Mitsubishi 3D DLP 742 Series Operating instructions

3D DLP HOME-CINEMA TELEVISION
®
MODELS
742 Series
842 Series
BASIC OWNER’S GUIDE
This manual provides basic connection, setup, and operating instructions. For use of additional features of this television, please visit our website at www.Mitsubishi-tv.com to view or download a supplemental Owner’s Guide. Follow the Support link to the Product Documents page.
•
•
•
For questions:
-- Visit our website at www.mitsubishi-tv.com.
-- E-mail us at TVsupport@mevsa.com.
-- Call Consumer Relations at 800-332-2119 for operational or connection assistance.
For information on System Reset, please see the back cover.
To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call
800-553-7278.
®
2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol within
an equilateral triangle is intended to alert the
user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying the product.
MAINS DISCONNECTION: The mains plug is used
as the disconnect device. The mains plug shall remain
readily operable.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
En français
Cet appareil ne doit pas être exposé à des gouttes ou
à des éclaboussures et aucun objet rempli d’un liquide,
comme un vase, ne doit être placé sur l’appareil.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
TV WEIGHT: This TV is heavy. Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and disconnect all cables before moving it.
CAUTION: When selecting a stand, base, or other furniture to support the TV, please make sure it is designed with
the appropriate dimensions for stability and to support the
TV’s weight plus the weight of any additional equipment
you plan to store.
Custom cabinet installation must allow for proper
air circulation around the television.
FCC Declaration of Conformity
Product:
Models:
Responsible
Party:
Telephone:
Projection Television Receiver
WD-73742, WD-82742, WD-92742
WD-73842, WD-82842, WD-92842
Mitsubishi Electric Visual Solutions
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
1 (800) 332-2119
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by
Mitsubishi could cause harmful interference and would
void the user’s authority to operate this equipment.
Note: Features and specifications described in this
owner’s guide are subject to change without notice.
For assistance call 1(800) 332-2119
3
Contents
Cleaning Recommendations
Important Safety Instructions. .
. . . . . . . . . . . . . . .
1 Basic Setup and Operation
Package Contents. . . . . . . . . . . . . . . .
Installing the Remote Control Batteries. .
TV Overview. . . . . . . . . . . . . . . . . . . .
Before You Begin. . . . . . . . . . . . . . . . .
Remote Control. . . . . . . . . . . . . . . . . .
First-Time Power-On. . . . . . . . . . . . . . .
Setting Up and Using TV Inputs. . . . . . .
Basic TV Operation. . . . . . . . . . . . . . .
TV Menus. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . . . . . .
. . .
. . .
. . .
. . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
Appendices
Appendix A: Auto Input Sensing. . . . . . . . .
Appendix B: Lamp-Cartridge Replacement.
Appendix C: Troubleshooting. . . . . . . . . . .
18
21
24
25
. . . .
. . . . . . . . . . . . . . . . . . .
34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
MEVSA Internet Applications Policy.
. . . .
. . . .
. . . . . . . . . .
Normally, light dusting with a dry, non-scratching
duster will keep your TV clean. If cleaning beyond this
is needed, please use the following guidelines:
First, turn off the TV and unplug the power cord from
the power outlet.
Occasionally clean dust build-up from the air-intake
grilles on the back and sides of the TV. Clean using a
vacuum cleaner with a brush attachment.
Top and Sides of the TV
•
Gently wipe down your TV with a soft, non-abrasive
cloth such as cotton flannel, microfiber, or a clean
cloth diaper, lightly moistened with water. Dry with
a second dry, soft, non-abrasive cloth.
•
For oily dirt, add a few drops of mild liquid detergent, such as dishwashing detergent, to the water
used to moisten the cloth. Rinse with a second
cloth moistened only with water. Dry with a third
dry, soft, non-abrasive cloth.
13
13
14
14
28
29
31
Mitsubishi TV Software..
Warranty.
6
6
. 6
. 6
. 7
. 8
. 8
10
12
. . . . . . . .
2 TV Connections
Before You Begin. . . . . . . . . . . . . . . . . . . . .
Connection Types and Audio/Video Quality . .
Input and Output Jacks.. . . . . . . . . . . . . . . .
Connection Diagrams. . . . . . . . . . . . . . . . . .
3 TV Features
StreamTV™ Internet. . . . . . . . . . . . . .
3D Video. . . . . . . . . . . . . . . . . . . . . .
Wireless Audio Playback (842 Series). .
Sound Projector (842 Series). . . . . . . .
5
Screen
•
•
•
42
•
Follow the instructions for the top and sides, wiping
gently in an up and down motion.
Clean the entire screen evenly, not just sections of
the screen.
Do not allow liquid to drip down the screen, as
some liquid may enter the TV through the gap
between the screen and screen frame.
You may purchase Mitsubishi Screen Cleaner,
part number CLEANER-VSS, by calling
1 (800) 553-7278.
General Cleaning Precautions
•
•
TV Software
•
•
Do not attempt to update the software of this TV
with software not provided by or authorized by
Mitsubishi Electric Visual Solutions America, Inc.
Non-authorized software may damage the TV and
will not be covered by the warranty.
Automatic software updates will be downloaded
over the Internet to the TV if StreamTV is set up and
connected to the Internet.
•
•
•
DO NOT allow liquid to enter the TV through the
ventilation slots or any crevice.
DO NOT use any strong or abrasive cleaners, as
these can scratch the surfaces.
DO NOT use any cleaners containing ammonia,
bleach, alcohol, benzene, or thinners, as these can
dull the surfaces.
DO NOT spray liquids or cleaners directly on the
TV’s surfaces.
DO NOT scrub or rub the TV harshly. Wipe it
gently.
For assistance call 1(800) 332-2119
4
Mitsubishi Electric Visual Solutions
America and the Environment
As part of its ongoing environmental efforts, Mitsubishi
Electric Visual Solutions America, Inc. (MEVSA) joined
the Electronic Manufacturers Recycling Management
Company’s (MRM) national recycling initiative. Your
MEVSA TV can be recycled at no charge to the consumer through MRM’s growing infrastructure of dropoff locations around the United States.
We encourage all of our customers to recycle their
used electronics. All waste computer monitors, portable computers, digital picture frames, televisions,
portable DVD players, desktop printers, VCRs, and
video game consoles should be recycled.
For a listing of MRM recycling drop-off locations,
please visit www.MRMrecycling.com. MRM can also be
reached toll free at 1-888-769-0149
For more information about Maine’s electronic waste
law, please visit the Maine Department of Environmental Protection website at www.maine.gov/dep/rwm/
ewaste/index.htm.
For other states please check your state or local government web sites for more information about local
laws and recycling options.
Lamp Replacement
For lamp-replacement instructions, see Appendix B.
To Order a Replacement Lamp Under Warranty
Call (800) 553-7278. Please have model number, serial
number, and TV purchase date available.
To Purchase a Replacement Lamp After Warranty
Visit our website at www.mitsuparts.com or call
(800) 553-7278. Order new lamp part number
915B455012.
Children and TV Viewing
The American Academy of Pediatrics discourages
media use by children younger than two years. For more
information, visit www.aap.org.
For assistance call 1(800) 332-2119
5
Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
E XAMP LE OF ANT E NNA G R OUNDING
1) Read these instructions.
2) Keep these instructions.
ANT E NNA
LE AD IN WIR E
G R OUND C LAMP
ANT E NNA
DIS C HAR G E UNIT
(NE C AR T IC LE 810-20)
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
E LE C T R IC
S E R V IC E
E QUIP ME NT
6) Clean only with dry cloth.
G R OUND C LAMP S
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
G R OUNDING
C ONDUC T OR S
(NE C AR T IC LE 810-21)
NE C — NAT IONAL E LE C T R IC AL C ODE
P OWE R S E R V IC E G R OUNDING
E LE C T R ODE S Y S T E M
(NE C AR T 250, P AR T H)
Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS
PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES
GUIDELINES FOR THE PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS
CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
To avoid the risk of injury to the eyes and face, do not
look directly into the air vents while the television is
operating.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
To avoid the risk of fire, do not use flammable solvents
(such as benzene or paint solvents) or flammable aerosols (such as polishes, cleaners, or insecticides) near
the television while it is operating or cooling.
For assistance call 1(800) 332-2119
1
6
Basic Setup and Operation
Package Contents
TV Overview
Please take a moment to review the following list of
items to ensure that you have received everything.
Sample TV controls and
location of the STATUS
indicator. See page 33.
Remote
Control
Two AA
Batteries
AA
AA
Quick
Setup
Guide
Basic
Owner’s
Guide
Product
Registration
Card
Connection
Jacks
Installing the Remote Control
Batteries
1. Remove the remote control’s back cover by
gently pressing in the tab and lifting off the cover.
2. Load the batteries, making sure the polarities
3.
(+) and (-) are correct. For best results, insert
the negative (-) end first.
Snap the cover back in place.
1
The remote
control
requires two
AA batteries.
Lamp-Compartment
Door
TV Control Panel
Buttons on the control panel duplicate some keys on
the remote control.
To display the main menu, press INPUT and VOL+ simultaneously for about 10 seconds. Press and hold INPUT
and VOL+ for 10 seconds to clear the menu.
System Reset
If the TV fails to respond to the remote control, the
control-panel buttons, or will not power on/off, perform
System Reset. Press and hold the POWER button on the
control panel for ten seconds.
Before You Begin
1. Review the important safety, installation, and oper2
2.
ating information at the beginning of this book.
Choose a location for your TV.
• Allow at least four inches of space on all sides
of the TV to help prevent overheating. Overheating may cause premature failure of the TV.
• Avoid locations where light may reflect off the
screen.
3. Install the batteries in the remote control.
4. Plug the TV into an AC power outlet.
(120 V AC, 60 Hz)
For assistance call 1(800) 332-2119
1. Basic Setup and Operation
7
Remote Control
Aim the remote control at the TV screen. The
TV can detect control signals over the entire
screen area.
Sleep Timer. Automatically turns off
the TV after the number of minutes
you set.
Number/letter keys
Channel tuning, page 9
Pass-code entry
TOOLS key shortcuts
Powers TV on or off.
Adds a separator in digital channel
numbers. Clears some menu entries.
LAST Returns to the previous channel.
In menus, steps back one
menu.
MUTE Mutes the TV speakers.
TOOLS Displays shortcuts for the number keys.
Press to check if shortcuts are available
for the current device.
VOL Controls volume of TV speakers.
FAV
FORMAT
INTERNET
CH Changes channels; moves to another
PAGE page in a menu or list.
INPUT
Displays up to nine favorite
sources.
Changes picture shape,
page 11.
Connects to the Internet
content, page 18.
Press to select a TV input,
page 9.
ENTER Selects a channel number or menu item.
Navigation and adjustment controls
GUIDE Navigates through VUDU Apps, page
20.
INFO TV status or TV help
AUDIO
Audio settings
VIDEO
Video settings
MENU
Displays or clears the TV
main menu (page 12). Also
steps back one menu.
Clears all menus and onscreen displays.
EXIT
(Pause) Freezes a broadcast TV picture
from the ANT (antenna) input.
Playback controls for StreamTV Internet
services. May apply to compatible devices
under HDMI control. See the supplemental
Owner’s Guide at www.mitsubishi-tv.com
for setup of HDMI control.
The TOOLS Key and Menu
Press the TOOLS key to see the Tools menu. Press
number keys to activate shortcuts. Your Tools menu
may differ from the sample, depending on your setup.
• Shortcuts specific to the current device are in the
third column.
• Shortcuts may be available for a CEC-enabled
device. See the supplemental Owner’s Guide at
www.mitsubishi-tv.com.
F1–F4. Function keys for some
StreamTV Internet services.
Mitsubishi iPhone App
Visit the iTunes store for a free app
that turns your Apple iPhone, iPad,
or iTouch into a second remote
control for the TV.
Picture shortcuts
Sound shortcuts
PICTURE SOUND
TV
Device-Specific Shortcuts
Availability varies, depending on equipment features
and setup.
3 CC. Turns closed captions on/off (ANT and Y
composite inputs only)
Sample Tools menu, 842 series
For assistance call 1(800) 332-2119
8
1. Basic Setup and Operation
First-Time Power-On
1. Install batteries in the remote control. See page 6.
2. Aim the emitter (bulb) end
of the remote control at the
TV and press the POWER key
. Wait for the Welcome
screen.
Welcome Screen Energy Options
•
•
3. If you wish to change the
menu language to Español,
press then ENTER.
4. Press
to move to the
energy-mode selections.
Select Home.
5. Press
to highlight EXIT.
Press ENTER to clear the menu.
Mitsubishi recommends the Home setting,
which produces a picture suitable for home
viewing and uses less power.
The Retail setting looks best under the bright
lighting often found in commercial settings. In
this mode, the TV uses more power than when
in the Home setting.
This table compares energy choices offered in the
Welcome screen.
Home
Retail
Picture Mode
Bright
Brilliant
Lamp Energy
Standard
Bright
•
•
Use the Picture > Video menu to change the
Picture Mode.
Use the Setup > Energy menu to change
Lamp Energy.
Setting the lamp mode to Standard may extend the
life of the lamp.
Setting Up and Using TV Inputs
The ANT (Antenna) Input
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 16.
4. Highlight Ant Air if connected to an
over-the-air antenna. Highlight Ant
Cable for service over direct cable
(no cable box). Press ENTER to add a
check.
You must perform a channel scan to enable reception of digital channels. If you skip this step, the TV
can receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in your area. Note: Direct cable
service will not include scrambled or premium channels.
5. Select the scan type.
Memorizing Channels with Channel Scan
6. Highlight Scan and press ENTER.
1. Power on the TV.
2. Press MENU and open the Setup > Channel menu.
•
•
For first-time setup, highlight All channels.
To scan for channels not already in memory,
highlight Add only new channels. Press
ENTER to add a check.
Channel memorization may take up
to 15 minutes to complete.
To stop channel memorization before completion,
press CANCEL. The channels already memorized
before cancellation remain in the memory.
Start channel memorization from the Setup > Channel
menu.
3. Press
to enter the menu.
For assistance call 1(800) 332-2119
At any time after Channel Scan,
• Use the Setup > Channel > Edit menu to add or
delete individual channels from memory.
• Repeat the All channels scan if you reposition the
antenna or move the TV to a new geographic area
with a different channel line-up.
1. Basic Setup and Operation
9
Setting Up and Using TV Inputs, continued
Setting Up Inputs with Auto Input Sensing
Connection information starts on page 13. Learn more
about Auto Input Sensing on page 28.
1. Power on the TV.
2. Power on the devices to ensure detection.
3. Connect one device to the TV, making note of the
4.
TV input jack.
The TV will display the New Device Found screen if
the connection type is detectable.
Highlight the device type in the on-screen list and
press ENTER. The name you select here will appear
in the Input Selection menu.
More About the Input Selection Menu
• To assign helpful names to the icons, see the
Inputs > Name menu.
• To remove unwanted Antenna, Bluetooth®, or HDMI
device icons from the Input Selection menu, see
the Inputs > Name menu.
• To rearrange the icons, use the Inputs > Order
menu.
Detailed information on using these menus
is in the supplemental Owner’s Guide at
www.mitsubishi-tv.com.
Watching Broadcast TV
TV Connected to an Antenna or Direct Cable
Service (no cable box)
Note: Perform channel memorization to enable reception of digital channels. See page 8.
1. Press INPUT to display the Input Selection menu.
2. Highlight the antenna or cable icon and press ENTER.
Sample New Device Found screen.
5. Press EXIT to close the New Device Found screen.
6. Repeat the preceding steps for each additional
device you want to add.
Selecting an Input to Watch
1. Press INPUT.
2. Press
and
to highlight an
input icon.
Sample Input Selection menu, antenna input selected
3. To tune to a channel from the ANT input, use any of
these methods.
• Enter the channel number using the number
keys on the remote control and press ENTER .
For a two-part digital channel, such as 3-1,
—
press 3 CANCEL 1 ENTER .
• Press CH to change channels one channel at
a time.
• Press and hold CH to speed through channels.
•
•
Sample Input Selection menu, DVD input selected
3. Press ENTER to switch to the input.
Press LAST to return to the previous channel.
Use the Fav (Favorites) feature to tune to up to
nine favorite channels. See the supplemental
Owner’s Guide at www.mitsubishi-tv.com.
Note: In most cases, to see a named icon for a connected device (as in the samples), you must first
assign a name:
• When the device is first connected and the
New Device Found menu offers a choice
of names.
• By using the Inputs > Name menu to
assign or change a name at any time after
the TV has detected the connection.
For assistance call 1(800) 332-2119
10
1. Basic Setup and Operation
Basic TV Operation
Audio Controls
Controlling Sound Volume
Press VOL to adjust the sound level of
the TV speakers.
Picture Settings
To get the best picture under different viewing conditions, set the Picture Mode first before changing other
video settings.
1. Press VIDEO.
2. Press until the Picture Mode
option displays.
Changing Audio Settings (TV Speakers Only)
1. Press AUDIO.
2. Press to display the name of the
3.
adjustment you want.
Press
to change.
Using an External Sound System
To switch from the internal TV speakers to an external
sound system:
1. Press AUDIO.
2. Press to display the TV Speakers option.
3. Press to select either On (to hear sound from the
TV speakers) or Off (to hear sound from an external
sound system).
See page 17 for suggestions on connecting your sound
system to the TV.
Disconnecting an A/V Receiver
When you disconnect an A/V receiver, change the TV
Speakers setting to On to hear sound from the TV
speakers. Use the Sound > Audio > TV Speakers
menu.
HDMI Control (CEC-Enabled HDMI A/V Receiver)
The TV’s remote control may control some functions of
the A/V receiver. See the supplemental Owner’s Guide
at www.mitsubishi-tv.com.
For assistance call 1(800) 332-2119
3. Press
to make one of these selections:
Name
When to Use
Brilliant
Under very bright lighting
Game
With gaming consoles (inputs
named Game or PC only)
Bright
For most daytime viewing
Natural
For most nighttime viewing
4. Press to display the name of another adjustment.
5. Press
to make the adjustment.
6. Wait a few seconds and the display will clear.
More picture adjustments can be found in these menus:
• Picture > Video
• Picture > Picture Plus
• Picture > 3D Mode
• Picture > Perfect (842 Series only)
1. Basic Setup and Operation
11
Basic TV Operation, continued
The FORMAT Key and Picture Shape
Press the FORMAT key
to cycle through picture
shapes for the current
image. The TV will
remember the format you
last used on each input.
For more on TV formats and signal
types, see the supplemental Owner’s
Guide at www.mitsubishi-tv.com.
Important
Black bars at the edges of the
screen are common in HD pictures.
Black bars are not a defect of the
TV.
• Broadcasters add black bars to fill
the 16:9 screen area while preserving the original aspect ratio
of older material not created for
modern HD TVs.
• Your cable box, satellite receiver,
or other device may also have
controls for altering the shape
of the broadcast picture. If your
device offers output in native
format, try using it with the TV
picture formats.
Sample Uses of the FORMAT Key
You can use the FORMAT key to display the image as originally intended or
to reduce or eliminate black areas at the edges.
Press
High-definition signal with
squarish 4:3 image embedded.
The image is narrower than the
16:9 screen; unused areas at
the sides are filled with black.
Wide Expand mode stretches
the picture sideways to fill the
screen.
Press
Standard 2.35:1 anamorphic
DVD image; unused areas at
the top and bottom are filled
with black (letterbox effect).
Zoom mode. The picture fills
the screen. All four edges are
cropped in this mode.
More TV Features
See the supplemental Owner’s Guide at
www.mitsubishi-tv.com for more on these and other
topics.
• Parental controls (Lock menu). Requires first setting
a pass code.
• TV Clock (Setup > Clock menu). Set the TV Clock
if you plan to use the TV Timer or the TV’s Lock by
Time feature.
• Changing input names in the Input Selection menu
(Inputs > Name menu)
•
•
•
•
•
•
HDMI control of other A/V devices (CEC)
Using the TV with a computer
Additional Stream TV TM features
842 Series. Using the TV speakers for center
channel sound for your external surround sound
system.
842 Series. Adding external rear speakers to
complement the TV’s surround sound effect
842 Series. Using an external subwoofer
For assistance call 1(800) 332-2119
12
1. Basic Setup and Operation
TV Menus
Picture
Video Basic picture settings
Press MENU on the remote control to open
the main menu. Find detailed descriptions
of all menus in the supplemental Owner’s
Guide at www.mitsubishi-tv.com.
Picture+ Specialized picture controls
Reset Reset of sound and picture adjustments for the current input
Perfect 842 Series. Fine-tuning of color settings
Advanced Highly customized picture adjustments for each input. Mitsubishi
recommends these adjustments be
made only by a trained professional
installer.
3D Mode Setup for 3D viewing. See page 21.
Sound
Audio Basic audio settings
842 Series. Also includes subwoofer
and center-channel controls.
Global 842 Series. Settings for the AVR/REAR
OUTPUT jack.
Auto SP 842 Series. Sound Projector settings.
SoundPro See page 25.
Captions
Settings for closed captions
Setup
Language Menu language
Network Setup for the Internet connectivity. See
page 18.
Inputs
Name Name assignments for TV inputs
HDMI Setup for HDMI Control (CEC) of exterControl nal devices
Order Setup of icons in the Input Selection
menu
StreamTV Account deactivation; clears your personal data from the TV.
Demo Demonstrations of selected TV features
Update Instructions for updating TV software.
Lock
Parental Controls to limit TV use by content
ratings (composite video and antenna
inputs only)
Time Setup to lock the TV by time of day.
Set the TV clock before using this
menu.
Channel Setup to lock specific channels
(antenna input only)
Clock Set the TV clock to use the TV Timer or
to lock the TV by time.
Panel Control-panel lock
Timer Setup for the TV Timer. The Timer tells
the TV to power on automatically at a
time you set. Set the TV clock before
using the TV Timer.
Other Controls to limit TV use based on rating
systems that may come into effect
in the future (digital channels on the
antenna input only)
Channel Setup for a channel scan on the ANT
input; addition to or deletion of channels from TV memory
Energy Controls for TV energy usage
For assistance call 1(800) 332-2119
2
TV Connections
13
Before You Begin
Auto Input Sensing
Surround Sound
The TV’s Auto Input Sensing feature automatically recognizes many connections and prompts you to identify
the type of device connected. See pages 9 and 28 for
more on Auto Input Sensing.
The TV accepts PCM stereo or Dolby Digital 5.1 over
the ANT and HDMI inputs and passes the audio out on
the DIGITAL AUDIO OUTPUT jack.
Connection Types
Use the connection types available on your input
devices that will give the best video quality. For
example, choose HDMI over component video; choose
component video over composite video.
IMPORTANT
Accessories such as cables, adapters, splitters,
or combiners required for TV connections
are not supplied with the TV. These items are
available at most electronics stores.
Picture Quality
For best picture quality, route signals directly from the
source device to the TV.
Connection Types and Audio/Video Quality
VIDEO QUALITY
BEST
HDMI
DVI-to-HDMI
AUDIO QUALITY
GOOD
Component
Video
High-definition or standard-definition video
Composite
Video
Standard-definition
video only
BEST
Digital
HDMI Coaxial Audio
Dolby Digital 5.1,
PCM 2.0 (stereo)
GOOD
L/R Analog Stereo
Audio
Mini
Plug
Stereo only
HDMI Cable Categories
HDMI cables are available as Standard and High-Speed types.
more bits, also called Deep Color). High-Speed HDMI
cables are also suitable for standard HDTV signals.
• High-Speed HDMI Cables. Blu-ray players, newer DVD
players, video games, 3D content, and set-top boxes
• Standard HDMI Cables. Standard HDMI cables may be
require High-Speed HDMI cables, suitable for clock
unmarked. They are suitable for standard HDTV 720p,
frequencies up to 340 MHz or data rates of up to 10.2
1080i, and 1080p signals with 8-bit color depth. Use
gigabits per second. Use high-speed cables for 1080p
Standard HDMI cables for clock frequencies up to 74.25
HD signals carrying extended color encodings (i.e., 30 or
MHz or data rates of up to 2.23 gigabits per second.
For assistance call 1(800) 332-2119
14
2. TV Connections
Input and Output Jacks
Audio/surround OUTPUT
CENTER INPUT
SUBWOOFER OUTPUT
See the Supplemental Owner’s Guide at
www.mitsubishi-tv.com for use of these jacks.
DIGITAL
3D
GLASSES Audio
EMITTER OUTPUT
(page 21) (page 17)
ANT
Coaxial antenna
input
(page 16)
Additional jacks
offered on the
842 series.
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
1
2
USB-P
3
HDMI
(page 14, page 17)
Inputs are HDMI
HDCP compliant.
HDMI-4 offered
on the 842 series.
LAN
Y
Composite
video input
(page 16)
L
3D
GLASSES
EMITTER
ANT
R
4
DVI/PC
USB/USB-P
INPUT
• The left USB port can
Audio
accept a wireless network
input
adapter. See page 19.
(page
16)
• 842 Series. The right
USB port can power a TV
LAN
accessory such as a wire(Ethernet, port
less subwoofer.
page 18)
Y Pb Pr
Component
video input
(page 15)
L/R
Analog stereo
audio inputs
L Calibration
Microphone
(optional)
Input
(842 series,
page 25)
Connection Diagrams
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
HDMI Device
Examples: HDTV Cable Box, Satellite Receiver,
or DVD/Blu-ray Player
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
1
2
USB-P
3
4
Required: HDMI cable.
Connect an HDMI cable from the TV to the device’s
HDMI output. HDMI-connectable devices provide
video and audio through a single cable.
For assistance call 1(800) 332-2119
L
ANT
3D
GLASSES
EMITTER
R
TV jack panel
Any device with
HDMI output
Mitsubishi recommends using high-speed HDMI cables
to connect newer devices incorporating HDMI technology. See “HDMI Cable Categories” on the previous page
for more on HDMI cable types.
Note:
• This connection carries high-definition video,
3D video, and Dolby Digital 5.1 audio signals.
• This connection supports copy protection
(HDCP).
LAN
Incoming from
cable service or
satellite dish
CABLE IN or
SATELLITE IN
HDMI
cable
15
2. TV Connections
Y Pb Pr Component Video Device
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
Examples: HDTV Cable Box, Satellite Receiver,
or DVD/Blu-ray Player
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
2
1
If your source device has an HDMI output, use the connections for an HDMI device described on the previous
page instead of component video.
USB-P
3
LL
3D
GLASSES
EMITTER
R
R
DIGITAL
AUDIO
OUTPUT
TV jack panel
Required:
Component video cables
RCA-type analog audio cables
ANT
LAN
4
L
R
Component
video device
Note:
• This connection carries high-definition video
signals.
• To hear digital surround sound from an A/V
receiver, connect the digital audio output from the
device directly to your digital A/V receiver.
Audio
cables
L
R
AUDIO
Y
Component
video cables
Pb
Pr
CABLE IN or
SATELLITE IN
Incoming from
cable service or
satellite dish
VCR or DVD Recorder to an
Antenna or Wall Outlet Cable
Note:
•
•
Use composite video only
if component video or
HDMI are unavailable. A
composite video connection
cannot carry high-definition
video signals.
If your recording device has
an analog-only tuner, you
must use a digital converter
box to enable recording of
digital broadcasts.
DIGITAL
AUDIO
OUTPUT
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
1
2
USB-P
3
ANT
4
ANT
3D
GLASSES
EMITTER
DIGITAL
AUDIO
OUTPUT
Incoming
cable
R
TV panel
L
R
RF
Splitter
DVD Recorder
or VCR
L
LAN
Audio
cables
ANTENNA
IN
L
R
AUDIO OUT
or
Component
video cables
COMPONENT
VIDEO OUT
Composite
video cable
Required:
• Video cables
-- Component video cables (red/
blue/green)
or
-- Composite video cable (usually
yellow)
• RCA-type analog audio cables
• Two-way RF splitter
• Two coaxial cables
AUDIO/SURROUND
R -OUTPUT- L
COMPOSITE
VIDEO OUT
For assistance call 1(800) 332-2119
16
2. TV Connections
DVI Video Device
AUDIO/SURROUND
R -OUTPUT- L
Examples: Computer or Older A/V Device
DIGITAL
AUDIO
OUTPUT
CENTER SUB WOOFER
INPUT
OUTPUT
Note:
• This connection can carry high-definition video
signals.
• The HDMI connection supports copy protection
(HDCP).
Connect a DVI device (digital only) to one of the TV’s
HDMI input jacks.
Required:
Audio cable with stereo mini-plug
DVI-to-HDMI cable or DVI/HDMI adapter and HDMI
cable
Some devices require a connection using an analog
output first in order to view on-screen menus and to
select DVI as the output. Please review your equipment
instructions for DVI connectivity and compatibility.
HDMI
USB-P
2
1
3
L
ANT
LAN
4
3D
GLASSES
EMITTER
R
TV panel
Digital DVI
device
DVI-to-HDMI
cable
DVI OUT
AUDIO
OUT
Audio cable
Antenna or Cable TV Service
Composite Video Device
Connect the incoming cable to the TV’s ANT input.
Reception over direct cable (no box) is limited to nonscrambled analog and digital channels.
VCR or other device with composite video
output
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
1
2
USB-P
3
4
LAN
L
ANT
3D
GLASSES
EMITTER
R
ANT
Note: This connection does not support high-definition video signals.
Required:
Composite video cable (usually yellow)
RCA-type analog audio cables
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
TV panel
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
1
UHF/VHF
antenna
or
Direct cable (no cable box)
Cable
TV
service
or
2
For assistance call 1(800) 332-2119
4
LL
ANT
LAN
DIGITAL
AUDIO
OUTPUT
TV jack panel
L
R
VCR or other device
with composite
video output
L
Older IN OUT
cable
Not recommended. Other
box
connection types provide better
quality audio and video.
USB-P
3
Audio
cables
R
AUDIO OUT
COMPOSITE
VIDEO OUT
Composite
video cable
3D
GLASSES
EMITTER
R
R
17
2. TV Connections
A/V Receiver
A/V Receiver with HDMI Output
Most setups require either a digital audio cable or
analog stereo audio cables. To send audio from TV
channels received on the ANT input or devices connected directly to the TV, you must use one of the connections shown below.
The TV makes all incoming audio available as an output:
• Analog incoming audio is available as output in
digital stereo format on the DIGITAL AUDIO OUTPUT
jack. 842 Series. Analog incoming audio is also
available as analog stereo on the AUDIO/Surround OUTPUT jacks.
• Digital incoming audio is available as digital audio
on the DIGITAL AUDIO OUTPUT jack. 842 Series.
Digital incoming audio is also available as analog
output on the AUDIO/Surround OUTPUT jacks.
Required: One HDMI cable
This option allows you to view and hear content from
devices connected to an A/V receiver. The A/V receiver
can send audio and video to the TV over a single HDMI
cable.
You can add an optional audio connection from the
TV’s audio output. The optional audio connection
allows you to hear, through the A/V receiver, devices
connected to the TV only, e.g., an antenna on the ANT
input.
See page 10 for tips on using an external sound system.
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
See page 10 for tips on using an external sound system.
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
2
1
USB-P
3
4
L
LAN
3D
GLASSES
EMITTER
ANT
R
AUDIO/SURROUND
R -OUTPUT- L
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
DIGITAL
AUDIO
OUTPUT
CENTER SUB WOOFER
INPUT
OUTPUT
AUDIO/SURROUND
R -OUTPUT- L
HDMI
1
2
USB-P
3
LAN
4
TV
L
ANT
3D
GLASSES
EMITTER
R
DIGITAL
AUDIO
OUTPUT
Optional
analog or
digital audio
connection
TV
842 Series
only
HDMI
cable
or
HDMI OUT
OPTICAL
INPUT
COAXIAL
INPUT
A/V receiver back panel
If your A/V receiver converts
all video signals for output
on HDMI, you can use any
connection types from
external devices; content
can be HD or SD video.
R
L
DIGITAL
AUDIO IN
ANALOG AUDIO IN
DVD
player
VCR
Cable
box
Note: On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from the
TV as a digital signal. To hear these copy-protected signals through the A/V receiver, use the
connection for an analog A/V receiver.
• Check the A/V receiver’s Owner’s Guide for
information on use of the digital input and
switching between digital sound and analog
stereo sound from the TV.
For assistance call 1(800) 332-2119
3
18
TV Features
StreamTV™ Internet
2. Open the Setup > Network menu to review set-
About StreamTV
Internet services let you access many popular on-line
applications providing both free and paid content.
tings.
This section describes using VUDU Movies and VUDU
Apps. For additional Stream TV features, see the supplemental Owner’s Guide at www.mitsubishi-tv.com.
Required for StreamTV Internet media:
• Broadband Internet service (at least 2 Mbps for SD,
4 Mbps for HD, and 8 Mbps for 1080p HDX)
• Category-5 Ethernet cable or a wireless router
transmitting to an AzureWave AW-NU231 USB wireless adapter.
• Computer access to the websites of content providers when initial account activation is required for
service.
• A credit card to cover the cost of paid content.
Home Network Setup
Before using StreamTV Internet media, you must
connect the TV to the Internet using either an Ethernet
cable or a wireless connection as described here.
Note: Make sure the TV is on any input other than
Bluetooth®. Press the INPUT key to change.
Wired Ethernet Connection
DHCP (automatic)
1. Connect the TV to your network router with a Category-5 Ethernet cable (not supplied).
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
1
2
USB-P
3
LAN
4
ANT
LAN
3D
GLASSES
EMITTER
L
R
TV Panel
Router or modem
Incoming providing high-speed
internet
internet service
cable
Ethernet
cable
For assistance call 1(800) 332-2119
Setup > Network, DHCP connection
3. Press EXIT to clear the menu.
4. Press the INTERNET key on the remote control to
begin using this feature.
Manual
Note: Manual setup is available only for a wired connection.
1. Connect the TV to your network router with a Category-5 Ethernet cable (not supplied).
2. In the Setup > Network menu, highlight Manual
and press ENTER .
3. Press to move to the Connection Data area.
4. Input the connection data.
5. After entering connection data, press ENTER to
connect.
6. Change any of the following if needed:
• Default Gateway
• DNS
• Subnet Mask
3. TV Features
19
StreamTV™ Internet, continued
Wireless Connection
The TV requires an AzureWave AW-NU231 USB wireless
adapter to communicate with your IEEE 802.11n-compliant wireless network router. The adapter is available from
your Mitsubishi dealer or go to www.mitsubishi-tv.com
and follow the Accessories link.
1. Disconnect the Ethernet cable if present.
2. Connect the wireless adapter to the TV’s USB port.
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
1
2
USB-P
3
LAN
Setup > Network menu after connecting. The active
network is checked and connection data displays.
5. If connecting to a secure network, enter the
network key or password when prompted. Special
remote control keys you may need:
L
ANT
4
3D
GLASSES
EMITTER
R
Key
Use for
1
Incoming
internet cable
CANCEL
Wireless
adapter
•
•
IEEE 802.11n-compliant wireless
network router providing
high-speed internet service
Connect the USB adapter to the USB port on the back
of the TV. Use the left USB port.
Digit 1 and special characters
! @ # $ % ^ * _ - + = . space ?
Clears the password box of an old
entry from a prior session.
Deletes one character during password entry.
Toggle between upper and lower case
6. Press ENTER to connect.
3. Open the Setup > Network menu. After a few
moments, detected networks will appear listed on
the screen in order of signal strength.
Using StreamTV Internet Media
1. After establishing the Internet connectivity as
2.
3.
described in “Home Network Setup,” page 18,
switch the TV to any input other than Bluetooth®.
Press the INTERNET key to display services.
Press ENTER to launch an application.
Troubleshooting
Setup > Network menu, wireless connection
4. Highlight the desired network and press ENTER to
connect. A check will appear next to the connected
network. Press CH/PAGE to see more networks if the
list fills more than one screen.
If You Are Unable to Connect to the Internet
• Check all power and data connections.
• If you can reach the Internet with a computer or
other device on the same Internet service used by
the TV, consult the router or modem owner’s guide
for reset instructions.
•
If you cannot reach the Internet, contact your
service provider. You may be asked for network
information such as the TV’s IP address. Go to the
Setup > Network menu to see connection data.
For Further Assistance
If you are having trouble connecting your TV or accessing the Internet applications, contact Mitsubishi Customer Care at 1 (800) 332-2119.
For assistance call 1(800) 332-2119
20
3. TV Features
StreamTV™ Internet, continued
VUDU
5. When you are ready to rent or buy a movie, you
Internet services provided by VUDU™ Apps let you
access many popular on-line applications. In addition
to free content, VUDU’s movie service lets you buy and
rent movies through the TV. Visit www.VUDU.com
to learn more about available movie titles, prices, and
services offered.
Once your account is activated, you can rent and buy
movies using only the TV and the TV’s remote control.
will be prompted to activate your VUDU account.
Follow the on-screen instructions and use a computer to go to www.VUDU.com/activation. A
credit card is required for activation.
Note: From time to time you may notice changes to
the Internet interface as new features are added.
If you are having difficulty with your VUDU
account, contact VUDU Customer Care at
www.VUDU.com/support.
Getting Started with VUDU Movies
1. After establishing the Internet connectivity as
2.
3.
4.
Other VUDU Support
described in “Home Network Setup,” page 18,
switch the TV to any input other than Bluetooth®.
Press the INTERNET key to display the menu for
selecting VUDU Apps or VUDU Movies.
Press
to select VUDU Apps for the content or
VUDU Movies for the movie service, and then press
the ENTER key.
Browse the VUDU movie catalog and offerings.
Reset your VUDU
account password
Using a computer, go to
www.VUDU.com (reset
requires access to e-mail).
Reset your parental
controls pass code
Call VUDU Customer Care at
1-888-554-VUDU (8838).
For a list of routers and switches recommended for
use with VUDU services, see the Support > FAQ
section at VUDU.com.
Using VUDU Apps and VUDU Movies
Navigate VUDU’s menus with the keys on the TV’s
remote control. Browse the movie catalog, watch
movie previews, set parental controls, and rent or buy
movies.
• Key functions vary according to context
and may change with newer versions of
VUDU.
• Some VUDU screens include instructions
identifying available key functions.
CANCEL. Usually acts like the backspace key
during text entry.
Directional navigation
In VUDU Apps, press
more applications.
LAST. Goes to a previous screen.
LAST
TOOLS
INTERNET
ENTER. Confirms a selection.
•
•
TOOLS. Use the Tools menu to perform A/V reset
while in VUDU movies or some VUDU Apps.
CH/PAGE. Jumps to the previous or next page of
menu items.
INTERNET. Displays the StreamTV™ menu.
Switch the TV to any input other than Bluetooth®
before connecting to the Internet.
to display
GUIDE. In some contexts, returns to the
VUDU home menu.
INFO. In VUDU’s movie service, displays
more options for the current selection if
available.
F1. Displays a VUDU help menu if available.
For assistance call 1(800) 332-2119
EXIT. Closes the current screen and goes to a
home screen.
Playback keys.
F2. Displays the VUDU system menu if
available.
21
3. TV Features
3D Video
Emitters for controlling 3D glasses are as follows.
742 Series: Internal IR emitter, Internal DLP Link
Signal, or Optional External emitter.
842 Series: Internal Bluetooth® RF, Internal DLP Link
Signal, or Optional External emitter.
• Active-shutter 3D glasses compatible with any one
of the following:
-- The TV’s internal emitters
-- DLP link
-- A matching external synchronization emitter
connected to the TV’s back panel
For 742 Series: Glasses compatible with the TV’s IR
internal (742 Series) emitters are:
-- XPAND model 3DG-X103 IR glasses made for
Mitsubishi 3D TVs
-- XPAND model X103 Universal IR glasses
For 842 Series: Glasses compatible with the TV’s
internal Bluetooth® RF emitters are:
-- Refer to the company website for the recommended 3D glasses.
For all models:
-- All glasses made to use the DLP link system
•
For more information, visit the 3D TV page at
www.mitsubishi-tv.com.
A compatible 3D source device connected to the
TV via HDMI or StreamTV Internet and outputting a
3D signal in one of these formats:
-- Frame Packing 1080p@24 Hz or 720p@60 Hz
Off
• Turns off 3D images; displays 3D content
as 2D (you may see two images).
• Restores normal TV adjustment options
when viewing an ordinary 2D signal.
1
Automatic
HDMI
• Switches
the TV to 3D mode and selects the
2
correct
3D format
3 when the TV detects a 3D
signal from an HDMI 1.4a-compliant device
or a 3D movie from VUDU Movies.
• Automatically switches the TV out of 3D
mode when receiving a normal 2D signal.
Using the TV’s Internal Emitters
Typical effective range
of the emitters in the
vertical and horizontal
planes.
Ranges can be affected
by room lighting and
glasses brand and
model.
16 ft.
20°
25 ft.
20°
16 ft.
35°
25 ft.
35°
16 ft.
--
Side-by-Side(Half) 1080p@24/30/60 Hz,
1080i@60 Hz, or 720p@60 Hz
Top-and-Bottom 1080p@24/30/60 Hz or
720p@60 Hz
Checkerboard 1080p@60 Hz (lower resolutions
may be supported but will not fill the screen)
---
Initial Setup
1. If your 3D glasses came with a synchronization emitter,
connect the unit to the 3D GLASSES
EMITTER jack.
DIGITAL
Place the emitter at the front AUDIO
of the TV where there is a
clear path to the glasses. OUTPUT
Note: No emitter is required if using the TV’s internal
emitters or DLP Link.
L
3D
GLASSES
EMITTER
ANT
DIGITAL
AUDIO
OUTPUT
R
L
ANT
HDMI
1
2
3
3D
GLASSES
EMITTER
R
Connecting an external emitter
2. Power on the TV and the source device.
3. Connect the source device to the TV’s HDMI input.
4. When the New Device Found screen displays,
name the input.
5. Press EXIT to close the New Device Found screen.
Use the Picture > 3D Mode
menu to enable 3D video.
Choice of Source Formats
If your device is not HDMI 1.4a
compliant, you must choose the
correct setting from this list.
Depth
Adjusts the simulated 3D effect
applied to a 2D image. Available
only when Source Format is set
to 2D+ Depth.
For assistance call 1(800) 332-2119
22
3. TV Features
3D Video, continued
Using RF (Bluetooth®) 3D Glasses with the
Internal RF Emitter (842 Series)
1. Before you view 3D content, pair the RF
(Bluetooth®) 3D glasses with the internal RF
emitter. The pairing starts when you press the
POWER button on the glasses for more than 2
seconds within 1.5 feet from the TV.
Operating range
Recommended distance
for pairing
1.5 ft.
2. A message is displayed saying that the paring has
3.
4.
5.
been completed.
Connect the source device to the HDMI input on
the TV.
When the New Device Found screen is displayed,
name the input.
Press EXIT to close the New Device Found screen.
Note:
• Only the Bluetooth® 3D glasses authorized by
Mitsubishi can be used.
• You cannot use Bluetooth® 3D glasses and
A2DP music players at the same time.
For assistance call 1(800) 332-2119
3. TV Features
23
3D Video, continued
Watching 3D Video
Other Options in the 3D Menu
Active 3D glasses are required. All glasses in use
at the same time must use the same control type.
Halogen lights, fluorescent lights, or direct sunlight can
interfere with operation of the glasses.
Glasses Control The Off settings disable output
Off Settings from the selected emitter.
• Use Off to prevent IR interference when using an external
emitter.
• Use Off for DLP Link if you are
not using DLP Link glasses.
1. Switch the TV to the 3D video device. Press INPUT
then highlight the icon for the 3D video device. Press
ENTER.
2D+ Depth When selected, generates a simulated 3D image from an ordinary
2D image. Adjust the effect using
the Depth setting. Requires use of
active-shutter 3D glasses.
Note: Before watching 3D images from an Internet
source, it is important to establish the Internet
connection first before enabling 3D mode.
2. Press MENU and select the Picture > 3D Mode menu.
3. For Source Format, select Automatic and press
ENTER. Press EXIT to close the menu.
• If the image looks correct, the device is HDMI
1.4a compliant; always keep the setting at
Automatic for this device.
• For non-compliant 3D sources, open the
Picture > 3D Mode menu and select a source
format based on how the picture looks:
Side by Side
Two images, screen
split vertically
Top/Bottom
Two images, screen
split horizontally
Notes on Using 3D Video Settings
3D signals and 3D settings affect some TV functions.
Switch to a non-3D source to regain full TV operation.
If Source Format is set to Automatic or one of the
named 3D formats OR Source Format is set to Off and
the 3D video source is HDMI 1.4a compliant (picture may
still appear as 2D), the following limitations apply:
• Picture adjustments are limited. To make picture
adjustments while watching normal 2D images from
the device, temporarily set Source Format to Off to
make the full range of adjustments accessible.
• While receiving a 3D signal,
-- The FORMAT key is disabled.
-- The INTERNET key is disabled.
3D Safety Requirements
•
Checkerboard
Blurry double image
(always required for
checkerboard signals)
4. Press EXIT to close the menu.
5. If the image does not appear correct (e.g., objects
appear to be moving in instead of out), open the
Picture > 3D Mode menu. Highlight the Reverse
setting for the current control type and press ENTER
to add a check.
6. When finished watching 3D video:
•
•
If your 3D video device is HDMI 1.4a compliant,
keep the setting on Automatic.
If you manually selected a source format in the
Picture > 3D menu, open the menu again and
select Automatic or Off.
3D Glasses are NOT designed as sunglasses or
safety glasses and do not provide protection. 3D
glasses should be worn only when viewing 3D material.
• Do not wear the wireless glasses in any situations
that require unimpaired visual perception.
• Children under the age of 5 should not view 3D
programming.
Under normal conditions, 3D viewing is safe for your movies
or games. Some people may experience discomfort,
however. To minimize the potential for experiencing visual
problems or any adverse symptoms:
• Read and follow any and all safety warnings that accompany your 3D glasses or 3D source devices.
• Maintain a distance of no less than 2 to 2.5 times the
screen height measurement away from the display.
Viewing from too short a distance can strain your eyes.
• Take regular breaks, at least 5 minutes after every hour of
3D viewing.
If you experience any of the following symptoms, discontinue
3D viewing until the symptoms go away:
• nausea, dizziness, or queasiness,
For assistance call 1(800) 332-2119
24
3. TV Features
3D Video, continued
• headache, or eyestrain,
• blurry vision,
• double vision that lasts longer than a few seconds,
Do not engage in any potentially hazardous activity (for
example, driving a vehicle) until your symptoms have completely gone away. If symptoms persist, discontinue use and
do not resume 3D viewing without discussing your symptoms
with a physician.
Do not use the glasses where loss of balance or limiting your
field of vision may be dangerous to you.
Do not use near staircases, ledges or balconies. You may
risk falling during or after use.
Epilepsy
WARNING! IF YOU OR ANY MEMBER OF YOUR FAMILY
HAS A HISTORY OF EPILEPSY, CONSULT A PHYSICIAN
BEFORE USING 3D VIDEO OR GAME PRODUCTS.
A small percentage of the population may experience epileptic seizures when viewing certain types of TV images or video
games that contain flashing patterns of light.
The following people should consult a physician before
viewing 3D Games or Video:
• Anyone with a history of epilepsy, or who has a family
member with a history of epilepsy
• Anyone who has ever experienced epileptic seizures or
sensory disturbances triggered by flashing light effects.
WARNING! SOME LIGHT PATTERNS MAY INDUCE
SEIZURES IN PERSONS WITH NO PRIOR HISTORY OF
EPILEPSY. DISCONTINUE 3D VIEWING IF YOU EXPERIENCE ANY OF THE FOLLOWING SYMPTOMS:
• Involuntary movements, eye or muscle twitching
• Muscle cramps
• Nausea, dizziness, or queasiness
• Convulsions
• Disorientation, confusion, or loss of awareness of your
surroundings
Notice Concerning Format Compatibility
The Mitsubishi TVs will support the mandatory HDMI
1.4a 3D signals intended for the United States. Specifically, the TVs will support the 3D signals known as
Frame Packing 1080p@24 Hz and 720p@60 Hz (primarily from Blu-ray players and gaming consoles), Sideby-Side(Half) 1080p@24/30/60 Hz, 1080i@60 Hz, and
720p@60 Hz, Top-and-Bottom 1080p@24/30/60 Hz
and 720p@60 Hz, and Checkerboard 1080p@60 Hz.
However, there may be some 3D sources that are not
compatible with the TVs. In all cases: (1) 3D sources
must connect to the TVs using the HDMI inputs or via
StreamTV™ Internet Media; and (2) Active Shutter 3D
glasses that match the TV’s internal synchronization
emitter, or Active Shutter 3D glasses with their own
external matching synchronization emitter connected to
the rear of the TV or DLP Link Active Shutter 3D glasses
are required in order to view 3D content.
For assistance call 1(800) 332-2119
Wireless Audio Playback (842 Series)
The TV’s built-in speaker array can play audio from a
handheld device using Bluetooth® A2DP (stereo audio)
wireless technology.
Pairing the TV with an Audio Playback
Device
1. Turn on the wireless device you wish to use for
playback.
Press INPUT to display the Input Selection menu.
2.
3. Highlight the Bluetooth icon and press ENTER .
4. Pair your device with the TV and then connect. Some
5.
devices pair and connect automatically, while others
require you to enter the TV pass code displayed.
Use keys on the TV’s remote control to control playback. Not all keys work for all devices.
Resetting Bluetooth Pairing or Connection
Perform this reset if the audio device does not connect
properly to the TV.
1. If the audio device has been previously paired with
the TV, delete the TV from the device’s paired list.
2. Go to the TV’s Inputs > Name menu and highlight
3.
4.
5.
the Bluetooth icon. Press ENTER to select Off.
Press EXIT.
Go to the Inputs > Name menu and highlight the
Bluetooth icon. Press ENTER to select On.
Press EXIT .
Tips for Wireless Playback
•
•
•
•
•
Selecting the Bluetooth icon at a later time will
connect the TV again to the paired device.
If the paired device is not available, the TV will
accept pairing from a different device.
Once connection is lost, the TV will power off after
five minutes without receiving a signal.
To clear a paired device, turn off the Bluetooth icon
(Inputs > Name menu) or pair the TV with a different device.
To remove the Bluetooth icon from the Input
Selection menu, turn off the icon in the Inputs >
Name menu.
3. TV Features
25
Sound Projector (842 Series)
Sound Projector Technology
Connecting the TV
The TV’s built-in speaker array can be adjusted to
reflect sound off the room walls to create a surround
sound effect. Setup can be performed either manually
or automatically.
• To create the surround sound effect, the room walls
must reflect sound and not be covered with soundabsorbent material.
• Repeat the setup procedure if you reconfigure the
room’s walls or furnishings.
To hear digital surround sound, the TV must be connected to a digital surround sound source. The TV can
receive digital surround sound from:
• Any HDMI jack
• The ANT input (from some digital broadcasts)
Before You Begin
•
Microphone Placement for Auto Setup
•
Positioning the TV
•
Other stereo connections will provide Dolby Pro Logic
surround sound.
•
Center the seating area in front of the TV and at
least six feet away from it.
Arrangements that give good results:
Make sure there are no large obstacles between
the TV and microphone.
Place the microphone
-- On a flat, level surface at least six feet away
from the front of the TV.
-- On a tripod or on the backrest of your seating.
-- At the same height yours ears would be when
watching TV. The height must be within 3
vertical feet of the height of the TV’s speaker
array.
-- Centered in front of the TV, not off to the side.
TV
•
Height of TV
speaker array
If the room is an odd shape, locate the TV to take
best advantage of wall reflections.
6 ft. minimum
or
Microphone
Set the microphone
on a level surface at
ear height at least
six feet from the TV.
Use a seat backrest
or tripod so as to
pick up sound from
all directions.
Maximum height above speakers
6 ft. minimum
•
3 ft.
Avoid locations that may distort sound reflections.
Height of TV
speakers
3 ft.
Be sure the
height of the
microphone is
within three feet
of the speaker
height.
3 ft.
Minimum height below speakers
Microphone
Center the microphone in front of
the TV.
To purchase an optional calibration microphone, visit
our website at www.mitsuparts.com or call
(800) 553-7278. Part Number 485P028010.
For assistance call 1(800) 332-2119
26
3. TV Features
Sound Projector, continued
Auto Setup
Basic Manual Setup
Auto setup uses a calibration microphone to optimize
Sound Projector performance for most room conditions.
Initial Preparation
1. Position and connect the TV as described under
2.
3.
“Before You Begin” on the previous page.
Power on the TV and external subwoofer, if any.
Plug the microphone cable into the TV’s INPUT 1 left
(white) audio jack.
AUDIO/SURROUND
R -OUTPUT- L
DIGITAL
AUDIO
OUTPUT
CENTER SUB WOOFER
INPUT
OUTPUT
HDMI
1
2
USB-P
3
LL
ANT
LAN
4
3D
GLASSES
EMITTER
DIGITAL
AUDIO
OUTPUT
Note: If you have already performed Auto setup, do
not make manual adjustments. Doing so will
erase all settings created during Auto setup.
1. Press MENU and go to Sound > SoundPro.
2. Enter the room dimensions and layout information
requested in the screen. To change measurements, press
or enter numbers on the remote
control’s keypad.
R
R
TV jack panel
L
R
Connect microphone to the
left (white) audio input jack.
4. Place the microphone as described in the guidelines on the previous page.
Start Auto Setup
5. Press MENU and go to Sound > AutoSP.
3. Press EXIT to exit and save settings.
4. Play some sample audio to check sound quality.
If further adjustment is needed, use the Custom
menu as described next.
Custom Menu
Use the Custom menu after defining the room layout.
6. Highlight START and press ENTER .
7. Quietly exit the room right away. The calibration
8.
9.
sequence will start in a few seconds and may be
loud. It is important to leave the room as your presence will interfere with the calibration process.
Wait for completion of setup before returning
to the room.
Play some sample audio material to check the
sound quality.
Note: Do not perform manual adjustments after running Auto setup, as this will erase all settings
defined during Auto setup.
10.Store the microphone out of direct sunlight and
away from heat.
For assistance call 1(800) 332-2119
For a room with large areas of curtains that might affect
sound reflection, do the following:
a. Open the curtains fully to improve sound reflection.
b. Set angles by performing the procedure in
“Adjusting Beam Angles.”
c. Close the curtains.
d. Set levels by performing the procedure in
“Adjusting Levels.”
3. TV Features
27
Sound Projector, continued
1. From the Sound > SoundPro menu go to the
CUSTOM menu.
Making Adjustments in the Custom Menu
• Press
to select an audio beam; colors of the
adjusters correspond to audio beams in the onscreen diagram.
• Press
to redirect the audio beam or change
the sound level.
2. Position yourself in your usual viewing location.
Remain in this position, looking at the TV, while
making the following adjustments.
3. Adjusting Beam Angles
a. Adjust Center Beam Angle until sound is
about equal in both ears.
b. Adjust Left Beam Angle to maximize sound
heard from the front left side.
c. Adjust Right Beam Angle to maximize sound
heard from the front right side.
d. Adjust Left Surround Beam Angle to where
the sound seems to come from the left rear
side. If this cannot be achieved, make the
setting the same as that for Left Beam Angle.
e. Adjust Right Surround Beam Angle to where
the sound seems to come from the right rear
side. If this cannot be achieved, make the
setting the same as that for Right Beam Angle.
Controls in the SoundPro
> Custom menu adjust the
direction and focus of the TV’s sound output.
At extreme beam angles, adjustment may be limited
and the image on screen may not accurately represent
the sound beams.
4. Adjusting Levels
a. Adjust Center Level to the mid level.
b. Adjust the following levels one at a time so that
each one sounds about the same as the center
level:
Left Level
Right Level
Left Surround Level
Right Surround Level
c. Check all sound levels by quickly switching
between them using
.
d. Readjust individual levels in small increments
and recheck as above until all sound levels
seem about the same.
5. Adjusting an External Subwoofer
Note: Set Sound > Global > Subwoofer to On to
make this adjustment available.
a. Play sample video or music containing lowfrequency bass sound.
to display the Subb. Press AUDIO . Use
woofer option.
c. Press
to adjust the subwoofer volume.
Adjust the volume level of individual audio beams
using sliders in the SoundPro > Custom menu.
Resetting Angle and Level Values in the Custom
Menu
Follow these steps to return settings to the default
values.
1. Press EXIT to clear all menus.
2. Press MENU . Go to the Sound > SoundPro
menu and press ENTER .
Change any setting (e.g., TV Location).
Press EXIT to clear all menus.
3.
4.
5. Press MENU . Go to the Sound > SoundPro
6.
7.
menu and press ENTER .
Enter the correct values for the room layout.
Return to the CUSTOM menu to adjust angles
and levels.
For assistance call 1(800) 332-2119
28
Appendices
Appendix A: Auto Input Sensing
About Auto Input Sensing
This TV’s Easy Connect™ Auto Input Sensing feature
detects the following connections automatically:
• Analog video jacks
• HDMI inputs (when powered on)
Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connected device and automatically switch to it.
b. Prompt you to identify the device type.
c. Repeat these steps for other newly detected
devices.
When You First Connect a Device
•
•
•
Most Device Types. Select the device type from
the on-screen list. The device type you select here
will appear as an icon in the Input Selection menu.
A/V Receiver. For an HDMI-equipped A/V
receiver, select AVR from the list of device types if
the A/V receiver is not recognized automatically.
HDMI CEC Devices Compatible with the
TV’s HDMI Control Feature. Compatible
CEC-enabled HDMI devices are often recognized
automatically by the TV. HDMI Control may allow
you to control some functions of a CEC-enabled
device. See the supplemental Owner’s Guide at
www.mitsubishi-tv.com.
Tips on Auto Sensing
•
•
•
•
•
Reactivating Auto Input Sensing for an HDMI Input
After you disconnect an HDMI device, Auto Input
Sensing is temporarily disabled and the disconnected
device still appears in the Input Selection menu.
Perform these steps:
1. Power off the device.
2. Disconnect the HDMI cable.
3. Press MENU on the TV remote control to enter the
TV main menu.
4. Go to Inputs > Name.
5. Highlight the HDMI input name and press ENTER to
6.
New Device Found screen for a device with HDMI
control enabled. Select On if you want to enable the
TV’s HDMI control of the device. In some cases, as
in the example, you will also be prompted to select a
device name.
Note:When HDMI Control is set to Off, the TV
may still respond to CEC commands sent by
another device. To prevent this, turn off HDMI
Control in the device using the device’s own
menus.
For assistance call 1(800) 332-2119
Choose a different name for each input.
The antenna input (ANT) and Bluetooth® are
never auto-detected. You can remove the unused
icons from the Input Selection menu in the
Inputs > Name menu.
Change the device type displayed in the Input
Selection menu by using the Inputs > Name
menu.
Some HDMI devices can automatically tell the TV
what name to use in the Input Selection menu
and you will be unable to change the name.
The TV is unable to detect a new connection if
the current input is Bluetooth® or the Internet.
Switch to a different input before connecting.
select Delete.
Press EXIT to clear the menus.
Inputs > Name menu with Delete selected for
HDMI-3.
7. Connect the new device and the New Device
Found screen will display.
Appendices
29
Appendix B: Lamp-Cartridge Replacement
CAUTION: If the television is on, press POWER to turn it off. Unplug the television and
allow it to cool for at least one hour before attempting to replace the lamp cartridge.
Lamp
CAUTION
The light source for this television is a
lamp, which is part of a lamp cartridge
assembly. The life of the lamp can
BURN DANGER! HOT SURFACES INSIDE!
vary, based on the lamp itself, the air
Touch lamp cartridge handle only. Do not touch lamp or lamp cartemperature around the TV while it is
tridge housing. Keep lamp cartridge horizontal during removal. Do
operating, the selected lamp mode, and
not tilt as glass may come out and cause injury. Replace lamp caryour viewing patterns. Warmer air or
tridge only with the same part number 915B455012.
poor ventilation shorten the lamp life, as
does setting Lamp Energy to Bright
and turning the television on and off
frequently.
WARNING
Mitsubishi warrants the lamp for one (1) year from the date of original
THE ACCESS PANEL IS
TV purchase at retail.
PROVIDED WITH AN INTERLOCK
TO REDUCE THE RISK OF
The lamp cartridge assembly is designed to be replaced by the TV
EXCESSIVE ULTRAVIOLET
owner. The cost of labor for a service technician to replace the lamp
RADIATION. DO NOT DEFEAT
is not covered by the warranty.
ITS PURPOSE OR ATTEMPT TO
SERVICE WITHOUT REMOVING
Ordering a New Lamp
PANEL COMPLETELY.
To Receive a Replacement Lamp Cartridge Assembly Under Warranty
• Visit our website at www.mitsuparts.com.
• Call (800) 553-7278. Please have model number, serial number,
and TV purchase date available.
To Purchase a Replacement Lamp Cartridge Assembly After Warranty
Visit our website at www.mitsuparts.com or call (800) 553-7278. Order the following:
Lamp Part Number 915B455012
Lamp-Substitution Alert
MEVSA recommends that you use only genuine Replacement Lamp Assemblies purchased directly from Mitsubishi or a
Mitsubishi Authorized Dealer or Mitsubishi Authorized Service Center. MEVSA advises that replacement lamps obtained
separately from the Lamp Cartridge and/or Lamp Assemblies obtained from unauthorized sellers may be incorrect for
your television, may not fit or perform properly and may even damage your television. MEVSA can not be responsible
for the performance, reliability or safety of any replacement lamps that are obtained from unauthorized sources.
WARNING
•
•
•
•
•
•
Do not remove the lamp cartridge immediately after turning off the television. You may get burned because the
lamp is very hot. Allow the television to cool for at least one hour before replacing the lamp cartridge.
Do not remove the lamp cartridge except when replacing it. Careless treatment can result in injury or fire.
Do not touch the lamp glass element. It may be very hot and break, causing injuries or burns.
Be sure not to insert any metal or flammable object into the lamp cartridge opening, as it may cause fire or electrical shock. If a foreign object is inserted into the opening, unplug the AC cord of the TV and contact your dealer for
service.
Install the lamp cartridge securely. Failure to do so may cause a fire.
Do not touch the lamp glass elements. Oils from your fingers may cause premature lamp failure.
Hg
= MERCURY
THE LAMP INSIDE THIS PRODUCT CONTAINS MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance at www.eiae.org
For assistance call 1(800) 332-2119
30
Appendices
Appendix B: Lamp-Cartridge Replacement, continued
Replacement Procedure
Removing the Old Lamp Cartridge
Figure 1
1. Turn off TV power and unplug the TV. Allow the
2.
3.
4.
5.
6.
lamp to cool for at least one hour before proceeding.
After the lamp has cooled, remove the cover of the
lamp compartment, located on the back of the TV.
Refer to figures 1 and 2. Use a #2 (medium) Phillips
screwdriver to loosen the screws securing the
cover.
Keep the screws and cover for re-installation
With a medium Phillips screwdriver, loosen the
screw securing the lamp cartridge until it disengage
from the mating threads. This is a captive screw
and cannot be separated from the lamp cartridge.
Fully open the bag supplied with the replacement
lamp and set the opened bag aside.
Gently grasp the handle of the lamp cartridge and
pull the old cartridge straight out. See figure 3.
CAUTION: Do not tilt or rotate the cartridge, as
small glass fragments may fall out.
Without tilting or putting down the lamp cartridge,
insert it into the opened bag. Close the bag while
being careful not to let any glass particles fall out.
Installing the New Lamp Cartridge
1. Do not touch the glass parts of the new lamp car-
2.
3.
4.
tridge. Insert the new cartridge into the TV in the
same orientation as the old cartridge. Push on the
cartridge housing until it is fully seated.
Gently tighten the lamp screw with the screwdriver.
AVOID OVERTIGHTENING!
Replace the plastic cover and retaining screws.
WASH YOUR HANDS THOROUGHLY, AS THIS
LAMP CONTAINS MERCURY.
For assistance call 1(800) 332-2119
Figure 2
Step 3
Figure 3
Use only replacement lamp part number
915B455012
Disposal of the Old Lamp Cartridge
Contact your local authorities or the Electronic Industries
Alliance at www.eiae.org for lamp-disposal or recycling instructions. Do not dispose of the old lamp with
common trash.
Appendices
31
Appendix C: Troubleshooting
TV Reset Comparison Guide
You can resolve many common TV problems using the
reset functions described in the following table.
IMPORTANT
Before you change sound or picture settings: If
picture or sound settings seem wrong for a broadcast
channel (a channel from the ANT input, a cable box, or
satellite receiver), first check other channels from the
same input before changing settings. If most other
channels from the same input seem correct, there is
likely a problem with the broadcast rather than with the
TV. Use care in this case, as changes you make to fix
problems on individual channels also affect all other
channels on the same input.
Additional troubleshooting tips are in the supplemental Owner’s Guide at www.mitsubishi-tv.com.
Reset Name
When to Use
How to Use
Resulting Action
Format
If the picture shape
seems incorrect, use
the FORMAT key to
change the picture
shape.
Press FORMAT to cycle through the
picture shapes available for the
signal.
The last-used format for the signal
type will be recalled on the input.
Note: Also check the aspect
ratio feature on your cable box or
satellite receiver as this may be
altering the picture.
842 Series.
PerfectColor™/
PerfecTint™
Reset
(for the single
current input)
1. While viewing the input to reset,
When the color
press MENU and go to Picture >
intensities seem out
Perfect.
of balance, use the
PerfectColor/PerfecTint 2. Press ENTER to display the
reset to reset the color
PerfectColor adjustment screen.
balances to the original
3. Press CANCEL to reset the colors.
factory settings.
Both PerfectColor and
PerfecTint are reset at
the same time.
All PerfectColor/PerfecTint
sliders are reset to the original
center position. The PefectColor/
PerfecTint settings for other
inputs remain unchanged.
A/V Memory
Reset
(for the single
current input)
When audio and/or video 1. While viewing the input to reset,
settings for a single input
press MENU and go to Picture >
seem incorrect, use A/V
Reset.
Memory Reset to return 2. Press to highlight Reset.
the input to the original
3. Press ENTER again to reset.
factory settings.
Most Audio and Video settings
for the individual input are reset
except for the global settings
for audio Balance, Listen To,
Language, and Advanced.
A/V Reset
(for all inputs)
To reset audio and
video adjustments for
all inputs to the original
factory settings.
While viewing the TV, press the
control-panel buttons INPUT and
VOLUME DOWN at the same time for at
least two seconds.
Most Audio and Video settings
are returned to the original
factory settings, including global
settings not affected by Picture
> Reset. Settings under Picture
> Advanced are unaffected.
Channel
Memorization
To erase and re-memorize channels on the
Ant input.
1. Press MENU and go to Setup >
Channel.
2. Highlight the reception mode,
e.g. Ant Air, and press ENTER.
3. Highlight All Channels and
press ENTER.
4. Highlight Scan.
5. Press ENTER to start channel
memorization.
All previously memorized channels for the antenna input are
erased and a new set of memorized channels is created. All
channel information in the FAV
menu and Channel Lock is
deleted. To add or delete individual channels, use the Setup >
Channel > Edit menu.
Lock Menu
Pass Code
To change your Lock
menu pass code
Press the 9 and LAST keys simultaneously to temporarily unlock the TV. See
the supplemental Owner’s Guide at www.mitsubishi-tv.com for more.
For assistance call 1(800) 332-2119
32
Appendices
Appendix C: Troubleshooting, continued
Reset Name
When to Use
How to Use
Resulting Action
Control-Panel
Lock Release
To re-enable the
control-panel buttons
after activation of the
Control-Panel Lock
Press and hold the INPUT button on
the control panel for ten seconds. If
the TV is powered off, you can now
press the POWER button to turn it on.
Allows the control panel to be
unlocked if the remote control is
misplaced.
System Reset
If the TV does not turn
on or off, does not
respond to the remote
control or controlpanel buttons, or has
audio but no video.
Press and hold the POWER button on
the control panel for ten seconds.
The TV will turn off. The green
LED will flash quickly for about
one minute. The changes you
made most recently, before using
SYSTEM RESET, may be lost.
TV Reset
To reset all consumeraccessible settings
and all memories to
the original factory
defaults.
IMPORTANT:
Use this reset
only if other
troubleshooting
has been unsuccessful.
1. While viewing the TV, press
MENU to display the TV main
menu.
2. With the main menu displayed,
press number keys 1 2 3 to
display the Reset menu.
Use TV Reset if the TV
3. READ THE ON-SCREEN
can respond to conWARNING AND INSTRUCtrols but TV behavior is
TIONS.
abnormal.
• If you do not wish to use this
CAUTION: All ownerreset, press EXIT or MENU to
performed setups and
back out.
adjustments will be
• If you wish to continue,
erased.
press ENTER to erase all
memories and settings.
The TV will start the initialization
process and then turn off.
The front green LED will start
flashing. All memory and
settings outlined in this Owner’s
Guide will need to be set again.
Service and Customer Support
Service
If you are unable to correct a problem with your
TV, consult Mitsubishi Consumer Relations at
1 (800) 332-2119.
•
•
DO NOT adjust any controls other than those
described in this Owner’s Guide and the on-line
supplemental Owner’s Guide.
DO NOT remove the protective back cover of your TV.
For assistance call 1(800) 332-2119
Customer Support
•
•
To order replacement or additional remote controls,
visit our website at www.mitsuparts.com or call
1 (800) 553-7278.
For questions:
-- Call Consumer Relations at 1 (800) 332-2119.
-- E-mail: TVsupport@mevsa.com
-- Website: www.mitsubishi-tv.com
Appendices
33
Appendix C: Troubleshooting, continued
Common Picture Problems
Symptom
1.
Remarks
Picture does not look like a high-definition picture.
Compare the picture to the TV’s test picture (Picture > Picture+
menu) to check if the source signal is supplying a lesser-quality
image.
Not all signals are high-definition signals. To receive high-definition
programming from your cable or satellite provider, you must subscribe to the provider’s high-definition service. Some over-the-air
broadcasts are in high-definition and can be received with a highquality antenna suited to your location.
2.
TV has sound but no picture.
•
•
•
3.
A color program appears as a black
and white image, or the colors are
dim, or the screen is black.
•
•
•
4.
Picture from an HDMI input is noisy
(poor quality).
•
•
Press MENU on the remote control. If the menu displays, then
there is a problem with the incoming signal.
Check that all video inputs are plugged in firmly to the correct
input jacks.
Press and hold the POWER button on the control panel for ten
seconds to perform System Reset.
If using component video, check that the red, green, and blue
input cables are correctly connected to the red, green, and blue
component video jacks.
If using composite video, check that the incoming cable is connected the TV’s green Y/VIDEO jack.
842 Series. The PerfectColor color balance has been incorrectly
set. Reset the PerfectColor balance.
Compare the picture to the TV’s test picture (Picture > Picture+
menu) to check the source of the noise.
Upgrade a standard (unmarked) HDMI cable to a high-speed
HDMI cable.
Front-Panel STATUS Light
LED Color
TV Condition
Green
TV is powered on. Normal operation.
Green
TV powered off, auto-on TV Timer is set.
Normal operation. TV can be turned on at any time.
Green
TV just powered off and lamp is cooling. Sixty seconds after turning off TV,
LED will start to blink. TV can be turned back on before blinking starts or after
blinking stops, but not while the indicator is blinking. Normal operation.
Yellow
TV is too hot. The TV will display a warning message and shut off if it overheats.
• Ambient room temperature may be too high. Turn off the TV and let the room
temperature drop.
• Clear blocked air vents. Ensure at least a four-inch clearance on all sides of the TV.
Yellow
Lamp access door is not secure or no lamp installed.
TV will not operate until lamp access door is secured. See Appendix B.
Red
Lamp failure. Replace the lamp. See Appendix B.
Red/
Yellow
TV may require service.
• Hold power button on front panel for 10 seconds to reset TV.
• If LED continues to flash red and yellow after reset, unplug the TV from the
AC power source. Wait one minute and then plug the set back in.
• If LED continues to flash red and yellow, go to www.mitsubishi-tv.com or
call 1-800-332-2119 to receive Authorized Service Center information.
You may be asked to count how many times the LED flashes each color to
aid in troubleshooting.
Key
Off
Steady On
Slow Blinking
Fast Blinking
For assistance call 1(800) 332-2119
34
Mitsubishi TV Software
Mitsubishi TV Software
END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE
IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and
Mitsubishi Electric Visual Solutions America, Inc. (MEVSA) for all software pre installed and/or provided along with this television
(“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
The Software is protected by United States copyright laws and international treaty provisions, as well as other intellectual property laws
and treaties. The Software is licensed, not sold.
1.
LICENSE GRANT. MEVSA grants you a non-exclusive, non-transferable, limited right and license to use one copy of the
Software only with the Mitsubishi television model that included this owner’s guide and owned by you.
2.
RIGHTS AND LIMITATIONS.
Software Not for Resale. You may not resell or otherwise transfer for value the Software, except in conjunction with a sale of the TV that
Software has been pre installed.
Prohibition on Reverse Engineering, Decompilation and Disassembly. The Software contains trade secrets or other proprietary material
in its human perceivable form and to protect them, you may not reverse engineer, decompile, or disassemble, or otherwise reduce the
Software to any human perceivable form, except to the extent that the foregoing restriction is expressly prohibited by applicable law.
Separation of Components. The Software is licensed as a single product. Its component parts may not be separated for use on more
than one TV.
No Rental. You may not rent, lease, lend, or sublicense the Software.
Trademarks. This License Agreement does not grant you any rights to any trademarks of MEVSA.
Updates. MEVSA may elect, but shall be under no obligation, to provide you with customer support and/or software upgrades,
enhancements, or modifications to the Software. Depending on the Mitsubishi TV model and internet access capability, MEVSA may
directly, or indirectly via third parties, update or change such Software, in whole or in part, at any time and without notice to you.
3.
VIOLATIONS. You understand that any use, copying or transfer of the Software, except as permitted pursuant to this License,
may subject you to serious criminal and civil penalties including damages and an award to MEVSA of attorneys’ fees in connection with
any violation of this License. You further understand that you may be held legally responsible for any copyright infringement or other
violation of intellectual property rights that is caused, encouraged, or induced by your failure to abide by the terms of the License. This
license is effective until terminated, and will terminate immediately without notice from MEVSA or judicial resolution if you fail to comply
with any provision of this License.
4.
COPYRIGHT. All title and intellectual property rights in and to the Software (including but not limited to any images, photographs,
animations, video, audio, music, text, and “applets” incorporated into the Software), and any accompanying printed materials are owned
by or licensed to MEVSA. All title and intellectual property rights in and to the content which may be accessed through use of the
Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws
and treaties. This License Agreement grants you no rights to use such content, except that you own the media on which the Software is
recorded, but MEVSA and its licensors retain ownership of the Software itself. All rights not expressly granted are reserved by MEVSA.
5.
EXPORT RESTRICTIONS. MEVSA is licensing the Software for use within the United States. You agree that you will not
export or re-export the Software. You specifically agree not to export or re-export the Software: (i) to any country to which the U.S. has
embargoed or restricted the export of goods or services, which currently include, but are not necessarily limited to Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to transmit or transport the Software
back to such country; (ii) to any person or entity who you know or have reason to know will utilize the Software in the design, development,
or production of nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from participating in
U.S. export transactions by any federal agency of the U.S. government. You warrant and represent that neither the BXA nor any other U.S.
federal agency has suspended, revoked, or denied your export privileges.
6.
DISCLAIMER OF WARRANTY. EXCEPT AS OTHERWISE PROVIDED IN THIS LICENSE OR IN THE LIMITED WARRANTY
APPLICABLE TO THE TV, MEVSA MAKES NO OTHER WARRANTIES OF ANY KIND WHATSOEVER REGARDING THE SOFTWARE
AND HEREBY EXPRESSLY DISCLAIMS ALL WARRANTIES OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH
RESPECT TO THE SOFTWARE. ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY DISCLAIMED BY MEVSA. IN
NO EVENT SHALL MEVSA BE LIABLE TO YOU OR ANY THIRD PARTIES, IN CONTRACT, IN TORT OR OTHERWISE, FOR ANY
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE. BECAUSE SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES, THE ABOVE LIMITATION MAY
NOT APPLY TO YOU.
7.
LIMITATION OF LIABILITY. MEVSA SHALL NOT, UNDER ANY CIRCUMSTANCES BE LIABLE TO YOU OR ANY THIRD
PARTIES FOR ANY DAMAGES OF ANY NATURE, WHETHER INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
OTHERWISE, INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOST PROFITS, LOSS OF GOOD WILL OR EXPENDITURES
MADE OR COMMITTED FOR IN RELIANCE ON THE CONTINUATION OF THIS LICENSE. YOU AGREE THAT NEITHER MEVSA’S
BREACH OF THIS LICENSE NOR ITS FAILURE TO REPAIR A DEFECT, ERROR OR BUG SHALL CONSTITUTE A FAILURE OF THE
ESSENTIAL PURPOSE OF THIS LICENSE. BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. MEVSA’s
liability to you for direct damages for any cause whatsoever and regardless of the form of the action, will be limited to the money
paid by you for the TV (based on fair market value of the TV) that caused the damages.
8.
GENERAL. This License Agreement will be governed by the laws of the State of California.
For assistance call 1(800) 332-2119
Mitsubishi TV Software
35
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991
Free Software Foundation, Inc.
675 Mass Ave, Cambridge, MA 02139, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and
change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source
code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program
proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”,
below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion
of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is
covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along
with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties
under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these
conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program
is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on
the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works
based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable
copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the
program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that
is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of
the source code, even though third parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and
will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties
remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its
terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to
these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License
and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those
who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of
the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may
add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published
by the Free Software Foundation.
If you are interested in obtaining open source code for this product, please contact Mitsubishi at
1 (800) 332-2119. A nominal handling and mailing charge may apply.
For assistance call 1(800) 332-2119
36
Mitsubishi TV Software
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our
free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS
WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE
PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY
TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/>
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the GNU General Public License is intended to guarantee your freedom to share
and change all versions of a program--to make sure it remains free software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other work
released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for them if you wish),
that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you received. You must make sure that they, too, receive or can get the source
code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps: (1) assert copyright on the software, and (2) offer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’ sake, the GPL requires that modified versions be marked as changed, so that
their problems will not be attributed erroneously to authors of previous versions.
Some devices are designed to deny users access to install or run modified versions of the software inside them, although the manufacturer can do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of the GPL to
prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision to those domains in future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software on general-purpose computers, but in those that do, we wish to avoid the special
danger that patents applied to a free program could make it effectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS
0. Definitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an exact copy. The resulting work is called a “modified version” of the earlier work or a
work “based on” the earlier work.
A “covered work” means either the unmodified Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a
private copy. Propagation includes copying, distribution (with or without modification), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that (1) displays an appropriate copyright notice, and (2) tells the user that there is no
warranty for the work (except to the extent that warranties are provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user commands or options, such as a menu, a prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modifications to it. “Object code” means any non-source form of a work.
A “Standard Interface” means an interface that either is an official standard defined by a recognized standards body, or, in the case of interfaces specified for a particular programming language, one that is widely used among
developers working in that language.
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging a Major Component, but which is not part of that Major Component, and (b)
serves only to enable use of the work with that Major Component, or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this context, means a
major essential component (kernel, window system, and so on) of the specific operating system (if any) on which the executable work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those
activities. However, it does not include the work’s System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work. For
example, Corresponding Source includes interface definition files associated with source files for the work, and the source code for shared libraries and dynamically linked subprograms that the work is specifically designed to
require, such as by intimate data communication or control flow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as
provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force. You may convey covered works to others for the sole purpose of having them
make modifications exclusively for you, or provide you with facilities for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright. Those thus
making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that prohibit them from making any copies of your copyrighted material outside their relationship
with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it unnecessary.
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an effective technological measure under any applicable law fulfilling obligations under article 11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting
or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered
work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice; keep intact all notices
stating that this License and any non-permissive terms added in accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along with the
Program.
You may charge any price or no price for each copy that you convey, and you may offer support or warranty protection for a fee.
5. Conveying Modified Source Versions.
You may convey a work based on the Program, or the modifications to produce it from the Program, in the form of source code under the terms of section 4, provided that you also meet all of these conditions:
a)The work must carry prominent notices stating that you modified it, and giving a relevant date.
b)The work must carry prominent notices stating that it is released under this License and any conditions added under section 7. This requirement modifies the requirement in section 4 to “keep intact all notices”.
c)You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License will therefore apply, along with any applicable section 7 additional terms, to the whole of the
work, and all its parts, regardless of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such permission if you have separately received it.
d)If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume
of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable Corresponding Source under the terms of this License, in one of these ways:
a)Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the Corresponding Source fixed on a durable physical medium customarily used for software interchange.
b)Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a written offer, valid for at least three years and valid for as long as you offer spare parts or customer
support for that product model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the product that is covered by this License, on a durable physical medium
customarily used for software interchange, for a price no more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source from a network server at no charge.
c)Convey individual copies of the object code with a copy of the written offer to provide the Corresponding Source. This alternative is allowed only occasionally and noncommercially, and only if you received the object code
with such an offer, in accord with subsection 6b.
d)Convey the object code by offering access from a designated place (gratis or for a charge), and offer equivalent access to the Corresponding Source in the same way through the same place at no further charge. You need
not require recipients to copy the Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding Source may be on a different server (operated by you or a third
party) that supports equivalent copying facilities, provided you maintain clear directions next to the object code saying where to find the Corresponding Source. Regardless of what server hosts the Corresponding Source, you
For assistance call 1(800) 332-2119
Mitsubishi TV Software
37
remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e)Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Source of the work are being offered to the general public at no charge under subsection
6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work.
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a
dwelling. In determining whether a product is a consumer product, doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical or common
use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses, or expects or is expected to use, the product. A product is a consumer product regardless of
whether the product has substantial commercial, industrial or non-consumer uses, unless such uses represent the only significant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and execute modified versions of a covered work in that User Product from a modified
version of its Corresponding Source. The information must suffice to ensure that the continued functioning of the modified object code is in no case prevented or interfered with solely because modification has been made.
If you convey an object code work under this section in, or with, or specifically for use in, a User Product, and the conveying occurs as part of a transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a fixed term (regardless of how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information. But this
requirement does not apply if neither you nor any third party retains the ability to install modified object code on the User Product (for example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates for a work that has been modified or installed by the recipient, or for the User
Product in which it has been modified or installed. Access to a network may be denied when the modification itself materially and adversely affects the operation of the network or violates the rules and protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and
must require no special password or key for unpacking, reading or copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional permissions that are applicable to the entire Program shall be treated as though
they were included in this License, to the extent that they are valid under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but the entire
Program remains governed by this License without regard to the additional permissions.
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it. (Additional permissions may be written to require their own removal in certain cases
when you modify the work.) You may place additional permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of that material) supplement the terms of this License with terms:
a)Disclaiming warranty or limiting liability differently from the terms of sections 15 and 16 of this License; or
b)Requiring preservation of specified reasonable legal notices or author attributions in that material or in the Appropriate Legal Notices displayed by works containing it; or
c)Prohibiting misrepresentation of the origin of that material, or requiring that modified versions of such material be marked in reasonable ways as different from the original version; or
d)Limiting the use for publicity purposes of names of licensors or authors of the material; or
e)Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
f)Requiring indemnification of licensors and authors of that material by anyone who conveys the material (or modified versions of it) with contractual assumptions of liability to the recipient, for any liability that these contractual
assumptions directly impose on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along
with a term that is a further restriction, you may remove that term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work material governed by
the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source files, a statement of the additional terms that apply to those files, or a notice indicating where to find the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above requirements apply either way.
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until the copyright holder explicitly and finally terminates your license, and (b)
permanently, if the copyright holder fails to notify you of the violation by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder notifies you of the violation by some reasonable means, this is the first time you have received notice of violation of this
License (for any work) from that copyright holder, and you cure the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this License. If your rights have been terminated and not permanently reinstated, you do
not qualify to receive new licenses for the same material under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy
likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License. Therefore, by
modifying or propagating a covered work, you indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that work, subject to this License. You are not responsible for enforcing compliance
by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or merging organizations. If propagation of a covered work results from an entity
transaction, each party to that transaction who receives a copy of the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable efforts.
You may not impose any further restrictions on the exercise of the rights granted or affirmed under this License. For example, you may not impose a license fee, royalty, or other charge for exercise of rights granted under this
License, and you may not initiate litigation (including a cross-claim or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, offering for sale, or importing the Program or any portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired, that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims that would be infringed only as a consequence of further modification of the contributor version. For purposes of this definition, “control” includes the right to
grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents
of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent (such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to copy, free of charge and under the terms of this License, through a publicly available
network server or other readily accessible means, then you must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benefit of the patent license for this particular work, or (3)
arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients. “Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your recipient’s use of the covered work in a country, would infringe one or more identifiable patents in that country that you have reason to believe are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work, and grant a patent license to some of the parties receiving the covered work
authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-exercise of one or more of the rights that are specifically granted under this
License. You may not convey a covered work if you are a party to an arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the extent of
your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work from you, a discriminatory patent license (a) in connection with copies of the covered work
conveyed by you (or copies made from those copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license
was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a covered work
so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate you to collect a royalty
for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and this License would be to refrain entirely from conveying the Program.
13. Use with the GNU Affero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version 3 of the GNU Affero General Public License into a single combined work, and
to convey the resulting work. The terms of this License will continue to apply to the part which is the covered work, but the special requirements of the GNU Affero General Public License, section 13, concerning interaction
through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address
new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies that a certain numbered version of the GNU General Public License “or any later version” applies to it, you have the option of following the terms
and conditions either of that numbered version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose any
version ever published by the Free Software Foundation.
If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version for the Program.
Later license versions may give you additional or different permissions. However, no additional obligations are imposed on any author or copyright holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal effect according to their terms, reviewing courts shall apply local law that most closely approximates an absolute waiver of all civil
liability in connection with the Program, unless a warranty or assumption of liability accompanies a copy of the Program in return for a fee.
For assistance call 1(800) 332-2119
38
Mitsubishi TV Software
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public
License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the
software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically
libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest
you first think carefully about whether this license or the ordinary General Public License is the better strategy to use
in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if
you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces
of it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the
library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the
rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code
with the library, you must provide complete object files to the recipients, so that they can relink them with the library
after making changes to the library and recompiling it. And you must show them these terms so they know their
rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which
gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the recipients should know that what they have is not the original
version, so that the original author’s reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that
a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full
freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license,
the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free
programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is
legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore
permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License
permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the
ordinary General Public License. It also provides other free software developers Less of an advantage over competing
non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library.
For assistance call 1(800) 332-2119
Mitsubishi TV Software
39
A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is
little to gain by limiting the free library to free software only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use
a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of
a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified
version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from
the library, whereas the latter must be combined with the library in order to run.
•
This product includes software developed by Independent JPEG Group.
•
This product includes software developed by the FreeType Project.
The FreeType Project is copyright (C) 1996-2000 by David Turner, Robert Wilhelm, and Werner Lemberg. All rights
reserved.
•
OpenSSL License
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.
openssl.org/)
•
Original SSLeay License
This product includes cryptographic software written by Eric Young. (eay@cryptsoft.com)
•
libupnp
Copyright (c) 2000-2003 Intel Corporation
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met:
-- Redistributions of source code must retain the above copyright notice, this list of conditions and the following
disclaimer.
-- Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
-- Neither name of Intel Corporation nor the names of its contributors may be used to endorse or promote
products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
INTEL OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
•
libxml2 is free software available under the MIT License.
The MIT License
Copyright (C) 1998-2003 Daniel Veillard. All Rights Reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated
documentation files (the “Software”), to deal in the Software without restriction, including without limitation the
rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the
Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
For assistance call 1(800) 332-2119
40
Warranty
Mitsubishi Home-Cinema Television Limited Warranty
MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC. (“MEVSA”) warrants as follows to the original purchaser of this
television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason arising from improper
workmanship and/or material:
a. Parts. The lenticular (i.e. front picture) screen is warranted against defects in materials and workmanship for a period
of thirty (30) days from the date of the original purchase at retail. The lamp and all other parts (except any software incorporated into this television) are warranted for a period of one (1) year from the date of the original purchase at retail. We will
repair or replace, at our option, any defective part without charge for the part. Parts used for replacement may be replaced
with those of like kind and quality and may be new or remanufactured. Parts used for replacement are warranted for the
remainder of the original warranty period.
b. Embedded Software. MEVSA warrants that all software developed by MEVSA and incorporated into this television set
(the “Embedded Software”) will perform in accordance with the functional description of Embedded Software in all material respects, but MEVSA does not warrant that the Embedded Software is error-free. The limited warranty contained in
this section shall continue for a period of one (1) year from the date of the original purchase at retail. If, after prompt notice
within the warranty period, MEVSA determines that the Embedded Software has failed to perform in accordance with such
functional description in all material respects and if such failure is not due to accident, misuse, modification or misapplication of the Embedded Software, then MEVSA shall modify the nonconforming Embedded Software and make available the
modified Embedded Software at no charge to you, which at MEVSA’s sole discretion may be fulfilled by means of modification or replacement software contained on a replacement memory card or made available through download via the Internet
or email for Customer installation. The foregoing shall be MEVSA’s sole obligation to you under this limited warranty. All
rights under this limited warranty on the Embedded Software also subject to your acceptance of and compliance with the
terms of the Software License Agreement applicable to this television, and this limited warranty on the Embedded Software
shall be null and void if the Embedded Software is modified or changed in any manner except as specifically authorized by
MEVSA.
c. Labor. For thirty (30) days after the original purchase at retail, we will repair or replace, at our option, the lenticular screen
if it proves defective. For certain items that are designed to be replaced by the consumer, including (but not limited to) some
Embedded Software and Lamps, the consumer is solely responsible for any replacement labor. For all other parts, we will
provide the labor for a warranty repair by an authorized MITSUBISHI service center without charge for one (1) year from the
original date of purchase at retail.
d. Notice. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the
applicable warranty time period.
e. This DLP Projection Television uses a single DLP chip to create the screen image. This technology creates the image
using small dots, or picture elements (pixels). Your DLP Projection TV is manufactured to a high level of performance and
quality, in fact, 99.99% perfect in the number of properly functioning pixels. As in other display technology, sometimes a
pixel is continuously active, inactive or the incorrect color. Our standard is clear; MEVSA warrants only that the percentage
of properly functioning pixels will be not less than 99.99% of all pixels.
BEFORE REQUESTING SERVICE, please review the instruction booklet to insure proper installation and correct
customer control adjustment. If the problem persists please arrange for warranty service.
1. TO OBTAIN WARRANTY SERVICE:
a. Contact your nearest authorized MITSUBISHI service center, whose name and address can be obtained from your
MITSUBISHI dealer, by writing at the address provided below, calling MEVSA at the 800-332-2119, or by using the support
feature of our website at www.Mitsubishi-tv.com.
b. Warranty service will be provided in your home or, if required, at an authorized service shop, provided that your television
is located within the geographic territory customarily covered by an authorized MITSUBISHI service center. If not, you must
either deliver your television to an authorized service location at your own expense, or pay for any travel and/or transportation costs the service center may charge to and from your home. Actual service labor will be provided without charge.
c. Proof of purchase date from an authorized MITSUBISHI dealer is required when requesting warranty service. Present your
sales receipt or other document which establishes proof and date of purchase. THE RETURN OF THE OWNER REGISTRATION CARD IS NOT A CONDITION OF COVERAGE UNDER THIS LIMITED WARRANTY. However, please return the Owner
Registration Card so that we can contact you should a question of safety arise which could affect you.
d. To obtain a replacement lamp, order the lamp directly from the MEVSA Parts Department at (800) 553-7278.
For assistance call 1(800) 332-2119
Warranty
41
2. THIS LIMITED WARRANTY DOES NOT COVER:
a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated).
b. Damage to the lenticular screen or Fresnel lens, screen frame, cosmetic damage or to any other damage where such
damage is caused by unauthorized modification, alteration, repairs to or service of the product by anyone other than an
authorized MITSUBISHI service center; physical abuse to or misuse of the product (including any failure to carry out any
maintenance as described in the Owner’s Guide including air vent cleaning or any product damaged by excessive physical
or electrical stress); any products that have had a serial number or any part thereof altered, defaced or removed; product
use in any manner contrary to the Owner’s Guide; freight damage; or any damage caused by acts of God or other factors
beyond the reasonable control of MEVSA, such as power surge damage caused by electrical system or lightning. This
limited warranty also excludes service calls where no defect in the product covered under this warranty is found, service
calls related to unsatisfactory audio or visual reception or signal unless caused by a defect in the product that is covered
under this limited warranty, all costs, expenses or any other damages arising from product installation, or set-ups, any
adjustments of user controls (including contrast, brightness, color, tint, fine tuning, sharpness), other adjustment necessary to prepare the unit for display or use, connection with any external audio receiver, antenna, cable or satellite systems,
or service of products purchased or serviced outside the U.S.A. Please consult the operating instructions contained in the
Owner’s Guide furnished with the product for information regarding user controls.
3. ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDY WHICH, BUT FOR THIS PROVISION, MIGHT
ARISE BY IMPLICATION OR OPERATION OF LAW, IS HEREBY EXCLUDED AND DISCLAIMED. THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND OF FITNESS FOR ANY PARTICULAR PURPOSE ARE EXPRESSLY LIMITED TO A TERM OF
ONE YEAR.
4. UNDER NO CIRCUMSTANCES SHALL MEVSA BE LIABLE TO PURCHASER OR ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF
CONTRACT, OR OTHERWISE.
5. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental,
special, or consequential damages, so the above limitations or exclusions may not apply to you.
6. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
7. In the event of any dispute under this limited warranty, jurisdiction and venue for resolving that dispute will be in the state
where the television was purchased and the laws of such state will govern.
MITSUBISHI ELECTRIC VISUAL SOLUTIONS AMERICA, INC.
9351 Jeronimo Road
Irvine, CA 92618-1904
For assistance call 1(800) 332-2119
42
Warranty
Mitsubishi Electric Visual Solutions America, Inc. (MEVSA) Internet Applications Policy
MEVSA Internet Applications affords the opportunity to access third party Internet product offerings or services (“Third Party
Services”) on certain Mitsubishi TVs. The Third Party Services accessible herein are provided as per our agreement with these
third parties. These agreements are subject to change, interruption, suspension (including termination) at any time and for various
reasons. MEVSA makes no warranties or representations that any particular Third Party Service will be accessible, available, function in any particular manner or function at all.
Internet Access Required for Third Party Services; Updates:
To use these Third Party Services, you must obtain high-speed/broadband access to the Internet (such as DSL, cable or T1 lines),
either directly or through devices that access the Internet and pay any service fees associated with such access. In addition, you
must provide all equipment necessary to make such connection to the Internet including a modem or other Internet access device.
Each individual third party Internet product may require different minimum Internet connection speed. The usability and availably
of a functional Mitsubishi television and its internet connected feature may highly be dependent and varied based on high-speed/
broadband internet access, connection speed, bandwidth, other equipment(s), third party applications, firmware updates and other
factors outside of MEVSA’s control and/or responsibility which may also be independent of the actual operation of the television. It
is further understood that Mitsubishi televisions are integrated with sophisticated technologies (software and hardware) which may
exhibit delayed boot-up/shutdown time and/or interrupted services. You further understand that the Third Party Services specifications and functionality are constantly evolving and that we may directly, or indirectly via third parties, update or change the Third
Party Services, in whole or in part, at any time and without notice to you. Such updates may be required for you to use certain
aspects of the Third Party services or to continue to connect to the Third Party Services.
Availability of Content on Third Party Services:
MEVSA or said third parties providing Third Party Services reserve the right to delete data from their servers, or prevent access
to their servers or to change data categories, product offerings or service levels for any reason that MEVSA or said third parties
deem sufficient in their sole discretion at any time, without notice. MEVSA may also impose additional or different limits on the use
of or access to certain Third Party Services, in any case and without notice or liability. Some or all of the data or functionality of
the Third Party Services may require additional payment and/or subscription by you. However, in no event will you be charged for
any Third Party Services unless those charges are made known to you in advance. MEVSA makes no warranties or representations of any kind as to the accuracy, currency, or completeness of any information contained on the data servers of such third party
providers of any Third Party Services. Furthermore, we do not review, control, or endorse the content, products or services of
Third Party Services or their data servers.
THIRD PARTY SERVICES ARE PROVIDED SERVICE “AS IS” AND “AS AVAILABLE,” WITHOUT WARRANTY OF ANY KIND
(INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, NON-INFRINGEMENT, OR FITNESS FOR A PARTICULAR
PURPOSE), TO THE MAXIMUM EXTENT PERMITTED BY LAW. USE OF THE THIRD PARTY SERVICES IS AT YOUR SOLE RISK.
THIS MEANS, FOR EXAMPLE, THAT MEVSA DOES NOT GUARANTEE THAT THE THIRD PARTY SERVICES WILL ALWAYS WORK
PROPERLY OR WORK AT ALL. THIS ALSO MEANS WE DO NOT GUARANTEE THAT THE THIRD PARTY SERVICES, CONTENT
OR PRODUCTS WILL BE FREE FROM VIRUSES, HACKS, OR OTHER POTENTIALLY HARMFUL INTRUSIONS. PLEASE NOTE
THAT SOME STATES DO NOT ALLOW SUCH WARRANTY LIMITATIONS, SO THESE LIMITATIONS MAY NOT APPLY TO YOU.
Third Party Services Content Disclaimer:
Certain Third Party Services may include materials from third parties or links to certain third party data servers. You acknowledge
and agree that MEVSA is not responsible for examining or evaluating the content or accuracy of any Third Party Services, their
data servers or related third-party materials. MEVSA does not warrant or endorse and does not assume and will not have any
liability or responsibility for any third-party materials or web sites, or for any other materials, products, or services of third parties.
Links to Third Party Services and any associated links to other data servers are provided solely as a convenience to you. To the
extent provided, content types or descriptions of Third Party Services provided for convenience, and you acknowledge and agree
that MEVSA does not guarantee their accuracy. You understand that by using any of the Third Party Services, you may encounter
content that may be deemed offensive, indecent, or objectionable, which content may or may not be identified as having explicit
language. Nevertheless, you agree to use the Third Party Services at your sole risk and that MEVSA shall have no liability to you for
content that may be found to be offensive, indecent, or objectionable. You agree that you will not use any third-party materials in a
manner that would infringe or violate the rights of any other party, and that MEVSA is not in any way responsible for any such use
by you.
For assistance call 1(800) 332-2119
Website:
www.mitsubishi-tv.com
E-mail:
TVsupport@mevsa.com
Call Consumer Relations for
operational or connection assistance at 800-332-2119
To order replacement or additional
remote controls or lamp cartridges,
Visit our website www.mitsuparts.com
or call 800-553-7278
Trademark and License Information
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY
EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS,
INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Manufactured under license from Cambridge Mechatronics Ltd.
Rapidfire and the 1... logo are trademarks of Cambridge Mechatronics Ltd
Apple, iPad, iPhone, iTouch, iTunes, are trademarks of Apple Inc., registered in the U.S. and other countries.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such
marks by Mitsubishi Electric is under license. Other trademarks and trade names are those of their respective owners.
TM
Manufactured under license from Real Sound Lab, SIA.
CONEQ is a trademark of Real Sound Lab, SIA.
Digital Light Processing® and DLP® are registered trademarks of Texas Instruments.
Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks
of Dolby Laboratories.
HDMI®, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Imaging Science Foundation Certified Calibration Controls
The software in this TV is based in part on the work of the Independent JPEG Group, copyright © 1991-1998, Thomas
G. Lane, all rights reserved.
VUDU™ is a trademark of VUDU, Inc.
XPAND, X3D, X4D, X6D, their respective logos and other identifying marks of XPAND and X6D Ltd. are and shall
remain the trade-marks and trade names and exclusive property of X6D Ltd.
“x.v.Color” and the “x.v.Color” logo are trademarks of Sony Corporation.
DeepField™ Imager, Easy Connect™, EdgeEnhance™, Plush 1080p® 5G, are trademarks of Mitsubishi Electric Visual
Solutions America, Inc.
VNC is a registered trademark of RealVNC Ltd. in the U.S. and in other countries.
Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
SYSTEM RESET
If the TV does not respond to the remote control,
control-panel buttons, or will not power on/off,
press and hold the POWER button on the control
panel for ten seconds.
The TV will turn off. Power on the TV and the green
LED will flash quickly for about one minute. Recent
settings changes may be lost.
For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the TV.
MODEL NUMBER SERIAL NUMBER PURCHASE DATE RETAILER NAME LOCATION
V47+/V47++853B731A10
© 2012 Mitsubishi Electric Visual Solutions America, Inc.