
•
Insert the male end of the hose into the large end of the
45˚ Elbow.
•
Insert the small end of the 45˚ elbow into vac lock and angle
the 45˚ elbow toward the pool surface. Continue to STEP 7.
Important: To help prevent
suction entrapment accidents,
wall vacuum fittings should
have a safety vac lock installed.
Contact your builder or retail
pool professional for details.
5
STEP 7 - ACHIEVING PROPER FLOW
IDEAL
TOO HIGH
TOO LOW
POOL PULSE®
The Pool Pulse is a flow meter that measures the volume of water flowing through your Zodiac cleaner. It must be used to properly set
the flow and can be used as a diagnostic tool when the cleaner isn't running properly.
For the following steps, using 2 people is recommended; one poolside and the other at the plumbing manifold. Vacuum and skimmer
valves are located at your plumbing manifold.
•
•
•
•
•
•
•
Remove the cleaner head.
Attach the Pool Pulse® to the end of the hose and keep it under water as shown in Figure 1.
Turn on the filtration system.
For pools with one skimmer, flow is automatically regulated by the Flowkeeper Valve. Insure the blue indicator of the Pool
Pulse is in the ideal range (when viewed from the side).
For pools with two or more skimmers, leave the selected skimmer open and slowly close the other skimmer(s) until the blue
indicator of the Pool Pulse moves into the ideal range (when viewed from the side).
For pools with a wall vacuum fitting, leave the wall vacuum fitting fully open and slowly close the skimmer valve until the blue
indicator of the Pool Pulse moves into the ideal range (when viewed from the side).
Keeping the hose under water, remove the Pool Pulse. Submerge the cleaner head, and when the bubbles stop coming from the
extension pipe, attach the hose end. Your installation is now complete.
SAMPLE PLUMBING
MANIFOLD
NOTE: Plumbing manifolds vary by
pool. Refer to your pool builder for
questions regarding your plumbing
manifold configuration.
Figure 1
If the flow is in the low range, review the installation procedures. A dirty pool filter, clogged baskets and improperly set valves are
usually the main cause of low flow. Other types of hydraulic problems may require a professional pool repairman.
If the flow is in the high range, review the installation procedures. Confirm that the valves controlling these lines are properly set.
Lower the setting on the Flowkeeper Valve. Slightly open the main drain as a last option if flow is still excessive.
6
ADJUSTMENTS
BALANCE - POOLS THAT ARE 8 1/2 FEET OR DEEPER
FOLLOW THE GUIDELINES BELOW FOR YOUR SPECIFIC CLEANER MODEL.
MODEL# W83251 - Snap (1) hose weight onto the first hose section, one meter from the cleaner head.
MODEL# W03000, W83215, and W83216 - An additional hose weight (#W83247) may be necessary to balance the Zodiac Pool
Cleaner head. If the cleaner is not balanced correctly in the deep end of the pool (as shown on page 4), turn off the pump and add an
additional hose weight approximately 5 to 8 feet away from the cleaner head. Place the pool cleaner in the deep end, turn on the
pump and determine whether the correct balance has been achieved. If not, re-position the additional hose weight accordingly.
Additional hose weights may be purchased from your Zodiac dealer if required.
IMPROVING COVERAGE
Normally it is undesirable for the return line water flow to affect the natural movement of the pool cleaner hose. However, the
following illustration shows how return line pressure can be used to balance cleaning coverage or to guide the cleaner away from step
areas with “V” shaped corners.
Technique
Position the return line
directional so that you can
only detect water movement
on the surface 8 feet out from
the wall, and aim it at the
center of the opposite wall.
A return line located anywhere
along the shaded area can be
utilized to gently push the hose
allowing the pool cleaner to free
itself from in-pool obstacles.
TROUBLESHOOTING
PROBLEM
Cleaner stops & starts
Cleaner is patterning
Cleaner isn't covering
opposite end of pool
Cleaner stuck at steps
Cleaner stuck under ladder
Cleaner flips over
Cleaner won't climb walls
Cleaner doesn't move
SOLUTION
Check diaphragm for blockage or damage. Use Pool Pulse® to determine proper flow.
Add return diverters or divert return inlets downward. Lay hose in a straight line in the sun to relax
memory. Confirm proper hose length - add 1 to 2 hose sections.
Add return diverters or divert return inlets downward. Use flow to move cleaner to opposite end.
Move hose weight away from cleaner head slightly. In deep pools add additional weight.
Utilize return flow (see adjustments). Confirm proper hose length. Adjust flow to cleaner. Adjust hose
weight. Install wheel deflector.
Install ladder guard (#W24000).
Contact tech services for local warranty station.
Cleaner may not climb walls of some vinyl pools. Use Pool Pulse and raise flow. Confirm proper hose
length. Adjust hose weight.
Use Pool Pulse to insure proper flow. Clean baskets & filter. Check diaphragm for damage. Check hose
sections for leaks by lifting each section above water.
Use Pool Pulse to lower flow. Utilize return flow to move cleaner. Adjust hose weight.
Cleaner won't leave edge
or rim of pool
Solar blanket installation
Coverage will be limited due to blanket.
NOTE: In cold water of 60˚ or less, water flow through the cleaner must be increased to compensate for the reduced
flexibility of the hose and diaphragm.
IF ASSISTANCE IS REQUIRED, PLEASE CALL US AT 1-888-786-7797
7
ZODIAC ACCESSORIES
PART ILLUSTRATION
PART NO.
DESCRIPTION
1. W24000
Ladder Guard
Always use on stainless steel
in-pool ladders
2. W24100
Return Line Diverter
Use when no other
return inlet directional
fittings exist.
3A. W90153
Retrofit Eyeball Return
Line Diverter
Use to replace standard
directional inlet eyeballs.
1
2
(for 11/2" return inlet)
3B
3A
3B. W90155
(for 2" return inlet)
4. W26705
The Leaf Catcher
with 4 1/2" Hose Connector
Use when heavy debris or
leaf situations exist.
5. W83247
Additional 37g Hose Weight
May be required to properly
balance the Zodiac cleaner head.
4
5
ZODIAC POOL CARE, INC.
2028 N.W. 25th Avenue
Pompano Beach, FL 33069
1-888-786-7797
www.zodiacpoolcare.com
BARACUDA G3™ CARE AND MAINTENANCE
To maintain quality, performance and increase the lifespan of your Baracuda G3, please do the following:
1. The skimmer basket, pump basket and pool filter should be thoroughly cleaned on a regular basis. Always disconnect the hose
from the skimmer before backwashing.
2. NEVER COIL THE HOSE when the cleaner is removed from the pool. A coiled hose can be straightened with hot water or by
laying it on a warm pool deck for several hours.
X
CORRECT
INCORRECT
3. REMOVE THE CLEANER BEFORE SUPER CHLORINATING OR ADDING POOL CHEMICALS. Reinstall the Baracuda G3
when the imbalance is corrected or after a minimum of 4 hours from super chlorination. Chemical damage is not covered under warranty.
4. Periodically inspect parts for wear. The footpad and disc are the most critical. When the depth of the channels between the treads
of the footpad are 1/8" or less, replace the footpad.
Quick Access Cassette System
Foreign objects, such as children’s toys, tree branches and rocks, should be removed manually from your pool prior to operating your
Baracuda® G3™. If a blockage should occur, the Quick Access Cassette System will allow you to check the diaphragm for damage and
remove the blockage in minutes at poolside.
DIAPHRAGM REMOVAL
Unscrew cassette (Step 1) and remove from head (Step 2). Loosen swivel pipe (Step 3). Pull out diaphragm & inner pipe (Step 4). Pull
diaphragm from inner pipe (Step 5) and inspect for blockage or cuts. Remove blockage and rinse. Do not use sharp objects as damage to
diaphragm may occur. If replacement parts are needed, contact technical service at 1-888-786-7797 for an authorized warranty station.
Step 1
Step 4
Step 3
Step 2
Step 5
DIAPHRAGM ASSEMBLY
Be sure the retaining ring is on the diaphragm, then push diaphragm onto inner pipe (Step 6). Insert inner pipe into diaphragm chamber and
seat diaphragm against lip (Step 7). Tighten cassette assembly (Step 8). Insert cassette into head (Step 9) and tighten handnut (Step 10).
Step 8
Step 7
Step 6
Step 9
Step 10
REPLACING THE FOOT PAD
Unthread and remove the cassette (Steps 1 & 2). Holding the Baracuda G3 as shown (Step 3), press down on the yellow clip while
pulling the foot flange toward you. Pull off the old footpad and stretch on the new one. Insert the locking clip of the foot flange into
the large opening (Step 4), push forward to lock into place (Step 5) insert the cassette and tighten (Step 6).
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
BARACUDA G3™ PARTS DIAGRAM
10
5
17
16
11
6
13
18
19
20
2
9
21
4
8
7
3
1
22
23
12
24
14
25
15
PART NO.
QTY.
1.
W69541
Left G3 Main Body
1
2.
W69542
Right G3 Main Body
1
3.
W56124
Float - Baracuda G3
1
4.
W41079
Weight - Baracuda G3
1
5.
W69545
Retaining Collar - Baracuda G3
1
6.
W69559
Cassette Chambers Upper and Lower
1
7.
W69698
Long Life Diaphragm
1
8.
W81600
Retaining Ring
1
1
9.
W56525
Inner Extension Pipe
10.
W69540
Cassette Outer Extension Pipe w/ Handnut 1
11.
W74000
Compression Ring
1
12.
W69732
Foot Flange
1
13.
W69526
Bumper Fin - Baracuda G3
1
14.
W72880
Foot Pad - Teal
1
15.
W46666
Finned Disc - Teal
1
16.
W60050
FlowKeeper Valve
1
17.
W33160
4 1/2" Connector - Aqua
1
18.
W44800
Pool Pulse®
1
19.
W90146
45º Elbow
1
20.
W63900
Inground Valve Cuff
1
21.
W33800
Hose Protector Net
1
22.
W83247
Hose Weight
1
23.
W83140
Long-Life Hose Kit - 12x1 Meter - Aqua
1
24.
W33411
Wheel Deflector (Optional Accessory)
1
25.
W41721
Wheel Adapter (Optional Accessory)
1
ZODIAC POOL CARE, INC.
2028 N.W. 25th Avenue
Pompano Beach, FL 33069
1-888-786-7797
www.zodiacpoolcare.com
DESCRIPTION