Makita DVC340 Instruction manual

ENGLISH (Original instructions)
INSTRUCTION MANUAL
Cordless Vacuum Cleaner
DVC340
DVC350
011111
IMPORTANT: Read Before Using.
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model
DVC340
DVC350
Volume
Capacity
3.0 L
Max. Air volume
HIGH
Continuous use (Approx.)
LOW
3
3.3 m /min
3.4 m3/min
4 min (with BL1415)
6 min (with BL1815)
5 min (with BL1415N)
7 min (with BL1815N)
-
8 min (with BL1820)
10 min (with BL1430)
13 min (with BL1830)
13 min (with BL1440)
18 min (with BL1840)
-
21 min (with BL1850)
8 min (with BL1415)
12 min (with BL1815)
10 min (with BL1415N)
14 min (with BL1815N)
-
16 min (with BL1820)
20 min (with BL1430)
26 min (with BL1830)
26 min (with BL1440)
36 min (with BL1840)
-
42 min (with BL1850)
Overall length
403 mm
Net weight
2.1 kg (BL1415 / BL1415N)
2.2 kg (BL1815 / BL1815N / BL1820)
2.3 kg (BL1430 / BL1440)
2.4 kg (BL1830 / BL1840 / BL1850)
D.C. 14.4 V
D.C. 18 V
Rated voltage
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END315-1
ENA006-1
WARNING: This appliance can be used by children aged
from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
・ Read instruction manual.
Cd
Ni-MH
Li-ion
・
Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of the European
Directives, on Waste Electric and
Electronic Equipment and Batteries and
Accumulators and Waste Batteries and
Accumulators and their implementation
in accordance with national laws,
electric equipment and batteries and
battery pack(s) that have reached the
end of their life must be collected
separately and returned to an
environmentally compatible recycling
facility.
GEA006-2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
ENE017-1
Intended use
The tool is intended for collecting dry dust.
2
14.
Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
3
7.
26.
When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
29. Follow instruction for lubricating and
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
8.
9.
10.
11.
12.
13.
14.
15.
ENB117-4
CORDLESS VACUUM CLEANER
SAFETY WARNINGS
WARNING! IMPORTANT READ CAREFULLY all
safety warnings and all instructions BEFORE USE .
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
1.
Operators must be adequately instructed on
the use of this cleaner.
2.
This cleaner is not suitable for picking up
hazardous dust.
3.
This cleaner is for dry use only.
4.
This cleaner is for indoor use only.
5.
This cleaner shall be stored indoors only.
6.
Do not pick up the following materials:
−
Hot materials such as lit cigarettes or
spark/metal
dust
generated
by
grinding/cutting metal
−
Flammable materials such as gasoline,
thinner, benzine, kerosene or paint
−
Explosive materials like nitroglycerin
−
Ignitable materials such as Aluminum,
zinc, magnesium, titanium, phosphorus or
celluloid
−
Wet dirt, water, oil or the like
−
Hard pieces with sharp edges, such as
wood chips, metals, stones, glasses, nails,
pins or razors
−
Powder to clot such as cement or toner
−
Conductive dust such as metal or carbon
−
Fine particle like concrete dust
Such action may cause fire, injury and/or
property damage.
Stop operation immediately if you notice
anything abnormal.
Do not bring close to stoves or other heat
sources.
Do not block the intake hole or vent holes.
Do not leave the cleaner when battery fitted.
Remove battery from appliance when not in
use and before servicing.
Do not allow to be used as a toy. Close
attention is necessary when used by or near
children.
Use only as described in this manual. Use only
manufacturer's recommended attachments.
Do not put any object into openings. Do not
use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce
air flow.
Use extra care when cleaning on stairs.
When using the cleaner as a blower
•
always use protective goggles, a cap and
mask while operating;
•
always be sure that the cleaner is switched
off and the battery cartridge is removed
before clearing a blockage;
•
always be sure of your footing on slopes;
•
walk, never run;
•
never point the nozzle at anyone in the
vicinity;
•
Keep all nuts, bolts and screws tight to be
sure the cleaner is in safe working
condition;
•
Store the cleaner only in a dry place;
•
The operator or user is responsible for
accidents or hazzards ocurring to other
people or their property.
KEEP FOR FUTURE REFERENCE
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.
This cleaner is intended for both domestic and
commercial use, for example in hotels, schools, hospitals,
factories, shops, offices and rental businesses.
4
ENC007-8
FUNCTIONAL DESCRIPTION
IMPORTANT SAFETY
INSTRUCTIONS
•
FOR BATTERY CARTRIDGE
1.
Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5.
Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a breakdown.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ゚ C (122 ゚ F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8.
Be careful not to drop or strike battery.
9.
Do not use a damaged battery.
10. Follow your local regulations relating to
disposal of battery.
Installing or removing battery cartridge
2
3.
4.
1. Red part
2. Button
3. Battery cartridge
3
•
•
•
•
Always switch off the cleaner before insertion or
removal of the battery cartridge.
To remove the battery cartridge, withdraw it from
the cleaner while sliding the button on the front of
the cartridge as shown in the figure.
To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can see
the red part on the upper side of the button, it is not
locked completely. Insert it fully until the red part
cannot be seen. If not, it may accidentally fall out of
the cleaner, causing injury to you or someone
around you.
Do not use force when inserting the battery
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
Battery protection system
The cleaner is equipped with the protection system,
which automatically cuts off the output power for its long
service life.
The cleaner stops during operation when the cleaner
and/or battery are placed under the following situation.
This is caused by the activation of protection system and
does not show the cleaner trouble.
•
When the cleaner is overloaded:
At this time, press the "OFF" button and
remove causes of overload and then press
the "HIGH/LOW" button again to restart.
•
When battery cells get hot: (refer to the note below.)
If any operation of the "HIGH/LOW" button
and the "OFF" button, the motor will remain
stopped. At this time, stop use of the cleaner
and cool or charge the battery cartridge after
removing it from the cleaner.
Tips for maintaining maximum battery life
2.
1
011112
SAVE THESE INSTRUCTIONS.
1.
CAUTION:
Always be sure that the cleaner is switched off and
the battery cartridge is removed before adjusting or
checking function on the cleaner.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room
temperature at 10 ゚ C - 40 ゚ C (50 ゚ F - 104 ゚ F). Let a
hot battery cartridge cool down before charging it.
Charge the battery cartridge once in every six
months if you do not use it for a long period of
time.
5
When the remaining battery capacity gets low:
If any operation of the "HIGH/LOW" button
and the "OFF" button, the motor will remain
stopped. At this time, remove the battery
cartridge from the cleaner and charge it.
•
Installing dust bag
NOTE:
•
This temperature-sensitive protection is applied
only when the cleaner is used with a battery
cartridge with a star mark.
2
1. Star mark
1
1
3
4
1. Dust outlet
2. Dust bag joint
3. Pins
4. Dust bag
011113
Hold the square section of the dust bag joint and fit the
pins inside the dust bag joint to the notches in the dust
outlet of the cleaner and then insert and turn it clockwise
all the way until it stops.
011389
Switch action
1
1. HIGH/LOW
button
2. OFF button
1
1. Hook
2
011121
011114
To start the cleaner, simply press the "HIGH/LOW" button.
To switch off, press the "OFF" button. To change the
cleaner speed, press the "HIGH/LOW" button. The first
press on this button is for high speed and the second
press for low speed and then each press on this button
repeats the high/low speed cycle alternatively.
At this time, make sure that the fastener part on the dust
bag faces upward.
NOTE:
•
When the dust bag joint and the ring inside the dust
bag come off, install as follows.
(1) Align the dust bag joint with the seam of the
dust bag and install it so that its protrusion
faces upward.
ASSEMBLY
•
•
CAUTION:
Always be sure that the cleaner is switched off and
the battery cartridge is removed before carrying out
any work on the cleaner.
Any work with the battery cartridge being installed
on the cleaner may cause a personal injury or
damage to the objects around the cleaner.
1
1. Protrusion
011115
(2)
6
Tighten the ring inside the dust bag firmly so
that the pins and the ring are positioned as
shown in the figure.
Do not pull the hose to carry the cleaner. Pulling
the hose may cause deformation or damage to the
hose.
•
1. Pins
2. Ring
2
1
011116
Installing the shoulder strap
1. Shoulder strap
2. Two hooks
B
A
1
1
2
1. Dust outlet
2. Power tool
011119
Insert the "A" end of the hose to the suction opening of
the cleaner and turn it clockwise all the way until it locks.
Attach the cuff on the "B" end of the hose and then
connect it to the dust outlet of an power tool.
2
Replacing the front cuff
Change the front cuff of the hose according to the dust
outlet size of a power tool you use.
011117
Attach one end hook of the shoulder strap onto the ring in
the front of the cleaner and thrust the other end of the
strap through the band of the dust bag and then attach
the other end hook as shown in the figure.
3
1
Adjusting the shoulder strap
1. Pull out
2. For shortening
3. For extending
1
3
2
4
011120
2
To remove the front cuff, hold the hose and turn it
counterclockwise.
To mount the front cuff, turn it clockwise and then screw
it in until it stops.
011118
OPERATION
To adjust the length of the shoulder strap, pull it out to
your desired length and pull the strap in the direction of
arrow as shown in the figure.
•
Connecting the hose
•
1. Front cuff
2. Hose
3. Remove
4. Install
CAUTION:
Do not force the hose to bend it and/or stamp it.
Forcing and/or stamping the hose may cause
deformation or damage to the hose.
•
7
WARNING:
Do not use the shoulder strap when working in a
high place.
When using the cleaner as a stationary cleaner,
place it on a flat and stable surface.
Vacuum Cleaner
Operation of the cleaner with a nozzle or a
dust bag being installed
•
WARNING:
Always be sure that the cleaner is switched off
and the battery cartridge is removed before
installing or removing the nozzle or any other
attachment on the cleaner. Failure to switch off
and remove the battery cartridge may result in
serious personal injury.
NOTE:
•
Before the blower mode operation immediately
after the cleaner mode operation, remove all
remaining dust from the cleaner due to possible
blow out of dust .
Using as a blower
1
2
011122
When using the cleaner as a portable cleaner,
cross-hanging the shoulder strap before the breast is
difficult to drop the cleaner.
1. Decorative
paper
2. Saw blade
3. Base
4. Cutting depth
5. Plaster board
3
011124
Install the nozzle onto the outlet (air vent) without fail.
To install the nozzle, fit the pin protruding from the inside
of nozzle to one of the cleaner notches and then turn
the nozzle clockwise securely.
To remove the nozzle, turn counterclockwise and pull it
out.
Direct the top point of the cleaner and then switch on.
1
2
3
4
Emptying the dust bag
5
•
011123
NOTE:
•
Long cut-off decorative paper that may be
produced by plaster board cutting work depending
on the conditions of workpiece to be cut and that
may be stuffed inside the hose may cause the hose
suction blocking. When this occurs, change the
cutting depth setting of power tool to deeper depth,
which will relieve the hose suction blocking.
•
1. Outlet (air vent)
2. Nozzle
3. Pin
•
CAUTION:
When the dust bag is just new, dust may come out
of its surface. Using it a few times will minimize the
dust leak from the surface.
8
WARNING:
Always be sure that both the cleaner and a
connected power tool are switched off and the
battery cartridge is removed and the power
tool, if corded tool, is unplugged before
installing or removing the dust bag on the
cleaner and emptying the dust bag( made of
cloth). Failure to switch off, remove the battery
cartridge and unplug the connected power tool may
result in electric shock and serious personal injury.
When the dust bag is about half full, remove the
dust bag from the cleaner and pull the fastener out.
Empty the dust bag of its contents, tapping it lightly
so as to remove particles adhering to the insides
which might hamper further collection.
NOTE:
•
For the time to empty the dust bag, use a guide
line that the dust bag becomes full when
drilling about 450 holes with 6.5 mm diameter
and 40 mm depth on the concrete. A dust bag
clogged with the built up particles may reduce the
dust collection power and cause damage to the
cleaner motor.
•
MAINTENANCE
•
WARNING:
Always be sure that the cleaner is switched off and
the battery cartridge is removed before attempting
to perform inspection or maintenance.
Cleaning the filter area
CAUTION:
Attach the dust bag (made of cloth) to the dust
bag joint securely and close the fastener
completely before use. Failure to attach the dust
bag securely and close its fastener completely may
cause blow-out of dust and result in serious
personal injury.
•
CAUTION:
Do not pick up materials other than dust , such as
stone, wood chip and the like since this cleaner is
intended for dust collection. Picking up stone, wood
chip and the like may cause damage to the fan and
the cleaner.
1. Filter area
1. Dust bag joint
2. Square section
1
1
2
011127
Check and clean up the filter area in the suction inlet
regularly. Remove foreign objects which will obstruct
suction.
Cleaning
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
CAUTION:
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
011125
Pick up the square section of the dust bag joint firmly,
turn it counterclockwise and then remove the dust bag.
•
011126
Open the fastener and dispose of the dust.
•
CAUTION:
Remove all particles adhering to the fastener area.
9
OPTIONAL ACCESSORIES
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita cleaner
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Nozzles
•
Dust bags
•
Hoses
•
Front cuffs
•
Shoulder straps
•
Makita genuine battery and charger
•
NOTE:
•
Some items in the list may be included in the tool
package as standard accessories. They may differ
from country to country.
10
11
Makita Corporation
885299A6
12
www.makita.com