INSTALLATION AND
PROGRAMMING GUIDE
9651
HARDWIRED CONTROL
PANEL
9651 Hardwired Control Panel Installation and Programming Guide
© Cooper Security Ltd. 2004
Every effort has been made to ensure that the contents of this book are correct. However, neither the authors nor Cooper Security
Limited accept any liability for loss or damage caused or alleged to be caused directly or indirectly by this book. The contents of this book
are subject to change without notice.
Printed and published in the U.K.
Part number 496929 Issue 2
Contents
1. INTRODUCTION.......................................................................................... 3
Operator Controls and Displays - 9930 ..........................................................................................................4
System Features.............................................................................................................................................5
Detectors ......................................................................................................................................................5
User Control .................................................................................................................................................5
2. Technical Description ................................................................................ 6
Specification ...................................................................................................................................................6
Power Supply ...............................................................................................................................................6
Outputs .........................................................................................................................................................6
Inputs............................................................................................................................................................6
Fuses............................................................................................................................................................6
Control Unit PCB ............................................................................................................................................7
3. INSTALLATION ........................................................................................... 8
Overview.........................................................................................................................................................8
Cabling Keypads ............................................................................................................................................8
Fitting the System...........................................................................................................................................9
Fitting the Control unit Case.........................................................................................................................9
Fitting a 9930 Keypad ..................................................................................................................................9
Wiring the Control Unit .................................................................................................................................11
Cable Entries ..............................................................................................................................................11
Mains Connection.......................................................................................................................................11
Remote Keypads ........................................................................................................................................12
Connecting Keypads, Exit Terminate Buttons, Lock Switches and Sounders..............................................................12
Detector Circuit Connections......................................................................................................................13
Using Programmable Outputs ....................................................................................................................14
Wiring Keyswitches ....................................................................................................................................15
Fitting a Plug-by Communicator .................................................................................................................16
Fitting a Battery ............................................................................................................................................18
Initial Start Up ...............................................................................................................................................18
4. Programming ............................................................................................ 20
Entering Programming Mode........................................................................................................................20
Programming Commands.............................................................................................................................20
Leaving Programming Mode ......................................................................................................................24
Engineer Reset...........................................................................................................................................24
Re-entering Programming Mode ................................................................................................................25
Restoring the Access Codes (1st stage reset)...........................................................................................25
Restoring All Factory Default Programming...............................................................................................25
Programming Command Reference.............................................................................................................26
0: Country Defaults.....................................................................................................................................26
01 - 08 : Zone Programming ......................................................................................................................26
20: Change Engineer Code........................................................................................................................30
21: Zone Configuration...............................................................................................................................31
22: Loudspeaker Chime .............................................................................................................................31
23: RedCare Reset.....................................................................................................................................31
25: Continuous Sounder.............................................................................................................................31
27: Exit Fault External Sounders................................................................................................................31
28: Status Display.......................................................................................................................................32
29: Entry Alarm Delay Time .......................................................................................................................32
30: Silent or Audible PA .............................................................................................................................32
31: Zone Tamper Reset .............................................................................................................................32
33: System Reset .......................................................................................................................................33
34: PA Reset ..............................................................................................................................................33
35: First Circuit Response ..........................................................................................................................33
36: Alarm Abort...........................................................................................................................................33
37: Daytime Tamper Communication.........................................................................................................33
38: System Tamper Reset..........................................................................................................................34
496929
Page 1
Contents
39: Level A Exit Mode.................................................................................................................................34
40: System Auto Re-Arm............................................................................................................................35
41: Bell Delay .............................................................................................................................................35
42: Bell Duration .........................................................................................................................................35
43: Level A Entry Time ...............................................................................................................................35
44: Level A Exit Time..................................................................................................................................35
45: Entry/Exit Tone Volume........................................................................................................................35
46: Tamper Alarm Annunciation.................................................................................................................36
50: CSID Code ...........................................................................................................................................36
51: Setting Time and Date..........................................................................................................................36
52: Omit Tamper Allowed ...........................................................................................................................37
53: Abort Reset...........................................................................................................................................37
59: Sounder Tamper.................................................................................... Error! Bookmark not defined.
60: Level B Final Exit Operation.................................................................................................................37
61: Level B Entry Route Response ............................................................................................................37
62: Level B Exit Mode.................................................................................................................................38
63: Level B Alarm Response ......................................................................................................................38
64: Level B Entry Time ...............................................................................................................................38
65: Level B Exit Time..................................................................................................................................38
70: Level C Final Exit Operation.................................................................................................................38
71: Level C Entry Route Operation ............................................................................................................39
72: Level C Exit Mode ................................................................................................................................39
73: Level C Alarm Response......................................................................................................................39
74: Level C Entry Time ...............................................................................................................................39
75: Level C Exit Time .................................................................................................................................39
76: Level D Exit Mode ................................................................................................................................39
77: Level D Alarm Response......................................................................................................................40
78: Level D Entry Time ...............................................................................................................................40
79: Level D Exit Time .................................................................................................................................40
81, 82, 83, : Output Programming ..............................................................................................................40
85: Burglar Communications Re-arm .........................................................................................................42
86: Dual Ply Entry Warning ........................................................................................................................43
87: Keypad Dual Key Alarms .....................................................................................................................43
90 - 97: See “5.Testing”..............................................................................................................................44
98: Load Full Defaults.................................................................................................................................44
99: Leave Programming Mode ...................................................................................................................44
126: Select Language.................................................................................................................................45
151 - 158: Plug by Communicator Outputs ................................................................................................45
5. Testing.......................................................................................................48
Reading the Log (Command 90) ..................................................................................................................48
Keypad and Event Log Displays ................................................................................................................48
Testing Outputs (Commands 91-96) ............................................................................................................50
Engineer Walk Test (Command 97) .............................................................................................................50
Index ..............................................................................................................51
Page 2
496929
1. INTRODUCTION
The 9651 control unit is designed to be fully programmable to suit individual
site requirements and user needs. Note that in the UK the product does not
comply with the ACPO 2000 alarm policy and DD243: 2002.
The system comprises a control unit in a metal shielded case and up to four
separate keypads (see Figure 1 on the next page). You should always fit at
least one keypad.
The control unit provides:
° A four-wire bus connection for keypads.
° Connections for eight Fully Supervised Loop (FSL) zones or eight Closed
Circuit Loop (CCL) with a common tamper.
° Connections for three fully programmable outputs.
° Internal sounder loudspeaker output with electronically generated Chime,
Alarm, Fire and Entry/Exit tones. (The volume of the Entry/Exit and Chime
tones can be adjusted).
° Pins and wired harness for a plug-by communication device.
The control unit provides connectors for eight Closed Circuit (CC) zones or
eight Fully Supervised Loop (FSL) zones on its own printed circuit board.
The control unit supports the 9930 sixteen character Liquid Crystal Display
(LCD) keypad. The keypad(s) can accommodate the 934EUR-00 “Prox”
reader module to allow the end users to set and unset the system using a
“Prox” token in place of a four digit access code.
As an Installer you can program the system from the keypads. When
programming from the keypads the programming interface is arranged as a
set of three-digit numbered commands similar to those used by the 9800
family of products.
The system can provide for up to 16 separate users. User facilities include:
° Four different security levels (full and three part sets) on the 9651. The
levels can be programmed by the Installer.
° User programmable Duress code.
° Keyswitch setting/unsetting.
° Dual key PA alarm from the keypads.
Setting, unsetting & resetting using a “Prox” token
Before attempting to program the system, make sure you are completely
familiar with the functions of the system and its programmable options.
496929
Page 3
3. Introduction
1 - Control unit
2 - Keypads
3 - PIRs
4 - Door contacts
5 - fused mains spur
Figure 1. 9651 System Layout
Operator Controls and Displays - 9930
Figure 2. 9930 Remote Keypad.
The 9930 keypad has a 32 character LCD display that shows "first to alarm"
information, level status, and programming commands. In addition there are
three LEDs with the following functions:
Page 4
496929
3. Introduction
a
Glows steadily when mains power is present. Flashes when the
system is working from battery backup.
f
Glows steadily if a telephone line fault is present.
s
Glows steadily if:
a) A fault or tamper circuit is active while the system is unset.
b) The system needs an engineer or remote reset.
c) A telephone line fault is present.
The 9930 keypad provides the following keys:
9
Used to start a test of the detectors.
8
Used to start a test of the sounders and strobe.
7
Used to enable or disable the Chime facility.
6
Used to set the internal clock calendar, which provides a time stamp
on printed log entries.
5
Used to display the log (250 events).
4
Used to change the user access codes.
Y
Used to enter programming and setting/unsetting commands.
X
Used to set the system with individual zones (including 24 hour
zones) temporarily omitted.
ABCD Level setting keys. Level A sets the whole system.
System Features
Detectors
The control unit provides connections for up to eight separate detector
zones. Each zone can be connected as a two wire FSL or a four wire CC with
global tamper. See "4. Programming - Programming Commands" for the
factory default settings and instructions on how to change the zone types and
attributes.
User Control
The control unit provides 16 independent user access codes and or
Scantronic “Prox” tags . The user can change these codes or add or delete
“Prox” tags at any time, but cannot program the system with these codes. The
user can set the system in the following modes:
Full Set
All the zones function as programmed during installation.
Part Set B, C & D Selected zones are omitted. You must program the
zones to be omitted during installation.
Set with Omit
One or more zones temporarily omitted. The user selects
the zones to be omitted before setting.
496929
Page 5
2. Technical Description
Specification
Environmental
EN50131 “Class II”
Dimensions
-10° to +40 °C.
75 % RH.
Junior combi box: 243mm W, 234mm H,
87mm D
Weight
Junior combi box: 2.45 kg (without standby
battery)
Internal Clock
±10 minutes over one year (depending on the
accuracy of the mains supply frequency).
Conforms to BS4737 1986 Part 1. for Audible or Remote signalled systems.
Designed to fulfil the requirements of a EN 50131-1 Grade 2 Intruder Alarm
System.
Power Supply
All currents accurate to ±5%.
System power supply
Control unit power
9930 Remote Keypad
Standby Battery
Power Supply
230VAC +/- 10% (ambient Temp. 20°. C)
1.0A total.
115mA nominal quiescent, 150mA active.
20mA quiescent, 35mA with keypad backlight
on.
12 Volt, 7.0AH rechargeable lead-acid, Gel
Type battery (not supplied).
Type A power supply designed to fulfil the
requirements of EN 50131-1 Grade 2.
Outputs
O/P 1, 2, 3
LS
AUX
Coms OP1-8
3 open collector transistor outputs, 500mA,
12VDC, negative applied.
Can support two parallel connected externally
mounted 16 Ohm loudspeakers for internal
sounder or EE tones.
500mA maximum, 12VDC.
12V logic outputs, -ve applied in alarm (+ve
removed).
Inputs
TR
Tellback/RedCare reset*
Line Fault input
= Tamper return for bell.
= +12V applied to operate reset.
= +12V applied to indicate line failure.
Fuses
F1 - 12V AUX
1A Fast.
F2 - Battery
2A Fast.
Caution: When replacing fuses use the ratings quoted above.
Page 6
496929
2. Technical Description
Control Unit PCB
Figures 3 show the layout of the 9651control unit PCB.
12V AUX
F-1A
12
11
10
BATT F-2A
1
9
8
2
7
3
6
4
5
1. Outputs.
2. Aux power.
3. Tamper switch.
4. Zone connectors.
5. Keypad bus.
6. Communications Outputs.
7. NVM Reset pins.
8. Battery connector.
9. Battery fuse.
10. Kick start pins.
11. 21VAC from transformer.
12. 12V AUX fuse.
Figure 3. 9651 Control Unit PCB Layout
496929
Page 7
3. INSTALLATION
Overview
A typical installation comprises the following main steps:
1. Carry out a Risk Assessment of the premises and agree a security grade
for the proposed alarm installation. Decide on positions for wired
detectors, control unit, keypads, external and internal sounders. As part
of the site survey ask the user what facilities they require .
3. Ensure that there is a suitable mains supply present at the site of the
control unit.
4. If you are going to use a communication device (for example a Speech
Dialler) arrange for a PTT (Public Telephone and Telegraph) connection
point near to the control unit.
5. Install the wired detectors and run cables to the control unit. Connect
each detector to its cable.
7. Run cables from the keypads, external and internal sounders to the
control unit.
8. Install keypads and connect them to their cabling. Ensure that each one
has the correct address setting.
9. Install internal and external sounders and connect them to their cabling.
10. Install the control unit and connect it to the mains supply cabling. Do not
apply power at this point.
11. At the control unit, complete all connections to keypads, and sounders.
12. Apply power and program the control unit.
13. Test that the alarm system functions as required.
14. If required, install a communication device (for example a Speech
Dialler), connect it to the PTT network, and check that it functions
correctly.
15. Hand the system over to the user and instruct them in its use.
Cabling Keypads
Cooper Security recommend that you use a minimum 4-core 7/0.2 alarm
cable for wiring keypads.
You can connect the keypads in either a star or bus configuration. If you are
intending to use long cable runs then Cooper Security recommend that you
use star wiring with no more than 300m of cable total for the keypad wiring.
The maximum length of any one run from control unit to the most remote
keypad depends on the number of items connected to the cable. You can
double the maximum length by using two cores each for the 0V and 12V
terminals or by using 16/0.2 cable. The table below shows the maximum
Page 8
496929
3. Installation
recommended cable lengths in metres for 7/0.2 cable, assuming that you
connect all items at the end of a single cable run. In real life you may be able
to improve on these figures by spreading items along the cable length.
7/0.2 8-core cable
Length (m)
No items
1 core
2 cores on 0V
and 12V.
One
200
—
Two
100
200
Three
65
130
Four
50
100
It is possible to extend the keypad cable run by using additional power
supplies, but only up to a recommended maximum of 300m
When carrying out the cabling there are two important points to remember:
1. Do not connect anything other than keypads to the keypad bus. The
keypad bus power supply is limited to a maximum of 400mA and can supply
no more than a maximum of four keypads.
2. Make sure that the voltage between 0V and 12V of the keypad bus at the
furthest point from the control unit is at least 12.0VDC when all the keypad
backlights are on.
Note: The following instructions assume that you have already run all the
necessary cabling.
Fitting the System
Fitting the Control unit Case
1.
2.
3.
4.
Remove the control unit case from the packing.
Remove the front screws and slide off the case lid.
The upper part of the case back provides a central keyway. Mark and
drill a hole for the keyway. Temporarily fix the case back to the wall. Now
mark the position of two more fixing holes, remove the case back and
continue to drill the holes.
Refit the case back to the wall using not less than 30mm x No 8 Dome or
Pan-head screws.
Fitting a 9930 Keypad
The backplate of the 9930 keypad contains an adjustable cam that you can
use to make sure the tamper switch will operate correctly when the keypad is
mounted on an uneven surface. Figure 4 shows the backplate and the
position of mounting holes.
496929
Page 9
3. Installation
1
1
2
1
1
1. Fixing hole.
2. Adjustable cam.
Figure 4. Backplate of the 9930 Keypad
Cooper Security recommend that you mount the keypad using No 8 or 6
screws (M4/M3.5) as follows:
1. Select which cable entry you are going to use and break out the
appropriate plastic sections.
2. Hold the backplate in place against the wall and mark the position of the
centre hole in the adjustable cam (see Figure 4).
3. Drill and plug the hole, and screw the backplate to the wall through the
adjustable cam. Do not tighten the screw completely home.
4. Make sure the backplate is level and mark, drill and plug at least two
other fixing holes. Screw the backplate to the wall through the fixing
holes.
5. Cut the plastic webs connecting the cam to the remainder of the base
plate.
Note: If you do not cut the webs then the tamper switch will not operate if the
complete keypad is forced off the wall.
6.
8.
9.
Mount the front of the keypad (containing the keypad pcb) onto the
backplate and make sure that the tamper switch operates.
If the tamper switch does not operate then rotate the cam until the
tamper switch operates correctly when the front of the keypad is
mounted on the backplate.
If the “Prox” reader and tags are required, follow the installation
instructions in the separate guide supplied with the 934EUR-00 Prox
reader.
Page 10
496929
3. Installation
Wiring the Control Unit
Cable Entries
The control unit case back provides several cable entries. The back is
designed to stand away from the wall to leave space for cables.
Mains Connection
The control unit must be permanently connected to a 3A fused spur outlet
fitted with a readily accessible disconnect device. Connect the mains supply
to the control unit using the 3-way terminal block located in the control unit
back. Secure the mains cable to the case anchor point using the cable tie
provided. Note that the control unit has a T-250mA internal mains fuse. All
electrical connections should be carried out by a qualified electrician and must
comply with the current IEE Wiring Regulations: 16 Edition, Appendix 5 Standard Circuit Arrangement.
To Control Panel
Transformer
L
N
230V ~50Hz 200mA
T 250mA 250V
Figure 5. Mains Connection
Connect the 21VAC lead from the mains transformer to the main pcb. See
Figures 3 for the location of the 21VAC connector.
Caution: Do not apply mains power at this point. Do not work inside the
control unit case when mains power is present.
496929
Page 11
3. Installation
Remote Keypads
Keypad Addressing
The control unit is supplied with one remote keypad. If you have fitted more
keypads then each one must be given a separate "address". Links LK2 to LK4
set the keypad address, as shown in Figure 6.
Keypad 1
Address
Keypad 2
2
2
2
3
3
3
4
4
4
Keypad 3
Keypad 4
2
2
3
3
4
4
ON
BACKLIGHT
ON
BACKLIGHT
Backlight ON
ON
BACKLIGHT
Backlight OFF
Figure 6. Keypad Addressing.
Keypad Backlight
When supplied from the factory the control unit is configured with the keypad
backlight ON. To turn the keypad backlight OFF remove the jumper from the
"ON BACKLIGHT" link, shown in Figure 6.
Connecting Keypads, Exit Terminate Buttons, Lock Switches
and Sounders
Figure 7 shows the connections for any of the remote keypads.
To connect an exit terminate button use the "ET" connector terminals on the
keypad PCB.
Use the "ET" connector terminals to connect a Lock Switch. If using a lock
switch do not connect any other device to the "ET" terminals.
Note The lock switch must be closed circuit when the lock is unlocked.
Figure 7 shows the connections for the internal and external sounders.
Page 12
496929
3. Installation
Typical internal Sounder
16Ohm loudspeaker
(2 Max in parallel)
Bell Strobe
Typical SAB
9651 Control
Unit
+ve
-ve
OP1
OP2
OP3
TR
+
LS
12V AUX
12V AUX
0V
0V
Bell
-ve Hold Off
-ve Tamper Return
+ve Hold Off
-ve Apply Trig
9930 Keypad
0V 12V CLK DATA ET
Lock Switch
OR
Exit terminate button
(NO, push to make)
9651 Control
Unit
0V 12V CLK DATA
To other
keypads
4-core
Fig 7. Keypad and Sounder Connections
Detector Circuit Connections
The left hand edge of the main PCB provides 14 connectors that can be used
for up to 8 FSL or 8 CCL zones. During programming use command 21 to
configure these connectors as either CCL zones or two wire FSL zones.
Closed Circuit Zones
Figure 8 shows how to connect CCL zones. Note that there is a single Global
tamper loop that serves all zones.
Tamper loop
Global Anti-tamper
Zone 1
Zone 2
Alarm contacts
Zone 1
Alarm contacts
1
2
Zone 3
Zone 4
3
Zone 5
Zone 6
Zone 7
Zone 8
Zone 2
Figure 8. Closed Circuit Connections
496929
Page 13
3. Installation
FSL Connections
The control unit zone connectors provide space for up to eight FSL zones.
Each FSL zone is a ‘Fully Supervised Loop’ using a two wire closed loop. The
loop uses two resistors of different values to differentiate between ‘Circuit’ and
‘Tamper’ signals: a 2K2 resistor fitted in series at the end of the wired loop,
and a 4K7 resistor fitted across the alarm contact, see Figure 9.
With the loop in a normal state and the alarm contacts closed (shorting out the
4K7 resistor), the total resistance of the loop is 2K2. When the alarm contacts
open (removing the short from the 4K7 resistor) the resistance of the loop
increases to 6K9 and the control unit detects an alarm condition. If a tamper
device opens then the loop resistance will be open circuit and the control unit
detects a tamper signal.
To connect a detector to an FSL loop you must wire suitable resistors to the
detector. Always check resistor colour coding before wiring resistors into
circuit, see Figure 10.
The wiring resistance of the cable to the detector (including joints) should be
restricted to a maximum of 100 ohms. The recommended maximum cable
distance per zone is 200 - 300 metres.
4K7
Alarm contacts
2K2 EOL
Zone 1
Tamper contacts
4K7
1
2
Zone 2
Alarm contacts
2K2 EOL
Tamper contacts
Figure 9. FSL Connections
4k7
Yellow
Violet
Red
Gold
2k2
Red
Red
Red
Gold
Figure 10. Resistor Colour Code for FSL Resistors
Note: You can leave the global anti-tamper connectors unlinked if you are
using FSL wiring.
Using Programmable Outputs
In the 9651 OP1, 2 and 3 are "pull down type" outputs that provides negative
applied control signals. If necessary use command 159 to invert the output
polarity.
Page 14
496929
3. Installation
To program the outputs use programming command 81 for OP1, command 82
for OP2 and command 83 for OP3 (see "4. Programming"). Figure 11 shows
some example applications for OP3
Shock Sensor Reset
0V
VIPER
OP3
OP3
OP3
OP2
OP2
OP1
OP1
OP1
12V
12V
12V
+ve
PIR Set Latch/Walk Test
Bell Follow Buzzer/Relay
BUZZER/RELAY
PIR
OP2
0V
0V
0V
TR
TR
TR
+
+
+
LS
LS
LS
12V AUX
12V AUX
12V AUX
12V AUX
12V AUX
12V AUX
0V
0V
0V
0V
0V
0V
Use Command 83 4
Use Command 83 0
Relay energises/buzzer sounds
when bell activates.
For:
Set Latch use Command 83 3
Walk Test use Command 83 5
Figure 11. Wiring Examples for Programmable Output OP3
Wiring Keyswitches
To allow a user to set and unset the system using a keyswitch, connect a
fixed position or spring loaded (momentary) key switch to a zone input. Note
that a key switch cannot reset the system. When programming the control unit
select zone type (KM) for momentary or (KF) for fixed position keyswitches.
Figure 12 shows the connections for a keyswitch.
Fixed Keyswitch (KF)
Keyswitch
CC
FSL
System
CC Wiring
CCT(n)
OFF
Closed
2k2
Unset
ON
Open
6k9
Set
4k7
Momentary Keyswitch (KM)
Keyswitch
CC
FSL
System
FSL Wiring 2k2
CCT(n)
Operate
Close-Open- 2k2-6k9-2k2
Unset
Close
Operate
Close-Open- 2k2-6k9-2k2
Set
Close
Figure 12. Connecting a Keyswitch
496929
Page 15
3. Installation
Fitting a Plug-by Communicator
The 9651 can be fitted with a communicator or speech dialler, for example the
Scantronic 660, 8400, and 8440 digital communicators or the SD1 or SD2
Speech diallers. To fit a communicator inside the control unit, follow the
instructions below. To connect an SD1 or SD2 follow the instructions provided
with those products.
Caution: Follow the instructions in the order shown, or you may damage
the control unit and/or communicator.
1. Disconnect mains and battery power from the control unit and remove
the case lid, if the system has already been installed.
2. Detach the main PCB from the support pillars in the control unit case,
and lift the PCB carefully to the left.
3. Fit the communicator between the PCB support pillars, making sure that
the main PCB can fit back into position (see Figure 13).
Figure 13. . Fitting a Plug By Communicator in a Junior Combi Box.
4.
Make any necessary connections from the communicator to the Comms
Wiring Harness. Figure 14 shows the outputs available on the free ends
of the Comms Wiring Harness.
Page 16
496929
3. Installation
Com Connector Cable, Part No. 485210
Comms O/P1 (Brown) -ve applied (+ve removed) in alarm
Comms O/P2 (Orange) -ve applied (+ve removed) in alarm
Comms O/P3 (Yellow) -ve applied (+ve removed) in alarm
Comms O/P4 (Green) -ve applied (+ve removed) in alarm
Comms O/P5 (Blue) -ve applied (+ve removed) in alarm
Comms O/P6 (Purple) -ve applied (+ve removed) in alarm
Comms O/P7 (White) -ve applied (+ve removed) in alarm
Comms O/P8 (Grey) -ve applied (+ve removed) in alarm
Line Fail input (White/Brown) +12V applied to indicate telephone line fail.
Tell Back input (White/Orange) +12V appied to change from engineer to customer reset.
0V (Black)
12V (Red)
Figure 14. Communications Wiring Harness.
5.
6.
Plug the Comms Wiring Harness onto the communications connector on
the main PCB (see Figure 3).
Re-fit the PCB to the support pillars. Secure the PCB to the support
pillars with the screws provided (Figure 15). Make sure that the bottom
left corner of the PCB is seated on its support pillar.
Figure 15. Fitting Control Unit PCB.
If the system has already been installed:
7. Re-connect the battery.
8. Fit the case lid.
9. Apply mains power.
10. Test communicator operation (see programming commands 151 to 158).
496929
Page 17
3. Installation
Fitting a Battery
Fit a rechargeable battery into the back of the case. The case provides space
for a 12V 7AH battery. Make sure the battery terminals are oriented in the
position shown in Figure 16.
7AH
Figure 16. Fitting a Battery
Initial Start Up
Before applying power to the control unit, ensure that:
• All remote keypads have been addressed and connected.
• All external and internal sounders are connected.
• All wired zone circuits are connected.
Then:
1. Connect the battery to the control unit PCB.
2. Briefly short the kick start pins together (they are located above battery
connector, see Figure 3).
The green power LED on the keypad flashes and the internal sounder
may sound. Ignore any display at this stage.
3. Key-in the factory default user access code: 1234.
The internal sounder stops. Ignore any display at this stage.
4. Please fit the case lid before applying mains power (this also defeats the
tamper switch).
5. Apply mains power.
Page 18
496929
3. Installation
The power LED on the keypad glows steadily.
6.
Key-in 0 followed by the factory default engineer access code: 7890.
(You do not have to remove the control unit lid.)
The display shows:
Installer Mode
You are now in programming mode.
Carry on to Chapter 4 in order to program the system.
496929
Page 19
4. Programming
Entering Programming Mode
Installation - Initial Power Up” describes how to enter programming mode for
the first time in a new installation. If you wish to enter programming mode at
any other time:
1. Make sure the system is unset.
2.
Press 0, then key in the Engineer’s code (default 7890).
The display shows:
You are now in programming mode.
Installer Mode
While the system is in programming mode all keypads except the one you are
using will be locked, displaying “Busy”.
Programming Commands
When delivered from the factory the control unit already has default program
settings. To change the default programming you must be in programming
mode. Then:
1. Key in the appropriate Command number and press Y.
The display shows the current value of the Command.
2.
Key in digits to select the value you require.
The display shows the new value.
3. Press Y to store the new value of the Command.
If at any time you change your mind, repeat step 1 to 3. The table on the
following pages shows the Commands and their options. ( A “Y” next to a
Command value shows that it is the factory default.)
The factory default access codes are:
Engineer Code
7890
Access Code User 1
1234
Access Code Users 2 to 16 X 002 .... X 016 (inactive)
Duress Code
X017 (inactive)
Note: The factory default Access Codes 02 to 16 and the Duress Code must
be changed by USER 1 to a four digit number to activate them. See
“9651 User Guide” for a more detailed explanation of changing user
access codes.
Page 20
496929
4. Programming
Command
0
n=
Country PTT Defaults
country, one of:
0 = UK (Y)
1 = Italy
2 = Spain
3 = Portugal
4 = Netherlands
5 = France
6 = Belgium
7 = Germany
8 = Switzerland
9 = Austria
X1 = Ireland
X2 = OEM 1
X3 = OEM 2
X4 = OEM 3
X5 = Norway
X6 = Denmark
X7 = Sweden
Note: If you carry out this Command
then the system will load all defaults for
the selected country.
Key in:
Zone Configuration
0 Close Circuit
1 Fully Supervised Loop
21YnY
Y
22
LS Chime Output
Loudspeaker chime volume
0 Off ( Keypad only)
1 low, 9 = max
22YnY
23
RedCare Reset
0 Off
1 On
23YnY
Y
25
Internal Sounder
0 LS Timed (Follows external bell)
1 Continuous
25YnY
Y
27
Exit Fault External Sounder
0 Internal
1 Local
27YnY
Y
28
Status Display
28YnY
0 Panel status visible all the time
Y
1 Panel status hidden 180s after setting
2 Display for 30 s on valid access code entry
29
Entry Alarm Delay Time
0 Delay off
1 Delay on
29YnY
Y
30
PA Response
0 Audible
1 Silent
30YnY
Y
31
Zone Tamper Reset
0 Engineer reset off
1 Engineer reset on
31YnY
33
System Reset
0 Eng reset off
1 Eng reset on
33YnY
Y
34
PA Reset
0 PA cust reset
1 PA eng reset
34YnY
Y
35
First Circuit Lockout
0 Lock out on
1 Re-arm
35YnY
Y
36
Alarm Abort
0 Abort off
1 Abort on
36YnY
Y
37
Day Tamper Comms
0 Day Tamper off
1 Day Tamper on
37YnY
Y
38
System Tamper Reset
0 Customer Reset
1 Engineer Reset
38YnY
39
Level A Exit Mode
0 Timed
1 Terminated
2 Final door
3 Lock Set
39YnY
Y
40
System Auto Re-Arm
0 Rearm Never
1 Rearm 1
2 Rearm 2
3 Rearm 3
4 Rearm Always
40YnY
Y
0YnY
01 - 08 Zone nn
nnYYab
nn = zone number 01 to 08
Note: For zones 1 to 8 key in “01” to
“08”.
a=
Zone type, one of:
00 = NU (not used)
01 = PA (panic alarm)
02 = FR (fire zone)
03 = NA (normal alarm)
04 = 24 (24 hour zone)
05 = FE (final exit)
06 = ER (entry route)
07 = SA (Shock Analyser)
08 = TC (Technical)
09 = KB (Keybox)
10 = SD (Smoke detector)
11 = KM (Key switch momentary)
12 = KF (Key switch latched)
13 = AM (Anti mask)
14 = FB (forbikobler zone)
b = Zone attributes, any of:
X1 = C (chime)
X2 = S (soak test)
X3 = D (double knock)
X4 = O(Omit allowed)
B = b (armed in Level B)
C = c (armed in Level C)
D = d (armed in Level C)
X7 = Shock Analyser sensitivity (enter
a number in the range 1 (lowest) to 6
(maximum)
(default)
Z01=FEbcd
Z02=Erbcd
Z03-Z07=Nabcd
Z08=PA
Example: Zone 07 is a Normal Alarm, active
in Part Set B, Omit Allowed. Type in:
03 Normal Alarm
B Active in Part Set B
X4 Omit Allow
Y to store the value of the Command.
20
Engineer Code
nnnn = New engineer code
21
5
Y
20YnnnnY
7890
496929
Page 21
4. Programming
41
42
43
44
45
46
Bell Delay
0 No delay
1 1.5 minutes
2 3 minutes
3 5 minutes
4 10 minutes
5 15 minutes
6 20 minutes
41YnY
Y
Bell Duration
1 1.5 minutes
2 3 minutes
3 5 minutes
4 10 minutes
5 15 minutes
6 20 minutes
42YnY
Level A Entry Time
1 10 Seconds
2 20 seconds
3 30 seconds
4 45 seconds
5 60 seconds
6 120 seconds
43YnY
Level A Exit Time
1 10 Seconds
2 20 seconds
3 30 seconds
4 45 seconds
5 60 seconds
6 120 seconds
44YnY
Entry/Exit Volume
0 No Entry/Exit tones from Loudspeaker
n EE tone volume from LS (1=low,
9=max)
45YnY
Tamper Alarm Response
0 Internal sounders
1 Keypad sounders
2 Internal and keypad sounders
46YnY
50
CSID Code
n....n = Seed code for remote reset
Level B Alarm response
0 Keypad sounder Only
1 Internal sounder and keypad
sounders
2 Local (all sounders, no comms)
3 Full alarm (all sounders and comms)
63YnY
Level B Entry Time
1 10 seconds
2 20 seconds
3 30 seconds
4 45 seconds
5 60 seconds
6 120 seconds
64YnY
Level B Exit Time
1 10 Seconds
2 20 seconds
3 30 seconds
4 45 seconds
5 60 seconds
6 120 seconds
65YnY
70
Level C Final Exit Operation
0 C=FE = FE (Final exit)
1 C=FE = NA (Normal alarm)
70YnY
Y
71
Level C Entry Route
0 C=ER = ER (Entry route)
1 C=ER = FE (Start entry timer)
71YnY
Y
72
Level C Exit Mode
0 Timed plus low tone (default)
1 Instant set
2 Silent set (kpd beeps at end of
setting period)
3 As Level A
72YnY
73
Level C Alarm Response
0 Keypad sounder only
1 Internal sounder and keypad
sounders
2 Local (all sounders, no comms)
3 Full alarm (all sounders and comms)
73YnY
Level C Entry Time
1 10 seconds
2 20 seconds
3 30 seconds
4 45 seconds
5 60 seconds
6 120 seconds
74YnY
75
Level C Exit Time
1 10 Seconds
2 20 seconds
3 30 seconds
4 45 seconds
5 60 seconds
6 120 seconds
75YnY
Y
76
Level D Exit Mode
0 Timed plus low tone (default)
1 Instant set
2 Silent set (kpd beeps at end of
setting period)
3 As Level A
76YnY
77
Level D Alarm Response
0 Keypad sounder only
1 Internal sounder and keypad
sounders
2 Local (all sounders, no comms)
3 Full alarm (all sounders and comms)
77YnY
64
Y
65
Y
Y
Y
Y
Y
5
Y
50Yn....nnY
none
51
Set Time and Date
see “Setting Time and Date”
52
Omit Tamper Allowed
0 Alarm contacts only
1 Alarm plus tamper contacts
52YnY
Y
53
Abort reset
0 Abort System
1 Abort User
53YnY
Y
60
Level B final exit operation
0 B=FE = FE (Final exit)
1 B=FE = NA (Normal alarm)
60YnY
Y
61
Level B Entry route
0 B=ER = ER (Entry route)
1 B=ER = FE (Start entry timer)
61YnY
Y
62
Level B Exit Mode
62YnY
0 Timed plus low tone
Y
1 Instant set
2 Silent set (kpd beeps at end of setting period)
3 As Level A
Page 22
63
74
51Y
496929
Y
Y
Y
4. Programming
78
79
81
Level D Entry Time
1 10 seconds
2 20 seconds
3 30 seconds
4 45 seconds
5 60 seconds
6 120 seconds
78YnY
Level D Exit Time
1 10 Seconds
2 20 seconds
3 30 seconds
4 45 seconds
5 60 seconds
6 120 seconds
79YnY
Output 1 Type, one of
81YnY
Output 2 Type, one of
See Command 81 for a list of options.
Default for Command 82 is 08 Strobe.
82YnY
83
Output 3 Type, one of
See Command 81 for a list of options.
Default for Command 83 is 03 Set
latch.
83YnY
85
Burg Comms Rearm
85YnY
93
Test Output 3 See “5. Testing”
Output 3 operates, press X or Y to end
test.
93Y
94
Test Internal Sounder (Single
System Only) See “5. Testing”
Internal sounders operate, press X or
Y to end test.
94Y
95
Test Kpd Sounder See “5. Testing”
Keypad sounders operate, press X or
Y to end test.
95Y
97
Engineer Walk Test See “5. Testing”
Zn indication and chime operate when
cct open
Y (Clear) End walk test
97Y
98
Load Defaults
99
Leave Programming
126
nn =
Language
0 = English(Y)
1 = Italian
2 = Espanol
3 = Portugu
4 = Nederl
5 = Francai
6 = Deutsch
7 = Norsk
8 = Svenska
9 = Dansk
126YnnY
151
nn
Plug by Comms Output 1
00 Not Used
01 Fire (default)
02 PA
03 Burglar
04 Open/Close
05 Alarm Abort
06 Technical Alarm
11 AC Fail
12 Tamper Alarm
13 Open
14 Close
15 Zone Omitted
16 Medical
17 Key-Box
18 Anti-Mask
19 Smoke Detector
30 Set o/p 1
31 Set o/p 2
32 Set o/p 3
33 Set o/p 4
34 Unset o/p 1
35 Unset o/p 2
36 Unset o/p 3
37 Unset o/p 4
151YnnY
152
Plug by Comms Output 2
Default 02 PA. See Command 151
152YnnY
153
Plug by Comms Output 3
Default 03 Burglar. See Command 151
153YnnY
154
Plug by Comms Output 4
154YnnY
Default 04 Open/Close. See Command 151
155
Plug by Comms Output 5
155YnnY
Default 15 Zone Omitted. See Command 151
156
Plug by Comms Output 6
156YnnY
Default 05 Alarm Abort. See Command 151
Y
86
Dual Ply Entry
0 Off
1 On (not recommended in U.K.)
86YnY
Y
87
Dual Key Alarm
0 Off
1 On
87YnY
Y
90
Event Log*
0 Print log
1 View earlier events
3 View later events
X Cancel viewing
Y Toggles time/date display
90YnY
Test Output 1 See “5. Testing”
Output 1 operates, press X or Y to end
test.
92Y
Y
82
91
Test Output 2 See “5. Testing”
Output 2 operates, press X or Y to end
test.
Y
Where n is one of the following:
00 Bell (default full/part set sys.)
01 EE follow
02 Armed lamp
03 Set latch
04 Shock sensor reset
05 Walk test
06 Ready lamp
07 24 hour alarm
08 Strobe
09 Smoke sensor reset
10 French Siren Test
11 Strobe Set
12 Pulse Set o/p 1
13 Pulse Unset o/p 1
26 Pulsed Set o/p 1
27 Pulsed Set o/p 2
28 Pulsed Set o/p 3
29 Pulsed Set o/p 4
30 Pulsed Unset o/p 1
31 Pulsed Unset o/p 2
32 Pulsed Unset o/p 3
33 Pulsed Unset o/p 4
0 Latch
1 Rearm
92
91Y
496929
98Y1Y
99YY
Page 23
4. Programming
157
Plug by Comms Output 7
Not used. See Command 151
157YnnY
158
Plug by Comms Output 8
Default 06 Technical. See Command
151
Invert Plug-by Comms Outputs
0= +ve removed
1 - +ve Applied
Set o/p 1 Time
Set o/p 2 Time
Set o/p 3 Time
Set o/p 4 Time
Set o/p 1 ABCD
Set o/p 2 ABCD
Set o/p 3 ABCD
Set o/p 4 ABCD
Unset o/p 1 Time
Unset o/p 2 Time
Unset o/p 3 Time
Unset o/p 4 Time
Unset o/p 1 ABCD
Unset o/p 2 ABCD
Unset o/p 3 ABCD
Unset o/p 4 ABCD
Fire o/p 1
Fire o/p 2
Fire o/p 3
Fire o/p 4
PA o/p 1
PA o/p 2
PA o/p 3
PA o/p 4
158YnnY
159
170
171
172
173
174
175
Y
Set range
01-12
seconds
Toggle
ABCD
Set range
01-12
seconds
Toggle
ABCD
Select if o/p
required to
operate if a
Fire Alarm
Select if o/p
required to
operate if a
PA Alarm
Leaving Programming Mode
When all programming has been completed:
1. Key-in ‘99 Y’ at the keypad
The display shows:
2.
99:Exit Eng ?
Press Y.
The display shows:
followed by the time and date.
99:Checking Sys
The system is now in user mode.
Note: If there is a fault, for example an open tamper circuit, the display shows
this and will not return to Day mode. Press X and rectify the faults.
Engineer Reset
To perform an Engineer Reset:
1. Check that the display is showing the alarm condition.
2. Key in 0 followed by the Engineer’s code (default 7890), followed by 99
YY.
The display shows the time and date.
Page 24
496929
4. Programming
Re-entering Programming Mode
You can go back into programming mode whenever the system is unset and
not in alarm:
1. Key in 0 followed by the Engineer’s code (default 7890).
The display shows:
You are now in programming mode.
Installer Mode
Restoring the Access Codes (1st stage reset)
If the user and/or engineer codes are lost, then:
1. First remove mains power and then open the case and disconnect the
battery.
2. Identify the NVM Reset pins and Kick Start pins on the main pcb (see
Figures 3).
3. Short the NVM Reset pins together using a small wire link. Short the Kick
Start pins together with another small wire link.
4
Reconnect the battery.
5. Remove the shorts from the NVM Reset pins and Kick Start pins.
The control unit loads the factory default access codes:
User 1: 1234, Engineer: 7890.
6.
7.
Close the control unit and apply mains power.
Carry out an engineer reset.
Restoring All Factory Default Programming
If you wish to restore all factory default options then:
1. Enter programming mode (if you are not already there).
2. Key in 98 Y at the keypad.
The display shows:
3.
4.
Load default
Press 1 Y at the keypad.
Press Y.
The keypad gives a double confirmation tone and the system loads the
factory default Command values, erasing all previously programmed
values.
Note:The log is protected and cannot be erased by the Installer.
496929
Page 25
4. Programming
Programming Command Reference
0: Country Defaults
Use this Command to select the country and PTT defaults (to select language
see Command 126).
Note: 1. If you select options X5, X6 or X7 (Norway, Sweden or Denmark)
then the control unit also changes the method of entering programming
mode. See “Entering Programming Mode” at the beginning of this
chapter.
2. This Command loads default access codes and programming options.
See “Programming Commands” for details of the options available.
01 - 08 : Zone Programming
The zone programming Commands 01 to 08 take three or more digits. The
first two digits describe the zone type, subsequent digits describe the zone
attributes.
When you key in the zone number and press Y the display shows the zone
number and any text caption for the zone. At this point you can edit the zone
text (see next page). Press Y again to start entering the zone types and
attributes. When you have entered the zone type and attributes press Y once
more to store the changes.
Zone Names
When you key in the zone number and press Y the display shows the current
zone name with a flashing cursor under the first letter. Enter letters from the
keypad one at a time by pressing a number key repeatedly until the display
shows the letter you want. You may already be familiar with typing out short
messages on a mobile phone using the same sort of system. Figure 17
shows which letters are assigned to each key. Press C to move the cursor to
the next space for a new letter.
If you make a mistake press C or D to move the cursor over the letter you
want to change, and key in the new letter. If you want to delete a name
completely press D to move the cursor under the extreme left hand character
of the name. Press D again. The display clears the old name.
The system can store a maximum of 12 characters per name, including
spaces and punctuation marks.
When you have finished entering the user name press Y.
Page 26
496929
4. Programming
Figure 17. Letters Generated by Each Number Key
Zone Types
The following types are available:
00
Not Used (NU) The system ignores Zones with this type. Key in 00 for
a zone that will not be used.
Note: If a zone is programmed as ‘Not Used’, it is not necessary to link the
circuit or anti-tamper connections.
Option Zone Type
01
Panic Alarm (PA) - Operating a device programmed as ‘Panic Alarm’
will start either a silent alarm transmission to the ARC, or an audible
alarm, depending on how you have programmed PA Response, (see
Command 30). PA alarms operate whether the system is set or unset.
02
Fire (FR) - Smoke or heat detectors connected to FR type zones
cause the speakers to give a distinctive fire signal (internal sounders
pulsing “Dee Dah Dee Dah...”). Fire alarms operate whether the
system is set or unset, and will always trigger communications if fitted.
03
Normal Alarm (NA) - A zone programmed as ‘Normal Alarm’ will start
an alarm when the system is set.
04
24 Hr Zone (24) - This zone causes an internal alarm if violated when
the system is unset, and a full alarm if the system is set. Providing the
Installer programs 24hr zones with ‘Omit Allow’, the user can omit 24
hour zones in Day mode. Note that the control unit re-instates all 24Hr
zones if anyone sets the system.
Final Exit (FE) - Zones of this type must be the last detector to be
activated on exit, or the first to be activated on entry. You can use
zones of this type to finally set the system, or to start the entry
procedure. Use Command 39 to set the exit mode type.
05
496929
Page 27
4. Programming
06
07
08
Entry Route (ER) - Use this zone type for detectors sited between the
Final Exit door/detector and a keypad. If an ‘Entry Route’ zone is
violated when the system is set, an alarm will occur. If the entry/exit
timer is running when an Entry Route zone is violated then no alarm
occurs until the entry/exit timer expires.
Shock Analyser (SA) - You can apply this zone type to zones 1 to 4
Only. This zone type can accommodate up to 4 - 5 “Inertia” type
sensors normally fitted on windows or patio doors.
(See also “Zone Attributes - Sensitivity”.)
Technical (TC) - Use this zone type when you want to monitor
equipment, for example a freezer, without raising a full alarm. If a
technical alarm zone is activated while the system is set, the system
makes no audible alarm. However, when a user unsets the system the
keypad indicates a fault. If a technical alarm zone is activated while
the system is unset then the system starts a pulsed tone from the
keypad. If programmed, the control unit also starts communication.
When a user enters a valid code the keypad stops the tone and
displays the zone.
09
Key Box (KB) - This zone type is for use in Scandinavia only. When a
zone of this type is required, the Installer connects the alarm wires of
the zone to a special external key box and the tamper wires to the
box enclosure switch. When someone opens the box the control unit
logs the event and communicates it to the ARC. The control unit also
provides a Key Box output type that you can program to trigger one of
the plug by communicator output pins, see Command 151.
10
Smoke Detector (SD) - Use this type for zones connected to 12V
smoke detectors. This type is active whether the system is set or
unset and the control unit will transmit a specific alarm to the ARC if
triggered. The control unit also provides a Smoke Detector output type
that you can program to trigger one of the plug by communicator
output pins, see Command 151.
If a zone of this type causes an alarm then the user will need to enter
an access code to disarm and reset the system.
Key Switch - There are two Key Switch zone types: Momentary and
Fixed. These two zone types are intended for use on zones that
connect to an access control keypad, electronic key or other type of
hardwired device used to set or unset the system.
When the user operates the Keyswitch while the system is unset then
the control unit starts the programmed exit mode.
When the user operates the Keyswitch while the system is set then
the control unit unsets the system immediately.
The user cannot reset the sytem from a Keyswitch zone.
Page 28
496929
4. Programming
To set Level A do not assign a Keyswitch zone to levels B, C or D. To
set any other level assign the Keyswitch zone to a single level.
11
Momentary (KM) - Use this zone type to connect a momentary
keyswitch to a single zone.
12
Fixed (KF) - Use this zone type to connect a fixed position keyswitch
to a single zone.
13
Anti-Mask Zone (AM) - Note This zone type is for use in EN50131
Grade 3 systems only and is not applicable on the 9651 control
panel.
14
Forbikobler (FB) - This zone type is a Scandinavian entry/exit zone.
Use this type on zones connected to stand alone external keypads or
access controllers. The zone operates as a normal entry/exit zone but
when triggered by the external keypad during the exit time the control
unit stops the exit time and sets the system. If the zone is triggered
while the system is set then the control unit starts the entry time.
Zone Attributes
Specific zone types can have one or more attributes programmed by the digit
after the zone Command and type. (To remove an attribute, key in the
attribute digit again.)
Option
X1
Chime (C) When enabled by the user, the system gives a non-alarm
warning tone when any zones programmed as ‘Chime’ are opened.
This facility operates only while the system is unset.
Note: 1. ‘Chime’ is available only for Normal Alarm, Final Exit, Entry Route
and Shock Analyser zone types.
2. To make chime available from the keypad sounders but not the
internal sounder then program Command 22 with option 0.
X2
Soak Test (S) Use this zone attribute if you want to place under long
term test a detector that you suspect is giving false alarms. Zones with
this attribute are disabled for 14 days after you return the control unit
to user mode. If the zone is opened while the system is set then the
Service LED glows and the control unit logs the event as a “Soak Test
Fail Zn” (n is the zone number) without sounding any bells or starting
signalling. The Service LED stays alight until the Engineer resets the
system. After midnight on the 14th day the control unit returns the
zone to normal use.
Note: Soak test is available only for Normal Alarm, Entry Route, Technical
and Shock Analyser zone types.
496929
Page 29
4. Programming
X3
Double Knock (2) Zones with this attribute will cause an alarm
condition only if one or more sensors generate two alarms events
within a five minute time window, or if one zone remains open for
more than 10 seconds. Programming a zone as ‘Double Knock’ is a
way of reducing false alarms caused by environmental changes, but is
not normally recommended.
Note: ‘Double Knock’ is available only for Normal Alarm and Entry Route
zone types.
X4
Omit Allow (O) When applied to a zone, this attribute allows the user
to omit the zone.
B
Level B When applied, the zone will be armed when the user selects
Level B.
C
Level C When applied, the zone will be armed when the user selects
Level C.
D
Level D When applied, the zone will be armed when the user selects
Level D.
X7
Sensitivity When you use this Command you must also enter an extra
digit in the range 1 to 6 in order to set the sensitivity of the shock
sensor. 1 is least sensitive, 6 is most sensitive. Note that to use this
attribute you must make one of zones 1 to 4 a shock analyser type.
To adjust the sensitivity you must enter the complete Command, for
example to change the sensitivity to 3 you must key in: X7 + 3.
20: Change Engineer Code
To change the Engineer access code:
1. Make sure you are in programming mode.
2. Key in 20 and press Y.
The display shows:
3.
20:Code
Key in a new four digit Engineer access code.
The display shows:
4.
20:Code ****
Press Y.
Page 30
496929
4. Programming
21: Zone Configuration
This Command allows you to select the wiring type of the zone connectors on
the main PCB. The options available are:
Option
0
Eight Closed circuit zones with global anti tamper on control unit.
1
Eight Fully Supervised Loop (FSL) zones on control panel.
See Chapter 3 for wiring details.
22: Loudspeaker Chime
A user may find that the chime tone from the keypads is not loud enough. If
so, then use Command 22 option 1 to make the internal sounder also give the
chime tone. To alter the volume of the tone from the internal sounder enter a
digit in the range 1 to 9. 1 is quietest, 9 is loudest. The internal sounder
demonstrates the volume of the tone when you enter the digit.
23: RedCare Reset
Option 1 enables RedCare Reset, which is designed to operate with the plugby communicator lead.
Note: You must set System Reset to Engineer (Command 33 option 1) to
ensure RedCare Reset works correctly.
After an alarm the user keys in their access code to silence the alarm, but
cannot reset the system. The first to alarm display and Service LEDs remain
visible. The user contacts the ARC, who verifies the user's identity. The ARC
sends a signal back to the control unit. The Service LED goes dark and the
end user can now reset the system with any valid access code, providing that
there are no faults.
Use option 0 (the default) to disable the function.
25: Continuous Sounder
Option 0 of this Command makes the internal sounder follow the external bell
delay and duration times. Option 1 makes the internal sounder continue after
the external bell times out.
27: Exit Fault External Sounders
When programmed with option 0 the system operates the internal sounders if
the user tries to exit while a zone is still violated (for example a door is not
shut). When programmed with option 1 the system operates the external
sounders as well as the internal sounders.
496929
Page 31
4. Programming
28: Status Display
Use option 1 of this Command if you do not wish to show keypad displays
permanently. The keypad displays “Level Set” for 180 seconds after the user
sets the system and then reverts back to the time and date display. Use this
option when installing a system in the U.K.
When set to option 0 the keypad displays “Level Set” the whole time that the
alarm system is set.
Use option 2 to make the keypad display revert to time and date 30 seconds
after any event. Note that if you use this option the s and f LEDs also
operate for only 30 seconds.
29: Entry Alarm Delay Time
This Command determines what the system will do if a user strays from an
entry route zone during entry. ( If this Command is enabled, the system will
fulfil the requirements of EN 50131-1.)
Use option 0 to make the system generate an immediate alarm if the user
strays from an entry route zone during entry.
If you use option 1 and the user strays from the entry route during entry time
then the system waits until the end of the entry time and then adds 30
seconds before raising a full alarm. From the entry stray the internal sounder
will operate to alert the user that they have made a mistake and have time to
unset the system.If the user enters an access code before the end of the entry
time or within the additional 30 seconds then the user can reset the system.
30: Silent or Audible PA
This Command selects how the system responds when a PA zone operates.
Option
0
(Audible PA) The system operates the sounders and, if a
communicator is fitted, sends a PA message to the ARC.The keypad
displays the PA zone when a user disarms the system.
1
(Silent PA) The sounders stay silent. If a communicator is fitted the
system sends a PA message to the ARC.The keypad displays the PA
zone when a user disarms the system.
31: Zone Tamper Reset
Use this Command to ensure that the system complies with Scandinavian
requirements for resetting zone tamper alarms while the system is unset.
Use option 0 to allow user reset after a zone tamper.
Use option 1 to enforce engineer reset. The user can silence the alarm, but
the engineer must reset the system by entering the engineering access code,
or by using anti-code or remote reset.
Page 32
496929
4. Programming
33: System Reset
If you wish to make the system engineer reset, then use option 1. For user
reset use option 0.
Certain types of event will always need an Engineer reset, no matter what
option you choose for Command 33. These events are:
Auxilliary 12V supply fuse blown.
Keypad missing or failed.
A low battery at the control unit.
34: PA Reset
If you wish to make the system engineer reset after a PA alarm then use
option 1. For user reset use option 0.
35: First Circuit Response
If you select option 0 (Lock out) then the complete system rearms at the end
of the programmed bell run time, but excludes the first zone to activate during
the set cycle.
If you select option 1 (Re-arm) then, when an alarm occurs, the complete
system (including the first zone to activate) rearms at the end of the
programmed bell run time (providing the zone is closed). While the zone is
open, the system locks it out. If the zone closes after the system rearms, the
system reinstates it.
36: Alarm Abort
Users occasionally trigger false alarms by accident. The control unit can be
programmed to allow users to abort an alarm by enabling option 1.
If a user accidentally triggers an alarm while the system is set, then the
control unit activates Channel 3, starts the bell delay timer and alarm abort
timer. To abort the alarm the user must enter a valid access code during the
abort period. When the user successfully enters the code during the abort
period the system deactivates Channel 3 and triggers the programmed abort
channel simultaneously in order to signal a separate code abort, as required
by some ARCs.
Note: The alarm abort period is controlled by the ARC at 120 seconds.
37: Daytime Tamper Communication
This Command controls how the control unit reports tampers while the alarm
system is unset.
With option 1 selected the system communicates tamper events to the ARC
and starts the internal sounder.
With option 0 selected the system starts the internal sounder only.
496929
Page 33
4. Programming
38: System Tamper Reset
This Command allows you to choose whether the customer can reset the
system after a tamper alarm. This facility is independent of that offered by
Commands 31 and 33. If you select option 0 (customer) then the user can
reset the system after a system tamper alarm providing no fault exists. If you
select option 1 (engineer) then you must enter the engineer access code at a
keypad to reset the system after a system tamper alarm.
39: Level A Exit Mode
Use this Command to select the exit mode for Level A (Full Set).
Note: The keypads give a double beep confirmation tone at the end of all
setting modes.
Option
0
Timed. Use this option EITHER if the user completes setting the
system by pushing an exit terminate button connected to a keypad OR
if no exit terminate button is connected, and the system sets after a
delay selected using Command 44.
1
Terminate. Use this option if the user completes setting the system by
pushing an exit terminate button connected to a keypad. Note that the
exit time is infinite in this option.
2
Final door set. Use this option to complete setting the system by
closing a door fitted with a Final Exit zone detector. Note that the exit
time is infinite in this option.
3
Lock Set. To use this method you must install a lock switch with the
contacts connected to the ET terminals of a keypad. This facility is
available on keypad software version 1.4.2 onwards.
Note: 1. The lockswitch contacts must be closed circuit with the lock
unlocked.
2. Do not connect more than one lockswitch (or any other device) to the
keypad ET terminals.
To set the system the user first enters their access code at a keypad.
The control unit starts the exit tone. Note that the exit time is infinite in
this option. The user then closes the final exit zone and turns the key
in the lock switch to “locked”. The system sets seven seconds after
the lock switch contacts open (detector settling time), and changes the
final exit zone to a Normal Alarm zone.
To unset the system the user turns the lock switch to “unlocked”
(closing the lock switch contacts). The keypads start a continuous
tone. When the user opens the final exit zone the control unit starts
Page 34
496929
4. Programming
the entry timer. The user completes entry by unsetting the system in
the normal way.
Note: If an intruder opens the final exit door without first unlocking the
lockswitch then the control unit immediately starts an alarm.
If you select Timed (options 0), Terminate (option 1), or Final Door (option 2)
exit modes the system allows a seven second settling time after pressing an
exit terminate button or closing a final door.
40: System Auto Re-Arm
This Command lets you program the number of times that the system will rearm when the bell delay expires. The system re-arms all closed zones. Select
option 0 to make the system never re-arm (the system will go into alarm once
only). Select options 1 to 4 to make the system re-arm once, twice, three
times or always.
Use this Command in conjunction with Command 35 - First Circuit Response.
If the system has rearmed, then when a user enters the system through the
entry route the control unit will give an audible internal alarm in place of the
normal entry tone.
41: Bell Delay
When the system is set and (for example) an intruder violates a zone, then
the system waits for the programmed Bell Delay before operating the external
sounder. The system then operates the external sounder for the programmed
Bell Duration. See “Programming Commands” for the Command options.
42: Bell Duration
This Command lets you set the length of time the system will operate the
external sounder during an alarm. See “Programming Commands” for the
Command options.
43: Level A Entry Time
This Command lets you set the Entry Time for Full Set. See “Programming
Commands” for the Command options. The time starts when a user opens
any Final Exit zone.
44: Level A Exit Time
This Command lets you set the Exit Time for Full Set. See “Programming
Commands” for the Command options.
45: Entry/Exit Tone Volume
Use this Command to set the volume of entry/exit tones from the internal
sounder. If you select option 0 then the internal sounder gives no entry/exit
tones. If you select option 1 then the internal sounder gives quiet entry/exit
496929
Page 35
4. Programming
tones, while option 9 gives the loudest entry/exit tones. The internal sounder
demonstrates the volume of the tone when you enter the digit.
46: Tamper Alarm Annunciation
Use this Command to chose which sounders the control unit will activate for a
tamper alarm while the system is unset.
Option
0
Selects internal sounders only.
1
Selects keypad sounders only.
2
Selects internal sounders and keypad sounders.
50: CSID Code
To allow the customer to use the ‘Remote Reset’ facility, you must program
the control unit as ‘Engineer Reset’ (Command 33 option 1) and then install a
four digit Central Station Identification (CSID) code.
First make contact with the ARC and obtain the CSID code. Then ensure that
the system is in programming mode. Next, key in:
50 Y nnnn Y
Where nnnn is the "CSID Code".
The control unit now contains the same CSID code as the ARC. After an
alarm the control unit can generate a ‘Reset Code’ which will be recognised
by the ARC 7300 Remote Reset decode programmer.
After an alarm the user keys in their access code to silence the alarm, but
cannot reset the system. The system generates a four digit code number and
displays it on the keypad. The user calls the ARC and tells them the number
shown on the keypad display. The ARC verifies the user's identity, then enters
the code number into a special programmer. The programmer generates an
‘Anti Code’, which the ARC gives back to the user. The user then enters the
‘Anti Code’ at the keypad to reset the system.
Note: To delete a CSID code key in “0000” over the existing code.
51: Setting Time and Date
The system has an internal clock/calendar which it uses to date stamp the log
print-out. To set the system’s clock/calendar to the correct time and date:
1. Enter programming mode (if you are not already there).
2. Key in 51Y at the keypad.
The display shows the current date, for example:
3.
D11 M09 Y01
Key in two digits for the day number and press Y. Use a leading zero for
the first nine days of the month.
Page 36
496929
4. Programming
4.
5.
Key in the two digits for the month number and press Y . Use a leading
zero for January to September.
Key in the two digits of the year and press Y.
The display shows the current time, for example:
6.
7.
H09 M15
Key in two digits for the hours of the day and press Y. Use the 24-hour
clock.
Key in two digits for the minutes and press Y.
The keypad sounder gives a double “bleep” and the display shows
“Installer Mode”. The system sets its internal clock/calendar to the time
you have given it.
52: Omit Tamper Allowed
This Command ensures that the control unit omits the tamper contacts as well
as the alarm contacts when a user omits a zone.
Note: You must give the zone the omit attribute to allow the user to omit a
zone.
Option
0
The control unit omits alarm contacts only
1
The control unit omits both alarm and tamper contacts when the user
omits a zone.
53: Abort Reset
Option
0
Ensures that reset after abort is the same as system reset (see
Command 33).
1
Enables customer reset after an abort.
60: Level B Final Exit Operation
Command 60 controls how the system will treat Final Exit zones in part set
Level B. When the Command option is set to 0 any Final Exit zones included
in part set B will continue to act as Final Exit zones during part set B. When
the option is set to 1 any Final Exit zones included in part set B will act as
Normal Alarm zones during part set B.
61: Level B Entry Route Response
Command 61 controls how the system treats Entry Route zones during part
set B. When the option is set to 0 all Entry Route zones included in part set B
will continue to act as Entry Routes during part set B. When the option is set
496929
Page 37
4. Programming
to 1 any Entry Route zones included in part set B will act as Final Exit zones
during part set B.
62: Level B Exit Mode
Command 62 specifies the exit mode for Level B.
Option
0
Low Tone. Timed set with the exit tone fixed at half volume.Use
Command 65 to select the exit time.
1
Instant Set (no exit tone)
2
Silent Set. (Timed Set with no exit tone) .Use Command 65 to
program the Exit time.
3
As A. The exit mode chosen for Level A (whole system) is also
applied to this level.
Note: The keypads give a double beep confirmation tone at the end of all
setting modes.
63: Level B Alarm Response
Command 63 specifies the alarm response for Level B.
Option
0
Keypad sounders.
1
Internal sounders and keypad sounders
2
Local alarm (internal and external sounder only).
3
Full alarm (communication outputs and internal/external sounders).
64: Level B Entry Time
This Command sets the entry time for Level B. See “Programming
Commands” for options.
65: Level B Exit Time
This Command sets the exit time for Level B. See “Programming Commands”
for options.
70: Level C Final Exit Operation
Command 70 controls how the system will treat Final Exit zones in part set
Level C. When the Command option is set to 0 any Final Exit zones included
in part set Level C will continue to act as Final Exit zones during part set Level
C. When the option is set to 1 any Final Exit zones included in part set Level
C will act as Normal Alarm zones during part set C.
Page 38
496929
4. Programming
71: Level C Entry Route Operation
Command 71 controls how the system treats Entry Route zones during part
set Level C. When the option is set to 0 all Entry Route zones included in part
set Level C will continue to act as Entry Routes during part set Level C. When
the option is set to 1 any Entry Route zones included in part set Level C will
act as Final Exit zones during part set C.
72: Level C Exit Mode
Command 72 specifies the exit mode for Level C.
Option
0
Low Tone. Timed set with the exit tone fixed at half volume. Use
Command 75 to select the exit time.
1
Instant Set (no exit tone)
2
Silent Set. (Timed Set with no exit tone) .Use Command 75 to
program the Exit time.
3
As A. The exit mode chosen for Level A (whole system) is also
applied to this level.
Note: The keypads give a double beep confirmation tone at the end of all
setting modes.
73: Level C Alarm Response
Command 73 specifies the alarm response for Level C.
Option
0
Keypad sounders only.
1
Internal sounders and keypad sounders.
2
Local alarm (internal and external sounder only).
3
Full alarm (communication outputs and internal/external sounders).
74: Level C Entry Time
This Command sets the entry time for Level C. See “Programming
Commands” for options.
75: Level C Exit Time
This Command sets the exit time for Level C. See “Programming Commands”
for options.
76: Level D Exit Mode
Command 76 specifies the exit mode for Level D.
Option
496929
Page 39
4. Programming
0
Low Tone. Timed set with the exit tone fixed at half volume. Use
Command 79 to select the exit time.
1
Instant Set (no exit tone)
2
Silent Set. (Timed Set with no exit tone ).Use Command 79 to
program the Exit time.
3
As A. The exit mode chosen for Level A (whole system) is also
applied to this level.
Note: That the keypads give a double beep confirmation tone at the end of all
setting modes.
77: Level D Alarm Response
Command 77 specifies the alarm response for Level D.
Option
0
Keypad sounders only.
1
Internal sounders and keypad sounders.
2
Local alarm (internal and external sounder only).
3
Full alarm (communication outputs and internal/external sounders).
78: Level D Entry Time
This Command sets the entry time for Level D. See “Programming
Commands” for options.
79: Level D Exit Time
This Command sets the exit time for Level D. See “Programming Commands”
for options.
81, 82, 83, : Output Programming
The system has three transistorised, high current, programmable outputs.
Command 81 programs output 1, Command 82 programs output 2 and,
Command 83 programs output 3. All three Commands take a single following
digit that selects the function.
Note: The outputs are a "pull down” type that provide negative applied control
signals. The outputs float(neither + or -) when inactive, and 0V when
active.
Page 40
496929
4. Programming
Output Type
Option
00
Bell. - The control unit operates this output during an alarm. Use
Command 41 to control bell delay and 42 to control bell duration.
01
EE Follow. - This output is active when the entry or exit time starts
and deactivates at the end of the entry/exit time, or if the entry/exit
time is terminated. The output can be used for a separate entry/exit
buzzer. Note that the output does not give a tone during part set if the
exit mode is silent set or instant set.
02
Armed lamp. - The output is active continuously while the system is
full or part set.
03
PIR Set Latch. - This output is active when the system is set and
deactivates when the system is unset or an alarm condition occurs.
The output will also activate for one second when a reset is performed
or the control unit leaves programming mode. In addition, the output is
active during a walk test.
04
Shock Reset. - This output is used to reset shock sensors, (for
example the ‘Viper or Trapper’). The control unit triggers the output at
the start of the exit period. The output remains active for a fixed time
of five seconds.
05
Walk Test. - This output is active during both engineer and user walk
test and in the period between silencing the system and resetting the
system. This output type is used on movement detectors which have
the facility to switch off the walk test LED in any state other than a
walk test.
06
Ready Lamp. - (System is Clear to Set) This output is active when the
system is unset, and if there are no faults. The output is inactive when
the system is full or part set, during any alarm, or if a circuit fault
prevents setting (Final Door and Entry Route zone types are ignored).
Note: The output will also be active when the control unit is in programming
mode.
07
24 Hour alarm. - This output will become active if a zone designated
as ’24 Hours’ is violated. The output deactivates when the system is
disarmed.
08
Strobe. - In an alarm the system operates the output. The output
remains active until the user disarms the system.
09
Smoke Reset. - This output is designed to be connected to low
voltage smoke detector reset terminals. The control unit operates the
496929
Page 41
4. Programming
output for 3 seconds when the system is reset after any alarm has
occurred.
10
Siren Test. - This output becomes active when the Installer performs a
sounder test using Command 91.
11
Strobe Set. - This output is active for 10 seconds after the system has
set. The output can be used to operate the strobe to give a visual
indication that the system has completed setting.
12
Pulse Set o/p 1. - This output becomes active for a programmable
time period between 1 – 12 seconds (in command 170) & when the
assigned level(s) (ABCD) (in command 171) is set.
13
Pulse Unset o/p 1. - This output becomes active for a programmable
time period between 1 – 12 seconds (in command 172) & when the
assigned level (ABCD) (in command 173) is set.
26
Pulse Set o/p 1. - This output becomes active for a programmable
time period between 1 – 12 seconds (in command 170) & when the
assigned level (ABCD) (in command 171) is set.
27
Pulse Set o/p 2. - This output becomes active for a programmable
time period between 1 – 12 seconds (in command 170) & when the
assigned level (ABCD) (in command 171) is set.
28
Pulse Set o/p 3. - This output becomes active for a programmable
time period between 1 – 12 seconds (in command 170) & when the
assigned level (ABCD) (in command 171) is set.
29
Pulse Set o/p 4. - This output becomes active for a programmable
time period between 1 – 12 seconds (in command 172) when
someone unsets the A or B or C or D levels (in command 171), or
during a fire or PA alarm (if the function is selected in commands 174
or 175).
30
Pulse Unset o/p 1. - This output becomes active for a programmable
time period between 1 – 12 seconds (command 172) when someone
unsets the A or B or C or D levels, or during a fire or PA alarm (if the
function is selected in commands 174 or 175).
31
Pulse Unset o/p 2. - This output becomes active for a programmable
time period between 1 – 12 seconds (command 172) when someone
unsets the A or B or C or D levels, or during a fire or PA alarm (if the
function is selected in commands 174 or 175).
32
Pulse Unset o/p 3. - This output becomes active for a programmable
time period between 1 – 12 seconds (command 172) when someone
unsets the A or B or C or D levels, or during a fire or PA alarm (if the
function is selected in commands 174 or 175).
Page 42
496929
4. Programming
33
Pulse Unset o/p 4. - This output becomes active for a programmable
time period between 1 – 12 seconds (command 172) when someone
unsets the A or B or C or D levels, or during a fire or PA alarm (if the
function is selected in commands 174 or 175).
85: Burglar Communications Re-arm
This Command determines what happens to the “Burg” communications
output at the end of the bell run time.
Option
0
Latched. The output stays active until an engineer or user resets the
system.
1
Rearm. The system rearms Channel 3 once the bell timer has expired.
Once the Channel is rearmed, the system is ready to report any new
alarm. The system bypasses any detectors that are still violated.
Note: 1. If a Final Exit Zone is triggered, Channel 3 becomes active at the end
of the Programmed Entry time, or,
2. If Dual Ply Entry is enabled (Command 86 1) and the Final Exit zone is
triggered then Channel 3 becomes active at the end of the 30 second
Dual ply grace period, or,
3. If Alarm Abort is enabled (Command 36 1) Channel 3 restores if the
user unsets the system.
86: Dual Ply Entry Warning
If users habitually exceed the entry time use option 1 to add a 30 second
extension during which the internal sounders give a warning tone. The
extension applies to both Full and Part setting.
If users exceed the dual ply entry warning during full set then the system
gives a full alarm. If users exceed the dual ply entry warning during part set
then the system gives an alarm that is determined by Commands 63 for part
set B, 73 for part set C, or 77 for part set D.
Use Option 0 (default) to disable Dual Ply Entry.
87: Keypad Dual Key Alarms
This Command allows users to raise a alarms by pressing two keys on the
keypad at the same time. When this facility is enabled (option 1) the alarms
available are:
PA alarm
keys 1 and 3
Medical alarm
keys 4 and 6
Fire alarm
keys 7 and 9
Use option 0 to disable this Command.
496929
Page 43
4. Programming
90 - 97: See “5.Testing”
98: Load Full Defaults
Use this Command to load default values for all Commands.
1. Enter programming mode (if you are not already there).
2. Key in 98 Y at the keypad.
The display shows:
3.
4.
Load default
Press 1. (You can press X to stop the procedure if you change your mind
at this stage.)
Press Y.
The keypad gives a double confirmation tone and the system loads the
factory default Command values, erasing all previously programmed
values.
Note: The log is protected and cannot be erased by the Installer.
99: Leave Programming Mode
To leave programming mode:
1. Key in 99 Y at the keypad.
The display shows:
2.
Exit Eng?
Press Y.
The display shows:
and after a few seconds the control unit
resets itself and returns to user mode.
Checking System
If any 24 hour, Fire, PA or Technical zones or any tamper switches are active
when you try to leave
programming mode then the keypad gives an error tone and displays all the
faults.
Clear the faults shown on the display and press Y. Repeat steps 1 and 2 and
the control unit should leave programming mode.
Page 44
496929
4. Programming
126: Select Language
The control unit can display messages on the keypads in one of several
different languages. Use Command 126 to select the language you wish to
use. The options available are:
0: English (default)
5: Francai (French)
1: Italian
6: Deutsch (German)
2: Espanol (Spanish)
7: Norsk (Norwegian)
3: Portugu (Portuguese) 8: Svenska (Swedish)
4: Nederl (Dutch)
9: Dansk (Danish)
151 - 158: Plug by Communicator Outputs
The main circuit board of the control unit provides eight programmable
outputs that can be used to control a plug-by communicator. The outputs can
be connected to the communicator by an twelve-way wiring harness provided
with the control unit. See “3. Installation - Fitting a Plug-by Communicator” for
details of the wiring harness.
Commands 151 to 158 allow you to assign one of several options to each
output. Command 151 controls output 1, 152 output 2, and so on up to
Command 158 which controls output 8. Each Command has the same
options, as follows:
00 Not used
16 Medical Assistance
01 Fire
17 Key Box
02 PA
18 Anti Mask
03 Burglar
19 Smoke Detector
04 Open/Close
30 Set o/p 1
05 Alarm Abort
31 Set o/p 2
06 Technical Alarm
32 Set o/p 3
11 AC Fail
33 Set o/p 4
12 Tamper Alarm (Day tamper)
34 Unset o/p 1
13 Open
35 Unset o/p 2
14 Close
36 Unset o/p 3
15 Zone Omitted
37 Unset o/p 4
159: Invert Plug by Outputs
This option allows the plug by outputs to operate as +ve applied. (By default
the outputs operate as +ve removed.)
Option
0 +ve Removed to trigger. The inactive output is +ve. When active the
output goes to 0V.
496929
Page 45
4. Programming
1 +ve Applied to trigger. The inactive output floats. When active the output
goes +ve.
170 - 175: Pulsed Set & Unset Output Options
Use commands 170 to 175 to apply additional options to the output types
pulsed set o/p 1-4 and pulsed unset o/p 1-4.
Example 1: Panel output 3 is programmed with the output type 12 (Pulsed set
o/p 1). This is required to operate a locking mechanism when the system is
set. The locking system requires a pulsed trigger time of 6 seconds
(command 170 - Set o/p 1 is programmed as 06 seconds). This is only to be
applied when the whole system is set. Select level A in command 171 Set
O/p 1).
The programming sequence for the physical panel output no. 3 is:
Command 83 = 12 (Output type - Pulsed Set o/p 1)
Command 170 = (set 1 = 06) seconds
Command 171 = (set 1 = a) level
Example 2: Panel output 3 is programmed with the output type 13 (Pulsed
Unset o/p 1). This is required to operate an unlocking mechanism when the
system is set. The unlocking system requires a pulsed trigger time of 8
seconds (command 172 - Set o/p 1 is programmed as 08 seconds). This is
only to be applied when the whole system is Unset. Select level A in
command 173 Set O/p 1). In addition if a Fire or PA alarm occurs then the
output will be active for the programmed time.
The programming sequence for the physical panel output 3 is: Command 83 = 13 (Output type - Pulsed Unset o/p 1)
Command 172 = (set 1 = 08) seconds
Command 173 = (set 1 = a) level
Command 174 = (Fire o/p 1) active if Fire alarm
Command 175 = (PA o/p 1) active if PA alarm
The Pulsed set o/p commands are:
(use tick key to scroll round o/p 1-4)
170 Set o/p 1 Time, select a time in the range 01-12 seconds
Set o/p 2 Time, select a time in the range 01-12 seconds
Set o/p 3 Time, select a time in the range 01-12 seconds
Set o/p 4 Time, select a time in the range 01-12 seconds
171 Set o/p 1 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Set o/p 2 ABCD, select the level(s) in which the output will be active
toggle abcd keys to select level on /off.
Page 46
496929
4. Programming
172
173
174
175
Set o/p 3 ABCD, select the level(s) in which the output will be active
toggle abcd keys to select level on /off.
Set o/p 4 ABCD, select the level(s) in which the output will be active
toggle abcd keys to select level on /off.
Unset o/p 1 Time, select a time in the range 01-12 seconds
Unset o/p 2 Time, select a time in the range 01-12 seconds
Unset o/p 3 Time, select a time in the range 01-12 seconds
Unset o/p 4 Time, select a time in the range 01-12 seconds
Unset o/p 1 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Unset o/p 2 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Unset o/p 3 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Unset o/p 4 ABCD, select the level(s) in which the output will be active,
toggle abcd keys to select level on /off.
Fire o/p 1, Select as on if O/P 1 is to respond if a Fire alarm occurs
Fire o/p 2, Select as on if O/P 2 is to respond if a Fire alarm occurs
Fire o/p 3, Select as on if O/P 3 is to respond if a Fire alarm occurs
Fire o/p 4, Select as on if O/P 4 is to respond if a Fire alarm occurs
PA o/p 1, Select as on If O/P 1 is to respond if a PA alarm occurs
PA o/p 2, Select as on If O/P 2 is to respond if a PA alarm occurs
PA o/p 3, Select as on If O/P 3 is to respond if a PA alarm occurs
PA o/p 4, Select as on If O/P 4 is to respond if a PA alarm occurs
Note: For options 174 to 175 use 1 for ON and 0 for OFF.
496929
Page 47
5. Testing
Reading the Log (Command 90)
The control unit keeps a log of recent events The log can contain up to 250
events. Each event is represented by a short text message, shown below and
on the next page. To review the event log, make sure the system is in
programming mode, then:
1. Key in 90Y.
The display shows the most recent event in the log. For a list of the log
messages see below.
2. Key in 1 to show earlier events or 3 to see more recent events.
3. Press Y to toggle between the event message and the event time.
4. Press X to leave the log.
The table below and on the next page shows all the messages that can
appear in the event log. The left hand column shows the messages that
appear on a keypad display.
Note: Each event in the log is accompanied by the date and time in numerical
format.
Neither the Installer nor the user can erase the log.
In the log user codes are represented by numbers as follows:
U00
Installer
U19
Idle
U01
User code 1
...
...
U21
Keyswitch
U16
User code 16
U22
Remote Reset
U17
Duress code
U18
Control Unit
Keypad and Event Log Displays
Keypad
AC Fail
AC Restore
Alarm Abort
Aux DC Fail
Aux DC Fail Rstr
Bad Checksum
Batt Missing
Batt Missing Rstr
Burg Znn Alarm
Burg Znn Rstr
Codes Defaulted
Defaults Loaded
Page 48
Meaning
Mains supply failed
Mains supply restored
User aborted alarm
Aux power failed
Aux power restored
The control unit has detected data corruption in its memory
Battery disconnected
Battery re-connected
Intruder alarm on zone nn
Instruder alarm on zone nn restored
User access codes and installer code returned to default values
All programming defaults loaded
496929
5. Testing
Keypad
EEProm Fail
Fire Znn Alarm
Fire Znn Reset
Fire Znn Rstr
Knn Excess Keys
Knn Missing
Knn Restore
Knn Tamper
Tamper Knn Restr
Fr Knn Alarm
Md Knn Alarm
Key Sw Set Znn
Key Sw UnsetZnn
Key Box Cls Znn
Key Box Opn Znn
Lid Tamp Rst
Lid Tamper
Low Batt Rstr
Low Battery
PA Knn Alarm
PA Znn Alarm
PA Znn Rstr
Set Fail Znn
Smk Det Alm Znn
Smk Det Res Znn
Soak Fail Znn
Sounder Tamp Rst
Sounder Tamper
System Rearmed
System Startup
Tamper Znn
Tamper Znn Rstr
Tech Znn Alarm
Tech Znn Rstr
Tel Line Fault
Tel Line Rstr
Unn Change Unn
Unn Delete Unn
Unn Off-Site
Unn On-Site
Unn System Reset
Unn System Set
Unn System UnSet
Unn Time/Date
Unn Znn Omit
Unn Znn Unomit
Meaning
Control unit memory damaged
Fire alarm on zone nn
Fire alarm on zone nn reset
Fire alarm on zone nn restored
User has tried to enter access code too many times on keypad nn
Keypad nn disconnected
Keypad nn re-connected
Tamper alarm on keypad nn
Tamper alarm on keypad nn
Fire alarm started at keypad nn
Medical alarm started at keypad nn
System set by keyswitch on zone nn
System unset by keyswitch on zone nn
Keybox on zone nn closed
Keybox on zone nn opened
Control unit lid tamper alarm restored
Control unit lid tamper alarm
Control unit low battery restored
Low battery on control unit
Panic alarm raised from keypad nn
Panic alarm raised from zone nn
Panic alarm on zone nn restored
System setting failed because of fault on zone nn
Smoke detector alarm on zone nn
Smoke detector on zone nn restored
Soak fail test on zone nn caused alarm
Tamper on sounder restored
Sounder tamper
System rearmed
Power applied to system
Zone nn tamper alarm
Tamper alarm on zone nn restored
Technical alarm on zone nn
Technical alarm restored on zone nn
Telephone line fault detected
Telephone line restored
User nn changed access code for user nn
User nn deleted access code for user nn
Engineer exited programming mode
Engineer entered programming mode
User nn reset system
User nn set system
User nn unset system
User nn changed the time and date
User nn omitted zone nn
User nn un-omitted zone nn
496929
Page 49
5. Testing
Testing Outputs (Commands 91-96)
You may test parts of the system by entering commands at the keypad. To
carry out a test make sure the system is in programming mode and then key
in one of the following commands. Press Y to end each test:
91Y To test output 1 (usually the external sounder/bell).
92Y To test output 2 (usually the strobe output).
93Y To test output 3.
95Y To test the keypad sounder.
Engineer Walk Test (Command 97)
Allows the engineer to test all devices on the system.
1. Enter programming mode.
2. Key in 97 Y
The display shows:
3.
97: Walk Test
Open and close each alarm and tamper contact in turn.
The system gives a chime tone each time you open and close a detector
contact. The displays shows: "A:Zone:" and the zone number of every
detector you have tested (note that the display shows each zone number
for one second, in sequence). If you also test the tampers on each zone
the display shows the letter "T" against each zone number.
4. Press X to stop the walk test.
Note that the Engineer's walk test allows you to test all zones including PA
zones, zone tampers, and control unit and bell tampers. The user's walk test
does not allow you to test PA, Fire, 24Hr, Technical zones, or tampers.
Page 50
496929
Index
24 hour alarm............................................................. 41
24 hour zones ............................................................ 27
Access codes ............................................................... 5
restoring ................................................................ 25
Alarm Abort
description ............................................................. 33
Alarm response
Level B .................................................................. 38
Level C .................................................................. 39
Level D .................................................................. 40
Anti code .................................................................... 36
Anti mask ................................................................... 29
Armed lamp................................................................ 41
Auto re-arm ................................................................ 35
Auxilliary
output ...................................................................... 6
Battery.......................................................................... 6
fitting...................................................................... 18
Bell ............................................................................. 41
current ..................................................................... 6
delay...................................................................... 35
duration ................................................................. 35
Bell tamper................................................................... 6
Bell test ...................................................................... 50
Burg comms rearm..................................................... 43
Cable entries.............................................................. 11
CC wiring ................................................................... 13
Chime......................................................................... 29
Communicator............................................................ 16
cabling ................................................................... 17
connection ............................................................. 17
fitting...................................................................... 16
output ...................................................................... 6
Plug on .................................................................... 3
Continuous sounder ................................................... 31
Control Unit
diagram ................................................................... 3
fitting case ............................................................... 9
CSID .......................................................................... 36
CSID code.................................................................. 36
Defaults
Country.................................................................. 26
Load full................................................................. 44
restoring ................................................................ 25
Dimensions .................................................................. 6
Double Knock............................................................. 30
Dual ply entry ............................................................. 43
Duress code............................................................... 20
Engineer code............................................................ 20
changing................................................................ 30
Entry alarm delay time ............................................... 32
Entry route ................................................................. 28
Entry route response
Level B .................................................................. 37
Level C .................................................................. 39
Entry time................................................................... 40
Level A .................................................................. 35
Level B .................................................................. 38
Level C .................................................................. 39
Entry/Exit
Scandinavian ......................................................... 29
Entry/exit follow.......................................................... 41
Entry/Exit tone............................................................ 35
Exit fault external sounders ....................................... 31
Exit mode
Level A .................................................................. 34
Level B .................................................................. 38
Level C .................................................................. 39
Level D .................................................................. 39
Exit terminate button.................................................. 12
Exit time ..................................................................... 40
Level A .................................................................. 35
Level B .................................................................. 38
Level C .................................................................. 39
Final door set ............................................................. 34
Final exit .................................................................... 27
Final Exit Response
Level B .................................................................. 37
Level C .................................................................. 38
Fire ............................................................................ 27
First circuit response.................................................. 33
Forbikobler................................................................. 29
Four wire CC.............................................................. 13
FSL ............................................................................ 14
resistor colour code ............................................... 14
Fuse........................................................................... 11
Fuses........................................................................... 6
Inputs........................................................................... 6
Instant Set ................................................................. 34
Key box...................................................................... 28
Key switch ................................................................. 28
Keypad ........................................................................ 3
addressing............................................................. 12
backlight ................................................................ 12
backplate............................................................... 10
current.................................................................... 6
displays ................................................................. 32
dual key alarm....................................................... 43
fitting ....................................................................... 9
sounder test .......................................................... 50
tamper ............................................................... 9, 10
Keyswitch
Wiring .................................................................... 15
Kick start pins ............................................................ 18
Language selection.................................................... 45
Level D
alarm response ..................................................... 40
entry time .............................................................. 40
exit time................................................................. 40
Line fault input ............................................................. 6
Load full defaults........................................................ 44
Log............................................................................. 48
viewing .................................................................. 48
Loudspeaker ................................................................ 6
Loudspeaker chime ................................................... 31
Mains connection....................................................... 11
Normal alarm ............................................................. 27
Not used .................................................................... 27
Omit allow............................................................ 27, 30
Omit tamper ............................................................... 37
Output
communicator.......................................................... 6
plug by communictor ............................................. 45
programming ......................................................... 40
testing.................................................................... 50
type ................................................................. 40, 41
496929
Page 51
using ......................................................................14
PA reset......................................................................33
Panic Alarm ................................................................27
PCB ..............................................................................7
Plug by communicator outputs ...................................45
Power
Control unit current ..................................................6
Programming commands ...........................................20
Programming mode ....................................................20
leaving .............................................................24, 44
re-entering .............................................................25
Pulse Set ....................................................................42
Pulse Unset ................................................................42
Ready lamp ................................................................41
Reset
after abort ..............................................................37
engineer.................................................................24
RedCare ..................................................................6
remote....................................................................36
shock .....................................................................41
tellback...................................................................31
Sensitivity ...................................................................30
Set latch .....................................................................41
Shock analyser...........................................................28
Shock reset ................................................................41
Silent or audible PA ....................................................32
Siren test ....................................................................42
Smoke detector ..........................................................28
Smoke reset ...............................................................41
Soak Test ...................................................................29
Sounders ....................................................................12
Specification .................................................................6
Page 52
Start up ......................................................................18
Status display............................................................. 32
Strobe ........................................................................ 41
testing .................................................................... 50
Strobe set................................................................... 42
Strobe while setting.................................................... 42
System tamper reset .................................................. 34
Tamper alarm annunciation ....................................... 36
Tamper communication.............................................. 33
Tamper return .............................................................. 6
Technical.................................................................... 28
Tellback........................................................................ 6
Tellback reset............................................................. 31
Terminate................................................................... 34
Testing ....................................................................... 48
Time and date ............................................................ 36
Timed ......................................................................... 34
User codes ................................................................. 20
Walk test .............................................................. 41, 50
Weight.......................................................................... 6
Zone
attributes................................................................ 29
description ............................................................... 5
names.................................................................... 26
programming ......................................................... 26
types ...................................................................... 27
wiring ..................................................................... 13
Zone configuration ..................................................... 31
Zone Name ................................................................ 30
deleting .................................................................. 26
Zone tamper reset...................................................... 32
496929
Notes
496929
Page 53
Declaration of Conformance
Cooper Security Ltd issues this certificate to
certify that the equipment known as:
9651
Complies with the following directive:
1995/5/EC R&TTE Directive
Signed
Stewart Taylor, Technical Director
Date: 6/2/2004
Cooper Security Ltd.
Security House
Vantage Point Business Village
Mitcheldean
Gloucestershire
GL17 0SZ
www.scantronic.co.uk
Product Support (UK) Tel: +44 (0) 870 757 5400.
Available between:
08:15 and 17:00 Monday to Thursday,
08:15 and 12:45 Friday.
Emergency service only between 12:45 and 17:00 Friday.
Product Support Fax: (01594) 545471
Part Number 496929 Issue 2