Cobra MT800 Manual - Walkie Talkie Radio Centre

Two-Way Radio Model MT 800
ENGLISH
1. Antenna
2. External Speaker/
Microphone/Charge Jack
3. Mode/Power Button
4. Lock Button
5. Channel Control Buttons
6. Speaker/Microphone
7. Light/Max Range Button
8. Volume Control Buttons
9. Talk Button
10. Call Button
11. Belt Clip
12. Battery Compartment
13. Lock Tab
2
1
CHRG
10
3
9
4
11
8
Printed in China Part No. 480-332-P Version A
5
7
12
6
13
Product Features
• Two-Way Radio
with up to a 5 km (3 mile) range
1
• 8 Channels*
• 38 CTCSS Privacy Codes
• 83 DCS Privacy Codes
• Backlit LCD Display
14
• Battery Saver Circuitry
• Maximum Range Extender
• VOX Mode for Hands-Free Transmissions
• Baby Monitor Function
• Call Alert (10 Selectable Tones)
• Scan (Channel, Privacy Code)
13
• Dual Watch Programmable 2-Location Scan
• Key Lock
• Auto Squelch
• Selectable On/Off "Roger Beep"
Confirmation Tone
• Selectable On/Off Keystroke Tone
• Combination Speaker/Microphone/Charging Jack
• Belt Clip
*You are not allowed to use channels 1 and 2 in France.
This situation can change; please contact the French radio licensing
authority for more information.
1.
2.
3.
4.
5.
6.
7.
Dual Watch Icon
Scan Icon
Roger Beep Icon
DCS Icon
Keystroke Tone Icon
Lock Icon
VOX Icon
8. CTCSS Icon
9. Baby Monitor Icon
10. Battery Low Icon
11. Privacy Code Numbers
12. Power Saver Icon
13. Main Channel Number
14. Receive/Transmit Icon
3
2
4
5
6
7
8
9
10
12
11
OPERATION
English
Product Information
This microTALK® radio has been manufactured to
meet all required standards for radio equipment
using PMR 446 frequencies as authorized. The
use of this two-way radio product involves the
public airways and its use may be subject to local
laws or regulations. Contact your radio licensing
authority for more information.
Each port can charge one radio. Uses 230-volt
adaptor.
Cobra recommends your radio is turned Off while
being charged.
Radio Power
To Turn Your Radio On:
Mode/Power Button
Press and hold the
MODE/POWER button until
Caring for Your Radio
you hear a series of audible
tones indicating that the radio
Your microTALK® radio will give you years of
trouble-free service if cared for properly. Here are is On.
a few suggestions:
Your microTALK® radio is now in LISTENING MODE,
ready to receive transmissions. The radio is always
• Handle the radio gently.
in LISTENING MODE, except when the TALK, CALL
• Keep it away from dust.
• Never put the radio in water or in a damp place. or MODE buttons are pressed.
To Turn Your Radio Off:
• Avoid exposure to extreme temperatures.
– Press and hold the POWER button.
Charger and Rechargeable
Batteries
To Insert Batteries in
Radio:
1. Remove belt clip by
releasing belt clip latch and
sliding clip up.
2. Pull up on lock tab to
remove battery cover (on
back of radio).
3. Insert batteries according to
polarity markings.
Remove Belt Clip
Lock Tab
NOTE: Estimated operation time Insert Batteries
on full charge: 12 hours.
These rechargeable batteries
must be recycled or disposed
of properly in compliance with
all applicable laws. They must
not be thrown in the rubbish bin. Some countries
and local authorities require recycling and have
established collection programs. Please contact
your local waste disposal authority for instructions.
WARNING: Do not put batteries into fire or expose
to high heat. They may explode.
For Charging microTALK® Radio(s):
1. Check to see that the batteries have been
inserted properly. See
above for battery
Wall Charger
installation instructions.
2. Insert round connector of
wall charger into the
charge jack located at the
Insert Connector
top of the radio. The wall
charger has two (2) round
connectors which enables
you to charge either one
or two (2) radios at a time.
3. Plug the wall charger into electrical outlet.
It is not recommended to recharge batteries more
than 24 hours. Estimated operation time on a full
charge is 12 hours.
Use only the supplied rechargeable batteries and
wall charger for recharging your microTALK®
radio. Non-rechargeable alkaline batteries can also
be used.
Battery Low Indicator
When battery power is low,
the BATTERY LOW indicator
will blink, indicating that
batteries should be recharged
or replaced.
WARNING: Only the supplied
NiMH batteries
can be recharged.
Battery Low
Battery/Power Saver
Power Saver
If there are no transmissions
within 10 seconds, the unit
will automatically switch to
Battery Save Mode and
POWER SAVER will appear in
the display. This will not affect the unit’s ability
to receive incoming transmissions.
Communicating with
Another Person
Talk Button
1. Press and hold the TALK
button.
2. With the microphone about
5 cm (2 inches) from your
mouth, speak in a normal
5 cm (2 Inches)
voice.
From Mouth
3. Release the button when
you have finished talking
and listen for a response.
You cannot receive incoming
calls while pressing the TALK button.
NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
OPERATION
Listening for a
Response
English
To Illuminate Display
Listening
Release the TALK button to
receive incoming transmissions.
Your microTALK® is always in
LISTENING MODE except when
the TALK, CALL or MODE
buttons are pressed.
To Adjust Volume
Press the VOLUME UP or the
VOLUME DOWN buttons.
A double beep sound is used to
indicate that you have reached
the minimum (1) or maximum
(8) volume level.
Call Button
Press and release the
LIGHT/MAX RANGE button to
illuminate the display for 10
seconds.
Light/Max Range
Button
Auto Squelch/
Maximum Range Extender
Volume Buttons
Volume Level
Call Button
Press and release the CALL
button.
The other person will hear a
two (2) second ringing tone.
You cannot receive transmissions while sending a
call.
NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
Channels
With the radio ON, select any
Channel Buttons
of the 8 channels by pushing
the CHANNEL UP or CHANNEL
DOWN button.
You can press and hold the
CHANNEL UP or CHANNEL
Channels
DOWN button for fast advance.
NOTE: Both radios must be
tuned to the same
channel and privacy
code (see “CTCSS Privacy Codes” or “DCS
Privacy Codes”) to communicate.
Your microTALK® radio is equipped with Auto
Squelch, which automatically shuts off weak
transmissions and unwanted noise resulting from
terrain, conditions, or from reaching your
maximum range limit.
You can temporarily turn Off Auto Squelch or turn
On Maximum Range Extender, allowing all signals
to be received and extending the maximum range
of your radio.
To Temporarily Turn Off Auto Squelch:
– Press the LIGHT/MAX
RANGE button for less than Light/Max Range
Button
five (5) seconds.
If you hear two (2) beeps,
you have turned the
Maximum Range Extender On
(see below).
To Turn Maximum Range Extender On:
– Press and hold the LIGHT/MAX RANGE button
for at least five (5) seconds until you hear two
(2) beeps, indicating that the Maximum Range
Extender is On.
To Turn Maximum Range Extender Off:
– Press and release the LIGHT/MAX RANGE
button or change channels.
microTALK® Range
Your microTALK® radio has a range of up to 5
kilometres (3 miles). Your range will vary
depending on terrain and conditions.
In flat, open country, your
Maximum Range
Lock Function
radio will operate at
maximum range.
The LOCK button locks the CHANNEL UP, CHANNEL
DOWN, and MODE/POWER buttons to prevent
Buildings and foliage in the
accidental operation.
path of the signal can
Reduced Range
reduce the range.
To Use the Lock Function:
Lock
Button
Dense foliage and hilly
– Press and hold the LOCK
terrain will further reduce
button for two (2) seconds
the signal.
to turn the Lock On or Off.
Reduced Range
Remember, you can achieve
A double beep sound is used to
maximum range by using
confirm your Lock On or Off
Lock Icon
Maximum Range Extender.
request. When the radio is in
See above for details.
Lock Mode, the Lock icon will
be displayed.
OPERATION and
MODE FUNCTIONS
External Speaker/Microphone/
Charge Jack
External Speaker/
Your microTALK® radio can be
Microphone/
fitted with an external
Charge Jack
speaker/microphone, freeing
CHRG
your hands for other tasks.
To Attach the External
Speaker/Microphone or
Charger:
1. Open the charge tab on top of the radio.
2. Insert the plug into the jack.
Earbud Microphone
1. Plug earbud microphone into
radio.
2. Place earbud in ear.
3. Clip microphone onto
clothing 76 mm to 152 mm
(3" to 6") from your mouth.
4. Push to talk.
Radio Charger Jack
1
Placed in Ear
2
Clipped to Clothing
3
Clipped to Clothing
4
Scrolling Through the Mode
Functions
English
To Select a CTCSS Privacy
Code:
Mode Button
1. After selecting a channel,
press and release the
MODE button until the
CTCSS icon flashes on the
CTCSS OFF
display. In addition to the
CTCSS icon, either OFF or
the small numbers next to
the channel number will
also flash on the display.
Select Privacy Code
2. If CTCSS and OFF are
flashing, press the CHANNEL
UP or CHANNEL DOWN
button to exit OFF and
Channel Buttons
proceed to select a privacy
code. Or, if CTCSS and the
small numbers next to the
channel number are
flashing, press the CHANNEL
UP or CHANNEL DOWN button to select a
privacy code.
3. When your desired privacy code is displayed,
choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for 15 seconds to
enter the new setting and return to
LISTENING MODE.
DCS Privacy Codes
DCS (Digital Coded Squelch) is Mode Button
an advanced digital coding
system allowing you to select
one of 83 privacy codes to
reduce incoming transmissions
DCS OFF
from other users on the
channel.
NOTE: If you are using a DCS
code, both radios must
be tuned to the same
Select Privacy Code
channel and DCS privacy
code to communicate.
Each channel will
remember the last
privacy code you
Channel Buttons
selected.
To Select a DCS Privacy
Code:
1. After selecting a channel,
press and release the MODE button until the
CTCSS Privacy Codes
DCS icon flashes on the display. In addition to
CTCSS (Continuous Tone Coded Squelch System) is
the DCS icon, either OFF or the small numbers
an advanced tone coding system allowing you to
next to the channel number will also flash on
select one of 38 privacy codes to reduce incoming
the display.
transmissions from other users on the channel.
2. If the DCS and OFF are flashing, press the
NOTE: If you are using a CTCSS privacy code, both
CHANNEL UP or CHANNEL DOWN button to exit
radios must be tuned to the same channel
OFF and proceed to select a privacy code. Or, if
and CTCSS privacy code to communicate.
DCS and the small numbers next to the
Each channel will remember the last privacy
channel number are flashing, press the
code you selected.
CHANNEL UP or CHANNEL DOWN button
to select a privacy code.
By scrolling through the Mode Functions, you will
be able to select or change preferred features of
your microTALK® radio. While you are scrolling
through the Mode Functions, your radio features
will be displayed in the same predetermined order:
Set CTCSS Privacy Codes
Set DCS Privacy Codes
Set VOX On/Off
Set VOX Sensitivity Level
Set Channel Scan
Set CTCSS Privacy Code Scan
Set DCS Privacy Code Scan
Program Dual Watch Location or
Set Dual Watch On/Off
Set Baby Monitor
Set Call Tones
Set “Roger Beep” On/Off
Set Keystroke Tones On/Off
MODE FUNCTIONS
OPERATION
3. When your desired privacy code is displayed,
choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for 15 seconds to
enter the new setting and return to
LISTENING MODE.
English
Channel Scan
Your microTALK® radio can automatically scan
channels (1 to 8).
NOTE: The radio ignores specific CTCSS or DCS
privacy codes while scanning channels.
To Scan Channels:
1. Press the MODE button until Mode Button
the Scan icon and the
channel number flash on
the display.
Voice Activated Transmit (VOX)
In VOX Mode, your microTALK® radio can be used 2. Press the CHANNEL UP or
Select Scan Channels
CHANNEL DOWN button to
“hands-free,” automatically transmitting when you
begin scanning channels.
speak. You can set the VOX sensitivity level to fit
the volume of your voice and avoid transmissions The Scan icon will continue to
triggered by background noise.
be displayed when channel
Mode Button
Channel Buttons
scan is On. Your radio will
To Turn VOX Mode On or
continue to scan all channels
Off:
and stop if an incoming
1. Press the MODE button until
transmission is detected. Your
the VOX icon flashes on the
radio will remain on that
display. The current On or
Select VOX
channel for 10 seconds.
Off setting is displayed.
While setting channel scan, if you do not press
2. Press the CHANNEL UP or
any buttons for 15 seconds your radio will
CHANNEL DOWN button to
automatically return to LISTENING MODE on the
turn VOX On or Off.
channel or channel/privacy code displayed before
3. When your desired VOX
Channel Buttons
you entered Mode Functions.
Mode setting is displayed,
choose one of the
following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for 15 seconds to
enter the new setting and return to
LISTENING MODE.
To Set the VOX Sensitivity Level:
1. Press the MODE button until Mode Button
the VOX icon flashes and
the current sensitivity level
is displayed.
The current sensitivity level is
Select VOX
displayed with the letter “L”
Sensitivity Level
and a number 1 to 5, 5 being
the most sensitive level and 1
being the least sensitive level.
2. Press the CHANNEL UP or
CHANNEL DOWN button to
Channel Buttons
change the setting.
3. When your desired VOX
sensitivity level is displayed,
choose one of the
following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for 15 seconds to
enter the new setting and return to
LISTENING MODE.
During An Incoming Transmission,
You Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that channel. Your radio will
remain on that channel and return to
LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume scanning channels.
If you press the TALK button while scanning and
not within 10 seconds of receiving a transmission,
you will transmit on the channel on which you last
received a transmission. This will return the radio
to LISTENING MODE.
If you do not press any button within 10 seconds,
your radio will automatically resume scanning
channels.
During Scanning (while not receiving
a transmission), You Can Choose From
The Following:
a. Press and hold the TALK button to
communicate on either the channel or
channel/privacy code that was displayed
before you entered Mode Functions or the
channel on which, during scanning, you last
received a transmission. This will return the
radio to LISTENING MODE.
b. Press the MODE button to proceed to set
privacy code on the channel that was either
displayed before you entered Mode Functions
on which, during scanning, you last received a
transmission (see “CTCSS Privacy Code Scan”
or “DCS Privacy Code Scan” for further details).
MODE FUNCTIONS
OPERATION
c. Press the LOCK button to return to
LISTENING MODE on either the channel or
channel/privacy code that was displayed
before you entered Mode Functions or the
channel on which, during scanning, you last
transmitted or received.
CTCSS Privacy Code Scan
Your microTALK® radio can automatically scan
the CTCSS privacy codes (01 to 38) within one
(1) channel.
To Scan Privacy Codes:
1. While in LISTENING MODE,
Select Channel
press the CHANNEL UP or
CHANNEL DOWN button to
choose the channel on
which you wish to scan the
Mode Button
CTCSS privacy codes.
2. Press the MODE button until
the Scan icon and the small
numbers next to the
channel number flash on
Select Scan Privacy
the display.
Codes
3. Press the CHANNEL UP or
CHANNEL DOWN button to
begin scanning CTCSS
privacy codes within the
Channel Buttons
channel you selected.
The Scan icon will continue to be displayed when
CTCSS privacy code scan is On. Your radio will
continue to scan CTCSS privacy codes and stop as
an incoming transmission is detected. Your radio
will remain on that channel/privacy code for 10
seconds.
While setting CTCSS privacy code scan, if you do
not press any buttons for 15 seconds your radio
will automatically return to LISTENING MODE on
the channel/privacy code that was displayed
before you entered Mode Functions.
During An Incoming Transmission,
You Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that channel/privacy code.
Your radio will remain on that
channel/privacy code and return
to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume scanning CTCSS privacy
codes.
If you press the TALK button while scanning
and not within 10 seconds of receiving
a transmission, you will transmit on the
channel/privacy code on which you last received
a transmission. This will return the radio to
LISTENING MODE.
English
If you do not press any button within 10 seconds,
your radio will automatically resume scanning
CTCSS privacy codes.
During Scanning (while not receiving
a transmission), You Can Choose From
The Following:
a. Press and hold the TALK button to
communicate on either the channel or
channel/privacy code that was displayed
before you entered Mode Functions or
channel/privacy code on which, during
scanning, you last received a transmission.
This will return the radio to LISTENING
MODE.
b. Press the MODE button to proceed to next
available Mode Function.
c. Press the LOCK button to return to
LISTENING MODE on either the channel or
channel/privacy code that was displayed
before you entered Mode Functions or the
channel/privacy code on which, during
scanning, you last received a transmission.
DCS Privacy Code Scan
You can automatically scan the DCS privacy codes
(01 to 83) within one channel.
To Scan DCS Privacy
Codes:
Select Channel
1. While in the LISTENING
MODE, press the CHANNEL
UP or CHANNEL DOWN
button to choose the
Mode Button
channel on which you wish
to scan the DCS privacy
codes.
2. Press the MODE button until
the SCAN icon, DCS icon
Select Scan Privacy
and the small numbers next Codes
to the channel number flash
on the display.
3. Press the CHANNEL UP or
CHANNEL DOWN button to
Channel Buttons
begin scanning DCS privacy
codes within the channel
you selected.
The scan icon will continue to
be displayed when DCS privacy
code scan is ON. Your radio will continue to scan
DCS privacy codes and stop when an incoming
transmission is detected. The radio will remain on
that channel/privacy code for 10 seconds.
While setting DCS privacy code scan, if you do not
press any buttons for 15 seconds your radio will
automatically return to LISTENING MODE on the
channel/privacy code that was displayed before
you entered more functions.
MODE FUNCTIONS
OPERATION
During Scanning (While Receiving an
Incoming Transmission), You Can Choose
from the Following:
a. Press and hold the TALK button to
communicate on that channel/privacy code.
Your radio will remain on that
channel/privacy code and return to
LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume scanning DCS privacy
codes.
If you press the TALK button while scanning and
not within 10 seconds of receiving a transmission,
you will transmit on the channel/privacy code on
which you last received a transmission. This will
return the radio to LISTENING MODE.
During Scanning (While Not Receiving
an Incoming Transmission), You Can
Choose from the Following:
a. Press channel/privacy code that was
displayed before you entered Mode
Functions or channel/privacy code on which,
during scanning, you last received a
transmission. This will return the radio to the
LISTENING MODE. Press and hold the TALK
button to communicate on either the
channel or channel MODE.
b. Press the MODE button to proceed to next
available Mode Function.
c. Press the LOCK button to return to
LISTENING MODE on either the channel or
channel/privacy code that was displayed
before you entererd Mode Functions or the
channel/privacy code on which, during
scanning, you last received a transmission.
English
Dual Watch
Dual Watch allows you to simultaneously monitor
any two (2) Dual Watch Locations:
Dual Watch Location 1 – is always the
channel/privacy code displayed before
you entered Mode Functions. See
“Channels,” “CTCSS Privacy Codes” and
“DCS Privacy Codes” sections for further
details.
Dual Watch Location 2 – will be stored in the
radio. It can be edited and/or recalled for
future engagements of Dual Watch Mode.
To Program Or Edit Dual Watch
Location 2 And Engage
Dual Watch Mode:
Mode Button
1. Press the MODE button until
the Dual Watch icon and the
channel number flash on
the display.
Select Dual Watch
2. Choose one of the
following:
a. Select or edit a channel:
1) Press the CHANNEL
Channel Buttons
UP or CHANNEL
DOWN button to
select a channel
(1 to 8).
b. Select or edit a channel/privacy code:
1) Press the CHANNEL UP or CHANNEL
DOWN button to select a channel
(1 to 8).
2) Press the MODE button to set the
channel. The small numbers next to the
channel number will flash on the display.
3) Press the CHANNEL UP or CHANNEL
DOWN button to select a CTCSS privacy
code (01 to 38) or DCS privacy code
(01 to 83).
Lock Button
3. Press the LOCK button to
set Dual Watch Location 2
and engage DUAL WATCH
MODE (see below for
further details).
NOTES: To terminate Dual Watch and proceed
to the next available Mode Function,
press the MODE button.
While setting Dual Watch Location 2,
if you do not press any buttons for 15
seconds your radio will automatically
return to LISTENING MODE on Dual Watch
Location 1.
MODE FUNCTIONS
OPERATION
English
To Turn Dual Watch On:
NOTE: Dual Watch Location 2 must be
programmed to turn Dual Watch on.
1. Set the first Dual Watch
Select Channel
Location (channel/privacy
code) you wish to monitor
(see “Channels,” “CTCSS
Privacy Codes” and “DCS
Privacy Codes” sections for
further details).
Mode Button
2. Press the MODE button until
the Dual Watch icon and the
channel number flash on
the display.
NOTE: While setting Dual Watch, if you do not
press any buttons for 15 seconds your radio
will automatically return to LISTENING
MODE on the last channel or
channel/privacy code displayed before you
entered Mode Functions.
3. Press the LOCK button
Lock Button
to engage DUAL WATCH
MODE.
During Dual Watch (while not receiving
a transmission), You Can Choose From
The Following:
a. Press and hold the TALK button to
communicate on either Dual Watch Location
1 or the last Dual Watch Location on which,
during Dual Watch, you last received a
transmission. This will return the radio to
LISTENING MODE.
b. Press the MODE button to proceed to
other functions.
c. Press the LOCK button to return to
LISTENING MODE on either Dual Watch
Location 1 or the last Dual Watch Location
on which, during Dual Watch, you last
received a transmission.
To Terminate Dual Watch:
Choose one of the following:
a. Press the LOCK button to return to
LISTENING MODE on either Dual Watch
Location 1 or the last Dual Watch Location
on which, during Dual Watch, you last
received a transmission.
b. Press the TALK button to return to
LISTENING MODE on either Dual Watch
Location 1 or the last Dual Watch Location
on which, during Dual Watch, you last
received a transmission.
c. Press the MODE button and proceed to the
next available Mode Function.
During An Incoming Transmission,
You Can Choose From The Following:
a. Press and hold the TALK button to
communicate on that Dual Watch Location.
Your radio will remain on that Dual Watch
Location and return to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume Dual Watch.
If you press the TALK button while in Dual Watch
and not within 10 seconds of receiving a
transmission, you will transmit on the last Dual
Watch Location on which you received a
transmission. This will return the radio to
LISTENING MODE.
If you do not press any button within 10 seconds,
your radio will automatically resume
Dual Watch.
Baby Monitor
With the Baby Monitor Function on, a radio left
near a baby will transmit to another unit on the
same channel and privacy code whenever a sound
is detected. Baby Monitor uses the same
sensitivity level you set for the VOX Function. If
you have not set a VOX sensitivity level (see the
“Voice Activated Transmit [VOX]” section of this
manual), the maximum sensitivity, level 5, will
automatically be used.
To Turn Baby Monitor On:
1. Press MODE button until the Mode Button
Baby Monitor icon flashes
on the display. The current
Off setting is displayed.
2. Press the CHANNEL UP or
Select Baby Monitor
CHANNEL DOWN button to
change the setting to On.
3. Press the LOCK button to
enter the On setting and
enter BABY MONITOR MODE. Channel Buttons
NOTES: Pressing the MODE
button will enter the
Baby Monitor Mode
setting as Off and
Lock Button
proceed to other
Mode Functions.
MODE FUNCTIONS
OPERATION
Not pressing any buttons for 15 seconds
will enter the Baby Monitor Mode setting
as Off and return the radio to LISTENING
MODE.
NOTE: Both radios must be tuned to the same
channel and privacy code to communicate.
To Terminate Baby Monitor Mode:
Choose one of the following:
a. Press the TALK button and return to
LISTENING MODE.
b. Press the LOCK button and return to
LISTENING MODE.
c. Press the MODE button and proceed to
the next available Mode Function.
10 Call Tone Settings
You can choose between 10 different call tone
settings to transmit a unique
Mode Button
call alert.
To Change a Call Tone
Setting:
1. Press the MODE button
until the letter “C” and the
Call Tone Setting
current call tone number
(1 to 10) is displayed. The
current call tone will sound
for two (2) seconds.
Channel Buttons
2. Press the CHANNEL UP
or CHANNEL DOWN button
to hear the other call
tone settings.
3. When your desired call tone setting is
displayed, choose one of the following:
a. Press the MODE button to enter the new
setting and proceed to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for 15 seconds to
enter the new setting and return to
LISTENING MODE.
English
"Roger Beep" Confirmation Tone
Your listener will hear an audible tone when
you release the TALK button. This alerts the other
party that you have finished talking and that it is
OK for them to speak. This feature can be turned
On or Off.
To Turn “Roger Beep” On or Off:
When you turn On your microTALK® radio for the
first time, “Roger Beep” will be On.
1. Press and release the MODE Mode Button
button until the “Roger
Beep” icon flashes on the
display. The current On or
Off setting is displayed.
Select Roger Beep
2. Press the CHANNEL UP or
CHANNEL DOWN button to
select “Roger Beep”
On or Off.
3. When your desired Roger
Channel Buttons
Beep Mode setting is
displayed, choose one
of the following:
a. Press the MODE button
to enter the new setting and proceed
to other functions.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for 15 seconds to
enter the new setting and return to
LISTENING MODE.
The setting you select will be saved when you
turn your radio off and on again. When the
“Roger Beep” is On, the “Roger Beep” icon
will be displayed.
MODE FUNCTIONS
OPERATION
Keystroke Tones
With Keystroke Tones turned On, your radio will
sound beeps each time you press a button or
change a setting.
To Turn Keystroke Tones On or Off:
When you turn On your microTALK® radio for the
first time, Keystroke Tones will be On.
1. Press the MODE button until Mode Button
the Keystroke Tones icon
flashes on the display. The
current ON or OFF setting
is displayed.
Select Keystroke
2. Press the CHANNEL UP or
CHANNEL DOWN button to
turn Keystroke Tones On
or Off.
English
3. When your desired Keystroke Tone Mode
setting is displayed, choose one of the
following:
a. Press the MODE button to enter the new
setting and return to LISTENING MODE.
b. Press the LOCK button to enter the new
setting and return to LISTENING MODE.
c. Do not press any buttons for 15 seconds to
enter the new setting and return to
LISTENING MODE.
The setting you select will be saved when you
turn your radio off and on again. When Keystroke
Tones are On, the keystroke tone icon will
be displayed.
Channel Buttons
D.O.C., WARRANTY
& CUSTOMER SERVICE
Declaration of Conformity
This declaration is the responsibility of the manufacturer/importer
Cobra Electronics Europe Limited
Dungar House
Northumberland Avenue
Dun Laoghaire
County Dublin, Ireland
Date: 15 January 2007
This certifies that the following designated product
PRIVATE MOBILE RADIO: MT 800
(Product Identification)
complies with the essential protection requirements of R & TTE
Directive 1999/5/EC on the approximation of the laws of the
Member States relating to Radio Spectrum Matters, EMC and
Electrical Safety.
This declaration applies to all specimens manufactured in accordance
with the attached technical documentation described in Annex II of
the Directive which forms part of this declaration.
Assessment of compliance of the product (class 2.6) with the
requirements relating to the essential requirements according to
Article 3 R & TTE was based on Annex IV of Directive 1999/5/EC
and the following standards:
Radio Spectrum:
EMC:
Electrical Safety:
RF Exposure:
DUBLIN, IRELAND
EN 300 296-1 V1.1.1 (2001-03)
EN 300 296-2 V1.1.1 (2001-03)
EN 301 489-1 V1.5.1 (2004-11)
EN 301 489-5 V1.3.1 (2002-08)
EN 60950-1:2001 + A11:2004
EN 50392 (2004-02)
MIKE KAVANAGH
English
Warranty & Customer Service
For warranty and customer service information,
please contact your local dealer.
For use in EU countries, subject to local laws and
regulations.
CEEL® is a registered trademark of
Cobra Electronics Europe, Ltd.
Snake design and microTALK® are registered
trademarks of Cobra Electronics Corporation, USA.
©2007 Cobra Electronics Europe Limited
Dungar House, Northumberland Avenue
Dun Laoghaire, County Dublin, Ireland
www.cobra.com
This equipment is intended for use in:
AT
BA
BE
BG
CH
CY
CZ
DE
DK
EE
ES
FI
FR
GB
GR
HR
HU
IE
IS
IT
LT
LV
LI
LU
ME
MK
MT
NL
NO
PL
PT
RO
RS
SE
SI
SK
TR
Countries of use