Barco R9827889 Installation manual

DATA
808s
R9002031
R9002038
INSTALLATION MANUAL
Downloaded From projector-manual.com Barco Manuals
BARCO PROJECTION SYSTEMS
DATA
808s
R9002031
R9002038
INSTALLATION MANUAL
Date :
170397
Downloaded From projector-manual.com Barco Manuals
Art. No. :
R5975607
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, March 1997.
All rights reserved.
Trademarks are the rights of their respective owners.
Printed in Belgium
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Printed in Belgium
Downloaded From projector-manual.com Barco Manuals
Table of contents
TABLE OF CONTENTS ................................................................................................................................ I-1
SAFETY INSTRUCTIONS
On safety .............................................................................................................................................
On installation ......................................................................................................................................
On servicing .........................................................................................................................................
On cleaning ..........................................................................................................................................
On repacking .......................................................................................................................................
On illumination .....................................................................................................................................
1-1
1-2
1-2
1-2
1-2
1-2
UNPACKING AND PROJECTOR DIMENSIONS
Unpacking ............................................................................................................................................ 2-1
Projector dimensions ........................................................................................................................... 2-2
INSTALLATION GUIDELINES
Environment ......................................................................................................................................... 3-1
What about ambient light ? .................................................................................................................. 3-1
Which screen type? ............................................................................................................................. 3-1
What image size? How big should the image be? .............................................................................. 3-1
Where to install the projector ? ............................................................................................................ 3-2
Mounting Configuration ........................................................................................................................ 3-2
INSTALLATION SET-UP
Access to Controls .............................................................................................................................. 4-1
Opening the top cover ................................................................................................................................................................. 4-1
Removing the top cover .............................................................................................................................................................. 4-1
Re-installing the top cover .......................................................................................................................................................... 4-1
Scan Adaptation .................................................................................................................................. 4-2
Getting access to the scan switches ........................................................................................................................................ 4-2
Horizontal scan switches ........................................................................................................................................................... 4-2
Vertical scan switch ................................................................................................................................................................... 4-2
PROJECTOR SET-UP
Setting the projector address ............................................................................................................... 5-1
Power-up mode .................................................................................................................................... 5-2
Operational mode ........................................................................................................................................................................ 5-2
Stand-By mode ............................................................................................................................................................................ 5-2
Baud Rate for communication with a computer .................................................................................... 5-3
Password mode ................................................................................................................................... 5-3
AC POWER CONNECTION
AC Power cord connection .................................................................................................................. 6-1
Preparing your power cord ................................................................................................................... 6-1
Mains lead with CEE7 plug .......................................................................................................................................................... 6-1
Power cord with an ANSI 73.11 plug ......................................................................................................................................... 6-1
AC Power check ..................................................................................................................................
AC Input power voltage adaptation .......................................................................................................
Switching on the projector ...................................................................................................................
Starting up with a full white image .......................................................................................................
6-2
6-2
6-3
6-3
Starting up with "warm up period" .............................................................................................................................................. 6-3
Starting up without "warm up period" ........................................................................................................................................ 6-3
SOURCE CONNECTIONS
Signal input connection ........................................................................................................................ 7-1
Connecting a Composite Video source to Port 1 ................................................................................. 7-1
Connecting a S-Video (or Composite Video) source to Port 2 ............................................................. 7-2
Connecting a RGB Analog source to Port 3 ........................................................................................ 7-2
Connecting a RGB Analog source to Port 4/5 ..................................................................................... 7-3
5975607 BARCODATA 808s 110397
Downloaded From projector-manual.com Barco Manuals
i-1
Table of contents
Connecting a Component Video source to Port 4/5 ............................................................................. 7-3
Connecting a RGB Analog source with Tri-level sync to Port 4/5 (option) ............................................ 7-4
Connecting a Component Video source with Tri-level sync to Port 4/5 (option) ................................... 7-4
Peripheral equipment ........................................................................................................................... 7-4
Connecting a RCVDS 05 source selector to the projector ........................................................................................................ 7-4
Connecting a VS05 source selector to the projector ................................................................................................................. 7-4
Connecting an IR Remote Receiver 800 to the projector ........................................................................................................... 7-4
INSTALLATION ADJUSTMENT MODE
Before startin any adjustment .............................................................................................................. 8-1
Access to Installation Adjustment Mode ............................................................................................. 8-3
Overview flowchart of the Installation Adjustment Mode ....................................................................... 8-3
Projector Distance ............................................................................................................................... 8-4
Optical Lens Focusing ......................................................................................................................... 8-4
Raster Centering .................................................................................................................................. 8-5
CRT Projection Angle Adjustment ....................................................................................................... 8-6
MESSAGES, WARNINGS AND FAILURE CODES
Appendix A : Barco ceiling mount support
Appendix B : G2 adjustment
Appendix C : Gamma corrections
i-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 110397
Safety instructions
1
SAFETY INSTRUCTIONS
Projectors are built in accordance with the requirements of the
international safety standards IEC950, UL 1950 and CSA C22.2 No.
950, which are the safety standards of information technology
equipment including electrical business equipment.
These safety standards impose important requirements on the use
of safety critical components, materials and isolation, in order to
protect the user or operator against the risk of electric shock and
energy hazard, and having access to live parts.
Safety standards also impose to the internal and external temperature variations, radiation levels, mechanical stability and strength,
enclosure construction and protection against risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
Installation instructions
Before operating your projector please read this manual thoroughly,
and retain it for future reference.
Installation and preliminary adjustments should be performed by
qualified BARCO personnel or authorized BARCO service dealers.
OWNER’S RECORD
The article number (Art. No.) and serial number (Ser. No) are located
at the rear of the projector. Copy these numbers in the spaces
provided below. Refer to them whenever you call upon your BARCO
dealer regarding this product.
Article number
:
Serial number
:
Dealer
:
Warning :
To prevent fire or electrical shock hazard,
do not expose this projector to rain or moisture
Federal Communication Commission (FCC statement)
This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Instructions to the user :
If this equipment does cause interference to radio or television
reception, the user may try to correct the interference by one or more
of the following measures :
* Re-orientate the receiving antenna for the radio or television.
* Relocate the equipment with respect to the receiver.
* Plug the equipment into a different outlet so that the equipment and
receiver are on different branch circuits.
* Fasten cable connectors to the equipment with mounting screws.
Note :
The use of shielded cables is required to comply within the limits
of Part 15 of FCC rules and EN55022.
General safety instructions :
* All the safety and operating instructions should be read before using
this unit.
* The operating instruction manual should be retained for future
reference.
* All warnings on the projector and in the documentation manuals
should be adhered to.
* All instructions for operating and use of this equipment must be
followed precisely.
On safety
* This product should be operated from an AC power source.
* This projector may be connected to an IT power system.
* Operating AC power voltage of the projector when leaving the
factory:
BARCODATA 808s
Art. No.: R9002031 (230 VAC)
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts inside
Art. No.: R9002038 (120 VAC)
Consult the appropriate section of this manual to switch over from
230 Vac to 120 Vac or from 120 Vac to 230 Vac.
If you are not sure of the type of AC power available, consult your
dealer or local power company.
this product risk electrical shock to persons.
The exclamation point within a triangle is intended
to tell the user that important operating and/or
servicing instructions are included in the technical
documentation for this equipment.
5975607 BARCODATA 808s 110397
Downloaded From projector-manual.com Barco Manuals
* This product is equipped with a 3-wire grounding plug, a plug having
a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete
1-1
Safety instructions
outlet. Do not defeat the purpose of the grounding-type plug.
WARNING FOR THE USERS:
THIS EQUIPMENT MUST BE GROUNDED (EARTHED) via the supplied
3 conductor AC power cable. (If the supplied power cable is not the
correct one, consult your dealer.)
A. Mains lead (AC Power cord) with CEE 7 plug
The colors of the mains lead are colored
in accordance with the following code:
Yellow + Green : Earth (Ground)
Blue
: Neutral
Brown
: Line (Live)
B. Power cord with ANSI 73.11 plug
The wires of the power cord are colored in
accordance with the following code.
Yellow + Green : Earth (Ground)
White
: Neutral
ρ
ρ
Black
: Line (live)
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord. To disconnect the cord,
pull it out by the plug. Never pull the cord itself.
If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the
extension cord does not exceed the extension cord ampere rating.
Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes.
ρ
Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
Never spill liquid of any kind on the product. Should any liquid or solid
object fall into the cabinet, unplug the set and have it checked by
qualified service personnel before resuming operations.
ρ
Lightning - For extra protection for this video product during a
lightning storm, or when it is left unattended and unused for a long
period of time, unplug it from the wall outlet. This will prevent damage
to the projector due to lightning and AC power-line surges.
On installation
* Do not place this projector on an unstable cart, stand, or table. The
projector may fall, causing serious damage to it.
* Do not use this projector near water.
* Use only the power cord supplied with your projector. While
appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the projector.
For a replacement power cord, contact your dealer.
* Slots and openings in the cabinet and the sides are provided for
ventilation; to ensure reliable operation of the projector and to
protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product
should never be placed near or over a radiator or heat register. This
projector should not be placed in a built-in installation or enclosure
1-2
Downloaded From projector-manual.com Barco Manuals
unless proper ventilation is provided.
On servicing
Do not attempt to service this projector yourself, as opening or
removing covers may expose you to dangerous voltage potential and
risk of electric shock! Refer all projector service to a qualified
BARCO service center.
Call for service in the following conditions :
* When the power cord or plug is damaged or frayed.
* If liquid has been spilled into the projector.
* If the product has been exposed to rain or water.
* If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of
the other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to
normal operation.
* If the product has been dropped or the cabinet has been damaged.
* If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be
sure the service technician has used original BARCO replacement
parts or authorized replacement parts which have the same characteristics as the BARCO original part. Unauthorized substitutions
may result in degraded performance and reliability, fire, electric shock
or other hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the projector is in proper operating condition.
On cleaning
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning.
To keep the cabinet looking brand-new, periodically clean it with a soft
cloth. Stubborn stains may be removed with a cloth lightly dampened
with mild detergent solution. Never use strong solvents, such as
thinner or benzine, or abrasive cleaners, since these will damage the
cabinet.
To ensure the highest optical performance and resolution, the
projection lenses are specially treated with an anti-reflective coating,
therefore : avoid touching the lens. To remove dust on the lens, use
a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.
On repacking
Keep the original shipping carton and packing material; they will come
in handy if you ever have to ship your projector. For maximum
protection, repack your set as it was originally packed at the factory.
On illumination
In order to obtain the best quality for the projected image, it is essential
that the ambient light which is allowed to fall on the screen be kept
to an absolute minimum.
When installing the projector and screen, care must be taken to avoid
exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting
fixtures.
The use of controlled ambient lighting, such as incandescent spot light
or a dimmer, is recommended for proper room illumination. Where
possible, care should also be taken to ensure that the floors and walls
of the room in which the projector is to be installed are non-reflecting,
dark surfaces. Brighter surfaces will tend to reflect and diffuse the
ambient light and hence reduce the contrast of the projected image
on the screen.
5975607 BARCODATA 808s 110397
Unpacking and dimensions
2
UNPACKING AND PROJECTOR DIMENSIONS
Unpacking
To open the banding around the carton, pull out the clip as shown
below :
Take the projector out of its shipping carton and place it on a table.
Save the original shipping carton and packing material, which will
come in handy if you ever have to ship your projector. For maximum
protection, repack your projector as it was originally packed at the
factory.
Contents of the shipping carton :
ρ
1 BARCODATA 808s projector
ρ
1 Remote Control Unit plus 1 battery 9V
ρ
1 power cord with outlet plug type CEE7 or ANSI 73.11
ρ
1 Owner's Manual
ρ
1 Installation Manual
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 110397
2-1
Unpacking and dimensions
Projector dimensions (in mm)
APPROXIMATE WEIGHT WITH HD8 LENS - 67 KG
CRT POINT
CRT
R7626572
R7626575
R7626576
R7627612
R7627615
R7627616
A
B
806
209
1040
A
816
596
211
590
CRT POINT
GRAVITY POINT
ROTATION COVER
169.5
B
170
27
84
226
286
362
*SERVICE*
45.5
456
136
558
728
576
MAX 500
960
FRONT IR RECEIVER
AIRFLOW
148
POWER SUPPLY
FIXATION POINT
*4 X M8*
703
BACK IR RECEIVER
MAX 428
AIRFLOW
AIRFLOW
510
590
MAX 1076
AIRFLOW
Downloaded From projector-manual.com Barco Manuals
2-2
5975607 BARCODATA 808s 110397
Installation guidelines
3
INSTALLATION GUIDELINES
Installation guidelines
Careful consideration of things such as image size, ambient light
level, projector placement and type of screen to use are critical
to optimize the use of the projection system.
Environment
Which screen type?
Do not install the projection system in a site near heat sources such
as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the
ceiling; Make sure the temperature near the installation site is not
excessive.
There are two major categories of screens used for projection
equipment. Those used for front projected images and those for rear
projection applications.
Screens are rated by how much light they reflect (or transmit in case
of rear projection systems) given a determined amount of light
projected toward them. The ‘GAIN’ of a screen is the term used. Front
and rear screens are both rated in terms of gain. The gain of screens
range from a white matte screen with a gain of 1 (x1) to a brushed
aluminized screen with a gain of 10 (x10) or more. Another important
consideration is the degree the screen's gain varies with the horizontal and vertical viewing angle. The choice between higher and lower
gain screens is largely a matter of personal preference.
In considering the type of screen to choose, determine where the
viewers will be located and go for the highest gain screen possible.
A high gain screen will provide a brighter picture but reduce the
viewing angle.
For more information about screens, contact your local screen
supplier.
What about ambient light ?
The ambient light level of any room is made up of direct or indirect
sunlight and the light fixtures in the room. The amount of ambient light
will determine how bright the image will appear. So, avoid direct light
on the screen as much as possible.
Windows that face the screen should be covered by opaque drapery
while the set is being viewed. It is desirable to install the projecting
system in a room whose walls and floor are of non-reflecting material.
The use of recessed ceiling lights and a method of dimming those
lights to an acceptable level is also important. Too much ambient light
results in a ‘wash out’ of the projected image. This appears as less
contrast between the darkest and lightest parts of the image. With
bigger screens, the ‘wash out’ becomes more important. As a general
rule, darken the room to the point where there is just sufficient light to
read or write comfortably. Spot lighting is desirable for illuminating
small areas so that interference with the screen is minimal.
What image size? How big should the image
be?
The projector is designed for projecting an image width from 1.4m
(4.6') to 6m (20') with an aspect ratio of 4 to 3. It leaves the BARCO
factory, adjusted as a ceiling/front projector for a screen width of
2.4m (7.8'). Changing the image size from the factory preset size
requires a realignment of the projector.
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
3-1
Installation guidelines
Where to install the projector ?
To indicate a correct installation position it is necessary to know :
•
The distance from projector to ceiling in case of Ceiling
mounted or the distance from projector to floor in case of Table
mounted;
•
The distance from projector to screen.
&HLOLQJ
3'
%
&'
$
3UR MHFWRU
6FUHHQ
To find the correct position for the projector, equipped with HD8
In metric :
PD[m] = 1.269 x SW[m] + 0.344
)UR QWYLHZ
A[cm] = 12 x SW[m] - 28.2
In inch :
PD[inch] = 1.269 x SW[inch] + 13.54
A[inch] = 0.12 x SW[inch] - 11.11
6FUHHQZLGWK
6:
Abbreviations used in the calculations and the drawings :
B
A
= Distance between ceiling and top of the screen (Ceiling
mounted) or distance between floor and bottom of the screen
(Table mounted).
= Correction Value, extra value to be added to B to obtain the
correct installation position (In some cases the A value can be
negative).
lenses, use the following formulas:
CD = Total distance between projector and ceiling (Ceiling mounted)
or total distance between projector and floor (Table mounted).
CD = A + B.
Ceiling Mounted : when the result is negative, enlarge the
distance between ceiling and top of the screen, mount screen
lower, until CD becomes zero or positive.
7RSYLHZ
•
•
Install the projector water levelled in both directions
Install the projector perpendicular to the screen
Used phosphor width on the CRT faceplate (e.g. green CRT)
11.5 cm (4.5 inch)
Table Mounted : when the result is negative, enlarge the
distance between floor and bottom of the screen, mount
screen higher, until CD becomes zero or positive.
SW = Screen width.
PD = Perpendicular distance between screen and projector's mount.
To obtain the right values, you can make use of the new option
included in the Installation Adjustment Mode to let the projector
calculate the parameters automatically. Please refer to Chapter 8 for
details.
Green
phosphor
green
phospho
Mounting Configuration
Ceiling Mount
To install the BARCOGRAPHICS 808s in the Ceiling configuration, use
BARCO'S Ceiling Mount Kit (CM100) - Order Number R9827341.
Installation instructions are included with this kit.
Table Mount
BARCO offers a heavy-duty projection table with adjustable height
which allows the projector to be correctly positioned perfectly to the
installation requirements. Order Number - R9827740.
3-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Installation setup
4
INSTALLATION SETUP
WARNING :
Risk of electric shock !
Installation only by BARCO authorized service personnel !
Access to Controls
Opening the top cover
During the projector setup and installation it is necessary to open the
top cover. Follow the procedure described below :
•
•
Turn the locking screw with a screwdriver counter clockwise;
Lift up and pivot the top cover.
WARNING :
The projector's top cover is not supported with locking hinge. Open
with care and support the cover with your hand.
Removing the top cover
During some installations, it will be convenient to remove the top cover
from the projector totally.
Proceed as follows :
•
•
Pivot the top cover backwards 90° (fully extended);
Push carefully the top cover to the left side (viewing from the rear
of the projector) until the hinges are disengaged. This can be
facilitated by pressing downwards on the spring tabs next to the
hinges. Slide the top cover off the projector.
Reinstalling the top cover
To reinstall the top cover on the projector :
•
Place the top cover in front of the hinges (as shown in the picture)
and push in the direction of the black arrow until the cover locks
into the hinges;
•
•
Pivot the top cover to close;
Secure the locking screw by turning it clockwise with a screwdriver.
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
4-1
Installation setup
Scan Adaptation
The scan switches must be placed in the correct position which corresponds to the desired scanning configuration.
To change the scanning, it is necessary to remove the projector top cover and to open the protection plate.
For opening the projector's top cover, see 'Access to controls'.
WARNING !
TURN OFF PROJECTOR AND UNPLUG THE POWER
CORD BEFORE CHANGING THE SCAN DIRECTION.
Getting access to the scan switches
•
Open the top cover and remove it from
the projector (see p.4-1);
•
Loosen the 3 retaining screws on each
side of the projector;
•
Open the protection plate and pivot it
forward (toward lenses).
Horizontal Scan Switches
Three switches are used, one for each CRT. When changing the
horizontal scan, insure that all three switches are set in the same
position. See positions of the switches (diagram on next page) for
the corresponding projector configuration.
To set the scan switches :
•
Remove the horizontal deflection module (the second module
viewing from the rear of the projector).
To remove the horizontal deflection module :
- Press the module lock and lift up the module handle;
Top view
Side view
Horizontal deflection module
Push
Top view
Side view
- Repeat this action on both sides of the module and extract the
module out of the main frame.
•
Toggle the 3 horizontal scan inversion switches (located just
underneath the horizontal amplitude module) to the correct
positions (see p.4-3).
•
Reinstall the horizontal deflection module.
Connectors for the
horizontal deflection module
Horizontal scan switches
Horizontal amplitude
module
4-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Installation setup
Vertical Scan Switch
One vertical switch is used for the three CRT's. See position of the
switch (diagrams) for the corresponding projector configuration.
To set the vertical scan switch :
•
Remove the vertical deflection module (the third module viewing
from the rear of the projector).
To remove the vertical deflection module :
Top view
Side view
Push
Top view
Vertical deflection module
Side view
- Press the module lock and lift up the module handle;
Vertical scan switch
- Repeat this action on both sides of the module and extract the
module out of the main frame.
•
•
Toggle the vertical scan inversion switch to the correct position.
Reinstall the vertical deflection module.
Connectors for the vertical
deflection module
Positions of the scan switches for the different mounting configurations are illustrated on the right side.
+RUL]RQWDO
9HUWLFDOVFDQ
VFDQVZLWFKHV
VZLWFK
)5217&(,/,1*
5($5&(,/,1*
)52177$%/(
5($57$%/(
After setting the scan switches, close the metal protection plate and
secure it with the retaining screws.
Close the top cover and reconnect the power cord to the wall outlet.
Note : Switching over from Floor to Ceiling or vice versa
requires a complete readjustment of picture geometry and
convergence.
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
4-3
Installation setup
To check the current positions of the scan switches,
proceed as follows:
Attention : This procedure can only be done after power (mains)
connection. So, first continue with the projector setup
and the connections and then return to this procedure.
•
Switch on the projector. The projector starts up on the last
selected source.
•
•
Press the <ADJUST> key.
Highlight 'SERVICE' by pushing the control stick forward or
backward and press the <ENTER> key: the 'SERVICE MODE
MENU' will be displayed.
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
Select with
or
then <ENTER>
<EXIT> to return
•
Highlight 'IDENTIFICATION' by pushing the control stick forward
or backward and press the <ENTER> key.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELETEABLOCK
DELETEALLBLOCKS
CHANGEPASSWORD
CHANGE LANGUAGE
RUN TIME
DYNAMICASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return
The projector will display the 'IDENTIFICATION SCREEN'.
This screen gives the current information about the projector
configuration in the line entitled 'Config'.
*5$3+,&6V
All projectors leave the factory set for a ceiling/front configuration.
4-4
Downloaded From projector-manual.com Barco Manuals
Proj. address : 001
Soft. Version : 5.00
Config. : Ceiling
front
Baudrate PC : 9600
Text : ON
Serial No. : 10359852
5975607 BARCODATA 808s 170397
Projector setup
5
PROJECTOR SETUP
The DIP switches on the controller board allow the SETUP of the
projector :
•
•
•
•
8 DIP switches for setting the projector address.
1 DIP switch for setting the powerup mode.
3 DIP switches for setting the baud rate for communication.
1 DIP switch for setting the password mode.
To gain access to the DIP switches :
-
Open the top cover.
-
Loosen the retaining screws of the metal protection plate and pivot
this plate to the lens side (Please refer to Chapter 4 'Installation
setup').
PASSWORD MODE
POWER UP MODE
The DIP switches are located on the back side of this metal protection
plate.
PASSWORD REQUIRED
FOR ADJUSTMENT
ON
YES
OFF
NO
OPERATING MODE WHEN
POWER IS SWITCHED ON
PLAYING
ON
OFF
StdBY
0
BAUD RATE TABLE
TO COMPUTER
CODE
0
1
2
3
4
5
6
7
PROJECTOR ADDRESS
(sum)
SPEED
110
150
300
600
1200
2400
4800
9600
RESERVED
POWER UP MODE
128
64
32
16
8
4
2
1
1
2
3
PASSWORD MODE
BAUD RATE CODE
(sum)
4
2
1
1
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
StdBY
MAIN POWER
PROCESSOR
CYC
PROCESS
CYCLE
II22CCSHORTED
SHORTED
BLOCK MATCH
ERROR
RCU
RCVDS
PC
PAUSE
OFF
ON
Setting the projector address
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled now by :
•
•
RCU for addresses between 0 and 9.
IBM PC (or compatible) or Apple MAC for addresses between 0 and
255.
0
Addressable with RCU
Addressable with PC, MAC
or workstation
9
255
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
5-1
Projector setup
Setting the address is a hardware SETUP of your projector which
must be done during installation. Use the 8 DIP switches provided on
the controller board labelled 'Projector Address'.
Each DIP switch has its own decimal value. The sum of the values
associated to those DIP switches gives the address. As shown in the
table, if Switch No. 1 is set to ON, it represents a decimal value of 128,
Switch No.2 for 64, Switch No.3 for 32, and so forth.
In the given example, the projector address is set to 202 :
DIP switch No.
: 1 2 3 4 5 6 7 8
Position ON/OFF : 1 1 0 0 1 0 1 0
0
Switch No
1
2
3
4
5
6
7
8
1
Value
1
2
3
4
5
6
7
8
128
64
32
16
8
4
2
1
Sum : 1x128 + 1x64 + 0x32 + 0x16 + 1x8 + 0x4 + 1x2 + 0x1 = 202
OFF ON
Factory preset address = 0
Note :
When the address button on the RCU is pressed, the projector will
display its own address on the screen. Once the address button is
pressed, to continue using your RCU, it is necessary to enter an
address, even when the displayed address is correct. Use the
numeric keys to enter the address.
For more information, please refer to the projector Owner's Manual .
PROJECTOR
ADRESS
001
Powerup mode
The projector can start up in two different modes. The start-up mode
is determined by the position of DIP Switch No. 4 of another set of 8
DIP switches on the controller board (one set of 8 switches are used
for projector address setting).
Position of the DIP Switch No. 4 (powerup mode) :
ON : operational mode.
OFF : standby mode (Factory preset).
Power-up mode
1
2
3
4
5
6
7
8
OFF ON
OFF
ON
•
Operational mode
When the power switch on the rear of the projector is pressed, the
projector displays the last selected source if available, otherwise it
remains on that source number until the source becomes available.
The on screen indication is only available when the "Text" function is
set to "ON".
Source 2
Fh= 15.6 kHz
Fv= 50 Hz
•
Standby mode
When the power switch on the rear of the projector is pressed, the
projector starts up in the standby mode. The standby key on the RCU
is used to turn the projector ON and OFF.
5-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Projector setup
Baud Rate for communication with a
computer
The communication speed between the projector and the computer
has 8 possible settings. With DIP Switch No. 6, No.7 and No.8 of the
8 DIP switches on the controller board, labelled as ‘Baud rate code
(sum)’, it is possible to select the baud rate (communication speed).
Each DIP switch has its own decimal value. The sum of the values
associated to those DIP switches gives the baud rate code. Each
baud rate code corresponds an communication speed.
0
1
1
2
3
4
5
6
7
8
Position of DIP switches and baud rate codes :
Binary Baud rate code
000
0
001
1
010
2
011
3
100
4
101
5
110
6
111
7
Speed
110
150
300
600
1200
2400
4800
9600
4
Baud rate
DIP switches
2
1
OFF ON
Factory preset baud rate = 9600
More information about computer communication with the
BARCOGRAPHICS 808s is available in the Projector Control Software manual.
Password mode
With DIP Switch No.5 of the second set of 8 DIP switches on the
controller board, the projector adjustments can be protected with a
password. When the password feature is enabled, the user has to
enter a password before he can enter the adjustment mode (For more
information about password setting and reprogramming the password, see Installation Adjustment).
When the password menus are disabled (adjust mode is unprotected), the adjust mode can be selected by pressing the <ADJUST>
key. This position of the DIP switch is useful for qualified service
technicians because they do not need a password to enter the adjust
mode.
Position of DIP Switch No.5 :
ON
: password mode enabled.
OFF : password mode disabled.
0
Password
mode
1
1
2
3
4
5
6
7
8
OFF ON
Factory preset password mode : OFF.
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
5-3
Projector setup
5-4
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
AC power connection
6
AC POWER CONNECTION
AC Power (mains) cord connection
Use the supplied cord to connect your projector to the wall outlet. Plug
the female power connector into the male connector at the back of the
projector.
7
KL VGHY L FH FRPS OL HVZL W
K SDUW RI
W
KH )&&U XOHV 2SHUD W
L RQL V VXEM HFWWR
IR OOR ZL QJ W ZR F RQ G LWL RQ V 7K LV
G LF \QRWF V K
I OLQW I
QF QG WKLVG
LF VW
FF W Q\LQW I
QF F L
G
LQFO GLQJLQW I
QF WK W
\F
V
QG VL GR
WLRQ
6H
H
L QV
WD
OO D
WLRQ L QV
WU
XFW
L RQV
EH
IRU
HF
R QQH
F
WLQ JWRWKH
V
XSSO \
9RLU OD
QRWLFH
G L QV
WD
O ODW
L RQDY D
QW
GH
UD
F
FRU
GHU
D
X U
p
VH
D
X
9 QRP
2))
21
,QRP
)UH T
POWE R / MAINS
9
5
SHULSKHUDOV
*
%
&RPS +6 \ QF 96\ QF
6
9
'
(2
2
21
9
'
(2
2
2KP
$
P
S
+]
COMM. P ORT
PORT 3
PORT 2
POR T 4/5
21
2KP
PORT 1
JUH H Q R S H U D WL R Q
U H G V WD Q G E \
PROJECT OR MODE
This projector may be connected to an IT-power system. The ITpower system is a power distribution system having no direct connection to earth. Instead, the exposed conductive parts of the electrical
installation are earthed.
9QRP
2))
21
POW ER
,QRP
)UHT
9
$PS
+]
/ M A IN S
Preparing your power cord
Mains lead (power cord) with CEE7 plug
As the colors of the wires in the mains lead of this apparatus may not
correspond with the colored markings identifying the terminals in your
plug, proceed as follows:
•
The yellow/green wire is ground and must be connected to the
terminal in the plug which is marked by the letter E or by the safety
earth symbol
or colored yellow and green.
•
The blue wire is neutral and must be connected to the terminal
marked with the letter N or colored black.
•
The brown wire is the line and must be connected to the terminal
marked with the letter L or colored red.
The wires of the delivered mains lead (power cord) are colored in
accordance with the following code :
Yellow and Green :
Ground (Earth).
Blue
:
Neutral.
Brown
:
Live.
Power cord with an ANSI 73.11 plug
The wires of the delivered mains lead (power cord) are colored in
accordance with the following code :
Yellow and Green : Ground (Earth).
White
: Neutral.
Black
: Live.
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
6-1
AC power connection
AC Power check
Check the power voltage which is determined by the ART. NR. (Article
number) included in the label pasted on the backside of the projector.
Projectors
connected
Projectors
connected
ART.NR.:RXXXXXXX
$UWQU[[[[[[[[[
6HULDOQU[[[[[[[
SER.NR.:RXXXXXXX
with the ART. NR. R9000901 and R9000902 must be
to a 230 VAC power source.
with the ART. NR. R9000908 and R9000907 must be
to a 120 VAC power source.
56,1
If the indicated voltage is different from that of the wall outlet, call a
qualified technician for power adaptation of the projector.
56287 5
5(027(
AC Input power (mains) voltage adaptation
Attention !
The BARCOGRAPHICS 808s - R9000901 and R9000902 leave the
factory to operate on a mains (power) input of 230 Vac.
The BARCOGRAPHICS 808s - R9000908 and R9000907 leave the
factory to operate on a mains (power) input of 120 Vac.
1
Adaptation of the power input of the projector between 230 Vac and
120Vac or vice versa is possible.
Follow the procedure as described below to adapt the voltage :
•
WARNING: turn off the projector and be sure the AC Power
Cord is unplugged before starting the procedure !
•
•
Open the top cover (see 'Access to controls' on p.4-1).
Unscrew the retaining screws of the AC power input board and
remove this board.
AC Power
input board
Power selector plug
Fuses
2
3
120V
230V
Power selector on 230V
•
Pull out the 'Power selector plug' (Photo 2) and reinsert it as
illustrated in Photo 3, depending on the AC power of the wall outlet
in the room.
•
Pull out the fuses and place the correct fuses in their sockets. See
the table below for the correct type of fuses.
•
Reinsert the power input board and secure it with the retaining
screws.
Power selector on 120V
Fuses
Warning !
For continued protection against fire hazard :
•
•
AC power
Fuses
Order Number
230 Vac
T6.3A/250V (2x)
R314145
120 Vac
T10A/250V (2x)
R314154
Replace with the same type of fuse.
Refer replacement to qualified service personnel.
6-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
AC power connection
Switching on the projector
Push the power (mains) switch located on the rear panel of the
projector to switch the projector ON and OFF :
•
•
If the switch is pressed in
: ON
9QRP
If the switch is Not pressed in : OFF
2))
21
POW ER
,QRP
9
)UHT
$PS
+]
/ M A IN S
The projector can be started up in the 'Operational mode' (image
displayed) or in the 'Standby mode', depending on the position of the
'Powerup' DIP switch on the controller board (see p.5-2). This DIP
switch is set during installation by a qualified technician. If you want
to change this start-up mode, call a qualified technician.
Power indication lamp :
OFF
power switch
: no power.
Green : projector in operational mode.
Red
: projector in standby mode.
When switching on the projector, with the power switch or via the
standby key on the RCU, the projector can start up in two ways if the
"CRT run in cycle" option is switched OFF :
•
•
A full white image (projector warm up) or
Immediately image display.
The way of starting up can be set in the service mode.
Starting up with a full white image
When the projector is set to start up with a full white image, the
"Projector warm up" menu will be displayed for 30 seconds.
Start up with "Warm up period"
If no action is taken, a white image will be displayed for 20 minutes.
This white image will be shifted on the faceplate of the CRT to avoid
CRT burn-in.
During this warm up period, it is possible to interrupt this white image
projection by pressing the <EXIT> key. The "Projector warm up" menu
will be redisplayed for another 30 seconds but with the remaining time
indicated.
If the <EXIT> key is pressed again, the remaining warm up period will
be skipped.
During the warm up period, every 30 seconds a text box with the
remaining time will be displayed on the screen for 2 seconds. This text
box will be displayed every time on another place to avoid CRT burnin.
If a key, other than the <EXIT> key, is pressed, a text box with the
following text will be displayed :
"Please use <EXIT> to leave this procedure."
PROJECTOR WARM UP
A FULL WHITE PATTERN WILL BE
GENERATED FOR 20 MINUTES.
FOR IMMEDIATE USE OF THE
PROJECTOR, PRESS <EXIT>.
WARNING: SKIPPING THIS
PROCEDURE CAN REDUCE THE
INITIAL PICTURE QUALITY OF
THE PROJECTED IMAGE.
THIS OPTION CAN BE DISABLED
IN THE SERVICE MENU.
REMAINING
PROJECTOR
WARM UP
TIME
18.5 MIN
PLEASE USE
<EXIT> TO
LEAVE THIS
PROCEDURE
Start up without "Warm up period"
If the <EXIT> key is pressed, the warm up period will be skipped and
the projector is immediately ready for use.
Warning : Skipping this warm up procedure can reduce the initial
picture quality of the projected image.
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
6-3
AC power connection
6-4
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Source connections
7
SOURCE CONNECTIONS
Signal input connection
The following signals can be connected to the projector through the
inputs on the back panel of the projector :
•
•
•
•
•
•
Composite Video
7KLVGH Y LF HF RP SOLH V ZLWKSDU W RI
WKH )& &U XOH V 2SH U DWLRQLV VXEMH F WWR
I R OO R ZL Q J WZ R F R Q G L W LR Q V 7 K L V
G
LF \QRWF
V K
I OLQW
6HHLQ VWDOODWLR QLQ VWUX FWLR QVE HIR UHFR QQ HFWLQ J WR WKHVXS S O\
S-Video
9RLUODQ R WLFHG
LQ VWDOODWLR QDY DQ WGHUDFFR UG HUDX UpVHDX
I
QF QGWKLVG
FF
W Q\LQW
LQFO GLQJLQW
QG VL GR
2))
RGB
9 QRP ,QRP
21
)UH T
P OWER / MAIN S
9
5
SH ULSKHU DOV
*
%
$PS
&RPS+6 \QF9 6\QF
6
9
'(2
2
21
9
'(2
2KP
2
21
2KP
I
I
LF QF F L
QF WK W
WLRQ
VW
G
\F
V
J U H H Q R S H U D W L R Q
U H G V W D Q G E \
+]
COMM. PO RT
P ORT 3
PORT 4/5
PORT 2
PO RT 1
PROJECT OR MODE
Component Video
RGB with Tri-level sync
3
4
5
2
1
Component video with Tri-level sync
Port No
1
2
Projector input
Numeric button
Composite Video
S-Video / Composite Video
Description of input signal
1
2
S-video : Y/C (luma/chroma).
The Composite video can also be connected to Port 2. It can be
selected inside the "Picture Tuning" menu. Please refer to the
Owner's Manual of this projector.
3
RGB
3
R, G and B with composite sync on Green;
R, G and B with separate composite or with separate Horizontal
and Vertical sync.
4/5
RGB
4 or 5
R, G and B with composite sync on Green;
R, G and B with separate composite or with separate
Horizontal and Vertical sync.
4/5
Component video
6
R-Y, Y, B-Y with composite sync on Y;
or with separate composite or with separate Horizontal and
Vertical sync.
4/5
RGB with Tri-level sync
7
R, G and B with Tri-level sync on Green;
R, G and B with separate Tri-level sync or with separate
Horizontal and Vertical Tri-level sync.
4/5
Component video
with Tri-level sync
8
R-Y, Y, B-Y with Tri-level sync on Y; or with separate Tri-level
sync or with separate Horizontal and Vertical Tri-level sync.
Only available when the optional Tri-level sync module is installed.
Connecting a Composite Video source to
Port 1
Composite video signals coming from a VCR, OFF air signal decoder
and so on can be connected to Port 1.
To select the video input :
Press the numeric button 1 on the RCU or the local keypad.
75 W Termination Switch for Video
75 Ω Termination Switch
Terminate the video input of the projector using the 75W switch next
to the video input, when the projector operates alone or when the
projector is the last unit in a loop-through configuration.
The switch is set to "ON" : signal terminated.
The switch is set to "OFF" : signal not terminated.
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
7-1
Source connections
Connecting a S-Video (or Composite Video)
source to Port 2
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS signals can be connected to Port 2 . The composite video
can also be connected to this port.
To select the S-video input :
Press the numeric button 2 on the RCU or the local keypad.
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3: luminance signal(Y)
1Vpp ±3dB
Pin 4: chrominance signal(C)
300mVpp ±3dB
For video:
Pin 1: earth(ground) video
Pin 2: not connected
Pin 3: video signal
Pin 4: not connected
3
1
2
4
In case of using Port 2 for connecting the Composite Video, the
selection of this source have to be done inside the "Picture Tuning"
menu. Please refer to the Owner's Manual of this projector.
75 Ω Termination Switch
75 W Termination Switch for S-video
Terminate the S-video input of the projector using the 75 W switch
next to the S-video input when the projector operates alone or when
the projector is the last unit in a loop-through configuration.
The switch is set to "ON" : signal terminated.
The switch is set to "OFF" : signal not terminated.
Connecting a RGB Analog source to Port 3
Connect a RGB Analog signal via an interface (e.g. RGB 120MHz
interface, part number 98 26570) to Port 3: RGB analog input with
automatic sync detection (Separate H and V sync inputs, with
composite sync input or with sync signals on green).
7
KLV GHY LFH F RPSOLHVZLWKSDU W RI
WKH)&&U XOHV 2SHU DWLRQLVVXEMH FWWR
IRO ORZL QJW ZRF RQGL W LRQV 7KLV
G LF \QRWF V K
I OLQW I
QF QGWKLVG LF V W
F F W Q\LQW I
QF F L G
LQFO GLQJLQW I
QF WK W
\F V
QG V L GR
WLRQ
6H
H LQ V
WD
O O D
WL RQ L QV
WUXFW
L RQ V
EHI
R U
H F
RQ QHF
WLQ J W
R W
K H
V
X SSO \
9RL UO D
QR WLFH
G
L QVW
DOO DW
L RQ DY DQWG H
U
DF
FRUGHU
DX U
pV
HD
X 9 QRP
2)) 21
, Q RP
)U H T
9
5
SHU LSKHU DOV
*
%
&RP S +6 \ QF 9 6\ QF
6
9
'
(2
2
21
9
'( 2
2KP
$
P
S
COMM. POR T
PORT 3
P O RT 4/ 5
PORT 2
21
2KP
+]
POWER / MAINS
2
POR T 1
J U H H Q R S H U D WL R Q
U H G V W D Q G E \
PROJ ECTOR MOD E
Pin configuration of the D9 (male) connector of the Analog input :
1
not connected
2
ground RGBS
3
RED
4
GREEN
5
BLUE
6
ground RGBS
7
ground RGBS
8
Horizontal /composite sync
9
Vertical sync
RGB 120MHz interface
RKPWH UP
L Q Y H U
To select the RGB analog Input :
Press the numeric button 3 on the RCU or the local keypad.
Locations of the Termination Resistors and Switches
on the RGB Input Auto Sync Tracking Module
When changing a switch position or removing a resistor, turn off the
projector and unplug the power cord from the wall outlet.
S2 Blue in Green (ON=yes)
75 W Termination resistors
In case of chaining (loop-through) the projectors, the 75W line
termination resistors must be removed from the RGB Input Auto Sync
Tracking Module when the projector is NOT the last unit in the chain.
In case of a stand-alone projector, do not remove the resistors.
75 W resistors on the module :
line terminated.
75 W resistors removed
line not terminated.
:
R101
Vsync
R81
Hsync
R41
(Blue)
R21
(Green)
R1
(Red)
S1 Force Negative Sync
(ON=yes)
Line termination 75 Ω resistors
7-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Source connections
Procedure to remove the line termination resistors :
•
•
•
Turn off the projector and unplug the projector power cord.
•
Unsolder and remove the resistors.
Remove the top cover from the projector (see p.4-1).
Remove the RGB Input Auto Sync Tracking Module from the main
frame.
To remove the RGB Input Auto Sync Tracking Module, follow the
same procedure as described in p.4-2 for removing the Horizontal
Deflection module :
•
•
Press the module lock and lift up the module handle;
Repeat this action on both sides of the module and extract the
module out of the main frame.
RGB Input Auto Sync Tracking Module
Blue in Green Switch on the RGB Input Auto Sync
Tracking Module
Blue characters are difficult to read, therefore the blue text will be
displayed as cyan so that the readability becomes better.
Switch in the ON position
: Blue in Green active.
Switch in the OFF position : Blue in Green disabled.
WARNING : Leaving the switch in the ON position will result in
abnormal color balance of the projected image.
Force Negative Sync on the RGB Input Auto Sync
Tracking Module
Switch in the ON position : the sync pulses must be negative.
Switch in the OFF position : the sync polarity will be automatically
detected.
Connecting a RGB Analog source to Port 4/5
RGB analog input terminals with separate H and V sync inputs,
composite sync input or sync signals on green can be connected to
the projector via Port 4/5. The projector automatically detects where
the sync signal is located.
An interface is recommended when connecting a computer and local
monitor to the projector. BARCO provides the following interfaces :
•
•
Universal Analog Interface - Order number : R9826100.
Interface
RGB 120 MHz Analog Interface - Order number : R9826570.
RK PW H UP
LQ YHU To select the RGB input :
Press the numeric button 4 or 5 on the RCU or the local keypad.
Connecting a Component Video source to
Port 4/5
A component video (R-Y, Y, B-Y) with sync signals can be connected
to the projector via Port 4/5. The projector automatically detects
where the sync signal is located.
7
KL V GHYL FH FRPSO L HVZL W
K SDUW RI
WKH)&&U XOHV 2SHUDWLR QL VVXEM HFW
W
R
6HH
L QV
WD
O OD
WL RQL QV
WU
XFW
L RQV
EH
I
RUH
F
RQQHF
W
L QJ W
R W
KHVXSSO\
IR OO RZL QJ W ZR F RQ GL WLR QV 7KL V
G LF \QRWF V K
I OLQW I
QF QG WKLVG LF VW
FF W Q\LQW I
QF F L G
LQFO GLQJLQW I
QF WK W
\F V
QG VL GR
WLRQ
9RL U
ODQRWLFH
G
L QV
WD
O ODW
L RQDYDQW
GH
U
DF
F
RUGH
UD
X Up
V
H
DX
9QRP
2))
21
,QRP
)UH T
P OW ER / MAINS
9
5
SHULSKHUDOV
*
%
&RPS+6\ QF96\ QF
6
9
'
(2
2
21
9
'
(2
2KP
$
P
S
2
21
J U H H Q R S H U D W L R Q
2KP
U HG VWDQ GE \
+]
COMM. P ORT
P ORT 3
POR T 4 /5
PORT 2
PORT 1
PROJECT OR MODE
An HDTV interface is recommended when connecting a computer
and local monitor to the projector. The HDTV Kit Order number :
R9828040.
To select the component video input :
Press the numeric button 6 on the RCU or the local keypad.
798
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
7-3
Source connections
Connecting a RGB Analog source with Trilevel sync to Port 4/5 (option)
7KL VG HY LF H FR P
S OLH VZL WK SDUW RI
WK H) &&UX OHV 2S HUD WLR QL VV XE MH FW WR
6HHLQVW D
O ODWLR QL QVWUX FWLR QVE H
I RUHFR QQ HF
W LQJ WR WK H
VXSS O\
IR OO R ZL Q J WZR FR QG L WL RQ V 7K L V
9RL UODQ RWL FH
G
LQVWDO ODWLR QDY DQ WGH UDF
FR UGHU DXU p
VHDX
G
LF I
Q
F QG
W
K
L V
G
FF
LQF
O
RGB analog input terminals with Tri-level sync input or with Tri-level
sync on green can be connected to the projector via Port 4/5. The
projector detects automatically where the sync signal is located. This
feature requires an optional Tri-Level Sync Module - Order Number
R9828040.
9QRP ,QRP
)UH T
9
5
S
H UL S
K
H UDOV
*
%
&RP S+6\QF 96\QF
6
9
'(2
2
2
1
9
'(2
2
2
KP
$
P
S
21
I
I
G
R
V K
I OLQW
LF Q
F F L
Q
F W
K W
V
W
G
\F
V
W
L R
Q
J U H H Q R S H U D W L R Q
2KP
U H G V W D Q G E \
+
]
POWER / MAIN S
\
Q
RW
F
W Q\LQ
W
G
L Q
J
LQ
W
QG V
L
2)) 21
COMM. POR T
PORT 2
PO R T 4/5
POR T 3
PORT 1
PR OJECTOR MODE
To select the input :
Press the numeric button 7 on the RCU or the local keypad.
798
Connecting a Component Video source with
Tri-level sync to Port 4/5 (option)
7KL VG HY LF H FR P
S OLH VZL WK SDUW RI
WK H) &&UX OHV 2S HUD WLR QL VV XE MH FW WR
6HHLQVW D
O ODWLR QL QVWUX FWLR QVE H
I RUHFR QQ HF
W LQJ WR WK H
VXSS O\
IR OO R ZL Q J WZR FR QG L WL RQ V 7K L V
9RL UODQ RWL FH
G
LQVWDO ODWLR QDY DQ WGH UDF
FR UGHU DXU p
VHDX
G
LF I
Q
F QG
W
K
L V
G
FF
LQF
O
Component video inputs with Tri-level sync signal can be connected
to the projector via Port 4/5. The projector detects automatically
where the sync signal is located. This feature requires an optional TriLevel Sync Module - Order Number R9828040.
9QRP ,QRP
)UH T
POWER / MAIN S
9
5
S
H UL S
K
H UDOV
*
%
&RP S+6\QF 96\QF
6
9
'(2
2
2
1
9
'(2
2
KP
$
P
S
2
21
\
Q
RW
F
W Q\LQ
W
G
L Q
J
LQ
W
QG V
L
2)) 21
G
R
I
I
V K
I OLQW
LF Q
F F L
Q
F W
K W
V
W
G
\F
V
W
L R
Q
J U H H Q R S H U D W L R Q
2KP
U H G V W D Q G E \
+
]
COMM. POR T
POR T 3
PO R T 4/5
PORT 2
PORT 1
PR OJECTOR MODE
To select the input :
Press the numeric button 8 on the RCU or the local keypad.
Peripheral equipment
798
Connecting a RCVDS 05 source selector to the
BARCOGRAPHICS 808s
•
•
•
•
Up to 20 inputs with a RCVDS05 and up to 90 inputs can be
accommodated when multiple RCVDS source selectors are linked
via a Expansion Module.
Serial communication with the projector.
Remote control buttons on the RCVDS05 to control the BARCO
GRAPHICS 808s (source selection and analog settings).
The selected source number will be displayed on a 2-digit display
and the selected input modules will be indicated with a LED on the
rear.
The order numbers for the RCVDS05 source selector :
RCVDS05 230 V
R9827880
RCVDS05 120 V
R9827889
For more information about the use of the RCVDS05, consult the
RCVDS05 Owner's Manual - order number : R5975765.
Connecting a VS05 source selector to the
BARCOGRAPHICS 808s
The VS05 can switch up to 5 Composite Video sources, 3 S-Video
Sources and 1 RGB analog or component Video source to the
BARCOGRAPHICS 808s. In addition, the audio signal associated
with the source, can be switched to an audio amplifier.
VS05 order number : R9827890.
For more information about the use of the VS05, consult the VS05
Owner's Manual - order number : R5975245.
Connecting an IR Remote Receiver 800 to the
BARCOGRAPHICS 808s
This infrared Remote Receiver makes it possible to control the
BARCOGRAPHICS 808s from another room. There is a communication cable between the IR Remote Receiver and the projector. The
control information from the RCU can now be sent to the IR Remote
Receiver 800. The IR Remote Receiver 800 displays the selected
source on a 7-segment display.
IR Remote Receiver 800 order number : R9827515.
7-4
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Installation adjustment mode
8
INSTALLATION ADJUSTMENT MODE
Before starting any adjustment.
The BARCODATA 808s is factory optimized for a screen with range 1.9m (74.8 inch) to 3.2m (126.0 inch)
You wish an optimal focused image
for a screen width between 1.2m to 1.9m
or between 3.2m and 6m?
then,
carry out the following mechanical adaptation :
Mechanical adaptation procedure (adding washers between lens and picture tube support)
The screen width adjustment for the installed lens is divided into 3 ranges. Within these ranges, the focus can be optimal adjusted.
range 1
min. SW : 1.20 m (47.2 inch)
max. SW : 1.90 m (74.8 inch)
range 2
min. SW : 1.90 m (74.8 inch)
max. SW : 3.20 m (126.0 inch)
range 3
min. SW : 3.20 m (126.0 inch)
max. SW : 6.00 m (236.0 inch)
5975607 BARCODATA 808s 120397
Downloaded From projector-manual.com Barco Manuals
8-1
Installation adjustment mode
Adaptation procedure :
1. Open and remove the top cover
723&29(5
2. Remove the lenses by :
- remove for each lens the 4 nuts, holding lens to picture tube
support (nutdriver 8 mm).
- remove the lens from the bolts
Le ns nut
LENSES
3. Placing the required washers :
a) optimal focus in the screen width range 1.20 m - 1.90 m
b) optimal focus in the screen width range 1.90 m - 3.20 m
2xGr
4xGr
3xBl
2xGr
1xBl
3xGr
2xBl
2xGr
3xGr
2xBl
3xGr
2xBl
2xGr
4xGr
3xBl
2xGr
1xBl
3xGr
2xBl
2xGr
1xGr
1xBl
1xBl
%ODFN ZDVKH U
*UH\ZDVKHU $O
1xGr
1xBl
1xBl
c) optimal focus in the screen width range 3.20 m - 6.00 m
4. Reinstall the lenses and secure the lenses with the available nuts.
1xGr
1xBl
TO P CO VER
1xGr
1xBl
1xGr
1xBl
1xGr
1xBl
1xGr
1xBl
1xGr
1xBl
0xGr
0xBl
%ODFN ZDVKHU
0xGr
0xBl
8-2
Downloaded From projector-manual.com Barco Manuals
*UH \ZDVKHU$O
5975607 BARCODATA 808s 120397
Installation adjustment mode
5. Reinstall top cover.
6. Proceed to image focus adjustment
Access to Installation Adjustment Mode
It will be necessary to perform several mechanical adjustments while
in the Installation Adjustment Mode. It will be required to open and
remove the projector's top cover in order to gain access to the
adjustment points.
ADJUSTMENT MODE
Select a path from
below:
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
To enter into the installation adjustment mode :
•
•
Press the <ADJUST> key to start up the adjustment mode.
•
A warning will be displayed on the screen. If you are a qualified and
authorized service person, press the <ENTER> key to start up the
installation mode. Otherwise, press the <EXIT> key to return.
•
•
Push the control stick forward or backward to highlight the path
INSTALLATION in the "Adjustment mode" menu and then press
the <ENTER> key.
WARNING
RISK OF ELECTRICAL SHOCK
NO USER ADJUSTABLE PARTS
INSIDE
THE FOLLOWING
INSTALLATION MENUS
ARE RESERVED TO,
AND TO BE PERFORMED ONLY
BY BARCO PERSONNEL, OR
BARCO AUTHORIZED DEALERS
When entering the installation mode, the projector will automatically switch to the internal pattern on 15 kHz/50 Hz.
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
When the password mode is active (see p.5-3), you will be
requested to enter the 4 digit password.
Enter the digits with the numeric keys on the RCU or the local
keypad.
Example : Password as 2 3 1 9
For each digit entered, a 'X' appears on the screen under the
displayed text 'enter password'.
enter
password
xxxx
197
If the entered password is correct, you get access to the 'Installation Adjustment Mode'.
If the entered password is wrong, The message "Wrong password!!!" will be displayed. The projector stays on the previous
selected item.
Factory programmed password :
enter
0000
password
Wrong
Password !
xxxx
197
Overview flowchart of the Installation Adjustment Mode
Adjustment Mode
Installation
Projector Distance
Optical Lens Focusing
Raster Centering
CRT Projection Angle Adjustment
5975607 BARCODATA 808s 120397
Downloaded From projector-manual.com Barco Manuals
8-3
Installation adjustment mode
Important : Access to adjustments
The top cover of the projector should be removed in order to gain
access to the adjustments.
Please refer to p.4-1 for how to remove the top cover.
Projector Distance
On the screen, a drawing will be displayed together with parameters
indicating a correct installation position.
To change the screen width :
•
•
•
•
•
•
•
&HLOLQJ
3'
%
&'
$
Push the control stick to the left or to the right to highlight the item
SW in the "Projector Distance 1" menu and then press the
<TEXT> key.
If the <ENTER> key is pressed, the "Optical Lens Focusing" will be
displayed.
3URMHFWRU
6FUHHQ
If the <EXIT> key is pressed, the projector will return to the
previous menu.
A = Correction value
PD= Perpendicular distance between screen and projector
)URQWYLHZ
SW= Screen
width
After the <TEXT> key is pressed, the next menu "Projector
Distance 2" will be displayed on the screen. It allows the user to
change the Screen width.
Push the control stick to the left or to the right to highlight the digit
needed to be changed, and enter the desired digit with the numeric
keys on the RCU or the local keypad.
Press the <ENTER> key to confirm the changes. The projector will
redisplay the "Projector Distance 1" menu with updated values for
the three parameters.
Press the <ENTER> key to continue with the "Optical Lens
Focusing".
If the <EXIT> key is pressed, the projector will return to the
previous menu.
SW = 2.6 m
PD= 3.64m
A=12 cm
Select with arrow keys; <TEXT> to reprogram
<ENTER> to continue; <EXIT> to return.
WARNING: ONLY FOR STANDARD PROJECTORS !!
6FUHHQZLGWK
6:
SCREENWIDTH = 2 , 6 0 m
Select with arrow keys; reprogram with numeric keys and
then <ENTER> to confirm.
Maximum screenwidth = 6 m
Maximum proj. distance = 7RSYLHZ
8,1 m.
The same applies to the PD (projector distance). You can use the
above-mentioned procedure to obtain a correct updated value of SW
(screenwidth) after entering a new value of PD (projector distance).
Optical Lens Focusing
The optical focusing procedure is performed separately for each
lens. The appropriate CRT will be switched on as the user proceeds
through the optical focusing adjustment sequence.
Each lens has two focus adjustment points, one at the rear of the lens
and one at the front. The center of the projected image is focused by
loosening the wing nut at the rear end of the lens and rotating the lens
barrel until the center of the image is clearly focused. The corners of
the projected image are focused by loosening the wing nut at the front
end of the lens and rotating the lens barrel until the corners of the
image are clearly focused. Repetition of these adjustments may be
necessary to optimize optical focusing.
Press the <ENTER> key to continue. After finishing focusing of the
three lenses, press the <ENTER> key to enter the Raster centering.
Press the <EXIT> key to return to operational mode.
Press the <ADJUST> key to return to operational mode.
237,&$//(16)2&86,1*
1. LOOSEN THE NUT ON THE
REAR OF THE GREEN LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE GREEN LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
<ENTER> to continue
<EXIT> to return
237,&$//(16)2&86,1*
1. LOOSEN THE NUT ON THE
REAR OF THE RED LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE RED LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
<ENTER> to continue
<EXIT> to return
237,&$//(16)2&86,1*
1. LOOSEN THE NUT ON THE
REAR OF THE BLUE LENS,
ROTATE THE LENS BARREL
TO FOCUS THE CENTER
OF THE IMAGE,
THEN TIGHTEN THE NUT
2. LOOSEN THE NUT ON THE
FRONT OF THE BLUE LENS
AND ROTATE THE FRONT
SECTION OF THE LENS TO
FOCUS THE CORNERS OF THE
IMAGE, THEN TIGHTEN THE NUT.
Center focusing
<ENTER> to continue
<EXIT> to return
Corner focusing
8-4
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 120397
Installation adjustment mode
Raster Centering
The raster must be centered on the CRT faceplate of each tube,
therefore, it is necessary to look into the lenses.
5$67(5&(17(5,1*
Caution : To avoid eye discomfort while performing these adjustments, reduce the contrast and gradually increase the brightness
level until the raster becomes visible behind the image.
Warning : In order to ensure maximum CRT
longevity and to avoid CRT damage, do not shift
the raster outside the phosphor area of the CRT.
Press the <ENTER> key to display the raster on the green CRT.
CONTRAST LEVEL IS REDUCED
AND BRIGHTNESS INCREASED
TO MAKE THE RASTER
VISIBLE ON THE FACE PLATE
OF EACH CRT.
USE THE ARROW KEYS
TO CENTER THE RASTER
ON THE GREEN, RED AND
BLUE CRT RESPECTIVELY
<ENTER> to continue
<EXIT> to return
Forbidden area
Projected raster
Look into the green lens and shift the raster with the control stick until
it is centered in the middle of the CRT faceplate.
Press the <ENTER> key to activate the raster on the Red CRT
faceplate.
Shift the Red raster with the control stick until the raster is centered
on the CRT faceplate.
CRT faceplate border
Phosphor area
Press the <ENTER> key to activate the raster on the Blue CRT
faceplate.
Shift the Blue raster with the joy stick until the raster is centered on the
CRT faceplate.
Press the <ENTER> key to continue with the CRT projection angle
adjustment.
Correct raster position
Press the <EXIT> key to return to Optical focusing.
Press the <ADJUST> key to return to Operational mode.
Wrong raster position
5975607 BARCODATA 808s 120397
Downloaded From projector-manual.com Barco Manuals
8-5
Installation adjustment mode
CRT Projection Angle Adjustment
The projection angle of the red and blue CRT's is dependent on the
desired size of the projected image. If the centers of green, blue and
red do not coincide, the CRT projection angle must be adjusted.
NOTE : Never try to correct this misalignment with the shift
correction or the static convergence controls. These controls may
only be applied to correct small errors which cannot be corrected
by the CRT angle adjustment.
Note: The Horizontal Shift and Vertical Shift for Red and Blue
should be set near 50%.
CRT PROJECTION ANGLE
ADJUSTMENT
CRT PROJECTION ANGLE IS
THE FIRST STEP OF STATIC
CONVERGENCE ADJUSTMENT.
IT IS CRITICAL THAT THE
RASTERS ARE CENTERED ON
THE CRT FACE PLATES
PRIOR TO PERFORMING
THIS STEP.
...
<ENTER> to read more
<EXIT> to return
CRT PROJECTION ANGLE
ADJUSTMENT
Be sure that the rasters are centered on the CRT faceplate.
DURING THIS PROCEDURE,
RED ON GREEN AND THEN
BLUE ON GREEN CROSSHAIRS
WILL BE DISPLAYED
TO ALLOW THE RED AND
BLUE CRTS TO BE ALIGNED
WITH THE GREEN CRT.
Press the <ENTER> key to start the CRT angle adjustment procedure.
Press the <ENTER> key to continue with the second part of the CRT
projection angle adjustment.
LOOSEN BOLTS A AND B
TO PIVOT THE RED CRT,
AND BOLDS C AND D
TO PIVOT THE BLUE CRT.
<ENTER> to continue
<EXIT> to return
Press the <ENTER> key to continue with the crosshairs alignment.
Press the <EXIT> key to return to the previous menu.
Press the <ADJUST> key to return to Operational mode.
Loosen bolts A, B, C and D to pivot the red CRT until the center of the
Red image and the center of the Green image coincide. When the
angle of the red CRT is corrected, tighten the four bolts.
Press the <ENTER> key to continue with blue and green crosshairs.
Press the <EXIT> key to return to the CRT projection angle adjustment menu.
CRT
PROJECTION ANGLE
ADJUSTMENT
Red crosshair
Green crosshair
Align crosshairs
<ENTER> continue
<EXIT> to return
Move the red CRT towards
the green CRT
$ %
& '
( )
* +
Red crosshair
Green crosshair
Move the red CRT to the
outside, away from the
green CRT
8-6
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 120397
Installation adjustment mode
Loosen bolts E, F, G and H to pivot the blue CRT until the center of the
Blue image and the center of the Green image coincide. When the
angle of the blue CRT is corrected, tighten the four bolts.
Press the <ENTER> key to continue with the diagonal focusing menu.
Press the <EXIT> key to return to the CRT projection angle adjustment.
CRT
PROJECTION ANGLE
ADJUSTMENT
Blue crosshair
Green crosshair
Move the blue CRT to the
outside, away from the green
CRT
Align crosshairs
<ENTER> continue
<EXIT> to return
Blue crosshair
Green crosshair
Move the blue CRT towards
the green CRT
Projection angle correctly aligned for screen width SW1.
The same projection angle is misaligned for new screen width SW2.
Realignment is necessary. Each screen width change requires
readjustment of the projection angle.
SW2
(SW1 > SW2)
370b
5975607 BARCODATA 808s 120397
Downloaded From projector-manual.com Barco Manuals
8-7
Installation adjustment mode
8-8
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 120397
Messages, warnings and failure codes
9
MESSAGES, WARNINGS AND FAILURE CODES
SOURCE 01
Fh= 15.6 kHz
Fv= 050 Hz
SOURCE 01
Fh= 15.6 kHz
Fv= 050 Hz
enter
password
xxxx
text on
text off
PROJECTOR
ADDRESS :
003
WARNING :
input not
available
When selecting a new source,
information about this source will
be displayed on the screen.
Source number, horizontal and
vertical frequencies of the
displayed source.
Announcement of the selected
source.
Message to enter your password.
Password contains 4 digits.
These messages will be
displayed on the screen when
pushing the <TEXT> key.
Text ON : the 'Bar scale
indication' will be enabled during
the change of an analog control
in the 'Operational mode'. All
warning and failure messages
will be displayed.
WARNING :
source not
available
The input is a valid input but the
source is not connected to the
input terminals or the input source
is switched off.
WARNING :
invalid
key entry
WARNING :
invalid
code entry
When a wrong key is pressed on
the RCU.
Message when the entered
password is wrong.
WARNING :
end of adjust range
End of adjustment range.
WARNING :
input no
longer
available
Message will be displayed when
the input source is no longer
available. The following message
then appears: 'check input
signal or select new source'.
Indication of the projector
address when activating the
'ADDRESS' button on the RCU
with a pencil or other small
object.
check input signal
or select
new source
This message will be displayed
after the message 'input no longer
available'. It asks to check the
connections between the source
and the projector or to check if
the source is switched on.
When using the projector with
the RCVDS, this warning will be
displayed when selecting an
input slot of an RCVDS where
the input board is missing.
WARNING :
input selector
not
available
It warns you to check the power
connection or the power status
of the RCVDS.
Next message will appear
immediately on the screen : 'go
to standby'.
Text OFF : the 'Bar scale
indication' will be disabled
during the change of an analog
control in the 'Operational mode'.
All warning and failure massages
will not be displayed.
5975607 BARCODATA 808s 120397
Downloaded From projector-manual.com Barco Manuals
9-1
Messages, warnings and failure codes
WARNING :
Projector will switch to 'Standby'
when the RCVDS is no longer
available.
FAILURE
RCVDS communication
error
WARNING :
invalid
frequency
input
The entered frequency or
applied frequency of the source
is out of the projector's range.
FAILURE
RWI communication
error
Hardware failure.
Call a
qualified service technician.
WARNING :
default
settings
loaded in
the E2PROM
Adjustment settings are lost.
Reload using Projector Control
Software via PC or MAC (if this
option is available), or readjust
image.
FAILURE
IRIS communication
error
Communication error between
IRIS and the projector. Call a
qualified service technician.
table is
deleted
Message to inform that selected
table is deleted. This message
will be followed by 'confirm
message', on which the user has
to answer.
WAIT
starting
up
IRIS
FAILURE
invalid
RWI soft
version
Wrong software version in your
projector.
Call for technical support.
go to
stand by
FAILURE
I2C error
addr. : 7FH3
Hardware failure.
Call a
qualified service technician for
repair.
FAILURE
short
circuit on
I2C bus
Hardware failure.
Call a
qualified service technician for
repair.
9-2
Downloaded From projector-manual.com Barco Manuals
Serial communication error
between RCVDS and projector.
Message during the start up of
the IRIS.
Message will disappear when the
IRIS is ready to accept commands.
5975607 BARCODATA 808s 120397
Appendix A: BARCO ceiling mount support
A
BARCO CEILING MOUNT SUPPORT
This appendix gives only an overview of the contents of the installation guidelines and some overview drawings.
The installation guidelines for the BARCO ceiling mounting support
can be ordered from BARCO. The order number: R5975693.
Contents of the installation guidelines
Overview drawing of the total system
1. Mounting instructions for the upper support to the ceiling
a. Position of the upper support on the ceiling
b. Mounting of the 4 screwed rods on the upper support
2. Projector placement on lower support
a. Projector placement on support
b. Location of controls for projector-position correction
3. Mounting instructions of the cord to lift up the projector
a. Mounting the cord support on the upper support
b. Cord insertion between the upper and lower support
c. Cord fixation
4. Lifting up and fixing the lower support (with projector) on the
screwed rods
5. Alignment of the projector-support assembly
a. Projector water-level adjustment
b. Adjustment "projector axis perpendicular" to the screen surface
c. Projector movement forward or backward
Exploded view of BARCO ceiling mount
support
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
A-1
Appendix A: BARCO ceiling mount support
Projector position corrections
•
Water-level adjustment
D
•
Projector axis adjustment
C
A-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Appendix B: G2 adjustment
B
G2 ADJUSTMENT
Once the on-screen menu "G2 ADJUSTMENT" is displayed, proceed
as follows :
*$'-8670(17
Use the potentiometers
on the G2-ADJ. module
to set the screen grid
voltage for Red,
Green and Blue.
Adjust until the LED
on the corresponding
output amplifier is
turned off.
<EXIT> to return
•
•
Remove the top cover from the projector (see p.4-1) and open the
front metal protection cover by turning out the 3 retaining screws on
both sides.
1
A green LED is mounted on each of CRT sockets (see Photo 2).
When selecting the G2 adjustment menu, these green LEDs must
be out. If not, follow the procedure below to adjust the G2 :
- Open the second metal cover by turning out the retaining screws
on both sides and pivot the cover to the front side of the projector
(see Photo 1);
- Adjust the G2 potentiometers (see Photo 3) very slowly with a
plastic tweaker until the LED of the corresponding amplifier just
stops illuminating. Repeat the adjustment for the other colors;
Retaining screws
- After the three G2 potentiometers have been correctly adjusted,
close both metal covers and secure with the retaining screws.
3
Red potentiometer
Green potentiometer
Blue potentiometer
2
Green LEDs
After finishing the adjustments :
Press the <ENTER> key to continue with the "SERVICE" menu.
Press the <EXIT> key to return to the "SERVICE" menu.
Press the <ADJUST> key to return to Operational mode.
5975996 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
B-1
Appendix B: G2 adjustment
B-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Gamma corrections
C
GAMMA CORRECTIONS
When entering the gamma corrections, a warning will be displayed :
"RISK OF INCORRECT ADJUSTMENT OF THE PROJECTOR.
THE GAMMA CORRECTIONS ARE FACTORY ADJUSTED USING
AN ACTAS COLOR ANALYZER ! THEREFORE, ONLY QUALIFIED
INSTALLATION OR SERVICE PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS ! "
If you are qualified, press the <ENTER> key to continue.
Gamma Corrections
Three items can be selected inside the "Gamma Corrections" menu:
the Blue Gamma Correction, the R & B midlights and the factory
preset.
To carry out the Blue Gamma Correction :
•
Push the control stick forward or backward to highlight the item
BLUE GAMMA CORRECTION in the menu and then press the
<ENTER> key.
If the <EXIT> key is pressed, the projector will return to the Service
menu.
•
After the <ENTER> key is pressed, a text box with the message,
"Adjust with arrow key", will be displayed on the screen.
•
Push the control stick forward or backward to adjust the slope, a
text box with a bar scale (Min to Max) will be displayed to visualize
the magnitude of the correction.
•
Push the control stick to the left or to the right to adjust the
breakpoint, a text box with a numeric bar scale (0-99) will be
displayed to visualize the magnitude of the correction.
•
Press the <ENTER> key to return to the "Gamma Corrections"
menu.
WARNING
RISK OF INCORRECT
ADJUSTMENT OF THE
PROJECTOR.
THE GAMMA CORRECTIONS ARE
FACTORY ADJUSTED USING AN
ACTAS COLOR ANALYZER !
THEREFORE, ONLY QUALIFIED
INSTALLATION OR SERVICE
PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS !
<ENTER> TO CONTINUE
<EXIT> TO RETURN.
GAMMA CORRECTIONS
BLUE GAMMA CORRECTION
Adjust slope with é or ê
Breakpoint with ç or è
R & B MIDLIGHTS
Adjust red with é or ê
blue with ç or è
FACTORY PRESET
Select with é or ê
then <ENTER>;
<EXIT> to return.
Adjust with arrow key
BLUE GAMMA
SLOPE
Min
Max
BLUE GAMMA
BREAKPOINT
50
5975607 BARCODATA 808s 170397
Downloaded From projector-manual.com Barco Manuals
C-1
Gamma Corrections
To carry out the Red and Blue Midlights Correction :
•
Push the control stick forward or backward to highlight the item
R & B MIDLIGHTS in the menu and then press the <ENTER> key.
If the <EXIT> key is pressed, the projector will return to the Service
menu.
•
•
After the <ENTER> key is pressed, a text box with the message
"Adjust with arrow key", will be displayed on the screen.
Push the control stick forward or backward to adjust the Red
Midlights, a text box with a bar scale (0-16) will be displayed to
visualize the magnitude of the correction.
•
Push the control stick to the left or to the right to adjust the Blue
Midlights, a text box with a bar scale (0-16) will be displayed to
visualize the magnitude of the correction.
•
Press the <ENTER> key to return to the "Gamma Corrections"
menu.
GAMMA CORRECTIONS
BLUE GAMMA CORRECTION
Adjust slope with é or ê
Breakpoint with ç or è
R & B MIDLIGHTS
Adjust red with é or ê
blue with ç or è
FACTORY PRESET
Select with é or ê
then <ENTER>;
<EXIT> TO RETURN.
Adjust with arrow key
RED
MIDLIGHTS
8
BLUE
MIDLIGHTS
8
To set the parameters back to the factory preset values :
•
•
Push the control stick forward or backward to highlight the item
FACTORY PRESET in the menu and then press the <ENTER>
key.
Press the <EXIT> key to return to the Service menu.
GAMMA CORRECTIONS
BLUE GAMMA CORRECTION
Adjust slope with é or ê
Breakpoint with ç or è
R & B MIDLIGHTS
Adjust red with é or ê
blue with ç or è
FACTORY PRESET
Select with é or ê
then <ENTER>;
<EXIT> to return.
C-2
Downloaded From projector-manual.com Barco Manuals
5975607 BARCODATA 808s 170397
Form Approved
Bureau Budget No. 45-R0338
MATERIAL SAFETY DATA SHEET
MANUFACTURER'S NAME AND FSCM (Federal Supply Code for Manufacturer's)
BARCO N.V.
EMERGENCY PHONE NO.
32-56-368211
SECTION I
ADDRESS (Number, Street, City, State, and ZIP Code)
Noordlaan 5 B-8520 KUURNE
CHEMICAL NAME AND SYNONYMS
Ethylenglycol & Glycerol
TRADE NAME AND SYNONYMS
Cooling liquid 512334
CHEMICAL FAMILY
Polyalcohols
FORMULA
FEDERAL STOCK NUMBER (FSN)
GROSS WEIGHT (LBS)
C2H6O2+C3H8O3
OUTSIDE PACKAGE DIMENSIONS (Inches)
MIL-STD-1341/NATIONAL FIRE PROTECTION ASSOCIATION STD 704M SIGNAL
FLAMMABILITY....................
HEALTH..................
REACTIVITY.................
SECTION III
PHYSICAL DATA
SECTION II - HAZARDOUS INGREDIENTS
PAINTS, PRESERVATIVES, AND
SOLVENTS
TRESHOLD LIMIT
VALUE (Units)
%
ALLOYS AND METALLIC COATINGS
PIGMENTS
BASE METAL
CATALYST
ALLOYS
VEHICLE
METALLIC COATINGS
SOLVENTS
FILLER METAL
PLUS COATING OR CORE FLUX
ADDITIVES
OTHERS
SPECIFIC HAZARD.............
%
TRESHOLD LIMIT
VALUE (Units)
%
TRESHOLD LIMIT
VALUE (Units)
OTHERS
HAZARDOUS MIXTURES OF OTHER LIQUIDS, SOLIDS, OR GASES
BOILING POINTS (°C.)
201°C
SPECIFIC GRAVITY (H2O=1)
VAPOR PRESSURE (mm Hg.)
3 mm Hg
PRECENT VOLATILE
BY VOLUME (%)
VAPOR DENSITY (AIR=1)
2.2
EVAPORATION RATE
(.............................=1)
1.15
SOLUBILITY IN WATER
SECTION IV - FIRE AND
EXPLOSION HAZARD DATA
APPEARANCE AND ODOR
DD
FLASH POINT (Method used)
FLAMMABLE LOWER EXPLOSIVE LIMIT
LIMITS
UPPER EXPLOSIVE LIMIT
EXTINGUISHING MEDIA
SPECIAL FIRE FIGHTING PROCEDURES
UNUSUAL FIRE AND EXPLOSION HAZARDS
FORM
1 JUN 71
1813 *
GPO 794/043/30
Downloaded From projector-manual.com Barco Manuals
S/N 0102-026-1080
SECTION V
HEALT HAZARD DATA
TRESHOLD LIMIT VALUE
EFFECTS OF OVEREXPOSURE
EMERGENCY AND FIRST AID PROCEDURES
STABILITY
SECTION VI
REACTIVITY DATA
100ppm
CONDITIONS TO AVOID
UNSTABLE
STABLE
X
INCOMPATABILITY (Materials to avoid)
HAZARDOUS DECOMPOSITION PRODUCTS
HAZARDOUS
POLYMERIZATION
MAY
OCCUR
X
CONDITIONS TO AVOID
WILL NOT
OCCUR
SECTION IX
SPECIAL
PRECAUTIONS
SECTION VIII - SPECIAL
PROTECTION INFORMATION
SECTION VII
SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Rinse with water
WASTE DISPOSAL METHOD
RESPIRATORY PROTECTION (Specific type)
VENTILATION
LOCAL EXHAUST
SPECIAL
MECHANICAL (General)
OTHER
PROTECTIVE GLOVES
EYE PROTECTION
OTHER PROTECTIVE EQUIPMENT
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING
Harmful if swallowed
Keep out of the reach of children
OTHER PRECAUTIONS
To avoid from oxidants
THE INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED ACCURATE.
HOWEVER, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE ACCURACY OF
THESE DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THEREOF.
VENDOR ASSUMES NO RESPONSABILITY FOR INJURY TO VENDEE OR THIRD PERSONS
PROXIMATELY CAUSED BY THE MATERIAL IF REASONABLE SAFETY PROCEDURES ARE NOT
ADHERED TO AS STIPULATED IN THE DATA SHEET. ADDITIONALLY, VENDOR ASSUMES NO
RESPONSABILITY FOR INJURY TO VENDEE OR THIRD PERSONS PROXIMATELY CAUSED BY
ABNORMAL USE OF THE MATERIAL EVEN REASONABLE SAFETY PROCEDURES ARE FOLLOWED. FUTHERMORE, VENDEE ASSUMES THE RISK IN HIS USE OF THE MATERIAL.
Downloaded From projector-manual.com Barco Manuals