ViewSonic VT3205LED User guide

VT3205LED
LCD TV
- User Guide
- Guide de l’utilisateur
- Guida dell’utente
IMPORTANT: Please read this User Guide to obtain important information on
installing and using your product in a safe manner, as well as registering your
product for future service. Warranty information contained in this User Guide will
describe your limited coverage from ViewSonic Corporation, which is also found
on our web site at http://www.viewsonic.com in English, or in specific languages
using the Regional selection box in the upper right corner of our website.
“Antes de operar su equipo lea cuidadosamente las instrucciones en
este manual”
Model No. : VS13915-1M
Contents
Compliance Information............................................................................................i
Declaration of RoHS Compliance ..............................................................................ii
Copyright Information .................................................................................................iii
Product Registration ...................................................................................................iii
TV Wall Mount ..............................................................................................................iv
Safety Instructions ......................................................................................................iv
Wet Location ................................................................................................................iv
Outdoor Use .................................................................................................................iv
Disconnect Device - The Mains Plug or An Appliance Coupler ............................. iv
WARNING ..................................................................................................................... v
Getting Started
List of Features............................................................................................................ 1
Package Contents........................................................................................................1
Installing the LCD TV...................................................................................................2
Installing the Stand .................................................................................................... 2
Disconnecting the Stand ............................................................................................ 2
Mounting ViewSonic LCD TV to the wall ................................................................... 3
....................................................................... 4
Front View of the Product ...........................................................................................5
Rear View of the Product ............................................................................................6
Connecting the LCD TV...............................................................................................9
Cable System or VHF/UHF Antenna System ............................................................9
Cable System and VHF/UHF Antenna System .........................................................9
HD Cable Box/HD Satellite Box .................................................................................9
Personal Computer ....................................................................................................11
Other Equipment ...............................................................................................12
Using the TV Features
Remote Control and TV Controls .............................................................................13
Inserting Remote Control Batteries............................................................................13
Remote Control and TV Controls...............................................................................13
Operation...................................................................................................................... 16
Other Information
Cleaning the LCD TV ..................................................................................................33
Programming your Cable or Satellite Box remote ................................................... 33
Troubleshooting ..........................................................................................................34
Specifications ..............................................................................................................36
RS232 Protocol ............................................................................................................37
Customer Support .......................................................................................................48
Limited Warranty .........................................................................................................49
Mexico Limited Warranty ............................................................................................50
ViewSonic
VT3205LED
ENGLISH
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment
Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste,
but use the return and collection systems according to local law.
If the batteries, accumulators and button cells included with this equipment, display the chemical
symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than
0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.
ENERGY STAR Information:
To ensure your television is operating at optimal energy efficiency, select [Home] mode during initial
activation.
To return to [Home] mode settings, select [Standard] picture mode. [Standard] mode is recommended for
normal home use.
Keeping the TV at its factory default settings that meet ENERGY STAR criteria.
Enabling certain features and functionality of LED TV will increase its energy consumption, possibly beyond
the limits required for ENERGY STAR qualification.
SRS Trademark Information:
• is a trademark of SRS Labs, Inc. TruSurround HD technology is incorporated under license
from SRS Labs, Inc.
SRS TruSurround HD™ creates an immersive, feature-rich surround sound experience from two speakers,
complete with rich bass, high frequency detail and clear dialog.
ViewSonic
i
VT3205LED
This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European
Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic
equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the
European Technical Adaptation Committee (TAC) as shown below:
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb)
0.1%
< 0.1%
Mercury (Hg)
0.1%
< 0.1%
Cadmium (Cd)
0.01%
< 0.01%
Hexavalent Chromium (Cr6+)
0.1%
< 0.1%
Polybrominated biphenyls (PBB)
0.1%
< 0.1%
Polybrominated diphenyl ethers (PBDE)
0.1%
< 0.1%
Substance
Certain components of products as stated above are exempted under the Annex of the RoHS Directives as
noted below:
Examples of exempted components are:
1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not specifically
mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and electronic ceramic parts
(e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up to
0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.
ViewSonic
ii
VT3205LED
ENGLISH
Declaration of RoHS Compliance
ENGLISH
Copyright Information
Copyright © ViewSonic® Corporation, 2011. All rights reserved.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).
As an ENERGY STAR® partner, ViewSonic Corporation has determined that this product meets the ENERGY
STAR® guidelines for energy efficiency.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance
or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change
product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without
prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available, please
register your product on the Internet at: www.viewsonic.com.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
VT3205LED
ViewSonic LED TV
VS13915-1M
VT3205LED-1M_UG_ENG Rev. 1B 08-18-11
_________________________________
_________________________________
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green. Thank you for being part
of Smarter, Greener Computing. Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
ViewSonic
iii
VT3205LED
Caution
ENGLISH
Please use the following ViewSonic TVs only with the following wall-mount kit.
ViewSonic TV Model No.
VT3205LED
ViewSonic Wall-Mount
kit model
WMK-13
Use with other Wall-Mount kit may cause instability and possibly result in injury.
To find the perfect mount for VT3205LED, please browse www.viewsonic.com or call our
service team: United States 1-800-688-6688, Canada 1-866-463-4775.
Safety Instructions
The symbol is intended to alert the user to presence of un-insulated “Hazardous
Voltage” within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
This symbol is intended to alert the user that improper use of the product may
result in product malfunction. The user should pay attention to avoid accidents or
unnecessary problems.
Wet Location
Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Outdoor Use
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or
moisture.
Disconnect Device - The Mains Plug or An Appliance
Coupler
The mains plug or an appliance coupler is used as the disconnect device for disconnection from
the mains, the disconnect device shall remain readily operable.
ViewSonic
iv
VT3205LED
ENGLISH
WARNING
Do not expose this TV to rain or moisture.
It may increase the risk to fire or
electronic shock.
Dangerous Voltage:
The lightning flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user to
the presence of dangerous
voltage within the inside
of the product that may be
sufficient level to constitute
a risk of electric shock to
persons.
Instruction: The
exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and servicing
instructions in the literature
accompanying the appliance.
The TV shall not be exposed to dripping
or splashing. Do not put objects filled
with liquids, such as vases, on the TV.
CAUTION
To prevent electric shock, do not use
this polarized AC plug with an extension
cord, receptacle or other outlet unless the
blades can be fully inserted to prevent
blade exposure.
Declaration of Conformity
Trade Name: ViewSonic Model:
VT3205LED Responsible Party: ViewSonic
Corporation Address: 381 Brea Canyon Road,
Walnut, CA. 91789 USA Telephone Number:
1-800-688- 6688 This device complies with
part 15 of the FCC rules. Operation is subject
to the following two conditions: 1) This device
may not cause harmful interference, and 2) this
device must accept any interference received,
including interference that may cause undesired
operation.
NOTIFICATION
This device has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
ViewSonic
FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a residential
installation. This device generates,
uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
device and receiver.
• Connect the device into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Pursuant to FCC regulations, be
cautioned that any changes or
modifications not expressly approved
in this manual could void your
authority to operate this equipment.
Safety
• Operate the TV on 120V AC only.
• Use the AC power cord specified by
ViewSonic and suitable for the voltage
where you use it.
• The plug is designed, for safety
purposes, to fit into the wall outlet only
one way.
• If you are unable to insert the plug
fully into the outlet, contact your
dealer.
• If any liquid or solid object should
fall inside the cabinet, stop operating,
unplug the TV immediately and
have it checked by qualified service
technician.
• If you will not be using the TV for a
long time, disconnect the power by
pulling the plug itself. Do not pull on
the cord.
• For details concerning safety
precautions, refer to Important Safety
instructions on page vi.
v
Installation
• The TV should be installed near an
easily accessible power outlet.
• To prevent internal heat buildup, do not
block the ventilation openings.
• Do not install the TV in a hot or humid
place, or in a place subject to excessive
dust or mechanical vibration.
• Avoid operating the TV at
temperatures below 41ºF (5ºC).
• When the TV is transported directly
from a cold to a warm location, or
if the room temperature changes
suddenly, the picture may be blurred
or show poor color due to moisture
condensation. In this case, please wait
a few hours before turning on the TV,
in order to let the moisture evaporate
first.
• To ensure best picture quality, do not
expose the screen to direct illumination
or sunlight. We recommend you use
spot lighting directed down from the
ceiling or to cover the windows that
face the screen with opaque curtains. It
is better that TV is installed where the
floor and walls are not of a reflective
material.
To Customers
To install the specified TV, sufficient
expertise is required. Make sure you
subcontract the installation to ViewSonic
dealer or licensed contractors and
pay adequate attention to safety during
the installation.
Note
This television includes a QAM
demodulator, which should allow you
to receive unscrambled digital cable
television programming via subscription
service to a cable service provider.
The type of programming and signal
provided by your cable service provider
will affect the availability of digital cable
television programming in your area.
Trademark
Information
• Macintosh is a trademark of Apple
Manufactured under license from
Dolby Laboratories.
Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
• HDMI, the HDMI logo and HighDefinition Multimedia Interface are
trademarks or registered trademarks of
HDMI Licensing LLC in the United
States and other countries.
VT3205LED
Important Safety
Instructions
1. Read these instructions completely before using the
equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings.
Install the equipment in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce
heat.
9. Do not attempt to circumvent the safety provisions of the
polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The
wide blade and the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an
electrician for replacement of the outlet.
10. Prevent the power cord from being tread upon or pinched,
particularly at the plug, convenience receptacles, and the
point where they exit from the device. Be sure that the
power outlet is located near the equipment so that it is
easily accessible.
11.Only use attachments/ accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/ apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus when it will be unused for a long
period of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain
or moisture, or the unit does not operate normally, or has
been dropped.
Wiring
For your safety, be sure to unplug the AC power cord when
connecting cables.
Take care not to trip on the cables. It may cause damage to the
TV set.
Electric shock
Do not touch the AC power cord or the TV with a
wet hand. If you plug/unplug the AC power cord
from the TV with a wet hand, it may cause electric
shock.
Lightning storms
During a lightning storm, unplug the TV from the wall outlet and
disconnect the antenna to prevent damage to the TV.
When not in use
If you will not be using the TV set for long periods of time, the
TV set should be disconnected from the AC power outlet to
prevent power line surges. The TV set is not disconnected from
the AC power source when the TV set is switched off.
To disconnect the TV set completely, unplug from the AC power
outlet.
Overloading
This TV set is designed to operate on a 120V
AC supply only. If there are too many appliances
connected to the same AC power outlet, it could
result in a fire or an electric shock.
Optional equipment
If optional equipment is to be installed, leave some space
between optional equipment and the TV set. Picture distortion
and/or noisy sound may occur if the TV set is positioned in close
proximity to any equipment emitting electromagnetic radiation.
Small accessories
Keep small accessories in a safe place where children are unable
to reach.
USE
AC power Cord
Keep the following guidelines to protect the AC power cord from
being damaged. If the AC power cord is damaged, it may result
in a fire or an electric shock. Stop using it and ask your dealer or
ViewSonic service center to exchange it.
• Do not place the TV where the power cord is subject to wear
or abuse.
• Do not pinch, bend, or twist the cord excessively.
• The core lines may be bared and cut, causing a short-circuit,
ViewSonic
vi
VT3205LED
ENGLISH
and resulting in a fire or an electric shock.
• Do not convert or damage the power cord.
• Avoid power cord being rolled over or rested
upon.
• When the power cord is plugged in, do not move the TV.
• Keep the power cord away from heat sources.
• When you disconnect the AC power cord, disconnect it from
the wall outlet first.
• When disconnecting the power cord, grasp the plug instead of
pulling the power cord.
• Use only an original ViewSonic AC power cord, not other
brands.
• Do not use the supplied AC power cord on any other
equipment.
Wall outlet
Insert the plug fully into the outlet. If it is loose,
do not use it. Doing so may cause arcing and
result in a fire. Contact your electrician to change
the outlet.
• This production contains Bitstream Vera Sans fonts under the
following copyright.
Copyright © 2003 by Bitstream, Inc. All Rights Reserved.
Bitstream Vera is a trademark of Bitstream, Inc.
may be removed with a cloth slightly dampened with a solution
of mild soap and warm water. Never use strong solvents such as
thinner or benzine for cleaning. If using a chemically pretreated
cloth, please follow the instruction provided on the package. The
ventilation holes can accumulate dust over time.
To ensure proper ventilation, we recommend you to remove the
dust periodically (once a month) using a vacuum cleaner, while
the LED TV is powered off.
MAGNETIC INFLUENCE
This TV contains a strong magnet in the speaker unit that
generates a magnetic field. Keep any items susceptible to
magnetic fields away from the speaker.
SOUND
If you hear snapping or popping sound comes from
the TV continuously or frequently while the TV is
operating,
unplug the TV and consult your dealer or service
technician. It is normal for some TVs to make occasional
snapping or popping sounds, particularly when being turned on
or off.
CARRYING THE TV
Carry the TV as instructed
To prevent dropping the TV and causing serious injury, you must
follow these guidelines:
• Disconnect all cables before carrying the TV.
• Carrying the large size TV requires at least two or three
people.
• When you carry the TV, place your hands as illustrated and
hold it securely. Do not put stress on the LCD panel and the
frame around the screen.
• When carrying the TV, do not subject it to shocks, vibration,
or excessive force.
• When lifting or moving the TV, hold it securely from the
bottom. Place your palm directly under the panel.
ENGLISH
ANTENNAS
Outdoor antenna grounding
If an outdoor antenna is installed, follow the precautions below.
Do not install the outdoor antenna system near of overhead
power lines or other electric light or power circuits, or where it
can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM,
EXTREME CARE SHOULD BE TAKEN TO KEEP FROM
CONTACTING SUCH POWER LINES OR CIRCUITS AS
CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so that it can provide
some protection against voltage surges and built-up static
charges.
Section 810 of the National Electrical Code (NEC) in the U.S.A.
and Section 54 of the Canadian Electrical Code in Canada
provides information with in regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANS/NFPA 70
Antenna
Ground clamp
Electric service
equipment
Antenna discharge
unit
Ground clamps
Grounding conductors
Power service grounding
electrode system
Batteries
• Do not cast away batteries in a fire.
• Do not disassembled, overheat, or short-circuit the batteries.
• If the battery is replaced in the wrong way, it may cause
danger of explosion. Replace only with the same or
equivalent type.
• Batteries must not be exposed to excessive heat such as
sunshine, fire or the like.
Dispose used batteries
To preserve our environment, dispose of used batteries according
to your local laws or regulations.
VENTILATION
Slots and openings in TV are provided for
ventilation. To ensure reliable operation of the
TV and to protect it from overheating, be sure
these openings are not blocked or covered.
The TV may accumulate dust and get dirty if
proper ventilation is not provided. For proper
ventilation, follow the following guidelines:
• Never install the TV face up, down or
sideways.
• Never install the TV turned over or upside
down.
• Never cover the slots and openings with a
CLEANING
Cleaning the AC power plug
Unplug the AC power plug and clean it
regularly. If the plug is covered with dust and
gathers moisture, its insulation may deteriorate
and result in a fire.
Cleaning the screen surface/ cabinet of
the TV set
When cleaning this TV, unplug the AC power
cord. If not, it may result in electric shock. Use
a dry soft cloth to clean the cabinet of the TV. To remove dust
near the screen, wipe it gently with a soft cloth. Stubborn stains
ViewSonic
vii
VT3205LED
• Do not let this TV get wet. Never spill liquid of any kind on the
TV. If water penetrates into the product, unplug the power cord
and contact ViewSonic.
• Do not operate the TV when wet. It may result in electric shock
or damage to the TV.
• To prevent fire, keep flammable objects or open flame (e.g.
candles) away from the TV.
INSTALLATION
To do Wall mount installation, you need a Wall-Mount Bracket.
When installing or removing the TV using the Wall-Mount
Bracket, be sure to use qualified contractors. If not properly
secured during installation or removal from the Wall-Mount
Bracket, the TV may fall and cause serious injury.
Optional wall mount
• When installing the TV using a Wall-Mount Bracket, make
sure you follow the operating instructions supplied with the
Wall-Mount Bracket.
• Attach the brackets supplied with the Wall-Mount Bracket.
• The TV is not designed for hanging from the ceiling. It may
fall and cause serious injury.
Placement
The TV should be installed near an easily accessible AC power
outlet.
Observe the following to prevent the TV from falling from the
stand or wall mount.
• Place the TV on a stable, level surface.
• Do not hang anything on the TV. Do not allow
children to climb on the TV.
• Do not install the TV in places subject
to extreme temperature, such as in direct
sunlight, near a radiator, or heating vent. If the TV is exposed
to extreme temperature, the TV may overheat and cause
deformation of the enclosure or cause malfunction.
• Do not install the TV in a place exposed to direct air
conditioning.
• If the TV is installed in such a location, moisture may
condense inside and may cause a malfunction.
• Do not place the TV in hot, oily, humid or
excessively dusty places.
• Do not install the TV where insects may
enter.
• Do not install the TV where it may be
exposed to mechanical vibration.
• Do not install the TV in a location where it may spear up,
such as on or behind a pillar, or where you might bump your
head on it. It may cause injury.
Preventing the TV from toppling over
To prevent the TV from toppling over, secure the TV to a wall
or stand.
Placement for watching
We suggest you to watch the TV at a distance of 3-7 times that
of the screen height, and not in excessive brightness. It is easy
to cause eye fatigue if you watch TV for too long or in a dark
room. To obtain clear picture, do not expose the screen to direct
illumination or sunlight. Use spot lighting directed down from
the ceiling if you can.
11.875 inches
(30.16 cm)
4 inches
(10 cm)
4 inches
(10 cm)
4 inches
(10 cm)
Installed with stand
11.875 inches
(30.16 cm)
4 inches
(10 cm)
4 inches
(10 cm)
2.375 inches
(6.03 cm)
Leave at least this space around the set.
Do not install the TV set as follows:
Air circulation is blocked.
Air circulation is blocked.
Objects and ventilation holes
Never push any objects into the slots on the TV cabinet as they
may touch dangerous voltage points or short out parts that could
result in a fire or an electric shock. Do not place any objects on
the TV.
MOISTURE
Moisture and flammable objects
• Keep the product away from moisture. Do not
expose this appliance to rain or moisture. Do not
place objects filled with liquids, such as vases, on
the TV.
• Do not use power-line operated V sets near water,
such as in places like a bathtub, washbowl, kitchen
sink, laundry tub, a wet basement, or near a
swimming pool, etc. It may cause fire or electric
shock.
ViewSonic
viii
VT3205LED
ENGLISH
cloth or other materials.
• Never block the slots and openings by placing the TV on a
bed, sofa, rug or other similar surface.
• Never place the TV in a confined space, such as a bookcase or
built-in cabinet, unless proper ventilation is provided.
Leave some space around the TV set as shown below. Otherwise,
air-circulation may be inadequate and cause overheating, which
may cause a fire or damage to the TV set.
Installed on the wall
ENGLISH
power cord before touching the TV. Otherwise electric shock
may result.
Handling of broken glass and liquid
crystal leakage
If the LCD panel gets damaged, crystalline liquid leakage may
occur, or scattered broken glass may result. Do not touch broken
glass or crystalline liquid which is toxic, with bare hands as
cuts, poisoning or skin irritation may occur. Also do not glass
fragments or leaked crystalline liquid get into your eyes or
mouth. Should either contacted your eyes or mouth, rinse the
contacted area thoroughly with water and consult your doctor.
SERVICING
Do not attempt to repair the TV yourself,
since opening the cabinet may expose you
to dangerous voltage or other hazards. Ask
qualified service personnel to do the servicing
for your TV.
Replacement parts
When replacement parts are required, be sure the service
technician certifies in writing that he/she has used replacement
parts specified by the manufacturer that have the same
characteristics as the original parts. Unauthorized substitutions
may cause a fire, an electric shock or other hazards.
Safety check
Upon completion of repairs to the TV, ask the service
technician to perform routine safety checks (as specified by the
manufacturer) to determine that the TV is safe for operating, and
to so certify.
Ask a qualified service technician to dispose of the TV.
For Customers in the United States
There is mercury in the lamp of this product.
Disposal of these materials may be regulated due to
environmental considerations. For disposal or recycling
information, please contact your local authorities or the
Electronic Industries Alliance (http//www.eiae.org).
Use in outdoor
This TV is not designed for outdoors
installation. Do not expose the TV to rain,
as it may result in a fire or an electric shock.
Also, do not expose the TV to direct sunlight,
as it may heat up and become damaged.
Vehicle, ships and other vessels
Do not install this TV in a vehicle.
Car accidents may cause the TV to fall down and
cause injury.
Do not install this TV in a ship or vessel.
If the TV is exposed to seawater, it may cause a
fire or damage the TV.
Medical institutions
Do not place this TV in a place where medical equipment is in
use. It may cause the medical equipment to malfunction.
VOLUME ADJUSTMENT
• Adjust the volume to avoid disturbing your neighbors.
Sound carries easily at night. Therefore, we suggest you close
the windows or use headphones.
• When using headphones, adjust the volume to appropriate
levels, or hearing damage may result.
LCD SCREEN
• Although the LCD screen is made with high precision
technology and has effective pixels of 99.99% or more, black
dots or bright points or light (red, blue, or green) may appear
constantly on the LCD screen. This is a structural property of
the LCD panel and is not a malfunction.
• The LCD screen is made with high-precision technology. To
achieve a high level of performance and picture quality, this
TV’s backlight setting is set to maximize the brightness of
the TV. However, uneven brightness may be observed when
the LED TV is viewed in a dark environment without an input
source or a blank screen. This is a normal condition, not a
malfunction of the TV. To improve this condition, change the
Picture mode, Backlight setting, enable the Light Sensor, or
turn on the Power management.
• Avoid exposing the LCD screen surface to direct sunlight. It
is likely to damage the LCD panel.
• Do not push or scratch the LCD screen, or place objects on
top of the TV. The image may be uneven or the LCD panel
may be damaged.
• If the TV is used in a cold place, a smear may occur in the
picture or the picture may become dark. It is not caused by a
failure. This condition will improve as the temperature rises.
• When still pictures are displayed continuously, ghosting may
occur. It should disappear after a short period of time.
• The screen and cabinet get warm when the TV is in use. This
is a normal condition.
• Spraying insect repellent with volatile material on the screen
will cause damage.
• Do not make prolonged contact with rubber or plastic
material.
Broken pieces
Do not throw anything at the TV.
Doing so may break the screen glass and cause
serious injury.
If the surface of the TV cracks, unplug the AC
ViewSonic
ix
VT3205LED
ENGLISH
Getting Started
List of Features
1. Brilliant HDTV. Vibrant PC monitor. One innovative display.
2. Stylish design for kitchen, home office, and dorm room.
3. Super HDTV 1366x768 resolution.
4. PC input for computer applications and web surfing.
5. 6 inputs including HDMI/DVI for the latest HD devices.
Package Contents
Please make sure the following items are included with your LCD TV.
If any items are missing, please contact your dealer.
LCD TV
Remote Control
with batteries
ViewSonic
Stand
ViewSonic User Guide
1
Screw
(x2)
Power Cord
ViewSonic Quick Start Guide
VT3205LED
Getting Started
ENGLISH
Installing the LCD TV
Installing the Stand
1. Lay the TV flat on a table with the LCD screen face down. To prevent the TV from being
scratched, put a piece of soft cloth on the table on which the screen will be set. (see Figure 1)
2. Remove the 3 screw from the wall-mount cover. (see Figure 2)
3. Pull off the wall-mount cover slowly. (see Figure 3)
4. Then align the hinge cover from the stand with the back cover like shown above. (see
Figure 4)
5. Use screw driver or other tools (not included) to screw (5 screws total) on the hinge cover.
(see Figure 5)
Disconnecting the Stand
1. Lay the TV flat on a table with the LCD screen face down. To prevent the TV from being
scratched, put a piece of soft cloth on the table on which the screen will be set.
2. Remove the 5 screws from the hinge cover, then pull off the arm slowly, as shown below. (see
Figure 1 and Figure 2)
3. Then connect the wall-mount cover to the back cover like shown below. (see Figure 3)
4. Use the screw driver or other tools (not included) to screw (total of 3). (see Figure 4)
ViewSonic
2
VT3205LED
Getting Started
The LCD TV can be used in a free standing position or wall-mounted. Before installing the product to the
wall, please consider the following guidelines:
• Read the Important Safety Instructions, at the start of this manual.
• Do not install in a moist or wet environment. This equipment is intended for indoor use.
• Do not install near heat source, or strong magnetic fields.
• Use only ViewSonic approved wall-mounting brackets to support the LCD TV weight.
• Before attaching the wall mount plate to the back cover, ensure the product is working.
• If your LCD TV is already set up for free-standing operation, you need to first remove the
stand before mounting the device to the wall.
To attach the wall-mount bracket to LCD TV safely, please use the following guidelines:
• Disconnect the power and any other cables that might hinder moving the LCD TV.
• Set the LCD TV on a table or work surface, placing the screen face down on a towel or
woolen blanket to protect the screen surface from damage while installing plate.
• Before installing the LCD TV on the wall, ensure you have recorded the product serial
number on page (i) of the User Guide, as you will need the serial number to request
service should there be a service need.
• Install the wall mount plate to the LCD TV using screws NO LONGER than 10mm, as
longer screws found in universal (non-ViewSonic) wall mount kits may damage the
power supply causing the unit to fail. The wall-mount screw type is M6 x L10.
• Mount the wall mount bracket to the wall ensuring use of proper screws to support the
installation. Ensure there is at least 3cm of space surrounding any air-vents of your
LCD TV to allow adequate cooling during operation.
• Hang the LCD TV wall mount plate to the wall mount bracket, completing installation.
Enjoy your ViewSonic LCD TV!
ViewSonic
3
VT3205LED
ENGLISH
Mounting ViewSonic LCD TV to the wall
Getting Started
ENGLISH
Wall Mount Kit Specifications (VESA)
When attaching to other building materials, please contact your nearesr dealer.
A
C
B
D
Product Family
LCD TV
inch
VESA Spec. (A x B)
Standard Screw (C x D)
Quantity
16
75 x 75 mm
M4 x L10
4
19 ~ 24
100 x 100 mm
M4 x L10
4
26 ~ 27
200 x 100 mm
M4 x L10
4
32 ~ 37
200 x 100 mm
M6 x L10
4
42 ~ 47
600 x 200 mm
M6 x L10
4
52
400 x 200 mm
M6 x L10
4
• ViewSonic provides the standard dimensions for wall mount kits as shown in the table
above.
• When purchasing our wall mount kit, a detailed install manual and all parts necessary for
assembly are provided.
• Do not use the screws that longer than the standard dimension, as they may cause damage
to the inside of the TV set.
ViewSonic
4
VT3205LED
Getting Started
ENGLISH
Front View of the Product
Item
Description
Lights up in blue when the TV is turned on. Lights up in orange
when the TV is in standby mode.
1
Power LED Indicator
2
Remote Control Receiver Receives IR signals from the remote control.
3
Volume Up
Increase sound volume or adjust a highlighted control while in
OSD menu.
4
Volume Down
Decrease sound volume or adjust a highlighted control while in
OSD menu.
5
MENU
Turn OSD menu ON/OFF.
6
CH Up
Channel up when source is TV, or select a control while in OSD
menu.
7
CH Down
Channel down when source is TV, or select a control while in
OSD menu.
8
INPUT
Select input source.
9
Power ON/OFF button
Turn the power on from standby mode or turn the power off to
return to the standby mode.
ViewSonic
5
VT3205LED
Getting Started
ENGLISH
Rear View of the Product
Item
Description
1
Power (AC input)
Plug-in the supplied AC Power cord and connect to the AC input
power source.
2
RS232 signal input
This port is for the service technician’s use.
3
HDMI 1 Input Terminal
Connect this port to the HDMI output of A/V device.
4
HDMI 2 Input Terminal
Connect this port to the HDMI output of A/V device.
5
PC Audio input
Connect the RGB Audio Out on your computer to the RGB Audio
on the rear of the LCD TV.
6
VGA signal input
Connect a 15-pin D-sub RGB cable to the RGB output of your
computer and the other end to the RGB input on the rear of the LCD
TV.
7
YPbPr signal input
Connect this port to the YPbPr output of A/V device.
8
YPbPr signal Audio
input (left/ right)
Connect the Audio in cable for YPbPr from this jack to the
corresponding connectors on your A/V device.
9
Audio output
Connect this port to your A/V device with audio in (RCA)
connectors or to audio amplifier.
10 AV/ S-Video Audio
input (left/ right)
Connect the Audio in cable for AV/ S-Video from this jack to the
corresponding connectors on your A/V device.
11 Composite Video input Connect this jack to the composite video output connectors on your
A/V equipment.
ViewSonic
6
VT3205LED
Item
Description
12 S-Video input
Connect the S-Video cable from the compatible device to this
connector on the rear panel of the LCD TV.
13 TV Input Jack
Connect this jack to your Cable or VHF/UHF antenna.
14 SPDIF Optical output
Connect this port to the SPDIF input of A/V device.
15 HDMI 3 Input Terminal
Connect this port to the HDMI output of A/V device.
16 Headphone Jack
Connect to your headphones. By connecting the headphones, you can
listen to the sound from the TV on headphones.
*If you connect the headphones, the TV speakers will be muted.
17 USB
Connect to your USB devices, such as USB flash drive.
ENGLISH
Getting Started
AV connection
Connect the composite video and audio input jacks to the corresponding output jacks of your
A/V device.
--- VIDEO: Composite Video input [11]
--- AUDIO: AV/ S-Video signal Audio input [10]
S-Video connection
Connect the S-Video and audio input jacks to the corresponding output jacks of your VCR or
other video device that has S-Video. S-Video provides better picture quality than composite
video connection. If both are connected, S-Video signal has priority.
--- VIDEO: S-Video input [12]
--- AUDIO: AV/ S-Video signal Audio input [10]
Component (YPbPr) connection
YPbPr provides better picture quality than the S-Video or the AV connection.
*For YPbPr connection, connect the component video (YPbPr) and audio jacks to the
corresponding output jacks of your A/V device.
--- VIDEO: YPbPr signal input [7]
--- AUDIO: YPbPr signal audio input [8]
HDMI connection
HDMI (High-Definition Multimedia Interface) is a licensable audio/video connector interface
for transmitting uncompressed, encrypted digital streams between this TV and any HDMIequipped audio/video equipment.
*Be sure to use only an HDMI cable that bears the HDMI logo.
*If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDMI
Input Terminal (with DVI-to-HDMI cable or adapter), and connect the Audio cable to the
Audio In jacks.
HDMI cable
DVI-to-HDMI cable
DVI-to-HDMI adapter
Audio cable
ViewSonic
7
VT3205LED
Getting Started
ENGLISH
1. With HDMI cable: HDMI1 Input Terminal [3] , HDMI2 Input Terminal [4], or HDMI3
Input Terminal [15]
2. With HDMI-DVI cable
--- VIDEO: HDMI1 Input Terminal [3]
--- AUDIO: PC Audio input [5]
--- VIDEO: HDMI2 Input Terminal [4]
--- AUDIO: PC Audio input [5]
or
--- VIDEO: HDMI3 Input Terminal [15]
--- AUDIO: PC Audio input [5]
Computer connection
Connect the VGA cable and Audio cable from the VGA signal input and PC Audio input to
the corresponding ports on your A/V device.
--- VIDEO: VGA signal input [6]
--- AUDIO: PC Audio input [5]
ViewSonic
8
VT3205LED
Getting Started
ENGLISH
Connecting the LCD TV
Cable System or VHF/UHF Antenna System
Enjoy the high-definition and standard-definition digital programming along with standarddefinition analog programming.
☼
• This TV is capable of receiving unscrambled digital programming for both cable and
external VHF/UHF antenna.
• We strongly recommend that you connect the antenna/cable input using a 75-ohm coaxial
cable (not supplied) to ensure the best picture quality.
Cable or VHF/UHF
75-ohm coaxial cable
Rear of TV
VHF/UHF/CABLE input
Cable System and VHF/UHF Antenna System
Use an optional A-B RF switch (not supplied) to switch between the cable and antenna
programming, as shown below.
A-B RF switch
Cable
Rear of TV
Antenna
VHF/UHF/CABLE input
☼
• Remember to set the TV/CATV setting in the TV menu to Air or Cable for the type you
choose.
HD Cable Box/HD Satellite Box
You can also enjoy high-definition programming by subscribing to a high-definition cable
service or a high-definition satellite service. For the optimum picture quality, be sure to
connect this device to your TV via the HDMI or component video (with audio) input on the
back of your LCD TV.
HDMI Connection
Rear of TV
or
HD cable box/
HD satellite box
or
HDMI cable
ViewSonic
9
CATV/Satellite
antenna cable
VT3205LED
Getting Started
DVI Connection
ENGLISH
Rear of TV
HD cable box/
HD satellite box
or
or
Audio cable
DVI-to-HDMI cable
CATV/Satellite
antenna cable
☼
• If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the
HDMI1 jack [3], HDMI2 jack [4] or HDMI3 jack [15], and connect the audio jack to
the AUDIO In jacks of PC Audio input [5].
YPbPr or Component Connection
Rear of TV
HD cable box/
HD satellite box
Audio cable
CATV/Satellite
antenna cable
Component video cable
ViewSonic
10
VT3205LED
Getting Started
Personal Computer
ENGLISH
Use the LCD TV as the monitor of your computer.
The picture below shows the connection for PC. The LCD TV can also be connected to PC
with DVI or HDMI output.
Connect to an HDMI compatible PC
with the HDMI cable.
Rear of TV
Audio cable (stereo mini plugs)
VGA 15 Pin cable
☼
• Connect the PC IN jack to the PC using a 15-pin cable and audio cable.
• If the PC is connected to TV and no signal has been input from PC for more than 5 seconds,
the TV will enter standby mode automatically.
PC Timing Reference Chart
Mode
Aspect Ratio Handling
Compatible Input
FS*Full-Screen
RGB
720 x 400 @ 70Hz
1360x768
Yes
VESA
640 x 480 @ 60Hz
1360x768
Yes
VESA
640 x 480 @ 75Hz
1360x768
Yes
VESA
800 x 600 @ 60Hz
1360x768
Yes
VESA
800 x 600 @ 75Hz
1360x768
Yes
MAC
832 x 624 @ 75Hz
1360x768
Yes
VESA
1024 x 768 @ 60Hz
1360x768
Yes
VESA
1024 x 768 @ 75Hz
1360x768
Yes
VESA
1280 x 960 @ 60Hz
1360x768
Yes
VESA
1280 x 1024 @ 75Hz
1360x768
Yes
VESA
1360 x 768 @ 60Hz
1360x768
Yes
Standard
Resolution
☼
• This TV’s PC VGA input does not support interlaced signals.
• For the best picture quality, we recommend that you use the signals (boldfaced) in the
above chart with a 60 Hz vertical frequency from a personal computer.
ViewSonic
11
VT3205LED
Getting Started
ENGLISH
Other Equipment
Amplifier/ VHF/ UHF
DVD Home CABLE
Theater
DVD Player/
Personal
Computer
Personal
Computer
DVD Player/
VCD Player/
Game system
Amplifier/
DVD Home
Theater
DVD Player/
Digital VCD Player/
Blu-ray Disc satellite Game system
Player/ PS3 receiver
AC power
socket
Digital
Personal
cable box Computer
DVD Audio
Player system
USB Device
Headphone
DVD Player/
VCD Player/
Game system
Blu-ray Disc Digital satellite
Player/ PS3 receiver
Digital
cable box
Personal
Computer
DVD
Player
Audio
system
☼
• Please refer to the Quick Start Guide (supplied) when connecting the other equipment to
your LCD TV.
ViewSonic
12
VT3205LED
Using the TV Features
ENGLISH
Remote Control and TV Controls
Inserting Remote Control Batteries
1. Remove the battery cover by pulling then lifting the knob on the cover.
2. Insert the batteries, corresponding to the (+) and (-) markings on the battery compartment.
3. Reattach the battery cover.
CAUTION
• Only use the specified AAA batteries.
• Do not mix new and old batteries. This may result in creaking or leakage, which may pose
a risk of fire or lead to personal injury.
• Insert batteries according to (+) and (-) markings. Inserting the batteries incorrectly may
result in leakage, which may pose a risk of fire or lead to personal injury.
• Dispose of the battery in accordance with local laws and regulations.
• Keep the batteries away from children or pets.
• When the remote control will not to be used for an extended period, remove the batteries.
Remote Control and TV Controls
Buttons located at the side of the LCD TV will operate the same as
these buttons on the remote control.
ViewSonic
Button
Description
1
POWER
Press this button to turn the power on from standby
mode. Press it again to return to the standby mode.
2
INFO
Press this button to display the current state of the
LCD TV.
13
VT3205LED
ENGLISH
Using the TV Features
Button
Description
3
TV
Press to direct to TV source when in any other
source.
4
0~9, number
buttons
Press 0~9 and “-” to select a channel. After you
input the channel numbers, press ENTER button
to direct to the channel immediately, or wait for 3
seconds to change automatically.
5
C.C
Press to select the Closed Caption menu in the TV
, AV, S-video mode.
6
- VOL +
Press to adjust the volume.
7
GUIDE
Press to display the Electronic Program Guide
(EPG). It contains the program information for the
channel you’re watching.
*The picture here shows an example of the GUIDE
screen in a DTV source.
8
FAV
Press this button to show Favorite List and select your
favorite channels that have already been stored.
*To preset favorite channels, use the Favorite item
in the Channel menu.(see page 19)
9
ViewSonic
▲▼◄►/
ENTER
buttons
Press these buttons to navigate the OSD menus.
▲/▼ is for menu and function select, and ◄/► is
for function adjustment.
ENTER: Enter the function setting.
14
VT3205LED
Button
Description
10 INPUT
Press to display the INPUT source list and select
the source with ▲/▼ buttons. To confirm the
selection, press ENTER.
11 SOUND
Press this button to select between the sound
modes of Standard, Music, Movie, Sports or
Personal.
ENGLISH
Using the TV Features
12 PICTURE Press this button to select between the picture
modes of Standard, Dynamic, Soft, or Personal.
ViewSonic
13 MTS
Press this button to choose the available sound
output that is preset by TV broadcasting station.
(EX: Mono, Stereo, SAP)
14 MUTE
Press to turn off the sound. To restore the sound,
press this button again, or press the VOL+/button.
15 RETURN
Press to return to previous channel.
16 ▼ CH ▲
Press to change the channels up or down.
17 EXIT
OSD exit
18 MENU
Press to turn the OSD (On-Screen Display) menu
on.
19 SLEEP
Press repeatedly to set the off timer. The function
is used to automatically shut off the LCD TV after
a preset period of time passed. There are several
times for choice – Off, 5 Min, 10 Min, 15 Min, 30
Min, 45 Min, 60 Min, 90 Min, 120 Min, 180 Min,
240 Min.
20 ASPECT
Press this button repeatedly to select the screen size.
You can select from Normal, Movie Scale, Zoom
In, and 4:3.
15
VT3205LED
Using the TV Features
ENGLISH
Operation
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the Power button on the side of the panel.
*If there is no input signal within 15 minutes, TV will be
turned off automatically.
Initial Setup
(Setup Wizard only appears when first turning the TV on and without channel scanning.)
1. Press the POWER button on the remote control. The Setup Wizard window will be display.
2. Press ◄ or ► to select OSD language, then press ENTER or ▼ to confirm the
selection, and press ► or ENTER to go to next step. To return to the previous page, press
MENU.(See Figure1)
3. Press ◄ or ► to select your display mode from *Home, Medium, Low or High, then
press ENTER or▼ to confirm the selection, and press ► or ENTER to go to next step. To
return to the previous page, press MENU. (See Figure2)
* For normal home use, we suggest that you select “Home” to achieve energy saving.
4. Select Time Zone of your location. To press ▼ to setup DST (Daylight Saving Time) and
select On or Off with ◄ or ►, according to the time zone of your area. To press ▼ to setup
Time Format, and select 12-hour or 24-hour with ◄ or ►, then press ENTER or ► to
continue. (See Figure3)
5. Select TV Source from Air or Cable, then press ENTER to continue. (See Figure4)
6. The Initial Setup will be completed after Cannel scanning is finished. To interrupt the
scanning, press MENU at any time. (See Figure5)
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
ViewSonic
16
VT3205LED
Using the TV Features
ENGLISH
Changing Channels
1. Using Channel Buttons
Press ▼CH▲ button to change channels, and the TV
changes channels in sequence. You will see all channels
that have been memorized. Channels erased or not
memorized will not be shown.
2. Using Number Buttons
(1) ATV
The “-” button has no function in ATV mode. Directly
press the number buttons to select channels.
(2) DTV
Use “-” button to select the sub channel in DTV.
Ex: Your desired number is 80-3.
Press 8 → press 0 → press “-” → press 3.
*Return to the previous channel, press RETURN
button.
Adjusting the Volume
Press VOL +/- to adjust volume.
To turn off the volume, press MUTE.
To restore volume, press MUTE again, or press
VOL +/- directly.
Viewing the Displayed Information
To display the current information of the LCD TV:
Press INFO, and the current state will be displayed on
the screen. (It shows all or some of the information about
Input, Channel, Resolution, Audio Type, etc., depending
on what input source it is in)
*The picture here shows an example of the INFO screen
in a DTV source.
ViewSonic
17
VT3205LED
Using the TV Features
ENGLISH
Storing Channels into Memory
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select the “CHANNEL” menu, then press ENTER or ▼ to enter the menu. Press ▲ or ▼
to select “TV Source”, and use ◄ or ► to select the
antenna connection to “Air” or “Cable”.
Air: RF signal programs by “Air”.
Cable: RF signal programs by “Cable”.
3. Press ▲ or ▼ to select “Auto Scan”, then press ► to
enter.
4. Press ▲ or ▼ to select “Scan all channels”, “Digital
channel only”, or “Analog channel only” and press ► to
perform Auto Scan function.
To stop scanning, press MENU at any time.
5. The Auto Scan screen will be shown, and after it is
done, the screen will return to the first found channel.
Viewing the Menus
1. Press the MENU button to display the OSD main menu.
There are six top menus on the screen: PICTURE,
AUDIO, TIME, OPTION, LOCK, and CHANNEL.
( CHANNEL menu can only be enabled in TV
source.)
2. Press ◄ or ► to select your desired top menu.
3. Press ENTER or ▼ to enter the menu you select.
4. Use ▲▼ to select the control you want to adjust.
5. When selecting the control with ►, press ► to enter
next level menu or enable the function. (► will only
appear when the control is highlighted)
6. Press ◄► to adjust or select the settings.
7. Press MENU to exit from the OSD menu.
ViewSonic
18
VT3205LED
Using the TV Features
ENGLISH
Selecting the Input Source
To select the TV or other external input sources connected
to the TV.
1. Press the INPUT button on the remote control.
2. Press ▲ or ▼ to select the required input source between
TV, AV, S-Video, YPbPr, HDMI1, HDMI2, HDMI3,
PC or USB.
(When in USB input source, the system only supports
JPEG, BMP and PNG image files.)
3. To confirm the selection, press ENTER.
Favorite Channel Setting
To set your favorite channel into memory:
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select the “CHANNEL” menu, then
press ENTER or ▼ to enter the menu. Press ▲ or ▼
to select “Favorite”, then press ► button to
enter “Favorite” setting.
3. Press ▲ or ▼ to select the channel you’d like to be your
favorite channel.
Press ENTER to confirm your selection.
4. To cancel the selection, Press ENTER again on the selected
channel.
5. Press MENU to exit.
*To view your favorite channels, press FAV button to
show Favorite List and select your favorite channels that
have already been stored.
ViewSonic
19
VT3205LED
ENGLISH
Using the TV Features
Adding/Erasing Channel
When the channel is erased, it will not appear on the
screen when you browse the channels with ▼CH▲
button. To see the channel again, you must add the channel
or perform the “Auto Scan” (page 19) function again.
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select the “CHANNEL” menu, then
press ENTER or ▼ to enter the menu. Press ▲ or ▼ to
select “Show/Hide”, then press ►
button to enter “Show/Hide” setting.
3. Press ▲ or ▼ to select the channel you want to Show/
Hide, and check or uncheck it with ENTER button.
4. Press MENU to exit.
Channel Name Setting
To edit a name for the current channel:
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select the “CHANNEL” menu, then
press ENTER or ▼ to enter the menu.
3. Press ▲ or ▼ to select “Channel No.”, then press ◄ or ►
to select the channel you want to edit the name.
4. Press ▲ or ▼ to select “Channel Label”, then press ►
button to enter “Channel Label” setting.
5. Use ▲ or ▼ to choose letters or signs, ◄ or ► to move
forward or backward.
6. After you input the channel name, press MENU or
ENTER to complete the setting.
7. Press MENU to exit.
ViewSonic
20
VT3205LED
Using the TV Features
ENGLISH
Adjusting the Settings
1.
(1) Press the MENU button to display the OSD main menu.
(2) Press ◄ or ► to select your desired top Menu, then
press ENTER or ▼ to enter the menu.
(3) Press ▲ or ▼ to select the control of “Contrast”,
“Brightness”, “Sharpness”, “Tint”, “Color”,“Bass”,
“Treble”,“Balance”,then press ◄ or ► to adjust
the level.
(4) Press MENU to exit.
2.
(1) Press the MENU button to display the OSD main menu.
(2) Press ◄ or ► to select your desired top Menu, then
press ENTER or ▼ to enter the menu.
(3) Press ▲ or ▼ to select the control of “Picture Mode”,
“Color Mode”, “Aspect Ratio”, “Noise Reduction”,
“Sound Mode”, “MTS”, “Audio Language” (only in DTV
mode), “SRS TruSurround HD”, “Audio Only”, “Sleep
Timer”, “Time Zone”, “DST”, “Time Format”, “Auto
Sync”, “Menu Language”, “Transparent”, “OSD Time
Out”, “DCR” (Dynamic Contrast Ratio), “Backlight”,
“TV ID”, “TV Source”,“Channel No.”,then press ◄ or
► to select your desired option.
(4) Press MENU to exit.
3.
(1) Press the MENU button to display the OSD main menu.
(2) Press ◄ or ► to select your desired top Menu, then
press ENTER or ▼ to enter the menu.
(3) Press ▲ or ▼ to select the control with ►, including
“Clock”, “Closed Caption”, “Restore Default”,“Input
Label”,“Auto Scan”, “Favorite”, “Show/Hide”,
“Channel Label”, then press ► to perform the
function or enter detailed settings.
ViewSonic
21
VT3205LED
ENGLISH
Using the TV Features
Setting up Time menu
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select the “TIME” menu, then
press ENTER or ▼ to enter the menu.
3. Press ▲ or ▼ to select “Sleep Timer”, and press ◄ or
► to set the “Sleep Timer” from 5~240 min, or Off.
4. Press ▲ or ▼ to select “Time Zone”, and select the correct
time zone of your area with ◄ or ►. The displayed time
of “Clock” will be changed at the same time automatically.
To adjust “Clock”, select “Clock” and press ►. Use ◄
or ► to change between year/ month/ date/ hour/ minute,
▲ or ▼ to adjust. When you finish adjustment, select
“OK” and press ENTER to complete the setting.
*The “Clock” time can only be adjusted manually
when “Auto Sync” is set to “Off”.
5. Press ▲ or ▼ to select “DST” (Daylight Saving Time),
and select On or Off with ◄ or ► according to the time
zone of your area. The “Clock” time will change
automatically.
6. Press ▲ or ▼ to select “Time Format”, and ◄ or ► to
select 12-hour or 24-hour.
7. Press MENU to exit.
Closed Caption Setting
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select the “OPTION” menu, then
press ENTER or ▼ to enter the menu.
Press ▲ or ▼ to select “Closed Caption”, then press ►
button to enter “Closed Caption” setting.
3. Press ▲ or ▼ to select CC Mode, Basic Selection, or
Advanced Selection, and use ◄ or ► to make your choice.
Basic Selection: To set basic analog closed caption
options. (CC1~CC4, TEXT1~TEXT4, Off)
Advanced Selection: To select closed caption signal
formats and set up caption modes for digital TV
channels. (Service1~6, Off)
ViewSonic
22
VT3205LED
Using the TV Features
ENGLISH
For detailed Close Caption setting:
1. Press ▲ or ▼ to select “Option”, then press ► to enter
“Option” setting.
2. Press ◄ or ► to select the Mode to be “Custom”, and then
use ▲ or ▼ to select desired options and use ◄ or ► to
adjust detailed settings.
*When you select the Mode to be “Default”, you can
not adjust the detailed settings.
Using the Parent Controls
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select the “LOCK” menu.
3. Press ENTER or ▼ to enter Password.
4. Enter the password. (The default password is 0000)
5. Move to “System Lock”, and select “On” to enable the
detailed settings.
6. Move to “US” or “Canada” rating system.
ViewSonic
23
VT3205LED
ENGLISH
Using the TV Features
US: Press ► to set TV or MPAA ratings.
(1) TV
1. Press ▲ or ▼ to select “TV”, then press ►
to enter “TV” rating system setting.
2. Press ▲ or ▼ to select your desired TV ratings
level.
The following screen will allow you to customize
the following TV ratings:
Y (all children)
Y7 (older children)
G (general audience)
PG (guidance suggested)
14 (strongly cautioned)
MA (mature audience)
You can also customize the TV ratings for the
following content:
ALL (All types content)
FV (fantasy violence)
V (violence)
S (sexual situations)
L (adult language)
D (sexsual dialog)
3. Press ENTER to set or reset each area.
4. Press MENU to exit.
(2) MPAA
1. Press ▲ or ▼ to select “MPAA”, then
press ► to enter “MPAA” rating system setting.
2. Press ▲ or ▼ to select your desired MPAA ratings
level.
The MPAA ratings level are defined as following:
G (general audience)
PG (parental guidance suggested)
PG-13 (recommended for children 14 years of age
or older)
R (mature audience)
NC-17 (no one under 17 years of age)
X (adult audience only)
N/A (not applicable)
3. Press ▲/▼ to set or reset each area.
4. Press MENU to exit.
ViewSonic
24
VT3205LED
Using the TV Features
ENGLISH
Canada: Press ► to set Canadian English and French
ratings.
(1) Canadian English
1. Press ▲ or ▼ to select “Canada Eng”.
2. Press ► to enter.
3. Press ▲ or ▼ to select your desired Canadian
English rating level.
The Canadian English rating levels are defined as
following:
C (children)
C8+ (children eight years and older)
G (general programming, suitable for all audiences)
PG (parental guidance)
14+ (viewers and older)
18+ (adult programming)
EXEMPT (exempt)
4. Press ▲/▼ to set or reset each area.
5. Press MENU to exit.
(2) Canadian French
1. Press ▲ or ▼ to select “Canada Fre”.
2. Press ► to enter.
3. Press ▲ or ▼ to select your desired Canadian
French rating level.
The Canadian French rating levels are defined as
following:
G (genenral)
8ans+ (children eight years and older)
13ans+ (not appropriate for children of less than 13
years)
16ans+ (not appropriate for children of less than 16
years)
18ans+ (reserved to adults)
EXEMPT (exempt)
4. Press ▲/▼ to set or reset each area.
5. Press MENU to exit.
ViewSonic
25
VT3205LED
ENGLISH
Using the TV Features
To Block Unrated Movie or TV Programs
1. Press ▲ or ▼ to select “Unrated Lock”, then press ◄
or ► to select “On” or “Off”. When “On” is selected,
all programs that are not rated will be blocked.
2. Press MENU to exit.
To Set Rating Region Table
RRT Setting defines the rating standard for a particular
geographic region and/ or country.
1. Press ▲ or ▼ to select “RRT Setting”, then press ► to
enter RRT setting.
2. Select each adjustable setting with ▲ or ▼, then press
◄ or ► to select the sub-selection.
3. Press MENU to exit.
*The picture here only shows an example of the content
of RRT Setting. However, the selections and subselections of RRT Setting may be different in your OSD
menu according to the local broadcasting system.
*To reset RRT setting, move to “Reset RRT”, and press
► to reset.
To Change Password
1. Press ▲ or ▼ to select “Change Password”, then press
► to enter “Change Password” setting.
2. Move to “Enter Old Password”, then enter the old
password with number keys.
3. Enter your new password on “Enter New Password”.
4. Enter your new password again on “Confirm Password”.
After you complete the last step, the screen will return to
the top page of LOCK menu. If so, the password has been
changed successfully.
ViewSonic
26
VT3205LED
Using the TV Features
ENGLISH
To block by Input Source
1. Press ▲ or ▼ to select “Input Block”.
2. Press ▲ or ▼ to select the input source, then ◄ or ►
to select from “Block” or “UnBlock”.
3. Press MENU to exit.
To Restore Factory Setting
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select the “OPTION” menu.
3. Press ENTER or ▼ to enter “OPTION” menu.
4. Press ▲ or ▼ to select “Restore Default”, then press ►
to restore the factory default setting.
5. Select “Yes” and press ENTER to confirm the setting.
Setting RS232 Parameter
1. Press the MENU button to display the OSD main menu.
2. Press ▲ or ▼ to select the “OPTION” menu.
3. Press ENTER or ► to enter “OPTION” menu.
4. Press ▲ or ▼ to select “TV ID”, then press ◄ or ►
to set the TV ID number from 01~98. For detailed
information, refer to the RS232 Protocol on page 37~47.
ViewSonic
27
VT3205LED
ENGLISH
Using the TV Features
Using PC Function
1. When in PC source, press the MENU button to display
the OSD main menu.
2. Press ◄ or ► to select the “PICTURE” menu, then
press ENTER or ▼ to enter the menu.
3. Press ▲ or ▼ to select your desired controls, and press
◄ or ► to adjust.
4. For advanced PC functions, select “Advanced” (only
in PC source) and press ► to enter.
5. Press ▲ or ▼ to select “H-Pos” (H-Position), “V-Pos”
(V-Position), “Clock”,“Phase” or “Auto” (Auto
adjustment), and adjust the level with ◄ or ►.
* When in PC source, the other menus are the same as or
similar to when in other source.
* When there is no signal in the PC mode, “No Signal” will
be displayed on the screen and the TV will automatically
turn into power-saving mode after a few seconds’ idleness.
Press INPUT or POWER button on the remote control
and the TV will return to VGA mode.
ViewSonic
28
VT3205LED
Using the TV Features
ENGLISH
Using USB Function
1. When input source is selected to USB, insert the USB
device into the USB jack. USB only supports JPEG,
BMP and PNG image files (With symbol).
2. Use ▲ or ▼ to select the folder you want, and press
ENTER (See Figure1).
3. Return to main menu, press ▲ or ▼ to ”--“ and press
ENTER (See Figure 2). Use ▲ or ▼ to select the
image files you want, and press ENTER (See Figure 3).
Figure1
In USB mode, you can use the buttons to make
following functions:
Press INFO can view all of the functions (See Figure 4)
* Press EXIT go back to the previous page.
* Use ► or ◄ to display the next or previous picture.
* Use ▲ or ▼ to rotate right or rotate left the picture.
(Only available in X1.0 mode)
* Press Aspect to zoom in. (X1.5~X4.0)
* When the Aspect Ratio, press ▲▼◄► to move.
* Press ENTER to auto-play or stop the pictures.
In “Option” menu can setup following functions:
1. Press the MENU button to display the OSD main menu.
2. Press ◄ or ► to select “Option” menu, then press
ENTER or ▼ to enter the menu. Press ▲ or ▼ to
select “Media”, and use ► to enter “Media” setting.
•SlideShow Timer:
To select the pictures auto-play interval time.
•Trans. Effect:
To select the auto-play effects of the slide show.
•File List Sorting:
To select the pictures arrange.
•SlideShow Repeat:
To select the slide show repeat to On or Off.
ViewSonic
29
Figure2
Figure3
Figure4
VT3205LED
Using the TV Features
ENGLISH
Annotations for OSD Menu Items
See below for meanings of the control items in each menu.
Picture menu
• Picture Mode: To select picture mode.
• Contrast: To adjust contrast of video.
• Brightness: To adjust luminance of video.
• Sharpness: To adjust picture sharpness.
• Tint: To adjust tint level.(Except PC source)
• Color: To adjust color.(Except PC source)
• Color Mode: To select and adjust color mode.
• Aspect Ratio: To select image size between Normal,
Movie Scale, Zoom in and 4:3.(Except PC and USB
source)
• Noise Reduction: To reduce the noise level of connected
equipment.(Except PC source)
• Advanced: To fine tune the image. (Only enabled in
PC source)
* H. Pos: To adjust the horizontal position of the
picture.
* V. Pos: To adjust the vertical position of the picture.
* Clock: To adjust delay time of clock in order to
reduce the noise of picture.
* Phase: To adjust delay time of phase in order to
reduce the noise of picture.
* Auto: To auto adjust picture’s horizontal position,
vertical position, clock, phase, fine tune and H-Size.
Audio menu
• Sound Mode: To select Sound modes.
• Bass: To adjust bass.
• Treble: To adjust the treble.
• Balance: To adjust left and right audio balance.
• Audio Language: To select available audio language.
(Only available in DTV)
• SRS TruSurround HD: To select “SRS TruSurround
HD” effect or not.
• Audio Only: To turn off the screen picture but keep the
sound on.
• MTS: To select audio mode.(EX: Mono, Stereo, SAP)
(Only available in ATV)
ViewSonic
30
VT3205LED
Using the TV Features
ENGLISH
Time menu
• Sleep Timer: To set the off timer.
• Time Zone: To select the time zone appropriate to
your location.
• DST: To turn on/off daylight saving.
• Time Format: To select 12-hour or 24-hour.
• Auto Sync: To turn on/off Auto Sync.
• Clock: To set the clock.
Option menu
• Menu Language: To select OSD language.
• Transparent: To select OSD (On Screen Display)
transparent level.
• OSD Time Out: To select OSD show time.
• Closed Caption: To set close caption options.
(Only available in TV, AV, S-Video source)
• Restore Default: To restore the factory default settings.
• Input Label: To Change the input source name.
• DCR: To turn on/off the DCR (Dynamic Contrast Ratio)
function.(Except USB source)
• Backlight:To select backlight brightness between Home,
Medium, Low, and High.
• Over Scan: To select this function to On or Off in
HDMI1, HDMI2 and HDMI3.(Only available when
input signal is in video timing. Ex:480i, 480p, 720p,
1080i)
• Media: To set the picture slide show setting.(Only
available in USB source)
• TV ID: Setting RS232 Parameter.
ViewSonic
31
VT3205LED
ENGLISH
Using the TV Features
Lock menu
• Change Password: To Change the current Password.
• System Lock: To select On or Off to Lock parent
control.
• Unrated Lock: To block unrated movie or TV
programs.
• Input Block: To block by input source.
• US: Select TV and MPAA to set the parent control.
• Canada: Select Canadian English and Canadian French
to set the parent control.
• RRT Setting: To set Rating Region Table.
• Reset RRT: To reset Rating Region Table.
Channel menu
• TV Source: To select TV source. Select “Cable” to
watch cable TV channels, and select “Air” to watch air
TV channels.
• Auto Scan: To auto scan ATV and DTV channels.
• Favorite: To set your favorite channel into memory .
• Show/Hide: To set the cannel show or hide.
• Channel No.: To select the cannel you want to edit the
name.
• Channel Label: To edit a name for the current cannel.
• DTV Signal: To display the detected signal strength of
the current DTV channel.
ViewSonic
32
VT3205LED
Other Information
ENGLISH
Cleaning the LCD TV
• Make sure the LCD TV is turned off.
• Never spray or pour any liquid directly onto the screen or case.
To clean the screen:
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean,
soft, lint-free cloth, and wipe the screen.
To clean the case:
1. Use a soft, dry cloth.
2. If still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild non-abrasive
detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the LCD TV screen
or case. Some chemical cleaners have been reported to damage the screen and/or case of the LCD TV.
ViewSonic will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners.
Programming your Cable or Satellite Box remote
Refer the user manual from your service provider to determine the setting.
If it requires:
• 3 digits, please try “566”, “565”, “556”, or “688”. It usually works with DISHNetwork.
• 4 digits, please try “0054”. It usually works with Cox.
• 5-digits, please try “11454”, “11054”, or “10690”. It usually works with DIRECTV.
ViewSonic
33
VT3205LED
Other Information
ENGLISH
Troubleshooting
Please contact ViewSonic service team directly if you have questions, service needs, or require technical
assistance related on the use of your television.
Contact ViewSonic Service Team at:
http://www.ViewSonic.com
Or call our service team:
United States 1-800-688-6688
Canada 1-866-463-4775
Problem
Possible Solution
No power
• Make sure the power cord is properly connected to the
LCD TV AC power socket.
• Make sure the AC power cord is properly connected to the
wall outlet.
• Make sure the DC power button is ON (Blue LED).
• Plug another electrical device (like a radio) to the power
outlet to verify that the outlet is supplying the proper voltage.
No picture
• The TV station may be experiencing problems. Try another
channel.
• The Cable TV signal may be scrambled or encoded. Please
contact your local cable operator.
• Make sure that connection to other components are correct
referring to the user guide.
• Make sure that setup has been done correctly after
connections.
• Make sure the correct input is selected and the input signal is
compatible.
Strange color, light color,
or color misalignment
• Ensure that the video cable is securely connected.
• The picture may appear dim in a brightly lit room.
• Adjust brightness, contrast, saturation (color), and tint
referring to the user guide.
• Check the input signal setting.
No sound
• Check your audio connections are properly connected
referring to the user guide.
• The MUTE button may have been pressed, try pressing this
button again.
• Check your audio settings, your TV audio may be set to
minimum.
• Press the Volume + (Up) button on the remote control.
ViewSonic
34
VT3205LED
Problem
Possible Solution
Remote control unit does not
operate
• Make sure the directions of batteries are inserted correctly
referring to the user guide.
• Batteries could be weak or dead. Replace with new batteries.
• Is a fluorescent light illuminated near the remote control
sensor?
• The path of the remote control beam may be blocked. Make
sure the path is clear and that the remote control is aimed at
the remote control sensor on the TV.
• Press the POWER button on the remote control to see if you
can turn on the TV.
• Press MENU button on the remote control to see if there is a
MENU shown on the screen.
• Press only one button at a time and it is the correct one for
the operation you want to perform.
Unit cannot be operated
• External influences such as lightning or static electricity may
cause improper operation. In this case, operate the unit after
first turning on the power of the LCD TV and the AVC
System, or unplug the AC cord for 1 to 2 minutes, then
replug again.
Power is cut off suddenly
• Is the sleep timer set in advance?
• Is there no signal in PC mode or HDMI mode?
• The internal temperature of the unit has increased. Remove
any objects blocking the vent or clean as necessary.
No CATV reception (or no
reception above CH13)
• Is the AIR/CABLE option set correctly? Please set the AIR/
CABLE option to CABLE referring to the user guide.
• CATV is connected improperly or not connected; please
check all the CATV connections.
• The cable TV service is interrupted; please contact your
cable operator.
Picture is cut off/with sidebar
screen
• Is the image positioned correctly?
• Are screen mode adjustments such as picture size set
correctly?
• Press WIDE button repeatedly on the remote control to see if
you can get the picture you prefer.
ViewSonic
35
VT3205LED
ENGLISH
Other Information
Other Information
ENGLISH
Specifications
Model
LCD
(LED Backlight)
Input signal
VT3205LED
Type
31.51” TFT Active Matrix RGB
0.17025 (H) x 0.51075 (V) mm pixel
Color Filter
Glass surface
RGB vertical stripe
Anti-Glare
RGB
RGB analog (0.7/1.0 Vp-p, 75 ohms) Separate Sync,
fh: 30-82 kHz, fv:55-76 Hz
TV system Antenna / NTSC+ATSC, TV cable system /
CATV+Digital cable
1 composite RCA, 1 S-Video, 1 YPbPr component, 3 HDMI
RF
Video
Audio
1 mini-stereo,
2 pair of RCA (L/R) stereo
USB
JPEG / BMP / PNG Picture Format
Compatibility
PC
Up to 1360 x 768 @ 60 Hz, VGA mode
Resolution
Recommended
and supported
(VGA mode)
1360 x 768 @ 60 Hz
1280 x 1024 @ 75 Hz
1280 x 960 @ 60 Hz
1024 x 768 @ 60, 75 Hz
800 x 600 @ 60, 75 Hz
640 x 480 @ 60, 75 Hz
Speaker Output
10W x 2 @ THD=10%
Audio Output
1 Headphone jack, 1 stereo RCA jack, 1 SPDIF (optical)
Power
Voltage
100-240 VAC, 50/60 Hz (auto switch)
Display area
Full Scan
697.68mm (H) x 392.26mm (V)
27.47” (H) x 15.44” (V)
Operating
conditions
Temperature
Humanity
Altitude
32°F to + 104°F ( 0°C to + 40°C)
10% to 65% (no condensation)
To 6,500 feet (2,000m)
Storage
condition
Temperature
Humanity
Altitude
-4°F to + 140°F (-20°C to + 60°C)
0% to 90% (no condensation)
To 40,000 feet (12,000m)
Dimensions
Physical
(W) x (H) x (D)
774.7mm x 563.6mm x 210.0mm 30.5’’ x 22.19’’ x 8.27’’
Weight
Net
9.6 kg (21.16 lb)
UL/cUL, FCC-B (Doc-B), NOM, BETS-7, ENERGY STAR®, NRCan
Regulations
Power
consumption
On
Stand by
< 130 W [Max] (blue LED)
< 1 W @ 115 Vac only (orange LED)
Warning: Do not set the graphics card in your computer to exceed these refresh rates; doing so may result in
permanent damage to the LCD TV.
Note: Product Specifications are subject to change without notice.
ViewSonic
36
VT3205LED
Other Information
RS232 Protocol
This document describes the hardware interface spec and software protocols of RS232 interface
communication between Viewsonic Commercial Display and PC or other control unit with RS232
protocol.
The protocol divide into three sections:
• Set-Function
• Get-Function
• Remote control pass-through mode
※In below document, “PC” will represents all the control units that can sent or receive the
RS232 protocol command.
2. Description
2.1 Hardware specification
Viewsonic LCD communication port in the rear side
(1) Connector type: DSUB 9 Pin Male
(2) Pin Assignment
Male DSUB 9Pin
(outside view)
1 2 3 4 5
6 7 8 9
Pin #
1
2
3
4
5
6
7
8
9
frame
Signal
NC
RXD
TXD
NC
GND
NC
NC
NC
NC
GND
Remark
Input to LCD Monitor
Output from LCD Monitor
* Use of crossover (null modem) cable required for use
with PC.
2.2 Communication Setting
• Baud Rate Select: 9600bps (fixed)
• Data bits: 8bits (fixed)
• Parity: None (fixed)
• Stop Bits: 1 (fixed)
2.3 Command Message Reference
PC sends to Monitor command packet followed by “CR”. Every time PC sends control command to
the Monitor, the Monitor shall response as follows:
1. If the message is receives correctly it will send “+” (02Bh) followed by “CR” (00Dh)
2. If the message is receives incorrectly it will send “-” (02Dh) followed by “CR” (00Dh)
ViewSonic
37
VT3205LED
ENGLISH
1. Introduction
Other Information
ENGLISH
3. Command Description
Length
Total Byte of Message excluding “CR”
TV ID
Identification for each of TV
Command Type
Identify command type,
“s” (0x73h) : Set Command
“g” (0x67h) : Get Command
“r” (0x72h) : Reply Command
“p” (0x70h) : RCU Pass-through
“+” (0x2Bh) : Valid command Reply
“-” (0x2Dh) : Invalid command Reply
Command
Function command code: One byte ASCII code
Value[1~3]
Three bytes ASCII that defines the value
CR
0x0D
4. Set-Function Listing
The PC can control the LCD Monitor for specific actions. The Set-Function command allows
you to control the LCD monitor behavior in a remote sit through the RS232 port. The SetFunction packet format consists of 11 bytes.
Set-Function description:
Length
Total Byte of Message excluding “CR”
TV ID
Identification for each of TV. The TV ID doesn’t be supported by HDTV “power
on” command.
If we want to set all TV settings, TV ID can use “99” to achieve, and it will not
have Reply command on this function.
Command Type
Identify command type,
“s” (0x73h) : Set Command
Command
Function command code: One byte ASCII code
Value[1~3]
Three bytes ASCII that defines the value
CR
0x0D
Set-Function format:
Send (Command Type= “s”)
Name
Length
ID
Command Command
Type
Byte Count
1 Byte
2 Byte
1 Byte
Bytes order
1
2~3
4
Value1
Value2
Value3
CR
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
5
6
7
8
9
Value1
Value2
Value3
CR
(Command Type= “s”, Only for HDTV power on)
Name
Length
Byte Count
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
Bytes order
1
2
3
4
5
6
7
ViewSonic
Command Command
Type
38
VT3205LED
Other Information
Name
Length
ID
Command
Type
CR
Byte Count
1 Byte
2 Byte
1 Byte
1 Byte
Bytes order
1
2~3
4
5
ENGLISH
Reply (Command Type= “+” or “-”)
(Command Type= “+” or “-”, Only for HDTV power on)
Name
Length
Command
Type
CR
Byte Count
1 Byte
1 Byte
1 Byte
Bytes order
1
2
3
Example1: Set HDTV power on and this command is valid.
Send (Hex Format)
Name
Hex
Length
0x36
Command Command
Type
0x73
0x21
Length
Command
Type
CR
0x32
0x2B
0x0D
Value1
Value2
Value3
CR
0x30
0x30
0x31
0x0D
Reply (Hex Format)
Name
Hex
Example2: Set Brightness as 76 for TV-02 and this command is valid.
Send (Hex Format)
Name
Hex
Length
ID
Command Command
Type
0x38
0x30
0x32
0x73
0x24
Length
ID
Command
Type
CR
0x34
0x30
0x32
0x2B
0x0D
Value1
Value2
Value3
CR
0x30
0x37
0x36
0x0D
Reply (Hex Format)
Name
Hex
ViewSonic
39
VT3205LED
Other Information
Example3: Set Brightness as 76 for TV-02 and this command is NOT valid.
Send (Hex Format)
ENGLISH
Name
Hex
Length
ID
Command Command
Type
0x38
0x30
0x32
0x73
0x24
Length
ID
Command
Type
CR
0x34
0x30
0x32
0x2D
0x0D
Value1
Value2
Value3
CR
0x30
0x37
0x36
0x0D
Reply (Hex Format)
Name
Hex
Example4: Set Tint as -32 for TV-03 and this command is valid.
Send (Hex Format)
Name
Hex
Length
ID
Command Command
Type
0x38
0x30
0x33
0x73
0x27
Length
ID
Command
Type
CR
0x34
0x30
0x33
0x2B
0x0D
Value1
Value2
Value3
CR
0x2D
0x33
0x32
0x0D
Reply (Hex Format)
Name
Hex
Example5: Set Tint as -75 for TV-03 and this command is NOT valid.
Send (Hex Format)
Name
Hex
Length
ID
Command Command
Type
0x38
0x30
0x33
0x73
0x27
Length
ID
Command
Type
CR
0x34
0x30
0x33
0x2B
0x0D
Value1
Value2
Value3
CR
0x2D
0x37
0x35
0x0D
Reply (Hex Format)
Name
Hex
Example6: Set Brightness as 76 for all TV and this command is valid.
Send (Hex Format)
Name
Hex
Length
ID
0x38
0x39
0x39
Command Command
Type
0x73
0x24
Value1
Value2
Value3
CR
0x30
0x37
0x36
0x0D
No Reply..
ViewSonic
40
VT3205LED
Other Information
Table 4-1: PC Set-function command to LCD Monitor (ID=C0h)
HDTV Power
Input Select
Contrast
Brightness
Sharpness
Color
Tint
Color Mode
Surround
Bass
Treble
Balance
OSD Language
Power Lock
Volume
Mute
Button Lock
TV Channel
Menu Lock
Number
Key Pad
Command
Command
Value Range
Code (ASCII) Code (Hex) (Three ASCII bytes)
!
21
000: STBY
001: ON
`
22
000: TV
001: AV
002: SV
003: YPBPR
004: HDMI 1
005: HDMI 2
006: VGA
#
23
000 ~ 100
$
24
000 ~ 100
%
25
000 ~ 100
&
26
000 ~ 100
`
27
-50 ~ +50
)
29
000: NORMAL
001: WARM
002: COLD
2D
000: OFF
001: ON
.
2E
000 ~ 100
/
2F
000 ~ 100
0
30
000 ~ 100
2
32
000: English
001: Francias
002: Spanish
4
34
000: Unlock
001: Lock
5
35
000 ~ 100
6
36
000: OFF
001: ON (mute)
8
38
000 : Unlock
001 : Lock
=
3D
000 ~ 999
>
3E
000: Unlock
001: Lock
@
40
000 ~ 009
A
41
000: UP
001: DOWN
002: LEFT
003: RIGHT
004: ENTER
005: INPUT
006: MENU/EXIT
Remote Control
B
42
Restore To Default
~
7E
ViewSonic
Comments
Controlled the HDTV power status: ON or
Standby
Sets Bass value
Sets Treble value
Sets Balance position
Disable: RCU has no effect on HDTV.
Enabled: RCU controls the HDTV. This
000: DISABLE
is the power up default on the HDTV.Pass
001: ENABLE
through: RCU has no effect on HDTV and
002: PASS THROUGH all RCU command codes are transmitted to
FC via the RS232 port. See page 51 for more
details
000
Rests HDTV to factory setting
41
VT3205LED
ENGLISH
Set Function
Other Information
ENGLISH
5. Get-Function Listing
The PC can interrogate the LCD Monitor for specific information. The Get-Function packet
format consists of 5 bytes which is similar to the Set-Function packet structure. Note that the
“Value” byte is always = 00.
Get-Function description:
Length
Total Byte of Message excluding “CR”
TV ID
Identification for each of TV. The TV ID doesn’t be supported by HDTV power
status on standby.
Command Type
Identify command type,
“g” (0x67h) : Get Command
Command
Function command code: One byte ASCII code
Value[1~3]
Three bytes ASCII that defines the value
CR
0x0D
Get-Function format:
Send (Command Type= “g”)
Name
Length
ID
Byte Count
1 Byte
2 Byte
1 Byte
Bytes order
1
2~3
4
Command Command
Type
Value1
Value2
Value3
CR
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
5
6
7
8
9
(Command Type= “g”, Only for HDTV power status on standby)
Name
Length
Byte Count
1 Byte
1 Byte
Bytes order
1
2
Command Command
Type
Value1
Value2
Value3
CR
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
3
4
5
6
7
Value1
Value2
Value3
CR
Reply: (Command Type= “r” or “-”)
If the Command is valid, Command Type = “r”
Name
Length
ID
Command Command
Type
Byte Count
1 Byte
2 Byte
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
Bytes order
1
2~3
4
5
6
7
8
9
If the Command is valid, Command Type = “r”, Only for HDTV power status on standby.
Name
Length
Command Command
Type
Byte Count
1 Byte
1 Byte
Bytes order
1
2
Value1
Value2
Value3
CR
1 Byte
1 Byte
1 Byte
1 Byte
1 Byte
3
4
5
6
7
If the Command is Not valid, Command Type= “-”
Name
Length
ID
Command
Type
CR
Byte Count
1 Byte
2 Byte
1 Byte
1 Byte
Bytes order
1
2~3
4
5
ViewSonic
42
VT3205LED
Other Information
Name
Length
Command
Type
CR
Byte Count
1 Byte
1 Byte
1 Byte
Bytes order
1
2
3
ENGLISH
If the Command is Not valid, Command Type= “-”, Only for HDTV power status on
standby.
Example1: Get power status on standby and this command is valid.
Send (Hex Format)
Name
Hex
Length
0x36
Command Command
Type
0x67
0x6C
Value1
Value2
Value3
CR
0x30
0x30
0x30
0x0D
Value1
Value2
Value3
CR
0x30
0x30
0x30
0x0D
Reply (Hex Format)
Name
Hex
Length
0x36
Command Command
Type
0x72
0x6C
Example2: Get Brightness from TV-05 and this command is valid.
The Brightness value is 67.
Send (Hex Format)
Name
Hex
Length
ID
0x38
0x30
0x35
Command Command
Type
0x67
0x62
Value1
Value2
Value3
CR
0x30
0x30
0x30
0x0D
Value1
Value2
Value3
CR
0x30
0x36
0x37
0x0D
Reply (Hex Format)
Name
Hex
Length
ID
0x38
0x30
0x35
Command Command
Type
0x72
0x62
Example3: Get Brightness from TV-05 , but the Brightness command ID is error
and it is NOT in the command table.
Send (Hex Format)
Name
Hex
Length
ID
Command Command
Type
0x38
0x30
0x35
0x67
0xD3
Length
ID
Command
Type
CR
0x34
0x30
0x35
0x2D
0x0D
Value1
Value2
Value3
CR
0x30
0x30
0x30
0x0D
Reply (Hex Format)
Name
Hex
ViewSonic
43
VT3205LED
Other Information
ENGLISH
Example4: Get Tint from TV-0007 and this command is valid.
The Tint value is +32.
Send (Hex Format)
Name
Hex
Length
ID
0x38
0x30
0x37
Command Command
Type
0x67
0x65
Value1
Value2
Value3
CR
0x30
0x30
0x30
0x0D
Value1
Value2
Value3
CR
0x2B
0x33
0x32
0x0D
Reply (Hex Format)
Name
Hex
Length
ID
0x38
0x30
0x37
Command Command
Type
0x72
0x65
Example5: Get Tint from TV-07 , but the Brightness command ID is error and it is
NOT in the command table.
Send (Hex Format)
Name
Hex
Length
ID
Command Command
Type
0x38
0x30
0x37
0x67
0xD7
Length
ID
Command
Type
CR
0x34
0x30
0x37
0x2D
0x0D
Value1
Value2
Value3
CR
0x30
0x30
0x30
0x0D
Reply (Hex Format)
Name
Hex
ViewSonic
44
VT3205LED
Other Information
§ Table 5-1 outlines the Get-function command list that must be supported by the LCD
Monitor.
Get Function
Command
Code
(ASCII)
Get-Contrast
a
Get-Brightness
Get-Sharpness
Command
Response Range
Code
(Three ASCII bytes)
(Hex)
ENGLISH
Table 5-1: PC Get-function command to LCD Monitor
Comments
61
000 ~ 100
Gets Contrast value
b
62
000 ~ 100
Gets Brightness value
c
63
000 ~ 100
Gets Sharpness value
Get-Color
d
64
000 ~ 100
Gets Color value
Get-Tint
e
65
-50 ~ +50
Gets Tint value
Get-Volume
f
66
000 ~ 100
Gets Volume value
Get-Mute
g
67
000: OFF (unmuted)
001: ON (muted)
Gets Mute ON/OFF status
Get-Input select
j
6A
000: TV
001: AV
002: SV
003: YPBPR
004: HDMI 1
005: HDMI 2
006: VGA
Gets Input select status
Get-Power status
l
6C
000: STBY
001: ON
Gets the status of the HDTV power.
HDTV response:
000 = HDTV is in standby
001 = HDTV is ON
000: DISABLE
001: ENABLE
002: PASS
THROUGH
Get-Remote
Control
n
6E
Get-Power Lock
o
6F
000: Unlock
001: Lock
Get-Button Lock
p
70
000: Unlock
001: Lock
Get-Menu Lock
q
71
000: Unlock
001: Lock
Get-ACK
z
7A
000
ViewSonic
Disable: RCU has no effect on HDTV.
Enabled: RCU controls the HDTV. This
is the power up default on the HDTV.
Pass through: RCU has no effect on
HDTV and all RCU command codes are
transmitted to FC via the RS232 port. See
page 51 for more details
This command is used to test the
communication link.
45
VT3205LED
Other Information
ENGLISH
6. Remote Control Pass-through mode
When PC sets the LCD monitor to Remote Control Pass through mode, the LCD shall send a
three bytes packet (followed by “CR”) in response to RCU button activation. Note, that in this
mode the RCU shall have no effect on the monitor function. For example: “+Volume” will not
change the volume in the LCD but only sends “+Volume” code to PC over the RS232 port.
RCU Pass-through Command description:
Length
Total Byte of Message excluding “CR”
TV ID
Identification for each of TV
Command Type
Identify command type,
“p” (0x70h) : RCU Pass-through
Value[1~2]
Two bytes ASCII that defines the value
CR
0x0D
RCU Pass-through Command Format:
Reply: (Command Type= “p”)
Name
Length
ID
Command
Type
Value1
Value2
CR
Byte Count
1 Byte
2 Byte
1 Byte
1 Byte
1 Byte
1 Byte
Bytes order
1
2~3
4
5
6
7
Example1: User press “Menu” Key form RCU to TV-03 and RCU data pass-through
to Server, then server will receive “1A”.
Reply (Hex Format)
Name
Hex
Length
ID
Command
Type
Value1
Value2
CR
0x36
0x30
0x33
0x70
0x31
0x41
0x0D
Example2: User press “5” Key form RCU to TV-07 and RCU data pass-through to Server,
then server will receive “05”.
Reply (Hex Format)
Name
Hex
ViewSonic
Length
ID
Command
Type
Value1
Value2
CR
0x36
0x30
0x36
0x70
0x30
0x35
0x0D
46
VT3205LED
Other Information
Table 6-1: Baseline RCU Pass-through codes
Code (HEX)
RECALL
ZOOM
VOLUME UP (+) VOLUME DOWN (-) MUTE
CHANNEL/PAGE UP (+) CHANNEL/PAGE DOWN (-)
▲
▼
▲
▼
SOURCES (INPUTS)
SLEEP
MENU
UP
DOWN
LEFT
RIGHT
OK (ENTER)
ViewSonic
▲
▼
◄
►
Key
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
Code (HEX)
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
47
ENGLISH
Key
1
2
3
4
5
6
7
8
9
0
VT3205LED
Other Information
Customer Support
ENGLISH
For technical support or product service, see the table below or contact your reseller.
Note: You will need the product serial number.
Use with other Wall-Mount kit may cause instability and possibly result in injury.
To find the perfect mount for VT3205LED, please browse www.viewsonic.com or call
our service team: United States 1-800-688-6688, Canada 1-866-463-4775.
Country/Region
Website
T = Telephone
F = FAX
Email
United States
www.viewsonic.com
T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530
F= 1-909-468-3757
service.us@viewsonic.com
Canada
www.viewsonic.com
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-3757
service.ca@viewsonic.com
Latin America
(Argentina)
www.viewsonic.com/la/
T= 0800-4441185
soporte@viewsonic.com
Latin America (Chile)
www.viewsonic.com/la/
T= 1230-020-7975
soporte@viewsonic.com
Latin America
(Columbia)
www.viewsonic.com/la/
T= 01800-9-157235
soporte@viewsonic.com
Latin America (Mexico)
www.viewsonic.com/la/
T= 001-8882328722
soporte@viewsonic.com
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru)
ViewSonic
www.viewsonic.com/la/
T= 0800-54565
48
soporte@viewsonic.com
VT3205LED
Other Information
Limited Warranty
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period.
If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or
replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How long the warranty is effective:
ViewSonic LED TVs are warranted for 3 years for all parts excluding the light source and 3 years for labor from the date of the first customer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by ViewSonic.
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electric power fluctuations or failure.
f. Use of supplies or parts not meeting ViewSonic’s specifications.
g. Normal wear and tear.
h. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the
product for an extended period of time.
4. Removal, installation, and set-up service charges.
5. When you mount it on the wall, the following must be noticed:
a. The accessories attached with this product are applicable for this product only.
b. When the product is mounted on the wall, holes and fixed screws will remain in the wall body.
c. Wall face may discolor when this product has been mounted on the wall for a long time.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to Customer Support
page). You will need to provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a
description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of
merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss
of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial
loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow
limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and
exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic or your local ViewSonic
dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject to the terms and conditions of the
Maintenance Guarantee Card.
For users in Europe and Russia, full details of warranty providedcan be found in www.viewsoniceurope.com under Support/Warranty Information.
4.3: ViewSonic LED TV Warranty LTV_LW01 Rev. 1C 06-25-07
ViewSonic
49
VT3205LED
ENGLISH
VIEWSONIC LED TV
Other Information
Mexico Limited Warranty
ENGLISH
VIEWSONIC LED TV
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the
warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic
will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include
remanufactured or refurbished parts or components & accessories.
How long the warranty is effective:
ViewSonic LED TVs are warranted for 3 years for all parts excluding the light source and 3 years for labor from the
date of the first customer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a.Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification,
unauthorized attempted repair, or failure to follow instructions supplied with the product.
b.Any damage of the product due to shipment.
c.Causes external to the product, such as electrical power fluctuations or failure.
d.Use of supplies or parts not meeting ViewSonic’s specifications.
e.Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is
displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the
attached Customer Support page). You will need to provide your product’s serial number, so please record the product
information in the space provided below on your purchase for your future use. Please retain your receipt of proof of
purchase to support your warranty claim.
For Your Records
Product Name: ____________________________
Model Number: _______________________________
Document Number: ________________________
Serial Number: ________________________________
Purchase Date: ____________________________
Extended Warranty Purchase? ________________(Y/N)
If so, what date does warranty expire? ______________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your
address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the
implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of
the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business
relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
ViewSonic
50
VT3205LED
Other Information
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099
http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av.
Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Fax: 1-800-685-7276
E-Mail: http://www.viewsonic.com
4.3: ViewSonic Mexico Limited Warranty LTV_LW02 Rev. 1A 06-25-07
ViewSonic
51
VT3205LED
ENGLISH
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
2001132333P
ViewSonic
TM