Alliance Laundry Systems B-Series Installation manual

Programming
Washer-Extractors
Cabinet Freestanding
WE8 B-Series Microcomputer for Coin Models
Refer to Page 2 for Model Identification
NORMAL
WASH
ADD
BLEACH
HOT
WARM
NORMAL
PERM PRESS
RINSE
SPIN
PERM PRESS
WARM
COLD
QUICK WASH
QUICK WASH
START
DOOR
HOT
WARM
HEAVY SOIL
DELICATE
HOT
COLD
DOMESTIC MODELS
CHM4
CHM482R
95C
95C
60C
60C
40C
40C
30C
<
<
INTERNATIONAL MODELS
CHM488R
CHM488R
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.comlaundry.com
Part No. 9001999R4
July 2011
Table of
Contents
Introduction.........................................................................................
Model Identification .............................................................................
2
2
Safety Information..............................................................................
Explanation of Safety Messages...........................................................
Important Safety Instructions ...............................................................
Safety Decals ........................................................................................
Operator Safety.....................................................................................
3
3
3
5
6
Programming ......................................................................................
Power Up ..............................................................................................
Communications ...................................................................................
Entering Program Mode .......................................................................
Setup Mode...........................................................................................
Programming Vend Amount.................................................................
Programming Coin 1/Coin 2 Denomination.........................................
Programming Decimal Point Position ..................................................
Calibration Procedure ...........................................................................
Cycle Programming ..............................................................................
Rapid Advance......................................................................................
Test Cycle .............................................................................................
Abnormal Conditions............................................................................
Emergency Stop ...............................................................................
Restart after Power Interruption.......................................................
Door Will Not Lock .........................................................................
Door Open During Operation ..........................................................
Excessive Fill Time..........................................................................
Excessive Drain Time ......................................................................
Out of Balance .................................................................................
Door Will Not Unlock .....................................................................
Free Mode ........................................................................................
Cycle Charts
Domestic Coin Cycles ........................................................................
Cycle Charts
International Coin Cycles...................................................................
7
7
7
7
7
7
8
8
8
8
9
9
11
11
11
11
11
11
11
11
11
11
12
16
© Copyright 2011, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Introduction
Model Identification
Information in this manual is applicable to these
models:
2
NX18BVPA6
NX18BVPA7
NX18BVQA6
NX18BVQA7
NX18BVXA6
NX18BVXA7
NX18BVXM6
NX18BVXM7
SX018BVPA7
SX018BVQA7
SX018BVXA6
SX018BVXA7
SX018BVXM7
SX18BVPA7
SX18BVQA7
SX18BVXA7
SX18BVXM7
18
NX018BVPA7
NX018BVQA7
NX018BVXA6
NX018BVXA7
NX018BVXM7
NX30BVPA6
NX30BVPA7
NX30BVQA6
NX30BVQA7
NX30BVXA6
NX30BVXA7
NX30BVXM6
NX30BVXM7
SX030BVPA7
SX030BVQA7
SX030BVXA6
SX030BVXA7
SX030BVXM7
SX30BVPA7
SX30BVQA7
SX30BVXA7
SX30BVXM7
30
NX030BVPA7
NX030BVQA7
NX030BVXA6
NX030BVXA7
NX030BVXM7
33
SX33BVPA7
SX33BVQA7
SX33BVXA7
SX33BVXM7
40
SX40BVPA7
SX40BVQA7
SX40BVXA7
SX40BVXM7
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Safety Information
Explanation of Safety Messages
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
DANGER
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
Important Safety Instructions
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
1. Read all instructions before using the washer.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, drycleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
13. Use washer only for its intended purpose,
washing textiles.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
16. Install the washer according to the
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
20. If the supply cord is damaged, it must be replaced
by a special cord or assembly available from the
manufacturer or its service agent.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
25. Never operate the washer with any guards and/or
panels removed.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
instructions may result in conditions which can
produce bodily injury and/or property damage.
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
damage, and may void the warranty.
SW004
IMPORTANT: Ensure that the recommended
clearances for inspection and maintenance
are provided. Never allow the inspection and
maintenance space to be blocked.
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
SW025
WARNING
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
the pipe can be touched.
SW014
WARNING
Install the machine on a level floor of
sufficient strength. Failure to do so may
result in conditions which can produce
serious injury, death and/or property
damage.
W703
Safety Decals
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the
manufacturer immediately.
Use manufacturer-authorized spare parts to avoid
safety hazards.
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Safety Information
Operator Safety
Do not bypass any safety devices in the machine.
WARNING
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
Never operate the machine with a
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage.
SW039
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Programming
Power Up
Programming Vend Amount
During power up, the software version of the control
will display (i.e., “0009” or later) Next, the default
cycle vend, Perm Press Cold (domestic models) or 60c
Perm Press (international models) will display.
NOTE: This option selects the vend amount for
each cycle program (total of eight vend amounts,
one for each cycle).
Communications
Alliance Planner Software
The Alliance Planner Software is a program that
allows the user to pre-program customized cycle
formulas, vends, etc. for all WE-8 B-Control washerextractors in a facility. The information from the
software is downloaded into the laptop, where the user
is able to create and/or modify cycles. The cycle
information is stored on the laptop and then
downloaded into the washer-extractor.
NOTE: The machines are factory programmed
with basic cycles to make the units operational
without programming at installation.
Entering Program Mode
1. Open coin box
2. Locate rocker switch at top front inside coin
vault.
3. Press the switch end toward the front of the
machine. Cycles count (“----”) will display. This
count cannot be reset.
4. Press START (enter).
5. Display will show “PricE PrG1” and show the
current vend amount for cycle one. Refer to
Programming Vend Amount Section.
NOTE: Programming mode can be exited at any
time by returning the programming switch to run
mode.
NOTE: Program Mode can only be entered if a
cycle is not in process.
Setup Mode
Vend and coin amounts can be programmed using the
keypad or the Alliance Planner Software. All vend and
coin amount programming changes, whether through
the keypad or the Alliance Planner, MUST be made in
Program Mode. Refer to Entering Program Mode.
NOTE: For Free Mode, set vend to 0.
NOTE: Vend amounts are changed by using the up
(∧) arrow keypad or the down (∨) arrow keypad.
1. After entering program mode, display scrolls
“PriCE PrG1”, then shows the vend price for
cycle Program 1. Use up arrow keypad to
increase, or down arrow to decrease. If correct,
press START (enter) keypad to continue.
2. Displays “PrG2”, then shows the vend price for
cycle Program 2. Use up keypad to increase,
down keypad to decrease, or press START (enter)
keypad to continue.
3. Displays “PrG3”, then shows the vend price for
cycle Program 3. Use up keypad to increase,
down keypad to decrease, or press START (enter)
keypad to continue.
4. Displays “PrG4”, then shows the vend price for
cycle Program 4. Use up keypad to increase,
down keypad to decrease, or press START (enter)
keypad to continue.
5. Displays “PrG5”, then shows the vend price for
cycle Program 5. Use up keypad to increase,
down keypad to decrease, or press START (enter)
keypad to continue.
6. Displays “PrG6”, then shows the vend price for
cycle Program 6. Use up keypad to increase,
down keypad to decrease, or press START (enter)
keypad to continue.
7. Displays “PrG7”, then shows the vend price for
cycle Program 7. Use up keypad to increase,
down keypad to decrease, or press START (enter)
keypad to continue.
8. Displays “PrG8”, then shows the vend price for
cycle Program 8. Use up keypad to increase,
down keypad to decrease, or press START (enter)
keypad to continue.
NOTE: All changes followed by pressing START
(enter) will be stored.
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Programming
Programming Coin 1/Coin 2
Denomination
NOTE: This option allows the programmer to
designate the coin values to be used. (i.e., .25 = US
quarter, 1.00 Yen, etc…)
NOTE: Coin denomination amounts are changed
by using the up (∧) arrow keypad or the down (∨)
arrow keypad.
9. Displays “coIN 1”, then the coin 1 denomination
value. Use up keypad to increase, down keypad
to decrease, or press START (enter) keypad to
continue.
10. Displays “coIN 2”, then the coin 2 denomination
value (only for models with a dual drop coin
meter). Use up keypad to increase, down keypad
to decrease, or press START (enter) keypad to
continue.
Programming Decimal Point
Position
NOTE: This option selects the position of the
decimal point. It can be placed between the
leftmost pair of digits (i.e., 1.000), between the
middle pair of digits (i.e., 00.25), or between the
right most pair of digits (i.e., 000.1) in the display.
NOTE: Decimal point position is changed. Coin
denomination amounts are changed by using the up
(∧) arrow keypad or the down (∨) arrow keypad.
11. Display scrolls “dECIMAL”, then shows the four
digits with the decimal point located. Use up to
change the position, or press START (enter)
keypad to continue.
12. The calibration procedure begins after pressing
START (enter). Refer to Calibration Procedure
Section.
2. Control accelerates to the each of the spin speed
presets, showing “SPIn x” (“x” = spin speed
number 1, 2, etc.), then the RPM, maintaining
each briefly while showing RPM.
3. When complete, control allows machine to coast
to a stop, while display shows “COASt dOWN
PLEASE WAIT”.
4. Once machine has stopped, control unlocks door
and displays “done”. The door can be opened,
and the program switch returned to RUN
position.
Cycle Programming
The 8 cycle programs cannot be modified from the
keypad. Changing the factory cycle programs requires
a laptop computer, with Alliance Planner Software
V1.04 or later installed on the laptop. The laptop
connects to the machine using a serial port which is
accessed by opening the coin box. The PROGRAM
switch in the coin box on the machine must be in
PROGRAM mode before the cycle programs can be
read, written or downloaded using the laptop and
Alliance Planner Software.
Once the connection between the laptop computer and
machine is made, and the PROGRAM switch is in
program position, use the software to read, write,
modify or download cycles.
IMPORTANT: The machine selected in the
Alliance Planner software on the laptop MUST
match the machine it is connected to.
IMPORTANT: Any cycles which may exist above
cycle 9 on the laptop, using Alliance Planner file
will not be transferred to the washer (only cycles
1 - 9 will transfer).
Contact the factory for information regarding
“Alliance Planner” software.
Calibration Procedure
The calibration procedure immediately follows the end
of programming decimal point position. As soon as
START (enter) keypad is pressed after programming
the display decimal point position, the control locks
the door. If door is open, “Shut door” will display
until door is closed. Calibration procedure begins as
described in the following steps:
1. Display scrolls “dIStrIb SPEEd”, then machine
runs briefly at distribution speed, and the RPM
displays.
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Programming
Rapid Advance
Test Cycle
NOTE: This option allows the user to step forward
in the cycle during operation before the step is
complete. Rapid Advance is enabled by following
the steps below:
NOTE: The test cycle is a special cycle (cycle 9)
which will verify all major machine functions. To
run a test cycle, follow the steps below:
1. Turn off power to the machine.
2. Press and HOLD the (∧) and (*) keypads while
restoring power.
3. Display will show Advance.
4. Release keypads and advance is enabled.
5. Press START (enter) to select Rapid Advance.
6. Press START (enter) again to start the cycle
already in process.
7. Press the lower right keypad (∧) down arrow
symbol) to advance in the cycle.
1. Turn off power to machine.
2. Press and HOLD the (∧) and PERM PRESS/
WARM (domestic models) or 95C Synthetic
(international models) keypads while restoring
power.
3. Display will show “test”.
4. Press START (enter) to begin the test cycle.
NOTE: Rapid Advance is automatically enabled
for the test cycle and disabled at the end of the test
cycle.
NOTE: Advance is disabled at end of cycle.
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Programming
15
15
1
2
1
2
5
15
14
WASH
ADD
BLEACH
13
RINSE
12
SPIN
NORMAL
PERM PRESS
HOT
WARM
NORMAL
PERM PRESS
WARM
COLD
QUICK WASH
QUICK WASH
6
7
START
DOOR
HOT
11
HEAVY SOIL
5
15
8
WARM
DELICATE
14
13
12
95C
95C
60C
60C
40C
40C
6
7
8
11
30C
9
3
4
10
COLD
CHM482R
9
DOMESTIC MODELS
3
4
CHM488R
INTERNATIONAL MODELS
CHM482R
1
2
3
4
5
6
7
8
<
HOT
<
10
Cycle 1
Cycle 2
Cycle 3
Cycle 4/Up Edit
Cycle 5
Cycle 6
Cycle 7
Cycle 8/Down Edit
CHM488R
9
10
11
12
13
14
15
START (enter) Keypad
LED (not in use)
Door Step LED
Spin Step LED
Rinse Step LED
Add Bleach LED
Decimals for Pricing
Figure 1
NOTE: If the version of control in machine is
capable of reading temperature, pressing the
START (enter) keypad while a wash is running will
cause the display to show temperature and will
revert to minutes remaining after several seconds.
10
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Programming
Abnormal Conditions
Excessive Drain Time
Emergency Stop
The control gives a Drain alarm if the machine has not
emptied within the time limit programmed for the
drain step in the cycle. The display indicates ERROR
DRAIN, until machine drains. Otherwise, if the user
presses START (enter), control repeats drain step.
Pressing the red emergency stop button on the rear of
the machine will immediately stop the machine. If the
emergency stop button is not reset, machine will
initiate a safe stop routine releasing the door after
several minutes. If safety stop is reset during the first
several minutes option of selecting, resume cycle by
pressing START (enter) keypad.
Restart after Power Interruption
After power has been restored, press START (enter) to
resume cycle. If START (enter) is not pressed within
one minute, machine will initiate a safe stop routine
releasing the door and ending the cycle.
Door Will Not Lock
If the door handle has not been properly closed after
paying the vend and pressing START (enter), control
will not allow the cycle to start. Display will show
“Shut door” and the status LED “door” will light
prompting the user to close the door properly. Once
the door is closed properly, the LED will turn off and
the user should press START (enter) again. If this
continues, it indicates a problem, and a qualified
service technician should be consulted.
Out of Balance
If the machine goes out of balance, the machine will
attempt to balance the load with as many attempts as
programmed. After “__” attempts, the control aborts
the cycle and initiates the stop routine before the door
is opened leaving the load's water extraction at the
highest level achieved before shut down.
Door Will Not Unlock
If the door will not unlock, shut off power to gain
access to load. If this fault continues, it indicates a
problem, and a qualified service technician should be
consulted.
Free Mode
For set up information, refer to Programming Vend
Amount Section.
Door Open During Operation
If the control senses either a momentary or sustained
open door while the machine is operating in a wash
cycle, the control immediately attempts to halt rotation
of the cylinder. All outputs not required to effect rapid
halting of the cylinder rotation de-energize
immediately. The message “door” then displays as
long as the condition persists. Regardless of the
duration of the open door condition, once it is
recognized by the control, the control aborts the cycle
and goes to the stop routine even if the door is closed.
Excessive Fill Time
The control provides a Fill alarm whenever the water
level has not reached the programmed setting within
the time limit programmed for the cycle program step.
The display indicates “ERROR FILL” with an audible
beep, if the user does not press the START (enter)
keypad within 2 minutes, control aborts the cycle, and
continues to indicate the condition at the end of the
stop routine before the door is opened. Otherwise, if
the user presses START (enter) within 2 minutes the
control resumes the fill step.
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Programming
Cycle Charts
Domestic Coin Cycles
Cycle 01
Step
Normal Hot
Cycle 02
Min:sec
Step
Normal Warm
Min:sec
1
Hot Fill to Low Level
7:00
1
Warm Fill to Low Level
7:00
2
Supply 1, 2, 5
0:30
2
Supply 1, 2, 5
0:30
3
Wash 1 18/3 (32°F)
4:00
3
Wash 1 18/3 (32°F)
4:00
4
Drain 1
5:00
4
Drain 1
5:00
5
Cold Fill to High Level
7:00
5
Cold Fill to High Level
7:00
6
Wash 1 18/3 (32°F)
2:00
6
Wash 1 18/3 (32°F)
2:00
7
Drain 1
5:00
7
Drain 1
5:00
8
Cold Fill to Low Level
7:00
8
Cold Fill to Low Level
7:00
9
Wash 1 18/3 (32°F)
2:00
9
Wash 1 18/3 (32°F)
2:00
10
Drain 1
5:00
10
Drain 1
5:00
11
Cold Fill to Low Level
7:00
11
Cold Fill to Low Level
7:00
12
Supply 3
0:30
12
Supply 3
0:30
13
Wash 1 18/3 (32°F)
2:00
13
Wash 1 18/3 (32°F)
2:00
14
Drain 1
5:00
14
Drain 1
5:00
15
Spin 4
4:00
15
Spin 4
4:00
Cycle 03
Step
12
Quick Wash Hot
Min:sec
1
Hot Fill to Low Level
7:00
2
Supply 1, 2, 5
0:30
3
Wash 1 18/3 (32°F)
4:00
4
Drain 1
5:00
5
Cold Fill to High Level
7:00
6
Wash 1 18/3 (32°F)
2:00
7
Drain 1
5:00
8
Cold Fill to High Level
7:00
9
Supply 3
0:30
10
Wash 1 18/3 (32°F)
2:00
11
Drain 1
5:00
12
Spin 2
4:00
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Programming
Cycle 04
Step
Heavy Soil Hot
Cycle 05
Min:sec
Step
Perm Press Warm
Min:sec
1
Hot Fill to Low Level
7:00
1
Warm Fill to Low Level
7:00
2
Supply 1, 2, 5
0:30
2
Supply 1, 2, 5
0:30
3
Wash 1 18/3 (32°F)
6:00
3
Wash 1 18/3 (32°F)
4:00
4
Drain 1
5:00
4
Drain 1
5:00
5
Cold Fill to High Level
7:00
5
Cold Fill to High Level
7:00
6
Wash 1 18/3 (32°F)
3:00
6
Wash 1 18/3 (32°F)
2:00
7
Drain 1
5:00
7
Drain 1
5:00
8
Cold Fill to Low Level
7:00
8
Cold Fill to Low Level
7:00
9
Wash 1 18/3 (32°F)
2:00
9
Wash 1 18/3 (32°F)
2:00
10
Drain 1
5:00
10
Drain 1
5:00
11
Cold Fill to Low Level
7:00
11
Cold Fill to Low Level
7:00
12
Supply 3
0:30
12
Supply 3
0:30
13
Wash 1 18/3 (32°F)
2:00
13
Wash 1 18/3 (32°F)
2:00
14
Drain 1
5:00
14
Drain 1
5:00
15
Spin 2
4:00
15
Spin 1
3:00
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Programming
Cycle 07
Cycle 06
Step
14
Perm Press Cold
Min:sec
Step
Quick Wash Warm
Min:sec
1
Cold Fill to Low Level
7:00
1
Warm Fill to Low Level
7:00
2
Supply 1, 2, 5
0:30
2
Supply 1, 2, 5
0:30
3
Wash 1 18/3 (32°F)
4:00
3
Wash 1 18/3 (32°F)
4:00
4
Drain 1
5:00
4
Drain 1
5:00
5
Cold Fill to High Level
7:00
5
Cold Fill to High Level
7:00
6
Wash 1 18/3 (32°F)
2:00
6
Wash 1 18/3 (32°F)
2:00
7
Drain 1
5:00
7
Drain 1
5:00
8
Cold Fill to Low Level
7:00
8
Cold Fill to High Level
7:00
9
Wash 1 18/3 (32°F)
2:00
9
Supply 3
0:30
10
Drain 1
5:00
10
Wash 1 18/3 (32°F)
2:00
11
Cold Fill to Low Level
7:00
11
Drain 1
5:00
12
Supply 3
0:30
12
Spin 2
3:00
13
Wash 1 18/3 (32°F)
2:00
14
Drain 1
5:00
15
Spin 1
3:00
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Programming
Cycle 08
Step
Delicate Cold
Cycle 09
Min:sec
Step
Test Program
Min:sec
1
Cold Fill to Med Level
7:00
1
Cold Fill to Low Level
2:00
2
Supply 1, 2
0:30
2
Wash 3, no agitation (32°F)
0:30
3
Wash 2 3/27 (32°F)
4:00
3
Drain 1
5:00
4
Drain 1
5:00
4
Hot Fill to Med Level
2:00
5
Cold Fill to High Level
7:00
5
Wash 3, no agitation (32°F)
0:30
6
Wash 2 3/27 (32°F)
2:00
6
Drain 1
5:00
7
Drain 1
5:00
7
Warm Fill to High Level
2:00
8
Cold Fill to High Level
7:00
8
Wash 3, no agitation (32°F)
0:30
9
Supply 3
0:30
9
Drain 1
5:00
10
Wash 2 3/27 (32°F)
2:00
10
135°F Fill to Low Level
2:00
11
Drain 1
5:00
11
Heat (150°F)
1:00
12
Spin 1
2:00
12
Wash 1 18/3 (32°F)
0:30
13
Supply 1
0:10
14
Supply 2
0:10
15
Supply 3
0:10
16
Supply 5
0:10
17
Wash 1 18/3 (32°F)
0:30
18
Wash 2 3/27 (32°F)
0:30
19
Spin 1
2:00
20
Spin 2
2:00
21
Spin 3
2:00
22
Spin 4
2:00
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Programming
Cycle Charts
International Coin Cycles
Cycle 01
Step
16
Normal 95C
Cycle 02
Min:sec
Step
Normal 60C
Min:sec
1
Warm Fill to Low Level
7:00
1
Warm Fill to Low Level
7:00
2
Supply 1
0:30
2
Supply 1
0:30
3
Heat (40°C)
0:50
3
Heat (40°C)
0:50
4
Wash 1 18/3 (0°C)
2:00
4
Wash 1 18/3 (0°C)
2:00
5
Drain 1
5:00
5
Drain 1
5:00
6
Hot Fill to Low Level
7:00
6
Warm Fill to Low Level
7:00
7
Supply 1, 2
0:30
7
Supply 1, 2
0:30
8
Heat (95°C)
0:50
8
Heat (60°C)
0:50
9
Wash 1 18/3 (0°C)
6:00
9
Wash 1 18/3 (0°C)
6:00
10
Cold Fill to High Level
7:00
10
Cold Fill to High Level
7:00
11
Wash 1 18/3 (0°C)
2:00
11
Wash 1 18/3 (0°C)
2:00
12
Drain 1
5:00
12
Drain 1
5:00
13
Cold Fill to High Level
7:00
13
Cold Fill to High Level
7:00
14
Wash 1 18/3 (0°C)
2:00
14
Wash 1 18/3 (0°C)
2:00
15
Drain 1
5:00
15
Drain 1
5:00
16
Cold Fill to High level
7:00
16
Cold Fill to High level
7:00
17
Wash 1 18/3 (0°C)
2:00
17
Wash 1 18/3 (0°C)
2:00
18
Drain 1
5:00
18
Drain 1
5:00
19
Spin 1
1:00
19
Spin 1
1:00
20
Cold Fill to High Level
7:00
20
Cold Fill to High Level
7:00
21
Supply 3
0:30
21
Supply 3
0:30
22
Wash 1 18/3 (0°C)
3:00
22
Wash 1 18/3 (0°C)
3:00
23
Drain 1
5:00
23
Drain 1
5:00
24
Spin 4
5:00
24
Spin 4
5:00
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Programming
Cycle 03
Step
Normal 40C
Cycle 04
Min:sec
Step
Gentle Cold
Min:sec
1
Warm Fill to Low Level
7:00
1
Cold Fill to High Level
7:00
2
Supply 1
0:30
2
Supply 1, 2
0:30
3
Heat (40°C)
0:50
3
Wash 2 3/27 (0°C)
2:00
4
Wash 1 18/3 (0°C)
2:00
4
Drain 1
5:00
5
Drain 1
5:00
5
Cold Fill to High Level
7:00
6
Hot Fill to Low Level
7:00
6
Wash 2 3/27 (0°C)
2:00
7
Supply 1, 2
0:30
7
Drain 1
5:00
8
Heat (40°C)
0:50
8
Spin 1
2:00
9
Wash 1 18/3 (0°C)
6:00
9
Cold Fill to High Level
7:00
10
Cold Fill to High Level
7:00
10
Supply 3
0:30
11
Wash 1 18/3 (0°C)
2:00
11
Wash 2 3/27 (0°C)
3:00
12
Drain 1
5:00
12
Drain 1
5:00
13
Cold Fill to High Level
7:00
13
Spin 1
2:00
14
Wash 1 18/3 (0°C)
2:00
15
Drain 1
5:00
16
Cold Fill to High level
7:00
17
Wash 1 18/3 (0°C)
2:00
18
Drain 1
5:00
19
Spin 1
1:00
20
Cold Fill to High Level
7:00
21
Supply 3
0:30
22
Wash 1 18/3 (0°C)
3:00
23
Drain 1
5:00
24
Spin 4
5:00
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Programming
Cycle 05
Step
18
Perm Press 95C
Cycle 06
Min:sec
Step
Perm Press 60C
Min:sec
1
Warm Fill to Low Level
7:00
1
Warm Fill to Low Level
7:00
2
Supply 1
0:30
2
Supply 1
0:30
3
Heat (40°C)
0:50
3
Heat (40°C)
0:50
4
Wash 1 18/3 (0°C)
2:00
4
Wash 1 18/3 (0°C)
2:00
5
Drain 1
5:00
5
Drain 1
5:00
6
Hot Fill to Low Level
7:00
6
Warm Fill to Low Level
7:00
7
Supply 1, 2
0:30
7
Supply 1, 2
0:30
8
Heat (95°C)
0:50
8
Heat (60°C)
0:50
9
Wash 1 18/3 (0°C)
6:00
9
Wash 1 18/3 (0°C)
6:00
10
Cold Fill to High Level
7:00
10
Cold Fill to High Level
7:00
11
Wash 1 18/3 (0°C)
2:00
11
Wash 1 18/3 (0°C)
2:00
12
Drain 1
5:00
12
Drain 1
5:00
13
Cold Fill to High Level
7:00
13
Cold Fill to High Level
7:00
14
Wash 1 18/3 (0°C)
2:00
14
Wash 1 18/3 (0°C)
2:00
15
Drain 1
5:00
15
Drain 1
5:00
16
Cold Fill to High level
7:00
16
Cold Fill to High Level
7:00
17
Wash 1 18/3 (0°C)
2:00
17
Wash 1 18/3 (0°C)
2:00
18
Drain 1
5:00
18
Drain 1
5:00
19
Spin 1
1:00
19
Spin 1
1:00
20
Cold Fill to High Level
7:00
20
Cold Fill to High Level
7:00
21
Supply 3
0:30
21
Supply 3
0:30
22
Wash 1 18/3 (0°C)
3:00
22
Wash 1 18/3 (0°C)
3:00
23
Drain 1
5:00
23
Drain 1
5:00
24
Spin 1
3:00
24
Spin 1
3:00
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999
Programming
Cycle 07
Step
Perm Press 40C
Cycle 08
Min:sec
Step
Gentle 30C
Min:sec
1
Warm Fill to Low Level
7:00
1
Cold Fill to High Level
7:00
2
Supply 1
0:30
2
Supply 1
0:30
3
Heat (40°C)
0:50
3
Wash 2 3/27 (80°C)
2:00
4
Wash 2 3/27 (0°C)
2:00
4
Drain 1
5:00
5
Drain 1
5:00
5
Cold Fill to High Level
7:00
6
Hot Fill to Low Level
7:00
6
Supply 1, 2
0:30
7
Supply 1, 2
0:30
7
Heat (30°C)
0:50
8
Heat (40°C)
0:50
8
Wash 2 3/27 (0°C)
2:00
9
Wash 2 3/27 (0°C)
6:00
9
Drain 1
5:00
10
Cold Fill to High Level
7:00
10
Cold Fill to High Level
7:00
11
Wash 2 3/27 (0°C)
2:00
11
Wash 2 3/27 (0°C)
2:00
12
Drain 1
5:00
12
Drain 1
5:00
13
Cold Fill to High Level
7:00
13
Spin 1
1:00
14
Wash 2 3/27 (0°C)
2:00
14
Cold Fill to High Level
7:00
15
Drain 1
5:00
15
Supply 3
0:30
16
Cold Fill to High Level
7:00
16
Wash 2 3/27 (0°C)
2:00
17
Wash 2 3/27 (0°C)
2:00
17
Drain 1
5:00
18
Drain 1
5:00
18
Spin 1
2:00
19
Spin 1
1:00
20
Cold Fill to High Level
7:00
21
Supply 3
0:30
22
Wash 2 3/27 (0°C)
3:00
23
Drain 1
5:00
24
Spin 1
3:00
9001999
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Programming
Cycle 09
Step
20
Test Program
Min:sec
1
Cold Fill to Low Level
2:00
2
Wash 3, no agitation (0°C)
0:30
3
Drain 1
5:00
4
Hot Fill to Med Level
2:00
5
Wash 3, no agitation (0°C)
0:30
6
Drain 1
5:00
7
Warm Fill to High Level
2:00
8
Wash 3, no agitation (0°C)
0:30
9
Drain 1
5:00
10
57°C Fill to Low Level
2:00
11
Heat (65°C)
1:00
12
Wash 1 18/3 (0°C)
0:30
13
Supply 1
0:10
14
Supply 2
0:10
15
Supply 3
0:10
16
Supply 5
0:10
17
Wash 1 18/3 (0°C)
0:30
18
Wash 2 3/27 (0°C)
0:30
19
Spin 1
2:00
20
Spin 2
2:00
21
Spin 3
2:00
22
Spin 4
2:00
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9001999