Eiki EIP-X350 User`s manual

—i—
User’s Manual
Copyright
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may
be reproduced without written consent of the author.
© Copyright June, 2006
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and
pending applications in other countries throughout the world.
All other product names used in this manual are the properties of their respective owners and are
acknowledged.
—i—
— ii —
Preface
Important Safety Information
Congratulations on purchasing the Planar DLP® projector!
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause
personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
Remote Control
Some remote controls have a laser for pointing out items on a screen.
DANGER: Do not point the laser in the eyes. Doing so can damage the eyes permanently.
General Safety Information
¾
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
¾
Follow all warnings and cautions in this manual and on the unit case.
¾
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
¾
Do not place the unit on an unstable surface, cart, or stand.
¾
Avoid using the system near water, in direct sunlight, or near a heating device.
¾
Do not place heavy objects such as books or bags on the unit.
— ii —
– iii –
User’s Manual
Power Safety
¾
Only use the supplied power cord.
¾
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
¾
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. Refer to “Replacing the Projection Lamp” on
page 33 for clear and safe instructions for this procedure. Before replacing the lamp:
¾
Unplug the power cord.
¾
Allow the lamp to cool for about one hour.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Cleaning the Projector
¾
Unplug the power cord before cleaning. Refer to “Cleaning the Projector” on page 36.
¾
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the “Regulatory Compliance”
section on page 46.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of seperate recycling collection services.
— iv —
— iii —
Preface
Main Features
•
Lightweight unit, easy to pack away and transport
•
Compatible with all major video standards including NTSC, PAL, and SECAM
•
A high brightness rating allows for presentations in daylight or in lit rooms
•
Supports resolutions up to SXGA+ at 16.7 million colors to deliver crisp, clear images
•
Flexible setup allows for front , rear & ceiling mounted projections
•
Line-of-vision projections remain square, with advanced keystone correction for angled
projections
•
Input source automatically detected
Register Your Planar Products Today
Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services,
registeryour Planar product today. Visit our website to register your product at
http://www.planar.com/support/product_registration.html
Cables, Replacement Lamps and Accessories
To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touchscreen or
other Planar products visit our online store at www.PlanarOnline.com or find other stores who carry Planar
products at http://www.planar.com/howtobuy
About this manual
This manual is intended for end users and describes how to install and operate the DLP® projector.
Wherever possible, relevant information—such as an illustration and its description—has been kept on
one page. This printer-friendly format is both for your convenience and to help save paper, thereby
protecting the environment. It is suggested that you only print sections that are relevant to your needs.
—–ivv –—
User’s Manual
Table of contents
GETTING STARTED .......................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2
Front-right View ............................................................................................................................................................. 2
Top view—On-screen Display (OSD) buttons and LEDs ............................................................................................... 3
Rear view ........................................................................................................................................................................ 5
Bottom view..................................................................................................................................................................... 6
REMOTE CONTROL PARTS ................................................................................................................................................... 7
REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 9
PROJECTOR AND REMOTE CONTROL BUTTONS .................................................................................................................... 9
SETUP AND OPERATION............................................................................................................................................... 10
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................. 10
CONNECTING INPUT DEVICES ............................................................................................................................................ 11
STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 13
SETTING AN ACCESS PASSWORD (SECURITY LOCK) .......................................................................................................... 15
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 16
ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ................................................................................................................ 17
ADJUSTING THE VOLUME .................................................................................................................................................. 17
ON-SCREEN DISPLAY (OSD) MENU SETTINGS....................................................................................................... 19
OSD MENU CONTROLS ..................................................................................................................................................... 19
Navigating the OSD ...................................................................................................................................................... 19
SETTING THE OSD LANGUAGE .......................................................................................................................................... 20
MAIN MENU ...................................................................................................................................................................... 22
Main Menu Functions Available for Connected Source ............................................................................................... 23
SETUP MENU ..................................................................................................................................................................... 24
Setup Menu Functions Available for Connected Source............................................................................................... 24
Advance Feature ........................................................................................................................................................... 25
User Color .................................................................................................................................................................... 27
CONFIG MENU ................................................................................................................................................................... 28
UTILITY MENU .................................................................................................................................................................. 29
Utility Menu Functions Available for Connected Source ............................................................................................. 30
TOOL MENU ...................................................................................................................................................................... 31
STATUS MENU ................................................................................................................................................................... 32
MAINTENANCE AND SECURITY................................................................................................................................. 33
REPLACING THE PROJECTION LAMP................................................................................................................................... 33
Resetting the Lamp........................................................................................................................................................ 36
CLEANING THE PROJECTOR................................................................................................................................................ 36
Cleaning the Lens ......................................................................................................................................................... 37
Cleaning the Case ......................................................................................................................................................... 37
USING THE KENSINGTON® LOCK ...................................................................................................................................... 37
TROUBLESHOOTING ..................................................................................................................................................... 38
COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 38
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 38
LED ERROR MESSAGES ..................................................................................................................................................... 39
IMAGE PROBLEMS .............................................................................................................................................................. 39
LAMP PROBLEMS ............................................................................................................................................................... 40
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 40
AUDIO PROBLEMS ............................................................................................................................................................. 40
SPECIFICATIONS............................................................................................................................................................. 41
Input/output connectors ................................................................................................................................................ 41
PROJECTION DISTANCE V.S. PROJECTION SIZE .................................................................................................................. 42
PR3020 and PR3010 Projection distance and size table .............................................................................................. 42
PR5020 Projection distance and size table................................................................................................................... 43
TIMING MODE TABLE ........................................................................................................................................................ 44
—
—
— vi
v—
Preface
REGULATORY COMPLIANCE ..................................................................................................................................... 46
FCC WARNING .................................................................................................................................................................. 46
CANADA ............................................................................................................................................................................ 46
SAFETY CERTIFICATIONS ................................................................................................................................................... 46
FCC CLASS B, UL, C-UL, CE, CB, TUV-GS, CCC , ICES-003(CLASS B) ....................................................................... 46
EN 55022 WARNING ......................................................................................................................................................... 46
– vii—– vi —
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
REMOTE CONTROL
(WITH TWO AAA BATTERIES)
DLP® PROJECTOR
POWER CORD
USB CABLE
(USB TYPE A-TO-B USB)
COMPOSITE VIDEO CABLE
(RCA 3-TO-RCA 3)
COMPUTER CABLE
(VGA-VGA)
AUDIO CABLE
(MINI JACK-TO-MINI JACK)
CD-ROM (THIS USER’S
MANUAL)
USERS GUIDE
CARRYING CASE
.
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.
Caution:
Avoid using the projector in dusty environments.
–1–
User’s Manual
Views of Projector Parts
Front-right View
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
Focus
Focuses the projected image
17
2.
Lens zoom
Enlarges the projected image
17
3.
Screws
Holds lamp to projector
4.
See “Top view—OSD buttons and LEDs”
3
5.
Front IR receiver
Receiver for IR signal from remote control
7
6.
Lens
Slide lens cap before use.
7.
Lens cover
Slide across to protect lens when not in use
–2–
DLP® Projector – User’s Manual
8.
Height-adjuster button
Push to release height adjuster
16
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
Top view—On-screen Display (OSD) buttons and LEDs
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
Keystone/
Down cursor
Corrects image-trapezoid (wider bottom) effect
Navigates and changes settings in the OSD
19
2.
VOL-/
Left cursor
Decreases volume
Navigates and changes settings in the OSD
19
3.
Ready LED
Orange
Lamp ready—you can safely turn on or off the projector
Flashing
Lamp not ready—do not press the power button
4.
Keystone/
UP cursor
Corrects image-trapezoid (wider top) effect
Navigates and changes settings in the OSD
5.
Power LED
Green
Unit is powered on and working correctly
Off
Unit is powered off
Flashing
Operational error code
(refer to “LED Error Messages” on page 39)
6.
Enter
Changes settings in the OSD
–3–
19
19
User’s Manual
7.
VOL+/
Right cursor
Increases volume
Navigates and changes settings in the OSD
8.
Auto
Optimizes image size, position, and resolution
Navigates and changes settings in the OSD
9.
Menu
Opens and exits the OSD
19
13
10.
Source
Detects the input device
11.
Power
Turns the projector on or off
–4–
DLP® Projector – User’s Manual
Rear view
ITEM
LABEL
1.
Rear IR receiver
2.
DVI-D
DESCRIPTION
Receiver for IR signal from remote control
SEE
PAGE:
7
Connect a DVI-D cable (not supplied) from a computer
(For PR5020 only)
3.
VGA IN
Connect a VGA cable (supplied) from a computer
4.
VGA OUT
Connect to a monitor (not supplied)
5.
S-video
Connect the S-video cable (not supplied) from a video device
6.
Video
Connect a composite video cable (supplied) from a video
device.
7.
Audio in-R
Connect the audio cable (supplied) from an audio input device.
8.
Audio in-L
Connect the audio cable (supplied) from an audio input device.
9.
Audio-in
Connect an audio cable(supplied) from the computer’s audio-out
connector.
10.
Audio-out
Audio loop-thru
11.
USB
Connect the USB cable (supplied) from a computer
12.
RS-232
11
Installation control
(For PR5020 only)
13.
Power
Connect the power cord (supplied)
–5–
13
User’s Manual
14.
Security Lock
Secure to permanent object with a Kensington® Lock
system
37
Note:
If your video equipment has both S-video and RCA jacks (composite video) connect to the S-video
connector.
S-video provides a better quality signal.
Bottom view
ITEM
LABEL
DESCRIPTION
1.
Ceiling support holes
Contact your dealer for information on mounting
the projector on a ceiling.
2.
Height adjuster button
Push to release height adjuster
3.
Height adjuster
Adjuster drops down when adjuster button is
pushed
4.
Tilt adjuster
Adjust angle of the picture
–6–
SEE PAGE:
16
DLP® Projector – User’s Manual
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency
fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path
between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
ITEM
LABEL
DESCRIPTION
1.
IR transmitter
Transmits signals to projector
2.
Status LED
Lights when the remote control is used
3.
Laser
Press to operate the on-screen pointer
4.
Up
Up arrow when connected through USB to a PC
5.
Right
Right arrow when connected through USB to a PC
6.
Down
Down arrow when connected through USB to a PC
–7–
SEE PAGE:
User’s Manual
ITEM
LABEL
7.
Page Down
8.
Up cursor
9.
Right cursor
10.
Down cursor
11.
DESCRIPTION
SEE PAGE:
Page down when connected through USB to a PC
Navigates and changes settings in the OSD
19
Volume +/-
Adjusts volume
17
12.
Mute
Mutes the built-in speaker
13.
Zoom+
Zoom in
14.
Zoom-
Zoom out
15.
Freeze
Freeze/unfreezes the on-screen picture
16.
Blank
Makes the screen blank
17.
Source
Detects the input device
18.
Auto
Auto adjustment for phase, tracking, size, position
19.
Menu
Opens the OSD
19
20.
Status
Opens the OSD Status menu (the menu only opens
when an input device is detected)
32
21.
Keystone
top/bottom
Corrects image-trapezoid (wider top/bottom) effect
22.
Left cursor
Navigates and changes settings in the OSD
23.
Enter
Changes settings in the OSD
24.
Page Up
Page up when connected through USB to a PC
25.
Left
Left arrow when connected through USB to a PC
26.
Enter
Enter key when connected through USB to a PC
27.
Power
Turns the projector on or off
28.
Laser
Use as on-screen pointer. DO NOT POINT IN EYES.
17
19
13
Note:
The remote control can only interface with a computer when connected to the computer through a
USB cable connection. The computer cable connects a computer to the projector for display
purposes only.
–8–
DLP® Projector – User’s Manual
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 10 meters (33 feet) and
30 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however the buttons on the projector are
limited in use. The following illustration shows the corresponding buttons on the remote control and
on the projector.
Some buttons on the projector have two functions. For example, item 10/13 on the projector functions
both keystone button and as the up cursor key in OSD menus.
–9–
SETUP AND OPERATION
Inserting the Remote Control Batteries
1.
2.
3.
Remove the battery compartment cover
by sliding the cover in the direction of
the arrow.
Insert the supplied batteries taking note
of the polarity (+/-) as shown here.
Replace the cover.
Caution:
1. Only use AAA alkaline batteries.
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
– 10 –
DLP® Projector – User’s Manual
Connecting Input Devices
A PC or notebook computer as well as video devices can be connected to the projector at the same
time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital
still cameras. Check the user manual of the connecting device to confirm it has the appropriate output
connector.
ITEM
LABEL
DESCRIPTION
A
Rear IR
B
DVI-D
C
VGA in
Connect a VGA cable (supplied) from a computer.
D
VGA out
Connect a VGA cable (not supplied) to a monitor.
E
S-video
Connect S-video cable (not supplied) from a video device.
F
Video
Connect a composite video cable (supplied) from a video device.
G
Audio in-R
Connect the audio cable (supplied) from an audio input device.
H
Audio in-L
Connect the audio cable (supplied) from an audio input device.
Audio-in
Connect an audio cable (supplied) from the computer’s audio-out
connector.
Audio-out
Audio loop-thru
USB
Connect the supplied USB cable (supplied) from a computer for USB
mouse function and firmware upgrades.
I
Receiver for IR signal from remote control.
Connect DVI-D cable (not supplied) from a computer.
(For PR5020 only)
RS-232
(For PR5020 only)
Reserved for installation control.
– 11 –
User’s Manual
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
– 12 –
DLP® Projector – User’s Manual
Starting and Shutting down the Projector
1.
2.
3.
4.
Slide the lens cover.
Connect the power cord to the projector [A]
Connect the other end to a wall outlet.
Switch [B] from on (O) to off ( — )
The POWER and READY LEDs on the
projector turn on.
Turn on the connected devices.
Ensure the Ready LED is on a steady (not
flashing) orange and then press the Power
button to turn on the projector.
The projector splash screen displays and
connected devices are detected.
If the connected device is a PC, press the
appropriate keys on the computer keyboard to
switch the display output to the projector.
(Check the user manual of the PC to
determine the appropriate Fn key combination
to change display output.)
See “Setting an Access Password (Security
Lock)” on page 15 if Security Lock is
enabled.
5.
6.
If more than one input device is connected,
press the Source button repeatedly to switch
among devices.
(DVD and HDTV are supported through the
VGA connector.)
To turn off the projector, press the Power
button. The projector prepares for shutdown
and a “Wait a moment please…” message
appears.
– 13 –
User’s Manual
7.
When the “Power Off?/Press Power again”
message appears, press the Power button.
The projector turns off.
8.
Turn off the main Power switch when the
Ready LED stops flashing.
.
Caution:
Do not unplug the power cord until the Ready LED stops flashing, indicating the projector has
cooled down.
– 14 –
DLP® Projector – User’s Manual
Setting an Access Password (Security Lock)
You can use the cursor (arrow) buttons to set a password and prevent unauthorized use of the
projector. When enabled, the password must be entered after you power on the projector. (See
“Navigating the OSD” on page 32 and “Setting the OSD Language” on page 32 for help on using
OSD menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the projector.
If you lose the password, contact your reseller for information on clearing the password.
1.
2.
3.
4.
5.
6.
Press the Menu button to open the OSD
menu.
Press the cursor
Setup menu.
button to move to the
Press the cursor
button to select
Advance Feature and press Enter or
Press the cursor
Security Lock.
.
button to select
Press the cursor Enter or button to
select Enable. (White text is selected.)
A password dialog box automatically
appears.
You can only use the following four
cursor buttons:
in the password fields. You can use any
combination including the same arrow five
times, but not less than six.
Press the cursor buttons in any order to set
the password. When you confirm the
password, OK appears.
Every time you start the projector, a
password dialog box appears.
Enter the password in the order you set it
at step 6. (Press the Menu button to cancel
if you enter the wrong password.)
– 15 –
User’s Manual
Adjusting the Projector Level
Take note of the following when setting up the projector:
•
The projector table or stand should be level and sturdy.
•
Position the projector so that it is perpendicular to the screen.
•
Be sure cables are not in the way or can cause the projector to be knocked over.
6.
To raise the level of the projector, lift the projector [A] and press the height-adjuster
button [B].
The height adjuster drops down [C].
7.
8.
To lower the level of the projector , press the height-adjuster button and push down
on the top of the projector.
To adjust the angle of the picture, turn the tilt adjuster [D] right or left until desired
angle has been achieved.
– 16 –
DLP® Projector – User’s Manual
Adjusting the Zoom, Focus and Keystone
1.
2.
3.
4.
Use the Image-zoom
control (on the projector
only) to resize the
projected image and
screen size. B
Use the Image-focus
control (on the projector
only) to sharpen the
projected image A .
Press the Keystone button
on the remote control.
The keystone control
appears on the display.
Use the Keystone button
to correct image
distortion.
Adjusting the Volume
1.
2.
Press the Volume +/button on the remote
control.
The volume control
appears on the display.
Use the Volume +/button to adjust the level.
– 17 –
User’s Manual
3.
Press the Mute button to
turn off the volume. (For
remote only)
– 18 –
DLP® Projector – User’s Manual
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate
and make changes to the OSD. The following illustration shows the corresponding buttons on the
remote control and on the projector.
1. To open the OSD, press the Menu button.
2. There are six menus. Press the cursor
button to move through the menus.
3. Press the cursor
down in a menu.
button to move up and
to change values for settings, and
4. Press
then press Enter or to confirm the new
setting.
5. Press Menu to close the OSD or leave a
submenu.
Note:
Depending on the video source not all items in the OSD are available. For example, the
Horizontal/Vertical Position items in the Setup menu can only be modified when connected to a
PC. Items that are not available cannot be accessed and are grayed out.
– 19 –
User’s Manual
Setting the OSD Language
You may want to reference the OSD on your projector while reading this section. Set the OSD
language to your preference before continuing. (The default language is English.)
1. Press the Menu button. The Main menu appears.
2. Press the cursor
3. Press the cursor
4. Press the
button until Tool is highlighted.
button until Tool is highlighted.
button until your language is displayed.
5. Press the Menu button twice to close the OSD.
– 20 –
DLP® Projector – User’s Manual
Setting the OSD Language
Use the following illustration to quickly find a setting or determine the range for a setting.
– 21 –
User’s Manual
Main Menu
Press the Menu button to open the OSD menu. Press the cursor
button to move to the Main
button to move up and down in the Main menu. Press
to change
menu. Press the cursor
values for settings, and then press Enter or to confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Brightness
Press the cursor
button to adjust the brightness. (Range: 0 – 100)
50
Contrast
Press the cursor
button to adjust the contrast. (Range: 0 – 100)
50
Sharpness
Press the cursor
button to adjust the display sharpness (Range: 1-5)
3
Color
Temperature
Press the cursor
button to adjust the color temperature.
(Range: Cool/Normal/Warm)
Color
Saturation
Press the cursor
button to adjust the video saturation. (Range: 0 – 100)
50
Color Tint
Press the cursor
button to adjust the video tint/hue. (Range: 0 – 100)
50
Gamma
Press the cursor
button to adjust the gamma correction of the display.
Input
Gamma
PC
MAC
Video
Chart
B&W
2.2
1.8
2.4
2.2
2.4
Normal
Data source:
PC
Video source:
Video
Color Space
Press the cursor
button to adjust the color space.
(Range: Auto – RGB – YPbPr- YCbCr)
Reset
Resets all Main settings to default values
– 22 –
Auto
—
DLP® Projector – User’s Manual
Main Menu Functions Available for Connected Source
Function
RGB
DVI
Component Video
Composite Video
S-video
Brightness
x
x
x
x
x
Contrast
x
x
x
x
x
Sharpness
x
x
x
x
x
Color Temp
x
x
x
x
x
Color Saturation
x
x
x
Color Tint
x
x
x
Gamma
x
x
x
x
x
Color Space
x
x
x
x
x
Reset
x
x
x
x
x
x = available to video source
– 23 –
User’s Manual
Setup Menu
Press the Menu button to open the OSD menu. Press the cursor
button to move to the Setup
button to move up and down in the Setup menu. Press
to change
menu. Press the cursor
values for settings, and then press Enter or to confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Horizontal
Position
Press the cursor
button to move the image left or right. (Range: 0 – 100)
50
Vertical
Position
Press the cursor
button to move the image up or down. (Range: 0 – 100)
50
Keystone
Press the cursor
button to correct distortion of the projected image.
(Range: -50 – +50)
Aspect Ratio
Press the cursor
button to toggle between the 4:3 standard format and the
16:9 High Definition TV (HDTV) format.
4:3
Advance
Feature
See “Advance Feature” on page 25.
—
Reset
Resets Keystone and Aspect Ratio to default values
—
0
Setup Menu Functions Available for Connected Source
Function
RGB
DVI
Component Video
Composite Video
S-video
H Position
x
V Position
x
Keystone correction
x
x
x
x
x
Aspect Ratio
x
x
x
x
x
Advance Feature
x
x
x
x
x
– 24 –
DLP® Projector – User’s Manual
Function
Reset
RGB
DVI
Component Video
Composite Video
S-video
x
x
x
x
x
x = available to video source
Advance Feature
to move to the Setup menu. Press
to
Press the Menu button to open the OSD menu. Press
to move up and down in
move to the Advance Feature menu and then press Enter or . Press
the Advance Feature menu. Press
to change values for settings, and then press Enter or to
confirm the new setting.
ITEM
User Color
DESCRIPTION
DEFAULT
This feature adjusts the color balance in each color of RGB (red, green,
blue), and their neutral colors (cyan, magenta, yellow, white) by using
color correction adjustment. Increasing a color’s setting heightens the
intensity of that color on the screen, while a lower setting makes the color
less intense.
80
Press
Press
White
Peaking
to select a color.
to adjust the selected color. (Range: 0 – 100)
White Peaking increases the output in the brightest whites without
changing the blacks and dark grays. It crushes the whites slightly, but it
does not appear to clip them or seriously obscure white detail. If you
prefer a stronger image, adjust toward the maximum setting. For a
smoother, more natural image, adjust toward the minimum setting.
Press
Data source:
10
Video source:
2
to adjust the value of white peaking. (Range: 0 – 10)
Logo
Display
Press
to enable or disable if the logo displays when the projector
starts, and when no source is detected. (Range: On – Off)
Fan Speed
Press the cursor
button to toggle between normal and high fan speed
Set Fan Speed to High in altitudes over 1500 meters (5000 feet).
– 25 –
On
Normal
User’s Manual
ITEM
Security Lock
DESCRIPTION
Press the cursor
button to enable or disable Security Lock. When
you enable Security Lock a Register Password dialog box appears:
DEFAULT
—
in the
You can only use the following four cursor buttons,
password fields. Press the cursor buttons five times in any order and
confirm to set the password. When the password is enabled, it must be
entered every time after you power on the projector. See “Setting an
Access Password (Security Lock)” on page 15 for steps on setting the
password.
Audio Input
Press the cursor
channels.
button to toggle between PC and Video input
Data Source:
PC
Video source:
Video
Reset
Press Enter or
to reset advance feature settings to default values
—
Note:
If Security Lock is enabled, you must enter the password every time the projector is turned on.
However, if the projector is already turned on, Security Lock can be disabled without knowing the
current password.
– 26 –
DLP® Projector – User’s Manual
User Color
to
Press the Menu button to open the OSD menu. Press
to move to the Setup menu. Press
to move to the User
move to the Advance Feature menu and then press Enter or . Press
to move up and down to select a color. Press
Color menu and then press Enter or . Press
to change values for settings, and then press Enter or to confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Red
Green
Press the cursor
button to adjust the red color level. (Range: 0-100)
Press the cursor
button to adjust the green color level. (Range: 0-100)
80
80
Blue
Press the cursor
button to adjust the blue color level. (Range: 0-100)
80
Cyan
Press the cursor
button to adjust the cyan color level. (Range: 0-100)
80
Magenta
Press the cursor
button to adjust the magenta color level. (Range:0-100)
80
Yellow
Press the cursor
button to adjust the yellow color level. (Range: 0-100)
80
White
Press the cursor
button to adjust the white color level. (Range: 0-100)
Resets all User Color settings to default values
Reset
– 27 –
80
—
User’s Manual
Config Menu
Press the Menu button to open the Main menu. Press the cursor
button to move to the Config
button to move up and down in the Config menu. Press
to change
menu. Press the cursor
values for settings, and then press Enter or to confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Blank Screen
button to select a background color for the blank
Press the cursor
screen. (Range: Black – Red – Green – Blue – White)
Auto Source
Press the cursor
button to enable or disable automatic source
detection. (Range: On – Off)
On
Auto Power
Off
Press the cursor
button to enable or disable automatic shut-down of
lamp after 10 minutes of inactivity. (Range: On – Off)
Press the cursor
button to adjust the audio volume level. (Range: 0 - 8)
Off
Volume
Menu
Position
Menu Display
Translucent
Menu
Reset
Press the cursor
button to position the OSD on screen.
(Range: Left – Right – Center – Down – Up)
button to determine the timeout delay of the OSD.
Press the cursor
(Range: 10 – 20 sec.)
Press the cursor
button to set menu screen translucency.
(Range: 0% – 100%)
Resets all Config items to default values
Note:
The Config menu functions are available to all video sources.
– 28 –
Blue
4
Center
15
0%
DLP® Projector – User’s Manual
Utility Menu
Press the Menu button to open the Main menu. Press the cursor
button to move to the Utility
button to move up and down in the Utility menu. Press
to change
menu. Press the cursor
values for settings, and then press Enter or to confirm the new setting.
ITEM
DESCRIPTION
Video Type
Press the cursor
button to select the video standard
(Range: Auto – NTSC – PAL – SECAM)
Video AGC
Press the cursor
button to enable or disable automatic
gain control for the video source. (Range: On – Off)
Projection
Press the cursor
methods:
button to choose from four projection
DEFAULT
Auto
On
Desktop front
Desktop mount, front of screen
Desktop mount, rear of screen
Ceiling mount, front of screen
Ceiling mount, rear of screen
Frequency
Press the cursor
button to adjust the A/D sampling
clock. (Range: 0° - 180°)
Auto detected
Tracking
Press the cursor
button to adjust the A/D sampling
number. (Range: 1 - 100)
Auto detected
– 29 –
User’s Manual
ITEM
Digital Zoom
DESCRIPTION
DEFAULT
Digital operation for zoom and pan adjustment. Press
Enter or . The Zoom menu appears.
—
Press to zoom in; press to zoom out. Press Enter or
to open the Pan menu. (You must zoom in before you
can open the Pan menu.)
Use the cursor buttons to pan the zoomed image. Press the
Menu button to exit.
Reset
Resets Video Type, Video AGC, Projection, and Digital
Zoom to default values
—
Utility Menu Functions Available for Connected Source
Function
RGB
Composite Video
S-video
Video Type
x
x
Video AGC
x
x
x
x
x
x
x
x
x
x
Projection
X
Frequency
x
Tracking
x
Digital Zoom
x
Reset
x
DVI
x
Component Video
x
x
x
x = available to video source
– 30 –
DLP® Projector – User’s Manual
Tool Menu
Press the Menu button to open the Main menu. Press the cursor
button to move to the Tool
button to move up and down in the Tool menu. Press Enter or to
menu. Press the cursor
confirm the new setting.
ITEM
DESCRIPTION
DEFAULT
Language
Press the cursor
Remote control test
Follow on-screen prompts to carry out the remote control test. You are
returned to the Tool menu at the end or by pressing the Menu button.
USB test
Follow on-screen prompts to carry out the USB test. You are returned to the
Tool menu at the end or by pressing the Menu button.
Button test
Follow on-screen prompts to carry out the button test. You are returned to
the Tool menu at the end or by pressing the Menu button.
Color test
Follow on-screen prompts to carry out the color test. You are returned to the
Tool menu at the end or by pressing the Menu button.
Sound test
Follow on-screen prompts to carry out the sound test. You are returned to the
Tool menu at the end or by pressing the Menu button.
to select the desired language
– 31 –
English
User’s Manual
Status Menu
Press the Menu button to open the Main menu. Press the cursor
button to move to the Status
button to move up and down in the Status menu.
menu. Press the cursor
ITEM
DESCRIPTION
Video
Information
Displays the resolution and refresh rate for RGB/DVI mode.
Displays the color standard for video mode.
Active Source
Displays the active source.
Software
Version
Displays information about the software version.
Lamp Hours
Shows the number of hours lamp has been in use for Eco , Normal and
Boost modes.
Lamp Mode
Press the cursor
button to choose the lamp mode.
Range: Eco , Normal and Boost.
DEFAULT
These
items are
display
only.
Normal
Eco mode uses less power and extends lamp life, but decreases lamp
brightness.
Boost mode uses more power and reduces lamp life, but increases lamp
brightness.
Lamp Hour
Reset
After replacing the lamp, this item should be reset. Refer to “Replacing the
Projection Lamp” on page 36.
– 32 –
—
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
1. The lamp contains a certain amount of mercury and should be disposed of according to local
ordinance regulations.
2. Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life.
Warning:
Be sure to turn off and unplug the projector at least an hour before replacing the lamp. Failure to do
so could result in a severe burn.
Note:
Safety glasses should be worn when replacing the lamp while the projector is ceiling mounted.
1.
Loosen the two captive
screws on the lamp
compartment cover (A).
– 33 –
User’s Manual
2.
Open the lamp
compartment cover (B).
B
3.
4.
Remove the two screws
from the lamp module
(C).
Lift the module handle
up (D).
– 34 –
DLP® Projector – User’s Manual
5.
6.
Pull firmly on the
module handle to
remove the lamp module
(D)
D
Reverse steps 1 to 5 to
install the new lamp
module.
– 35 –
User’s Manual
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1.
2.
3.
4.
Press the Menu button to open the
Main menu.
Press the cursor
button to move
to the Status menu.
Press the cursor
button to move
down to Lamp Hour Reset.
Press the cursor
or Enter button.
A message screen appears.
5.
Press the cursor buttons in this order:
; ; ; .
The Status menu appears again
showing the Lamp Hours reset to
zero.
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least an hour before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
– 36 –
DLP® Projector – User’s Manual
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the
projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe
the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington
slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any
comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA94403, U.S.A. Tel: 800-5354242, http://www.Kensington.com.
– 37 –
TROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose
connection. Check the following before proceeding to the problem-specific solutions.
•
Use some other electrical device to confirm that the electrical outlet is working.
•
Ensure the projector is turned on.
•
Ensure all connections are securely attached.
•
Ensure the attached device is turned on.
•
Ensure a connected PC is not in suspend mode.
•
Ensure a connected notebook computer is configured for an external display. (This is
usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when
calling for technical support or for passing on to service personnel.
– 38 –
DLP® Projector – User’s Manual
LED Error Messages
ERROR CODE MESSAGE
POWER LED/FLASHES
READY LED/FLASHES
Lamp usage task created error
2
1
Environment usage task created error
2
2
Thermal break status error
3
0
T1 temperature over temperature
3
1
T1 sensor status fail
4
1
Lamp lit error
5
1
Ballast SCI error
5
2
Ballast UART error
5
3
Fan1 error (Lamp)
6
1
Fan2 error (Ballast)
6
2
Fan3 error (Burner)
6
3
Fan4 error (Power)
6
4
Lamp door sensor detect high
7
0
DMD error
8
0
Color wheel error
9
0
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed or upside down
Check the Projection setting on the Utility menu of the OSD.
Problem: The image is streaked
1. Set the Frequency and Tracking settings on the Utility menu of the OSD to the default
settings.
– 39 –
User’s Manual
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Main menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the Main menu of the OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Press the power button twice to turn off the
projector. When the Ready LED is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
– 40 –
SPECIFICATIONS
Input/output connectors
Data in
PR3010
PR3020
PR5020
×
×
DVI-D
RGB HD-15
Data out
RGB HD-15
Video
composite video (RCAx1)
S-video
Audio in
Stereo RCAx2 (L+R)
Stereo Mini-jack
Audio out
Control
Stereo Mini-jack
×
×
USB
Security
Kensington lock
– 41 –
RS-232
User’s Manual
Projection Distance V.S. Projection Size
C
D
A
B
L Projection Distance
PR3020 and PR3010 Projection distance and size table
Max. Screen Size
(Wide)
Projection
Distance L
Diagonal
Width
A
1.8
Height
C
Max. Screen Size
(Tele)
Diagonal
Width
B
2.1
Height
D
1.00 m
0.66 m
0.53 m
0.40 m
0.57 m
0.46 m
0.34 m
3.28 '
26.04 ''
20.83 ''
15.62 ''
22.57 ''
18.06 ''
13.54 ''
1.50 m
0.99 m
0.79 m
0.60 m
0.86 m
0.69 m
0.52 m
4.92 '
39.06 ''
31.25 ''
23.43 ''
33.86 ''
27.09 ''
20.32 ''
2.40 m
1.59 m
1.27 m
0.95 m
1.38 m
1.10 m
0.83 m
7.87 '
62.49 ''
49.99 ''
37.50 ''
54.18 ''
43.34 ''
32.51 ''
2.80 m
1.85 m
1.48 m
1.11 m
1.61 m
1.28 m
0.96 m
9.18 '
72.91 ''
58.33 ''
43.74 ''
63.21 ''
50.57 ''
37.93 ''
3.20 m
2.12 m
1.69 m
1.27 m
1.83 m
1.47 m
1.10 m
10.50 '
83.32 ''
66.66 ''
49.99 ''
72.24 ''
57.79 ''
43.34 ''
3.60 m
2.38 m
1.90 m
1.43 m
2.06 m
1.65 m
1.24 m
11.81 '
93.74 ''
74.99 ''
56.24 ''
81.27 ''
65.01 ''
48.76 ''
4.00 m
2.65 m
2.12 m
1.59 m
2.29 m
1.83 m
1.38 m
13.12 '
104.15 ''
83.32 ''
62.49 ''
90.30 ''
72.24 ''
54.18 ''
4.40 m
2.91 m
2.33 m
1.75 m
2.52 m
2.02 m
1.51 m
14.43 '
114.57 ''
91.66 ''
68.74 ''
99.33 ''
79.46 ''
59.60 ''
4.80 m
3.17 m
2.54 m
1.90 m
2.75 m
2.20 m
1.65 m
15.74 '
124.98 ''
99.99 ''
74.99 ''
108.36 ''
86.69 ''
65.01 ''
5.20 m
3.44 m
2.75 m
2.06 m
2.98 m
2.39 m
1.79 m
17.06 '
135.40 ''
108.32 ''
81.24 ''
117.39 ''
93.91 ''
70.43 ''
5.60 m
3.70 m
2.96 m
2.22 m
3.21 m
2.57 m
1.93 m
18.37 '
145.82 ''
116.65 ''
87.49 ''
126.42 ''
101.13 ''
75.85 ''
7.00 m
4.63 m
3.70 m
2.78 m
4.01 m
3.21 m
2.41 m
– 42 –
DLP® Projector – User’s Manual
22.96 '
182.27 ''
145.82 ''
109.36 ''
158.02 ''
126.42 ''
94.81 ''
10.00 m
6.61 m
5.29 m
3.97 m
5.73 m
4.59 m
3.44 m
32.80 '
260.38 ''
208.31 ''
156.23 ''
225.75 ''
180.60 ''
135.45 ''
PR5020 Projection distance and size table
Max. Screen Size
(Wide)
Projection
Distance L
Diagonal
Width
A
1.8
Height
C
Max. Screen Size
(Tele)
Diagonal
Width
B
2.1
Height
D
1.00 m
0.69 m
0.56 m
0.42 m
0.60 m
0.48 m
0.36 m
3.28 '
27.34 ''
21.87 ''
16.40 ''
23.43 ''
18.75 ''
14.06 ''
1.50 m
1.04 m
0.83 m
0.63 m
0.89 m
0.71 m
0.54 m
4.92 '
41.01 ''
32.81 ''
24.61 ''
35.15 ''
28.12 ''
21.09 ''
2.40 m
1.67 m
1.33 m
1.00 m
1.43 m
1.14 m
0.86 m
7.87 '
65.62 ''
52.49 ''
39.37 ''
56.24 ''
44.99 ''
33.75 ''
2.80 m
1.94 m
1.56 m
1.17 m
1.67 m
1.33 m
1.00 m
9.18 '
76.55 ''
61.24 ''
45.93 ''
65.62 ''
52.49 ''
39.37 ''
3.20 m
2.22 m
1.78 m
1.33 m
1.90 m
1.52 m
1.14 m
10.50 '
87.49 ''
69.99 ''
52.49 ''
74.99 ''
59.99 ''
44.99 ''
3.60 m
2.50 m
2.00 m
1.50 m
2.14 m
1.71 m
1.29 m
11.81 '
98.43 ''
78.74 ''
59.06 ''
84.36 ''
67.49 ''
50.62 ''
4.00 m
2.78 m
2.22 m
1.67 m
2.38 m
1.90 m
1.43 m
13.12 '
109.36 ''
87.49 ''
65.62 ''
93.74 ''
74.99 ''
56.24 ''
4.40 m
3.06 m
2.44 m
1.83 m
2.62 m
2.10 m
1.57 m
14.43 '
120.30 ''
96.24 ''
72.18 ''
103.11 ''
82.49 ''
61.87 ''
4.80 m
3.33 m
2.67 m
2.00 m
2.86 m
2.29 m
1.71 m
15.74 '
131.23 ''
104.99 ''
78.74 ''
112.49 ''
89.99 ''
67.49 ''
5.20 m
3.61 m
2.89 m
2.17 m
3.10 m
2.48 m
1.86 m
17.06 '
142.17 ''
113.74 ''
85.30 ''
121.86 ''
97.49 ''
73.12 ''
5.60 m
3.89 m
3.11 m
2.33 m
3.33 m
2.67 m
2.00 m
18.37 '
153.11 ''
122.48 ''
91.86 ''
131.23 ''
104.99 ''
78.74 ''
7.00 m
4.86 m
3.89 m
2.92 m
4.17 m
3.33 m
2.50 m
22.96 '
191.38 ''
153.11 ''
114.83 ''
164.04 ''
131.23 ''
98.43 ''
10.00 m
6.94 m
5.56 m
4.17 m
5.95 m
4.76 m
3.57 m
32.80 '
273.40 ''
218.72 ''
164.04 ''
234.35 ''
187.48 ''
140.61 ''
Shaded rows are equivalent measurement in feet and inches
– 43 –
User’s Manual
Timing Mode Table
The projector can display several resolutions. The following table outlines the resolutions that can be
displayed by the projector.
Signal
Resolution
NTSC
Frequency H. Frequency V.
Video
Digital
Analog
60.0
Ο
-
-
15.625
50.0
Ο
-
-
640 x 350
37.9
85.1
-
Ο
Ο
720 x 400
31.5
70.0
-
Ο
Ο
720 x 400
37.9
85.0
-
Ο
Ο
640 x 480
31.5
60.0
-
Ο
Ο
640 x 480
37.9
72.8
-
Ο
Ο
640 x 480
37.5
75.0
-
Ο
Ο
640 x 480
43.3
85.0
-
Ο
Ο
800 x 600
37.9
60.3
-
Ο
Ο
800 x 600
46.9
75.0
-
Ο
Ο
800 x 600
48.1
72.2
-
Ο
Ο
800 x 600
53.7
85.1
-
Ο
Ο
1024 x 768
48.4
60.0
-
Ο
Ο
1024 x 768
56.5
70.1
-
Ο
Ο
1024 x 768
60.0
75.0
-
Ο
Ο
1024 x 768
68.7
85.0
-
Ο
Ο
1280 x 1024
64.0
60.0
-
Ο
Ο
1600 x 1200**
75.0
60.0
-
-
Ο
640 x 480
35.0
66.7
-
Ο
Ο
832 x 624
49.7
74.5
-
Ο
Ο
1024 x 768
60.2
74.9
-
Ο
Ο
1152 x 870
68.7
75.1
-
Ο
Ο
480i
31.5
30.0
-
-
-
576i
31.3
25.0
-
-
-
480p
31.5
60.0
-
-
-
576p
31.3
50.0
-
-
-
720p
45.0
60.0
-
-
-
(KHz)
(Hz)
-
15.734
PAL/SECAM
-
VESA
Apple Macintosh
SDTV
HDTV
Ο: Frequency supported - : Frequency not supported
The native resolution for the PR5020 and PR3020 is 1024 x 768. The native resolution for the PR3010
is 800 x 600. Resolution other than native mode may be displayed with uneven size of text or lines.
UXGA resolution with half-sampling
Digital Timing is only for PR5020
– 44 –
DLP® Projector – User’s Manual
Projector Dimensions
300 mm (11.8”)
96 mm (3.8”)
244 mm (9.6”)
– 45 –
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC Class B, UL, C-UL, CE, CB, TUV-GS, CCC , ICES-003(Class B)
EN 55022 Warning
This is a Class B product. In a domestic environment, it may cause radio interference, in which case
the user may be required to take adequate measures. The typical use is in a conference room,
meeting room, or auditorium.
– 46 –
DLP® Projector – User’s Manual
Planar System, Inc.
Customer Service
Online Support: http://www.planar.com/support
E-mail: PlanarSupport@planar.com
Tel: US/Canada 1-866-PLANAR-1 (1-866-752-6271 or 1-503-748-5953), Europe +358 9 420 01
Hours: M-F, 8am-8pm Eastern Time, or 8am-4pm EET
© 2006 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc.
Other brands and names are the property of their respective owners.
Technical information in this document is subject to change without notice
– 47 –