Mitsubishi PAC-YG60MCA Technical information

Controls
A Comprehensive Range
of Control Options
Air Conditioning Commercial Heating
Domestic Heating Photovoltaics
The Importance
of Control
The need for control is paramount in order to optimise the performance
of any air conditioning system and minimise its running costs and the
emissions generated. Mitsubishi Electric offer a wide range of control
options designed to do just this.
Operating an air conditioning system without the right control
can prove costly. It’s therefore important to ensure that every
system is correctly specified to the degree of control it
requires. Mitsubishi Electric have a wide range of controls
available ‘off-the-shelf’ and where needed, individual control
systems can be specifically designed to suit.
Good controls will benefit any application, large or small.
Air conditioning products need to react to a variety of factors:
different room sizes, usage and staff levels, changes in the
climate, electronic equipment and lighting etc.
The ability to monitor the energy consumption and operation
of systems is also vital. It is often said that you cannot manage
what you are not measuring. Our control systems will enable
simple measuring and monitoring of energy consumption and
running costs to ensure operation is maintained.
Controlled
Performance
In accordance with the requirements of
Part L2 in the Building Regulations, our control
systems provide the optimum control available,
combined with the most efficient
use of energy.
A Degree of Difference
When an air conditioning system is not properly controlled, it
will not run as efficiently as it should. For every degree that the
system deviates from the required temperature, energy costs
can rise by up to 5%. Specify one of the many control options
from Mitsubishi Electric to ensure air conditioning works as
intended, whilst giving the optimum amount of control.
The Simpler the Better
With the array of comprehensive control systems available
from Mitsubishi Electric, it becomes simple to design and install
air conditioning systems. From a simple hand held controller to
an AG150 system - you are in control.
So whatever the application, optimum control of air conditioning
systems is essential and will result in a constant, comfortable
environment, which in turn is both energy and cost efficient.
Page 266
Page 267
Which Controls Product for Which Application?
Which Controls Product for Which Function?
It is really important to match the right control with the right application. From a hotel to a retail
application, the solution will be different and the right control must be applied.
Application
Small
Medium
Application
Large
Notes
MELCOTEL
A hotel usually requires interfacing with a key
card system and window contact. The Melcotel
has been designed to do just this for up to 250
City Multi indoor units. The Melcotel can also
work without a key card system
TM
Hotel
AG150
MELCOTEL
TM
TM
TM
Office
Retail
Leisure
Education
PAR-30MAA
PAR-F27MEA
IO Interface
PAR-30MAA
PAR-F27MEA
Mini M2M
PAR-30MAA
PAR-F27MEA
Mini M2M
AG150
Mini M2M
AG150
Maxi M2M
AG150
Maxi M2M
TG2000
Maxi M2M
AG150
TG2000
AG150
TG2000
In an office application there is usually someone
managing the air conditioning, so the interface
needs to be simple to use. The user friendly
AG150 touch screen is one option, as well as
the TG2000 PC graphical user interface
Retail shops are usually managed by head offices
or facility management companies, so it is key to
have remote monitoring of the air conditioning,
but also any building services which can also be
connected to the M2M interfaces
In small applications the M2M platform can be
a solution, as well as the AG150 touch screen
or the TG2000 software package for
larger applications
In small applications the M2M platform can be
a solution, as well as the AG150 touch screen
or the TG2000 software package for
larger applications
Low
Cost and Features
High
Notes
Option 1
Option 2
Option 3
Option 4
Option 5
Remote On/Off
or fire alarm
PAC-SA89TA
TCB1
IO Interface
AT50
AG150 and
PAC-YG10HA
On/Off remote controller
button lock except TCB1
Monitor run
and faults
PAC-SA88HA
IO Interface
AT50
AG150 and
PAC-YG10HA
-
Relays or power supply
may be required
Window
interlocking
PAC-SA89TA
TCB1
-
-
-
Controller will be centrally
controlled when window
opened
Setpoint limit
PAR-30MAA
PAR-F27MEA
AT50
AG150
AG150 and
TG2000
Available in Heat, Cool
and Auto modes
Weekly timer
PAR-30MAA
AT50
AG150
AG150 and
TG2000
M2M
Setpoint, On/Off can
be reset
Night set back
TCB1
AT50
AG150
AG150 and
TG2000
M2M
TCB1 requires thermostat,
timeswitch, 12v power supply
Energy
monitoring
AG150 and
AG150 and
PAC-CN32WHMC-UK PAC-YG60MCA
TG2000,
AG150 and
PAC-YG60MCA
Mini M2M
Maxi M2M
Different options for each
choice. Meters required
Load shedding
AG150 and
PAC-YG60MCA
Mini M2M
Maxi M2M
-
-
Energy meters required
Trend logging
AG150 and
TG2000
Mini M2M
Maxi M2M
-
-
CSV data available
on a spreadsheet
Night mode
PAC-SA89TA
AG150
-
-
-
PAC-SA89TA requires a
third party timer
Ambient tracking
AG150 and
PAC-YG63MCA
Mini M2M
Maxi M2M
-
-
PT100 sensor required
Key card interlock
for hotel
AG150,
MELCOTEL
AG150-Interlock and PAC-SA89TA
and PAC-SA89TA
-
-
-
Volt free contact for
key card normally open
Window sensor
interlock for hotel
MELCOTEL
and PAC-SA89TA
-
-
-
-
Volt free contact for key
card normally closed
2 setpoints (1 for
cool and 1 for heat)
IO Interface
Mini M2M
Maxi M2M
-
-
For instance, 19ºC Heat
and 23ºC Cool. Fan only
in between
Duty / Standby
PAR-30MAA
PANEL_RS_SMS -
-
-
Backup, rotate, join in and
high temperature function
A/C faults
via SMS
Micro M2M
-
-
-
-
SIM card not supplied
Optimised start
AG150
-
-
-
-
-
Mini BEMS
Mini M2M
Maxi M2M
-
-
-
-
TM
TM
NOTE: The PAC-SA89TA is also known as a 3 wire adaptor and the PAC-SA88HA is also known as a 5 wire adaptor
DISCLAIMER: These options are for guidance only
Page 268
Page 269
A Wide Range of
Control Options
The need for control is paramount in order
to optimise the performance of any air
conditioning system and minimise its running
costs. Mitsubishi Electric offer a wide range
of control options designed to do just this.
With the array of comprehensive control
systems available from Mitsubishi Electric,
it becomes simple to design and install air
conditioning systems. From a simple hand
held controller to an AG150 system you are in control.
Page 270
Contents
272
Remote Controllers
290
TG2000 WAN Software (Wide Area Network)
273
AT50 Controller, Centralised Controller
291
TG2000, Screenshots
274
Interfaces
292
BEMS BACnet Interface (BAC-IP/50)
275
IO Interface
293
BEMS BACnet Interface (BAC-HD150)
276
AG150 Controller, Centralised Controller
294
BEMS BACnet Mr Slim Interface (BAC-A/50)
277
AT50/AG150 Controller, Touch Screen Examples
295
BEMS LonWorks Interface (LMAP)
278
AG150 Expansion Controller (PAC-YG50ECA)
296
BEMS Modbus Interface (MOD-IP/50)
279
GB50ADA Controller, Centralised Controller
297
BEMS Modbus Mr Slim Interface (A32M)
280
AG150/GB50 Controller, Web Screenshots
298
BEMS Modbus Splits Interface (A1M)
281
PAR-21PC Desktop Remote Controller
299
BEMS KNX-EIB Interfaces (KNX-EIB-IP-15/100)
282
AG150/GB50 Third Party Equipment Interfaces
300
BEMS KNX-EIB Splits Interface (KNX-EIB-A-1)
283
AG150/GB50 Melcotel Hotel Interface,
with key card system
301
BEMS Trend Interface (Trend IQ3 Excite)
302
284
AG150/GB50 Melcotel Hotel Interface,
without key card system
M2M - Machine 2 Machine
Interface (Maxi M2M-IP/50)
303
285
AG150/GB50 Melcotel Hotel Interface,
with M2M
M2M - Machine 2 Machine
Splits Interface (Mini M2M-A/16)
304
286
TG2000 Software, PC Based Software Package
M2M - Machine 2 Machine
Splits Interface (Micro M2M-SMS-A/08)
287
TG2000 Software with Energy Monitoring
305
M2M - Machine 2 Machine Web Screenshots
288
Energy Monitoring
306
Run Standby Panel (PANEL_RS_SMS)
289
TG2000 Software with Third Party Equipment
307
Split-System A2M Interfaces
TM
TM
TM
®
®
®
®
Page 271
AT50 Controller
Our air conditioning systems are supported by a multitude of remote controllers. Each remote controller type, whilst
being able to support the general control and monitoring functions for a group of indoor units, can also offer other unique
operational features.
PAC-SE51CRA
BS-51COV-B
PS-51COV-B
PB-51COV-B
PAR-30MAA
PAR-F27MEA
PAR-FL32MA
Technical Information
Remote Controllers
FUNCTION
DESCRIPTION
ON/OFF
Run and Stop operation for a single group
MODE SELECTION
Switches between Cool/Dry/Auto/Fan/Heat.
Operation mode will vary depending on the
indoor unit. Auto mode is available with only
R2 and WR2 systems
PAC-YT51CRB PAC-SE51CRA
PAR-30MAA
Display
Operation
Display
Operation
Display
Operation
Display
Operation
Display
Sets the groups temperature control.
Cool/Dry: 19-30°C
Heat: 17-28°C
Auto: 19-28°C
FAN SPEED SETTING
4 speed - Lo-Mi1-Mi2-Hi
2 speed - Lo-Hi
SETPOINT LIMIT
Limit the setpoint range
AIRFLOW DIRECTION
INDEPENDENT VANE
CONTROL
AT50
Air Flow angles:100º-80º-60º-40º
and auto swing
Only available with PLA-RP-BA, PLFY-P-VBM-E
and PLFY-P-VCM-E
Daily
TIMER OPERATION
ON/OFF time can be set.
PERMIT / PROHIBIT
FUNCTION
Run/Stop, Temperature Setting, Mode Selection
and Filter Reset functions can be prohibited
via a higher level system controller
INDOOR RETURN
AIR TEMPERATURE
Measures the intake temperature of
the master unit within the group
ERROR INDICATION
Displays a 4 digit code and the affected unit address
TEST RUN FUNCTION
Allows each unit within the group
to operate in test mode
VENTILATION
INTERLOCK
Allows the group to be interlocked
with a heat recovery Lossnay unit
OPTIONAL COVER
Brushed Stainless Steel
Polished Stainless Steel
Polished Brass
CONTACT NUMBER
UNDER FAULT
CONDITIONS
Displays under fault condition, the fault code
of the unit with its address and the contact
number to call
EASY MAINTENANCE
WITH MR SLIM
Able to monitor info about the compressor
(running current, running time, On/Off time).
Also able to monitor sensors: h-exh, OU outlet,
OU temp, IU inlet, IU h-exh and filter usage
BACKLIGHT DISPLAY
Backlight display. Displays current time
BUTTON LOCK
Able to lock all controller buttons, or
all controller buttons except On/Off
Daily
Daily
Daily
PAC-SC51KUA
Technical Information
Weekly
Weekly
Reset the unit setpoint after a period of time
SILENT MODE
Activate with scheduling the silent mode
on the outdoor unit
NIGHT SET BACK
Maintain a min and max temperature
RUN / STANDBY WITH
MR SLIM
Able to switch over two systems every week.
If one fails, the other system starts. If the
temperature is too high, the two systems start.
COMPATIBILITY
Compatible with:
AT50 Controller
FUNCTION
DESCRIPTION
TOUCH SCREEN
5” QVGA touch screen
MAX No. OF INDOOR UNITS
Up to 50 indoor units can be connected
ON/OFF
Run and Stop operation for a single group
MODE SELECTION
Switches between Cool/Dry/Auto/Fan/Heat. Operation Mode will vary depending on the indoor unit.
Auto mode is available with only R2 and WR2 systems
TEMPERATURE SETTING
Sets the groups temperature control. Cool/Dry: 19-30°C, Heat:17-28°C, Auto: 19-28°C
TIMER OPERATION
Annual or weekly. Night set back option available allowing the setpoint to be set to 12ºC
AIR FLOW DIRECTION
Air Flow angles:100º-80º-60º-40º and auto swing
FAN SPEED SETTING
4 speed: Lo-Mi1-Mi2-Hi, 2 speed: Lo-Hi
PERMIT/PROHIBIT FUNCTION
Individual prohibit operations for each remote controller function (Run/Stop,Temperature Setting,
Mode Selection and Filter Reset) can be activated
INDOOR RETURN AIR TEMPERATURE
Displays the measured intake temperature from each group
ENERGY SAVING
Page 272
PAR-FL32MA
Operation
TEMPERATURE
SETTING
DIMENSIONS - mm (WxDxH)
PAR-F27MEA
ERROR INDICATION
Displays a 4 digit code and the affected unit address. An error log is held
TEST RUN FUNCTION
Allows each unit within the group to operate in test mode
VENTILATION INTERLOCK
Allows the group to be interlocked with a heat recovery Lossnay unit
FIRE ALARM
Units will be switched off and the remote controller will be locked under fire alarm condition
NIGHT SET BACK
During unoccupied hours the system works in a reduced state. For instance, an unoccupied room in heating mode will keep
the temperature of the room between 16 and 19°C. In cooling the temperature will range between 24 and 26°C
POWER SUPPLY
Power supply 240VAC 0.5A (PAC-SC51KUA required)
COMPATIBILITY
City Multi or Mr Slim via PAC-SF81MA or M Series via MAC-399IF
DIMENSIONS - mm
Mr Slim or
M Series (via MAC-397IF)
City Multi, Mr Slim
(via PAC-SF81MA)
or M Series
(via MAC-399IF)
City Multi, Mr Slim or
M Series (via MAC-397IF)
City Multi, Mr Slim
(via PAC-SF81MA)
or M Series
(via MAC-399IF)
City Multi (via PAR-FA32MA)
or Mr Slim (via PAR-FA32MA)
120x41x70
120x41x70
120x19x120
130x19x120
157x18x57
(WxDxH)
180x30x120
Page 273
Remote Controllers / AT50 Controller
PAC-YT51CRB
The new AT50 centralised controller is a low cost version of the very popular AG150 touch screen controller.
The AT50 offers the main AG150 functionality, with a very simple and easy to use 5 inch touch screen.
Controls Range
Remote Controllers
IO Interface
The new IO interface has been developed to allow third party systems, for instance BEMS companies, to easily control
and monitor our air conditioning systems using simple volt free contacts and 0 to 10VDC signals. By working very
closely with our main retail clients we have added some beneficial energy saving features, whilst still offering an
acceptable level of control for retail applications. To avoid wasting energy the IO interface can also be used to
interlock third party heating systems to our air conditioning.
A range of newly created interfaces are now available for use when connecting to third party controllers.
PAC-SA89TA
IO Interface
TCB1
PAC-SA88HA
Controls Range
Interfaces
Technical Information
IO Interface
TCB1
PAC-SA88HA
Technical Information
Interfaces
FUNCTION
DESCRIPTION
PAC-SA89TA
Control
ON/OFF
BUT CENTRALLY
CONTROLLED
ON/OFF control. Remote controller
ON/OFF button deactivated
ON/OFF BUT
NOT CENTRALLY
CONTROLLED
ON/OFF control. Remote controller
ON/OFF button activated
TEMPERATURE SETTINGS
Sets the groups temperature control.
Cool/Dry: 19-30°C
Heat: 17-28°C
Auto: 19-28°C
Monitor
PAC-SA88HA
Control
Monitor
(12VDC)
(12VDC)
ERROR INDICATION
(12VDC)
Interface compatible with:
DIMENSIONS - mm
(WxDxH)
NOTE: VFC: Volt free contact.
PAC-SA89TA is also known as a 3 wire adaptor.
PAC-SA88HA is also known as a 5 wire adaptor.
Monitor
(VFC)
RUN INDICATION
COMPATIBILITY
TCB1
Control
Mr Slim
City Multi
Mr Slim
City Multi
Mr Slim
City Multi
80x45x80
DESCRIPTION
INPUTS / OUTPUTS
IO INTERFACE
UNIT
Max No. of indoor units
-
1 or 16*1
ON/OFF
Run and Stop operation for a single group
Input
Volt Free Contact
LOCK
Run/Stop, Temperature Setting, Mode Selection and Filter
Reset functions can be prohibited
Input
Volt Free Contact
ENERGY SAVE
Energy Save can be activated. 2 options are available
Input
Volt Free Contact
TEMPERATURE SETTING
Sets the groups temperature control
Input
0 to 10VDC
MODE
Switches between Cool/Dry/Auto/Fan/Heat. Operation mode
will vary depending on the indoor unit. Auto mode is available
with only R2 and WR2 systems
Input
0 to 10VDC
FAN SPEED
4 speed - Lo-Mi1-Mi2-Hi
2 speed - Lo-Hi
Input
0 to 10VDC
RUN STATUS
-
Output
Volt Free Contact
FAULT
-
Output
Volt Free Contact
HEAT / COOL
Activates when unit is in heating or cooling mode
Output
Volt Free Contact
THERMO
Activates when room temperature is 2ºC away from setpoint
Output
Volt Free Contact
COMPATIBILITY
Mr Slim and M Series
-
-
DIMENSIONS - mm (WxDxH)
85x32x138
-
-
Energy Saving Features
MODE 1
MODE 2
The energy saving mode 1 sets the indoor unit to Auto mode
whenever a momentary signal is applied to the ‘Energy Save’
input or whenever the on/off state is changed from OFF to ON.
The unit will operate in AUTO for 0.5, 1 or 2hours and then
revert back to fan only.
The energy saving mode 2 sets two setpoints for the indoor
unit, one for heating and one for cooling. In between the
indoor unit will be running in fan only mode.
The timer can be reset using the Energy Save input.
OFF
AUTO
09.00
OFF
AUTO
09.00
Page 274
11.00
11.00
FAN
13.00
FAN
15.00
AUTO
OFF
17.00
FAN
13.00
15.00
17.00
Active via push button
19.00
OFF
19.00
25
24
23
22
21
20
19
18
COOLING MODE
FAN ONLY MODE
HEATING MODE
*1 The IO Interface can control up to 16 indoor units when the fault output is not used. When the fault output is used only one indoor unit can be controlled.
Page 275
Interfaces / IO Interface
PAC-SA89TA
FUNCTION
AT50/AG150 Controller Touch Screen Examples
Touch Screen Centralised Controller with WebServer Capabilities
AT50 Home Screen 1
AG150 Home Screen 1
AT50 Home Screen 2
AG150 Home Screen 2
AT50 Home Screen 3
AG150 Home Screen 3
AT50 Indoor Unit Settings
AG150 Indoor Unit Settings
AT50 Scheduling
AG150 Scheduling
The AG150 Mitsubishi Electric centralised controller offers a large 9 inch touch screen display with easy control of up to 50
indoor units. The AG150 can calculate the energy used for each system. The refrigerant status check function can be
activated regularly (in conjuction with the new YJM-A City Multi range) and an Internet connection with SSL security
is also available to monitor and control the AG150 remotely and receive Email under fault conditions.
ETHERNET
M-NET
AG150
PAC-SC51KUA
Viewed using Microsoft® Internet Explorer
Technical Information
Controls Range
AG150 Controller
DESCRIPTION
TOUCH SCREEN
Wide high resolution 9” touch screen
OPERATION PLATFORM
CPU 1000 Mhz, 512 MB RAM, 6GB or more. Internal LAN 10/100 MBps running Windows Professional 2000
service pack 4 or Windows Professional XP service pack 2 or Windows Vista or Windows 7
MAX No. OF INDOOR UNITS
Up to 50 indoor units can be connected or 150 using an expansion controller (PAC-YG50ECA)
ON/OFF
Run and Stop operation for a single group
MODE SELECTION
Switches between Cool/Dry/Auto/Fan/Heat. Operation Mode will vary depending on the indoor unit.
Auto mode is available with only R2 and WR2 systems
TEMPERATURE SETTING
Sets the groups temperature control. Cool/Dry: 19-30°C, Heat:17-28°C, Auto: 19-28°C
TIMER OPERATION
Annual or weekly. Night set back available allowing the setpoint to be set to 12ºC
AIR FLOW DIRECTION
Air Flow angles:100º-80º-60º-40º and auto swing
FAN SPEED SETTING
4 speed: Lo-Mi1-Mi2-Hi, 2 speed: Lo-Hi
PERMIT/PROHIBIT FUNCTION
Individual prohibit operations for each remote controller function (Run/Stop,Temperature Setting,
Mode Selection and Filter Reset) can be activated
INDOOR RETURN AIR TEMPERATURE
Displays the measured intake temperature from each group
ERROR INDICATION
Displays a 4 digit code and the affected unit address including the description of the error. An error log is held
TEST RUN FUNCTION
Allows each unit within the group to operate in test mode
VENTILATION INTERLOCK
Allows the group to be interlocked with a heat recovery Lossnay unit
OPTIMISED START
The equipment is started only as early as required to bring the building to a setpoint at the time it will be occupied.
Running in an optimal state helps reduce energy usage.
AUTOMATIC SETPOINT ADJUSTMENT
The AG150 will change the setpoint depending of the outdoor temperature. PAC-YG63MCA and a PT100 sensor are
required (PT100 sensor not supplied by MEUK). This function is only available in COOL mode
AUTO LOCK
The AG150 screen can be password protected. When the screen goes to standby and when the AG150 restarts,
a username and password will be required
NIGHT SET BACK
During unoccupied hours the system works in a reduced state. For instance, an unoccupied room in heating mode will keep
the temperature of the room between 16 and 19°C. In cooling the temperature will range between 24 and 26°C
AutoCAD DRAWING
A floor plan of the building in auto-cad format can be uploaded. For the facilities department it makes viewing and adjusting settings easier
WEB LOGIN
Administrator able to allow specific function access to guest
WEB SETPOINT LIMIT
Reduce the setpoint band of each individual unit (e.g. 23ºC to 25ºC)
WEB AUTO CHANGEOVER
Automatically switch heat pump outdoor unit to cooling or heating mode depending on the requirements
WEB INITIAL SETTING
Commission the AG150 from the web pages
WEB REFRIGERANT STATUS CHECK
Activate refrigerant volume checking function on Modular City Multi systems
WEB-INTERLOCK
The AG150 can interlock indoor unit input and output together. For instance, this function could be used for Hotel
applications, if card in, set unit to ON, AUTO 21ºC and if card out, set the unit to night set back. This function could also
be set in conjunction with PIR sensor in meeting rooms
WEB-LOAD SHEDDING
Activate energy saving mode when energy consumption is too high
EXTERNAL INPUT/OUTPUT
Hardwired connections are available for :
Inputs:
Outputs:
Level Signal-Batch Start/Stop, Batch Emergency Stop
Start/Stop Status, Error/Normal Status
FIRE ALARM
Units will be switched off and the remote controller will be locked under fire alarm condition via a PAC-YG10HA
POWER SUPPLY
Power supply 240VAC 0.5A (PAC-SC51KUA required)
COMPATIBILITY
DIMENSIONS - mm
City Multi or Mr Slim via PAC-SF81MA or M Series via MAC-399IF
(WxDxH)
300x62x175
AG150 Software Options - Pin Code Activation
DEMONSTRATION
Web monitoring, Email, Annual scheduling
AG150 - VRC Virtual remote controllers
AG150 - Basic
AG150 - Energy Energy monitoring, energy saving, load shedding AG150 - Interlock Interlocking function
Visit wwwL1.mitsubishielectric.co.jp/
wink_doc/wink_files/acr/menu/ag150
Page 276
AG150 Controller /
AT50/AG150 Controller Touch Screen Examples
AG150 Controller
FUNCTION
Page 277
PAC-YG50ECA
AG150 Expansion Controller
Centralised Controller with WebServer Capabilities
The PAC-YG50ECA expansion controller allows the AG150 to monitor and control up to 150 indoors units.
The GB50 has been developed to access all your control functions from the comfort of your own PC,
without the need for a controller keypad or LCD display and at a very competitive price.
Controls Range
GB50ADA Controller
M-NET
AG150
ETHERNET
GB50ADA
ETHERNET
PAC-YG50ECA
PAC-YG50ECA
Viewed using Microsoft® Internet Explorer
Technical Information
PAC-SC51KUA
FUNCTION
DESCRIPTION
OPERATION PLATFORM
CPU 1000 Mhz, 512MB RAM, 6GB or more. Internal LAN 10/100 MBps running Windows Professional 2000
service pack 4 or Windows Professional XP service pack 2 or Windows Vista or Windows 7
MAX No. OF INDOOR UNITS
Up to 50 indoor units can be connected
ON/OFF
Run and Stop operation for a single group
MODE SELECTION
Switches between Cool/Dry/Auto/Fan/Heat. Operation Mode will vary depending on the indoor unit.
Auto mode is available with only R2 and WR2 systems
TEMPERATURE SETTING
Sets the groups temperature control. Cool/Dry: 19-30°C, Heat:17-28°C, Auto: 19-28°C
FAN SPEED SETTING
4 speed: Lo-Mi1-Mi2-Hi, 2 speed: Lo-Hi
AIR FLOW DIRECTION
Air Flow angles:100º-80º-60º-40º and auto swing
TIMER OPERATION
Annual or weekly. Night set back option available allowing the setpoint to be set down to 12ºC
PERMIT/PROHIBIT FUNCTION
Individual prohibit operations for each remote controller function (Run/Stop,Temperature Setting,
Mode Selection and Filter Reset) can be activated
INDOOR RETURN AIR TEMPERATURE
Displays the measured intake temperature from each group
PAC-YG50ECA
HUB
Technical Information
PAC-YG50ECA
NUMBER OF INDOOR UNITS
NUMBER OF AG150 REQUIRED
1
0 to 50
Allows the group to be interlocked with a heat recovery Lossnay unit
WEB LOGIN
Administrator able to allow specific function access to guest
0
WEB SETPOINT LIMIT
Reduce the setpoint band of each individual unit (e.g. 23ºC to 25ºC)
2
101 to 150
1
3
PAC-YG50ECA
FUNCTION
DESCRIPTION
AG150 / PAC-YG50ECA CONNECTION
Ethernet. Ethernet hub and network cables required and not supplied by MEUK
POWER SUPPLY
240VAC 3.2A
250x97x266
Allows each unit within the group to operate in test mode
VENTILATION INTERLOCK
1
(WxDxH)
Displays a 4 digit code and the affected unit address. An error log is held showing the last 64 date stamped alarms
TEST RUN FUNCTION
NUMBER OF PAC-YG50ECA REQUIRED
51 to 100
DIMENSIONS - mm
ERROR INDICATION
WEB AUTO CHANGEOVER
Automatically switch heat pump outdoor unit to cooling or heating mode depending on the requirements
WEB INITIAL SETTING
Commission the GB50 from the web pages
WEB REFRIGERANT STATUS CHECK
Activate refrigerant volume checking function on Modular City Multi systems
WEB-INTERLOCK
The GB50 can interlock indoor unit input and output together. For instance, this function could be used for Hotel
applications, if card in, set unit to ON, AUTO 21ºC and if card out, set the unit to night set back. This function could
also be set in conjunction with PIR sensor in meeting rooms
WEB-LOAD SHEDDING
Activate energy saving mode when energy consumption is too high
EXTERNAL INPUT/OUTPUT
Hardwired connections are available for :
FIRE ALARM
Units will be switched off and the remote controller will be locked under fire alarm condition via a PAC-YG10HA
POWER SUPPLY
Power supply 240VAC 3.2A
COMPATIBILITY
DIMENSIONS - mm
Inputs:
Level Signal-Batch Start/Stop, Batch Emergency Stop
Outputs: Start/Stop Status, Error/Normal Status
City Multi or Mr Slim via PAC-SF81MA or M Series via MAC-399IF
(WxDxH)
250x97x266
GB50 Software Options - Pin Code Activation
G50
G50
G50
G50
Page 278
- EC
- ES
- PC
- VRC
Energy Charge
Energy Saving Capability
Peak Cut Control
Virtual Remote Controllers
Page 279
PAC-YG50ECA / GB50ADA Controller
GB50ADA Controller
Login
Monitor Air Conditioning - Overview
PAR-21PC
Desktop Remote Controller
More and more customers are using the AG150/GB50 controllers directly from their computers, so Mitsubishi
Electric has launched a new, even simpler alternative which presents the customer with what looks like a standard
remote controller interface - on their PC desktop. Called the PAR-21PC, the new application can also be minimised
in the Desktop Toolbar, just like other Windows applications, so that the customer can have immediate control
with just one click of the mouse.
Access to the web pages is secured using a customised
username and password.
The first screen allows you to monitor all the units connected to the
AG150/GB50. Each icon displays On/Off, Faults and timer On/Off.
Monitor Air Conditioning - Block view
Remote Controller Settings
M-NET
*NOTE 1
Controls Range
AG150/GB50 Controller Web Screenshots
ETHERNET
PAC-SC51KUA
Each area of the building can be displayed with information
about On/Off, Setpoint, Mode and Temperature.
Daily, Weekly and Annual Scheduling
(AS PIN code)
Click on any icons in the Monitor View page to access the
remote controller. Lossnay units can also be controlled.
Buttons on the local controllers may be locked
(On/Off, Mode, Setpoint, Filter Reset).
Monitor Fault Codes
PAR-21PC Desktop Remote Controller
Scheduling may be set from the web pages.
A night set back operation is available (Heat, 12ºC).
Standard on the AG150/GB50.
Faults with the unit address can be displayed under
fault conditions. Email status can also be shown.
Multiple Users (VRC PIN code)
Multiple Users (VRC PIN code)
If the AG150/GB50 is connected to an office LAN, the staff
will then be able to access the web pages. With VRC each
member of staff will have their own username and password.
Installation costs will be reduced as no wall remote
controllers will need to be purchased and installed.
FUNCTION
DESCRIPTION
OPERATION PLATFORM
CPU 1000 Mhz, 512 MB RAM, 6GB or more. Internal LAN 10/100 MBps running Windows
Professional 2000 service pack 4 or Windows Professional XP service pack 2
MAX No. OF INDOOR UNITS
Up to 16 indoor units within a group
ON/OFF
Run and Stop operation for a single group
MODE SELECTION
Switches between Cool/Dry/Auto/Fan/Heat. Operation Mode will vary depending
on the indoor unit. Auto mode is available with only R2 and WR2 systems
TEMPERATURE SETTING
Sets the groups temperature control. Cool/Dry: 19-30°C, Heat:17-28°C, Auto: 19-28°C
FAN SPEED SETTING
4 speed: Lo-Mi1-Mi2-Hi, 2 speed: Lo-Hi
AIR FLOW DIRECTION
Air Flow angles:100º-80º-60º-40º and auto swing
CLOCK DISPLAY
Displays the time on the desktop controller
INDOOR RETURN AIR TEMPERATURE
Displays the measured intake temperature from each group
ERROR INDICATION
Displays a 4 digit code and the affected unit address.
TIMER OPERATION
Weekly. Maximum of 3 time sequences with 3 Start/Stop times per day for all groups can be allocated
COMPATABILITY
AG150 and GB50
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Icons available to suit model type installed
Page 280
Page 281
AG150/GB50 Controller Web Screenshots /
PAR-21PC Desktop RemaoteController
Technical Information
AG150/GB50 Melcotel Hotel Interface
with Key Card System
The new third party equipment interfaces allow the user to monitor and control third party equipment from the
AG150/GB50 web pages.
ETHERNET
*NOTE 1
PAC-YG66DCA
The MelcotelTM hotel interface allows a hotel (for example) to have more accurate control over its air conditioning.
The MelcotelTM works in conjunction with the key card system installed in each bedroom in many hotels. When
the room is occupied, the MelcotelTM will switch ON the unit and reset the air conditioning to predetermined
settings (for instance AUTO, 21ºC). When the room is unoccupied, the MelcotelTM will monitor the temperature
in the room. If the temperature is too low or too high, the MelcotelTM will restart the unit. The MelcotelTM also
offers temperature adjustment facility based on the outside temperature and window open control, that allows
the air conditioning to be switched off and controlled centrally when a window is opened. All of these functions
provide a higher level of control and therefore more energy saving and a reduction in running costs.
PAC-YG63MCA
M-NET
EQUIPMENT 1
EQUIPMENT 2
SENSOR 1
Controls Range
AG150/GB50
Third Party Equipment Interfaces
TM
SENSOR 2
AG150
Technical Information
ETHERNET
Third Party Interfaces
PAC-SC51KUA
PAC-YG63MCA
2 x Digital
2 x Analogue
MAX No. OF OUTPUTS
-
2 x Digital
-
MAX No. OF EQUIPMENT
-
POWER SUPPLY
Power supply required
MONITOR
2
-
24VDC
24VDC
From AG150/GB50 web pages
or TG2000
Run / Faults
Temperature / Humidity
CONTROL
From AG150/GB50 web pages
or TG2000
On/Off
-
SIGNAL
Signal required to monitor
and control equipment
Volt free contact
Temperature 4-20mA / 1-5V / 0-10V / Pt100
Humidity 4-20mA / 1-5V / 0-10V
DIMENSIONS - mm
(WxDxH)
-
General Equipment
200x45x120
200x45x120
Temperature / Humidity
USB
Melcotel
Key Window
Card Control
Key Window
Card Control
Key Window
Card Control
TM
Technical Information
MELCOTEL
TM
FUNCTION
DESCRIPTION
MAX No. OF INDOOR UNITS
Up to 250 indoor units
TIME TO SWITCH ON
<30s
ON/OFF
Run and Stop operation for a single group
MODE SELECTION
Switches between Cool/Dry/Auto/Fan/Heat. Operation Mode will vary depending on the indoor unit.
Auto mode is available with only R2 and WR2 systems
TEMPERATURE SETTING
Sets the groups temperature control. Cool/Dry: 19-30°C, Heat:17-28°C, Auto: 19-28°C
OCCUPIED ROOM SETTING
Configurable. ON, AUTO, 21ºC (Factory setting)
UNOCCUPIED ROOM SETTING
Third party equipment can be monitored and controlled
from the web pages.
Temperature and humidity can be monitored.
Trend Logging
Temperature / Humidity Limit
Temperature and humidity can be recorded and displayed.
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
NOTE 2: Temperature Sensors and Humidity Sensors not supplied by MEUK
Page 282
Limit (high and low) can be set to trigger alarms via email.
If the temperature is below 16ºC the MelcotelTM restarts
the unit to ON, HEAT, 19ºC and stops the unit when the
temperature has reached 18ºC (Factory setting)
If the temperature is above 26ºC the MelcotelTM
restarts the unit to ON, COOL, 21ºC and stops
the unit when the temperature has reached
24ºC (Factory setting)
SEASONS
Up to 4 seasons can be set-up to allow different occupied and unoccupied settings (Setpoint and mode)
OPTIONAL WINDOW CONTACT
If a window sensor is wired to the indoor unit, the MelcotelTM will automatically switch OFF the indoor unit
when the window is opened
AUTOMATIC SETPOINT
The MelcotelTM will offset the occupied setpoint depending on the temperature outside (outdoor sensor supplied)
ADJUSTMENT NIGHT TIME OFFSET
During the night the MelcotelTM can offset the setpoint or just switch OFF the unit
INDOOR UNIT CONNECTION
The key card and the window contact is connected back locally to CN32. PAC-SA89TA required for each indoor unit
SOFTWARE
The MelcotelTM Configuration Manager allows the installer to set-up the interface using a USB cable. The MelcotelTM Live Status
allows the user to monitor all the different values, for instance, Setpoint, Mode, Key Card IN or OUT, Window Contact etc
FIRE ALARM
Units will be switched off and the remote controller will be locked under fire alarm condition
POWER SUPPLY
240 VAC 2A
COMPATIBILITY
GB50 and AG150, but City Multi only
DIMENSIONS - mm (WxDxH)
300x70x350
DEMONSTRATION
Visit www.melcotel.co.uk for more details
Page 283
TM
PAC-YG66DCA
-
Melcotel Hotel Interface with Key Card System
DESCRIPTION
MAX No. OF INPUTS
AG150/GB50 Third Party Equipment Interfaces /
FUNCTION
The MelcotelTM controller allows a hotel (for example) to have more accurate control over its air conditioning. When the
unit has been switched ON by a user, the room is deemed as occupied and the MelcotelTM resets the air conditioning to
predetermined settings (for instance AUTO, 21ºC). After a preset time, the MelcotelTM will switch OFF the unit automatically.
When the room is unoccupied, the MelcotelTM will monitor the temperature in the room. If the temperature is too low or
too high, the MelcotelTM will restart the unit. The MelcotelTM also offers temperature adjustment facility based on the outside
temperature and window open control, that allows the air conditioning to be switched off and controlled centrally when a
window is opened. All of these functions provide a higher level of control and therefore more energy saving and a
reduction in running costs.
AG150/GB50 Melcotel Hotel Interface
with Machine 2 Machine
TM
The MelcotelTM hotel interface can be connected to the Mini M2M Machine 2 Machine interface to allow
remote monitoring of the air conditioning, but also the window contact and the key card system.
Mini M2M-A/16
M-NET
MEUK
M2M
SERVER
GPRS
Melcotel
TM
Melcotel
TM
Controls Range
AG150/GB50 Melcotel Hotel Interface
without Key Card System
TM
AG150
ETHERNET
PAC-SC51KUA
USB
Mini M2M-A/16
Window
Control
Window
Control
Window
Control
Melcotel
TM
Technical Information
TM
MELCOTEL
TM
FUNCTION
DESCRIPTION
MAX No. OF INDOOR UNITS
Up to 250 indoor units
FUNCTION
TIME TO SWITCH ON
<30s
MAX No. OF INDOOR UNITS: UP TO 250
ON/OFF
Run and Stop operation for a single group
ON/OFF
MODE SELECTION
Switches between Cool/Dry/Auto/Fan/Heat. Operation Mode will vary depending on the indoor unit.
Auto mode is available with only R2 and WR2 systems
TEMPERATURE SETTING
Sets the groups temperature control. Cool/Dry: 19-30°C, Heat:17-28°C, Auto: 19-28°C
OCCUPIED ROOM SETTING
Configurable. ON, AUTO, 21ºC (Factory setting)
MODE
ROOM TEMPERATURE
SET TEMPERATURE
SET BACK
KEY CARD
UNOCCUPIED ROOM SETTING
WINDOW SENSOR
EXTERNAL TEMPERATURE
If the temperature is above 26ºC the MelcotelTM restarts
the unit to ON, COOL, 21ºC and stops the unit when
the temperature has reached 24ºC (Factory setting)
SEASONS
Up to 4 seasons can be set-up to allow different occupied and unoccupied settings (Setpoint and mode)
OPTIONAL WINDOW CONTACT
If a window sensor is wired to the indoor unit, the MelcotelTM will automatically switch OFF the indoor unit
when the window is opened
AUTOMATIC SETPOINT
The MelcotelTM will offset the occupied setpoint depending on the temperature outside (outdoor sensor supplied)
AUTO SWITCH OFF
6 Off times can be preset to regularly switch OFF the indoor unit
ADJUSTMENT NIGHT TIME OFFSET
During the night the MelcotelTM can offset the setpoint or just switch OFF the unit
INDOOR UNIT CONNECTION
The window contact is connected back locally to CN32. PAC-SA89TA required for each indoor unit
SOFTWARE
The MelcotelTM Configuration Manager allows the installer to set-up the interface using a USB cable. The MelcotelTM
Live Status allows the user to monitor all the different values, for instance, Setpoint, Mode, Window Contact etc
FIRE ALARM
Units will be switched off and the remote controller will be locked under fire alarm condition
POWER SUPPLY
240 VAC 2A
COMPATIBILITY
GB50 and AG150, but City Multi only
DIMENSIONS - mm (WxDxH)
300x70x350
DEMONSTRATION
Visit www.melcotel.co.uk for more details
Page 284
TM
If the temperature is below 16ºC the MelcotelTM restarts
the unit to ON, HEAT, 19ºC and stops the unit when
the temperature has reached 18ºC (Factory setting)
DEMONSTRATION
Visit www.melcotel.co.uk for more details
Page 285
TM
Melcotel Hotel Interface without Key Card System /
Melcotel Hotel Interface with M2M
MELCOTEL
Technical Information
TG2000 Software with Energy Monitoring
PC Based Software Package
PC Based Software Package
The TG2000 centralised PC based graphical software package allows the operator to control and monitor up to a
maximum of 2000 indoor units. This software has been designed to connect directly to an air conditioning system via the
AG150/GB50 controller, allowing the operator the required functionality to control and monitor the complete
air conditioning system from a central location.
The TG2000 centralised PC based graphical software package allows the operator to control and monitor up
to a maximum of 2000 indoor units. This software has been designed to connect directly to an air conditioning
system via the AG150/GB50 controller, allowing the operator all the required functionality to control and
monitor the complete air conditioning system from a central location. In addition to providing a centralised
control facility, the TG2000 allows complete energy consumption data to be logged with user definable billing
groups and electrical tariffs for billing purposes.
M-NET
M-NET
*NOTE 1
*NOTE 1
Controls Range
TG2000 Software
ETHERNET
ETHERNET
PAC-YG60MCA
PAC-SC51KUA
PAC-SC51KUA
METER 1
METER 2
METER 3
METER 4
Technical Information
Technical Information
TG2000 PC Based software that works in conjunction with AG150/GB50 Controller
FUNCTION
DESCRIPTION
OPERATING PLATFORM
CPU 1000 Mhz, 512 MB RAM, 6GB or more. Internal LAN 10/100 MBps running Windows Professional 2000
service pack 4 or Windows Professional XP service pack 2 or Windows Vista or Windows 7
MAX No. OF INDOOR UNITS
2000 Indoor units, 50 indoor units per AG150/GB50
OPERATIONAL SECTIONS
The software package is split into two distinctive areas, System and Controls setting. System Setting: Password
protected, System Configuration and group/block organisation, printer setting. Controls Setting: Normal Operation,
monitoring and control functions as described below. The software allows individual indoor units to be allocated
to logical groups, represented within user definable graphics screens, allocated during the system configuration
FUNCTION
DESCRIPTION
OPERATING PLATFORM
CPU 1000 Mhz, 512 MB RAM, 6GB or more. Internal LAN 10/100 MBps running Windows Professional 2000 service pack 4
or Windows Professional XP service pack 2 or Windows Vista or Windows 7
ON/OFF
Indicates the On/Off status of each group within the selected graphical screen or entire building
MAX No. OF INDOOR UNITS
2000 Indoor units, 50 indoor units per AG150/GB50
OPERATION MODE
Indicates the operational mode (Cool, Heat, Fan, Dry, Auto) for each group on the selected graphical screen
OPERATIONAL SECTIONS
The software package is split into two distinctive areas, System and Controls setting. System Setting: Password
protected, System Configuration and group/block organisation, printer setting. Controls Setting: Normal Operation,
monitoring and control functions as described below. The software allows individual indoor units to be allocated
to logical groups, represented within user definable graphics screens, allocated during the system configuration
SET TEMPERATURE
Displays the set temperature for each group on the selected graphical screen.
Also able to limit the set point range in both heating and cooling mode
AIR SPEED
Displays the current fan speed setting for each group on the selected graphical screen
ON/OFF
Indicates the On/Off status of each group within the selected graphical screen or entire building
Indicates the operational mode (Cool, Heat, Fan, Dry, Auto) for each group on the selected graphical screen
REMOTE CONTROLLER
PROHIBIT/PERMIT
Displays the current prohibit/permit status for each groups remote controller on the selected graphical screen
OPERATION MODE
SET TEMPERATURE
Displays the set temperature for each group on the selected graphical screen.
Also able to limit the set point range in both heating and cooling mode
ABNORMALITY (FAULT) MONITORING
AIR SPEED
Displays the current fan speed setting for each group on the selected graphical screen
Individual indoor unit fault monitoring is recorded within the fault log for both viewing and printing.
Fault monitoring can also be viewed via the fault log for all units associated with a particular graphical screen
or the entire building. Faults can also be tracked and printed using date of failure, date of recovery and error code
REMOTE CONTROLLER
PROHIBIT/PERMIT
Displays the current prohibit/permit status for each groups remote controller on the selected graphical screen
ROOM TEMPERATURE MONITORING
Displays the return air temperature of the master indoor unit within a group
SCHEDULED ON/OFF
On/Off schedules can be set for each group, each graphical screen or the entire building
ABNORMALITY (FAULT) MONITORING
Individual indoor unit fault monitoring is recorded within the fault log for both viewing and printing.
Fault monitoring can also be viewed via the fault log for all units associated with a particular graphical screen
or the entire building. Faults can also be tracked and printed using date of failure, date of recovery and error code
ENERGY CHARGING
Able to create or email bills for individual indoor units, groups of indoor units or a complete system (Optional) via the PAC-YG60MCA
WEB REFRIGERANT STATUS CHECK
Activate refrigerant volume checking function on Modular City Multi systems
ENERGY CHARGING
Able to create bills for individual indoor units, groups of indoor units or a complete system (Optional)
via the PAC-YG60MCA
ROOM TEMPERATURE MONITORING
Displays the return air temperature of the master indoor unit within a group
SCHEDULED ON/OFF
On/Off schedules can be set for each group, each graphical screen or the entire building
ENERGY SAVE CONTROL
ENERGY SAVE CONTROL
Individual indoor unit, group of indoor units or a complete system can be controlled. There are various energy
saving options available (Optional)
Individual indoor unit, group of indoor units or a complete system can be controlled.
There are various energy saving options available (Optional)
LOAD SHEDDING
Activate energy saving mode when energy consumption is too high
TREND LOGGING
Able to log: Return air temperature, setpoint, mode, On/Off, power consumption by group or by indoor unit,
watt-hour meter and then email to customer
TREND LOGGING
Able to log: Return air temperature, setpoint, mode, On/Off, power consumption by group or by indoor unit,
watt-hour meter and then email to customer
GRAPHICAL SCREENS
The complete system configurations can be allocated between multiple screens. Each screen can display a
bitmap image representing the area of the building or floor where the units or groups are physically located
GRAPHICAL SCREENS
The complete system configurations can be allocated between multiple screens. Each screen can display
a bitmap image representing the area of the building or floor where the units or groups are physically located
EMAIL
The following information may be sent regularly and automatically via email: energy monitoring data, energy saving data,
trend logging data (temperatures etc) and fault code history
EMAIL
The following information may be sent regularly and automatically via email: energy monitoring data,
energy saving data, trend logging data (temperatures etc) and fault code history
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Page 286
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
NOTE 2: Energy Meters not supplied by MEUK
Page 287
TG2000 Software /
TG2000 Software with Energy Monitoring
TG2000 Software with Energy Monitoring
Energy monitoring is key to comply with Part L2 regulations. Some time ago we introduced the PAC-YG60MCA MNET
interfaces, which can be connected anywhere on our MNET network and will monitor up to 4 pulse meters. These interfaces
make installation easier, more cost effective and are shown in option A below.
This year, all of our City Multi outdoor units now have a direct connection to pulse meters. This means that the pulse meter can
be connected to the outdoor unit directly, negating the need for interfaces, panels and a power supply and therefore reducing the
installation cost significantly. This is shown in option B below.
Option A:
TG2000 Software
with Third Party Equipment
PC Based Software Package
The TG2000 centralised PC based graphical software package allows the operator to control and monitor up to a
maximum of 2000 indoor units. This software has been designed to connect directly to an air conditioning system
via the AG150/GB50 controller, allowing the operator all the required functionality to control and monitor the
complete air conditioning system from a central location. In addition to providing a centralised control facility,
the TG2000 allows you to monitor and control third party equipment.
M-NET
M-NET
*NOTE 1
Controls Range
Energy Monitoring
*NOTE 1
ETHERNET
PAC-YG60MCA
ETHERNET
PAC-SC51KUA
PAC-SC51KUA
PAC-YG66DCA
METER 1
METER 2
METER 3
PAC-YG63MCA
METER 4
Option B:
EQUIPMENT 1
EQUIPMENT 2
SENSOR 1
SENSOR 2
Technical Information
M-NET
*NOTE 1
DESCRIPTION
OPERATING PLATFORM
CPU 1000 Mhz, 512 MB RAM, 6GB or more. Internal LAN 10/100 MBps running Windows Professional
2000 service pack 4 or Windows Professional XP service pack 2 or Windows Vista or Windows 7
MAX No. OF INDOOR UNITS
2000 Indoor units, 50 indoor units per AG150/GB50
OPERATIONAL SECTIONS
The software package is split into two distinctive areas, System and Controls setting. System Setting: Password
protected, System Configuration and group/block organisation, printer setting. Controls Setting: Normal Operation,
monitoring and control functions as described below. The software allows individual indoor units to be allocated
to logical groups, represented within user definable graphics screens, allocated during the system configuration
ON/OFF
Indicates the On/Off status of each group within the selected graphical screen or entire building
OPERATION MODE
Indicates the operational mode (Cool, Heat, Fan, Dry, Auto) for each group on the selected graphical screen
SET TEMPERATURE
Displays the set temperature for each group on the selected graphical screen.
Also able to limit the set point range in both heating and cooling mode
AIR SPEED
Displays the current fan speed setting for each group on the selected graphical screen
REMOTE CONTROLLER
PROHIBIT/PERMIT
Displays the current prohibit/permit status for each groups remote controller on the selected graphical screen
ABNORMALITY (FAULT) MONITORING
Individual indoor unit fault monitoring is recorded within the fault log for both viewing and printing.
Fault monitoring can also be viewed via the fault log for all units associated with a particular graphical screen
or the entire building. Faults can also be tracked and printed using date of failure, date of recovery and error code
ROOM TEMPERATURE MONITORING
Displays the return air temperature of the master indoor unit within a group
SCHEDULED ON/OFF
On/Off schedules can be set for each group, each graphical screen or the entire building
ENERGY SAVE CONTROL
Individual indoor unit, group of indoor units or a complete system can be controlled.
There are various energy saving options available (Optional)
TREND LOGGING
Able to log: Return air temperature, setpoint, mode, On/Off, power consumption by group
or by indoor unit, watt-hour meter and then email to customer
GRAPHICAL SCREENS
The complete system configurations can be allocated between multiple screens. Each screen can display
a bitmap image representing the area of the building or floor where the units or groups are physically located
ETHERNET
PAC-YG60MCA
PAC-SC51KUA
METER 1
Technical Information
Pulse Meter Direct Connection to City Multi Outdoor Unit
FUNCTION
PRODUCT REQUIRED
DESCRIPTION
OUTDOOR kW
AG150, AG150-Basic
Energy Meters
The energy consumption of the outdoor can be monitored using
the AG150 Webpages
INDOOR kW
AG150, AG150-Basic
AG150-Energy, TG2000
Energy Meters
The energy consumption of the indoor unit can be estimated using the
TG2000 software package. The software package will also allow the end
user to generate bills with multiple tariffs
Product Required
PAC-SA89TA
Cable required to connect the pulse meter to the outdoor unit
PAC-CN32WHMC-UK
Jumper to activate the outdoor pulse input
THIRD PARTY EQUIPMENT MONITOR
Monitor general equipment Run and Faults via the PAC-YG66DCA interface and Temperature and Humidity via the PAC-YG63MCA
THIRD PARTY EQUIPMENT CONTROL
Control general equipment On/Off via the PAC-YG66DCA
EMAIL
The following information may be sent regularly and automatically via email: energy monitoring data,
energy saving data, trend logging data (temperatures etc) and fault code history
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
NOTE 2: Temperature and Humidity Sensors not supplied by MEUK
Page 288
Page 289
Energy Monitoring /
TG2000 Software with Third Party Equipment
TG2000 Software with Third Party Equipment
FUNCTION
PC Based Software Package used to monitor and control multiple sites
TG2000
Controls Range
TG2000 WAN (Wide Area Network) Software
Screenshots
Display Whole
Display Block
The 2000 indoor units status may be shown
on one screen.
Block may be set for each area. Settings may be
changed by one click of the mouse for each area.
Display Floor
Remote Controller Settings
AutoCAD drawing may be imported to
TG2000 to display floor screens.
Click on any icons in the floor view to access the remote
controller settings. Buttons on the local controllers may
be locked (On/Off, Mode, Setpoint, Filter reset).
Daily, Weekly and Annual Scheduling
Monitor Fault Codes
Scheduling may be set from the TG2000. A night
set back operation is available (HEAT, 12ºC).
Faults with the unit address can be displayed under
fault conditions.
Energy Monitoring (AG150 Energy PIN code)
Energy Saving (AG150 Energy PIN code)
TG2000 in conjunction with energy meters can monitor
the energy consumption for each outdoor unit, indoor unit
or area. The indoor unit run hours can also be displayed.
TG2000 offers different energy saving options
including load shedding.
The TG2000 WAN centralised PC based graphical software package allows the operator to control and monitor
up to a maximum of 1000 sites. Utilising the companies Wide Area Network, the complete (geographically distributed)
air conditioning asset base can be controlled and monitored from a centralised location.
PAC-YG66DCA
WAN
PAC-YG63MCA
SITE 1
(i.e. MANCHESTER)
*NOTE 1
EQUIPMENT 1
EQUIPMENT 2
SENSOR 1
PAC-YG66DCA
SENSOR 2
PAC-YG63MCA
SITE 999
(i.e. BIRMINGHAM)
*NOTE 1
EQUIPMENT 1
EQUIPMENT 2
SENSOR 1
SENSOR 2
Technical Information
DESCRIPTION
OPERATING PLATFORM
CPU 1000 Mhz, 512 MB RAM, 6GB or more. Internal LAN 10/100 MBps running Windows Professional 2000
service pack 4 or Windows Professional XP service pack 2 or Windows Vista or Windows 7
MAX No. OF SITES
1000
MAX No. OF INDOOR UNITS PER SITE
2000 Indoor units, 50 indoor units per AG150/GB50 (per site)
OPERATIONAL SECTIONS
The software package is split into two distinctive areas, System and Controls setting. System Setting: Password
protected, System Configuration and group/block organisation, printer setting. Controls Setting: Normal Operation,
monitoring and control functions as described below. The software allows individual indoor units to be allocated
to logical groups, represented within user definable graphics screens, allocated during the system configuration
ON/OFF
Indicates the On/Off status of each group within the selected graphical screen or entire building
OPERATION MODE
Indicates the operational mode (Cool, Heat, Fan, Dry, Auto) for each group on the selected graphical screen
SET TEMPERATURE
Displays the set temperature for each group on the selected graphical screen.
Also able to limit the set point range in both heating and cooling mode
AIR SPEED
Displays the current fan speed setting for each group on the selected graphical screen
REMOTE CONTROLLER
PROHIBIT/PERMIT
Displays the current prohibit/permit status for each groups remote controller on the selected graphical screen
ABNORMALITY (FAULT) MONITORING
Individual indoor unit fault monitoring is recorded within the fault log for both viewing and printing.
Fault monitoring can also be viewed via the fault log for all units associated with a particular graphical screen or
the entire building. Faults can also be tracked and printed using date of failure, date of recovery and error code
ROOM TEMPERATURE MONITORING
Displays the return air temperature of the master indoor unit within a group
SCHEDULED ON/OFF
On/Off schedules can be set for each group, each graphical screen or the entire building
GRAPHICAL SCREENS
The complete system configurations can be allocated between multiple screens. Each screen can display a
bitmap image representing the area of the building or floor where the units or groups are physically located
THIRD PARTY EQUIPMENT MONITORING
Monitor general equipment Run and Faults via the PAC-YG66DCA interface and Temperature and Humidity via the PAC-YG63MCA
THIRD PARTY EQUIPMENT CONTROL
Control general equipment On/Off via the PAC-YG66DCA
EMAIL
The following information may be sent regularly and automatically via email: energy monitoring data,
energy saving data, trend logging data (temperatures etc) and fault code history
TG2000 WAN Software /
TG2000 Screenshots
TG2000WAN (Wide Area Network) Software
FUNCTION
Icons available to suit model type installed
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
NOTE 2: The TG2000 WAN cannot be utilised if the following site functions are required: energy charging, energy saving and trend logging.
NOTE 3: Temperature and Humidity Sensors not supplied by MEUK
Page 290
Page 291
BEMS BACnet Interface
Controls Range
BEMS BACnet Interface
®
®
BAC-HD150
Procon BAC-IP/50
TM
®
To further enhance our complete open system network offering, we offer a BACnet interface solution.
Utilising the ASHRAE BACnet standard, complete control and monitoring integration can be achieved
with up to 50 air conditioning units.
®
®
To further enhance our complete open system network offering, we offer a BACnet interface solution.
Utilising the ASHRAE BACnet standard, complete control and monitoring integration can be achieved
with up to 50 air conditioning units.
®
BAC-HD150
M-NET
*NOTE 1
ETHERNET
PAC-SC51KUA
TCP / IP
TCP / IP
Technical Information
BAC-IP/50
Technical Information
BACnet INTERFACE
®
BACnet INTERFACE
FUNCTION
BAC-HD150
COMPATIBLE WITH
MAX No. OF
INDOOR UNITS
50
Andover Controls
CENTRALISED CONTROLLER
REQUIRED
No
York BMS
POWER SUPPLY
240VAC 3.2A
COMPATIBILITY
City Multi
Mr Slim via PAC-SF81MA
M Series via MAC-399IF
BEMS CONNECTION
Ethernet
DIMENSIONS - mm (WxDxH)
250x97x266
®
FUNCTION
BAC-IP/50
COMPATIBLE WITH
MAX No. OF
INDOOR UNITS
50
Andover Controls
CENTRALISED CONTROLLER
REQUIRED
Yes (AG150 or GB50)
POWER SUPPLY
24VAC 0.5A
COMPATIBILITY
City Multi
Mr Slim via PAC-SF81MA
M Series via MAC-399IF
York BMS
Siemens
BEMS CONNECTION
Ethernet via HUB
DIMENSIONS - mm (WxDxH)
144x34x104
Priva Building Intelligence
Delta Controls
Delta Controls
®
®
NETWORK VARIABLE
POINT TYPE
NOTES
FUNCTION
NETWORK VARIABLE
POINT TYPE
NOTES
On/Off
Digital Input
Run/Stop
On/Off
Digital Input
Run/Stop
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
Permit / Prohibit
Digital Input
On/Off, Mode, Setpoint
Permit / Prohibit
Digital Input
On/Off, Mode, Setpoint
Airflow Direction
Analogue Input
Horizontal - 60,80,100º swing
Airflow Direction
Analogue Input
Horizontal - 60,80,100º swing
Filter Sign
Digital Input
Normal/Reset
Filter Sign
Digital Input
Normal/Reset
Run/Stop
On/Off
Digital Output
Run/Stop
Analogue Output
Cool / Dry / Heat / Auto / Fan
BEMS BACnet® Interfaces
Control
Control
Monitor
Monitor
On/Off
Digital Output
Mode Operation
Analogue Output
Cool / Dry / Heat / Auto / Fan
Mode Operation
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Permit / Prohibit
Digital Output
On/Off, Mode, Setpoint
Permit / Prohibit
Digital Output
On/Off, Mode, Setpoint
Airflow Direction
Analogue Output
Horizontal - 60,80,100º swing
Airflow Direction
Analogue Output
Horizontal - 60,80,100º swing
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Filter Sign
Digital Output
-
Filter Sign
Digital Output
-
Room Temperature
Analogue Output
-
Room Temperature
Analogue Output
-
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Page 292
Priva Building Intelligence
BACnet INTERFACE
BACnet INTERFACE
FUNCTION
Siemens
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Page 293
®
Procon BAC-A/50
BEMS LonWorks Interface
®
LMAP
TM
®
A new BACnet Interface has been specially developed for the Mr Slim systems. The BAC-A/50 can control up to
50 individual systems.
The Mitsubishi Electric LMAP continues to strengthen the ability of our products to interface with other third party
building control systems using the globally recognised and accepted open network protocol Echelon LonWorks®.
LonWorks® was introduced into the building services industry a number of years ago with the aim of establishing
itself as the defacto communications standard. Many hundreds of products now exist that utilise the LonWorks®
protocol from complete systems like BEMS, lighting, power monitoring and security down to simple sensors
and relay switches.
To ensure that our products can connect directly and easily with other LonWorks® products, the L-MAP02
was designed utilising Echelon MIPS technology and was the first to provide data in the LonWorks®
SNVT (Standard Network Variable Type) format.
PAC-SK82SI
Controls Range
BEMS BACnet Mr Slim Interface
M-NET
TCP / IP
BAC-A/50
FTT-10
LMAP
Technical Information
Technical Information
®
LMAP LonWorks INTERFACE
BACnet MR SLIM INTERFACE
®
FUNCTION
BAC-A/50
COMPATIBLE WITH
FUNCTION
LMAP
COMPATIBLE WITH
MAX No. OF
INDOOR UNITS
50
Andover Controls
MAX No. OF
INDOOR UNITS
50
Honeywell
CENTRALISED CONTROLLER
REQUIRED
No
York BMS
CENTRALISED CONTROLLER
REQUIRED
No
POWER SUPPLY
240VAC 0.5A
Siemens
POWER SUPPLY
240VAC 0.5A
COMPATIBILITY
Mr Slim via PAC-SK82SI
Priva Building Intelligence
COMPATIBILITY
BEMS CONNECTION
Ethernet
City Multi
Mr Slim via PAC-SF81MA
M Series via MAC-399IF
DIMENSIONS - mm (WxDxH)
270x75x210
Delta Controls
BEMS CONNECTION
LonWorks FTT-10
DIMENSIONS - mm (WxDxH)
340x60x360
Johnson Controls
POINT TYPE
®
LMAP LonWorks INTERFACE
NOTES
Control
NETWORK VARIABLE
POINT TYPE
NOTES
Control
On/Off
Digital Input
Run/Stop
On/Off
Digital Input
Run/Stop
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
Permit / Prohibit
Digital Input
On/Off, Mode, Setpoint
Permit / Prohibit
Digital Input
On/Off, Mode, Setpoint (only available when using PAC-YT51CRA or PAR-21MAA)
Filter Sign
Digital Input
Normal/Reset
Filter Sign
Digital Input
Normal/Reset
On/Off
Digital Output
Run/Stop
On/Off
Digital Output
Run/Stop
Mode Operation
Analogue Output
Cool / Dry / Heat / Auto / Fan
Mode Operation
Analogue Output
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Permit / Prohibit
Digital Output
On/Off, Mode, Setpoint
Permit / Prohibit
Digital Output
On/Off, Mode, Setpoint (only available when using PAC-YT51CRA or PAR-21MAA)
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Filter Sign
Digital Output
-
Filter Sign
Digital Output
-
Room Temperature
Analogue Output
-
Room Temperature
Analogue Output
-
Monitor
Monitor
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Page 294
FUNCTION
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Page 295
BEMS BACnet® Mr Slim Interface /
BEMS LonWorks® Interface
®
NETWORK VARIABLE
(LTX51/LTX21 via VCI)
Smart Controls
BACnet MR SLIM INTERFACE
FUNCTION
Realtime Control Systems
BEMS Modbus Mr Slim Interface
Procon MOD-IP/50
Procon A32M
To further complement the existing control and interface product ranges being offered by Mitsubishi Electric to
support their air conditioning systems, the Modbus range has been developed to accommodate the typical
end-user needs as experienced within the UK market.
To further complement the existing control and interface product ranges being offered by Mitsubishi Electric
to support their air conditioning systems, the Modbus range has been developed to accommodate the typical
end-user needs as experienced within the UK market.
TM
TM
M-NET
PAC-SK82SI
*NOTE 1
Controls Range
BEMS Modbus Interface
ETHERNET
PAC-SC51KUA
Modbus
RS232 / 485
Modbus
A32M
RS232 / 485 or TCP / IP
Technical Information
Technical Information
MODBUS INTERFACE
FUNCTION
MOD-IP/50
COMPATIBLE WITH
MAX No. OF
INDOOR UNITS
50
Trend via Synapsys SXNC200
CENTRALISED CONTROLLER
REQUIRED
Yes (AG150 or GB50)
POWER SUPPLY
240VAC 0.5A
COMPATIBILITY
City Multi
Mr Slim via PAC-SF81MA
M Series via MAC-399IF
MODBUS MR SLIM INTERFACE
FUNCTION
A32M
COMPATIBLE WITH
MAX No. OF
INDOOR UNITS
32
Trend via Synapsys SXNC200
CENTRALISED CONTROLLER
REQUIRED
No
POWER SUPPLY
240VAC 0.5A
Invensys
North BT
COMPATIBILITY
Mr Slim via PAC-SK82SI
Interactive Homes
Cylon
Satchwell
Crestron (Home automation)
Invensys
Interactive Homes
Cylon
Satchwell
Crestron (Home automation)
North BT
BEMS CONNECTION
Serial RS232, RS485 or TCP / IP
Andover
BEMS CONNECTION
Serial RS232 or 485
Andover
DIMENSIONS - mm (WxDxH)
144x34x104
Siemens
DIMENSIONS - mm (WxDxH)
270x75x210
Siemens
NOTES
MODBUS MR SLIM INTERFACE - OPERATIONAL INFORMATION
FUNCTION
NETWORK VARIABLE
POINT TYPE
Control
On/Off
Digital Input
Run/Stop
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
Permit / Prohibit
Digital Input
On/Off, Mode, Setpoint
Airflow Direction
Analogue Input
Horizontal - 60,80,100º swing
Filter Sign
Digital Input
Normal/Reset
Monitor
NETWORK VARIABLE
POINT TYPE
NOTES
Control
On/Off
Digital Input
Run/Stop
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC
Heating 17-28ºC
Auto 19-28ºC
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
Monitor
On/Off
Digital Output
Run/Stop
Mode Operation
Analogue Output
Cool / Dry / Heat / Auto / Fan
On/Off
Digital Output
Run/Stop
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Mode Operation
Analogue Output
Cool / Dry / Heat / Auto / Fan
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC
Permit / Prohibit
Digital Output
On/Off, Mode, Setpoint
Airflow Direction
Analogue Output
Horizontal - 60,80,100º swing
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Filter Sign
Digital Output
-
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Room Temperature
Analogue Output
-
Room Temperature
Analogue Output
-
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Page 296
FUNCTION
BEMS Modbus Interface /
BEMS Modbus Mr Slim Interface
MODBUS INTERFACE - OPERATIONAL INFORMATION
Heating 17-28ºC
Auto 19-28ºC
NOTE: Not available on SEZ / SLZ
Page 297
Procon A1M
Procon KNX-EIB-IP-15/100
To further complement the existing control and interface product ranges being offered by Mitsubishi Electric
to support their air conditioning systems, the Modbus range has been developed to accommodate the typical
end-user needs as experienced within the UK market.
To further complement the existing control and interface product ranges being offered by Mitsubishi Electric to
support their air conditioning systems, the KNX-EIB range has been developed to accommodate the typical
end-user needs as experienced within the UK market.
TM
TM
M-NET
*NOTE 1
ETHERNET
Controls Range
BEMS KNX-EIB Interfaces
BEMS Modbus Splits Interface
PAC-SC51KUA
A1M
KNX-EIB
Modbus
RS485
KNX-EIB-IP-15
KNX-EIB-IP-100
Technical Information
MODBUS SPLITS INTERFACE
FUNCTION
A1M
COMPATIBLE WITH
MAX No. OF
INDOOR UNITS
1
CENTRALISED CONTROLLER
REQUIRED
No
Trend via Synapsys SXNC200
Cylon
Satchwell
Crestron (Home automation)
Invensys
Interactive Homes
North BT
Andover
Siemens
COMPATIBILITY
M Series
Mr Slim
BEMS CONNECTION
Serial RS485
DIMENSIONS - mm (WxDxH)
72x27x50
KNX-EIB CITY MULTI INTERFACES
FUNCTION
KNX-EIB-IP-15
KNX-EIB-IP-100
COMPATIBLE WITH
ABB
MAX No. OF
INDOOR UNITS
15
100
CENTRALISED
CONTROLLER
REQUIRED
Yes (AG150 or GB50)
Yes (AG150 or GB50)
POWER SUPPLY
9 to 30VDC or 24VAC 0.5A
9 to 30VDC or 24VAC 0.5A
COMPATIBILITY
City Multi
Mr Slim via PAC-SF81MA
M Series via MAC-399IF
City Multi
Mr Slim via PAC-SF81MA
M Series via MAC-399IF
BEMS CONNECTION
Ethernet via HUB
Ethernet via HUB
DIMENSIONS - mm
(WxDxH)
107x58x105
107x58x105
Intelligent Buildings
Nova Controls Ltd
Siemens
MODBUS SPLITS INTERFACE - OPERATIONAL INFORMATION
KNX-EIB CITY MULTI INTERFACE UNITS - OPERATIONAL INFORMATION
FUNCTION
FUNCTION
NETWORK VARIABLE
POINT TYPE
NOTES
NETWORK VARIABLE
POINT TYPE
BEMS Modbus Splits Interface /
BEMS KNX-EIB Interfaces
Technical Information
NOTES
Control
Control
On/Off
Digital Input
Run/Stop
On/Off
Digital Input
Run/Stop
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC
Heating 17-28ºC
Heating 17-28ºC
Auto 19-28ºC
Auto 19-28ºC
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
Monitor
Monitor
On/Off
Digital Output
Run/Stop
On/Off
Digital Output
Run/Stop
Mode Operation
Analogue Output
Cool / Dry / Heat / Auto / Fan
Mode Operation
Analogue Output
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC
Heating 17-28ºC
Heating 17-28ºC
Auto 19-28ºC
Auto 19-28ºC
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Room Temperature
Analogue Output
-
Room Temperature
Analogue Output
-
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Page 298
Page 299
BEMS Trend Interface
Procon KNX-EIB-A-1
Trend IQ3 Excite
To further complement the existing control and interface product ranges being offered by Mitsubishi Electric
to support their air conditioning systems, the KNX-EIB range has been developed to accommodate the typical
end-user needs as experienced within the UK market.
Mitsubishi Electric and Synapsys Solutions have been working together for the last six years to offer very
competitive solutions for Trend users. The IQ3 Excite Interface has been modified by Synapsys Solutions to
work directly in conjunction with the AG150 and GB50 centralised controllers. This allows Trend users to
easily integrate Trend systems with Mitsubishi Electric air conditioning.
TM
Controls Range
BEMS KNX-EIB Splits Interface
M-NET
*NOTE 1
ETHERNET
KNX-EIB-A-1
PAC-SC51KUA
KNX-EIB
Trend
IQ3 Excite
(must be supplied by Synapsys)
Technical Information
TREND INTERFACE
Technical Information
KNX-EIB SPLITS INTERFACE
FUNCTION
KNX-EIB-A-1
COMPATIBLE WITH
MAX No. OF
INDOOR UNITS
1
ABB
CENTRALISED CONTROLLER
REQUIRED
No
COMPATIBILITY
FUNCTION
IQ3 EXCITE
COMPATIBLE WITH
MAX No. OF INDOOR UNITS
50
Trend only
CENTRALISED CONTROLLER
REQUIRED
Yes (AG150 or GB50)
POWER SUPPLY
240VAC
COMPATIBILITY
City Multi
Mr Slim via PAC-SF81MA
M Series via MAC-399IF
BEMS CONNECTION
Ethernet via HUB
DIMENSIONS - mm (WxDxH)
263x42x130
Intelligent Buildings
M Series
Mr Slim
Nova Controls Ltd
BEMS CONNECTION
KNX (TP-1) EIB
DIMENSIONS - mm (WxDxH)
60x25x48
Siemens
IMPORTANT NOTE: The IQ3 Excite Interface can only be supported by Synapsys Solutions (Tel: 01273 831831)
KNX-EIB SPLITS INTERFACE - OPERATIONAL INFORMATION
FUNCTION
NETWORK VARIABLE
POINT TYPE
NOTES
NETWORK VARIABLE
POINT TYPE
NOTES
Control
Control
On/Off
Switch
Run/Stop
Mode Operation
Knob
Cool / Dry / Heat / Auto / Fan
On/Off
Digital Input
Run/Stop
Setpoint Adjustment
Knob
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Mode Operation
Analogue Input
Cool / Dry / Heat / Auto / Fan
Fan Speed Control
Knob
Lo-Mi1-Mi2-Hi
Setpoint Adjustment
Analogue Input
Cooling 19-30ºC
Permit / Prohibit
Digital Input
On/Off, Mode, Setpoint
Heating 17-28ºC
Airflow Direction
Knob
Horizontal - 60,80,100º swing
Auto 19-28ºC
Filter Sign
Digital Input
Normal/Reset
Fan Speed Control
Analogue Input
Lo-Mi1-Mi2-Hi
On/Off
Switch
Run/Stop
On/Off
Digital Output
Run/Stop
Mode Operation
Knob
Cool / Dry / Heat / Auto / Fan
Mode Operation
Analogue Output
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Knob
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Setpoint Adjustment
Analogue Output
Cooling 19-30ºC
Fan Speed Control
Knob
Lo-Mi1-Mi2-Hi
Heating 17-28ºC
Permit / Prohibit
Digital Output
On/Off, Mode, Setpoint
Auto 19-28ºC
Airflow Direction
Knob
Horizontal - 60,80,100º swing
Monitor
BEMS KNX-EIB Splits Interface /
BEMS Trend Interface
TREND INTERFACES
FUNCTION
Monitor
Fan Speed Control
Analogue Output
Lo-Mi1-Mi2-Hi
Fault Code
Sensor
4 Character code - Indicates all unit alarms
Fault Code
Analogue Output
4 Character code - Indicates all unit alarms
Filter Sign
Digital Output
-
Room Temperature
Analogue Output
-
Room Temperature
Sensor
-
*NOTE 1: Applicable with AG150 / PAC-SC51KUA or GB50
Page 300
Page 301
Procon Maxi M2M-IP/50
TM
To offer remote management of its air conditioning units to companies with large numbers of dispersed offices,
Mitsubishi Electric has adopted the M2M platform. The machine-to-machine (M2M) technology platform
allows customers to integrate multiple sites into one network. The air conditioning units as well as third party
equipment will be wirelessly connected to the M2M server and use the GPRS network to communicate.
GB50ADA
Maxi M2M-IP/50
MEUK
M2M
SERVER
METER 1
METER 2
METER 3
METER 4
EQUIPMENT 1
EQUIPMENT 2
SENSOR 1
SENSOR 2
M2M - Machine 2 Machine
Splits Interface
Controls Range
M2M - Machine 2 Machine Interface
Procon Mini M2M-A/16
TM
To offer remote management of its air conditioning units
to companies with large numbers of dispersed offices,
Mitsubishi Electric has adopted the M2M platform.
The machine-to-machine (M2M) technology platform
allows customers to integrate multiple sites into one
network. The air conditioning units as well as third
party equipment will be wirelessly connected to
the M2M server and use the GPRS network
to communicate.
Mini M2M-A/16
A1M
A1M
GPRS
Maxi M2M-IP/50
MEUK
GB50ADA
METER 1
M2M
SERVER
METER 2
METER 3
METER 4
Mini M2M-A/16
METER 1
METER 2
METER 3
METER 4
EQUIPMENT 1
EQUIPMENT 2
SENSOR 1
EQUIPMENT 1
EQUIPMENT 2
SENSOR 1
SENSOR 2
GPRS
A1M
A1M
SENSOR 2
Technical Information
METER 1
METER 2
METER 3
M2M INTERFACE
DESCRIPTION
MAX No. OF INPUTS
22 (4 to 20mA, 0 to 10VDC, 10kΩ resistor, digital)
M2M SPLITS INTERFACE
4 (volt free contact)
12 (pulse with modulation)
FUNCTION
DESCRIPTION
MAX No. OF OUTPUTS
MAX No. OF INPUTS
8 (4 to 20mA, 0 to 10VDC, 10kΩ resistor, digital)
MAX No. OF INDOOR UNITS
50
MAX No. OF OUTPUTS
4 (pulse with modulation)
SIM CARD
Vodafone Sim Card supplied with one year contract
MAX No. OF INDOOR UNITS
16
M2M SERVER HOSTING
First year free of charge
SIM CARD
Vodafone Sim Card supplied with one year contract
POWER SUPPLY
240VAC 2A
M2M SERVER HOSTING
First year free of charge
COMPATIBILITY
City Multi, Mr Slim and M Series
POWER SUPPLY
240VAC 2A
300x70x350
COMPATIBILITY
Mr Slim and M Series via Procon A1M
DIMENSIONS - mm
M2M INTERFACE - OPERATIONAL INFORMATION
FUNCTION
UP TO 25 GROUPS
UP TO 50 GROUPS
On/Off
Run/Stop
Mode Operation
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Fan Speed Control
Lo-Mi1-Mi2-Hi
Permit / Prohibit
On/Off, Mode, Setpoint
Airflow Direction
Horizontal - 60,80,100º swing
Filter Sign
Normal/Reset
NETWORK VARIABLE
NOTES
Control
SENSOR 1
SENSOR 2
255x60x180
(WxDxH)
M2M SPLITS INTERFACE - OPERATIONAL INFORMATION
FUNCTION
Monitor
NETWORK VARIABLE
NOTES
On/Off
Run/Stop
Control
Mode Operation
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Cooling 19-30˚C
Heating 17-28˚C
Auto 19-28˚C
Fan Speed Control
Lo-Mi1-Mi2-Hi
Time Zone
Weekly scheduling available
Run/Stop
Monitor
On/Off
Run/Stop
Mode Operation
Cool / Dry / Heat / Auto / Fan
On/Off
Setpoint Adjustment
Cooling 19-30ºC, Heating 17-28ºC, Auto 19-28ºC
Mode Operation
Cool / Dry / Heat / Auto / Fan
Fan Speed Control
Lo-Mi1-Mi2-Hi
Setpoint Adjustment
Cooling 19-30˚C
Permit / Prohibit
On/Off, Mode, Setpoint
Airflow Direction
Horizontal - 60,80,100º swing
Fault Code
Filter Sign
Room Temperature
4 Character code - Indicates all unit alarms
-
-
Heating 17-28˚C
Auto 19-28˚C
Fan Speed Control
Lo-Mi1-Mi2-Hi
Fault Code
4 Character code – Indicates all unit alarms
Room Temperature
-
Time Zone
Weekly scheduling available
DEMONSTRATION
DEMONSTRATION
Visit m2m.mitsubishielectric.co.uk/demo to use the live demonstration space (login: demo / password: demo)
Visit m2m.mitsubishielectric.co.uk/demo to use the live demonstration space (login: demo / password: demo)
Page 302
EQUIPMENT 2
M2M Interface / M2M Splits Interface
(WxDxH)
EQUIPMENT 1
Technical Information
FUNCTION
DIMENSIONS - mm
METER 4
Page 303
M2M-Machine 2 Machine
Web Screenshots
MEUK Website
Login
M2M is accessible using MEUK website.
A username and password is required to monitor
and control sites.
Monitor Active Alarms and Sites
Status
All sites are listed with active alarm sites.
A site can be selected to monitor each system.
Set Parameters
Reports
Indoor unit and third party equipment can be
controlled from the Website.
Reports can be generated for analysis.
Dashboard
Administration
AG150/GB50 web pages are available
for the air conditioning units
Using the administration level, the phone numbers
and email of each duty engineer may be set
and activated.
Procon Micro M2M-SMS-A/08
TM
The Micro M2M can monitor and control up to 8 splits systems. The Micro M2M cannot be connected to the
M2M server but can be monitored and controlled using text messages (SMS).
Micro
M2M-SMS-A/08
A1M
A1M
SMS
Micro
M2M-SMS-A/08
A1M
Controls Range
M2M - Machine 2 Machine
Splits Interface
A1M
Technical Information
M2M SPLITS INTERFACE
FUNCTION
DESCRIPTION
MAX No. OF INDOOR UNITS
8
POWER SUPPLY
10 to 28VDC 2.5A
COMPATIBILITY
Mr Slim and M Series via Procon A1M
DIMENSIONS - mm
(WxDxH)
70x51x105
M2M SPLITS INTERFACE - OPERATIONAL INFORMATION
FUNCTION
NETWORK VARIABLE
NOTES
On/Off
Run/Stop
Control
Mode Operation
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Cooling 19-30˚C
Heating 17-28˚C
Auto 19-28˚C
Fan Speed Control
Lo-Mi1-Mi2-Hi
On/Off
Run/Stop
Monitor
Mode Operation
Cool / Dry / Heat / Auto / Fan
Setpoint Adjustment
Cooling 19-30˚C
Heating 17-28˚C
Lo-Mi1-Mi2-Hi
Fault Code
4 Character code – Indicates all unit alarms
TEXT MESSAGE EXAMPLES
REGISTER (FROM MOBILE PHONE)
To register the Micro M2M to your mobile phone, just text the PIN and “ADD”. Up to 8 numbers can be
registered. For example: “1234 ADD” 1234 being the last 4 digits of the serial number
MONITOR
To monitor the units, just text “STATUS” to the unit and the Micro M2M will reply with, for example:
STATUS UNIT1: OK A1M COMMS: OK DRIVE:OFF ROOM TEMP:22 TEMP SETPOINT:20 MODE:AUTO FAN:HIGH
CONTROL
To switch the unit to heat mode, just text “SET” “unit name” and “HEAT” for example: “SET UNIT1 HEAT”
FAULTS
If the unit goes into fault, the Micro M2M will send a detailed text message, for example:
STATUS UNIT1: FAULT A1M COMMS: FAULT CALL 0870 3000300 FOR ASSISTANCE
Technical Information
Page 304
Page 305
M2M Splits Interface /
M2M Web Screenshots
Auto 19-28˚C
Fan Speed Control
Split-System A2M Interfaces
Procon PANEL_RS_SMS
TM
The panel PANEL_RS_SMS replaces the previous run standby panels. The new panel is smaller and uses Micro M2M
technology. The panel can control up to 8 indoor units and will send a text message under fault condition.
The PANEL_RS_SMS does not need the SIM card to run.
Procon
PANEL_RS_SMS
TM
A1M
The City Multi systems use advanced communication protocol called M-NET. The Split-Systems can be interfaced to
M-NET, allowing compatibility with the main centralised controller (AG150, GB50, TG2000). An A2M adapter would
be required per outdoor unit for Mr Slim and per indoor unit for Mr Slim S Series or M Series indoor units.
A1M
SMS
PAC-SF81MA
Controls Range
Run Standby Panel
Technical Information
PROCON PANEL_RS_SMS
TM
FUNCTION
DESCRIPTION
MAX No. OF INDOOR UNITS
8
FEATURES
Buzzer / Fault LED / Auto/Manual override switch / Relay for fault output
POWER SUPPLY
240VAC 2A
COMPATIBILITY
Mr Slim and M Series via Procon A1M
(WxDxH)
253x90x180
TEXT MESSAGE EXAMPLES
REGISTER (FROM MOBILE PHONE)
To register the Micro M2M to your mobile phone, just text the PIN and “ADD”. Up to 8 numbers can be
registered. For example: “1234 ADD” 1234 being the last 4 digits of the serial number
SET UP USING A TEXT
Enter the number of units running, the number of days to switch over and the high temperature alarm, for
example: “BACKUP ON, 3, 7, 27” (“ON” to activate, “3” for 3 units running, “7” to switch over every 7 days
and “27” for the high temperature alarm [all the units will be switch ON])
Example: “BACKUP ON, 2, 1, 27” = 2 units running, change daily, high temperature 27ºC
Unit 1
Unit 2
Unit 3
Unit 4
Day 1
2 units running, unit 3 and 4 are in standby
Day 2
2nd day, the switching over is enabled. Unit 1 and 4
are now in standby and Unit 2 and 3 are running
Day 3
3rd day, the switching over is enabled. Unit 1 and 2
are now in standby and Unit 3 and 4 are running
Day 3
On the 3rd day, the unit 4 fails
Day 3
The next unit in standby starts automatically.
Unit 1 and 3 are running, 2 is in standby and 4 in fault
Day 4
The 4th day, a high temperature is detected for instance 28ºC
Day 4
All units will then start
Technical Information
SPLIT-SYSTEM A2M INTERFACES
FUNCTION
PAC-SF81MA
MAC-399IF
COMPATIBILITY
Mr Slim Outdoor Unit
Mr Slim S Series / M Series Indoor Unit
CONNECTION TO
Outdoor Unit
Indoor Unit
MNET SETTINGS
Rotary Switches
Dip Switches
130x15x90
160x55x70
DIMENSIONS - mm
(WxDxH)
Run Standby Panel /
Split-System A2M Interfaces
DIMENSIONS - mm
NOTE: The PANEL_RS_SMS is pre-configured as a PANEL_RS1 and can be re-configured as PANEL_RS2 or PANEL_RS3 using a jumper.
Page 306
Page 307