Alliance Laundry Systems SCU020JLF Instruction manual

Programming
Washer-Extractor
Refer to Page 4 for Model Numbers
CHM1773C
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
www.comlaundry.com
Part No. F8238301R2
April 2012
WARNING
Failure to install, maintain, and/or operate
this machine according to the
manufacturer's instructions may result in
conditions which can produce bodily injury
and/or property damage.
W030
F8238301
NOTE: The WARNING and IMPORTANT
instructions appearing in this manual are not meant
to cover all possible conditions and situations that
may occur. It must be understood that common
sense, caution, and carefulness are factors which
cannot be built into these machines. These factors
MUST BE supplied by the person(s) installing,
maintaining, or operating the machine.
Always contact the distributor, service agent, or the
manufacturer about any problems or conditions you do
not understand.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Table of
Contents
Model Identification ...........................................................................
Preliminary Information....................................................................
About the Control .................................................................................
Glossary of Terms.................................................................................
Power Failure Recovery .......................................................................
Communications ...................................................................................
Control Identification.........................................................................
Select Cycle Pads..................................................................................
Display Identification .........................................................................
Light Emitting Diodes (LEDs) .............................................................
Machine Operation.............................................................................
Start Up.................................................................................................
Ready Mode..........................................................................................
Partial Vend Mode................................................................................
Additional Vend Mode .........................................................................
Start Mode ............................................................................................
Door Locking Mode .............................................................................
Run Mode .............................................................................................
End of Cycle Mode...............................................................................
Cycle Sequence.....................................................................................
Door Unlocking Mode..........................................................................
Signals...................................................................................................
Changing Cycles...................................................................................
Special Features ..................................................................................
Programming Control ...........................................................................
Collecting Audit Information ...............................................................
Testing Machine and Control Functions...............................................
Rapid Advance Feature.........................................................................
Clearing the Vend Feature ....................................................................
Communications Mode.........................................................................
Coin Drop .............................................................................................
Start Pulse Operation ............................................................................
Top Cover and Coin Vault Openings ...................................................
Special Vend.........................................................................................
OPL Mode ............................................................................................
Opening the Top Cover ......................................................................
Entering the Manual Mode................................................................
How to Enter the Manual Mode ...........................................................
Programming Control ........................................................................
What Can Be Programmed? .................................................................
Programmable Options Available.........................................................
Programming Flowcharts......................................................................
1. Normal/90C Vend Price “AtS1”..................................................
2. Coin #1 Value “dEn1” .................................................................
3. Coin #2 Value “dEn2” .................................................................
4. Start Pulse Value “PLSE” ............................................................
5. Start Pulse Mode “PLSn”.............................................................
6. Available Type “AtyP” ................................................................
7. Default Cycle “dCYC” ................................................................
8. OPL Mode Enable/Disable“oPL” ................................................
9. Audio Signal “AUd” ....................................................................
10. Card Reader Display Control “CArd” .........................................
4
5
5
5
5
5
6
6
7
7
8
8
8
8
8
8
8
8
8
8
8
9
9
10
10
10
10
10
10
10
10
10
11
11
11
12
13
13
14
14
14
19
26
27
28
29
30
31
32
33
34
36
© Copyright 2012, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
2
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
11. Error Code Programming “Err-”.................................................. 37
12. Cycle Programming “CyC-” ........................................................ 41
13. Supply/Compartment Dispenser Programming “SUPC”
(Design 1 Models Only)............................................................... 47
14. Number of Balance Retries “bALr”
(Variable Frequency Drives Only)............................................... 47
15. IR Access (Enabled/Disabled) “IrA” ........................................... 48
16. Fahrenheit/Celsius “t FC” (Models with Heat)............................ 48
17. Hot Water Temperature “FH”...................................................... 49
18. Warm Water Temperature “FHC” ............................................... 49
19. Cold Water Temperature “FC” .................................................... 50
20. Cooldown Enable/Temperature “Codn” (Models with Heat)...... 50
21. Production Test Cycle (Enabled/Disabled) “PtEn” ..................... 51
22. Manual Rapid Advance (Enabled/Disabled) “rAEn” .................. 51
23. No Cycle Time Display “nCtd” ................................................... 52
24. Programmable Cycle Time Display “PCtd” ................................ 52
25. Slow Drain Detection Adjust Value “SdAd”............................... 53
26. Pause/Resume Mode (Enabled/Disabled) “SPAU” ..................... 53
27. Normal/60C Vend Price “AtS2”.................................................. 54
28. Normal/40C Vend Price “AtS3”.................................................. 55
29. Perm Press/90C Vend Price “AtS4” ............................................ 56
30. Perm Press/60C Vend Price “AtS5” ............................................ 57
31. Perm Press/40C Vend Price “AtS6” ............................................ 58
32. Perm Press/70C Vend Price “AtS7” ............................................ 59
33. Perm Press/50C Vend Price “AtS8” ............................................ 60
34. Delicate/30C Vend Price “AtS9”................................................. 61
35. Set Real-Time Clock “rtC-”......................................................... 62
36. Special Vend A Data “SPA-” ...................................................... 63
37. Low Water Level “FLo” .............................................................. 82
38. Medium Water Level “FnEd” ...................................................... 82
39. High Water Level “FHI”.............................................................. 83
40. Auto-Water Leak Detection “ALd-”............................................ 83
Collecting Audit Information ............................................................ 85
Manual Reset....................................................................................... 86
Testing Machine and
Electronic Control Functions............................................................. 87
Production Test Cycle........................................................................... 89
Error Codes......................................................................................... 92
Rapid Advance Feature...................................................................... 96
Clear Vend Feature ............................................................................ 97
Power Fail Recovery........................................................................... 98
Communications Mode ...................................................................... 99
Infra-red Communications.................................................................... 99
Card Reader Communications (Card Models Only) ............................ 99
Default Cycles...................................................................................... 100
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Model Identification
Information in this manual is applicable to these
machine models:
HCD020JD2
SCL030JC2
SCL040JC2
SCL060JC2
SCU080JCF
SCL020JC2
SCL030JCF
SCL040JD2
SCL060JCF
SCU080JCV
SCL020JD2
SCL030JD2
SCL040JDF
SCL060JD2
SCU080JDF
SCL020JDF
SCL030JDF
SCL040JE2
SCL060JE2
SCU080JDV
SCL020JE2
SCL030JE2
SCL040JEF
SCL060JXF
SCU080JEF
SCL020JEF
SCL030JEF
SCL040JX2
SCU060JC2
SCU080JEV
SCL020JX2
SCL030JX2
SCL040JXF
SCU060JCF
SCU080JLF
SCU020JC2
SCL030JXF
SCL040JXV
SCU060JCV
SCU080JLV
SCU020JCF
SCL030JY2
SCU040JC2
SCU060JD2
SCU080JXF
SCU020JCV
SCU030JC2
SCU040JCF
SCU060JDF
SCU080JXV
SCU020JD2
SCU030JCF
SCU040JCV
SCU060JDV
SCU080JYF
SCU020JDF
SCU030JCV
SCU040JD2
SCU060JE2
SCU080JYV
SCU020JDV
SCU030JD2
SCU040JDF
SCU060JEF
SCU020JE2
SCU030JDF
SCU040JDV
SCU060JEV
SCU020JEF
SCU030JDV
SCU040JE2
SCU060JL2
SCU020JEV
SCU030JE2
SCU040JEF
SCU060JLF
SCU020JL2
SCU030JEF
SCU040JEV
SCU060JLV
SCU020JLF
SCU030JEV
SCU040JL2
SCU060JX2
SCU020JLV
SCU030JL2
SCU040JLF
SCU060JXF
SCU020JX2
SCU030JLF
SCU040JLV
SCU060JXV
SCU020JXF
SCU030JLV
SCU040JX2
SCU060JY2
SCU020JXV
SCU030JX2
SCU040JXF
SCU060JYF
SCU020JY2
SCU030JXF
SCU040JXV
SCU060JYV
SCU020JYF
SCU030JXV
SCU040JY2
SCU020JYV
SCU030JY2
SCU040JYF
SCU030JYF
SCU040JYV
SCU030JYV
4
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Preliminary Information
About the Control
Communications
This control is an advanced, programmable computer
that lets the owner control most machine features by
pressing a sequence of keypads. Refer to Figure 1.
The control may be programmed manually or by infrared communication with an external device. A limited
number of features can be programmed by a card reader.
The control allows the owner to program custom
cycles, set vend prices, retrieve audit information,
program special vend features and other
programmable features. Refer to Programming
Control for a list of features. Machines shipped from
the factory have a default cycle and wash temperature
setting of PERM PRESS/60C built in. However, the
owner can change the default cycle, or any cycle, as
needs permit.
Infra-red Communications
IMPORTANT: In the event of a power failure, the
control will not have to be reprogrammed. It is
designed with a memory system that will remember
how it was programmed until the electrical power
is restored.
IMPORTANT: It is extremely important that the
machine has a good ground connection and that all
mechanical and electrical connections to the control
are made before applying power to or operating the
machine.
Glossary of Terms
The following are a few terms and abbreviations to
learn. These are referred to throughout the instructions.
An external device, such as a PDA, allows the owner
to program and retrieve information from the control
without touching the keypad. An external device
greatly expands the programming options available to
the owner. However, it is not required to program and
operate the machine. The operation of an external
device and the advanced features available are covered
separately in the instructions included with the
external device software. Contact Alliance Laundry
Systems for a list of approved PDAs and other external
devices.
Serial Card Reader Communications (Card
Models Only)
The control will accept communication with a serial
card reader in order to perform vending transactions
when a card is inserted to pay for cycles. The card
reader can also allow the owner to program a limited
number of features and collect audit information.
For detailed information on the serial card reader
communications, refer to instructions included with
the card reader.
Display - This term refers to the window area of the
control that displays words and values.
LED (Light Emitting Diode) - This term refers to the
lights next to the keypads and status words of
the control.
Power Failure Recovery
If a cycle is in progress and the power fails, the cycle
status is saved in memory. When the power recovers,
the machine will resume into the previously active
cycle automatically without user input if the length of
the power failure was less than two minutes.
If the length of the power failure is greater than two
minutes, the control will return to Start Mode and the
cycle step where the power failure occured. User must
press START pad to resume the cycle.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Control Identification
Select Cycle Pads
Refer to Figure 1.
Select Cycle pads are used to select the specific
machine cycle. These pads include NORMAL/90C,
NORMAL/60C, NORMAL/40C, PERM PRESS/90C,
PERM PRESS/60C, PERM PRESS/40C, PERM
PRESS/70C, PERM PRESS/50C and DELICATE/
30C. These pads allow the user to select a cycle other
than the default cycle (PERM PRESS/60C). The
Select Cycle keypads are not active after the first fill
step of the cycle. The selected cycle is indicated by the
light (LED) on the pad. Pressing the flashing START
pad will confirm the selection and the cycle will begin.
When the card reader is used, pressing the START pad
will start the cycle and deduct the vend price from the
card.
2
1
4
3
6
5
9
8
7
14
12
13
11
10
CHM1773C
CHM1773C
1
LED Status Lights
8
PERM PRESS/40C
2
Display
9
START (enter) Pad
3
Four 7-Segment Digits
10
DELICATE/30C
4
NORMAL/90C
11
PERM PRESS/60C
5
NORMAL/60C
12
PERM PRESS/50C
6
NORMAL/40C
13
PERM PRESS/70C
7
PERM PRESS/90C
14
LED Light
Figure 1
6
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Display Identification
Light Emitting Diodes (LEDs)
Spin LED
Refer to Figure 1.
Spin LED is lit during the Final Spin portion of the
cycle.
Light Emitting Diodes (LEDs) are used to indicate the
chosen cycle, cycle status, if vend is needed, when the
bleach compartment is dispensing, and door lock
information. See below for information on each LED.
Cycle LED (NORMAL/90C, NORMAL/60C,
NORMAL/40C, PERM PRESS/90C, PERM
PRESS/60C, PERM PRESS/40C, PERM
PRESS/70C, PERM PRESS/50C and
DELICATE/30C)
Cycle LED will remain lit the entire cycle.
Wash LED
Wash LED is lit at the beginning of a wash portion of
the cycle and will remain lit until the wash is
complete.
Door LED
Door LED is lit whenever the door is locked. The door
can’t be opened when this LED is lit.
Bleach LED
Bleach LED is lit when bleach compartment is
dispensing for the first time in the cycle.
Four 7-Segment Digits
The 7-Segment Digits are used to display the time
remaining in a cycle, vend price, error messages and
descriptive codes. During diagnostic testing or manual
programming of the control, these digits will display
descriptive codes and values (as described in Entering
the Manual Mode).
Rinse LED
Rinse LED is lit at the beginning of a rinse portion of
the cycle and will remain lit until the rinse is complete.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Machine Operation
Start Up
When power is applied to the machine, the control will
display its software version as “S xx” (“xx” is the
version number) for one second. If the control was not
powered down during a running cycle, it will enter
Ready Mode, Partial Vend Mode or Start Mode.
Ready Mode
In this mode of operation the control indicates the
current selected cycle by lighting the LEDs. The full
current vend price for the cycle appears in the display.
To start the cycle, the user must satisfy the vend price
and then press the START keypad.
The user will be able to select a different cycle by
pressing a cycle pad when the machine is in Ready
Mode.
Partial Vend Mode
The control enters this mode when part of the vend
price has been entered, but not enough vend is entered
to satisfy the vend price. The control will display the
remaining vend price needed to start the cycle.
The user will be able to select a different cycle by
pressing a cycle pad when the machine is in Partial
Vend Mode.
Additional Vend Mode
The control enters this mode if a higher priced cycle is
selected while the machine is in Start Mode or Run
Mode, but before the first fill has completed. If the
vend price is not satisfied within one (1) minute, the
control will go back to the first selection and the cycle
will continue if it was paused. After the first fill, all
key presses will be ignored, allowing the machine to
go through the complete cycle.
After pressing the START keypad, the door will lock
and the cycle will begin.
Door Locking Mode
The control enters this mode after the START (enter)
keypad is pressed in Start Mode. The control stays in
Door Locking Mode until it confirms the door is
closed and locked.
Run Mode
The control enters this mode when a cycle is running.
The time remaining appears in the display, the status
LEDs are lit and the loading door is locked.
End of Cycle Mode
When a cycle is complete, the control will display “00”
until the machine door is opened, a key is pressed, or a
coin/card is entered. The display will revert back to Ready
Mode if door is opened or keypad is pressed. If vend is
entered, the control will change to Partial Vend Mode or
Start Mode.
Cycle Sequence
Upon the start of a cycle, the control will display the
total cycle time. The appropriate LEDs will light while
the machine passes through different cycle steps. Any
coin entered after the first fill cycle has been started
will be added to the total coin counter, but the user will
not be able to change cycles or water temperature.
Door Unlocking Mode
The control enters this mode after cycle has ended. The
control waits for confirmation that door is unlocked.
Once confirmation is received that door is unlocked,
control will enter End of Cycle Mode.
Start Mode
The control enters this mode when the full vend price
is satisfied, the vend price is zero, the control is in
OPL Mode. The START pad LED will flash one (1)
second on and one (1) second off. If Start Mode is
entered because the vend price is satisfied or the
control is in OPL Mode, the display will show
“PUSH” for one (1) second, “Strt” for one (1) second
and the current cycle time for one (1) second. If Start
Mode is entered because the vend price is zero, the
display will show “FREE”. When first entering Start
Mode, a signal will sound for one (1) second on and
one (1) second off for 10 seconds if Signal for Start is
enabled.
8
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Machine Operation
Signals
Changing Cycles
There are five options when a signal can be used during
the machine operation. These five options are listed
below:
1. End of Cycle Signal
By default, this signal is turned off. If turned on, the
signal sounds for three (3) seconds at the end of a
cycle.
2. Signal On Keypad Depression
By default, this signal is turned on and sounds for
a quarter of a second each time a keypad is pressed.
3. Signal On Coin Input/Card Insertion
By default, this signal is turned on and will sound
for a quarter of a second each time a coin or card
is entered.
4. Signal for Card Removal (Card Models Only)
By default, this signal is turned on and will sound
one (1) second on and one (1) second off when
the control is prompting for card removal.
5. Signal for Start
By default, this signal is turned on and will sound
one (1) second on and one (1) second off for 10
seconds after vend price has been satisfied.
NOTE: Refer to Programming Control to program
signal options.
Cycles can be changed anytime during the first Fill
step. After the first Fill step, all key presses are
ignored.
F8238301
Selecting a higher priced cycle will pause the first Fill
step, and the Vend Price will flash one (1) second on and
one (1) second off until the vend price has been satisfied.
After the vend price has been satisfied, the cycle will
continue with the new selections. If the vend price is not
satisfied within one minute, the machine control will go
back to the previously set cycle.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Special Features
Programming Control
Rapid Advance Feature
The control allows the machine owner to program the
control with the use of the keypad. Cycle and vend
options may be programmed, audit information may
be viewed and diagnostic tests may be run by pressing
combinations of the Select Cycle keypads.
This feature allows the user to quickly advance
through active cycles or advance into a cycle from
Ready Mode. This feature is useful when tests must be
performed immediately on a machine currently in an
active cycle. In this case, the user can quickly advance
through the cycles to the shake out step, then End of
Cycle Mode. At this point, the user can perform the
required tests and then return the machine to the point
it was interrupted.
For details on programming Select Cycle and vend
options, refer to Programming Control.
Collecting Audit Information
The control will store audit information in its memory
that can be retrieved by pressing various combinations
of Select Cycle keypads. The control will record coins
entered, total machine cycles, total start pulses and
total rapid advance cycles.
For more information on the audit features, refer to
Collecting Audit Information.
NOTE: Additional audit information is retrievable
with an external device and the card reader. Refer
to the appropriate instruction manual.
Testing Machine and Control
Functions
Special diagnostic features built into the control allow
the owner to run specific diagnostic tests. By opening
and closing the top cover and then pressing various
sequences of Select Cycle, Select Wash Temperature
and Soil keypads, the owner may retrieve or perform
the following tests:
• Balance Weight Test (Design 1 models only)
• Drive DC Bus Display Test (Design 2 models
only)
• Water Purge Test
• Water Leak Detection Test
• Drive Software Version Number (Design 2
models only)
• Drive Parameter Table Version Number (Design
2 models only)
• Drive Type (Design 2 models only)
For detailed information on running diagnostic tests,
refer to Testing Machine and Control Functions.
10
For detailed information on using the Rapid Advance
feature, refer to Rapid Advance Feature.
Clearing the Vend Feature
This feature allows the user to return the control back
to Ready Mode if coins have been entered but the full
vend price has not yet been satisfied.
For more information on using the Clear Vend feature,
refer to Clear Vend Feature.
Communications Mode
This feature allows the control to communicate with
an external device or the card reader. This allows the
control to be programmed and have its data read
without using the keypad.
For more detailed information on using the
Communications Mode feature, refer to
Communications Mode.
Coin Drop
The control will accept pulses from a single or dual
coin drop to satisfy vend price. Each coin drop will
have the ability to start a cycle.
Start Pulse Operation
The control will accept pulses from optional payment
systems. The machine can be programmed to receive a
single start pulse or multiple start pulses, or the Start
Pulse Option can be turned off. The Start Pulse Mode
allows the machine to go from Ready Mode to the
Start Mode after a single pulse or multiple pulses are
received.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Special Features
Top Cover and Coin Vault Openings
The control will capture the times and dates of the
openings of the Coin Vault and the Top Cover. The
information is saved in memory. An open top cover
combined with various keypad presses allows the
control to enter manual modes of operation. These
modes include Manual Programming, Audit Collection
and Diagnostics.
Special Vend
This feature allows the owner to program the control
to allow programmable vend prices for specific hours
and dates.
For details on programming Special Vend, refer to
Programming Control.
OPL Mode
This feature allows the user to start a cycle without
satisfying the vend price.
For details on enabling OPL Mode, refer to
Programming Control.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Opening the Top Cover
To manually program the control, the top cover must
be opened. Opening and closing the top cover trips a
switch which allows access to various programming
options. Once opened, the top cover may either be left
open, and then closed after programming, or it may be
closed immediately.
The top cover is located on the top of the machine.
1. Unlock top cover.
2. Slide top cover forward slightly to move notches
away from the pegs on the front of the cabinet.
3. Lift the top cover up. To completely remove, lift
top cover away from both top cover hinges. Refer
to Figure 2.
After opening, or opening and closing the top cover,
the operator has 4 minutes and 15 seconds to begin
programming. If the appropriate Select Cycle Pads
have not been pressed in that time, the control will not
accept operator programming. Should this happen,
opening and closing the top cover will once again trip
the switch which allows access to the programming
options.
2
1
3
4
CHM1357R
CHM1357R
1
2
Top Cover Lock
Top Cover
3
4
Top Cover Hinge
Peg
Figure 2
12
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Entering the Manual Mode
For programming, testing, and retrieving information
from the control, it is often necessary to enter the
Manual Mode by following the six simple steps below.
How to Enter the Manual Mode
1. If accessing Diagnostic Tests, be sure the
machine is in Ready Mode before continuing to
step 2. If the machine is in an active cycle, rapid
advance through the cycle. Refer to the Rapid
Advance Feature. If coins or a card has been
entered, refer to Clear Vend Feature.
2. Open the top cover. Refer to Opening the Top
Cover.
NOTE: The coin vault switch must be closed to
enter Manual Mode.
3. While pressing and holding PERM PRESS/90C
keypad with one hand, press NORMAL/90C
keypad with the other hand.
4. The display will show “rAPd”.
By default, all groups are turned “ON”.
The manual features available in each group are as
follows (the menu displayed on the display in this
mode is in parentheses).
Manual Programming
Manual Programming (Prog)
Manual Read Audit (AUdt)
Manual Reset (rSEt)
Manual Rapid Advance
Rapid Advance (rAPd)
<
>
5. Press the NORMAL/40C ( ) keypad or the
PERM PRESS/40C ( ) keypad to scroll through
the options until the desired option appears in the
display.
Manual Mode is broken into two groups: Manual
Programming and Manual Rapid Advance. Manual
Programming can only be turned on or off with an
external device. Refer to the appropriate instruction
manual. Manual Rapid Advance can be turned on and
off using an external device or by manual
programming (refer to option 22 of Programming
Control).
6. Press the START (enter) keypad.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Programming Control
What Can Be Programmed?
Each description includes instructions on when and
why the option might be used and, more importantly,
how to program the option.
This feature allows the owner to program cycle
information, standard vend pricing, special vends and
other features by using the keypads. The control must
have the Manual Programming Mode enabled, which
is the factory default. This mode can only be turned
“OFF” and “ON” by using an external device. Refer to
this section when programming the control.
For more advanced users, a quick reference list of the
options available through the programming mode and
programming flowcharts are located on the following
pages.
NOTE: The letters and numbers in the Option
Display column of the Programmable Options
Available list are what will be shown in the display
when that option is selected.
This section offers a detailed description of all available
programmable options.
Programmable Options Available
Option
Number
Option
Display
Description
1
“AtS1”
2
Default Value
Value Range
Normal/90C Vend Price
200
0 - 65535
“dEn1”
Coin #1 Value
25
1 - 65535
3
“dEn2”
Coin #2 Value
100
1 - 65535
4
“PLSE”
Start Pulse Value
25
1 - 65535
5
“PLSn”
Start Pulse Mode
128
oFF/128/192
6
“AtyP”
Available Type
0
0-3
7
“dCYC”
Default Cycle
5*
1-9*
8
“oPL”
OPL Mode Enable/Disable
oFF
on/oFF
9
“AUd”
Audio Signal
29*
0-31*
10
“CArd”
Card Reader Display Control
oFF
on/oFF
11
“Err-”
Errors
-
-
“CEr-”
Coin Error Parameters
-
-
1.
“CEr1”
Coin Error
on
on/oFF
2.
“CEr2”
Coin Error Penalty
oFF
on/oFF
3.
“CEr3”
Coin Drops Header Present Error
on
on/oFF
b.
“E FL”
Fill Errors
on
on/oFF
c.
“E dr”
Drain Error
on
on/oFF
d.
“E Ub”
Unbalance Error Display
on
on/oFF
e.
“E oP”
Open Thermister Error Display
on
on/oFF
f.
“E SH”
Shorted Thermistor Error Display
on
on/oFF
g.
“E Ht”
Heat Error Display (Heater only)
on
on/oFF
a.
*Refer to programming section for value definition.
**Refer to the Cycle Chart for default cycle setting information.
Table 1 (continued)
14
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
Table 1 (continued)
Option
Number
h.
Option
Display
Description
Default Value
Value Range
“LEr-”
Water Leak Detection Error
-
-
1.
“LEr1”
Water Leak Detection During a
Machine Cycle (On/Off)
oFF
on/oFF
2.
“LEr2”
Water Leak Detection Day of Week
Enable
127*
0-127*
3.
“LEr3”
Number of cycles between Leak
Detection Test
0*
0-127*
“E Sd”
Slow Drain Detection
oFF
on/oFF
“CyC-”
Cycle Programming
“AgIt”
Cycle Agitate
-
-
1.
“tyPE”
Agitate Type
**
1-2*
2.
“ASPd”
Agitate Speed (VFD only)
**
Lo/rEg*
“SEg-”
Cycle Segment Programming
“SgEn”
Segment Enable/Disable
**
on/oFF
“FILL”
Fill Step
-
-
1.
“FLEn”
Fill Step Enable/Disable
**
on/oFF
2.
“FLEU”
Fill Level
**
HI/nEd/Lo
3.
“tEnP”
Fill Temperature
**
hot/UArn/CoLd – 35°F-194°F/2°C-90°C
“SUPL”
Supply Step
-
-
1.
“SUEn”
Supply Step Enable/Disable
**
on/oFF
2.
“dISP”
Dispenser Options
**
For Design 1 models, display will show
Cx (compartment-oriented) or Sx (supplyoriented), depending on how option 5
(Supply/Compartment Dispenser
Programming) is programmed.
For Design 2 models, Compartment and
Supply dispensing is programmed
separately.
Press START keypad to access options.
a.
“C2” or
“S1”
Compartment #2/Supply #1
(Design 1 models)
**
on/oFF
b.
“C3” or
“S2”
Compartment #3 /Supply #2
(Design 1 models)
**
on/oFF
c.
“C4”or
“S3”
Compartment #4/Supply #3
(Design 1 models)
**
on/oFF
d.
“S4”
Supply #4 (Design 1 models)
**
on/oFF
(1)
“C2”
Compartment #2 (Design 2 models)
**
on/oFF
(2)
“C3”
Compartment #3 (Design 2 models)
**
on/oFF
(3)
“C4”
Compartment #4 (Design 2 models)
**
on/oFF
i
12
a.
b.
1.
c.
d.
Refer to Cycle Chart for default cycle information
*Refer to programming section for value definition.
**Refer to the Cycle Chart for default cycle setting information.
Table 1 (continued)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Programming Control
Table 1 (continued)
Option
Number
Option
Display
Description
Default Value
Value Range
(4)
“S1”
Supply #1 (Design 2 models)
**
on/oFF
(5)
“S2”
Supply #2 (Design 2 models)
**
on/oFF
(6)
“S3”
Supply #3 (Design 2 models)
**
on/oFF
(7)
“S4”
Supply #4 (Design 2 models)
**
on/oFF
“SdUr”
Supply Duration
**
Press START keypad to access options
1.
“SEC”
Seconds
**
0-59
2.
“nIn”
Minutes
**
0-9
-
-
e.
f.
“AgSt”
Agitate Step
1.
“AgEn”
Agitate Step Enable/Disable
**
on/oFF
2.
“AdUr”
Agitate Duration (in minutes)
**
1-30 for agitate types 1 or 2
3.
“HEAt”
Heat in Agitate (if heater is present)
**
oFF/1/2**
g.
“drAn”
Drain Step
on
on/oFF
h.
“SPIn”
Extract Step
-
-
1.
“SPEn”
Extract Step Enable/Disable
**
on/oFF
2.
“SSEC”
Extract Seconds
**
0 - 59
3.
“SnIn”
Extract Minutes
**
Intermediate Extract: Min. Step Time = 30
seconds, Max. Step Time = 3:59 minutes
Final Extract: Min. Step Time = 30
seconds, Max. Step Time = 9:59 minutes
4.
“SSPd”
Extract Speed (VFD only)
**
1-5* (Design 1)
1-6* (Design 2)
“Cnin”
Cycle Time
0*
0-255 minutes
13
“SUPC”
Supply/Compartment Dispenser
Programming (Design 1 models
only)
C
(Compartment)
C (Compartment)/
S (Supply Dispenser)
14
“bALr”
Number of Balance Retries (VFD
only)
Design 1: 3
Design 2: 1
1-7
15
“IrA”
IR Access (On/Off)
on
on/oFF
16
“tFC”
Fahrenheit/Celsius
FAHr
(Fahrenheit)
FAHr (Fahrenheit)/CEL (Celsius)
17
“FH”
Hot Water Temperature
140°F (60°C)
35°F-194°F/2°C-90°C
18
“FHC”
Warm Water Temperature
100°F (38°C)
35°F-194°F/2°C-90°C
19
“FC”
35°F (2°C)
35°F-194°F/2°C-90°C
20
“Codn”
Cooldown Enable/Temperature
oFF
oFF or 50°F - 160°F /
10°C - 71°C
21
“PtEn”
Production Test Cycle (On/Off)
on
on/oFF
22
“rAEn”
Manual Rapid Advance (On/Off)
on
on/oFF
23
“nCtd”
No Cycle Time Display
oFF
on/oFF
i.
Cold Water Temperature
*Refer to programming section for value definition.
**Refer to the Cycle Chart for default cycle setting information.
Table 1 (continued)
16
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
Table 1 (continued)
Option
Number
Option
Display
Description
Default Value
Value Range
24
“PCtd”
Programmable Cycle Time Display
oFF
on/oFF
25
“SdAd”
Slow Drain Detection Adjust
0
0 - 255
26
“SPAU”
Pause/Resume Mode
oFF
on/oFF
27
“AtS2”
Normal/60C Vend Price
200
0 - 65535
28
“AtS3”
Normal/40C Vend Price
200
0 - 65535
29
“AtS4”
Perm Press/90C Vend Price
200
0 - 65535
30
“AtS5”
Perm Press/60C Vend Price
200
0 - 65535
31
“AtS6”
Perm Press/40C Vend Price
200
0 - 65535
32
“AtS7”
Perm Press/70C Vend Price
200
0 - 65535
33
“AtS8”
Perm Press/50C Vend Price
200
0 - 65535
34
“AtS9”
Delicate/30C Vend Price
200
0 - 65535
35
“rtC-”
Real-Time Clock
-
-
a.
“rtC1”
Set Real-Time Clock Minutes
-
0 - 59
b.
“rtC2”
Set Real-Time Clock Hours
-
0 - 23
c.
“rtC3”
Set Real-Time Clock Day
-
1 (Sunday)* - 7 (Saturday)
d.
“rtC4”
Set Real-Time Clock Date
-
1 - 31
e.
“rtC5”
Set Real-Time Clock Month
-
1 - 12
f.
“rtC6”
Set Real-Time Clock Year
-
0 (2000) - 99
g.
“rtC7”
Daylight Saving Option
on
on/oFF
“SPA-”
Special Vend A Data
-
-
a.
“SA01”
Special Vend A Days Enable
0*
0 - 255*
b.
“SA02”
Special Vend A Start Hour
-
0 - 23
c.
“SA03”
Special Vend A Start Minute
-
0 - 59
d.
“SA04”
Special Vend A Length in Hours
-
0 - 24
e.
“SA05”
Special Vend A Start Month
-
0 - 12
f.
“SA06”
Special Vend A Start Date
-
0 - 31
g.
“SA08”
Special Vend A End Month
-
0 - 12
h.
“SA09”
Special Vend A End Date
-
0 - 31
i.
“SA11”
Special Vend A Normal/90C Vend
Price
-
0 - 65535
j.
“SA12”
Special Vend A Normal/60C Vend
Price
-
0 - 65535
l.
“SA13”
Special Vend A Normal/40C Vend
Price
-
0 - 65535
m.
“SA14”
Special Vend A Perm Press/90C
Vend Price
-
0 - 65535
36
*Refer to programming section for value definition.
**Refer to the Cycle Chart for default cycle setting information.
Table 1 (continued)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Programming Control
Table 1 (continued)
Option
Number
Option
Display
Description
Default Value
Value Range
n.
“SA15”
Special Vend A Perm Press/60C
Vend Price
-
0 - 65535
o.
“SA16”
Special Vend A Perm Press/40C
Vend Price
-
0 - 65535
q.
“SA17”
Special Vend A Perm Press/70C
Vend Price
-
0 - 65535
r.
“SA18”
Special Vend A Perm Press/50C
Vend Price
-
0 - 65535
s.
“SA19”
Special Vend A Delicate/30C Vend
Price
-
0 - 65535
t.
“SA20”
Special Vend A Wash Agitate Step
Added Minutes
-
0 - 15
u.
“SA21”
Special Vend A Wash Agitate Step
Subtracted Minutes
-
0 - 15
37
“dAEn”
Manual Diagnostics (On/Off)
on
on/oFF
38
“FLo”
Low Water Level
3
1 - 10
39
“FnEd”
Medium Water Level
15
11 - 20
40
“FHI”
High Water Level
27
21 - 30
41
“ALd-”
Auto-Water Leak Detection
-
-
a.
“ALd1”
Auto-Water Leak Detection (On/Off
and cycles)
oFF
oFF/0 - 127 (Cycles)
b.
“ALd2”
Auto-Water Leak Detection Hour
0
0 - 23
c.
“ALd3”
Auto-Water Leak Detection Day of
Week
127*
0 - 127*
*Refer to programming section for value definition.
**Refer to the Cycle Chart for default cycle setting information.
Table 1
18
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
Programming Flowcharts
Entering Manual Mode
>
>
Enter Manual Mode.
1. Open top cover
2. Press and hold both NORMAL/90C ( ) keypad
and PERM PRESS/90C ( ) keypad.
“rAPd” - Quickly advance through active
cycles.
1. Press START (enter) keypad to begin Rapid
Advance cycle and advance through cycle
steps.
“Prog” - Program Cycle Information
and other features into the control.
1. Refer to the Manual Programming flowchart.
“CyC” - Total number of machine cycles:
1. Press START (enter) once to read audit.
“rCyC” - Total number of rapid advance cycles:
1. Press START (enter) once to read audit.
>
>
“AUdt” - Retrieve audit information for machine.
1. Press START (enter) keypad.
2. Press NORMAL/40C ( ) keypad or
PERM PRESS/40C ( ) keypad
to scroll through options.
“Coi1” - Total number of coins #1:
1. Press START (enter) once to read audit.
“Coi2” - Total number of coins #2:
1. Press START (enter) once to read audit.
“PLSE” - Total number of start pulses.
1. Press START (enter) once to read audit.
“rSEt” - Reset the control’s programming data
to factory default.
1. Press START (enter) keypad.
“dIAg” - Run diagnostic tests on machine
operations.
1. Press START (enter) keypad. Refer to
Diagnostic Tests flowchart.
CHM1333R
CHM1333R
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Programming Control
Manual Programming
“Prog” Enter Program Mode
“AtS1” - Set vend price for Normal/90° C wash.
“dEn1” - Set value for the #1 coin entered.
“dEn2” - Set value for the #2 coin entered.
“PLSE” - Program the value of the Start
Pulse.
“PLSn” - Program the Start Pulse Input for
one pulse or multiple pulses.
“AtyP” - Program when control provides an
available output for card and central pay.
“dCYC” - Set the default cycle and
temperature.
“oPL” - Enable/disable OPL Mode in which
no vend price needs to satisfied to operate
machine.
“AUd” - Program when the signal will sound.
“CArd” - Program whether the display is
controlled by machine’s electronic control or
the card reader.
“CEr1” - Coin Error
“CEr-” - Coin Error Parameters
“CEr2” - Coin Error Penalty
“CEr3” - Coin Drops Header Present Error
“E Fl” - Fill Error
“E dr” - Drain Error
“Err-” - Turn on/off certain errors in control.
“E Ub” - Unbalance Error (VFD only)
“E oP” - Open Thermistor Error
(Models with Heat)
“E SH” - Shorted Thermistor Error
(Models with Heat)
“E Ht” - Heat Error (heater only)
“CyC-” - Program aspects for the various
steps in each type of cycle. There are (9)
cycles available for programming.
“LEr1” - Water Leak Detection During
a Machine Cycle
“LEr-” - Leak Detection
“LEr2” - Water Leak Detection - Day
of Week
“E Sd” - Slow Drain Detection
“LEr3” - Number of Cycles between
Leak Detection Test
“tyPE” - Agitation Type:
1 = Normal
2 = Gentle
“AgIt” - Program the cycles agitation
action and speed
“ASPd” - Agitation Speed (VFD only):
“Lo” = Reduced Speed
“rEg” = Normal Speed
“SEg1” - Program options for each
segment. There are (8) segments
available for programming
“SgEn” - Segment Enabled/Disabled:
“on” = Enabled
“oFF” = Disabled
““FLEn” - Fill Step Enable/Disable:
“on” = Enabled
“oFF” = Disabled
“FILL” - Program fill step options
“FLEU” - Fill Level:
“HI” = High Level
“nEd” = Medium Level
“Lo” = Low Level
“tEnP” - Fill Temperature:
“CoLd” = Cold
“UArn” = Warm
“Hot” = Hot
(35°F - 194°F [2°C - 90°C])
(continued)
20
(continued)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
CHM1334R
F8238301
Programming Control
(continued)
(continued)
“SUEn” - Supply Step Enable/Disable:
“on” = Enabled
“oFF”” = Disabled
“SUPL” - Program supply step options
“dISP” Dispenser Options:
Press START (enter) to access options
“C2” or “S1” Compartment #2/
Supply #1:
“on” = Enabled
“oFF” = Disabled
(Design 1 Models)
“C2” - Compartment #2
“on” = Enabled
“oFF” = Disabled
(Design 2 Models)
“C3” or “S2” Compartment #3/
Supply #1:
“on” = Enabled
“oFF” = Disabled
(Design 1 Models)
“C3” - Compartment #3
“on” = Enabled
“oFF” = Disabled
(Design 2 Models)
“C4” or “S3” Compartment #4/
Supply #3:
“on” = Enabled
“oFF” = Disabled
(Design 1 Models)
“C4” - Compartment #4
“on” = Enabled
“oFF” = Disabled
(Design 2 Models)
“S4” - Supply #4:
“on” = Enabled
“oFF” = Disabled
“SEC” - Seconds:
“0” - “59”
“SdUr” Supply Duration:
Press START (enter) to access options
“nIn” - Minutes:
“0” - “9”
“S2” - Supply #2
“on” = Enabled
“oFF” = Disabled
(Design 2 Models)
“S3” - Supply #3
“on” = Enabled
“oFF” = Disabled
“AgEn” - Agitate Step
Enabled/Disabled:
“on” = Enabled
“oFF” = Disabled
“AgSt” - Program agitate step options
“S1” - Supply #1
“on” = Enabled
“oFF” = Disabled
(Design 2 Models)
“AdUr” - Agitate Duration (min):
“1” - “30”
“HEAt” - Heat in Agitate
(heat present only):
“oFF” = Disabled
“1” = To Target
“2” = Maintain
“drAn” - Enable/disable drain step
Drain Step:
“on” = Enabled
“oFF” = Disabled
“SPEn” - Extract Step
Enabled/Disabled:
“on” = Enabled
“oFF” = Disabled
“SPIn” - Program extract step options
“SSEC” - Extract Seconds:
“0” - “59”
“SnIn” - Extract Minutes:
“1” - “3” (Intermediate Step)
“1” - “9” (Final Step)
“Cnin” - Cycle Time
“0” - “255”
(continued)
“SSPd” - Extract Speed
(Design 1 - VFD only):
1 = Very Low Speed (80)
2 = Low Speed (80)
3 = Medium Speed (100)
4 = High Speed (120)
5 = Very High Speed (140)
“SSPd” - Extract Speed
(Design 2 - VFD only):
1 = Very Low Speed (27)
2 = Low Speed (80)
3 = Medium Speed (100)
4 = High Speed (125)
5 = Very High Speed (150)
6 = Ultra High Speed (200)
CHM1400R
CHM1400R
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Programming Control
(continued)
“SUPC” (Design 1 only) Choose either supply dispenser
or compartment dispenser.
Dispenser:
“S” = Supply Dispenser
“C” = Compartment Dispenser
“bALr” (VFD only) - Program the number
of times control will retry balancing the
load before moving to extract step.
“IrA” - Enable/disable the ability to read
the control by an external device.
“t FC” (Models with Heat) - Set
temperature shown in Fahrenheit or Celsius.
Temperature:
“CEL” = Celsius
“FAHr” = Fahrenheit
“FH” (Models with Heat) - Set
the temperature of the hot water.
“FHC” (Models with Heat) - Set the
temperature of the warm water.
“FC” (Models with Heat) - Set the
temperature of the cold water.
“Codn” (Models with Heat) - Enable/disable
the cool down water temperature option.
“PtEn” - Enable/disable access to the
production test cycle.
“rAEn” - Enable/disable the rapid advance
feature.
“nCtd” - Enable/disable whether the cycle
time will appear in display.
“PCtd” - Enable/disable
programmable cycle time display.
“SdAd” - Enable/disable slow drain
detection. When enabled can
increase/decrease the time before a slow
drain error will occur.
“SPAU” - Enable/disable Pause/Resume
Mode.
“AtS2” - Set vend price for normal/
60°C warm wash.
“AtS3” - Set vend price for Normal/
40°C wash.
“AtS4” - Set vend price for Perm Press/
90°C hot wash.
“AtS5” - Set vend price for Perm Press/
60°C warm wash.
“AtS6” - Set vend price for Perm Press
40°C cold wash.
“AtS7” - Set vend price for Perm Press
70°C hot wash.
“AtS8” - Set vend price for Perm Press
50°C warm wash.
“AtS9” - Set vend price for Delicate/
30°C cold wash.
(continued)
22
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
CHM1401R
CHM1401R
F8238301
Programming Control
(continued)
“rtC1” - Programs minutes:
“0” - “59”
“rtC2” - Programs Hours:
“0” - “23”
“rtC3” - Programs Day of Week:
“1” - “7”
“rtC-” - set the control’s internal clock.
“rtC4” - Programs Date of Month:
“1” - “31”
“rtC5” - Programs Month:
“1” - “12”
“rtC6” - Programs Year:
“0” - “99”
“rtC7” - Programs Daylight Saving:
“on” = Enabled
“oFF” = Disabled
“SA01” - Special Vend A Days
(refer to Table 13)
“SA02” - Special Vend A Start Hour
“SA03” - Special Vend A Start Minute
“SA04” - Special Vend A Length in Hours
“SA05” - Special Vend A Start Month
“SA06” - Special Vend A Start Date
“SPA-” - Enable/disable Special Vend A
option. When enabled can program day or
days with a special vend price.
“SA08” - Special Vend A End Month
“SA09” - Special Vend A End Date
“SA11” - Special Vend A Normal/90° C Vend Price
“SA12” - Special Vend A Normal/60° C Vend Price
“SA13” - Special Vend A Normal/40° C Vend Price
“SA14” - Special Vend A Perm Press/90° C Vend Price
“SA15” - Special Vend A Perm Press/60° C Vend Price
“SA16” - Special Vend A Perm Press/40° C Vend Price
“SA17” - Special Vend A Perm Press/70° C Vend Price
“SA18” - Special Vend A Perm Press/50° C Vend Price
“SA19” - Special Vend A Delicate/30° C Vend Price
“SA20” - Special Vend A Wash
Agitate Step Added Minutes
“SA21” - Special Vend A Wash
Agitate Step Subtracted Minutes
(continued)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
CHM543R
CHM543R
23
Programming Control
(continued)
“dAEn” - Enable/disable the manual
diagnostics option.
“FLo” - Program the low water level
during fill and tumble of all cycles.
“FnEd” - Program the medium water level
during fill and tumble of all cycles.
“FHI” - Program the high water level during
fill and tumble of all cycles.
“tCF” (Models with Heat) - Enable/disable a
temperature controlled fill.
“ALd1” - Auto-Water Leak Detection:
“on”, then “0” - “127”
“oFF”
“ALd-” - Set the time and frequency that the
control automatically checks the water level.
“ALd2”” - Auto-Water Leak Detection
Hour:
“0” - “23”
“ALd3” - Auto-Water Leak Detection
Day of Week:
“0” - “127”
CHM1356R
CHM1356R
24
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
Diagnostic
“dIAg” - Diagnostic Tests.
1. Press START (enter) keypad.
“d019” - VFD Balance Weight Test
“bAL” (Design 1 Models)
“d019” - Drive DC
Bus Display Test
“dCb”
(Design 2 Models)
“d020” - Water Purge Test
“PUrg”
“d021” - Water Leak Detection
Test
“Ld”
“d022” - Drive Software
Version # Test
“drxx”
(Design 2 Models)
“d023” - Drive Parameter Table
Version # Test
“dPxx”
(Design 2 Models)
“d024” - Drive Type Value
“dt x”
(Design 2 Models)
CHM1402R
CHM1402R
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Programming Control
This option allows the owner to set the vend price for a
NORMAL/90C wash. This vend price will be shown
in the display when NORMAL/90C is selected.
How to Program the Normal/90C Vend
Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad.
3. “AtS1” will appear in the display. Press the
START (enter) keypad. The NORMAL/90C LED
will be lit to show which cycle/temperature price is
being programmed.
4. There are five digits in NORMAL/90C Vend
Price. The fifth digit will appear in the display
and will flash one (1) second on, one (1) second
off. Refer to Figure 3.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
Normal/90C Vend Price “AtS1”
<
1.
8. Press the START (enter) keypad with the last
active digit. The next option, “dEn1”, will
appear in the display.
NOTE: To program “dEn1” (Coin #1 Value), refer
to option 2. To program other options, refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 3
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
26
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
If the Normal/90C Vend Price (option 1) is set for
“.75”, and the Coin Value is set for “00025”, the vend
price displayed will decrease by .25 for each coin
entered.
How to Program Coin #1 Value
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “dEn1” appears in
the display.
4. When “dEn1” appears in the display, press the
START (enter) keypad. There are five digits in
the Coin #1 Value. The fifth digit will appear in
the display and will flash one (1) second on, one
(1) second off. Refer to Figure 4.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
NOTE: The coin value can be set from 1 to 65,535.
Default coin value is 25.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set a specific
numerical value for a coin entered. For example, in the
United States the coin value for one quarter would be
measured in cents (25). Therefore, the coin value
entered for one quarter would be 00025.
<
>
Coin #1 Value “dEn1”
<
2.
8. Press the START (enter) keypad with the last
active digit. The next option, “dEn2”, will
appear in the display.
NOTE: To program “dEn2” (Coin #2 Value), refer
to option 3. To program other options, refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 4
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Programming Control
This option allows the owner to set a specific
numerical value for a coin entered when using the dual
coin drop. For example, the coin value for a dollar
coin would be measured in cents (100). Therefore, the
coin value entered for one dollar coin would be 00100.
If the Normal/90C Vend Price (option 1) is set for
“2.00”, and the Coin Value is set for “00100”, the
vend price displayed will decrease by 1.00 for each
dollar coin entered.
How to Program Coin #2 Value
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “dEn2” appears in
the display.
4. When “dEn2” appears in the display, press the
START (enter) keypad. There are five digits in
the Coin #2 Value. The fifth digit will appear in
the display and will flash one (1) second on and
one (1) second off. Refer to Figure 5.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
Coin #2 Value “dEn2”
<
3.
8. Press the START (enter) keypad with the last
active digit. The next option, “PLSE”, will
appear in the display.
NOTE: To program “PLSE” (Start Pulse Value),
refer to option 4. To program other options, refer to
the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
CHM507R
Figure 5
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The coin value can be set from 1 to 65,535.
Default coin value is 100.
28
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
This option allows the owner to program the value of
the Start Pulse if used for multiple pulses with an aftermarket central card reader or pay system. Refer to
option 5 for additional information.
How to Program Start Pulse Value
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “PLSE” appears in
the display.
4. When “PLSE” appears in the display, press the
START (enter) keypad. There are five digits in
the Start Pulse Value. The fifth digit will appear
in the display and will flash one (1) second on
and one (1) second off. Refer to Figure 6.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
Start Pulse Value “PLSE”
<
4.
8. Press the START (enter) keypad with the last
active digit. The next option, “PLSn”, will
appear in the display.
NOTE: To program “PLSn” (Start Pulse Mode),
refer to option 5. To program other options, refer to
the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
CHM507R
Figure 6
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The Start Pulse Value can be set from 1 to
65,535. Default Start Pulse Value is 25.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Programming Control
This option allows the owner to program the Start
Pulse Input. The Start Pulse Mode can be used for
after-market central pay or card systems. The central
system sends the start pulse to the Start Pulse Input of
the control to start the cycle. If set for single pulse, one
start pulse from the central system will put the control
in Start Mode. If set for multiple pulses, each pulse
will deduct from the vend price value set up in
option 4 (Start Pulse Value) until the vend is satisfied.
How to Program Start Pulse Mode
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “PLSn” appears in
the display.
4. When “PLSn” appears in the display, press the
START (enter) keypad. “oFF” or a number will
appear in the display. This number corresponds to
the current Start Pulse Mode Programming
Value.
5. Locate the desired number in the first column of
Table 2 below.
“PLSn”
Start Pulse
Mode Value
Start Pulse
ON/OFF
Single Pulse/
Multiple Pulses
“oFF”
OFF
OFF
128*
ON
Single Pulse
192
ON
Multiple Pulses
*Factory Default Setting
Table 2
6. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current number until correct.
>
Start Pulse Mode “PLSn”
<
5.
NOTE: To go back to the current programmable
option without changing the current value, press
the PERM PRESS/60C (<) keypad.
7. Press the START (enter) keypad when the correct
number appears in the display.
NOTE: To program “AtyP” (Available Type), refer
to option 6. To program other options, refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
30
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
6.
Available Type “AtyP”
This option allows the owner to program when the
control provides an available output for card and
central pay systems.
How to Program Available Type
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
Mode(s) in Which Available
Signal is Active
0*
Ready Mode only
1
Ready Mode, Partial Vend Mode
2
Ready Mode, End of Cycle Mode
3
Ready Mode, End of Cycle Mode,
Partial Vend Mode
*Factory Default Setting
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
Available Type
Value
6. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“dCYC”, will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtyP” appears in
the display.
Table 3
4. When “AtyP” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current Available Type Value.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current number to the desired number
selected from Table 3.
NOTE: To program “dCYC” (Default Cycle), refer
to option 7. To program other options, refer to the
appropriate section.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Programming Control
7.
Default Cycle “dCYC”
This option allows the owner to set the default cycle
and temperature the machine will enter when in the
Ready Mode. When programming the default cycle,
refer to Table 4.
How to Read Table 4
To determine the correct number required to program
Default Cycle, use the following table. The Default
Value column contains the number required in step 5.
The other column corresponds to cycle type.
How to Program Default Cycle
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
“dCYC”
Default Value
Cycle Type
1
Normal/90C
2
Normal/60C
3
Normal/40C
4
Perm Press/90C
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “dCYC” appears in
the display.
5*
Perm Press/60C
6
Perm Press/40C
7
Perm Press/70C
4. When “dCYC” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current default cycle value. Refer to Table 4.
8
Perm Press/50C
9
Delicate/30C
<
>
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
Table 4
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current number to the desired number selected
from Table 4.
*Factory Default Setting
6. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“oPL”, will appear in the display.
NOTE: To program “oPL” (OPL Mode), refer to
option 8. To program other options, refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
32
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
This option allows the owner to enable or disable the
OPL Mode in which no vend price needs to be
satisfied to operate the machine.
How to Program the OPL Mode Enable/
Disable
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “AUd”, will appear in the display.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
4. When “oPL” appears in the display, press the
START (enter) keypad. The current OPL Mode
Enable/Disable status will appear in the display.
“on” = Option Enabled
“oFF” = Option Disabled (Default Setting)
>
OPL Mode Enable/Disable“oPL”
<
8.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “oPL” appears in the
display.
F8238301
NOTE: To program “AUd” (Audio Signal), refer to
option 9. To program other options, refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Programming Control
This option allows the owner to program when the
signal will sound.
There are five occasions when a signal may sound
during operation. These five occasions are listed
below:
1. End of Cycle Signal
By default, the signal is turned off. If turned on,
the signal will sound for three (3) seconds at the
end of a cycle.
2. Keypad Depression Signal
By default, this signal is turned on and will sound
for a quarter of a second. This signal will sound
each time a keypad is pressed.
3. Coin Input/Card Insertion Signal
By default, this signal is turned on and will sound
for a quarter of a second each time a coin or card
is entered.
4. Remove Card Signal (Card Models Only)
By default, this signal is turned on and will sound
one (1) second on and one (1) second off when
the control is prompting for card removal.
5. Signal for Start
By default, this signal is turned on and will sound
one (1) second on and one (1) second off for 10
seconds after vend price has been satisfied.
4. When “AUd” appears in the display press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current Audio Signal Programming Value.
5. Locate the desired number in the first column of
Table 5 on the following page.
6. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current number until correct.
>
Audio Signal “AUd”
<
9.
For Example: A user might wish to have the signal
sound only when a keypad is pressed. Entering the
number “1” in step 5 would turn off all the options
except KEYPAD. In this instance, the signal would
sound only when a keypad is pressed.
7. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“CArd”, will appear in the display.
NOTE: To program “CArd” (Card Reader Display
Control), refer to option 10. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
How to Program the Audio Signal
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AUd” appears in
the display.
34
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
How to Read Table 5
To determine the correct number required to program
the Audio Signal, use the following chart. The Signal
Value column contains the number required in step 6.
The other columns correspond to individual options.
Each column of options contains a unique combination
of the words “ON” and “OFF” that indicates if that
column’s option is turned on or off when the Signal
Value is entered. Select the desired combination of
options and enter the number found in the Signal Value
column.
Signal Start Remove
Value Mode
Card
Coin/
Card
Input
End of
Key
Cycle Pressed
0
OFF
OFF
OFF
OFF
OFF
1
OFF
OFF
OFF
OFF
ON
2
OFF
OFF
OFF
ON
OFF
3
OFF
OFF
OFF
ON
ON
4
OFF
OFF
ON
OFF
OFF
5
OFF
OFF
ON
OFF
ON
6
OFF
OFF
ON
ON
OFF
7
OFF
OFF
ON
ON
ON
8
OFF
ON
OFF
OFF
OFF
9
OFF
ON
OFF
OFF
ON
10
OFF
ON
OFF
ON
OFF
11
OFF
ON
OFF
ON
ON
12
OFF
ON
ON
OFF
OFF
13
OFF
ON
ON
OFF
ON
14
OFF
ON
ON
ON
OFF
15
OFF
ON
ON
ON
ON
16
ON
OFF
OFF
OFF
OFF
17
ON
OFF
OFF
OFF
ON
18
ON
OFF
OFF
ON
OFF
19
ON
OFF
OFF
ON
ON
20
ON
OFF
ON
OFF
OFF
21
ON
OFF
ON
OFF
ON
22
ON
OFF
ON
ON
OFF
23
ON
OFF
ON
ON
ON
24
ON
ON
OFF
OFF
OFF
25
ON
ON
OFF
OFF
ON
26
ON
ON
OFF
ON
OFF
27
ON
ON
OFF
ON
ON
28
ON
ON
ON
OFF
OFF
29*
ON
ON
ON
OFF
ON
30
ON
ON
ON
ON
OFF
31
ON
ON
ON
ON
ON
*Factory Default Setting
Table 5
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Programming Control
10. Card Reader Display Control
“CArd”
NOTE: This feature does not need to be
programmed manually. The card reader itself
makes this determination.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
How to Program the Card Reader Display
Control
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “Err-”, will appear in the display.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
NOTE: To program “Err-” (Error Code
Programming), refer to option 11. To program
other options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “CArd” appears in
the display.
>
This option allows the owner to program whether the
display is controlled by the machine’s electronic
control or by the card reader.
4. When “CArd” appears in the display, press the
START (enter) keypad. The current Card Reader
Display Control Status will appear in the display.
“on” = Card Reader controls display
“oFF” = Machine Electronic Control controls
display (Default Setting)
36
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
11. Error Code Programming “Err-”
“CEr-”
Coin Error Parameters
This option allows the owner to turn on or turn off
certain errors in the control.
“CEr1”
Coin Error - Determines if
display will show error.
How to Program Error Code Programming
“CEr2”
Coin Error Penalty - If enabled,
coin error will erase previous
coins entered and reset the vend
price.
“CEr3”
Coin Drops Header
Present Error - If enabled and
coin drop header is unplugged,
control ignores coin inputs.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “Err-” appears in the
display.
“E FL”
Fill Error
“E dr”
Drain Error
“E Ub”
Unbalance Error Display (VFD only)
“E oP”
Open Thermistor Error Display
(Models with Heat)
“E SH”
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to select error code.
Shorted Thermistor Error Display
(Models with Heat)
“E Ht”
Heat Error Display (Heater only)
“LEr-”
Leak Detection Error
If Water Leak Detection during a machine
cycle is enabled, then, on the enabled day(s)
of the week, the control will check for water
leaks during running machine cycles. If a
leak is detected, the control will display the
“E Ld” error for one minute after the cycle is
completed. It will also light the right-most
decimal point on the display. The Water
Leak Dectection diagnostic test can be used
to verify the leak.
<
>
4. When “Err-” appears in the display, press the
START (enter) keypad. Refer to Table 6 for a list
of programmable error code parameters.
6. Press the START (enter) keypad when the correct
code appears in the display. The current status
will appear in the display.
<
>
7. “oFF” indicates the option is disabled. “on”
indicates the option is enabled. Press the
NORMAL/40C ( ) or the PERM PRESS/40C
( ) keypad to change the status.
8. Press the START (enter) keypad when the correct
status appears in the display. The next Error Code
Programming option will appear in the display.
“LEr1”
Water Leak Detection During a
Machine Cycle - Determines if
water level drops below target
level.
“LEr2”
Water Leak Detection During a
Machine Cycle Day of Week
Enable (Refer to Table 7).
“LEr3”
Number of cycles between Leak
Detection Tests.
>
NOTE: To program “CyC-” (Cycle Programming),
press the PERM PRESS/60C (<) keypad, then the
NORMAL/40C ( ) keypad and refer to option 12.
To program other options, refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
“E Sd”
Slow Drain Detection – Determines if
machine is draining slower than
normal.
If Slow Drain Detection is enabled, the
control will check for slow drain operation
during running machine cycles. If a slow
drain is detected, the control will display the
“E Sd” error for one minute after the cycle
is completed. It will also light the right-most
decimal point on the display.
Table 6
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Programming Control
Day(s) of the Week Enabled Values
Day Of Week
Value
SAT
FRI
THUR
WED
TUE
MON
SUN
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
OFF
OFF
OFF
OFF
OFF
OFF
ON
2
OFF
OFF
OFF
OFF
OFF
ON
OFF
3
OFF
OFF
OFF
OFF
OFF
ON
ON
4
OFF
OFF
OFF
OFF
ON
OFF
OFF
5
OFF
OFF
OFF
OFF
ON
OFF
ON
6
OFF
OFF
OFF
OFF
ON
ON
OFF
7
OFF
OFF
OFF
OFF
ON
ON
ON
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
9
OFF
OFF
OFF
ON
OFF
OFF
ON
10
OFF
OFF
OFF
ON
OFF
ON
OFF
11
OFF
OFF
OFF
ON
OFF
ON
ON
12
OFF
OFF
OFF
ON
ON
OFF
OFF
13
OFF
OFF
OFF
ON
ON
OFF
ON
14
OFF
OFF
OFF
ON
ON
ON
OFF
15
OFF
OFF
OFF
ON
ON
ON
ON
16
OFF
OFF
ON
OFF
OFF
OFF
OFF
17
OFF
OFF
ON
OFF
OFF
OFF
ON
18
OFF
OFF
ON
OFF
OFF
ON
OFF
19
OFF
OFF
ON
OFF
OFF
ON
ON
20
OFF
OFF
ON
OFF
ON
OFF
OFF
21
OFF
OFF
ON
OFF
ON
OFF
ON
22
OFF
OFF
ON
OFF
ON
ON
OFF
23
OFF
OFF
ON
OFF
ON
ON
ON
24
OFF
OFF
ON
ON
OFF
OFF
OFF
25
OFF
OFF
ON
ON
OFF
OFF
ON
26
OFF
OFF
ON
ON
OFF
ON
OFF
27
OFF
OFF
ON
ON
OFF
ON
ON
28
OFF
OFF
ON
ON
ON
OFF
OFF
29
OFF
OFF
ON
ON
ON
OFF
ON
30
OFF
OFF
ON
ON
ON
ON
OFF
31
OFF
OFF
ON
ON
ON
ON
ON
32
OFF
ON
OFF
OFF
OFF
OFF
OFF
33
OFF
ON
OFF
OFF
OFF
OFF
ON
34
35
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
36
OFF
ON
OFF
OFF
ON
OFF
OFF
37
OFF
ON
OFF
OFF
ON
OFF
ON
38
39
40
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
OFF
Table 7 (continued)
38
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
Table 7 (continued)
Day(s) of the Week Enabled Values
Day Of Week
Value
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
SAT
FRI
THUR
WED
TUE
MON
SUN
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Table 7 (continued)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Programming Control
Table 7 (continued)
Day(s) of the Week Enabled Values
Day Of Week
Value
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127*
SAT
FRI
THUR
WED
TUE
MON
SUN
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
*Factory Default Setting
Table 7
40
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
12. Cycle Programming “CyC-”
How to Program Cycle Agitate“AgIt”
This option allows the owner to program different
aspects for various steps in each type of cycle. There
are nine cycles available for programming.
This option allows the owner to program the cycle’s
agitation action and speed. These options apply to the
entire cycle.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “CyC-” appears in
the display. Press the START (enter) keypad and
“CyC1” will appear in the display.
>
<
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options. Refer to Table 8.
4. Press the START (enter) keypad when the
desired programmable option appears in the
display. The current status will appear in the
display. Refer to Table 8.
<
>
4. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the nine
cycles to program. Press the START (enter)
keypad when the desired cycle appears in the
display.
2. When “AgIt” appears in the display, press the
START (enter) keypad. The first Cycle Agitate
option will appear in the display.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Cycle Programming options until
“AgIt” appears in the display.
<
How to Enter Cycle Programming
<
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
Status
“tyPE”
Agitate Type
1 = Normal
2 = Gentle
“ASPd”
Agitate Speed
(VFD only)
“Lo” = Reduced Speed
“rEg” = Normal Speed
Table 8
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
>
>
NOTE: To program “AgIt” (Cycle Agitate),
continue to next option. To program other options,
press the NORMAL/40C ( ) or the PERM PRESS/
40C ( ) keypads and refer to the appropriate
section.
Description
<
5. The first Cycle Programming option, “AgIt”, will
appear in the display.
Final Spin
Step
6. Press the START (enter) keypad when the
desired status appears in the display. The next
Cycle Agitate option will appear in the display.
NOTE: To program “SEg1” (Cycle Segment 1)
press the PERM PRESS/60C (<) keypad and
continue to next Cycle Programming option. To
program other options, press the PERM PRESS/
60C (<) keypad and refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
eight programmable Cycle Segments until the
desired segment appears in the display.
2. When the desired segment appears in the display,
press the START (enter) keypad. “SgEn”
(Segment Enable/Disable) will appear in the
display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
Cycle Segment programmable options.
NOTE: If the Segment Enable/Disable is
programmed “oFF”, the other Cycle Segment
programming options can’t be accessed.
4. Press the START (enter) keypad when the
desired Cycle Segment programmable option
appears in the display.
1. When “FILL” appears in the display, press the
START (enter) keypad. The first Fill step
programming option will appear in the display.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Fill step options. Refer to Table 9.
>
There are eight programmable cycle segments. Within
each segment, there are several programmable options.
Programming Fill Step
<
How to Program Cycle Segment “SEg1”
NOTE: Fill Step “FLEn” must be enabled to scroll
through all Fill Step options.
3. Press the START (enter) keypad when the
desired option appears in the display. The current
status will appear in the display. Refer to Table 9.
Fill Step
Description
Status
“FLEn”
Fill Step
Enable/Disable
“on”/”oFF”
“FLEU”
Fill Level
“HI” = high level
“nEd” = medium level
“Lo” = low level
“tEnP”
Fill Temperature
“CoLd” = Cold
“UArn” = Warm
“Hot” = Hot
(35°F - 194°F
[2°C - 90°C])
Programming Segment Enable/Disable
NOTE: If the Segment Enable/Disable is
programmed “oFF”, the other Cycle Segment
programming options can’t be accessed.
3. Press the START (enter) keypad when the
desired status appears in the display. The next
Cycle Segment option, “FILL”, will appear in the
display.
>
<
5. Press the START (enter) keypad when the
desired status appears in the display. The next
Fill step option will appear in the display.
NOTE: To program “SUPL” (Supply Step),
continue to next Cycle Segment option. To program
other options, press the NORMAL/40C ( ) or the
PERM PRESS/40C ( ) keypads and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
<
>
NOTE: To program “FILL” (Fill Step), continue to
next Cycle Segment option. To program other
options, press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypads and refer to the
appropriate section.
4. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
>
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
Table 9
<
1. When “SgEn” appears in the display, press the
START (enter) keypad. The current Segment
Enable/Disable status will appear in the display.
“on” = Segment is enabled
“oFF” = Segment is disabled
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
42
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Supply step options. Refer to
Table 10.
NOTE: Supply Step “SUEn” must be enabled to
scroll through all Supply Step options.
3. Press the START (enter) keypad when the
desired option appears in the display. The current
status value will appear in the display. Refer to
Table 10.
NOTE: For the Dispenser options, the display will
show “Cx” or “Sx” depending whether or not the
control is programmed as compartment-oriented
or supply-oriented. Refer to option Supply/
Compartment Dispenser Programming.
>
<
5. Press the START (enter) keypad when the
desired status/value appears in the display. The
next Supply step option will appear in the
display.
NOTE: To program “AgSt” (Agitate Step),
continue to next Cycle Segment option. If in the
Dispenser Options or Supply Duration
programming option, press the PERM PRESS/60C
(<) keypad first. To program other options, press
the NORMAL/40C ( ) or the PERM PRESS/40C
( ) keypads and refer to the appropriate section.
>
1. When “SUPL” appears in the display, press the
START (enter) keypad. The first Supply step
programming option will appear in the display.
4. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status/value.
<
Programming Supply Step
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
Supply Step
“SUEn”
Description
Status/Value
Supply Step
“on”/“oFF”
Enable/Disable
“diSP”
Dispenser options
Press START (enter)
(Design 1 Models only)
to access options
“C2” or Compartment 2/
“on”/“oFF”
“S1”
Supply #1
“C3” or Compartment 3/
“on”/“oFF”
“S2”
Supply #2
“C4” or Compartment 4/
“on”/“oFF”
“S3”
Supply #3
“S4”
Supply #4
“on”/“oFF”
Dispenser options
Press START (enter)
(Design 2 Models only)
to access options
“C2”
Compartment 2
“on”/“oFF”
“C3”
Compartment 3
“on”/“oFF”
“C4”
Compartment 4
“on”/“oFF”
“S1”
Supply #1
“on”/“oFF”
“S2”
Supply #2
“on”/“oFF”
“S3”
Supply #3
“on”/“oFF”
“S4”
Supply #4
“on”/“oFF”
“SdUr”
Supply Duration
Press START (enter)
to access options
“SEC”
Seconds
0-59
“nIn”
Minutes
0-9
Table 10
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Programming Control
Programming Agitate Step
Programming Drain Step
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Agitate step options. Refer to
Table 11.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
“on” = Drain step is enabled
“oFF” = Drain step is disabled
Agitate
Step
Status/Value
“AgEn”
Agitate Step
Enable/Disable
“on”/“oFF”
“AdUr”
Agitate Duration
(in minutes)
1-30
“HEAt”
Heat in Agitate
(If heater is present)
“oFF”, 1 or 2
1 = to target
2 = maintain
3. Press the START (enter) keypad when the
desired status appears in the display. The next
Cycle Segment option, “SPIn”, will appear in the
display.
NOTE: To program “SPIn” (Extract Step),
continue to next Cycle Segment option. To program
other options press the NORMAL/40C ( ) or the
PERM PRESS/40C ( ) keypads and refer to the
appropriate section.
<
Description
NOTE: Drain must be enabled to activate Extract
step.
>
3. Press the START (enter) keypad when the
desired option appears in the display. The current
status/value will appear in the display. Refer to
Table 11.
<
<
NOTE: Agitate Step “AgEn” must be enabled to
scroll through all Agitate Step options.
>
1. When “drAn” appears in the display, press the
START (enter) keypad. The current status will be
displayed.
>
1. When “AgSt” appears in the display, press the
START (enter) keypad. The first Agitate step
programming option will appear in the display.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
Table 11
<
>
4. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status/value.
5. Press the START (enter) keypad when the
desired status/value appears in the display. The
next Agitate step option will appear in the
display.
<
>
NOTE: To program “drAn” (Drain Step), continue
to next Cycle Segment option. To program other
options, press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypads and refer to the
appropriate section.
NOTE: If drain step is disabled, the extract cycle
step will not be executed.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
44
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
NOTE: Extract Step “SPEn” must be enabled to
scroll through all Extract Step options.
3. Press the START (enter) keypad when the
desired option appears in the display. The current
status/value will appear in the display. Refer to
Table 12.
“SPEn”
Description
Status/Value
Extract Step
Enable/Disable
“on”/“oFF”
“SSEC” Extract Seconds
<
NOTE: To program “Cnin” (Cycle Time), continue
to next Cycle Segment option. To program other
options press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypads and refer to the
appropriate section.
>
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Extract step options. Refer to
Table 12.
5. Press the START (enter) keypad when the
desired status/value appears in the display. The
next Cycle Segment step option, “SEg2” will
appear in the display.
<
1. When “SPIn” appears in the display, press the
START (enter) keypad. The first Extract step
programming option will appear in the display.
Extract
Step
4. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status/value.
>
Programming Extract Step
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
0-59
“SnIn”
Extract Minutes Intermediate Extract:
minimum step time =
30 seconds
maximum step time =
3:59 minutes
Final Extract:
minimum step time =
30 seconds
maximum step time =
9:59 minutes
“SSPd”
Extract Speed* 1 = very low speed (80)
(G) (Design 1- 2 = low speed (80)
VFD only)
3 = medium speed (100)
4 = high speed (120)
5 = very high speed (140)
Extract Speed* 1 = very low speed (27)
(G) (Design 2- 2 = low speed (80)
VFD only)
3 = medium speed (100)
4 = high speed (125)
5 = very high speed (150)
6 = ultra high speed (200)
*F-speed machines use speeds 1-3.
Table 12
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
45
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Cycle Programming options until
“Cnin” appears in the display.
NOTE: The option “PCtd” Programmable Cycle
Time Display must be programmed “on” to access
the “Cnin” option, refer to option 24.
2. When “Cnin” appears in the display, press the
START (enter) keypad. The first Cycle time
value will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
value.
46
4. Press the START (enter) keypad when the
desired cycle time value appears in the display.
NOTE: Programming display time (in minutes)
does not actually change time in the cycle, only to
the displayed cycle time for the user.
NOTE: To program another cycle, repeat Cycle
Programming steps. To program other options,
press the NORMAL/40C ( ) or the PERM PRESS/
40C ( ) keypads and refer to the appropriate
section.
>
This option allows the owner to add minutes to the
cycles display time.
NOTE: The Program Cycle Time can be set from 0
to 255 minutes. The default value is 0.
<
How to Program Cycle Time “Cnin”
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
13. Supply/Compartment Dispenser
Programming “SUPC” (Design
1 Models Only)
14. Number of Balance Retries
“bALr” (Variable Frequency
Drives Only)
This option allows the owner to choose between the
supply dispenser or compartment dispenser.
This option allows the owner to program how many
times the control will retry balancing the load before
moving into Extract step.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “SUPC” appears in
the display.
4. When “SUPC” appears in the display, press the
START (enter) keypad. The current dispenser
option will appear in the display.
“S” = Supply Dispenser
“C” = Compartment Dispenser (Default
Setting)
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the dispenser
type.
6. Press the START (enter) keypad when the
desired dispenser type appears in the display. The
next option, “bALr” (VFD models) or “IrA” (2
speed models), will appear in the display.
NOTE: For VFD models: To program “bALr”
(Number of Balance Retries), refer to option 14.
For 2 speed models: To program “IrA” (IR Access
[on/off]), refer to option 15. To program other
options, refer to the appropriate section.
>
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “bALr” appears in
the display.
4. When “bALr” appears in the display, press the
START (enter) keypad. The current value will
appear in the display.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current value.
>
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad, and
“AtS1” will appear in the display.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad, and
“AtS1” will appear in the display.
<
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
How to Program Supply/Compartment
Dispenser Programming
How to Program Number of Balance
Retries
<
NOTE: Supply Dispenser must only be selected if
machine is connected to an external chemical
supply system.
NOTE: The number of balance retries can be set
from 1-7. Default balance retries is set for 3 for
Design 1 models and 1 for Design 2 models.
6. Press the START (enter) keypad when the
desired value appears in the display. The next
option, “IrA”, will appear in the display.
NOTE: To program “IrA” (IR Access [on/off]),
refer to option 15. To program other options, refer
to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Programming Control
15. IR Access (Enabled/Disabled)
“IrA”
16. Fahrenheit/Celsius “t FC”
(Models with Heat)
This option allows the owner to enable or disable
allowing the control to be read by an external device.
This option allows the owner to set whether the
display will be shown in Fahrenheit or Celsius.
How to Program the IR Access (Enabled/
Disabled)
How to Program Fahrenheit/Celsius
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “IrA” appears in the
display.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “t FC” appears in
the display.
>
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current number to the desired number.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “t FC” (Models with Heat) or “PtEn”
(Non-heat Models), will appear in the display.
6. Press the START (enter) keypad when the correct
number of degrees appears in the display. The
new value is saved and the next option, “FH”,
will appear in the display.
How to Exit Programming Feature
<
<
NOTE: For Models with Heat: To program “t FC”
(Fahrenheit/Celsius), refer to option 16. For Nonheat Models: To program “PtEn” (Production Test
Cycle [On/Off]), refer to option 21. To program
other options, refer to the appropriate section.
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
>
4. When “IrA” appears in the display, press the
START (enter) keypad. The current IR Access
status will appear in the display.
“on” = Option Enabled (Default Setting)
“oFF” = Option Disabled
4. When “t FC” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current Fahrenheit/Celsius setting.
“CEL” = Celsius
“FAHr” = Fahrenheit (Default Setting)
NOTE: To program “FH” (Hot Water
Temperature), refer to option 17. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
48
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
17. Hot Water Temperature “FH”
This option allows the owner to program the hot water
temperature for models equipped with heat.
How to Program Hot Water Temperature
This option allows the owner to program the warm
water temperature for models equipped with heat.
How to Program Warm Water Temperature
4. When “FH” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current Hot Water Temperature value.
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current Hot Water Temperature value to the
desired Hot Water Temperature value.
NOTE: Hot Water Temperature is selectable
between 35° and 194° Fahrenheit (2° and 90°
Celsius). Default temperature is 140° Fahrenheit
(60° Celsius).
WARNING
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “FHC” appears in
the display.
4. When “FHC” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current Warm Water Temperature value.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current Warm Water Temperature value to the
desired Warm Water Temperature value.
>
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “FH” appears in the
display.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
NOTE: Warm Water Temperature is selectable
between 35° and 194° Fahrenheit (2° and 90°
Celsius). Default temperature is 100° Fahrenheit
(38° Celsius).
WARNING
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
W748
NOTE: Refer to option 16 to select Celsius or
Fahrenheit display.
6. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“FHC”, will appear in the display.
NOTE: To program “FHC” (Warm Water
Temperature), refer to option 18. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
F8238301
18. Warm Water Temperature
“FHC”
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
W748
NOTE: Refer to option 16 to select Celsius or
Fahrenheit display.
6. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“FC”, will appear in the display.
NOTE: To program “FC” (Cold Water
Temperature), refer to option 19. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49
Programming Control
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “FC” appears in the
display.
4. When “FC” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current Cold Water Temperature value.
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current Cold Water Temperature value to the
desired Cold Water Temperature value.
How to Program Cooldown Enable/
Temperature
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “Codn” appears in
the display.
>
How to Program Cold Water Temperature
This option allows the owner to enable or disable the
Cooldown Water Temperature option. If enabled, the
owner can also set the cooldown water temperature.
<
This option allows the owner to program the cold
water temperature for models equipped with heat.
20. Cooldown Enable/Temperature
“Codn” (Models with Heat)
<
19. Cold Water Temperature “FC”
4. When “Codn” appears in the display, press the
START (enter) keypad. A number, or “oFF”, will
appear in the display. The number corresponds to
the current Cooldown Water Temperature value,
and “oFF” appears when cooldown is disabled.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
<
>
NOTE: Cold Water Temperature is selectable
between 35° and 194° Fahrenheit (2° and 90°
Celsius). Default temperature value is 35°
Fahrenheit (2° Celsius).
NOTE: Cooldown Water Temperature is selectable
between 50° and 160° Fahrenheit (10° and 71°
Celsius). Default temperature value is OFF
WARNING
6. Press the START (enter) keypad when the
desired value appears in the display.
To prevent personal injury, avoid contact
with inlet water temperatures higher than
125° Fahrenheit (51° Celsius) and hot
surfaces.
NOTE: Refer to option 16 to select Celsius or
Fahrenheit display.
W748
NOTE: Refer to option 16 to select Celsius or
Fahrenheit display.
6. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“Codn”, will appear in the display.
NOTE: To program “Codn” (Cooldown Enable/
Temperature), refer to option 20. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
7. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“PtEn”, will appear in the display.
NOTE: To program “PtEn” (Prouction Test Cycle
[on/off]), refer to option 21. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
50
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
21. Production Test Cycle (Enabled/
Disabled) “PtEn”
22. Manual Rapid Advance
(Enabled/Disabled) “rAEn”
This option allows the owner to enable or disable
access to the production test cycle. Refer to
Production Test Cycle section for more information.
This option allows the owner to enable or disable the
rapid advance feature. Refer to Rapid Advance
Feature section for more information.
How to Program the Production Test
Cycle (Enabled/Disabled)
How to Program the Manual Rapid
Advance (Enabled/Disabled)
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “PtEn” appears in
the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “rAEn” appears in
the display.
4. When “PtEn” appears in the display, press the
START (enter) keypad. The current Production
Test Cycle status will appear in the display.
“on” = Option Enabled (Default Setting)
“oFF” = Option Disabled
4. When “rAEn” appears in the display, press the
START (enter) keypad. The current Manual
Rapid Advance status will appear in the display.
“on” = Option Enabled (Default Setting)
“oFF” = Option Disabled
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “rAEn”, will appear in the display.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “nCtd”, will appear in the display.
>
<
>
>
<
<
>
<
<
<
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
NOTE: To program “rAEn” (Manual Rapid
Advance [on/off]), refer to option 22. To program
other options, refer to the appropriate section.
NOTE: To program “nCtd” (No Cycle Time
Display), refer to option 23. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
51
Programming Control
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “nCtd” appears in
the display.
4. When “nCtd” appears in the display, press the
START (enter) keypad. The current No Cycle
Time Display status will appear in the display.
“on” = Option Enabled (Default Setting)
“oFF” = Option Disabled
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “PCtd”, will appear in the display.
NOTE: To program “PCtd” (Programmable Cycle
Time Display), refer to option 24. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “PCtd” appears in
the display.
>
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
How to Program Programmable Cycle
Time Display
4. When “PCtd” appears in the display, press the
START (enter) keypad. The current
Programmable Cycle Time Display status will
appear in the display.
“on” = Option Enabled
“oFF” = Option Disabled (Default Setting)
NOTE: Enabling this option will not change the
cycle time, only the display time for the user. Refer
to option “Cnin” in Cycle Programming to
program minutes to the cycle time display.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
How to Program No Cycle Time Display
This option allows the owner to program the displayed
cycle time.
<
This option allows the owner to enable or disable
whether the cycle time will appear in the display.
24. Programmable Cycle Time
Display “PCtd”
<
23. No Cycle Time Display “nCtd”
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “SdAd”, will appear in the display.
NOTE: To program “SdAd” (Slow Drain
Detection Adjust Value), refer to option 25. To
program other options, refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
52
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
25. Slow Drain Detection Adjust
Value “SdAd”
26. Pause/Resume Mode (Enabled/
Disabled) “SPAU”
This option allows the owner to increase the Slow
Drain Detection threshold by adding additional
seconds to the threshold value. When enabled, it
increases the time before a Slow Drain Error will
occur.
This option allows the owner to enable or disable
Pause/Resume Mode. When enabled, users can press
the START keypad three times (during first three
minutes of cycle) to pause the cycle.
How to Program No Cycle Time Display
How to Program the Pause/Resume
Mode (Enabled/Disabled)
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “SdAd” appears in
the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “SPAU” appears in
the display.
4. When “SdAd” appears in the display, press the
START (enter) keypad. The current Slow Drain
Detection Adjust value will appear in the display.
4. When “SPAU” appears in the display, press the
START (enter) keypad. The current Pause/
Resume status will appear in the display.
6. Press the START (enter) keypad when the
desired value appears in the display. The next
option, “SPAU”, will appear in the display.
NOTE: To program “SPAU” (Pause/Resume
Mode), refer to option 26. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
F8238301
>
<
<
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
status.
>
>
<
NOTE: The Slow Drain Detection Adjust Value can
be set from 0 to 255 seconds. The default Slow
Drain Detection Adjust value is 0.
“on” = Option Enabled
“oFF” = Option Disabled (Default Setting)
<
>
<
<
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to change the current
value.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
6. Press the START (enter) keypad when the
desired status appears in the display. The next
option, “AtS2”, will appear in the display.
NOTE: To program “AtS2” (Normal/60C Vend
Price), refer to option 27. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
Programming Control
How to Program the Normal/60C Vend
Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad, and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtS2” appears in
the display. The NORMAL/60C LED will be lit
to show which cycle/temperature price is being
programmed.
4. When “AtS2” appears in the display, press the
START (enter) keypad. There are five digits in
the Normal/60C Vend Price. The fifth digit will
appear in the display and will flash one (1)
second on, one (1) second off. Refer to Figure 7.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set the vend price for a
normal/warm wash. This vend price will be shown in
the display when NORMAL/60C is selected.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
<
27. Normal/60C Vend Price “AtS2”
8. Press the START (enter) keypad with the last
active digit. The next option, “AtS3”, will appear
in the display.
NOTE: To program “AtS3” (Normal/40C Vend
Price), refer to option 28. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 7
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
54
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
How to Program the Normal/40C Vend
Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtS3” appears in
the display. The NORMAL/40C LED will be lit
to show which cycle/temperature price is being
programmed.
4. When “AtS3” appears in the display, press the
START (enter) keypad. There are five digits in
the Normal/40C Vend Price. The fifth digit will
appear in the display and will flash one (1)
second on, one (1) second off. Refer to Figure 8.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set the vend price for a
normal/cold wash. This vend price will be shown in
the display when NORMAL/40C is selected.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
<
28. Normal/40C Vend Price “AtS3”
8. Press the START (enter) keypad with the last
active digit. The next option, “AtS4”, will appear
in the display.
NOTE: To program “AtS4” (Perm Press/90C Vend
Price), refer to option 29. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 8
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55
Programming Control
How to Program the Perm Press/90C Vend
Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtS4” appears in
the display. The PERM PRESS/90C LED will be
lit to show which cycle/temperature price is
being programmed.
4. When “AtS4” appears in the display, press the
START (enter) keypad. There are five digits in
the Perm Press/90C Vend Price. The fifth digit
will appear in the display and will flash one (1)
second on, one (1) second off. Refer to
Figure 9.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set the vend price for a
perm press/hot wash. This vend price will be shown in
the display when PERM PRESS/90C is selected.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
<
29. Perm Press/90C Vend Price
“AtS4”
8. Press the START (enter) keypad with the last
active digit. The next option, “AtS5”, will appear
in the display.
NOTE: To program “AtS5” (Perm Press/60C Vend
Price), refer to option 30. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
CHM507R
Figure 9
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
56
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
How to Program the Perm Press/60C Vend
Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtS5” appears in
the display. The PERM PRESS/60C LED will be
lit to show which cycle/temperature price is
being programmed.
4. When “AtS5” appears in the display, press the
START (enter) keypad. There are five digits in
the Perm Press/60C Vend Price. The fifth digit
will appear in the display and will flash one (1)
second on, one (1) second off. Refer to Figure
10.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set the vend price for a
perm press/warm wash. This vend price will be shown
in the display when PERM PRESS/60C is selected.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
<
30. Perm Press/60C Vend Price
“AtS5”
8. Press the START (enter) keypad with the last
active digit. The next option, “AtS6”, will appear
in the display.
NOTE: To program “AtS6” (Perm Press/40C Vend
Price), refer to option 31. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
CHM507R
Figure 10
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
57
Programming Control
How to Program the PERM PRESS/40C
Vend Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtS6” appears in
the display. The PERM PRESS/40C LED will be
lit to show which cycle/temperature price is
being programmed.
4. When “AtS6” appears in the display, press the
START (enter) keypad. There are five digits in
the Perm Press/40C Vend Price. The fifth digit
will appear in the display and will flash one (1)
second on, one (1) second off. Refer to Figure 11.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set the vend price for a
perm press/cold wash. This vend price will be shown
in the display when PERM PRESS/40C is selected.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
<
31. Perm Press/40C Vend Price
“AtS6”
8. Press the START (enter) keypad with the last
active digit. The next option, “AtS7”, will appear
in the display.
NOTE: To program “AtS7” (Perm Press/70C Vend
Price), refer to option 32. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
CHM507R
Figure 11
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
58
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
How to Program the Perm Press/70C Vend
Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtS7” appears in
the display. The PERM PRESS/70C LED will be
lit to show which cycle/temperature price is
being programmed.
4. When “AtS7” appears in the display, press the
START (enter) keypad. There are five digits in
the Perm Press/70C Vend Price. The fifth digit
will appear in the display and will flash one (1)
second on, one (1) second off. Refer to Figure
12.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set the vend price for a
delicate/hot wash. This vend price will be shown in the
display when PERM PRESS/70C is selected.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
<
32. Perm Press/70C Vend Price
“AtS7”
8. Press the START (enter) keypad with the last
active digit. The next option, “AtS8”, will appear
in the display.
NOTE: To program “AtS8” (Perm Press/50C Vend
Price), refer to option 33. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
CHM507R
Figure 12
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
59
Programming Control
How to Program the Perm Press/50C Vend
Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtS8” appears in
the display. The PERM PRESS/50C LED will be
lit to show which cycle/temperature price is
being programmed.
4. When “AtS8” appears in the display, press the
START (enter) keypad. There are five digits in
the Perm Press/50C Vend Price. The fifth digit
will appear in the display and will flash one (1)
second on, one (1) second off. Refer to Figure
13.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set the vend price for a
delicate/warm wash. This vend price will be shown in
the display when PERM PRESS/50C is selected.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
<
33. Perm Press/50C Vend Price
“AtS8”
8. Press the START (enter) keypad with the last
active digit. The next option, “AtS9”, will appear
in the display.
NOTE: To program “AtS9” (Delicate/30C Vend
Price, refer to option 34. To program other options,
refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
CHM507R
Figure 13
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
60
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
How to Program the Delicate/30C Vend
Price
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “AtS9” appears in
the display. The DELICATE/30C LED will be lit
to show which cycle/temperature price is being
programmed.
4. When “AtS9” appears in the display, press the
START (enter) keypad. There are five digits in
the Delicate/30C Vend Price. The fifth digit will
appear in the display and will flash one (1)
second on, one (1) second off. Refer to Figure
14.
6. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
NOTE: To go back to the current programmable
option without changing the value of the active
digit, press the PERM PRESS/60C (<) keypad.
7. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
(enter) keypad to enter the value of the digit and
advance to the next digit.
>
This option allows the owner to set the vend price for a
delicate/cold wash. This vend price will be shown in
the display when DELICATE/30C is selected.
NOTE: The vend price can be set from 0 to 65,535.
Default vend price is 200.
<
34. Delicate/30C Vend Price “AtS9”
8. Press the START (enter) keypad with the last
active digit. The next option, “rtC-”, will appear
in the display.
NOTE: To program “rtC-” (Real-Time Clock),
refer to option 35. To program other options, refer
to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
CHM507R
Figure 14
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
61
Programming Control
35. Set Real-Time Clock “rtC-”
This option allows the owner to set the control’s
internal clock to the correct time and date.
How to Program the Time and Date
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “rtC-” appears in the
display. Press the START keypad and “rtC1” will
appear in the display.
<
>
4. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options. Refer to Table 13.
“rtC1”
Programs Minutes (0-59)
“rtC2”
Programs Hours (0-23)
“rtC3”
Programs Day of Week (1-7)
“rtC4”
Programs Date of Month (1-31)
“rtC5”
Programs Month (1-12)
“rtC6”
Programs Year (0-99)
“rtC7”
Programs Daylight Saving
(ON*, OFF)
NOTE: The hours will be displayed in military
time. For day of week, Sunday is considered day
one (1), Monday is day two (2) and so on. For year,
the year 2000 is “00”, the year 2001 is “01” and so
on.
If programming Daylight Saving, “rtC7”, “on”
enables Daylight Saving Time and “oFF” disables
Daylight Saving Time.
7. Press the START (enter) keypad when the correct
time or date appears in the display. The next Set
Real-Time Clock option will appear in the
display.
NOTE: To program “SPA-” (Special Vend A Data),
press the PERM PRESS/60C (<) keypad and refer
to option 36. To program other options, refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
*Factory Default Setting
Table 13
5. When the desired option appears in the display,
press the START (enter) keypad. The current
value will appear in the display.
<
>
6. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the minutes, hours, day of week, date of the
month, month, year to the correct time or date.
62
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
Special Vend A is used to change the standard vend
prices for special occasions. The special vend can be
programmed to start and end on a specific day or days
of the week.
The owner may also turn the Special Vend A option on
or off if desired.
How to Program Special Vend A Days
Enable “SA01”
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “SPA-” appears in
the display. Press the START (enter) keypad and
“SA01” will appear in the display.
F8238301
5. Locate the desired number in the first column of
Table 14 on the following pages.
6. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current number until correct.
>
This option allows the owner to set the day or days of
a special vend.
4. When “SA01” appears in the display, press the
START (enter) keypad. A number will appear in
the display that corresponds to the current
Special Vend A Days Enable Programming
Value.
<
36. Special Vend A Data “SPA-”
7. Press the START (enter) keypad when the correct
number appears in the display. The next Special
Vend A option, “SA02”, will appear in the
display.
NOTE: To program “SA02” (Special Vend A Start
Hour), continue to the next Special Vend A option.
To program other options, press the PERM
PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
63
Programming Control
How to Read Table 14
To determine the correct number required to program
the Special Vend Days Enable, use the following table.
The Special Vend Value column contains the number
required in step 6. The other columns correspond to
individual days.
Each column of days contains a unique combination of
the words “ON” and “OFF” that indicates if that
column’s day is turned on or off when the value is
entered. Select the desired combination of days and
enter the number found in the value column.
“SA01”
SPECIAL VEND
VALUE
SAT
FRI
THUR
WED
TUE
MON
SUN
ON/OFF
0*
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
3
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
5
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
7
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
9
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
11
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
13
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
15
OFF
OFF
OFF
OFF
ON
ON
ON
ON
17
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
19
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
21
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
23
OFF
OFF
OFF
ON
OFF
ON
ON
ON
25
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
27
OFF
OFF
OFF
ON
ON
OFF
ON
ON
29
OFF
OFF
OFF
ON
ON
ON
OFF
ON
31
OFF
OFF
OFF
ON
ON
ON
ON
ON
33
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
35
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
37
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
39
OFF
OFF
ON
OFF
OFF
ON
ON
ON
41
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
43
OFF
OFF
ON
OFF
ON
OFF
ON
ON
45
OFF
OFF
ON
OFF
ON
ON
OFF
ON
47
OFF
OFF
ON
OFF
ON
ON
ON
ON
49
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
51
OFF
OFF
ON
ON
OFF
OFF
ON
ON
53
OFF
OFF
ON
ON
OFF
ON
OFF
ON
55
OFF
OFF
ON
ON
OFF
ON
ON
ON
57
OFF
OFF
ON
ON
ON
OFF
OFF
ON
59
OFF
OFF
ON
ON
ON
OFF
ON
ON
61
OFF
OFF
ON
ON
ON
ON
OFF
ON
63
OFF
OFF
ON
ON
ON
ON
ON
ON
65
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
67
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
*Factory Default Setting
Table 14 (continued)
64
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
Table 14 (continued)
“SA01”
SPECIAL VEND
VALUE
SAT
FRI
THUR
WED
TUE
MON
SUN
ON/OFF
69
71
73
75
77
79
81
83
85
87
89
91
93
95
97
99
101
103
105
107
109
111
113
115
117
119
121
123
125
127
129
131
133
135
137
139
141
143
145
147
149
151
153
155
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Table 14 (continued)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
65
Programming Control
Table 14 (continued)
“SA01”
SPECIAL VEND
VALUE
157
159
161
163
165
167
169
171
173
175
177
179
181
183
185
187
189
191
193
195
197
199
201
203
205
207
209
211
213
215
217
219
221
223
225
227
229
231
233
235
237
239
241
243
SAT
FRI
THUR
WED
TUE
MON
SUN
ON/OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
Table 14 (continued)
66
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
Table 14 (continued)
“SA01”
SPECIAL VEND
VALUE
245
247
249
251
253
255
SAT
FRI
THUR
WED
TUE
MON
SUN
ON/OFF
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
ON
ON
Table 14
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
67
Programming Control
How to Program Special Vend A Start
Hour “SA02”
How to Program Special Vend A Start
Minute “SA03”
This option allows the owner to set the hour that
Special Vend A will begin, from 0-23.
This option allows the owner to set the minute that
Special Vend A will begin, from 0-59.
2. When “SA02” appears in the display, press the
START (enter) keypad. The current start time (in
military time) will appear in the display.
2. When “SA03” appears in the display, press the
START (enter) keypad. The current start minute
will appear in the display.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the start hour to the desired hour.
4. Press the START (enter) keypad when the correct
hour appears in the display. The next Special Vend
A option, “SA03”, will appear in the display.
NOTE: To program “SA03” (Special Vend A Start
Minute), continue to next Special Vend A option. To
program other options, press the PERM PRESS/
60C (<) keypad and refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
68
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the start minute to the desired minute.
<
<
NOTE: The hours will be displayed in military
time (0-23).
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA03” appears in the display.
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA02” appears in the display.
4. Press the START (enter) keypad when the correct
minute appears in the display. The next Special
Vend A option, “SA04”, will appear in the
display.
NOTE: To program “SA04” (Special Vend A
Length in Hours), continue to next Special Vend A
option. To program other options, press the PERM
PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
How to Program Special Vend A Length in
Hours “SA04”
How to Program Special Vend A Start
Month “SA05”
This option allows the owner to set the length in hours
for Special Vend A, from 0-24.
This option allows the owner to set the month that
Special Vend A will begin, from 1-12.
4. Press the START (enter) keypad when the correct
hour appears in the display. The next Special Vend
A option, “SA05”, will appear in the display.
NOTE: To program “SA05” (Special Vend A Start
Month), continue to next Special Vend A option. To
program other options, press the PERM PRESS/
60C (<) keypad and refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
>
2. When “SA05” appears in the display, press the
START (enter) keypad. The current start month
will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the start month to the desired month.
>
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current length of hours to the desired number
of hours.
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA05” appears in the display.
<
2. When “SA04” appears in the display, press the
START (enter) keypad. The current length in
hours will appear in the display.
NOTE: If Special Vend A Start Month, Start Date,
End Month, or End Date are programmed to zero
(default is zero), the Special Vend A will be active
every week on the days programmed in Table 14.
<
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA04” appears in the display.
If “0” is selected and Special Vend A is on,
Special Vend A will occur at the time and days of
week selected, regardless of the month.
4. Press the START (enter) keypad when the correct
month appears in the display. The next Special
Vend A option, “SA06”, will appear in the
display.
NOTE: To program “SA06” (Special Vend A Start
Date), continue to next Special Vend A option. To
program other options, press the PERM PRESS/
60C (<) keypad and refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
69
Programming Control
How to Program Special Vend A Start Date
“SA06”
How to Program Special Vend A End
Month “SA08”
This option allows the owner to set the date that
Special Vend A will begin, from 1-31.
This option allows the owner to set the month that
Special Vend A will end, from 1-12.
2. When “SA06” appears in the display, press the
START (enter) keypad. The current start date will
appear in the display.
2. When “SA08” appears in the display, press the
START (enter) keypad. The current end month
will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the start date to the desired date.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the end month to the desired month.
>
<
<
>
<
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA08” appears in the display.
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA06” appears in the display.
If “0” is selected and Special Vend A is on,
Special Vend A will occur at the time and days of
week selected, regardless of the date.
If “0” is selected and Special Vend A is on,
Special Vend A will occur at the time and day of
week selected, regardless of the month.
4. Press the START (enter) keypad when the correct
date appears in the display. The next Special Vend
A option, “SA08”, will appear in the display.
4. Press the START (enter) keypad when the correct
month appears in the display. The next Special
Vend A option, “SA09”, will appear in the
display.
NOTE: To program “SA08” (Special Vend A End
Month), continue to next Special Vend A option. To
program other options, press the PERM PRESS/
60C (<) keypad and refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
70
NOTE: To program “SA09” (Special Vend A End
Date), continue to next Special Vend A option. To
program other options, press the PERM PRESS/
60C (<) keypad and refer to the appropriate
section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
How to Program Special Vend A End Date
“SA09”
This option allows the owner to set the date that
Special Vend A will end, from 1-31.
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA09” appears in the display.
2. When “SA09” appears in the display, press the
START (enter) keypad. The current end date will
appear in the display.
4. Press the START (enter) keypad when the correct
date appears in the display. The next Special Vend
A option, “SA11”, will appear in the display.
NOTE: To program “SA11” (Special Vend A
Normal/90C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the end date to the desired date.
If “0” is selected and Special Vend A is on,
Special Vend A will occur at the time or days of
week selected, regardless of the date.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
71
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA11” appears in the display.
2. When “SA11” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Normal/90C Vend Price. The
fifth digit will appear in the display and will flash
one (1) second on and one (1) second off. Refer
to Figure 15.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
NORMAL/90C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Normal/
90C Vend Price “SA11”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA12”, will appear in the display.
NOTE: To program “SA12” (Special Vend A
Normal/60C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 15
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
72
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA12” appears in the display.
2. When “SA12” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Normal/60C Vend Price. The
fifth digit will appear in the display and will flash
one (1) second on and one (1) second off. Refer
to Figure 16.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
NORMAL/60C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Normal/
60C Vend Price “SA12”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA13”, will appear in the display.
NOTE: To program “SA13” (Special Vend A
Normal/40C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 16
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
73
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA13” appears in the display.
2. When “SA13” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Normal/40C Vend Price. The
fifth digit will appear in the display and will flash
one (1) second on and one (1) second off. Refer
to Figure 17.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
NORMAL/40C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Normal/
40C Vend Price “SA13”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA14”, will appear in the display.
NOTE: To program “SA14” (Special Vend A Perm
Press/90C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 17
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
74
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA14” appears in the display.
2. When “SA14” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Perm Press/90C Vend Price.
The fifth digit will appear in the display and will
flash one (1) second on and one (1) second off.
Refer to Figure 18.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
PERM PRESS/90C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Perm
Press/90C Vend Price “SA14”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA15”, will appear in the display.
NOTE: To program “SA15” (Special Vend A Perm
Press/60C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 18
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
75
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA15” appears in the display.
2. When “SA15” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Perm Press/60C Vend Price.
The fifth digit will appear in the display and will
flash one (1) second on and one (1) second off.
Refer to Figure 19.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
PERM PRESS/60C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Perm
Press/60C Vend Price “SA15”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA16”, will appear in the display.
NOTE: To program “SA16” (Special Vend A Perm
Press/40C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 19
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
76
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA16” appears in the display.
2. When “SA16” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Perm Press/40C Vend Price.
The fifth digit will appear in the display and will
flash one (1) second on and one (1) second off.
Refer to Figure 20.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
PERM PRESS/40C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Perm
Press/40C Vend Price “SA16”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA17”, will appear in the display.
NOTE: To program “SA17” (Special Vend A Perm
Press/70C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 20
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
77
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA17” appears in the display.
2. When “SA17” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Perm Press/70C Vend Price.
The fifth digit will appear in the display and will
flash one (1) second on and one (1) second off.
Refer to Figure 21.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
PERM PRESS/70C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Perm
Press/70C Vend Price “SA17”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA18”, will appear in the display.
NOTE: To program “SA18” (Special Vend A Perm
Press/50C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 21
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
78
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA18” appears in the display.
2. When “SA18” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Perm Press/50C Vend Price.
The fifth digit will appear in the display and will
flash one (1) second on and one (1) second off.
Refer to Figure 22.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
PERM PRESS/50C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Perm
Press/50C Vend Price “SA18”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA19”, will appear in the display.
NOTE: To program “SA19” (Special Vend A
Delicate/30C Vend Price), continue to next Special
Vend A option. To program other options, press the
PERM PRESS/60C (<) keypad and refer to the
appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 22
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
79
Programming Control
<
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA19” appears in the display.
2. When “SA19” appears in the display, press the
START (enter) keypad. There are five digits in
the Special Vend A Delicate/30C Vend Price. The
fifth digit will appear in the display and will flash
one (1) second on and one (1) second off. Refer
to Figure 23.
NOTE: If the vend price is $100.00 or more, the
fifth digit is “1-6”. If the vend price is $99.99 or
less, the fifth digit is “0”.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the active digit and the START
keypad to enter the value of the digit and advance
to the next digit.
>
This option allows the owner to set the vend price for a
DELICATE/30C wash in Special Vend A. The
corresponding LED will be lit while programming.
NOTE: To go back to the current programmable
Special Vend A option without changing the value
of the active digit, press the PERM PRESS/60C (<)
keypad.
<
How to Program Special Vend A Delicate/
30C Vend Price “SA19”
6. Press the START (enter) keypad with the last
active digit. The next Special Vend A option,
“SA20”, will appear in the display.
NOTE: To program “SA20” (Special Vend A Wash
Agitate Step Added Minutes), continue to next
Special Vend A option. To program other options,
press the PERM PRESS/60C (<) keypad and refer
to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
CHM507R
Figure 23
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the value of the fifth digit.
NOTE: The vend price can be set from 0 to 65,535.
4. Press the START (enter) keypad to enter the fifth
digit and display remaining four digits. The
active digit will flash one (1) second on and one
(1) second off.
80
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
How to Program Special Vend A Wash
Agitate Step Added Minutes “SA20”
How to Program Special Vend A Wash
Agitate Step Subtracted Minutes “SA21”
This option allows the owner to add time to the wash
agitate part of the cycle in Special Vend A.
This option allows the owner to subtract time from the
wash agitate part of the cycle in Special Vend A.
2. When “SA20” appears in the display, press the
START (enter) keypad.
2. When “SA21” appears in the display, press the
START (enter) keypad.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the number of minutes displayed to the desired
number of added minutes.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the number of minutes displayed to the desired
number of subtracted minutes.
4. Press the START (enter) keypad when the correct
number of minutes appears in the display. The
next Special Vend A option, “SA21”, will appear
in the display.
>
<
<
>
<
<
NOTE: The Special Vend A Added Wash Agitate
Time can be set from zero “0” to 15 minutes.
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA21” appears in the display.
>
1. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable Special Vend A options until
“SA20” appears in the display.
NOTE: The Special Vend A Subtracted Wash
Agitate Time can be set from zero “0” to 15
minutes.
4. Press the START (enter) keypad when the correct
number of minutes appears in the display. The
next Special Vend A option, “SA01”, will appear
in the display.
NOTE: To program “SA21” (Special Vend A Wash
Agitate Step Subtracted Minutes), continue to next
Special Vend A option. To program other options,
press the PERM PRESS/60C (<) keypad and refer
to the appropriate section.
NOTE: To program “FLo” (Low Water Level),
press the PERM PRESS/60C (<) keypad and refer
to option 37. To program other options refer to the
appropriate section.
How to Exit Programming Feature
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
81
Programming Control
37. Low Water Level “FLo”
38. Medium Water Level “FnEd”
This option allows the owner to program the low water
level during fill and tumble of all cycles.
This option allows the owner to program the medium
water level during fill and tumble of all cycles.
How to Program Low Water Level
How to Program Medium Water Level
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “FLo” appears in the
display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “FnEd” appears in
the display.
4. When “FLo” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current low water level during tumble and fill of
all cycles.
4. When “FnEd” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current medium water level during tumble and
fill of all cycles.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current water level to the desired water level.
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current water level to the desired water level.
NOTE: The Low Water Level value can be set from
1 to 10. Default Low Water Level value is 3.
NOTE: The Medium Water Level value can be set
from 11 to 20. Default Medium Water Level value
is 15.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
82
>
<
<
>
>
NOTE: To program “FnEd” (Medium Water
Level), refer to option 38. To program other
options, refer to the appropriate section.
<
>
<
<
<
6. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“FnEd”, will appear in the display.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
6. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“FHI”, will appear in the display.
NOTE: To program “FHI” (High Water Level),
refer to option 39. To program other options, refer
to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Programming Control
4. When “FHI” appears in the display, press the
START (enter) keypad. A number will appear in
the display. This number corresponds to the
current high water level during tumble and fill of
all cycles.
<
>
5. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to increase or decrease
the current water level to the desired water level.
NOTE: The High Water Level value can be set
from 21 to 30. Default High Water Level value is
27.
6. Press the START (enter) keypad when the correct
number appears in the display. The next option,
“ALd-”, will appear in the display.
NOTE: To program “ALd-” (Auto-Water Leak
Detection), refer to option 40. To program other
options, refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
How to Program the Auto-Water Leak
Detection
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
>
<
>
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “FHI” appears in the
display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options until “ALd-” appears in
the display. Press the START keypad and
“ALd1” will appear in the display.
>
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “Prog” appears in
the display. Press the START (enter) keypad and
“AtS1” will appear in the display.
4. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through the
programmable options. Refer to Table 15.
>
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
<
How to Program High Water Level
This option allows the owner to set the time and
frequency that the control automatically checks the
water level. The owner programs which day(s) of the
week and hour of day(s) they want this test to occur.
The owner may also program this test to occur after
XX number of machine cycles have been completed
since the last time the test was run. In order for this
auto-water leak detection test to occur, the machine’s
door must be closed.
<
This option allows the owner to program the high
water level during fill and tumble of all cycles.
40. Auto-Water Leak Detection
“ALd-”
<
39. High Water Level “FHI”
“ALd1”
Auto-Water Leak Detection (“oFF”* or “0”
through “127” cycles [“on”] – Number of
completed cycles after which this test will
occur)
“ALd2”
Auto-Water Leak Detection Hour (“0”* –“23”
– Hour of the day this test will occur)
“ALd3”
Auto-Water Leak Detection Day of Week
(“0” –“127”* – Refer to Table 7)
*Factory Default Setting
Table 15
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
83
Programming Control
5. When the desired option appears in the display,
press the START (enter) keypad. The current
value will appear in the display.
<
>
6. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to enable during cycles,
disable, increase or decrease the hours, or day.
NOTE: The hours will be displayed in military
time. For day of week, Sunday is considered day
one (1), Monday is day two (2) and so on. Refer to
Table 7.
84
7. Press the START (enter) keypad when the correct
value appears in the display. The next option
“AtS1”, will appear in the display.
NOTE: To program “AtS1” (Normal/90C Vend
Price), refer to option 1. To program other options,
refer to the appropriate section.
How to Exit Programming Feature
Press the PERM PRESS/60C (<) keypad until the
control returns to Ready Mode.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Collecting Audit Information
This feature allows the owner to retrieve audit
information stored in the machine by pressing a
sequence of pads on the control. For an explanation of
the audit options available, refer to Table 16.
Audit Options List
#
Display
1
“CyC”
How to Enter Audit Feature
2
There are two methods the owner can use to enter the
Audit Feature.
3
“rCyC” Total # of rapid advanced cycles
“Coi1” Total # of coins #1
4
“Coi2”
Entering the Audit Feature by Manual
Mode
5
“PLSE” Total # of Start Pulses
1. Control must be in Manual Mode to start. Refer
to Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “AUdt” appears.
3. Press the START (enter) keypad. “CyC” will
appear.
Entering the Audit Feature with the Coin
Vault Open
1. Open coin vault. Make sure top cover is closed.
2. Press the START (enter) keypad.
How to Read Audit Data
<
>
1. Use the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad to scroll through various
options until the desired option is shown in the
display. Refer to the Audit Options List, Table
16, for an explanation of the audit options
available.
Description
Total # of machine cycles
Total # of coins #2
Table 16
2. Once the desired option appears in the display,
press the START (enter) keypad once to start the
audit count. At this point, the display will show
the first four-digit segment of the audit value. If
the audit count is 10,000 or higher, press the
START (enter) keypad again to view the last four
digits of the number.
NOTE: The display can show up to 4 digits at one
time. Audit counts 10,000 or higher are separated
into two 4-digit segments. Each time the START
(enter) keypad is pressed in step 2, the display will
show the next 4-digit segment in the audit value. If
the value is 9,999 or less, only one 4-digit segment
will be shown.
For Example: In the Total Number of Coins #1 option
with “Coi1” shown in the display, the audit has
counted 10,009 coins. Pressing the START (enter)
keypad one time will show “_ _ _ 1” to represent ten
thousand. Pressing the START (enter) keypad a second
time will display “0009” meaning nine. The total
equals “00010009” or 10,009.
3. Press the START (enter) keypad again. The
control will go to the next audit option in the
Audit Options List.
4. To select other audit options, repeat steps 1 – 4.
How to Exit Audit Feature
Press the PERM PRESS/60C (<) keypad.
NOTE: To exit Audit Feature when using Coin
Vault Open method, owner must close coin vault.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
85
Manual Reset
This feature allows the owner to reset the machine
control’s programming data to the factory default
settings by pressing a sequence of pads on the control.
For an explanation of the Factory Default Settings,
refer to Programming Control.
How to Enter Manual Reset
1. Control must be in Manual Mode to start.
Refer to Entering the Manual Mode.
<
>
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “rSEt” appears.
3. Press the START (enter) keypad. The control will
be blank until the programming is complete.
Once the program has been reset, the control will
display the next Manual Mode option, “diAg”.
86
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Testing Machine and
Electronic Control Functions
How to Enter Diagnostic Testing Feature
This feature allows the owner to run diagnostic tests
on various machine operations without servicing the
machine. The following tests are available:
1. Control must be in Manual Mode. Refer to
Entering the Manual Mode.
• Balance Weight Test (VFD models) (Design 1
models only)
<
>
2. Press the NORMAL/40C ( ) or the
PERM PRESS/40C ( ) keypad until “dIAg”
appears.
• Water Purge Test
• Water Leak Detection Test
3. Press the START (enter) keypad. Display will
change to “d001” indicating the front end control
software version number test.
The following tests are available on Design 2 models
only:
4. Press the NORMAL/40C ( ) or the
PERM PRESS/40C ( ) keypad to scroll through
the diagnostic test options.
<
>
• Drive Software Version Number
• Drive Parameter Table Version Number
• Drive Type Value
How to Start Tests
• Drive DC Bus Display Test
To start a diagnostic test, refer to the quick reference
chart (Table 17). Press the START (enter) keypad
when the desired test number is displayed. For detailed
information on each test, read the appropriate description.
How to Exit Diagnostic Testing Feature
Press the PERM PRESS/60C (<) keypad. The display
will return to the previous mode of operation.
Diagnostic (Testing) Mode – Quick Reference Chart
Test Number
Diagnostic Mode
Display
VFD Balance Weight Test (Design 1 models)
“bAL”
Drive DC Bus Display Test (Design 2 models)
“dCb”
“d020”
Water Purge Test
“PUrg”
“d021”
Water Leak Detection Test
“Ld”
“d022” (Design 2 models only)
Drive Software Version Number
“drxx”
“d023” (Design 2 models only)
Drive Parameter Table Version Number
“dPxx”
“d024” (Design 2 models only)
Drive Type Value
“dt x”
“d019”
Table 17
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
87
Testing Machine and Electronic Control Functions
VFD Balance Weight Test (Design 1
Models)
Water Purge Test
This test is only available on machines equipped with
a variable frequency motor drive.
To start test, control must be in the Diagnostic Testing
Mode. Refer to How to Enter Diagnostic Testing
Feature at the beginning of this section.
This option empties all water from the machine.
To start test, control must be in the Diagnostic Testing
Mode. Refer to How to Enter Diagnostic Testing
Feature at the beginning of this section.
To enter, press the START (enter) keypad. The display
will show “bAL” and the START keypad LED will
flash. Close the door. Press the START (enter) keypad.
The door will lock. The motor will turn at distribution
speed. The control monitors the VFD balance switch
for frequency and displays a corresponding message.
Refer to Table 18.
VFD Balance
Switch Frequency
0
Description
Display
Switch is always
closed
“CLoS”
1 Hz
“1 H”
2 Hz
“2 H”
3 Hz
“3 H”
Switch is always
open
“oPEn”
Table 18
Press the START (enter) keypad to stop the test. The
door will not unlock until the basket stops or the coast
time has expired.
Drive DC Bus Display Test (Design 2
Models)
This test is only available on machines equipped with
a custom drive.
To start test, control must be in the Diagnostic Testing
Mode. Refer to How to Enter Diagnostic Testing
Feature at the beginning of this section.
To enter, press the START (enter) keypad. The display
will show “dCb” and the START keypad LED will
flash. Close the door. Press the START (enter) keypad.
The door will lock. The control will turn on the drive
and ramp up the motor to distribution speed. The
drive’s DC Bus Voltage will display.
88
To enter, press the START (enter) keypad. The display
will show “PUrg” and the START keypad LED will
flash. Close the door. Press the START (enter) keypad.
The door will lock. The display will show “FLSH”.
The control will energize all water valves and supply
outputs while keeping the drain valves open.
The test will end, return to Water Purge Test start
prompt, and door will unlock if any keypad is pressed,
the door is unlocked or opened, if an end test
communication is received or if two minutes has
occurred since the test began. The control will prevent
the door from being unlocked until there is no water in
the machine.
Water Leak Detection Test
This option allows the owner to test for a water leak in
the machine.
To start test, control must be in the Diagnostic Testing
Mode. Refer to How to Enter Diagnostic Testing
Feature at the beginning of this section.
To enter, press the START (enter) Keypad. The display
will show “Ld” and the START keypad LED will flash
if the door is closed. Press the START (enter) keypad.
The door will lock. The control closes the drain valve
and fills the machine with cold water to low level. The
water level is monitored for 2 minutes and the display
shows an alternating horizontal segment while the
control is monitoring the water level. If after 2 minutes
the water level is the same, control will display
“PASS”, water will drain, door will unlock and
control will return to Ready Mode. If water level is
lower, indicating a leak in the drain, control will
display “FAIL”, water will drain, door will unlock and
water leak detection error will display as “E Ld”.
On Design 2 models, if water level is higher,
indicating a leak in the fill valve, control will display
“FAIL”, water will drain, door will unlock and water
leak detection error will display as “E LF”.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Testing Machine and Electronic Control Functions
Drive Software Version Number Test
(Design 2 models only)
This option displays the custom drive software version
number. To start test, control must be in the Diagnostic
Testing Mode. Refer to How to Enter Diagnostic
Testing Feature at the beginning of this section.
To enter, press the START (enter) keypad. The display
will show “drxx” where “xx” is the custom drive
software version number.
To exit the Custom Drive Software Version Number
Test, press the PERM PRESS/60C (<) keypad. The
control will return to the Diagnostic Testing Mode.
Drive Parameter Table Version Number
(Design 2 models only)
This option displays the custom drive parameter table
version number. To start test, control must be in the
Diagnostic Testing Mode. Refer to How to Enter
Diagnostic Testing Feature at the beginning of this
section.
Production Test Cycle
To Enter Production Test Cycle
1. Be certain control is in Ready Mode and top
cover or coin vault is open.
2. While pressing and holding the NORMAL/40C
keypad with one hand, press the PERM PRESS/
70C keypad with the other hand.
3. When the control enters the Production Test
Cycle, it will first display “S xx” with the “xx”
showing the software version of the front end
control.
4. The control will advance through the sequence of
test steps whenever any key is pressed. Refer to
Table 20 for all tests in the Production Test
Cycle.
To Exit Production Test Cycle
To exit a test step, power down the machine.
To enter, press the START (enter) keypad. The display
will show “dPxx” where “xx” is the custom drive
parameter table version number.
To exit the Custom Drive Parameter Table Version
Number Test, press the PERM PRESS/60C (<)
keypad. The control will return to the Diagnostic
Testing Mode.
Drive Type Value (Design 2 models only)
This option displays the custom drive type value. To
start test, control must be in the Diagnostic Testing
Mode. Refer to How to Enter Diagnostic Testing
Feature at the beginning of this section.
To enter, press the START (enter) keypad. The display
will show “dt x” where “x” is the custom drive type
value. Refer to Table 19.
Display
Drive Type
“dt 1”
2 HP drive
“dt 2”
3 HP drive
“dt 3”
5 HP 280V drive
“dt 4”
5 HP 480V drive
Table 19
To exit the Custom Drive Type Value, press the PERM
PRESS/60C (<) keypad. The control will return to the
Diagnostic Testing Mode.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
89
Testing Machine and Electronic Control Functions
Production Test Cycle Quick Reference Chart
Display
Test Cycle Step
Comments
“S xx”
FEC Control Software
Version
xx is the software version number.
“o xx”
Output Board Software
Version
xx is the software version number.
“Ct25”
Control Type
2.5 is the Control type.
“COIn”
Control Type
Coin
“IntL”
Control Type
International
“drAn”
Drain Type
Gravity Drain
“tEnP”
Temp Sensor
Step skipped if not model with heat.
“HEAt”
Heater
Step skipped if not heater-equipped.
“L dC”
Door Lock Type
“L dC” for 24 VDC lock.
“droP” or “drCL”
Door Status
Door open or closed.
“drUL” or “drLo”
Door Lock Status
Door will lock.
“8.8.8.8.” + all LEDs
Display Test
All display elements are lit.
“PAxx” where xx = 1-3,
5-11
Keypad Test step
Advance after all keypads are pressed.
“A xx”
Top Cover Switch Test
xx is either “CL” for closed or “oP” for open.
“U xx”
Coin Vault Switch Test
xx is either “CL” for closed or “oP” for open.
“CxCx”
Coin Drop Test
1st x is number of Coin Drop #1 coins. 2nd x is number of Coin
Drop #2 coins.
“Cxxx”
Machine Type/Size
“drxx”
Drive Software Version
Number
xx is the drive software version number. Design 2 models only.
“dPxx”
Drive Parameter Table
Version Number
xx is the drive parameter table version number. Design 2 models
only.
“dt x”
Drive Type Value
xx is the drive type value. Design 2 models only.
“HFIL”
Hot Fill to Low Level
All water outputs turned off when Low Level reached.
“CFIL”
Cold Fill to Low Level
All water outputs turned off when Low Level reached.
“bFIL”
Warm Fill to Low Level
All water outputs turned off when Low Level reached.
“bFIH”
Warm Fill to High Level
All water outputs turned off when High Level reached.
“S1” for supply or
“C2Co” for
compartment
Supply #1 or Compartment
#2 Cold Fill
“S2” for supply or
“C2Ho” for
compartment
Supply #2 or Compartment
#2 Hot Fill
“S3” for supply or
“C3Co” for
compartment
Supply #3 or Compartment
#3 Cold Fill
Table 20 (continued)
90
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Testing Machine and Electronic Control Functions
Table 20 (continued)
Production Test Cycle Quick Reference Chart
Display
Test Mode
Comments
“S4” for supply or
“C4Ho” for
compartment
Supply #4 or Compartment
#4 Hot Fill
“xxxF” degrees F or
“xxxC” degrees C
depending on the
Fahrenheit/Celsius
programming parameter
Heat water to 110°F or
display temperature
xxx is degree temperature. This step skipped if not model with
heat. Heater turned off when temperature reached.
“LoAg”
Reduced Wash Speed
Forward with no agitation
action
This step skipped on 2 Speed Models.
“Ag”
Wash Speed Forward with no
agitation action
“rAg”
Wash Speed Reverse with no
agitation action
“drAI”
Drain Distribution Speed
“PUrg”
Factory Valve Purge
“SP 1”
Extract Speed #1 “very low”
This step skipped on 2 Speed Models.
“SP 2”
Extract Speed #2 “low”
This step skipped on 2 Speed Models.
“SP 3”
Extract Speed #3 “medium”
This step skipped on 2 Speed Models.
“SP 4” (VFD Models)
or
“SPIn” (2 Speed
Models)
Extract Speed #4 “high”
“SP 5”
Extract Speed #5 “very high” This step skipped on 2 Speed and F-Speed Models.
“SP 6”
Extract Speed #6 “ultra high” Design 2 models only.
“Prdn”
End of test
Turn Power off
Table 20
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
91
Error Codes
Following is a list of possible error codes for an
electronic control. Errors beginning with “EI” refer to
external device Infra-red communication errors. Errors
beginning with “EC” refer to card reader errors. All
other errors refer to machine errors.
Display
Cause/
Corrective Action
Description
EI01
Transmission Failure
Communication failure. Re-aim external device and try
again.
EI02
Time-out Error
Communication failure. Re-aim external device and try
again.
EI03
Invalid Command Code
Communication successful, but the command was not
valid for this machine type, or the control could not
perform the command in its current mode of operation.
Ensure data is for current machine type and control is in
correct mode.
EI04
Expecting Upload Request
Communication failure. Re-aim external device and try
again.
EI05
Invalid or Out-of-Range Data
The value in at least one of the programming options is
invalid or out of range. Recheck the programming
option’s value and try again.
EI09
CRC-16 Error
Communication failure. Re-aim external device and try
again.
EI0A
Framing Error
Communication error. Re-aim external device and try
again.
EI0C
Time-out Exceeded
Communication error. Re-aim external device and try
again.
EI0E
Encryption Error
Communication error. Re-aim external device and try
again. If the problem persists, check that the security
code is correct.
EI0F
Infra-red Disabled
Communication failure or infra-red is disabled.
Manually enable infra-red on control or re-aim external
device and try again.
EC02
Time-out Error
Communication failure. Try card again.
EC03
Invalid Command Code
Communication successful, but the command was not
valid for this machine type, or the control could not
perform the command in its current mode of operation.
Ensure data is for current machine type and control is in
correct mode.
EC05
Invalid or Out-of-Range Data
The value in at least one of the programming options is
invalid or out of range. Recheck the programming
option’s value and try again.
Table 21 (continued)
92
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Error Codes
Table 21 (continued)
Display
Cause/
Corrective Action
Description
EC11
No Card Reader Initialization
Communication is valid, but there is no card reader
initialization. Power down, power up and try again.
EC18
No Communication
Card reader is initialized, communication lost. Power
down, power up and try again. If error persists, replace
control or card reader.
EC19
No Card Reader Communication
Communication failure. Power down, power up and try
again. If error persists, replace control or card reader.
E FL
Fill Error
Programmed water level not reached within 10 minutes
(or other programmed length of time) in any fill agitate
cycle. End cycle. Power down machine to clear.
E SP
SPI Communications Error
Front End control cannot communicate with output
board. Power down the machine, power up and try
again.
E dL
Door Lock Error
Door does not lock immeadiately upon closing (open
and reclose door) or doesn’t unlock 5 seconds after cycle
completion. Power down machine and retry.
E do
Door Open Error
Control detects door open. Caused by pulling on door
while locked or about to lock. Correct inoperative door
locking system. End cycle. Power down machine to
clear.
E Ub
Unbalance Error
Unable to balance load. Redistribute load and run cycle.
door
Door Open Indicator
Door is not closed in Start Mode. If door is closed, check
for improper wiring or faulty door switch.
Err
Coin Error
Invalid coin pulse or inoperative coin sensor. Check coin
drop area and remove obstructions. If error persists,
tampering may have occured. Evaluate security
procedures.
E dr
Drain Alarm Error
Machine not drained within 15 minutes (or other
programmed length of time) in any drain step. End
cycle. Power down machine to clear.
E Ht
Heat Alarm Error
Programmed heat alarm time of 120 minutes or other
programmed length of time is exceeded. Turns off heater
output for remainder of cycle.
E oP
Open Temperature Sensor Error
Control senses temperature less than 0°F (-18°C) in
machine equipped with temperature sensor. Heater and
thermistor related operations are disabled.
E SH
Shorted Temperature Sensor Error
Control senses temperature greater than 220°F (104°C)
in machine equipped with temperature sensor. Heater
and thermistor related operations are disabled for
remainder of cycle.
E ro
Rotation Sensor Error
Invalid signal received from Rotation Sensor. Control
will activate coast times to complete cycle.
Table 21 (continued)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
93
Error Codes
Table 21 (continued)
Display
Cause/
Corrective Action
Description
E FS
Frame Balance Switch Error
Control detects Frame Balance Switch open. End cycle.
E db
Drive Balance Switch Error
Control detects VFD Balance Switch input closed at
start of drain step. End cycle. Power down machine to
clear.
E Ld
Water Leak Detection Error
If control senses a drop in water level during diagnostic
testing. Power down machine to clear. If control shows
error after door is open (when cycle is completed) for
one minute or after test has been completed, lights the
right-most decimal point* on the display and the error
information will be logged in audit data.
E Sd
Slow Drain Error
If control shows error after door is open (when cycle is
completed) for one minute, lights the right-most decimal
point* on the display and the error information will be
logged in audit data.
E LF**
Water Leak Detection Error
Control senses an increase in water level during
diagnostic testing. Power down machine to clear. If
control shows error after door is open (when cycle is
completed) for one minute or after test has been
completed, lights the right-most decimal point* on the
display and the error information will be logged in audit
data.
Ed01**
SPI Communication Error
Front End control cannot communicate with motor
drive. Power down, verify input power and 6-pin
communication connection on drive and Front End
control, power up and try again.
Ed02**
DC Bus Error
The control detects the DC bus is too high. Power down,
verify line voltage is within specification, power up and
try again.
Ed03**
Tachometer Error
The drive detects the tachometer input is damaged
during power up or no tachometer signal is detected
after initiating motor output. Power down, verify H3 on
drive and tachometer connections on motor, power up
and try again.
Ed04**
Locked Rotor Error
Motor does not reach speed at startup. Power down,
verify motor mounting and look for obstructions, power
up and try again.
Ed05**
IGBT Overcurrent Error
The drive detects an overcurrent shunt condition. Power
down machine for a minimum of two minutes, verify the
motor is not shorted phase to phase or phase to ground.
Power up and try again. If problem persists, replace
drive.
*To clear the decimal point on display, press the START (enter) keypad 3 times in succession (within 5 seconds).
**Design 2 models only.
Table 21 (continued)
94
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Error Codes
Table 21 (continued)
Display
Cause/
Corrective Action
Description
Ed06**
Thermal Error
The control detects a high IPM temperature. Power
down, verify convection around drive heat sink, power
up and try again.
Ed07**
No Setup Error
The drive receives movement commands without
receiving a setup packet. Power down, power up and try
again.
Ed08**
Max Over Current Error
The drive detects motor output overcurrent condition.
Power down, power up and try again.
Ed09**
Current Sensor Error
The drive detects a current sensor is not operating
properly at startup. Power down, power up and try again.
If problem persists, replace drive.
*To clear the decimal point on display, press the START (enter) button 3 times in succession (within 5 seconds).
**Design 2 models only.
Table 21
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
95
Rapid Advance Feature
The Rapid Advance feature allows the owner to
quickly advance through active cycles or advance into
a cycle from the ready mode.
How to Enter Rapid Advance
How to Enter Rapid Advance During an
Active Cycle
1. Be certain top cover is open and coin vault switch
is closed.
2. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “rAPd” appears in
the display.
3. Press the NORMAL/40C ( ) or the PERM
PRESS/40C ( ) keypad until “rAPd” appears in
the display.
3. Press the START (enter) keypad. The display will
show cycle time and the START (enter) keypad
LED will flash.
4. Press START (enter) to activate Rapid Advance
cycle.
NOTE: Door must be closed to start cycle.
<
<
4. Press the START (enter) keypad to start cycle.
>
2. While pressing and holding the PERM PRESS/
90C keypad with one hand, press the NORMAL/
90C keypad with the other hand.
>
1. If control is in Ready Mode, control must be put
into Manual Mode. Refer to Entering the
Manual Mode.
How to Use Rapid Advance
Control may be in an active cycle or in the Ready
Mode to use the Rapid Advance feature.
While in the Rapid Advance Mode, pressing the
START (enter) keypad will advance the machine to the
next cycle step. The cycle indicator lights will tell
which cycle step the machine is in.
For Example: If the machine is in the first Fill cycle
step, pressing the START (enter) keypad will advance
the machine into the Agitate cycle step.
Continue pressing the START (enter) keypad until the
cycle is completed.
How to Exit Rapid Advance Feature
1. Advance through the cycles until reaching the
Ready Mode.
NOTE: The Rapid Advance option must be turned
on for Rapid Advance to work. Refer to option 22
in Programming Control.
96
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Clear Vend Feature
The Clear Vend feature allows the owner to clear a
control which is in the middle of satisfying a vend
price, and set it back to the Ready Mode.
How to Clear Vend
1. Open the top cover. Refer to Opening the Top
Cover.
2. While pressing and holding the PERM PRESS/
90C keypad with one hand, press the NORMAL/
60C keypad with the other hand. The control will
reset to Ready Mode.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
97
Power Fail Recovery
The Power Fail Recovery feature allows the cycle
status to be saved in memory in the event of a power
failure.
If the power failure lasted less than 2 minutes, the
cycle will resume without requiring the user to press
the START (enter) keypad to restart.
If the power failure lasted longer than 2 minutes, the
START (enter) keypad will flash until it is pressed and
the cycle will restart from the point it left off.
98
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Communications Mode
Infra-red Communications
The Infra-red Communications feature allows the
control to communicate with an external device. The
control can be programmed and have its data read
without using the keypad. It may also be used to start
and stop various diagnostic tests.
How to Begin Communications with An
External Device
Card Reader Communications
(Card Models Only)
The Card Reader Communications feature allows the
control to communicate with the card reader. The
control can be programmed for a limited number of
options and have its data read without using the
keypad.
The control will go blank and the display will show
“-C-” until the communication is complete. If an error
occurs that terminates communication, the display will
show “EIXX” (“XX” represents the error code).
NOTE: The Infra-red Communications option
must be turned on. Refer to option 15 in
Programming Control.
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
99
Default Cycles
Cycle Steps
Cycle reference
(display in Program Mode)
Agitation type
Wash 1 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 2 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 3 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 4 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
100
Cycle Chart
Perm
Normal/
Press/
40C
90C
Perm
Press/
60C
Perm
Press/
40C
Perm
Press/
70C
Perm
Press/
50C
Delicate/
30C
CYC4
CYC5
CYC6
CYC7
CYC8
CYC9
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
3/12/3
Gentle
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
2
2
2
2
2
2
2
Normal/
90C
Normal/
60C
CYC1
CYC2
CYC3
18/3/18
Normal
18/3/18
Normal
OFF
2
Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (30C)
Low
Low
Low
Low
Low
Low
Low
Low
Low
C1 (S1)
C1 (S1)
C1 (S1)
C1 (S1)
C1 (S1)
C1 (S1)
C1 (S1)
C1 (S1)
C1 (S1)
2
2
2
2
2
2
2
2
2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0
0
0
0
0
0
0
0
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
2
2
2
2
2
2
2
2
Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (40C) Warm (30C)
Low
Low
Low
Low
Low
Low
Low
Low
Low
C1
C1
C1
C1
C1
C1
C1
C1
C1
2
2
2
2
2
2
2
2
2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0
0
0
0
0
0
0
0
0
ON
ON
ON
ON
ON
ON
ON
ON
ON
6
6
6
6
6
6
6
6
3
Hot (90C)
Low
Hot (60C) Warm (40C) Hot (90C)
Low
Low
Low
Hot (60C) Warm (40C) Hot (70C)
Low
Low
Low
Hot (50C) Warm (30C)
Low
Low
C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3
(S1, S2)
(S1, S2)
(S1, S2)
(S1, S2)
(S1, S2)
(S1, S2)
(S1, S2)
(S1, S2)
(S1, S2)
2
2
2
2
2
2
2
2
2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0
0
0
0
0
0
0
0
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
2
2
2
2
2
2
2
2
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
High
High
High
Low
High
Low
Low
Low
Low
C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3
2
2
2
2
2
2
2
2
2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0
0
0
0
0
0
0
0
0
(continued)
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Default Cycles
(continued)
Cycle Steps
Cycle reference
(display in Program Mode)
Agitation type
Rinse 1 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Drain
Spin (min.)
Rinse 2 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Perm
Press/
40C
Perm
Press/
70C
Perm
Press/
50C
Delicate/
30C
CYC4
CYC5
CYC6
CYC7
CYC8
CYC9
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
3/12/3
Gentle
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
High
High
High
High
High
High
High
High
High
Normal/
60C
CYC1
CYC2
CYC3
18/3/18
Normal
18/3/18
Normal
ON
2
0
0
0
0
0
0
0
0
0
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0
0
0
0
0
0
0
0
0
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
High
High
High
High
High
High
High
High
High
C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3
Heat (if enabled)
Drain
Spin (min.)
Rinse 3 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
0
0
0
0
0
0
0
0
0
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
2
2
2
2
2
2
2
2
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
High
High
High
Low
High
High
High
High
High
C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3
Heat (if enabled)
Drain
Spin (min.) (spin speed)
Rinse 4 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
0
0
0
0
0
0
0
0
0
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
1 (High)
ON
ON
ON
ON
ON
ON
ON
ON
ON
3
3
3
3
3
3
3
3
3
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Cold
Low
Low
Low
Low
Low
Low
Low
Low
Low
C1, C2, C3, C1, C2, C3, C1, C2, C3, C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3
C4 (S3, S4) C4 (S3, S4) C4 (S3, S4) (S3, S4)
(S3, S4)
(S3, S4)
(S3, S4)
(S3, S4)
(S3, S4)
Heat (if enabled)
Drain
Spin (min.) (spin speed)
F8238301
Perm
Press/
60C
Normal/
90C
C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3 C1, C2, C3
Heat (if enabled)
Default Cycle Time
(hh:mm:ss)
Cycle Chart
Perm
Normal/
Press/
40C
90C
0
0
0
0
0
0
0
0
0
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
5 (Design 1:
Very High)
(Design 2:
Ultra High)
5 (Design 1:
Very High)
(Design 2:
Ultra High)
5 (Design 1:
Very High)
(Design 2:
Ultra High)
3 (Design 1:
Very High)
(Design 2:
Ultra High)
3 (Design 1:
Very High)
(Design 2:
Ultra High)
3 (Design 1:
Very High)
(Design 2:
Ultra High)
3 (Design 1:
Very High)
(Design 2:
Ultra High)
3 (Design 1:
Very High)
(Design 2:
Ultra High)
2
(High)
2 speed
00:27:20
00:27:20
00:27:20
00:25:20
00:25:20
00:25:20
00:25:20
00:25:20
00:21:20
F and Vspeed
(Design 1)
00:28:50
00:28:50
00:28:50
00:26:50
00:26:50
00:26:50
00:26:50
00:26:50
00:22:50
F and Vspeed
(Design 2)
00:29:02
00:29:02
00:29:02
00:27:02
00:27:02
00:27:02
00:27:02
00:27:02
00:23:02
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
101
Default Cycles
Cycle Steps
Cycle reference
(display in Program Mode)
Agitation type
Blank Cycle Chart
Perm
Normal/
Press/
40C
90C
Normal/
90C
Normal/
60C
CYC1
CYC2
CYC3
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
Perm
Press/
60C
Perm
Press/
40C
Perm
Press/
70C
Perm
Press/
50C
Delicate/
30C
CYC4
CYC5
CYC6
CYC7
CYC8
CYC9
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
3/12/3
Gentle
Wash 1 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 2 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 3 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 4 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
(continued)
102
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Default Cycles
(continued)
Cycle Steps
Cycle reference
(display in Program Mode)
Agitation type
Blank Cycle Chart
Perm
Normal/
Press/
40C
90C
Normal/
90C
Normal/
60C
CYC1
CYC2
CYC3
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
Perm
Press/
60C
Perm
Press/
40C
Perm
Press/
70C
Perm
Press/
50C
Delicate/
30C
CYC4
CYC5
CYC6
CYC7
CYC8
CYC9
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
3/12/3
Gentle
Rinse 1 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Rinse 2 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Rinse 3 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.) (spin speed)
Rinse 4 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.) (spin speed)
Default Cycle Time
(hh:mm:ss)
2 speed
F and Vspeed
(Design 1)
F and Vspeed
(Design 2)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
103
Default Cycles
Cycle Steps
Cycle reference
(display in Program Mode)
Agitation type
Blank Cycle Chart
Perm
Normal/
Press/
40C
90C
Normal/
90C
Normal/
60C
CYC1
CYC2
CYC3
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
Perm
Press/
60C
Perm
Press/
40C
Perm
Press/
70C
Perm
Press/
50C
Delicate/
30C
CYC4
CYC5
CYC6
CYC7
CYC8
CYC9
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
3/12/3
Gentle
Wash 1 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 2 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 3 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 4 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
(continued)
104
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Default Cycles
(continued)
Cycle Steps
Cycle reference
(display in Program Mode)
Agitation type
Blank Cycle Chart
Perm
Normal/
Press/
40C
90C
Normal/
90C
Normal/
60C
CYC1
CYC2
CYC3
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
Perm
Press/
60C
Perm
Press/
40C
Perm
Press/
70C
Perm
Press/
50C
Delicate/
30C
CYC4
CYC5
CYC6
CYC7
CYC8
CYC9
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
3/12/3
Gentle
Rinse 1 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Rinse 2 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Rinse 3 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.) (spin speed)
Rinse 4 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.) (spin speed)
Default Cycle Time
(hh:mm:ss)
2 speed
F and Vspeed
(Design 1)
F and Vspeed
(Design 2)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
105
Default Cycles
Cycle Steps
Cycle reference
(display in Program Mode)
Agitation type
Blank Cycle Chart
Perm
Normal/
Press/
40C
90C
Normal/
90C
Normal/
60C
CYC1
CYC2
CYC3
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
Perm
Press/
60C
Perm
Press/
40C
Perm
Press/
70C
Perm
Press/
50C
Delicate/
30C
CYC4
CYC5
CYC6
CYC7
CYC8
CYC9
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
3/12/3
Gentle
Wash 1 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 2 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 3 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Wash 4 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
(continued)
106
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F8238301
Default Cycles
(continued)
Cycle Steps
Cycle reference
(display in Program Mode)
Agitation type
Blank Cycle Chart
Perm
Normal/
Press/
40C
90C
Normal/
90C
Normal/
60C
CYC1
CYC2
CYC3
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
Perm
Press/
60C
Perm
Press/
40C
Perm
Press/
70C
Perm
Press/
50C
Delicate/
30C
CYC4
CYC5
CYC6
CYC7
CYC8
CYC9
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
18/3/18
Normal
3/12/3
Gentle
Rinse 1 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Rinse 2 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.)
Rinse 3 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.) (spin speed)
Rinse 4 (ON/OFF)
Time for agitation (min.)
Fill Temperature
Fill Level
Supply
Heat (if enabled)
Drain
Spin (min.) (spin speed)
Default Cycle Time
(hh:mm:ss)
2 speed
F and Vspeed
(Design 1)
F and Vspeed
(Design 2)
F8238301
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
107