Maretron MBB100 User`s manual

®
MBB100
Black Box
Vessel Monitoring and Control
User’s Manual
Revision 1.0
Copyright © 2011 Maretron, LLP All Rights Reserved
Maretron, LLP
9014 N. 23rd Ave #10
Phoenix, AZ 85021-7850
http://www.maretron.com
Maretron Manual Part #: M003003
Revision 1.0
Page i
MBB100 User’s Manual
Revision History
Rev.
1.0
Page ii
Description
Original document.
Revision 1.0
®
Table of Contents
1 2 3 4 5 6 7 8 General .......................................................................................................................................... 1 1.1 Introduction ........................................................................................................................ 1 1.2 Firmware Revision ............................................................................................................. 2 1.3 MBB100 Features .............................................................................................................. 2 1.4 Quick Install........................................................................................................................ 2 Installation...................................................................................................................................... 3 2.1 Unpacking the Box ............................................................................................................. 3 2.2 Choosing a Mounting Location ........................................................................................... 3 2.3 Mounting the MBB100 ........................................................................................................ 3 2.4 Connecting the MBB100 .................................................................................................... 4 2.4.1 RS-232 Connection....................................................................................................... 5 2.4.2 VGA Connection ........................................................................................................... 6 2.4.3 LAN Connection ............................................................................................................ 6 2.4.4 USB Device Connection ............................................................................................... 7 2.4.5 Power Connection......................................................................................................... 7 2.4.6 Power Sequencing ........................................................................................................ 8 2.5 Configuring the MBB100 .................................................................................................... 8 2.5.1 Manually Entering LAN Connection Information ........................................................... 9 2.5.2 Entering N2KServer® or IPG100 Connection Information ........................................... 11 Operating the MBB100 ................................................................................................................ 14 3.1 Turning the MBB100 On................................................................................................... 14 3.2 Turning the MBB100 Off................................................................................................... 14 3.3 Using the MBB100 ........................................................................................................... 14 Maintenance ................................................................................................................................ 15 Troubleshooting ........................................................................................................................... 16 Technical Specifications .............................................................................................................. 17 Technical Support ........................................................................................................................ 18 Maretron (2 Year) Limited Warranty ............................................................................................ 19 Revision 1.0
Page iii
MBB100 User’s Manual
Table of Figures
Figure 1 – MBB100 Network Diagram .................................................................................................. 1 Figure 2 - Mounting Bracket Screw Hole Locations .............................................................................. 4 Figure 3 - Mounting Brackets Attached to MBB100 .............................................................................. 4 Figure 4 - MBB100 Rear Panel Connections ........................................................................................ 5 Figure 5 – MBB100 Front Panel............................................................................................................ 5 Figure 6 – LAN Connection ................................................................................................................... 6 Figure 7 – USB Device Connection ...................................................................................................... 7 Figure 8 - MBB100 Power Terminal Block ............................................................................................ 7 Figure 9 – MBB100 Startup Screen ...................................................................................................... 8 Figure 10 – N2KView® Window with Tabs Displayed ............................................................................ 9 Figure 11 – Configuration Dialog ........................................................................................................ 10 Figure 12 – N2KView® Window with Tabs Displayed .......................................................................... 11 Figure 13 – Connections Settings Dialog ............................................................................................ 12 Page iv
Revision 1.0
®
1 General
1.1
Introduction
Congratulations on your purchase of the Maretron MBB100 Black Box for Vessel Monitoring and
Control. Maretron has designed and built your black box to the highest standards for years of
dependable and accurate service.
The Maretron Black Box (MBB100) is a dedicated processing unit that comes preloaded with
Maretron’s N2KView® vessel monitoring and control software (N2KView® hardware license key sold
separately). Unlike a PC that allows any software to be loaded, the MBB100 runs only N2KView®
software making it extremely stable and dedicated to monitoring and controlling your vessel.
The MBB100 is ruggedized for marine use and includes a solid state disk drive to withstand the
pounding associated with waves. And since the MBB100 dissipates less than 20 watts, there is no
need for internal cooling fans that are noisy and wear out causing electronics to overheat and fail.
The MBB100 connects to a monitor through a VGA connector and associated touch screen through a
USB or serial port connection. Alternatives to controlling the N2KView® software through a touch
screen include keyboards, mice, or track balls connected through USB. The MBB100 has an Ethernet
port for communicating with an NMEA 2000® network (see Figure 1) through Maretron’s Internet
Protocol Gateway (IPG100). Alternatively, the MBB100 can network through Ethernet to a PC running
N2KServer®. Although the MBB100 comes pre-installed with the N2KView® software, a separately
purchased N2KView hardware license key plugged into the IPG100 (or PC) is required (see IPG100
User’s Manual for more details). The Ethernet port is also used for connecting Internet Protocol (IP)
cameras for viewing within the N2KView® software.
Figure 1 – MBB100 Network Diagram
Revision 1.0
Page 1
MBB100 User’s Manual
Of course you get the same flexibility using Maretron’s N2KView® software from the MBB100 as you
would running the software on a PC, which includes the ability to configure as many screens as you
want with exactly the information you want to see. Plus you get free upgrades to the software as
improvements and new features are added.
The Maretron MBB100 is designed to operate within the harsh demands of the marine environment.
However, no piece of marine electronic equipment can function properly unless installed, configured,
and maintained in the correct manner. Please read carefully and follow these instructions for
installation, configuration, and usage of the Maretron MBB100 in order to ensure optimal
performance.
1.2
Firmware Revision
This manual corresponds to the MBB100 running N2KView® Version 3.2.
1.3
MBB100 Features
The Maretron MBB100 has the following features.
• Full version of N2KView® software preinstalled (requires N2KView® licenses, purchased
separately)
• Wired Ethernet interface
• Supports user-supplied VGA monitor
• Supports user-supplied touchscreen (ELO, 3M Microtouch, Hampshire TSharc, Penmount)
• Supports user-supplied mouse and keyboard
• Supports Bluetooth mice and keyboards with built-in Bluetooth adapter
• Operates on 9-36VDC
• 20W power consumption
• Solid State Disk Drive
• Fanless cooling system
1.4
Quick Install
Installing the Maretron MBB100 display involves the following four steps. Please refer to the individual
sections for additional details.
• Unpacking the Box (Section 2.1)
• Choosing a Mounting Location (Section 2.2)
• Mounting the MBB100 (Section 2.3)
• Connecting the MBB100 (Section 2.4)
• Configuring the MBB100 (Section 2.5)
Page 2
Revision 1.0
®
2 Installation
2.1
Unpacking the Box
When unpacking the box containing the Maretron MBB100, you should find the following items:
•
•
•
•
•
•
•
•
•
1 – MBB100 Maretron Black Box Vessel Monitoring and Control
2 – Mounting Brackets
1 – Short Screw Set (Used for Mounting Bracket)
1 – AC Power Cord
1 – AC Power Supply
1 – Rubber Feet/Long Screw Set
1 – MBB100 User’s Manual
1 – N2KView® Documentation CD-ROM
1 – Warranty Registration Card
If any of these items are missing or damaged, please contact Maretron.
2.2
Choosing a Mounting Location
The MBB100 must be mounted in an indoor location.
2.3
Mounting the MBB100
The MBB100 can be mounted to a wall or other flat surface with the included mounting brackets.
2.6.1 Mounting the System with Mounting Brackets
To mount the MBB100 onto a wall or some other surface using the two mounting brackets, please
follow the steps below.
Step 1: Turn the MBB100 over.
Step 2: Align the two retention screws holes in each bracket with the corresponding retention screw
holes on the sides of the MBB100 bottom surface (marked in yellow in Figure 2).
Step 3: Secure the brackets to the MBB100 by inserting two retention screws into each bracket (see
Figure 2).
Step 4: Drill holes in the intended installation surface.
Step 5: Align the mounting holes in the sides of the mounting brackets with the predrilled holes in the
mounting surface.
Step 6: Insert four retention screws, two in each bracket, to secure the MBB100 to the wall.
Revision 1.0
Page 3
MBB100 User’s Manual
Figure 2 - Mounting Bracket Screw Hole Locations
Figure 3 - Mounting Brackets Attached to MBB100
2.4
Connecting the MBB100
Most I/O interface connections of the MBB100 are found on rear panel (see
Figure 4). The I/O interface panel located on the rear of the MBB100 has the following I/O interface
connectors:
• 2 x 9-36VDC power connectors
• 1 x Audio line-out jack
• 1 x Reset button
• 1 x RS-232 serial interface connector
• 1 x RJ-45 Gigabit Ethernet LAN ports
• 2 x USB 2.0 connectors
Page 4
Revision 1.0
®
Figure 4 - MBB100 Rear Panel Connections
The I/O interface panel located on the front of the MBB100 (see Figure 5) has two USB 2.0 interface
connectors.
Figure 5 – MBB100 Front Panel
2.4.1 RS-232 Connection
There is one external RS-232 connector. The RS-232 connector enables connection to an external
touch screen. To connect a serial cable with the RS-232 connector, please follow the instructions
below.
Step 1: Locate the RS-232 connector on the rear panel of the MBB100.
Step 2: Align the RS-232 connector on the serial cable with the RS-232 connector on the rear panel
of the MBB100.
Revision 1.0
Page 5
MBB100 User’s Manual
Step 3: Once aligned, gently insert the serial cable RS-232 connector into the MBB100 RS-232
connector.
2.4.2 VGA Connection
There is one external VGA connector. The VGA connector enables connection to an monitor. To
connect a VGA cable with the VGA connector, please follow the instructions below.
Step 1: Locate the VGA connector on the rear panel of the MBB100.
Step 2: Align the VGA connector on the cable with the VGA connector on the rear panel of the
MBB100.
Step 3: Once aligned, gently insert the cable VGA connector into the MBB100 VGA connector.
2.4.3 LAN Connection
There is one external RJ-45 LAN connector. The RJ-45 connector enables connection to an external
network. To connect a LAN cable with the RJ-45 connector, please follow the instructions below.
Step 1: Locate the RJ-45 connector on the rear panel of the MBB100.
Step 2: Align the RJ-45 connector on the LAN cable with the RJ-45 connector on the rear panel of
the MBB100 (see Figure 6).
Figure 6 – LAN Connection
Step 3: Once aligned, gently insert the LAN cable RJ-45 connector into the onboard RJ-45
connector.
Page 6
Revision 1.0
®
2.4.4 USB Device Connection
There are four external USB 2.0 connectors. To connect a USB 2.0 or USB 1.1 device, please follow
the instructions below.
Step 1: The locations of the USB connectors are shown in and Figure 5.
Step 2: Align the USB device connector with one of the connectors (see Figure 7).
Figure 7 – USB Device Connection
Step 3: Once aligned, gently insert the USB device connector into the MBB100 connector.
2.4.5 Power Connection
The MBB100 can be connected to a power source in one of two ways (over current protection should
be provided and should be sized in accordance with ABYC E-11, AC and DC ELECTRICAL
SYSTEMS ON BOATS);
1) Directly with 9-32VDC power source using the green power terminal block found on the rear panel
of the MBB100 (see Figure 8).
a) Connect the power source negative terminal to the right hand terminal,
b) Connect the power source positive terminal to the center terminal.
Figure 8 - MBB100 Power Terminal Block
2) Indirectly with 100-240VAC 47-63Hz power source using the AC power adapter and the AC power
cord supplied in the box.
a) Connect the AC power cord to the AC power adapter,
b) Connect the AC power cord to the AC power outlet,
Revision 1.0
Page 7
MBB100 User’s Manual
c) Connect the 12VDC connector from the AC power adapter to the MBB100’s 12VDC power
input connector.
2.4.6 Power Sequencing
When the MBB100 is connected to an appropriate power source, you can use the power switch
located on the front panel (see Figure 5) to turn the MBB100 on or off. If the MBB100 is turned on,
then the LED found behind the power button will be illuminated blue. If the power switch is pushed to
power down the DSM800, the LED is turned off.
The MBB100 can also be switched on and off by applying or removing power through an external
switch or breaker. Anytime the power is reapplied to the MBB00, it will turn on.
2.5
Configuring the MBB100
In order to use the MBB100, you must already have N2KServer® installed and running on either a
Windows PC or on a Maretron IPG100 Internet Protocol Gateway.
You must also have some information as to the configuration of your local area network.
The MBB100 will start up with the following warning screen:
Figure 9 – MBB100 Startup Screen
You are required to press Accept and thereby acknowledge this warning message before N2KView®
will run in Live Mode.
Page 8
Revision 1.0
®
Alternatively, you may Enter Demo Mode. In Demo Mode, you will not be able to connect to a Server
and view live data; instead simulated data will be provided to stimulate the controls.
The first time you start the MBB100, you must ensure that the device can connect to your LAN (local
area network). The MBB100 comes from the factory preconfigured to obtain its LAN connection
information from a DHCP (Dynamic Host Control Protocol) server. If your local area network uses a
DHCP server, no configuration is necessary, and the MBB100 should be able to successfully connect
to the local area network.
2.5.1 Manually Entering LAN Connection Information
If your local area network does not use DHCP, you must manually enter the LAN connection
information into the MBB100. This is done through the following steps:
Figure 10 – N2KView® Window with Tabs Displayed
a.
b.
Click anywhere inside the N2KView® screen to display the screen tabs as shown in Figure 10
above.
Click on the “Configuration” tab on the right side of the N2KView® screen to display the
Configuration dialog.
Revision 1.0
Page 9
MBB100 User’s Manual
Figure 11 – Configuration Dialog
c.
Uncheck the “Use DHCP” box to indicate that your LAN does not use DHCP.
d.
In the “IP Address” field, enter the IP address you wish to assign to the MBB100.
e.
In the “Netmask” field, enter the netmask value used on your LAN (in most cases, this value
will be “255.255.255.0”).
f.
In the “Gateway” field, enter the IP address of the default gateway of your LAN.
g.
In the “Name Server” field, enter the IP address of a DNS (Dynamic Name Service) Server
used on your LAN.
h.
Click the “Update” button to make these changes permanent. The screen will go blank for a
few seconds while this is being done.
Page 10
Revision 1.0
®
2.5.2 Entering N2KServer® or IPG100 Connection Information
Once the MBB100 has been properly configured to connect to your LAN, you must configure the
connection to enable the MBB100 to receive information from an instance of N2KServer® or an
IPG100 Server. This is done through the following steps:
Figure 12 – N2KView® Window with Tabs Displayed
a.
Click anywhere inside the N2KView® screen to display the screen tabs as shown in Figure 12
above.
b.
Click on the “Connections” tab on the right side of the N2KView® screen to display the
Connections Settings dialog.
Revision 1.0
Page 11
MBB100 User’s Manual
Figure 13 – Connections Settings Dialog
c.
Ensure that N2KView® is not connected to a N2KServer® by pressing the “Disconnect” button.
While N2KView® is connected you are not able to edit fields.
d.
In the “Hostname / IP Address:” text box, enter the IP address of the computer or IPG100
running N2KServer®. If your MBB100 configuration has been programmed to match your LAN,
the left side of the N2KServer® Connection window will display the address of any N2KServer®
running on a PC or IPG100’s found on the LAN.
e.
Leave the “Port:” setting at the initial value of “6544” unless the router between N2KView® and
N2KServer® has been set up to do port translation.
f.
In the “Password:” text box, enter the same server password that you entered into the
N2KServer® Service Manager (for N2KServer® running on a PC)¸ or programmed into the
IPG100.
g.
If you have purchased the Platinum Edition of N2KView® and wish to use all of the Platinum
Edition features, select “Platinum” from “Features Requested:”. If you have purchased the
Basic Edition of N2KView® or you wish to use only the BasicEdition subset of features of
N2KView® (leaving the Platinum Edition features available for another copy of N2KView®),
select “Basic” from “Features Requested:”.
h.
Click “Connect”. The “Connection State:” part of the window will blink “Connecting…” for a
few seconds. It will then either display “Connected” if the connection was successfully made,
or display a message indicating that the connection was not made and suggesting further
action to take.
Page 12
Revision 1.0
®
If no data is displayed, please check the following:
1.
Make sure the “Server Password” entered in N2KView® matches the “Server Password”
entered into the N2KServer® Service Manager on the computer running N2KServer®, or the
IPG100, as appropriate. If the server is running on an IPG100, the password in the IPG100 is
set from a DSM250 or N2KAnalyzer®.
2.
Make sure the “Server Address” matches the IP address of the computer or IPG100 running
N2KServer®.
3.
Make sure you have appropriate instruments on the NMEA 2000® network to provide the data
you are trying to view on the N2KView® screen. (To test the network connection between
N2KView® and the N2KServer®, you may wish to run N2KServer® in “Simulated Data” mode).
4.
Make sure that the instances that are being monitored correspond to the instances being
transmitted. You can set the instance number of the component to “Any” to make sure that
there is any data of that type on the bus.
Revision 1.0
Page 13
MBB100 User’s Manual
3 Operating the MBB100
3.1
Turning the MBB100 On
To turn on the MBB100, press the power switch, located on the right hand side of the front panel of
the MBB100.
3.2
Turning the MBB100 Off
To turn the MBB100 off, use the “Shutdown” administrative tab of the N2KView® software.
Alternatively, you can power down the unit by pressing the MBB100’s power switch. Lastly, you can
power down the unit by turning of the power source with an external breaker or external switch.
3.3
Using the MBB100
The MBB100 runs a fully functional version of the Maretron N2KView® software. Please refer to the
N2KView® User’s Manual, packaged with the MBB100, for detailed operating instructions.
Page 14
Revision 1.0
®
4 Maintenance
Regular maintenance is important to ensure continued proper operation of the Maretron
MBB100. Perform the following tasks periodically:
•
•
•
Clean the unit with a soft cloth. Do not use chemical cleaners as they may remove paint or
markings or may corrode the MBB100 enclosure or seals. Do not use any cleaners containing
acetone, as they will deteriorate the plastic enclosure. Do not spray cleaning liquids directly
onto the MBB100.
Ensure that the unit is mounted securely and cannot be moved relative to the mounting
surface. If the unit is loose, tighten the mounting screws.
Check the security of the power and network cables connected to the MBB100 and tighten if
necessary.
Revision 1.0
Page 15
MBB100 User’s Manual
5 Troubleshooting
If you notice unexpected operation of the Maretron MBB100, follow the troubleshooting
procedures in this section to remedy simple problems.
Symptom
No activity on the display
Other Issues
Troubleshooting Procedure
Check the connection to the power and network
connectors and tighten if necessary
Ensure that power is supplied to the connected
power cable.
Check the connection to the power jack located on
the rear of the device.
Press the power switch located on the front of the
device on the right-hand side.
Please refer to the Troubleshooting section of the
N2KView® User’s Manual.
If these steps do not solve your problem, please contact Maretron Technical Support (refer to Section
0 for contact information).
Warning: There are no user-serviceable components inside the Maretron MBB100. Opening the
MBB100 will expose the sensitive electronic components to adverse environmental conditions that
may render the unit inoperative. Please do not open the MBB100, as this will automatically void the
warranty. If service is required, please return the unit to an authorized Maretron service location.
Page 16
Revision 1.0
®
6 Technical Specifications
Specifications
Parameter
Video Connector
USB Connector
Serial Connector
Ethernet Connector
Audio Connection
Value
Comment
One VGA Port (RGB or D-sub 15) For Monitor Connection
Four USB 2.0 connections
For connecting Peripherals (Mouse,
keyboard, etc.) and or touch screen
connectivity
One RS232 9-Pin D Connector For touch screen alternative connection
One RJ-45 GbE
For connection to Maretron IPG100
Gateway and/or router
One Speaker Output
Certifications
Parameter
Comment
Electromagnetic Compatibility
FCC class A and CE Mark
Electrical
Parameter
Operating Voltage
Power Consumption (Maximum)
Value
9 to 36 Volts
19 Watts
Comment
DC Voltage
Mechanical
Parameter
Overall Dimensions (DxWxH)
Weight
Chassis Material
Mounting
Value
5.19” x 9.02” x 2.52”
(132mm x 229mm x
64mm)
4.6 lbs (2.1kg)
Aluminum
VESA 100 or DIN
Comment
Including Flanges for Mounting
Any Orientation
Environmental
Parameter
Operating Temperature
Operating Shock
Vibration
Revision 1.0
Value
-10°C to 60°C
Half-sine wave shock 3G; 11 ms; 3 shocks per axis
MIL-STD-810F 514.5C-2
Page 17
MBB100 User’s Manual
7 Technical Support
If you require technical support for Maretron products, you can reach us in any of the following ways:
Telephone: 1-866-550-9100
Fax: 1-602-861-1777
E-mail:
support@maretron.com
World Wide Web: http://www.maretron.com
Mail: Maretron, LLP
Attn: Technical Support
9014 N. 23rd Ave Suite 10
Phoenix, AZ 85021 USA
Page 18
Revision 1.0
®
8
Maretron (2 Year) Limited Warranty
Maretron warrants the MBB100 to be free from defects in materials and workmanship for two (2)
years from the date of original purchase. If within the applicable period any such products shall be
proved to Maretron’s satisfaction to fail to meet the above limited warranty, such products shall be
repaired or replaced at Maretron’s option. Purchaser's exclusive remedy and Maretron’s sole
obligation hereunder, provided product is returned pursuant to the return requirements below, shall be
limited to the repair or replacement, at Maretron’s option, of any product not meeting the above
limited warranty and which is returned to Maretron; or if Maretron is unable to deliver a replacement
that is free from defects in materials or workmanship, Purchaser’s payment for such product will be
refunded. Maretron assumes no liability whatsoever for expenses of removing any defective product
or part or for installing the repaired product or part or a replacement therefore or for any loss or
damage to equipment in connection with which Maretron’s products or parts shall be used. With
respect to products not manufactured by Maretron, Maretron’s warranty obligation shall in all respects
conform to and be limited to the warranty actually extended to Maretron by its supplier. The foregoing
warranties shall not apply with respect to products subjected to negligence, misuse, misapplication,
accident, damages by circumstances beyond Maretron’s control, to improper installation, operation,
maintenance, or storage, or to other than normal use or service.
THE FOREGOING WARRANTIES ARE EXPRESSLY IN LIEU OF AND EXCLUDES ALL OTHER
EXPRESS OR IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE.
Statements made by any person, including representatives of Maretron, which are inconsistent or in
conflict with the terms of this Limited Warranty, shall not be binding upon Maretron unless reduced to
writing and approved by an officer of Maretron.
IN NO CASE WILL MARETRON BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,
DAMAGES FOR LOSS OF USE, LOSS OF ANTICIPATED PROFITS OR SAVINGS, OR ANY
OTHER LOSS INCURRED BECAUSE OF INTERRUPTION OF SERVICE. IN NO EVENT SHALL
MARETRON’S AGGREGATE LIABILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT(S)
INVOLVED. MARETRON SHALL NOT BE SUBJECT TO ANY OTHER OBLIGATIONS OR
LIABILITIES, WHETHER ARISING OUT OF BREACH OF CONTRACT OR WARRANTY, TORT
(INCLUDING NEGLIGENCE), OR OTHER THEORIES OF LAW WITH RESPECT TO PRODUCTS
SOLD OR SERVICES RENDERED BY MARETRON, OR ANY UNDERTAKINGS, ACTS OR
OMISSIONS RELATING THERETO.
Maretron does not warrant that the functions contained in any software programs or products will
meet purchaser’s requirements or that the operation of the software programs or products will be
uninterrupted or error free. Purchaser assumes responsibility for the selection of the software
programs or products to achieve the intended results, and for the installation, use and results
obtained from said programs or products. No specifications, samples, descriptions, or illustrations
provided Maretron to Purchaser, whether directly, in trade literature, brochures or other documentation
shall be construed as warranties of any kind, and any failure to conform with such specifications,
samples, descriptions, or illustrations shall not constitute any breach of Maretron’s limited warranty.
Revision 1.0
Page 19
MBB100 User’s Manual
Warranty Return Procedure:
To apply for warranty claims, contact Maretron or one of its dealers to describe the problem and
determine the appropriate course of action. If a return is necessary, place the product in its original
packaging together with proof of purchase and send to an Authorized Maretron Service Location. You
are responsible for all shipping and insurance charges. Maretron will return the replaced or repaired
product with all shipping and handling prepaid except for requests requiring expedited shipping (i.e.
overnight shipments). Failure to follow this warranty return procedure could result in the product’s
warranty becoming null and void.
Maretron reserves the right to modify or replace, at its sole discretion, without prior notification, the
warranty listed above. To obtain a copy of the then current warranty policy, please go to the following
web page:
http://www.maretron.com/company/warranty.php
Page 20
Revision 1.0