BlueTrek CRESCENDO - User guide

Dual mic noise cancellation bluetooth® headset
User guide
Enjoy the ultimate voice control headset.
You only need to say. No voice training required. Let’s start !
English
Get started...
• Fully charge your headset for 2 hours.
• Select the ear bud and ear hook that fit for your ear.
• Wear the headset.
• Press the main button for 5 sec.
LED light
You will hear the welcome message :
“Hi, Welcome to the Bluetrek Crescendo
headset with the BlueGenie Voice Interface.
To get started you’ll need to pair your headset.
Click the main button to enter pair mode.”
Main button
• Follow the instruction, press once on the main button to enter pair mode.
• Enable the Bluetooth® search function on your device. Select “Crescendo” and enter
“0000” as the passcode to contact with the headset.
• To use voice control, press the Main Button, wait for the “Say a command” prompt to
finish, then say your command.
• At any time you can use the “What Can I Say” command to be remember the available
commands.
BLUETREK CRESCENDO I 1
English
Special Commands to access FREE service in USA
You can say “Call Information” to search for local and business listings with
Bing™ 411. Find news, directions, restaurant locations, weather forecasts,
movie showtimes, and more.
You can say “Traffic Conditions” to connect to local 511 services to check
traffic condition in USA. For example, road work, traffic jam, accident
information etc...
Simply set up your speed dial list for customized number
Set up your Speed Dial List
Speed Dial Position
(Please refer to your
phone’s User Manual to
learn how to input them
and program as this table.)
1
Favorite 1 / voice mail
2
Favorite 2
3
Favorite 3
4
Favorite 4
5
Favorite 5
6
Home
7
Office
2 I BLUETREK CRESCENDO
Contact to assign
Save Favarite Number from incoming call
If your mobile phone do not have / support Speed Dial feature, you can save favorite number
on Crescendo headset (A phone number can be saved as a favorite after you have received an
incoming call from that number.) Please see the instructions as below:
1. Press once on the Main Button, wait for the “Say a command “prompt to finish, then say
“Settings menu” command.
2. Say “Save Favorite” command, you will hear the instruction message from the headset and
be asked to tell the favorite position.
3. Say the position you preferred like “Call Favorite 1”, you will hear the confirmation message
from the headset.
4. Answer “Yes” and the phone number will be saved as your favorite.
NOTE : If you have set a favorite number in the mobile phone’s speed dial list and headset
favorite list at same position, when you say the “Call favorite“ command, the number saved in
the headset will be taken finally.
* If you want to remove all favorite numbers set under the headset, you can reset the software
by pressing the Main button together with “Vol+” button for around 7 seconds.
English
Voice Command
The following is a comprehensive list of the available commands.
At any time you can use the “What Can I Say” command to listen the available commands.
Command
Say this to...
What Can I Say?
Tell you all available commands
Pair Mode
Enter the pairing mode
Am I Connected?
Tell you if connected to a phone
Phone command
Connect to phone’s voice recognition function
(if mobile phone supported)
Check Battery
Tell you the status of the headset’s battery level
Redial
Dial the last dialed number
Call Back
Dial the last received number
Call Information
Connect to Bing411 voice search center
4 I BLUETREK CRESCENDO
Call number preset on Speed Dial 1
Call Favorite 2
Call number preset on Speed Dial 2
Call Favorite 3
Call number preset on Speed Dial 3
Call Favorite 4
Call number preset on Speed Dial 4
Call Favorite 5
Call number preset on Speed Dial 5
Call Home
Call number preset on Speed Dial 6
Call Office
Call number preset on Speed Dial 7
Traffic Conditions
Connect to local 511 center for Traffic conditions
Answer
Answer the incoming call
Ignore
Reject the incoming call
Settings Menu
Enter to setting menu
Cancel
Cancel the active operation
Yes
Answer “yes” for yes/no question
No
Answer “no” for yes/no question
BLUETREK CRESCENDO I 5
English
Call Voice mail/ Favorite 1
English
Multi-point function
Multipoint technology which allows you to use one headset with two different Bluetooth
mobile phone simultaneity. Please see the instructions as below:
Enable the multi-point function
1. Pair the headset to the mobile A (Please refer to “pairing” section).
2. Long press the Vol + and the Vol - button together on the headset under stand-by mode,
when heard a “beep”, release the buttons and you will hear “Multi-point on” prompt to
finish, the multi-point function will be enabled.
3. Press Main button and the Vol - button together to reset the hardware, the headset will
turn off automatically.
4. Press and hold the Main button for about 5 seconds to enter into pairing mode, then pair
it to the mobile B.(Please refer to “pairing” section).
5. Turn off and turn on again the headset. Two mobiles will be connected with the headset
automatically.
6 I BLUETREK CRESCENDO
Long press the Vol + and the Vol - button together on the headset under stand-by mode,
when heard a “beep”, release the buttons and you will hear “Multi-point off” prompt to
finish, the multi-point function will be disabled.
Answer a call while talking on the other paired phone
• To answer the second call and put the current call on hold, double press the Main button to swap
• To answer the second call and terminate current call , press once on the Main Button
*To avoid issues switching between calls, suggest using the call control button on the
headset rather than your phone controls.
BLUETREK CRESCENDO I 7
English
Disable the multi-point function
English
Settings menu
Under settings menu, you can set:
• Say a command prompt - Enables or Disables the “Say a command prompt”. With it disabled,
you will hear a beep instead of voice command.
• Incoming call announcement - Enables or Disable the Incoming call ID prompt and voice
answer functions (this function may not available on some phones).
• Save favorite - A phone number can be saved on the headset after you received an incoming call.
• Voice control help
• Turn off voice control - Turns off the voice control. To re-enable, hold the “Vol+” and “Vol-“ button
simultaneously for about 6 seconds.
Reset the Crescendo headset
If the headset fail to communicate or any abnormal behavior, you may need to do hardware reset,
which will make the headset get back to normal work again. If hardware reset doesn’t resolve
your problem, you may need to do software reset, which will deletes all pairing information, reset
the voice interface and reboot headset back to pairing mode.
To do hardware reset, press once on the Main Button together with “Vol-“button.
To do software reset, press main button together with “Vol +” button for 6 sec until the red LED
flashes.
8 I BLUETREK CRESCENDO
Function
Button
Time
Status
Power On
Main button
5 sec
From off
Power Off
Main button
7 sec
From on / Standby
Enter Pairing Mode
Main button
7 sec
From off
Activate Voice control
Main button
Press once
Idle / Pairing / Standby
(when voice control
on)
Answer Call
Main button
Press once
Ringing
Reject Call
Main button
3 sec
Ringing
End Call
Main button
Press once
Active calls
Redial
Main button
Double click
Standby (Connected)
Volume adjust
Vol + / Vol -
Press once
Active calls / Standby
Mic Mute On/Off
Vol + / Vol -
3 sec
Active calls
Turn Voice Control On
Vol + & Vol -
6 sec
Pairing / Standby
Software Reset
Main button & Vol +
7 sec
Pairing / Standby
Hardware Reset
Main button & Vol -
Press once
Any status
BLUETREK CRESCENDO I 9
English
Control the headset by button
English
Firmware update available
Visit our website and check for available firmware updates. More service applications and
languages can be now selected!
For more information, please visit: http://www.bluetrek.com/crescendo/firmware/
Please read the procedure carefully before updating the firmware.
More information and Support
This user manual is just to get you started.
If you are having trouble, visit www.bluetrek.com to download the user manual , which
has full details of all features and functions.
Features may vary depending upon your mobile phone . You can check the compatibility
on our website. You can also check with your phone manufacturer that your handset
supports either handsfree or headset Bluetooth profiles.
Please contact us at support@bluetrek.com before returning the product to your dealer
and we will help you through any difficulty you may have.
Thank you for choosing a BLUETREK® product.
10 I BLUETREK CRESCENDO