Sharp Notevision XR-1X Specifications

Introduction
MODEL
XR-1X
XR-1S
Setup
OPERATION MANUAL
Quick Start
MULTIMEDIA PROJECTOR
Connections
Basic
Operation
Useful
Features
(The picture shown above is of the XR-1S.)
Appendix
IMPORTANT
For your assistance in reporting the loss or
theft of your Projector, please record the
Model and Serial Number located on the
bottom of the projector and retain this
information. Before recycling the packaging, please be sure that you have checked
the contents of the carton thoroughly
against the list of “Supplied accessories”
on page 11.
Model No.:
Serial No.:
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 5A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362
and of the same rating as above, which is also indicated on the pin
fuse marked or
face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 5A socket
outlet, as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol or coloured green or
green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.
• The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
The supplied CD-ROM contains operation instructions in English, German, French,
Swedish, Spanish, Italian, Dutch, Portuguese, Chinese (Traditional Chinese and Simplified Chinese) and Korean. Carefully read through the operation instructions before
operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,
Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinesisch (Traditionelles
Chinesisch und einfaches Chinesisch) und Koreanisch. Bitte lesen Sie die
Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand,
français, suédois, espagnol, italien, néerlandais, portugais, chinois (chinois traditionnel et
chinois simplifié) et coréen. Veuillez lire attentivement ces instructions avant de faire
fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska,
franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska (traditionell
kinesiska och förenklad kinesiska) och koreanska. Läs noga igenom bruksanvisningen
innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán,
francés, sueco, español, italiano, holandés, portugués, chino (chino tradicional y chino
simplificado) y coreano. Lea cuidadosamente las instrucciones de operación antes de
utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese,
svedese, spagnolo, italiano, olandese, portoghese, cinese (cinese tradizionale e cinese
semplificato) e coreano. Leggere attentamente le istruzioni per l’uso prima di usare il
proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds,
Spaans, Italiaans, Nederlands, Portugees, Chinees (Traditioneel Chinees en
Vereenvoudigd Chinees) en Koreaans. Lees de handleiding zorgvuldig door voor u de
projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,
Sueco, Espanhol, Italiano, Holandês, Português, Chinês, (Chinês Tradicional e Chinês
Simplificado) e Coreano. Leia cuidadosamente todas as instruções de operação antes
de operar o projetor.
Introduction
Introduction
Before using the projector, please read this operation manual carefully.
ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP
Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service
and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING:
High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the operation manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
U.S.A. ONLY
1
The enclosed computer cable must be used with the device. The cable is provided to
ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters
standby mode. During normal operation, when putting the projector into standby mode always
use the ON/STANDBY button on the projector or on the remote control. Ensure the cooling fan has
stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING
THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or, if you are
located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
CAUTION ON LITHIUM BATTERY (for Remote Control unit)
If a battery is reversed (positive end where the negative end belongs and vice versa), it can
overheat and rupture. This has happened when young children install batteries backwards.
Warn children not to take out batteries or install them. Parents should install the lithium
battery in the remote control.
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 55.
LAMP REPLACEMENT WARNING
BEFORE REMOVING THE SCREW, DISCONNECT POWER
CORD. HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL
BEFORE REPLACING THE LAMP. REPLACE WITH SAME
SHARP LAMP UNIT MODEL AN-XR1LP ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF
LAMP BEFORE SERVICING.
HIGH PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL
HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED.
HANDLE WITH CARE. SEE OPERATION MANUAL.
AVERTISSEMENT A OBSERVER LORS
DU REMPLACEMENT DE LA LAMPE.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE
RETIRER LES VIS. L’INTERIEUR DU BOITIER ETANT
EXTREMEMENT CHAUD, ATTENDRE 1 HEURE AVANT DE
PROCEDER AU REMPLACEMENT DE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE MODÈLE
AN-XR1LP.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES
YEUX. ETEINDRE LA LAMPE AVANT DE PROCEDER
A L’ENTRETIEN.
LAMPE A HAUTE PRESSION : RISQUE D’EXPLOSION.
DANGER POTENTIEL DE PARTICULES DE VERRE EN CAS
D’ECLATEMENT DE LA LAMPE. A MANIPULER AVEC
PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
This SHARP projector uses a DMD panel. This very sophisticated panel contains 786,432 (XR1X) / 480,000 (XR-1S) pixels micromirrors. As with any high technology electronic equipment
such as large screen TVs, video systems and video cameras, there are certain acceptable
tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
2
Introduction
How to Read this Operation Manual
■ The specifications of the XR-1X are slightly different from those of the XR-1S, however, you can
connect and operate both models in the same manner. This operation manual uses the XR-1S
for the purpose of explanation.
• In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from actual display.
Using the Menu Screen
The menu can be operated to achieve two functions, adjustment and setting. (For setting the menu
items, see pages 38 and 39.)
Operating with the projector
When “PRJ - ADJ” - “Guide LEDs” is set to “On”, the buttons used for menu adjustment on the
projector light up.
Example: When W, Y and the MENU/HELP button light up on the projector, you can use those
buttons for operation.
Adjustment buttons (W/Y/V/X)
MENU/HELP button
ENTER button
MENU/HELP
button
MOUSE Adjustment
button (P/R/O/Q)
ENTER button
RETURN button
Buttons used in
this operation
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
1
Press BMENU.
2
Press Q or O to display the other
menu screen.
• The “Picture” menu screen for the selected input mode is displayed.
• The selected menu item is highlighted.
Example: “Picture” screen menu for INPUT 1
(RGB) mode
Menu item
Picture
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
SEL./ADJ.
SCR - ADJ
PRJ - ADJ
Button used in
this step
Help
Standard
0
0
0
0
7500K
On-screen
display
Off
Off
ENTER
END
36
Info
........Indicates safeguards for using the projector.
Note .........Indicates additional information for setting up and operating the
projector.
For Future Reference
Maintenance
P. 52
Troubleshooting
PP. 60 and 61
Index
P. 65
3
Contents
Preparing
Introduction
Setup
How to Read this Operation Manual .... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
How to Access the PDF Operation
Manuals ............................................ 10
Accessories ........................................ 11
Part Names and Functions ................. 12
Setting up the Projector ...................... 18
Inserting the Lithium Battery ................ 14
Usable Range ...................................... 15
Quick Start
Quick Start .......................................... 16
Setting up the Projector ....................... 18
Standard Setup (Front Projection) ....... 18
Projecting a Reversed Image .............. 18
Screen Size and Projection Distance
(XR-1X) ............................................... 19
Screen Size and Projection Distance
(XR-1S) ............................................... 20
Connections
Connections ........................................ 21
Samples of Cables for Connection .... 22
Connecting to a Computer ................. 23
Connecting to Video Equipment ......... 24
Connecting the Power Cord ............... 25
Using
Basic Operation
Turning the Projector On/Off .............. 26
Turning the Projector on ....................... 26
Turning the Power off (Putting the
Projector into Standby Mode) ........... 26
Image Projection ................................. 27
About the Setup Guide ........................ 27
Adjusting the Projected Image ............ 27
Switching the Input Mode .................... 29
Adjusting the Volume ........................... 29
Displaying the Black Screen and Turning
off the Sound Temporarily ................. 29
Resize Mode ......................................... 30
Useful Features
Adjusting/Operating with the
Remote Control ................................ 32
Auto Sync (Auto Sync Adjustment) ..... 32
Freezing a Moving Image .................... 32
Selecting the Picture Mode .................. 32
Using Mouse Function ......................... 33
Menu Items ......................................... 34
Using the Menu Screen ...................... 36
Menu Selections (Adjustments) ........... 36
Menu Selections (Settings) .................. 38
Picture Adjustment (“Picture” menu) .. 40
Selecting the Picture mode .................. 40
Adjusting the Image ............................. 40
Adjusting the Color Temperature ......... 41
Emphasizing the Contrast .................... 41
Progressive ........................................... 42
sRGB Setting ........................................ 42
Adjusting the Projected Image
(“SCR - ADJ” menu) ......................... 43
Setting the Resize Mode ...................... 43
Adjusting the Image Position ............... 43
Keystone Correction ............................ 44
Setting On-screen Display ................... 44
Selecting the Background Image ........ 45
Setting the Setup Guide ....................... 45
Reversing/Inverting Projected
Images ............................................... 46
Selecting the On-screen Display
Language ........................................... 46
Setting the Projector Function
(“PRJ - ADJ” menu) .......................... 47
Eco/Quiet Mode ................................... 47
Auto Search Function ........................... 47
Auto Power Off Function ...................... 48
Setting the Guide LEDs ........................ 48
System Lock Function .......................... 49
Setting/Changing the keycode ............ 49
Setting the Confirmation Sound ........... 50
Checking the Lamp Life Status ........... 50
Troubleshooting with “Help” menu ..... 51
Displaying “Help” menu screen .......... 51
4
Introduction
Reference
Appendix
Maintenance ....................................... 52
Maintenance Indicators ...................... 53
Regarding the Lamp ........................... 55
Lamp ..................................................... 55
Caution Concerning the Lamp ............ 55
Replacing the Lamp ............................. 55
Removing and Installing
the Lamp Unit .................................... 56
Resetting the Lamp Timer .................... 57
Connecting Pin Assignments ............. 58
Computer Compatibility Chart ............ 59
Troubleshooting .................................. 60
For SHARP Assistance ....................... 62
Specifications ..................................... 63
Dimensions ......................................... 64
Index ................................................... 65
5
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its installation,
use and servicing.
1. Read Instructions
All the safety and operating instructions should
be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be
retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be
followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example,
near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a
swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
6
10. Ventilation
Slots and openings in the cabinet are provided
for ventilation to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
11. Power Sources
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your product dealer
or local power company. For products intended
to operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with
a grounding terminal.
This plug will only fit into a grounding type
power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
14. Lightning
For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system.
This will prevent damage to the product due to
lightning and power-line surges.
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can
result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
17. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the
operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the product
to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change
in performance, this indicates a need for
service.
Introduction
15. Overloading
19. Replacement Parts
When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
21. Heat
This product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
• DLP\ (Digital Light Processing) and DMD\ (Digital Micromirror Device) are trademarks
of Texas Instruments, Inc.
• Microsoft and Windows are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
• Adobe Reader is a trademark of Adobe Systems Incorporated.
• Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• All other company or product names are trademarks or registered trademarks of their
respective companies.
7
Be sure to read the following safeguards when setting
up your projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp ruptures. In case
of lamp rupture, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center for a replacement.
See “Replacing the Lamp” on
page 55.
■ When placing the projector in a high position,
be sure to secure it carefully to avoid personal injury caused by the projector falling
down.
Do not subject the projector to hard impact and/or vibration.
AN-XR1LP
Caution concerning the setup of the projector
■ Take care with the lens so as not to hit or
damage the surface of the lens.
Rest your eyes occasionally.
■ For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from
humidity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Projector Dealer or
Service Center.
■ Continuously watching the screen for long
hours will cause eye strain. Be sure to occasionally rest your eyes.
Do not set up the projector in places exposed to direct sunlight or bright light.
■ Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Be sure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat
damage. This does not indicate a malfunction. (See pages 53 and 54.) Remove the projector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
■ When turning off the projector, the cooling fan
runs to decrease the internal temperature for
a while. Unplug the power cord after the cooling fan stops. The period the cooling fan runs
will vary, depending on the circumstances and
the internal temperature.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Caution regarding placing of the projector.
■ Place the projector on a level site within the
adjustment range of the adjustment foot.
Do not turn the projector upside down
immediately after putting into standby
mode.
■ This may cause burns due to rise in temperature of the lamp unit cover.
8
Warning about placing the projector in
a high position
Avoid locations with extremes of temperature.
■ The operating temperature of the projector is
from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
■ When transporting the projector, be sure not
to subject it to hard impact and/or vibration,
as this can result in damage. Take extra care
with the lens. Before moving the projector,
be sure to unplug the power cord from the
wall outlet, and disconnect any other cables
connected to it.
■ Do not carry the projector by holding the lens.
■ When transporting the projector, be sure to
place the projector in the supplied soft case.
(See page 11.)
Info
Introduction
Caution regarding transportation of the
projector
• The cooling fan regulates the internal temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in
the fan speed. This does not indicate malfunction.
• Do not unplug the power cord during projection or cooling fan operation. This can cause
damage due to rise in internal temperature,
as the cooling fan also stops.
Other connected equipment
■ When connecting a computer or other audiovisual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the operation manuals of the projector and the equipment to be connected for
instructions on how to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, be sure
to use an appropriate power cord for the country you are in.
Temperature monitor function
■ If the projector starts to overheat due to setup
problems or blockage of the air vents, “
” and
“
” will illuminate in the lower left corner
of the picture. If the temperature continues to
rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the projector
will enter standby mode. Refer to “Maintenance
Indicators” on page 53 for details.
9
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM,
so that you can work with the projector, even if you do not have this manual.
To utilize these manuals, you need to install Adobe Reader on your computer (Windows or Macintosh).
Please download Adobe Reader from the Internet (http://www.adobe.com).
Accessing the PDF Manuals
For Windows:
1 Insert the CD-ROM in the CD-ROM
drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 Double click the language (name of the
folder) that you want to view.
5 Double click the “XR1” pdf file to access
the projector manuals.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM
drive.
2 Double click the “CD-ROM” icon.
3 Double click the language (name of the
folder) that you want to view.
4 Double click the “XR1” pdf file to access
the projector manuals.
Note
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe
Reader first, then specify the desired file using the “File”, “Open” menu.
10
Introduction
Accessories
Supplied accessories
Lithium battery
(CR2025)
UBATL0011TAZZ
Remote control
RRMCGA256WJSA
Soft case
GCASNA011WJZZ
Cable tieK2
UBNDTA015WJZZ
RGB/USB cable
(6' (1.8 m))
QCNWGA047WJPZ
• For the RGB/USB
cable
• For the power cord
• Projector manual CD-ROM
UDSKAA045WJN1
• Operation manual (this manual)
Power cord*
(1)
(2)
For U.S., Canada,
etc.
(6' (1.8 m))
QACCDA029WJPZ
For Europe, except
U.K.
(6' (1.8 m))
QACCVA006WJPZ
(3)
(4)
For U.K., Hong Kong
For Australia, New
and Singapore
Zealand and Oceania
(6' (1.8 m))
(6' (1.8 m))
QACCBA015WJPZ
QACCLA024WJPZ
* Use the power cord that corresponds to the wall outlet in your country.
Optional accessories
■ 3 RCA to 15-pin D-sub cable (9n10o (3.0 m))
■ Lamp unit
AN-C3CP
AN-XR1LP
Note
• Some of the optional accessories may not be available depending on the region. Please check with
your nearest Sharp Authorized Projector Dealer or Service Center.
Carrying the Projector
Tying the Cables
Using the Soft Case
Tie the cable using the supplied
cable ties.
Power cord
RGB/USB cable
Info
• Be sure the projector has cooled down sufficiently before
placing it in the case.
• This soft case is only for storing and carrying the projector.
• Shipping the projector in the soft case as a parcel may cause
damage to the projector. If you send the projector in the carrying case as a parcel, be sure to place it in a sturdy case and
with enough shock absorbing material to avoid any damage.
Note
• You cannot store the supplied
cables within the soft case. When
transporting the projector, prepare a bag for these cables.
11
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
Projector
Top View
Lamp indicator
54
ON/STANDBY button
For turning the power
on and putting the
projector into standby
mode.
26
54
ENTER button
For setting items
selected or adjusted
on the menu.
Adjustment buttons
(W/Y/V/X)
For selecting menu
items.
36
27
Setup Guide indicators
54
Temperature warning
indicator
Volume buttons (V/X)
For adjusting the
speaker sound level.
29
36
36
51
MENU/HELP button
For displaying
adjustment and
setting screens, and
help screen.
29
INPUT button (W/Y)
For switching input mode
1, 2 or 3.
Front View
HEIGHT ADJUST
button
28
Zoom knob
For enlarging/
reducing the
picture.
28
27 Focus ring
For adjusting the
focus.
15 Remote control sensor
Indicators on the Projector
ON/STANDBY button
Normal (Standby)
Green on
Normal (Power on)
Red blinks
Abnormal (See page 54.)
Green on
Normal
Green blinks
The lamp is warming up or shutting down.
Red on
The lamp is shut down abnormally or
requires to be changed. (See page 54.)
Temperature warning
indicator
Off
Normal
Red on
The internal temperature is abnormally
high. (See page 54.)
FOCUS/ZOOM
indicator
HEIGHT ADJUST
indicator
Orange blinks
“1 FOCUS” or “3 ZOOM” is highlighted on
the Setup Guide. (See page 27.)
“2 HEIGHT ADJUST” is highlighted on the
Setup Guide. (See page 27.)
Lamp indicator
12
Red on
Orange blinks
Side View
Terminals Refer to “INPUT Terminals and Connectable Main Equipment” on page 21.
INPUT 1 terminal
23
Terminal for computer
RGB and component
signals.
USB terminal
Terminal connecting
with the USB
terminal on the
computer for using
the supplied remote
control as the
computer mouse.
AC socket
Connect the
supplied Power
cord.
33
24 INPUT 2 terminal
Terminal for connecting video equipment
with an S-video
terminal.
25 INPUT 3 terminal
Terminal for connecting video equipment.
23 AUDIO INPUT
24 terminal
25
25
52 Exhaust vent
Kensington
Security
Standard
connector
28 Rear adjustIntake vent
52
Remote control
sensor
15
ment foot
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for
instructions on how to use it to secure the projector.
13
Introduction
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the topic is explained.
ON/STANDBY button
For turning the power
on and putting the
projector into standby
mode.
26
INPUT 1, 2, and 3
buttons
For switching to the
respective input
modes.
29
AUTO SYNC button
For automatically
adjusting images when
connected to a computer.
32
RESIZE button
For switching the
screen size (NORMAL,
BORDER, etc.).
30
PICTURE MODE
buttons
For switching the
picture mode.
32
Volume buttons
For adjusting the
speaker sound level.
29
36 MENU/HELP button
For displaying adjustment
51 and setting screens, and
help screen.
33 MOUSE/Adjustment
buttons (P/R/O/Q)
36 • For moving the computer
cursor when connecting
the projector USB terminal
to the computer with RGB/
USB cable.
• For selecting menu items.
33 L CLICK/ENTER button
• For the Left click when
36
connecting the projector
USB terminal to the
computer with RGB/USB
cable.
• For setting items selected
or adjusted on the menu.
33 R CLICK/RETURN button
• For the Right click when
36
connecting the projector
Note
• All the buttons on the remote control, except
the MOUSE/Adjustment button, are made of
luminous rubber, that is visible in the dark. (The
luminous light weakens over time.)
USB terminal to the
computer with RGB/USB
cable.
• For undoing an operation
or returning to the previous
display.
32 FREEZE button
For freezing images.
29 AV MUTE button
For temporarily displaying the black screen and
turning off the sound.
Inserting the Lithium Battery
14
1
While pressing the tab (1), pull the battery holder
(2).
2
Pull the battery holder.
3
Insert the supplied lithium battery (CR2025).
4
Insert the battery holder into the remote control.
• Insert the lithium battery with the + side of the battery facing the
+ mark of the battery holder.
+ mark
Front view
30°
The remote control can be used to control the
projector within the ranges shown in the illustration.
Note
• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may
differ depending on the screen material.
When using the remote control
• Be sure not to drop, expose to moisture or
high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the projector away from the fluorescent lamp.
Introduction
Usable Range
Remote control sensor
30°
Remote
control signal
transmitters
13n (4 m)
30°
Remote control
Rear view
Remote control sensor 30°
30°
13n (4 m)
Remote control
signal
30° transmitters
Notes the Use of the Lithium Battery
CAUTION The battery used in this device may present a risk of fire of chemical burn if mistreated. Do not recharge, disassemble, heat above 212°F (100°C) , or incinerate. Replace battery with the type CR2025 only. Use of another battery may present a risk of fire or explosion.
Dispose of used battery promptly. Keep away from children. Do not disassemble and do not
dispose of in fire.
• See page 2 for caution on the lithium battery.
• Do not short-circuit, recharge, disassemble, or heat the lithium battery.
• Should the lithium battery leak, wipe the battery compartment clean, and then insert a new
battery.
Replacement of lithium battery
• Replace with a new battery (CR2025) if remote control operation often fails.
• When disposing the battery, follow the recycling or disposal regulations in your community.
15
Quick Start
This section shows the basic operation (projector connecting with the computer). For details, see
the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
5
INPUT button
4
ENTER button
3
6
4
3
6
ON/STANDBY
button
HEIGHT
ADJUST button
4
Zoom knob
4
Focus ring
ON/STANDBY
button
5
INPUT 1 button
4
ENTER button
1. Place the projector facing a wall or a screen
_P. 18
2. Connect the projector to the computer and plug the power cord
into the AC socket of the projector
When connecting equipment other than the computer, see
pages 24 and 25.
_PP. 21–25
3. Press the ON/STANDBY button to turn the projector on
On the projector
On the remote control
_P. 26
16
4. Adjust the projected image with the Setup Guide
1 After the projector turns on, the Setup
3 Angle (See page 28.)
Guide appears. (When “Setup Guide” is set
to “On”. n page 45)
• Adjust the projector angle using the
HEIGHT ADJUST button.
Quick Start
HEIGHT ADJUST
button
4 Zoom (See page 28.)
• Refer to the Setup Guide screen to adjust
the focus, angle and zoom.
• Press TENTER to finish the Setup Guide.
2 Focus (See page 27.)
• Bring the projected
image into focus
using the focus ring.
Focus ring
• Adjust the projected image size using the
zoom knob.
zoom
in
Zoom knob
zoom
out
5 After adjusting the focus, height and screen
size, press TENTER to finish the Setup
Guide.
_P. 27
5. Select the INPUT mode
Select the “INPUT 1” using the INPUT button on the projector or C INPUT 1 on the remote
control.
On the On the remote On-screen display (RGB)
control
projector
• When pressing the INPUT button on the projector, input mode switches in order of
INPUT1 INPUT2 INPUT3 .
• When using the remote control, press the CINPUT 1/DINPUT 2/EINPUT 3 button to
switch the INPUT mode.
_P. 29
6. Turn the Power off
Press the ON/STANDBY button, then press that button again while the confirmation message is
displayed, to put the projector into standby mode.
On-screen Display
On the
On the remote
projector
control
• While the cooling fan is running, the Adjustment buttons blinks. (When
“Guide LEDs” is set to “On”. n page 48)
• Unplug the power cord from the AC outlet after the cooling fan stops.
_P. 26
17
Setting up the Projector
Setting up the Projector
Position the projector perpendicular to the screen with the projector’s feet flat and level to achieve
an optimal image.
Note
• For an optimal image, position the screen so that it is not in direct sunlight or room light. Light falling
directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim
the lights when setting up the screen in a sunny or bright room.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according
to the desired picture size. (See page 19.)
Example of standard setup
Side View
Screen
H
Lens center
L
Projecting a Reversed Image
Projection from behind the
Screen
■ Place a translucent screen between the projector and the audience.
■ Reverse the image by setting “Rear” in the
“PRJ Mode” menu. (See page 46.)
Translucent screen
Audience
Set to “Front”
Projection Using a Mirror
■ Place a mirror (normal flat type) in front of
the lens.
■ When the translucent screen is placed between the mirror and audience, set to “Front”
in the “PRJ Mode” menu. (See page 46.)
■ When the mirror is placed on the audience
side, set to “Rear” in the “PRJ Mode” menu.
(See page 46.)
18
Set to “Rear”
Mirror
Audience
Translucent
screen
Audience
Mirror
Info
• When using a mirror, be sure to carefully position both the projector and the mirror so the
light does not shine into the eyes of the audience.
Screen Size and Projection Distance (XR-1X)
NORMAL Mode (4:3)
Picture (Screen) size
Diag. [χ ]
Width
Height
Projection distance [L]
Minimum [L1]
Maximum [L2]
Distance from the bottom of the
image to the lens center [H]
ⳮ50.9 cm (ⳮ20 3/64⬙)
270⬙ (686 cm) 549 cm (216⬙)
411 cm (162⬙) 9.9 m (32⬘ 5⬙)
250⬙ (635 cm) 508 cm (200⬙)
381 cm (150⬙) 9.1 m (30⬘ 0⬙)
200⬙ (508 cm) 406 cm (160⬙)
305 cm (120⬙) 7.3 m (24⬘ 0⬙)
8.5 m (28⬘ 0⬙)
ⳮ37.7 cm (ⳮ14
150⬙ (381 cm) 305 cm (120⬙)
229 cm (90⬙)
5.5 m (18⬘ 0⬙)
6.4 m (21⬘ 0⬙)
ⳮ28.3 cm (ⳮ11 9/64⬙)
100⬙ (254 cm) 203 cm (80⬙)
152 cm (60⬙)
3.7 m (12⬘ 0⬙)
4.3 m (14⬘ 0⬙)
ⳮ18.9 cm (ⳮ7
27
84⬙ (213 cm) 171 cm (67⬙)
128 cm (50⬙)
3.1 m (10⬘ 1⬙)
3.6 m (11⬘ 9⬙)
ⳮ15.8 cm (ⳮ6
15
72⬙ (183 cm) 146 cm (58⬙)
110 cm (43⬙)
2.6 m (8⬘ 8⬙)
3.1 m (10⬘ 1⬙)
ⳮ13.6 cm (ⳮ5
11
60⬙ (152 cm) 122 cm (48⬙)
91 cm (36⬙)
2.2 m (7⬘ 2⬙)
2.6 m (8⬘ 5⬙)
ⳮ11.3 cm (ⳮ4
29/64⬙)
40⬙ (102 cm)
81 cm (32⬙)
61 cm (24⬙)
1.5 m (4⬘ 10⬙)
1.7 m (5⬘ 7⬙)
ⳮ7.5 cm (ⳮ2
31/32⬙)
30⬙ (76 cm)
61 cm (24⬙)
46 cm (18⬙)
1.1 m (3⬘ 7⬙)
1.3 m (4⬘ 2⬙)
ⳮ5.7 cm (ⳮ2
15/64⬙)
ⳮ47.1 cm (ⳮ18 9/16⬙)
/64⬙)
/64⬙)
/32⬙)
Setup
χ : Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the bottom of the image to the lens center (cm/in)
/32⬙)
27
The formula for picture size and projection distance
[m/cm]
[Feet/inches]
L1 (m) = 0.03658χ
L1 (ft) = 0.03658χ / 0.3048
L2 (m) = 0.04267χ
L2 (ft) = 0.04267χ / 0.3048
H (cm) = - 0.18857χ
H (in) = - 0.18857χ / 2.54
STRETCH Mode (16:9)
Picture (Screen) size
Diag. [χ ]
Width
Height
Projection distance [L]
Minimum [L1]
Maximum [L2]
250⬙ (635 cm) 553 cm (218⬙)
311 cm (123⬙) 10.0 m (32⬘ 8⬙)
225⬙ (572 cm) 498 cm (196⬙)
280 cm (110⬙)
9.0 m (29⬘ 5⬙)
Distance from the bottom of the Adjustable range of
image to the lens center [H]
image position [S]
21
/32⬙)
Ⳳ51.9 cm (Ⳳ20
27
ⳮ92.9 cm (ⳮ36
37/64⬙)
Ⳳ46.7 cm (Ⳳ18
25/64⬙)
/64⬙)
11
ⳮ103.2 cm (ⳮ40
/64⬙)
/32⬙)
200⬙ (508 cm) 443 cm (174⬙)
249 cm (98⬙)
8.0 m (26⬘ 2⬙)
9.3 m (30⬘ 6⬙)
ⳮ82.6 cm (ⳮ32
33
Ⳳ41.5 cm (Ⳳ16
150⬙ (381 cm) 332 cm (131⬙)
187 cm (74⬙)
6.0 m (19⬘ 7⬙)
7.0 m(22⬘11⬙)
ⳮ61.9 cm (ⳮ24
25/64⬙)
Ⳳ31.1 cm (Ⳳ12 1/4⬙)
133⬙ (338 cm) 294 cm (116⬙)
166 cm (65⬙)
5.3 m (17⬘ 5⬙)
6.2 m (20⬘ 3⬙)
ⳮ54.9 cm (ⳮ21 5/8⬙)
106⬙ (269 cm) 235 cm (92⬙)
132 cm (52⬙)
4.2 m(13⬘10⬙)
4.9 m (16⬘ 2⬙)
ⳮ43.8 cm (ⳮ17
15/64⬙)
Ⳳ22.0 cm (Ⳳ8
21/32⬙)
100⬙ (254 cm) 221 cm (87⬙)
125 cm (49⬙)
4.0 m (13⬘ 1⬙)
4.6 m (15⬘ 3⬙)
ⳮ41.3 cm (ⳮ16
17
/64⬙)
Ⳳ20.8 cm (Ⳳ8
11
92⬙ (234 cm) 204 cm (80⬙)
115 cm (45⬙)
3.7 m (12⬘ 0⬙)
4.3 m (14⬘ 0⬙)
ⳮ38.0 cm (ⳮ14
61/64⬙)
Ⳳ19.1 cm (Ⳳ7
33/64⬙)
84⬙ (213 cm) 186 cm (73⬙)
105 cm (41⬙)
3.3 m (11⬘ 0⬙)
3.9 m(12⬘10⬙)
ⳮ34.7 cm (ⳮ13
21
/32⬙)
Ⳳ17.4 cm (Ⳳ6
55
72⬙ (183 cm) 159 cm (63⬙)
90 cm (35⬙)
2.9 m (9⬘ 5⬙)
3.3 m (11⬘ 0⬙)
ⳮ29.7 cm (ⳮ11
45/64⬙)
Ⳳ14.9 cm (Ⳳ5
57/64⬙)
60⬙ (152 cm) 133 cm (52⬙)
75 cm (29⬙)
2.4 m (7⬘10⬙)
2.8 m (9⬘ 2⬙)
ⳮ24.8 cm (ⳮ9 3/4⬙)
Ⳳ12.5 cm (Ⳳ4
29
40⬙ (102 cm)
89 cm (35⬙)
50 cm (20⬙)
1.6 m (5⬘ 3⬙)
1.9 m (6⬘ 1⬙)
ⳮ16.5 cm (ⳮ6 1/2⬙)
Ⳳ8.3 cm (Ⳳ3
17/64⬙)
30⬙ (76 cm)
66 cm (26⬙)
37 cm (15⬙)
1.2 m (3⬘11⬙)
1.4 m (4⬘ 7⬙)
ⳮ12.4 cm (ⳮ4 7/8⬙)
Ⳳ6.2 cm (Ⳳ2
29
χ : Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the bottom of the image to the lens center (cm/in)
S: Adjustable range of image position (cm/in) See page 43.
Ⳳ27.6 cm (Ⳳ10 7/8⬙)
/64⬙)
/64⬙)
/32⬙)
/64⬙)
The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1 (ft) = 0.03985χ / 0.3048
L1 (m) = 0.03985χ
L2 (ft) = 0.04649χ / 0.3048
L2 (m) = 0.04649χ
H (in) = - 0.41299χ / 2.54
H (cm) = - 0.41299χ
χ
S (in) = ±0.20754χ / 2.54
S (cm) = ±0.20754
Note
• There may be an error of ±3% in the above values.
• Values with a minus (-) sign indicate that the lens center is lower than the bottom of the projected
image.
19
Setting up the Projector (Continued)
Screen Size and Projection Distance (XR-1S)
NORMAL Mode (4:3)
Picture (Screen) size
Diag. [χ ]
Width
Height
Projection distance [L]
Minimum [L1]
Maximum [L2]
Distance from the bottom of the
image to the lens center [H]
ⳮ61.5 cm (ⳮ24 7/32⬙)
280⬙ (711 cm) 569 cm (224⬙)
427 cm (168⬙) 9.8 m (32⬘ 2⬙)
250⬙ (635 cm) 508 cm (200⬙)
381 cm (150⬙) 8.8 m (28⬘ 9⬙)
200⬙ (508 cm) 406 cm (160⬙)
305 cm (120⬙) 7.0 m (23⬘ 0⬙)
8.1 m (26⬘ 8⬙)
ⳮ43.9 cm (ⳮ17
19
/64⬙)
150⬙ (381 cm) 305 cm (120⬙)
229 cm (90⬙)
5.3 m (17⬘ 3⬙)
6.1 m (20⬘ 0⬙)
ⳮ33.0 cm (ⳮ12
31
/32⬙)
100⬙ (254 cm) 203 cm (80⬙)
152 cm (60⬙)
3.5 m (11⬘ 6⬙)
4.1 m (13⬘ 4⬙)
ⳮ22.0 cm (ⳮ8
21
/32⬙)
84⬙ (213 cm) 171 cm (67⬙)
128 cm (50⬙)
2.9 m (9⬘ 8⬙)
3.4 m (11⬘ 2⬙)
ⳮ18.5 cm (ⳮ7
17
/64⬙)
72⬙ (183 cm) 146 cm (58⬙)
110 cm (43⬙)
2.5 m (8⬘ 3⬙)
2.9 m (9⬘ 7⬙)
ⳮ15.8 cm (ⳮ6
15
/64⬙)
60⬙ (152 cm) 122 cm (48⬙)
91 cm (36⬙)
2.1 m (6⬘ 11⬙)
2.4 m (8⬘ 0⬙)
ⳮ13.2 cm (ⳮ5 3/16⬙)
40⬙ (102 cm)
81 cm (32⬙)
61 cm (24⬙)
1.4 m (4⬘ 7⬙)
1.6 m (5⬘ 4⬙)
ⳮ8.8 cm (ⳮ3
29/64⬙)
30⬙ (76 cm)
61 cm (24⬙)
46 cm (18⬙)
1.1 m (3⬘ 5⬙)
1.2 m (4⬘ 0⬙)
ⳮ6.6 cm (ⳮ2
19/32⬙)
ⳮ54.9 cm (ⳮ21 5/8⬙)
χ : Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the bottom of the image to the lens center (cm/in)
The formula for picture size and projection distance
[m/cm]
[Feet/inches]
L1 (m) = 0.03503χ
L1 (ft) = 0.03503χ / 0.3048
L2 (m) = 0.04064χ
L2 (ft) = 0.04064χ / 0.3048
H (cm) = - 0.21971χ
H (in) = - 0.21971χ / 2.54
STRETCH Mode (16:9)
Picture (Screen) size
Diag. [χ ]
Width
Height
Projection distance [L]
Minimum [L1]
Maximum [L2]
Distance from the bottom of the Adjustable range of
image to the lens center [H]
image position [S]
Ⳳ54.0 cm (Ⳳ21 1/4⬙)
260⬙ (660 cm) 576 cm (227⬙)
324 cm (127⬙)
9.9 m (32⬘ 7⬙)
ⳮ116.2 cm (ⳮ45 3/4⬙)
250⬙ (635 cm) 553 cm (218⬙)
311 cm (123⬙)
9.5 m (31⬘ 4⬙)
ⳮ111.7 cm (ⳮ43
63/64⬙)
Ⳳ51.9 cm (Ⳳ20
27/64⬙)
225⬙ (572 cm) 498 cm (196⬙)
280 cm (110⬙)
8.6 m (28⬘ 2⬙) 10.0 m (32⬘ 8⬙) ⳮ100.6 cm (ⳮ39
19/32⬙)
Ⳳ46.7 cm (Ⳳ18
25/64⬙)
200⬙ (508 cm) 443 cm (174⬙)
249 cm (98⬙)
7.6 m (25⬘ 1⬙)
8.9 m (29⬘ 1⬙)
ⳮ89.4 cm (ⳮ35 3/16⬙)
Ⳳ41.5 cm (Ⳳ16
11/32⬙)
150⬙ (381 cm) 332 cm (131⬙)
187 cm (74⬙)
5.7 m (18⬘ 9⬙)
6.6 m (21⬘ 9⬙)
ⳮ67.0 cm (ⳮ26
25/64⬙)
Ⳳ31.1 cm (Ⳳ12 1/4⬙)
133⬙ (338 cm) 294 cm (116⬙)
166 cm (65⬙)
5.1 m (16⬘ 8⬙)
5.9 m (19⬘ 4⬙)
ⳮ59.4 cm (ⳮ23
13/32⬙)
Ⳳ27.6 cm (Ⳳ10 7/8⬙)
106⬙ (269 cm) 235 cm (92⬙)
132 cm (52⬙)
4.0 m (13⬘ 3⬙)
4.7 m (15⬘ 5⬙)
ⳮ47.4 cm (ⳮ18
21/32⬙)
Ⳳ22.0 cm (Ⳳ8
21/32⬙)
100⬙ (254 cm) 221 cm (87⬙)
125 cm (49⬙)
3.8 m (12⬘ 6⬙)
4.4 m (14⬘ 6⬙)
ⳮ44.7 cm (ⳮ17
19/32⬙)
Ⳳ20.8 cm (Ⳳ8
11/64⬙)
92⬙ (234 cm) 204 cm (80⬙)
115 cm (45⬙)
3.5 m (11⬘ 6⬙)
4.1 m (13⬘ 4⬙)
ⳮ41.1 cm (ⳮ16 3/16⬙)
Ⳳ19.1 cm (Ⳳ7
33/64⬙)
84⬙ (213 cm) 186 cm (73⬙)
105 cm (41⬙)
3.2 m (10⬘ 6⬙)
3.7 m (12⬘ 2⬙)
ⳮ37.5 cm (ⳮ14
25/32⬙)
Ⳳ17.4 cm (Ⳳ6
55/64⬙)
72⬙ (183 cm) 159 cm (63⬙)
90 cm (35⬙)
2.7 m (9⬘ 0⬙)
3.2 m (10⬘ 6⬙)
ⳮ32.2 cm (ⳮ12
43/64⬙)
Ⳳ14.9 cm (Ⳳ5
57/64⬙)
60⬙ (152 cm) 133 cm (52⬙)
75 cm (29⬙)
2.3 m (7⬘ 6⬙)
2.7 m (8⬘ 9⬙)
ⳮ26.8 cm (ⳮ10 9/16⬙)
Ⳳ12.5 cm (Ⳳ4
29/32⬙)
40⬙ (102 cm)
89 cm (35⬙)
50 cm (20⬙)
1.5 m (5⬘ 0⬙)
1.8 m (5⬘ 10⬙) ⳮ17.9 cm (ⳮ7 1/32⬙)
Ⳳ8.3 cm (Ⳳ3
17/64⬙)
30⬙ (76 cm)
66 cm (26⬙)
37 cm (15⬙)
1.1 m (3⬘ 9⬙)
1.3 m (4⬘ 4⬙)
ⳮ13.4 cm (ⳮ5 9/32⬙)
Ⳳ6.2 cm (Ⳳ2
29/64⬙)
χ : Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the bottom of the image to the lens center (cm/in)
S: Adjustable range of image position (cm/in) See page 43.
The formula for picture size and projection distance
[Feet/inches]
[m/cm]
L1 (ft) = 0.038169χ / 0.3048
L1 (m) = 0.038169χ
L2 (ft) = 0.044276χ / 0.3048
L2 (m) = 0.044276χ
H (in) = - 0.44691χ / 2.54
H (cm) = - 0.44691χ
S (in) = ±0.20754χ / 2.54
S (cm) = ±0.20754χ
Note
• There may be an error of ±3% in the above values.
• Values with a minus (-) sign indicate that the lens center is lower than the bottom of the projected
image.
20
Connections
INPUT Terminals and Connectable Main Equipment
INPUT 1 terminal
■ Connecting the computer. (See page 23.)
■ Connecting video
equipment with
component output
terminal (DVD player,
DTV decoder, DVD
recorder with hard disc,
etc.). (See page 24.)
INPUT 2 terminal
Connecting video equipment
with S-video output terminal
(VCR, DVD player, etc.). (See
page 24.)
INPUT 3 terminal
Connecting video equipment
without S-video output
terminal. (See page 25.)
Connections
USB terminal
Connecting the computer.
(See page 33.)
AUDIO INPUT terminal
Connecting an audio
cable (Shared audio
input terminal for INPUT
1, 2 and 3.) (See pages
23, 24 and 25.)
21
Samples of Cables for Connection
• For more details of connection and cables, refer to the opeation manual of the connecting equipment.
• You may need other cables or connectors not listed above.
Equipment
Computer
Input
Signal
RGB/USB cable (supplied)
Terminal on the
projector
INPUT1
ø3.5 mm stereo audio cable
AUDIO INPUT
3 RCA (Component) to 15-pin D-sub cable
(optional, AN-C3CP)
INPUT1
S-video cable (commercially available)
INPUT2
Video cable (commercially available)
INPUT3
ø3.5 mm minijack to RCA audio cable
(commercially available)
AUDIO INPUT
Cable
RGB
video
Computer
audio
Audio-visual
equipment
Component
video
S-video
Video
Audio
Camera/video
game
Component
video
Cables for a camera or a video game/3 RCA INPUT1
(Component) to 15-pin D-sub cable (optional,
AN-C3CP)
Cable adapter (commercially available)
S-video
Video
Audio
22
Cables for a camera
or a video game
INPUT2
Cables for a camera
or a video game
INPUT3
Cables for a camera or a video game/ø3.5
AUDIO INPUT
mm minijack to RCA audio cable (commercially available)
Cable adapter (commercially available)
Connecting to a Computer
Before connecting, be sure to unplug the power cord of the projector from the AC outlet and
turn off the devices to be connected. After making all connections, turn on the projector
and then the other devices. When connecting a computer, be sure that it is the last device to
be turned on after all the connections are made.
Be sure to read the operation manuals of the devices to be connected before making connections.
Supplied
accessory
RGB/USB Cable
To audio output terminal
To RGB output terminal
To USB terminal
To INPUT1
To AUDIO
terminal
INPUT terminal
To USB terminal
Connections
* ø3.5 mm stereo or
mono audio cable
(commercially
available or
available as Sharp
service part
QCNWGA038WJPZ)
RGB/USB Cable
* When using the ø3.5 mm mono audio cable, the volume level will be half of
when using the ø3.5 mm stereo audio cable.
Note
• When connecting with USB cable, you can use the remote control as a mouse for controlling cursor.
See page 33.
• See page 59 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the signal
output setting of the computer is switched to the external output. Refer to the computer operation manual for switching the computer signal output settings.
“Plug and Play” function (when connecting to a 15-pin terminal)
■ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA
DDC compatible computer will communicate their setting requirements, allowing for quick
and easy setup.
■ Before using the “Plug and Play” function, be sure to turn on the projector first and the
connected computer last.
Note
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a
VESA DDC compatible computer.
23
Connecting to Video Equipment
The projector has a COMPUTER/COMPONENT terminal, an S-VIDEO terminal and a VIDEO terminal for video input. See the illustration below to connect with the audio-visual equipment.
The image quality is highest in order of the component signal, the S-video signal and the video
signal. If your audio-visual equipment has a component output terminal, use the COMPUTER/
COMPONENT terminal (INPUT1) on the projector for video connection.
When using a 3 RCA (Component) to 15-pin D-sub cable
To audio output terminal
To component output (Y, CB/PB, CR/PR) terminal
To INPUT1
terminal
To AUDIO
INPUT terminal
3 RCA (Component) to
15-pin D-sub cable
(optional: AN-C3CP)
ø3.5 mm minijack to RCA
audio cable (commercially
available)
When using an S-video cable
To audio output terminal
To S-video output terminal
To INPUT2
To AUDIO
terminal
INPUT terminal
ø3.5 mm minijack to RCA
audio cable (commercially
available)
24
S-video cable
(commercially available)
When using a composite video cable
To audio output terminal
To video output terminal
To INPUT3
To AUDIO
terminal
INPUT terminal
ø3.5 mm minijack to RCA
audio cable (commercially
available)
Composite video cable
(commercially available)
Connections
Note
• ø3.5 mm minijack to RCA audio cable (commercially available) is required for audio input.
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the side of the projector.
AC socket
25
Turning the Projector On/Off
Info
Turning the Projector on
Before performing the steps in this section,
connect any equipment that you use with
the projector. (See pages 23, 24 and 25.)
Also connect the power cord to the projector. (See page 25.)
Press SON/STANDBY on the projector or
AON/STANDBY on the remote control.
• English is the factory default language. If you
want to change the on-screen display to another
language, change the language according to
the procedure on page 46.
ON/STANDBY button
Lamp indicator
• When the lamp is warming up, the Adjustment buttons blink in a clockwise direction. (When “Guide
LEDs” is set to “On”. n page 48)
• When System Lock is set, the keycode input box
appears. Enter the right keycode to start projection. See page 49 for details.
Note
• About the Lamp Indicator
The lamp indicator lights up or blinks, indicating the status of the lamp.
Green: The lamp is ready.
Blinking in green: The lamp is warming up or shutting down.
Red: The lamp is shut down abnormally or the
lamp should be replaced.
• When switching on the projector, a slight flickering of the
image may be experienced within the first minute after the
lamp has been illuminated. This is normal operation as the
lamp’s control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.
• If the projector is put into standby mode and immediately
turned on again, the lamp may take some time to start projection.
ON/STANDBY
button
On-screen Display (confirmation message)
Turning the Power off (Putting
the Projector into Standby Mode)
1
2
26
Press SON/STANDBY on the projector or AON/STANDBY on the
remote control, then press that button again while the confirmation
message is displayed, to put the
projector into standby mode.
Unplug the power cord from the AC
outlet after the cooling fan stops.
• When the projector is turned off, the Adjustment buttons blink in a counterclockwise direction. (When “Guide LEDs” is set
to “On”. n page 48)
R
Info
• Do not unplug the power cord during projection
or cooling fan operation. This can cause damage due to rise in internal temperature, as the
cooling fan also stops.
Image Projection
About the Setup Guide
Setup Guide screen
After turning on the projector, the Setup
Guide screen appears to assist you with
projector setup.
Guidance items
1 FOCUS
2 HEIGHT ADJUST
3 ZOOM
Adjust the projector by following the illuminated buttons or Setup Guide indicators.
Press TENTER to turn off the Setup
Guide screen.
Note
• The Setup Guide screen automatically highlights the items in order of
1 FOCUS 2 HEIGHT ADJUST 3 ZOOM 4 ENTER .
• You can adjust the focus, height or zoom anytime you want, regardless of the selection on
the Setup Guide.
• If you do not want to display the Setup Guide
for the next time, set “Menu” - “SCR - ADJ” “Setup Guide” to “Off”. (See page 45.)
Setup Guide
indicator
ON/STANDBY
button
ENTER button
Basic
Operation
Adjusting the Projected Image
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Rotate the focus ring to adjust the focus while watching the projected image.
Focus ring
27
Image Projection (Continued)
2 Adjusting the Height
HEIGHT
ADJUST button
The height of the projector can be adjusted using the adjustment feet at the
front and rear of the projector.
When the screen is in a higher position
than the projector, the projection image
can be made higher by adjusting the
projector.
1
Lift the projector to adjust its
height while pressing the HEIGHT
ADJUST button.
2
Remove your hands from the
HEIGHT ADJUST button of the
projector after its height has been
finely adjusted.
• The angle of projection is adjustable up
to 7.5 degrees from the surface on which
the projector is placed.
3
Use the rear adjustment foot to
make the projector level.
• The projector is adjustable ±1 degree
from the standard position.
Note
• When adjusting the height of the projector,
trapezoidal distortion occurs. When “Auto
Keystone” is set to “On”, keystone correction
functions automatically to correct trapezoidal
distortion. When you want to adjust the automatically corrected image, use the manual
keystone correction. (See page 44.)
Rear adjustment foot
Info
• Do not apply too much pressure on the projector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
3 Adjusting the Screen Size
You can adjust the screen size using
the zoom knob on the projector.
zoom
in
Zoom Knob
28
zoom
out
Switching the Input Mode
INPUT
buttons
Select the appropriate input mode for
the connected equipment.
AV MUTE button
PressC INPUT 1, D INPUT 2 or
EINPUT 3 on the remote control to select the input mode.
Volume buttons
• When pressing INPUT (W/Y) on the projector,
input mode switches in order of
INPUT1 INPUT2 INPUT3 .
• When “Auto Search” is set to “On”, INPUT (W/
Y) on the projector functions as the Auto Search
buttons. (See page 47.)
Adjusting the Volume
Press K/L on the remote control or
V/X on the projector to adjust the volume.
On-screen Display
Note
• Pressing K/V will lower the volume.
• Pressing L/X will raise the volume.
Basic
Operation
Displaying the Black Screen
and Turning off the Sound
Temporarily
Press MAV MUTE on the remote control to temporarily display a black
screen and turn off the sound.
On-screen Display
Note
• Pressing MAV MUTE again will turn the projected image back on.
29
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.
Press HRESIZE.
• See page 43 for setting on menu screen.
RESIZE button
Computer
NORMAL
4:3 aspect ratio
SVGA (800 K 600)
XGA (1024 K 768)
SXGA (1280 K 960)
SXGA L (1400 K 1050)
Other aspect ratios
SXGA (1280 K 1024)
1280 K 720
BORDER
XR-1S
XR-1X
XR-1S
XR-1X
XR-1S
1024 K 768
800 K 600
768 K 576
600 K 450
1024 K 576
800 K 450
1024 K 768
800 K 600
768 K 576
600 K 450
1024 K 576
800 K 450
J
J
J
J
1024 K 576
800 K 450
Output screen image
Input Signal
Computer
XR-1X
XR-1S
Resolution
lower than
XGA
Resolution
lower than
SVGA
XGA
SVGA
STRETCH
XR-1X
Image type
NORMAL
BORDER
STRETCH
4:3 aspect ratio
Resolution
higher than
XGA
Resolution
higher than
SVGA
SXGA
(1280K1024)
5:4 aspect ratio
1280K720
16:9 aspect ratio
* Mode for projecting an image with the original
aspect ratio without cutting any portions.
30
: Cutout area on which images cannot be projected.
VIDEO
• “STRETCH” is fixed when 540P, 720P or 1080I signals are entered.
Input Signal
DVD / Video
Output screen image
Image type
NORMAL
BORDER
STRETCH
4:3 aspect ratio
480I, 480P, NTSC,
PAL, SECAM
Letter box
Squeezed 16:9 image
Squeezed 4:3 image
16:9 aspect ratio
16:9 aspect ratio
(4:3 aspect ratio in
16:9 screen)
Basic
Operation
540P, 720P, 1080I
(16:9)
* Mode for projecting an image with the original aspect ratio without cutting any portions.
: Cutout area on which images cannot be projected.
: Area on which the image is not included in the original signals.
31
Adjusting/Operating with the Remote Control
Auto Sync (Auto Sync Adjustment)
Auto Sync function works when detecting input signal after the projector turns
on.
Press FAUTO SYNC to manually adjust with Auto Sync function.
Note
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help menu
for manual adjustments. (See page 51.)
Freezing a Moving Image
1
2
Press NFREEZE.
• The projected image is frozen.
Press NFREEZE again to return
to the moving image from the currently connected device.
Selecting the Picture Mode
You can select the suitable picture
mode for the projected image, such as
movie or video game.
Press GPICTURE MODE.
• When pressing GPICTURE MODE, the picture
mode changes in order of
Standard Presentation Cinema Game .
Note
• See page 40 for details on the picture mode.
32
AUTO SYNC
button
FREEZE button
PICTURE MODE
button
Using Mouse Function
When connecting the projector and computer with the USB terminals, you can
use the remote control as the computer mouse.
Supplied
accessory
To RGB output terminal
RGB/USB Cable
To USB terminal
To USB terminal
To INPUT1 terminal
RGB/USB Cable
1
Connect the projector and the
computer with the supplied RGB/
USB cable.
2
Use the mouse functions.
Note
• you can not use this function when displaying
the menu screen.
MOUSE/Adjuatment
button (P/R/O/Q)
L CLICK button
R CLICK button
Useful
Features
• MOUSE/Adjustment button (P/R/O/Q)
functions to move cursor.
• IL CLICK button functions as the left
click.
• JR CLICK button functions as the right
click.
• IL CLICK and JR CLICK have common function when your computer supports only a one-click mouse, such as
Macintosh.
Computer mouse
33
Menu Items
The following shows the items that can be set in the projector.
Main menu
“Picture” menu
Picture
Page 40
Sub menu
Standard
Presentation
Cinema
Game
Picture Mode
Page 40
INPUT 1 (RGB)
Picture
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
SCR - ADJ
PRJ - ADJ
Help
Standard
0
0
0
0
7500K
Off
Off
Contrast
-30
+30
Bright
-30
+30
Red
-30
+30 *1
Blue
-30
+30 *1
Color
-30
+30 *2
Tint
-30
+30 *2
Sharp
-30
+30 *2
Page 40
5500K
6500K
7500K
8500K
9300K
10500K
CLR Temp
Page 41
SEL./ADJ.
ENTER
END
Bright Boost [On/Off]
Page 41
INPUT 1 (Component)/INPUT 2/INPUT 3
Progressive
Picture
Picture Mode
Contrast
Bright
Color
Tint
Sharp
CLR Temp
Bright Boost
Progressive
Reset
SEL./ADJ.
SCR - ADJ
PRJ - ADJ
Help
Standard
sRGB [On/Off]
0
0
0
0
0
7500K
*1 Items when inputting RGB signal through
INPUT 1
*2 Items when inputting component signal
through INPUT 1, or when selecting INPUT
2 or INPUT 3
Off
3D Progressive
ENTER
END
Main menu
Page 43
Sub menu
Normal
Border
Stretch
Resize
Page 43
Image Shift
[XR-1X]
[XR-1S]
SEL./ADJ.
*1
Reset
“SCR - ADJ” menu
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
2D Progressive
3D Progressive
Film Mode
Page 42
SCR - ADJ
Picture
*2
Page 42
SCR - ADJ
PRJ - ADJ
Help
+96
+75
Keystone
Normal
[XR-1X]
[XR-1S]
0
0
-127
-100
+127
+100
Page 44
Off
On
Logo
On
Front
English
ENTER
-96
-75
Page 43
Auto Keystone [On/Off]
Page 44
OSD Display [On/Off]
Page 44
Background
Page 45
END
Logo
Blue
None
Setup Guide [On/Off]
Page 45
• You can adjust the menu items with icons (
and
) using the respective buttons on the
remote control.
PRJ Mode
Page 46
Language
Page 46
34
Front
Front + Rotate
Rear
Rear + Rotate
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
Main menu
“PRJ - ADJ” menu
PRJ - ADJ
Page 47
Picture
SCR - ADJ
PRJ - ADJ
Eco/Quiet Mode
Auto Search
Auto Power Off
Guide LEDs
System Sound
System Lock
Help
Sub menu
Eco/Quiet Mode [On/Off]
Page 47
Auto Search [On/Off]
Page 47
On
On
On
On
On
Auto Power Off [On/Off]
Page 48
Guide LEDs [On/Off]
Page 48
System Sound [On/Off]
Page 50
System Lock
Lamp Timer(Life)
SEL./ADJ.
0 h
ENTER
100%
Page 49
END
“Help” menu
Picture
SCR - ADJ
Lamp Timer(Life)
Page 50
The items you can set with “Help”
menu
PRJ - ADJ
Help
Reset all adjustments to default settings
ENTER
END
“Help” menu n Page 51
• Vertical stripes or flickering image appear
Auto Sync
Adjust vertical noise
Adjust horizontal noise
• Data image is not centered
Auto Sync
H-Pos
V-Pos
• Color is faded or poor
INPUT 1
Signal type: Auto/RGB/Component
INPUT 2 or INPUT 3
Video System: A u t o / P A L / S E C A M /
NTSC3.58/NTSC4.43/PALM/PAL-N/PAL-60
* The selectable items vary depending on the input signal and the selected input mode.
Useful
Features
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
SEL.
Old Code
New Code
Reconfirm
35
Using the Menu Screen
The menu can be operated to achieve two functions, adjustment and setting. (For setting the menu
items, see pages 38 and 39.)
Operating with the projector
When “PRJ - ADJ” - “Guide LEDs” is set to “On”, the buttons used for menu adjustment on the
projector light up.
Example: When W, Y and the MENU/HELP button light up on the projector, you can use those
buttons for operation.
Adjustment buttons (W/Y/V/X)
MENU/HELP button
ENTER button
MENU/HELP
button
MOUSE Adjustment
button (P/R/O/Q)
ENTER button
RETURN button
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
1
Press BMENU.
2
Press Q or O to display the other
menu screen.
• The “Picture” menu screen for the selected input mode is displayed.
• The selected menu item is highlighted.
Example: “Picture” screen menu for INPUT 1
(RGB) mode
Menu item
Picture
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
SEL./ADJ.
36
SCR - ADJ
PRJ - ADJ
Help
Standard
0
0
0
0
7500K
Off
Off
ENTER
END
3
Press P or R to select the item you
want to adjust.
• The selected item is highlighted.
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
PRJ - ADJ
Help
Standard
0
0
0
0
7500K
Off
Off
SEL./ADJ.
Single ADJ
END
Single adjustment items
Picture
SCR - ADJ
Resize
Image Shift
Keystone
Auto Keystone
PRJ - ADJ
Help
Normal
0
0
Off
To adjust the projected
image while watching it
Press IENTER.
• The selected single adjustment item (e.g.
“Bright”) appears instead of the menu.
• When pressing P or R, the following item
(“Red” after “Bright”) will be displayed.
Picture
Bright
SEL./ADJ.
0
Rtn. Menu
END
Note
• Press IENTER to return to the previous screen.
4
Press O or Q to adjust the item
selected.
• The adjustment is stored.
Picture
SEL./ADJ.
5
SCR - ADJ
PRJ - ADJ
Help
Standard
0
15
0
0
7500K
Useful
Features
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
Off
Off
Single ADJ
END
Press BMENU.
• The menu screen will disappear.
Note
• Press IRETURN to return to the previous screen when the menu is displayed.
37
Using the Menu Screen (Continued)
The menu can be operated to achieve two functions, adjustment and setting. (For adjusting the
menu items, see pages 36 and 37.)
MENU/HELP
button
MOUSE Adjustment
button (P/R/O/Q)
ENTER button
RETURN button
Menu Selections (Settings)
Example: Setting “Background”.
•This operation can also be performed by using the buttons on the projector.
1
Press BMENU.
2
Press O or Q to display the other
menu screen.
• The “Picture” menu screen for the selected input mode is displayed.
Example: “Picture” screen menu for INPUT 1
(RGB) mode
Menu item
Picture
• The selected menu item is highlighted.
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
SEL./ADJ.
38
SCR - ADJ
PRJ - ADJ
Help
Standard
0
0
0
0
7500K
Off
Off
ENTER
END
3
Press P or R to select the item you
want to set, and then press
IENTER or Q to display the sub
menu.
•The selected item is highlighted.
Note
• Press JRETURN or O to return to the
previous screen.
4
Press P or R select the setting of
the item displayed in the sub
menu.
Picture
Picture
SEL./ADJ.
Press IENTER.
6
Press BMENU.
PRJ - ADJ
Help
Normal
0
0
Off
On
Logo
Blue
None
On
Front
English
SEL./ADJ.
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
5
SCR - ADJ
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
ENTER
SCR - ADJ
END
PRJ - ADJ
Help
Normal
0
0
Off
On
Logo
Blue
None
On
Front
English
ENTER
END
• The menu screen will disappear.
Useful
Features
39
Picture Adjustment (“Picture” menu)
You can adjust the projector’s picture to your preferences using the “Picture” menu.
Selecting the Picture mode
Adjusting the Image
Menu operation n Page 38
Menu operation n Page 36
Q Example: “Picture” screen menu for
INPUT 1 (RGB) mode
Q Example: “Picture” screen menu for
INPUT 1 (RGB) mode
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
PRJ - ADJ
Help
0
0
0
0
7500K
Off
Off
SEL./ADJ.
ENTER
END
Description of Items
Selectable items
Standard
Picture
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
Standard
SCR - ADJ
PRJ - ADJ
Help
Standard
0
0
0
0
7500K
Off
Off
SEL./ADJ.
ENTER
END
Description of Adjustment Items
Description
For standard image
Adjustment
Items
O button
Q button
Contrast
For less
contrast.
For more
contrast.
Bright
For less
brightness.
For more
brightness.
Presentation
Brightens darker portions of
image for more enhanced
presentations.
Cinema
Gives greater depth to darker
portions of image for a more
exciting theater experience.
Red*1
For weaker red.
For stronger red.
Blue*1
For natural color gradation for
playing a game, etc.
For weaker
blue.
For stronger
blue.
Color*2
For less color
intensity.
For more color
intensity.
Tint*2
For making skin
tones purplish.
For making skin
tones greenish.
Sharp*2
For less
sharpness.
For more
sharpness.
Game
Note
• You can also press GPICTURE MODE on the
remote control to select the picture mode. (See
page 32.)
*1 Not adjustable/selectable when you set “sRGB”
menu item to “On”, or the input signal is
component.
*2 Not displayed in the RGB input mode.
Note
• To reset all adjustment items, select “Reset”
and press IENTER.
40
Adjusting the Color Temperature Emphasizing the Contrast
This function emphasizes the bright portions of
images to obtain a higher contrast image.
Menu operation n Page 36
Menu operation n Page 38
Q Example: “Picture” screen menu for
INPUT 1 (RGB) mode
Q Example: “Picture” screen menu for
INPUT 1 (RGB) mode
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
SEL./ADJ.
PRJ - ADJ
Help
Standard
0
0
0
0
7500K
Off
Off
ENTER
Picture
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
END
Note
• Values on “CLR Temp” are only for general
standard purposes.
• “CLR Temp” cannot be set when “sRGB” is
set to “On”.
SEL./ADJ.
SCR - ADJ
PRJ - ADJ
Help
Standard
0
0
0
0
7500K
Off
Off
ENTER
END
Note
• When using this function, the image color may
become pale or the tint may be inappropriate.
• “Bright Boost” cannot be set when “sRGB” is
set to “On”.
Description of Items
Selectable
items
5500K
6500K
7500K
For lower color temperature for
warmer, reddish incandescent-like
images.
P
R
9300K
10500K
For higher color temperature for
cooler, bluish, fluorescent-like images.
Useful
Features
8500K
Description
41
Picture Adjustment (“Picture” menu) (Continued)
Progressive
sRGB Setting
Menu operation n Page 38
Menu operation n Page 38
Q Example: “Picture” screen menu for
INPUT 2 mode
Q Example: “Picture” screen menu for
INPUT 1 (RGB) mode
Picture
SCR - ADJ
Picture Mode
Contrast
Bright
Color
Tint
Sharp
CLR Temp
Bright Boost
Progressive
Reset
SEL./ADJ.
PRJ - ADJ
Help
Standard
0
0
0
0
0
7500K
Off
3D Progressive
ENTER
END
Picture
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
Bright Boost
sRGB
Reset
SEL./ADJ.
SCR - ADJ
PRJ - ADJ
Help
Standard
0
0
0
0
7500K
Off
Off
ENTER
END
Description of Items
Selectable
items
Description
2D
Useful to display fast-moving images
Progressive such as sports and action films.
3D
Useful to display relatively slowProgressive moving images such as drama and
documentary more clearly.
Film Mode
Reproduces the image of film source*
clearly. Displays the optimized image of
film transformed with three-two pull down
(NTSC and PAL60Hz) or two-two pull
down (PAL50Hz and SECAM) enhancement to progressive mode images.
* The film source is a digital video recording with the
original encoded as is at 24 frames/second. The
projector can convert this film source to progressive video at 60 frames/second with NTSC and
PAL60Hz or at 50 frames/second with PAL50Hz
and SECAM to play back a high-definition image.
Note
• In NTSC or PAL60Hz, even if the 3D Progressive mode has been set, the three-two pull
down enhancement will be enabled automatically when the film source has been entered.
• When the image is blurred or noisy, switch to
the optimal mode.
• When using progressive inputs, inputs are directly displayed so that 2D Progressive, 3D
Progressive and Film Mode cannot be selected.
42
Note
• An international standard of color reproduction regulated by the IEC (International
Electrotechnical Commission). As the fixed
color area has been decided by the IEC, the
images are displayed in a natural tint based
on an original image, when “sRGB” is set to
“ON”.
• For additional information about the sRGB
function, visit “http://www.srgb.com/”.
• You cannot set the items, “Red”, “Blue”, “CLR
Temp”, “Bright Boost”, when “sRGB” is set to
“On”.
Info
• When “sRGB” is set to “On”, the projected
image may become dark, but this does not
indicate a malfunction.
Adjusting the Projected Image
(“SCR - ADJ” menu)
You can adjust the projected image and on-screen display to your preferences using the “SCR ADJ” menu.
Setting the Resize Mode
Adjusting the Image Position
You can move the projected image vertically.
Menu operation n Page 38
Picture
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
SEL./ADJ.
SCR - ADJ
Menu operation n Page 36
PRJ - ADJ
Help
0
0
Off
On
Logo
On
Front
English
ENTER
Picture
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
Normal
END
SEL./ADJ.
SCR - ADJ
PRJ - ADJ
Help
Stretch
0
0
Off
On
Logo
On
Front
English
ENTER
END
Note
• For details of the Resize mode, see pages 30
and 31.
• You can also press HRESIZE on the remote
control to set the resize mode. (See page 30.)
O button
Q button
Useful
Features
Note
• You cannot set this item when “Resize” is set
to “Normal”.
• To reset this function, select “0”.
• When adjusting the image shift, “Keystone” is
set to “0” and “Auto Keystone” is set to “Off”.
43
Adjusting the Projected Image (“SCR - ADJ” menu) (Continued)
Keystone Correction
Setting On-screen Display
When the image is projected either from the top
or from the bottom towards the screen at an
angle, the image becomes distorted
trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.
This function allows you to turn the on-screen
messages on or off.
Menu operation n Page 38
Picture
Auto Keystone Correction
Set “Auto Keystone” on the “SCR - ADJ”
menu to “On”.
Menu operation n Page 38
Manual Keystone Correction
Set “Auto Keystone” on the “SCR - ADJ”
menu to “Off”, and select “Keystone”,
then adjust with the slide bar.
Menu operation n Page 36
Picture
SCR - ADJ
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
SEL./ADJ.
PRJ - ADJ
Help
Normal
0
0
Off
On
Logo
On
Front
English
ENTER
END
Manual Correction
O button
Q button
Note
• The Keystone Correction can be adjusted up
to an angle of approximately ±13 degrees with
the “Auto Keystone” and up to an angle of
approximately ±15 degrees with the manual
“Keystone”.
(when “Resize” is set to “Normal”)
• When the screen is slanting or the image is
deteriorated, set “Auto Keystone” to “Off”.
• When adjusting the keystone or when “Auto
Keystone” is set to “On”, “Image Shift” is automatically set to “0”.
44
SCR - ADJ
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
SEL./ADJ.
PRJ - ADJ
Help
Normal
0
0
Off
On
Logo
On
Front
English
ENTER
END
Description of Items
Selectable
items
Description
On
All On-screen Displays are displayed.
Off
INPUT/VOLUME/AV MUTE/FREEZE/
AUTO SYNC/RESIZE/PICTURE MODE/
“An invalid button has been pressed.”
are not displayed.
Selecting the Background Image Setting the Setup Guide
You can set the Setup Guide screen during the
projector startup.
Menu operation n Page 38
Picture
SCR - ADJ
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
Menu operation n Page 38
PRJ - ADJ
Help
Picture
0
0
Off
On
Logo
On
Front
English
SEL./ADJ.
ENTER
Description of Items
Selectable items
SCR - ADJ
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
Normal
END
PRJ - ADJ
Help
Normal
0
0
Off
On
Logo
On
Front
English
SEL./ADJ.
ENTER
END
Description of Items
Description
Logo
Sharp logo screen
Blue
Blue screen
None
—
Selectable items
Description
On
Displaying the Setup Guide
when turning the projector on.
Off
Not displaying the Setup
Guide.
Useful
Features
45
Adjusting the Projected Image (“SCR - ADJ” menu) (Continued)
Reversing/Inverting Projected Selecting the On-screen Display
Images
Language
The projector can switch the on-screen display
language among 11 languages.
Menu operation n Page 38
Picture
SCR - ADJ
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
Menu operation n Page 38
PRJ - ADJ
Help
0
0
Off
On
Logo
On
Front
English
SEL./ADJ.
ENTER
END
Description of Items
Selectable items
46
Picture
SCR - ADJ
Resize
Image Shift
Keystone
Auto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
Language
Normal
SEL./ADJ.
Selectable items
Description
Front
Projecting from the front of the
screen
Front + Rotate
Projecting with a mirror
Rear
Projecting from the rear of the
screen or with a mirror
Rear + Rotate
Projecting with a mirror
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
PRJ - ADJ
Help
Normal
0
0
Off
On
Logo
On
Front
English
ENTER
END
Setting the Projector Function
(“PRJ - ADJ” menu)
You can use the “PRJ - ADJ” menu to enhance the usage for the projector.
Eco/Quiet Mode
Auto Search Function
Menu operation n Page 38
Picture
SCR - ADJ
PRJ - ADJ
Eco/Quiet Mode
Auto Search
Auto Power Off
Guide LEDs
System Sound
System Lock
Help
On
On
On
On
On
Lamp Timer(Life)
SEL./ADJ.
0 h
ENTER
Menu operation n Page 38
Picture
100%
END
Note
SCR - ADJ
Description of items
Fan
sound
Power
consumption
(When using
AC 100V)
Lamp Life
On
Approx.
90%
Low
177W
Approx.
4,000
hours
Off
100%
Standard
195W
Approx.
3,000
hours
PRJ - ADJ
Eco/Quiet Mode
Auto Search
Auto Power Off
Guide LEDs
System Sound
System Lock
Lamp Timer(Life)
• This function is factory preset to “Off”.
• When “Eco/Quiet Mode” is set to “On”, the
power consumption will decrease and the
lamp life will extend. (Projection brightness
decreases 10%.)
SelectBrightable
ness
items
This function automatically searches for and
switches to the input mode in which signals are
being received, when the projector is turned on,
or when the INPUT button is pressed.
SEL./ADJ.
Help
On
On
On
On
On
0 h
ENTER
100%
END
Note
ing INPUT (W/Y) on the projector.
Useful
Features
When “Auto Search” is set to “On”
• The projector automatically selects the available input source.
• If two or more input signals are found, the projector selects the input source in the order of
INPUT 1 n INPUT 2 n INPUT 3 when you
press INPUT (W/Y) on the projector.
• While “Auto Search” is set to “On”, press
CINPUT 1, DINPUT 2 or EINPUT 3 on
the remote control to select an input mode
other than the input mode selected by the projector.
• When “Auto Search” is set to “Off”, input mode
switches in order of
INPUT1 INPUT2 INPUT3
by press-
47
Setting the Projector Function (“PRJ - ADJ” menu) (Continued)
Auto Power Off Function
Setting the Guide LEDs
Menu operation n Page 38
Picture
SCR - ADJ
Menu operation n Page 38
PRJ - ADJ
Eco/Quiet Mode
Auto Search
Auto Power Off
Guide LEDs
System Sound
System Lock
Lamp Timer(Life)
SEL./ADJ.
Help
0 h
ENTER
100%
PRJ - ADJ
SEL./ADJ.
Help
On
On
On
On
On
0 h
ENTER
100%
END
Description of items
Description
On
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter standby mode.
Off
The Auto Power Off function will be
disabled.
Note
• When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
48
SCR - ADJ
Lamp Timer(Life)
END
Description of items
Selectable
items
Picture
Eco/Quiet Mode
Auto Search
Auto Power Off
Guide LEDs
System Sound
System Lock
On
On
On
On
On
Selectable
items
Description
On
The indicators for operation guidance
and the buttons for operation light up.
Off
No indicators or buttons for operation
guidance blinks or lights up.
System Lock Function
This function prevents unauthorized use of the
projector. Once this function is activated, users
must enter the correct keycode each time the
projector is turned on. We suggest you record
the keycode in a safe place where only authorized users have access.
2
Note
• You can not use the following buttons for
keycode:
•AON/STANDBY
•IENTER
•JRETURN
•BMENU/HELP
• System lock function recognizes each
button on the remote control or on the
projector as an individual button, even
if they share the same button name. If
you set the keycode with the buttons
on the projector, use only those buttons on the projector. If you set the
keycode with the buttons on the remote control, use only those buttons
on the remote control.
Info
• If you lose or forget your keycode, contact your
nearest Sharp Authorized Projector Dealer or
Service Center (see page 62). Even if the product warranty is valid, the keycode reset will
incur a charge.
Menu operation n Page 38
Picture
SCR - ADJ
Eco/Quiet Mode
Auto Search
Auto Power Off
Guide LEDs
System Sound
System Lock
PRJ - ADJ
Press the 4 buttons on the remote
control or on the projector to enter the new keycode in “New
code”.
Help
On
On
On
On
On
PRJ - ADJ
Setting the System Lock
Setting/Changing the keycode
1
Press the 4 buttons on the remote
control or on the projector to enter the preset keycode in “Old
Code”.
PRJ - ADJ
Setting the System Lock
Old Code
New Code
Reconfirm
– – – –
– – – –
– – – –
Note
• If you input a wrong keycode, the cursor
returns to the first point of the “Old Code”.
• The preset keycode is 4 Y buttons on
the projector. When this keycode is set,
the keycode input screen does not appear.
3
****
– – – –
– – – –
Enter the same keycode in “Reconfirm”.
Note
Not displaying the keycode input screen
when turning the projector on
• Press Y on the projector for four times in steps
2 and 3 above.
When the System Lock is set
Useful
Features
• When setting the keycode for the first
time, press Y on the projector for four
times.
Old Code
New Code
Reconfirm
• When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to
start projection.
Input screen for keycode
System Lock
– – – –
49
Setting the Projector Function (“PRJ - ADJ” menu) (Continued)
Setting the Confirmation Sound Checking the Lamp Life Status
You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
Menu operation n Page 38
Picture
SCR - ADJ
Menu operation n Page 36
PRJ - ADJ
Eco/Quiet Mode
Auto Search
Auto Power Off
Guide LEDs
System Sound
System Lock
Lamp Timer(Life)
SEL./ADJ.
Help
0 h
ENTER
100%
END
Description of items
Selectable
items
On
Off
Picture
SCR - ADJ
PRJ - ADJ
Eco/Quiet Mode
Auto Search
Auto Power Off
Guide LEDs
System Sound
System Lock
On
On
On
On
On
Help
On
On
On
On
On
Lamp Timer(Life)
SEL./ADJ.
0 h
ENTER
100%
END
Description of Lamp Life
Description
A confirmation sound is made when
the projector turns on/off.
No confirmation sound is made.
Lamp usage condition
“Life”
Remaining lamp life
100%
5%
Operated exclusively in
Eco/Quiet Mode “On”
Approx.
4,000
hours
Approx.
200 hours
Operated exclusively in
Eco/Quiet Mode “Off”
Approx.
3,000
hours
Approx.
150 hours
Note
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
For lamp replacement, contact your nearest
Sharp Authorized Projector Dealer or Service
Center.
• The lamp life may vary depending on the usage condition.
50
Troubleshooting with “Help” menu
This function advises you to solve the problems during usage.
MENU/HELP
button
Displaying “Help” menu screen
Adjuatment button
(P/R/O/Q)
ENTER button
Example: When image flickering appears
Operation to solve image flickering when projecting the computer RGB signal.
1
Press BMENU/HELP.
4
Select “Initiate “Auto Sync” Adjustments”, then press IENTER.
2
Press O or Q to select “Help”, then
press IENTER.
5
If the image is not improved, select “Adjust horizontal noise.”,
then press IENTER.
6
Press O or Q to adjust.
Picture
SCR - ADJ
PRJ - ADJ
Help
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
Help
Phase
SEL./ADJ.
0
Rtn. Menu
END
Reset all adjustments to default settings
SEL.
3
ENTER
END
Help
Vertical stripes or flickering image appear
Initiate "Auto Sync" Adjustments.
If there is no change after performing "Auto Sync"
adjustments, adjust the following items.
Useful
Features
Press P or R to select “Vertical
stripes or flickering image appears” on Help menu, then press
IENTER.
Note
• You can adjust the items with check marks (✔).
• Some items in the Help menu may not appear,
depending on the projected image.
• If the problem is not solved, refer to
“Troubleshooting”. (see pages 60 and 61)
Adjust vertical noise
Adjust horizontal noise
Reset the 2 items above
Return
Cur. sig. freq: H 43 kHz / V 60 Hz
SEL.
ENTER
END
51
Maintenance
Cleaning the projector
■ Be sure to unplug the power cord before
cleaning the projector.
■ The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or
thinner, as these can damage the finish on the
cabinet.
■ Do not use volatile agents such as insecticides
on the projector.
Do not attach rubber or plastic items to the
projector for long periods.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the
projector.
Cleaning the lens
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera lenses)
for cleaning the lens. Do not use any liquid type
cleaning agents, as they may wear off the
coating film on the surface of the lens.
■ As the surface of the lens can easily get
damaged, be sure not to scrape or hit the lens.
rge
ete
dd
Mil
nt
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Mild detergent diluted
with water
Wax
Thinner
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth in
a mild detergent diluted with water, wring the
cloth well and then wipe the projector.
Strong cleaning detergents may discolor, warp
or damage the coating on the projector. Make
sure to test on a small, inconspicuous area on
the projector before use.
52
Maintenance Indicators
■ The warning lights (ON/STANDBY button, lamp indicator and temperature warning indicator) on
the projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate
red, and the projector will enter standby mode. After the projector has entered standby mode,
follow the procedures given below.
ON/STANDBY button
Lamp indicator
Temperature warning indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
“
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp
will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec” appears, be sure to perform the measures described on page
tor will enter standby mode. After “
54.
About the lamp indicator
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be
displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will
automatically turn off and then the projector will automatically enter standby mode. At this time, the
lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will
not turn on.
Appendix
53
Maintenance Indicators (Continued)
Maintenance indicator
Temperature
warning
indicator
Lamp
indicator
Power
button
Normal
Abnormal
Off
Red on
(Standby)
Green on
(Green
blinks
when the
lamp is
warming
up.)
Green on/
Red on
Problem
The internal
temperature is
abnormally
high.
Cause
Possible Solution
• Blocked air intake
• Relocate the projector to
an area with proper
ventilation. (see page 8)
• Cooling fan
breakdown
• Internal circuit
failure
• Clogged air intake
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 62) for
repair.
The lamp does
not illuminate.
• The lamp is shut
down abnormally.
• Disconnect the power cord
from the AC outlet, and
then connect it again.
Time to change
the lamp.
• Remaining lamp life
becomes 5% or
less.
Red on
(Standby)
The lamp does
not illuminate.
• Burnt-out lamp
• Lamp circuit failure
• Carefully replace the lamp.
(See page 56.)
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 62) for
repair.
• Please exercise care when
replacing the lamp.
• Securely install the cover.
Red
blinks
The power
indicator blinks
in red when the
projector is on.
• The lamp unit cover
is open.
Red on
• If the power indicator blinks
in red even when the lamp
unit cover is securel
installed, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 62) for
advice.
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,
replace the power cord in the AC outlet and then turn the power on again.
• If you want to clean the air vents during projector operation, be sure to press SON/STANDBY on
the projector or AON/STANDBY on the remote control and put the projector into standby mode.
After the cooling fan has stopped, clean the vents.
• The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
• Do not unplug the power cord after the projector has entered standby mode and while the cooling
fan is running. The cooling fan runs for about 90 seconds.
54
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display. (see page 50)
■ Purchase a replacement lamp of type AN-XR1LP from your place of purchase, nearest Sharp Projector
Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited
warranty. All service of this projector under warranty, including lamp replacement,
must be obtained through a Sharp Authorized Projector Dealer or Service Center.
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal
Information
U.S.A. ONLY
www.lamprecycle.org or 1-800-BE-SHARP
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case
of exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burn or injury.
■ Carefully change the lamp by following the instructions described in this section. * If you wish,
you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service
Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
Appendix
55
Regarding the Lamp (Continued)
Removing and Installing the
Lamp Unit
Info
• Be sure to remove the lamp unit using the
handle. Be sure not to touch the glass surface
of the lamp unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, be sure to carefully follow the steps
below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
1
Lamp unit
AN-XR1LP
Optional
accessory
Press SON/STANDBY on the projector or AON/STANDBY on the
remote control to put the projector
into standby mode.
• Wait until the cooling fan stops.
ON/STANDBY button
Warning!
• Do not remove the lamp unit from the
projector right after use. The lamp and
parts around the lamp will be very hot
and may cause burns or injury.
2
3
Disconnect the power cord.
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
AC socket
Remove the lamp unit cover.
• Turn the projector over. Loosen the user
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover
(2).
User service screw
(for lamp unit cover)
56
4
Remove the lamp unit.
5
Insert the new lamp unit.
6
Handle
• Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp
unithorizontal and do not tilt it.
• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
Securing screws
Replace the lamp unit cover.
• Align the tab on the lamp unit cover
(1)and place it while pressing the tab
(2) to close it. Then tighten the user service screw (3) to secure the lamp unit
cover.
Info
• If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is connected to the projector.
User service
screw (for
lamp unit
cover)
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or explode.
1
Connect the power cord.
2
Reset the lamp timer.
AC socket
ON/STANDBY button
ENTER button
• Plug the power cord into the AC socket
of the projector.
Y button
Appendix
• While simultaneously holding down
UMENU, TENTER and Y on the projector, press and SON/STANDBY on the
projector.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
MENU button
57
Connecting Pin Assignments
INPUT 1 RGB Signal Terminal: 15-pin Mini D-sub female connector
11
15
1
6
5
10
RGB Input
Component Input
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Video input (red)
Video input (green/sync on green)
Video input (blue)
Not connected
Not connected
Earth (red)
Earth (green/sync on green)
Earth (blue)
Not connected
GND
Not connected
Bi-directional data
Horizontal sync signal: TTL level
Vertical sync signal: TTL level
Data clock
USB Terminal: 4-pin B-type USB female connector
1 2
3 4
58
1.
2.
3.
4.
Signal
Signal name
SG
USB+
VCC
USB–
GND
USB data+
USB power
USB data–
PR (CR)
Y
PB (CB)
Not connected
Not connected
Earth (PR)
Earth (Y)
Earth (PB)
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Computer Compatibility Chart
Computer
• Multiple signal support
• Compatible with the signals below in
Horizontal Frequency: 15-70 kHz,
intelligent compression
Vertical Frequency: 45-85 Hz,
XR-1X: SXGA, SXGA+
Pixel Clock: 12-108 MHz
XR-1S: XGA, SXGA, SXGA+
Sync signal:Compatible with TTL level
• Intelligent Compression and Expansion
• Compatible with sync on green signal
System resizing technology
The following is a list of modes that conform to VESA. However, this projector supports other
signals that are not VESA standards.
Resolution
PC/MAC
640 × 350
640 × 400
720 × 350
VGA
720 × 400
640 × 480
PC
MAC 13"
MAC 16"
MAC 19"
MAC 21"
SVGA
800 × 600
XGA
1,024 × 768
SXGA
1,152 × 864
1,280 × 1,024
SXGA+ 1,400 × 1,050
640 × 480
VGA
800 × 600
SVGA
832 × 624
1,024 × 768
XGA
SXGA 1,152 × 870
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.1
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
55.0
66.2
67.5
64.0
64.0
34.9
37.8
49.7
60.2
68.7
60
70
85
60
70
85
60
70
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
70
75
60
60
67
60
75
75
75
VESA Standard
Display
XR-1X
XR-1S
✔
✔
Upscale
✔
✔
Upscale
✔
✔
✔
✔
✔
True
✔
✔
✔
✔
✔
✔
✔
True
✔
✔
Intelligent
Compression
Intelligent
Compression
Upscale
True
Intelligent Compression
Upscale
True
Intelligent
Compression
Note
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this
occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to
change display modes can be found in your notebook computer’s operation manual.
• When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.
DTV
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
480I
15.7
60
480P
31.5
60
540P
33.8
60
576I
15.6
50
576P
31.3
50
720P
45.0
60
1035I
28.1
50
1035I
33.8
60
1080I
28.1
50
1080I
33.8
60
Appendix
Signal
59
Troubleshooting
Problem
Check
Page
• Projector power cord is not plugged into the wall outlet.
25
• Power to the external connected devices is off.
–
• The selected input mode is wrong.
29
• Cables incorrectly connected to the projector.
23, 24, 25
• Remote control battery has run out.
14, 15
No picture and no sound • External output has not been set when connecting notebook
computer.
or projector does not
start.
• The lamp unit cover is not installed correctly.
23
56, 57
• Cables incorrectly connected to the projector.
23, 24, 25
• “Bright” is set to minimum position.
40
• Image adjustments are incorrectly set.
40
Sound is heard but no
picture appears (or picture
is dark).
(Video Input only)
• Video input system is incorrectly set.
51
• Adjust the focus.
27
• The projection distance exceeds the focus range.
19
Color is faded or poor.
(Computer Input only)
Picture is blurred;
noise appears.
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
51
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
51
• Noise may appear depending on the computer.
–
• Cables incorrectly connected to the projector.
23, 24, 25
• Volume is set to minimum.
29
Picture appears but no
sound is heard.
• If the picture is normal, the sound is due to cabinet shrinkage
An unusual sound is
caused by room temperature changes. This will not affect operation
occasionally heard from
or performance.
the cabinet.
Maintenance indicator on • See “Maintenance Indicators”.
the projector illuminates
or blinks in red.
60
–
54
Problem
Picture is green on
INPUT 1 COMPONENT.
Check
• Change the input signal type setting.
51
Picture is pink (no green)
on INPUT 1 RGB.
Picture is too bright and
whitish.
• Image adjustments are incorrectly set.
The cooling fan becomes • When temperature inside the projector increases, the cooling fan
runs faster.
noisy.
The lamp does not light
up even after the
projector turns on.
Page
40
–
• The lamp indicator is illuminating in red.
Replace the lamp.
53
The lamp suddenly turns
off during projection
The image sometimes
flickers.
• Cables incorrectly connected to the projector or the connected
equipment works improperly.
• If this happens frequently, replace the lamp.
The lamp needs much
time to turn on.
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
23, 24,
25, 51, 56
56
Picture is dark.
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 30 seconds.
Appendix
61
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first
refer to the “Troubleshooting” section on pages 60 and 61. If this operation manual
does not answer your question, please contact the SHARP Service departments
listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
http://www.sharp.nl
http://www.sharp.be
http://www.sharp.lu
Australia
Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
http://www.sharp.net.au
New Zealand
Sharp Corporation of New Zealand
(09) 634-2059, (09) 636-6972
http://www.sharpnz.co.nz
Singapore
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
ckng@srs.global.sharp.co.jp
http://www.sharp.com.sg
Hong Kong
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
dcmktg@srh.global.sharp.co.jp
http://www.sharp.com.hk
Taiwan
Sharp Corporation (Taiwan)
0800-025111
http://www.sharp-scot.com.tw
Malaysia
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
lcdsupport@sharpsec.com
http://www.sharplcd.com
Canada
Sharp Electronics of Canada Ltd.
(905) 568-7140
http://www.sharp.ca
Mexico
Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin
American Group
(305) 264-2277
www.servicio@sharpsec.com
http://www.siempresharp.com
Germany
Sharp Electronics (Europe) GMBH
01805-234675
http://www.sharp.de
U.K.
Sharp Electronics (U.K.) Ltd.
0161-205-2333
cic@sharp-uk.co.uk
http://www.sharp.co.uk
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
http://www.sharp.it
U.A.E.
France
Sharp Electronics France
01 49 90 35 40
hotlineced@sef.sharp-eu.com
http://www.sharp.fr
Sharp Middle East Fze
971-4-81-5311
helpdesk@smef.global.sharp.co.jp
Thailand
Spain
Sharp Electronica Espana, S.A.
93 5819700
sharplcd@sees.sharp-eu.com
http://www.sharp.es
Sharp Thebnakorn Co. Ltd.
02-236-0170
svc@stcl.global.sharp.co.jp
http://www.sharp-th.com
Korea
Switzerland
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
cattaneo@sez.sharp-eu.com
http://www.sharp.ch
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
lcd@sharp-korea.co.kr
http://www.sharpkorea.co.kr
India
Sweden
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
vision.support@sen.sharp-eu.com
http://www.sharp.se
Sharp Business Systems (India)
Limited
(91) 11- 6431313
service@sharp-oa.com
Austria
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
pogats@sea.sharp-eu.com
http://www.sharp.at
62
Specifications
As a part of policy of continuous improvement, SHARP reserves the right to make
design and specification changes for product improvement without prior notice.
The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
63
Appendix
Product type Projector
Model XR-1X / XR-1S
Video system NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/
DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50
Display method Single Chip Digital Micromirror DeviceTM (DMDTM) by Texas Instruments
DMD panel Panel size: [XR-1X] 0.7" (17.5 mm) (10.5 [H] × 14.0 [W] mm), 1 chip XGA DMD
[XR-1S] 0.55" (13.7 mm) (8.2 [H] × 10.9 [W] mm), 1 chip SVGA DMD
No. of dots: [XR-1X] 786,432 dots (1,024 [H] × 768 [V])
[XR-1S] 480,000 dots (800 [H] × 600 [V])
Lens [XR-1X] 1–1.16 × zoom lens, F2.80–3.10, f = 25.8–30.0 mm
[XR-1S] 1–1.16 × zoom lens, F2.60–2.84, f = 19.3–22.6 mm
Projection lamp 150 W DC lamp
Component input signal 15-pin mini D-sub connector
(INPUT1) Y: 1.0 Vp-p, sync negative, 75 Ω terminated
PB: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
Horizontal resolution [XR-1X] 700 TV lines (DTV720P)
[XR-1S] 520 TV lines (DTV720P)
Computer RGB input 15-pin mini D-sub connector
signal (INPUT 1) RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
S-video input signal 4-pin mini DIN connector
(INPUT 2) Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
Video input signal RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω
(INPUT 3) terminated
Pixel clock 12–108 MHz
Vertical frequency 45–85 Hz
Horizontal frequency 15–70 kHz
Audio input signal ø3.5 mm minijack: AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)
Speaker system 2.8 cm round × 1
Rated voltage AC 100–240 V
Input current 2.0 A
Rated frequency 50/60 Hz
Power consumption 195 W (Standard mode)/177 W (Eco/Quiet mode “On”) with AC 100 V
190 W (Standard mode)/167 W (Eco/Quiet mode “On”) with AC 240 V
Power consumption (standby) 4 W (AC 100 V) – 5 W (AC 240 V)
Heat dissipation 730 BTU/hour (Standard mode)/660 BTU/hour (Eco/Quiet mode “On”) with AC 100 V
710 BTU/hour (Standard mode)/630 BTU/hour (Eco/Quiet mode “On”) with AC 240 V
Operating temperature 41°F to 95°F (+5°C to +35°C)
Storage temperature –4°F to 140°F (–20°C to +60°C)
Cabinet Plastic
I/R carrier frequency 38 kHz
Dimensions (approx.) 9 47/64" × 2 17/32" × 4 13/16" (247 (W) × 64 (H) × 122 (D) mm) (main body only)
9 47/64" × 2 23/32" × 4 13/16" (247 (W) × 69 (H) × 122 (D) mm) (including adjustment
foot and projecting parts)
Weight (approx.) 3.20 lbs. (1.45 kg)
Supplied accessories Remote control, Lithium battery, Power cord for U.S., Canada etc. (6', 1.8 m),
Power cord for Europe, except U.K. (6', 1.8 m), Power cord for U.K., Hong Kong
and Singapore (6', 1.8 m), Power cord for Australia, New Zealand and Oceania
(6', 1.8 m), RGB/USB cable (6', 1.8 m), Cable tie × 2, Soft case, Projector
manual CD-ROM, Operation manual
Replacement parts Lamp unit (Lamp/cage module) (AN-XR1LP), Remote control
(RRMCGA256WJSA), Lithium battery, Power cord for U.S., Canada etc.
(QACCDA029WJPZ), Power cord for Europe, except U.K. (QACCVA006WJPZ),
Power cord for U.K., Hong Kong and Singapore (QACCBA015WJPZ), Power
cord for Australia, New Zealand and Oceania (QACCLA024WJPZ), RGB/USB
cable (QCNWGA047WJPZ), Cable tie (UBNDTA015WJZZ), Soft case
(GCASNA011WJZZ), Projector manual CD-ROM (UDSKAA045WJN1), Operation manual (TINS-B148WJN1)
Dimensions
Units: inches (mm)
4 13/16 (122)
9 47/64 (247)
2 17/32 (64)
1 19/32 (40.3) 1 9/64 (28.7)
XR-1X
2 7/32 (56)
6 11/32 (161)
1 15/16 (49)
7 5/64 (179.5)
2 43/64 (67.5)
2 17/32 (64)
1 27/64 (36) 1 5/16 (33)
XR-1S
2 7/32 (56)
6 11/32 (161)
7 5/64 (179.5)
1 15/16 (49)
2 43/64 (67.5)
3 59/64 (99.3)
4 1/2 (114.3)
19
/32 (15)
4 47/64 (120)
8 9/32 (210)
64
/ (18.5)
47 64
Index
AC socket .................................................. 25
Accessories .............................................. 11
Adjustment buttons ................................... 36
Adjust vertical noise ........................... 35, 51
Aspect ratio ............................................... 30
AUDIO INPUT terminal ................. 23, 24, 25
Auto Keystone Correction ........................ 44
Auto Power Off ......................................... 48
Auto Search .............................................. 47
Auto Sync
(Auto Sync adjustment) .............. 32, 35, 51
AUTO SYNC button .................................. 32
AV MUTE button ....................................... 29
Background ............................................... 45
Blue ........................................................... 40
BORDER ............................................. 30, 31
Bright ......................................................... 40
Bright Boost .............................................. 41
Clock ......................................................... 51
CLR Temp (Color Temperature) ............... 41
Color ......................................................... 40
Contrast .................................................... 40
Eco/Quiet Mode ........................................ 47
ENTER button ........................................... 36
Exhaust vent ............................................. 13
Fine Sync .................................................. 51
Focus ring ................................................. 27
FREEZE button ........................................ 32
Front adjustment foot ............................... 28
Guide LEDs .............................................. 48
H-Pos .................................................. 35, 51
HEIGHT ADJUST button .......................... 28
Help ........................................................... 51
Image shift ................................................ 43
INPUT 1 terminal ................................ 23, 24
INPUT 1 – 3 modes .................................. 29
INPUT 2 terminal ...................................... 24
INPUT 3 terminal ...................................... 25
INPUT button ............................................ 29
Intake vent .......................................... 13, 52
Lamp Timer (Life) ..................................... 50
Lamp unit .................................................. 56
Language
(on-screen display language) ................. 46
Lithium Battery .................................... 14, 15
MENU/HELP button ............................ 36, 51
MOUSE/Adjustment buttons .................... 33
Mouse function ......................................... 33
NORMAL ............................................. 30, 31
ON/STANDBY button ............................... 26
Optional accessories ................................ 11
OSD Display ............................................. 44
PDF ........................................................... 10
Phase ........................................................ 51
Picture Adjustment .................................... 40
Picture Mode ............................................. 40
Power cord ................................................ 25
PRJ - ADJ ................................................. 47
PRJ Mode ................................................. 46
Progressive ............................................... 42
R CLICK/RETURN button ........................ 33
Rear adjustment foot ................................ 28
Red ........................................................... 40
Remote control ......................................... 14
Remote control sensor ............................. 15
Replacing the lamp ................................... 55
Resize ....................................................... 43
RESIZE button .......................................... 30
RETURN button ........................................ 37
RGB/USB cable ........................................ 23
SCR - ADJ ................................................ 43
Screen Size and Projection Distance (XR-1S) ... 20
Screen Size and Projection Distance (XR-1X) ... 19
Setup Guide .............................................. 27
Sharp ........................................................ 40
Soft case ................................................... 11
sRGB ........................................................ 42
STRETCH ........................................... 30, 31
Supplied accessories ............................... 11
System Lock ............................................. 49
Temperature warning indicator ................. 53
Tint ............................................................ 40
L CLICK/ENTER button ............................ 33
Lamp ......................................................... 55
Lamp indicator .......................................... 53
Video System ............................................ 35
Volume buttons ......................................... 29
V-Pos .................................................. 35, 51
USB terminal ............................................. 23
Zoom knob ................................................ 28
65
Appendix
Kensington Security
Standard connector ................................ 13
Keycode .................................................... 49
Keystone Correction ................................. 44
SHARP CORPORATION