IMI CORNELIUS REMCOR INC g 500 REGENCY DRIVE g GLENDALE HEIGHTS, IL 60139--2268
Telephone (800) 551--4423
Facsimile (800) 519--4423
Installation Manual
ICE DISPENSER
D45 and D90
Part No. 91561
August, 1995
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
This Manual must be read and understood before installing or operating this equipment
Ó IMI CORNELIUS INC; 1992--95
PRINTED IN U.S.A
TABLE OF CONTENTS
Page
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
CLEANING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
DISPENSER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
DAILY (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WEEKLY (OR AS REQUIRED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
MONTHLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
BLOWN FUSE OR CIRCUIT BREAKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
GATE DOES NOT OPEN. AGITATOR DOES NOT TURN. . . . . . . . . . . . . . . . . . 4
GATE DOES NOT OPEN OR IS SLUGGISH. AGITATOR TURNS. . . . . . . . . . . 4
GATE OPENS. AGITATOR DOES NOT TURN. . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICE DISPENSES CONTINUOUSLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SLUSHY ICE. WATER IN HOPPER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOLENOID ASSEMBLY PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
4
7
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
LIST OF FIGURES
FIGURE 1. MOUNTING TEMPLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 2. WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 3. SOLENOID ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIGURE 4. DISPENSING LEVERS AND SWITCHES . . . . . . . . . . . . . . . . . . . . . . .
5
6
7
8
LIST OF TABLES
TABLE 1. SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
i
1
91561
SAFETY PRECAUTIONS
ALWAYS: Disconnect power to the dispenser before servicing or cleaning.
NEVER: Place hands inside of hopper or gate area without disconnecting power to the dispenser. Agitator
rotation occurs automatically when dispenser is energized!
This ice dispenser has been specifically designed to provide protection against personal injury and eliminates
contamination of ice. To ensure continued protection and sanitation, observe the following:
ALWAYS: Be sure removable lid is properly installed to prevent unauthorized
access to the hopper interior and possible contamination of the ice.
ALWAYS: Be sure the upper and lower front panels are securely fastened.
ALWAYS: Keep area around the dispenser clean of ice cubes.
CAUTION: Dispenser cannot be used with crushed or flaked ice. Use of bagged ice that has
frozen into large chunks can void warranty. The dispenser agitator is not designed to be an
ice crusher. Use of large chunks of ice that “jam up” inside the hopper will cause failure of
the agitator motor and damage to the hopper. If bagged ice is used, it must be carefully and
completely broken into small, cube-sized pieces before filling into the dispenser hopper.
DESCRIPTION
The D45 or D90 ice dispensers solve your ice and beverage service needs in a sanitary, space saving, economical way. Designed to be manually filled with ice from any remote ice-making source, these dispensers will dispense cubes (up to 1-1/4?in size), cubelets and hard-chipped or cracked ice.
Table 1. Specifications
Model:
Ice Storage:
Electrical:
Drain Connection:
Electrical Connection:
Dimensions:
D45
45 pounds
120/1/60, 3 Amps
3/4?FPT
6'
, 3--Wire Cord with 3--Prong Ground Type Plug
16?W x 22?D x 26--1/2?H
Model:
Ice Storage:
Electrical:
Drain Connection:
Electrical Connection:
Dimensions:
D90
90 pounds
120/1/60, 3 Amps
3/4?FPT
6'
, 3--Wire Cord with 3--Prong Ground Type Plug
22?W x 28?D x 30?H
1
91561
INSTALLATION INSTRUCTIONS
1. Locate the dispenser indoors on a level counter top. Unpack the four (4) legs and install them into the
threaded holes provided in the bottom of the unit.
2. Connect the 3/4?IPS (or equal) drain line to the 3/4?threaded drain connections at the lower rear of the
unit. This line must pitch downward to an open drain and must contain no traps, or improper drainage will
result.
3. Clean the hopper interior. (See Cleaning Instructions on page 3.)
4. Connect the power cord to a 120 volt, 60 hertz, 3--wire grounded receptacle. All electrical wiring must conform to national and local electrical codes.
CLEANING INSTRUCTIONS
WARNING: DISCONNECT POWER BEFORE CLEANING! Do not use metal scrapers, sharp
objects or abrasives on the ice storage hopper, top cover and the agitator disk, as damage
may result. Do not use solvents or other cleaning agents, as they may attack the plastic
material.
DISPENSER
1. Clean the ice dispenser interior at least once a month.
2. Lift off agitator assembly and wash and rinse it thoroughly.
3. Wash down the inside of the hopper and top cover with a mild detergent solution and rinse thoroughly to
remove all traces of detergent.
4. Replace the agitator.
5. Sanitize the inside of the hopper and agitator with a solution of 1 ounce of household bleach in 2 gallons of
water.
6. Remove ice chute cover as follows:
A.
Flex sides outward to disengage lower pins.
B.
Lift ice chute cover to disengage upper pins.
C.
Lower ice chute cover down out of unit. NOTE: It may be helpful to twist cover slightly.
7. Clean the inside of the ice chute and ice chute cover with a mild detergent solution and rinse thoroughly to
remove all traces of detergent.
8. Sanitize as described in Step 5.
9. Reverse steps above to reassemble ice chute.
91561
2
OPERATING INSTRUCTIONS
Fill the hopper with ice and replace the lid. Pushing the dispenser lever will cause ice to flow from the ice chute.
Ice flow will continue until the lever is released. If ice does not dispense, see the TROUBLESHOOTING GUIDE
to find the cause.
NOTE: Use caution to avoid spilling ice when filling dispenser. Immediately clean up any spilled ice
from filling or operating the unit. To prevent contamination of ice, the lid must be installed on the unit
at all times.
MAINTENANCE
The following dispenser maintenance should be performed at the intervals indicated:
CLEANING
DAILY (OR AS REQUIRED)
Remove foreign material from the vending area sink to prevent drain blockage.
WEEKLY (OR AS REQUIRED)
Clean the vending area. Check for proper water drainage from the vending area sink.
MONTHLY
Clean and sanitize the hopper interior. (See CLEANING INSTRUCTIONS.)
If the dispenser fails to dispense ice when operated, check that the hopper has ice in it and that power is being
supplied to the unit. If the problem persists, check the following:
1. Determine if the agitator is rotating (check for the sound of ice movement in the hopper).
2. Observe whether the gate is operating.
After checking the above, refer to the TROUBLESHOOTING GUIDE for possible problem causes and
corrective action.
3
91561
TROUBLESHOOTING GUIDE
Should your unit fail to operate properly, check that there is power to the unit and that the hopper contains ice.
If the unit still does not dispense, check the following chart under the appropriate symptoms to aid in locating
the defect.
Trouble
BLOWN FUSE OR CIRCUIT
BREAKER.
GATE DOES NOT OPEN.
AGITATOR DOES NOT TURN.
GATE DOES NOT OPEN OR
IS SLUGGISH. AGITATOR
TURNS.
GATE OPENS. AGITATOR
DOES NOT TURN.
ICE DISPENSES
CONTINUOUSLY.
SLUSHY ICE. WATER IN
HOPPER.
91561
Probable Cause
Remedy
A.
Short circuit in wiring.
A.
Repair wiring.
B.
Defective gate solenoid.
B.
Replace gate solenoid.
C.
Defective agitator motor.
C.
Replace agitator motor.
A.
No power.
A.
Restore power.
B.
Bent depressor plate (does not
actuate switch).
B.
Replace depressor plate.
C.
Defective dispensing switch.
C.
Replace dispensing switch.
A.
Defective gate solenoid.
A.
Replace gate solenoid.
B.
Weak gate spring.
B.
Replace gate spring.
C.
Excessive pressure against
gate slide.
C.
Reduce pressure against gate
slide.
A.
Ice solidified in hopper.
A.
Break up ice in hopper.
B.
Defective agitator motor.
B.
Replace agitator motor.
C.
Defective capacitor (D90 only).
C.
Replace capacitor.
A.
Stuck or bent depressor plate
(does not release switch)
A.
Replace depressor plate.
B.
Defective dispensing switch.
B.
Replace dispensing switch.
C.
Improper switch installation.
C.
Properly install switch.
A.
Blocked drain.
A.
Open drain.
B.
Unit not level.
B.
Level unit.
C.
Poor ice quality due to water
quality or ice maker problems.
C.
Clean hopper, then replace ice.
4
1 5/8-IN.
15 7/8-IN.
12 5/8-IN.
1 5/8-IN.
D45
18 9/16-IN.
OUTLINE
OF UNIT
21 25/32-IN.
3/4-DIA. (4)
22-IN.
1 1/8-IN.
19 3/4-IN.
1 1/8-IN.
D90
16 1/4-IN.
OUTLINE
OF UNIT
27 23/32-IN.
3/4-DIA. (4)
FIGURE 1. MOUNTING TEMPLATES
5
91561
ICE LEVEL SIGNAL
L N GROUND
GRN
OPTION
T’STAT LIGHT
1
LIGHTED DISPLAY
2
OPTION
WHT
BALLAST
BLK
LIGHT
BLK
WHT
STARTER
WHT
GATE
SOLENOID
1 1/4 AMP TIME
DELAY FUSE
RED
WHT
TERMINAL
BOARD
RED
AGITATOR
MOTOR
PORTION
TIMER
SW OR RED
TD
DISPENSE
CONTROL
OPTION
TO
TERMINAL
RED
PORTION
BLK
DISPENSE
SWITCH
WHT
CAPACITOR
D90 ONLY
SWITCH
RED
BLK
BOARD
SERVICE INFORMATION
ELECTRIC SHOCK HAZARD. DISCONNECT
DANGER!
POWER BEFORE SERVICING UNIT.
7
8
SOLENOID ADJUSTMENT
WHEN REPLACING SOLENOID,
ADJUST TO 7/8 AS SHOWN
BEFORE TIGHTENING
MOUNTING SCREWS.
FIGURE 2. WIRING DIAGRAM
91561
6
1
2
22
4
3
5
4
22
6
19
18
22
20
21
8
16
15
14
11
10
17
19
13
9
12
7
FIGURE 3. SOLENOID ASSEMBLY -- EXPLODED VIEW AND PARTS LIST
Index
No.
Part No.
Qty.
Name
1
21493
1
2#
31551
1
Solenoid Mounting Plate
Solenoid Service Kit
3
70171
2
8--32 x 3/8 Phil Tr HD Screw
4
70121
2
No. 8 Lockwasher
5
50752
3
Isolator
6*
50789
2
Bumper Assembly
7*
70423
1
Cotter Pin
8*
10080
1
Gate Lift Rod
9
10081
1
Gate Lift Rod Bushing
10
50754
1
Gate Arm Bearing
11
21492
1
Gate Lift Arm
12
70043
1
Flatwasher
13*
70422
1
Spring
14
70263
1
1/4-20 x 3/4 Hex Hd Screw
15
70048
1
1/4 Lockwasher
16
70066
1
1/4 Flatwasher
17
10077
1
Pivot Bearing
18
30227
1
1/4 Quick Connect Tab
19
50305
----
Lubricant
20*
21592
1
Solenoid Linkage Pin
21*
70433
2
Retainer Ring
22
51088
----
Loctite
----*
70438
----
Rebuilding Kit
NOTE: * Parts supplied with rebuilding kit.
# 31551 solenoid supplied with items 20 & 21.
7
91561
10
CUP ACTIVATED
7
8
3
2
10
PUSH LEVER
7
8
4
5
FIGURE 4. DISPENSING LEVERS AND SWITCHES
91561
8
PARTS LIST
Item
Description
Part No. D45
Part No. D90
1
Gate Slide
214910
214910
2
Depressor, Cup Activated
215150
215150
3
Depressor Retainer (for 21515)
22644
22644
4
Depressor Push Lever
27126
27126
5
Depressor Retainer (for 27126)
27107
27107
6
Agitator
21517
21629
7
Dispense Switch
30895
30895
8
Switch Boot
31007
31007
9
Switch Spacer
70847
70847
10
Foam Shield
23062
23062
11
Agitator Motor
31106--1
31112--1
12
Motor Shaft Seal
50454
50454
13
Motor Gasket
50481
50481
14
Lid
50748
50791
15
Sink
50750
50793
16
Ice Chute, Back Section
53015
53015
17
Ice Chute Cover
53016
53016
18
Gate Gasket
51891
51891
19
Sink Grill
70426
70441
20
Leg
70419
70419
21
Cleaning Label
90295
90295
22
Wiring Diagram
90615
90788
23
Front Label
91559
91560
24
Capacitor
----------
30774
25
Solenoid Assembly (see page 7)
31093
31093
26
Rebuilding Kit (see page 7)
70438
70438
9
91561
IMI CORNELIUS INC.
ONE CORNELIUS PLACE
ANOKA, MN. 55303--6234
TELEPHONE (800) 238--3600
FACSIMILE (612) 422--3232
WARRANTY
IMI Cornelius Inc. warrants that all equipment and parts are free from defects in material and workmanship under normal use and service. For a copy of the warranty applicable to your Cornelius product, in your country,
please write, Fax or telephone the IMI Cornelius office nearest you. Please provide the equipment model number and the date of purchase.
IMI Cornelius Offices
AUSTRALIA D P.O. 210, D RIVERWOOD, D NSW 2210, AUSTRALIA D (61) 2 533 3122 D FAX (61) 2 534 2166
AUSTRIA D AM LANGEN FELDE 32 D A-1222 D VIENNA, AUSTRIA D (43) 1 233 520 D FAX (43) 1-2335-2930
BELGIUM D BOSKAPELLEI 122 D B-2930 BRAASCHAAT, BELGIUM D (32) 3 664 0552 D FAX (32) 3 665 2307
BRAZIL D RUA ITAOCARA 97 D TOMAS COELHO D RIO DE JANEIRO, BRAZIL D (55) 21 591 7150 D FAX (55) 21 593 1829
ENGLAND D TYTHING ROAD ALCESTER D WARWICKSHIRE, B49 6 EU, ENGLAND D (44) 789 763 101 D FAX (44) 789 763 644
FRANCE D 71 ROUTE DE ST. DENIS D F-95170 DEUIL LA BARRE D PARIS, FRANCE D (33) 1 34 28 6200 D FAX (33) 1 34 28 6201
GERMANY D CARL LEVERKUS STRASSE 15 D D-4018 LANGENFELD, WEST GERMANY D (49) 2173 7930 D FAX (49) 2173 77 438
GREECE D 488 MESSOGION AVENUE D AGIA PARASKEVI D 153 42 D ATHENS, GREECE D (30) 1 600 1073 D FAX (30) 1 601 2491
HONG KONG D 1104 TAIKOTSUI CENTRE D 11-15 KOK CHEUNG ST D TAIKOKTSUE, HONG KONG D (852) 789 9882 D FAX (852) 391 6222
ITALY D VIA PELLIZZARI 11 D 1-20059 D VIMARCATE, ITALY D (39) 39 608 0817 D FAX (39) 39 608 0814
NEW ZEALAND D 20 LANSFORD CRES. D P.O. BOX 19-044 AVONDALE D AUCKLAND 7, NEW ZEALAND D (64) 9 8200 357 D FAX (64) 9 8200 361
SINGAPORE D 16 TUAS STREET D SINGAPORE 2263 D (65) 862 5542 D FAX (65) 862 5604
SPAIN D POLIGONO INDUSTRAIL D RIERA DEL FONOLLAR D E-08830 SANT BOI DE LLOBREGAT D BARCELONA, SPAIN D (34) 3 640 2839 D FAX (34) 3 654 3379
USA D ONE CORNELIUS PLACE D ANOKA, MINNESOTA D (612) 421-6120 D FAX (612) 422-3255
91561
10
CORPORATE HEADQUARTERS:
Remcor Incorporated
500 Regency Drive
Glendale Heights, IL 60139