Back to Basics SCL5 Specifications

Allen-Bradley DF1
Driver Help
© 2014 Kepware Technologies
Allen-Bradley DF1 Driver Help
2
Table of Contents
Table of Contents
2
Allen-Bradley DF1 Driver Help
5
Overview
5
Channel Setup
6
Link Settings
6
Full Duplex
7
Half Duplex Master
7
KF2/KF3 Half Duplex Master
8
Radio Modem
9
Device Setup
10
Modem Setup
10
Protocol Settings
10
Cable Connections
11
SLC500 Connection
12
15-Pin Module Connection
12
25-Pin Module Connection
12
13
Function File Options
Function File Block Writes
13
SLC500 Slot Configuration
14
SLC 500 Modular I/O Selection Guide
14
Communicating with RSLogix5000 Family Controllers
16
Data Types Description
20
Address Descriptions
21
Micrologix Addressing
21
SLC500 Addressing (Fixed I/O processor)
21
SLC5/01 Addressing
21
SLC5/02 Addressing
22
SLC5/03 Addressing
22
SLC5/04 Addressing
22
SLC5/05 Addressing
22
22
PLC5 Addressing
Output Files
23
Input Files
26
Status Files
28
Binary Files
29
Timer Files
30
Counter Files
30
Control Files
31
www. kepware.com
Allen-Bradley DF1 Driver Help
3
Integer Files
31
Float Files
32
ASCII Files
32
String Files
33
BCD Files
33
Long Files
34
Micrologix PID Files
34
PLC5 PID Files
35
Micrologix Message Files
36
PLC5 Message Files
37
Block Transfer Files
38
High Speed Counter File (HSC)
38
Real-Time Clock File (RTC)
39
Channel 0 Communication Status File (CS0)
40
Channel 1 Communication Status File (CS1)
40
I/O Module Status File (IOS)
41
Error Descriptions
42
42
Address Validation
Missing address
43
Device address '<address>' contains a syntax error
43
Address '<address>' is out of range for the specified device or register
43
Device address '<address>' is not supported by model '<model name>'
43
Data Type '<type>' is not valid for device address '<address>'
43
Device address '<address>' is Read Only
44
Array size is out of range for address '<address>'
44
Array support is not available for the specified address: '<address>'
44
44
Serial Communications
COMn does not exist
44
Error opening COMn
44
COMn is in use by another application
45
Unable to set comm parameters on COMn
45
Communications error on '<channel name>' [<error mask>]
45
45
Device Status Messages
Device '<device name>' is not responding
45
Unable to write to '<address>' on device '<device name>'
46
46
Device Specific Messages
Unable to read data starting at <start address> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]
47
Unable to read data starting at <start address> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]. Block deactivated
47
www. kepware.com
Allen-Bradley DF1 Driver Help
4
Unable to read function file <fun. file element> on device '<device name>' [Status=<STS>, Ext. Status=<
EXT. STS>]
47
Unable to read function file <fun. file element> on device '<device name>' [Status=<STS>, Ext. Status=<
EXT. STS>]. Block deactivated
48
Unable to read data starting at <start address> on device '<device name>'. Framing error
48
Unable to read function file <fun. file element> on device '<device name>'. Framing error
48
Unable to read data starting at <start address> on device '<device name>'. checksum error
48
Unable to read function file <fun. file element> on device '<device name>'. Checksum error
48
Unable to read data starting at <start address> on device '<device name>'. Slave sink/source full
49
Unable to read function file <fun. file element> on device '<device name>'. Slave sink/source full
49
Unable to read data starting at <start address> on device '<device name>'. Slave source empty
49
Unable to read function file <fun. file element> on device '<device name>'. Slave source empty
49
Error writing to address '<address>' on device '<device name>' [Status=<STS>, Ext. Status=<EXT. STS>]
50
Error writing to address '<address>' on device '<device name>'. Framing error
50
Checksum error occurred writing to address '<address>' on device '<device name>'
50
Error writing to address '<address>' on device '<device name>'. Slave sink/source full
50
Error writing to address '<address>' on device '<device name>'. Slave source empty
51
Device '<device name>' timed out writing to address '<address>'
51
Unable to read data starting at <start address> on device '<device name>'. Device replied with a NAK
51
Unable to read function file <fun. file element> on device '<device name>'. Device replied with a NAK
51
Unable to read data starting at <start address> on device '<device name>'. Memory map error
51
Unable to read function file <fun. file element> on device '<device name>'. Memory map error
52
Unable to read data starting at '<start address>' on device '<device name>'. Device replied with an
unexpected NAK. Check device link protocol
52
Unable to read function file '<fun. file element>' on device '<device name>'. Device replied with an
unexpected NAK. Check device link protocol
52
Index
53
www. kepware.com
Allen-Bradley DF1 Driver Help
5
Allen-Bradley DF1 Driver Help
Help version 1.033
CONTENTS
Overview
What is the Allen-Bradley DF1 Driver?
Channel Setup
How do I configure a channel for use with this driver?
Device Setup
How do I configure a device for use with this driver?
Data Types Description
What data types are supported by this driver?
Address Descriptions
How do I address a data location on an Allen-Bradley DF1 device?
Error Descriptions
What error messages are produced by the Allen-Bradley DF1 Driver?
Overview
The Allen-Bradley DF1 Driver provides an easy and reliable way to connect Allen-Bradley DF1 devices to OPC
Client applications, including HMI, SCADA, Historian, MES, ERP and countless custom applications. This driver
supports Allen-Bradley Micrologix, SLC500, and PLC5 series PLCs.
www. kepware.com
Allen-Bradley DF1 Driver Help
6
Channel Setup
Supported Link Protocols
Allen-Bradley DF1 Full-Duplex (point-to-point communication)
Allen-Bradley DF1 Half-Duplex Master (multi-drop communication) also known as Allen-Bradley DF1 PolledMode.*
Allen-Bradley DF1 Radio Modem (point-to-point and multi-drop communication).**
*Slave-to-slave communication is not supported.
**Store and forward feature is not supported.
Note: For required firmware versions for Allen-Bradley DF1 Radio Modem support, refer to Device Setup.
Supported Communication Parameters*
Baud Rate: 300, 600, 1200, 2400, 9600, 19200
Parity: None, Even, or Odd
Data Bits: 5, 6, 7 or 8
Stop Bits: 1 or 2
*Not all devices may support all listed configurations.
Note: Error Checking should be set to CRC or BCC within the device.
See Also: Link Settings
Link Settings
To access the Link Settings dialog after the Channel Wizard has closed, left-click on the channel and select
Properties. Then, select the Link Settings tab.
Station Number
The Station Number should be set based on the device being communicated with (excluding radio modems). The
following should be taken into account:
l
If the destination device is on a DH+ or DH-485 network, communication must go through a Serial-toDH+/DH-485 converter (i.e. KF2/KF3 module). In this case, the device being communicated with is the
converter, not the destination device itself (which is a Micrologix, SLC500, or PLC-5). The station number
for this configuration should be set to the converter's node address.
www. kepware.com
Allen-Bradley DF1 Driver Help
7
l
If the destination device is not on a DH+ or DH-485 network, the device being communicated with is a
Micrologix, SLC500, or PLC-5 PLC. The station number for this configuration can be set to an arbitrary
unique address.
Standard Serial Configuration
Station Number = Arbitrary unique address on the network for the local PC. The range for DH-485 is 1 to 63.
Otherwise, the range is 0 to 255.
DH+/DH-485 Converter Configuration
Station Number = Converter's node address (e.g. KF2/KF3 node address).
Link Protocol
The Allen-Bradley DF1 Driver implements the following link protocols:
Standard Serial Configuration
Full-Duplex (a.k.a Allen-Bradley DF1 )
Half-Duplex Master (a.k.a Polled-Mode)
KF2/KF3 Half-Duplex Master
Radio Modem
DH+/DH-485 Converter Configuration
Full-Duplex (a.k.a Allen-Bradley DF1 )
KF2/KF3 Half-Duplex Master
Slave Re-Poll Delay (ms)
For more information, refer to Slave Re-Poll Delay.
Only accept responses for Station Num
For more information, refer to Full-Duplex.
Full Duplex
Full-duplex protocol is used over a point-to-point link, allowing for high performance two-way communications
between peers.
Only accept responses for Station Num:
When checked, this parameter limits the acceptance of responses to those that are destined for the station as
indicated by the Station Num field.
Half Duplex Master
Half-Duplex Protocol is a multi-drop protocol with one master and one or more slaves. Generally, Half-Duplex
provides lower data throughput than Full Duplex, but it adds the flexibility of being able to communicate with
multiple devices from a single COM port. Half-Duplex is a master/slave protocol. In Half-Duplex Master mode, the
driver is the master and all devices on the network are slaves. It is necessary that all the devices on the network
be configured as Half-Duplex Slave since only one master is allowed on the network. For more information on
configuring the Micrologix/SLC500/PLC5 device using RSLogix, refer to the Rockwell documentation.
Note: If the destination device is on a DH-485 or DH+ network, communication must go through a KF2/KF3
module respectively. If the KF2/KF3 module is configured as a Half-Duplex Slave, the KF2/KF3 Half-Duplex
Master Link Protocol must be chosen.
Master Responsibilities and Update Rates
The driver (master) is responsible for polling the slaves for data. In general, slaves would be polled in a roundrobin manner. Due to the nature of OPC, how often a slave gets polled depends on the slave tags' update rate. In
this manner, slaves are only polled when a Read/Write operation is requested from them. This reduces the traffic
on the network and prevents unnecessary requests from taking place. In essence, the design of the client project
(specifically update rates assigned) determines the traffic on the network. The faster the update rate, the more
often a slave will be polled.
Messages, Sink and Source
There are three messages exchanged between master and slave in a Read/Write operation. The first is the master
message requesting the slave to perform a Read/Write operation. The slave does not respond immediately with
data as in full-duplex mode. The second message is a poll message from the master to the slave requesting the
data gathered from the last master message operation. The third is the slave response with the data requested in
www. kepware.com
Allen-Bradley DF1 Driver Help
8
the master message. Incoming requests to the slave are placed in what is termed a "sink". Once the slave
performs the operation requested, it places the result in what is termed a "source".
Number of Attempts
The number of attempts for master messages and polls share the same number of attempts as configured in the
device Fail after xxx successive timeouts. This attempt count is misleading in Half-Duplex mode since there
are multiple messages sent from the master in a single data request. For all intents and purposes:
Let cnAttempts = xxx in Fail after xxx successive timeouts
# attempts for master message timeout = cnAttempts
# attempts for poll timeout = cnAttempts
# attempts for request timeout = # attempts for master message timeout + # attempts for poll timeout ==
cnAttempts X 2
Source Empty and Slave Re-Poll Delay
The Allen-Bradley DF1 driver is optimized to send master messages and polls as quickly as possible to increase
data throughput. The initial slave poll will not be delayed since a delay is unnecessary. If the slave needs time to
process requests in its sink, it will be apparent in the initial poll response. It is at this time in which the driver
introduces a delay and re-polls the slave. Such a delay allows the slave time to process the request before the
next poll. This delay is set with the Slave Re-Poll Delay field. The slave will be re-polled cnAttempts times.
Sink and Source Full
Both sink and source are essentially buffers and buffers have limitations. More importantly, it is possible for the
sink to fill up with requests. If this occurs, the slave will not acknowledge any master messages it receives. If
after cnAttempts the slave does not ACK the master, it is most likely the case that the slave sink is full. The driver
will then poll the slave emptying any responses the slave may have, making room for responses of the requests
that were in the full sink. This polling action will take place until the slave source is empty after cnAttempts. On
the next slave request, it is likely that the sink will be empty. If it is not, it may mean the driver is polling the slave
too quickly. If this is the case, increase the Slave Re-Poll Delay. Likewise, the slave source may also become full
and the driver will again poll the slave until the source is empty after cnAttempts.
Accepted and Discarded Slave Reponses
In the above sections, it has been mentioned that the slave is polled until the emptied. This is possible if the slave
source is full of queued up responses. On any given poll, only the response to the last master message is
accepted, all others are discarded.
Note: Slave-to-slave communication is not supported.
KF2/KF3 Half Duplex Master
Half-Duplex Protocol is a multi-drop protocol with one master and one or more slaves. Generally, Half-Duplex
provides lower data throughput than Full Duplex, but it adds the flexibility of being able to communicate with
multiple KF2/KF3 modules from a single COM port. Half-Duplex is a master/slave protocol. In Half-Duplex Master
mode, the driver is the master and all KF2/KF3 modules on the network are slaves. It is necessary that all the
devices on the network be configured as Half-Duplex Slave since only one master is allowed on the network. For
more information on configuring the KF2/KF3 module for Half-Duplex slave operation, refer to the Rockwell
documentation.
Master Responsibilities and Update Rates
The driver (master) is responsible for polling the slaves for data. In general, slaves would be polled in a roundrobin manner. Due to the nature of OPC, how often a slave gets polled depends on the update rate of the slave’s
tags. In this manner, slaves are only polled when a Read/Write operation is requested from them. This reduces
the traffic on the network and prevents unnecessary requests from taking place. In essence, the design of the
client project (specifically update rates assigned) determines the traffic on the network. The faster the update
rate, the more often a slave will be polled.
Messages, Sink and Source
There are three messages exchanged between master and slave in a Read/Write operation. The first is the master
message requesting the slave to perform a Read/Write operation. The slave does not respond immediately with
data as in full-duplex mode. The second message is a poll message from the master to the slave requesting the
data gathered from the last master message operation. The third is the slave response with the data requested in
the master message. Incoming requests to the slave are placed in what is termed a "sink". Once the slave
performs the operation requested, it places the result in what is termed a "source".
Number of Attempts
www. kepware.com
Allen-Bradley DF1 Driver Help
9
The number of attempts for master messages and polls share the same number of attempts as configured in the
device Fail after xxx successive timeouts. This attempt count is misleading in Half-Duplex mode since there
are multiple messages sent from the master in a single data request. For all intents and purposes:
Let cnAttempts = xxx in Fail after xxx successive timeouts
# attempts for master message timeout = cnAttempts
# attempts for poll timeout = cnAttempts
# attempts for request timeout = # attempts for master message timeout + # attempts for poll timeout ==
cnAttempts X 2
Source Empty and Slave Re-Poll Delay
The Allen-Bradley DF1 driver is optimized to send master messages and polls as quickly as possible to increase
data throughput. The initial slave poll will not be delayed since a delay is unnecessary. If the slave needs time to
process requests in its sink, it will be apparent in the initial poll response. It is at this time in which the driver
introduces a delay and re-polls the slave. Such a delay allows the slave time to process the request before the
next poll. This delay is configured in Channel Properties (under the Protocol tab) and is called Slave Re-Poll
Delay. The slave will be re-polled cnAttempts times.
Sink and Source Full
Both sink and source are essentially buffers and buffers have limitations. More importantly, it is possible for the
sink to fill up with requests. If this occurs, the slave will not acknowledge any master messages it receives. If
after cnAttempts the slave does not ACK the master, it is most likely the case that the slave sink is full. The driver
will then poll the slave emptying any responses the slave may have, making room for responses of the requests
that were in the full sink. This polling action will take place until the slave source is empty after cnAttempts. On
the next slave request, it is likely that the sink will be empty. If it is not, it may mean the driver is polling the slave
too quickly. If this is the case, increase the Slave Re-Poll Delay. Likewise, the slave source may also become full
and the driver will again poll the slave until the source is empty after cnAttempts.
Accepted and Discarded Slave Reponses
In the above sections, it has been mentioned that the slave is polled until the emptied. This is possible if the slave
source is full of queued up responses. On any given poll, only the response to the last master message is
accepted: all others are discarded.
Note: Slave-to-slave communication is not supported.
Radio Modem
The Radio Modem protocol is a command/reply protocol. There are no ACKs or NAKs during the request/response
procedure. This reduces the number of bytes the radio modems have to transmit and receive in order to complete
a transaction. This protocol supports full-duplex communications over a point-to-point link allowing for high
performance two-way communications between peers. It also supports master/slave communications allowing
for multi-drop configurations. Performance exceeds both Full-Duplex and Half-Duplex Protocols.
www. kepware.com
Allen-Bradley DF1 Driver Help
10
Device Setup
Supported Devices
Micrologix Series*
SLC500 Series*
PLC-5 Series (excluding the PLC-5/250 and PLC-5/VME series)
RSLogix5000
*Radio Modem link protocol requires the following firmware upgrades:
SLC 5/03, SLC 5/04 and SLC 5/05: Series C FRN6
MicroLogix 1200: Series C FRN7
MicroLogix 1500: Series C FRN8
Device ID
The Device ID is the Allen-Bradley DF1 network address of the PLC. For PLCs on a DH-485 or DH+ network, the
range is 1-63. Otherwise, the range is 0-255.
For Full Duplex, the default address of 1 will work.
For Half-Duplex, the address must match the slave address.
For Radio Modem, the address must match the slave/peer address.
Ethernet Encapsulation
This driver supports Ethernet Encapsulation, which allows the driver to communicate with serial devices
attached to an Ethernet network using a terminal server. Ethernet Encapsulation mode may be invoked through
the COM ID dialog in Channel Properties. For more information, refer to the OPC Server's help documentation.
DH-485 and DH+ Support
An Allen Bradley KF3 or compatible device is needed to connect the driver to the DH-485 network. There are four
options for communicating to a device on DH+ using the Allen-Bradley DF1 Device Driver.
l
Allen Bradley KF2 or compatible device.
l
1784-U2DHP USB converter. This converter appears as a new serial port to the system.
l
DataLink DL Interface Cards (PCI/ISA/PC104). These cards add virtual serial ports for seamless
configuration.
l
DataLink DL4500 Ethernet-to-DH+ Converter. Configure the device for Ethernet Encapsulation. NIC is
required.
See Also:
Cable Connections
Function File Options
SLC500 Slot Configuration
Communicating with RSLogix5000 Family Controllers
Modem Setup
This driver supports modem functionality. For more information, please refer to the topic "Modem Support" in the
OPC Server Help documentation.
Protocol Settings
Error Checking Method
There are two methods of error checking available in the Allen-Bradley DF1 driver: Block Check Character (BCC)
and 16 bit Cyclic Redundancy Check (CRC-16). Users must choose the checksum method expected by the device;
otherwise, the device will not respond.
Request Size
This parameter is used to change the size of a data request. It can be important in refining the application's
performance. If the application accesses large areas of PLC memory consecutively, then a large request size may
be beneficial. If the data is spread throughout the PLC, then a small request size may be beneficial. The default
setting is the large request size.
Swap PLC-5 Float Words?
PLC-5 Floats follow the IEEE 754 standard. They contain a sign bit S, an exponent E and a mantissa M. The 32 bit
layout of this IEEE 754 Float is as shown below.
www. kepware.com
Allen-Bradley DF1 Driver Help
11
Upper Word Lower Word
SEEEEEEE EMMMMMMM MMMMMMMM MMMMMMMM
Byte 3 Byte 2 Byte 1 Byte 0
Allen-Bradley PLC-5 devices transfer binary Floating-point data on the serial link in the following order:
Upper Word Lower Word
Byte 2 Byte 3 Byte 0 Byte 1
This means the upper word is received first, followed by the lower word. Due to this ordering, a swap of the
words is required, providing:
Lower Word Upper Word
Byte 0 Byte 1 Byte 2 Byte 3
The result passed on to the client is as follows:
Byte 3 Byte 2 Byte 1 Byte 0
Some PLC-5 emulated devices (such as the Avtron ADDvantage-32) already transfer binary Floating point data on
the serial link with the lower word first.
Lower Word Upper Word
Byte 0 Byte 1 Byte 2 Byte 3
In this case, no swap is required. The result passed on to the client is as follows:
Byte 3 Byte 2 Byte 1 Byte 0
Thus, the rule of thumb is if the device transfers the lower word first, then the upper word in the packet on the
serial link does not require word swapping. This only applies to PLC-5 emulated devices; that is, devices that use
the Allen-Bradley DF1 protocol with PLC-5 commands. Allen-Bradley PLC-5 devices always transfer the upper
word first followed by the lower word so the Float words must be swapped. This is the default setting.
Support Float Access to SLC/Micrologix N Files?
SLC and Micrologix users can select whether the driver will natively support Float access to Integer Files. The
default setting is Yes.
Cable Connections
This driver is an Allen-Bradley DF1 RS232 serial driver. It does not handle the token ring passing of a DH-485 or
DH+ network. When testing cable connections for this driver, first verify communications using the Allen Bradley
programming software.
l
For Micrologix and SLC 500 series PLCs, if the APS driver selected is KF3/KE, Full-Duplex, Half-Duplex
Slave or Full Duplex (Micro) and communication is available with the PLC, this driver will also be able to
communicate using the same cabling and communication settings.
l
For PLC5 series PLCs, if the PLC-5 programming software driver selected is Serial to PLC or KE/KF and
communication is available with the PLC, this driver will also be able to communicate using the same
cabling and communication settings.
Micrologix Series
Use the same cable as when using the Allen Bradley APS software.
SLC 500 Series - Direct connection
If the PLC has an RS232 port it can be connected directly using a standard RS232 null modem cable (which is the
same cable used in Allen Bradley APS software). The PLC port must be configured for Allen-Bradley DF1
communications, not DH-485 Master.
Note: This driver does not work in a direct connection to the DH-485 port of a SLC 500 series PLC using a 1747PIC converter the way the APS software does.
PLC5 Series - Direct connection
A direct connection can be made to the CH0 port of enhanced PLC5 processors using a standard RS232 null
modem cable. The port must be configured for Allen-Bradley DF1 communications.
DH-485 Networks
An Allen Bradley KF3 or compatible device is needed to connect the driver to the DH-485 network. A standard null
modem cable is used to connect the PC to the KF3 device.
DH+ Networks
There are three options for communicating to a device on DH+ using the Allen-Bradley DF1 Device Driver:
www. kepware.com
Allen-Bradley DF1 Driver Help
12
l
Allen Bradley KF2 or compatible device. A standard null modem cable is used to connect the PC to the KF2
device.
l
DataLink DL Interface Cards (PCI/ISA/PC104). Consult AB documentation for DH+ wiring.
l
DataLink DL4500 Ethernet-to-DH+ Converter. Consult DL4500 documentation for wiring.
SLC500 Connection
15-Pin Module Connection
25-Pin Module Connection
www. kepware.com
Allen-Bradley DF1 Driver Help
13
Function File Options
Function files are structure-based files, similar to PD and MG data files, and are unique to the Micrologix 1200
and 1500. For more information on a specific function file are supported in the Allen-Bradley DF1 Device Driver,
select a link from the list below.
High Speed Counter File (HSC)
Real-Time Clock File (RTC)
Channel 0 Communication Status File (CS0)
Channel 1 Communication Status File (CS1)
I/O Module Status File (IOS)
Function File Block Writes
For applicable function files, data can be written to the device in a single operation. By default, when data is
written to a function file sub element (field within the function file structure), a write operation occurs
immediately for that tag. For such files as the RTC file, whose sub elements include hour (HR), minute (MIN) and
second (SEC), individual writes are not always acceptable. With such sub elements relying solely on time, values
must be written in one operation to avoid time elapsing between sub elements writes. For this reason, there is the
option to "block write" these sub elements.
Applicable Function Files/Sub Elements
RTC
Year
YR
Month
MON
Day
DAY
Day of Week
DOW
Hour
HR
Minute
MIN
Second
SEC
How Block Writes Work
Block writing involves writing to the device the values of every Read/Write sub element in the function file in a
single write operation. It is not necessary to write to every sub element prior to performing a block write. Sub
elements not affected (written to) will have their current value written back to them. For example, if the current
(last read) date and time is 1/1/2001, 12:00.00, DOW = 3, and the hour is changed to 1 o'clock, then the values
written to the device would be 1/1/2001, 1:00.00, DOW = 3.
Instructions
www. kepware.com
Allen-Bradley DF1 Driver Help
14
1. Go to the Function File Options tab in the Device Properties dialog. Check the checkbox labeled Block
write supporting function files?. This notifies the driver to utilize block writes on function files
supporting block writes. The changes will be effective immediately after hitting the OK or Apply buttons.
2. Write the desired value to the sub element tag(s) in question. The sub element tag(s) will immediately
take on the value(s) written to it.
Note: After a sub element is written to at least once in block write mode, the tag's value does not originate
from the controller, but instead from the driver's write cache. After the block write is done, all sub
element tag values will originate from the controller.
3. Once the entire desired sub elements are written to, the block write that will send these values to the
controller may be performed. To instantiate a block write, reference tag address RTC:<element>._SET.
Setting this tag's value to "True" will cause a block write to occur based on the current (last read) sub
elements and the sub elements affected (written to). The _SET tag is treated as a Write Only tag;
meaning, a write to this tag is not reflected in subsequent reads on it. Setting this tag's value to "False"
performs no action.
SLC500 Slot Configuration
SLC500 models with modular I/O racks need to be configured for use with the Allen-Bradley DF1 driver if the I/O
is to be accessed by the driver. Up to 30 slots can be configured per device. To use the slot configuration dialog,
follow the instructions below.
1. Select the slot that will be configured by left-clicking on the row in the slot/module list box.
2. To select a module, left-click on it from the available modules list box.
3. Click Add to add the module.
4. To remove a module, select the slot in the slot/module list box and then click Remove.
Note: The module selections available are the same as those in the Allen Bradley APS software.
Users must know the number of input and output words in each slot. In order to address the I/O in a particular
slot, all slots up to and including that slot must be configured with I/O. For example, if a user is only interested in
the I/O in slot 3, the I/O for slots 1 and 2 must be configured.
See Also: SLC 500 Modular I/O Selection Guide
SLC 500 Modular I/O Selection Guide
The following table lists the number of input and output words available for each I/O module in the Slot
Configuration list.
Module Type
Input Words
Output Words
1746-I*8 Any 8 pt Discrete Input Module
1
0
1746-I*16 Any 16 pt Discrete Input Module
1
0
1746-I*32 Any 32 pt Discrete Input Module
2
0
1746-O*8 Any 8 pt Discrete Output Module
0
1
1746-O*16 Any 16 pt Discrete Output Module
0
1
1746-O*32 Any 32 pt Discrete Output Module
0
2
1746-IA4 4 Input 100/120 VAC
1
0
1746-IA8 8 Input 100/120 VAC
1
0
1746-IA16 16 Input 100/120 VAC
1
0
1746-IB8 8 Input (Sink) 24 VDC
1
0
1746-IB16 16 Input (Sink) 24 VDC
1
0
1746-IB32 32 Input (Sink) 24 VDC
2
0
1746-IG16 16 Input [TTL] (Source) 5VDC
1
0
1746-IM4 4 Input 200/240 VAC
1
0
1746-IM8 8 Input 200/240 VAC
1
0
1746-IM16 16 Input 200/240 VAC
1
0
www. kepware.com
Allen-Bradley DF1 Driver Help
15
1746-IN16 16 Input 24 VAC/VDC
1
0
1746-ITB16 16 Input [Fast] (Sink) 24 VDC
1
0
1746-ITV16 16 Input [Fast] (Source) 24 VDC
1
0
1746-IV8 8 Input (Source) 24 VDC
1
0
1746-IV16 16 Input (Source) 24 VDC
1
0
1746-IV32 32 Input (Source) 24 VDC
2
0
1746-OA8 8 Output (Triac) 100/240 VAC
0
1
1746-OA16 16 Output (Triac) 100/240 VAC
0
1
1746-OB8 8 Output [Trans] (Source) 10/50 VDC
0
1
1746-OB16 16 Output [Trans] (Source) 10/50 VDC
0
1
1746-OB32 32 Output [Trans] (Source) 10/50 VDC
0
2
1746-OBP16 16 Output [Trans 1 amp] (SRC) 24 VDC
0
1
1746-OV8 8 Output [Trans] (Sink) 10/50 VDC
0
1
1746-OV16 16 Output [Trans] (Sink) 10/50 VDC
0
1
1746-OV32 32 Output [Trans] (Sink) 10/50 VDC
0
2
1746-OW4 4 Output [Relay] VAC/VDC
0
1
1746-OW8 8 Output [Relay] VAC/VDC
0
1
1746-OW16 16 Output [Relay] VAC/VDC
0
1
1746-OX8 8 Output [Isolated Relay] VAC/VDC
0
1
1746-OVP 16 16 Output [Trans 1 amp] (Sink) 24VDC3
0
1
1746-IO4 2 In 100/120 VAC 2 Out [Rly] VAC/VDC3
1
1
1746-IO8 4 In 100/120 VAC 4 Out [Rly] VAC/VDC4
1
1
1746-IO12 6 In 100/120 VAC 6 Out [Rly] VAC/VDC
1
1
1746-NI4 4 Ch Analog Input
4
0
1746-NIO4I Analog Comb 2 in & 2 Current Out
2
2
1746-NIO4V Analog Comb 2 in & 2 Voltage Out
2
2
1746-NO4I 4 Ch Analog Current Output
0
4
1746-NO4V 4 Ch Analog Voltage Output
0
4
1746-NT4 4 Ch Thermocouple Input Module
8
8
1746-NR4 4 Ch Rtd/ Resistance Input Module
8
8
1746-HSCE High Speed Counter/Encoder
8
1
1746-HS Single Axis Motion Controller
4
4
1746-OG16 16 Output [TLL] (SINK) 5 VDC
0
1
1746-BAS Basic Module 500 5/01 Configuration
8
8
1746-BAS Basic Module 5/02 Configuration
8
8
1747-DCM Direct Communication Module (1/4 Rack)
2
2
1747-DCM Direct Communication Module (1/2 Rack)
4
4
1747-DCM Direct Communication Module (3/4Rack)
6
6
1747-DCM Direct Communication Module (Full Rack)
8
8
1747-SN Remote I/O Scanner
32
32
1747-DSN Distributed I/O Scanner 7 Blocks
8
8
1747-DSN Distributed I/O Scanner 30 Blocks
32
32
1747-KE Interface Module, Series A
1
0
1747-KE Interface Module, Series B
8
8
1746-NI8 8 Ch Analog Input, Class 1
8
8
1746-NI8 8 Ch Analog Input, Class 3
16
12
1746-IC16 16 Input (Sink) 48 VDC
1
0
1746-IH16 16 Input [Trans] (Sink) 125 VDC
1
0
1746-OAP12 12 Output [Triac] 120/240 VDC
0
1
1746-OB6EI 6 Output [Trans] (Source) 24 VDC
0
1
1746-OB16E 16 Output [Trans] (Source) Protected
0
1
1746-OB32E 32 Output [Trans] (Source) 10/50 VDC
0
2
1746-OBP8 8 Output [Trans 2 amp] (Source) 24 VDC
0
1
1746-IO12DC 6 Input 12 VDC, 6 Output [Rly
1
1
1746-INI4I Analog 4 Ch. Isol. Current Input
8
8
www. kepware.com
Allen-Bradley DF1 Driver Help
16
1746-INI4VI Analog 4 Ch. Isol. Volt./Current Input
8
8
1746-INT4 4 Ch. Isolated Thermocouple Input
8
8
1746-NT8 Analog 8 Ch Thermocouple Input
8
8
1746-HSRV Motion Control Module
12
8
1746-HSTP1 Stepper Controller Module
8
8
1747-MNET MNET Network Comm Module
0
0
1747-QS Synchronized Axes Module
32
32
1747-QV Open Loop Velocity Control
8
8
1747-RCIF Robot Control Interface Module
32
32
1747-SCNR ControlNet SLC Scanner
32
32
1747-SDN DeviceNet Scanner Module
32
32
1394-SJT GMC Turbo System
32
32
1203-SM1 SCANport Comm Module - Basic
8
8
1203-SM1 SCANport Comm Module - Enhanced
32
32
AMCI-1561 AMCI Series 1561 Resolver Module
8
8
Communicating with RSLogix5000 Family Controllers
The Allen-Bradley DF1 Driver can be used to connect to an RSLogix5000 controller's serial port. Users must
configure the RSLogix5000 Controller Tags to be mapped to the PLC/SLC data tables. For information on enabling
communications, refer to the instructions below.
Note: A NULL Modem cable is required for this connection.
1. To start, open an RSLogix5000 development software application (such as RSLogix5000 or Studio 5000
Logix Designer). Then, select Logic | Map PLC/SLC Messages.
www. kepware.com
Allen-Bradley DF1 Driver Help
17
2. Next, map the tags to the different data files as shown in the image below.
3. Ensure that the Allen-Bradley DF1 Driver and controller have matching settings for the Serial Port and
System Protocol (such as the baud rate, data bits, and parity parameters shown in the images below).
Note: The System Protocol tab's Protocol option should be set to DF1 Point to Point.
www. kepware.com
Allen-Bradley DF1 Driver Help
18
4. Next, create the desired tags within the Allen-Bradley DF1 Driver.
Note: The MicroLogix model is the only model that supports "L" data types, which are 32 bit data types
equivalent to the controller's DINT data type.
www. kepware.com
Allen-Bradley DF1 Driver Help
19
www. kepware.com
Allen-Bradley DF1 Driver Help
20
Data Types Description
Data Type
Description
Boolean
Single bit
Byte
Unsigned 8 bit value
bit 0 is the low bit
bit 7 is the high bit
Char
Signed 8 bit value
bit 0 is the low bit
bit 6 is the high bit
bit 7 is the sign bit
Word
Unsigned 16 bit value
bit 0 is the low bit
bit 15 is the high bit
Short
Signed 16 bit value
bit 0 is the low bit
bit 14 is the high bit
bit 15 is the sign bit
DWord
Unsigned 32 bit value
Long
Signed 32 bit value
BCD
Two byte packed BCD, four decimal digits
LBCD
Four byte packed BCD, eight decimal digits
Float
32 bit IEEE Floating point
String
Null terminated character array
Note: The DWord, Long and LBCD data types are not native to any of the PLC models.
When referencing a 16 bit location as a 32 bit value, the location referenced will be the low word, and the next
successive location will be the high word. For example, if N7:10 selected as a DWord data type, N7:10 would be
the low word and N7:11 the high word.
www. kepware.com
Allen-Bradley DF1 Driver Help
21
Address Descriptions
Address specifications vary depending on the model in use. Select a link from the following list to obtain specific
address information for the model of interest.
Micrologix Addressing
SLC500 Addressing (Fixed I/O processor)
SLC5/01 Addressing
SLC5/02 Addressing
SLC5/03 Addressing
SLC5/04 Addressing
SLC5/05 Addressing
PLC5 Addressing
Micrologix Addressing
File Specific Addressing
Output Files
Input Files
Status Files
Binary Files
Timer Files
Counter Files
Control Files
Integer Files
Float Files
String Files
Long Files
PID Files
Message Files
Function Files
High Speed Counter File (HSC)
Real-Time Clock File (RTC)
Channel 0 Communication Status File (CS0)
Channel 1 Communication Status File (CS1)
I/O Module Status File (IOS)
SLC500 Addressing (Fixed I/O processor)
File Specific Addressing
Output Files
Input Files
Status Files
Binary Files
Timer Files
Counter Files
Control Files
Integer Files
SLC5/01 Addressing
File Specific Addressing
Output Files
Input Files
Status Files
Binary Files
Timer Files
Counter Files
Control Files
Integer Files
www. kepware.com
Allen-Bradley DF1 Driver Help
22
SLC5/02 Addressing
File Specific Addressing
Output Files
Input Files
Status Files
Binary Files
Timer Files
Counter Files
Control Files
Integer Files
SLC5/03 Addressing
File Specific Addressing
Output Files
Input Files
Status Files
Binary Files
Timer Files
Counter Files
Control Files
Integer Files
Float Files
ASCII Files
String Files
SLC5/04 Addressing
File Specific Addressing
Output Files
Input Files
Status Files
Binary Files
Timer Files
Counter Files
Control Files
Integer Files
Float Files
ASCII Files
String Files
SLC5/05 Addressing
File Specific Addressing
Output Files
Input Files
Status Files
Binary Files
Timer Files
Counter Files
Control Files
Integer Files
Float Files
ASCII Files
String Files
PLC5 Addressing
File Specific Addressing
Output Files
Input Files
www. kepware.com
Allen-Bradley DF1 Driver Help
23
Status Files
Binary Files
Timer Files
Counter Files
Control Files
Integer Files
Float Files
ASCII Files
String Files
BCD Files
PID Files
Message Files
Block Transfer Files
Output Files
The syntax for accessing data in an Output file differs depending on the PLC model. Arrays are not supported for
output files. The default data types are shown in bold.
PLC-5 Syntax
Syntax
Data Type
Access
O:<word>
Short, Word, BCD
Read/Write
O:<word>/<bit>
Boolean
Read/Write
O/bit
Boolean
Read/Write
Note: Word and bit address information is in octal for PLC-5 models. This follows the convention of the
programming software.
Micrologix Syntax
Syntax
Data Type
Access
O:<word>
Short, Word, BCD
Read/Write
O:<word>/<bit>
Boolean
Read/Write
O/bit
Boolean
Read/Write
Micrologix models have two types of I/O: embedded I/O and expansion I/O (not applicable for Micrologix 1000).
Embedded I/O resides with the CPU base unit while Expansion I/O plugs into the CPU base unit. The table below
lists the I/O capabilities of each Micrologix model.
Micrologix Model
Embedded I/O
Expansion I/O
1000
Slot 0
N/A
1100
Slot 0
Slots 1-4
1200
Slot 0
Slots 1-6
1400
Slot 0
Slots 1-7
1500
Slot 0
Slots 1-16
The address syntax for Micrologix I/O references a zero-based word offset, not a slot. Thus, calculations must be
done to determine the word offset to a particular slot. This requires knowledge of the modules and their
respective size in words. The table below specifies the size of some available modules; however, it is
recommended that the Micrologix documentation and controller project be consulted in order to determine the
true word size of a module. Instructions and examples in calculating word offset follow the table below.
Micrologix Embedded I/O Word Sizes
Micrologix Model
# Input Words
# Output Words
1000
2
1
1100
6
4
1200
4
4
1400
8
6
1500
4
4
Micrologix Expansion I/O Word Sizes
www. kepware.com
Allen-Bradley DF1 Driver Help
24
Modules
# Input Words
# Output Words
1769-HSC
35
34
1769-IA8I
1
0
1769-IA16
1
0
1769-IF4
6
0
1769-IF4XOF2
8
2
1769-IF8
12
1
1769-IM12
1
0
1769-IQ16
1
0
1769-IQ6XOW4
1
1
1769-IQ16F
1
0
1769-IQ32
2
0
1769-IR6
8
0
1769-IT6
8
0
1769-OA8
0
1
1769-OA16
0
1
1769-OB8
0
1
1769-OB16
0
1
1769-OB16P
0
1
1769-OB32
0
2
1769-OF2
2
2
1769-OF8C
11
9
1769-OF8V
11
9
1769-OV16
0
1
1769-OW8
0
1
1769-OW16
0
1
1769-OW8I
0
1
1769-SDN
66
2
1769-SM1
12
12
1769-SM2
7
7
1769-ASCII
108
108
1762-IA8
1
0
1762-IF2OF2
6
2
1762-IF4
7
0
1762-IQ8
1
0
1762-IQ8OW6
1
1
1762-IQ16
1
0
1762-OA8
0
1
1762-OB8
0
1
1762-OB16
0
1
1762-OW8
0
1
1762-OW16
0
1
1762-IT4
6
0
1762-IR4
6
0
1762-OF4
2
4
1762-OX6I
0
1
Calculation
Output Word Offset for Slot x = # Output Words in Slot 0 through Slot (x-1).
Note 1: The Embedded I/O needs to be taken into account when offsetting to Expansion I/O.
Note 2: The number of Input words does not factor into the calculation for Output Word Offset.
I/O Example
Let
Slot 0 = Micrologix 1500 LRP Series C = 4 Output Words
Slot 1 = 1769-OF2 = 2 Output Words
www. kepware.com
Allen-Bradley DF1 Driver Help
25
Slot 2 = 1769-OW8 = 1 Output Word
Slot 3 = 1769-IA16 = 0 Output Word
Slot 4 = 1769-OF8V = 9 Output Word
Bit 5 of Slot 4 = 4 + 2 + 1 = 7 words = O:7/5
SLC 500 Syntax
The default data type is shown in bold.
Syntax
Data Type
Access
O:<slot>
Short, Word, BCD
Read Only
O:<slot>.<word>
Short, Word, BCD
Read Only
O:<slot>/<bit>
Boolean
Read Only
O:<slot>.<word>/<bit>
Boolean
Read Only
Ranges
PLC Model
Min Slot
Max Slot
Max Word
Micrologix
NA
NA
2047
SLC 500 Open
NA
NA
1
SLC 5/01
1
30
*
SLC 5/02
1
30
*
SLC 5/03
1
30
*
SLC 5/04
1
30
*
SLC 5/05
1
30
*
PLC-5 Family
NA
NA
277**
*The number of Input or Output words available for each I/O module can be found in the Modular I/O
Selection Guide. For slot configuration help, refer to Device Setup.
**Octal.
Examples
Micrologix
Address
O:0
Word 0
O/2
Bit 2
O:0/5
Bit 5
SLC 500 Fixed I/O
Address
O:0
Word 0
O:1
Word 1
O/16
Bit 16
O:1/0
Bit 0 word 1 (same as O/16)
PLC5
Address*
O:0
Word 0
O:37
Word 31 (37 octal = 31 decimal)
O/42
Bit 34 (42 octal = 34 decimal)
O:2/2
Bit 2 Word 2 (same as O/42)
*Addresses are shown in Octal.
SLC 500 Modular I/O
Address
O:1
Word 0 slot 1
O:1.0
Word 0 slot 1 (same as O:1)
O:12
Wword 0 slot 12
O:12.2
Word 2 slot 12
O:4.0/0
Bit 0 word 0 slot 4
O:4/0
Bit 0 slot 4 (same as O:4.0/0)
O:4.2/0
Bit 0 word 2 slot 4
O:4/32
Bit 32 slot 4 (same as O:4.2/0)
www. kepware.com
Allen-Bradley DF1 Driver Help
26
Input Files
The syntax for accessing data in an Input file differs depending on the PLC model. Arrays are not supported for
Input files. The default data types are shown in bold.
PLC-5 Syntax
Syntax
Data Type
Access
I:<word>
Short, Word, BCD
Read/Write
I:<word>/<bit>
Boolean
Read/Write
I/bit
Boolean
Read/Write
Note: Word and bit address information is in octal for PLC-5 models. This follows the convention of the
programming software.
Micrologix Syntax
Syntax
Data Type
Access
I:<word>
Short, Word, BCD
Read/Write
I:<word>/<bit>
Boolean
Read/Write
I/bit
Boolean
Read/Write
Micrologix models have two types of I/O: embedded I/O and expansion I/O (not applicable for Micrologix 1000).
Embedded I/O resides with the CPU base unit while Expansion I/O plugs into the CPU base unit. The table below
lists the I/O capabilities of each Micrologix model.
Micrologix Model
Embedded I/O
Expansion I/O
1000
Slot 0
N/A
1100
Slot 0
Slots 1-4
1200
Slot 0
Slots 1-6
1400
Slot 0
Slots 1-7
1500
Slot 0
Slots 1-16
The address syntax for Micrologix I/O references a zero-based word offset, not a slot. Thus, calculations must be
done to determine the word offset to a particular slot. This requires knowledge of the modules and their
respective size in words. The table below specifies the size of some available modules; however, it is
recommended that the Micrologix documentation and controller project be consulted in order to determine the
true word size of a module. Instructions and examples in calculating word offset follow the table below.
Micrologix Embedded I/O Word Sizes
Micrologix Model
# Input Words
# Output Words
1000
2
1
1100
6
4
1200
4
4
1400
8
6
1500
4
4
Micrologix Expansion I/O Word Sizes
Modules
# Input Words
# Output Words
1769-HSC
35
34
1769-IA8I
1
0
1769-IA16
1
0
1769-IF4
6
0
1769-IF4XOF2
8
2
1769-IF8
12
1
1769-IM12
1
0
1769-IQ16
1
0
1769-IQ6XOW4
1
1
1769-IQ16F
1
0
1769-IQ32
2
0
www. kepware.com
Allen-Bradley DF1 Driver Help
27
1769-IR6
8
0
1769-IT6
8
0
1769-OA8
0
1
1769-OA16
0
1
1769-OB8
0
1
1769-OB16
0
1
1769-OB16P
0
1
1769-OB32
0
2
1769-OF2
2
2
1769-OF8C
11
9
1769-OF8V
11
9
1769-OV16
0
1
1769-OW8
0
1
1769-OW16
0
1
1769-OW8I
0
1
1769-SDN
66
2
1769-SM1
12
12
1769-SM2
7
7
1769-ASCII
108
108
1762-IA8
1
0
1762-IF2OF2
6
2
1762-IF4
7
0
1762-IQ8
1
0
1762-IQ8OW6
1
1
1762-IQ16
1
0
1762-OA8
0
1
1762-OB8
0
1
1762-OB16
0
1
1762-OW8
0
1
1762-OW16
0
1
1762-IT4
6
0
1762-IR4
6
0
1762-OF4
2
4
1762-OX6I
0
1
Calculation
Input Word Offset for Slot x = # Input Words in Slot 0 through Slot (x-1).
Note 1: The Embedded I/O needs to be taken into account when offsetting to Expansion I/O.
Note 2: The number of Output words does not factor into the calculation for Input Word Offset.
I/O Example
Let
Slot 0 = Micrologix 1500 LRP Series C = 4 Input Words
Slot 1 = 1769-OF2 = 2 Input Words
Slot 2 = 1769-OW8 = 0 Input Word
Slot 3 = 1769-IA16 = 1 Input Word
Slot 4 = 1769-OF8V = 11 Input Word
Bit 5 of Slot 3 = 4 + 2 = 6 words = I:6/5
SLC 500 Syntax
The default data type is shown in bold.
Syntax
Data Type
Access
I:<slot>
Short, Word, BCD
Read Only
I:<slot>.<word>
Short, Word, BCD
Read Only
I:<slot>/<bit>
Boolean
Read Only
I:<slot>.<word>/<bit>
Boolean
Read Only
www. kepware.com
Allen-Bradley DF1 Driver Help
28
Ranges
PLC Model
Min Slot
Max Slot
Max Word
Micrologix
NA
NA
2047
SLC 500 Open
NA
NA
1
SLC 5/01
1
30
*
SLC 5/02
1
30
*
SLC 5/03
1
30
*
SLC 5/04
1
30
*
SLC 5/05
1
30
*
PLC-5 Family
NA
NA
277
*The number of Input or Output words available for each I/O module can be found in the Modular I/O
Selection Guide. For more information, refer to Device Setup.
**Octal.
Examples
Micrologix
Address
I:0
Word 0
I/2
Bit 2
I:1/5
Bit 5 word 1
SLC 500 Fixed I/O
Address
I:0
Word 0
I:1
Word 1
I/16
Bit 16
I:1/0
Bit 0 word 1 (same as I/16)
PLC5
Address
I:0
Word 0
I:10
Word 8 (10 octal = 8 decimal)
I/20
Bit 16 (20 octal = 16 decimal)
I:1/0
Bit 0 word 1 (same as I/20)
*Addresses are shown in Octal.
SLC 500 Modular I/O
Address
I:1
Word 0 slot 1
I:1.0
Word 0 slot 1 (same as I:1)
I:12
Word 0 slot 12
I:12.2
Word 2 slot 12
I:4.0/0
Bit 0 word 0 slot 4
I:4/0
Bit 0 slot 4 (same as I:4.0/0)
I:4.2/0
Bit 0 word 2 slot 4
I:4/32
Bit 32 slot 4 (same as I:4.2/0)
Status Files
To access Status files, specify a word and an optional bit in the word. The default data types are shown in bold.
Syntax
Data Type
Access
S:<word>
Short, Word, BCD,
DWord, Long, LBCD
Read/Write
S:<word> [rows][cols]
Short, Word, BCD,
DWord, Long, LBCD*
Read/Write
S:<word> [cols]
Short, Word, BCD,
DWord, Long, LBCD*
Read/Write
S:<word>/<bit>
Boolean
Read/Write
www. kepware.com
Allen-Bradley DF1 Driver Help
29
S/bit
Boolean
Read/Write
*Array types.
The number of array elements (in bytes) cannot exceed the block request size specified. This means that array
size cannot exceed 16 words given a block request size of 32 bytes.
Ranges
PLC Model
Max Word
Micrologix
96
All SLC
96
PLC-5
127
The maximum word location is one less when accessing as a 32 bit data type (Long, DWord or Long BCD).
Examples
Example
Description
S:0
Word 0.
S/26
Bit 26.
S:4/15
Bit 15 word 4.
S:10 [16]
16 Element array starting at word 10.
S:0 [4] [8]
4 by 8 element array starting at word 0.
Binary Files
To access Binary files, specify a file number, a word and optional bit in the word. The default data types are
shown in bold.
Syntax
Data Type
Access
B<file>:<word>
Short, Word, BCD,
DWord, Long, LBCD
Read/Write
B<file>:<word> [rows][cols]
Short, Word, BCD,
DWord, Long, LBCD*
Read/Write
B<file>:<word> [cols]
Short, Word, BCD,
DWord, Long, LBCD*
Read/Write
B<file>:<word>/<bit>
Boolean
Read/Write
B<file>/bit
Boolean
Read/Write
*Array types.
The number of array elements (in bytes) cannot exceed the block request size specified. This means that the
array size cannot exceed 16 words given a block request size of 32 bytes.
Ranges
PLC Model
File Number
Max Word
Micrologix
3-255
255
All SLC
3-255
255
PLC-5
3-999
1999
The maximum word location is one less when accessing as a 32 bit data type (Long, DWord or Long BCD).
Examples
Example
Description
B3:0
Word 0.
B3/26
Bit 26.
B12:4/15
Bit 15 word 4.
B3:10 [20]
20 Element array starting at word 10.
B15:0 [6] [6]
6 by 6 element array starting at word 0.
www. kepware.com
Allen-Bradley DF1 Driver Help
30
Timer Files
Timer files are a structured type whose data is accessed by specifying a file number, an element and a field. The
default data types are shown in bold.
Syntax
Data Type
Access
T<file>:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the usage of each field, refer to the PLC's documentation.
Element Field
Data Type
Access
ACC
Short, Word
Read/Write
PRE
Short, Word
Read/Write
DN
Boolean
Read Only
TT
Boolean
Read Only
EN
Boolean
Read Only
Ranges
PLC Model
File Number
Max Element
Micrologix
3-255
255
All SLC
3–255
255
PLC-5
3-999
1999
Examples
Example
Description
T4:0.ACC
Accumulator of timer 0 file 4.
T4:10.DN
Done bit of timer 10 file 4.
T15:0.PRE
Preset of timer 0 file 15.
Counter Files
Counter files are a structured type whose data is accessed by specifying a file number, an element and a field.
The default data types are shown in bold.
Syntax
Data Type
Access
C<file>:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
Element Field
Data Type
Access
ACC
Word, Short
Read/Write
PRE
Word, Short
Read/Write
UA
Boolean
Read Only
UN
Boolean
Read Only
OV
Boolean
Read Only
DN
Boolean
Read Only
CD
Boolean
Read Only
CU
Boolean
Read Only
Ranges
PLC Model
File Number
Max Element
Micrologix
3–255
255
All SLC
3-255
255
PLC-5
3-999
1999
Examples
Example
Description
C5:0.ACC
Accumulator of counter 0 file 5.
www. kepware.com
Allen-Bradley DF1 Driver Help
31
C5:10.DN
Done bit of counter 10 file 5.
C15:0.PRE
Preset of counter 0 file 15.
Control Files
Control files are a structured type whose data is accessed by specifying a file number, an element and a field. The
default data types are shown in bold.
Syntax
Data Type
Access
R<file>:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
Element Field
Data Type
Access
LEN
Word, Short
Read/Write
POS
Word, Short
Read/Write
FD
Boolean
Read Only
IN
Boolean
Read Only
UL
Boolean
Read Only
ER
Boolean
Read Only
EM
Boolean
Read Only
DN
Boolean
Read Only
EU
Boolean
Read Only
EN
Boolean
Read Only
Ranges
PLC Model
File Number
Max Element
Micrologix
3–255
255
All SLC
3–255
255
PLC-5
3-999
1999
Examples
Example
Description
R6:0.LEN
Length field of control 0 file 6.
R6:10.DN
Done bit of control 10 file 6.
R15:18.POS
Position field of control 18 file 15.
Integer Files
To access Integer files, specify a file number, a word and an optional bit in the word. The default data types are
shown in bold.
Syntax
Data Type
Access
N<file>:<word>
Short, Word, BCD,
DWord, Long, LBCD
Read/Write
N<file>:<word> [rows][cols]
Short, Word, BCD,
DWord, Long, LBCD*
Read/Write
N<file>:<word> [cols]
Short, Word, BCD,
DWord, Long, LBCD*
Read/Write
N<file>:<word>/<bit>
Boolean
Read/Write
N<file>/bit
Boolean
Read/Write
*Array types.
The number of array elements (in bytes) cannot exceed the block request size specified. This means that array
size cannot exceed 16 words given a block request size of 32 bytes.
Ranges
PLC Model
File Number
Max Word
www. kepware.com
Allen-Bradley DF1 Driver Help
32
Micrologix
3-255
255
All SLC
3-255
255
PLC-5
3-999
1999
The maximum word location is one less when accessing as a 32 bit data type (Long, DWord or Long BCD).
Examples
Example
Description
N7:0
Word 0.
N7/26
Bit 26.
N12:4/15
Bit 15 word 4.
N7:10 [8]
8 Element array starting at word 10.
N15:0 [4] [5]
4 by 5 element array starting at word 0.
Float Files
To access Float files, specify a file number and an element. The default data types are shown in bold.
Syntax
Data Type
Access
F<file>:<element>
Float
Read/Write
F<file>:<element> [rows][cols]
Float*
Read/Write
F<file>:<element> [cols]
Float*
Read/Write
*Array type.
The number of array elements (in bytes) cannot exceed the block request size specified. This means that the
array size cannot exceed 8 Floats given a block request size of 32 bytes.
Ranges
PLC Model
File Number
Max Word
Micrologix
3-255
255
All SLC
3-255
255
PLC-5
3-999
1999
Examples
Example
Description
F8:0
Float 0.
F8:10 [16]
16 Element array starting at word 10.
F15:0 [4] [4]
16 Element array starting at word 0.
ASCII Files
To access ASCII file data, specify a file number and a character location. The default data types are shown in
bold.
Syntax
Data Type
Access
A<file>:<char>
Char, Byte*
Read/Write
A<file>:<char> [rows][cols]
Char, Byte*
Read/Write
A<file>:<char> [cols]
Char, Byte*
Read/Write
A<file>:<word offset>/length
String**
Read/Write
*The number of array elements cannot exceed the block request size specified. Internally, the PLC packs two
characters per word in the file, with the high byte containing the first character and the low byte containing the
second character. The PLC programming software allows access at the word level or two-character level. The
Allen-Bradley DF1 driver allows accessing to the character level.
Using the programming software, A10:0 = AB, would result in 'A' being stored in the high byte of A10:0 and 'B'
being stored in the low byte. Using the Allen-Bradley DF1 driver, the two assignments A10:0 = A and A10:1 =
B would result in the same data being stored in the PLC memory.
www. kepware.com
Allen-Bradley DF1 Driver Help
33
**Referencing this file as string data allows access to data at word boundaries like the programming software.
The length can be up to 236 characters. If a string that is sent to the device is smaller in length than the length
specified by the address, the driver null terminates the string before sending it down to the controller.
Ranges
PLC Model
File Number
Max Character
Micrologix
3-255
511
All SLC
3-255
511
PLC-5
3-999
1999
Note: Not all Micrologix and SLC 500 PLC devices support ASCII file types. For more information, refer to the
PLC's documentation.
Examples
Example
Description
A9:0
Character 0 (high byte of word 0).
A27:10 [80]
80 Character array starting at character 10.
A15:0 [4] [16]
4 By 16 character array starting at character 0.
A62:0/32
32 Character string starting at word offset 0.
String Files
To access data in a String file, specify a file number and an element. Strings are 82 character null terminated
arrays. The driver places the null terminator based on the string length returned by the PLC. The default data
types are shown in bold.
Note: Arrays are not supported for String files.
Syntax
Data Type
Access
ST<file>:<element>.<field>
String
Read/Write
Ranges
PLC Model
File Number
Max Word
Micrologix
3-255
255
All SLC
3-255
255
PLC-5
3-999
999
Examples
Example
Description
ST9:0
String 0.
ST18:10
String 10.
BCD Files
To access BCD files, specify a file number and a word. The default data types are shown in bold.
Syntax
Data Type
Access
D<file>:<word>
BCD, LBCD
Read/Write
D<file>:<word> [rows][cols]
BCD, LBCD*
Read/Write
D<file>:<word> [cols]
BCD, LBCD*
Read/Write
*Array types.
The number of array elements (in bytes) cannot exceed the block request size specified. This means that the
array size cannot exceed 16 BCD, given a block request size of 32 bytes.
Ranges
PLC Model
File Number
Max Word
Micrologix
NA
NA
All SLC
NA
NA
www. kepware.com
Allen-Bradley DF1 Driver Help
PLC-5
34
3-999
999
Examples
Example
Description
D9:0
Word 0.
D27:10 [16]
16 Element array starting at word 10.
D15:0 [4] [8]
32 Element array starting at word 0.
Long Files
To access Long files, specify a file number and a DWord. The default data types are shown in bold.
Syntax
Data Type
Access
L<file>:<DWord>
Long, DWord, LBCD
Read/Write
L<file>:<DWord> [rows][cols]
Long, DWord, LBCD*
Read/Write
L<file>:<DWord> [cols]
Long, DWord, LBCD*
Read/Write
*Array types.
The number of array elements cannot exceed 16.
Ranges
PLC Model
File Number
Max Word
Micrologix
3-255
255
All SLC
NA
NA
PLC5
NA
NA
Examples
Example
Description
L9:0
Word 0.
L9:10 [8]
8 Element array starting at word 10.
L15:0 [4] [5]
4 by 5 element array starting at word 0.
Micrologix PID Files
PID files are a structured type whose data is accessed by specifying a file number, an element and a field. The
default data types are shown in bold.
Syntax
Data Type
Access
PD<file>:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
Element Field
Data Type
Access
SPS
Word, Short
Read/Write
KC
Word, Short
Read/Write
TI
Word, Short
Read/Write
TD
Word, Short
Read/Write
MAXS
Word, Short
Read/Write
MINS
Word, Short
Read/Write
ZCD
Word, Short
Read/Write
CVH
Word, Short
Read/Write
CVL
Word, Short
Read/Write
LUT
Word, Short
Read/Write
SPV
Word, Short
Read/Write
CVP
Word, Short
Read/Write
TM
Boolean
Read/Write
AM
Boolean
Read/Write
www. kepware.com
Allen-Bradley DF1 Driver Help
35
CM
Boolean
Read/Write
OL
Boolean
Read/Write
RG
Boolean
Read/Write
SC
Boolean
Read/Write
TF
Boolean
Read/Write
DA
Boolean
Read/Write
DB
Boolean
Read/Write
UL
Boolean
Read/Write
LL
Boolean
Read/Write
SP
Boolean
Read/Write
PV
Boolean
Read/Write
DN
Boolean
Read/Write
EN
Boolean
Read/Write
Ranges
PLC Model
File Number
Max Element
Micrologix
3-255
255
All SLC
NA
NA
PLC-5
*
*
*For more information, refer to PLC5 PID Files.
Examples
Example
Description
PD14:0.KC
Proportional gain of PD 0 file 14.
PD18:6.EN
PID enable bit of PD 6 file 18.
PLC5 PID Files
PID files are a structured type whose data is accessed by specifying a file number, an element and a field. The
default data types are shown in bold.
Syntax
Data Type
Access
PD<file>:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
Element Field
Data Type
Access
SP
Real
Read/Write
KP
Real
Read/Write
KI
Real
Read/Write
KD
Real
Read/Write
BIAS
Real
Read/Write
MAXS
Real
Read/Write
MINS
Real
Read/Write
DB
Real
Read/Write
SO
Real
Read/Write
MAXO
Real
Read/Write
MINO
Real
Read/Write
UPD
Real
Read/Write
PV
Real
Read/Write
ERR
Real
Read/Write
OUT
Real
Read/Write
PVH
Real
Read/Write
PVL
Real
Read/Write
DVP
Real
Read/Write
DVN
Real
Read/Write
www. kepware.com
Allen-Bradley DF1 Driver Help
36
PVDB
Real
Read/Write
DVDB
Real
Read/Write
MAXI
Real
Read/Write
MINI
Real
Read/Write
TIE
Real
Read/Write
FILE
Word, Short
Read/Write
ELEM
Word, Short
Read/Write
EN
Boolean
Read/Write
CT
Boolean
Read/Write
CL
Boolean
Read/Write
PVT
Boolean
Read/Write
DO
Boolean
Read/Write
SWM
Boolean
Read/Write
CA
Boolean
Read/Write
MO
Boolean
Read/Write
PE,
Boolean
Read/Write
INI
Boolean
Read/Write
SPOR
Boolean
Read/Write
OLL
Boolean
Read/Write
OLH
Boolean
Read/Write
EWD
Boolean
Read/Write
DVNA
Boolean
Read/Write
DVHA
Boolean
Read/Write
PVLA
Boolean
Read/Write
PVHA
Boolean
Read/Write
Ranges
PLC Model
File Number
Max Element
Micrologix
*
*
All SLC
NA
NA
PLC-5
3-999
999
*For more information, refer to Micrologix PID Files.
Examples
Example
Description
PD14:0.SP
Set point field of PD 0 file 14.
PD18:6.EN
Status enable bit of PD 6 file 18.
Micrologix Message Files
Message files are a structured type whose data is accessed by specifying a file number, an element and a field.
The default data types are shown in bold.
Syntax
Data Type
Access
MG<file>:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
Element Field
Data Type
Access
IA
Word, Short
Read/Write
RBL
Word, Short
Read/Write
LBN
Word, Short
Read/Write
RBN
Word, Short
Read/Write
CHN
Word, Short
Read/Write
NOD
Word, Short
Read/Write
MTO
Word, Short
Read/Write
www. kepware.com
Allen-Bradley DF1 Driver Help
37
NB
Word, Short
Read/Write
TFT
Word, Short
Read/Write
TFN
Word, Short
Read/Write
ELE
Word, Short
Read/Write
SEL
Word, Short
Read/Write
TO
Boolean
Read/Write
CO
Boolean
Read/Write
EN
Boolean
Read/Write
RN
Boolean
Read/Write
EW
Boolean
Read/Write
ER
Boolean
Read/Write
DN
Boolean
Read/Write
ST
Boolean
Read/Write
BK
Boolean
Read/Write
The following file numbers and maximum element are allowed for each model.
Ranges
PLC Model
File Number
Max Element
Micrologix
3-255
255
All SLC
NA
NA
PLC5
*
*
*For more information, refer to PLC5 Message.
Examples
Example
Description
MG14:0.TO
Ignore if timed out bit of MG 0 file 14.
MG18:6.CO
Continue bit of MG 6 file 18.
PLC5 Message Files
Message files are a structured type whose data is accessed by specifying a file number, an element and a field.
The default data types are shown in bold.
Syntax
Data Type
Access
MG<file>:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
Element Field
Data Type
Access
ERR
Short, Word
Read/Write
RLEN
Short, Word
Read/Write
DLEN
Short, Word
Read/Write
EN
Boolean
Read/Write
ST
Boolean
Read/Write
DN
Boolean
Read/Write
ER
Boolean
Read/Write
CO
Boolean
Read/Write
EW
Boolean
Read/Write
NR
Boolean
Read/Write
TO
Boolean
Read/Write
Ranges
PLC Model
File Number
Max Element
Micrologix
*
*
All SLC
NA
NA
PLC-5
3-999
999
www. kepware.com
Allen-Bradley DF1 Driver Help
38
*For more information, refer to Micrologix Message Files.
Examples
Example
Description
MG14:0.RLEN
Requested length field of MG 0 file 14.
MG18:6.CO
Continue bit of MG 6 file 18.
Block Transfer Files
Block transfer files are a structured type whose data is accessed by specifying a file number, an element and a
field. The default data types are shown in bold.
Syntax
Data Type
Access
BT<file>:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
Element Field
Data Type
Access
RLEN
Word, Short
Read/Write
DLEN
Word, Short
Read/Write
FILE
Word, Short
Read/Write
ELEM
Word, Short
Read/Write
RW
Boolean
Read/Write
ST
Boolean
Read/Write
DN
Boolean
Read/Write
ER
Boolean
Read/Write
CO
Boolean
Read/Write
EW
Boolean
Read/Write
NR
Boolean
Read/Write
TO
Boolean
Read/Write
Ranges
PLC Model
File Number
Max Element
Micrologix
NA
NA
All SLC
NA
NA
PLC-5
3-999
1999
Examples
Example
Description
BT14:0.RLEN
Requested length field of BT 0 file 14.
BT18:6.CO
Continue bit of BT 6 file 18.
High Speed Counter File (HSC)
The HSC files are a structured type whose data is accessed by specifying an element and a field. The default data
types are shown in bold.
See Also: Function File Options
Syntax
Data Type
Access
HSC:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
Element Field
Default Type
Access
ACC
DWord, Long
Read Only
HIP
DWord, Long
Read/Write
LOP
DWord, Long
Read/Write
www. kepware.com
Allen-Bradley DF1 Driver Help
39
OVF
DWord, Long
Read/Write
UNF
DWord, Long
Read/Write
PFN
Word, Short
Read Only
ER
Word, Short
Read Only
MOD
Word, Short
Read Only
OMB
Word, Short
Read Only
HPO
Word, Short
Read/Write
LPO
Word, Short
Read/Write
UIX
Boolean
Read Only
UIP
Boolean
Read Only
AS
Boolean
Read Only
ED
Boolean
Read Only
SP
Boolean
Read Only
LPR
Boolean
Read Only
HPR
Boolean
Read Only
DIR
Boolean
Read Only
CD
Boolean
Read Only
CU
Boolean
Read Only
UIE
Boolean
Read/Write
UIL
Boolean
Read/Write
FE
Boolean
Read/Write
CE
Boolean
Read/Write
LPM
Boolean
Read/Write
HPM
Boolean
Read/Write
UFM
Boolean
Read/Write
OFM
Boolean
Read/Write
LPI
Boolean
Read/Write
HPI
Boolean
Read/Write
UFI
Boolean
Read/Write
OFI
Boolean
Read/Write
UF
Boolean
Read/Write
OF
Boolean
Read/Write
MD
Boolean
Read/Write
Ranges
PLC Model
File Number
Max Element
Micrologix
N/A
254
All SLC
N/A
N/A
PLC5
N/A
N/A
Examples
Example
Description
HSC:0.OMB
Output mask setting for high speed counter 0.
HSC:1.ED
Error detected indicator for high speed counter 1.
Real-Time Clock File (RTC)
The RTC files are a structured type whose data is accessed by specifying an element and a field. The default data
types are shown in bold.
See Also: Function File Options
Syntax
Data Type
Access
RTC:<element>.<field>
Depends on field
Depends on field
The following fields are allowed for each element. For the meaning of each field, refer to the PLC's documentation.
www. kepware.com
Allen-Bradley DF1 Driver Help
40
Element Field
Data Type
Access
YR
Word, Short
Read/Write
MON
Word, Short
Read/Write
DAY
Word, Short
Read/Write
HR
Word, Short
Read/Write
MIN
Word, Short
Read/Write
SEC
Word, Short
Read/Write
DOW
Word, Short
Read/Write
DS
Boolean
Read Only
BL
Boolean
Read Only
_SET (for block writes)
Boolean
Read/Write
Ranges
PLC Model
File Number
Max Element
Micrologix
N/A
254
All SLC
N/A
N/A
PLC5
N/A
N/A
Examples
Example
Description
RTC:0.YR
Year setting for real-time clock 0.
RTC:0.BL
Battery low indicator for real-time clock 0.
Channel 0 Communication Status File (CS0)
To access the communication status file for channel 0, specify a word and optionally a bit in the word. The default
data types are shown in bold.
See Also: Function File Options
Syntax
Data Type
Access
CS0:<word>
Short, Word, BCD, DWord, Long, LBCD
Depends on <word>
and <bit>
CS0:<word>/<bit>
Boolean
Depends on <word>
and <bit>
CS0/bit
Boolean
Depends on <word> a
nd <bit>
Ranges
PLC Model
File Number
Max Element
Micrologix
N/A
254
All SLC
N/A
N/A
PLC5
N/A
N/A
Examples
Example
Description
CS0:0
Word 0.
CS0:4/2
Bit 2 word 4 = MCP.
Note: For more information on CS0 words/bit meanings, refer to the Rockwell documentation.
Channel 1 Communication Status File (CS1)
To access the communication status file for channel 1, specify a word and optionally a bit in the word. The default
data types are shown in bold.
See Also: Function File Options
Syntax
Data Type
Access
www. kepware.com
Allen-Bradley DF1 Driver Help
41
CS1:<word>
Short, Word, BCD,
DWord, Long, LBCD
Depends on <word>
and <bit>
CS1:<word>/<bit>
Boolean
Depends on <word>
and <bit>
CS1/bit
Boolean
Depends on <word>
and <bit>
Ranges
PLC Model
File Number
Max Element
Micrologix
N/A
254
All SLC
N/A
N/A
PLC5
N/A
N/A
Examples
Example
Description
CS1:0
Word 0
CS1:4/2
Bit 2 word 4 = MCP
Note: For more information on CS1 words/bit meanings, refer to the Rockwell documentation.
I/O Module Status File (IOS)
To access the I/O module status file, specify a word and optionally a bit in the word. The default data type for
each syntax is shown in bold.
See Also: Function File Options
Syntax
Data Type
Access
IOS:<word>
Short, Word, BCD,
DWord, Long, LBCD
Depends on <word>
and <bit>
IOS:<word>/<bit>
Boolean
Depends on <word>
and <bit>
IOS/bit
Boolean
Depends on <word>
and <bit>
Ranges
PLC Model
File Number
Max Element
Micrologix
N/A
254
All SLC
N/A
N/A
PLC5
N/A
N/A
Examples
Example
Description
IOS:0
Word 0.
IOS:4/2
Bit 2 word 4.
Note: For a listing of 1769 expansion I/O status codes, refer to the instruction manual.
www. kepware.com
Allen-Bradley DF1 Driver Help
42
Error Descriptions
The following error/warning messages may be generated. Click on the link for a description of the message.
Address Validation
Missing address
Device address '<address>' contains a syntax error
Address '<address>' is out of range for the specified device or register
Device address '<address>' is not supported by model '<model name>'
Data Type '<type>' is not valid for device address '<address>'
Device address '<address>' is Read Only
Array size is out of range for address '<address>'
Array support is not available for the specified address: '<address>'
Serial Communications
COMn does not exist
Error opening COMn
COMn is in use by another application
Unable to set comm parameters on COMn
Communications error on '<channel name>' [<error mask>]
Device Status Messages
Device '<device name>' is not responding
Unable to write to '<address>' on device '<device name>'
Device Specific Messages
Unable to read data starting at <start address> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]
Unable to read data starting at <start address> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]. Block deactivated
Unable to read function file <fun. file address> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]
Unable to read function file <fun. file element> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]. Block deactivated
Unable to read data starting at <start address> on device '<device name>'. Framing error
Unable to read function file <fun. file element> on device '<device name>'. Framing error
Unable to read data starting at <start address> on device '<device name>'. checksum error
Unable to read function file <fun. file element> on device '<device name>'. checksum error
Unable to read data starting at <start address> on device '<device name>'. Slave sink/source full
Unable to read function file <fun. file element> on device '<device name>'. Slave sink/source full
Unable to read data starting at <start address> on device '<device name>'. Slave source empty
Unable to read function file <fun. file element> on device '<device name>'. Slave source empty
Error writing to address '<address>' on device '<device name>' [Status=<STS>, Ext. Status=<EXT.
STS>]
Error writing to address '<address>' on device '<device name>'. Framing error
Checksum error occurred writing to address '<address>' on device '<device name>'
Error writing to address '<address>' on device '<device name>'. Slave sink/source full
Error writing to address '<address>' on device '<device name>'. Slave source empty
Device '<device name>' timed out writing to address '<address>'
Unable to read data starting at <start address> on device '<device name>'. Device replied with a
NAK
Unable to read function file <fun. file element> on device '<device name>'. Device replied with a
NAK
Unable to read data starting at <start address> on device '<device name>'. Memory map error
Unable to read function file <fun. file element> on device '<device name>'. Memory map error
Unable to read data starting at '<start address>' on device '<device name>'. Device replied with an
unexpected NAK. Check device link protocol
Unable to read function file '<fun. file element>' on device '<device name>'. Device replied with
an unexpected NAK. Check device link protocol
Address Validation
The following error/warning messages may be generated. Click on the link for a description of the message.
www. kepware.com
Allen-Bradley DF1 Driver Help
43
Address Validation
Missing address
Device address '<address>' contains a syntax error
Address '<address>' is out of range for the specified device or register
Device address '<address>' is not supported by model '<model name>'
Data Type '<type>' is not valid for device address '<address>'
Device address '<address>' is Read Only
Array size is out of range for address '<address>'
Array support is not available for the specified address: '<address>'
Missing address
Error Type:
Warning
Possible Cause:
A tag address that has been specified statically has no length.
Solution:
Re-enter the address in the client application.
Device address '<address>' contains a syntax error
Error Type:
Warning
Possible Cause:
A tag address that has been specified statically contains one or more invalid characters.
Solution:
Re-enter the address in the client application.
Address '<address>' is out of range for the specified device or register
Error Type:
Warning
Possible Cause:
A tag address that has been specified statically references a location that is beyond the range of supported
locations for the device.
Solution:
Verify that the address is correct; if it is not, re-enter it in the client application.
Device address '<address>' is not supported by model '<model name>'
Error Type:
Warning
Possible Cause:
A tag address that has been specified statically references a location that is valid for the communications protocol
but not supported by the target device.
Solution:
1. Verify that the address is correct; if it is not, re-enter it in the client application.
2. Verify the selected model name for the device is correct.
Data Type '<type>' is not valid for device address '<address>'
Error Type:
Warning
Possible Cause:
A tag address that has been specified statically has been assigned an invalid data type.
www. kepware.com
Allen-Bradley DF1 Driver Help
44
Solution:
Modify the requested data type in the client application.
Device address '<address>' is Read Only
Error Type:
Warning
Possible Cause:
A tag address that has been specified statically has a requested access mode that is not compatible with what the
device supports for that address.
Solution:
Change the access mode in the client application.
Array size is out of range for address '<address>'
Error Type:
Warning
Possible Cause:
A tag address that has been specified statically is requesting an array size that is too large for the address type or
block size of the driver.
Solution:
Re-enter the address in the client application to specify a smaller value for the array or a different starting point.
Array support is not available for the specified address: '<address>'
Error Type:
Warning
Possible Cause:
A tag address that has been specified statically contains an array reference for an address type that doesn't
support arrays.
Solution:
Re-enter the address in the client application to remove the array reference or correct the address type.
Serial Communications
The following error/warning messages may be generated. Click on the link for a description of the message.
Serial Communications
COMn does not exist
Error opening COMn
COMn is in use by another application
Unable to set comm parameters on COMn
Communications error on '<channel name>' [<error mask>]
COMn does not exist
Error Type:
Fatal
Possible Cause:
The specified COM port is not present on the target computer.
Solution:
Verify that the proper COM port has been selected.
Error opening COMn
Error Type:
www. kepware.com
Allen-Bradley DF1 Driver Help
45
Fatal
Possible Cause:
The specified COM port could not be opened due an internal hardware or software problem on the target
computer.
Solution:
Verify that the COM port is functional and may be accessed by other Windows applications.
COMn is in use by another application
Error Type:
Fatal
Possible Cause:
The serial port assigned to a device is being used by another application.
Solution:
Verify that the correct port has been assigned to the channel.
Unable to set comm parameters on COMn
Error Type:
Fatal
Possible Cause:
The serial parameters for the specified COM port are not valid.
Solution:
Verify the serial parameters and make any necessary changes.
Communications error on '<channel name>' [<error mask>]
Error Type:
Serious
Error Mask Definitions:
B = Hardware break detected.
F = Framing error.
E = I/O error.
O = Character buffer overrun.
R = RX buffer overrun.
P = Received byte parity error.
T = TX buffer full.
Possible Cause:
1. The serial connection between the device and the Host PC is bad.
2. The communications parameters for the serial connection are incorrect.
Solution:
1. Verify the cabling between the PC and the device.
2. Verify that the specified communications parameters match those of the device.
Device Status Messages
The following error/warning messages may be generated. Click on the link for a description of the message.
Device Status Messages
Device '<device name>' is not responding
Unable to write to '<address>' on device '<device name>'
Device '<device name>' is not responding
Error Type:
Serious
www. kepware.com
Allen-Bradley DF1 Driver Help
46
Possible Cause:
1. The serial connection between the device and the Host PC is broken.
2. The communications parameters for the serial connection are incorrect.
3. The named device may have been assigned an incorrect Network ID.
4. The response from the device took longer to receive than the amount of time specified in the "Request Timeout"
device setting.
Solution:
1. Verify the cabling between the PC and the device.
2. Verify that the specified communication parameters match those of the device.
3. Verify that the Network ID given to the named device matches that of the actual device.
4. Increase the Request Timeout setting so that the entire response can be handled.
Unable to write to '<address>' on device '<device name>'
Error Type:
Serious
Possible Cause:
1. The serial connection between the device and the Host PC is broken.
2. The communication parameters for the serial connection are incorrect.
3. The named device may have been assigned an incorrect Network ID.
Solution:
1. Verify the cabling between the PC and the device.
2. Verify that the specified communication parameters match those of the device.
3. Verify that the Network ID given to the named device matches that of the actual device.
Device Specific Messages
The following error/warning messages may be generated. Click on the link for a description of the message.
Device Specific Messages
Unable to read data starting at <start address> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]
Unable to read data starting at <start address> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]. Block deactivated
Unable to read function file <fun. file address> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]
Unable to read function file <fun. file element> on device '<device name>' [Status=<STS>, Ext.
Status=<EXT. STS>]. Block deactivated
Unable to read data starting at <start address> on device '<device name>'. Framing error
Unable to read function file <fun. file element> on device '<device name>'. Framing error
Unable to read data starting at <start address> on device '<device name>'. checksum error
Unable to read function file <fun. file element> on device '<device name>'. checksum error
Unable to read data starting at <start address> on device '<device name>'. Slave sink/source full
Unable to read function file <fun. file element> on device '<device name>'. Slave sink/source full
Unable to read data starting at <start address> on device '<device name>'. Slave source empty
Unable to read function file <fun. file element> on device '<device name>'. Slave source empty
Error writing to address '<address>' on device '<device name>' [Status=<STS>, Ext. Status=<EXT.
STS>]
Error writing to address '<address>' on device '<device name>'. Framing error
Checksum error occurred writing to address '<address>' on device '<device name>'
Error writing to address '<address>' on device '<device name>'. Slave sink/source full
Error writing to address '<address>' on device '<device name>'. Slave source empty
Device '<device name>' timed out writing to address '<address>'
Unable to read data starting at <start address> on device '<device name>'. Device replied with a
NAK
Unable to read function file <fun. file element> on device '<device name>'. Device replied with a
NAK
Unable to read data starting at <start address> on device '<device name>'. Memory map error
Unable to read function file <fun. file element> on device '<device name>'. Memory map error
Unable to read data starting at '<start address>' on device '<device name>'. Device replied with an
unexpected NAK. Check device link protocol
www. kepware.com
Allen-Bradley DF1 Driver Help
47
Unable to read function file '<fun. file element>' on device '<device name>'. Device replied with
an unexpected NAK. Check device link protocol
Unable to read data starting at <start address> on device '<device name>'
[Status=<STS>, Ext. Status=<EXT. STS>]
Error Type:
Serious
Possible Cause:
1. Node cannot be found.
2. Duplicate node detected.
Solution:
Check the status and extended status codes that are being returned by the PLC. The codes are displayed in
hexadecimal.
Note:
This error message applies to local node errors. Status code errors in the low nibble of the status code indicate
errors found by the local node. The driver will continue to retry reading these blocks of data periodically. Errors
found by the local node occur when the KF module cannot see the destination PLC on the network for some
reason.
Unable to read data starting at <start address> on device '<device name>'
[Status=<STS>, Ext. Status=<EXT. STS>]. Block deactivated
Error Type:
Serious
Possible Cause:
1. The address requested in the block does not exist in the PLC.
2. Processor is in program mode.
Solution:
Check the status and extended status codes that are being returned by the PLC. The codes are displayed in
hexadecimal.
Note:
This error message applies to remote node errors. Status code errors in the high nibble of the status code
indicate errors found by the PLC. These errors are generated when the block of data the driver is asking for is not
available in the PLC. The driver will not ask for these blocks again after receiving this kind of error. This kind of
error can be generated if the address does not exist in the PLC.
Unable to read function file <fun. file element> on device '<device name>'
[Status=<STS>, Ext. Status=< EXT. STS>]
Error Type:
Serious
Possible Cause:
1. Node cannot be found.
2. Duplicate node detected.
Solution:
Check the status and extended status codes that are being returned by the PLC. The codes are displayed in
hexadecimal.
Note:
This error message applies to local node errors. Status code errors in the low nibble of the status code indicate
errors found by the local node. The driver will continue to retry reading this function file periodically. Errors
found by the local node occur when the KF module cannot see the destination PLC on the network for some
reason.
www. kepware.com
Allen-Bradley DF1 Driver Help
48
Unable to read function file <fun. file element> on device '<device name>'
[Status=<STS>, Ext. Status=< EXT. STS>]. Block deactivated
Error Type:
Serious
Possible Cause:
1. The function file address requested in the block does not exist in the PLC.
2. Processor is in program mode.
Solution:
Check the status and extended status codes that are being returned by the PLC. The codes are displayed in
hexadecimal.
Note:
This error message applies to remote node errors. Status code errors in the high nibble of the status code
indicate errors found by the PLC. These errors are generated when the function file the driver is asking for is not
available in the PLC. The driver will not ask for this function file again after receiving this kind of error. This kind
of error can be generated if the function file address does not exist in the PLC.
Unable to read data starting at <start address> on device '<device name>'.
Framing error
Error Type:
Serious
Possible Cause:
1. Unexpected frame received.
2. Frame size mismatch.
Solution:
The device is returning an invalid read response or one of unexpected size. If this error occurs frequently,
contact Technical Support.
Unable to read function file <fun. file element> on device '<device name>'.
Framing error
Error Type:
Serious
Possible Cause:
1. Unexpected frame received.
2. Frame size mismatch.
Solution:
The device is returning an invalid function file read response or one of unexpected size. If this error occurs
frequently, contact Technical Support.
Unable to read data starting at <start address> on device '<device name>'.
checksum error
Error Type:
Serious
Possible Cause:
There is bad cabling connecting the devices causing noise and checksum errors.
Solution:
Inspect cabling between the Host PC and the device.
Unable to read function file <fun. file element> on device '<device name>'.
Checksum error
Error Type:
www. kepware.com
Allen-Bradley DF1 Driver Help
49
Serious
Possible Cause:
There is bad cabling connecting the devices causing noise and checksum errors.
Solution:
Inspect cabling between the Host PC and the device.
Unable to read data starting at <start address> on device '<device name>'.
Slave sink/source full
Error Type:
Serious
Possible Cause:
The slave device cannot accept anymore requests from the master. The client may be requesting data too fast.
Solution:
The driver will automatically poll and re-poll the slave to empty its source and in turn make room for responses
from requests previously in the full sink. If this error occurs too often, decrease the update rate on suspected
tags.
Unable to read function file <fun. file element> on device '<device name>'.
Slave sink/source full
Error Type:
Serious
Possible Cause:
The slave device cannot accept anymore requests from the master. The client may be requesting data too fast.
Solution:
The driver will automatically poll and re-poll the slave to empty its source and in turn make room for responses
from requests previously in the full sink. If this error occurs too often, decrease the update rate on suspected
function file tags.
Unable to read data starting at <start address> on device '<device name>'.
Slave source empty
Error Type:
Serious
Possible Cause:
The slave device does not have a response prepared for the data request starting at <start address>. The slave
re-poll delay may be set to short.
Solution:
The driver will automatically poll and re-poll the slave in seek of a poll response. If this error occurs too often,
increase the slave re-poll delay on the given channel.
Unable to read function file <fun. file element> on device '<device name>'.
Slave source empty
Error Type:
Serious
Possible Cause:
The slave device does not have a response prepared for the request of function file <fun. file element>. The slave
re-poll delay may be set to short.
Solution:
The driver will automatically poll and re-poll the slave in seek of a poll response. If this error occurs too often,
increase the slave re-poll delay on the given channel.
www. kepware.com
Allen-Bradley DF1 Driver Help
50
Error writing to address '<address>' on device '<device name>'
[Status=<STS>, Ext. Status=<EXT. STS>]
Error Type:
Serious
Possible Cause:
1. Node cannot be found.
2. Duplicate node detected.
3. The address requested in the block does not exist in the PLC.
4. Processor is in program mode.
Solution:
Check the status and extended status codes that are being returned by the PLC. The codes are displayed in
hexadecimal.
Note:
Status code errors in the low nibble of the status code indicate errors found by the local node. Errors found by
the local node occur when the KF module cannot see the destination PLC on the network for some reason.
Status code errors in the high nibble of the status code indicate errors found by the PLC. These errors are
generated when the block of data the driver is asking for is not available in the PLC.
Error writing to address '<address>' on device '<device name>'. Framing
error
Error Type:
Serious
Possible Cause:
1. Unexpected frame received.
2. Frame size mismatch.
Solution:
The device is returning an invalid write response or one of unexpected size. If this error occurs frequently,
contact Technical Support.
Checksum error occurred writing to address '<address>' on device '<device
name>'
Error Type:
Serious
Possible Cause:
There is bad cabling connecting the devices causing noise and checksum errors.
Solution:
Inspect cabling between the Host PC and the device.
Error writing to address '<address>' on device '<device name>'. Slave
sink/source full
Error Type:
Serious
Possible Cause:
The slave device cannot accept any more requests from the master. The client may be requesting data too fast.
Solution:
The driver will automatically poll and re-poll the slave to empty its source and in turn make room for responses
from requests previously in the full sink. If this error occurs too often, decrease the update rate on suspected
tags, not necessarily the tag being written to.
www. kepware.com
Allen-Bradley DF1 Driver Help
51
Error writing to address '<address>' on device '<device name>'. Slave source
empty
Error Type:
Serious
Possible Cause:
The slave device does not have a response prepared for the write request to address < address>. The slave repoll delay may be set to short.
Solution:
The driver will automatically poll and re-poll the slave in seek of a poll response. If this error occurs too often,
increase the slave re-poll delay on the given channel.
Device '<device name>' timed out writing to address '<address>'
Error Type:
Serious
Possible Cause:
1. The device is not responding.
2. The serial connection between the device and the Host PC is broken.
Solution:
Inspect cabling between the Host PC and the device. Verify the device is on and operating properly.
Unable to read data starting at <start address> on device '<device name>'.
Device replied with a NAK
Error Type:
Serious
Possible Cause:
The server sent an invalid response or one of unexpected size.
Solution:
If this error occurs frequently, contact Technical Support.
Unable to read function file <fun. file element> on device '<device name>'.
Device replied with a NAK
Error Type:
Serious
Possible Cause:
The server sent an invalid response or one of unexpected size.
Solution:
If this error occurs frequently, contact Technical Support.
Unable to read data starting at <start address> on device '<device name>'.
Memory map error
Error Type:
Serious
Possible Cause:
There was an error writing to memory on the server.
Solution:
If this error occurs frequently, contact Technical Support.
www. kepware.com
Allen-Bradley DF1 Driver Help
52
Unable to read function file <fun. file element> on device '<device name>'.
Memory map error
Error Type:
Serious
Possible Cause:
There was an error writing to memory on the server.
Solution:
If this error occurs frequently, contact Technical Support.
Unable to read data starting at '<start address>' on device '<device name>'.
Device replied with an unexpected NAK. Check device link protocol
Error Type:
Serious
Possible Cause:
The server either sent an invalid response or one of unexpected size. The server's Protocol Link settings may not
match the device configuration.
Solution:
Ensure that the device's Link Protocol settings match that of the channel's. If this error occurs frequently, contact
Technical Support.
Unable to read function file '<fun. file element>' on device '<device name>'.
Device replied with an unexpected NAK. Check device link protocol
Error Type:
Serious
Possible Cause:
The server either sent an invalid response or one of unexpected size. The server's Protocol Link settings may not
match the device configuration.
Solution:
Ensure that the device's Link Protocol settings match that of the channel's. If this error occurs frequently, contact
Technical Support.
www. kepware.com
Allen-Bradley DF1 Driver Help
53
Index
1
15-Pin Module Connection 12
2
25-Pin Module Connection 12
A
Address '<address>' is out of range for the specified device or register 43
Address Descriptions 21
Address Validation 42
Array size is out of range for address <address> 44
Array support is not available for the specified address <address> 44
ASCII Files 32
Avtron 11
B
BCD 20
BCD Files 33
Binary Files 29
Block Transfer Files 38
Boolean 20
Byte 20
C
Cable Connections 11
Channel 0 Communication Status File 40
Channel 1 Communication Status File 40
Channel Setup 6
www. kepware.com
Allen-Bradley DF1 Driver Help
54
Char 20
Checksum 10
Checksum error occurred writing to address '<address>' on device '<device name>' 50
Communicating with RSLogix5000 Family Controllers 16
Communication Parameters 6
Communications error on '<channel name>' [<error mask>] 45
COMn does not exist 44
COMn is in use by another application 45
Control Files 31
Counter Files 30
D
Data Type '<type>' is not valid for device address '<address>' 43
Data Types Description 20
Device '<device name>' is not responding 45
Device '<device name>' timed out writing to address '<address>' 51
Device address '<address>' contains a syntax error 43
Device address '<address>' is not supported by model '<model name>' 43
Device address <address> is Read Only 44
Device ID 10
Device Setup 10
Device Specific Messages 46
Device Status Messages 45
DWord 20
E
Error Checking 10
Error Descriptions 42
Error opening COMn 44
Error writing to address '<address>' on device '<device name>' [Status=<STS> Ext.
Status=<EXT. STS>] 50
Error writing to address '<address>' on device '<device name>'. Framing error 50
Error writing to address '<address>' on device '<device name>'. Slave sink/source full 50
Error writing to address '<address>' on device '<device name>'. Slave source empty 51
Ethernet Encapsulation 10
www. kepware.com
Allen-Bradley DF1 Driver Help
55
F
Float 10, 20
Float Files 32
Framing 45
Full-Duplex 7
Full Duplex 7
Function File Block Writes 13
Function File Options 13
H
Half-Duplex 7
Half Duplex Master 7
Help Contents 5
High Speed Counter File 38
I
I/O Module Status File 41
Input Files 26
Integer Files 31
K
KF2/KF3 Half Duplex Master 8
L
LBCD 20
Link Protocols 7
Link Settings 6
Long 20
Long Files 34
www. kepware.com
Allen-Bradley DF1 Driver Help
56
M
Mask 45
Micrologix Addressing 21
Micrologix Message Files 36
Micrologix PID Files 34
Missing address 43
Modem Setup 10
O
Output Files 23
Overrun 45
Overview 5
P
Parity 45
PLC5 Addressing 22
PLC5 Message Files 37
PLC5 PID Files 35
Protocol Settings 10
R
Radio Modem 6, 9
Real-Time Clock File (RTC) 39
S
Serial Communications 44
Short 20
SLC 500 Modular I/O Selection Guide 14
SLC5/01 Addressing 21
www. kepware.com
Allen-Bradley DF1 Driver Help
57
SLC5/02 Addressing 22
SLC5/03 Addressing 22
SLC5/04 22
SLC5/05 22
SLC500 Addressing (Fixed I/O processor) 21
SLC500 Connection 12
SLC500 Slot Configuration 14
Station Number 6
Status Files 28
String 20
String Files 33
Supported Devices 10
Supported Protocols 6
Swap PLC-5 Float Words 10
T
Timer Files 30
U
Unable to read data starting at '<start address>' on device '<device name>'. Device replied
with an unexpected NAK. Check device link protocol 52
Unable to read data starting at <start address> on device '<device name>' [Status=<STS> Ext.
Status=<EXT. STS>]. 47
Unable to read data starting at <start address> on device '<device name>' [Status=<STS> Ext.
Status=<EXT. STS>]. Block deac 47
Unable to read data starting at <start address> on device '<device name>'. Checksum
error 48
Unable to read data starting at <start address> on device '<device name>'. Device replied with
a NAK 51
Unable to read data starting at <start address> on device '<device name>'. Framing error 48
Unable to read data starting at <start address> on device '<device name>'. Memory map
error 51
Unable to read data starting at <start address> on device '<device name>'. Slave sink/source
full 49
Unable to read data starting at <start address> on device '<device name>'. Slave source
empty 49
Unable to read function file '<fun. file element>' on device '<device name>'. Device replied
with an unexpected NAK. Check device link protocol 52
www. kepware.com
Allen-Bradley DF1 Driver Help
58
Unable to read function file <fun. file element> on device '<device name>' [Status=<STS> Ext.
Status=<EXT. STS>] 47
Unable to read function file <fun. file element> on device '<device name>' [Status=<STS> Ext.
Status=<EXT. STS>]. Block deac 48
Unable to read function file <fun. file element> on device '<device name>'. Checskum
error 48
Unable to read function file <fun. file element> on device '<device name>'. Device replied with
a NAK 51
Unable to read function file <fun. file element> on device '<device name>'. Framing error 48
Unable to read function file <fun. file element> on device '<device name>'. Memory map
error 52
Unable to read function file <fun. file element> on device '<device name>'. Slave sink/source
full 49
Unable to read function file <fun. file element> on device '<device name>'. Slave source
empty 49
Unable to set comm parameters on COMn 45
Unable to write to <address> on device <device name> 46
W
Word 20
www. kepware.com