Miele CS 1112 E Operating instructions

Installation Instructions
CS1112 E
CS1122 E
en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
IMPORTANT SAFETY INSTRUCTIONS
Children
WARNING- When using your
appliance follow basic
precautions, including the
following:
Read all instructions before
installation or use to prevent
injury and appliance damage.
This appliance conforms to all
uniform safety codes and
regulations. The manufacturer
cannot be held responsible for
damage or injury caused by
improper use of this appliance.
Keep these operating instructions
in a safe place and pass them on
to any future user.
SAVE THESE INSTRUCTIONS
Correct usage
~ Children should not be left
unattended in an area where the
appliance is in use. Never allow
children to sit or stand on any part of
the appliance.
Caution: Do not store items of interest
to children in cabinets above the
appliance. Children climbing on the
appliance to reach these items could
be injured.
~ The appliance is hot during use and
remains so for some time after being
switched off. Keep children away from
the appliance.
~ Ensure that any packing material, is
disposed of safely and kept out of the
reach of children. Danger of
suffocation!
~ Keep all pots and pans out of the
reach of children. Danger of burning or
scalding.
~ Only use the cooktop for residential
cooking, and for the purposes
described in this manual.
Other uses are not permitted and can
be dangerous. The manufacturer will
not be held liable for damage caused
by unauthorized use or improper
operation of any kind.
~ Persons who lack physical, sensory
or mental abilities, or experience with
the appliance should not use it without
supervision or instruction by a
responsible person.
3
IMPORTANT SAFETY INSTRUCTIONS
Technical safety
~ Installation, repair and maintenance
work should be performed by a Miele
authorized service technician. Work by
unqualified persons could be
dangerous and may void the warranty.
~ Before installing the cooktop, check
for externally visible damage. Do not
operate a damaged appliance.
~ To guarantee the electrical safety of
this appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician. The manufacturer
will not be held responsible for
damages caused by the lack, or
inadequacy, of an effective grounding
system.
~ Before installation, make sure that
the voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond to prevent injury and
appliance damage. Consult a qualified
electrician if in doubt.
~ Do not use an extension cord to
connect this appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance.
~ Do not use the appliance until it has
been properly installed in the
countertop.
4
~ Install the appliance so that the
power cord does not come into contact
with any portion of the cooktop which
may become hot during use.
~ Before servicing, disconnect the
appliance from the main power supply.
~ Do not operate any appliance with a
damaged cord or plug, or if the
appliance has been damaged in any
manner. Contact Miele’s Technical Service Department.
~ Under no circumstances open the
outer casing of the appliance.
~ While the appliance is under
warranty repairs should only be
performed by an authorized service
technician. Otherwise the warranty is
void.
~ In the event of any damage to the
appliance, it must be turned off immediately and disconnected from the main
power supply. Contact Miele’s
Technical Service Department.
Do not use the appliance until it has
been repaired. Ensure power is not
supplied to the appliance until repair
work is completed.
~ Defective components should be
replaced by Miele original spare parts
only. Only with these parts can the
manufacturer guarantee the safety of
the appliance.
IMPORTANT SAFETY INSTRUCTIONS
~ Do not cook on a broken cooktop.
Any breakages or cracks in the ceramic
surface of the appliance are defects
and must be treated as such. If the
cooktop should break, cleaning
solutions and spills may penetrate the
broken cooktop and create a risk of
electric shock. Do not use the
appliance until it has been repaired.
Safety
~ The appliance is hot during use and
remains so for some time after being
switched off. Be careful not to touch the
appliance if it may still be hot.
~ Protect your hands with oven mitts
or potholders when using the
appliance. Use only dry, heat resistant
potholders. Moist or damp potholders
used on hot surfaces can result in
steam burns. Do not let the potholder
touch the hot heating elements. Do not
use towels or other bulky items near the
appliance.
~ Do not store items on the appliance
when not in use. Items could melt or
catch fire from residual heat or if the
appliance is turned on inadvertently.
Always switch the cooking zone(s) off
after use.
~ Never cover the appliance with a
cloth. A fire may result.
~ Be aware of loose fitting or hanging
garments when operating the
appliance, they may present a fire
hazard.
~ Never leave an appliance
unattended at high settings or when
cooking with oil or fat. Overheated oil
could ignite. Always heat oil slowly,
monitoring it as it heats.
~ Do not use water on grease fires.
Smother or use a dry chemical or
foam-type extinguisher on any fire or
flame.
~ Make certain that the power cords of
~ Do not heat unopened containers.
Built-up pressure may cause the
container to burst and result in injury.
small appliances do not come in
contact with the appliance. The
insulation of the cable could become
damaged. Danger of electric shock!
~ Do not flambé under an exhaust
~ Be careful not to drop anything on
hood. Flames could be drawn up into
the hood by the suction and the grease
filters may ignite.
the ceramic surface of the cooktop.
Even lightweight objects may cause
damage.
~ Never use the appliance to heat a
room. Due to the high temperatures
radiated, objects left near the appliance
could catch fire.
5
IMPORTANT SAFETY INSTRUCTIONS
~ Use the proper pan size. Select
cookware with flat bottoms large
enough to cover the heating element.
Using undersized cookware will expose
a portion of the heating element and
may result in ignition of clothing or
handles becoming hot. The proper size
pot or pan will also improve efficiency.
~ Pot and pan handles should be
turned inward and not extend over the
countertop to reduce the risk of burns,
ignition of flammable materials, and
spills.
~ Do not use pots or pans with
pronounced edges or ridges on the
ceramic cooktop. These could scratch
the cooktop permanently. See
"Selecting cookware" for more
information. Grains of salt and sand can
cause scratches. Make sure that the
bases of any pots and pans are clean,
free of any fat or oils and are dry.
~ To prevent damage to the cooktop
do not use pots and pans with thin
bases on the cooktop. Never heat an
empty pan unless the pan manufacturer
states that you can do so.
~ Before using glass, glass/ceramic,
ceramic, earthenware or other glazed
cookware verify that they can be used
on a cooking surface.
~ To prevent damage to the cooktop
do not use pots and pans with thin
bases on the cooktop. Never heat an
empty pan unless the pan manufacturer
states that you can do so.
6
~ To prevent burns and breathing
difficulty, allow the cooktop to cool
before cleaning. Some cleaners may
produce toxic fumes if applied to a hot
surface.
~ Keep the cooktop clean. Salt, sugar,
and grit can cause scratches.
~ When wiping spills on a hot cooktop
with a wet sponge or cloth, be careful
to avoid steam burns.
~ Do not let flammable materials,
i.e. cooking grease, accumulate on the
appliance.
~ Do not use a steam cleaner to clean
this appliance. Steam could penetrate
electrical components and cause a
short circuit.
~ Do not allow either solid or liquid
sugar, pieces of plastic or foil to fall on
the burners when they are hot. If these
residues are allowed to cool on the
ceramic surface pitting or even
cracking may occur.
~ Any spills should be removed as
quickly as possible to prevent them
from burning on and becoming difficult
to remove.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these
Important Safety instructions.
SAVE THESE INSTRUCTIONS
AND REVIEW THEM
PERIODICALLY
SAFETY INSTRUCTIONS FOR INSTALLATION
Note to the installer:
Please leave this instruction book
with the consumer for the local
electrical inspector’s use.
The minimum distances given in
these Installation Instructions must
be observed in order to ensure safe
operation. Failure to do so increases
the risk of fire.
The cabinetry and venting hood
should be installed first to prevent
damage to the cooktop.
~ The countertop must be bonded
with heat resistant (212 °F/100 °C)
adhesive to prevent distortion or
dissolving.
~ The cooktop must not be installed
over a dishwasher, washer, dryer,
refrigerator or freezer. Heat radiated by
the cooktop may damage them.
~ To eliminate the risk of burns or fire
by reaching over heated surfaces
cabinet storage space above the
appliance should be avoided. If cabinet
storage is necessary, the risk can be
reduced by installing a venting hood to
project horizontally a minimum of 5"
(127 mm) beyond the bottom of the
cabinets.
22
~ This appliance has not been
designed for maritime use or for use in
mobile installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
installation in these applications. Please
contact the Miele Technical Service
Department with specific requirements.
~ Do not install this appliance above
an oven unless the countertop is at
least 1 9/16" (40 mm) thick.
~ You must ensure the power cable
for the appliance will not come into
contact with the floor panel after
installation, nor be subject to any
mechanical strain.
~ The appliance must not be
permanently sealed into the countertop
when installed. The sealing strip under
the edge of the appliance provides a
sufficient seal for the countertop. See
"Sealing".
Keep this instruction book in a safe
place for reference and pass it on to
any future user.
SAFETY INSTRUCTIONS FOR INSTALLATION
Safety distances above the
appliance
If there is more than one appliance
beneath a hood (e.g. wok burner
and electric cooktop), and they have
different minimum safety distances
always observe the greater
distance.
The minimum safety distance given by
the hood manufacturer must be
maintained between the cooktop and
the hood above it. See the installation
instructions of the hood for these safety
measurements.
If the hood manufacturers instructions
are not available or if flammable objects
are installed over the cooktop (e.g.
cabinets, utensil rail, etc.), a minimum
safety distance of 30" (760 mm) must
be maintained.
23
SAFETY INSTRUCTIONS FOR INSTALLATION
Safety distances to the sides
of the appliance
The appliance should only be installed
as shown in the illustrations, while
maintaining the required safety
distances shown. Do not install the
appliance between two tall cabinets,
this is a fire hazard.
A distance of alteast 2" (50 mm) must
be kept between the countertop cut-out
and the rear wall because of the high
temperatures radiated.
2 " (50 mm)
recommended
The minimum distance a between the
worktop cut-out and a wall or tall unit to
the right or left of it is:
2" (50 mm)
for CS 1112
CS 1122
CS 1212
CS 1221
CS 1223
CS 1326
CS 1411
for
CS 1312
CS 1322
CS 1421
10" (250 mm) for
CS 1011
CS 1012
CS 1028
6" (150 mm)
2"
(50mm)
1
not recommended
not allowed
24
Installation
Safety distance when installing the appliance near a wall with trim or a back
splash
A minimum distance of 2" (50 mm) between the trim or back splash and the
countertop cut-out if required.
This distance is only necessary if these items are made of combustible materials
e.g. wood. If the trim or back splash is made of a non-combustible material, the
required safety distance can be reduced by the thickness of the wall covering
material.
a Wall frame
b Sheet rock or wall board
c Trim or back splash
d Countertop
e Countertop cut-out
f 2" (50 mm) minimum clearance
25
Installation
Installation dimensions
CS 1112
a Spring clips
b Appliance front
c Installation height
d Power supply box with connection cable, L = 78 3/4" (2000 mm)
26
Installation
CS 1122
a Spring clips
b Appliance front
c Installation height
d Power supply box with connection cable, L = 78 3/4" (2000 mm)
27
Installation
Cut out
^ Make the worktop cut-out for one or
more appliances as applicable.
Remember to maintain a minimum
safety distance from the back wall,
as well as from any tall unit or side
wall to the right or left of the
appliance(s).
See also "SAFETY INSTRUCTIONS
FOR INSTALLATION".
^ Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture.
The materials used must be heat
resistant.
28
If during installation the seal around
the frame does not sit flush with the
countertop in the corners, the corner
radius, maximum 3/16" (4 mm), can
be carefully filed down to fit.
Installation
Installation of multiple
appliances
When installing more than one combiset appliance, a support bar b must be
installed between the appliances.
Countertop cut-out
two appliances
D
Countertop cut-out
three appliances
(5 19 11
00 +
/1
6"
-1
m
m
b
)
D
(5
-1
b
C
A
For the installation of two appliances
the width of the countertop cut-out D is
the sum of A and C.
A, B and C = appliance widths
11 5/16", 15" or 22 11/16"
(288 mm, 380 mm or 576 mm)
minus 5/16" (8 mm) to allow for the
overhang
1
1
00 9 1/1
+
B
m
6"
m
)
C
A
For the installation of three appliances
the width of the countertop cut-out D is
the sum of A and B and C.
If more than three appliances are
being installed, you will need to add,
A, B or C for each additional
appliance.
D = width of the countertop cut-out
29
Installation
Sample calculations for a countertop cut-out for three appliances
30
A
appliance width
minus 5/16" (8 mm)
B
appliance width
C
appliance width
minus 5/16" (8 mm)
D
Countertop
cut-out
11"
(280 mm)
11 5/16"
(288 mm)
11"
(280 mm)
33 3/8"
(848 mm)
11"
(280 mm)
15"
(380 mm)
14 5/8"
(372 mm)
40 5/8"
(1032 mm)
11"
(280 mm)
22 11/16"
(576 mm)
22 3/8"
(568 mm)
56 1/16"
(1424 mm)
14 5/8"
(372 mm)
11 5/16"
(288 mm)
11"
(280 mm)
37"
(940 mm)
14 5/8"
(372 mm)
15"
(380 mm)
14 5/8"
(372 mm)
44 1/4"
(1124 mm)
14 5/8"
(372 mm)
22 11/16"
(576 mm)
22 3/8'
(568 mm)
59 11/16"
(1516 mm)
22 3/8"
(568 mm)
11 5/16"
(288 mm)
11"
(280 mm)
44 3/4"
(1136 mm)
22 3/8"
(568 mm)
15"
(380 mm)
14 5/8"
(372 mm)
52"
(1320 mm)
22 3/8"
(568 mm)
-
22 3/8"
(568 mm)
44 3/4"
(1136 mm)
Installation
"
3/16
1"5--130mm)
(2
D
2"
m) 0m
(5
(50m
"
2"m) 2"m)
3/16
m (50m
1"-130mm) (50
(25-
2"m)
a
a
a
b
c
(5 19 1
00 1/1
+
6"
-1
m
m
)
c a
a
a
B
C
3/8"
5/8"/ 22mm)
8
4
1"/1 72/56
1 (280/3
/16"
3/8"
211 )
2
/
"
5/8" / 22m)
6" 15
mm
/ 14 68m 11 5/1 8//380/576
11"280/372/5
8
2
(
(
A
a Spring clips
b Support bars
c Space between support bar and countertop
An additional support bar is required for each additional appliance. The position
for attachment of an additional spacing strip depends on the width of the
appliance B.
31
Installation
Attach the spring clips and
support bars
Wood or solid surface countertops
Granite countertop
"
"
1"-1
3/16
1"-1
mm)
(25-3
)
0mm
0
(25-3
a
b
^ Place the supplied spring clips a
and the support bars b at the
marked positions as shown above,
by laying them on the upper edge of
the cut-out and then securing them
with the 1/8" x 1" (3.5 x 25 mm) screws
(supplied).
32
3/16
c
a
c
b
^ Position and attach the spring clips
a and support bars b with strong,
double-sided tape c.
The screws are not needed for granite
countertops.
Installation
a
^ Coat the edges of the spring clips a,
d
b
^ and the space d between the
strips b and the countertop with
silicone (supplied).
33
Installation
Installing the appliance
^ Feed the power cord down through
the cut-out.
^ Then place the front side of the
appliance in the countertop cut-out.
^ Then with a hand on each side of the
appliance press down evenly on the
edges until it clicks into position.
When doing so make sure that the
appliance seal sits tightly on the
countertop to ensure it is sealed
correctly. Do not permanently seal
into the countertop.
^ Connect the appliance to the main
power supply.
^ Turn the appliance on and check the
function.
The appliance can be lifted out
using a special tool.
The appliance can also be pushed
up and out from underneath. Note
that the rear will need to be pushed
out first.
34
Installation
Sealing
Tiled surfaces
The appliance must not be permanently
sealed into the countertop when
installed. The sealing strip under the
edge of the appliance provides a
sufficient seal for the countertop.
The grouting a and shaded area under
the appliance frame must be flat and
even, so that the frame will lie evenly
and the sealing strip under the edge of
the upper part of the appliance can
provide an adequate seal against the
countertop.
If the appliance is sealed into
position, the countertop or appliance
could be damaged if it needs to be
removed for maintenance or service.
35
Electrical connection
,CAUTION: Before installation or
servicing, disconnect the power
supply by either removing the fuse,
shutting off the main power supply
or manually "tripping" the circuit
breaker.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous and
the manufacturer will not be held
responsible.
Before connecting the appliance to
the power supply, make sure that
the voltage and frequency listed on
the data plate correspond with the
household electrical supply. This
data must correspond to prevent
appliance damage. Consult an
electrician if in doubt.
Only operate the combiset after it
has been installed into the
countertop.
Installer:
Please leave these instructions with
the consumer.
36
Power supply
^ Be sure your electrical supply
matches the data plate.
The combiset is equipped with a
flexible metal conduit encasing 3 wires
ready for connection to a grounded
power supply.
A dedicated line and junction box
should be used to connect the
combiset to a 15 A circuit.
Black wire: connect to L1 (hot)
Red wire: connect to L2 (hot)
Green wire: connect to GND (ground)
240 V, 60 Hz, 15 A fuse rating.
Be sure the power outlet is accessible
after installation.
For further information, see the wiring
diagram provided with the appliance.
, WARNING:
THIS APPLIANCE MUST BE
GROUNDED!
Alteration rights reserved / 4608
For the most updated manual see the Miele web site.
M.-Nr. 07 342 630 / 00