Sharp LC-42D64U Operating instructions

SHARR
LC-42D64U
LC-46D64U
LC-52D64U
LIQUID CRYSTAL
TELI_VISEUR
TELEVISION
ACL
TELEVISOR
CON PANTALLA
DE CRISTAL LiQUIDO
OPERATION
MANUAL
MODE D'EMPLOI
MANUAL
DE OPERACION
AQUOS
HBGH._FINI
IO
T_L_VISION
DB[DOLBYI
Hii:3rlrllll
DIGITAL
HIGH DEfINItION MULTIMEDIA I_TER_ACE
IMPORTANT
: Please read this operation manual before starting operating
IMPORTANTE
: Lea este manual de operaci6n
antes de comenzar
TM
the equipment.
a operar el equipo.
LC-42D64U
LC-46D64U
LC-52D64U
LiQUiD CRYSTAL
TELEViSiON
ENGLISH
OPERATION
MANUAL
- The ilkJstrationsand on screen displays in this operation
manual are for explanation purposes and may vary slightly from
the actual operations.
- Menu items that are not selectable are grayed out.
- The examples used throughout this manual are based on the
LC 42D64U model.
i
iMPORTANT:
To aid reporting in case of loss or theft, please record the
TV's model and serial numbers in the space provided. The
numbers are located at the rear of the TV.
iMPORTANT
[ WARNING:
Serial No.:
Model No.:
iNFORMATiON
TO
OF FIRETO
ORRAIN
ELECTRIC
SHOCK,
NOTREDUCE
EXPOSE THE
THISRISK
PRODUCT
OR MOISTURE,
DO
i
The lightning flash with arrow-head
symbol, within an equilateral triangle,
is intended to alert the user to the
RISK OF ELECTRICSHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION:
presence of uninsulated "dangerous
voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a
triangle is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the product.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
(D-I
iMPORTANT
iNFORMATiON
CAUTION:
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRADKET, OR TABLE.
THE PRODUCT MAY FALL CAUSING SERIOUS PERSONAL INJURY AND SERIOUS DAMAGE TO
THE PRODUD]_ USE ONLY WITH A DART, STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED
BY THE MANUFACTURER OR SOLD WITH THE PRODUD]_ FOLLOW THE MANUFACTURER'S
INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND USE MOUNTING ACCESSORIES
RECOMMENDED BY THE MANUFACTURER, A PRODUCT AND DART COMBINATION SHOULD BE
MOVED WITH CARE. QUICK STOPS, EXCESSIVE FORCE, AND UNEVEN SURFACES MAY CAUSE
THE PRODUCT AND CART COMBINATION TO OVERTURN.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment
approved by the manufacturer could void the user's authority to operate this equipment.
not expressly
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic
interference with electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-42D64U/LC-46D64U/LC-52D64U
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLEPARTY:
SHARP ELECTRONICSCORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National
Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical."
This product utilizes tin-lead solder, and fluorescent
lamp containing a small amount
mercury. Disposal of these materials may be regulated due to environmental
considerations.
For disposal or recycling information,
please contact your local
authorities, the Electronic Industries Alliance: www.eiae.org,
the lamp recycling
organization: www.lamprecycle.org
or Sharp at 1-800-BE-SHARP
(For U.S.A. only)
of
Trademarks
, Laboratories.
anufactured
under license from Dolby Laboratories.
" Licensing
"HDMI, theLLC."
HDMI logo and High-Definition
"Dolby"
and the double-D
Multirnedia Interface are trademarks
symbol are trademarks
or registered tradernarks
_ efficiency.
roducts that have earned the ENERGY STAR ® are designed to protect the environment
(D-2
through
of Dolby
of HDMI
superior energy
i
J
1
1
J
i
DEAR SHARP CUSTOMER
Thank you for your purchase
of the Sharp Liquid
of troubme=free
operation
of your product,
please
using this product.
iMPORTANT
Crystal
Television.
read the important
To ensure
safety and many years
Safety instructions
carefully
before
SAFETY iNSTRUCTiONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled, This product has been engineered and manufactured with the highest priority on safety,
However, improper use can result in electric shock and/or fire, In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product, To ensure your safety
and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully
before using the product,
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
Read these instructions,
Keep these instructions,
Heed all warnings,
Follow all instructions,
Do not use this apparatus near water,
Clean only with dry cloth,
Do not block any ventilation openings, Install in accordance with the manufacturer's
instructions,
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat,
Do not defeat the safety purpose of the polarized or grounding-type
plug, A polarized plug has two blades
with one wider than the other, A grounding type plug has two blades and a third grounding prong, The
wide blade or the third prong are provided for your safety, If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet,
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus,
Only use attachments/accessories
specified by the manufacturer,
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus, When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over,
Unplug this apparatus during lightning storms or when unused for long periods of time,
Refer all servicing to qualified service personnel, Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped,
Additional
Safety
information
15) Power Sources--This
product should be operated only from
marking label. If you are not sure of the type of power supply
local power company. For products intended to operate from
operating instructions.
16) Overloading-Do
not overload wall outlets, extension cords,
can result in a risk of fire or electric shock.
the type of power source indicated on the
to your home, consult your product dealer or
battery power, or other sources, refer to the
or integral convenience
receptacles
as this
17) Object and Liquid Entry--Never
push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
18) Damage Requiring Service--Unplug
this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by a qualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for service.
19) Replacement Parts-When
replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions
may result in fire, electric shock, or other hazards.
20) Safety Check-Upon
completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
21) Wall or ceiling mounting-When
mounting the product on a wall or ceiling, be sure to install the product
according to the method recommended by the manufacturer.
(D-3
iMPORTANT
!
SAFETY iNSTRUCTiONS
kitchWater
bowl, and en
Moisture
Do not tub;
use in
this
product
near water
bath tile
tub,like.
wash
sink, or-- laundry
a wet
basement;
or ,learfor
a example,
swimming near
pool;a and
_
___
_
product on an unstable base can cause ttle product to fall, resulting in serious personal injuries
as well as damage to tile product. Use only a cart, stand, tripod, bracket or table recommended
by tile manufacturer or sold wittl tile product. When mounting tile product on a wall, be sure to
, follow
Starld the
-- Do
not place tile instructions.
product oil an
stand, tlardware
tripod or table.
Placing the
manufacturer's
Useunstable
only tile cart,
mounting
recommended
by the
|
|
|
"_
|
manufacturer.
Selecthlg ttle ,ocation -
)
Se,ect a place wittl no direct sun,ight and good ventilation.
V_
"/
cover or block these vents and openings since insufficient ventilation can cause overheating
and/or shorten the life of tile product. Do not place tile product on a bed, sofa, rug or ottler
similar surface, since ttley carl block ventilation openings. This product is not designed for built
in installation; do not place tile product in an enclosed place such as a bookcase or rack, unless
, proper
eiltilation
-- Tile is
vents
and other
in tile cabinet
are designed
for ventilation. Do not
ventilation
provided
or theopenings
manufacturer's
instructions
are followed.
product is dropped or applied wittl impact. Be careful not to be injured by broken glass pieces
in case tile panel breaks.
registers, stoves, or ottler products (including amp#Jets) that produce heat.
,
eat -- Tile product should be situated away from heat sources such as radiators, heat
__}
details.
|
Occasionally,
a fewpanel
non active
pixels
appear on
the screen
as a fixed ttlin
pointfilm
of blue,
green or
red.you
Please
that this I
, The
Liquid Crystal
is a very
highmay
tectlnology
product
wittl 6,220,800
transistors,
giving
fine note
picture
does not affect the performance of your product.
)
Be sure to always carry the TV by two people holding it with two hands - one hand on
Preeautions
when transporting
each side of the TV.
the TV
, Lightlling - For added protection for this television equipment during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from ttle wall outlet
and disconnect the antenna This will prevent damage to the equipment due to lightning and
power line
surges.
'
_ _
,-s
_
1177--_
lY
_l
r"
_|
:#" !
19m_ _J
_J
power lines or other electric light or power circuits, or wtlere it can fall into suctl power lines
or circuits. When installing an outside antenna system, extreme care should be taken to keep
power lines
or circuits
contactnotwith
tilem might
fatal. of overhead
, from
Powertouching
Lines --such
An outside
antenna
systemasshould
be located
in thebevicinity
189-4
__
iMPORTANT
SAFETY iNSTRUCTiONS
Outdoor Antenna Grounding -- If an outside antenna is connected to the televbion equipment, be sure the antenna
system is grounded so as to provide some protection agaklst voltage surges and buibup static charges.
Article 810 of tile National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of tile
mast and supporting structure, grounding of tile lead in wire to an antenna discharge unit, size of grounding conductors,
|
|
|
location of antenna disctlarge
/
unit, connection
to grounding electrodes, and requirements
for tile grounding electrode.
/
EXAMPLE OF ANTENNA GROUNDING AS PER
|
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
/
/
--___
ANTENNA
//_:_.._D
J
Z/
GROUND ,,,_/_
CLAMP
_____
]'N_
/,/_.
|
IN WIR E
/
ANTENNA
|
_ I "x_N DISCHARGE UNIT
_£
|
/
(NEC SECTION 810 20)
LEQUIPMENT--__._.J_
_
GROUNDING CONDUCTORS
--------_..._
lL_f____________...,.--"_
(NEC SECTION 810 21)
--_
--'_
NEC -- NATIONAL ELECTRICAL CODE
|
|
_/UEF_DsCRLOM_SGRoU NDING ELECTRODE
/
SYSTEM
|
(NEC ART 250, PART H)
/
J
A
any
-To
prevent fire, never place
type of candle or flames on the top or near the TV set.
No objects filled with liquids, such as vases, should be placed on the product.
. To prevent fire or shock hazard, do not expose this product to dripping or splashing.
|
J
"_
items.
.
o prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy
f
* Turn off the main power and unplug the AC cord from the wall outlet before handling.
* Use a soft cloth and gently wipe tile surface of tile display panel. Using a tlard cloth may
scratch the panel surface.
* Use a soft damp dottl to gently wipe tile panel wtlen it is really dirty.
(It may scratch the panel surface when wiped strongly.)
* If the panel is dusty, use an anti static brust% which is commercially available, to clean it.
* To protect the panel, do not use a dirt)/cloth, liquid cbaners or chemical clottl to clean it,
such materials may damage the panel surface.
* To clean tile outer cabinet, use tile same method. Do not use liquid or aerosol cleaners.
__
"Do
not display a still picture for a long time, as this could cause an afterimage to remain.
J
}
@-5
Supplied accessories
Make sure the following
accessories
are provided
with the product.
f
Remote control unit
(xl)
Page 8
"AAA" size battery
(x2)
Page 8
AC cord
(xl)
Page 7
Cable clamp (x 1)
Cable tie (x 1)
Page 7
Stand unit
(x 1)
Page 6
Operatbn manual
(x 1)
,J
,, Always use the AC cord supp[bd with the TV.
,, AC cord enclosed in this product is for 110-125V. In using it on the 125 240V AC, phase consult to the following.
SHARP ELECTRONICS CORPORATION,
LATIN AMERICA GROUP
6100 Blue Lagoon Drive, Suite 150, Miami, Florida 33126, U.S.A.
QUICK REFERENCE
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it
from being damaged.
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect
installation
Confirm that there are 8 screws (4 short
screws and 4 long screws) supplied with the
stand unit.
of the stand may result in the TV falling
over.
(_ Insert the stand into the openings on the
bottom of the TV.
(_) Insert and tighten the 4 short screws into
the 4 holes on the rear of the TV.
Attach the supporting
post for the stand unit
onto the base using the box for the stand unit
as shown below.
,, The supporting post attaches to the base at
an off centered location on the base. Be sure
to attach the supporting post in the direction
indicated bebw and attach the stand to the TV
with the wider side of the base facing forward.
Hex key
screws _
,, To detach tile stand, perform the steps in reverse order.
(@)-6
QUICK
REFERENCE
STOP! To safely remove
the AQUOS television
from the box
* It's best to use 2 people to remove the AQUOS television for stability.
e Lift onto installation location as the diagram illustrates.
Ventilation
& Cleaning
Tips
Keep your AQUOS television in a well ventilated area and make sure not to place it by a heat source or use near
water. The AQUOS television is designed for AC use only and should be used with supplied AC cord.
Clean the screen by spraying a soft lint free cloth with water to lightly moisten. Gently wipe and
avoid pressing on the screen. To clean the outer cabinet, use the same method. Do not use
liquid or aerosol cleaners.
IX_
_
_-_' [_--_-__
The screen is glass and can be scratched or broken when dropped or impacted.
QUICK iNSTALLATiON
_ _ J/ /
TiPS
Attach your antenna to the back of the AQUOS
television. (See page 12.)
How to turn on the AQUOS television for the
first time.
A) Press POWER on the AQUOS television.
Connect the AC plug for the AQUOS television
into the AC outlet.
_ower
MENU
O
INPUT
B) The POWER indicator on the front of the
AQUOS television lights GREEN,
,, Place ttqeTV close to tile AC outlet, and keep tile power
plug within reactq.
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED
PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
Place the Ferrite core in the space indicated in
the below figure and bundle the cords properly
with the cable clamp and the cable tie.
Ij
0
0
o
o
POWER indicator
,, Speakers cannot be detached from ttqe TV.
• TV angb cannot be adjusted.
Ferrite core
(D-7
QUICK REFERENCE
If the remote control fails to operate TV functions, replace the batteries in the remote control unit,
1 Open the battery
2 hTserttwo "AAA" size batteries
(supplied with the product),
cover.
3 Close the battery
cover.
• Place the batteries with their terminals
corresponding to the (+) and ( )
indications in the battery compartment.
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical
leakage in old batteries.
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause
a rash. If you find any chemical leakage, wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove batteries from it.
Remote control sensor
POWER
)
/
E
O
o
SLEEP
o
()PC
o
m
J
30 °`
1T(5 m)
i
30°
30 °
30°
IMPORTANT:
The POWER indicator on the AQUOS television should light GREEN indicating you have
power to the AQUOS television.
If the POWER indicator on the AQUOS television still does not light up, press TV POWER
on the remote control to turn the power on.
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE AQUOS TELEVISION FROM THE OUTLET AND REPEAT
THE INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT US AT 1-800-BE-SHARP.
Please refer to the BASIC ADJUSTMENT SETi-INGS SECTION for EZ Setup and basic channel setup functions
and USING EXTERNAL EQUIPMENT SECTION for other device connections (DVD, VCR, AUDIO, etc.) in your
AQUOS operation manual.
(D-8
Contents
IMPORTANT INFORMATION ................................. 1
Trademarks .............................................................
2
DEAR SHARP CUSTOMER .................................... 3
IMPORTANT SAFETY INSTRUCTIONS ................. 3
Supplied accessories .............................................
6
QUICK REFERENCE ...............................................
6
Attaching the stand .............................................
6
Contents ..................................................................
9
Part names .............................................................
10
TV (Front) ...........................................................
10
TV (Rear/Side) ....................................................
10
Remote control unit ........................................... 11
Preparation ............................................................
12
Using the remote control unit ............................. 12
Cautions regarding the remote control unit_..12
Antennas ...........................................................
12
Connecting a Blu-ray disc player, HD-DVD player,
DVD player or a Digital TV STB (Air or Cable)...13
Connecting a VCR, game console
or camcorder ...................................................
14
Using Digital Audio Output ................................. 14
Connecting HDMI equipment ............................. 15
Connecting a PC ...............................................
15
PC compatibility chart ........................................ 15
Watching _ ...........................................................
16
Turning on the power ......................................... 16
Turning off the power ......................................... 16
Initial setup ........................................................
17
Simple button operations for
changing channels .......................................... 18
Simple button operations for
changing volume/sound .................................. 19
Setting MTS/SAP stereo mode .......................... 20
Setting Digital broadcasting audio mode ............ 20
Basic adjustment settings ................................... 21
Menu operation buttons .................................... 21
On-Screen Display ............................................
21
Menu items for TV/INPUT 1/2/3 ........................ 22
Menu items for HDMI/PC-IN ............................. 22
EZ Setup ..........................................................
23
Channel Setup ..................................................
23
Antenna Setup - DIGITAL ................................. 24
Favorite channel setting .................................... 25
Picture adjustments ..........................................
26
OPC setting .................................................
26
Advanced picture adjustments ..................... 27
C.MS (Color Management System) ............ 27
Color Temperature .......................................
27
Active Contrast ............................................
27
Fine Motion ..................................................
27
I/P Setting .....................................................
27
Film Mode (3:2 pull-down) ............................ 28
3D-Y/C ........................................................
28
Monochrome ...............................................
28
Range of OPC ..............................................
28
Sound adjustment ............................................
28
Surround ..........................................................
29
Bass Enhancer .................................................
29
Power Control ..................................................
29
Using external equipment ....................................
Displaying an external equipment image ...........
Input Select ......................................................
Displaying an image from HDMI equipment .......
Input Skip .........................................................
Useful adjustment settings ..................................
Auto Sync. adjustment
(for Analog PC input mode only) .....................
Fine Sync. adjustment ......................................
Image position ..................................................
Language setting ..............................................
Reset ................................................................
Input Label ........................................................
Sleep Timer ......................................................
View Mode for 4:3 Programs ............................
View Mode for HD Programs ............................
View Mode for PC input mode ..........................
Advanced Option settings .................................
Audio Only ...................................................
Digital Noise Reduction ................................
Program Title Display ...................................
Output Select ...............................................
Color System ...............................................
Game Play Time ...........................................
Operation Lock Out ......................................
AV MODE .........................................................
Input Signal (for Analog PC input mode only) ....
Closed Captions and Digital Closed Captions.
Caption Setup ..................................................
Digital Caption Information ................................
Secret number setting for parental control ........
Parental control (setting V-CHIP level) ...............
How to temporarily release
the V-CHIP BLOCK ........................................
Reactivating the temporarily released
V-CHIP BLOCK ..............................................
Digital Setup .....................................................
Audio Setup .................................................
Identification .................................................
Software Update ..........................................
Other viewing options ..........................................
Freezing images ................................................
Presetting remote control function ....................
Controlling HDMI Equipment Using AQUOS LINK.
Appendix ...............................................................
Removing the stand ..........................................
Setting the TV on the wall .................................
Troubleshooting ................................................
Troubleshooting-Digital broadcasting ................
RS-2320 port specifications .............................
Specifications ..................................................
Optional accessory ............................................
Information on the software license for this
product ...........................................................
Calling for Service ................................................
LIMITED WARRANTY ...........................................
30
30
30
31
31
32
32
32
33
33
33
34
34
35
35
36
37
37
37
37
37
37
37
37
38
38
39
40
40
41
43
47
47
47
47
47
48
50
50
50
54
58
58
58
59
59
60
62
62
64
65
65
Dimensional
drawings
• The dimensional drawings for tile LCD TV set are shown
on the inside back cover
(D-9
PaPt
names
OPC sensor*
i
_
f_OWER
SLEEP
OPC
t
_
I
*OPC: Optical Picture Control (See page 26.)
**See page 16 for TV status indicator.
Remote control sensor
SLEEP indicator**
OPC indicator**
POWER indksator**
button
RS-232C
terminal
__
INPUT 3
terminals
Channel buttons
(CHA/V)
DIGITAL AUDIO
OUTPUT terminal
volume buttons
HDMI terminal
(INPUT 5)
(VOL+/-)
--
HDMI terminal
(INPUT 4)
--
USB terminal
HDMI terminals
(INPUT 6)
INPUT 7 terminals
(PC-IN)
Antenna/Cable
in
INPUT 1 terminals
INPUT 2 terminals
©®®®®@®@@®
i
(D-
10
terminals
AUDIO OUTPUT
AC INPUT terminal
PaN
names
1
rv
POWER: Switch the TV power on or enters standby.
(See
page 16.)
16
2
DISPLAY: Display the channel information.
3
SOURCE POWER: Turns the power of the external equipment
on and eft.
4
External
equipment
operational
buttons:
Operate the external
equipment.
2
/
3
°;
souooE
5
0 - 9: Set the channel. (See page 18.)
6
* (DOT): (See pages 18 and 52.)
7
INPUT: Select a-IV input source. (TV, INPUT 1, INPUT 2, INPUT 3,
INPUT 4, INPUT 5, INPUT 6, INPUT 7) (See pages 30 and 31 .)
8
VOL +/-
9
SURROUND:
10
FREEZE: Set the still image. Press again to return to normal
: Set the vokJme. (See page 19.)
Select Surround settings. (See page 19.)
screen. (See page 50.)
11
12
5
6
IN_T
VOL
FREEZE
10 _8
FL_ACK
20
CH
13
12
SLEEP: Set the sleep timer. (See page 34.)
AUDIO: Selects the MTS/SAP or the audio mode during multi
channel audio broadcasts. (See page 20.)
16
FUNCTION:
MENU
Switches the remote control for TV, CBL/SAT, VCR,
DVD and AUDIO operation.
25
ii_
REC STOP: Stops one touch recording. This button will function
only when AQUOS LINK is used. (See pages 54 to 57 for details.)
15
• To enter the code registration mode, you need to press
FUNCTION and DISPLAY at the same time.
17
LIGHT _: When pressed all buttons en the remote control unit
will light. The lighting will turn off if no eperations are performed
within about 5 seconds. This button is used for performing
operations in lew light situations.
26
13--
Indicator lights up for the current
mode. (See pages 50 to 53 for details.)
24
_T
Display the AQUOS LiNK MENU screen. This button
14
23
11
OPTION:
will function only when AQUOS LINK is used. (See pages 54 to 57
for details.)
19
7
EXIT: Turn off the menu screen.
18
VIEW MODE:
19
ENT: Jumps to a channel after selecting with the 0 9 buttons.
20
FLASHBACK:
14
Select the screen size. (See pages 35 and 36.)
Return to the previous channel or external input
mode. (See page 18.)
15
29
21
CH/X/V:
22
MUTE: Mute the sound. (See page 19.)
23
MENU: Display the menu screen.
24
A/_'/_/I_/ENTER:
25
RETURN:
26
Select the channel. (See page 18.)
Select a desired item on the screen.
Return to the previous menu screen.
FAVORITE CH
A, B, C, D: Select 4 preset favorite channels in 4 different
categories. (See page 25 for details.)
While watching, you can toggle the selected channels by pressing
A, B, Cand D.
e _"
o
27
FAVORITE:
28
CC: Display captions from a closed caption source. (See page
Set the favorite channels. (See page 25.)
29
AV MODE: Select an audio or video setting.
39.)
(When the input source is -IV, INPUT 1,2 or 3: STANDARD,
MOVIE, GAME, USER, DYNAMIC (Fixed), DYNAMIC. When the
input source is INPUT 4, 5, 6 or 7: STANDARD, MOVIE, GAME,
PC, USER, DYNAMIC (Fixed), DYNAMIC) (See page 38.)
,, When using the remote control unit, point it at the TV.
(D-11
Preparation
Use the remote control unit by pointing it towards the remote control sensor on the
TV. Objects between the remote control unit and the remote control sensor may
prevent proper operation.
Do not expose the remote
control unit to liquids, and
,, Do not install or place ttqe
deformation of the remote
control
do not
remote
control
,,I/
unit to shock. In addition, do not expose tile remote
pBce hi an area wittl high humidity.
control unit under direct sunlight. The heat may cause
unit.
2
.,
,, The remote control unit may not work properly if ttqe remote control sensor on ttqe TV is
under direct sunlight or strong lighting. In suctq cases, ctlange the angle of the lighting or
the TV, or operate the remote control unk closer to the remote control sensor.
-,.-
J
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the TV set.
"I.A 75 ohm system is generallya round cable with F type _
connector that can easilybe attached to a terminal
without tools (Commerciallyavailable).
F-type connector
75-ohm coaxial cable (round)
f
_
F-type connector
tightened
only.
be finger=
When connecting the RF cable to the TV set, do not
tighten F-type connector with tools.
If tools are used, it may cause damage to your TV
set. (The breaking of internal circuit, etc.)
2.A 300 ohm system is a flat "twin lead" cable that can be
attactqed to a 75 ohm terminal ttqrough a 300/75 ohm
adapter (Commercially available).
F-type connector
75-ohm coaxial cable
300-ohm twinqead cable (flat)
,._
should
J
k_
_,
r
Connecting
Antenna
Cable
Home
terminal
@ Cable without a CATV
converter
Antenna
(75
ohm}
Cob_eWiead_n
Coaxisl
cable
(oommemial_y
VHF/UHF
available}
antenna
• Connect
_4J_75
Home
ohm
coaxJaJ cable
(round)
terminal
Antenna
(75
ohm)
Co_ial
cable
(commercially
Combination VHF/
UHF antenna
available}
300/75-ohm adapt_
VHF
ANTENNA
Separate
UHE
ANTENNA
the antenna
cable
to the TV using one of the
methods in the illustration
as shown (_}, (2}, _3) or (4}}.
(commemially
available)
VHF/UHF
antenna
To TV antenna
terminal
Preparation
You can connect many types of external equipment to your TV like a Blu-ray disc player, HD-DVD player, DVD
player, VCR, Digital TV tuner, HDMI equipment, game console or camcorder. To view external source images,
select the input source from INPUT on the remote control unit or on the TV. (See pages 30 and 31 .)
,, To protect equipment, always turn off the TV before connecting any external equipment.
,, Please read the relevant operation manual (Blu ray disc player, etc.) carefully before making connections.
You can use the INPUT 1, INPUT 2 or INPUT 3 terminals when connecting to a Blu-ray disc player, HD-DVD
player, DVD player, a Digital TV STB (Air or Cable) and other audiovisual equipment.
When using composite
cable. (INPUT 1 or 2)
Blu-ray disc player/HD-DVD
DVD player/Digital TV STB
player/
AV cable
(commercially available)
When using component
cable. (INPUT 1 or 3)
Blu-ray disc player/HD-DVD
DVD player/Digital TV STB
__
player/
Component video cable
p_commercially
_
availabl_e)
Audio cable (commercially available)
,, To enjoy the AQUOS 1080p display capability, connect your external equipment using a component cable and set the
equipment to 1080p output.
,, See page 15 for connecting a Blu ray disc player, HD DVD player, DVD player or a Digital TV STB to the HDMI terminal.
(D-13
Preparation
A VCR, game console, camcorder and other audiovisual equipment can be conveniently connected using the
INPUT 1,2 and 3 terminals.
When
using S-VIDEO
VCR/Garne
Carncerder
cable.
console/
S-VIDEO cable
(commercially available)
AUDIO cable
(commercially available)
When using composite
VCR/Garne
Carncorder
cable.
console/
(commercially available)
__
AV cable
,, The S VIDEO terminal takes priority over the video terminals. (iNPUT 2 only)
It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal. (See page 47 for details.) PCM audio
outputs from the terminal.
To optical digital input of
external audio devices
Optical fiber cable
(commercially available)
(D-
14
Preparation
You can use the INPUT 4, INPUT 5 or INPUT 6 terminal when connecting HDMI equipment.
HDMI cable
(commercially available)
HDMI equipment
• When using an HDMI DVl conversion cable, input the audio signal to AUDK} terminal of iNPUT 6.
• To enjoy the AQUOS 1080p display capability, connect your BkJ ray disc player, HD DVD player or other external equipment
usklg an HDMI cable and set the equipment to 1080p output.
When connecting
to a PC with an analog RGB terminal.
(INPUT 7)
RGB cable
(commercially available)
© 3.5 mm stereo minijack cable
(commercially available)
PC
When connecting
to a PC with an HDMI terminal.
(INPUT 4, 5 or 6)
HDMI cable
(commercially available)
PC
• The HDMI terminals only support digital signal.
is necessary to set the PC correctly to display XGA and WXGA signal. Refer to page 38 to set PC input signals.
PC
Resolutien
720 x 400
VGA
640 x 480
SVGA
800 x 600
XGA
1024 x 768
Horizontal
Frequency
Vertical
Frequency
VESA Standard
31.5 kHz
70 Hz
31.5
37.9
37.5
35.1
37.9
kHz
kHz
kHz
kHz
kHz
60
72
75
56
60
Hz
Hz
Hz
Hz
Hz
O
O
O
O
O
kHz
kHz
kHz
kHz
kHz
kHz
72
75
60
70
75
60
Hz
Hz
Hz
Hz
Hz
Hz
O
O
O
O
O
O
WXGA
1360 x 768
48.1
46.9
48.4
56.5
60.0
47.7
SXGA
1280 x 1024
64.0 kHz
60 Hz
O
SXGA+
UXGA
1400 x 1050
1600 x 1200
64.0 kHz
75.0 kHz
60 Hz
60 Hz
O
O
PC
DDC is a registered trademark of Video Electronics Standards Association.
Power Management is a registered trademark of Sun Microsystems, inc.
VGA and XGA are registered trademarks of International Business Machines Corp.
(D-15
Watching
TV
i
Simple
operations
for watching
a TV program
Press POWER on the TV, or TV POWER on the
remote control unit.
,' POWERindicator(Green):The TV is on. (Aftera few
seconds, a window appears with sound.)
_wer
,, The initial setup starts when the TV powers on for the first
time. if the TV has been turned on before, the EZ Setup will
not be invoked. See page 23 for per%truing EZ Setup from
the Setup menu.
MENU
0
INPUT
Press POWER
remote control
on the TV, or TV POWER
unit.
on the
The TV enters standby and the image on the screen
disappears.
The POWER indicator on the TV turns off.
If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the AC outlet.
SLEEP indicator
,, Weak electric power is still consumed even when the TV is
turned off.
TV POWER (On/Standby)
TV status
h_
c BTL_/s
O AT _ O
SOURCE
F_OTII_
O
N
lsOt:ndby
_
indicator
(POWER)
T U_h_'n_,G_n,
_/Lights off
i
_j
LIGHT
TV status
indicator
(OPC)
REC
CE)
,, See page 26 for details.
TV status
indicator
(SLEEP)
"Off" is selected in SLEEP setting
Lights off
"30", "60", "90" or "120" is selected in SLEEP setting
Lighting (Red)
See page 34 for details.
(D-
16
WatchingTV
When you turn on the TV for the first time, it will automatically memorize the broadcasting channels where you live.
Perform the following steps before you press TV POWER on the remote control unit.
t. Insert the batteries into the remote control unit. (See page 8.)
2. Connect the antenna cable to the TV. (See page 12.)
3. Plug in the AC cord to the AC outlet. (See page 7.)
Channel search
Channel auto search makes the TV look for all
channels viewable in the set area.
When "Air" is selected
in Antenna
setting:
Press 4/1_ to select "Start", and then press
ENTER.
Language setting
Select from among 3 languages: English, French and
Spanish.
OH See_ch
Start
Press A/Y to select the desired language
listed on the screen, and then press ENTER.
When "Cable"
setting:
is selected
in Antenna
Press A/Y to select "Analog & Digital Search
Start" to search both analog and digital
broadcasts or "Analog Search Start" to search
only analog broadcasts, and then press
ENTER.
Antenna
setting
Make sure what kind of connection is made with your
TV when selecting "Air" or "Cable".
Press
Press
OH See_ch
_11/1_ to select "Air" or "Cable".
ENTER to enter the setting.
Example
,, The Channel search will start automatically.
,, To exit the Channelsearchscreen,select "Cancel",
and then press ENTER.
Example
Air
[ 25]
Found
[ 20]
]
!
,, If no channel is found, confirm the type of connection
with your TV and try EZ Setup again. (See page 23.)
made
(D-17
WatchingTV
Method t
Using OH A/V
TV.
You can change channels in several ways.
INPUT
©
CH
@A
on the remote control unit or on the
Method 2
1 Press FLASHBACK
tuned channel.
to switch to the previously
2 Press FLASHBACK again to switch back to the
currently tuned channel.
@v
VOL
FLASHBACK will not work if no channel has been
changed after the TVis turned on.
Method 3
Using remote control buttons 0-9, • (DOT) to select
channels for VHF/UHF/CATV/DIGITAL.
To select a 1 or 2-digit
(e. g., Channel 5}:
channel
number
Press 5_ENT
INPUT
FLASiCBACK
O@
VOL
CH
., When selecting a 1-digit channel number, it is not
necessary to press 0 before the number.
When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
To select a 3-digit channel
(e. g., Channel 115}:
number
Press t_1 _5_ENT
FREEZE
MENU
C®9
To select a 4-digit channel
(e. g., Channel 22.1}:
Press 2 _2_
--
FAVORITECH
number
* (DOT) _I_ENT
--
®®@@
AQUOS
When you enter 0-9 only, channel selection will be made if
there is no operation within a few seconds.
., If you push "0" by itself, nothing will happen.
Complete the above steps within a few seconds.
When you enter 0-9 and - (DOT), channel selection will be
made if there is no operation within a few seconds.
@-
18
WatchingTV
[] Using MUTE on the remote control
Mutes the current sound output.
unit
I/ oH
/i
[] Changing the volume
You can change the volume oil the TV or on the
remote control unit,
INPUT
Press MUTE.
©
., E_) will be displayed on the screen for 30 minutes, and the
sound is silenced.
OH
VOL
C)+
)
!
Mute
Within 30 minutes of pressing MUTE, mute can be
canceled by using one of the methods below.
-- Mute will be canceled if you press VOL +/or MUTE.
Mute will be canceled after 30 minutes have passed.
However, the TV will not suddenly output a loud sound as
the volume level is set to 0 automatically.
[] Using VOL+/• To increase the volume, press VOL+.
• To decrease the volume, press VOL-.
Volume adjustment
[] Using
VOL+/on the TV operates the same as VOL +/the remote control unit.
on
SURROUND
on the
remote
control
unit
SURROUND produces Surround effect from the
speakers. Each time you press SURROUND, the
mode changes between OIl and Off.
Surround sound options
Audio status
On: Makes it possible to enjoy natural, realistic
surround sound.
.................................................................
................................. I......................
Speaker
Variable sound
Off: Outputs the normal sound.
Mute
When "Output Select" is set to "Variable", the indicator on
the screen changes as shown below.
• You can have the same settings by choosing "Surround"
on the menu items. (See page 29.)
See page 37 for details on the Output Select function.
(D-19
Watching
TV
The TV has a feature that allows reception of sound
other than the main audio for the program. This feature
is called Multi-channel Television Sound (MTS). The TV
with MTS can receive mono sound, stereo sound and
Secondary Audio Programs (SAP). The SAP feature
allows a TV station to broadcast other information,
which could be audio in another language or something
completely different like weather information.
You can enjoy Hi-Fi stereo
sound
broadcasts
where available.
to hear.
• Obtain a clearer sound by manually switching to
fixed mono-sound mode.
MTS only operates while in TV mode.
li
R
I_°
P
_
N
FA
_1
/I
shown
to match
the
Y°u
canbelow
change
MTS aS
Examples: when receiving MTS and SAP
(D-
20
Press AUDIO to toggle
between audio modes.
or SAP
• Stereo broadcasts
View programs like live sporting events, shows and
concerts in dynamic stereo sound.
• SAP broadcasts
Receive TV broadcasts in either MAiN or SAP sound.
MAiN sound: The normal program soundtrack (either in
mono or stereo).
SAP sound: Listen to a second language, supplementary
commentary or other information. (SAP is mono sound.)
if stereo sound is difficult
The types of audio transmitted in a digital broadcast
include SURROUND as well as MONO and STEREO.
In addition, it is possible for multiple audio tracks to
accompany a single video track.
STEREO mode
MAIN + SAP mode
STEREO + SAP mode
MONO mode
OPTION
FAVORITE
Example: when receiving Digital
4-
broadcasting
Basic adjustment
settings
[] Using the remote control
Use the following buttons on the remote control to
operate the menu.
Option
MENU
FREEZE
0
--
Example
@
FAVORITE
®®@®
OH
--
®
MENU:
Press to open or close the menu screen.
A/Y/_/D,-:
Press to select a desired item on the
screen or adjust a selected item.
ENTER:
Press to go to the next step or complete
the setting.
RETURN:
Press to return to the previous step.
Item displayed in yellow
• This indicates tile item currently selected.
,, Press ENTER to go to the adjustment screen for this
item.
Item in brackets
• This indicatestile current setting for tile item.
Item displayed in white
,, This indicatesan item can be selected.
I the re_
will change in
I
[ accordance with each menu setting screen. J
[] Using the control panel of the main unit
You can also operate the menu with the control panel
of the main unit.
Button operations on the control panel correspond to
the ones on the remote control as shown below.
Item displayed in gray
• This indicates that the item cannot be selected.
There are various reasons why items cannot be
selected, but the main reasons are as follows:
-- Nothing is connected to the selected input terminal.
--The function is not compatible with the current input
signal.
,, Menu options differ in the selected input modes, but the
operating procedures are the same.
,, The screens in the operation manual are for explanation
purposes (some are enlarged, others cropped) and may
vary slightly from the actual screens.
MENU: MENU on the remote control.
INPUT: ENTER on the remote control.
CN A/V: Cursor Y/A on the remote control.
VOL +/-:
Cursor _/_ on the remote control.
(D- 21
Basic adjustment settings
_
OPC ..............................................................................
Backlight .....................................................................
Contrast ......................................................................
Brightness ..................................................................
Color ...........................................................................
Tint ..............................................................................
Sharpness
..................................................................
Advanced
C,M,S,-Hue
.....................................................
C,M,S,-Saturation
..........................................
Color Temp .....................................................
Active Contrast ...............................................
Fine Motion ......................................................
I/P Setting ........................................................
Film Mode .......................................................
3D-Y/C ............................................................
Monochrome ...................................................
Range of OPC .................................................
Reset ...........................................................................
Page
Page
Page
Page
Page
Page
Page
26
26
26
26
26
26
26
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
27
27
27
27
27
27
28
28
28
28
26
Picture
OPC ..............................................................................
Backlight .....................................................................
Contrast ......................................................................
Brightness ..................................................................
Color ...........................................................................
Tint ..............................................................................
Sharpness ..................................................................
Advanced
C.M,S,-Hue
.....................................................
C.M.S,-Saturation
..........................................
Color Temp .....................................................
Active Contrast ...............................................
Fine Motion ......................................................
I/P Setting ........................................................
Film Mode .......................................................
Monochrome ...................................................
Range of OPC .................................................
Reset ...........................................................................
Page
Page
Page
Page
Page
Page
Page
26
26
26
26
26
26
26
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
27
27
27
27
27
27
28
28
28
26
Page
Page
Page
Page
Page
Page
28
28
28
29
29
28
Page
Page
Page
Page
Page
Page
Page
Page
31
38
32
34
32
33
33
33
,u0,oI
Treble ..........................................................................
Bass .............................................................................
Balance ........................................................................
Surround ......................................................................
Bass Enhancer ............................................................
Reset ...........................................................................
Power
I
[_
PowerControl
[
soto./
EZ Setup ......................................................................
Page 23
CH Setup ..............................................................
Pages 23-24
Antenna Setup-DIGITAL .............................................
Page 24
Input Skip ....................................................................
Page 31
Input Label .................................................................
Page 34
Parental CTRL ......................................................
Pages 41-47
Position ........................................................................
Page 33
Language .....................................................................
Page 33
Reset ............................................................................
Page 33
°or'Co
I
AQUOS LINK Setup .............................................
Pages 54-57
Audio Only ...................................................................
Page 37
Digital Noise Reduction .............................................
Page 37
Input Select .................................................................
Page 30
Output Select ..............................................................
Page 37
Color System ..............................................................
Page 37
Caption Setup .............................................................
Page 40
Digital Caption Info ....................................................
Page 40
Program Title Display ................................................
Page 37
Favorite CH .................................................................
Page 25
Game Play Time ..........................................................
Page 37
Operation Lock Out ....................................................
Page 37
Identification ...............................................................
Page 47 /
Audio Setup .................................................................
Page 47 ]
Software Update ..................................................
Pages 48-49
(D-
22
Input Skip ....................................................................
Input Signal .................................................................
Auto Sync ....................................................................
Input Label .................................................................
Fine Sync .....................................................................
Position ........................................................................
Language .....................................................................
Reset ............................................................................
oCt,Co
!;
AQUOS LINK Setup .............................................
Pages 54-57
Audio Only ...................................................................
Page 37
Digital Noise Reduction .............................................
Page 37
HDMI Setup .................................................................
Page 31
Output Select ..............................................................
Page 37
Game Play Time ..........................................................
Page 37
Operation Lock Out ....................................................
Page 37
"w_"u Digital Setup
• Some menu items may not be displayed depending on the
selected input source.
Basic adjustment settings
You can run EZ Setup again, even after setting up the
preset channels.
If initial setup does not memorize all the channels in
your region, follow the instructions below to manually
memorize the channels.
Antenna
setting
Press MENU to display the MENU screen, and
then press _/_ to select "Setup".
Press _./Y to select "CH Setup",
press ENTER.
Language setting
,_ if you already set the Secret No., input the 4-digit
secret number here. See page 41 for setting a
secret number.
Select from among 3 languages: English, French and
Spanish.
Press MENU to display the MENU screen, and
then press _11/1_to select "Setup".
Press A/Y to select "Air/Cable", and then
press ENTER.
Press A/Y to select "EZ Setup", and then
press ENTER.
- Ifyou alreadyset the Secret No., go to step 3. If
not, skip to step 4.
Press _/_ to select "Air" or "Cable".
Press ENTER to enter the setting.
,nput
the
4-digit
secret
number
byusing
0-g
Press A/Y to select the desired language
listed on the screen, and then press ENTER.
Antenna
setting
Make sure what kind of connection is made with your
TV when selecting "Air" or "Cable".
Press _11/_ to select "Air" or "Cable".
Press ENTER to enter the setting.
Channel
search
in Antenna
Press MENU to exit.
Channel
search
Channel auto search makes the W look for all
channels viewable in the set area.
Repeat steps 1 and 2 in Antenna setting in
Channel Setup.
Press _./Y to select "CH Search", and then
press ENTER.
Channel auto search makes the TV look for all
channels viewable in the set area.
When "Air" is selected
and then
When "Air" is selected
setting:
Press 4/_ to select "Start", and then press
ENTER.
When "Cable" is selected in Antenna
setting:
Press A/Y to select "Analog & Digital Search
Start" to search both analog and digital
broadcasts or "Analog Search Start" to search
only analog broadcasts, and then press
ENTER.
,, The Channelsearch will start automatically.
,, To exit the Channelsearch screen,select "Cancel",
and then press ENTER.
Press _/l_
ENTER.
in Antenna
setting:
to select "Start", and then press
When "Cable"
setting:
is selected
in Antenna
Press A/Y to select "Analog & Digital Search
Start" to search both analog and digital
broadcasts or "Analog Search Start" to search
only analog broadcasts, and then press
ENTER.
,, The Channel search will start automatically.
,, To exit the Channelsearchscreen,select "Cancel",
and then press ENTER.
Press MENU to exit.
Press MENU to exit.
If no channel is found, confirm the type of connection made
with your TV and try EZ Setup again.
,, If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
If no channel is found, confirm the type of connection made
with your TV and try channel search again.
If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
(D" 23
Basic adjustment
settings
Channel memory setting
VOL
CH
FREEZE
In order to receive digital air broadcasts, you need
a digital broadcast antenna. You can confirm the
antenna configuration through the "Antenna Setup DIGITAL" screen.
MENU
0
®
If necessary, adjust the direction of the antenna to
obtain the maximum signal strength.
Signal Strength
--
FAVORITE OH
®®@®
R_OP_
N
Press MENU to display the MENU screen, and
then press _/I_ to select "Setup".
--
Press &/• to select "Antenna Setup DIGITAL", and then press ENTER.
FA_
Press
Press MENU to display the MENU screen, and
then press </1_ to select "Setup".
Press A/•
to select
press ENTER.
"CH Setup",
and then
A/•
to select "Signal
Strength".
• The signal strength of DIGITAL channel is
displayed. The signal information is based on the
current channel.
Signal Strength
• If you already set the Secret No., input the 4-digit
secret number here. See page 41 for setting a
secret number.
Press A/•
to select "CH Memory", and then
press ENTER.
Press A/•
to select ANALOG (Air), ANALOG
(Cable), DIGITAL (Air) or DIGITAL (Cable), and
then press ENTER.
When viewing ANALOG broadcasts:
(_ Press </I_ to select the channel to skip,
and then press • to move down.
(_ Press 4/I_
ENTER,
to select "On", and then press
When viewing DIGITAL broadcasts:
Press A/• to select the channel to skip,
and then press </1_ to select "On".
• On: Skips channels.(Channelselectiondisabled using OH
A/V.)
• Off: Does not skip channels.(Channelselection enabled
using OH A/V.)
Press MENU to exit.
Channel Strength
The channel signal strength can also be checked
separately.
Repeat steps 1 and 2 in Signal Strength in
Antenna Setup - DIGITAL.
Press A/• to select "Channel Strength", and
then press ENTER.
Input the 2-digit channel number to check the
signal strength of the selected channel.
• Makesure the signal is strong enough for each
channel.
Channel
Strength
Press MENU to exit.
• Make sure what kind of connection
is made with your TV.
Press MENU to exit.
• This function is available for DIGITAL (Air) only.
@-
24
Basic adjustment settings
Using Favorite
This function allows you to program 4 favorite
channels, in 4 different categories. By setting the
favorite channels in advance, you can select your
favorite channels easily.
Using FAVORITE ON on the remote
control
CN on the menu screen
You can also set your favorite channels in "Option" on
the MENU screen.
Select the channel you want to register as a
favorite channel.
unit
Press MENU to display the MENU screen, and
then press _/l_ to select "Option".
Select the channel you want to register as a
favorite channel.
Press &/Y to select "Favorite CH", and then
press ENTER.
Press FAVORITE.
Press &/Y to select "Register", and then
press ENTER.
Press &/Y to select "Register", and then
press ENTER.
Press &/Y/_/_
to select the position in the
category, and then press ENTER to register.
Press &/Y/_/_
to select the position in the
category, and then press ENTER to register.
Press MENU to exit.
Deleting
a favorite
channel
Repeat steps 2 and 3 in Using Favorite
on the menu screen.
CN
Press &/Y to select "1 Data Clear", and then
press ENTER.
,, To delete all the favodte channels,select "All Data
Clear", and then skip to step 4.
Deleting a favorite
channel
Press FAVORITE and the favorite channel
screen displays.
Press &/Y to select "1 Data Clear", and then
press ENTER.
• To delete all the favoritechannels,select "All Data
Clear", and then skipto step 4.
Press A/T/_/l_
to select the channel you
want to delete, and then press ENTER.
Press _/_
ENTER.
to select "Yes", and then press
Press MENU to exit.
Press &/V/4/l_
to select the channel you
want to delete, and then press ENTER.
Press _l/l_
ENTER.
to select "Yes", and then press
Yes
(D" 25
Basic adjustment settings
_i_!_!!i_i_!_!_!i_!!_!i_!_iii'iiiiiiiiiiiiiiiiiiiiiiiii_!i_!_!_!!_
¸
Adjusts the picture to your preference
following picture settings.
with the
Press MENU to display the MENU screen, and
then press _11/_ to select "Picture".
Press j,/Y
item.
Baeklight
The screen dims
The screen
brightens
Contrast
For less contrast
For more contrast
Brightness
For less brightness
For more brightness
Color
For less color
intensity
For more color
intensity
Tint
Skin tones become
reddish
Skin tones become
greenish
Sharpness
For less sharpness
For more sharpness
to select a specific adjustment
Press _11/1_to adjust the item to the desired
level.
Press MENU to exit.
., Select "Advanced" and then press ENTER to set "C.M.S.Hue". "C.M.S.-Saturation", "Color Temp.". "Active
Contrast". "Fine Motion", "I/P Setting", "Film Mode", "3D-Y/
C", "Monochrome" or "Range of OPC". See pages 27 and
28.
Automatically
., For resetting all Picture adjustment items to the factory
preset values, press A/T to select "Reset", press ENTER.
press 4/1_ to select "Yes". and then press ENTER.
adjusts
the brightness
of the screen.
Press MENU to display the MENU screen,
then press _1/1_ to select "Picture".
and
Presstose,ect
"oPo"
@ Press
O tose,ect"On"
or"On:
Oisp,ay"
Off
The brightness is fixed at the value set in
"Backlight".
On
Automatically
On: Display
Displays the OPC effect on the screen
while adjusting the brightness of the
screen.
adjusts
Press
MENU
toexit.
., When set to "On". the OPC senses the surrounding light
and automatically adjusts the backlight brightness. Make
sure nothing obstructs the OPC sensor, which could affect
its ability to sense surrounding light.
When set to "On: Display", OPC effect displays on the
screen while the OPC adjusts the screen brightness.
189)- 26
Basic adjustment settings
This TV provides various advanced functions for
optimizing the picture quality.
For a better white balance, use color temperature
correction.
Press MENU to display the MENU screen, and
then press _11/_ to select "Picture".
Press &/Y to select "Advanced", and then
press ENTER.
Press A/Y
to select a specific
item, and then press ENTER.
A/T
(or _1/_)
White with Bluish tone
I
White with Reddbh tone
adjustment
You call select "C.M.S.-Hue", "C.M.S.-Saturatlon",
"Color Temp.", "Active Contrast", "Fine
Motion", "l/P Setting", "Film Mode", "3DH/C",
"Monochrome", or "Range of OPC".
Press
High
Mid-High
Middle
Mid-Low
Low
Automatically adjusts the image contrast according to
the scene.
to select the desired
parameter.
See the table for the sebctabb
parameters.
Press MENU to exit.
Color tone is managed
setting.
using the six-color
adjustment
C.M,S,-Hue
This is a standard to adjust the color either
more reddish or more bluish in tone.
C.M,S.Saturation
Increases or decreases the saturation of a
selected color.
• For resetting all adjustment items to the factory preset
values, press A/T to select "Reset", and then press
ENTER.
Use Fine Motion
to view fast-action
video more
On
For obtaining a clearer image
Off
Normal image
clearly.
• Fine Motion may cause image noise. If this occurs turn the
function "Off".
Converts input signals depending on the type of
images.
Fast
Suitable for fasbmovlng
Slow
Suitable for smooth images with low
amounts of flickers
images
• "I/P Setting" is not selectable when channel display shows
an input resolution of 480P, 720P, or 1080P.
(D" 27
Basic adjustment settings
Automatically detects a film-based source (originally
encoded at 24 frames/second), analyzes it then recreates
each still film frame for high-definition picture quality.
You can adjust the sound quality to your preference
with the following settings.
VOL
On
Detects, analyzes, converts film source
Off
Normal viewing mode
CH
FREEZE
MENU
0
., "Film Mode" does not function when you set the "AV Mode"
to "Game".
"Film Mode" is not selectable when channel display shows
an input resolution of 480P, 720P, or 1080P.
O
_
--
R_N
FAVORITE
CH
6)@@@
Provides high quality images with minimal dot crawl
and cross color noise.
--
Press MENU to display the MENU screen, and
then press _1/1_ to select "Audio".
Slow
For still images
Standard
Normal adjustment
Fast
For moving images
Off (2D}
For Game Mode
., 3D-Y/C is available for input signal from Composite Video
and analog broadcasts (air and cable).
Press A/Y
item.
For viewing a video in monochrome.
On
For viewing in monochrome
Off
Normal color
The brightness level range of the OPC sensor's automatic
adjustments can be set according to your preferences.
The adjustment range of the OPC sensor can be set to a
maximum of + 16 and a minimum of 16.
Max.
15 through
+ 16
IVlin.
16 through
+ 15
The range of OPC settings are active only when the OPC is
set to On.
., The ma_ximum setting cannot be set to a smaller number
than the minimum setting.
., The minimum setting cannot be set to a bigger number
than the me_ximum setting.
Depending on the brightness of the surrounding light, the
OPC sensor might not operate if the adjustment range is
small.
®-
28
to select a specific adjustment
Press 41/1_ to adjust the item to the desired
level.
Treble
For weaker treble
For stronger treble
Bass
For weaker bass
For stronger bass
Balance
Decrease audio from
Decrease audio
the right speaker
from the Deft
speaker
Press MENU to exit.
., Audio menu is grayed out when Output Select is set to
"Variable".
., For resetting all Audio adjustment items to the factory
preset values, press A/T to select "Reset", press ENTER,
press 4/1_ to select "Yes", and then press ENTER.
Basic adjustment settings
Surround function allows you to enjoy realistic "live"
sound.
Press MENU to display the MENU screen, and
then press _11/1_to select "Audio".
Press A/V to select "Surround", and then
press ENTER.
Power control setting allows you to save energy.
No signal off
When set to "Enable", the power will automatically shut
down if there is no signal for 15 minutes.
Press MENU to display the MENU screen, and
then press 41/1_ to select "Power Control".
Press _1/1_ to select "On", and then press
ENTER,
Press A/Y to select "No Signal Off", and then
press ENTER.
Press MENU to exit.
Press _1/1_ to select "Enable", and then press
ENTER.
You can choose Surround by pressing SURROUND on
the remote control unit. (See page 19.)
Audio menu is grayed out when Output Select is set to
"Variable".
,, For some discs, setup may be required on your DVD
player. In this case, please refer to the operation manual of
your DVD player.
• Five minutes before the power shuts down, the
remaining time displays every minute.
Press MENU to exit.
This function allows you to enjoy bass-enhanced
sound.
Press MENU to display the MENU screen, and
then press _11/1_to select "Audio".
• "Disable" is the factory preset value.
,, When a TV program finishes, this function may not operate.
No operation
Press A/Y to select "Bass Enhancer", and
then press ENTER.
Press _1/1_ to select "On", and then press
ENTER.
Press MENU to exit.
off
When set to "Enable", the power will automatically shut
down if there is no operation for 3 hours.
Press MENU to display the MENU screen, and
then press _1/1_ to select "Power Control".
Press A/Y to select "No Operation Off", and
then press ENTER.
Press _1/1_ to select "Enable", and then press
ENTER.
Audio menu is grayed out when Output Select is set to
"Variable".
• Fiveminutes beforethe power shuts down, the
remainingtime displays everyminute.
Press MENU to exit.
,, "Disable" is the factory preset value.
_-
29
Using external equipment
To view external source images, select the input
source from INPUT on the remote control unit or on
the TV.
If the image does not come in clearly from the external
equipment connected to INPUT 1 or 3, you may need
to change the input signal type setting on the "Input
Select" menu.
m
INPUT
FLASaBACK
@0
VOL
Press MENU to display the MENU screen, and
then press _1/1_ to select "Option".
OH
POWER
F_EZE
MENU
0
@
Press A/Y to select "Input Select", and then
press ENTER,
G®g
Press INPUT.
,, A list of selectable sources appears.
,_
Press
INPUT
INPUT1
again to select the input source.
,, An image from the selected source automatically
displays.
,, Each time INPUT is pressed, the input source
toggles.
,, You can also select the input source by pressing
A/T.
,, If the corresponding input is not plugged in, you
cannot change the input. Be sure to connect the
equipment beforehand.
,, See pages 13 to 15 for external equipment connection.
@-
30
Press A/Y to select the signal type you want
to set, and then press ENTER.
,, Ifthe selected signal type is incorrect, imagesare
not displayed or displayedwithout any color.
Press MENU
to exit.
• Tile setting is stored and can be selected on the
"iNPUT SOURCE" menu.
., Refer to your external equipment operation manual for the
signal type.
,, If you set INPUT 1 or 3 to Auto, the TV will automatically
select the input signal.
Setting INPUT 1 or 3 signal selection to "Auto" when
other equipment is connected will result in the following
connection priority.
INPUT 1 or 3:
COMPONENT VIDEO
VIDEO
Using external equipment
To watch an HDMI or PC-IN equipment image,
select "INPUT4", "INPUTS" or "INPUT 6" from
"INPUT SOURCE" menu using iNPUT on the
remote control unit or on the TV.
This setting allows you to skip the HDMI or PC-IN Input
on the Input Selection operation.
Press MENU to display the MENU screen, and
then press 41/1_ to select "Setup".
Press A/Y to select "Input Skip", and then
press ENTER.
Press A/V to select the Input (INPUT 4,
INPUT 5, INPUT 6 or INPUT 7) you wish to
skip, and then press ENTER.
...e INPUT4
Input 4 (HDMI)
Press MENU to display the MENU screen, and
then press _11/1_to select "Option".
Press A/Y to select "HDMI Setup", and then
press ENTER.
Press 4/1_ to select "Yes", and then press
ENTER.
Press MENU to exit.
Press A/V to select the desired item, and
then press ENTER.
Press 41/_ to select the desired setting, and
then press ENTER.
Auto View
Audio
Select
Enable
Disable
Digital
Analog
Set whether or not to use
View Mode based on signal
recognition, including an HDMI
signal.
Select "Digital" for an audio
signal via the HDMI terminal.
Select "Analog" for an audio
signal via the R-AUDIO -L
terminal.
Press MENU to exit.
., Refer to your external
signal type.
., "Audio Select" is only
., When connecting an
to the HDMI terminal,
equipment operation manual for the
available for iNPUT 6.
HDMI-DVI conversion adapted(sable
the image may not come in clearly.
_-
31
Useful adjustment
settings
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimize the image.
For automatically adjusting the PC image.
0
I/
@
Press MENU to display the MENU screen, and
then press 41/1_ to select "Setup".
FREEZE
MENU
E6T
R_.
Press MENU to display the MENU screen,
then press _11/1_ to select "Setup".
Press A/Y to select "Fine Sync.", and then
press ENTER.
and
Press A/V
item.
Press A/V to select "Auto Sync.", and then
press ENTER.
to select the specific adjustment
Press _1/1_ to select "Yes", and then press
ENTER.
,) Auto Sync. starts and "Now adjusting the image."
displays.
!!
Press MENU to exit.
R-Pos,
Centers the image by moving it to the left
or right.
V-Pos,
Centers the image by moving it up or
down.
Clock
Adjust when the image flk_'kers with vertical
stripes.
Phase
Adjust when characters have low contrast
or when the image flickers.
Press 4/1_ to adjust the item to your desired
position.
Press MENU to exit.
,, When Auto Sync. is successful, "Completed" displays. If
not, Auto Sync. failed.
,, Auto Sync. may fail even if "Completed" displays.
,, Auto Sync. may fail if the computer image has low
resolution, has unclear (black) edges, or is moved while
executing Auto Sync.
Be sure to connect the PC to the TV and switch it on
bdore starting Auto Sync.
(D-
32
,, For resetting all Fine Sync. adjustment items to the factory
preset values, press A/T to select "Reset", and then
press ENTER.
,' It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
,, The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrk_'al.
,, The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
position-setting screen.
Useful adjustment settings
For adjusting a picture's horizontal and vertical
position,
Press MENU to display the MENU screen, and
then press _/I_ to select "Setup".
Press A/T to select "Position", and then
press ENTER,
Press A/T
to select "H-Pos," or "V-Pos.".
Example
If complex adjustments are made and the settings
cannot be restored to normal, you can reset the
settings to the factory preset values,
Press MENU to display the MENU screen, and
then press _/I_ to select "Setup".
Press A/T
ENTER,
to select "Reset",
and then press
• If you already set the Secret No., input the 4-digit
secret number here. See page 41 for setting a
secret number.
• "Return to the factory preset values" displays on
the screen.
Press 4/I_
ENTER,
to select "Yes", and then press
• "Now, TV will restart automatically.OK?" displays
on the screen.
Press 4/I_
ENTER,
to select "Yes",
and then press
• "Now initializing..."displays on the screen and
blinks.
• After the reset has completed, the power shuts
off and then comes back on. The screen will have
returned to its original settings.
Press _/I_
position.
to adjust the item to the desired
Press MENU to exit.
• For resetting adjustments to the factory preset values,
press A/T to select "Reset", and then press ENTER.
• When connecting a PC to the HDMI terminal, the image
position will be automatically adjusted. It cannot be
manually adjusted.
• The screen position variable ranges depend on the View
Mode or the signal type. The ranges can be seen on the
positiomsetting screen.
• Adjustments are stored separately according
to input
source.
• The Channel Setup settings will not be changed.
• The Language settings will not be changed.
• The Secret number settings will not be changed.
You can also select a language from the Setup menu.
Select from among 3 languages: English, French and
Spanish.
Press MENU to display the MENU screen, and
then press _1/1_ to select "Setup".
Press A/T to select "Language", and then
press ENTER.
Press A/T to select the desired language
listed on the screen, and then press ENTER,
Press MENU to exit.
(_-
33
Useful adjustment settings
Lets you set the input terminal displayed when using
the INPUT SOURCE menu or channel display.
INPUT
Allows you to set a time when the TV automatically
switches to standby.
FLASHBACK
@©
VOL
OH
FREEZE
Press SLEEP.
MENU
0
O
• The remaining time displays when the sleep timer
has been set.
lSbep
Press INPUT
source.
to select the desired
Timer:
Remaining
30 •
Each time you press SLEEP, the remaining
time switches as shown below.
input
,, When set, the time automatically starts counting
down.
• If you want to adjust the sleep timer, you can
press SLEEP twice then change the time setting.
® Five minutes before the time expires, the
remaining time displays every minute.
Press MENU to display the MENU screen, and
then press _11/1_to select "Setup".
Press A/Y to select "Input Label", and then
press ENTER.
Lrwsq- J
Press A/Y/_/!_
to select the new name for
the input mode, and then press ENTER.
Example
Select "Off" by pressing SLEEP to cancel the sleep timer.
,, The TV will enter standby when the remaining time reaches
zero.
• When the sleep timer is set, its indicator on the TV lights
red.
Press MENU to exit.
,, You cannot change labels if the INPUT SOURCE is TV.
(D-
34
Useful adjustment settings
The following modes are available for HD programs.
Stretch:
Ct_/SAI
SOURCE
pro
FU
CTION
0
LIGHT
FREEZE
MENU
O
O
(ED 0D (}E)
REC
(3D (3D (_D
Press VIEW
Suitable for viewing wide-screen 1.78:1 aspect ratio program,
stretch mode will still show very thin black bands at the top
and bottom of the screen.
Dot by Dot (1080i/p only):
Detects tlqe resolution of the signal and displays an image with
the same number of pixels on the screen.
MODE.
The View Mode menu displays.
,, The menu lists the View Mode options seiectabie
for the type of video signal currently being
received.
Example
Full Screen (720p only):
You can select "Full Screen" only when receiving a 720p
signal.
S.Stretch (Smart stretch):
Suitable for stretching 4:3 programs to fill the screen.
Zoom:
Suitable for viewing wide-screen
Side Bar
in full
screen.
2.35:1 aspect-ratio programs
When using Dot by Dot, it is possible to see noise or
bars around different outer portions of the screen. Please
change view mode to correct this.
Press VIEW MODE or A/T while the View
Mode menu is displayed to select a desired
item on the menu.
•
You call sequentiallyselect a Vbw Mode that has
its own aspect ratio.
Side Bar:
Suitabb for viewing conventional
4:3 programs in their normal
format.
S.Stretch (Smart stretch):
Suitabb for stretching 4:3
programs to fill the screen.
_J
Suitabb for viewing
2.35:1 anamorphic
screen.
Zoom:
wide-screen
DVDs in full
Stretch:
This mode is useful for 1.78:1
DVDs.
When viewing 1.85:1 DVDs, stretch
mode will still show very thin black
bands at the top and bottom of the
screen.
(D" 35
Useful adjustment settings
You can select the screen size.
CBL/SAr
- Connect the PC before making adjustments. (See page
15.)
Selectable screen size may vary with input signal type.
o
DVD
o
SOURCE
FUNCTION
0
LIGHT
G9 (:E) GE)
CE) (3D (3D
REC
Press VIEW
MODE.
,, The View Mode menu displays.
Example
FREEZE
MENU
0
©
G®S
--
FAVORIIE
OH
--
®®@@
Press VIEW MODE or A/T while the View
Mode menu is displayed to select a desired
item on the menu.
Example: Screen size images
input signal
Normal
Zoom
Stretch
Dot by Dot
4:3
Keeps the original
aspect ratio in a full
screen display.
Detects the resolution
For viewing wideAn image fully fills the
screen programs. The screen.
top and bottom of the
image is cropped.
of the signal and
displays an image
with the same
number of pixels on
the screen.
input signal
Stretch
0
An image fully fills the
screen.
36
i
O
16:9
(D-
Dot by Dot
i
Detects the resolution
of the signal and
displays an image
with the same
number of pixels on
the screen.
Useful adjustment settings
Perform the following
items on this page.
steps
to set the Option
Allows
menu
you to select what
Fixed
controls
the audio output.
• Sound via speaker is adjusted with
VOL +/on the remote control
unit or VOL +/on the TV.
• Sound via the AUDIO OUTPUT
terminal is not adjustable and
outputs at a consistent level.
Press MENU to display the MENU screen,
then press _1/1_ to select "Option".
and
Variable
• Sound via the AUDIO OUTPUT
terminal is adjusted with VOL +/on the remote control unit or VOL
+/on the TV.
Press A/T to select a specific adjustment
item, and then press ENTER.
• Sound via speaker is muted.
Press A/T (or _1/1_) to select the desired
setting, and then press ENTER.
Select the video signal system compatible with your
equipment from the list below:
-- Auto/NTSC/PAL-M/PAL-N
Press MENU to exit.
• Skip this step for "Audio Only".
When listening to music from a music program,
can turn the screen off and enjoy audio only.
you
On
Audio is output without screen image.
Off
Both screen images and audio are output.
• The screen image will return to normal when a button
(except those for audio adjustment, such as VOL, MUTE,
SURROUND, AUDIO) is pressed.
• "Color SysterYf' can only be set for the iNPUT 1 VIDEO,
INPUT 2 and INPUT 3 VIDEO.
• If you already set the Secret No., input the 4-digit secret
number here. See page 41 for setting a secret number.
This function displays the elapsed game time so you
do not lose track of the time.
To display the elapsed time, select "GAME" for the
AV MODE before starting the game.
On
The elapsed time is displayed every 30
minutes when you switch to (SAME mode
in external input mode.
Off
No adjustment
Produces a clearer video image.
Off
No adjustment
High
For enhanced Digital Noise Reduction
Low
For moderate Digital Noise Reduction
Select the CH display when changing channels for
digital broadcasting.
Yes
"Program Info." displays
No
"Program Info." does not display
This function locks the operation buttons on the TV
and the remote control.
Off
No adjustment
RC Control Lock
All buttons on the remote control are
locked.
Button Control
Lock
All buttons on the TV, except POWER,
are locked.
• To unlock the buttons on the remote control, press MENU
on the TV, and then select "Off" on the MENU screen.
• To unlock the buttons on the TV, press MENU on the
remote control, and then select "Off" on the MENU screen.
(D" 37
Useful adjustment settings
AV MODE gives you 7 viewing options to choose from
to best match the surrounding environment of the W,
which can vary due to factors like room brightness,
type of program watched or the type of image input
from external equipment.
FREEZE
@
FAVORITECH
6)@@@
R_0P
For a highly defined image in a normal
lighting
[Enhanced Picture Contrast: on]
MOVIE
For a movie
[Enhanced Picture Contrast: ofq
MENU
0
--
STANDARD
_N
--
FA_TF
GAME
Lowers image brightness for easier vbwing
[Enhanced Picture Contrast: ofq
PC
For PC
[Enhanced Picture Contrast: ofq
xvYOC*
Supports the xvYCC international standard
for wide color space.
[Enhanced Picture Contrast: off1
USER
Allows the user to customize settings as
desired. You can set the mode for each
input source.
[Enhanced Picture Contrast: off1
DYNAMIC
(Fixed}
Changes the image and sound settings to
the factory preset values. No adjustments
are allowed.
s SP
Press AV MODE.
• Current AV MODE dbplays.
Press AV MODE again before the mode
displayed on the screen disappears.
* The mode changesas shown below.
When the input source
is TV, iNPUT 1, 2 or 3 terminals
(Example}
[Enhanced Picture Contrast: on]
DYNAMIC
For a clear-cut image emphasizing high
contrast, useful for sports viewing
[Enhanced Picture Contrast: on]
The xvYCC signal allows you to experience colors that
conventional color signals cannot reproduce.
-t
4_
4,
When the input source is iNPUT 4, 5, 6 or 7 terminals
(Example}
Some input signals may have to be registered manually
to display properly.
The pair of input signals (resolutions) in the list below
are not distinguishable when received. In such case,
you have to set the correct signal manually. After
setting once, it will display when the same signal
(resolution) is input again.
1024 × 76B
1360 × 768
• You can only select the "input Signal" on the Setup menu
when receiving one of the 2 input signals listed above.
Press MENU to display the MENU screen, and
then press _/_ to select "Setup".
* You can select a different AV MODE item for each input
mode. (For example, select STANDARD for TV input and
DYNAMIC for INPUT 1 .)
* "Enhanced Picture Contrast" technology detects the source
video characteristics and smoothly adjusts the screen
brightness accordingly to realize deeper black levels.
* "xvYCC" can only be selected when an xvYCC signal is
input using INPUT 4 to 6.
(D-
38
Press A/Y to select "Input Signal", and then
press ENTER,
Press A/Y to select the desired input signal
on the display.
Press MENU to exit.
Useful adjustment
settings
Press CO.
,, This will present the Closed Caption information
display.
Your TV is equipped with an internal Closed Caption
decoder. It allows you to view conversations, narration
and sound effects as subtitles on your TV. Closed
Captions are available on some TV programs and on
some VHS home video tapes at the discretion of the
program provider.
Digital Closed Caption service is a new caption service
available only on digital TV programs (also at the
discretion of the service provide0. It is a more flexible
system than the original Closed Caption system,
because it allows for a variety o1 caption sizes and font
styles. When the Digital Closed Caption service is in
use, it will be indicated by the appearance of a 3-letter
abbreviation that also indicates the language of the
Digital Closed Captions: ENG (English), SPA (Spanish),
FRA (French) or other language codes.
Not all programs and VHS videotapes offer closed
captions. Please look for the "[_]" symbol to ensure
that captions will be shown.
In the Closed Caption system, there can be more than
one caption service provided. Each is identified by its
own number. The "CO1" and "CC2" services display
subtitles of TV programs superimposed over the
program's picture.
In the Closed Caption system, the "Text1" or "Text2"
services display text that is unrelated to the program
being viewed (e.g., weather or news). These services
are also superimposed over the program currently
being viewed.
Press CC while the Closed Caption information
is still on the screen.
,, Pressrepeatedlyuntil you select the desired
closed caption service.
Closed Caption
information
,, Dependingon the number of caption servicesin
the signal being received,you will see information
such as 1/2 or 1/4 displayed.
1/2 means "the first of two services".
Example:
if a program has three services (DigitalCC(ENG),
CC1 and Text1), the closed caption displaywill
toggle in this sequence:
,, The CC button keeps a record of the last service
selected inits memory.
if the lastclosed caption mode (e.g. 1/3ENG)you
selected is not availablefor the next program, or
on another channel,the closed caption service
that is availableis automaticallyselected, and this
serviceappears in parentheses,e.g. "1/3(CC1)".
Closed Caption servicesthat appear in
parentheseswill not be stored in the CC button's
memoryas your last selected service. Only
servicesthat you haveselected with the CC
button are stored.
Examples:
In a case where there are two closed caption
services provided, (for instance, Digital
CC(ENG) and CO1), and Digital CC(ENG)
is displayed as your current selection, if
Digital CC(ENG) is not broadcast for the next
program, the other closed caption service,
CC1, will be displayed in parentheses.
A closed caption service appears in
parentheses because the service you selected
is not available and a different service is
displayed on your screen. "1/1(CC1)" is
displayed instead of "I/2/ENG".
,, See page 40 for detailed closed caption settings.
,, When the program contains no closed caption, "--"
displays in the closed caption information.
,, If the language code, e.g. "ENG", is not found on Digital TV
programs, "--" will be shown.
Four kinds of closed caption service (CC1, CC2, Text1,
Text2) are potentially available, but a broadcast may contain
none or only some of these services at the discretion of the
program provider.
(D" 39
Useful adjustment settings
Selectable items available for "Font Style",
This function allows you to adjust the closed caption
screen appearance to suit your preference.
000
®00
CO®
(Z)®Q
O
I/
INPUT
@
FREEZE
MENU
Default
The font specified by broadcasting station
or default font.
Type 0
Proportional font used in the MENU
screen.
Type 1
Monospaced with serifs.
Type 2
Proportionally spaced with serifs.
Type 3
Monospaced without serifs.
Type 4
Proportionally spaced without serifs.
Type 5
Casual font type.
Type 6
Cursive font type.
Type 7
Small capitals.
_' A£H_¢K
O0
Press MENU to display the MENU screen, and
then press _11/1_to select "Option".
Press A/Y to select "Caption Setup", and
then press ENTER.
Press J,/V
item.
to select a specific adjustment
This function allows viewing of digital closed caption
information for the digital broadcast program being
viewed.
• You can adjust 7 items here;they are,
(_ "Oaption Size",
(_ "Font Style",
Press MENU to display the MENU screen, and
then press 41/11_to select "Option".
"Foreground Oolor",
"Foreground Opacity",
(_ "Background
Color",
(_ "Background
Opacity" and
Press A/T to select "Digital Caption Info.",
and then press ENTER.
"Character Edge".
Caption
Size
'_E
Default
_ _,
The digital closed caption information for the
program being viewed is displayed in a list,
and then press ENTER.
Press _11/1_to select the desired parameter.
("easyreader")displays easy-to-read captions for children.
Press MENU to exit.
For resetting adjustments to the factory preset values,
press A/T to select "Reset", and then press ENTER.
The default value depends on the broadcasting station.
Q-
40
Press MENU to exit.
This list is not displayed for analog broadcasts or external
input audio/video.
This information is not included in CC1, CC2, Text1, or
Text2, and is not displayed in a list.
Useful adjustment settings
Input the same 4-digit number on the
"Reconfirm" screen as in step 4 to confirm.
New Secret No,
Allows you to use a secret number to protect certain
settings from being accidentally changed.
IMPORTANT:
Three conditions must be met to enable the V-Chip (see
pages 41 to 47):
Secret No. is registered.
V-Chip/V-Chip (DTV Only) settings have been
made.
Press RETURN to start configuring the V-Chip
settings. (See pages 44 and 47 for details.)
"Status" is set to "On".
Setting a secret number
Press MENU to exit.
Press MENU to display the MENU screen,
and then press _/1_ to select "Setup".
Setting parental control status
Press A/I' to select "Parental CTRL", and
then press ENTER.
Press A/T to select "Secret No.", and then
press ENTER.
Used to enable or disable the parental control function.
Repeat steps 1 and 2 in Setting a secret
number.
• The secret number setting menu displays.
,nput
the
4-digit
eecret
number
byusing
0-g
Press A/I'
ENTER,
Select "New Secret No.", and then press
ENTER,
to select "Status", and then press
Press 4/I_ to select "On" or "Off", and then
press ENTER,
• Select "On" to enable and "Off"to disable Parental
CTRL.
Input the new 4-digit secret number by using 0
-9.
New Secret
No.
Status
Press MENU to exit.
• You can skip steps 1 and 2 above while in the Parental
CTRL screen.
• The "V-Chip (DTV Only)" will only be selectable when a new
rating system can be downloaded via digital broadcasting
in the U.S.
(D" 41
Useful adjustment settings
Changing the secret
Allows you to change
number
our current secret number.
Clearing the secret number
Allows you to clear your secret number.
COO
FREEZE
©
@
a secret
• The secret number setting menu displays.
QQ®
G) OQ
i'
O0
Repeat steps 1 and 2 in Setting
number.
Repeat steps 1 and 2 in Setting
number.
MENU
Input the 4-digit secret number by using 0-9.
iiiiii_
a secret
Hiiii ii _
Press A/T to select "Secret No.", and then
press ENTER.
,, The secret number setting menu displays.
Input the 4-digit secret number by using 0-9.
Press A/T to select "Secret No. Clear", and
then press ENTER.
Press A/Y to select "Secret No.", and then
press ENTER.
Press _/_ to select "Yes", and then press
ENTER.
,, Your secret number is cleared.
Press A/V to select "New Secret No.", and
then press ENTER.
Secret No. Olea_
Input the old 4-digit secret number by using 09.
New gecret No.
Press MENU to exit.
Input the new 4-digit secret number by using 0
--g.
New Secret No.
Input the same 4-digit number on the
"Reconfirm" screen as in step 6 to confirm.
New Secret No.
Press MENU to exit.
(D- 42
., See page 41 for re-registering a new secret number after
being cleared.
• As a precautionary
measure, make a note of your
secret number and keep it in a familiar place,
If the secret number is cleared, the Status setting
automatically sets to "Off". "V-Chip" and "Status" will not
be selectable from the menu.
Useful adjustment settings
V-CHIP is an electronic filtering device built into your TV. This tool gives parents a great degree of control over
broadcasts accessed by their children, it allows parents to select programs judged suitable for child viewing while
blocking ones judged not suitable. It does so automatically once you activate the V-CHIP feature in your TV.
"V-Chip" and "Status" will not be selectable from the menu if you do not first configure your secret
number. (See page 41 for Secret number setting for parental control.)
• The U.S. has two rating systems for viewing content: TV Parental Guidelines and movie ratings.
• The TV Parental Guidelines work in conjunction with the V-CHIP to help parents screen out inappropriate
television shows from their children.
• Movie ratings are used for original movies rated by the Motion Picture Association of America (MPAA) as
watched on cable TV and not edited for television. The V-CHIP can also be set to block MPAA-rated movies.
Voluntary
movie rating system (MPAA)
G
General audiences. All ages admitted.
PG
Parental guidance suggested. Some material may not be suitable for children.
PG-13
Parents strongly cautioned. Some material may be inappropriate for children under 13.
R
Restricted. Under 17 requires accompanying
jurisdictions).
NC-17
No one 17 and under admitted.
X
X is an older rating that is unified with NC-17 but may be encoded in the data of older movies.
Age
parent or adult guardian (age varies in some
[EXAMPLE _
If you select "PG- 13", this will automatically block the higher
ratings "R", "NC-17" and "X".
MPAA
,, Voluntary movie rating system only uses an age-based rating.
TV Parental Guidelines
Content
Suggested
age
FV
(Fantasy
violence)
V
(Violence)
L
(Adult
language)
D
(Sexually
suggestive
dialog)
TV-Y (All children)
%
%
%
TV-Y7 (Directed to older children)
x
%
%
TV-G (General audience)
%
%
TV-PG (Parental Guidance suggested)
x
x
x
x
TV-14 (Parents strongly cautioned)
x
x
x
x
TV-MA (Mature audience only)
x
x
x
S
(Sexual
situation)
_: The content rating can be set, but this rating is not normally broadcast by TV stations.
× : Content rating can be set.
(D" 43
Useful adjustment settings
Voluntary
movie rating system (MPAA)
FR£EZE
®00
®QO
_/ OQO
TV Parental Guidelines (TV Guidelines)
MENU
0
@
......
Repeat steps 1 to 4 in Voluntary
rating system (MPAA).
movie
Press A/T to select "TV Guidelines", and
then press ENTER.
OO
Press MENU to display the MENU screen, and
then press _11/1_to select "Setup".
Press A/Y
to select
then press ENTER.
"Parental
CTRL",
Press ._,/Y to adjust the item to your desired
position. "_" indicates the item is blocked.
,, The setting automatically enters "Block" for any
ratings below your selection.
and
,, The secret number setting menu displays only
when "Secret No." is set. (See page 41 .)
_, "V-Chip" and "Status" will not be seleetable from
the menu if you do not first configure your secret
number. (See page 41 .)
Example
TV Guidelines
,nput
the
4-digit
seeret
number
byusing
0-g
.....
_iiiii_iiiiiiiiiii_,
,¸
Press _,/Y to select "V-Chip", and then press
ENTER.
When setting an individual content-based
rating item, do as follows:
1_ Press I_ or ENTER to access blocked
content items from the currently selected
age-based rating item.
(_ Press A/T to select an individual item,
and then press ENTER to unblock it ("_"
is removed). Repeat the same steps for the
other items.
Press A/Y
ENTER.
to select "MPAA", and then press
Press A/T
to adjust the item to your desired
position. "_" indicates the item is blocked.
Press
(_ Press _ or RETURN to register after all
individual content rating items are set.
Example
TV Guidelines
RETURN.
The setting automatically enters "Block" for any
ratings below your selection.
,, If Status is not set to "On", the configuration
settings will not work. (See page 41 .)
Example
• If Status is not set to "On", the configuration
settings will not work. (See page 41 .)
MPAA
Press MENU to exit.
Press MENU to exit.
(D- 44
Useful adjustment settings
Canadian
Rating Systems
• The W rating systems in Canada are based on the Canadian Radio-Television and Telecommunications
Commission (CRTC) policy on violence in television programming.
• While violence is the most important content element to be rated, the structure developed takes into
consideration other program content like language, nudity, sexuality and mature themes.
• When setting the V-CHIP on the Canadian system you can choose either the Canadian English ratings or the
Canadian French ratings.
Canadian
Age
English ratings
E
Exempt: Includes news, sports, documentaries
music videos, and varbty programming.
C
Children: Intended for younger children under the age of 8 years. Pays careful attention to themes
that could threaten their sense of security and well-being.
C8 +
Children over 8 years old: Contains no portrayal of violence as the preferred, acceptable, or only
way to resolve conflict; nor encourage children to imitate dangerous acts which they may see on
the screen.
G
General: Considered acceptable for all age groups. Appropriate vbwing for the entire family,
contains very little violence, physical, verbal or emotional.
PG
Parental Guidance: Intended for a general audience, but may not be suitable for younger children
(under the age of 8) because it could contain controversial themes or issues.
14+
Over 14 Years: Could contain themes where violence is one of the dominant elements of the
and other information programming; talk shows,
storyline, but it must be integral to the development of plot or character. Language usage could
be profane and nudity present within the context of the theme.
18+
Canadian
French
Adults: Intended for vbwers 18 years and older and might contain depictions of violence, which
while related to the development of plot, character or themes, are intended for adult vbwing.
Could contain graphic language and portrayals of sex and nudity.
ratings
E
Exempt programming.
G
General: All ages and children, contains minimal direct violence, but may be integrated into the
plot in a humorous or unrealistic manner.
8arts +
General but inadvisable for young children: May be vbwed by a wide public audience, but could
contain scenes disturbing to children under 8 who cannot distinguish between imaginary and real
situations. Recommended for vbwing with parent.
13ans +
Over 13 years: Could contain scenes of frequent violent scenes and therefore recommended
viewing with parent.
16ans +
Over 16 years: Could contain frequent violent scenes and intense violence.
1Sans +
Over 18 years: Only for adult viewing. Could contain frequent violent scenes and extreme violence.
Age
for
_-
45
Useful adjustment settings
Canadian
English ratings
Canadian
French ratings
Repeat
steps
l to4,nCanadian
E°g,sh
QQQ
®@®
®Q®
dbO@
ratings.
INPUT
Press A/Y to select "Can. French Ratings",
and then press ENTER.
FtASH&_CK
OO
Press MENU to display the MENU screen, and
then press _11/_ to select "Setup".
Press A/Y
to select
then press ENTER.
"Parental
CTRL",
and
,, Secret number setting menu displays only when
"Secret No." is set. (See page 41 .)
"V-Chip" and "Status" will not be selectable from
the menu if you do not first configure your secret
number. (See page 41 .)
Press ._,/Y to adjust the item to your desired
position. "_" indicates the item is blocked.
,, The setting automatically enters "Block" for any
ratings below your selection.
,, If Status is not set to "On", the configuration
settings will not work. (See page 41 .)
Example
Input the 4-digit secret number by using 0-9.
J SecretNo.
_]
Press _,/Y to select "V-Chip", and then press
ENTER,
Press A/Y to select "Can. English Ratings",
and then press ENTER.
Press A/Y
to adjust the item to your desired
position. "_," indicates the item is blocked.
,, The setting automatically enters "Block" for any
ratings below your selection.
,, if Status is not set to "On", the configuration
settings will not work. (See page 41 .)
Example
Can. English Ratings
Press MENU to exit.
(D- 46
Press MENU to exit.
Useful adjustment settings
When the V-CHIP BLOCK is working and censors a
broadcast, "V-CHIP HAS BEEN ACTIVATED." displays.
Press ENTER while the V-CHIP is working,
and then the secret number setting menu
displays.
Input the 4-digit secret number by using 09. At this time V-CHIP BLOCK temporarily
releases.
This setting allows you to optimize the settings of
Digital broadcasting.
You can output digital audio to an AV amplifier or
similar device whose DIGITAL AUDIO INPUT terminal
is connected to the DIGITAL AUDIO OUTPUT terminal
on the W. Please select an audio output format
compatible with the audio format of the program you
are watching and the equipment connected.
Press MENU to display the MENU screen, and
then press _11/_ to select "Digital Setup".
Press A/Y to select "Audio Setup", and then
press ENTER.
You can reactivate the temporarily released V-CHIP
BLOCK as shown below.
Method 1:
Press A/Y to select "PCM" or "Dolby Digital",
and then press ENTER.
Select "Status" setting from the Parental CTRL menu
to reactivate BLOCK. (See page 41 .)
Method 2:
Select "V-Chip" setting ("MPAA", "TV Guidelines",
"Can. English Ratings" or "Can. French Ratings")
from the Parental CTRL to reactivate BLOCK. (See
pages 44 and 47.)
Method 3:
Switch off the TV power.
Performing any of the three above will activate the V-CHIP
BLOCK.
PCM
The optical output terminal outputs audio
signal in PCM form. Ifyour digital audio
systemdoes not support Dolby Digital,
select "PCM".
Doiby Digital
The optical output terminal outputs audio
signal in Dolby Digitalform. It reproduces
sound from surround program of digital.
Press MENU to exit.
Press MENU to display the MENU screen, and
then press _/l_ to select "Digital Setup".
Press A/Y to select "Identification", and then
press ENTER.
The current version of the TV software is
displayed.
(D- 47
Useful adjustment settings
During the data checking, "Checking" blinks.
This function allows software updates by inserting a
USB memory device with the update file into the USB
terminal on the TV.
Regarding how to obtain the soRware update file,
please
call 1-800-BE-SHARP.
_REEZZ
MENU
0
@
¢
OQO//
g
©©
- The current version of the TV software and the
version of the update file on the USB memory
device are displayed. To update the TV software
with the update file, select "Yes", and then press
ENTER.
Example
® Do not remove the USB memory device or unplug the
AC cord while the software is being updated,
Insert the USB memory device with the update
file into the USB terminal on the TV.
,, If the USB memory device is not properly installed
or the correct update file cannot be found on
the USB memory device, an error message is
displayed.
Check the file on the USB memory device, and
then reinsert the USB memory device correctly.
Press MENU to display the MENU screen, and
then press _11/1_to select "Digital Setup".
Press A/Y to select "Software Update", and
then press ENTER.
Ifyou alreadyset tile Secret No., go to step 4.
Software
Input the 4-digit
Update
secret number
by using 0-9.
Press ENTER to start checking the data in the
USB memory device.
(D- 48
Useful adjustment settings
Press ENTER to start updating.
* The screen becomes dark for a while until the
After the screen shown below is displayed,
sress ENTER.
update screen can be displayed. Please wait for
the update screen to appear. Do not unplug the
AC cord.
Remove the USB memory device.
!
Example
* If you accidentally unplugged the AC cord or
removed the USB memory devk_'e,reinsert the
USB memory device and plug in the AC cord.
The update process is restarted.
When the soRware is successfully updated, a
screen is displayed indicating that the update
process is completed.
After this screen is displayed, the TV
automatically turns off and then turns on again.
Example
* If the update has failed, check the file in the USB
memory device and try Software Update again.
(D" 49
Other viewing options
Allows you to capture and freeze a moving image that
you are watching.
FREEZE
You can operate the connected AV products (AV
Receiver, Cable Box, SAT tuner, DTV, VCR, DVD, LD)
using the presetting manufacturer function of your
remote control unit.
MENU
®_o
G®9
E6T
--
PAVORITECH
®®@@
TV
TV
VCR
C BL/SAT
%D
AUDIO
FUNCTION
0
@
0
SOURCE
0
LIGHT
--
E) []D E]
[Z] [3D CD
[_E] ED @
REC
AqUOS
Press FREEZE.
• A moving image is captured.
Press FREEZE again to cancel the function.
(Z)
Q
INPUT
FLASHBACK
CO
., When this function is not available, "No displaying still
image available." will display.
The still image automatically goes out after 30 minutes.
., If you are using the freeze function and a broadcast
activates the V-CHIP BLOCK, the freeze function will be
cancelled and a V-CHIP BLOCK message will appear.
Presetting manufacturer
Press FUNCTION
device lights up.
codes
until the LED for your
After the LED for your device lights up, press
FUNCTION and DISPLAY at the same time
to enter the code registration mode. The LED
will blink.
Press 0-9 to enter the manufacturer code. (See
page 51 .)
,, Preset mode is finished once the LED no longer
lights up.
After registering the code, the LED will stop
blinking then turn off after one second. (If you
perform an incorrect operation, the LED will
blink quickly then turn off.)
(D-
50
Other viewing options
Manufacturer codes
VCR BRAND
Akai
Audio
Broksonic
Canon
Capehart
Craig
Curtis Mathis
Daewoo
DBX
Dynatech
Emerson
Fisher
Funai
G.E.
Goldstar
Hitachi
Instant Replay
JC Penney
JVC
Kenwood
Lloyds
Magnavox
Magnin
Marantz
Memorex
Minolta
Mitsubishi
Montgomery Ward
Multitech
NEC
Panasonic
Pentax
Philco
Philips
Pioneer
QUASAR
RCA
Realistic
Samsung
Sanyo
Scott
Sears
Sharp
Shintom
Sony
Sound Design
Sylvania
Symphonic
Tatung
Teac
Teknika
Thomas
TMK
Toshiba
Video Concepts
Yamaha
Zenith
REMOTE
CONTROL CODE
NUMBER
25, 26, 37
15, 22, 30
32
O4
34
10, 31
04
34
15, 22, 30
29
21,32, 35
09, 10, 11
28, 29
O4
24
06, 47
04
04, 06, 24,
15, 41,42,
14, 15
29
04, 05, 08
31
30
04, 10, 24,
O6
17, 18, 39,
02, 43
29
15, 22, 30
04, 44, 45,
05, 06
04, 06
04, 05, 08
46
O4
06, 07, 33,
01,02, 10,
23, 31
10, 14, 52
20
06, 11,24
01,02, 03
36
12, 13, 38
29
05, 08
29
15
15, 29
27, 29
29
21
19, 20
3O
15, 29, 30
16
DVD/LD BRAND
Denon
JVC
Kenwood
Magnavox
Marantz
Mitsubishi
Panasonic
Philips
Pioneer
Proscan
RCA
Samsung
Sharp
Sony
Toshiba
Yamaha
Zenith
REMOTE
02
09
21
04
04
06
02,
04,
08,
03
03,
07,
01,
05,
04
02
04
CONTROL
NUMBER
CODE
22
23
11,20
24
12
10
25
30
53
CA'IV/SAT
29
40, 48
49, 50
51
24
BRAND
Anvision
Cable Star
Eagle
General Instrument
Jerrold
Magnavox
Motorola
NEC
Oak Sigma
Panasonic
Philips
Pioneer
Randtek
RCA
Scientific Atlanta
Sony
Viewstar
Zenith
REMOTE
CONTROL
NUMBER
CODE
04, 05
04, 05
O5
02, 03, 07, 12, 13, t4,
19, 22
02, 03, 07, 12, 13, t4,
22, 31, 32, 33, 34, 35,
36, 37, 38, 39, 40
04, 05, 09, 14, 17, 18,
20, 21,24, 25
47
42
8
16, 23
04, 05, 09, 15, 17, 18,
20, 21,24, 25
08, 10, 29, 30, 43*, 46
04, 05
16, 27, 44", 45*
01,26
28
04, 05, 09, 15, 17, 18,
20, 21, 24, 25
06, 41
,, Numbers marked with * are SAT codes, all others are
CATV codes.
AUDIO BRAND
Sharp
REMOTE
CONTROL
NUMBER
CODE
01
(D" 51
Other viewing options
[] Cable control buttons
O
"@"
s0u_c_
LIGHt
When the FUNCTION is set to CBL/SAT, the cable converter connected to
the TV can be operated using t to 4.
__
_oe_
t
SOURCE POWER
2
Turns the cable converter power on and off.
0-9
3
Press a button (or buttons) that corresponds to the channel that you wish
to watch.
FLASHBACK *
C_D (3D CD
oOOi
--
®®®i
®®®i
Press to switch between the current channel and the channel you were
watching immediately before.
INPUTr L_S_ACK
OO--
4 CH A/V
Press CHA
_ZE
MEnU
or CH v
to tune in to a higher or lower channel.
* Some manufacturers do not preset FLASHBACK.
C®9
• CABLE and SAT cannot be selected at the same time.
®®@®
AQUOS
[] SAT control
_v
TV
V_R
0:,
AUDIO
t
ooo
C_ SA_rDW FU_CTI0_
SOURCE
buttons
SOURCE POWER
Turns the cable converter power on and off.
LIGHT
__
2
C_
@
_D
@
0-9, • (DOT)
Press a button (or buttons) that corresponds to the channel that you wish
to watch,
C_
@
3
2_
ENTER, A/Y/_I/_
ENTER: Press to activate the selected function.
A/_'/4/ll_:
Press the button to select items on the SAT GUIDE screen
or SAT MENU screen.
O0
,, CABLE and SAT cannot be selected at the same time.
--3
_AVO_IT_0_
®®©®
AQUOS
(D-
52
Other viewing options
[] VCR
8
control
buttons
The remote control unit button will function
of the remote control unit is set to VCR.
Tv o_ v2 ,,u2o
REC
when the FUNCTION
Press INPUT until the input connected to the VCR is selected. The following 1 to 8
can be used to control the VCR.
i
=_
as follows
J|
ca A/V
Press to select the channel of the TV tuner on the VCR.
2
SOURCE
POWER
Turns the power of the VCR on and off.
@@(i)
Q(D(D
(2)@(i)
(D (g? @
@©
s il
Sets pauses and still pictures.
4
44
Rewinds the tape and allows picture search.
5 II
Stops the tape transport.
6
F_F_ZE
Starts recording.
M_NU
o d_5:2_
O
REC
7 t)'t_
Rapidly advances
y _::D>'S"
the tape and allows picture search.
8 !_
Starts playback.
AQUOS
3
10
[] DVD control
buttons
The remote control unit button will function as follows when the FUNCTION
of the remote control unit is set to DVD.
Press INPUT until the input connected to the DVD player is selected. The following 1
to 10 can be used to control the DVD player.
Pressing quickly once takes you to the start of the next chapter,
press it, you move ahead to the start of the next chapter.
Each time you
2 14141
Pressing quickly once takes you to the start of the chapter currently playing.
Each time you press it, you move back to the start of the prevk)us chapter.
3
SOURCE
POWER
Turns the power of the DVD player on and off.
4 ||
Sets pauses and still pictures.
5 _141
Hold down to go in reverse.
6 III
Playback stops when pressed.
With some DVD players, pressing the button twice may open the disc tray.
7
MENU
When this button is pressed, the DVD menu will display.
8
ENTER,
&/_'/4/_
ENTER: Press to activate the selected function.
A/T/4/I_:
Press the button to select items on the DVD
MENU screen.
Hold down to fast forward.
10 II),
Starts playback.
(D" 53
Other viewing options
What's AQUOS LINK?
* Using the HDMI CEC (Consumer Electronics Control) protocol, with AQUOS LINK you can interactivelyoperate
compatible system equipment (Blue-ray Disc equipment, AV amplifier, DVD),
* By connecting AQUOS LINK-compatible devices with HDMI-certified cables to the TV, you can control a
recorder or AV amplifier using the remote control of the TV.
* AQUOS LINK allows you to operate the HDMI-connected equipment with one remote control.
DIGIT/_
- AUOI(
OUIPL
E
I (e)
I ill
Optical
fiber cable
(commercially
k (e)
available)
HDMI cable
(commercially
(commercially
available)
l
_
HDMI cable
-i_n'll
®
,®
AQUOS BD Player
(available Fall '07)
•
•
•
•
AQUOS LINK-compatible
Audio system
Point the remote control toward the TV, not to connected HDMI equipment.
Video noise may occur depending on the type of HDMI cable used. Make sure to use a certified HDMI cable.
Up to 3 HDMI recording equipment and one AV amplifier can be connected using this system.
These operations affect the HDMI equipment selected as the current input source. If the equipment does not operate, turn on
the equipment and select the appropriate input source using INPUT.
0 o
IV
TV
V_
A[_IO
You can operate AQUOS LINK-compatible devices with the remote control
unit when the FUNCTION of the remote control unit is set to TV.
CB_/SA I/OV/I_U!ICTIO_
SOURCE
@
LIGHT
REC STOP and OPTION buttons will function only when AQUOS LINK is
used.
•
One Touch Play
While the TV is in standby mode, it automatically turns on and plays back the
image from the HDMI source.
FR_EZF
MENU
o
Q
• One Touch Recording
Press REC while you are viewing a broadcast recieved with the AQUOS
LINK-compatible recorder, The AQUOS LINK automatically recognizes the
connected HDMI device and starts recording,
•
Single remote
control
The AQUOS LINK automatically recognizes the connected HDMI device and
you can control the TV and the devices as if using a universal remote control.
• Control the AQUOS LINK-compatible
Set the volume of AQUOS LINK-compatible
®-
Audio system
Audio system.
• The above description is an exampleof the AQUOS LINK function.
• The steps in "AQUOSLINK Setup" on page 55 need to be completed beforehand.
• Referto this operation manualand the operation manualof the AQUOS LINK device to be usedwith this TV.
54
Other viewing options
If this is activated, the One Touch Play function is
enabled.
While the 77/is in standby mode, it automatically turns
on and plays back the image from the HDMI source.
Press MENU to display the MENU screen, and
then press _/I_ to select "Option".
Press A/T to select "AQUOS LINK Setup",
and then press ENTER,
Press A/I' to select "Auto Power On", and
then press ENTER.
When multiple AQUOS LINK-compatible devices are
connected, this function allows you to set the recorder
for recording when you press REC on the TV's remote
control,
Press MENU to display the MENU screen, and
then press _/I_ to select "Option".
Press A/T to select "AQUOS LINK Setup",
and then press ENTER.
Press A/T to select "Selecting Recorder",
and then press ENTER.
Auto Power On
Press MENU to exit.
Press </I_
ENTER,
to select "Yes", and then press
Press MENU to exit.
Example : when connecting AQUOS LINK-compatible
recorder via AQUOS LINK-compatible Audio
system
When an AQUOS LINK-compatible Audio system
or other equipment is connected between the TV
and recorder, "Sub" is displayed.
(D" 55
Other viewing options
You can switch the media (HDD or DVD) for playback
or recording on the AQUOS LINK-compatible recorder.
Oo
c_/sAr
%1/
F{JI4¢TI0_
O
SOURCE
LIGHT
This function allows easy one-touch recording of the
program being viewed on the TV to AQUOS LINKcompatible equipment with a recording function by
simply pressing REC on the remote control.
Prepare the connected AQUOS LINK-compatible
recorder for recording. Check the following items.
• Make sure that the antenna cable is connected.
• Check that there is sufficient available space on the
recording media (HDD, DVD, etc.).
• On the TV, use "AQUOS LiNK Setup" and "Model select" to
select the equipment for recording.
• By default, the recorder connected to INPUT 5 is selected
for recording.
Press REC to start recording,
vo_
OH
FR_EZE
MENU
O
O
FAVORITE
CH
®@®@
_ECSTOP OPTION
Oco
s(_o
Press REC STOP to stop recording,
FAVORITE
C3
Co c3 CD
AUDIO/*V_00E CC
Press OPTION to display the AQUOS LINK
MENU screen.
Press A/I' to select "Media change", and
then press ENTER.
Media
• When you are viewing a broadcast received with
the AQUOS LINK-compatible recorder selected in
"Model select", recording to the AQUOS recorder
of the broadcast being viewed starts.
• When you are viewing a broadcast received
with equipment other than the AQUOS LINKcompatible recorder selected in "Model select" or
other external input equipment, pressing REC on
the remote control does not start recording.
Press OPTION to display the AQUOS LINK
MENU screen.
Press _,/T to select "Recorder EPG", and
then press ENTER.
• The recorder's EPG is displayed.
Change
Select the desired
You can call up the CEC-compatible recorder's EPG
and preset timer recordings using the TV's remote
control.
media such as DVD or HDD.
• The Media type toggles every time you press
ENTER in "Media change".
• Select the media to be operated by the player.
Select the program to record.
• You can use A/T/_/I_,
ENTER,
RETURN, EXIT and the coloured buttons.
• Refer to the operation manual of the recorder for details.
(D-
56
Other viewing options
AQUOS LINK allows you to operate the HDMIconnected equipment with one remote control.
Press
•
to start playing
back a title.
• The last played program is played back. You can use
following buttons during broadcast viewing.
Youcanselectto listento the TVsoundonlyfromthe AQUOSLINKcompatibleAudiosystemandmanuallychangeitssoundmode,
Press OPTION to display the AQUOS LINK
MENU screen.
Press A/IF to select "By AQUOS AUDIO SP",
and then press ENTER.
SOURCE
POWER
•._,
•
• •
Turns the power of the HDMI connected
devices on and off.
Hold down to go in reverse.
Starts Playback.
Hold down to fast forward.
•
Playback stops.
II |
Sets pauses and still pictures.
By AQUOS AUDIO SP
Pressing quickly once takes you to the start
of the chapter currently playing. Each time
you press it. you move back to the start of
the previous chapter.
_1_
Pressing quickly once takes you to the start
of the next chapter. Each time you press
it. you rnove ahead to the start of the next
chapter.
This section explains how to play back a title in the
AQUOS BD Player.
Power on the AQUOS BD Player, select
appropriate external input.
Press OPTION to display the AQUOS LINK
MENU screen.
I
• The sound from the TV speaker is muted and
only the sound from the AQUOS LINK-compatible
Audio system is audible.
• You can use VOL+/and MUTE.
Select "By AQUOS SP", and then press
ENTER to listen to the TV sound.
Press OPTION to display the AQUOS LINK
MENU screen.
Press A/IF to select "Sound mode change",
and then press ENTER.
Press A/T to select "Top menu/title list", and
then press ENTER.
Top menu/title list
• The sound mode changes every time you press ENTER.
• Refer to the operation manual of the AQUOS
LINK-compatible Audio system for details.
• The title list data from the connected AQUOS BD
Player displays.
Select the title with A/IF/_/•,
press • to start playback.
and then
(D- 57
Appendix
Before detaching (or attaching) the stand, unplug the AC cord from the AC INPUT terminal.
® Do not remove the stand from the TV unless using an optional
Before attaching/detaching
wall mount bracket
to mount it.
the stand
• Before performing work make sure to turn off the TV,
• Before performing work spread cushioning over the base area to lay the TV on, This will prevent it from being
damaged,
"-1
_
-
Hex key
Unfasten
alace.
2
_ _G=
r_
r_
the four screws
used
to secure
the stand
in
Detach the stand from the TV, (Hold the stand so it
will not drop from the edge of the base area,)
., To attach the stand, per[orm the above steps in reverse order.
• This TV should be mounted on the wall only with the AN-52AG4 (SHARP} wall mount bracket. The use of other wall
mount brackets may result in an unstable installation and may cause serious injuries.
® installing the TV requires special skill that should only be performed by qualified service personnel. Customers
should net attempt to de the work themselves,
SHARP bears no responsibility for improper mounting or mounting
that results in accident or injury.
Using an optional
bracket
to mount the TV
• You can ask a qualified service professional about using an optional AN-52AG4 bracket to mount the TV to the wall.
• Carefully read the instructions that come with the bracket before beginning work.
f
Hanging
AN-52AG4
About
on the wall
wall mount
(See the bracket
instructions
Vertical mounting
setting
the TV angle
bracket.
for details.)
0/5/1C
Angular mounting
Detach the cable clamp on the rear of the TV when ushqg the optional mount bracket.
., To use this TV mounted on a wall, first remove the adhesive tape at the 4 locations on the rear of the TV, and then use the
screws supplied with the wall mount bracket to secure the bracket to the rear of the TV.
(D-
58
Appendix
Problem
Possible
,' No power
Solution
,' Check if you pressed TV POWER oil the remote control unit. (See page 16.) If the
indicator on the TV does not light up, press POWER on the TV.
,, Is the AC cord disconnected? (See page 7.)
Has the power been turned on? (See page 16.)
Unit cannot be operated.
• External influences such as lightning, static electricity, may cause improper operation.
In this case, operate the unit after first turning on the power of the TV or unplugging
the AC cord and replugging it in after 1 or 2 minutes.
,, Remote control unit does not
operate.
,, Is the FUNCTION set correctly? Set it to the TV setting position.
• Are batteries inserted with polarity (÷,
) aligned? (See page 8.)
,, Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated near the remote control sensor?
,, Picture is cut off/with sidebar
screen.
,, Is the image position correct? (See page 33.)
• Are screen mode adjustments such as picture size made correctly? (See pages 35
and 36.)
Strange color, light color, or color
misalignment
,, Power is suddenly turned off.
• Adjust the picture tone. (See pages 26 to 28.)
,, Is the room too bright? The pk_'turemay look dark in a room that is too bright.
,, Check the input signal setting. (See page 38.)
,, Is the sleep timer set? (See page 34.)
Check the power control settings. (See page 29.)
,, The unit's internal temperature has increased. Remove any objects blocking vent or
clean.
No picture
• Is connection to other components correct? (See pages 13 to 15.)
,, Is correct input signal source selected after connection? (See page 30.)
,, Is the correct input selected? (See page 30.)
Is picture adjustment correct? (See pages 26 to 28.)
,, Is "On" selected in "Audio Only"? (See page 37.)
Is a non-compatible signal being input? (See page 15.)
,, No sound
,, Is the volume too low? (See page 19.)
Is "Variable" selected in "Output Select"? (See page 37.)
,, Have you pressed MUTE on the remote control unit? (See page 19.)
,, The TV sometimes makes a
cracking sound,
,, This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to change in temperature. This does not affect the TV's
performance.
The error message
about
reception
The example of an error message
displayed on a screen
of broadcast
Error code
Possible
Solution
• Failed to receive broadcast.
E202
,, Check the antenna cable. Check that the antenna is correctly
setup.
,, No broadcast now.
E203
,, Check the broadcast time in the program guide.
Cautions
regarding
use in high and low temperature
environments
,' When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.
Storage temperature:
4°F to ÷ 140°F ( 20°C to ÷60°C)
(D" 59
Appendix
PC control of the "iV
• When a program is set, the TV carl be controlled from the PC using the RS-232C terminal. The input
signal (PC/AV) can be selected, the volume can be adjusted and various other adjustments and
settings can be made, enabling automatic programmed playing.
• Attach an RS-232C cable cross-type (commercially available) to the supplied Din/D-Sub RS-232C
for the connections.
This operation system should be used by a person who is accustomed
Communication
to using computers.
conditions
Set the R3-232C
communication
The TV's communication
settings
settings on the PC to match
are as follows:
the TV's communication
conditions.
9,600 bps
8 bits
None
1 bit
None
Communication
procedure
Send the control commands from the PC via the RS-232C connector.
The TV operates according to the received command and sends a response message to the PC.
Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending the
next command.
Command
format
Eight ASCII codes ÷ CR
I Cll
C2 I C3 IC41Pll
Command 4-digits
P2 I P3 I P 41 _
Parameter4-digits
I
Parameter4-digits:
Parameter0The9,text
x, blank,
C°mmand
4-digitS:C°mmand'
°f f°ur? characters'
Return code
Parameter
Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that 4 values are input for
the parameter.)
When the input parameter is not within an adjustable range, "ERR" returns. (Refer to "Response code format".)
Any numerical value can replace the "x" on the table.
10! ! I I
101010191
I-!3!011
I1 !0!01 I
10!0! 1 1
(D-
60
When "?" is input for some commands, the present
setting value responds.
! ! I
Appendix
Response code format
Normal response
Problem response (communication
IolKl- l
IEIRIRI- I
error or incorrect command)
Return (;ode (0DH)
Return (;ode (0DH)
Command table
• Commands not indicated here are not guaranteed to operate.
CONTROL
POWER
ON
POWER
SEWING
ITEM
COMMAND
COMMAND
SETTING
PARAMETER
_
_
SELEC•ION
A
INPUT1
SELECTION
B
INPUT
INPU•
i i
On command
reiected.
ON
The
Power
On command
acce}sted.
P......E_
It shifts
to stnndby.
Power
On
1i i i P......o,_
7
1
Oi
i
i
l iAiViD
*i
i
i
Input
:
0 I
i:
i:
AU•O
i
!
1!!!
2 !
!
VIDEO
COMPONEN•
I :!N!P!I:
3
i
!
_
i ii
SELEC•ION
A _V
N-POSITION
_
_
_iii
number
_
(Toggle}
i
i
i
1 _
_
_
STANDARD
i
i
_
i
_
2i
3 _
i
_
i
_
MOVIE
GAME
i
i
i
i
5 i
i
i
i
i
USER
DYNAMIC
i
i
i
6 _
_
_
DYNAMIC
i
i i
7i
i i
PC
8 _
D
*i*i
_
D
xvYOC
_
D
D
ViOihiM
R_P_O_S
_
D
P_O_S
CLOCK
i
i
O_L_C_K
PHASE
P i R
W i
4,,,
i
_
D
i
Volume
Only
POmode.(O
i S i E
* i
Only
PC mode.
I i U i E
0 i
* i * i
i
i
{Toggle)
i
i
i
2_
!
!
S.Stretch
i
i
i
g _
_
_
Zoom
i
i
i
4i
i
i
Stretch
An input
change
is also
Although
it can
salne
remains
as an input
as it is.
(Last
change
key)
memory))
included.
5i i i
Nor,_,a_IPOl
_
6 _
_
_
Zoom
i
i
i
7 _
_
_
Stretch
i
i
i
8i
i
i
D°t
[PC}
PC]
o_ _ _ (Tog¢_)
1!!!
a_
2i i i O_
&UDIO
SELEC•ION
TIMER
A _O _H _A
i
i
i
x
SLEEP
oiPiTiM
_
_
i i i
! ! !
_
_
l i
i i
poskion
vadable
The ranges
can
ranges
depend
be seen on the
on the View
Mode or the
position
setting
scleen.
The scleen
signal type.
poskion
vadable
The ranges
can
ranges
depend
be seen on the
on the View
Mode or the
position
setting
scleen.
One/available
when 4:3 si_nal is being input.
Onk/availabb
Onk/available
when 4:3 signal is being input.
when 4:3 signal is being input.
o,_
_
i
_
i
_
i
(Toggle)
o_ ! !
ORE
1 _
_
_
OFF
•IMEA
SO MIN.
_i i i
ORET_MEn
_OM_N.
4 _
OFFTIMER
_i i i ORET_ME_
gOM_N
_
_
120
MIN.
DiAi2ip
(01009999)
InOable,
*;*;*;*,
,
,
CHANNEL
i
_
*_*_*_
i
Air
DIGITAL
Cable
Plont
(0 999)
*_*_*_*
half
DIGITAL
(09999)
D!C!l!l
*!*!*!*
C_R_U_P
x_
C!H!D!W
x!
C i L iO i p
x
i
(08ass)
is inok_ded
(Two
_
TV display.
beffective.
P_
(Two
of DIGITAL
Cable
if it is not
effective.
1 135ch
DIGITAL
Re_ ¸ haft
D_C_I_0
in inside.
Only availabb when 720p is being input.
Tbechan,_e_nu,nbe,
ofW An input change
In AI_ 2-89ch
i_
/11s._>
i
in inside.
The scleen
signal type.
DiCiCiH *i*i*i
i i i
i i i
i
i
D_C_2_L
operation
[PqAvailableexceptwhenUXG&isbeinginput [AV]0nly a,,ailablewhen108@pisbeinginput
[AVI
Aiaisiu
i i i
i i i
i i
it is toggle
IPC1
bY D°t
SURROUND
i
now,
IAV ]
_
!
choose
TAV1
/Tog¢_)
co
(It is the
INPUT7.
[AV 1
O_ !
OH UP
OH DOWN
toggle.
Although it can choose now, it is toggle operation
IAVI
1i i i s_beBarIAVl
MiUi •iE
(DIGITA_
to INPUT1
180)
Eu_S
...... IAVl
_NALOG)
DIRECT
to 7V. (A channel
It input-switches
(040}
gi i i
CHANNEL
by the
It input-switches
(C_60}
i
i
i
* _ * _ * _
i i i
DIRECT
It input-switches
(Fixed)
*
i i i
OHANNEL
7)
COMPONENT
_
! ! !
MUTE
(l
VIDEO
0 _
V POSITION
VlEWMODE
1 _
_M _ D
iii
VOLUME
!
termin_l
_iniPiS 0i ! ! AUTO
_
PosmoN
_
Power
I ITIVID
i
!
&V MODE
_
CONTENTS
The
•OGGLE
7V
INPU•
1 _
PiOiWiR oi
i i i
INPU•
CONTROL
RisiPiW oi ! ! OFt
(Two
DIGITAL
numbers,
Part
CABLE
Part
2 digit
numbers,
CHANNEL
number_,
CABLE
plus
3 digit
NO.
g digit
CHANNEL
2-di_
plus
NO.
3-digit)
/Design_÷
plus
m_or
channel)
minor
cbennel}
3-digit)
(Designate
DIGITAL
Cable
(One
Part
numbers,
5 digit,
less thai
DIGITAL
Cable
(One
Part
numbers,
5 diqit,
more
than
10,000)
10,000/
_
_
The
channel
number
of TV _ 1
If it is not
TV display,
it will
inpt_t
switch
to TV. (same
function
a_ ORA)
!
!
The
channel
number
of TV
If it is not
TV display,
it will
inpt_t
switch
to TV. (same
function
a_ CRy)
i
i
(Toqgle)
-1
To_qle
operation
of a closed
c_ption.
• If an underbar (_)appears in the parameter column, enter a space.
• If an asterisk (*)appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
• As long as that from which the parameter (x ) in the table is a numerical value, it may write anything.
@-
61
Appendix
item
LCD panel
Number of dots
Model: LC-46D64U
Model: LC-52D64U
42" Advanced Super Vies!
& BLACK TFr LCD
(Screen size 42_/J
measured diagonally)
46" Advanced Super Vies!
& BLACK TFT LCD
(Screen size 456s/64"
measured diagonally)
52" Advanced Super View
& BLACK TFT LCD
(Screen size 52_/s2"
measured diagonally)
6,220,800 dots (1920 x 1080 )< 3 dots)
TV-standard (CCIR)
TV
Function
Model: LC-42D64U
Receiving
Channel
American TV Standard ATSC/NTSC System
VHF/UHF
VHF 2-13ch, UHF 14-69ch
CATV
1-135ch (non-scrambled
channel only)
Digital
Terrestrial
Broadcast
(SVBB) 2-69ch
Digitalcable'_
(64/256QAM)
Audio multiplex
1-135ch (non-scrambled
channel only)
BTSC System
Backlight
60,000 hours (at Backlight Standard position)
Audio out
15W x 2
Rear
Terminals
INPUT 1
AV in, COMPONENT in
INPUT 2
AV in, S-VIDEO in
INPUT 5
HDMI in with HDCP
INPUT 6
Audio in, HDMI in with HDCP
INPUT 7
15-pin mini D-sub female connector, Audio in (_ 3.5 mm jack)
ANTENNA
75 _ Unbalance, F Type × 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)
DIGFALAUDI00DTPUTOptical Digital audio output
Side
OUTPUT
Audio out
RS-232C
9-pin D-sub male connector
INPUT 3
AV in, COMPONENT in
INPUT 4
HDMI in with HDCP
USB
Software update
x 1 (PCM/Dolby Digital)
OSD language
English/French/Spanish
Power Requirement
AC 120 V, 60 Hz (FOR NORTH AMERICA)
AC 110-240 V, 50/60 Hz (FOR OTHERS)
Power Consumption
215 W (0.6 W Standby
with AC 120V)
256 W (0.6 W Standby
with AC 120V)
290 W (0.6 W Standby
with AC 120V)
TV + stand
60.6 Ibs./27.5 kg
66.1 Ibs./30.0 kg
74.9 Ibs./34.0 kg
TV only
48.5 Ibs./22.0 kg
54.0 Ibs./24.5 kg
62.8 Ibs./28.5 kg
TV + stand
89_7/s2× 277/8 x 12_s/_6
432s/64x 2959/64x 12_"_/_6 4845/64x 32s°/_ x 12_s/_6
TV only
3917/32
Weight
Dimension .2
(W× HxD)
(in inches)
Operating temperature
X
257/_6× 3s/4
4323/64x 27s_/64x 33/4
4845/_ × 30s_/_ × 33/4
+ 32°F to + 104°F (0°C to + 40°C)
Emergency alert messages via Cable are unreceivable.
The dimensional drawings are shown on the inside back cover.
As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.
mmmmmmmm_
The listed optional accessory is available for the Liquid
Crystal Television. Please purchase it at your nearest shop.
,, Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for
compatibility and check the availability.
(D-
62
Wall mount bracket
AN-52AG4
CLEARING
THE
SECRET NUMBER
If you forget the secret number, clear the secret number using the following procedure.
Press MENU to display the MENU screen, and then press _11/1_to select "Setup".
Press A/T to select "EZ Setup", "CH Setup", "Parental CTRL" or "Reset", and the Secret number
input screen displays.
I_
Setup
[ Secret
No.
_]
Press and hold both CN/X and VOL+
screen.
on the TV simultaneously until the message appears on the
INPUT
Q
C_
VOL
The secret number is _
As a precautionary
.
measure, make a note of your secret number above, cut it from this manual, and keep it in a safe place.
@-
63
Appendix
Software
composition
The software included in this product is comprised of various so[tware components whose individual copyrights
are held by SHARP or by third parties.
Software developed
by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that
were developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international
treaties, and other relevant laws. This product also makes use of freely distributed software and software
components whose copyrights are held by third parties. These include software components covered by a GNU
General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license
agreement.
Obtaining
source code
Some of the open source software licensors require the distributor to provide the source code with the executable
software components. GPL and LGPL include similar requirements. For information on obtaining the source code
for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the
following website:
http://www.sharpusa.com/gpl
We are unable to answer any questions about the source code for the open source software. The source code for
the software components whose copyrights are held by SHARP is not distributed.
Acknowledgements
The following open source software components are included in this product:
• linux kernel
• busybox
• uClibc
• zlib
• libpng
• libjpeg
(D-
64
Calling for Service
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or
customer assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
CONSUMER
LIMITED
WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand Liquid Crystal Display product (the
"Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option,
either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
)urchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has
been removed, defaced, changed, altered or tampered with. This warranty does not cover installation or signal reception problems. This
limited warranty will not apply if the Product has been or is being used in a commercial setting or application; this warranty is meant solely
for the non-commercial,
household use of the Product by consumers in their home or residence. If you intend to or already use this Product
for commercial purposes or in a commercial setting, there are warranties available to cover your use of this Product, the terms of which may
vary. Please contact 1-888-GO-SHARP
for further information.
In order to enforce your rights under this limited warranty, you should follow the steps set forth below. You must be able to provide proof of
)urchase to the servicer, which proof must include the date of purchase.
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or
implied. Specifically ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR
PURPOSE ARE SPECIFICALLY
EXCLUDED. IE UNDER APPLICABLE
STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF
PURCHASE SET FORTH BELOW. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy
available to the purchaser and only for the time periods set forth herein. No other representations
or promises made by anyone are
permitted. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all
liabilities and responsibilities
of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims,
whether based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable, or in any way
responsible, for Products which have been subject to abuse (including, but not limited to, improper voltage), accident, misuse, negligence,
lack of reasonable care, alteration, modification, tampering, misuse, improper operation or maintenance or any damages or defects in the
Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp
be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on
warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.
THIS LIMITED
Model
WARRANTY
IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT
OF COLUMBIA
AND PUERTO RICO.
Specific Section
Your Product
Warranty
Model
Number & Description:
Period for this Product:
LC-42D64U/LC-46D64U/LC-52D64U
(Be sure to have this information
Product.)
LCD Color Television
available when you need service for your
One (1) year parts and labor from the date of purchase.
Additional
Exclusions
from
Warranty Coverage (if any):
In order for the Product to be serviced, the Product must be readily available
to the servicer, free and clear of any complex or non-standard
installation,
mounting or other encumbrance
which would unreasonably interfere with
servicing the Product. The Servicer will remount the Product after service,
provided that such remounting is not into a complex or non-standard installation. Any additional labor and materials required to remove and/or reinstall a
Product above and beyond the foregoing are not covered by this warranty,
may result in additional charges and are the responsibility of the consumer.
Image Retention resulting from a fixed image being displayed for long
periods of time is not covered by this Limited Warranty (see Operation
Manual on how to prevent this).
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States. To find the
location of the nearest Sharp Authorized Servicer, please call Sharp toll free
at 1-800-BE-SHARR
What to do to Obtain
Contact your Sharp Authorized Servicer to obtain in home service for this
product. The Servicer will come to your location and if necessary remove the
unit for repair at the Servicer's facility and return the set to you once
completed. Be sure to have Proof of Purchase available.
TO OBTAIN
PRODUCT
Service:
INFORMATION
OR PURCHASE ACCESSORIES
AND EXTENDED
OR VISIT www.sharpusa.com
WARRANTIES,
CALL 1-800-BE-SHARP
(D" 65
®
LIMITED WARRANTY
Consumer E/ectronics Products
Congratulations
Sharp
Electronics
Sharp
brand
Sharp
warrants
defects
of Canada
product,
specified
when
that
should
Ltd. (hereinafter
shipped
this product
be found
in its original
is free,
in this
under
product
container
the
on your purchase!
gives
the
and sold
use and
appmicable
following
express
or distributed
maintenance,
warranty
from
period,
warranty
in Canada
to the first
by Sharp
any defects
in material
shaft,
option,
Sharp
at its
consumer
purchaser
or by an Authorized
and workmanship,
repair
for this
Sharp
Dealer:
if any
or replace
the
such
product
as
herein.
warranty
(a)
Any defects
caused
or repairs
required
use as outlined
in the owner's
manual.
(b)
Any
shall
Sharp
Damage
head
Any
not
apply
product
or Sharp's
(d)
"Sharp")
normam
within
This
(c)
called
tampered
Authorized
caused
cleaning
limited
with,
Servicing
or repairs
tapes
replacement
not
to:
modified,
of abusive
adjusted
operation,
or repaired
negligence,
by any party
accident,
other
than
improper
installation
or inappropriate
Sharp's
Authorized
Service
by Sharp,
including
but net
Sharp,
Centres
Deamers.
required
as a result
and chemical
cJeaning
of accessories,
to earphones,
as a result
glassware,
remote
controls,
of the
use with
items
not specified
or approved
limited
to
agents.
consumable
AC
or peripheral
adapters,
batteries,
items
required
temperature
through
probe,
normal
stylus,
trays,
use of the
fiJters,
product
belts,
including
but
canes
and
ribbons,
paper.
(e)
Any cosmetic
(f)
Any damage
damage
caused
to the
surface
by external
or exterior
that
or environmental
has been
conditions,
defaced
or caused
including
but not
by normal
wear
and tear.
Emited to transmission
Ene/power
line
voltage
or liquid
spillage.
(g)
Any product
received
(h)
Any products
used
(i)
Any
installation,
Shoumd this
together
setup
Sharp
with
without
for
product
proof
of
screen
of 27" or larger
This
warranty
authorized
defect
constitutes
the entire
The
manner
purchaser
with
respect
In home
damages
purchaser
end
during
express
the warranty
LIMITED
warranty
service
Over-the-Range
warranty
may
Oven.
by Sharp
any incidental,
product,
for any removal,
described
herein,
and shah
special
the
dealer,
service
extent
for the
reinstalJation,
loss
the
fell satisfaction
on any
and
of all
of aH cJaims,
or loss
insurance
based
Sharp
television
agent
of profits
Sharp
PERIODS:
Parts
Audio
Product
is
any
aft
I year
DVD
1 year
Product
Projector
I year
LCD TV
t year
Oven
1 year
Air Purifier
Portable
To obtain/he
SHARP
name
(exceptions
(lamp
incurred.
Air Conditioner
and address
ELECTRONICS
years)
1 year
of tile nearest
OF CANADA
LTI)
AuShorized
335
Sharp
Britannia
Service
Road
East,
Cen/re
or Dealer,
Mississauga,
please
Ontario
contact:
L4Z
Revision 12/16/05
of Sharp
negligence,
lW9
SHARP
._
'T
"_¢_. SERVICE
@'eOsroM _|
66
of
1 year
For more information on this Warranty, Sharp Extended Warranty
Offers, Sharp Canada Products, Accessory Sales, Dealer or Service
Locations, please call (905) 568-7140
Visit our Web site: www,sharp,ca
Q-
Correction
noted)
additional
a
loss
and responsibilities
component-4
from
or the
90 days)
(magnetron
and
resulting
I year
Camcorder
Microwave
& Labour
the
or employee
product
on contract,
or an
with
or otherwise.
WARRANTY
product
Centre
disclaims
costs
obligations
whether
Sharp
Sharp
or use of this
of the
Service
or their
permits,
damages
fulfillment
delivery
Sharp
centre
law
of time
transportation
complete
upon
Authorized
discretion
or consequential
damages
constitute
constitute
To
be obtained
to an
at Sharp's
and no other
of Sharp.
including
may
statement
Microwave
or for
to the
service
provided
or losses
product
markings.
be
on behalf
will be responsible
to the
granted
warranty
WARRANTY
warranty
of time
and CSA/cUL
period,
of this
this
relating
period
number
charges.
a copy
or transfer
serial
purposes.
on any Sharp
or workmanship
defects,
Eability
and
enlarge
of information.
to the
and
Dealer.
or indirect
in material
in the
programming
Servicing
to extend,
EabiEty for direct
and/or
fail to operate
Sharp
model,
or commercial
purchase
Authorized
size
appropriate
rental
strict
Dimensional drawings
Unit: inch (mm)
LC-42D64U
39
17/32
(1 004)
L
J
L.2121/:2
(550)
4 59/64
(125)
15 3/4 (400)
3 3/4
(95)
I 12 13/16
I
LC-46D64U
43 23/64(1101 )
[°
¢0
_o_
i
40 19/64(1023.4)
I
u_
'1
......
i:
b...
04
21
21/32 (550)
4_J
r
I
o4
4 59/64
(125)
3 3/4
(95)
15 3/4 (400)
1213/16
I
Dimensional
drawings
Unit: inch (mm)
LC-52D64U
48 45/64 (1237)
.4_,_7.o,
_ l........................................
.1
N
Lo
- ;
L
O
__J
21
¢q
15 3/4 (400)
4 57/64
(124)
21/32 (550)
3 3/4
SHAI' R
SHARP
ELECTRONICS
CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
Printed in Mexico
Imprime au Mexique
Impreso en Mexico
TINS-D194WJZZ
07P07-MX-NM