Datalogic Magellan 1100i Programming instructions

MagellanTM 1100i
On-Counter Presentation Omnidirectional Bar Code Reader
Product Reference Guide
Datalogic ADC, Inc.
959 Terry Street
Eugene, OR 97402
USA
Telephone: (541) 683-5700
Fax: (541) 345-7140
© 2005-2014 Datalogic ADC, Inc.
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may
be reproduced or transmitted in any form or by any means without prior written permission of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or "Datalogic ADC"). Owners of Datalogic products are hereby granted a non-exclusive, revocable license
to reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or
alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear
on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting your Datalogic representative.
Electronic versions may either be downloadable from the Datalogic website (www.datalogic.com) or provided on appropriate
media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please
let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic
reserves the right to change any specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U.
All other brand and product names may be trademarks of their respective owners.
Magellan is a registered trademark of Datalogic ADC, Inc. in many countries, including the U.S.A. and All-Weighs, FirstStrike and
SurroundScan are registered trademarks of Datalogic ADC, Inc. in the U.S.A. OmegaTek, Produce Rail, Productivity Index Reporting
and SmartSentry are all trademarks of Datalogic ADC, Inc.
This product may be covered by one or more of the following patents:
4603262 • 4639606 • 4652750 • 4672215 • 4699447 • 4709369 • 4749879 • 4786798 • 4792666 • 4794240 • 4798943 • 4799164 •
4820911 • 4845349 • 4861972 • 4861973 • 4866257 • 4868836 • 4879456 • 4939355 • 4939356 • 4943127 • 4963719 • 4971176 •
4971177 • 4991692 • 5001406 • 5015831 • 5019697 • 5019698 • 5086879 • 5115120 • 5144118 • 5146463 • 5179270 • 5198649 •
5200597 • 5202784 • 5208449 • 5210397 • 5212371 • 5212372 • 5214270 • 5229590 • 5231293 • 5232185 • 5233169 • 5235168 •
5237161 • 5237162 • 5239165 • 5247161 • 5256864 • 5258604 • 5258699 • 5260554 • 5274219 • 5296689 • 5298728 • 5311000 •
5327451 • 5329103 • 5330370 • 5347113 • 5347121 • 5371361 • 5382783 • 5386105 • 5389917 • 5410108 • 5420410 • 5422472 •
5426507 • 5438187 • 5440110 • 5440111 • 5446271 • 5446749 • 5448050 • 5463211 • 5475206 • 5475207 • 5479011 • 5481098 •
5491328 • 5493108 • 5504350 • 5508505 • 5512740 • 5541397 • 5552593 • 5557095 • 5563402 • 5565668 • 5576531 • 5581707 •
5594231 • 5594441 • 5598070 • 5602376 • 5608201 • 5608399 • 5612529 • 5629510 • 5635699 • 5641958 • 5646391 • 5661435 •
5664231 • 5666045 • 5671374 • 5675138 • 5682028 • 5686716 • 5696370 • 5703347 • 5705802 • 5714750 • 5717194 • 5723852 •
5750976 • 5767502 • 5770847 • 5786581 • 5786585 • 5787103 • 5789732 • 5796222 • 5804809 • 5814803 • 5814804 • 5821721 •
5822343 • 5825009 • 5834708 • 5834750 • 5837983 • 5837988 • 5852286 • 5864129 • 5869827 • 5874722 • 5883370 • 5905249 •
5907147 • 5923023 • 5925868 • 5929421 • 5945670 • 5959284 • 5962838 • 5979769 • 6000619 • 6006991 • 6012639 • 6016135 •
6024284 • 6041374 • 6042012 • 6045044 • 6047889 • 6047894 • 6056198 • 6065676 • 6069696 • 6073849 • 6073851 • 6094288 •
6112993 • 6129279 • 6129282 • 6134039 • 6142376 • 6152368 • 6152372 • 6155488 • 6166375 • 6169614 • 6173894 • 6176429 •
6188500 • 6189784 • 6213397 • 6223986 • 6230975 • 6230976 • 6244510 • 6259545 • 6260763 • 6266175 • 6273336 • 6276605 •
6279829 • 6290134 • 6290135 • 6293467 • 6303927 • 6311895 • 6318634 • 6328216 • 6332576 • 6332577 • 6343741 • 6454168 •
6478224 • 6568598 • 6578765 • 6705527 • 6857567 • 6974084 • 6991169 • 7051940 • 7170414 • 7172123 • 7201322 • 7204422 •
7215493 • 7224540 • 7234641 • 7243850 • 7374092 • 7407096 • 7490770 • 7495564 • 7506816 • 7527198 • 7527207 • 7537166 •
7562817 • 601 26 118.6 • AU703547 • D312631 • D313590 • D320011 • D320012 • D323492 • D330707 • D330708 • D349109 •
D350127 • D350735 • D351149 • D351150 • D352936 • D352937 • D352938 • D352939 • D358588 • D361565 • D372234 •
D374630 • D374869 • D375493 • D376357 • D377345 • D377346 • D377347 • D377348 • D388075 • D446524 • D606544
•EP0256296 • EP0260155 • EP0260156 • EP0295936 • EP0325469 • EP0349770 • EP0368254 • EP0442215 • EP0498366 •
EP0531645 • EP0663643 • EP0698251 • EP01330772 • EP870761 • GB2252333 • GB2284086 • GB2301691 • GB2304954 •
GB2307093 • GB2308267 • GB2308678 • GB2319103 • GB2333163 • GB2343079 • GB2344486 • GB2345568 • GB2354340 •
ISR107546 • ISR118507 • ISR118508 • JP1962823 • JP1971216 • JP2513442 • JP2732459 • JP2829331 • JP2953593 • JP2964278 •
MEX185552 • MEX187245 • RE37166 • RE40071
• Additional patents pending
Table of Contents
Chapter 1. Getting Started........................................................................................................................................................................ 1
About This Manual .............................................................................................................................................................................1
Manual Conventions ................................................................................................................................................................. 1
Connecting the Scanner .....................................................................................................................................................................2
Programming ......................................................................................................................................................................................3
Using the Programming Barcodes ........................................................................................................................................... 3
Resetting the Standard Product Defaults .......................................................................................................................................3
LED and Beeper Indicators ................................................................................................................................................................4
Error Codes ..........................................................................................................................................................................................5
Chapter 2. General Features..................................................................................................................................................................... 7
Double Read Timeout for Linear Labels ...........................................................................................................................................7
Double Read Timeout for 2D Labels .................................................................................................................................................9
Label Gone Timeout ..........................................................................................................................................................................10
Productivity Index Reporting (PIR) ..................................................................................................................................................10
Sleep Mode ........................................................................................................................................................................................11
LED and Beeper Indicators ..............................................................................................................................................................13
Power On Alert .........................................................................................................................................................................13
ERI Active State High ...............................................................................................................................................................13
ERI Timeout ..............................................................................................................................................................................14
Good Read: When to Indicate .................................................................................................................................................15
Good Read Beep Control .........................................................................................................................................................16
Good Read Beep Frequency ....................................................................................................................................................16
Good Read Beep Length ..........................................................................................................................................................17
Good Read Beep Volume ........................................................................................................................................................18
Green Spot ................................................................................................................................................................................18
Aiming Pointer Settings ..........................................................................................................................................................19
Scanning Features ............................................................................................................................................................................20
Targeted Scanning Mode ..............................................................................................................................................................................20
Target Mode Active Time ........................................................................................................................................................20
Target Mode Linger Time ........................................................................................................................................................21
Wake Up Intensity ...................................................................................................................................................................22
Image Capture ...................................................................................................................................................................................23
How to Capture an Image .......................................................................................................................................................23
Image Compression .................................................................................................................................................................24
Image Size ................................................................................................................................................................................24
Image Brightness ....................................................................................................................................................................25
Image Contrast ........................................................................................................................................................................25
Cell Phone Mode ...............................................................................................................................................................................26
Cell Phone Mode Enable .........................................................................................................................................................26
Cell Phone Detection Sensitivity ............................................................................................................................................27
Cell Phone in Target Mode ......................................................................................................................................................29
Chapter 3. Interface Related Features .................................................................................................................................................. 31
Interface Selection ............................................................................................................................................................................33
Interface Features ............................................................................................................................................................................35
Obey/Ignore Host Commands .....................................................................................................................................................................35
Host Transmission Buffers .............................................................................................................................................................................36
RS-232 Interface Features .....................................................................................................................................................37
Hardware Flow Control ..................................................................................................................................................................................39
Intercharacter Delay ........................................................................................................................................................................................40
Software Flow Control ....................................................................................................................................................................................41
Host Echo Quiet Interval ................................................................................................................................................................................42
Signal Voltage: Normal/TTL ..........................................................................................................................................................................43
Beep on ASCII BEL ............................................................................................................................................................................................44
Beep on Not on File .........................................................................................................................................................................................44
Product Reference Guide
i
ACK NAK Options .............................................................................................................................................................................................45
ACK Character ....................................................................................................................................................................................................46
NAK Character ...................................................................................................................................................................................................46
Retry on ACK NAK Timeout ..........................................................................................................................................................................47
ACK NAK Timeout Value ................................................................................................................................................................................47
ACK NAK Retry Count .....................................................................................................................................................................................48
ACK NAK Error Handling .........................................................................................................................................................49
Transmission Failure Indication ..................................................................................................................................................................50
USB-OEM Interface Features .................................................................................................................................................50
USB-OEM Device usage .................................................................................................................................................................................50
IBM ............................................................................................................................................................................................51
IBM Transmit Labels in Code 39 Format ..................................................................................................................................................51
Keyboard Wedge ......................................................................................................................................................................52
USB Keyboard ...........................................................................................................................................................................52
Caps Lock State .................................................................................................................................................................................................54
USB COM Interface Set-up .............................................................................................................................................................. 58
Chapter 4. Data Editing ........................................................................................................................................................................... 59
Data Editing Overview ..................................................................................................................................................................... 59
Please Keep In Mind... .............................................................................................................................................................59
Global Prefix/Suffix ......................................................................................................................................................................... 60
AIM ID ................................................................................................................................................................................................ 62
Label ID ............................................................................................................................................................................................. 63
Case Conversion ............................................................................................................................................................................... 70
Character Conversion ...................................................................................................................................................................... 71
Chapter 5. Symbologies .......................................................................................................................................................................... 73
UPC-A ................................................................................................................................................................................................ 73
Disable/Enable UPC-A ............................................................................................................................................................73
Check Digit Transmission .......................................................................................................................................................74
Expand UPC-A to EAN-13 .......................................................................................................................................................74
Number System Transmission ..............................................................................................................................................75
UPC-A Minimum Reads ..........................................................................................................................................................75
UPC-A In-store Minimum Reads ...........................................................................................................................................76
UPC-E ................................................................................................................................................................................................ 77
Disable/Enable UPC-E ............................................................................................................................................................77
Check Digit Transmission .......................................................................................................................................................77
Number System Digit ..............................................................................................................................................................78
Expand to UPC-E to UPC-A .....................................................................................................................................................78
Expand UPC-E to EAN13 .........................................................................................................................................................79
Minimum Reads .......................................................................................................................................................................79
GTIN ...........................................................................................................................................................................................80
Expand UPC/EAN to GTIN .......................................................................................................................................................80
EAN-13 .............................................................................................................................................................................................. 81
Disable/Enable EAN-13 ..........................................................................................................................................................81
Check Digit Transmission .......................................................................................................................................................81
EAN-13 Flag 1 Character ........................................................................................................................................................82
ISBN ...........................................................................................................................................................................................82
Minimum Reads .......................................................................................................................................................................83
EAN-8 ................................................................................................................................................................................................ 84
Disable/Enable EAN-8 ............................................................................................................................................................84
Check Digit Transmission .......................................................................................................................................................84
Minimum Reads .......................................................................................................................................................................85
EAN Two-Label ................................................................................................................................................................................ 86
EAN Two-Label Type 1 ............................................................................................................................................................86
EAN Two-Label Type 2 ............................................................................................................................................................87
EAN Two-Label Type 3 ............................................................................................................................................................88
EAN Two-Label Type 4 ............................................................................................................................................................89
EAN Two-Label Combined Transmission ...................................................................................................................................... 90
EAN Two-Label Minimum Reads ...........................................................................................................................................91
Price Weight Check Digit ................................................................................................................................................................. 92
Add-ons ............................................................................................................................................................................................ 93
ii
MagellanTM 1100i
2-Digit Addons Minimum Reads .................................................................................................................................................................95
5-Digit Addons Minimum Reads .................................................................................................................................................................96
GS1 DataBar Omnidirectional / Stacked Omnidirectional ...........................................................................................................97
Disable/Enable GS1 DataBar Omnidirectional .....................................................................................................................97
UCC/EAN 128 Emulation ........................................................................................................................................................97
Minimum Reads ......................................................................................................................................................................98
GS1 DataBar Expanded / Expanded Stacked ................................................................................................................................99
Disable/Enable GS1 DataBar Expanded ...............................................................................................................................99
GS1-128 Emulation .................................................................................................................................................................99
Length Control .......................................................................................................................................................................100
GS1 DataBar Expanded Length 1, Length 2 Programming Instructions .........................................................................101
Minimum Reads ....................................................................................................................................................................102
Coupon Read Control .............................................................................................................................................................103
GS1 DataBar Limited ..................................................................................................................................................................... 104
Disable/Enable GS1 DataBar Limited .................................................................................................................................104
GS1-128 Emulation ...............................................................................................................................................................104
Minimum Reads ....................................................................................................................................................................105
Code 39 ........................................................................................................................................................................................... 106
Disable/Enable Code 39 ........................................................................................................................................................106
Check Character Calculation .................................................................................................................................................106
Check Character Transmit ....................................................................................................................................................107
Start/Stop Characters ...........................................................................................................................................................107
Code 39 Full ASCII ..................................................................................................................................................................108
Length Control .......................................................................................................................................................................109
Code 39 Length 1, Length 2 Programming Instructions ...................................................................................................110
Quiet Zones ............................................................................................................................................................................110
Code 39 Stitching ...................................................................................................................................................................111
Minimum Reads ....................................................................................................................................................................111
Code 32 Italian Pharmacode ......................................................................................................................................................... 112
Disable/Enable Code 32 Italian Pharmacode .....................................................................................................................112
Start/Stop Characters ...........................................................................................................................................................112
Code 32 Italian Pharmacode — continued .........................................................................................................................113
Check Character Transmit ....................................................................................................................................................113
Code 128 ......................................................................................................................................................................................... 114
Disable/Enable Code 128 .....................................................................................................................................................114
Disable/Enable EAN 128 ......................................................................................................................................................114
Transmit Function Characters .............................................................................................................................................115
Length Control .......................................................................................................................................................................116
Code 128 Length 1, Length 2 Programming Instructions .................................................................................................117
Code 128 Conversion to Code 39 ..........................................................................................................................................117
Code 128 Stitching .................................................................................................................................................................118
Minimum Reads ....................................................................................................................................................................118
Interleaved 2 of 5 ........................................................................................................................................................................... 119
Disable/Enable Interleaved 2 of 5 .......................................................................................................................................119
Check Digit Calculation ..........................................................................................................................................................119
Check Digit Transmit .............................................................................................................................................................120
Length Control .......................................................................................................................................................................121
Interleaved 2 of 5 Length 1, Length 2 Programming Instructions ...................................................................................122
Interleaved 2 of 5 Stitching ...................................................................................................................................................123
Minimum Reads ....................................................................................................................................................................124
Codabar ........................................................................................................................................................................................... 125
Disable/Enable Codabar .......................................................................................................................................................125
Check Character Verification ................................................................................................................................................125
Check Character Transmit ....................................................................................................................................................126
Length Control .......................................................................................................................................................................127
Codabar Length 1, Length 2 Programming Instructions ...................................................................................................128
Quiet Zones ..................................................................................................................................................................................................... 128
Start/Stop Character Type ....................................................................................................................................................129
Start/Stop Character Transmission ....................................................................................................................................129
Start/Stop Character Match .................................................................................................................................................130
Codabar Stitching ..................................................................................................................................................................130
Minimum Reads ....................................................................................................................................................................131
Product Reference Guide
iii
Code 93 ............................................................................................................................................................................................ 132
Disable/Enable Code 93 ........................................................................................................................................................132
Length Control .......................................................................................................................................................................133
Code 93 Length 1, Length 2 Programming Instructions ...................................................................................................134
Code 93 Stitching ...................................................................................................................................................................135
Minimum Reads .....................................................................................................................................................................135
MSI/Plessey .................................................................................................................................................................................. 136
Disable/Enable MSI/Plessey ...............................................................................................................................................136
Check Digit Verification .........................................................................................................................................................136
Check Digit Transmit .............................................................................................................................................................137
Number of Check Characters ................................................................................................................................................137
Length Control .......................................................................................................................................................................138
MSI/Plessey Length 1, Length 2 Programming Instructions ...........................................................................................139
MSI/Plessey Stitching ...........................................................................................................................................................140
Minimum Reads .....................................................................................................................................................................141
Standard 2 of 5 ............................................................................................................................................................................... 142
Disable/Enable Standard 2 of 5 ...........................................................................................................................................142
Check Digit Verification .........................................................................................................................................................142
Check Digit Transmit .............................................................................................................................................................143
Length Control .......................................................................................................................................................................144
Standard 2 of 5 Length 1, Length 2 Programming Instructions .......................................................................................145
Standard 2 of 5 Stitching ......................................................................................................................................................146
Minimum Reads .....................................................................................................................................................................147
Chapter 6. 2D Symbologies................................................................................................................................................................... 149
2D Symbologies .............................................................................................................................................................................. 149
2D Decode Time Max .............................................................................................................................................................149
PDF 417 ...................................................................................................................................................................................150
Disable/Enable PDF 417 ...............................................................................................................................................................................150
Length Control ................................................................................................................................................................................................151
PDF 417 Length 1, Length 2 Programming Instructions .................................................................................................................152
Micro PDF 417 ........................................................................................................................................................................153
Disable/Enable Micro PDF 417 ..................................................................................................................................................................153
Length Control ................................................................................................................................................................................................154
Micro PDF 417 Length 1, Length 2 Programming Instructions .....................................................................................................155
Datamatrix ..............................................................................................................................................................................156
Disable/Enable Datamatrix .........................................................................................................................................................................156
Length Control ................................................................................................................................................................................................157
Datamatrix Length 1, Length 2 Programming Instructions ............................................................................................................158
QR Code ...................................................................................................................................................................................159
Disable/Enable QR Code ..............................................................................................................................................................................159
Length Control ................................................................................................................................................................................................160
QR Code Length 1, Length 2 Programming Instructions ................................................................................................................161
Maxicode .................................................................................................................................................................................162
Disable/Enable Maxicode ............................................................................................................................................................................162
Length Control ................................................................................................................................................................................................163
Maxicode Length 1, Length 2 Programming Instructions ..............................................................................................................164
Aztec ........................................................................................................................................................................................165
Disable/Enable Aztec ....................................................................................................................................................................................165
Length Control ................................................................................................................................................................................................166
Aztec Length 1, Length 2 Programming Instructions .......................................................................................................................167
Composite Labels ..................................................................................................................................................................168
Disable/Enable GS1 DataBar Omnidirectional 2D Component ....................................................................................................168
Disable/Enable GS1 DataBar Expanded 2D Component .................................................................................................................168
Disable/Enable GS1 DataBar Limited 2D Component ......................................................................................................................169
Chapter 7. Advanced Decoding Features ............................................................................................................................................ 171
Pharmacy Patterns ........................................................................................................................................................................ 171
Inverse Label Reading ................................................................................................................................................................... 172
Appendix A. Product Specifications....................................................................................................................... 173
Optical and Read Performance Parameters ............................................................................................................................... 173
iv
MagellanTM 1100i
Scanner Dimensions ..................................................................................................................................................................... 173
Physical Properties ........................................................................................................................................................................ 174
Electrical Parameters .................................................................................................................................................................... 174
Environmental Parameters .......................................................................................................................................................... 174
Other Parameters .......................................................................................................................................................................... 174
Chapter B. Cable Pinouts ...................................................................................................................................................................... 175
Standard Cable Pinouts (Primary Interface Cables) ................................................................................................................... 175
RS-232 ....................................................................................................................................................................................175
IBM Port 5B/9B/17 ...............................................................................................................................................................175
USB-OEM ................................................................................................................................................................................176
USB, USB Keyboard & USB COM ...........................................................................................................................................176
Keyboard Wedge ....................................................................................................................................................................176
Appendix C. Alpha-Numeric Pad ............................................................................................................................ 177
Appendix D. Default Settings ................................................................................................................................. 179
Defaults by Symbology ................................................................................................................................................................. 179
Interface Default Exceptions ........................................................................................................................................................ 180
IBM Interfaces ........................................................................................................................................................................180
RS-232 Wincor/Nixdorf ........................................................................................................................................................181
Keyboards ...............................................................................................................................................................................182
Appendix E. Keyboard Function Key Mappings.................................................................................................... 183
Keyboard Model Cross Reference ................................................................................................................................................ 183
Appendix F. Host Commands ................................................................................................................................. 191
Accepting RS-232 Commands ...................................................................................................................................................... 191
Appendix G. Sample Symbols................................................................................................................................. 193
1D Symbol Samples ....................................................................................................................................................................... 193
2D Sample Symbols ....................................................................................................................................................................... 195
Composite Sample Symbols ......................................................................................................................................................... 196
Product Reference Guide
v
NOTES
vi
MagellanTM 1100i
Chapter 1
Getting Started
The MagellanTM 1100i Omni-Directional Imaging Scanner offers hands-free scanning for small,
easily handled items and handheld scanning for bulkier items. Its aggressive imaging performance and intuitive operation reduces user training and speeds checkout for better customer
service.
About This Manual
This manual presents advanced user information which includes connection, programming,
product and cable specifications, and other useful references. For additional information, such
as installation, maintenance, troubleshooting and warranty information, see the Quick Reference Guide (QRG). Copies of other publications for this product are downloadable free of
charge from the website listed on the back cover of this manual.
On leaving the factory, units are programmed for the most common terminal and communications settings. If you need to change these settings, custom programming can be accomplished
by scanning the barcodes in this guide.
Bold text and a yellow-highlighted background indicates the most common default setting for a
feature/option.
Manual Conventions
The symbols listed below are used in this manual to notify the reader of key issues or procedures
that must be observed when using the scanner:
Notes contain information necessary
for properly diagnosing, repairing and
operating the scanner.
NOTE
The CAUTION symbol advises you of
actions that could damage equipment
or property.
CAUTION
Product Reference Guide
1
Getting Started
Connecting the Scanner
The scanner kit you ordered to match your interface should provide a compatible cable for your
installation. Use the appropriate instructions below to connect the scanner to the terminal, PC
or other host device.
Upon completing the connection via the appropriate interface instructions below, proceed to
the Interface Related Features section of this manual and scan the barcode to select the correct
interface type.
RS-232 Serial Connection — Turn off power to the terminal/PC and connect the scanner
to the terminal/PC serial port via the RS-232 cable as shown in Figure 1. If the terminal will not
support POT (Power Off the Terminal) to supply scanner power, use the approved power supply
(AC Adapter). Plug the AC Adapter barrel connector into the socket on the RS-232 cable connector and the AC Adapter plug into a standard power outlet.
Figure 1. RS-232 Serial or USB Connection using A/C Adapter
I/F Cable
To Host/Terminal
Connect
Here
A/C Adapter
(if needed)
For 220-230 VAC
adapters, the
cord must be
facing down as
shown in the
illustration. If
installed upwards,
it will pose an
undue strain on the
socket outlet.
USB Connection — Connect the scanner to a USB port on the terminal/PC using the correct
USB cable for the interface type you ordered. Reference Figure 1 and Figure 2.
NOTE
USB installations may require a power connection via an
approved A/C Adapter as shown in Figure 1. For example, this
would be the case if the scanner is connected along with a
number of other devices to a non-powered USB hub.
B
Figure 2. Other Connection Types
US
M
Ke W
or...
IB
2
yb
ed oard
ge
or...
MagellanTM 1100i
Programming
IBM Connection — Connect the scanner to the IBM port on the terminal/PC using the cor-
rect IBM cable. Reference Figure 2.
Keyboard Wedge Connection — Before connection, turn off power to the terminal/PC.
The Keyboard Wedge cable has a ‘Y’ connection from the scanner. Connect the female to the
male end from the keyboard and the remaining end at the keyboard port at the terminal/PC.
Reference Figure 2.
Programming
The scanner is typically factory-configured with a set of default features standard to the interface
type you ordered. After scanning the interface barcode from the Interface Related Features section, you can select other options and customize your scanner through use of the instructions
and programming barcodes available in that section and also the Data Editing and Symbologies
chapters of this manual.
Using the Programming Barcodes
This manual contains feature descriptions and barcodes which allow you to reconfigure your
scanner. Some programming barcode labels, like the label below for resetting defaults, require
only the scan of that single label to enact the change. Most of the programming labels in this
manual, however, require the scanner to be placed in Programming Mode prior to scanning
them. Scan a START/END barcode once to enterProgramming Mode. Once the scanner is in
Programming Mode, you can scan a number of parameter settings before scanning the START/
END barcode a second time, which will then accept your changes, exit Programming Mode and
return the scanner to normal operation.
Resetting the Standard Product Defaults
If you are unsure of what programming options are in your scanner, or you’ve changed some
options and want the factory settings restored, scan the Standard Product Default Settings barcode below. This will copy the factory configuration for the currently active interface to the current configuration.
Standard Product Default Set-
The programming section lists the factory default settings for each of the menu commands for
the standard RS-232 interface in BOLD text on the following pages. Exceptions to default settings for the other interfaces can be found in Appendix D, Default Settings.
Product Reference Guide
3
Getting Started
LED and Beeper Indicators
The scanner’s beeper sounds and its green LED illuminates to indicate various functions or
errors on the scanner. The tables below list these indications. One exception to the behaviors
listed in the tables is that the scanner’s functions are programmable, and may or may not be
turned on. For example, certain indications, such as the power-up beep can be disabled using
programming barcode labels.
Green LED Indications
LED
INDICATION
INDICATION
COMMENT
Power-on 
indication
Bright green flash
Indicates the scanner has finished all its power up tests
and is now ready for operation.
Good Read
Indication
Bright green flash
Indicates a barcode has been read and decoded.
Scanner
Ready
Constant dim green
The scanner is ready for operation.
Sleep Mode
Constant green flash
(100mS on, 1900mS off)
The scanner is in Sleep Mode. To wake the scanner up,
move an object in front of its window or press the button
atop the unit.
Host Disable
Constant green flash at 1 Hz
(100mS on, 900mS off)
The scanner is disabled due to receiving a disble command from the POS terminal.
Diagnostics
Varies (see Error Codes on
page 1-5 for more information)
The LED can provide diagnostic feedback if the scanner
discovers a problem during SelfTest.
Prog. Mode
See Host Disable above.
The scanner is in Programming Mode.
BEEPER FUNCTIONS
BEEPER
INDICATION
INDICATION
COMMENT
Single beep
The Power-On LED indication is a configurable feature
which can be enabled or disabled. When enabled, this
beep Indicates the scanner has finished all its power up
tests and is now ready for operation.
Good Read
Indication
Single beep
The good read beep indication is configurable. Options
include: Enable/disable, frequency, duration and volume. See the Product Reference Guide (PRG) for
more information.
Diagnostics
Varies (see Error Codes on
page 1-5 for more information)
The Beeper can provide diagnostic feedback if the
scanner discovers a problem during SelfTest.
Programming
Mode 
Indications
Varies depending upon the feature(s) being configured.
The Beeper will sound as programming barcode labels
are scanned, indicating progress during scanner configuration.
Power On
Beep
4
MagellanTM 1100i
Error Codes
Error Codes
Upon startup, if the scanner flashes its indicator LED or sounds an unexpected series of beep
tones (other than normal power-up indications), this means the scanner has not passed its automatic Selftest and has entered FRU1 isolation mode. If the scanner is reset or the trigger is
pulled, the sequence will be repeated. The following table describes the LED flashes/beep codes
associated with an error found.
NUMBER OF
LED
FLASHES/
BEEPS
ERROR
1
Configuration
2
Interface PCB
6
Main PCB
10
Button Error
12
Imager Module
13
Software ID
Failure
14
CPLD/Code
Mismatch
CORRECTIVE ACTION
Contact Helpdesk for assistance
1. Field Replaceable Unit (FRU)
Product Reference Guide
5
Getting Started
NOTES
6
MagellanTM 1100i
Chapter 2
General Features
Double Read Timeout for Linear Labels
This Double Read Timeout feature sets a time limit that determines how much time must
pass before reading the same linear label again (e.g. two identical items in succession).
START / END
PROGRAMMING BARCODES
0.1 Second
0.2 Second
0.3 Second
0.4 Second
DEFAULT
0.5 Second
0.6 Second
Product Reference Guide
7
General Features
Double Read Timeout for Linear Labels — cont.
START / END
PROGRAMMING BARCODES
0.7 Second
0.8 Second
0.9 Second
1 Second
8
MagellanTM 1100i
Double Read Timeout for 2D Labels
Double Read Timeout for 2D Labels
This Double Read Timeout feature specifies the minimum allowable time between consecutive good reads of the same PDF 417, Micro PDF 417 Data Matrix, QR Code, Maxicode,
Aztec or Composite label.
START / END
PROGRAMMING BARCODES
1.5 Seconds
1.65 Seconds
1.8 Seconds
DEFAULT
1.95 Seconds
2 Seconds
2.55 Seconds
Product Reference Guide
9
General Features
Label Gone Timeout
This feature sets the time after the last label segment is seen before the scanner prepares for
a new label.
START / END
PROGRAMMING BARCODES
Sets the label gone timeout duration using hex values from 000 to 255 in increments of ten milliseconds
(10ms or 0.01 seconds). To configure this feature, scan the “START/END” barcode above to place the unit in
Programming Mode, then the “Set Linear Label Gone Timeout,” followed by the three digits (zero padded)
from the Alphanumeric table in Appendix C, Alpha-Numeric Pad representing the desired time value. Exit programming mode by scanning the “START/END” barcode again.
DEFAULT SETTING FOR THIS FEATURE: 320 milliseconds (032)
Set Linear Label Gone Timeout
Productivity Index Reporting (PIR)
When PIR is enabled, label quality data is appended to decoded data before being presented
to the POS. The PIR feature allows the scanner to provide information to an external computer, indicating how easy the label was to read.
NOTE
This value-added feature is a factory-programmed option. Contact your dealer for
information about upgrading your system
to include this advanced capability.
START / END
PROGRAMMING BARCODES
Disable
DEFAULT
Enable
10
MagellanTM 1100i
Sleep Mode
Sleep Mode
This feature specifies the amount of time with no barcode reads before the scanner enters
sleep mode.
START / END
PROGRAMMING BARCODES
Disable Sleep Mode
15 Seconds
30 Seconds
1 Minute
2 Minutes
3 Minutes
4 Minutes
5 Minutes
Product Reference Guide
11
General Features
Sleep Mode — cont.
START / END
PROGRAMMING BARCODES
6 Minutes
7 Minutes
8 Minutes
9 Minutes
10 Minutes
DEFAULT
12 Minutes
15 Minutes
30 Minutes
1 Hour
12
MagellanTM 1100i
LED and Beeper Indicators
LED and Beeper Indicators
Power On Alert
Disables or enables the indication (a single beep) that the scanner has finished all its power
up tests and is now ready for operation.
START / END
PROGRAMMING BARCODES
Disable
Enable
DEFAULT
ERI Active State High
This setting specifies the active-state polarity of the External Read Indicator signal to High;
the inactive state is the opposite polarity.
NOTE
Contact Technical Support for assistance in changing the ERI Active State
to Low if needed. Configuration of this
feature is available only through use of
a special cable.
START / END
PROGRAMMING BARCODES
ERI Active State = High
Product Reference Guide
13
General Features
ERI Timeout
Specifies the amount of time the External Read Indicator (ERI) signal is held active for a
good read.
START / END
PROGRAMMING BARCODES
Sets the ERI timeout duration using hex values from 000 to 255 in increments of ten milliseconds (10ms or
0.01 seconds). To configure this feature, scan the “START/END” barcode above to place the unit in Programming Mode, then the “Set ERI Timeout,” followed by the two digits (zero padded) from the Alphanumeric
table in Appendix C, Alpha-Numeric Pad representing the desired time value. Exit programming mode by scanning the “START/END” barcode again.
DEFAULT SETTING FOR THIS FEATURE: 20 milliseconds (02)
Set ERI Timeout
14
MagellanTM 1100i
LED and Beeper Indicators
Good Read: When to Indicate
This feature specifies when the scanner will provide indication (beep and/or flash its green
LED) upon successfully reading a barcode. Choices are:
•
Good Read = Indicate after decode
•
Good Read = Indicate after transmit
•
Good Read = Indicate after CTS goes inactive, then active
This option (Indicate after CTS goes inactive,
then active), which uses CTS, is only valid for
RS-232 interfaces.
NOTE
START / END
PROGRAMMING BARCODES
After Decode
DEFAULT
After Transmit
³
After CTS goes inactive, then active
Product Reference Guide
15
General Features
Good Read Beep Control
This feature enables/disables the scanner’s ability to beep upon a successful decode of a barcode.
START / END
PROGRAMMING BARCODES
Disable
Enable
DEFAULT
Good Read Beep Frequency
Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.)
START / END
PROGRAMMING BARCODES
Low
Medium
DEFAULT
High
16
MagellanTM 1100i
LED and Beeper Indicators
Good Read Beep Length
Specifies the duration of a good read beep.
START / END
PROGRAMMING BARCODES
60msec
80msec
DEFAULT
100msec
120msec
140msec
160msec
180msec
200msec
Product Reference Guide
17
General Features
Good Read Beep Volume
Selects the beeper volume (loudness) upon a good read beep. There are three selectable volume levels.
START / END
PROGRAMMING BARCODES
Low
Medium
High
DEFAULT
Green Spot
This feature enables / disables the green spot activation when good read is activated.
START / END
PROGRAMMING BARCODES
Disable
DEFAULT
Enable
18
MagellanTM 1100i
LED and Beeper Indicators
Aiming Pointer Settings
Enabes/disables Aiming Pointer for all symbologies.
START / END
PROGRAMMING BARCODES
Disable
DEFAULT
Enable
Product Reference Guide
19
General Features
Scanning Features
Targeted Scanning Mode
Upon pressing the button, the scanner will project an aiming pattern to assist in centering
over the barcode. Scanning then takes place as soon as the button is released.
NOTE
When add-ons are enabled and a barcode
is being read while in Targeted Mode,
position the pointer at or near the end of
the base label to ensure the scanner will
read both the base and add-on label.
Targeted Scanning Mode will read barcodes in any orientation.
The scanner will return to full pattern
Omni-directional Mode after Target Mode
Active Time has elapsed.
Configuration options for Targeted Scanning Mode are:
•
Target Mode Active Time
•
Target Mode Linger Time
Target Mode Active Time
Specifies the time duration the scanner attempts to decode labels while in the targeted mode
of operation.
START / END
PROGRAMMING BARCODES
Extra Short Duration
Short Duration
Medium Duration
DEFAULT
Long Duration
20
MagellanTM 1100i
Scanning Features
Target Mode Linger Time
Specifies the time duration the scanner remains in the targeted mode of operation after reading a barcode before reverting to Omni-directional Mode.
START / END
PROGRAMMING BARCODES
Short Duration
Medium Duration
DEFAULT
Long Duration
Product Reference Guide
21
General Features
Wake Up Intensity
This feature indicates the percentage of ambient light change which will trigger the scanner
to wake up from Sleep Mode. Lower settings provide greater sensitivity. The seelectable
range for this setting is 5% to 15%.
START / END
PROGRAMMING BARCODES
5%
6%
7%
8%
9%
10%
DEFAULT
11%
12%
22
MagellanTM 1100i
Image Capture
Wake Up Intensity — cont.
START / END
PROGRAMMING BARCODES
13%
14%
15%
Image Capture
This function is ONLY available for scanners having a button.
Image capture requires that the scanner use the Standard RS232 or USB COM interface ONLY.
NOTE
The scanner reverts to default reading mode after image capture
and transfer.
How to Capture an Image
To initiate an Image Capture, scan the IMAGE CAPTURE label below, and press the button.
A targeting “pointer” will be illuminated while the button is pressed.
Upon release of the button, the image is captured and transmitted to the host. If the button is
not pushed within 30 seconds, the scanner will return to barcode reading (scanning) mode.
By default, images are captured as 752 x 480 JPEG format with a minimum compression
ratio, and are displayed via the host application software.
IMAGE CAPTURE
Product Reference Guide
23
General Features
Image Compression
Specifies the starting image compression factor for JPEG images. A higher number specifies
a higher quality image with less compression than a relative lower number for the same
image.
A value of 100 means minimal compression. A value of 1 means maximum compression at
a loss of quality. Follow these steps to program this feature:
1. Scan the START barcode.
2. Scan the Set Image Compression barcode.
3. Turn to Alpha-Numeric Pad and scan the two digits (zero-padded) representing the
desired compression. The configurable range is 01-0x64 by increments of 01.
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Image Compression
DEFAULT SETTING IS
100 (minimal compression — higher quality)
Image Size
Specifies the size of the image capture. Choices are:
•
WVGA
•
VGA
START / END
PROGRAMMING BARCODES
Image Size = WVGA
DEFAULT
Image Size = VGA
24
MagellanTM 1100i
Image Capture
Image Brightness
This feature sets the image brightness value. Follow these instructions to configure this feature:
1. Scan the START barcode.
2. Scan the Set Image Brightness barcode.
3. Turn to Alpha-Numeric Pad and scan the two digits (zero-padded) representing the
desired brightness in decimal notation. The configurable range is 01-0x0A by increments of 01.
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Image Brightness
DEFAULT SETTING FOR THIS FEATURE: 09
Image Contrast
This feature sets the image contrast value. Follow these instructions to configure this feature:
1. Scan the START barcode.
2. Scan the Set Image Contrast barcode.
3. Turn to Alpha-Numeric Pad and scan the two digits (zero-padded) representing the
desired contrast in decimal notation. The configurable range is 01-0x0A by increments
of 01.
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Image Contrast
DEFAULT SETTING FOR THIS FEATURE: 09
Product Reference Guide
25
General Features
Cell Phone Mode
Cell Phone Mode enables the scanner to read barcodes on a cell phone display.
Cell Phone Mode Enable
Enables/disables Cell Phone Mode.
START / END
PROGRAMMING BARCODES
Cell Phone Mode = Disable
DEFAULT
Cell Phone Mode = Enable
26
MagellanTM 1100i
Cell Phone Mode
Cell Phone Detection Sensitivity
These settings control various pixel characteristics in order to optimize cell phone detection.
Follow these instructions to configure this feature:
1. Determine which sensitivity level is desired (high, medium or low).
2. Scan the START barcode to place the scanner in Programming Mode.
3. Scan the three barcodes for the detection sensitivity desired.
Unlike typical feature settings, Cell Phone Detection Sensitivity
requires the scanning of THREE barcodes to set the level. For
example, to set a high detection sensitivity level, scan barcodes
HIGH #1, HIGH #2 and HIGH #3.
NOTE
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Cell Phone Detection Sensitivity = HIGH
HIGH #1
HIGH #2
HIGH #3
Product Reference Guide
27
General Features
Cell Phone Detection Sensitivity — continued
START / END
PROGRAMMING BARCODES
Cell Phone Detection Sensitivity = MEDIUM
[This is the DEFAULT setting]
MEDIUM #1
MEDIUM #2
MEDIUM #3
Cell Phone Detection Sensitivity = LOW
LOW #1
LOW #2
LOW #3
28
MagellanTM 1100i
Cell Phone Mode
Cell Phone in Target Mode
This feature sets the reader’s Cell Phone Mode when it is in Target Mode:
This feature is only available when Cell Phone Mode is enabled.
NOTE
No Cell Phone Mode — Will not read cell phone labels when in Target Mode.
Auto Detection Cell Phone Mode — Automatically detects cell phone labels and shifts to
Cell Phone Mode when in Target Mode.
Always Enter Cell Phone Mode — The reader will always enter Cell Phone Mode when-
ever it is in Target Mode.
Follow these instructions to configure this feature:
1. Determine which mode is desired from the selections above.
2. Scan the START barcode to place the scanner in Programming Mode.
3. Scan the two barcodes which configure the desired mode.
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Cell Phone in Target Mode = No Cell Phone Mode
[This is the DEFAULT setting]
No Cell Phone Mode #1
No Cell Phone Mode #2
Product Reference Guide
29
General Features
Cell Phone in Target Mode — continued
START / END
PROGRAMMING BARCODES
Cell Phone in Target Mode = Auto Detection Cell Phone Mode
Auto Detection Cell Phone Mode #1
Auto Detection Cell Phone Mode #2
Cell Phone in Target Mode = Always Enter Cell Phone Mode
Always Enter Cell Phone Mode #1
Always Enter Cell Phone Mode #2
30
MagellanTM 1100i
Chapter 3
Interface Related Features
At the time of this writing, the reader supports the interfaces listed in Table 3-1. Select the
desired interface type from the table, then reference the page number given for the customizable features section associated with each interface. See Table 3-2 for a description of each
Keyboard Wedge interface type (A through Y as listed).
Table 3-1. Interfaces Supported
RS-232
Page Keyboard Wedge
3-34
RS-232 Standard
3-33
Keyboard Wedge Aa
3-34
RS-232 Wincor-Nixdorf
3-33
Keyboard Wedge Ba
3-34
Keyboard Wedge Ca
3-34
IBM
IBM 4683 Port 5B
3-33
Keyboard Wedge Da
3-34
IBM 4683 Port 9B
3-33
Keyboard Wedge Ea
3-34
IBM 4683 Port 17
3-33
Keyboard Wedge Fa
3-34
Keyboard Wedge Ga
3-34
USB
USB-OEM
3-33
Keyboard Wedge Ha
3-34
USB Keyboard
3-33
Keyboard Wedge Ia
3-34
USB COM Interface
3-33
Keyboard Wedge Ja
3-34
a. Consult Table 3-2 for more information regarding keyboard interface
types.
The correct interface cable is included for
the reader interface type you ordered.
NOTE
Product Reference Guide
31
Interface Related Features
Table 3-2. Keyboard Wedge Interface Reference
I/F
PCs Supported
Type
A
PC/XT w/Alternate Key Encoding
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/
B
Alternate Key Encoding
C
PS/2 25 and 30 w/Alternate Key Encoding
D
PC/XT w/Standard Key Encoding
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/
E
Standard Key Encoding
F
PS/2 25 and 30 w/Standard Key Encoding
G
IBM 3xxx w/122 keyboard
H
IBM 3xxx w/102 keyboard
I
PS/55 5530T w/104 keyboard
J
NEC 9801
NOTE
32
Reference Appendix E, Keyboard Function Key
Mappings for more information about keyboards.
MagellanTM 1100i
Interface Selection
Interface Selection
START / END
PROGRAMMING BARCODES
RS-232 Standard
RS-232 Wincor-Nixdorf
IBM 4683 Port 5B
IBM 4683 Port 9B
IBM 4683 Port 17
USB-OEM
USB Keyboard
USB COM Interface
Product Reference Guide
33
Interface Related Features
Interface Selection — cont.
START / END
PROGRAMMING BARCODES
Keyboard Wedge A
Keyboard Wedge B
Keyboard Wedge C
Keyboard Wedge D
Keyboard Wedge E
Keyboard Wedge F
\
Keyboard Wedge G
Keyboard Wedge H
³
0 0 0 1 3 2
Keyboard Wedge I
Keyboard Wedge J
34
MagellanTM 1100i
Interface Features
Interface Features
Obey/Ignore Host Commands
When set to ignore host commands, the scanner will ignore all host commands except for the
minimum set necessary to keep the interface active and transmit labels For normal operation
of the interface, select Obey Host Commands.
START / END
PROGRAMMING BARCODES
Obey Host Commands
DEFAULT
Ignore Host Commands
Product Reference Guide
35
Interface Related Features
Interface Features — cont.
Host Transmission Buffers
Specifies the number of host transmission(s) that may be buffered. By buffering data from a
barcode, the scanner can continue to read a new barcode while the old one is being transmitted to the host. Selecting BUFFERS = 1 means that the first barcode must be transmitted
before a new one can be read. A selection of BUFFERS = 2 means that a new barcode can be
read while data from the first barcode is transmitted.

When a DISABLE SCANNER command is received from the host, the scanner will continue to transmit all data that is buffered.
START / END
PROGRAMMING BARCODES
Host Transmission Buffers = 1
Host Transmission Buffers = 2
DEFAULT
36
MagellanTM 1100i
Interface Features
RS-232 Interface Features
START / END
PROGRAMMING BARCODES
1200 Baud
2400 Baud
4800 Baud
9600 Baud
DEFAULT
19200 Baud
38400 Baud
57600 Baud
115200 Baud
Product Reference Guide
37
Interface Related Features
RS-232 Interface Features — cont.
START / END
PROGRAMMING BARCODES
7 Data Bits
8 Data Bits
DEFAULT
1 Stop Bit
DEFAULT
2 Stop Bits
Parity = None
DEFAULT
Parity = Even
Parity = Odd
38
MagellanTM 1100i
Interface Features
RS-232 Interface Features — cont.
Hardware Flow Control
Disable Hardware Control— The scanner transmits to the host regardless of any activity
on the CTS line.
Enable CTS Flow Control— The CTS signal controls transmission of data to the host.
Enable CTS Scan Control— The CTS line must be active for the scanner to read and trans-
mit data. While the CTS line is inactive, the scanner remains in a host-disabled state; following a successful label transmission, the CTS signal must transition to inactive and then to
active to enable scanning for the next label.
START / END
PROGRAMMING BARCODES
Disable Hardware Control
DEFAULT
Enable CTS Flow Control
Enable CTS Scan Control
Product Reference Guide
39
Interface Related Features
RS-232 Interface Features — cont.
Intercharacter Delay
This delay is inserted after each data character transmitted. If the transmission speed is too
high, the system may not be able to receive all characters. You may need to adjust the delay
to make the system work properly.
START / END
PROGRAMMING BARCODES
Inter-Char Delay = No Delay
DEFAULT
Interchar Delay = 10 msec
Interchar Delay = 20 msec
Interchar Delay = 30 msec
Interchar Delay = 40 msec
Interchar Delay = 50 msec
Interchar Delay = 60 msec
Interchar Delay = 70 msec
40
MagellanTM 1100i
Interface Features
Intercharacter Delay — cont.
START / END
PROGRAMMING BARCODES
Interchar Delay = 80 msec
Interchar Delay = 90 msec
Software Flow Control
Disables/Enables software control using XON/XOFF characters.
START / END
PROGRAMMING BARCODES
Disable Software Flow Control
DEFAULT
Enable Software Flow Control
Product Reference Guide
41
Interface Related Features
RS-232 Interface Features — cont.
Host Echo Quiet Interval
This setting specifies the time interval of RS-232 channel inactivity which must transpire
before the scanner will break the host echo loop to transmit the barcode data that has just
been scanned to the host.
START / END
PROGRAMMING BARCODES
Host Echo Quiet Interval = 0msec
Host Echo Quiet Interval = 10msec
DEFAULT
Host Echo Quiet Interval = 20msec
Host Echo Quiet Interval = 30msec
Host Echo Quiet Interval = 40msec
Host Echo Quiet Interval = 50msec
Host Echo Quiet Interval = 60msec
Host Echo Quiet Interval = 70msec
42
MagellanTM 1100i
Interface Features
Host Echo Quiet Interval — cont.
START / END
PROGRAMMING BARCODES
Host Echo Quiet Interval = 80msec
Host Echo Quiet Interval = 90msec
Host Echo Quiet Interval = 100msec
Signal Voltage: Normal/TTL
Specifies whether the RS-232 interface provides TTL levels on the output pins TxD and
RTS.
START / END
PROGRAMMING BARCODES
Signal Voltage: Normal RS-232
DEFAULT
Signal Voltage: TTL
Product Reference Guide
43
Interface Related Features
Beep on ASCII BEL
Enables/disables ability of scanner to beep (sound a good read tone) on receiving an ASCII
BEL (07 hex).
START / END
PROGRAMMING BARCODES
Enable Beep on ASCII BEL
DEFAULT
Disable Beep on ASCII BEL
Beep on Not on File
Select for the host to beep (or not) when a not-on-file (host command) condition is detected
by the host.
START / END
PROGRAMMING BARCODES
Disable Beep on Not On File
Enable Beep on Not On File
DEFAULT
44
MagellanTM 1100i
Interface Features
ACK NAK Options
This enables/disables the ability of the scanner to support the RS-232 ACK/NAK protocol.
When configured, the scanner and/or host sends an “ACK” when it receives data properly,
and sends “NAK” when the data is in error. Selections for this option are:
•
Disable
•
Enable for label transmission — the scanner expects an ACK/NAK response from the
host when a label is sent
•
Enable for host-command acknowledge — the scanner will respond with ACK/NAK
when the host sends a command
•
Enable for label transmission and host-command acknowledge
START / END
PROGRAMMING BARCODES
Disable ACK NAK
DEFAULT
Enable ACK NAK for Transmission
Enable ACK NAK for host command acknowledge
Enable ACK NAK for transmission and host command
Product Reference Guide
45
Interface Related Features
RS-232 Interface Features — cont. — cont.
ACK Character
START / END
PROGRAMMING BARCODES
Sets the ACK character from the set of ASCII characters or any decimal value from 000 to 255. Pad entries
of less than three digits with zeros, as in “005”. To configure this feature, scan the “START/END” barcode
above to place the unit in Programming Mode, then the “Set ACK Character,” followed by the digits from the
Alphanumeric table in Appendix C, Alpha-Numeric Pad representing your desired character. Exit programming
mode by again scanning the “START/END” barcode above.
DEFAULT SETTING FOR THIS FEATURE: 006
Set ACK Character
NAK Character
START / END
PROGRAMMING BARCODES
Sets the NAK character from the set of ASCII characters or any decimal value from 000 to 255. Pad entries
of less than three digits with zeros, as in “005”. To configure this feature, scan the “START/END” barcode
above to place the unit in Programming Mode, then the “Set NAK Character,” followed by the digits from the
Alphanumeric table in Appendix C, Alpha-Numeric Pad representing your desired character. Exit programming
mode by again scanning the “START/END” barcode above.
DEFAULT SETTING FOR THIS FEATURE: 021
Set NAK Character
46
MagellanTM 1100i
Interface Features
RS-232 Interface Features — cont.
Retry on ACK NAK Timeout
Enables/disables retry after the configurable ACK NAK Timeout Value (set in the following
feature) has expired.
START / END
PROGRAMMING BARCODES
Disable Retry on ACK NAK Timeout
Enable Retry on ACK NAK Timeout
DEFAULT
ACK NAK Timeout Value
START / END
PROGRAMMING BARCODES
This item specifies the time the scanner will wait for an ACK character from the host following a label transmission.
000 = Infinite timeout
001 - 075 = Timeout in 200-millisecond increments
To configure this feature, scan the “START/END” barcode above to place the unit in Programming Mode,
then the “Set ACK NAK Timeout Value,” followed by the three digits (zero padded) from the Alphanumeric
table in Appendix C, Alpha-Numeric Pad representing your desired value. Exit programming mode by again
scanning the “START/END” barcode above.
DEFAULT SETTING FOR THIS FEATURE: 001 (200 msec)
Set ACK NAK Timeout Value
Product Reference Guide
47
Interface Related Features
RS-232 Interface Features — cont.
ACK NAK Retry Count
START / END
PROGRAMMING BARCODES
This feature sets the number of times for the scanner to retry a label transmission under a retry condition.
000 = No retry
001 - 254 = Retry for the specified number of times
255 = Retry forever
To configure this feature, scan the “START/END” barcode above to place the unit in Programming Mode,
then the “Set ACK NAK Retry Count,” followed by the three digits (zero padded) from the Alphanumeric table
in Appendix C, Alpha-Numeric Pad representing your desired retry count. Exit programming mode by again
scanning the “START/END” barcode above
DEFAULT SETTING FOR THIS FEATURE: 003
Set ACK NAK Timeout Value
48
MagellanTM 1100i
Interface Features
RS-232 Interface Features — cont.
ACK NAK Error Handling
This item specifies the method the scanner will use to handle errors detected while waiting
to receive the ACK character from the host. Errors include unrecognized host commands
and communication errors such as parity or framing errors. Choices are:
00 = Ignore errors detected (recommended setting)
01 = Process error as valid ACK character (risk of lost label data)
02 = Process error as valid NAK character (risk of duplicate label data)
START / END
PROGRAMMING BARCODES
Ignore Errors Detected
DEFAULT
Process error as valid ACK character
Process error as valid NAK character
Product Reference Guide
49
Interface Related Features
RS-232 Interface Features — cont.
Transmission Failure Indication
Enables/disables bad-label indication upon transmission failure.
START / END
PROGRAMMING BARCODES
Disable Transmission Error Indication
Enable Transmission Error Indication
DEFAULT
USB-OEM Interface Features
USB-OEM Device usage
The USB-OEM protocol allows for the scanner to be identified as one of two different types
of barcode scanners. Depending on what other scanners you may already have connected to
a USB-OEM POS, you may need to change this setting to enable all devices to communicate. Options are:
•
Table Top Scanner
•
Handheld Scanner
START / END
PROGRAMMING BARCODES
Configure as Table Top Scanner
DEFAULT
Configure as Handheld Scanner
50
MagellanTM 1100i
Interface Features
IBM
IBM Transmit Labels in Code 39 Format
This feature enables/disables scanner's ability to set a symbology identifier for a specified
label to Code 39 before transmitting that label data to an IBM host. This applies to: Code
128, Codabar and Code 93 for USB-OEM; Code 128, Codabar and Code 93 for IBM Port
5B; and Codabar and Code 93 for IBM Port 9B.
START / END
PROGRAMMING BARCODES
Disable Convert to Code 39
DEFAULT
Enable Convert to Code 39
Product Reference Guide
51
Interface Related Features
Keyboard Wedge
and
USB Keyboard
As a keyboard interface, the scanner supports most popular PCs and IBM terminals. The
installation of the wedge is a fairly simple process that doesn’t require any changes of software or hardware.
All of the options in this section apply to the
Keyboard Wedge, however, only some
apply to USB Keyboard.
NOTE
Keyboard Layout
The Keyboard Layout option supports many countries. For details about Keyboard Layout,
please refer to your operating system manual.
START / END
PROGRAMMING BARCODES
USA
DEFAULT
Belgium
Britain
Denmark
France
Germany
52
MagellanTM 1100i
Interface Features
Keyboard Wedge — cont.
START / END
PROGRAMMING BARCODES
Italy
Norway
Portugal
Spain
Sweden
Switzerland
Japan 106 Key
Hungary
Czech Republic
Product Reference Guide
53
Interface Related Features
Keyboard Wedge — cont.
START / END
PROGRAMMING BARCODES
Slovakia
Romania
Croatia
Poland
Caps Lock State
Specifies the format in which the scanner sends character data.
START / END
PROGRAMMING BARCODES
Disable Caps Lock
DEFAULT
Caps Lock “ON”
Shift Lock “ON”
54
MagellanTM 1100i
Interface Features
Keyboard Wedge — cont.
Power-On Simulation
This feature does not apply to the USB Keyboard interface.
NOTE
All PCs check the keyboard status during the power-on Selftest. It is recommended that you
enable this function if you are working without a keyboard installation. It simulates keyboard timing and passes the keyboard status to the PC during power-on.
START / END
PROGRAMMING BARCODES
Disable Power-on Simulation
DEFAULT
Enable Power-on Simulation
Product Reference Guide
55
Interface Related Features
Control Characters
Specifies how the scanner transmits ASCII control characters to the host. Choices are:
•
Disable Control Characters
•
Enable transmission of control characters to host
•
Send characters between 00H and 1FH according to a special function-key mapping
table. (This is used to send keys that are not in the normal ASCII set; a unique set is
provided for each available scancode set. Reference Appendix E, Keyboard Function Key
Mappings.)
START / END
PROGRAMMING BARCODES
Disable Control Characters
DEFAULT
Enable Transmission of Control Characters
Enable Function Key Mapping
56
MagellanTM 1100i
Interface Features
Keyboard Wedge — cont.
Wedge Quiet Interval
This feature does not apply to the USB Keyboard interface.
NOTE
Quiet Interval is the amount of time to look for keyboard activity before the scanner breaks
the keyboard connection in order to transmit data to the host.
START / END
PROGRAMMING BARCODES
Selectable from 001 to 100 in 10 msec increments. To configure this feature, scan the “START/END” bar
code above to place the unit in Programming Mode, then the Set Wedge Quiet Interval bar code followed by
the three digits (zero padded) from the Alphanumeric table in Appendix C, Alpha-Numeric Pad representing
your desired length. Exit programming mode by again scanning the “START/END” bar code above.
DEFAULT SETTING FOR THIS FEATURE:
010 (100 msec)
Set Wedge Quiet Interval
Product Reference Guide
57
Interface Related Features
Keyboard Wedge — cont.
Intercharacter Delay
START / END
PROGRAMMING BARCODES
One-half of the delay specified below is inserted between scancodes within each character. If the transmission speed is too high, the system may not be able to receive all characters. You may need to adjust the
delay to make the system work properly. Selectable from 00 to 99 in 10msec increments.
To configure this feature, scan the “START/END” barcode above to place the unit in Programming Mode,
then the “Set Intercharacter Delay,” followed by the three digits (zero padded) from the Alphanumeric table in
Appendix C, Alpha-Numeric Pad representing your desired length. Exit programming mode by again scanning
the “START/END” barcode above/
DEFAULT SETTING FOR THIS FEATURE:
00 (No Delay)
Set Intercharacter Delay
USB COM Interface Set-up
This interface uses the Microsoft Windows USB COM driver. Before plugging your reader
into the host PC, please ensure you have already copied the DLS_EUG_CDC_ACM.inf file
provided by Datalogic to your PC and the reader’s interface is set to USB COM.
1. When you first plug the scanner into the PC, Windows will bring up the “Found New
Hardware Wizard.” Select “Install from a list” and click on “Next.”
2. Click on “Include this location in the search” and enter the path where the file
DLS_EUG_CDC_ACM.inf file is stored. Click on “Next.”
3. If a message appears that says the software has not passed Windows logo testing, press
“Continue” anyway.
4. Click on “Finish.”
5. Once the install is complete, reboot the PC.
58
MagellanTM 1100i
Chapter 4
Data Editing
Data Editing Overview
It is not recommended to use these features
with IBM interfaces.
CAUTION
When a barcode is scanned, additional information can be sent to the host computer along
with the barcode data. This combination of barcode data and supplementary user-defined
data is called a “message string.” The features in this chapter can be used to build specific
user-defined data into a message string.
There are several types of selectable data characters that can be sent before and after scanned
data. You can specify if they should be sent with all symbologies, or only with specific symbologies. Figure 4-1 shows the available elements you can add to a message string:
Figure 4-1. Breakdown of a Message String
Label ID Transmission:
Enable this option to
transmit the Label ID you
configure for the scanned
symbology.
OR...
Prefix
Label ID
AIM ID
Bar Code Data
Label ID
Suffix
AIM ID: This function is used to identify and display the
common label identifier for its symbology. When enabled,
this ID code will be transmitted before the scanned bar
code data.
00 - 20 Characters (ASCII)
Please Keep In Mind...
•
Modifying a message string is not a mandatory requirement. Data editing is sophisticated feature allowing highly customizable output for advanced users. Factory default
settings for data editing is typically set to NONE.
•
A prefix or suffix may be applied (reference the Symbologies chapter for these settings)
across all symbologies (set via the Global features in this chapter).
•
You can add any character from the ASCII Chart (from 00-7F) on the inside back cover
of this manual as a prefix, suffix or Label ID.
•
Enter prefixes and suffixes in the order in which you want them to appear on the output.
Product Reference Guide
59
Data Editing
Global Prefix/Suffix
Up to 20 ASCII characters may be added as a prefix (in a position before the barcode data)
and/or as a suffix (in a position following the barcode data) as indicated in Figure 4-2.
Figure 4-2. Prefix and Suffix Positions
OR...
Prefix
Label ID
AIM ID
Bar Code Data
Label ID
Suffix
00 - 20 Characters (ASCII)
AND
OR
Example: Setting a Prefix
In this example, we’ll set a prefix for all symbologies.
1. Determine which ASCII character(s) are to be added to scanned barcode data. In this
example, we’ll add a dollar sign (‘$’) as a prefix.
2. Scan the START barcode.
3. Scan the SET PREFIX barcode.
4. Reference the ASCII Chart on the inside back cover of this manual, to find the hex value
assigned to the desired character. The corresponding hex number for the ‘$’ character
is 24. To enter this selection code, scan the ‘2’ and ‘4’ barcodes from Appendix C, AlphaNumeric Pad.
5. Scan the END barcode once to finish the string, then scan END again to exit Programming Mode.
If all 20 characters will be used in the prefix or
suffix, do not scan the END barcode to finish
the string. It is done automatically.
NOTE
6. The resulting message string would appear as follows:
Scanned barcode data:12345
Resulting message string output: $12345
60
MagellanTM 1100i
Global Prefix/Suffix
Global Prefix/Suffix — cont.
START / END
PROGRAMMING BARCODES
Sets up to 20 characters each from the set of ASCII characters or any hex value from 00 to 7F. To configure
this feature, scan the “START/END” barcode above to place the unit in Programming Mode, then the “Set
Prefix” or “Set Suffix,” followed by the digits from the Alphanumeric table in Appendix C, Alpha-Numeric Pad
representing your desired character(s). Reference the section, "Example: Setting a Prefix", for more information. Exit programming mode by scanning the “START/END” barcode again (scan “START/END” twice if less
than 20 characters have been selected).
DEFAULT SETTING PREFIX: 00 (None)
DEFAULT SETTING SUFFIX: 0D (CR)
Set Prefix
Set Suffix
Product Reference Guide
61
Data Editing
AIM ID
AIM (Automatic Identification Manufacturers) label identifiers are assigned from a globally
standardized list — as opposed to custom label ID characters you select yourself — and can
be included with scanned barcode data. AIM label identifiers consist of three characters as
follows:
•
A close brace character (ASCII ‘]’), followed by...
•
A code character (see the table below), followed by...
•
A modifier character (the modifier character is symbol dependent)
SYMBOLOGY
CHA
R
CHA
R
SYMBOLOGY
UPC/EAN
E
Code 128/EAN 128
C
Code 39
A
MSI/Plessey
M
Codabar
F
RSS (GS1 Omnidirectional, GS1 Expanded)
e
Interleaved 2 of 5
I
Standard 2 of 5
S
Code 93
G
ISBN
Xa
a. ISBN (X with a 0 modifier character)
Figure 4-3. AIM ID
Prefix
Label ID
AIM ID
Bar Code Data
Label ID
Suffix
START / END
PROGRAMMING BARCODES
Disable AIM ID
DEFAULT
Enable AIM ID
62
MagellanTM 1100i
Label ID
Label ID
A Label ID is used to identify a barcode (symbology) type. See Appendix D, Default Settings,
for a listing for common symbologies. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides
options for configuring custom Label IDs individually per symbology. If you wish to program the scanner to always include an industry standard label identifier for ALL symbology
types, see the previous feature, AIM ID.
The Label ID is a customizable code of up to three ASCII characters (each of which are 007F) followed by a control character (00-01), This control character, when set to zero, does
nothing. When set to one, it appends the symbology’s AIM ID to the Label ID.
NOTE
When the control character is set to 01 for
UPC-A and UPC-E, it expands the label to
EAN-13 and thus follows the EAN-13 Label ID
settings.
To configure a Label ID:
1. Scan the START barcode.
2. Select Label ID position as either BEFORE or AFTER by scanning the appropriate
barcode.
3. Scan a barcode to select the symbology for which you wish to configure a custom
Label ID.
4. Determine the desired character(s) (you may choose up to three) which will represent
the Label ID for the selected symbology. Next, turn to the ASCII Chart on the inside
back cover of this manual and find the equivalent hex digits associated with your
choice of Label ID. For example, if you wish to select an equal sign (=) as a Label ID,
the chart indicates its associated hex characters as 3D.
5. Turn to Appendix C, Alpha-Numeric Pad and scan the barcodes representing the hex characters determined in the previous step. For example, to make an equal sign (=), scan
‘3’ and ‘D’ followed by ‘0’ six times. Since this is a three-character buffer, ‘00’ is
scanned for character two, ‘00’ for character three and ‘00’ for the control character.
(‘00’ indicates no character.)
6. Scan the END barcode to exit programming mode.
Figure 4-4. Label ID Position Options
Prefix
Label ID
Aim ID
Bar Code Data
Label ID
Suffix
OR
Product Reference Guide
63
Data Editing
Label ID — cont.
START / END
PROGRAMMING BARCODES
Label ID Transmission: Disable
Label ID Position: Before Barcode Data
DEFAULT
Label ID Position: After Barcode Data
Set UPC-A Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: A (41 hex)
Set UPC-A w/P2 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: A (41 hex)
Set UPC-A w/P5 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: A (41 hex)
Set UPC-A w/C128 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: A (41 hex)
Set UPC-E Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: E (45 hex)
64
MagellanTM 1100i
Label ID
Label ID — cont.
START / END
PROGRAMMING BARCODES
Set UPC-E w/P2 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: E (45 hex)
Set UPC-E w/P5 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: E (45 hex)
Set UPC-E w/C128 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: E (45 hex)
Set EAN-8 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: FF (4646 hex)
Set EAN-8 w/P2 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: FF (4646 hex)
Set EAN-8 w/P5 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: FF (4646 hex)
Set EAN-8 w/C128 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: FF (4646 hex)
Set EAN-13 Label ID Character(s)
³ 0FOR
0 THIS
2 FEATURE:
7
DEFAULT SETTING
F (46 hex)
Product Reference Guide
65
Data Editing
Label ID — cont.
START / END
PROGRAMMING BARCODES
Set EAN-13 w/P2 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: F (46 hex)
Set EAN-13 w/P5 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: F (46 hex)
Set EAN-13 w/C128 Addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: F (46 hex)
Set ISBN Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: I (49 hex)
Set IATA Label ID Character(s)
³ FOR
0 3THIS
4 FEATURE:
C
DEFAULT SETTING
IA (4941 hex)
Set GTIN Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: G (47 hex)
Set GTIN w/P2 addon Label ID Character(s)
³ FOR
0 THIS6 FEATURE:
1
DEFAULT SETTING
G2 (4732 hex)
Set GTIN w/P5 addon Label ID Character(s)
³ FOR
0 5THIS6 FEATURE:
2
DEFAULT SETTING
G5 (4735 hex)
66
MagellanTM 1100i
Label ID
Label ID — cont.
START / END
PROGRAMMING BARCODES
Set GTIN w/C128 addon Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: G8 (4738 hex)
Set GS1 Omnidirectional Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: R4 (5234 hex)
Set GS1 Expanded Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: RX (5258 hex)
Set Code GS1 DataBar Limited Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: * (524C0000 hex)
Set Code 39 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: * (2A hex)
Set Pharmacode 39 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: A (41 hex)
Set Code 128 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: # (23 hex)
Set I 2 of 5 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: i (69 hex)
Product Reference Guide
67
Data Editing
Label ID — cont.
START / END
PROGRAMMING BARCODES
Set Codabar Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: % (25 hex)
Set Code 93 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: & (26 hex)
Set Code 11 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: @ (40 hex)
Set MSI/Plessey Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: @ (40 hex)
Set Std 2 of 5 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: s (73 hex)
Set EAN UCC Composite Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: 0
Set PDF 417 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: P (5000
hex)a
Set Datamatrix Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: Dm (446D hex)
a. 
Default setting exceptions for PDF 417 Label ID are as follows: Default for RS-232 WN is ‘Q’ (0x5100). Default for USB-HIDPOS is ‘P ‘ (0x5020), or ‘P-Space’.
68
MagellanTM 1100i
Label ID
Label ID — cont.
NOTE
For the 2D symbologies on this page, the
Label ID is 4 bytes. The first 3 bytes are characters for the label ID. A 00 (hex) value in the
first 3 bytes indicates the end of the label ID
characters. The 4th byte is a control byte.
The use of the control byte is as follows:
bit 0-if set to 1, the AIM Id is appended for that
label type
START / END
PROGRAMMING BARCODES
Set Micro PDF 417 Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: mP (6D500000 hex)
Set QR Code Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: QR (51520000 hex)
Set Maxicode Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: MC (4D430000 hex)
Set Aztec Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: Az (417A0000 hex)
Set GS1 DataBar Omnidirectional 2D Composite
Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: R4 (52340000 hex)
Set GS1 DataBar Limited 2D Composite
Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: RL (524C0000 hex)
Set GS1 DataBar Expanded 2D Composite
Label ID Character(s)
DEFAULT SETTING FOR THIS FEATURE: RX (52340000 hex)
Product Reference Guide
69
Data Editing
Case Conversion
This feature can convert scanned barcode data to either all lower case (a through z) or all
upper case (A through Z) characters.
Case conversion affects ONLY scanned barcode data, and does not affect Label ID, Prefix, Suffix, or other appended data.
NOTE
START / END
PROGRAMMING BARCODES
Disable
DEFAULT
Convert to Upper Case
Convert to Lower Case
70
MagellanTM 1100i
Character Conversion
Character Conversion
Character conversion is an eight byte configuration item. The eight bytes are 4 character
pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted. The second character in the pair is the character to convert to. If
the character to convert in a pair is FF, then no conversion is done.
For example, if you have the character conversion configuration item set to the following:
41423132FFFFFFFF
The first pair is 4142 or AB (41 hex is an ASCII capital A, 42 hex is an ASCII capital B)
and the second pair is 3132 or 12 (31 hex is an ASCII 1, 32 is an ASCII 2). The other two
pairs are FFFF and FFFF.
With the label, AG15TA81, it would look as follows after the character conversion:
BG25TB82.
The A characters were converted to the B character and the 1 characters were converted to
the numeral 2 character. Nothing is done with the last two character pairs, since they are all
FF.
To set Character Conversion:
1. Scan the START/END barcode.
2. Scan the Character Conversion barcode.
3. Determine the desired string. Up to sixteen positions can be determined as in the above
example. Next, turn to the ASCII Chart on the inside back cover of this manual and find
the equivalent hex digits needed to fulfill the string.
The positions not used must be filled with the
character ‘F’.
NOTE
4. Turn to Appendix C, Alpha-Numeric Pad and scan the barcodes representing the hex characters determined in the previous step. When the last character is scanned, the scanner
will sound a triple beep.
5. Scan the START/END barcode to exit Programming Mode.
START / END
PROGRAMMING BARCODES
Character Conversion
DEFAULT SETTING FOR THIS FEATURE:
FFFFFFFFFFFFFFFF hex (no conversion)
Product Reference Guide
71
Data Editing
NOTES
72
MagellanTM 1100i
Chapter 5
Symbologies
The scanner supports the following symbologies (barcode types). Options for each symbology
are included in this chapter.
• UPC-A
• Code 32 Italian
Pharmacode
• UPC-E
• Code 128
• EAN-13
• Interleaved 2 of 5
• EAN-8
• Codabar
• GS1 DataBar Omnidirectional /
Stacked Omnidirectional
• Code 93
• GS1 DataBar Expanded /
Expanded Stacked
• MSI/Plessey
• GS1 DataBar Limited
• Standard 2 of 5
• Code 39
Factory Defaults— for the standard RS-232 interface are indicated in bold text throughout
this section. Reference Appendix D, Default Settings for default exceptions for your interface.
UPC-A
Disable/Enable UPC-A
When disabled, the scanner will not read UPC-A barcodes.
START / END
PROGRAMMING BARCODES
Disable UPC-A
Enable UPC-A
DEFAULT
Product Reference Guide
73
Symbologies
UPC-A — continued
Check Digit Transmission
Enable this option to transmit the check digit along with UPC-A barcode data.
START / END
PROGRAMMING BARCODES
Don’t Send Check Digit
Send Check Digit
DEFAULT
Expand UPC-A to EAN-13
Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13.
START / END
PROGRAMMING BARCODES
Don’t Expand to EAN-13
DEFAULT
Expand to EAN-13
74
MagellanTM 1100i
UPC-A
UPC-A — continued
Number System Transmission
This feature enables/disables transmission of UPC-A System Number.
START / END
PROGRAMMING BARCODES
Disable Number System Transmission
Enable Number System Transmission
DEFAULT
UPC-A Minimum Reads
This feature specifies the minimum number of consecutive times a UPC-A label must be
decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
75
Symbologies
UPC-A — continued
UPC-A In-store Minimum Reads
This feature specifies the minimum number of consecutive times an in-store printed label must
be decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
76
MagellanTM 1100i
UPC-E
UPC-E
The following options apply to the UPC-E symbology.
Disable/Enable UPC-E
When disabled, the scanner will not read UPC-E barcodes.
START / END
PROGRAMMING BARCODES
Disable UPC-E
Enable UPC-E
DEFAULT
Check Digit Transmission
Enable this option to transmit the check digit along with UPC-E barcode data.
START / END
PROGRAMMING BARCODES
Don’t Send Check Digit
Send Check Digit
DEFAULT
Product Reference Guide
77
Symbologies
UPC-E — continued
Number System Digit
The Number System Digit (NSD) which is always a zero (0) in the leading position can be
optionally included (or not) with scanned barcode data.
START / END
PROGRAMMING BARCODES
Exclude Number System Digit
DEFAULT
Include Number System Digit
³
0 2
8 0 1
Expand to UPC-E to UPC-A
Enables/disables expansion of UPC-E labels to UPC-A. Selecting this feature also changes the
symbology ID to match those required for UPC-A.
START / END
PROGRAMMING BARCODES
Don’t Expand UPC-E to UPC-A
DEFAULT
Expand UPC-E to UPC-A
78
MagellanTM 1100i
UPC-E
UPC-E — continued
Expand UPC-E to EAN13
Enables/disables expansion of UPC-E labels to EAN-13. Selecting this feature also changes the
symbology ID to match those required for EAN-13.
START / END
PROGRAMMING BARCODES
Don’t Expand UPC-E to EAN-13
DEFAULT
Expand UPC-E to EAN-13
Minimum Reads
This feature specifies the minimum number of consecutive times a UPC-E label must be
decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
Minimum = 2 Reads
DEFAULT
Minimum = 3 Reads
Minimum = 4 Reads
³
Product Reference Guide
0 0 6 2 0
79
Symbologies
GTIN
The following options apply to the GTIN label data format.
Expand UPC/EAN to GTIN
When this feature is enabled, the scanner will translate UPC/EAN labels to the 14 digit GTIN
format.
START / END
PROGRAMMING BARCODES
Don’t Expand to GTIN
DEFAULT
Expand to GTIN
80
MagellanTM 1100i
EAN-13
EAN-13
The following options apply to the EAN-13 symbology.
Disable/Enable EAN-13
When disabled, the scanner will not read EAN-13 barcodes.
START / END
PROGRAMMING BARCODES
Disable EAN-13
Enable EAN-13
DEFAULT
Check Digit Transmission
Enable this option to transmit the check digit along with EAN-13 barcode data.
START / END
PROGRAMMING BARCODES
Don’t Send Check Digit
Send Check Digit
DEFAULT
Product Reference Guide
81
Symbologies
EAN-13 — continued
EAN-13 Flag 1 Character
Enables/disables transmission of an EAN/JAN13 Flag1 character.
START / END
PROGRAMMING BARCODES
Don’t Transmit EAN-13 Flag 1 Char
Transmit EAN-13 Flag 1 Char
DEFAULT
ISBN
When enabled, this feature truncates the leading three digits from labels that contain ISBN
(International Standard Book Number) and appends an ISBN check character to the end of the
label. These codes are used for books and magazines. Labels with ISBN codes start with "978".
Example:
Barcode data:
“9789572222720”
Output:
“9572222724”
START / END
PROGRAMMING BARCODES
Disable ISBN
DEFAULT
Enable ISBN
82
MagellanTM 1100i
EAN-13
EAN-13 — continued
Minimum Reads
This feature specifies the minimum number of consecutive times an EAN-13 label must be
decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
³
Product Reference Guide
0 0 6
0
83
Symbologies
EAN-8
The following options apply to the EAN-8 symbology.
Disable/Enable EAN-8
When disabled, the scanner will not read EAN-8 barcodes.
START / END
PROGRAMMING BARCODES
Disable EAN-8
Enable EAN-8
DEFAULT
Check Digit Transmission
Enable this option to transmit the check Digit along with EAN-8 barcode data.
START / END
PROGRAMMING BARCODES
Don’t Send Check Digit
Send Check Digit
DEFAULT
84
MagellanTM 1100i
EAN-8
EAN-8 — continued
Expand EAN-8 to EAN-13— Expands EAN-8 data to the EAN-13 data format. Selecting
this feature also changes the symbology ID to match those required for EAN-13.
START / END
PROGRAMMING BARCODES
Don’t Expand to EAN-13
DEFAULT
Expand to EAN-13
Minimum Reads
This feature specifies the minimum number of consecutive times an EAN-8 label must be
decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
85
Symbologies
EAN Two-Label
Enables/disables the ability of the scanner to decode EAN two-label pairs.
START / END
PROGRAMMING BARCODES
Disable EAN Two-Label
Enable EAN Two-Label
EAN Two-Label Type 1
Specifies label types and number of flag digits for EAN/JAN two-label pair 1. Options are:
•
EAN/JAN13, EAN/JAN13 - 2 flag digits each
•
EAN/JAN13 - 2 flag digits, EAN/JAN8 - 1 flag digit
•
EAN/JAN13, EAN/JAN8 - 1 flag digit each
•
Disable pairs
START / END
PROGRAMMING BARCODES
EAN Two-Label Type 1 =
EAN/JAN13, EAN/JAN13 - 2 flag digits each
DEFAULT
EAN Two-Label Type 1 =
EAN/JAN13 - 2 flag digits, EAN/JAN8 - 1 flag digit
EAN Two-Label Type 1 =
EAN/JAN13, EAN/JAN8 - 1 flag digit each
EAN Two-Label Type 1 = Disable pairs
86
MagellanTM 1100i
EAN Two-Label
EAN Two-Label — continued
EAN Two-Label Type 2
Specifies label types and number of flag digits for EAN/JAN two-label pair 2. Options are:
•
EAN/JAN13, EAN/JAN13 - 2 flag digits each
•
EAN/JAN13 - 2 flag digits, EAN/JAN8 - 1 flag digit
•
EAN/JAN13, EAN/JAN8 - 1 flag digit each
•
Disable pairs
START / END
PROGRAMMING BARCODES
EAN Two-Label Type 2 =
EAN/JAN13, EAN/JAN13 - 2 flag digits each
DEFAULT
EAN Two-Label Type 2 =
EAN/JAN13 - 2 flag digits, EAN/JAN8 - 1 flag digit
EAN Two-Label Type 2 =
EAN/JAN13, EAN/JAN8 - 1 flag digit each
EAN Two-Label Type 2 = Disable pairs
Product Reference Guide
87
Symbologies
EAN Two-Label — continued
EAN Two-Label Type 3
Specifies label types and number of flag digits for EAN/JAN two-label pair 3. Options are:
•
EAN/JAN13, EAN/JAN13 - 2 flag digits each
•
EAN/JAN13 - 2 flag digits, EAN/JAN8 - 1 flag digit
•
EAN/JAN13, EAN/JAN8 - 1 flag digit each
•
Disable pairs
START / END
PROGRAMMING BARCODES
EAN Two-Label Type 3 =
EAN/JAN13, EAN/JAN13 - 2 flag digits each
DEFAULT
EAN Two-Label Type 3 =
EAN/JAN13 - 2 flag digits, EAN/JAN8 - 1 flag digit
EAN Two-Label Type 3 =
EAN/JAN13, EAN/JAN8 - 1 flag digit each
EAN Two-Label Type 3 = Disable pairs
88
MagellanTM 1100i
EAN Two-Label
EAN Two-Label — continued
EAN Two-Label Type 4
Specifies label types and number of flag digits for EAN/JAN two-label pair 4. Options are:
•
EAN/JAN13, EAN/JAN13 - 2 flag digits each
•
EAN/JAN13 - 2 flag digits, EAN/JAN8 - 1 flag digit
•
EAN/JAN13, EAN/JAN8 - 1 flag digit each
•
Disable pairs
START / END
PROGRAMMING BARCODES
EAN Two-Label Type 4 =
EAN/JAN13, EAN/JAN13 - 2 flag digits each
EAN Two-Label Type 4 =
EAN/JAN13 - 2 flag digits, EAN/JAN8 - 1 flag digit
EAN Two-Label Type 4 =
EAN/JAN13, EAN/JAN8 - 1 flag digit each
DEFAULT
EAN Two-Label Type 4 = Disable pairs
Product Reference Guide
89
Symbologies
EAN Two-Label — continued
EAN Two-Label Combined Transmission
Enables/disables the transmitting of an EAN two label pair as one label.
START / END
PROGRAMMING BARCODES
EAN Two-Label Combined Transmission = Disable
DEFAULT
EAN Two-Label Combined Transmission = Enable
90
MagellanTM 1100i
EAN Two-Label Combined Transmission
EAN Two-Label — continued
EAN Two-Label Minimum Reads
This feature specifies the minimum consecutive decodes of an EAN two-label pair before it is
accepted as good read..
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
91
Symbologies
Price Weight Check Digit
Enables/disables calculation and verification of price/weight check digits.
Applies to all UPC-A labels with a number-system character of 2 and EAN/JAN 13 labels with a Flag1 digit of 2
NOTE
Here are the available options for this feature:
•
Disable
•
Enable 4-digit price/wt check-digit calculation
•
Enable 5-digit price/wt check-digit calculation
•
Enable European 4-digit price-weight check-digit calculation
•
Enable European 5-digit price-weight check-digit calculation
START / END
PROGRAMMING BARCODES
Price Weight Check Digit = Disable
DEFAULT
Price Weight Check Digit = Enable 4-digit price/wt
Price Weight Check Digit = Enable 5-digit price/wt
Price Weight Check Digit = Enable European 4-digit
price/wt
Price Weight Check Digit = Enable European 5-digit
price/wt
92
MagellanTM 1100i
Add-ons
Add-ons
Add-ons (or supplemental characters) are commonly added to the end of UPC/EAN barcodes.
The scanner will read the add-ons if they are enabled and in the field of view. Three add-on
types are supported: 2-digit, 5-digit and Code 128 add-ons. Supported options are:
None— This option directs the scanner to ignore add-on portion of a UPC/EAN barcode but
still read the main portion of the barcode.
2 Digits— The scanner will optionally read 2-digit add-ons with the UPC/EAN label.
5 Digits— The scanner will optionally read 5-digit add-ons with the UPC/EAN label.
Code 128 Add-on— The scanner will optionally read Code 128 add-ons with the UPC/EAN
label.
NOTE
Product Reference Guide
Contact Customer Support for
advanced programming of
optional and conditional addons.
93
Symbologies
Add-ons — continued
START / END
PROGRAMMING BARCODES
Disable Optional 2-Digit Add-ons
DEFAULT
Enable Optional 2-Digit Add-ons
Disable Optional 5-Digit Add-ons
DEFAULT
Enable Optional 5-Digit Add-ons
³
0
1 1 0 1
Disable Optional Code 128 Add-ons
DEFAULT
Enable Optional Code 128 Add-ons
94
MagellanTM 1100i
Add-ons
Add-ons — continued
2-Digit Addons Minimum Reads
This setting configures the minimum number of times a 2-digit addon must decode before it is
marked valid.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
Minimum = 2 Reads
DEFAULT
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
95
Symbologies
Add-ons — continued
5-Digit Addons Minimum Reads
This setting configures the minimum number of times a 5-digit addon must decode before it is
marked valid.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
96
MagellanTM 1100i
GS1 DataBar Omnidirectional / Stacked Omnidirectional
GS1 DataBar Omnidirectional / Stacked Omnidirectional
The following options apply to the GS1 DataBar Omnidirectional symbology.
Disable/Enable GS1 DataBar Omnidirectional
When this feature is disabled, the scanner will not read GS1 DataBar Omnidirectional barcodes.
START / END
PROGRAMMING BARCODES
Disable GS1 DataBar Omnidirectional
DEFAULT
Enable GS1 DataBar Omnidirectional
UCC/EAN 128 Emulation
When enabled, GS1 DataBar Omnidirectional barcodes will be translated to the UCC/EAN
128 label data format.
START / END
PROGRAMMING BARCODES
Disable UCC/EAN 128 Emulation
DEFAULT
Enable UCC/EAN 128 Emulation
Product Reference Guide
97
Symbologies
GS1 DataBar Omnidirectional / Stacked Omnidirectional — continued
Minimum Reads
This feature specifies the minimum number of consecutive times an GS1 DataBar Omnidirectional label must be decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
98
MagellanTM 1100i
GS1 DataBar Expanded / Expanded Stacked
GS1 DataBar Expanded / Expanded Stacked
The following options apply to the GS1 DataBar Expanded symbology.
Disable/Enable GS1 DataBar Expanded
When this feature is disabled, the scanner will not read GS1 DataBar Expanded barcodes.
START / END
PROGRAMMING BARCODES
Disable GS1 DataBar Expanded
DEFAULT
Enable GS1 DataBar Expanded
GS1-128 Emulation
When enabled, GS1 DataBar Expanded barcodes will be translated to the GS1-128 label data
format.
START / END
PROGRAMMING BARCODES
Disable GS1-128 Emulation
DEFAULT
Enable GS1-128 Emulation
Product Reference Guide
99
Symbologies
GS1 DataBar Expanded / Expanded Stacked — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START/END barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first fixed length by following the GS1 DataBar Expanded Length 1,
Length 2 Programming Instructions below.
5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the GS1 DataBar Expanded Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START/END barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first variable length by following the GS1 DataBar Expanded Length 1,
Length 2 Programming Instructions below.
5. Set Length 2 to the second variable length by following the GS1 DataBar Expanded Length
1, Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
100
MagellanTM 1100i
GS1 DataBar Expanded / Expanded Stacked
GS1 DataBar Expanded / Expanded Stacked — continued
GS1 DataBar Expanded Length 1, Length 2 Programming Instructions
1. Scan the START/END barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing
the length in decimal notation.
For GS1 DataBar Expanded barcodes,
only the data characters are included in
the length calculations.
NOTE
4. Scan the START/END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 01
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 74
Product Reference Guide
101
Symbologies
GS1 DataBar Expanded / Expanded Stacked — continued
Minimum Reads
This feature specifies the minimum number of consecutive times an GS1 DataBar Expanded
label must be decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
102
MagellanTM 1100i
GS1 DataBar Expanded / Expanded Stacked
GS1 DataBar Expanded / Expanded Stacked — continued
Coupon Read Control
This feature controls coupon reading.
START / END
PROGRAMMING BARCODES
Disable coupon filtering
Enable UPCA coupon decoding
Disable GS1 DataBar coupon decoding
DEFAULT
Enable GS1 DataBar coupon decoding
Disable UPCA coupon decoding
Product Reference Guide
103
Symbologies
GS1 DataBar Limited
The following options apply to the GS1 DataBar Limited symbology.
Disable/Enable GS1 DataBar Limited
When this feature is disabled, the scanner will not read GS1 DataBar Limited barcodes.
START / END
PROGRAMMING BARCODES
Disable GS1 DataBar Limited
DEFAULT
Enable GS1 DataBar Limited
GS1-128 Emulation
When enabled, GS1 DataBar Limited barcodes will be translated to the GS1-128 label data format.
START / END
PROGRAMMING BARCODES
Disable GS1-128 Emulation
DEFAULT
Enable GS1-128 Emulation
104
MagellanTM 1100i
GS1 DataBar Limited
GS1 DataBar Limited — continued
Minimum Reads
This feature specifies the minimum number of consecutive times an GS1 DataBar Limited label
must be decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
105
Symbologies
Code 39
The following options apply to the Code 39 symbology.
Disable/Enable Code 39
When this feature is disabled, the scanner will not read Code 39 barcodes.
START / END
PROGRAMMING BARCODES
Disable Code 39
Enable Code 39
DEFAULT
Check Character Calculation
When enabled, the scanner will calculate the check character of the labels. Turn this option on
only when a checksum is present in the Code 39 labels.
START / END
PROGRAMMING BARCODES
Disable Check Char Calculation
DEFAULT
Enable Check Char Calculation
106
MagellanTM 1100i
Code 39
Check Character Transmit
Enable this option to transmit the check character with scanned barcode data.
START / END
PROGRAMMING BARCODES
Disable Check Char Transmission
Enable Check Char Transmission
DEFAULT
Start/Stop Characters
Enables/disables transmission of Code39 start and stop characters.
START / END
PROGRAMMING BARCODES
Don’t Transmit Start/Stop Characters
DEFAULT
Transmit Start/Stop Characters
Product Reference Guide
107
Symbologies
Code 39 Full ASCII
Enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters.
START / END
PROGRAMMING BARCODES
Disable Code 39 Full ASCII
DEFAULT
Enable Code 39 Full ASCII
108
MagellanTM 1100i
Code 39
Code 39 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START/END barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first fixed length by following the Code 39 Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the Code 39 Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START/END barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first variable length by following the Code 39 Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second variable length by following the Code 39 Length 1, Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide
109
Symbologies
Code 39 Length 1, Length 2 Programming Instructions
1. Scan the START/END barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing
the length in decimal notation.
NOTE
For Code 39 barcodes, all check, data and full
ASCII shift characters are included in the
length calculations. Start/Stop characters are
not included.
4. Scan the START/END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 02
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
Quiet Zones
This feature enables/disables the requirement that quiet zones must be present for Code 39 barcodes.
START / END
PROGRAMMING BARCODES
Don’t require Quiet Zones
DEFAULT
Require Quiet Zones
110
MagellanTM 1100i
Code 39
Code 39 — continued
Code 39 Stitching
Enables/disables stitching for Code 39 labels. When parts of a Code 39 barcode are presented to
the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met.
START / END
PROGRAMMING BARCODES
Disable Code 39 Stitching
Enable Code 39 Stitching
DEFAULT
Minimum Reads
This feature specifies the minimum number of consecutive times a Code 39 label must be
decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
111
Symbologies
Code 32 Italian Pharmacode
The following options apply to the Code 32 Italian Pharmacode symbology.
Disable/Enable Code 32 Italian Pharmacode
When this feature is disabled, the scanner will not read Code 32 Italian Pharmacode barcodes.
START / END
PROGRAMMING BARCODES
Disable Code 32 Italian Pharmacode
DEFAULT
Enable Code 32 Italian Pharmacode
Start/Stop Characters
Enables or disables transmission of Code 32 Italian Pharmacode start/stop characters.
START / END
PROGRAMMING BARCODES
Don’t Transmit Start/Stop Characters
DEFAULT
Transmit Start/Stop Characters
³
112
0
0
6
0
1
MagellanTM 1100i
Code 32 Italian Pharmacode
Code 32 Italian Pharmacode — continued
Check Character Transmit
Enable this option to transmit the check character with scanned barcode data.
START / END
PROGRAMMING BARCODES
Disable Check Char Transmission
Enable Check Char Transmission
DEFAULT
Product Reference Guide
113
Symbologies
Code 128
The following options apply to the Code 128 symbology.
Disable/Enable Code 128
When this feature is disabled, the scanner will not read Code 128 barcodes.
START / END
PROGRAMMING BARCODES
Disable Code 128
Enable Code 128
DEFAULT
Disable/Enable EAN 128
When this feature is disabled, the scanner will not read EAN 128 barcodes.
START / END
PROGRAMMING BARCODES
Disable EAN 128
Enable EAN 128
DEFAULT
114
MagellanTM 1100i
Code 128
Code 128 — continued
Transmit Function Characters
Enables/disables transmission of Code128 function characters 1, 2, 3, and 4.
Function codes are transmitted as follows:
•
FNC1 = 80 hex
•
FNC2 = 81 hex
•
FNC3 = 82 hex
•
FNC4 = 83 hex
START / END
PROGRAMMING BARCODES
Don’t Transmit Function Characters
DEFAULT
Transmit Function Characters
Product Reference Guide
115
Symbologies
Code 128 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Code 128 Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the Code 128 Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first variable length by following the Code 128 Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second variable length by following the Code 128 Length 1, Length 2
Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
116
MagellanTM 1100i
Code 128
Code 128 — continued
Code 128 Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing
the length in decimal notation.
For Code 128 barcodes, only the data
characters are included in the length
calculations.
NOTE
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 01
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 80
Code 128 Conversion to Code 39
Enables/disables expansion of Code 128 labels to Code 39.
START / END
PROGRAMMING BARCODES
Disable
DEFAULT
Enable
Product Reference Guide
117
Symbologies
Code 128 — continued
Code 128 Stitching
Enables/disables stitching for Code 128 labels. When parts of a Code 128 barcode are presented
to the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s
software, and the data will be decoded if all barcode proofing requirements are met.
START / END
PROGRAMMING BARCODES
Disable Code 128 Stitching
Enable Code 128 Stitching
DEFAULT
Minimum Reads
This feature specifies the minimum number of consecutive times a Code 128 label must be
decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
118
MagellanTM 1100i
Interleaved 2 of 5
Interleaved 2 of 5
The following options apply to the Interleaved 2 of 5 (I 2 of 5) symbology.
Disable/Enable Interleaved 2 of 5
When this feature is disabled, the scanner will not read Interleaved 2 of 5 barcodes.
START / END
PROGRAMMING BARCODES
Disable Interleaved 2 of 5
DEFAULT
Enable Interleaved 2 of 5
Check Digit Calculation
When enabled, the scanner will calculate the check digit of the labels.
START / END
PROGRAMMING BARCODES
Disable Check Digit Calculation
DEFAULT
Enable Check Digit Calculation
Product Reference Guide
119
Symbologies
Interleaved 2 of 5 — continued
Check Digit Transmit
Enable this option to transmit the check digit with scanned barcode data.
START / END
PROGRAMMING BARCODES
Disable Check Digit Transmission
DEFAULT
Enable Check Digit Transmission
120
MagellanTM 1100i
Interleaved 2 of 5
Interleaved 2 of 5 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Interleaved 2 of 5 Length 1, Length 2
Programming Instructions below.
5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the Interleaved 2 of 5 Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first variable length by following the Interleaved 2 of 5 Length 1, Length
2 Programming Instructions below.
5. Set Length 2 to the second variable length by following the Interleaved 2 of 5 Length 1,
Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide
121
Symbologies
Interleaved 2 of 5 — continued
Interleaved 2 of 5 Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing
the length in decimal notation.
NOTE
For Interleaved 2 of 5 barcodes,
lengths must be an even number. Additionally, all check and data characters
are included in the length calculations.
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 06
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
122
MagellanTM 1100i
Interleaved 2 of 5
Interleaved 2 of 5 — continued
Interleaved 2 of 5 Stitching
Enables/disables stitching for Interleaved 2 of 5 labels. When parts of an Interleaved 2 of 5 barcode are presented to the scanner with this feature enabled, the barcode parts will be assembled
by the scanner’s software, and the data will be decoded if all barcode proofing requirements are
met.
Only functions when Fixed Length Decoding is
enabled.
NOTE
START / END
PROGRAMMING BARCODES
Disable Interleaved 2 of 5 Stitching
DEFAULT
Enable Interleaved 2 of 5 Stitching
Product Reference Guide
123
Symbologies
Interleaved 2 of 5 — continued
Minimum Reads
This feature specifies the minimum number of consecutive times an Interleaved 2 of 5 label
must be decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
124
MagellanTM 1100i
Codabar
Codabar
The following options apply to the Codabar symbology.
Disable/Enable Codabar
When this feature is disabled, the scanner will not read Codabar barcodes.
START / END
PROGRAMMING BARCODES
Disable Codabar
DEFAULT
Enable Codabar
Check Character Verification
When enabled, the scanner will verify the check character of the labels.
START / END
PROGRAMMING BARCODES
Disable Check Char Verification
DEFAULT
Enable Check Char Verification
Product Reference Guide
125
Symbologies
Check Character Transmit
Enable this option to transmit the check character with scanned barcode data.
START / END
PROGRAMMING BARCODES
Disable Check Char Transmission
Enable Check Char Transmission
DEFAULT
126
MagellanTM 1100i
Codabar
Codabar — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Codabar Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the Codabar Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first variable length by following the Codabar Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second variable length by following the Codabar Length 1, Length 2
Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide
127
Symbologies
Codabar — continued
Codabar Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing
the length in decimal notation.
For Codabar barcodes, all start, stop,
check and data characters are included
in the length calculations.
NOTE
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 03
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
Quiet Zones
This feature enable/disables the requirement that quiet zones must be present for Codabar barcodes.
START / END
PROGRAMMING BARCODES
Don’t require Quiet Zones
DEFAULT
Require Quiet Zones
128
MagellanTM 1100i
Codabar
Codabar — continued
Start/Stop Character Type
Codabar has four pairs of Start/Stop patterns. Select one pair to match your application.
START / END
PROGRAMMING BARCODES
Start/Stop Type: ABCD/TN*E
Start/Stop Type: ABCD/ABCD
Start/Stop Type: abcd/tn*e
Start/Stop Type: abcd/abcd
DEFAULT
Start/Stop Character Transmission
The transmission of start and end characters of Codabar is selected below.
START / END
PROGRAMMING BARCODES
Disable Start/Stop Char Transmission
Enable Start/Stop Char Transmission
DEFAULT
Product Reference Guide
129
Symbologies
Start/Stop Character Match
This feature enables/disables the requirement that start and stop characters match.
START / END
PROGRAMMING BARCODES
Disable Start/Stop Char Match
DEFAULT
Enable Start/Stop Char Match
Codabar Stitching
Enables/disables stitching for Codabar labels. When parts of a Codabar label are presented to
the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met.
Only functions when Fixed Length Decoding is
enabled.
NOTE
START / END
PROGRAMMING BARCODES
Disable Codabar Stitching
DEFAULT
Enable Codabar Stitching
130
MagellanTM 1100i
Codabar
Codabar — continued
Minimum Reads
This feature specifies the minimum number of consecutive times a Codabar label must be
decoded before it is accepted as a good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
131
Symbologies
Code 93
The following options apply to the Code 93 symbology.
Disable/Enable Code 93
When this feature is disabled, the scanner will not read Code 93 barcodes.
START / END
PROGRAMMING BARCODES
Disable Code 93
DEFAULT
Enable Code 93
132
MagellanTM 1100i
Code 93
Code 93 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START/END barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first fixed length by following the Code 93 Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the Code 93 Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START/END barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first variable length by following the Code 93 Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second variable length by following the Code 93 Length 1, Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide
133
Symbologies
Code 93 — continued
Code 93 Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing
the length in decimal notation.
For Code 93 barcodes, only the data
characters are included in the length
calculations.
NOTE
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 01
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
134
MagellanTM 1100i
Code 93
Code 93 — continued
Code 93 Stitching
Enables/disables stitching for Code 93 barcodes. When parts of a Code 93 label are presented to
the scanner with this feature enabled, the barcode parts will be assembled by the scanner’s software, and the data will be decoded if all barcode proofing requirements are met.
START / END
PROGRAMMING BARCODES
Disable Code 93 Stitching
DEFAULT
Enable Code 93 Stitching
Minimum Reads
This feature specifies the minimum number of consecutive times a Code 93 label must be
decoded before it is accepted as a good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
135
Symbologies
MSI/Plessey
The following options apply to the MSI/Plessey symbology.
Disable/Enable MSI/Plessey
When this feature is disabled, the scanner will not read MSI/Plessey barcodes.
START / END
PROGRAMMING BARCODES
Disable MSI/Plessey
DEFAULT
Enable MSI/Plessey
Check Digit Verification
This feature specifies whether one or two check digits are to be calculated and verified.
START / END
PROGRAMMING BARCODES
Disable Check Digit Verification
DEFAULT
Enable Check Digit Verification
136
MagellanTM 1100i
MSI/Plessey
MSI/Plessey — continued
Check Digit Transmit
When this option is enabled, the scanner will transmit one-digit or two-digit check digits,
depending upon the setting for check digit verification.
START / END
PROGRAMMING BARCODES
Disable Check Digit Transmission
Enable Check Digit Transmission
DEFAULT
Number of Check Characters
Specifies number of MSI/Plessey check characters to be calculated and verified
START / END
PROGRAMMING BARCODES
1 Check Character
DEFAULT
2 Check Characters
Product Reference Guide
137
Symbologies
MSI/Plessey — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START/END barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first fixed length by following the MSI/Plessey Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the MSI/Plessey Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START/END barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first variable length by following the MSI/Plessey Length 1, Length 2
Programming Instructions below.
5. Set Length 2 to the second variable length by following the MSI/Plessey Length 1, Length 2
Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
138
MagellanTM 1100i
MSI/Plessey
MSI/Plessey — continued
MSI/Plessey Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing
the length in decimal notation.
NOTE
For MSI/Plessey barcodes, all check and
data characters are included in the length
calculations.
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 04
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 16
Product Reference Guide
139
Symbologies
MSI/Plessey — continued
MSI/Plessey Stitching
Enables/disables stitching for MSI/Plessey barcodes. When parts of an MSI/Plessey label are
presented to the scanner with this feature enabled, the barcode parts will be assembled by the
scanner’s software, and the data will be decoded if all barcode proofing requirements are met.
Only functions when Fixed Length Decoding is
enabled.
NOTE
START / END
PROGRAMMING BARCODES
Disable MSI/Plessey Stitching
DEFAULT
Enable MSI/Plessey Stitching
140
MagellanTM 1100i
MSI/Plessey
MSI/Plessey — continued
Minimum Reads
This feature specifies the minimum number of consecutive times an MSI/Plessey label must be
decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
141
Symbologies
Standard 2 of 5
The following options apply to the Standard 2 of 5 symbology.
Disable/Enable Standard 2 of 5
When this feature is disabled, the scanner will not read Standard 2 of 5 barcodes.
START / END
PROGRAMMING BARCODES
Disable Std 2 of 5
DEFAULT
Enable Std 2 of 5
Check Digit Verification
When enabled, the scanner will verify the check digit of the labels.
START / END
PROGRAMMING BARCODES
Disable Check Digit Verification
DEFAULT
Enable Check Digit Verification
142
MagellanTM 1100i
Standard 2 of 5
Standard 2 of 5 — continued
Check Digit Transmit
When this option is enabled, the scanner will transmit the check digit.
START / END
PROGRAMMING BARCODES
Disable Check Digit Transmission
Enable Check Digit Transmission
DEFAULT
Product Reference Guide
143
Symbologies
Standard 2 of 5 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START/END barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first fixed length by following the Standard 2 of 5 Length 1, Length 2
Programming Instructions below.
5. Set Length 2 to the second fixed length (or to ‘00’ if there is only one fixed length) by following the Standard 2 of 5 Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START/END barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the START/END barcode.
4. Set Length 1 to the first variable length by following the Standard 2 of 5 Length 1, Length 2
Programming Instructions below.
5. Set Length 2 to the second variable length by following the Standard 2 of 5 Length 1, Length
2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
144
MagellanTM 1100i
Standard 2 of 5
Standard 2 of 5 — continued
Standard 2 of 5 Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Appendix C, Alpha-Numeric Pad and scan the two digits (zero padded) representing
the length in decimal notation.
For Standard 2 of 5 barcodes, all check
and data characters are included in the
length calculations.
NOTE
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 08
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 50
Product Reference Guide
145
Symbologies
Standard 2 of 5 — continued
Standard 2 of 5 Stitching
Enables/disables stitching for Standard 2 of 5 barcodes. When parts of a Standard 2 of 5 label
are presented to the scanner with this feature enabled, the barcode parts will be assembled by the
scanner’s software, and the data will be decoded if all barcode proofing requirements are met.
Only functions when Fixed Length Decoding is
enabled.
NOTE
START / END
PROGRAMMING BARCODES
Disable Std 2 of 5 Stitching
DEFAULT
Enable Std 2 of 5 Stitching
146
MagellanTM 1100i
Standard 2 of 5
Standard 2 of 5 — continued
Minimum Reads
This feature specifies the minimum number of consecutive times a Standard 2 of 5 label must be
decoded before it is accepted as good read.
START / END
PROGRAMMING BARCODES
Minimum = 1 Read
DEFAULT
Minimum = 2 Reads
Minimum = 3 Reads
Minimum = 4 Reads
Product Reference Guide
147
Symbologies
NOTES
148
MagellanTM 1100i
2D Symbologies
The features in this section are available ONLY for models with
2D features activated.
NOTE
2D Symbologies
The scanner supports the 2D symbologies (barcode types) listed below. Available options for
each 2D symbology are included in this chapter.
• PDF 417
• Maxicode
• Micro PDF 417
• Aztec
• Datamatrix
• Composite Labels
• QR Code
Factory Defaults— for the standard RS-232 interface are indicated in bold text throughout.
2D Decode Time Max
This feature sets the maximum amount of time the software will spend attempting to decode a
2D label. Follow these instructions to configure this feature:
1. Scan the START barcode.
2. Scan the Set 2D Decode Time Max barcode.
3. Turn to Alpha-Numeric Pad and scan the two digits (zero-padded) representing the desired
contrast in decimal notation. The configurable range is 01-0xFF by 01 in increments of
10 msec.
4. Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set 2D Decode Time Max
DEFAULT SETTING FOR THIS FEATURE: 350 msec
Product Reference Guide
149
2D Symbologies
PDF 417
Disable/Enable PDF 417
When disabled, the scanner will not read PDF 417 barcodes.
START / END
PROGRAMMING BARCODES
Disable PDF 417
Enable PDF 417
DEFAULT
150
MagellanTM 1100i
2D Symbologies
PDF 417 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by
following the PDF 417 Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the minimum length by following the PDF 417 Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the maximum length by following the PDF 417 Length 1, Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide
151
2D Symbologies
PDF 417 — continued
PDF 417 Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
For PDF 417 barcodes, only the data characters are
included in the length calculations.
NOTE
Any value set higher than 2710 will be considered to be
2710.
Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 2710
152
MagellanTM 1100i
2D Symbologies
Micro PDF 417
Disable/Enable Micro PDF 417
When disabled, the scanner will not read Micro PDF 417 barcodes.
START / END
PROGRAMMING BARCODES
Disable Micro PDF 417
DEFAULT
Enable Micro PDF 417
Product Reference Guide
153
2D Symbologies
Micro PDF 417 — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by
following the Micro PDF 417 Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the minimum length by following the Micro PDF 417 Length 1, Length 2
Programming Instructions below.
5. Set Length 2 to the maximum length by following the Micro PDF 417 Length 1, Length 2
Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
154
MagellanTM 1100i
2D Symbologies
Micro PDF 417 — continued
Micro PDF 417 Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
For Micro PDF 417 barcodes, only the data characters are
included in the length calculations.
NOTE
Any value set higher than 366 will be considered to be 366.
Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING0350
FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 0366
Product Reference Guide
155
2D Symbologies
Datamatrix
Disable/Enable Datamatrix
When disabled, the scanner will not read Datamatrix barcodes.
START / END
PROGRAMMING BARCODES
Disable Datamatrix
Enable Datamatrix
DEFAULT
156
MagellanTM 1100i
2D Symbologies
Datamatrix — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by
following the Datamatrix Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the minimum length by following the Datamatrix Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the maximum length by following the Datamatrix Length 1, Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide
157
2D Symbologies
Datamatrix — continued
Datamatrix Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
For Datamatrix barcodes, only the data characters are
included in the length calculations.
NOTE
Any value set higher than 800 will be considered to be 800.
Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 0800
158
MagellanTM 1100i
2D Symbologies
QR Code
Disable/Enable QR Code
When disabled, the scanner will not read QR Code labels.
START / END
PROGRAMMING BARCODES
Disable QR Code
DEFAULT
Enable QR Code
Product Reference Guide
159
2D Symbologies
QR Code — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by
following the QR Code Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the minimum length by following the QR Code Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the maximum length by following the QR Code Length 1, Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
160
MagellanTM 1100i
2D Symbologies
QR Code — continued
QR Code Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
For QR Code labels, only the data characters are included
in the length calculations.
NOTE
Any value set higher than 2710 will be considered to be
2710.
Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 2710
Product Reference Guide
161
2D Symbologies
Maxicode
Disable/Enable Maxicode
When disabled, the scanner will not read Maxicode labels.
START / END
PROGRAMMING BARCODES
Disable Maxicode
DEFAULT
Enable Maxicode
162
MagellanTM 1100i
2D Symbologies
Maxicode — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by
following the Maxicode Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the minimum length by following the Maxicode Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the maximum length by following the Maxicode Length 1, Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
Product Reference Guide
163
2D Symbologies
Maxicode — continued
Maxicode Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
For Maxicode labels, only the data characters are included
in the length calculations.
NOTE
Any value set higher than 138 will be considered to be 138.
Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 0138
164
MagellanTM 1100i
2D Symbologies
Aztec
Disable/Enable Aztec
When disabled, the scanner will not read Aztec labels.
START / END
PROGRAMMING BARCODES
Disable Aztec
DEFAULT
Enable Aztec
Product Reference Guide
165
2D Symbologies
Aztec — continued
Length Control
Fixed Length Decoding— When fixed length decoding is enabled, the scanner will decode a
barcode if the label length matches one of the configurable fixed lengths.
Variable Length Decoding— When variable length decoding is enabled, the scanner will
decode a barcode if the label length falls in the range of the configurable minimum and maximum length.
Configuring Fixed Length Decoding:
1. Scan the START barcode.
2. Scan the Fixed Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the first fixed length by following the Length 1, Length 2 Programming
Instructions below.
5. Set Length 2 to the second fixed length (or to ‘0000’ if there is only one fixed length) by
following the Aztec Length 1, Length 2 Programming Instructions below.
Configuring Variable Length Decoding:
1. Scan the START barcode.
2. Scan the Variable Length Decoding barcode.
3. Scan the END barcode.
4. Set Length 1 to the minimum length by following the Aztec Length 1, Length 2 Programming Instructions below.
5. Set Length 2 to the maximum length by following the Aztec Length 1, Length 2 Programming Instructions below.
START / END
PROGRAMMING BARCODES
Variable Length Decoding
DEFAULT
Fixed Length Decoding
166
MagellanTM 1100i
2D Symbologies
Aztec — continued
Aztec Length 1, Length 2 Programming Instructions
1. Scan the START barcode.
2. Scan either the Set Length 1 or Set Length 2 barcode.
3. Turn to Alpha-Numeric Pad and scan the four digits (zero-padded) representing the length.
For Aztec labels, only the data characters are included in
the length calculations.
NOTE
Any value set higher than 3700 will be considered to be
2710.
Scan the END barcode.
START / END
PROGRAMMING BARCODES
Set Length 1
DEFAULT SETTING FOR THIS FEATURE: 0001
Set Length 2
DEFAULT SETTING FOR THIS FEATURE: 2710
Product Reference Guide
167
2D Symbologies
Composite Labels
Disable/Enable GS1 DataBar Omnidirectional 2D Component
When enabled, if a GS1 DataBar Omnidirectional label is decoded which has the 2D linkage
flag set, the 2D component must also be decoded or the base label will be discarded.
When disabled, only the GS1 DataBar Omnidirectional base label will be decoded and transmitted regardless of the state of the linkage flag.
START / END
PROGRAMMING BARCODES
Disable GS1 DataBar Omnidirectional 2D Component
DEFAULT
Enable GS1 DataBar Omnidirectional 2D Component
Disable/Enable GS1 DataBar Expanded 2D Component
When enabled, if a GS1 DataBar Expanded label is decoded which has the 2D linkage flag set,
the 2D component must also be decoded or the base label will be discarded.
When disabled, only the GS1 DataBar Expanded base label will be decoded and transmitted
regardless of the state of the linkage flag.
START / END
PROGRAMMING BARCODES
Disable GS1 DataBar Expanded 2D Component
DEFAULT
Enable GS1 DataBar Expanded 2D Component
168
MagellanTM 1100i
2D Symbologies
Disable/Enable GS1 DataBar Limited 2D Component
When enabled, if a GS1 DataBar Limited label is decoded which has the 2D linkage flag set, the
2D component must also be decoded or the base label will be discarded.
When disabled, only the GS1 DataBar Limited base label will be decoded and transmitted
regardless of the state of the linkage flag.
START / END
PROGRAMMING BARCODES
Disable GS1 DataBar Limited 2D Component
DEFAULT
Enable GS1 DataBar Limited 2D Component
Product Reference Guide
169
2D Symbologies
NOTES
170
MagellanTM 1100i
Advanced Decoding Features
Pharmacy Patterns
Enables/disables using the pharmacy patterns.
START / END
PROGRAMMING BARCODES
Pharmacy Patterns = Disable
DEFAULT
Pharmacy Patterns = Enable
Product Reference Guide
171
Advanced Decoding Features
Inverse Label Reading
This controls the method of reading inverse labels (white label on black background).
This feature is only available for GS1 DataBar and 2D symbologies.
NOTE
START / END
PROGRAMMING BARCODES
2D Read Mode = Reads only normal labels
DEFAULT
2D Read Mode = Reads both normal and inverse
labels
2D Read Mode = Reads only inverse labels
172
MagellanTM 1100i
Chapter A
Product Specifications
Optical and Read Performance Parameters
Parameter
Specification
Scan Volume
70 cubic inches
Scan Pattern
136 Scan Lines
Scan Rate
1,768 scan lines/second
Minimum Resolution
5 mil
0 - 7”
Depth of Field
(100% UPC Labels)
Minimum Print Contrast
Ratio
25%
Skew (Yaw)
± 75
Pitch
± 65
Roll
Between 0 and 360
Scanner Dimensions
139.58mm
5.5"
75.44mm
2.97"
97.84mm
3.85"
83.25mm
3.28"
25.4mm
1.0"
Product Reference Guide
173
Physical Properties
Parameter
Specification
Dimensions (Scanner
only):
3.3” x2.8” x3.7”
Dimensions (Scanner w/
Base Station):
5.5” x2.9” x3.8”
Weight (Scanner)
7.0 oz.
Weight (Base Station)
6.6 oz.
Electrical Parameters
Parameter
Operating Voltage
Input Current
Operating (idle)
Operating (label read)
Specification
Input voltage 4.5 to 14 VDC
<300mA
<400 mA
Environmental Parameters
Parameter
Specification
Mechanical Shock
Multi 1.2m drops
Contaminants
Water and Dust
IP52
Temperature Ranges:
Operating
Storage
Ambient Light Indoor
Ambient Light Outdoor
Humidity
Beeper/Speaker
Vibration
32 F to +104 F (0 C to +40 C)
-40 F to +158 F (-40 C to + 70C)
0 - 6000 lux
0 - 86,100 lux
5 to 95% non-condensing
70-85dBA at a distance of 3’-3” (1
meter)
Retail/Office
Other Parameters
Parameter
EAS Support
174
Specification
YES (Checkpoint)
MagellanTM 1100i
Chapter B
Cable Pinouts
Standard Cable Pinouts (Primary Interface Cables)
RS-232
1
2 CTS
3
4 RTS
5 RXD
6 TXD
7
8 VCC IN
9 GND
10
10 Position RJ
Pin 1
(Scanner End)
IBM Port 5B/9B/17
1 
2 
3 
4 DATA -
5
6 DATA +
7
8 VCC_IN
9 GND
10
10 Position RJ
Pin 1
Product Reference Guide
(Scanner End)
175
Cable Pinouts
USB-OEM
1 
2 
3 
4 D -
5
6 D +
7
8 VIN
9 GND
10
10 Position RJ
Pin 1
(Scanner End)
USB, USB Keyboard & USB COM
1 
2 
3 
4 D -
5
6 D +
7
8 VBUS_VIN
9 GND
10
10 Position RJ
Pin 1
(Scanner End)
Keyboard Wedge
1
2 KB_DATA
3 AT_CLK
4 KB_CLK
5
6 AT_DATA
7
8 VCC_IN
9 GND
10
176
10 Position RJ
Pin 1
(Scanner End)
MagellanTM 1100i
Chapter C
Alpha-Numeric Pad
A
B
C
D
E
F
Product Reference Guide
177
Alpha-Numeric Pad
1
2
3
4
5
6
7
8
9
0
178
MagellanTM 1100i
Appendix D
Default Settings
Defaults by Symbology
The following is a partial list of key settings for each symbology type.
Read
Enable
Checksum
Verification
Enable
Checksum
Transmission
Enable
Label
ID
UPC-A



A
UPC-E



E
EAN-13



F
EAN-8



FF
Code Type
GS1 DataBar Omnidirectional
R4
GS1 Expanded
RX
Code 39


A
PharmaCode 39
Code 128
*
#

Interleaved 2 of 5

i
Codabar

%
&
Code 93
MSI/Plessey

@
Standard 2 of 5

s
PDF 417
P
Micro PDF 417
mP
Datamatrix
Dm
QR Code
QR
Maxicode
MC
Aztec
Az
GS1 DataBar Omnidirectional 2D Composite
R4
GS1 DataBar Expanded 2D Composite
RX
GS1 DataBar Limited 2D Composite
RL
Product Reference Guide
179
Interface Default Exceptions
The factory default settings indicated in the programming sections (in bold text) reflect factory configuration
for the RS-232 standard interface. The following tables list default exceptions by interface for the remaining
available interfaces.
IBM Interfaces
IBM Interfaces include USB-OEM, IBM Port 9B, IBM Port5B and IBM Port17.
Parameter
180
Default Setting
IBM Interface Type
IBM Port 9B
Number of Host Transmit Buffers
One Buffer
Label I.D. Transmission
Disable
Suffix Characters
No Suffix
MagellanTM 1100i
Interface Default Exceptions
Interface Default Exceptions — continued
RS-232 Wincor/Nixdorf
Parameter
Default Setting
Interface Type
RS-232-WN
Number of Host Transmit Buffers
One Buffer
RS-232 Parity
Odd
RS-232 Hardware Control
CTS Flow Control
UPC-E Check Character Conversion
Disabled
UCC/EAN-128 Label ID
‘P’
Code 39 Label ID
‘M’
Code 93 Label ID
‘L’
Code 128 Label ID
‘K’
Codabar Label ID
‘N’
EAN-8 Label ID
‘B’
EAN-13 Label ID
‘A’
ISBN Label ID
‘A’
Interleaved 2 of 5 Label ID
‘I’
Standard 2 of 5 Label ID
‘H’
MSI/Plessey Label ID
‘O’
UPC-E Label ID
‘C’
GS1 DataBar Omnidirectional Label ID
‘E’
GS1 Expanded Label ID
‘E’
Product Reference Guide
181
Interface Default Exceptions — continued
Keyboards
Keyboard interfaces include USB Keyboard and Keyboard Wedge A-J.
Parameter
182
Default Setting
Keyboard Wedge Interface Type
USB Keyboard
Label ID Transmission
Disable
MagellanTM 1100i
Appendix E
Keyboard Function Key Mappings
Keyboard Model Cross Reference
Table E-1
summarizes the keyboard models, their defined protocol, scancode set, and some unique features. The
remaining tables in this chapter provide the function key maps associated with each of the scancode sets.
Table E-1. Keyboard Model Cross Reference
Model Type
PC/XT Foreign ALT Mode
AT; 
PS/2 25-286; 
PS/2 30-286; 
PS/2 50, 50Z; 
PS/2 60,70,80,90,95
Foreign ALT Mode
PS/2 25 and 30 
Foreign ALT Mode
PC/XT U.S. Mode
AT; 
PS/2 25-286; 
PS/2 30-286; 
PS/2 50, 50Z; 
PS/2 60,70,80,90,95
U.S. Mode + specific
country support
PS/2 25 and 30
U.S. Mode
IBM 3xxx Terminals 
(122-key keyboard)
IBM 3xxx Terminals
(102-key keyboard)
PS55 5530T with
JAPANESE DOS (TDOS)
NEC 9801
Product Reference Guide
I/F ID
Func.
Use
Key
Country
Map
Mode
Support
Scan Set 1 No
No
TransScancode
mission
Set
Protocol
Wedge A
PC/XT
Wedge B
AT/PS2 Scan Set 2
No
No
Wedge C
AT/PS2 Scan Set 1
No
No
Wedge D
PC/XT
Scan Set 1
Yes
No
Wedge E
AT/PS2 Scan Set 2
Yes
Yes
Wedge F
AT/PS2 Scan Set 1
Yes
No
Wedge G
AT/PS2 Scan Set 3
Yes
No
Wedge H
AT/PS2 Scan Set 3
Yes
No
Wedge I
AT/PS2
Japanese
DOS
Yes
No
Wedge J
NEC
9801
NEC 9801
Yes
No
183
Table E-2. USB Function Key Usage Map
ASCII
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
184
Key value
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
Usage Name
ALT right Make
ALT right Break
F11
F12
GUI right Make
GUI right Break
CTRL right Make
CTRL right Break
BS
TAB right
RIGHT arrow (inner keypad)
TAB left
Enter (right keypad)
CR
INSERT (inner keypad)
PAGE UP (inner keypad)
PAGE DOWN (inner keypad)
HOME (inner keypad)
LEFT arrow (inner keypad)
DOWN arrow (inner keypad)
UP arrow (inner keypad)
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
Modifier/Scancode
40h 00h
00h 00h1
00h 44h
00h 45h
80h 00h
00h 00h1
10h 00h
00h 00h1
00h 2Ah
00h 2Bh
00h 4Fh
02h 2Bh
00h 58h
00h 28h
00h 49h
00h 4Bh
00h 4Eh
00h 4Ah
00h 50h
00h 51h
00h 52h
00h 3Fh
00h 3Ah
00h 3Bh
00h 3Ch
00h 3Dh
00h 3Eh
00h 29h
00h 40h
00h 41h
00h 42h
00h 43h
MagellanTM 1100i
Keyboard Model Cross Reference
Table E-3. Scanset 1 Function Key Map
ASCII
(hex)
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
ASCII code
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
Key
ALT right Make
ALT right Break
ALT left Make
ALT left Break
CTRL left Make
CTRL left Break
CTRL right Make
CTRL right Break
BS
TAB right
RIGHT arrow (inner keypad)
TAB left
Enter (inner keypad)
CR
INSERT (inner keypad)
PAGE UP (inner keypad)
PAGE DOWN (inner keypad)
HOME (inner keypad)
LEFT arrow (inner keypad)
DOWN arrow (inner keypad)
UP arrow (inner keypad)
Scancode
E0h 38h
E0h B8h
38h
B8h
1Dh
9Dh
E0h 1Dh
E0h 9Dh
0Eh
0Fh
4Dh + E0
0Fh + S
1Ch + E0
1Ch
52h + E0
49h + E0
51h + E0
47h + E0
4Bh + E0
50h + E0
48h + E0
Table E-4. Scanset 2 Function Key Map
ASCII
(hex)
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
Product Reference Guide
ASCII code
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
Key
ALT right Make
ALT right Break
ALT left Make
ALT left Break
CTRL left Make
CTRL left Break
CTRL right Make
CTRL right Break
BS
TAB right
RIGHT arrow (inner keypad)
TAB left
Enter (right keypad)
CR
INSERT (inner keypad)
PAGE UP (inner keypad)
PAGE DOWN (inner keypad)
HOME (inner keypad)
LEFT arrow (inner keypad)
DOWN arrow (inner keypad)
UP arrow (inner keypad)
F6
F1
F2
F3
Scancode
E0h 11h
E0h F0h 11h
11h
F0h 11h
14h
F0h 14h
E0h 14h
E0h F0h 14h
66h
0Dh
74h + E0
0Dh + S
5Ah + E0
5Ah
70h + E0
7Dh + E0
7Ah + E0
6Ch + E0
6Bh + E0
72h + E0
75h + E0
0Bh
05h
06h
04h
185
19
1A
1B
1C
1D
1E
1F
EM
SUB
ESC
FS
GS
RS
US
F4
F5
ESC
F7
F8
F9
F10
0Ch
03h
76h
83h
0Ah
01h
09h
Table E-5. Scanset 3, 102-Key Function Key Map
ASCII (hex)
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
186
ASCII code
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
Key
ALT right Make
ALT right Break
ALT left Make
ALT left Break
CTRL left Make
CTRL left Break
CTRL right Make
CTRL right Break
BS
TAB right
RIGHT arrow (inner keypad)
TAB left
Enter (inner keypad)
CR
INSERT (inner keypad)
PAGE UP (inner keypad)
PAGE DOWN (inner keypad)
HOME (inner keypad)
LEFT arrow (inner keypad)
DOWN arrow (inner keypad)
UP arrow (inner keypad)
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
Scancode
39h
F0h 39h
19h
F0h 19h
11h
F0h 11h
58h
F0h 58h
66h
0Dh
6Ah
0Dh + S
79h
5Ah
67h
6Fh
6Dh
6Eh
61h
60h
63h
2Fh
07h
0Fh
17h
1Fh
27h
08h
37h
3Fh
47h
4Fh
MagellanTM 1100i
Keyboard Model Cross Reference
Table E-6. Scanset 3 122-Key Function Key Map
ASCII (hex) ASCII code
00
NUL
01
SOH
02
STX
03
ETX
04
EOT
05
ENQ
06
ACK
07
BEL
08
BS
09
HT
0A
LF
0B
VT
0C
FF
0D
CR
0E
SO
0F
SI
10
DLE
11
DC1
12
DC2
13
DC3
14
DC4
15
NAK
16
SYN
17
ETB
18
CAN
19
EM
1A
SUB
1B
ESC
1C
FS
1D
GS
1E
RS
1F
US
Product Reference Guide
Key
ALT Right Make
ALT Right Break
ALT left Make
ALT left Break
CTRL left (RESET) Make only
CTRL left (RESET) Make/Break
ONLINE Enter Make only
ONLINE Enter Make/Break
BS
TAB right
RIGHT arrow (inner keypad)
TAB left
CR (FIELD EXIT) Make only
CR (FIELD EXIT) Make/Break
INSERT (inner keypad)
FIELD +
FIELD HOME (inner keypad)
LEFT arrow (inner keypad)
DOWN arrow (inner keypad)
UP arrow (inner keypad)
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
Scancode
39h
F0h 39h
19h
F0h 19h
11h
11h F0h 11h
58h
58h F0h 58h
66h
0Dh
6Ah
0Dh + S
5Ah F0h 5Ah
5Ah
65h
79h
7Ch
62h
61h
60h
63h
2Fh
07h
0Fh
17h
1Fh
27h
08h
37h
3Fh
47h
4Fh
187
Table E-7. Japanese DOS Function Key Map
ASCII value
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
188
ASCII code
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
Key
ALT right Make
ALT right Break
ALT left Make
ALT left Break
CTRL left Make
CTRL left Break
CTRL right Make
CTRL right Break
BS
TAB right
RIGHT arrow (inner keypad)
TAB left
Enter (right keypad)
CR
INSERT (inner keypad)
PAGE UP (inner keypad)
PAGE DOWN (inner keypad)
HOME (inner keypad)
LEFT arrow (inner keypad)
DOWN arrow (inner keypad)
UP arrow (inner keypad)
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
Scancode
31h
B1h
31h
B1h
41h
C1h
41h
C1h
3Eh
3Ch
4Dh
3Ch + S
60h
3Bh
52h
49h
51h
4Ch
4Bh
4Ah
4Eh
6Dh
68h
69h
6Ah
6Bh
6Ch
3Dh
6Eh
6Fh
70h
71h
MagellanTM 1100i
Keyboard Model Cross Reference
Table E-8. NEC 9801-Key Function Key Map
ASCII value
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
13h
14h
15h
16h
17h
18h
19h
1Ah
1Bh
1Ch
1Dh
1Eh
1Fh
Product Reference Guide
ASCII code
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
Key
unused
CR
CAPS LOCK ON (make)
CAPS LOCK OFF (break)
CTRL left Make
CTRL left Break
CTRL-C
n/a
BS
TAB right
RIGHT arrow (inner keypad)
TAB left
DELETE
CR
INSERT (inner keypad)
KATAKANA LOCK ON (Make)
KATAKANA LOCK OFF (Break)
HOME (inner keypad)
LEFT arrow (inner keypad)
DOWN arrow (inner keypad)
UP arrow (inner keypad)
F6
F1
F2
F3
F4
F5
ESC
F7
F8
F9
F10
Scancode
n/a
1Ch
71h
F1h
74h
F4h
60h
n/a
0Eh
0Fh
3Ch
0Fh + S
39h
1Ch
38h
72h
F2h
3Eh
3Bh
3Dh
3Ah
67h
62h
63h
64h
65h
66h
00h
68h
69h
6Ah
6Bh
189
NOTES
190
MagellanTM 1100i
Chapter F
Host Commands
Accepting RS-232 Commands
The scanner responds to the following RS-232 commands:
COMMAND
ASCII
HEX
COMMENT
Enable Scanner
E
0x45
Disable
Scanner
D
0x44
Reset Scanner
R
0x52
Not On File
Indication
F
0x46
Long series of beeps
Beep Good
Read Tone
B
0x42
Beeps if Good Read Beep is enabled
Force Good
Read Tone
!
0x01
Beeps regardless of beep setting
Bel
‘
0x07
Force Good Read Tone
Identification
request
i
0x69
Returns long responsea
Health request
h
0x68
Returns long responsea
Status request
s
0x73
Returns long responsea
a. Call Tech Support for information.
If one of the above commands is received, the scanner will perform the steps indicated for the command. Host
commands for other interfaces are also available. Contact Tech Support for more details.
Product Reference Guide
191
NOTES
192
MagellanTM 1100i
Chapter G
Sample Symbols
1D Symbol Samples
UPC-A
0
5
0 1234567890
Interleaved 2 of 5
1234567890
Code 128
Code 128
EAN-13
9 780330 290951
Code 39
BC321
Codabar
A13579B
Code 93
123456-9$
Product Reference Guide
193
1D Symbol Samples — continued
Code 2 of 5
123456
GS1 DataBar Omnidirectional
(01)00123456789012
GS1 DataBar Expanded
0100123456789050
GS1 DataBar Limited
(01)16543210987654
194
MagellanTM 1100i
2D Sample Symbols
2D Sample Symbols
PDF 417
A12B3C
Micro PDF 417
BV17453
Datamatrix
1314H17LL
QR Code
35900G9
Maxicode
111TUVCCIUL7-1
Aztec
This is an Aztec Code
Product Reference Guide
195
Composite Sample Symbols
GS1 DataBar Limited Composite
GS1 DataBar Truncated Composite
196
MagellanTM 1100i
Composite Sample Symbols
NOTES
Product Reference Guide
197
NOTES
198
MagellanTM 1100i
ASCII Chart
ASCII
Char.
Hex
No.
ASCII
Char.
Hex
No.
ASCII
Char.
Hex
No.
ASCII
Char.
Hex
No.
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
SP
!
“
#
$
%
&
’
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
‘
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
DEL
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
www.datalogic.com
© 2005-2013 Datalogic ADC, Inc. • All rights reserved. • 
Datalogic and the Datalogic logo are registered trademarks of
Datalogic S.p.A. in many countries, including the U.S.A. and the E.U.
Datalogic ADC, Inc.
959 Terry Street | Eugene |OR 97402 | USA
Telephone: (1) 541-683-5700 | Fax: (1) 541-345-7140
820034314 (Rev.F)
November 2013