Digital Watchdog D2367WTIR User manual

Infinity D2367WTIR
User Manual Version #2:
Camera with ICON Menu
11192010
PRECAUTIONS














Do not open or modify.
Do not open the case except during maintenance and installation, for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to Provide reasonable protection against harmful interference .when the equipment is operated in a residential environment. This equipment
generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance
with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacture.
TROUBSHOOTING
Before sending your camera for repair, check the following or contact our technical specialist.
No VIDEO
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Out-of-Focus VIDEO
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.
FEATURES
1/3” Sony Super HAD II CCD
High Resolution 560 TV Lines
3.3 ~ 12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
True Day & Night / TDN5 (Electro Magnetic Mechanism)
Star-Light (Super Low Light Technology)
Max-DR (Electronic Wide Dynamic Range)
Enables the camera to capture perfect images in both bright and dark environments simultaneously.
3D-DNR (3D Digital Noise Reduction)
Produces less noise and more color during low-light application.
HME (Highlight Mask Exposure)
Masks overly exposed light to produce a true video image of any environment.
SLC (Side Light Compensation)
DIS (Digital Image Stabilizer)
Programmable Privacy Zone (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
No Fog or Condensation under Any Weather Condition
DIMENSIONS (mm) & POWER REQUIREMENT
POWER REQUIREMENT:
12VDC @1A
24VAC @ .500mA
Power Wire Maximum Distance
Wire Gauge
24 AWG
22 AWG
20 AWG
18 AWG
16 AWG
14 AWG
12 AWG
10 AWG
12VDC
80ft
128ft
203ft
323ft
514ft
816ft
1295ft
2057ft
24VAC
323ft
513ft
815ft
1295ft
2056ft
3264ft
5183ft
8228ft
COAXIAL CABLE TYPE
MAXIMUM DISTANCE
RG59/ U
RG6/U
RG11/U
750feet
1,000feet
1,500feet
INSTALLATION
Included with DW Indoor Dome Camera:
1
3
4
1.
2.
3.
4.
5.
6.
User Manual
Mounting Template
Security L-Key
Single Sided Hex Key
Secondary BNC Cable for a Field Monitor
Four (4) Screws and Four (4) Dry Wall
Anchors
5
2
6
Camera Installation
Use the mounting template to mount the camera.
Using the security L-key to loosen the four screws that secure the
vandal proof dome cover, Remove the vandal proof dome cover to
access the screw holes to mount the camera.
NOTE: Keep the lens and the vandal proof cover free from dust or
fingerprint.
CONNECTION
DC12V / AC24V
Video Output
BNC Cable
Main Monitor
Spot Monitor Cable
Field Test Monitor
CAMERA SETTINGS & ON-SCREEN DISPLAY
1. Adjusting Level Volume (VR)
If the entire image is too dark or bright or the
backlight compensation is not correct even after
the lens is set to “DC,” you need to adjust the level
volume.
2. Second Video Out Connector (2nd Video)
If installer uses a portable monitor, this connector
should be connected.
2nd Video
On-Screen Display
Joy Stick Key
VR
EXPOSURE
LENS
DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
SHUTTER
1/160 /1/100 / FLC / 1/250 ~ 10000 / SENS-UP x2 ~ x250
BLC
OFF / ON
BLC (Back Light Compensation)
AGC
HIGH / MIDDLE / LOW / OFF
AGC (Auto Gain Control)
MAX-DR
OFF / ON (0 ~ 20) (Electronic Wide Dynamic Range)
STAR-LIGHT
AUTO (x2 ~ x250) / OFF (x32 is recommended.)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY RESET
COLOR
WB MODE
AWC / ATW / MANUAL / PUSH LOCK
R-Y GAIN
0 ~ 100
B-Y GAIN
0 ~ 100
DAY & NIGHT
AUTO / COLOR / BW / EX-CONT
Day & Night Mode
COLOR ---- BW : Switching from color to BW; if the number is higher, the camera will only switch during a super low light condition.
BW ---- COLOR : Switching from BW to color; this number should always be lower than COLOR to BW
Read Time: Time interval to switch from Color to Black-and-White
COLOR
B&W: (BURST:OFF/ON) When the burst is OFF will make less noise
C-SUP
Color Suppression :Color will be reduced at low illumination, if the C-SUP Level is higher.
0 ~ 100 (Not Available when DNR is On.)
A-SUP
Aperture Suppression: The sharpness of the edges will be reduced at low illumination, if A-SUP Level is higher.
0 ~ 100 (Not Available when DNR is On.)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
FUNCTION
MIRROR
OFF / MIRROR / V-FLIP / ROTATE
SHARPNESS
0 ~ 31
GAMMA
0.05 ~ 1.00 / USER
FREEZE
OFF / ON
NEGATIVE
OFF/ ON
3D-DNR
OFF / LOW / MIDDLE / HIGH
3D-DNR (3D Digital Noise Reduction)
D-ZOOM
OFF / ON (x1.0 ~ x32 PTZ)
SLC
OFF / ON
SLC (Side Light Compensation)
HME
OFF / ON
HME (Highlight Masking Exposure)
DIS
OFF / ON
DIS (Digital Image Stabilizer)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
MOTION
(OMNI-Focus Lens Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15)
Motion Alarm Zoom-In Delay
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
SETUP
CAMERA ID
0 ~ 255
TITLE
OFF / ON
DPC
OFF / AUTO
DPC (Dead Pixels Cancellation)
MONITOR
CRT / LCD
LANGUAGE
English, Japanese, Chinese
BAUDRATE
2400 / 4800 / 9600 / 14400 / 19200 / 38400.
Protocol is Pelco-D (fixed cannot be changed; hardcoded into the DSP)
OMNI LENS
OFF / 1 ~ 10 (for OMNI-PLUS CAMERA only)
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC
INTERNAL / AUTO
V-PHASE
0 ~ 199
EXIT JUMP
EXIT / SAVE & EXIT / FACTORY SET
EXIT
EXIT
Exit the menu
SAVE&EXIT
Exit the menu and save the setting
FACTORY SET
Reset the menu setting to factory default
SPECIFICATIONS:
Camera TYPE
Image
Scanning
Min. Scene Illumination
Functions
5436 W Crenshaw St. Tampa, FL 33634
Tel: 866-446-3595 / 813-888-9555
Fax: 813-888-9262
www.Digital-Watchdog.com
technicalsupport@dwcc.tv
Technical Support Hours: Monday-Friday
8:30am to 8:00pm Eastern Time
Color / BW
D2367WTIR
Mount
Surface
Device
Super HAD II CCD
Size
1/3"
Pixels-Total
811(H) x 508 (V)
Pixels-Effective
768(H) x 494 (V)
System
525 line, 2:1Interlace
Horizontal Frequency Internal Mode
15,734Hz
Vertical Frequency Internal Mode
59.94Hz
IR LED On
0.0 Lux
IR Distance
100ft Range
BLC
ON / OFF
AGC
HIGH / MIDDLE / LOW /OFF
MAX-DR
OFF / ON
Mirror
OFF / MIRROR / V-FLIP / ROTATE
STAR-LIGHT
AUTO (x2 ~ x250) / OFF
3D-DNR
OFF / ON
SLC
OFF / ON
HME
OFF / ON
DIS
OFF / ON
Privacy Zone
6 Programmable Zone / Size
Lens
Focal Length
3.3~12mm Varifocal Auto Iris Lens
Resolution
Horizontal
560 TV Lines [Color]; 580 TV Lines [BW]
Video Output
VBS 1.0Vp-p
VBS 1.0Vp-p(75 Load)
S/N Ratio
S/N Ratio
50dB
OSD
OSD
YES
Environmental Conditions
Operating Temperature
-10℃ ~ +55℃(14℉ ~ 131℉)
Humidity
Less than 90%
Power Requirement
12VDC / 24VAC
Power Consumption
1.8[W] / 2.4 [W] LED Off; 4.6[W] / 4.9[W] LED On
Power