Mazda 6 2006-2007

INSTALLATION INSTRUCTIONS FOR PART 99-7507
APPLICATIONS
Mazda 6 2006-2007
99-7507
KIT FEATURES
• DIN Head Unit Provision
• ISO DIN Head Unit Provision
KIT COMPONENTS
A) Radio/Climate Control Housing Assembly • B) ISO Brackets • C) ISO Trim Plate • D) Harnesses
A
B
C
D
TOOLS REQUIRED:
Phillips Screwdriver • Small Flat Blade Screwdriver • Socket Wrench
1-800-221-0932
© COPYRIGHT 2007-2009
www.metraonline.com
METRA ELECTRONICS CORPORATION
99-7507
TABLE OF CONTENTS
Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Electronic Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Manual Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8
Electronic Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Manual Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Felt Tape Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Display Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Final Wiring and Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . .11,12
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills
by enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com
or call 800-354-6782 for more information
and take steps toward a better tomorrow.
99-7507
DASH DISASSEMBLY
MAZDA 6 2006-2007
Electronic Climate Control
A
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Unscrew the shift knob counter
clockwise to remove. (Figure A)
3
Unclip and remove the cup
holder/parking brake cover and
shifter cover as one unit. (Figure B)
B
4
Remove (2) Phillips screws from the
bottom of the radio/climate control
panel. (Figure C)
5
Open glove box, squeeze sides
together and let open fully then
remove (1) 10 MM bolt from the side
of the radio bracket. (Figure D)
C
D
INSIDE
GLOVE BOX
1
99-7507
DASH DISASSEMBLY
MAZDA 6 2006-2007
Electronic Climate Control
E
6
Unsnap and remove radio/climate
control panel including climate control vents at the top. (Figure E)
7
Remove (4) Phillips screws securing
vents to radio/climate control panel
to remove. (Figure F)
8
Remove (8) Phillips screws securing
the electronic climate control to the
radio/climate control panel to
remove. (Figure G)
F
G
Rear of Radio/Climate Control Panel
Rear of Electronic Climate Control
2
99-7507
DASH DISASSEMBLY
MAZDA 6 2006-2007
Manual Climate Control
A
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Unscrew the shift knob counter
clockwise to remove. (Figure A)
3
Unclip and remove the cup
holder/parking brake cover and
shifter cover as one unit. (Figure B)
4
Remove (2) Phillips screws from the
bottom of the radio/climate control
panel. (Figure C)
5
Pull the climate control knobs off
and remove (2) Phillips screws from
behind knobs. (Figure D)
B
D
C
A/C
3
99-7507
DASH DISASSEMBLY
MAZDA 6 2006-2007
Manual Climate Control
E
6
Open glove box, squeeze sides
together and let open fully then
remove (1) 10 MM bolt from the side
of the radio bracket. (Figure E)
7
Unsnap and remove radio/climate
control panel including climate control vents at the top. (Figure F)
8
INSIDE
GLOVE BOX
Remove (4) Phillips screws securing
vents to radio/climate control panel
to remove. (Figure G)
F
Remove the (2) small Phillips screws
securing the light bulb boards on
each side of the backlight dispersion
bar. Note: Notice how they are positioned in the backlight dispersion bar
as they will be placed in the 99-7507
the same way. (Figure H)
9
H
G
4
99-7507
DASH DISASSEMBLY
MAZDA 6 2006-2007
Manual Climate Control
I
10 Remove (4) Phillips screws securing
backlight dispersion bar and knob
trim bezels. (Figure I)
11 Push the bottom edges of the knob
trim bezels from the front side to the
back and slide both pieces out as
one unit. (Figure J)
J
5
99-7507
KIT ASSEMBLY
MAZDA 6 2006-2007
Electronic Climate Control
A
1
Clip the climate control knob outer
trim ring panel into the 99-7507
housing. (Figure A)
2
Align the screw holes in the climate
control and the radio housing panel
then push the climate control onto
the radio housing panel. (Figure B)
3
Secure the climate control with the
factory hardware removed in step 8
of the dash disassembly for
electronic climate control cars.
3
Unclip and remove the small oval
cover plate at the bottom center of
the factory radio and insert into the
99-7507 radio housing. (Figure C)
B
REAR VIEW OF ELECTRONIC CLIMATE CONTROL
D
Note: The 16 position to 16 position
harness supplied with the 99-7507
will NOT be used in vehicles with
electronic climate controls.
(Figure D)
C
NOTE: This 16 to 16 position harness
is NOT USED with ELECTRONIC
CLIMATE CONTROL vehicles.
6
99-7507
KIT ASSEMBLY
MAZDA 6 2006-2007
Manual Climate Control
1
Put the climate control knob outer
trim panel and the backlight dispersion bar together and clip into the
radio housing panel as one unit.
Note: You may have to push down
slightly on the middle of the unit to
ease in positioning it into the kit.
(Figure A, B, C )
2
Secure the unit with the factory
hardware removed in step 10 of the
manual climate control dash disassembly.
3
Secure the light bulb boards on each
side of the backlight dispersion bar
using the factory hardware removed
in step 9 in manual climate control
dash disassembly. (Figure D )
4
Unclip and remove the small oval
cover plate at the bottom center of
the factory radio and insert into the
99-7507 radio housing. (Figure E)
A
B
ASSEMBLED
C
D
INSTALLED
E
Note: The 16 position to
16 position harness
supplied with the 99-7507
WILL BE USED in vehicles
with MANUAL CLIMATE
CONTROLS. (Figure F)
7
F
99-7507
KIT ASSEMBLY
DIN HEAD UNIT PROVISION
A
1
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
2
Slide the aftermarket head unit into
the DIN cage until secure. (Figure B)
B
3
Snap the Trim plate into the Radio
Housing. (Figure B)
ISO DIN HEAD UNIT PROVISION
A
1
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
2
Slide the head unit into the radio
opening until the side clips engage.
(Figure B)
3
Snap the Trim plate into the Radio
Housing. (Figure B)
B
8
99-7507
FELT TAPE APPLICATION
Apply To
Rear Of
Both Sides
Note: Due to differences in factory tolerances you may need to apply the provided felt tape to the
edge of the 99-7507 radio housing to relieve backlight bleed through.
1. Looking at edge of radio housing apply felt tape to inner edge (toward back of kit). If it is positioned to closely to the outer edge you may be able to see it once it is in the dash.
9
99-7507
DISPLAY CUSTOMIZATION
CLO
CK
SET
DIM
MER
AMB
1. Press and hold the AMB button on the factory display for 5 seconds then release the button. The
first character will be highlighted. Settings will begin with the first character location. Use the AMB
button to select the desired character then wait. The next character will be highlighted. Press and
release to set that character, and keep going until the text is to your liking. There are 10 available
character locations.
2. Once the desired text is entered press and hold the AMB button for greater than 5 seconds then
release and the display will read “Text Saved.”
10
95-7507
FINAL ASSEMBLY
FINAL WIRING and ASSEMBLY
A
B
C
A)
Strip wire ends back 1/2"
B)
Twist ends together
C)
Solder
D)
Tape
D
1
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray/ Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
11
95-7507
FINAL ASSEMBLY
FINAL WIRING and ASSEMBLY
2
Plug the 5 way connector (supplied with the 99-7507) into location 1 on the back of the
99-7507 housing (see diagram).
3
On manual climate control vehicles only, plug the 16 way connector (supplied with the
99-7507) into location 3 on the back of the 99-7507 housing (see diagram). Automatic climate
control vehicles will not use this harness.
4
Plug the 2 way connector (supplied with the 99-7507) into location 4 on the back of the
99-7507 housing (see diagram).
5
Re-connect the negative battery
terminal and test the unit for
proper operation.
6
Reassemble radio and dash
assemblies in reverse order of
disassembly.
4
1
3
2
Note: The connector “2” is not used in this
application.
12
99-7507
NOTES
13
INST997507
1-800-221-0932
REV. 07/16/09
© COPYRIGHT 2007-2009
www.metraonline.com
METRA ELECTRONICS CORPORATION
INST99-7507