Sharp LC-15S1US Operating instructions

LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
TELEVISOR DE CRISTAL
LÍQUIDO
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACIÓN
MANUAL DE OPERAÇÃO
Printed in Mexico
Imprimé au Mexique
Impreso en México
Impresso no México
TINS-A857WJZZ
04P03-MMG(J)
Products that have earned the ENERGY STARb are designed to protect the
environment through superior energy efficiency.
FRANÇAIS
ESPAÑOL
LC-13S1U
LC-15S1U
LC-20S1U
PORTUGUÊS
LC-13S1U/LC-15S1U/LC-20S1U
ENGLISH
03. 12. 11
LC-13/15/20S1U(Mex)Cover
ENGLISH
LC-13S1U
LC-15S1U
LC-20S1U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please
record the TV’s model and serial numbers in the
space provided. The numbers are located at the
rear of the TV.
Model No.:
Serial No.:
U.S.A. ONLY
IMPORTANT INFORMATION
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
LC-13/15/20S1U(Mex)(E)-a
1
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a
triangle is intended to alert the
user to the presence of important operating and maintenance
(servicing) instructions in the
literature accompanying the
product.
03.12.15, 2:16 PM
IMPORTANT INFORMATION (Continued)
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment
not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40
of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries Alliance:
www.eia.org
2
LC-13/15/20S1U(Mex)(E)-a
2
03.12.15, 2:16 PM
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety
and many years of trouble-free operation of your product, please read the Important
Safety Precautions carefully before using this product.
IMPORTANT SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property
damage if improperly handled. This product has been engineered and manufactured with the highest
priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent
potential danger, please observe the following instructions when installing, operating and cleaning the
product. To ensure your safety and prolong the service life of your Liquid Crystal Television, please
read the following precautions carefully before using the product.
■ Read instructions—All operating instructions must be read and understood before the product is
operated.
■ Keep this manual in a safe place—These safety and operating instructions must be kept in a
safe place for future reference.
■ Observe warnings—All warnings on the product and in the instructions must be observed
closely.
■ Follow instructions—All operating instructions must be followed.
■ Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.
■ Power source—This product must operate on a power source specified on the specification
label. If you are not sure of the type of power supply used in your home, consult your dealer or
local power company. For units designed to operate on batteries or another power source, refer
to the operating instructions.
■ Power cord protection—The power cords must be routed properly to prevent people from
stepping on them or objects from resting on them. Check the cords at the plugs and product.
■ If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from a
SHARP service center or your dealer.
■ Overloading—Do not overload AC outlets or extension cords.
Overloading can cause fire or electric shock.
■ Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or
short internal parts. For the same reason, do not spill water or liquid on the product.
■ Servicing—Do not attempt to service the product yourself. Removing covers can expose you to
high voltage and other dangerous conditions. Request a qualified service person to perform
servicing.
■ Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and
request a qualified service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper
adjustment of controls not described in the instructions can cause damage, which often
requires extensive adjustment work by a qualified technician.
e. When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product
indicates that the product needs servicing.
■ Replacement parts—In case the product needs replacement parts, make sure that the service
person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric
shock and/or other danger.
■ Safety checks—Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product is in proper operating condition.
■ Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the
product according to the method recommended by the manufacturer.
■ Polarization—This AC adapter may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
3
LC-13/15/20S1U(Mex)(E)-a
3
03.12.15, 2:16 PM
IMPORTANT SAFETY PRECAUTIONS (Continued)
■ Cleaning—Unplug the power cord from the AC outlet before
cleaning the product. Use a damp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.
■ Water and moisture—Do not use the product near water,
such as bathtub, washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
■ Stand—Do not place the product on an unstable cart, stand,
tripod or table. Placing the product on an unstable base can
cause the product to fall, resulting in serious personal
injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product
on a wall, be sure to follow the manufacturer’s instructions.
Use only the mounting hardware recommended by the
manufacturer.
■ When relocating the product placed on a cart, it must be
moved with utmost care. Sudden stops, excessive force and
uneven floor surface can cause the product to fall from the
cart.
■ Ventilation—The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar surface,
since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in
an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s instructions are followed.
■ The Liquid Crystal panel used in this product is made of
glass. Therefore, it can break when the product is dropped
or applied with impact. Be careful not to be injured by broken
glass pieces in case the Liquid Crystal panel breaks.
■ Heat sources—Keep the product away from heat sources
such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
■ The Liquid Crystal panel is a very high technology product with 921,600 thin film transistors, giving
you fine picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your product.
4
LC-13/15/20S1U(Mex)(E)-a
4
03.12.15, 2:16 PM
IMPORTANT SAFETY PRECAUTIONS (Continued)
■ Outdoor Antenna Grounding – If an outside antenna is connected to the television equipment, be
sure the antenna system is grounded so as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna
discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
NEC—NATIONAL ELECTRICAL CODE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
■ Lightning – For added protection for this television equipment
during a lightning storm, or when it is left unattended and
unused for long period of time, unplug it from the wall outlet
and disconnect the antenna. This will prevent damage to the
equipment due to lightning and power-line surges.
■ Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
■ To prevent fire, never place any type of candle or naked
flames on the top or near the TV set.
■ To prevent fire or shock hazard, do not expose this product
to dripping or splashing. No objects filled with liquids, such
as vases, should be placed on the product.
5
LC-13/15/20S1U(Mex)(E)-a
5
03.12.15, 2:16 PM
CONTENTS
Page
IMPORTANT INFORMATION ....................................................................................................... 1, 2
DEAR SHARP CUSTOMER ............................................................................................................. 3
IMPORTANT SAFETY PRECAUTIONS ....................................................................................... 3-5
CONTENTS ....................................................................................................................................... 6
SUPPLIED ACCESSORIES ............................................................................................................. 7
PREPARATION ............................................................................................................................ 8-11
Using the Remote Control ......................................................................................................... 8
Batteries for the Remote Control .............................................................................................. 8
Removing the Terminal Cover .................................................................................................. 9
Bundling Cables with Clamp ..................................................................................................... 9
Antenna Connection ........................................................................................................... 10, 11
Power Connection .................................................................................................................... 11
DISPLAY AND CONTROL OVERVIEW .................................................................................. 12, 13
REMOTE CONTROL ...................................................................................................................... 14
EZ SETUP (WITH AUTO CLOCK SETTING) .......................................................................... 15, 16
EZ SETUP during the First Power On .............................................................................. 15, 16
SETTING THE CLOCK ............................................................................................................. 17-19
AUTO CLOCK Setting ......................................................................................................... 17, 18
MANUAL CLOCK Setting ......................................................................................................... 19
BASIC OPERATION ................................................................................................................. 20-24
TV signals in your region ........................................................................................................ 20
Turning on POWER ................................................................................................................... 21
Standby ...................................................................................................................................... 21
Switching TV/VIDEO [AV1/AV2/COMPONENT/TV] Modes ................................................... 22
Sound Volume ........................................................................................................................... 23
Listening with Headphones ..................................................................................................... 23
Changing Channels .................................................................................................................. 24
SELECTING MENU ITEMS ............................................................................................................ 25
Selecting Menu Items .............................................................................................................. 25
ADJUSTMENTS ........................................................................................................................ 26-46
Adjusting SLEEP TIMER Settings ........................................................................................... 26
Adjusting BRIGHTNESS Settings ........................................................................................... 27
Adjusting PICTURE FLIP Settings .......................................................................................... 28
Adjusting AUDIO ONLY Settings ............................................................................................ 29
Adjusting PRESET Settings .................................................................................................... 30
Adjusting LANGUAGE Settings .............................................................................................. 31
Adjusting VIDEO ADJUST Settings .................................................................................. 32, 33
Adjusting AUDIO ADJUST Settings ........................................................................................ 34
SET UP .................................................................................................................................35, 36
Adjusting BLUE SCREEN Settings ......................................................................................... 37
Adjusting CLOSED CAPTION Settings ............................................................................ 38, 39
Adjusting V-CHIP Settings ..................................................................................................40-46
CONNECTING EXTERNAL DEVICES ..................................................................................... 47-49
TROUBLESHOOTING .............................................................................................................. 50, 51
SPECIFICATIONS ........................................................................................................................... 52
DIMENSIONAL DRAWINGS .....................................................................................................53-55
CALLING FOR SERVICE ............................................................................................................... 56
LIMITED WARRANTY .............................................................................................................. 56, 57
6
LC-13/15/20S1U(Mex)(E)-a
6
03.12.15, 2:16 PM
SUPPLIED ACCESSORIES
Make sure the following accessories are provided with the product.
Remote Control
“AAA” size Battery (×2)
RRMCGA174WJSA
Antenna Cable
AC Cord
QCNWG0003CEPA
QACCDA023WJPA
Operation Manual
UADP-0212CEZZ
UADP-A044WJPZ
UBATU0026GEZZ
TINS-A857WJZZ
Cable Clamp
PORTUGUÊS
ESPAÑOL
FRANÇAIS
ENGLISH
AC Adapter
LHLDWA002WJSB
A
• AC cord enclosed in this product is an object for 110-125V. In using it on the 125-240V AC, please consult to the
following.
SHARP ELECTRONICS CORPORATION
1300 Naperville Drive, Romeoville, Illinois 60446-1091, U.S.A. TEL: 630-226-2400
7
LC-13/15/20S1U(Mex)(E)-a
7
03.12.15, 2:16 PM
PREPARATION
Using the Remote Control
■ Use the remote control by pointing it towards the remote
control sensor window on the main unit. Objects between
the remote control and sensor window may prevent proper
operation.
POWER
OPC
HEADPHONE
HEADPHONE jack
OPC indicator
POWER indicator
Cautions regarding use of the remote control
Remote control
sensor
OPC sensor
■ Do not expose the remote control to shock.
In addition, do not expose the remote control to liquid, and
do not place in an area with high humidity.
■ Do not install or place the remote control under direct
sunlight. The heat may cause deformation of the unit.
■ The remote control may not work properly if the remote
control sensor window of the main unit is under direct
sunlight or strong lighting. In such case, change the angle of
the lighting or LCD TV set, or operate the remote control
closer to the remote control sensor window.
Batteries for the Remote Control
Before using the LCD TV set for the first time, install two (“AAA” size) batteries (supplied). When the
batteries become depleted and the remote control fails to operate, replace the batteries with new
(“AAA” size) batteries.
1
2
Open the battery
cover.
Insert two (“AAA” size)
batteries.
3
Close the battery
cover.
–
+
+
–
■ Position the positive and
negative ends of the batteries
as indicated in the compartment.
■ Slide the cover while
pressing the (Y) part.
■ Engage the claw on the
cover into the battery
housing and slide shut.
Caution!
Cautions regarding batteries
Improper use of batteries can result in chemical leakage and/or explosion. Be sure to follow the instructions below.
• Place batteries with their terminals corresponding to the (+) and (–) as indicated in the compartment.
• Different types of batteries have different characteristics. Do not mix batteries of different types.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new
battery and/or cause the old battery to leak chemicals.
• Remove batteries when they become weak.
Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a
cloth.
• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.
• If the remote control will not be used for an extended period of time, remove the batteries from the
remote control.
8
LC-13/15/20S1U(Mex)(E)-a
8
03.12.15, 2:16 PM
PREPARATION (Continued)
Removing the Terminal Cover
LC-20S1U
■ Before connecting cables and cords to the rear terminals, remove the
terminal cover. Push in the tab and pull out the terminal cover carefully.
■ To mount the cover, insert the 2 hooks on the bottom of the cover
into the cabinet and press on the upper part of the terminal cover
until the tab locks in place with a click.
LC-13/15S1U
■ Before connecting cables and cords to the rear
terminals, remove the terminal cover. Push in the 2
tabs on the right side of the terminal cover and pull it
out carefully to the left.
■ To mount the cover, insert the 2 hooks on the left side
of the cover into the cabinet and press on the right part
of the cover until the tabs lock into place with a click.
Bundling Cables with Clamp
• Secure cables and cords with the supplied
cable clamp so that they do not get caught
when mounting the cover.
Cable clamp
9
LC-13/15/20S1U(Mex)(E)-a
9
03.12.15, 2:16 PM
PREPARATION (Continued)
Antenna Connection
ANTENNAS
• The antenna requirements for good color television reception are more important than those for black & white
television reception. For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connections that are provided with the various antenna
systems.
F-type connector
1. A 75-ohm system is generally a round cable with F-type
connector that can easily be attached to a terminal without
tools (not supplied).
75-ohm coaxial cable (round)
2. A 300-ohm system is a flat “twin-lead” cable that can be
attached to a 75-ohm terminal through a 300-75-ohm
adapter (not supplied).
300-ohm twin-lead cable (flat)
OUTDOOR ANTENNA CONNECTION
• Use one of the following two diagrams if you connect an outdoor antenna.
A: Using a VHF/UHF combination outdoor antenna
B: Using separate VHF and/or UHF outdoor antennas
• Connect the outdoor antenna cable lead-in to ANT. (Antenna terminal) on the rear of the TV set.
ANT.
(Antenna terminal)
A. Combination VHF/UHF Antenna
300/75-ohm
adapter
(not supplied)
VHF/UHF
antenna
VHF/UHF
antenna
or
300-ohm
twin-lead
75-ohm
coaxial cable
Antenna cable (supplied)
B. Separate VHF and/or
UHF Antennas
VHF
antenna
UHF
antenna
300-ohm
twin-lead
300-ohm
twin-lead
Combiner
(not supplied)
IN
or
OUT
75-ohm
coaxial cable
NOTICE
F-type connector
75-ohm coaxial cable
F-type connector should be finger-tightened only.
When connecting the RF cable to the TV set,
do not tighten F-type connector with tools.
If tools are used, it may cause damage to your
TV set.
(The breaking of internal circuit, etc.)
10
LC-13/15/20S1U(Mex)(E)-a
10
03.12.15, 2:16 PM
PREPARATION (Continued)
Antenna Connection (Continued)
CABLE TV (CATV) CONNECTION
• A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75ohm coaxial cable to the set, screw the 75-ohm cable to the ANT. terminal.
• Some cable TV companies offer “premium pay channels”. Since the signals of these premium pay
channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber
by the cable TV company. This converter/descrambler is necessary for normal viewing of the
scrambled channels. (Set your TV to channel 3 or 4, typically one of these channels is used. If this
is unknown, consult your cable TV company.) For more specific instructions on installing cable TV,
consult your cable TV company. One possible method of utilizing the converter/descrambler
provided by your cable TV company is explained below.
Please note: An RF switch provided with two inputs (A and B) is required (not supplied).
“A” position on the RF switch (not supplied): You can view all unscrambled channels by using the TV’s
channel keys.
“B” position on the RF switch (not supplied): You can view the scrambled channels via the converter/
descrambler by using the converter’s channel keys.
RF switch (not supplied)
Two-set
signal
splitter
(not
supplied)
OUT
Cable TV Line
IN
Cable TV converter/
descrambler
(not supplied)
A
• Consult your SHARP Dealer or Service Center for the type of splitter, RF switch or combiner that might be
required.
Power Connection
POWER INPUT
terminal (DC12V)
MAIN POWER
Household power outlet
AC adapter
AC cord
A
• Use a commercially available AC plug adapter, if necessary, depending on the design of the wall outlet.
• Always turn the MAIN POWER switch of the LCD TV set to off when connecting the AC adapter.
• Unplug the AC adapter from the product and power outlet when not using for a long period of time.
11
LC-13/15/20S1U(Mex)(E)-a
11
03.12.15, 2:16 PM
DISPLAY AND CONTROL OVERVIEW
Controls
Upper control panel
VOL (–)/(+)
CH ( )/( )
MENU
TV/VIDEO
MAIN POWER
The screen can be
adjusted backwards to an
angle between 12
degrees and 35 degrees.
The screen cannot be set
up straight. When
changing the angle, make
sure to hold the stand and
adjust the screen to the
best viewable angle.
12°
35°
Adjustable
range
Speaker
OPC sensor
HEADPHONE jack
Plug the headphone mini-plug into the HEADPHONE
jack located on the front of the TV set.
OPC indicator (Optical Picture Control)
Remote control sensor
The Optical Picture Control indicator lights up green
when the BRIGHTNESS is set to AUTO. (See page 27.)
POWER indicator
A green indicator lights when the power is on and a red
indicator lights when in the standby mode (the indicator
will not light when the main power is off).
* The examples used throughout this manual are based
on the LC-20S1U model.
A
• TV/VIDEO, CH ( )/( ), VOL (–)/(+), and MENU on the main unit have the same functions as the same buttons
on the remote control. Basically, this operation manual provides a description based on operation with the remote
control.
12
LC-13/15/20S1U(Mex)(E)-b
12
03.12.15, 2:17 PM
DISPLAY AND CONTROL OVERVIEW (Continued)
Terminals
VIDEO
AUDIO (L)
AUDIO (R)
S-VIDEO
AV-IN1
ANT. (Antenna terminal)
Y
PB
PR
COMPONENT
AUDIO (L)
AUDIO (R)
POWER INPUT
(DC12V)
Carrying handle
Round lock for Kensington
Security Standard Slot.
Stand
● The screen can be
adjusted backwards to
an angle between 12
and 35 degrees.
When changing the
angle, make sure to hold
the stand and adjust to
the best viewable angle.
*
AUDIO (R)
AUDIO (L)
AV-OUT
AV-IN2
VIDEO
S-VIDEO
(INPUT ONLY)
Be careful to prevent the
product from falling over
when adjusting the angle.
Also place the product on
a stable base.
13
LC-13/15/20S1U(Mex)(E)-b
13
03.12.15, 2:17 PM
REMOTE CONTROL
1 POWER (p. 21)
1
POWER
10
BRIGHT
11
SLEEP
2
3
4
5
6
7
PIC. FLIP
12
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
FLASHBACK
VOL
CH
Switch the Liquid Crystal Television power
on or off.
2 SLEEP (p. 26)
Set the sleep timer.
3 ENTER
Execute a command.
13
14
4 DISPLAY
15
16
5 AUDIO ONLY (p. 29)
Display the channel and time information.
Output audio without screen image.
6 MUTE (p. 23)
8
Mute the sound.
17
7 VOL (+)/(–) (p. 23)
Set the volume.
8 CH ( )/( ) (p. 24)
9
Select channel.
9 MTS (p. 23)
Select audio settings.
10 BRIGHT (p. 27)
Adjust the brightness of the screen.
11 PIC. FLIP (p. 28)
Set the orientation of the picture.
12 a/b/c/d (Cursor control) (p. 15)
Select a desired item on the screen.
13 MENU (p. 17)
Display the menu screen.
14 CC (p. 38)
Display Closed Caption subtitles.
15 TV/VIDEO (p. 22)
Select a Liquid Crystal Television input
source.
16 FLASHBACK (p. 24)
Return to the previous channel.
17 Channel Select (p. 24)
Set the channel.
14
LC-13/15/20S1U(Mex)(E)-b
14
03.12.15, 2:17 PM
EZ SETUP (WITH AUTO CLOCK SETTING)
EZ SETUP during the First Power On
■ When you turn on the TV for the first time, it will automatically
memorize the broadcasting channels and clock.
Please perform the following instructions before you press MAIN
POWER.
(1) Insert the batteries into the remote control. (See page 8.)
(2) Connect the antenna cable to the TV set. (See page 10.)
(3) Connect the AC adapter to the POWER INPUT terminal of the
product and plug in the AC cord to the wall outlet. (See page 11.)
Control section of main unit
MAIN POWER
1
Press MAIN POWER, located on
the upper side of the main unit, to
turn on the TV. The SELECT
LANGUAGE mode will be displayed.
2
Press a/b to select “ENGLISH”,
“ESPAÑOL (SPANISH)” or
“FRANCAIS (FRENCH)”, and press
ENTER.
3
POWER
Press a/b to select ON or OFF.
When you select ON, the TV set
will automatically memorize the
broadcasting channels.
SE L EC T LANGUAGE
ENGL I SH
ESPAÑOL
FRANCA I S
SELECT :
ENTER :
ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
E Z SE TUP
CH - SE T T I NG
ON
OFF
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
Press ENTER to access AUTO
CLOCK mode.
MENU
TV/VIDEO
ENTER/
a/b
FLASHBACK
VOL
4
CH
SELECT :
Press a/b to select ON or OFF.
When you select ON, the TV set
will automatically search the time
signals (EDS signals), provided by
some TV stations, to adjust the
clock. The AUTO CLOCK setting
may take from several minutes to
an hour depending on the number
of channels to receive and signal
status. If you know the channel of
the EDS signal carrier (PBS or
other) in your area, select OFF and
follow the procedure in AUTO
CLOCK Setting. (See pages 17,
18)
MENU
5
ENTER :
ENTER
E Z SE TUP
AUTO CLOCK
ON
OFF
SELECT :
ENTER :
ENTER
Press ENTER to access EZ
SETUP mode.
A
• If you select OFF in “EZ SETUP CH-SETTING”, EZ SETUP will be canceled.
15
LC-13/15/20S1U(Mex)(E)-b
15
03.12.15, 2:17 PM
EZ SETUP (WITH AUTO CLOCK SETTING) (Continued)
EZ SETUP during the First Power On (Continued)
6
POWER
Press a/b to select YES, and
press ENTER.
CONNECT ANTENNA OR CABLE.
BRIGHT
SLEEP
If you want to stop the EZ SETUP
process once it has started, press
c and it will be canceled. If you
want to SET UP again, please refer
to pages 35 and 36 on SET UP.
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b/c/d
START EZ SETUP?
YES
NO
FLASHBACK
VOL
CH
To cancel EZ SETUP
SELECT :
ENTER :
ENTER
EX I T :
MENU
Press a/b to select NO, and
press ENTER.
MENU
The tuner will automatically search
for the broadcasting and cable TV
channels. (The CH No. will automatically increase when it appears.)
PLEASE WA I T
AUTO PROGRAMMI NG
STOP :
The TV set will automatically
search for EDS signals.
PLEASE WA I T
NOW SEARCH I NG T IME
If EDS signals are received, the
channel number and time will be
displayed, and then the screen
shown in step 7 appears.
STOP :
7
Once EZ SETUP is completed, the
lowest channel number memorized
will be displayed.
2
STEREO < ON A I R
SAP
MONO
11 : 53AM
A
• Do not let the EZ SETUP screen remain unattended for a long time.
• If EZ SETUP does not memorize all the channels in your region, please refer to pages 35 and 36 for more
information on manually memorizing the channels using CHANNEL SETTING.
• It may be difficult to preset when the broadcasting signals are weak, the channel cycle frequency is incorrect or
the frequency jamming is occurring around the area. Please refer to pages 35 and 36 for more information on
manually memorizing channels using CHANNEL SETTING.
• If there are no channels with EDS signals or the antenna signal is weak, the AUTO CLOCK Setting may not
operate. In this case, a “EDS CH IS NOT AVAILABLE” message will display and the mode will change to MANUAL
CLOCK Setting. Refer to page 19 to set the clock manually.
16
LC-13/15/20S1U(Mex)(E)-b
16
03.12.15, 2:17 PM
SETTING THE CLOCK
AUTO CLOCK Setting
There are two methods of setting the clock: AUTO CLOCK and MANUAL CLOCK. AUTO CLOCK uses
EDS signals, which are provided by some TV stations, to automatically adjust the clock. MANUAL CLOCK
set the clock manually in areas where no channel carries EDS signals.
POWER
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
SET UP, and press ENTER.
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b
FLASHBACK
VOL
CH
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
MENU
3
Press a/b to move the cursor to
CLOCK, and press ENTER.
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
CLOCK
SELECT :
4
Press a/b to move the cursor to
AUTO CLOCK, and press ENTER.
ENTER : ENTER
CLOCK
RETURN
AUTO CLOCK
MANUAL CLOCK
OFF
SELECT :
ENTER : ENTER
A
• The CLOCK can be stopped completely by setting CLOCK to “OFF”.
Time reset for power outage, AC adapter disconnected
If the TV has a power outage or the AC adapter cord is disconnected, the time display will have to
be reset. In that case, refer to SETTING THE CLOCK on pages 17 to 19.
17
LC-13/15/20S1U(Mex)(E)-b
17
03.12.15, 2:17 PM
SETTING THE CLOCK (Continued)
AUTO CLOCK Setting (Continued)
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
Press a/b to move the cursor to
EDS CH SET, and press ENTER.
6
Press c/d to select AUTO or
MANUAL.
7
Press a/b to move the cursor to
START, and press ENTER.
AUTO CLOCK
RETURN
EDS CH SET [AUTO ]
EDS CH
[ ––– ]
START
MENU
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
5
CH
ADJUST :
MENU
ENTER : ENTER
EX I T :
MENU
PLEASE WA I T
NOW SEARCH I NG T IME
● If you do not know the channel that
carries EDS signals in your area,
select EDS CH SET to AUTO and
select START. If you know the
channel of the EDS signal carrier in
your area, select EDS CH SET to
MANUAL. Set the EDS CH and
select START.
● When set to “AUTO CLOCK”, the
time is acquired automatically when
MAIN POWER is turned OFF. (This
function will not work when EDS
CH is not set.)
STOP :
2
STEREO < ON A I R
SAP
MONO
11 : 53AM
A
• CLOCK: The AUTO CLOCK Setting may take from several minutes to an hour depending on the number of
channels to receive and signal status.
• If there are no channels with EDS signals or the antenna signal is weak, the AUTO CLOCK Setting may not
operate. In this case, an “EDS CH IS NOT AVAILABLE” message will display, and the MANUAL CLOCK Setting
screen appears. Refer to MANUAL CLOCK Setting on page 19 to set the clock manually.
• If you know the Channel of the EDS signal carrier in your area, set EDS CH SET to MANUAL and select START.
In case, the message “EDS CH (XXX) EDS DATA IS NOT AVAILABLE” displays, set EDS CH SET to AUTO when
the AUTO CLOCK Setting screen appears.
• If broadcasting channels are not memorized, EDS signals cannot be received even when the EDS CH SET is set
to AUTO. In this case, try EZ SETUP again. (See page 35.)
18
LC-13/15/20S1U(Mex)(E)-b
18
03.12.15, 2:17 PM
SETTING THE CLOCK (Continued)
MANUAL CLOCK Setting
If there are no channels with EDS signals, set the clock manually using MANUAL CLOCK.
POWER
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
SET UP, and press ENTER.
3
Press a/b to move the cursor to
CLOCK, and press ENTER.
4
Press a/b to move the cursor to
MANUAL CLOCK, and press
ENTER.
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
MENU
CC
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
CH
MENU
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
CLOCK
CLOCK
RETURN
AUTO CLOCK
MANUAL CLOCK
OFF
SELECT :
5
Press a/b to move the cursor to
TIME, and press ENTER.
6
Press c/d to set the time, and
press ENTER.
12:00AM
11:59PM
EX I T :
MENU
EX I T :
MENU
MANUAL CLOCK
RETURN
T IME [ 12: 0 0AM]
DST
[OFF ]
11:59AM
12:00PM
A
• Make sure to press ENTER after
adjusting the time. Otherwise, the time
will not be set.
• When DST is set to ON, the time
entered is forwarded by 1 hour.
7
ENTER : ENTER
ADJUST :
ENTER : ENTER
Press MENU to return to the main
screen.
Daylight Saving-Time (DST) Adjustment
The Daylight Saving-Time changes as shown below, set the DST to ON to forward the clock by 1
hour. To rewind the clock by 1 hour, set the DST to OFF.
(Spring)
(Autumn)
On the first Sunday in April D.S.T. starts.
On the last Sunday in October D.S.T. finishes.
1:00AM
2:00AM
1:00AM
Advances 1 hour.
3:00AM
4:00AM
2:00AM
Rewinds 1 hour.
1:00AM
2:00AM
19
LC-13/15/20S1U(Mex)(E)-b
19
03.12.15, 2:17 PM
BASIC OPERATION
TV signals in your region
This product is factory set to comply with the TV broadcasting system in the United States. For Brazil,
Argentina and Uruguay, set the color system according to the country before using this product by
following the table below.
■ LC-13S1U, LC-15S1U
The VIDEO INPUT mode is compatible with color systems worldwide and is automatically set.
Country
TV broadcasting
system
Factory setting of color system
User setting
TV
Video
TV
U.S.A.
Color: NTSC
TV ch: US ch
NTSC (N358)
US ch
World Multi
Auto System
Not required or N/A
Canada, Mexico,
Latin America
Color: NTSC
TV ch: US ch
NTSC (N358)
US ch
World Multi
Auto System
Not required or N/A
Brazil
Color: PAL-M
TV ch: US ch
NTSC (N358)
US ch
World Multi
Auto System
Set color system to
PAL-M (see page 33)
Argentina,
Uruguay
Color: PAL-N
TV ch: US ch
NTSC (N358)
US ch
World Multi
Auto System
Set color system to
PAL-N (see page 33)
The World Multi Auto System
is compatible with all color
systems indicated below.
1
2
3
4
5
6
7
N358
N443
PAL
PAL-M
PAL-N
SECAM
PAL-60
■ LC-20S1U
Country
TV broadcasting
system
Factory setting of color system
User setting
TV
Video
TV/Video
U.S.A.
Color: NTSC
TV ch: US ch
NTSC (N358)
US ch
NTSC (N358)
US ch
Not required or N/A
Canada, Mexico,
Latin America
Color: NTSC
TV ch: US ch
NTSC (N358)
US ch
NTSC (N358)
US ch
Not required or N/A
Brazil
Color: PAL-M
TV ch: US ch
NTSC (N358)
US ch
NTSC (N358)
US ch
Set color system to
PAL-M (see page 33)
Argentina,
Uruguay
Color: PAL-N
TV ch: US ch
NTSC (N358)
US ch
NTSC (N358)
US ch
Set color system to
PAL-N (see page 33)
A
• The 3 Dimensional Y/C separation circuit* only works when the color system is set to N358 in TV mode and Video
mode.
*The 3 Dimensional Y/C separation circuit is used to remove flickering and color bleeding.
*The 3 Dimensional Y/C separation circuit does not function when S-VIDEO or COMPONENT signals are played.
20
LC-13/15/20S1U(Mex)(E)-b
20
03.12.15, 2:17 PM
BASIC OPERATION (Continued)
Turning on POWER
Control section of main unit
1
MAIN POWER
2
Press MAIN POWER, located on
the upper side of the main unit, to
on.
▼ On-screen display
2
The POWER indicator instantaneously changes from red to green
and the main unit turns on.
A
• The On-screen indicator disappears after a
few seconds.
STEREO
SAP
MONO
Notes:
POWER indicator
Standby
To turn off the LCD TV
POWER
Press POWER on the remote control.
The POWER indicator turns red.
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
FLASHBACK
VOL
To turn the LCD TV back on
TV/VIDEO
POWER
CH
Press POWER again.
The POWER indicator turns green.
21
LC-13/15/20S1U(Mex)(E)-b
21
03.12.15, 2:18 PM
BASIC OPERATION (Continued)
Switching TV/VIDEO [AV1/AV2/COMPONENT/TV] Modes
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
Turn on the power of the connected video equipment.
2
Press TV/VIDEO and select the
applicable input source. The
screen displays AV1, AV2, COMPONENT or TV mode each time
TV/VIDEO is pressed.
AV1 mode
AV 1
TV/VIDEO
FLASHBACK
VOL
1
CH
TV/VIDEO
A
• The AV input mode indication remains
AV2 mode
for 3 seconds.
• AV1: Video equipment connected to the
AV-IN1 input terminals.
The S-video input terminal is
additionally provided for the AVIN1 input. If both the S-video
terminal and normal video
terminals are connected with
cables, the S-video input terminal
takes priority.
.
AV 2
• AV2: AV2 mode is used to adjust the
COMPONENT mode
preset settings and IN or OUT
COMPONE N T
can be selected. AV2 indication is
not displayed when OUT is
selected. (For details on setting
AV2 IN/OUT, see page 30.)
The S-video input terminal is
additionally provided for the AVIN2 input. If both the S-video
terminal and normal video
terminals are connected with
cables, the S-video input terminal
takes priority, only when IN is
TV mode
selected for S-video.
12
• COMPONENT:
Video equipment connected to the
COMPONENT input terminals.
Playback from 480 progressive
output equipment is available.
STEREO < ON A I R
SAP
MONO
22
LC-13/15/20S1U(Mex)(E)-b
22
03.12.15, 2:18 PM
BASIC OPERATION (Continued)
Sound Volume
POWER
1
Press VOL (+) to increase the sound
volume. The bar indicator shifts right.
POWER
VOLUME
50
BRIGHT
SLEEP
2
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
FLASHBACK
VOL
Press VOL (–) to decrease the sound
volume. The bar indicator shifts left.
VOLUME
10
MUTE
CH
To mute the sound
VOL
(+)/(–)
1
Press MUTE to temporarily turn off
the sound.
is displayed for
The MUTE mark
4 seconds.
2
Press MUTE or VOL (+)/(–) to turn
the sound back to the previous level.
The mute function is automatically
turned off when any of the following
buttons are pressed: POWER,
VOL (+)/(–) or MTS.
MTS
VOLUME
30
To select MTS (Multichannel TV Sound)
1
Press MTS to display the MTS
screen.
2
Press MTS
settings.
STEREO:
SAP:
MONO:
2
to select the MTS
stereo audio
secondary audio program
monophonic audio
A
• <ON AIR appears when a STEREO or SAP
broadcast is being aired.
STEREO < ON A I R
SAP
MONO
Listening with Headphones
■ Plug the headphone mini-plug into the HEADPHONE jack located on the front of the TV set.
▼ On-screen display
Headphones
VOLUME
20
Adjust the sound volume
using VOL (e)/(f).
A
• Headphones are not included in the supplied accessories.
• No sound is heard from the main unit speakers when a headphone mini-plug is connected into the HEADPHONE
jack.
23
LC-13/15/20S1U(Mex)(E)-b
23
03.12.15, 2:18 PM
BASIC OPERATION (Continued)
Changing Channels
Changing channels by using Channel Select on the remote control.
• This LCD TV set allows you to select up to 125 channels (1 to 125). To select a channel, enter a 2or 3-digit number.
To select a 1- or 2-digit channel
number (e.g., Channel 5):
Complete the following procedure
within 4 seconds.
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
FLASHBACK
VOL
CH
CH
( )/( )
FLASHBACK
1
2
Press the
Press the
0–
5
button.
5
button.
A
• When selecting a 1-digit channel
number, do not fail to press the
button first.
Channel
Select
To select a 3-digit channel number
(e.g., Channel 115):
Complete the following procedure
within 4 seconds.
1
2
3
Press the
button.
Press the
button.
Press the
5
1––
1 1–
1 15
button.
A
• The 3-digit channel number can be
selected only when the receiving mode is
set to CABLE in CH-SETTING. (For details
on setting the receiving mode, see page
35.)
• Press FLASHBACK to show the previous
channel.
Changing channels with CH (
Air
)/(
) on the remote control
Press CH ( ) and the channels change in the
2 → 3 → . . . → 68 → 69 → 2 → 3 → . . .
Press CH ( ) and the channels change in the
3 → 2 → 69 → 68 → . . . → 3 → 2 → . . .
Cable Press CH ( ) and the channels change in the
1 → 2 → 3 → . . . → 125 →1 → 2 → 3 → . . .
Press CH ( ) and the channels change in the
3 → 2 → 1 → 125 → . . . → 3 → 2 → 1 → . . .
order shown below:
order shown below:
order shown below:
order shown below:
24
LC-13/15/20S1U(Mex)(E)-b
24
03.12.15, 2:18 PM
SELECTING MENU ITEMS
Selecting Menu Items
• This LCD TV set allows you to adjust the various settings using the menu screen. Select the desired
menu item by following the steps below and then refer to the indicated page for details.
Press MENU to display the MENU
screen.
2
Press a/b to select the desired
menu item, and press ENTER.
3
Press MENU to exit.
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b
(Page 26)
1
SELECT :
FLASHBACK
VOL
SLEEP T IMER
RETURN
SLEEP T IMER [ ––– REMA I N ]
ENTER :
ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
(Pages 32–34)
CH
MENU
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
AV ADJUST
RETURN
V I DEO ADJUST
AUD I O ADJUST
SELECT :
SELECT :
ENTER : ENTER
EX I T :
ENTER : ENTER
(Pages 27–30)
MENU
A
• The displayed items differ depending
on the setting conditions.
• The selected item changes to yellow.
• Items in magenta cannot be selected.
• TV mode
This product is factory set to comply
with the color system in the United
States (NTSC-N358). For Brazil
(PAL-M), Argentina (PAL-N) and
Uruguay (PAL-N), set the color
system before using this product.
• To return to the previous screen,
select RETURN.
• You can adjust some settings with the
special buttons: SLEEP, BRIGHT,
PIC. FLIP, AUDIO ONLY and CC (see
pages 26–29, 38 and 39).
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
MTS
[ STEREO]
AUTO POWER OFF [ OFF
]
P I CTURE F L I P
[ NORMAL ]
AV2 I N / OUT
[ IN
]
AUD I O ONLY
[ OFF
]
SELECT :
ENTER : ENTER
(Page 38 and 39)
CLOSED CAPT I ON
RETURN
CC / TEXT [ OFF ]
SELECT :
ENTER :
ENTER
(Pages 40–46)
I NPUT SECRET NO .
– – – –
(Pages 17–19, 31 and 35–37)
SET UP
RETURN
BLUE SCREEN [ OF F]
LANGUAGE
CH–SETT I NG
CLOCK
* The illustrations and on-screen displays in this operation manual are for
explanation purposes and may vary slightly from the actual operations.
SELECT :
ENTER : ENTER
EX I T :
MENU
25
LC-13/15/20S1U(Mex)(E)-b
25
03.12.15, 2:18 PM
ADJUSTMENTS
Adjusting SLEEP TIMER Settings
You can set the SLEEP TIMER to automatically turn off the TV.
Directly setting the SLEEP TIMER
POWER
1
Press SLEEP to display the SLEEP
TIMER screen.
2
Press SLEEP to set the sleep timer
(in minutes).
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
SLEEP
FLASHBACK
VOL
CH
---
30
150
120
60
––– REMA I N
90
(minutes)
The SLEEP TIMER is turned off
when --- is displayed.
A
• The SLEEP TIMER screen automatically
disappears in 3 seconds.
60 REMA I N
Setting the SLEEP TIMER on the
MENU screen
POWER
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
SLEEP TIMER.
3
Press ENTER to display the
SLEEP TIMER screen, and press
ENTER.
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
CH
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
MENU
4
Press c/d to set the sleep timer
(in minutes), and press ENTER.
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
SLEEP T IMER
RETURN
SLEEP T IMER [ ––– REMA I N ]
The time can be set in increments
of 30 minutes and in the range
between 30 and 150 minutes.
The SLEEP TIMER is turned off
when --- is displayed.
5
Press MENU to return to the main
screen.
SELECT :
ENTER : ENTER
SLEEP T IMER
RETURN
SLEEP T IMER [ –60 REMA I N ]
A
• After you set the SLEEP TIMER, pressing MAIN POWER on the TV set or POWER on the remote control will
cancel the SLEEP TIMER setting.
• 5 minutes before the SLEEP TIMER turns off the TV, 5 REMAIN is displayed on the screen for 4 seconds. The
SLEEP TIMER counts down and shows a similar 4-second display for each remaining minute until the timer turns
off the TV.
26
LC-13/15/20S1U(Mex)(E)-c
26
03.12.15, 2:19 PM
ADJUSTMENTS (Continued)
Adjusting BRIGHTNESS Settings
You can adjust the brightness of the screen.
Directly setting the BRIGHTNESS
1
Press BRIGHT to display the
BRIGHTNESS screen.
2
Press BRIGHT to change the
setting.
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
BRIGHT
MENU
BRIGHT
AUTO
TV/VIDEO
FLASHBACK
VOL
NORMAL
DARK
BR I GHTNESS [ BR I GHT ]
CH
A
• The BRIGHTNESS screen automatically
disappears in 3 seconds.
• [BRIGHT]: maximum brightness
[NORMAL]: 60% brightness (Suitable for
viewing in a well-lit area.
Saves energy.)
[DARK]:
10% brightness (Sufficiently
bright when viewing in dim
areas.)
[AUTO]:
Screen brightness adjusts
according to the ambient light
of the room to conserve power
consumption. OPC indicator
lights up green.
• When set to “AUTO”, make sure no object
obstructs the OPC sensor, which could
affect its ability to sense surrounding light.
Setting the BRIGHTNESS on the
MENU screen
POWER
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
PRESET, and press ENTER.
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
ENTER/
a/b/c/d
FLASHBACK
VOL
CH
SELECT :
MENU
3
Press a/b to move the cursor to
BRIGHTNESS, and press ENTER.
4
Press c/d to change setting, and
press ENTER.
5
Press MENU to return to the main
screen.
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
MTS
[ STEREO ]
]
AUTO POWER OFF [ OFF
P I CTURE FL I P
[ NORMAL ]
AV2 I N / OUT
[ IN
]
AUD I O ONLY
[ OFF
]
ADJUST :
ENTER : ENTER
27
LC-13/15/20S1U(Mex)(E)-c
27
03.12.15, 2:19 PM
ADJUSTMENTS (Continued)
Adjusting PICTURE FLIP Settings
You can set the orientation of the picture.
Directly setting the PICTURE FLIP
1
Press PIC. FLIP to display the
PICTURE FLIP screen.
2
Press PIC. FLIP to change the
setting.
POWER
BRIGHT
SLEEP
PIC. FLIP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
ABC
P I CTURE F L I P [NORMAL ]
MENU
NORMAL
TV/VIDEO
MIRROR
ROTATE
UPSIDE DOWN
FLASHBACK
VOL
CH
A
• The PICTURE FLIP screen automatically
disappears in 3 seconds.
• [NORMAL]: normal image
[MIRROR]: mirror image
[ROTATE]: rotated image
[UPSIDE DOWN]: upside down image
CBA
]RORR I M [ P I L F E RU T C I P
P I CTURE F L I P [ ROTATE ]
ABC
P I CTURE F L I P [ UPS I DE DOWN]
ABC
Setting the PICTURE FLIP on the
MENU screen
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
FLASHBACK
VOL
ENTER/
a/b/c/d
CH
MENU
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
PRESET, and press ENTER.
3
Press a/b to move the cursor to
PICTURE FLIP, and press
ENTER.
4
Press c/d to select the desired
picture flip setting, and press
ENTER.
5
Press MENU to return to the main
screen.
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
28
28
EX I T :
MENU
EX I T :
MENU
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
MTS
[ STEREO ]
]
AUTO POWER OFF [ OFF
P I CTURE FL I P
[ NORMAL ]
AV2 I N / OUT
[ IN
]
AUD I O ONLY
[ OFF
]
ADJUST :
LC-13/15/20S1U(Mex)(E)-c
ENTER : ENTER
03.12.15, 2:19 PM
ENTER : ENTER
ADJUSTMENTS (Continued)
Adjusting AUDIO ONLY Settings
When listening to music from a music program, you can set the Liquid Crystal display off and enjoy audio
only.
Directly setting the AUDIO ONLY
1
Press AUDIO ONLY. “PRESS
“AUDIO ONLY” FOR VIDEO
OFF” displays.
2
Press AUDIO ONLY again and
the screen image will disappear.
3
Press AUDIO ONLY again and
the screen image will reappear.
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
AUDIO
ONLY
FLASHBACK
VOL
CH
AUD I O ONLY [OFF]
PRESS “AUD IO ONLY” FOR V I DEO OFF
A
• The AUDIO ONLY screen automatically disappears in 10 seconds.
• Image screen will reappear by
pressing any key, except VOL k/l,
MUTE or MTS.
[OFF]: Both screen images and audio
are output.
[ON ]: Audio is output without screen
image.
Setting the AUDIO ONLY on the
MENU screen
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b/c/d
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
PRESET, and press ENTER.
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
FLASHBACK
VOL
CH
SELECT :
MENU
3
Press a/b to move the cursor to
AUDIO ONLY, and press ENTER.
4
Press c/d to select ON, and
press ENTER.
5
Press MENU to return to the main
screen.
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
MTS
[ STEREO ]
]
AUTO POWER OFF [ OFF
P I CTURE FL I P
[ NORMAL ]
AV2 I N / OUT
[ IN
]
AUD I O ONLY
[ ON
]
ADJUST :
ENTER : ENTER
29
LC-13/15/20S1U(Mex)(E)-c
29
03.12.15, 2:19 PM
ADJUSTMENTS (Continued)
Adjusting PRESET Settings
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
PRESET, and press ENTER.
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
FLASHBACK
VOL
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
ENTER/
a/b/c/d
SELECT :
CH
MENU
3
Press a/b to move the cursor to
the desired item, and press
ENTER.
4
Press c/d to change the setting,
and press ENTER.
5
Press MENU to return to the main
screen.
Selected item
Factory setting
BRIGHTNESS
[BRIGHT]
MTS*
[STEREO]
AUTO POWER OFF
(only TV mode)
[OFF]
PICTURE FLIP
[NORMAL] Normal image
orientation
Maximum brightness
Stereo audio
This feature is inactive.
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
PRESET
RETURN
BR I GHTNESS
[ BR I GHT ]
MTS
[ STEREO ]
AUTO POWER OFF [ OFF
]
P I CTURE FL I P
[ NORMAL ]
AV2 I N / OUT
[ IN
]
AUD I O ONLY
[ OFF
]
ADJUST :
ENTER : ENTER
Setting options
[NORMAL] Brightness 60% → Suitable for viewing in a well-lit area.
Saves energy.
[DARK]
Brightness 10% → Sufficiently bright when
viewing in dim areas.
[AUTO]
Screen brightness adjusts according to the ambient
light of the room.
[SAP]
[MONO]
Secondary audio program
Monophonic audio
[ON]
The power of the LCD TV set is turned off when there is
no signal for 5 minutes.
[MIRROR] Mirror image
→ To display mirror images for special uses.
CBA
ABC
[ROTATE] Rotated image → To display rotated images for special
uses.
ABC
[UPSIDE DOWN] Upside down image
→ To display images upside
down for special uses.
ABC
AV2 IN/OUT
[IN] AV-IN2 terminals selected
as input terminals
[OUT
[OUT
AUDIO ONLY
[OFF]
This feature is inactive.
[ON]
] Line Output is selected, Output volume is fixed, Speaker
output is available.
] Line Output is selected, Output volume is variable,
Speaker output is Mute.
Audio is output without screen image.
* In AV1, AV2 or COMPONENT mode, MTS displayed in magenta cannot be selected.
30
LC-13/15/20S1U(Mex)(E)-c
30
03.12.15, 2:19 PM
ADJUSTMENTS (Continued)
Adjusting LANGUAGE Settings
The language for the On-Screen Display can be ENGLISH, SPANISH or FRENCH.
1
Press MENU to display the MENU
screen.
POWER
BRIGHT
SLEEP
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b
FLASHBACK
VOL
SELECT :
2
CH
Press a/b to move the cursor to
SET UP, and press ENTER.
MENU
Press a/b to move the cursor to
LANGUAGE, and press ENTER.
5
Press a/b to select the language, and press ENTER.
MENU
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
CLOCK
SELECT :
4
EX I T :
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
3
ENTER : ENTER
ENTER : ENTER
LANGUAGE
RETURN
ENGL I SH
ESPAÑOL
FRANCA I S
Press MENU to return to the main
screen.
SELECT :
ENTER : ENTER
31
LC-13/15/20S1U(Mex)(E)-c
31
03.12.15, 2:19 PM
ADJUSTMENTS (Continued)
Adjusting VIDEO ADJUST Settings
Video adjustments have different selection items depending on TV mode or AV mode (signal from an
external device). (See page 33.)
1
Press MENU to display the MENU
screen.
POWER
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
ENTER : ENTER
SELECT :
2
CH
Press a/b to move the cursor to
AV ADJUST, and press ENTER.
MENU
Press a/b to move the cursor to
VIDEO ADJUST, and press
ENTER.
ENTER : ENTER
Press a/b to move the cursor to
the desired item, and press
ENTER.
ENTER : ENTER
V I DEO
RETURN
P I CTURE
T I NT
COLOR
BLACK LEVEL
SHARPNESS
RED - BLUE
GREEN
COLOR SYSTEM
RESET
SELECT :
5
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
AV ADJUST
RETURN
V I DEO ADJUST
AUD I O ADJUST
SELECT :
4
MENU
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
3
EX I T :
ADJUST ( TV )
[
50 ]
[
0]
[
0]
[
0]
[
0]
[
0]
[
0]
[ N358 ]
ENTER : ENTER
Press c/d to change the setting.
A
• See page 33 for the settings.
6
Press MENU to return to the main
screen.
RETURN
P I CTURE
50
–
SELECT :
+
ADJUST :
A
• Selecting RESET will return all settings to the factory settings.
32
LC-13/15/20S1U(Mex)(E)-c
32
03.12.15, 2:19 PM
EX I T :
MENU
ADJUSTMENTS (Continued)
Adjusting VIDEO ADJUST Settings (Continued)
TV mode
Selected item
Press c
Press d
PICTURE
Decrease contrast
Increase contrast
TINT
Toward purple
Toward green
COLOR
Lower color intensity
Higher color intensity
BLACK LEVEL
Less brightness
More brightness
SHARPNESS
Soft picture
Sharp picture
RED-BLUE
Stronger red
Stronger blue
GREEN
Weaker green
Stronger green
N358
COLOR SYSTEM
PAL-M
PAL-N
AV/COMPONENT mode
Selected item
Press c
Press d
PICTURE
Decrease contrast
Increase contrast
TINT
Toward purple
Toward green
COLOR
Lower color intensity
Higher color intensity
BLACK LEVEL
Less brightness
More brightness
SHARPNESS
Soft picture
Sharp picture
RED-BLUE
Stronger red
Stronger blue
GREEN
Weaker green
Stronger green
COLOR SYSTEM*
(AV1/AV2)
■
LC-13S1U/LC-15S1U
• Press c/d to select the COLOR SYSTEM.
LC-20S1U
• Press c/d to select the COLOR SYSTEM.
■
* COMPONENT mode has no COLOR SYSTEM.
A
• In BLUE SCREEN, AV ADJUST settings displayed in magenta cannot be selected.
• Selecting RESET will return all settings to the factory settings. (See page 32.)
• TV mode
This product is factory set to comply with the color system in the United States (NTSC-N358). For Brazil (PAL-M),
Argentina (PAL-N) or Uruguay (PAL-N), adjust the color system before using this product.
■ LC-13S1U/LC-15S1U
• COLOR SYSTEM
When you set COLOR SYSTEM to AUTO, the AUTO mode automatically detects the receiving signal system and
adjusts the reception system of the TV set.
When the picture or sound is not stable, set a specific COLOR SYSTEM (not AUTO). The picture and sound may
be improved.
33
LC-13/15/20S1U(Mex)(E)-c
33
03.12.15, 2:19 PM
ADJUSTMENTS (Continued)
Adjusting AUDIO ADJUST Settings
You can adjust the sound quality to your preference with the following settings.
POWER
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
AV ADJUST, and press ENTER.
BRIGHT
SLEEP
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
PIC. FLIP
ENTER
DISPLAY
MUTE
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
ENTER : ENTER
SELECT :
3
CH
Press a/b to move the cursor to
AUDIO ADJUST, and press
ENTER.
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
AV ADJUST
RETURN
V I DEO ADJUST
AUD I O ADJUST
MENU
SELECT :
4
Press a/b to move the cursor to
the desired item, and press
ENTER.
ENTER : ENTER
AUD I O ADJUST ( TV)
RETURN
TREBLE
BASS
BALANCE
RESE T
[
[
[
ENTER : ENTER
SELECT :
5
Press c/d to change the setting.
6
Press MENU to return to the main
screen.
0]
0]
0]
RETURN
TREBLE
0
–
SELECT :
+
ADJUST :
Selected item
Press c
Press d
TREBLE
For weaker treble
For stronger treble
BASS
For weaker bass
For stronger bass
BALANCE
Decrease audio from the
right speaker
L
R
Decrease audio from the
left speaker
A
• Selecting RESET will return all settings to the factory settings.
34
LC-13/15/20S1U(Mex)(E)-c
34
03.12.15, 2:20 PM
ADJUSTMENTS (Continued)
SET UP
■ EZ SETUP
When you move to an area with different broadcasting signals the set will automatically memorize
the channel number and time by executing EZ SETUP again. Follow steps 1-3 below, select EZ
SETUP, and then go to step 3 on page 15.
■ SETTING THE AIR/CABLE
It is necessary to set the receiving mode to AIR or CABLE channels to receive locally broadcast TV
programs.
POWER
BRIGHT
SLEEP
1
Switch the screen to TV mode and
press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
SET UP, and press ENTER.
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b
FLASHBACK
VOL
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SELECT :
3
CH
MENU
Press a/b to move the cursor to
CH-SETTING, and press ENTER.
A
• When the screen is not in TV mode,
CH-SETTING is displayed in magenta
and not selectable.
Press a/b to move the cursor to
AIR/CABLE, and press ENTER.
6
Press a/b to move the cursor to
the desired mode, and press
ENTER.
MENU
ENTER :
ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
CH–SETT I NG
RETURN
EZ SETUP
A I R/ CABLE
CH SEARCH
CH MEMORY
SELECT :
5
EX I T :
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
CLOCK
SELECT :
4
ENTER : ENTER
ENTER : ENTER
A I R / CABLE
RETURN
AIR
CABLE
Press MENU to return to the main
screen.
SELECT :
A
• Receivable channels of your TV set are:
AIR channels:
VHF: 2 through 13.
UHF: 14 through 69.
ENTER : ENTER
CABLE channels:
1 (HRC and IRC)
2 through 125 (STD, HRC and IRC)
35
LC-13/15/20S1U(Mex)(E)-c
35
03.12.15, 2:20 PM
ADJUSTMENTS (Continued)
SET UP (Continued)
■ Saving broadcast TV channels in the memory
1
Press MENU to display the MENU
screen, press a/b to move the
cursor to SET UP, and press
ENTER.
2
Press a/b to move the cursor to
CH-SETTING, and press ENTER.
3
Press a/b to move the cursor to
CH SEARCH, and press ENTER.
4
Press d. The tuner will search
through all available channels in
your area and add them to the TV
memory.
POWER
BRIGHT
SLEEP
PIC. FLIP
ENTER
DISPLAY
MUTE
AUDIO
ONLY
MENU
CC
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
CH
MENU
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
CLOCK
CH–SETT I NG
RETURN
EZ SETUP
A I R/ CABLE
CH SEARCH
CH MEMORY
CH SEARCH
AIR
A
• To interrupt CH SEARCH, press c.
CH SEARCH will stop at the current
channel and will not add any higher
channels.
2
START :
EX I T :
MENU
■ Adding weak or additional channels or erasing unwanted channels from TV memory
1
POWER
BRIGHT
SLEEP
2
Press a/b to move the cursor to
CH-SETTING, and press ENTER.
3
Press a/b to move the cursor to
CH MEMORY, and press ENTER.
4
Use a/b or Channel Select to
select each desired channel to add
or erase.
5
Press d to add the channel to the
TV memory or press c to erase
the channel from the TV memory.
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
CH
MENU
Channel
Select
Press MENU to display the MENU
screen, press a/b to move the
cursor to SET UP, and press
ENTER.
6
Press MENU to exit.
CH–SETT I NG
RETURN
EZ SETUP
A I R/ CABLE
CH SEARCH
CH MEMORY
CH MEMORY
AIR
TO ADD :
EX I T :
Press d
to add channel 2
to the TV memory
A
• If CH SEARCH is performed again,
the previously memorized channels
will be lost.
AIR
36
36
MENU
Press c
to erase channel 2
from the TV memory
CH MEMORY
TO ERASE :
LC-13/15/20S1U(Mex)(E)-c
2
03.12.15, 2:20 PM
2
EX I T :
MENU
ADJUSTMENTS (Continued)
Adjusting BLUE SCREEN Settings
■ BLUE SCREEN
Automatically turns the screen blue if no broadcast signal is received.
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
SET UP, and press ENTER.
POWER
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
SELECT :
MENU
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
3
CH
Press a/b to move the cursor
to BLUE SCREEN, and press
ENTER.
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
SET UP
RETURN
BLUE SCREEN [ OFF ]
LANGUAGE
CH–SETT I NG
CLOCK
MENU
SELECT :
4
Press c/d to select ON or OFF,
and press ENTER.
5
Press MENU to return to the main
screen.
ENTER : ENTER
SET UP
RETURN
BLUE SCREEN [ ON ]
LANGUAGE
CH–SETT I NG
CLOCK
ADJUST :
ENTER : ENTER
A
• When received signals are weak or interfered with by some other signals, the BLUE SCREEN function may be
activated. To watch the TV under such conditions, set BLUE SCREEN to OFF.
• The BLUE SCREEN function is activated when AV1, AV2 or COMPONENT input mode is selected with no signal
being input.
37
LC-13/15/20S1U(Mex)(E)-d
37
03.12.15, 2:21 PM
ADJUSTMENTS (Continued)
Adjusting CLOSED CAPTION Settings
■ SETTING CLOSED CAPTION
• This TV set is equipped with an internal Closed Caption decoder. “Closed Caption” is
a system which allows conversations, narration, and sound effects in TV programs
and home videos to be viewed as captions on the TV screen (see the illustration).
• Not all programs and videos will offer closed captioning. Please look for the “ ”
symbol to ensure that captions will be shown.
• The Closed Caption broadcasts can be viewed in two modes: CAPTION and TEXT.
For each mode, two channels are available: CH1 and CH2.
The CAPTION mode shows subscripts of dialogs and commentaries of TV dramas
and news programs while allowing a clear view of the picture.
The TEXT mode displays various information over the picture (such as TV program
schedules and weather forecasts, etc.) that is independent of the TV programs.
Directly setting the CLOSED CAPTION
POWER
BRIGHT
SLEEP
1
Press CC to display the CC/TEXT
screen.
2
Press CC to change the setting.
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
CC
OFF
CC 1
CC 2
T1
T2
FLASHBACK
VOL
CH
MUTE
A
• CC1: CAPTION mode for CH1 data
CC2: CAPTION mode for CH2 data
T1: TEXT mode for CH1 data
T2: TEXT mode for CH2 data
CC / TEXT [ CC 1 ]
A
• If a broadcast contains Closed Caption data and MUTE is pressed, the set enters CAPTION mode automatically.
Pressing MUTE again will return the set to its previous condition.
• Closed Caption may malfunction (white blocks, strange characters, etc.) if signal conditions are poor or if there are
problems at the broadcast source. This does not necessarily indicate a problem with your set.
• If any button is pressed to call up the On-Screen Display while viewing a Closed Caption broadcast, the closed
captions will disappear momentarily.
• If no TEXT broadcast is being received while viewing in the TEXT mode, the screen may become blank for some
programs. Should this occur, switch the Closed Caption mode to OFF.
38
LC-13/15/20S1U(Mex)(E)-d
38
03.12.15, 2:21 PM
ADJUSTMENTS (Continued)
Adjusting CLOSED CAPTION Settings (Continued)
■ SETTING CLOSED CAPTION
Setting the CLOSED CAPTION on the
MENU screen
POWER
1
Press MENU to display the MENU
screen.
2
Press a/b to move the cursor to
CLOSED CAPTION, and press
ENTER.
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b/c/d
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
FLASHBACK
VOL
CH
SELECT :
MENU
3
Press ENTER to change the
CLOSED CAPTION setting.
SELECT :
Press c/d to change the CLOSED
CAPTION setting, and press ENTER.
OFF
5
CC 1
CC 2
T1
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
CLOSED CAPT I ON
RETURN
CC / T EXT [ OFF ]
MUTE
4
ENTER : ENTER
ENTER : ENTER
CLOSED CAPT I ON
RETURN
CC / T EXT [ CC1 ]
T2
Press MENU to return to the main
screen.
ADJUST :
ENTER : ENTER
39
LC-13/15/20S1U(Mex)(E)-d
39
03.12.15, 2:21 PM
ADJUSTMENTS (Continued)
Adjusting V-CHIP Settings
■ V-CHIP
• This function allows TV programs to be restricted and TV usage to be controlled based on FCC data. It prevents
children from watching violent or sexual scenes that may be harmful.
• Restriction of TV programs includes two ratings that contain information about the program: the MPAA rating and
the TV Parental Guidelines. The MPAA rating is restricted by age. TV Parental Guidelines are restricted by age
and content.
• Since a TV program may use either the MPAA rating or the TV Guidelines, both should be adjusted for complete
control.
[1] MPAA RATING
RATING
age
based
G
GENERAL AUDIENCES. All ages admitted.
PG
PARENTAL GUIDANCE SUGGESTED. Some material may not be suitable for children.
PG-13
PARENTS STRONGLY CAUTIONED. Some material may be inappropriate for children under 13.
R
RESTRICTED. Under 17 requires accompanying parent or adult guardian.
NC-17
NO ONE 17 AND UNDER ADMITTED.
X
X is an older rating that is unified with NC-17 but may be encoded in the data of older movies.:
MPAA RATING
Example 1:
PG-13 in the age-based rating is
blocked, this will also automatically
block the higher ratings R, NC-17
and X.
Example 2:
R in the age-based rating is
blocked, this will also automatically
block the higher ratings NC-17 and
X.
ote:
A
• The MPAA rating is only age-based.
40
LC-13/15/20S1U(Mex)(E)-d
40
03.12.15, 2:21 PM
ADJUSTMENTS (Continued)
Adjusting V-CHIP Settings (Continued)
[2] TV PARENTAL GUIDELINES
⇐
FV
(Fantasy
Violence)
content based
⇒
V
(Violence)
S
(Sexual
Situation)
L
(Adult
Language)
D
(Sexually
Suggestive
Dialog)
xxx
✕
✕
✕
✕
TV-14 (Parents Strongly
Cautioned)
X
✕
✕
✕
✕
TV-MA (Mature Audience Only)
X
✕
✕
✕
RATING
TV-Y (All children)
⇑
TV-Y7 (Direct to Older Children)
TV-G (General Audience)
age
based TV-PG (Parental Guidance
Suggested)
⇓
✕
X
: The content rating can be set, but this rating is not normally broadcast by TV stations.
✕ : The content rating can be set.
TV PARENTAL GUIDELINES
Example 1:
When TV-Y7 in the age-based rating is set to BLOCK, this will automatically block the higher ratings: TV-G, TV-PG, TV-14
and TV-MA. In addition, D, L, S, V and FV in CONTENT are automatically blocked unless you manually set BLOCK
CONTENT.
Example 2:
When no item in the age-based rating is blocked, D in the content-based rating will be automatically blocked.
A
• Age-based ratings can be modified by the content-based ratings, but only in the combinations indicated by an X in
the table above.
• Choosing a lower age-based rating blocks the higher age-based ratings regardless of content rating settings.
• If you set TV-Y and TV-Y7 to BLOCK, CONTENT will display all items.
41
LC-13/15/20S1U(Mex)(E)-d
41
03.12.15, 2:21 PM
ADJUSTMENTS (Continued)
Adjusting V-CHIP Settings (Continued)
■ SETTING V-CHIP
[1] MPAA RATING
1
Press MENU to display the MENU
screen.
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
2
Press a/b to move the cursor
to V-CHIP BLOCK, and press
ENTER.
MENU
SLEEP T IMER
AV ADJUST
PRESET
CLOSED CAPT I ON
V–CH I P BLOCK
SET UP
3
INPUT SECRET NO. will be
displayed. Input the 4-digit
secret number by using
Channel Select, and press
ENTER.
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
CH
MENU
Channel
Select
I NPUT SECRET NO .
– – – –
A
• When you input the secret number for
the first time, press ENTER to register.
Otherwise, continue to step 4.
4
Press a/b to move the cursor to
MPAA, and press ENTER.
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
V–CH I P BLOCK
RETURN
MPAA
TV GU I DEL I NES
STATUS [ OFF ]
SELECT :
5
Press a/b to move the cursor
to PG, and press ENTER.
MPAA
RETURN
G
[ ––––– ]
PG
[ ––––– ]
PG–13 [ ––––– ]
R
[ ––––– ]
NC– 17 [ ––––– ]
X
[ ––––– ]
SELECT :
6
7
Press c/d to select BLOCK,
and press ENTER. If you set PG
to BLOCK, PG-13, R, NC-17 and
X are automatically blocked.
MPAA
RETURN
G
[ ––––– ]
PG
[ BLOCK]
PG–13 [ BLOCK]
R
[ BLOCK]
NC– 17 [ BLOCK]
X
[ BLOCK]
ADJUST :
42
42
ENTER : ENTER
Press MENU to return to the
main screen.
A
• If you set G to BLOCK, all ratings are automatically blocked.
• If you set X to BLOCK, G, PG, PG-13, R and NC-17 are not blocked.
LC-13/15/20S1U(Mex)(E)-d
ENTER : ENTER
03.12.15, 2:21 PM
ENTER : ENTER
ADJUSTMENTS (Continued)
Parent Control
Continued)
Adjusting
V-CHIP(V-CHIP
SettingsOperation
(Continued)
[2] TV GUIDELINES
● Setting TV GUIDELINES
1
Repeat steps 1 to 3 of [1] MPAA
RATING. (See page 42.)
2
Press a/b to move the cursor to
TV GUIDELINES, and press
ENTER.
POWER
BRIGHT
SLEEP
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
STATUS [ OFF ]
MENU
TV/VIDEO
ENTER/
a/b/c/d
FLASHBACK
VOL
V–CH I P BLOCK
RETURN
MPAA
TV GU I DEL I NES
SELECT :
CH
3
MENU
Press a/b to move the cursor to
TV-Y7, and press ENTER.
ENTER : ENTER
SELECT :
5
Press c/d to select BLOCK, and
press ENTER. If you set TV-Y7 to
BLOCK, TV-G, TV-PG, TV-14 and
TV-MA are automatically blocked.
In addition, D, L, S, V and FV in
CONTENT are automatically
blocked.
Press MENU to return to the main
screen.
MENU
EX I T :
MENU
EX I T :
MENU
TV GU I DEL I NES
RETURN
TV–Y [ ––––– ]
TV–Y7 [ ––––– ]
TV–G [ ––––– ]
TV–PG [ ––––– ]
TV– 14 [ ––––– ]
TV–MA [ ––––– ]
BLOCK CONTENT
[
4
EX I T :
]
ENTER : ENTER
TV GU I DEL I NES
RETURN
TV–Y [ ––––– ]
TV–Y7 [ BLOCK ]
TV–G [ BLOCK ]
TV–PG [ BLOCK ]
TV– 14 [ BLOCK ]
TV–MA [ BLOCK ]
BLOCK CONTENT
[ D L S V FV ]
ADJUST :
ENTER : ENTER
43
LC-13/15/20S1U(Mex)(E)-d
43
03.12.15, 2:21 PM
ADJUSTMENTS (Continued)
Adjusting V-CHIP Settings (Continued)
■ Setting BLOCK CONTENT
1
POWER
Repeat steps 1 to 3 of [1] MPAA
RATING. (See page 42.)
V–CH I P BLOCK
RETURN
MPAA
TV GU I DEL I NES
BRIGHT
SLEEP
STATUS [ OFF ]
PIC. FLIP
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
2
MENU
TV/VIDEO
ENTER/
a/b/c/d
Press a/b to move the cursor to
TV GUIDELINES, and press
ENTER.
FLASHBACK
VOL
SELECT :
ENTER : ENTER
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
EX I T :
MENU
CH
3
MENU
Press a/b to move the cursor to
BLOCK CONTENT, and press
ENTER.
TV GU I DEL I NES
RETURN
TV–Y [ ––––– ]
TV–Y7 [ ––––– ]
TV–G [ ––––– ]
TV–PG [ ––––– ]
TV– 14 [ ––––– ]
TV–MA [ ––––– ]
BLOCK CONTENT
[
SELECT :
4
Press a/b to move the cursor to
the desired item, and press
ENTER.
BLOCK CONTENT
RETURN
D [ ––––– ]
L [ ––––– ]
S [ ––––– ]
V [ ––––– ]
FV [ ––––– ]
SELECT :
5
Press c/d to select BLOCK or
----- (unblock), and press ENTER.
6
Press MENU to return to the
main screen.
]
ENTER : ENTER
ENTER : ENTER
BLOCK CONTENT
RETURN
D [ ––––– ]
L [ BLOCK ]
S [ ––––– ]
V [ ––––– ]
FV [ ––––– ]
ADJUST :
ENTER : ENTER
A
• If you set TV-14 to BLOCK, TV-MA is automatically blocked. Contents D, L, S and V are automatically blocked by
X in the table on page 41.
44
LC-13/15/20S1U(Mex)(E)-d
44
03.12.15, 2:21 PM
ADJUSTMENTS (Continued)
Adjusting V-CHIP Settings (Continued)
[3] ACTIVATING V-CHIP BLOCK
● Setting STATUS
You can activate V-CHIP BLOCK after setting [1] MPAA RATING and/
or [2] TV GUIDELINES.
1
Repeat steps 1 to 3 of [1] MPAA
RATING. (See page 42.)
2
Press a/b to move the cursor to
STATUS, and press ENTER.
POWER
BRIGHT
SLEEP
V–CH I P BLOCK
RETURN
MPAA
TV GU I DEL I NES
PIC. FLIP
ENTER
DISPLAY
MUTE
AUDIO
ONLY
MENU
CC
TV/VIDEO
ENTER/
a/b/c/d
STATUS [ OFF ]
FLASHBACK
VOL
SELECT :
CH
3
MENU
Press c/d to set STATUS to ON,
and press ENTER.
EX I T :
MENU
EX I T :
MENU
V–CH I P BLOCK
RETURN
MPAA
TV GU I DEL I NES
STATUS [ ON ]
A
• If STATUS is set to OFF, V-CHIP
BLOCK will not be activated.
4
ENTER : ENTER
Press MENU to return to the main
screen.
ENTER : ENTER
ADJUST :
[4] CANCELING THE V-CHIP BLOCK SCREEN WHILE V-CHIP BLOCK IS ACTIVATED
1
POWER
BRIGHT
SLEEP
PIC. FLIP
V-CHIP HAS BEEN ACTIVATED
appears if you watch a program
with the same Program Rating
data you configured.
V–CH I P HAS BEEN ACT I VATED
TV–Y
DISPLAY
ENTER
MENU
MENU
MUTE
AUDIO
ONLY
CC
TV/VIDEO
FLASHBACK
VOL
CH
A
• V-CHIP HAS BEEN ACTIVATED will
not be displayed if STATUS is not
configured to ON.
2
3
Channel
Select
Press MENU to display INPUT
SECRET NO.
I NPUT SECRET NO .
Input the 4-digit secret number by
using Channel Select; V-CHIP
BLOCK is temporarily canceled. If
you input an incorrect secret
number, SECRET NO. IS INCORRECT is displayed. In this case,
input the correct secret number.
– – – –
EX I T :
MENU
A
• If you turn the power on from off, V-CHIP BLOCK will be activated again.
• If you select V-CHIP BLOCK again by using MENU, V-CHIP BLOCK will be turned on again.
45
LC-13/15/20S1U(Mex)(E)-d
45
03.12.15, 2:21 PM
ADJUSTMENTS (Continued)
Adjusting V-CHIP Settings (Continued)
[5] CHANGING V-CHIP BLOCK SETTINGS
1
POWER
BRIGHT
SLEEP
Repeat steps 1 to 2 of [1] MPAA
RATING, then INPUT SECRET
NO. will be displayed.
I NPUT SECRET NO .
PIC. FLIP
– – – –
DISPLAY
MUTE
ENTER
AUDIO
ONLY
CC
MENU
TV/VIDEO
FLASHBACK
VOL
CH
2
Channel
Select
Input the 4-digit secret number by
using Channel Select; the VCHIP select mode will be displayed. Set V-CHIP BLOCK again.
EX I T :
MENU
EX I T :
MENU
I NPUT SECRET NO .
****
[6] CHANGING OR CLEARING THE SECRET NUMBER
If you forget the secret number, clear the secret number as follows.
Upper control panel
of the main unit
VOL (+)
CH (
1
Repeat steps 1 to 2 of [1] MPAA
RATING, or 1 to 2 of [4]
CANCELING THE V-CHIP
BLOCK SCREEN WHILE V-CHIP
BLOCK IS ACTIVATED, then
INPUT SECRET NO. will be
displayed.
2
Press and hold both CH ( ) and
VOL (+) on the TV set simultaneously until the message INPUT
SECRET NO. blinks.
3
Press MENU to exit.
) MENU
46
LC-13/15/20S1U(Mex)(E)-d
46
03.12.15, 2:21 PM
CONNECTING EXTERNAL DEVICES
You can enjoy picture and sound by connecting a VCR or a home video game system to the terminals
located on the rear of the TV set.
When connecting an external device, turn off the power of the main unit first to prevent any possible
damage.
Example of external devices that can be connected
To AV-IN1 terminal
To AV-IN2 terminal
<Example>
• Camcorder
• Home video game system
<Example>
• VCR
• Laser disc player
* If your external device has an S-video
terminal, S-VIDEO connection is recommended.
To COMPONENT terminal
<Example>
• DVD Player, etc.
Playback from 480 progressive output
for DVD and DTV is available.
* If your external device has a component
terminal, COMPONENT connection is recommended (you can view high-quality pictures).
A
• PC connection is not possible.
• For the cable, use a commercially available audio/video cable.
• Only connect audio/video signals to AV-IN1 and 2 terminals. Connecting other signals may result in a malfunction.
• AV-IN1 has 2 video input terminals: VIDEO and S-VIDEO. When you connect external devices to both terminals
(and if you select AV-IN1), you can only view pictures from the S-VIDEO terminal. To view the picture from the
VIDEO terminal, do not connect any external device to the S-VIDEO terminal.
• For more information about external device connections, see the manuals of your external devices.
• If HDTV (720P/1080I) signals are input to the COMPONENT terminals, “NOT COMPATIBLE WITH THIS SIGNAL”
will appear and playback cannot be viewed.
47
LC-13/15/20S1U(Mex)(E)-d
47
03.12.15, 2:21 PM
CONNECTING EXTERNAL DEVICES (Continued)
Connecting a VCR, DVD player or a video camera (AV-IN1/2/COMPONENT)
To AV-IN1 terminal
Video
Audio (L)
Audio (R)
To audio/video output
terminal
Camcorder
To S-VIDEO input
terminal
S-video
VCR
To S-video output
terminal
To COMPONENT input
(Video) terminal
To COMPONENT output
(Video) terminal
Y
PB
PR
To COMPONENT output
(Audio) terminal
Audio (L)
Audio (R)
To COMPONENT input
(Audio) terminal
DVD Player
To AV-IN2 terminal
Audio (R)
Audio (L)
Video
To audio/video output
terminal
To S-video input
terminal
To S-video output
terminal
VCR
S-video
A
• If your VCR (or other external devices) has an S-video terminal, S-VIDEO connection is recommended. (Use an
S-video cable.)
• When you connect external devices to both S-VIDEO and VIDEO terminals (and if you select AV-IN1), you can
only view pictures from the S-VIDEO terminal.
• You cannot view multiple or synthesized pictures by connecting two or more external devices. When connecting
an external device, use care to connect the video and audio cables to the corresponding terminals.
48
LC-13/15/20S1U(Mex)(E)-d
48
03.12.15, 2:21 PM
CONNECTING EXTERNAL DEVICES (Continued)
Outputting video and audio (video output)
You can output video and audio signals from the TV set through the AV output terminals (AV-OUT).
• When using AV2 as an output terminal, select PRESET in the MENU and set AV2 IN/OUT to OUT.
(See page 30.)
• The factory setting for AV2 IN/OUT is IN.
Connect to a VCR,
audio amplifier, etc.
A
• AV2 IN/OUT has 2 OUT modes (see page 30).
• When using the S-video input for AV-IN1, or Y, PB and PR input for COMPONENT, no video output will be made to
the AV output terminal, but audio output will be made for connection to external audio systems.
49
LC-13/15/20S1U(Mex)(E)-e
49
03.12.15, 2:22 PM
TROUBLESHOOTING
■ Before calling for repair services, make the following checks for possible remedies to
the encountered symptoms.
TV set
Problem
Sound
Picture
Picture
Check item
There is no
picture or
sound.
• Make sure the AC adapter is properly inserted in the
power outlet.
• Reception other than those of broadcasting stations
can be considered.
• Make sure the input mode is set to TV.
• Make sure the MAIN POWER switch of the main unit
is on.
There is no
picture.
There is no
picture from
AV-IN1/2.
• Make sure the BLACK LEVEL is properly adjusted.
• Fluorescent lamp may have reached the end of
service life.
• Make sure the S-VIDEO terminal has nothing connected.
• Make sure the AUDIO ONLY is not set to ON.
There is no
sound.
There is no
picture or
sound, just
noise.
Picture is not
clear.
Picture is light
or improperly
tinted.
The picture is
too dark.
Reference
Pages
11
–
22
21
32, 33
52
48
29
• Make sure the volume is not set to minimum.
• Make sure the sound is not set to mute.
• Make sure that headphones are not connected.
23
23
23
• Make sure the antenna cable is properly connected.
• Bad reception could be the problem.
10
–
• Make sure the antenna cable is properly connected.
• Bad reception could be the problem.
10
–
• Check color adjustment.
• Check COLOR SYSTEM setting.
• Press the BRIGHT button or set the BRIGHTNESS
settings.
• Check PICTURE and BLACK LEVEL adjustment.
• Fluorescent lamp may have reached the end of
service life.
32, 33
32, 33
27
32, 33
52
8
8
Remote control does not work.
• Check the batteries of the remote control.
• Make sure the remote sensor window is not under
strong lighting.
The clock (AUTO CLOCK)
cannot be set.
–
• The broadcasted EDS signal may be weak. Check the
antenna.
17–19, 35
• Carry out EZ SETUP, SETTING THE CLOCK again.
19
• If EDS signal is not sent, set the clock using MANUAL
CLOCK Setting.
50
LC-13/15/20S1U(Mex)(E)-e
50
03.12.15, 2:22 PM
TROUBLESHOOTING (Continued)
Antenna
Problem
Check item
The picture is
not sharp.
•
•
•
•
The reception may be weak.
The quality of the broadcast may also be bad.
Make sure the antenna is facing the right direction.
Make sure the outside antenna is connected.
The picture
moves.
The picture is
doubled or
tripled.
The picture is
spotted.
There are
stripes on the
screen or
colors fade.
• Make sure the antenna is facing the right direction.
• There may be reflected electric waves from mountains or
buildings.
• There may be interference from automobiles, trains, high
voltage lines, neon lights, etc.
• There may be interference between the antenna cable and AC
cord. Try positioning them further apart.
• Is the unit receiving interference from other devices?
Transmission antennas of radio broadcasting stations, transmission antennas of amateur radios and cellular phones may also
cause interference.
• Use the unit as far apart as possible from devices that may
cause possible interference.
■ Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear
slightly delayed. This is not a malfunction, and the unit will recover when the temperature returns normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight
or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: –4°F to +140°F (–20°C to +60°C)
51
LC-13/15/20S1U(Mex)(E)-e
51
03.12.15, 2:22 PM
SPECIFICATIONS
Items
Model
LCD panel
Number of dots
Video color systems
TV Standard (CCIR)
TV Tuning System
TV function
STEREO
CATV
Y/C FILTER
Brightness
Lamp life (Fluorescent lamp)
Viewing angles
Audio amplifier
Speakers
AV-IN1
AV-IN2
Terminals
COMPONENT
Antenna
Headphone
OSD language
Power supply
Power consumption
Weight
Accessories
LC-13S1U
LC-15S1U
LC-20S1U
13” Advanced Super View 15” Advanced Super View 19.7” Advanced Super
& BLACK TFT LCD
& BLACK TFT LCD
View & BLACK TFT LCD
921,600 dots VGA
N358, N443, PAL, PAL-M, PAL-N, SECAM, PAL-60
NTSC/PAL-M/PAL-N
PLL 181 ch.
MTS+SAP
125 ch.
3-LINE COMB FILTER
3D Y/C FILTER
430 cd/m2
60,000 hours
H: 170° V: 170°
2.1 W ⳯ 2
3 ⳯ 7.5 cm, 2 pcs.
4 ⳯ 7 cm, 2 pcs.
AV-IN1, S-VIDEO-IN
AV-IN2, S-VIDEO-IN/AV-OUT
COMPONENT-IN, AUDIO-IN
F-Type
Mini-jack for stereo (ø3.5 mm)
English/French/Spanish
DC 12 V, AC 110–240 V, 50/60 Hz (AC Adapter), AC 125V MAX (AC Cord)
41 W (0.5 W Standby)
64 W (0.5 W Standby)
39 W (0.5 W Standby)
AC 120 V
AC 120 V
AC 120 V
(with AC adapter)
(with AC adapter)
(with AC adapter)
34 W: DC 12 V
37 W: DC 12 V
55 W: DC 12 V
7.9 lbs. (3.6 kg),
9.3 lbs. (4.2 kg),
14.1 lbs. (6.4 kg),
w/o accessories
w/o accessories
w/o accessories
Remote control, Battery (x2), Antenna cable, AC adapter,
AC cord, Cable clamp, Operation manual
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of
production units. There may be some deviations from these values in individual units.
52
LC-13/15/20S1U(Mex)(E)-e
52
03.12.19, 0:12 PM
DIMENSIONAL DRAWINGS
■ LC-13S1U
Unit: inch (mm)
553/64 (148)
1037/64 (269)
1121/64 (288)
12°
4 7/8 (124)
12 23/32 (323)
919/64 (236)
35°
1117/32 (293)
17
/64 (7)
6 23/64 (161.7)
7 29/32 (200.8)
817/64 (210)
103/16 (259)
1033/64 (267)
6 3/16 (157)
3 55/64 (98)
47/8 (124)
2 21/64 (59)
11/2 (38)
5 45/64 (145)
315/16 (100)
315/16 (100)
51/32(128)
53
LC-13/15/20S1U(Mex)(E)-e
53
03.12.15, 2:22 PM
DIMENSIONAL DRAWINGS (Continued)
■ LC-15S1U
Unit: inch (mm)
61/64 (153)
111/2 (292)
12 35/64 (319)
12°
5 5/64 (129)
1419/64 (363)
9 51/64 (249)
35°
123/4 (324)
9 3/32 (231)
17
/64 (7)
615/16 (176.2)
91/64 (229)
117/32 (285)
12 5/64 (307)
7 1/8 (181)
3 55/64 (98)
21
5 3/16 (132)
2 /64 (59)
113/16 (46)
61/4 (159)
315/16 (100)
315/16 (100)
515/64 (133)
54
LC-13/15/20S1U(Mex)(E)-e
54
03.12.15, 2:22 PM
DIMENSIONAL DRAWINGS (Continued)
■ LC-20S1U
Unit: inch (mm)
649/64 (172)
137/32 (336)
1529/32 (404)
12°
69/64 (156)
1821/32 (474)
119/64 (283)
35°
163/16 (411)
/ (5)
9 (228.5)
1023/64 (263)
141/64 (356)
1127/32 (300.8)
15 7/8 (403.3)
3 16
939/64 (244)
47/32 (107)
517/64 (134)
243/64 (68)
127/32 (47)
751/64 (198)
315/16 (100)
315/16 (100)
619/64 (160)
55
LC-13/15/20S1U(Mex)(E)-e
55
03.12.15, 2:22 PM
CALLING FOR SERVICE
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or customer
assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”),
when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its
option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no
charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor
to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other
misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED
TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described
herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein,
shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product,
and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or
attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible
for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or
consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
LC-13S1U LCD Color Television
LC-15S1U LCD Color Television
LC-20S1U LCD Color Television
(Be sure to have this information available when you need service for
your Product.)
Warranty Period for this Product:
One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from
Warranty Coverage (if any):
Non-rechargeable batteries.
From a Sharp Authorized Servicer located in the United States.
To find the location of the nearest Sharp Authorized Servicer, call Sharp
toll free at 1-800-BE-SHARP.
Where to Obtain Service:
What to do to Obtain Service:
Ship prepaid or carry in your Product to a Sharp Authorized
Servicer. Be sure to have Proof of Purchase available. If you ship
the Product, be sure it is insured and packaged securely.
TO OBTAIN PRODUCT INFORMATION, CALL 1-888-LCD-SHARP OR VISIT www.sharpusa.com
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
56
LC-13/15/20S1U(Mex)(E)-e
56
03.12.15, 2:22 PM
VALID IN CANADA ONLY
LIMITED WARRANTY
Consumer Electronics Products
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for this
Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer:
Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any such
defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the product as
specified herein.
This warranty shall not apply to:
(a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate
use as outlined in the owner’s manual.
(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp’s Authorized Service Centres
or Sharp’s Authorized Servicing Dealers.
(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited to
head cleaning tapes and chemical cleaning agents.
(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including but
not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons, cables and
paper.
(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.
(f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or liquid
spillage.
(g) Any product received without appropriate model, serial number and CSA/cUL markings.
(h) Any products used for rental or commercial purposes.
(i) Any installation, setup and/or programming charges.
Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product
together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an
Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp’s discretion on any Sharp television with the
screen size of 27” or larger and on any Sharp Over-the-Range Microwave Oven.
This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is
authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all
liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a
defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss
of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of
defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp
to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict
liability or otherwise.
WARRANTY PERIODS:
Audio Products
Camcorder
DVD Products
Projector
LCD & Plasma Display TV
Microwave Oven
Television Products
VCR Products
Vacuum Cleaner
Parts &
1 year
1 year
1 year
1 year
1 year
1 year
1 year
1 year
1 year
Labour (exceptions noted)
(lamp 90 days)
(magnetron component-4 additional years)
(picture tube component-1 additional year)
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario L4Z 1W9
For more information on this Warranty, Sharp Extended Warranty
Offers, Sharp Canada Products, Accessory Sales, Dealer or Service
Locations, please call (905) 568-7140
Visit our Web site: www.sharp.ca
57
LC-13/15/20S1U(Mex)(E)-e
57
03.12.15, 2:22 PM
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
TELEVISOR DE CRISTAL
LÍQUIDO
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACIÓN
MANUAL DE OPERAÇÃO
Printed in Mexico
Imprimé au Mexique
Impreso en México
Impresso no México
TINS-A857WJZZ
04P03-MMG(J)
Products that have earned the ENERGY STARb are designed to protect the
environment through superior energy efficiency.
FRANÇAIS
ESPAÑOL
LC-13S1U
LC-15S1U
LC-20S1U
PORTUGUÊS
LC-13S1U/LC-15S1U/LC-20S1U
ENGLISH
03. 12. 11
LC-13/15/20S1U(Mex)Cover