Samsung SCP-2250(P) User manual

Smart Dome Camera
User Manual
Z6806125901A-SCP-2250(P)-ENGLISH1 1
SCP-2250(P)
2010-07-21 오후 6:03:
overview
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of
electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this unit.
WARNING
 To reduce the risk of fire or electric shock, do not expose this appliance to rain or
moisture.
 To prevent injury, this apparatus must be securely attached to the floor/wall in
accordance with the installation instructions.
 Use only the 24V, 60Hz AC adaptor for power supply.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the
product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion,
fire, electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may
cause abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may
cause fire.
_ overview
Z6806125901A-SCP-2250(P)-ENGLISH2 2
2010-07-21 오후 6:03:
5. When installing the camera, fasten it securely and firmly. The fall of camera may
cause personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or
containers filled with water on top of the camera. Doing so may cause personal
injury due to fire, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire
or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way. (SAMSUNG is not liable for
problems caused by unauthorized modifications or attempted repair.)
● overview
8. If any unusual smells or smoke come from the unit, stop using the product. In such
case, immediately disconnect the power source and contact the service center.
Continued use in such a condition may cause fire or electric shock.
10. When cleaning, do not spray water directly onto parts of the product. Doing so may
cause fire or electric shock
11. Do not expose the product to the direct airflow from an air conditioner.
Otherwise, it may cause moisture condensation inside the Clear Dome due to
temperature difference between internal and external of the dome camera.
12. If you install this product in a low-temp area such as inside a cold store, you must
seal up the wiring pipe with silicon, so that the external air can not flow inside the
housing.
Otherwise, external high, humid air may flow inside the housing, pooling moisture
or vapor inside the product due to a difference between internal and external
temperature.
Z6806125901A-SCP-2250(P)-ENGLISH3 3
English _
2010-07-21 오후 6:03:
overview
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a
location subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature
(below -10°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power
and then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting
to do so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as
this may damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with
liquids, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at
any time.
10. When using the camera outdoors, moisture may occur inside the camera due
to temperature difference between indoors and outdoors. For this reason, it is
recommended to install the camera indoors. For outdoor use, use the camera with
built-in fan and heater.
_ overview
Z6806125901A-SCP-2250(P)-ENGLISH4 4
2010-07-21 오후 6:03:
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
● overview
CAUTION
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
Z6806125901A-SCP-2250(P)-ENGLISH5 5
English _
2010-07-21 오후 6:03:
overview
important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third prong
is provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as powersupply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has
been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
_ overview
Z6806125901A-SCP-2250(P)-ENGLISH6 6
2010-07-21 오후 6:03:
contents
Overview
Important Safety Instructions
Contents
Features
What’s Included
At a Glance
Installation &
Connection
10
10
14
17
Preparing Installation
Installation
Initial Setup
Connecting with Other Device
Setup
20
21
22
24
33
35
36
38
42
43
45
45
47
48
How to use the Keyboard
Controller
Main Menu
Profile
Camera Set
Intelligent Video
Privacy Zone
Preset
Auto Set
Zone Set
Alarm Set
Clock Set
Other Set
Communication
System Info
49
50
52
Shortcut Keys
Specifications
Product Appearance
2
Z6806125901A-SCP-2250(P)-ENGLISH7 7
10
20
Appendix
49
● overview
6
7
8
8
9
English _
2010-07-21 오후 6:03:
overview
Features
 With the state-of-the-art digital signal processing technology, full digital image
processing and special algorithm of 600-line high resolution implemented
 High performance surveillance camera, equipped with x25 zoom lens and digital
zoom IC, enabling monitoring up to 400 times
 DAY/NIGHT to improve the sensitivity by automatic conversion into the black and
white mode at night or in the environment with low illumination
 White Balance to control the brightness to the illumination
 Backlight Compensation under spotlight or utmost bright illumination
 Auto Focus to automatically adjust the focus to the subject movement
 Privacy zone to hide a specific area for personal privacy
 PAN/TILT for precise control at high speed
What’s Included
SW602
SW602
SW602
Please check if your camera and accessories are all included in the product package.
Camera
Frame Set
Cover
Template
Connectors
User Manual
User Manual
_ overview
Z6806125901A-SCP-2250(P)-ENGLISH8 8
2010-07-21 오후 6:03:
At a Glance
CAMERA
● overview
HOOK
HOOK
LENS
FRAME SET
RS-485
ALARM IN
POWER
INPUT
ALARM OUT
M
 Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you
have applied ethanol.
Z6806125901A-SCP-2250(P)-ENGLISH9 9
English _
2010-07-21 오후 6:03:
installation & connection
Preparing Installation
 Use the ceiling installation template when you install the camera on the ceiling on
your own.
 Run the cables through the “” shaped hole on the center of the template, and
remove films on the adhesives, and then attach the template on the desired location
on the ceiling.
 When installing the frames set, align all template’s screw holes and those of the
frames set.
 This template prevents dust entering from the ceiling into the camera assembly.
<TEMPLATE>
CEILING
CABLES
CEILING
TEMPLATE
CABLES
Installation
1. Press the “SNAP FIT” on the “ADAPTOR” to open the “ADAPTOR”, and arrange
cables so they pass out of the “FRAME SET”.
FRAME SET
FRAME SET
ADAPTOR
ADAPTOR
EXTERNAL
CABLES
SNAP FIT
SNAP FIT
10_ installation & connection
Z6806125901A-SCP-2250(P)-ENGLISH10 10
2010-07-21 오후 6:03:
2. Use the three “SCREWS” to fix the “FRAME SET” on a “CAMERA” installation
position.
FRAME SET
SCREW
ADAPTOR
SCREW
<Fixing Hole Diagram>
3. Connect external cables to the “CONNECTORS(ALARM IN, POWER, RS-485,
ALARM OUT)”and connect the “CONNECTOR” to the “ADAPTOR”.
Insert the cable into the “FRAME SET”, and close the “ADAPTOR”.
● installation & connection
SCREW
FRAME SET
POWER INPUT ALARM OUT
ALARM IN
ADAPTOR
RS-485
SNAP FIT
BNC JACK
INSULATION TUBE
M
 Then, wrap the “BNC JACK” with the “INSULATION TUBE”, and use an insulation
tape to seal up the end of the “INSULATION TUBE” so that the “BNC JACK” does
not protrude outside of the “INSULATION TUBE” coating.
For more information about cable connection, refer to “Connecting the adaptor
cable”. (page 19)
Z6806125901A-SCP-2250(P)-ENGLISH11 11
English _11
2010-07-21 오후 6:03:
installation & connection
4. Connect the “SAFETY WIRE” of the “CAMERA” to the “BRACKET WIRE” on the
“FRAME SET”. Arrange the “22P CONNECTOR” of the “CAMERA” in line with that
of the “ADAPTOR”, push the “HOOK” on either end of the “CAMERA” in the “RACK”
direction of the “FRAME SET” to secure the two.
Then, ensure that all of the two “HOOKS” “clicks” to fix to the “RACK” properly.
BRACKET WIRE
FRAME SET
SAFETY WIRE
22P CONNECTOR
CAMERA
FRAME SET
FRAME SET
RACK
RACK
CAMERA
CAMERA
HOOK
PROTECTIVE TAPE
HOOK
PROTECTIVE FILM
PROTECTIVE TAPE
M
 When the installation is completed, remove the “PROTECTIVE FILM” and
“PROTECTIVE TAPE” from on the lens.
12_ installation & connection
Z6806125901A-SCP-2250(P)-ENGLISH12 12
2010-07-21 오후 6:04:
5. Arrange the “COVER” arrow in line with the “FRAME SET” arrow, and push in the
“COVER”. Insert the “COVER” to the end, and turn the “COVER” clockwise.
As shown in the figure below, turn it until you see the “BUTTON” hole and hear a
click.
 Ensure that the “COVER” should not move any further if you turn the “COVER” counter
clockwise.
BUTTON
FRAME SET
● installation & connection
COVER
CAMERA
COVER
If you want to remove the “COVER”, hold down the “BUTTON” and turn the
“COVER” counter clockwise to remove the “COVER”.
BUTTON
COVER
Z6806125901A-SCP-2250(P)-ENGLISH13 13
English _13
2010-07-21 오후 6:04:
installation & connection
Initial Setup
Camera Address Setup
Use SW606, SW605, and SW604 to specify the camera address.
You can specify between 0 and 255 for the address, where the hundreds digit is
with SW606, the tens digit with SW605, and the ones digit with SW604.
ex) Camera address: If the address is 1, follow the steps in the figure below.
SW606
(x100)
SW605
(x10)
SW604
(x1)
Communication Protocol Setup
Use pins #1~#4 of SW603 to specify the communication protocol.
PIN
Comp
A
B
C
D
E
----H
I
J
------N
O
P
Q
R
PIN1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
PIN2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
PIN3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
PIN4
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
ON
ON
ON
ON
ON
OFF
OFF
PIN7
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
A : SAMSUNG HALF
B : SAMSUNG FULL
<Bottom of the camera holder>
14_ installation & connection
Z6806125901A-SCP-2250(P)-ENGLISH14 14
2010-07-21 오후 6:04:
Baud Rate Setup
Use pins #5, #6 of SW603 to set the baud rate.
PIN 5
PIN 6
4800 BPS
ON
ON
9600 BPS
OFF
ON
19200 BPS
ON
OFF
38400 BPS
OFF
OFF
● installation & connection
BAUD RATE
The factory default is 9600 BPS.
Setting RS-422A/RS-485 Termination
As it is shown in the structure map, when Controller and RS-422A/RS-485 is
connected, it should be terminated according to the Cable feature of impedance
on the each end of the transmitting line to transfer the signals in long distance by
controlling the reflection of the signals to the lowest.
n < 32
Termination
Controller
TX+(DATA+)
TX-(DATA-)
RX+
RX-
CAM 1
RX+
RX-
CAM 2
RX+
RX-
CAM n-1
RX-
Termination
SW1-ON
RX+
CAM n
<RS-485 Half Duplex Organization>
Termination : Using numbers 1 and 2 PIN, turn to <ON> and it will be terminated.
Z6806125901A-SCP-2250(P)-ENGLISH15 15
English _15
2010-07-21 오후 6:04:
installation & connection
n < 32
Termination
SW1-ON
SW2-ON
Controller
Termination
CAM 1
CAM 2
CAM n-1
CAM n
<RS-422A/RS-485 Full Duplex Organization>
M
 A communication error may occur if you connect multiple cameras that are assigned
the same address in the network.
16_ installation & connection
Z6806125901A-SCP-2250(P)-ENGLISH16 16
2010-07-21 오후 6:04:
Connecting WITH OTHER device
MONITOR
POWER SOURCE
ALARM OUT
● installation & connection
CONTROLLER/DVR
ALARM IN
Connecting to a monitor
1. Connect one end of the BNC
video cable connector to the
Video Output Terminal (VIDEO
OUT).
2. Connect the other end of the
connector to the Video Input
Terminal of the monitor.
Z6806125901A-SCP-2250(P)-ENGLISH17 17
Video terminal on the
rear of monitor
BNC Cable
English _17
2010-07-21 오후 6:04:
installation & connection
To connect ALARM IN
1. Connect one end of the external device's signal line to a corresponding ALARM
IN port of the monitor.
2. Connect the other end of the signal line to the earth-grounding [GND] port.
To connect ALARM OUT
1. Connect one end of the external device's signal line to a corresponding ALARM
OUT port of the monitor.
2. Connect the other end of the signal line to the common [COM] port.
To connect the controller
Connect an external controller or DVR to the camera, with which you can adjust the
camera.
1. Connect the Rx+ pin of the
camera to the Tx+ pin of the
controller.
2. Connect the Rx- pin of the
camera to the Tx- pin of the
controller.
Rx
Tx
3. Connect the Tx+ pin of the
camera to the Rx+ pin of the
controller.
4. Connect the Tx- pin of the
camera to the Rx- pin of the
controller.
18_ installation & connection
Z6806125901A-SCP-2250(P)-ENGLISH18 18
2010-07-21 오후 6:04:
Connecting the adaptor cable
Adaptor Board
● installation & connection
Power Supply
Connect the cables as necessary, and turn on the camera to check if it works
properly.
1. Connect the adaptor to the power terminal of the camera.
2. Plug the power cord of the adaptor into the wall outlet.
Z6806125901A-SCP-2250(P)-ENGLISH19 19
English _19
2010-07-21 오후 6:04:
setup
Connect the camera to the keyboard controller or DVR, with which you
can manipulate and change the settings of the camera.
How to use the keyboard controller
Follow the steps below to set the camera menu using the controller.
1. Open the Camera Setup screen.
2. Use the joystick to navigate through the menus.
3. Press [ENTER] to select a menu item.
4. Use the joystick to change the value of the selected item.
5. Press [ENTER] to apply your changes.
Using OSD icons
 _+: If these icons appear in the left and right corner of a menu item, you can use
the joystick to move to the previous or next menu.

(EXIT): Exits the menu setup screen.
Before exiting the setup screen, select <SAVE> to save your settings
to the whole menus, or <QUIT> to cancel them.



(RET): Saves your settings and returns to the previous screen.
(HOME): Returns to the main menu.
(SAVE): Use this icon if you want to save your settings after you specified the
mask area and privacy area, etc.
Once you saved your settings, the changes remain intact even if you
select <QUIT> on exit.

(DEL): Use this icon if you want to delete a mask, or privacy area, etc.
Once you deleted your settings, the deletions remain valid even if you
select <QUIT> on exit.

: This icon appears in the right of a menu containing sub menu items.
M
 While any operation of PRESET, AUTO PAN, SCAN, and PATTERN is running, and if
the camera is turned off and back on without any particular manipulation, the
camera will resume the last run operation.
 You can set the menu item only if the tilt angle is within 90°.
If you enter the menu setup screen with the camera positioned out of a tilt of 90°,
the camera will rotate by 180° to fall into the opposite position within a tilt of 90°.
20_ setup
Z6806125901A-SCP-2250(P)-ENGLISH20 20
2010-07-21 오후 6:04:
Main Menu
This is the first screen you ever see when you turn on the camera where you can set the
camera environment to your needs.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
Z6806125901A-SCP-2250(P)-ENGLISH21 21
● setup
 PROFILE
 MAIN MENU 
Select a mode appropriate to the camera
PROFILE
installation environment.
CAMERA SET
INTELLIGENCE
 CAMERA SET
PRIVACY ZONE
PRESET
You can configure the camera settings.
AUTO SET
 INTELLIGENCE
ZONE SET
ALARM SET
Offers motion detection and tracking
CLOCK SET
functions.
OTHER SET
 PRIVACY ZONE
You can configure the privacy settings.
 PRESET
You can set the PRESET POSITION and
COMMUNICATION
DURATION.
SYSTEM INFO
 AUTO SET
Contains sub menu items of AUTO PAN,
PATTERN, SCAN and AUTO PLAY.
 ZONE SET
You can set the standard azimuth and
zone area for the camera.
 ALARM SET
You can set the alarm priority and I/O sequence.
 CLOCK SET
You can set the display time and format.
 OTHER SET
You can set preferred language, reset the system, and select an OSD color to
your preference.
 COMMUNICATION
Configures the settings pertaining to RS-485 communication.
 SYSTEM INFO
Shows the system information such as the camera version or communication
settings.
English _21
2010-07-21 오후 6:04:
setup
PROFILE
You can select one from the pre-determined configurations as appropriate to your
specific camera installation environment.
Your selection on each item in PROFILE will affect all other settings of the camera.
 STANDARD
 PROFILE 
Automatically optimizes the camera settings
STANDARD
to the normal environment.
ITS
 ITS
BACKLIGHT
DAY/NIGHT
This setting enables you to analyze the traffic
GAMING
situation and take the traffic information at a
CUSTOM
glance.
 BACKLIGHT
This setting enables you to view a sharp
background and object even in a severe
backlight scene.
 DAY/NIGHT
Automatically optimizes the camera settings to the day and night scene.
 GAMING
This automatically configures the settings so that you can work in a stable illumination condition as indoors.
 CUSTOM
Your change to any of the PROFILE settings will switch the display to CUSTOM.
CAMERA SETUP MENU
Parent Menu Sub-menus
IRIS
ALC
LEVEL
STANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
ALC
ALC
ALC
ALC
ALC
-
-
-
-
-
0
0
0
0
0
OFF
OFF
OFF
BLC
OFF
MOTION
(F.FAST)
---
(F.FAST)
---
NORM
(F.FAST)
---
SLOW
DNR
MEDIUM
MEDIUM
MEDIUM
MEDIUM
MEDIUM
BACKLIGHT
SHUTTER
(OFF)---
(OFF)---
(OFF)---
(OFF)---
(OFF)---
SENSE UP
AUTO X4
AUTO X2
AUTO X4
AUTO X4
AUTO X4
22_ setup
Z6806125901A-SCP-2250(P)-ENGLISH22 22
2010-07-21 오후 6:04:
CAMERA SETUP MENU
Parent Menu Sub-menus
XDR
STANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
MEDIUM
MEDIUM
MEDIUM
MEDIUM
MEDIUM
AUTO
AUTO
DAY
AUTO
DAY
NIGHT
BURST
EXT
BURST
DAY
-
-
-
-
ON
OFF
OFF
OFF
-
-
-
-
-
OFF
ON
OFF
OFF
OFF
DAY
DAY/NIGHT
DAY
DAY/NIGHT
DAY
-
-
-
-
-
ATW2
ATW1
ATW1
ATW1
ATW1
RED
0
0
0
0
0
BLUE
0
0
0
0
0
MODE
WHITE BAL
OFF
-
-
-
-
-
MEDIUM
Custom Setting
MEDIUM
Custom Setting
ATW2
OFF
ATW2
OFF
RED Custom Setting
0
Custom Setting
0
Custom Setting
BLUE Custom Setting
0
Custom Setting
0
Custom Setting
2
2
2
2
NIGHT
BRIGHTNESS Custom Setting
MODE
DETAIL
Z6806125901A-SCP-2250(P)-ENGLISH23 23
OFF
2
● setup
DAY/NIGHT
English _23
2010-07-21 오후 6:04:
setup
CAMERA SET
You can configure the general settings of the camera module.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU> - <CAMERA SET>.
The Camera Setup menu appears.
2. Change the settings as necessary, or select
an item to check.

CAMERA SET
CAMERA ID
IRIS
MOTION
DNR
SHUTTER
SENS-UP
FLICKERLESS
XDR

OFF
ALC
(F.FAST) --MID
(OFF) --AUTO X4
OFF
MID
CAMERA ID
Provide the ID and location for a camera that displays on the screen.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <CAMERA SET> - <CAMERA ID>.
2. Use the joystick to select a desired character,
then press [ENTER].
In the lower input box of the screen, the
selected character will be entered.
 You can enter up to 54 characters including
alphabets, numbers and special characters.
 LOCATION : Specify the display position
of the camera ID.
CAMERA ID
ABCDEFGHIJKLMNOPQRSTUVWXYZO
123456789 : ?_+()/
SP SP
LOCATION
-----------------------------------------------------------------
3. When done, press [ENTER].
The camera ID will be displayed in the specified position.
24_ setup
Z6806125901A-SCP-2250(P)-ENGLISH24 24
2010-07-21 오후 6:04:
IRIS
The IRIS menu is useful if you set to adjust the
intensity of radiation incoming to the camera.
 MANUAL : Adjust the iris level manually.
M
 The overall brightness target of a camera
[ 00] ----I----
BACKLIGHT
AREA
<SIZE> <LOCATION> BLC
USER
● setup
 ALC : Adjust the open and close of the iris.
- LEVEL : Select an overall brightness level.
- BLC : With <BACKLIGHT> set to
<BLC>, you can specify the BLC area.
With AREA set to <USER>, you can
specify the position and size.
ALC
LEVEL
MANUAL
LEVEL
[ 00] ----I----
will be set to ALC level 0, while the iris
can be adjusted manually.
AGC
With this, you can adjust the AGC level of a
 CAMERA SET 
camera.
With AGC active, if the signal strength falls
CAMERA ID
OFF
IRIS
ALC
below the standard level, AGC will amplify the
AGC
(VERY HIGH) --video signal to automatically improve the
DNR
MID
sensitivity.
SHUTTER
OFF
If <SENS-UP> is set to <OFF>, or <FIX>
SENS-UP
OFF
FLICKERLESS
OFF
mode, the <MOTION> menu will switch to
XDR
MID
<AGC>.
With the USER ( ) submenu selected, press
[ENTER] to display the corresponding screen.
In this mode, you can select from VERY LOW
to VERY HIGH in 16 levels, enabling deeper, wider choices to your convenience.
With the FIX ( ) submenu selected, press [ENTER] to display the corresponding
screen. In this mode, you can select an individualized mode in 16 levels, regardless of
the brightness.
Z6806125901A-SCP-2250(P)-ENGLISH25 25
English _25
2010-07-21 오후 6:04:
setup
M
 As long as the DAY/NIGHT menu is set to AUTO in Camera Setup, the AGC menu is
not available.
 As long as FLICKERLESS is set to ON, the FIX mode is not available.
MOTION
You can specify a level of AGC for controlling the camera motion.
This is available only of the SENSE UP menu is set to AUTO.
Select F.FAST if you want to monitor a very fast moving object in a low contrast
scene, and S.SLOW if monitoring a very slow moving, inanimate object in the same
condition.
 As long as DAY/NIGHT is set to <AUTO>, the <MOTION> menu is not available.
DNR
Reduces the noise on the camera image.
The higher the level is, the greater the effect is.
Set it to <USER> to specify the level.
SHUTTER
You can select a fixed fast electronic shutter
speed in 7 options ranging from 1/100 to 1/10k,
which is mostly used to take a picture of a fast
moving object.
 As long as SENSE UP is set to AUTO, FIXED /
FLICKERLESS to ON, the SHUTTER menu is not
available.

CAMERA SET
CAMERA ID
IRIS
AGC
DNR
SHUTTER
SENS-UP
FLICKERLESS
XDR

OFF
ALC
(VERY HIGH) --MID
1/100
(OFF) --(OFF) --MID
SENS-UP
Automatically senses the darkness level at night or in a low contrast scene, and
extends the accumulation time accordingly; you can select <AUTO> or <FIX> for a
bright and sharp image.
M
 If the SHUTTER menu is set to fixed electronic shutter mode, the SENSE UP menu
will not be available.
 As long as the FLICKERLESS is set to ON, you cannot set the SENS-UP FIX.
26_ setup
Z6806125901A-SCP-2250(P)-ENGLISH26 26
2010-07-21 오후 6:04:
FLICKERLESS
This will prevent possible screen distortion due to a mismatch between the vertical
sync frequency and the blinking frequency of the lighting; if set to <ON>, the shutter
speed will be fixed to 1/100 second.
 If SHUTTER is set to FIX, SENSE UP to FIX, and AGC to FIX, the <FLICKERLESS> menu is
not available.
This will correct a brightness difference between different scenes for the optimal
visibility by calculating the ambient luminance contrast in a certain unit of pixels.
The higher the value is, the higher the correction level is.
● setup
XDR
DAY/NIGHT
You can specify a recording mode according to the scene.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <CAMERA SET> - <DAY/NIGHT>.
2. Select a screen transition mode according
DAY/NIGHT
AUTO
WHITE BAL
to the illumination, and set options as
FOCUS MODE
ONEAF
appropriate.
ZOOM SPEED
[2]
 DAY : Fixed to DAY mode, regardless of
DISPLAY ZOOM
OFF
DISPLAY P/T
OFF
the scene.
DIGITAL ZOOM
OFF
 NIGHT : Fixed to NIGHT mode,
DETAIL
[2]
regardless of the scene.
V-SYNC
INT
If BURST is set to <ON>, the burst
signal will be output along with the
black-and-white composite video signal.
 AUTO : According to the luminance, this
AUTO
will switch DAY to NIGHT mode, or vice
versa.
BURST
OFF
DAYNIGHT
- BURST : If set to <OFF>, the burst
BRIGHTNESS
MID
signal will not be output in NIGHT mode.
DWELL TIME
2SEC
NIGHTDAY
- DAYNIGHT BRIGHTNESS : Specify
BRIGHTNESS
MID
the brightness level switching from
DWELL TIME
5SEC
COLOR to BW filter.
MASK AREA
1 2
Adjusting from HIGH to LOW will cause
to switch the filter in a darker screen.
- DAYNIGHT DWELL TIME : Time
required to determine the filter switch.
- NIGHTDAY BRIGHTNESS : Specify the brightness level switching from
BW to COLOR filter. Adjusting from HIGH to LOW will cause to switch the
filter in a darker screen.
Z6806125901A-SCP-2250(P)-ENGLISH27 27
English _27
2010-07-21 오후 6:04:
setup
- NIGHTDAY DWELL TIME : Time required to determine the filter switch.
- MASK AREA : If there exists a bright
MASK AREA
spot light source in a night scene, you
<SIZE>
can specify the size and position as
<LOCATION>
needed.
This will prevent an error in switching
filter, or failure to determine the filter
switch in a night scene where a bright
spot light source exists.
Any excessively bright area in a night
scene will be MASKed.
 You can specify MASK 1 and 2
simultaneously.
 If <BACKLIGHT> is set to <BLC>, the MASK AREA function is not available.
 EXT : The interface to an external alarm enables an automatic switch between
DAY and NIGHT mode.
If you set <DAY/NIGHT> to EXT, and alarm #1 to NO/NC in ALARM SETALARM IN SET, the alarm can be used for an input signal in EXT mode of
<DAY/NIGHT>.
If an alarm signal occurs, the mode will switch to NIGHT.
M
 If <DAY/NIGHT> is set to EXT, ALARM1 in ALARM OUT SET, and ALARM1 in ALARM
SET-AUTO SET are not available.
 If you use an infrared light source while in AUTO mode, this may cause a failure in
AUTO SWITCH or AUTO FOCUS.
28_ setup
Z6806125901A-SCP-2250(P)-ENGLISH28 28
2010-07-21 오후 6:04:
WHITE BAL
If you need to adjust the color according to the ambient illumination, you can use
the <WHITE BAL> function.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
Illumination is generally referred to as color temperature, which is represented in a
measurement of kelvin (K). Color temperatures for ordinary lighting are as follows:
- ATW1,2 : If you set the <WHITE
BAL> menu to <ATW1> or
<ATW2> mode, this will monitor
the change of the color temperature
to correct the <WHITE BAL> as
needed.
The following color temperature
ranges are assured in individual
modes:
ATW1 : 2500K ~ 9300K (1)
ATW2 : 2000K ~ 10000K
(suitable to sodium light source) (2)
10000K
Blue sky
● setup
In the <WHITE BAL> menu, you
can set a mode for correcting the
<WHITE BAL>.
Rainy
9000K
8000K
7000K
6000K
Cloudy
5000K
4000K
Partly Cloudy
Sunny
Fluorescent lamp
3000K
2000K
1000K
Halogen lamp
Candlelight
Tungsten lamp
1 : With <ATW1> mode active in a color temperature environment ranging
beyond between 2500K and 9300K, a proper white balance value may not be
produced; if this is the case, you are recommended to use <ATW2> mode.
2 : With <ATW2> mode active in a mostly single color environment, the display
color and the actual one may differ; so select a mode as appropriate to your
color temperature environment.
Z6806125901A-SCP-2250(P)-ENGLISH29 29
English _29
2010-07-21 오후 6:04:
setup
1. Select <CAMERA SET> - <WHITE BAL>.
2. Select a mode where you set the <WHITE BAL>.
 DAY : You can set the RED, and BLUE
value in DAY mode.
The screen will be displayed in colors
DAY/NIGHT
according to your settings.
MODE
 You can set the R-GAIN, and B-GAIN value
only in <AWC> mode.
 If AGC is set to <OFF> or <FIX>, the NIGHT
WHITE BAL
DAY
AWC
[ 00] ---- I ---[ 00] ---- I ----
RED
BLUE
R-GAIN
B-GAIN
[0064]
[0064]
menu can not be accessed.
 NIGHT : You can set the <WHITE BAL>
according to the ambient illumination.
If NIGHT mode is set to <OFF>, the
<WHITE BAL> will operate in a mode
specified in DAY mode at all times;
otherwise, the screen will switch to a
mode specified in <DAY/NIGHT>.
You can set the RED, BLUE and
BRIGHTNESS value in DAY mode.
The screen will be displayed in colors
according to your settings.
WHITE BAL
DAY/NIGHT
BRIGHTNESS
MODE
RED
BLUE
R-GAIN
B-GAIN
NIGHT
MID
AWC
[ 00] ---- I ---[ 00] ---- I ----
[0064]
[0064]
3. According to the specified recording mode, select a <WHITE BAL> mode with
necessary options.
 ATW1,2 : The camera can automatically adjust the color temperature in real
time, according to the ambient conditions.
(Color temperature range 1: 2500K ~ 9300K, 2 : 2000K ~ 10000K)
 AWC : Pressing [ENTER] on a desired item will perform ATW once.
 You can set the R-GAIN/B-GAIN value.
 3200K : Set the color temperature to 3200K.
 5600K : Set the color temperature to 5600K.
- BRIGHTNESS : Specify a brightness level switching from DAY mode to
NIGHT mode setting.
- RED : Adjust the strength of the red color.
- BLUE : Adjust the strength of the blue color.
- R-GAIN/B-GAIN : Specify the current color temperature manually.
30_ setup
Z6806125901A-SCP-2250(P)-ENGLISH30 30
2010-07-21 오후 6:04:
FOCUS MODE
You can select a focus mode according to the
angle that you adjusted for camera recording.
- AF : This will monitor the screen continuously
to focus automatically. If you adjust the focus
manually, that will operate the same as in
<MF>. This will also restore focus after the
operation of pan/tile/zoom.
AUTO
AF
[2]
[2]
OFF
OFF
X16
INT
● setup
- SENSITIVITY : Indicates the sensitivity of auto
focus, which you can adjust between level 1
and level 7.
The closer your setting is to 7, the more
sensitively the auto focus function performs.
The Night setting is used when a strong light
reflects in a low contrast scene.
You can set it to OFF, LOW, MEDIUM, or
HIGH; set it to <HIGH> when there exist a
strong light such as street light.
DAY/NIGHT
WHITE BAL
FOCUS MODE
ZOOM SPEED
DISPLAY ZOOM
DISPLAY P/T
DIGITAL ZOOM
DETAIL
V-SYNC
AF
SENSITIVITY
NIGHT
[5]
MID
- ONEAF : Restores focus after the operation
of pan/tile/zoom, and operates the same as
in <MF> unless the operation of pan/tile/
zoom is executed.
- MF : You can adjust the focus manually.
M
 While you are working on the following objects, <AF> may not work properly.
If this is the case, use <MF> instead.
- Very bright object, or dominant object in a dark scene
- Object against the rear side of a moist or dirty glass
- A scene where nearby and distant objects co-exist
- White wall or single-colored object
- Venetian blinds and other horizontally striped objects
ZOOM SPEED
You can adjust the zoom operation speed.
DISPLAY ZOOM
You can set to display the zoom status on the screen.
 It will disappear in about 3 seconds if the zoom factor has no further change.
Z6806125901A-SCP-2250(P)-ENGLISH31 31
English _31
2010-07-21 오후 6:04:
setup
DISPLAY P/T
You can set to display the operation status of pan/tilt when it is active.
 It will disappear in about 3 seconds if the pan/tilt position has no further change.
However, the allowable error is ±2°.
DIGITAL ZOOM
You can set the maximum allowable digital zoom ratio.
Digital Zoom will start operation after it is zoomed in to the maximum optical ratio of
x25. If you set DIGITAL ZOOM to x16, you can take a shot at up to x400 (25x16).
DETAIL
Used to adjust the vertical and horizontal distinction, respectively.
V-SYNC
You can set the V-SYNC mode.
- If you select <INT>, the camera will use the internal synchronization.
- If selecting <LINE>, the camera will use an external power frequency for
synchronization. The LL-PHASE can be adjusted as appropriate.
AGC COLOR SUP
You can adjust the color reproduction range
according to AGC.
REVERSE
You can reverse the video signal from left
to right, upside down, or vice versa to your
convenience.
AGC COLOR SUP
REVERSE
POSI/NEGA
PIP
DIS
MID
OFF
+
OFF
OFF
POSI/NEGA
You can set the video brightness signal to
normal or reverse.
PIP
You can view a main image with a sub image on the same screen.
32_ setup
Z6806125901A-SCP-2250(P)-ENGLISH32 32
2010-07-21 오후 6:04:
M
 If more than one PRIVACY ZONE is specified, and PRIVACY SET to <ON>, the PIP
function is not available.
 As long as SENSE UP is set to FIXED, PIP menu is not available.
 According to the luminance, PIP will disappear if the SENSE UP menu is set to AUTO.
DIS (Digital Image Stabilization)
M
 If you set <DIS> to <ON>, the image will be enlarged with digital zoom as much
area as compensated. (Approximately 1.2 times of the optical zoom factor)
If you set the digital zoom to a larger ratio than the actual enlargement for
compensation, the <DIS> function will be disabled.
● setup
If you set it to <ON> for a camera that is trembled or vibrated from an ambient
change, this will automatically compensate for the flicker on the screen.
 <DIS> may not work properly in the following images:
Single-colored flat image / Low contrast scene / High frequency image taken under
a fluorescent lamp / Regular-patterned image
Intelligent Video
You can enable the motion detection and tracking functions.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<INTELLIGENCE>.
2. Select each item and set appropriately.
MOTION
You can enable the motion detection and
tracking functions.
M

INTELLIGENCE
MOTION
ADVANCED
MASK AREA
DISPLAY
SENSITIVITY
RESOLUTION
ALARM OUT
1

OFF
OFF
3 4
ON
2
[4]
[3]
 If you set it to <DETECTION>, the
<FIXED/MOVED> option of ADVANCED
menu will not be available.
 In following situations, motion detection and tracking function may not work
properly.
- When there is sudden changes of brightness
- When the device moves
- When a certain object’s movement fills most of the framing area
- When there is difficulties in distinguishing the moving object and background
Z6806125901A-SCP-2250(P)-ENGLISH33 33
English _33
2010-07-21 오후 6:04:
setup
ADVANCED
You can detect motions and mark the video that contains such motion, and enables
tracking of the movement. (The auto PTZ function is not supported for tracking an object.)
Selecting the <FIXED/MOVED> option will mark a region if an existing object
disappears, or a new object appears and fixed for a certain period of time.
M
 In following situations, FIXED/MOVED detection may not work properly.
- When multiple motions continue arbitrarily.
- When the object that is fixed continues to move in the same position.
- When a newly appearing object conceals another object that is moving.
MASK AREA
1. Select the number of the area to be
masked that will be excluded from motion
detection.
2. Select the mask number and set the mask
size and its coverage.
MASK AREA
<SIZE>
<LOCATION>
DISPLAY
When selected <ON>, it displays the motion
detected and detection of configured
advanced function.
SENSITIVITY
Sets the sensitivity of motion sensor.
RESOLUTION
The bigger the resolution setting, the smaller the object that can be detected.
ALARM OUT
When selected <ON>, it outputs alarm
signal when the motion is detected and on a
detection of configured advanced function.
ALARM OUT
MOTION
FIXED/MOVED
ON
ON
34_ setup
Z6806125901A-SCP-2250(P)-ENGLISH34 34
2010-07-21 오후 6:04:
PRIVACY ZONE
You can set up to 12 privacy zones that will be hided for privacy of the subject when
recording.
Zone Setup
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
2. Select the number of the zone and press
[ENTER].
The Zone setup screen appears.
3. Select the <SET P/T/Z> and press
[ENTER].
Using the joystick, adjust the camera’s
pan, tilt and zoom.
4. Select the <PIXEL LEVEL>.
Select the pixel level for the SIZE and
LOCATION settings.
5. Select <POINT> and press [ENTER]. The
Privacy zone would be marked each time
you press [ENTER].

1
7
PRIVACY ZONE
2
8
3
9
4
10

5
11
PRIVACY SET
STYLE
6
12
● setup
1. Select <MAIN MENU>-<PRIVACY ZONE>.
ON
MOSAIC1
PRIVACY ZONE SET 1
<SET P/T/Z>
PIXEL LEVEL
<POINT>
[4]
6. Use the joystick to set the position of each
point (top left, top right, bottom right,
bottom left), and press [ENTER]. Position
setting is completed.
7. Save the changes and move to the previous screen and select the <STYLE>.
Select the <COLOR> and pick a desired color.
M
 Setting one or more privacy zone and enabling privacy function will disable the PIP
function.
 For better privacy protection, make your privacy zone bigger than the required,
bigger by about 30%.
 Video portion of mosaic pattern or colored by the privacy zone setup is not
recoverable.
Z6806125901A-SCP-2250(P)-ENGLISH35 35
English _35
2010-07-21 오후 6:04:
setup
PRESET
This function provides preset camera settings such as pan, tilt, zoom and focus so to
enable quicker and easier accessing and monitoring, which supports up to 512 presets.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<PRESET>.
 MAIN MENU 
PROFILE
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
PRESET
AUTO SET
ZONE SET
ALARM SET
CLOCK SET
OTHER SET
2. Select the preset number.
PRESET

0*
5
10
15
20
25
30
1
6
11
16
21
26
31
2
7
12
17
22
27

3. Select <POSITION> and adjust <PAN/
TILT/ZOOM> to the desired setup using
the joystick.
4. Set <PRESET ID> to <ON> and enter the
name.
 For entering the name, refer to “CAMERA ID”.
(page 24)
1/16

3
8
13
18
23
28
4
9
14
19
24
29

PRESET NO. 1
POSITION
PRESET ID
PRESET SPEED
DWELL TIME
IMAGE HOLD
CAMERA SET
[5]
ON
3SEC
OFF
ON
36_ setup
Z6806125901A-SCP-2250(P)-ENGLISH36 36
2010-07-21 오후 6:04:
5. Select <PRESET SPEED> and adjust the pan/tilt speed of the preset.
6. Set the <DWELL TIME> that defines the camera's hold duration and <IMAGE
HOLD> of the preset.
 If you set the <IMAGE HOLD> to <ON>, the video image will be held still until the
camera reaches the preset position.
 For details on setting <IRIS>, <WHITE BAL>
and <FOCUS MODE>, refer to “CAMERA
SET”. (pages 24 ~ 33)
M
CAMERA SET
IRIS
WHITE BAL
FOCUS MODE
ALC
MF
● setup
7. Set <CAMERA SET> to <ON>.
You can adjust camera setups for each
preset.
 The preset position can be specified for a
tilt range of between -6° and 90°.
Those presets that are out of a tilt of 90° can not be specified.
 If you try to specify a preset position for a range exceeding a tilt of 90° using a
controller (SSC-1000, 2000 or 5000), you will see a message of <SET AGAIN> on
the screen. If this is the case, try again for a range below a tilt of 90°.
 If you upload/download the menu setting using SSC-1000, 2000 or 5000, the
preset may differ from the menu setting so define the preset again after the
operation.
Z6806125901A-SCP-2250(P)-ENGLISH37 37
English _37
2010-07-21 오후 6:04:
setup
AUTO SET
You can set the AUTO PAN, PATTERN, and AUTO PLAY.
M
 If you upload/download the menu setting using SSC-1000, 2000 or 5000, the
settings for AUTO PAN, PATTERN, SCAN, and PRESET may differ from the menu
settings so define them again after the operation.
Auto Pan Setup
Set the starting and ending positions to patrol between points at specified speed.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<AUTO SET>.
 MAIN MENU 
PROFILE
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
PRESET
AUTO SET
ZONE SET
ALARM SET
CLOCK SET
OTHER SET
2. Select the number of <AUTO PAN>.
AUTO PAN setup screen appears.

AUTO SET
AUTO PAN
1
PATTERN
SCAN
1
AUTO PLAY

2 3 4
1* 2* 3*
2 3 4
OFF
38_ setup
Z6806125901A-SCP-2250(P)-ENGLISH38 38
2010-07-21 오후 6:04:
3. Select each item and set appropriately.
 POSITION : Set the starting and ending
positions for the <AUTO PAN>.
Move to the setting screen and adjust
pan/tilt to the desired starting position,
and then press [ENTER].
Again, adjust pan/tilt to the desired
ending position and press [ENTER] to
finish <AUTO PAN> setup.
AUTO PAN 1
POSITION
DIRECTION
ENDLESS
SPEED
DWELL TIME
[10]
LEFT
OFF
3SEC
<RIGHT>
<LEFT>
START
START
END
● setup
 DIRECTION : Sets the direction of the camera’s movement from the starting to
the end position. (Based on panning)
END
 ENDLESS : Instead of shuttling between start and end positions, the camera
turns 360° endlessly while stops for the <DWELL TIME> at both positions.
 SPEED : Sets the moving speed of the camera, from 1 to 64.
 DWELL TIME : Sets the dwell time at the starting and ending positions, from
1 to 60 seconds.
Pattern Setup
You can manually record your pan/tilt/zoom movements to a monitoring pattern for
up to 2 minutes.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<AUTO SET>.
2. Select the pattern number.
PATTERN setup screen appears.
3. Select the <POSITION> and set the
pattern's starting position and press
[ENTER].
Z6806125901A-SCP-2250(P)-ENGLISH39 39
PATTERN SET 1
<POSITION>
START
English _39
2010-07-21 오후 6:04:
setup
4. Select the <START> and move the
camera using pan/tilt/zoom.
5. Your manual camera actions will be
recorded for up to 2 minutes, and returns
to the previous menu automatically.
PATTERN SET 1
<POSITION>
START
 To stop manual recording and return to the
previous menu before 2 minutes, press
[ENTER].
Scan Setup
You can set the SCAN operation to include a defined preset position.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<AUTO SET>.
2. Select the scan number.
SCAN setup screen appears.
3. Move the cursor to a number with the []
mark which contains a defined preset.
4. Press [ENTER].
[S] mark appears beside the [] and the
corresponding preset is included in the
scan.
M
SCAN 1
0S
5
10
15
20
25
30
1
6
11
16
21
26
31
2
7
12
17
22
27

1/16
3
8
13
18
23
28
4
9
14
19
24
29

 SCAN numbers configured for a certain page can be saved only in the corresponding
page. Make sure to save it before moving to the next page.
40_ setup
Z6806125901A-SCP-2250(P)-ENGLISH40 40
2010-07-21 오후 6:04:
Auto Play Setup
AUTO PLAY runs configured AUTO PAN, PATTERN, and SCAN functions
automatically.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<AUTO SET>.
 AUTO PLAY1 : Sets overall function
properties of the AUTO PLAY.
- AUTO RETURN : Sets the interval
between auto plays.
- AUTO PLAY : Sets the auto play action
at every auto play interval.
You can set between 1 ~ 4 for SCAN
or AUTO PAN, 1 ~ 3 for PATTERN,
and 0 ~ 511 for PRESET.
- PLAY NUMBER : Sets the number of
the defined auto play operation.
 AUTO PLAY2 : Select the auto play
action and set its starting / ending time.
When the time hits the defined starting
time, configured auto play will begin.
You can set between 1 ~ 4 for SCAN or
AUTO PAN, 1 ~ 3 for PATTERN, and
0 ~ 511 for PRESET.
Z6806125901A-SCP-2250(P)-ENGLISH41 41

AUTO SET

AUTO PAN
1
PATTERN
SCAN
1
AUTO PLAY
2 3 4
1  2  3 
2 3 4
1
● setup
2. Select the <AUTO PLAY> and select a
number.
AUTO PLAY setup screen appears.
AUTO PLAY 1
AUTO RETURN
AUTO PLAY
PLAY NUMBER
ID:START
1 00:00
2 03:00
3 06:00
4 09:00
5 12:00
6 15:00
7 18:00
8 21:00
1MIN
PRESET
0
AUTO PLAY 2
END PLAY
03:00 OFF
06:00 OFF
09:00 OFF
12:00 OFF
15:00 OFF
18:00 OFF
21:00 OFF
00:00 OFF
NO.
0
0
0
0
0
0
0
0
English _41
2010-07-21 오후 6:04:
setup
ZONE SET
You can set the north direction and the zone coverage.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<ZONE SET>.
 MAIN MENU 
PROFILE
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
PRESET
AUTO SET
ZONE SET
ALARM SET
CLOCK SET
OTHER SET
2. Set <AZIMUTH> to <ON>.
3. Set the north direction using the joystick
and press [ENTER].
 SET NORTH : In SET NORTH, press
[ENTER] to set the north direction
which will be the reference for all other
directions.

ZONE SET

AZIMUTH
ZONE AREA SET
OFF
OFF
4. Set <ZONE AREA SET> to <ON>.
5. When the <ZONE AREA MAP> screen
appears, select a number.
6. When the <ZONE AREA SET> screen
appears, set the <POSITION> and
<ZONE ID SET>.
ZONE AREA MAP
1
2
3
4
5
6
7
8
 For entering the name, refer to “CAMERA ID”.
(page 24)
 POSITION : Sets the left/right boundaries
of the zone.
42_ setup
Z6806125901A-SCP-2250(P)-ENGLISH42 42
2010-07-21 오후 6:04:
ALARM SET
It provides 8 alarm inputs and 3 alarm outputs. Detects alarm inputs from the external
sensors cooperating with configured presets, patterns, and scan functions, and
produces alarm outputs. Alarm’s dwell time is defined by the corresponding preset’s
<DWELL TIME> and its alarm action.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<ALARM SET>.
● setup
 MAIN MENU 
PROFILE
CAMERA SET
INTELLIGENCE
PRIVACY ZONE
PRESET
AUTO SET
ZONE SET
ALARM SET
CLOCK SET
OTHER SET
2. Select each item and set appropriately.

ALARM SET

ALARM PRIORITY SET
ALARM IN SET
ALARM OUT SET
AUTO SET
AUX OUT CONTROL
 ALARM PRIORITY : Sets the priorities of
alarms. Setting the priorities of 8 alarms
defines the alarm notification priorities
of them in the highest orders.
By default, the priorities are set as
Alarm 1  Alarm 2  .....  Alarm 8.
When multiple alarms are generated
at the same time, alarm notifies in the
order of the default priority setting.
While an alarm is generating, no motion
is detected.
Z6806125901A-SCP-2250(P)-ENGLISH43 43
ALARM PRIORITY SET
ALARM1
ALARM2
ALARM3
ALARM4
ALARM5
ALARM6
ALARM7
ALARM8
1
2
3
4
5
6
7
8
English _43
2010-07-21 오후 6:04:
setup
 ALARM IN SET : Select the alarm sensor
AUTO SET
operation between <NO>, <NC> and
ALARM1
OFF
<OFF>.
ALARM2
OFF
ALARM3
OFF
 ALARM OUT SET : Set the alarm out
ALARM4
OFF
port matched to the alarm input port.
ALARM5
OFF
ALARM6
OFF
 AUTO SET : Sets the pattern and scan
ALARM7
OFF
action for the corresponding alarm
ALARM8
OFF
input. When the alarm is generated, the
MOTION
OFF
camera moves to the preset position
coupled to the corresponding alarm.
Presets 1 ~ 8 are coupled with alarms
1 ~ 8 inputs respectively, and the preset 9 is coupled to the motion
detection.
The camera stops and remains in the corresponding preset position for the
defined <DWELL TIME>, and performs pattern or scan action defined by
the <AUTO SET>. Setting to <OFF> will discard with the pattern or scan
action after moving to the preset position.
- PATTERN 1 ~ 3 : Defined pattern action
- HALF1 : Patterns 1 and 2 in serial action
- HALF2 : Patterns 2 and 3 in serial action
- WHOLE : Patterns 1, 2 and 3 in serial action
- SCAN 1 ~ 4 : Predefined SCAN action
M
 The <ALARM1> is used as external switching signal if the <DAY/NIGHT> is set to
<EXT>.
 AUX OUT CONTROL : Sets whether to
sustain the alarm output despite of the
alarm generation or to output alarm out
signal while the coupled alarm is alive.
When selected <OFF>, outputs alarm
only if the alarm is generated. When
selected <ON>, it always outputs
alarm out signal despite of the alarm
generation.
AUX OUT CONTROL
OUT1
OUT2
OUT3
OFF
OFF
OFF
44_ setup
Z6806125901A-SCP-2250(P)-ENGLISH44 44
2010-07-21 오후 6:04:
CLOCK SET
Sets whether to display the clock on the screen and its time format.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<CLOCK SET>.
2. Select <DISPLAY> and set whether to
display the time on the screen.
4. Select the date format and set the date.
CLOCK SET

OFF
12HOUR
AM 07:34:48
MM/DD/YYYY
01/01/2009
● setup
3. Select the time format and set the clock.

DISPLAY
TIME FORMAT
SET TIME
DATE FORMAT
SET DATE
OTHER SET
You can reset the system by running FACTORY DEFAULTS, or set the font color, zoom,
turbo pan/tilt, etc.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<OTHER SET>.
2. Select each item and set appropriately.
Z6806125901A-SCP-2250(P)-ENGLISH45 45

OTHER SET
LANGUAGE
FACTORY DEFAULTS
OSD COLOR
PROPORTIONAL P/T
P/T SPEED
AUTO CAL.
D-FLIP
PASSWORD

ENGLISH
[2]
BW
ON
OFF
OFF
OFF
English _45
2010-07-21 오후 6:04:
setup
Language
Select <LANGUAGE> and use the left/right
button to select a preferred display language.

OTHER SET
LANGUAGE
FACTORY DEFAULTS
OSD COLOR
PROPORTIONAL P/T
P/T SPEED
AUTO CAL.
D-FLIP
PASSWORD

ENGLISH
[2]
BW
ON
OFF
OFF
OFF
FACTORY DEFAULTS
When selected, the <FACTORY DEFAULTS>
screen appears and you can reset all settings
to the factory default settings by selecting
the <OK>. However, the protocol, baud rate,
address and the language settings will not be
reset.
FACTORY DEFAULTS
M
OK
CANCEL
 Note that the resetting the system to the
factory default will erase all settings data.
OSD COLOR
Selects the color of the on-screen display font.
PROPORTIONAL P/T
When selected <ON>, manual pan / tilt movement speed will vary proportionally to
the zoom ratio.
P/T SPEED
When selected <ON>, manual pan / tilt movement speed will be doubled.
46_ setup
Z6806125901A-SCP-2250(P)-ENGLISH46 46
2010-07-21 오후 6:04:
AUTO CAL. (AUTO CALIBRATION)
To enhance the lens and pan/tilt motor’s accuracy, the automatic compensation
function is provided. It automatically resets the lens and pan/tilt when there is no
user operation for a specified time period.
D-FLIP (DIGITAL FLIP)
PASSWORD
When selected <ON>, it is asked to enter the
password for accessing the menu.
Select the numbers using direction keys and
press [ENTER].
● setup
When selected <ON>, the displayed screen will be flipped vertically and horizontally
if the subject turns over 90°.
PASSWORD
0
5
1
6
 The default password is “4321”.
2
7
3
8
4
9
[]
[]
COMMUNICATION
You can set the RS-485 communications setting in regard of the camera.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<COMMUNICATION>.
2. Select each item and set appropriately.
 PRIORITY : Set the priority by selecting
<HW> or <SW>.
When selected <HW>, the protocol,
baud rate and address settings will
follow those settings of the adaptor
switch.
 PROTOCOL, BAUD RATE, ADDRESS :
When selected <SW>, you can manually
set the protocol, baud rate and address.
Z6806125901A-SCP-2250(P)-ENGLISH47 47

COMMUNICATION
RS485
PRIORITY
PROTOCOL
BAUD RATE
ADDRESS

HW
SAMSUNG
HALF
9600
0
English _47
2010-07-21 오후 6:04:
setup
SYSTEM INFO
You can check the system information.
For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20)
1. Select <MAIN MENU>-<SYSTEM INFO>.
2. The current system information is displayed.

SYSTEM INFO
TYPE
PROTOCOL
ADDRESS
COMM. TYPE
BAUD RATE
SERIAL NO.
CAMERA VER.
ALARM VER.

4_PTZ_NOR_P
SAMSUNG
0
HW, RS485, HALF
9600
000000000000000
v2.00_100501
v2.00_100501
48_ setup
Z6806125901A-SCP-2250(P)-ENGLISH48 48
2010-07-21 오후 6:04:
appendix
Shortcut Keys
ALARM SET
OTHER SET
AUTO SET
Function
Key
[PRESET] + [5] + [1] + [2] + [ENTER]
DAY/NIGHT - NIGHT
[PRESET] + [5] + [1] + [3] + [ENTER]
DAY/NIGHT - AUTO
[PRESET] + [5] + [1] + [4] + [ENTER]
DAY/NIGHT - EXT
[PRESET] + [5] + [1] + [5] + [ENTER]
IRIS - ALC
[PRESET] + [5] + [1] + [8] + [ENTER]
IRIS - MANU
[PRESET] + [5] + [1] + [9] + [ENTER]
FOCUS MODE – AF
[PRESET] + [5] + [2] + [0] + [ENTER]
FOCUS MODE – MF
[PRESET] + [5] + [2] + [1] + [ENTER]
FOCUS MODE – ONEAF
[PRESET] + [5] + [2] + [2] + [ENTER]
AUX OUT CONTROL – OUT1 – ON
[PRESET] + [5] + [2] + [3] + [ENTER]
AUX OUT CONTROL – OUT1 – OFF
[PRESET] + [5] + [2] + [4] + [ENTER]
AUX OUT CONTROL – OUT2 – ON
[PRESET] + [5] + [2] + [5] + [ENTER]
AUX OUT CONTROL – OUT2 – OFF
[PRESET] + [5] + [2] + [6] + [ENTER]
AUX OUT CONTROL – OUT3 – ON
[PRESET] + [5] + [2] + [7] + [ENTER]
AUX OUT CONTROL – OUT3 – OFF
[PRESET] + [5] + [2] + [8] + [ENTER]
PROPORTIONAL P/T – ON
[PRESET] + [5] + [2] + [9] + [ENTER]
PROPORTIONAL P/T – OFF
[PRESET] + [5] + [3] + [0] + [ENTER]
P/T SPEED – 9
[PRESET] + [5] + [3] + [1] + [ENTER]
P/T SPEED – 5
[PRESET] + [5] + [3] + [2] + [ENTER]
D-FLIP – ON
[PRESET] + [5] + [3] + [3] + [ENTER]
D-FLIP – OFF
[PRESET] + [5] + [3] + [4] + [ENTER]
AUTO PLAY – 1
[PRESET] + [5] + [3] + [5] + [ENTER]
AUTO PLAY – 2
[PRESET] + [5] + [3] + [6] + [ENTER]
AUTO PLAY – OFF
[PRESET] + [5] + [3] + [7] + [ENTER]
Running A.C (Auto Calibration)
[PRESET] + [5] + [3] + [8] + [ENTER]
Z6806125901A-SCP-2250(P)-ENGLISH49 49
● appendix
CAMERA SET
Function
DAY/NIGHT - DAY
English _49
2010-07-21 오후 6:04:
appendix
Specifications
Item
Description
Product Type
SMART DOME CAMERA
Power Source
AC 24 V (60 Hz)
Power Consumption
11.5W
TV Standard
NTSC / PAL STANDARD COLOR SYSTEM
Image Sensor
Super-HAD IT CCD
Effective Pixels
PAL-752(H) × 582(V)
NTSC-768(H) × 494(V)
TV line frequency
PAL-Horizontal : 15, 625 Hz (INT) / 15, 625 Hz (L/L)
Vertical : 50 Hz (INT) / 50 Hz (L/L)
NTSC-Horizontal : 15, 734 Hz (INT) / 15, 750 Hz (L/L)
Vertical : 59.94 Hz (INT) / 60 Hz (L/L)
Synchronization
INT/LINE LOCK
Resolution
Horizontal : 600 TV LINES
Vertical : 350 TV LINES
S/N Ratio
Approximately 52 dB
Minimum subject
illumination
SENS-UP
Illumination
Color
B/W
Off
50IRE
0.20 Lux
0.02 Lux
Off
30IRE
0.12 Lux
0.012 Lux
Off
15IRE
0.06 Lux
0.006 Lux
x512
50IRE
0.00039 Lux
0.00004 Lux
x512
30IRE
0.00023 Lux
0.00002 Lux
x512
15IRE
0.00012 Lux
0.00001 Lux
Signal Output
COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC
Lens
x25 Zoom Lens Integrated
Focal length : 3.66 ~ 91.36mm
Aperture : F1.65(Wide) F3.0(Tele)
- MOD(Minimum Object Distance) : 1000mm
50_ appendix
Z6806125901A-SCP-2250(P)-ENGLISH50 50
2010-07-21 오후 6:04:
Item
Description
PAN range : 360˚Endless
Preset Pan Speed : 600˚/sec, maximum
Manual Pan Speed : 0.01˚~ 180˚/sec
TILT
Tilt range : -6˚~186˚
Preset Tilt Speed : 600˚/sec, maximum
Manual Tilt Speed : 0.01˚~ 180˚/sec
Remote Control
RS485(Half&Full Duplex)/RS422,
Data on Coaxial Cable
Alarm
Alarm Inputs : 8 IN
Alarm Outputs : 3 OUT (2 Open collector 1 relay)
Operation Temperature
-10°C ~ +50°C
Operation Humidity
~90%
Dimensions (Ø x H)
178 (Ø) x 219(H) mm
Weight
1.85Kg
Product Color
Light Gray
Z6806125901A-SCP-2250(P)-ENGLISH51 51
● appendix
PAN
English _51
2010-07-21 오후 6:04:
appendix
Product Appearance
52_ appendix
Z6806125901A-SCP-2250(P)-ENGLISH52 52
2010-07-21 오후 6:04:
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Z6806125901A-SCP-2250(P)-ENGLISH53 53
2010-07-21 오후 6:04:
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
Z6806125901A-SCP-2250(P)-ENGLISH54 54
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
Z6806125901A
2010-07-21 오후 6:04: