Qpets SP 209 User manual

Please read this guide before using
Thanks you for choosing Qpets. Our mission is to make you a happy pet owner by
providing quality pet products, including the latest tools and technique to successfully
train your pet. If you have any question or comments, please contact out Customer
Support Center at 1-909-923-8743 or visit our website at www.lavasat.com
This is an effective pets training system for small & medium pet which weight under 50
pounds. It can train up to 2 pets at the same time. The Training System has 100 levels
static shock, 100 levels vibration, beep and light function with LCD display. The range is
up to 300 feet.
SP 208 only has one receiver for training 1 pet
SP 209 has two receivers for training 2 pets
Table of Contents
Components…………………………………………………………………2
Function of Transmitter & Receiver……………………………….2
Quick Start Guide…………………………………………………………..3
Step-1 Prepare the remote/transmitter…………………….3
Step-2 Pair transmitter with the collar receiver…………3
Step-3 Install the electrodes for the receiver…………….4
Step-4 Adjust the collar to fit your pet………………………4
How to check the static shock function…………………………5
How to change the battery…………………………………………….5
Important Tips……………………………………………………………….5
Customer Support Center……………………………………………6
1
Components:
1 x Transmitter
(Controller)
1 x Receiver(SP 208
has 1 Receiver
SP 209 has 2
Receivers)
1 x Adjustable
Collar Strap (for
each Receiver)
2 x Pairs of
Electrodes (for each
Receiver)
2 x 6V 4LR44
Batteries (for
Transmitter)
1 x Test Light (for
testing static shock
function)
2 x 1.5V AAA
Batteries (for
each Receiver)
1 x User Manual
Function of Transmitter and Receiver
1. Mode Button (9) for changing different functions (There are 4 functions which
are Static Shock, Vibration, Beep, and Light).
2. “1/2” Button (7) for switch channels. (SP 208 needs to make sure which
Channel
you pair the receiver with, we recommend you to pair receiver with Channel 1)
3. Light Button (6) for the LED Light (2) which on the Transmitter.
4. Y (8) Button is a Launch button for the receiver and also a WORKING BUTTON.
5. Up/Down (5) Button is on the side of transmitter for adjusting the shock and
vibration levels (from 1 to 100).
6. The Transmitter and Receiver will enter Sleep Mode automatically if there is no
activity detected within 2 minutes.
7. There is no display on the LCD Screen when the Transmitter enter Sleep Mode,
please press the Mode Button (9) and Hold for 5 seconds and the Transmitter
will get back to Work Mode.
8. The Green indication light will turn off automatically when receiver enter Sleep
Mode, please gently shake receiver, the receiver will get back to Work Mode.
2
Components:
1 x Transmitter
(Controller)
1 x Receiver(SP 208
has 1 Receiver
SP 209 has 2
Receivers)
1 x Adjustable
Collar Strap (for
each Receiver)
2 x Pairs of
Electrodes (for each
Receiver)
2 x 6V 4LR44
Batteries (for
Transmitter)
1 x Test Light (for
testing static shock
function)
2 x 1.5V AAA
Batteries (for
each Receiver)
1 x User Manual
Function of Transmitter and Receiver
1. Mode Button (9) for changing different functions (There are 4 functions which
are Static Shock, Vibration, Beep, and Light).
2. “1/2” Button (7) for switch channels. (SP 208 needs to make sure which
Channel you pair the receiver with, we recommend you to pair receiver with
Channel 1)
3. Light Button (6) for the LED Light (2) which on the Transmitter.
4. Y (8) Button is a Launch button for the receiver and also a WORKING BUTTON.
5. Up/Down (5) Button is on the side of transmitter for adjusting the shock and
Vibration levels (from 1 to 100).
6. The Transmitter and Receiver will enter Sleep Mode automatically if there is no
activity detected within 2 minutes.
7. There is no display on the LCD Screen when the Transmitter enter Sleep Mode,
Please press the Mode Button (9) and Hold for 5 seconds and the Transmitter
will get back to Work Mode.
8. The Green indication light will turn off automatically when receiver enter Sleep
Mode, please gently shake receiver, the receiver will get back to Work Mode.
2
Quick Start Guide
Step 1: Prepare the Remote Transmitter
Follow the Positive (+) and Negative (-) signs inside of the transmitter and insert the
2 x 6V 4LR44 Batteries into Transmitter. The LCD display will display 000 on the screen.
Step 2: Pair Transmitter with the Collar Receiver
1. Follow the Positive (+) and Negative (-) signs inside of Receiver. Insert the 2 x
1.5V AAA batteries into the 1st Receiver. The receiver will beep and the Green
Indication Light will stay on.
2. Press 1/2 Button to make sure the Transmitter in Channel 1(1 icon shows on the
right of LCD display)
3. Press Y Button and hold for few second on the transmitter until the receiver
beeps. Now the Receiver pair into Channel 1.
4. For SP 209, please follow he Positive (+) and Negative (-) signs inside of Receiver.
Insert the 2 x 1.5V AAA batteries into the 2nd Receiver. The receiver will beep and
the Green Indicated Light will stay on.
5. Press 1/2 Button to make sure the Transmitter in Channel 2(2 icon shows on the
right of LCD display)
6. Press Y Button and hold for few second on the transmitter until the receiver
beeps. Now the Receiver pair into Channel 2.
3
7. Press 1/2 Button to switch to Channel 1, and then press MODE Button to switch
to Vibration Mode ( icon will show on the LCD display).
8. Press Up/Down Button to select a vibration level, and then press Y Button, the
receiver will vibrate.
9. For SP 209, press 1/2 Button to switch to Channel 2, and then press MODE
Button to switch to Vibration Mode ( icon will show on the LCD display).
10. Press Up/Down Button to select a vibration level, and then press Y Button, the
receiver will vibrate.
NOTE:

Please always install the transmitter’s battery BEFORE install the Re batteries
of receivers. As it is a wireless training system, the transmitter has to be power
on then the receiver will be able to receive the code from transmitter.
Step 3: Install the Electrodes for Receivers
Randomly pick on pair of electrodes and screw them on receivers. (Please pick the same
size electrodes for each receiver)
Step 4: Adjust the collar to fit your pet
To ensure a proper fit, please follow the steps below:
1. Put the straps on the receiver.
2. With your dog standing, centre the collar receiver where contact points are
underneath your pet’s neck, touching the skin.
3. The collar receiver should fit snugly, yet loose enough to allow on finger to fit
between the strap and your dog’s neck. If the strap is too long for your dog, cut
off the excess length.
4. Allow your dog to wear the collar for several minutes and then recheck the fit.
Check the fit again as your dog becomes more comfortable wearing the collar
receiver.
We would recommend you to use the Tone Function before starting static
shock and always start with the lowest level of static shock.
4
How to check the static shock function
1. Use the Test Light attach on the both side
of Electrodes (Metal).
2. Press the MODE Button to switch to Shock
Mode, and then press the Up/Down Button
to select a shock level.
3. Press Y Button, the Test Light will blink or
stay on.
How to change the batteries


Please replace the transmitter’s battery when the Battery Exhaustion icon shows
on the LCD display.
Please replace the receiver’s batteries when the Green Indicated Light does not
light up on the receiver.
Important Tips
1. The valid distance of remote control means the straight-line distance
between the transmitter and the receiver without obstacles in between.
If there are interference signals or signal screening around, the actual
remote control distance may vary.
2. The life time of the batteries vary according as how often you use the
product. Your first battery may not last as long as your expect.
3. This product is for pet training. Good effect can only be achieved after a
period of training
4. This product is a wireless transmitting device. You MUST NOT use the
remote control system in places like petrol stations or hospitals where
mobile phones are prohibited. Patients using heart pacemaker are
forbidden to use this product. If some products have the same frequency
as this product, the receiver might not work correctly.
5. The Electrodes have to directly touch pet’s skin as it is very important to
effective training.
6. This product is only for Pet Training, It is not a Regular Pet Collar. Please
remove it from your pet at least 8 hours out of every 24 hours
7. The device does not design for waterproof.
8. If you do not use the transmitter or receiver please take the batteries out
for saving battery life.
5
Customer Support Center
Tel: 1-909-923-8743
Monday – Friday 8:30AM – 5:00 PM Pacific Time
Email:qpets@lavasat.com
Add: LAVA Electronics Inc.
2580 E Philadelphia ST #D
Ontario, CA 91761
This product has a limited Manufacturer Warranty. Details of the warranty can be found
on www.lavasat.com or by calling our Customer Care Center.
Frequency: 433.825 MHZ
Made in China
6
LAVA Electronics Inc
2580 E Philadelphia St #D
Ontario, CA 91761, USA
1-909-923-8743
www.lavasat.com
Email:qpets@lavasat.com
Copyright © LAVA Electronics Inc. 2010. All rights reserved.