Zavio F731E 35M User manual

F531E, F731E
0
F531E & F731E User Manual
- CONTENT -
CHAPTER 1 AFETY INSTRUCTION......................................................................3
CHAPTER 2 SYSTEM REQUIREMENT & PRODUCT FEATURE ...................5
2.1. SYSTEM REQUIREMENT ...........................................................................5
2.2. PRODUCT FEATURE ...................................................................................6
CHAPTER 3 USING IP CAMERA VIA WEB BROWSER ....................................7
3.1. WINDOWS WEB BROWSER.......................................................................7
3.2. MAC WEB BROWSER .................................................................................8
CHAPTER 4 USING IP CAMERA VIA MOBILE PHONE .................................10
4.1. MOBILE PHONE VIEWING ......................................................................10
4.2. USING IP CAMERA VIA IPHONE.............................................................11
CHAPTER 5 MSN MESSENGER ...........................................................................12
CHAPTER 6 CONFIGURATION OF MAIN MENU............................................17
6.1. LIVE VIEW ..................................................................................................17
6.2. SETTING......................................................................................................19
6.3. CLIENT SETTING.......................................................................................20
6.4. IMAGE SETUP ............................................................................................21
CHAPTER 7 SETTING-BASIC...............................................................................22
7.1. SYSTEM.......................................................................................................22
7.1.1.
Information ..................................................................................22
7.1.2.
Date/Time.....................................................................................22
7.1.3.
Initialize .......................................................................................23
7.2. CAMERA .....................................................................................................25
7.2.1.
General.........................................................................................25
7.2.2.
MPEG-4 .......................................................................................26
7.2.3.
MJPEG.........................................................................................29
7.3. NETWORK...................................................................................................30
7.3.1.
INFORMATION ..........................................................................30
7.3.2.
PPPoE(Point-to-Point Protocol over Ethernet)............................31
7.3.3.
DDNS(Dynamic DNS) ................................................................33
7.3.4.
UPnP(Universal Plug and Play)...................................................37
7.3.5.
Bonjour ........................................................................................38
7.3.6.
IP Notification..............................................................................38
1
F531E & F731E User Manual
7.3.7.
Messenger ....................................................................................40
7.4. SECURITY ...................................................................................................42
7.4.1.
Account ........................................................................................42
7.4.2.
HTTPS .........................................................................................43
CHAPTER 8 SETTING-ADVANCE .......................................................................44
8.1. FTP CLIENT.................................................................................................44
8.1.1.
General.........................................................................................44
8.1.2.
Alarm Sending .............................................................................45
8.1.3.
Periodical Sending .......................................................................46
8.2. SMTP ............................................................................................................48
8.2.1.
General.........................................................................................48
8.2.2.
Alarm Sending .............................................................................50
8.2.3.
Periodical Sending .......................................................................51
8.3. HTTP EVENT...............................................................................................53
8.3.1.
General.........................................................................................53
8.3.2.
Alarm Sending .............................................................................54
8.4. ALARM OUTPUT........................................................................................57
8.5. SCHEDULE..................................................................................................59
8.6. ALARM INPUT............................................................................................60
8.7. ALARM BUFFER ........................................................................................61
8.8. MOTION DETECTION ...............................................................................62
8.9. SYSTEM LOG..............................................................................................63
APPENDIX.................................................................................................................64
A.
B.
C.
D.
FRAME-RATE AND BITRATE TABLE ....................................................64
STORAGE REQUIREMENT TABLE ........................................................66
TESTING SYSTEM SPECIFICATION ......................................................68
D1 PERFORMANCE OF 16 CHANNEL IP CAMERA ............................68
EUROPE – EU DECLARATION OF CONFORMITY .........................................69
FEDERAL COMMUNICATION COMMISSION INTERFERENCE
STATEMENT .............................................................................................................70
2
F531E & F731E User Manual
Chapter 1 AFETY INSTRUCTION
 Before you use this product
This product has been designed with safety in mind. However, the electrical products
can cause fires which may lead to serious body injury if not used properly. To avoid
such accidents, be sure to heed the following.
 Legal Caution
Video and audio surveillance can be forbidden by laws that vary from country to
country. Check the laws in your local region before using this product for surveillance
purposes.
 Don't open the housing of the product
Don't try to open the housing or remove the covers which may expose yourself to
dangerous voltage or other hazards.
 Don't use the accessories not recommend by the manufacturer
 Heed the safety precautions
Be sure to follow the general safety precautions and the “Operation Notice.”
 Operation Notice - Operating or storage location
Avoid operating or storing the camera in the following locations:
 Extremely hot or cold places
(Operating temperature: 0 °C to + 50 °C [32 °F to 122°F] )
 Exposed to direct sunlight for a long time, or close to heating equipment (e.g.,
near heaters)
 Close to water (e.g.,near a bathtub, kitchen sink, laundry tub)
 Close to sources of strong magnetism
 Close to sources of powerful electromagnetic radiation, such as radios or TV
transmitters
 Locations subject to strong vibration or shock
3
F531E & F731E User Manual
 In case of a breakdown
In case of system breakdown, discontinue use and contact your authorized dealer.
 In case of abnormal operation
 If the unit emits smoke or an unusual smell,
 If water or other foreign objects enter the cabinet, or
 If you drop the unit or damage the cabinet:1 Disconnect the cable and the
connecting cables. 2 Contact your authorized dealer or the store where you
purchased the product.
 Transportation
When transporting the camera, repack it as originally packed at the factory or in
materials of equal quality.
 Ventilation
To prevent heat buildup, do not block air circulation around the device.
 Cleaning
 Use a soft, dry cloth to clean the external surfaces of the device. Stubborn stains
can be removed using a soft cloth dampened with a small quantity of detergent
solution, then wipe dry.
 Do not use volatile solvents such as alcohol, benzene or thinners as they may damage
the surface.
4
F531E & F731E User Manual
Chapter 2 SYSTEM REQUIREMENT &
PRODUCT FEATURE
2.1. SYSTEM REQUIREMENT
We strongly recommend your computers follow our minimum requirements in
order to use this IP-Camera normally. If computer level is lower than this, it might
cause some problems.
Item
Requirements
CPU
Pentium 4 1600MHz (or equivalent AMD)
Graphic Card
64 MB RAM graphic cards(or equivalent on-board graphic cards)
RAM
512 MB
Operating System
Windows 98, Windows ME (Please see Note)
Windows2000, 2003, XP, Vista, Mac OS X Leopard
Web Browser
Internet Explore 6 or later
Note:
1. If you are using Windows 98 or Windows ME, please install IP Installer before
using WEB UI to ensure the system runs normally.
2. If you can't view the record video file, please install Xvid codec while installing
Intelligent IP Installer. (For Windows 98, ME or 2000 server, the codec might not
work properly. You’ll need to download Xvid codec 1.0 from the internet.
3. Please always update the latest Windows component. (.Net Framework, Windows
Media Player, Enhance ActiveX Security)
5
F531E & F731E User Manual
2.2. PRODUCT FEATURE
SYSTEM
Resolutions
Compressing format
Frame Rate
MPEG-4 / Motion JPEG / JPEG:
2 resolutions from 640x480 to 320x240 via API and configuration web page
MPEG-4 / Motion JPEG / JPEG
MPEG-4: Up to 30 fps at 640x480
Motion JPEG: Up to 15 fps at 640x480
Rotation: Mirror, Flip, Mirror Flip
Image settings
Brightness / Contrast / Saturation / Hue
Overlay capabilities: time, date, text and privacy image
Shutter Time
1/7.5 ~ 1/120 sec.
Image snapshot
Yes
Video Recording
Yes
Full Screen Viewing
Yes
Digital Zoom
10x digital
Audio
Two-way (full / half duplex)
Audio compression: G.711 PCM, 8kHz, 64kbit/s
Instant Messenger
Support MSN Live View
Mobile Phone Live View
Through 2.5 WAP, 3GPP, 3G Streaming, and 3G Browser
Alarm Sending
FTP Client / SMTP
Security
Passward Protection / HTTPS encryption / WEP64/128 bit, WPA/WPA2-PSK
Alarm and Event Management
Supported protocols
Input: alarm buffer, alarm input, motion diction
Output: FTP/SMTP/HTTP Event
Bonjour, TCP/IP, DHCP, PPPoE, ARP, ICMP, FTP, SMTP, DNS, NTP,
UPnP, RTSP, RTP, HTTP, TCP, UDP, 3GPP/ISMA RTSP
Simultaneous Connection
Up to 5 users
Operating conditions
-30°C ~ 50 ℃ (-22℉ ~ 122 ℉)
HARDWARE
Lens
IR LEDs / Working Distance
Input / Output
Power
F1.5, 4.0mm board lens (for F531E) / 4.3&6&8mm (selectable for F731E)
8 φ LEDs x 21 (850nm) / 15M (for F531E)
8 φ LEDs x 36 (850nm) / 35M (for F731E)
Alarm Output Max 30W
12V DC, 1A, Max 5W
PoE Build-in IEEE 802.3af
6
F531E & F731E User Manual
Chapter 3 USING IP CAMERA VIA
WEB BROWSER
3.1. WINDOWS WEB BROWSER
1. Start your web browser, and enter the IP address or host name of the IP
camera in the Location / Address field of your browser.
Note :
If you only want to view the video without setting page, enter
“http://<IP>/index2.htm” as your web URL.
2. Use the default account “admin” and default password “admin”.
Note :
The default user name “admin” and the password are set at the factory
for the administrator. You can change them in the Account Menu (Please
check “Setting → Basic → Security → Account”)
3. The monitor image will be displayed in your browser. In the far left side of
main configuration are Setting, Client Setting, and Image Setup. For more
details, you can check Chapter 6.2、Chapter 6.3 and Chapter 6.4.
7
F531E & F731E User Manual
3.2. MAC WEB BROWSER
1. Click the Safari icon, and enter the IP address of the IP camera in the
Location / Address field of your browser.
Note :
If you only want to view the video without setting page, enter
“http://<IP>/index2.htm” as your web URL.
2. Use the default account “admin” and default password “admin”.
Note :
The default user name “admin” and the password are set at the factory
for the administrator. You can change them in the Account Menu (Please
check “Setting → Basic → Security → Account”)
8
F531E & F731E User Manual
3. The monitor image will be displayed in your browser. In the far left side of
main configuration are Setting, Client Setting, and Image Setup. For more
details, you can check Chapter 6.2、Chapter 6.3 and Chapter 6.4.
9
F531E & F731E User Manual
Chapter 4 USING IP CAMERA VIA
MOBILE PHONE
4.1. MOBILE PHONE VIEWING
You can use Zavio Web User Interface via iPhone. Please follow the setting
process below. Then you can use Zavio web UI via iPhone.
1. Select Safari function
2. Enter IP address in your web link.
3. Type name and password.
Default value is admin / admin.
Then click Login In
4. The Zavio User Interface and live
image will show up in the middle of
screen.
Note: It will show continuous snapshots not
a real time video streaming. Therefore, the
recording feature is disabled.
10
F531E & F731E User Manual
4.2. USING IP CAMERA VIA IPHONE
To use IP cameras via mobile phones, please make sure your RTSP is set to “On”
(Default is “On”). To change the settings of IP cameras, Please check “Settings →
Basic → Camera → General.”
4.2.1. 3G Mobile Phone Streaming Viewing
For 3G mobile phone viewing, type “ rtsp://<IP>:<PORT>/video.3gp ” into your
3G Streaming Link. <IP> is the Public IP address of your IP camera; <PORT> is
the RTSP port of your IP camera (Default value is 554.) Example:
rtsp://100.10.10.1:554/video.3gp
Note:
You can also use RTSP clients (RealPlayer, VLn
“rtsp://<IP>:<PORT>/video.3gp” as the Player URL.
4.2.2.
2.5G Mobile Phone WAP Viewing
For 2.5G mobile phone viewing, type “http://<IP>/mobile.wml ” into your 2.5G
WAP Browser. <IP> is the Public IP address of your IP camera.
4.2.3. 2.5G Mobile Phone Browser Viewing
For 2.5G mobile phone viewing, type “http://<IP>/mobile.htm ” into your 2.5G
Web Browser. <IP> is the Public IP address of your IP camera.
11
F531E & F731E User Manual
Chapter 5 MSN MESSENGER
Please see the following steps to set up the Messenger function.
1. Application of a new MSN account: You can download MSN software freely and
create a new MSN account (camera at home) to use Microsoft Live Messenger.
2. Login Account and Password: Go to Setting→Basic→Network→Messenger , set
the Messenger to “ON” . Then, login in new account and password (Camera at
home).
3. IP Notification: Choose “On” at the option of IP Notification. If this feature
switches On, camera will send IP notification to the users who are allowed.
4. Privacy & User & Allow List: Choose “On” at the option of Privacy, then User
column will appear and be able to build Allow List.
5. Log in Working Account: Use your working account to login in the Messenger
software. Then, add the new MSN account (camera at home ).
12
F531E & F731E User Manual
6. The Camera at home will show up with its Public IP and Private IP after enter
“Ping” in the lower key-in column to show up with Public IP and Private IP. (If the
option of IP Notification is “On.”)
7. Click on the small camera icon
webcam”.
. Then, choose “View a new contact's
Camera at home says:
8. The IP Camera will accept your invitation; the live video will show up in the right
screen after few seconds.
13
F531E & F731E User Manual
9. Click Action button and choose Start control panel to use control panel.
10. The dialog box will show up with “This application is not part if Window Live
Message…….”
Tick the box of “Don’t show me this again” and click OK
14
F531E & F731E User Manual
11. The IP Camera will accept your invitation to start Control Panel.
12. You can click Camera icon
you immediately.
to snapshot then the picture will send to
Snapshot
15
F531E & F731E User Manual
13. You can click paint palette icon
showing up with tool bar to set up image.
Then, you can use the tool bar to optimize video Brightness
Saturation
click
and Hue
, Contrast
,
. After the adjustment of all setting, you can still
to make the setting back to the original setting.
Image Setup
16
F531E & F731E User Manual
Chapter 6 CONFIGURATION OF
MAIN MENU
In the far left side of main configuration are Setting, Client Setting, Image Setup.
Please see the content behind for more details. In the right hand side of the below
picture, you can see the Live View screen of web user interface. There are some
functions, such as Snapshot, Zoom and Audio and Video Play.
Snapshot Full Screen
Video Play
Audio Button
Zoom in / Out
6.1. LIVE VIEW
6.1.1. Snapshot
You can capture a still image shot by the camera and save it in your computer.
17
F531E & F731E User Manual
6.1.2. Zoom in / out the image via the monitor window

Click

Pull the
to display the digital zoom in window.
to adjust the digital zoom range, and it will be showed on the above window.

You can use the left click of your mouse to move the
to any where on the
window.
6.1.3. Video play buttons
Symbols
Meaning
Pause the current video
Play the video
Stop the current video
Record the current video
Note:
Concerning the recording storage requirement of your hard disk, please refer to
the APPENDIX / B. Storage Requirement Table.
18
F531E & F731E User Manual
6.1.4. Audio buttons
Symbols
Note
Meaning
mean the speakers of your computer are
Speakers turned on
turned on to transmit the sounds from the
connected IP camera(s)
Speakers turned off
Microphone turned on
mean you can broadcast to the connected
IP camera(s) via the Ethernet using your
microphone
Microphone turned off
Volume control bar
6.2. SETTING
This function is only for the Administrator. Click this button to get into the Basic
and Advancd Setting menu. The former includes for sub-folders, such as System,
Camera, Network, and Security. The latter includes FTP Client, SMTP, Http
Event, Schedule, Motion Detection, and System Log.
19
F531E & F731E User Manual
6.3. CLIENT SETTING
This function is only for the client.
Click this button to control Mode, View Size, Protocol, and Video Buffer.
6.3.1 Mode
Click the pull-down box to choose between MPEG-4 MJPEG, and JPEG video
compression mode. MJPEG streaming is unavailable if RTSP mode is “On.”
(Please check Setting → Basic → Camera → Genera)
6.3.2 View Size
Select the desired display image resolution to 640X480 or 320X240.
6.3.3 Protocol
Select the transferring protocol from TCP, UDP, HTTP and Multicast.
6.3.4 Video Buffer
Turn the Video Buffer function On/Off. The Video Buffer function makes the
streaming more smoothly in unsteady network environment, but might cause a little
delay in live viewing.
20
F531E & F731E User Manual
6.4. IMAGE SETUP
You can use the tool bar to optimize video Brightness, Contrast, Saturation and
Hue.
6.4.1 Brightness
The higher value the brightness is, the brighter the image is.
6.4.2 Contrast
The contrast is a measure of a display system, defined as the ratio of white to black
that the system is capable of producing. The higher value the contrast is, the more
delicate of color you can have.
6.4.3 Saturation
The saturation of a color is determined by a combination of light intensity and how
much it is distributed across the spectrum of different wavelengths. The higher value
the saturation is, the more colorful the image will be.
6.4.4 Hue
Hue is one of the three main attributes of perceived color, affected by different
wavelength of color. With higher value of hue, color will be much more vivid.
6.4.5 Default
After the adjustment of all setting, you can still click Default to make the setting back
to the original setting.
21
F531E & F731E User Manual
Chapter 7 SETTING-BASIC
Click the folder of Basic to display the sub folders including System, Camera,
Network, and Security.
7.1. SYSTEM
Click the folder of System to display the sub-folders including Information, Date /
Time, and Initialize.
7.1.1. Information
The Information page provides the product factory information which includes
Product Name, Firmware Version and Web Version.
7.1.2. Date/Time
The Date/ Time page displays all options of time setting.
22
F531E & F731E User Manual
 Current date / time: This displays the current date and time of this IP
Camera.
 PC clock: This displays the date and time of the monitoring PC clock.
 Date / Time format: You can click the pull down box to select different
time display formats.
 Adjust: You can select one of those four adjusting modes for your IP
Camera.
Keep current setting: Select this mode to keep the current date and time
of this IP Camera.
Synchronize: Select this mode to keep the date and time of this IP
Camera is the same as the monitoring PC.
Manual setting: Select this mode to adjust manually the date and time of
this IP Camera.
Synchronize with NTP: Specify the NTP server name and the Refresh
Interval to synchronize the date and time of this IP Camera with those of
the time server, known as the NTP server.
 Time Zone: You can select the Time Zone of the format from Greenwich
Mean Time. The time will display the same as the current date / time
option.
 Daylight Saving Time: There are two modes to choose for setting up
daylight saving time.
By Date: Set the start and end time by select month, day, hour, and
minute.
By Week Number: Set the start and end time by select month, week,
hour, and minute.
Note:
The NTP server (Network Time Protocol) is the time server which is an
Internet standard protocol built on the top of TCP / IP. This assures
accurate synchronization to the millisecond of computer clock times in a
network of computers.
7.1.3. Initialize
23
F531E & F731E User Manual
 Reboot: Click this bottom to reboot. A confirmation dialogue will appear
and then click “OK” to process. It takes two minutes to reboot this IP Camera.
 Factory Default: Click this bottom to reset this IP Camera to the factory
default setting. A confirmation dialogue will appear and then click “OK” to
process. Don't turn off this IP Camera until the device reboots.
 Backup Setting: You can save the setting data of this IP Camera into a file.
Click “Save” and follow the instructions on the browser to save the setting
data file to your specified location.
 Restore Setting: Download the saved setting data of this IP Camera. Click
“Browse” and select saved file. Click “OK” and this IP Camera is adjusted
according to the loaded data and then restarted.
 Firmware Update: Upgrade the device software. Click “Browse” and
select the file for upgrading. A confirmation dialogue will appear. Click “OK”
to start upgrading. This IP Camera will reboot upon completion.
Note:
Use only upgrade files that are special for this IP Camera. Otherwise
problems may occur. Don't turn off the IP Camera power or disconnect
the network until the upgrading is completed.
Note:
After upgrading new firmware, please execute “Factory Default” first to
make it work.
 Upload Language Pack: Upgrade the device language pack. Click
“Browse” and select the file for upgrading. A confirmation dialogue will
appear. Click “OK” to start upgrading. The upgrade is applied immediately.
The default language is “English.”
24
F531E & F731E User Manual
7.2. CAMERA
Click the folder of Camera to display the sub folders including General, MPEG4
and MJPEG.
7.2.1. General
 RTSP : Switch RTSP “On” or “Off.” The default value is 554.
Note:
RTSP (Real Time Streaming Protocol) is a protocol for use in streaming
media system which allows clients to remotely control a streaming video
server. RTSP is supports by most of the media clients such as Real Player,
QuickTime and VLC...etc.
 Image Rotate: You can mirror or flip the display screen.
 Audio Codec: If this option is selected On, the microphone will start sound
reception.
 Night Mode: You can choose Auto / Off. If you choose Auto option, the
camera will adjust automatically to perform well when the environment is
dark.
 Lighting: You can choose the environment among 50 Hz, 60 Hz , and Auto.
 White Balance: You can choose the white balance to Auto, Florescent,
Incandescent and Black & White.
 IR: You can turn IR light On / Off and Auto. If you select Auto mode, you
25
F531E & F731E User Manual
can adjust threshold for IR Auto-On and Auto-Off respectively. In the right
hand side of threshold, if the tool bar is closer to the right, the IR will auto-on
easily in the dark environment. Conversely, in the left hand side of threshold,
if the tool bar is more approach to the left, the IR will auto-off easily in the
bright environment.
Note:
LED will light up after 10 seconds in dark environment.
 Overlay:
Text Overlay: You can see some information on the display screen
which includes Date / Time and user-defined text. Also, you can change
the background color.
Privacy Mask: You can cover a specific area of the video image.
7.2.2. MPEG-4
A. Computer View
If RTSP is ON, the option of Viewer Authentication & Multicast Streaming will
appear. (Please check “Setting → Basic → Camera → General ”)
 Viewer Authentication: If the viewer authentication is On, the users will be
requested to
key-in username and password when viewing through RTSP.
 Multicast Streaming (If it’s on):
26
F531E & F731E User Manual
Multicast Address:
Specify the multicast server address.
Video / Audio Port: Specify the transmission port number of the video
data. Specify an even number from 1024 to 65534.
Time to Live: Set the maximum TTL that multicast can pass through.
Specify the
value from 1 to 255.
 Image Size: Specify the image size when the network camera transmits.
You can choose among 640 x 480, 320 x 240, and 160 x 120.
 Frame Rate: Set the frame rate of the MPEG4 image. You can choose
values from 1, 2, 3, 4, 5, 7, 10, 15, 20, 25, and 30 fps. The unit “fps” stands for
“frames per second”.
 Quality:
Auto: The quality and bitratee will be adjusted automatically according
to the frame rate.
Fixed Quality: You can select the value of quality among Medium,
Standard, Good, Delicate and Excellent.
Fixed Bitrate: Set the bitrate of MPEG4 image transmission for a line.
You can select the value from 64, 128, 256, 384, 512, 768, 1024, 1280,
1536, and 2048 kbps.
Note:
Concerning how to select the suitable image quality for Fixed Quality or Fixed
Bitrate, please refer to the APPENDIX / A. Frame-rate & Bitrate Table.
B. Mobile View
27
F531E & F731E User Manual
If RTSP is ON, the option of Viewer Authentication & Multicast Streaming will
appear. (Please check “Setting → Basic → Camera → General ”)
Note: If RTSP is off, Mobile View will be disabled.
 Viewer Authentication: If the viewer authentication is On, the users will be
requested to
key-in username and password when viewing through RTSP.
 Multicast Streaming (If it’s on):
Multicast Address: Specify the multicast server address.
Video / Audio Port: Specify the transmission port number of the video
data. Specify an even number from 1024 to 65534.
Time to Live: Set the maximum TTL that multicast can pass through.
Specify the
value from 1 to 255.
 Image Size: The image size of Mobile View is fixed at 320x240 or 160 x
120.
 Frame Rate: Set the frame rate of the MPEG4 image. You can choose
values from 5 and 10fps. The unit “fps” stands for “frames sent per second”.
 Quality:
Auto: The quality and bitratee will be adjusted automatically according
to the frame rate.
Fixed Quality: You can select the value of quality among Medium,
Standard, Good, Delicate and Excellent.
Fixed Bitrate: Set the bitrate of MPEG4 image transmission for a line.
You can select the value from 16, 32, 48, 64, 128, and 256 kbps.
Note:
Concerning how to select the suitable image quality for Fixed Quality or Fixed
Bitrate, please refer to the APPENDIX / A. Frame-rate & Bitrate Table.
28
F531E & F731E User Manual
7.2.3. MJPEG
If RTSP is OFF, the option of Image Size & Frame Rate & Quality will appear.
(Please check “Setting → Basic → Camera → General ”)
 Image Size: Specify the image size when the network camera transmits.
You can choose among 640 x 480, 320 x 240, and 160 x 120.
 Frame Rate: Set the frame rate of the MJPEG image. You can choose
values from 1, 2, 3, 4, 5, 7, 10, and 15 fps. The unit “fps” stands for “frames
per second”.
 Quality:
Auto: The quality will be automatically decided.
Fixed Quality: You can select the value of quality among Medium,
Standard, Good, Delicate and Excellent.
Note:
Concerning how to select the suitable image quality for Fixed Quality or Fixed
Bitrate, please refer to the APPENDIX / A. Frame-rate & Bitrate Table.
29
F531E & F731E User Manual
7.3. NETWORK
Click the folder of Network to display the sub folders including Information,
PPPoE, DDNS, UPnP, Bonjour, IP Notification, Wireless(for wireless models)
and Messenger.
7.3.1. INFORMATION
Display the MAC address of the device.
 Obtain an IP address automatically (DHCP): If a DHCP server is
installed on the network, to select this while the IP address is assigned by the
DHCP server.
 Obtain DNS server address automatically: Select this to obtain the
address of DNS server automatically.
30
F531E & F731E User Manual
 Use the following IP address: Select this when the fixed IP address is set.
IP address: Enter the IP address of the device.
Subnet mask: Enter the subnet mask.
Default gateway: Enter the default gateway.
 Use the following DNS server address: Select this when you set the fixed
address as the IP address of DNS server.
Primary DNS server: Enter the IP address of the primary DNS server.
Secondary DNS server: Enter the IP address of the secondary DNS
server, if necessary.
 HTTP port number: Select 80 in general situations. If you want to use a
port number other than 80, select the text box and enter a port number between
1024 and 65535.
When you have set the HTTP port number to a number other than 80 on
the Network setting page or in the Setup Program, access the device by
typing the IP address of the device on the web browser as follows:
Example: when HTTP port number is set to 2000
http://192.168.1.100:2000/
Note:
The IP Camera needs to be rebooted after it finishes changing the network
setting completely.
Note:
If you connect the IP Camera with your computer directly, the default network
domain of camera is 192.168.1.xx
7.3.2. PPPoE(Point-to-Point Protocol over Ethernet)
If your ISP provides Dynamic IP with authentication by username and password,
type all PPPoE information in this part. When you use the PPPoE function, you
need to turn on the DDNS or IP Notification function at same time.
31
F531E & F731E User Manual
 IP Address: The IP address obtained at the PPPoE connecting with
network.
 User ID: Enter the user ID for authentication necessary for PPPoE
connections. Type it up to 64 characters.
 Password: Enter the password for authentication necessary for PPPoE
connections. Type it up to 32 characters.
 Re-type Password: Re-type the password to confirm.
 Obtain DNS server address automatically: Select this to obtain the
address of DNS server automatically.
 Use the following DNS server address: Select this when you set the fixed
address as the IP address of DNS server.
Primary DNS server: Enter the IP address of the primary DNS server.
Secondary DNS server: Enter the IP address of the secondary DNS
server.
Note :
1. PPPoE (Point-to-Point Protocol over Ethernet): PPPoE is a network
protocol for encapsulating Point-to-Point Protocol frames insider
Ethernet frames. PPPoE connection is used mainly with ADSL service
where individual users connect to the ADSL transceiver (modem) over
Ethernet work. It also widely used in XDSL. (digital affiliate line such as
ADSL, VDSL or SDSL)
2. The IP Camera needs to be rebooted after it finishes changing the
network completely.
3. The IP Camera with Intelligent IP Installer can’t be founded after
turning on the PPPoE and reboot.
32
F531E & F731E User Manual
7.3.3. DDNS(Dynamic DNS)
DDNS is a system which allows the domain name data held in a name server to be
updated in real time. The most common use for DDNS is allowing an internet domain
name to be assigned to a computer with a varying / dynamic IP Address. This makes it
possible for other sites on the internet to establish connection to the machine without
needing to track the IP Address themselves.
 Server name: Choose the DDNS Server from the list.
 User ID: Enter the user ID for authentication necessary for DDNS
connections. Type it up to 64 characters.
 Password: Enter the password for authentication necessary for DDNS
connections. Type it up to 32 characters.
 Re-type password: Re-type the password to confirm.
 Host name: Enter the host name that is registered to the DDNS server.
33
F531E & F731E User Manual
Note :
How to apply DDNS username and Host name??
You can apply DDNS username and Host name by the following steps:
1. Login http://www.dyndns.org, click the Create Account
2. Input all information and follow step by step with DynDNS.
34
F531E & F731E User Manual
3. Login with new account and click Account → My Hosts → Add Host Services
4. Type domain in the Hostname field and select sub-domain
35
F531E & F731E User Manual
5. After type information, check your DDNS service.
6. Type your DDNS User ID, Password and Host name in Setting → Network
→ DDNS. After completing setting, reboot IP Camera.
36
F531E & F731E User Manual
7.3.4. UPnP(Universal Plug and Play)
You can select UPnP function “On” or “Off”.
If a ROUTER is used to access to internet and it supports UPnP IGD function,
please turn on the UPnP Port Forwarding function.
 HTTP port: The default HTTP port is 80. Or the port number can be
entered, ranged from 1024 to 65535.
 SSL port: The default SSL port is 443. Or the port number can be entered,
ranged from 1024 to 65535.
 MPEG4 RTSP port: The default MPEG-4 RTSP Port is 554. Or the port
number can be entered, ranged from 1024 to 65535.
Note :
UPnP (Universal Plug and Play): UPnP is a set of computer network protocol. It
allows devices to connect seamlessly and simplify the implementation of networks
in the home and corporate environments. The device supports UPnP which is
enabled by default. The device will be automatically detected and a new icon will
be added to “My Network Place” if it also enables on your computer. It
provides Port Forwarding for opening a port in a router or firewall in a private
network in order to let a party from the outside world contact a inside user.
37
F531E & F731E User Manual
7.3.5. Bonjour
Bonjour, also known as zero-configuration networking, enables automatic discovery
of computers, devices, and services on IP networks. Bonjour uses industry standard IP
protocols to allow devices to automatically discover each other without the need to
enter IP addresses or configure DNS servers.
 Device Name: Enter Device Name you wish.
Note:
How to use Bonjour in your Windows Browser UI? Please check the link below:
http://www.apple.com/support/downloads/bonjourforwindows.html
7.3.6. IP Notification
When network notify type is set to “ON”, you can send an e-mail notification of the
completion of the network setting.
 Notify Type: You can select the notify type among DHCP, Static IP, and
PPPoE.
 SMTP Server Name: Type the SMTP server name up to 64 characters, or
38
F531E & F731E User Manual
the IP address of the SMTP server.
 SMTP Server Port: You can set port number from 1~65535 according to
your mail server. The default value is 25.
Security
setting: Tick SSL box if the mail server you use has security
restriction.
Note:
If you use g-mail as your mail server, you should set 587 as your port
number and tick SSL box.
 Authentication: Select the authentication required when you send an email.
Off: Select if no authentication is necessary when an email is sent.
On: When authentication is necessary an e-mail is sent, there are SMPT,
POP before SMPT or both three options.
 SMTP: Select if SMTP authentication is necessary when an e-mail is sent.
 POP before SMTP: Select if POP before SMTP authentication is necessary
when an e-mail is sent.
POP server name: It is necessary when the POP before SMTP is
selected in Authentication. Type the POP (receiving mail) server name
up to 64 characters, or type the IP address of the POP server. This
setting is necessary when the SMTP server which sends e-mails
performs authentication using the POP user account.
User name, Password: Type the user name and Password of the user
who has the mail account. This setting is necessary when the SMTP
server which sends e-mails performs authentication.
 Recipient e-mail address: Type the recipient e-Mail address up to 64
characters. You can specify up to three recipient E-mail addresses.
 Administrator e-mail address: Type the Administrator e-Mail address up
to 64 characters. This address is used for reply mail and sending system
messages from the SMTP server.
 Subject: Type the subject/title of the e-Mail up to 64 characters. With
respect to mail which is sent according to the IP notification.
 Message: Type the text of the E-mail up to 384 characters. Default value
provides network information including IP, Port, MAC, Model, Firmware
Version and Web Version.
39
F531E & F731E User Manual
7.3.7. Messenger
If Messenger option is selected On, you can set out the setting of MSN account.
Messenger function provide an easy-connect feature. User can easy to know what
camera’s private and public IP address is.
40
F531E & F731E User Manual
 Protocol: support MSN only.
 Login Account: Camera will use this account to login MSN server. This
MSN account should be applied form http://www.msn.com.
 Password: password for this msn account.
 Re-type password: re-type password to double confirm.
 Alias: This alias will display on MSN like the following which display in
red frame.
 View Mode: You can select Computer View or Mobile View.
Computer
Mobile
View: This mode is the default value.
View: If Messenger function doesn’t work due to the firewall or
the function limit of router, please choose Mobile View.
 Port range: Camera will select one port from this port range for video
transmission.
 IP Notification: Switch the IP notification On / Off. If this feature
switches On, camera will send IP notification to the users who are allowed.
 Privacy: Switch privacy On / Off. When privacy turns on, only those
users in allowed list can access the camera.
 User: Input to this blank to edit allow list.
 Allow list: When privacy turns on, only those users in allow list can access
the camera.
41
F531E & F731E User Manual
7.4. SECURITY
Click the folder of Security to display the sub folders including Account and
HTTPS.
7.4.1. Account
The device fault account and password setting is “admin / admin”. That means
everyone who knows IP address can access the device including all configuration. It is
necessary to assign a password if the device is intended to be accessed by others.
 User name: Set a user name between 4-16 characters.
 Password: Set a password between 4-16 characters.
 Re-type Password: Re-type the password to confirm.
 Viewer Mode: Set the user mode among Admin, Operator, and Viewer.
Different viewer mode has different limits of authority.
The Admin mode has all authority of configuration.
The Operator mode can not only view the Live View but also control the
PTZ (apply in speed dome).
The Viewer mode only can view the Live View.
 Viewer Authentication: Allows any viewer direct access to Live View.
42
F531E & F731E User Manual
7.4.2. HTTPS
HTTPS is a URI scheme used to indicate a secure HTTP connection. It is
syntactically identical to the http:// scheme normally used for accessing resources
using HTTP. Using an https: //URL/ with a different default TCP port (443) and an
additional encryption / authentication layer between the HTTP and TCP. You can
use the IP camera through HTTPS easily by using https:// instead of http://.
 Create & Install: Create a self-signed certificate for HTTPS to recognize.
 Installed Certificate: Display or remove the properties of the installed
certificate.
 HTTPS Connection Policy: Set HTTPS connection policy for different
level of users.
 To use the HTTPS encryption, please set up “Create self-signed
certificate” for the first time you use the HTTPS function, and then set up the
connection policy for different users.
Note:
When enable HTTPS with RTSP on mode, the IP Camera only protect the
setting such as username and password and do not protect video and audio.
When enable HTTPS with RTSP off mode, the IP Camera will protect all setting
including video and audio.
43
F531E & F731E User Manual
Chapter 8 SETTING-ADVANCE
Click the folder of Advance to display the sub folders including FTP client, SMTP,
Schedule, Motion detection and System Log.
8.1. FTP CLIENT
Use this menu to set up for capturing and sending images to an FTP server. By using
FTP client function, you can send the image file which has been shot and recorded
linked with the built-in motion detection function to FTP server. FTP client setting
menu is composed of two tabs, General, Alarm sending and Periodical sending.
8.1.1. General
Select “On” when you use FTP function. The FTP client setting page appears.
Select “Off”, when you do not wish to use the FTP client function.
Note:
The frame rate and operability on the main viewer may decrease while a
file is being transmitted by the FTP client function.
 FTP server name: Type the FTP server name to upload still images up to
64 characters, or the IP address of the FTP server.
 User name: Type the user name for the FTP server.
 Password: Type the password for the FTP server.
44
F531E & F731E User Manual
 Retype password: To confirm the password, type the same characters as
you typed in the Password box.
 Passive mode: Set whether you use the passive mode of FTP server or not
when connecting to FTP server. Select On to connect to FTP server using
the passive mode.
8.1.2. Alarm Sending
Set to forward the image file to the specified FTP server linked with the alarm
detection by the built-in motion detection function. Select On to send the image file
to FTP server linked with the alarm detection.
 Remote Path: Type the path to the destination in FTP server up to 64
characters.
 Image File Name: Type the file name you want to assign to the images
when sending to the FTP server. You can use up to 10 alphanumeric
characters, - (hyphen) and _ (underscore) for naming.
 Suffix: Select a suffix to add to the file name
 Date & time: The date & time suffix is added to the Image file name.
The date/time suffix consists of lower two-digits of year (2 digits),
month (2 digits), date (2 digits), hour (2 digits), minute (2 digits),
second (2 digits), and consecutive number (2 digits), thus 14-digit
number is added to the file name.
Sequence number: A consecutive number of 10 digits between
0000000001 and 4294967295 and two fixed digits 00 is added to the
Image file name.
45
F531E & F731E User Manual
Sequence
number clear: Click Clear and the suffix of the sequence
number returns
to 1.
 Alarm
 Motion
Detection: Click it on for using Motion Detection function as a
sensor. You can set motion detection function at the motion detection
function page.
Note:
You can set motion detection at motion detection page. (Please go “Setting
→ Advance →Motion Detection → Setting”)
 Effective period: Set the period when the periodical sending is effective.
Always: The periodical sending is always effective.
Schedule: You can specify the period when the periodical sending is
effective in the Schedule setting in the other section.
Note:
You can set schedule function at schedule page. (Please go “Setting →
Advance → Schedule → Setting”)
8.1.3. Periodical Sending
You can set to send an image file to FTP server periodically by selecting On to
send the image file to FTP server linked with setting period.
46
F531E & F731E User Manual
 Image file name: Type the file name of the image sent by SMTP up to 10
alphanumeric characters, - (hyphen) and _ (under score).
 Suffix: Select a suffix to be added to the file name sent by SMTP.
None: The name of the sent file will be the Image file name.
Date & time: The date & time suffix is added to the Image file name.
The date & time suffix consists of lower two-digits of year (2 digits),
month (2 digits), date (2 digits), hour (2 digits), minute (2 digits) and
second (2 digits), and consecutive number (2 digits), thus 14-digit
number is added to the file name.
Sequence number: A consecutive number is added to the Image file
name.
Sequence number clear: Click Clear and the suffix of the sequence
number returns to 1.
 Interval: Set the periodical sending is effective interval. Min value is 1 min
and Max value is 24 hour.
 Effective period: Set the period when the periodical sending is effective.
Always: The periodical sending is always effective.
Schedule: You can specify the period when the periodical sending is
effective in the Schedule setting in the other section.
Note:
You can set schedule function at schedule page. (Please go “Setting →
Advance → Schedule → Setting”)
47
F531E & F731E User Manual
8.2. SMTP
Set the SMTP menu when you want to send an image via e-mail. By using Mail
(SMTP) function, you can send a mail with attached image file which has been
shot linked with the external sensor input or with the built-in motion detection
function. The image file can also be sent periodically. E-Mail (SMTP) setting menu
is composed of three tabs, General, Alarm sending and Periodical sending.
8.2.1. General
Select On when you use the SMTP function. The common setting options are
displayed below. Select Off, if you do not wish to use the e-Mail (SMTP) function.
Note :
The Setting of general part will be the same as the setting of IP Notification
(Please check “Setting → Basic → Network → IP Notification”)
 SMTP server name: Type the SMTP server name up to 64 characters, or
the IP address of the SMTP server.
 SMTP Server Port: You can set port number from 1~65535 according to
your mail server. The default value is 25.
48
F531E & F731E User Manual
Security
setting: Tick SSL box if the mail server you use has security
restriction.
Note:
If you use g-mail as your mail server, you should set 587 as your port
number and tick SSL box.
 Authentication: Select the authentication required when you send an email.
Off: Select if no authentication is necessary when an email is sent.
On: When authentication is necessary an e-mail is sent, select one of the
authentication methods from the followings.
 SMTP: Select if SMTP authentication is necessary when an e-mail is sent.
 POP before SMTP: Select if POP before SMTP authentication is necessary
when an e-mail is sent.
Note:
When you set to On, be sure to select either or both SMTP or / and POP
before SMTP.
POP server
name: It is necessary when the POP before SMTP is
selected in Authentication. Type the POP (receiving mail) server name
up to 64 characters, or type the IP address of the POP server. This
setting is necessary when the SMTP server which sends e-mails
performs authentication using the POP user account.
User name, Password: Type the user name and Password of the user
who has the mail account. This setting is necessary when the SMTP
server which sends e-mails performs authentication.
 Recipient e-mail address: Type the recipient e-Mail address up to 64
characters. You can specify up to three recipient E-mail addresses.
 Administrator e-mail address: Type the Administrator e-Mail address up
to 64 characters. This address is used for reply mail and sending system
messages from the SMTP server.
 Subject: Type the subject/title of the e-Mail up to 64 characters. With
respect to mail which is sent according to the alarm detection when Alarm
sending of the alarm tab is set to On, the characters standing for the sensor
type added to the subject.
 Message: Type the text of the E-mail up to 384 characters. (A line break is
equivalent to 2 characters.)
49
F531E & F731E User Manual
8.2.2. Alarm Sending
Set to send the mail with connection to the alarm detection by the built-in motion
detection function. Select On to send the image file to SMTP server linked with the
alarm detection.
 Alarm sending: Select On to set to send mail with connection to the alarm
detection.
 File attachment: Set whether an image file is attached to the mail sent or
not. When On is selected, the image file made by the settings below is
attached. When Off is selected, only the message is sent.
 Image file name: Type the file name you want to assign to the image to
attach a mail. You can use up to 10 alphanumeric, - (hyphen) and _
(underscore) for naming.
 Suffix: Select a suffix to add to the file name
 Date & time: The date & time suffix is added to the Image file name.
The date/time suffix consists of lower two-digits of year (2 digits),
month (2 digits), date (2 digits), hour (2 digits), minute (2 digits),
second (2 digits), and consecutive number (2 digits), thus 14-digit
number is added to the file name.
Sequence number: A consecutive number of 10 digits between
0000000001 and 4294967295 and two fixed digits 00 is added to the
Image file name.
Sequence number clear: Click Clear and the suffix of the sequence
number returns
50
F531E & F731E User Manual
to 1.
 Alarm
 Motion
Detection: Click it on for using Motion Detection function as a
sensor. You can set motion detection function at the motion detection
function page.
Note:
You can set motion detection at motion detection page. (Please go “Setting
→ Advance → Motion detection → Setting”)
 Effective period: Set the period when the periodical sending is effective.
Always: The periodical sending is always effective.
Schedule: You can specify the period when the periodical sending is
effective in the Schedule setting in the other section.
Note:
You can set schedule function at schedule page. (Please go “Setting →
Advance → Schedule → Setting”)
8.2.3. Periodical Sending
You can set to send an image file by SMTP server periodically by selecting On to
send the image file by SMTP server linked with setting period.
51
F531E & F731E User Manual
 Image file name: Type the file name of the image sent by SMTP up to 10
alphanumeric characters, - (hyphen) and _ (under score).
 Suffix: Select a suffix to be added to the file name sent by SMTP.
None:
Date
The name of the sent file will be the Image file name.
& time: The date & time suffix is added to the Image file name.
The date & time suffix consists of lower two-digits of year (2 digits),
month (2 digits), date (2 digits), hour (2 digits), minute (2 digits) and
second (2 digits), and consecutive number (2 digits), thus 14-digit
number is added to the file name.
Sequence
number: A consecutive number is added to the Image file
name.
Sequence
number clear: Click Clear and the suffix of the sequence
number returns to 1.
 Interval: Set the periodical sending is effective interval. Min value is 30
min and Max value is 24 hour.
 Effective period: Set the period when the periodical sending is effective.
Always:
The periodical sending is always effective.
Schedule:
You can specify the period when the periodical sending is
effective in the schedule setting in the other section. Please check
“Setting → Basic → Advance → Schedule → Setting.”
Note:
You can set schedule function at schedule page. (Please go “Setting →
Advance → Schedule → Setting”)
52
F531E & F731E User Manual
8.3. HTTP EVENT
Set up this menu for sending commands to an HTTP server. By using HTTP client
function, you can send the command defined by yourself, linked with the external
sensor input or with the built-in motion detection function to HTTP server. HTTP
Event setting menu is composed of two tabs, General and Alarm sending.
On, and you can start setting up the function.
Select
8.3.1. General
 HTTP Event: Set up the HTTP server URL, port, User ID, Password, and
Proxy Server settings.
For example:
URL: 192.168.1.7/cgi-bin/operator/ptzset
Note:
The setting of URL should be the same as CGI
53
F531E & F731E User Manual
8.3.2. Alarm Sending
Set to send the commands via the alarm detection, external sensor input or built-in
motion detection function. Select On to send the commands to HTTP server linked
with the alarm detection.
Alarm sending: Select On to set to send command with connection to the alarm
detection.
 Alarm
 Motion
Detection: Click it on for using Motion Detection function as a
sensor. You can set motion detection function at the motion detection
function page.
Note:
You can set motion detection at motion detection page. (Please go “Setting
→ Advance → Motion detection → Setting”)
Note:
Motion Detection works only when the MPEG4 function is On.
54
F531E & F731E User Manual

Parameter: the parameter of CGI (defined in URL of HTTP →
General) is from your target device. For example, move=down.

Message: message will show up in the form of Message = PTZ
down. If your target device didn’t support the parameter of
message, you can’t see the message. So you can just take the
message as a note. For example: PTZ down.
Use
Alarm Buffer: Select Use alarm buffer when you forward the
image / audio of before and after the alarm detection (pre-alarm,
post-alarm). If you do not select it, only the image of the moment of the
alarm detection is forwarded. Click Alarm buffer to display the Alarm
buffer setting menu.
Note:
You can set the alarm buffer function at alarm buffer page. (Please go
“Setting → Advance → Alarm buffer → Setting”)

Parameter: the parameter of CGI (defined in URL of
HTTP→General) is from your target device. For example,
move=down.

Message: message will show up in the form of Message = PTZ
down. If your target device didn’t support the parameter of
message, you can’t see the message. So you can just take the
message as a note. For example: PTZ down.
Alarm
Input: Select the connected alarm. Sensor input1: The external
sensor which is connected to sensor input1 of the alarm input.
Note:
You can set the alarm input function at alarm input page. (Please go
“Setting → Advance → Alarm input → Setting”)
55
F531E & F731E User Manual

Parameter: the parameter of CGI (defined in URL of
HTTP→General) is from your target device. For example,
move=down.

Message: message will show up in the form of Message = PTZ
down. If your target device didn’t support the parameter of
message, you can’t see the message. So you can just take the
message as a note. For example: PTZ down.
 Effective period: Set the period when the periodical sending is effective.
Always: The periodical sending is always effective.
Schedule: You can specify the period when the periodical sending is
effective in the Schedule setting in the other section.
Note:
You can set schedule function at schedule page. (Please go “Setting →
Advance → Schedule → Setting”)
56
F531E & F731E User Manual
8.4. ALARM OUTPUT
When you click Alarm output on the Advanced mode menu, the Alarm output
setting menu appears. You can set in this menu to control the alarm out of I / O port
on the rear of the device linked to the alarm detection and the timer.
Alarm output: To activate the Alarm output function, select On. When you do not
use the Alarm output function, select Off.
 Digital output: Select High signal output and Low signal output as your
alarm.
 Trigger condition: Select the mode of the Alarm output function. You can
choose “Alarm” or “Timer”.
 Alarm: Controls alarm output by synchronizing with an external sensor input
or the built-in activity detection function.
 Motion
Detection: Click it on for using Motion Detection function as a
sensor. You can set motion detection function at the motion detection
function page.
Note:
You can set motion detection at motion detection page. (Please go “Setting
→ Advanced → Motion detection → Setting”)
Note:Motion Detection works only when the Video mode is set to MPEG4
57
F531E & F731E User Manual
and the Cropping is set to Off.
 Use
Alarm Buffer: Select Use alarm buffer when you forward the
image / audio of before and after the alarm detection (pre-alarm,
post-alarm). If you do not select it, only the image of the moment of the
alarm detection is forwarded. Click Alarm buffer to display the Alarm
buffer setting menu.
Note:
You can set the alarm buffer function at alarm buffer page. (Please go
“Setting → Advanced → Alarm buffer →Setting ”)
 Alarm
Input: Select the connected alarm. Sensor input1: The external
sensor which is connected to sensor input1 of the alarm input.
Note:
You can set the alarm input function at alarm input page. (Please go
“Setting →Advanced →Alarm input → Setting”)
 Alarm Duration: There are up to 60 second options to choose for alarm
duration interval.
 Effective period: Set the period when the periodical sending is effective.
Always: The periodical sending is always effective.
Schedule: You can specify the period when the periodical sending is
effective in the Schedule setting in the other section.
Note:
You can set schedule function at schedule page. (Please go “Setting →
Advanced → Schedule → Setting”)
58
F531E & F731E User Manual
8.5. SCHEDULE
When you click Schedule on the Advance mode menu, the Schedule setting menu
appears. This is the same menu as the setting menu which is displayed when you
click Schedule to set Effective period and Schedule in FTP client setting menu,
and E-Mail (SMTP) setting menu.
Example: When setting e-Mail (SMTP) (the alarm sending) in the Schedule
setting menu.
 Schedule Selection: Select the list box to specify the schedule you want to
set.
FTP -Alarm
FTP - Periodical
e-Mail (SMTP) -Alarm
e-Mail (SMTP) -Periodical
 Mon (Monday) to Sun (Sunday): The time period on the right of the
checked day is the effective period of the schedule.
 Start time, End time: Specify the Start time and the End time.
 Use the same time schedule every day: When this is checked, the Start
time and End time set to Mon (Monday) are applied to all days. In this case,
the Start time and End time of the other days than Mon (Monday) cannot be
input.
59
F531E & F731E User Manual
8.6. ALARM INPUT
When you click Alarm Input on the Advanced mode menu, the Alarm input setting
menu appears. You can set in this menu to control the external alarm input of I / O
port on the rear of the device linked to FTP, SMTP, and HTTP sending function.
Sensor input 1: Click it on for using external sensor which is connected to sensor
input1 of the camera I / O port.

Trigger condition: Select High signal output and Low signal output as your
alarm.

Camera move: Pull down the window to select the camera preset position.
60
F531E & F731E User Manual
8.7. ALARM BUFFER
You can set the Pre-alarm image and audio (the image and audio before the alarm
detection) and the Post - alarm image and audio. These can be set when Alarm
sending FTP client setting menu or Image memory setting menu is set to On, and
besides when Use alarm buffer is selected.
Alarm buffer: To activate the Alarm buffer function, select On. The basic setting
options are displayed below. When you do not use the Alarm output function, select
Off.
 Recording capacity
Pre-alarm
period: Display the maximum recording capacity of
image/audio before the alarm detection.
Post-alarm
period: Display the maximum recording capacity of
image/audio after the alarm detection.
 Recording time: Set the recording time for the Pre-alarm image/audio and
Post alarm image/audio.
Pre
alarm period: Type it with recording time of the image/audio before
the alarm detection.
Post
alarm period: Type it with recording time of the image/audio after the
alarm detection.
Note:The value of Recording capacity differs depending on Image size,
Bitrate (for MPEG4) and Image quality (for MPEG4 and MJPEG) in the
camera setting menu.
61
F531E & F731E User Manual
8.8. MOTION DETECTION
There are three Motion Detection functions as sensors to set for different detecting
zones. Each one has Threshold and Sensitivity inputs which you can adjust to
specific zone sequentially. Motion Detection function can support to FTP, SMTP
and Alarm output for capturing and sending images or starting alarm output.
 Threshold: It means the extent which the alarm will be triggered.
 Sensitivity: It means that how often the sensor will scan the image different.
The higher sensitivity it is and the more frequently it scans.
Motion
Detection 1: Click it on for using Motion Detection 1 function
as a sensor. You can adjust and move the detecting zone by using mouse.
Motion
Detection 2: Click it on for using Motion Detection 2 function
as a sensor. You can adjust and move the detecting zone by using mouse.
Motion
Detection 3: Click it on for using Motion Detection 3 function
as a sensor. You can adjust and move the detecting zone by using mouse.
62
F531E & F731E User Manual
8.9. SYSTEM LOG
The System Log function allows users to review any changes and events happened.
The system starts logging automatically after started.

Enable remote log: Enables user to send the log data to a specified log server.
63
F531E & F731E User Manual
APPENDIX
A. FRAME-RATE AND BITRATE TABLE
Help to set IPCamera with your network environment to access Internet.
Base on your network UPLOAD environment to choose the suitable
Image-Quality setting. For example, if the network environment is ADSL
256Kb/s(upload) / 2Mb/s(download), the most fluent Image-Quality
needs to set up under 256 Kb situation.
A.1. MPEG4 @ 30fps / Kbps
Quality
640*480
320*240
160*120
Excellent
1000
300
90
Detailed
400
150
50
Good
300
100
30
Standard
250
70
25
Medium
250
55
20
A.2. MPEG4 / Kbps, fps
Image-Size
Bitrate Setting
Frame-Rate
Setting
Current Bitrate
Current
Frame-Rate
640*480
2048
30
1800
26
640*480
2048
15
2200
16
640*480
1536
30
1500
30
640*480
1536
15
1700
16
640*480
1024
30
1000
30
640*480
1024
15
1000
16
640*480
512
30
500
30
640*480
512
15
600
16
320*240
1536
30
1500
30
320*240
1536
15
1600
16
320*240
1024
30
1000
30
320*240
1024
15
1000
16
320*240
512
30
550
30
64
F531E & F731E User Manual
320*240
512
15
600
16
160*120
1024
30
950
30
160*120
1024
15
750
16
160*120
512
30
500
30
160*120
512
15
50
16
160*120
128
30
130
30
160*120
128
15
140
16
A.3. MJPEG @ 15fps / Kbps
Quality
640*480
320*240
160*120
Excellent
4000
1500
600
Detailed
2400
900
400
Good
1600
650
300
Standard
1300
500
240
Medium
900
350
170
A.4. MJPEG / Kbps, fps
Image-Size
Quality
Setting
Frame-Rate
Setting
Current Bitrate
Current
Frame-Rate
640*480
Excellent
15
4000
13
640*480
Excellent
5
1600
5
640*480
Good
15
1600
13
640*480
Good
5
650
5
640*480
Medium
15
900
14
640*480
Medium
5
360
5
320*240
Excellent
15
1500
13
320*240
Excellent
5
550
5
320*240
Good
15
650
13
320*240
Good
5
260
5
320*240
Medium
15
350
13
160*120
Medium
5
130
5
160*120
Excellent
15
600
13
160*120
Excellent
5
230
5
160*120
Good
15
300
13
160*120
Good
5
115
5
160*120
Medium
15
170
13
160*120
Medium
5
65
5
65
F531E & F731E User Manual
B. STORAGE REQUIREMENT TABLE
Help to set Recording Storage System. Please refer to the following table
to find out the capability for recording into your hard disk.
B.1. MPEG4 Storage Requirement GB / channel / day @ 30fps
Quality
640*480
320*240
160*120
Excellent
10.5
3.2
0.9
Detailed
4.2
1.6
0.5
Good
3.2
1.1
0.3
Standard
2.6
0.7
0.3
Medium
2.6
0.6
0.2
B.2. MPEG4 Storage Requirement GB / channel / day @ 15fps
Quality
640*480
320*240
160*120
Excellent
5.3
1.6
0.4
Detailed
2.1
0.8
0.3
Good
1.6
0.6
0.2
Standard
1.3
0.4
0.1
Medium
1.3
0.3
0.1
B.3. MPEG4 Storage Requirement GB / channel / day
Image-Size
Bitrate Setting
Frame-Rate Setting
Current Bitrate
640*480
2048
30
23.0
640*480
2048
15
22.2
640*480
1536
30
18.5
640*480
1536
15
17.9
640*480
1024
30
10.5
640*480
1024
15
10.5
640*480
512
30
5.3
640*480
512
15
6.3
320*240
1536
30
15.8
320*240
1536
15
16.9
320*240
1024
30
10.5
320*240
1024
15
10.5
320*240
512
30
5.8
66
F531E & F731E User Manual
320*240
512
15
6.3
160*120
1024
30
10.0
160*120
1024
15
7.9
160*120
512
30
5.3
160*120
512
15
0.5
160*120
128
30
1.4
160*120
128
15
1.5
B.4. MJPEG Storage Requirement GB / channel / day @ 15fps
Quality
640*480
320*240
160*120
Excellent
42.2
15.8
6.3
Detailed
25.3
9.5
4.2
Good
16.9
6.9
3.2
Standard
13.7
5.3
2.5
Medium
9.5
3.7
1.8
B.5. MJPEG Storage Requirement GB / channel / day
Image-Size
Quality Setting
Frame-Rate Setting
Current Bitrate
640*480
Excellent
15
42.2
640*480
Excellent
5
16.9
640*480
Good
15
16.9
640*480
Good
5
6.9
640*480
Medium
15
9.5
640*480
Medium
5
3.8
320*240
Excellent
15
15.8
320*240
Excellent
5
5.8
320*240
Good
15
6.9
320*240
Good
5
2.7
320*240
Medium
15
3.7
160*120
Medium
5
1.4
160*120
Excellent
15
6.3
160*120
Excellent
5
2.4
160*120
Good
15
3.2
160*120
Good
5
1.2
160*120
Medium
15
1.8
160*120
Medium
5
0.7
67
F531E & F731E User Manual
C. TESTING SYSTEM SPECIFICATION
Software:
MainConsole Version 2.6.4 Professional
CPU:
AMD Athlon 64*2 @3600+MHz
Memory:
2048 MB (2 x 1024 DDR2-SDRAM )
Ethernet:
VIA Rhine II Fast Ethernet Adapter
Hard Disk:
ST3250620A (250 GB)
Graphic card:
ATI Technologies Inc EAX1600 Series
Operating System:
Windows XP Professional SP2 x64
D. D1 PERFORMANCE OF 16 CHANNEL IP
CAMERA
Results from Test with a Resolution of 704×480 CCD IPCamera
704x480
Quality
Frame Rate
CPU Load
Bandwidth
16 IP camera
Excellent
30
95%
15~20 Mbps
Results from Test with a Resolution of 640×480 CMOS IPCamera
640x480
Quality
Frame Rate
CPU Load
Bandwidth
16 IP camera
Excellent
30
95%
10~15 Mbps
68
F531E & F731E User Manual
EUROPE – EU DECLARATION OF CONFORMITY
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC. The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the R&TTE Directive
1999/5/EC:
Clause
Description
EN 60950-1: 2001
Safety of Information Technology Equipment
EN 50392: 2004
Generic standard to demonstrate the compliance of electronic and electrical
apparatus with the basic restrictions related to human exposure to
electromagnetic fields (0 Hz - 300 GHz)
EN 300 328 V1.6.1 (2004-11)
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband
transmission systems; Data transmission equipment operating in the 2,4 GHz
ISM band and using wide band modulation techniques; Harmonized EN
covering essential requirements under article 3.2 of the R&TTE Directive
EN 301 489-17 V1.2.1
Electromagnetic compatibility and Radio spectrum Matters (ERM);
(2002-08) and EN 301 489-1
ElectroMagnetic Compatibility (EMC) standard for radio equipment and
V1.5.1 (2004-11)
services; Part 17: Specific conditions for 2,4 GHz wideband transmission
systems and 5 GHz high performance RLAN equipment
This device is a 2.4 GHz wideband transmission system (transceiver), intended for use
in all EU member states and EFTA countries, except in France and Italy where
restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in
order to obtain authorization to use the device for setting up outdoor radio links and/or
for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some
areas the RF output power may be limited to 10 mW EIRP in the frequency range of
2454 – 2483.5 MHz. For detailed information the end-user should contact the national
spectrum authority in France.
69
F531E & F731E User Manual
FEDERAL COMMUNICATION COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is
firmware-limited to channels 1 through 11.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
70
F531E & F731E User Manual
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
71