VOD705
VOD1021
DVD PLAYER
WITH
DROP-DOWN
VIDEO
MONITOR
®
ELECTRONICS CORP.
128-7092
Release Date: 6-28-04
128-7092
1 of 28
Important Notice
An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video
monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video
monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these
features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied.
An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear
or when the parking brake is not applied must be installed to the rear of the driver’s seat where it will not be visible, directly
or indirectly, to the operator of the motor vehicle. It is unlawful in most jurisdictions for a person to drive a motor vehicle
which is equipped with a screen that is located in the motor vehicle at any point forward of the back of the driver’s seat, or
that is visible, directly or indirectly, to the driver while operating the vehicle. In the interest of safety, the VOD1021 should
never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle.
Warnings
Do not use any solvents or cleaning materials when cleaning the video monitor.
Do not use any abrasive cleaners, they may scratch the screen. Use only a lightly dampened lint free cloth to wipe the
screen if it is dirty.
Lock the LCD screen in the fully closed position when not in use.
Before putting on headphones always adjust the volume setting to the lowest position.
Remember to leave the dome light switch in the off or auto positions when the vehicle is unattended, as the dome
lights, if left on, can drain the vehicle’s battery.
Do not put pressure on the screen.
Licensed under one or more of the following patents,
Patent NOS. 5,775,762 and 5,927,784
-2 -
128-7092
2 of 28
Features
Congratulations on your purchase of the Audiovox
VOD1021 DVD Player with Drop-Down Video Monitor.
The VOD1021 has been designed to give you and
your family many years of video entertainment in the
mobile environment. Please read the directions that
follow to familiarize yourself with the product and to
ensure that you obtain the best results from your
equipment.
Please note: Installation options vary, see the
individual owner’s manuals for each component in
your system to obtain a full understanding of each
component’s operation.
Safety Precaution
For safety reasons, when changing video media it is
recommended that the vehicle is not in motion, and
that you do not allow children to unfasten seat-belts
to change video media or make any adjustments to
the system.
System adjustments can be
accomplished using the remote control unit, while
seat-belts remain fastened. Enjoy your Audiovox
entertainment system but remember-safety of all
passengers remains the number one priority.
•
10.2” TFT Active Matrix Color LCD Monitor
•
Built-In DVD Player
•
DVD/CD/MP3 compatible
•
On Screen Display
•
16:9 and 4:3 Screen Mode (switchable)
•
IR Remote Repeater for AV1 & AV2 Inputs
•
Dual IR Sensors
•
Remote Control
•
Four Source Selection (DVD/AV1/AV2/AUX)
•
AUX Input for Game or Camcorder
•
6 Frequency FM Modulator
(Remote Control Accessible)
•
Dual Headphone Jacks
•
Built-In Dual IR Transmitter
•
Built-In Dome Lights with Switch
• Last position memory for DVD
-3-
128-7092
3 of 28
Controls and Indicators Diagram
1
2
3
4
5
1
6
7
8
8
21
20
19
18
17
9
10
11
12
13
14
16
15
-4 -
128-7092
4 of 28
Main Function Descriptions
1. DVD Disc insertion slot – For loading Disc.
12. FWD Button – Allows the user to seach in a forword direction
at 2X, 4X, 6X, 8X times the normal speed.
2. POWER Button – Bright red when system is on dim when
off.
13. Side Remote Sensor Eye – Allows the remote control to
operate the VOD1021, control volume to wired headphone
jacks and control the other accessories.
3. EJECT ( ) Button – For ejecting discs from the disc
compartment.
14. AUX Input
4. PLAY ( ) Button – This button is used to enter the play
mode.
•
Auxiliary Audio Right Input.
5. STOP ( ) Button – To stop playback.
•
Auxiliary Audio Left Input.
•
Auxiliary Video Input.
6. Infrared Transmitter and Sensor – Use to transmit audio
to wireless headphones. Also allows the remote control to
operate the VOD1021 and to control other accessories in
the system.
15. Drop Down LCD Panel.
16. Headphone Jack – Allow the use of wired headphones
with a 1/8” plug for listening to video program audio.
7. VOD1021 Ventilation Opening.
17. Screen release – Moves in direction of the arrow to release
the drop down screen.
8. Dome Lights – Provide additional interior illumination.
9. SOURCE Select – Used to select one of the four sources
(AV1, AV2, AUX, DVD).
18. VOLUME ( ) Button – Use this button to decrease the
volume level of the wired headphone jacks. It is also used
to make picture adjustments in the picture select mode.
10. REV Button– Allows the user to search in a backwards
direction at 2X, 4X, 6X, 8X times the normal speed.
19. FM Select Button – Each time this button is pressed the
FM Modulator will cycle through the following options: (FM
OFF – POD AUDIO – SAT AUDIO) The frequency of the
FM modulator will remain same.
11. PAUSE Button – Allows the user to pause the playback.
-5-
128-7092
5 of 28
20. VOLUME ( ) Button – Use this button to raise the volume
level of the headphone jacks. It is also used to make picture
adjustments in picture select mode. Note : Audiovox
recommends the use of the Audiovox HP275 Headphones
when using wired headphones.
21. Three position Dome Light Switch
• Auto – Automatically switches on the dome lights in
conjunction with the vehicle’s interior illumination.
• Off – The dome lights will not turn on in this position.
• On – Turns on the dome lights.
Note:The volume buttons will not effect the volume of the wireless
headphones or the wired FM modulator. When using these
devices the volume must be adjusted with the wireless
headphone volume control or with your radio’s volume control
(see page 15, Wireless Headphones, or page 16, Wired
FM Modulator).
-6 -
128-7092
6 of 28
Remote Control Operation
EJECT
POWER
1
32
SOURCE
2
3
4
5
31
AUTO
MEMORY
SKIP/
SEARCH
ERASE/
WRITE
–
+
30
6
29
CH
MUTE
PIX
28
7
8
9
Battery Installation
VOL
27
Enter
SETUP
MENU
26
25
24
10
Before attempting to operate your Remote Control, install the
batteries as described below.
1) Turn the Remote Control face down. Using a fingernail,
lift the battery cover off.
2) Install two “AAA” batteries as shown. Make sure that
proper polarity (+ or -) is observed.
3) Align the cover tabs with the remote control and press
down until the cover clicks.
The remote control will operate the VOD1021 and most Audiovox
VCP’s. It is not a universal remote control and will not control
equipment from other manufacturers.
11
RETURN
CH
REPEAT
23
12
13
14
34
33
21
22
35
20
19
15
18
16
17
-7-
128-7092
7 of 28
Remote Control Function Descriptions
*Function control is available on the unit and the remote control.
**Not used in this model.
1. POWER Button*
Press this button to turn the VOD1021 on. Press the button again to turn the VOD1021 off.
2. SOURCE Button*
Video signals from video equipment connected to the audio / video inputs can be displayed on the monitor by
pressing this button. Each time the button is pressed, the audio / video source will change sources in the
following order: DVD, AV1, AV2 and AUX.
3. AUTO MEMORY Button (AUTO PROGRAM Button)**
When the AUTO MEMORY button is pressed, all channels are searched and channels that are detected with
signals of sufficent levels are automatically stored.
4. SKIP/SEARCH Button**
This button selects betweeen SKIP and SEARCH mode. In “SKIP mode” the TV tuner will tune and stop on
channels that are programmed into memory when the CHANNEL UP/DOWN buttons are used. When in the
SEARCH mode, the TV will stop on all active channels.
5. ERASE/WRITE Button**
While tuned to a channel, pressing this button will either store or erase the channel from memory. The stored
channel numbers are displayed in “GREEN” on the LCD display screen, and the erased channel numbers are
displayed in “RED”.
-8 -
128-7092
8 of 28
6. Channel** Up ( ) Button
Used to scroll upward in menu options.
7. MUTE Button
Press this button to mute the audio.
Pressing the button again restores the sound to the previously set level.
8. ENTER Button
Used to confirm a selected setting or option.
9. LEFT (
) Button
Allows the user to shift left in the menu options.
10. MENU Button
Allows the user to access the DVD (DVD MODE) main menu and monitor menu (TV MODE).
11. RETURN Button**
Allows the user to return to the menu while PBC on.
Note: This function only present on VCD2.0.
12. TV Mode Select Button**
Switches certain function keys on the remote control for TV functions.
-9-
128-7092
9 of 28
13. DISPLAY Button
Press to display DVD Disc current information.
Press DISPLAY button
Once
Twice
3 times
4 times
5 times
6 times
7 times
DVD Player Perform
Display current TITLE & CHAPTER
Display current SUBTITLE
Display current AUDIO language & channel
Display current ANGLE
Display A-B current status
Display REPEAT current status
Display is turn off
For Title & Chapter, use cursor buttons to do title/chapter selection, then press Enter button to implement the selection.
For Subtitle, Audio, Angle, A to B & Repeat, press the Enter key repeatedly to change the options. These options may vary
from disc to disc.
14. PAUSE ( ) Button*
Allows the user to pause playback.
15. PREVIOUS ( ) Button
Allows the user to return to the previous chapter or track.
16. NEXT ( ) Button
Allows the user to skip to the next chapter or track.
-10-
128-7092
10 of 28
17. REV (
) Button*
Allows the user to search in a backward direction at 2,4, 6 and 8 times the normal speed for DVD.
Allows the user to activate the video tape rewind search mode for VCP.
18. FWD (
) Button*
Allows the user to search in a forward direction at 2,4, 6 and 8 times the normal speed for DVD.
Allows the user to activate the video tape fast forward search mode for VCP.
19. PLAY ( )Button*
Press this button to activate the play mode while a disc is loaded into the disc compartment for DVD.
Press this button to activate the play mode while a video tape compartment for VCP.
20. STOP (!) Button*
DVD disc play will be stopped.
Video tape play will be stopped
21. DVD Mode Select button
Switches certain function keys on the remote control for DVD functions.
22. VCP Mode Select button
Switches certain function keys on the remote control for VCP functions.
23. A-B Button
Allows the user to repeat play of a DVD or CD from point A to point B.
24. REPEAT Button
Allows the user to repeat various positions of a DVD, CD or MP3.
-11-
128-7092
11 of 28
25. Channel** Down ( ) Button
Used to scroll downward in the menu options.
26. SETUP Button
Allows the user to select the DVD player’s setup options (Display, OSD Language, Defaults, Parental Control,
Password, Exit Setup).
27. RIGHT (
) Button
Allows the user to shift to the right in the menu options.
28. PIX Button (PICTURE SELECT)
Each time this button is pressed, the unit will display “adjustment bars” for BRIGHTNESS, CONTRAST, COLOR
or TINT. Once the desired adjustment bar is displayed, use the VOLUME UP or DOWN buttons to adjust the
setting. The display will automatically turn off if no adjustments are made within 6 seconds, or if any other button
is pressed.
29. VOLUME DOWN (-) Button*
Use these buttons to decrease the volume level of the wired headphone jacks. This button is also used to make picture
adjustments in the picture select mode.
-12-
128-7092
12 of 28
30. VOLUME UP (+) Button*
Use this button to raise the volume level of the wired headphone jacks. This button is also used to make picture
adjustments in the picture select mode.
Note: The volume buttons will not affect the volume of wireless headphones or a wired FM modulator. When
using these devices the volume must be adjusted with the wireless headphone volume control or with your
radio’s volume control (see page 15, Headphones, or page 16, Wired FM Modulator).
31. NUMBER Buttons
- Allows the user to enter the numbers 0 to 9 for selection of CD tracks, DVD chapters, and password setting.
- Allows the user to enter the numbers 0 to 9 for selection of TV channel.
32. EJECT ( )Button*
Use this button to eject a disc.
33. FM TRANSMITTER ON/OFF Button
Turns FM Modulator power on/off.
34. SOURCE SELECT Button*
With FM ON, used to select from POD Audio (Selected Source mode) or SAT Audio (Second IR input).
With FM OFF, used to select from SAT Audio or Car Audio.
35. CHANNEL SELECT Button
Selects the FM modulator Frequency (Frequency 1, 88.3MHz, Frequency 2, 88.7MHz, Frequency 3, 89.1MHz,
Frequency 4, 89.5MHz, Frequency 5, 89.9MHz, Frequency 6, 90.3MHz).
-13-
128-7092
13 of 28
Turning the VOD1021 On or Off
1. Sliding the screen release lock in the direction of the arrow will unlock the LCD screen and it will drop down
slightly. Pivot the screen downward until a comfortable viewing angle is reached. The internal friction will hold the
screen in position while the system is in use.
2. Pressing the power button on the unit or the remote control will turn the system on or off alternately. When in use
the internal backlighting will illuminate the controls.
3. After the unit has been turned on and is displaying a picture, adjust the viewing angle by pivoting the screen to
optimize the picture quality.
4. Remember to turn the unit off and pivot the LCD to the locked position when not in use.
Overhead Dome Lights
The lights integrated into the VOD1021 are controlled
by a three position slide switch. Sliding the switch to
the on position will turn the lights on. The off position
will prevent the lights from turning on at all times, and
the auto position will allow the lights to turn on and off
with the vehicle’s interior lighting. Refer to the Installation
Manual for the wire connections. Do not leave the
vehicle unattended with the dome light switch in the on
position, as this could result in a discharged battery.
Dome Light
Switch
-14-
128-7092
14 of 28
Remote Sensor
The VOD1021 incorporates two Infrared sensors which relay signals
from the remote control to allow the unit to be controlled simply by
pointing its remote control at the remote sensor eye. The repeater
function allows control of auxiliary equipment such as an Audiovox
Video Cassette Player. The infrared sensor can relay signals from
most manufacturer’s remote controls to its respective component
connected to the AV1 or AV2 inputs. In this case you must use the
remote control supplied with the component.
Remote
Sensor
Eye
Remote
Sensor
Eye
Accessories
Wireless Headphones
The VOD1021 includes a built-in infrared transmitter for use with Audiovox wireless headphones (P/N IR2CHS). The
volume can then be adjusted using the controls on each headset. The wireless headphones must be used within a
line of sight from the transmitter, as infrared transmissions, like visible light travel only in a straight line. See the
documentation accompanying your Audiovox wireless headphones.
IR2 Input
Any line level audio source may be connected to this input (Satellite Radio, CD Changer etc). The audio program
connected to the IR2 input can be received on the B channel of the dual channel wireless headphones (P/N IR2CHS).
Headset Special Features
• Automatic Level Control prevents input signal over loading.
• Uses high frequency infrared light to assure a clean signal for clear reception.
-15-
128-7092
15 of 28
Wired Headphones
There are two 1/8” headphone jacks on the VOD1021 that can be used with any standard wired stereo headphones.
These jacks are controlled by the volume up / down buttons on the VOD1021 and on the remote control.
Wired FM Modulator
The VOD1021 is equipped with an RF modulator, that allows you to listen to the VOD1021 audio signal by tuning your
vehicle’s radio to the selected frequency, (88.3, 88.7, 89.1, 89.5, 89.9, 90.3MHz). This feature is accessed by using
either the FM transmitter buttons on the remote (On/Off, Source Select, Channel Select) or the FM Select button on
the unit. Whenever the RF modulator is on, broadcast reception on the vehicles radio will be poor. Switching off the
FM modulator will allow normal radio reception.
AV1 Input
The video inputs may be connected to a Video cassette Player (VCP), video game system, or any other audio / video
device. To access the A/V inputs, turn the VOD1021 on and press the source button on the VOD1021 or the Source
button on the remote control until “AV1” is displayed on the screen. Turn the video source component on with its power
button or remote control. The VOD1021 is now ready to play the audio and video signals from the source connected
to the AV1 input.
AUX Input
Using the supplied A/V Adapter Cable (P/N 112B3227) the VOD1021 will accept an audio / video input through the 1/8”
jack located on the side of the unit. The audio / video device could be a video game system, video camera, or other
input device.
Video Out
The VOD1021 provides a video output for an optional video monitor(s). (Refer to page 6 of the Installation Guide for
more details.) This output will provide a video signal that duplicates the signal displayed by the VOD1021 to an additional
monitor or video display. Please see your installer for more information.
-16-
128-7092
16 of 28
DVD Basics
To get the optimum use out of the DVD section, make sure you read this section completely.
Regional Coding
Both the DVD player and DVD’s are coded by region. These regional codes must match in order for the disc to play.
If the codes don’t match, the disc won’t play. This unit’s code is region 1. Other regional codes cannot be played in
this unit. The unit will display “WRONG REGION.”
Types of Discs your DVD will play
• DVD discs – DVD discs which contain video.
• Audio discs – Audio CDs contain musical or sound content only.
• MP3 discs – A disc that contains audio files (for example, a CD-R with downloaded MP3 files).
• VCD discs –VCD discs which contain video.
Loading and Playing Discs
Before you load a disc, make sure that it is compatible with the player.
Note: the following Discs CANNOT be used with this player :
• MiniDisc
• Laserdisc
• CD-I, CD-ROM, DVD-ROM
To load and Play a Disc
Press the Power button to turn the unit ON. Select DVD mode and insert the disc (Label Up) into the disc compartment.
-17-
128-7092
17 of 28
Settings and Adjustments
This chapter describes how to set and how to adjust using the on-screen DVD SETUP menu.
Using the Setup Menu
Using the setup display, you can do the initial setup, adjust the picture display ratio (16:9 or 4:3) and set the various
outputs. You can also select a language for the on-screen display, setup display and limit playback by children.
1) Press the SETUP button to display the “setup menu” on the display screen.
2) Select the main item you want using the cursor (▼▲) buttons, and then press the ! to enter the submenu.
To Cancel Using the Setup Display
Press the SETUP button on the remote.
Setting the Language for On-Screen Display
Press the SETUP button and using the
(▼▲)buttons select “OSD LANGUAGE”.
OSD (On-Screen Display) Language Menu
The OSD Language Menu allows the user to select
the language for the on-screen display. Press !
and then use the (▼▲) buttons to select the desired
language. The user can select either English, French
or Spanish for the OSD language. Press enter to
confirm the setting, then press " to return to the
main menu.
-18-
128-7092
18 of 28
Settings for Display
Press the SETUP button and select Display. The DISPLAY
SETUP allows you to adjust screen setting (aspect ratio) Press
and then use the (▼▲)buttons to select the appropriate
settings.
4:3 / PS
This displays the wide picture on the screen with a
portion of the left & right side removed.
4:3 / LB
This displays the wide picture with black bands on the
upper and lower portions of the screen.
16:9
This displays a picture with black bands on the upper
and lower portion of the screen.
Then press ENTER to confirm your selection, then press "
to return to the main menu. .
Defaults Settings
Press the SETUP button and select Defaults. The DEFAULTS
SETUP allows you to reset ALL options to factory defaults.
Press and then press Enter to implement the reset.
Note : This function will not effect the Parental setting.
-19-
128-7092
19 of 28
Settings for Parental (Parental Control)
This section of the SETUP Menu allows user to control the content of movie playback from G to Adult.
The Parental Control function allows you to limit viewing to your preference.
1. Use the ▼▲ buttons to select from:
G (Children)
PG
PG 13
R
NC-17
ADULT (Adult)
Note:The lower the value, the more strict the limitation.
Press the Enter button to confirm the selection.
2. Input a password in 4 digits using the numeric buttons then press the Enter button.
NOTE: The Default Password is 3308. This password is always effective even after you have selected your own
password and changed it. To avoid the possibility of others using the default password to set the parental level
and change the password, you can record this default password in another area and delete it from this manual.
Some discs can be limited depending on the age of users while some discs can not.
-20-
128-7092
20 of 28
Settings for Password (Parental Control Password)
Press the SETUP button and select PASSWORD. The PASSWORD SETUP allows you to change the parental
control password. Press and then press Enter.
OLD PASSWORD
Input the old password or the default password (4 digits)
NEW PASSWORD
Input a new password (4 digits) using numeric buttons
CONFIRM PASSWORD
Confirm the new password by entering the same new password again.
Then press Enter to implement it.
-21-
128-7092
21 of 28
Playing Audio CDs
When playing an audio CD, the DISPLAY Banner appears automatically. It displays the current track and the amount of the
time for that track playing, the total amount of time on the disc and the current time running on the disc. Press the DISPLAY
button on the remote to display the DISPLAY Banner. The options below show you what happens when you press the
DISPLAY button.
Press DISPLAY 1x
SINGLE ELAPSED appears along with the current track playing and the time of that track.
Press DISPLAY 2x
SINGLE REMAIN appears along with the current track playing the and the amount of time left
for the track.
Press DISPLAY 3x
TOTAL ELAPSED appears along with the current track playing and the total time the disc has
been playing.
Press DISPLAY 4x
TOTAL REMAIN appears along with the current track playing and the amount of time left on
the CD.
Press DISPLAY 5x
Turns off the DISPLAY Banner.
Using the REPEAT Feature
The default mode for the Repeat feature is OFF. Pressing REPEAT consecutively changes the repeat options:
• REP-ONE- repeats the track that is playing.
• REP-ALL- repeats the disc that is playing.
• REPEAT OFF
As you toggle through the options, the repeat option changes at that time. The tracks, for example, repeats once that tracks
has ended. The selected repeat option loops repeatedly until you turn it off.
-22-
128-7092
22 of 28
Playing MP3 Discs
MP3 is a format for storing digital audio. An audio CD-quality song can be compressed into the MP3 format with very little
loss of quality, while taking up much less space. CD-R discs that have been encoded in MP3 format can be played on your
DVD player.
Press the DISPLAY button on the remote to show the DISPLAY Banner. The options below show you what happens when
you press the DISPLAY button.
Press DISPLAY 1x
TIME REMAIN appears along with the amount of time left in the song that is playing.
TIME REMAIN and the time that is left will remain on the screen until you press DISPLAY
again.
Press DISPLAY 2x
TIME ELAPSED appears along with the amount of time the song has played. TIME ELAPSED
and the time will remain on the screen until you press DISPLAY again.
Press DISPLAY 3x
OFF appears and the display will no longer be displayed.
..
MP3
MP3
MP3
MP3
MP3
-23-
128-7092
23 of 28
Selecting Folders and Songs
When an MP3 disc is inserted in the player, the Smart Nav screen appears automatically. You can change folders and
songs through Smart Nav. The DVD player plays the songs in order they were burned on to the disc.
1. If a disc is playing, press STOP. Press the up or down arrow button to go through the folder list on the right side of the
Smart Nav screen.
2. Once the folder you want is highlighted, press Enter (the folder list shifts to the left side of the screen and the songs in
the folder appear on the right).
3. Press the up or down arrow button to go through the song list and highlight the song you want. Press Enter to begin
playback of the highlighted song.
Skipping Songs
Use the Next (
) button on the remote control to move to the next song. Use the Previous (
) button to move to the
beginning of the currently playing song. Press the
button 2 times to move to the previous song.
Using The Repeat Feature
1. SINGLE : Play a selected song.
2. FOLDER : Plays the folder in the order the songs were recorded.
3. REP_ONE : Repeats the song that is playing.
4. FOLDER REP : Repeats the folder that is playing.
5. DISC : Plays the entire disc.
6. DISC REP : Repeats the songs in the disc.
7. DISC SCAN : Plays the song for 10 second for each song in the disc.
-24-
128-7092
24 of 28
Troubleshooting
SOLUTION
PROBLEM
Poor in vehicle
radio reception
(FM modulator
installed)
• Check the condition of the vehicle’s
IR sensor
inoperative
• Verify that the batteries in the remote
PROBLEM
No sound or
distorted sound
radio antenna.
• Verify that the antenna is fully raised.
• If an wired FM modulator has been
installed, verify that it is turned OFF
by using the remote.
are fresh.
• Verify that the remote sensor eye is
Can’t advance
through a movie
not obstructed.
• Verify that the infrared transmitter is
affixed over the sensor eye of the
component to be controlled.
Disc won’t play
Play starts, but
then stops
immediately
• Insert a disc with the label side facing
up.
• Check the type of disc you put into
disc tray. This DVD player only plays
DVD’s, audio CDs and MP3s.
• Both the unit and the disc are coded
by region. If the regional codes don’t
match, the disc can’t be played. This
DVD player is Region Number 1.
The icon (
appears on
screen
• The disc is dirty. Clean it.
• Condensation has formed. Allow
player to dry out.
)
SOLUTION
• Make sure your DVD player is
connected properly. Make sure all
cables are securely inserted into the
appropriate jacks.
• If you are using the IR headphones,
make sure you turn on the IR power.
• Make sure the Modulator is ON and
the proper Frequency has been
selected.
• You can’t advance through the
opening credits and warning
information that appears at the
beginning of movies because the
disc is programmed to prohibit that
action.
The feature or action cannot be
completed at this time because:
1. The disc’s software restricts it.
2. The disc’s software doesn’t support
the feature (e.g., angles)
3. The feature is not available at the
moment.
4. You’ve requested a title or chapter
number that is out of range.
-25-
128-7092
25 of 28
SOLUTION
PROBLEM
Picture is
distorted
• The disc might be damaged. Try
another disc.
• It is normal for some distortion to
appear during forward or reverse
scan.
No forward or
reverse scan
• Some discs have sections that
•
prohibit rapid scanning or title and
chapter skip.
If you try to skip through the warning
information and credits at the
beginning of a movie, you won’t be
able to. This part of the movie is often
programmed to prohibit skipping
through it.
-26-
128-7092
26 of 28
Replacement Parts
Remote Control
136B3652
Specifications
LCD Backlighting
Edge Light Tube
Resolution
800 x 480
Pixels
1,152,000
Operation Temperature
32 -140º F (0 - 60º C)
Storage Temperature
-4 - 176º F (-20 - 80º C)
Backlight life
10,000 Hours
Video Display System
NTSC / PAL
Headphone Audio Output
0.03W @ 32 ohms
Video Output
1.0Vp-p @ 75 ohms
Power Source
12V DC
-27-
128-7092
27 of 28
12 MONTH LIMITED WARRANTY
Applies to Audiovox Mobile Video Products
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail purchaser of this product that should this product or any part
thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase,
such defect(s) will be repaired or replaced with reconditioned product (at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated
bill of sale), specification of defect(s), transportation prepaid, to the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred
for installation, removal or reinstallation of the product, or to damage to tapes, discs, speakers, accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR
THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY
OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 24
MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or
representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage
so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
U.S.A. : AUDIOVOX ELECTRONICS CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 " 1-800-645-4994
CANADA : CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
For Customer Service
Visit Our Website At
WWW.audiovox.com
Product Information, Photos,
FAQ’s Owner’s Manuals
© Copyright 2004 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788
128-7092
128-7092
28 of 28