WT-1010SA
S
ST
TA
AN
ND
D--A
ALLO
ON
NE
EG
GS
SM
MA
ALLA
AR
RM
MS
SY
YS
ST
TE
EM
M
User Manual
W
R
R
R
W
T
U
A
C
O
P
O
A
T
O
N
S
D
N
B
H
D
WIIIT
TU
UR
RA
AC
CO
OR
RP
PO
OR
RA
AT
TIIIO
ON
NS
SD
DN
NB
BH
HD
D
WT-1010SA USER MANUAL
Sketch of the WT-1010SA
LCD Display
Display Signal
Strength, Programming
Status and etc.
SIM Card Holder
Insert SIM here
GSM Module
GSM Transmission
Lithium-Ion Battery
Back-up when Power Failure
Connector Block
All wiring must be connected
here
Antenna
The antenna must be
well connected before
turn on the terminal
Connection Diagram
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
2
WT-1010SA USER MANUAL
Please check the following packing list:
Name
WT-1010SA Main Unit
Telephone line
Power adapter
Lithium-Ion Back-up Battery
5m GSM terminal antenna
User’s Manual
Quantity
1
1
1
1
1
1
Unit
set
set
set
set
set
set
Contents
1. Introduction to WT-1010SA GSM Alarm System………………………………………………………………………5
2. Main Features of the WT-1010SA……………………………………………………………………………………………………5
3. Installation Instruction……………………………………………………………………………………………………………………6
3.1 Description…………………………………………………………………………………………………………………………………………………6
3.2 WT-1010SA Inputs & Outputs Wiring Instructions………………………………………………………………………………………7
3.3 Installing the SIM Card…………………………………………………………………………………………………………………………………8
3.4 Power up the WT-1010SA……………………………………………………………………………………………………………………………8
3.5 Dialing a number from the attached telephone set……………………………………………………………………………………9
4. WT-1010SA Configuration Instructions (Via Voice)……………………………………………………………………10
4.1 Introduction………………………………………………………………………………………………………………………………………………10
Step1- Enter Programming Mode……………………………………………………………………………………………………………10
Step2- Reset the WT-1010SA Unit…………………………………………………………………………………………………………11
Step3- Programming the Administrator Number……………………………………………………………………………………11
Step4- Setting the Recipient that will receive Alert Messages………………………………………………………………12
Step5- Programming the Area Code………………………………………………………………………………………………………12
Step6- Setting the Function of Adding Area Code when Transmitting an Alarm…………………………………13
Step7- Setting the Delay Time for Transmitting a Dialing Number………………………………………………………13
Step8- Setting for calling a group of Administrator Numbers……………………………………………………………….14
Step9- Setting for Auto Test……………………………………………………………………………………………………………………14
Step10- Setting for PSTN Failure……………………………………………………………………………………………………………18
Step11- Setting for AC Failure…………………………………………………………………………………………………………………19
Step12- Setting for Overcoming GSM Jammers & GSM Tower Failure…………………………………………………20
Step13- Input Settings…………………………………………………………………………………………………………………………….22
Step14- Arm and Disarm the System……………………………………………………………………………………………………23
Step15- Enable the Remote Control………………………………………………………………………………………………………24
Step16- Setting the Automatic Call Answering Feature…………………………………………………………………………25
5. WT-1010SA Configuration Instructions (Via SMS)………………………………………………………………………26
5.1 Time Setting………………………………………………………………………………………………………………………………………………26
5.2 Editing the Message Contents of Auto Test………………………………………………………………………………………………26
5.3 Editing the Input Alert Messages (When High Pulse)………………………………………………………………………………27
5.4 Editing the Input Alert Messages (When No Pulse)…………………………………………………………………………………27
5.5 Output Settings…………………………………………………………………………………………………………………………………………28
5.6 Arm and Disarm the System (Via SMS)……………………………………………………………………………………………………29
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
3
WT-1010SA USER MANUAL
6. Miscellaneous Settings……………………………………………………………………………………………………………………32
7. Technical Specifications………………………………………………………………………………………………………………………………41
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
4
WT-1010SA USER MANUAL
1. Introduction to the WT-1010SA GSM Alarm System
The WT-1010SA GSM Alarm System provides the ideal solution for residential,
commercial applications, rural and farm security where traditional telephone lines are
not available for security system communications. When no telephone service is
available from your home, it ensures that critical alarm information reaches the central
station. The WT-1010SA uses a GSM communicator, no distance limits to receive alarm
calls or remote control the alarm system, it can also call and sends text alerts to 8 preset telephone number when intruder alarm triggers.
2. Main Features of the WT-1010SA
1.
Four digital inputs: The system has the function to send SMS and call to the user
in the event of input triggered. For example, Zone 4 connected to an electric door,
when there is intruder or the electric door is open illegally, WT-1010SA will receive
short circuit impulse on Zone 4 and automatically sends a signal to the pre-set
number and notify the owner.
2.
It is possible to arm/disarm the unit remotely via remote control, SMS or phone
call. Alternatively, it also can connect to the basic telephone to perform arm/disarm.
3.
Input alarm zoning can be edited and programmed up to 50 characters long. You
can use this function to program any languages. You can change the displayed text
by sending a command by SMS to the unit. For examples, changing the zone 4 to
“DOOR OPEN”.
4.
If the alarm zoning is not enough, the system is offering “lopping concept” It can
lop up to 50 zoning.
5.
Three remote control outputs: These open collector outputs (that can sink max
300ma per output) can be turned on and off remotely through a SMS or phone call.
Remote control will be reachable by sending a SMS or phone call with a certain
command. For example SMS/Call in to switch on lighting, air conditional, generator,
sensor or other equipment.
6.
Automatically call to 8 pre-program phone numbers while alarming. The WT1010SA also will SMS to 8 programmable phone number to notify the user if any
intruder.
7.
Open your auto gate with your basic telephone. Connect the WT-1010SA with the
auto gate and your house basic telephone. Besides you can use the WT-1010SA as
your house telephone, you also can open your auto gate by pressing a command at
the basic telephone.
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
5
WT-1010SA USER MANUAL
8.
Most of the countries, GSM Mobile operator offer cheaper call plan compared to
telecom landline. It can connect to the basic telephone to make call and if any
intruder, the WT-1010SA will cut the telephone call and send the alarm messages
first.
9.
In order to prevent professional thief to disconnect GSM by using “GSM Jammer”,
the WT-1010SA will transmit the alarm if signal drop immediately and trigger the
siren
10. The owner will automatically received the SMS text messages for “AC Fail”, “Input
1 – Input 4 Fail”, “GSM Alive” if any of the above having problem.
11. Auto test reporting system – after the owner program the reporting time, the WT1010SA will dial the programmable number to inform that “GSM Alive”. This is to
make sure that in case of emergency, the GSM still functioning well
12. Standby rechargeable battery to prevent power failure or electricity cut off by
intruder. The GSM will function as normal when no electricity supply. LCD display
to check the GSM signal strength and battery capacity
3. Installation Instructions
Note: It is essential that you read the step by step instructions fully prior to installing
and programming the unit
3.1) Description
1. Antenna: connect the antenna to the GSM module; place the antenna as far
as possible from the WT-1010SA and do not leave any coiling of the antenna
cable to avoid radiant interference
2. SIM Card: disable the PIN code and set it to 1234 (default)
For Transmitter Mode (Data or SMS): as with any transmitter, it requires an
identifier, receiver telephone numbers, etc (refer to the complete information
on Programming page)
3. Line Input: connect the line input to the PSTN or ISDN network.
4. Outputs (Back-Up Mode): connect to additional remote controlling outputs.
5. Alarm Input: connect the input to output of the Alarm Panel / Control Panel.
6. Power Supply: connect to a 12VDC power supply
7. Operating State: Approximately 20s after power up check the operating
state indicated by the Power LED: the LED is steady during power up phase,
and then blinks when the connection to the GSM network is established. The
Signal indicator LED will stay lit whenever there is signal.
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
6
WT-1010SA USER MANUAL
3.2) WT-1010SA Inputs and Outputs Wiring Instructions
RLY1 (OUT1), RLY2 (OUT2), RLY3 (OUT3) Remote Controlling Outputs
These open collector outputs can be turned on and off remotely through a SMS. Remote
control will be reachable by sending a SMS with a certain command.
Note: When sending normal SMS with command below, the WT-1010SA will
turn On / Off the output relay and reply a message of output has turned On /
Off to a programmable phone numbers.
ZONE1 (IN1), ZONE2 (IN2), ZONE3 (IN3), ZONE4 (IN4) Inputs
Connect ZONE1, ZONE2, ZONE3 and ZONE4 to inputs panel, when there is a short-circuit impulse
on (ZONE1, ZONE2, ZONE3, ZONE4), the WT1010SA is possible to send SMS to a programmable
phone numbers.
For Example: ZONE4 is connected to an electrical door, when there is intruder or the electrical
door is opened illegally, WT1010SA will receive short-circuit impulse on ZONE4 and will
automatically send a signal to the monitoring station and also send a SMS to notify the owner.
A 2.2K Resistor must be attached along with the sensors for all inputs
Inputs and Outputs Wiring Diagram
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
7
WT-1010SA USER MANUAL
3.3) Installing the SIM Card
Note: Installing the SIM Card. Please be sure the initial 4 digit PIN code of SIM card is
disabled. This can be done by placing it in an unlocked Mobile phone and first checking if
the SIM requested any PIN code. If this is the case the PIN code can be disabled using
the security settings on the phone. Warning! The WT-1010SA identifies only 3V SIM Card.
Proceed as follows:
1.
2.
3.
4.
Slide back the SIM door and lift it up
Slide the SIM card into the SIM door making sure that the clipped corner of the
SIM card lines up with the clipped corner of the SIM holder
Close the SIM door
Slide the SIM door to lock the SIM card in place
3.4) Power up the WT-1010SA
When power up the WT-1010SA, it will display as below
LOADING :>>>>>
WAITING…
When the terminal is ready to use, it will display as below
Power
Signal
WT-1010
Battery
Note: Whenever the WT-1010SA fails to logon to network or fails to detect the SIM card, it will
restart automatically until it has detected the SIM card or successfully logon to network.
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
8
WT-1010SA USER MANUAL
3.5) Dialing a number from the attached telephone set
After the GSM module is connected to the GSM network, an attached fixed line phone
can be used to make calls. If you pick up the phone, you will hear a dial tone. Simply
dial the number you want to call (as if you are dialing from a normal fixed line phone).
You can also dial the WT-1010SA unit’s phone number from another phone, and its
attached phone will ring as a normal landline phone would. If there is a busy tone on the
attached telephone set, either the line you are calling is busy, or the GSM communicator
is busy with previous communication at that moment (for example data transfer to the
monitoring station).
Note: Some telephone sets are sensitive to the GSM radio signal. For this reason you
may hear a characteristic noise in the telephone receiver when calling. If the noise is
disturbing, change the location of the phone set (try to keep it as far as possible from
the WT-1010SA unit antenna). Usually it is possible to find a suitable location for the
phone with minimal level of interference.
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
9
WT-1010SA USER MANUAL
4. WT-1010SA Programming Instructions (Via Fixed Line Phone)
4.1 Introduction
The WT-1010SA can be programmed manually by a connected normal telephone.
Note: Before commencing programming it is advisable to read the below programming
setting instructions thoroughly. To start with programming, user must plug-in a normal
single line phone to TEL1 (Port 1)
Step 1. Enter Programming Mode
Pick up the handset or press hands free, press **123456# to enter programming mode.
If the password has entered correctly, you should see “HAND FREE…” displayed on WT1010SA screen.
Now you may proceed with programming settings.
ENTER
SETTING…
When pick up the handset
ENTER
OK
SETTING…
Password entered correctly
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
10
WT-1010SA USER MANUAL
HAND
FREE…
Programming Mode
Step 2. Reset the WT-1010SA Unit
To reset the unit, you can press *15* to proceed.
REST
ON&OFF:
REST
ON&OFF: 1
Then press 1# to reset
REST
ON&OFF: 1
OK
Note: It is advised that you should reset the WT-1010SA unit before proceeding to the below
programming section
Step 3. Programming the Administrator Number
Continue pressing *1* to start programming the administrator number 1
TEL:
1#
TEL: 13232353646
1#
Enter administrator number 13232353646 for example and ended with #
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
11
WT-1010SA USER MANUAL
TEL:
OK
Number has programmed successfully
You may continue to program administrator number 2, 3, 4, 5, 6, 7 and 8 by pressing
*2* , *3* , *4* , *5* , *6* , *7* , *8*
Step 4. Setting the Recipient that will receive Alert Messages
The unit can send text alerts to 1 or all 8 of the programmed administrator’s numbers.
To do this setting, you can press *18* to proceed.
SECT:
SECT: 11111111
Example: To turn on this function for all recipients
Simply input 11111111#
SECT: 11111111
OK
Note: The input for this setting is an 8 digits value: ON (1) or OFF (0) only. Each of them
represents administrator 1 – 8. Default Value: 10000000
Step 5. Programming the Area Code
To program area code, you can press *9* to proceed.
NEW AREA:
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
12
WT-1010SA USER MANUAL
NEW AREA: 03
Enter area code 03 for example and ended with #
NEW AREA: 03
OK
Area code has programmed successfully
Step 6. Setting the Function of Adding Area Code when Transmitting an Alarm
To turn on/off this function, you can press *14* to proceed.
AREA
ON&&OFF:
AREA
ON&&OFF: 1
To turn on this function simply press 1#
To turn off this function simply press 0#
AREA
ON&&OFF: 1
OK
Default Value: 0
Step 7. Setting the Delay Time for Transmitting a Dialing Number
To set the delay time, you can press *34* to proceed.
DTTRANSMIT:
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
13
WT-1010SA USER MANUAL
DTTRANSMIT: 07
Example: To set the required delay time at 7 seconds
Simply press 07#
DTTRANSMIT: 07
OK
Note: The Delay Time is a 2 digits value range from 00 – 59 seconds (Default: 00 seconds)
Step 8. Setting for calling a group of Administrator numbers
To program the unit to dial a certain group of numbers for PSTN/AC failure or Auto Test,
you can press *29* to proceed.
CALL:
CALL: 5
Example: Setting the unit to dial the first 5 administrator numbers
Simply press 5#
CALL: 5
OK
Step 9. Setting for Auto Test
9.1)
Time Setting
To setup time, you can press *16* to proceed.
TIME:
:
:
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
14
WT-1010SA USER MANUAL
TIME:
08 : 30 : 00
Example: To set the time at 8.30am
Simply input digits and ended with #
TIME:
08 : 30 : 00
9.2)
OK
Setting the Auto Test Report Time Section 1
The system has the function of sending the test report to the administrators at
the programmable time section. The time is entered in 24 Hour format. To
program the auto test report time section 1, you can press *17* to proceed.
DSTM1:
:
:
DSTM1:
12 : 00 : 00
Example: To set the auto test report time at 12.00pm
Simply input digits and ended with #
DSTM1:
12 : 00 : 00
9.3)
OK
Setting the Auto Test Report Time Section 2
The system has the function of sending the test report to the administrators at
the programmable time section. The time is entered in 24 Hour format. To
program the auto test report time section 2, you can press *42* to proceed.
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
15
WT-1010SA USER MANUAL
DSTM2:
:
:
DSTM2:
18 : 00 : 00
Example: To set the auto test report time at 18.00pm
Simply input digits and ended with #
DSTM2:
18 : 00 : 00
OK
Note: Skip this setting if only 1 time section is needed.
9.4)
Setting the Auto Test Report Time Section 3
The system has the function of sending the test report to the administrators at
the programmable time section. The time is entered in 24 Hour format. To
program the auto test report time section 3, you can press *43* to proceed.
DSTM3:
:
:
DSTM3:
23 : 59 : 00
Example: To set the auto test report time at 23.59 pm
Simply input digits and ended with #
DSTM3:
23 : 59 : 00
OK
Note: Skip this setting if only 1 time section is needed.
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
16
WT-1010SA USER MANUAL
9.5)
Enable/Disable the function of dialing the programmed Administrator
number for Auto Test
To turn on this function, you can press *27* to proceed.
DTIMEC
ON&&OFF:
DTIMEC
ON&&OFF: 1
To turn on this function simply press 1#
To turn off this function simply press 0#
DTIMEC
ON&&OFF: 1
OK
Default Value: 0
9.6)
Enable/Disable the generation of SMS Report for Auto Test
To turn on this function, you can press *28* to proceed.
DTIMEM
ON&&OFF:
DTIMEM
ON&&OFF: 1
To turn on this function simply press 1#
To turn off this function simply press 0#
DTIMEM
ON&&OFF: 1
OK
Default Value: 0
Note: Please refer to programming instructions via SMS for editing the message content
of Auto Test on page 26
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
17
WT-1010SA USER MANUAL
Step 10. Setting for PSTN Failure
To turn on this function, you can press *30* to proceed.
PST: ME:
CA1:
OU:
CA2:
PST: ME: 1 OU: 1
CA: 1
AL:
AL: 1
CA2: 1
Example: Setting the unit to generate an Alert Message, call the administrators, generate a
pulse (+V) and sound the audible alarm when PSTN failed.
Simply input 11111#
PST: ME: 1 OU: 1
CA: 1
CA2: 1
AL: 1
OK
Description:
“ME” stands for generation of SMS when PSTN failed. Default: 0
“OU” stands for generation of pulse (+5V) at PIN8 when PSTN failed. Default: 0
“AL” stands for sounding the audible alarm when PSTN failed. Default: 0
“CA1” stands for calling the administrators when PSTN failed. Default: 0
“CA2” stands for calling the administrators when PSTN connected. Default: 0
Value: ON (1) or OFF (0)
Auxiliary PSTN Failure Output Facility via PIN8
In additional to the alarm and text alert on PSTN failure the system also has a permanent +5V
output continuously supplied from the unit via PIN8 output which will remain available for the
period of PSTN unavailable.
Note: PSTN Failure Output facility can be used on alarm panel for alert notification
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
18
WT-1010SA USER MANUAL
Step 11. Setting for AC Failure
To turn on this function, you can press *31* to proceed.
ADC: ME:
AL:
CA1:
CA2:
ADC: ME: 1 AL: 1
CA1: 1
CA2: 1
Example: Setting the unit to generate an Alert Message, call the administrators, generate a
pulse (+5V) and sound the audible alarm when AC failed.
Simply input 1111#
ADC: ME: 1 AL: 1
CA1: 1
CA2: 1
OK
Description:
“ME” stands for generation of SMS when AC failed. Default: 0
“AL” stands for sounding the audible alarm when AC failed. Default: 0
“CA1” stands for calling the administrators when AC failed. Default: 0
“CA2” stands for calling the administrators when AC connected. Default: 0
Value: ON (1) or OFF (0)
Auxiliary Power Down Output Facility via PIN9
In additional to the alarm and text alert on AC failure the system also has a second permanent
+5V output continuously supplied from the battery backup via PIN9 output of the unit which will
remain available for the period of AC unavailable.
Note: Power Down Output facility can be used on alarm panel for alert notification
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
19
WT-1010SA USER MANUAL
Step 12. Setting for Overcoming GSM Jammers & GSM Tower Failure
12.1) Enable/Disable the function of Activate Output Relay 1 when GSM
Jammer is detected
To turn on this function, you can press *38* to proceed.
NETWORK
ON&&OFF:
NETWORK
ON&&OFF: 1
To turn on this function simply press 1#
To turn off this function simply press 0#
NETWORK
ON&&OFF: 1
OK
Note: Alarm siren connected to PIN6 & PIN7 will sound when jammer is detected
12.2) Setting the Parameter for Network Failure
To set the parameter, you can press *39* to proceed.
NETDT1:
NETDT1: 05
RLY1:
RLY1: 05
Example: To set the network failure time for 5 seconds
and the turn on time of Relay 1 for 5 seconds
Simply press 0505#
NETDT1: 05
RLY1: 05
OK
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
20
WT-1010SA USER MANUAL
Description:
“NETDT1” stands for network failure time range from 00 – 59 seconds. Default: 6
seconds.
“RLY1” stands for turn on time of Relay 1 when network fails (00 – 59 seconds), 00
means RLY1 will stay ON permanently.
12.3) Enable/Disable the function of Activate Output Relay 2 when GSM Tower
Failure
To turn on this function, you can press *40* to proceed.
NO SIGNAL
ON&&OFF:
NO SIGNAL
ON&&OFF: 1
To turn on this function simply press 1#
To turn off this function simply press 0#
NO SIGNAL
ON&&OFF: 1
OK
Note: Alarm siren connected to PIN6 & PIN7 will sound when jammer is detected
12.4) Setting the Parameter for GSM Tower Failure
To set the parameter, you can press *41* to proceed.
NETDT2:
NETDT2: 06
RLY2:
RLY2: 10
Example: To set the network failure time for 6 seconds
and the turn on time of Relay 2 for 10 seconds
Simply press 0610#
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
21
WT-1010SA USER MANUAL
NETDT2: 06
RLY2: 10
OK
Description:
“NETDT2” stands for network failure time range from 00 – 59 seconds. Default: 6
seconds.
“RLY2” stands for turn on time of Relay 2 when network fails (00 – 59 seconds), 00
means RLY2 will stay ON permanently.
Step 13. Input Settings
13.1) Turn on the function of Inputs
To turn on the function of input number 1, you can press *24* to proceed.
IN1: OP:
CA1:
CL:
AL:
CA2:
IN1: OP: 1 CL: 1
AL: 1
CA1: 1 CA2: 1
Example: Setting the input 1 to generate an SMS, call the administrators
and sound the audible alarm when it triggered.
Simply input 11111#
IN1: OP: 1 CL: 1
CA1: 1
AL: 1
CA2:1
OK
Description:
“OP” stands for generation of SMS when input triggered (Open). Default: 0
“CL” stands for generation of SMS when input triggered (Close). Default: 0
“AL” stands for sounding the audible alarm when input triggered. Default: 0
“CA1” stands for calling the administrators when input triggered (open). Default: 0
“CA2” stands for calling the administrators when input triggered (close). Default: 0
Value: ON (1) or OFF (0)
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
22
WT-1010SA USER MANUAL
You may continue to activate Input 2, Input 3 and Input 4 functions by pressing *25*,
*26* or *46*
Note: Please refer to programming instructions via SMS for editing the Input Alert messages on
page 27
Step 14. Arm and Disarm the System (Via Fixed Line Phone)
To arm the system, you can press *10* to proceed.
ARM OR DISARM
ON&&OFF:
ARM OR DISARM
ON&&OFF: 1
Example: To arm the system simply press 1#
To disarm the system simply press 0#
ARM OR DISARM
ON&&OFF: 1
OK
System armed successfully
Note: In Armed mode, the WT-1010SA can generate SMS alerts, alarms and dialing the
administrator numbers when the inputs triggered, Auto Test, PSTN failed or AC failed.
Alarm Indicator (When dialing the Administrator numbers):
When Input 1 triggered, it will generates (Beep~) continuous sound
When Input 2 triggered, it will generates (Beep~ x 2) continuous sound
When Input 3 triggered, it will generates (Beep~ x 3) continuous sound
When Input 4 triggered, it will generates (Beep~ x 4) continuous sound
When AC failed, it will generates (Beep~ x 5) continuous sound
When PSTN failed, it will generates (Beep~ x 6) continuous sound
When Auto Test, it will generates (Beep~~~) endless sound
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
23
WT-1010SA USER MANUAL
Step 15. Enable the Remote Control
The WT-1010SA also comes with a RF remote control. It allows you to arm or disarm the
system easily from a close distance. To enable the remote control, you can press *45*
to proceed.
RF STARY
Button C: Activate Relay 1
Button A: Arm
Button D: Activate Relay 2
Button B: Disarm
Press the Arm or Disarm button on Remote
RF STARY
OK
The remote control is activated successfully
Now you are able to arm and disarm the system with remote control
When the system is in Armed Mode, a lock icon will be displayed as shown below
WT-1010
When the system is in Disarmed Mode, an unlock icon will be displayed as shown below
WT-1010
Note: 4 units remote control are allowed on this system
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
24
WT-1010SA USER MANUAL
Step 16. Setting the Automatic Call Answering Feature
The WT-1010SA can be programmed to answer all incoming calls automatically even
there is no fixed line phone attached to it. When the call is answered, it allows the owner
to arm or disarm the system by entering a command from their phone’s keypad. To turn
on this function, you can press *35* to proceed.
AUTO ANSWER
ON&&OFF:
AUTO ANSWER
ON&&OFF: 1
To turn on this function simply press 1#
To turn off this function simply press 0#
AUTO ANSWER
ON&&OFF: 1
OK
Default Value: 0
Note: Once this function is turned on, the attached fixed line phone will not ring when there is an
incoming call.
Arm and Disarm Command via Voice
Press *123456# to arm the system when WT-1010SA answered the call
Press *123456* to disarm the system when WT-1010SA answered the call
Note: 123456 is a 6-digits password that is programmable by *0* function or *PAWO#
command by SMS at page 30 and page 38
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
25
WT-1010SA USER MANUAL
5.
WT-1010SA Programming Instructions (Via SMS)
Programming the WT-1010SA can also be done via SMS commands using your phone.
Any programming command sent by SMS must be in CAPITAL letters. The fields
between square brackets are parameters; do NOT enter the square brackets. When you
send a command, you will receive the answer for the first time even if your GSM number
is not in the administrator list. This happens because the WT-1010SA recognizes any
GSM number as administrator and answers to it.
Warning! The administrator number must be programmed into the WT-1010SA unit first via voice
mode in order to use SMS programming mode.
5.1
Time Setting
To set the time, you can send the following SMS command to the unit. The time is
entered in 24 Hour format.
Text Command:
*SETM#HH:MM:SS
HH stands for 2 digits value: Hour
MM stands for 2 digits value: Minute
SS stands for 2 digits value: Seconds
Example:
When *SETM#08:30:15 is applied, the time 08:30:15 will be stored inside the WT1010SA memory.
Return Message
SETM-OK
5.2
Editing the Message Contents of Auto Test (Up to 50 Characters)
The message contents can be edited and programmed up to 50 characters. You can
change the displayed text by sending the following commands by SMS message to the
unit. Note: Only support normal abc/ABC English text, no special characters.
Text Command:
*TSMS#XXXXXX…
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
26
WT-1010SA USER MANUAL
XXXXXX… stands for message contents
Example:
If you want the SMS Report to display “Status:Online”, you would send the following
SMS message to the unit.
*TSMS#Status:Online
Return Message
TSMS=Status:Online
5.3
Editing the Inputs Alert Messages (When High Pulse)
The Input Alert Message can be edited and programmed up to 50 characters. You can
change the displayed text by sending the following commands by SMS message to the
unit. Note: Only support normal abc/ABC English text, no special characters.
Text Command:
*USE[N]#XXXXXX…
N stands for Input number 1 – 4
XXXXXX… stands for alert message content
Example:
If you want the alert message to display “Garage Opened!” when input 1 triggered;
you would send the following SMS message to the unit.
*USE1#Garage Opened!
Return Message
USE1=Garage Opened!
5.4
Editing the Inputs Alert Messages (When No Pulse)
The Input Alert Message can be edited and programmed up to 50 characters. You can
change the displayed text by sending the following commands by SMS message to the
unit. Note: Only support normal abc/ABC English text, no special characters.
Text Command:
*USC[N]#XXXXXX…
N stands for Input number 1 – 4
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
27
WT-1010SA USER MANUAL
XXXXXX… stands for alert message content
Example:
If you want the alert message to display “Garage Closed!” when input 1 triggered; you
would send the following SMS message to the unit.
*USC1#Garage Closed!
Return Message
USC1=Garage Closed!
5.5
Output Settings
5.5.1
Activate Output Relay to Stay On for a Specific Time
To activate the output relay, you can send a text command via SMS specifying the
number of seconds the output should stay on to the unit. It is possible to set up to
maximum of 99,999 seconds
Text Command:
*RLY[N]#XXXXX
N stands for Output number 1 - 3
XXXXX stands for 5 digits value: The number of seconds (00000-99999)
For example, assume you want to turn on the output relay number 2 for 1 hour, you
would send the following SMS message to the unit.
*RLY2#03600
Return Message
*RLY2#=03600
Sending the following SMS Message to unit would mean turn off the output relay number
1.
*RLY1#00000
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
28
WT-1010SA USER MANUAL
5.6
Arm and Disarm the System (Via SMS)
It is possible to arm and disarm the system by SMS. You can send the following text
command to unit.
Text Command:
*DARM#X
X stands for ON (1) or OFF (0) value
Example:
To arm the system, you can send the following text message to the unit.
*DARM#1
Return Message
ARM
To disarm the system, you can send the following text message to the unit.
*DARM#0
Return Message
DISARM
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
29
WT-1010SA USER MANUAL
6. Miscellaneous Settings
Inquire All Programmed Administrator Number via Voice
To inquire all administrator numbers, you can press *32* to proceed.
ADMIN:
1: 1234567890
All the administrator numbers will be displayed in sequence
Deleting the Administrator Number via Voice
Example: To delete the programmed administrator number 1, you can press *1* to
proceed.
TEL:
1#
TEL:
1#
Simply press # to delete
DEL1:
OK
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
30
WT-1010SA USER MANUAL
Changing the Programming Mode Password via Voice
To change the 6 digits programming mode password, you can press *0* to proceed.
NEW PASSWORD:
NEW PASSWORD:
654321
Input new password and ended with #
NEW PASSWORD:
654321
OK
Inquire the status of the Recipients that will receive Alert Messages via Voice
To inquire the status of the recipients, you can press *19* to proceed.
RECIPIENTS:
11111111
The status will be displayed on screen
Press # to turn back
Checking the Signal Strength via Voice
To check the signal strength, you can press *20* to proceed.
CSQ <23>
The signal strength will be displayed on screen
Press # to turn back
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
31
WT-1010SA USER MANUAL
Setting the Waiting Time for Engaged Call via Voice
In the event the administrator has not answered the call or engaged, it could take a
while for the WT-1010SA to call the next number. You can shorten the time for every
call by programming the waiting time. Press *12* to proceed.
WAIT TIME:
WAIT TIME: 20
Example: To set the waiting time for 20 seconds
Simply input 20 and ended with #
WAIT TIME: 20
OK
Note: The waiting time is a 2 digits value range from 20 – 59 seconds (Default: 30 seconds)
Setting Arm Delay Time (Input 1 Only)
Input 1 can be programmed to arm after a preset time when the Arm button is pressed
or Arm function is activated by fixed line phone. To program the delay time, you can
press *47* to proceed.
ARM TIME:
ARM TIME: 30
Example: To set the arm delay time for 30 seconds
Simply input 30 and ended with #
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
32
WT-1010SA USER MANUAL
OK
Note: The Arm Time is a 2 digits value range from 00 – 59 seconds (Default: 00 seconds)
Enable/Disable System Power Up SMS Notification
The system is able to generate SMS notification whenever the WT-1010SA is turned on.
To enable this function, you can press *48* to proceed.
POWER UP MSG
ON&&OFF:
POWER UP MSG
ON&&OFF: 1
To enable this function simply press 1#
To disable this function simply press 0#
POWER UP MSG
ON&&OFF: 1
OK
Default Value: 0
Enable/Disable System Armed SMS Notification
The system is able to generate SMS notification whenever user armed the WT-1010SA.
To enable this function, you can press *49* to proceed.
ARM MESSAGE
ON&&OFF:
ARM MESSAGE
ON&&OFF: 1
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
33
WT-1010SA USER MANUAL
To enable this function simply press 1#
To disable this function simply press 0#
ARM MESSAGE
ON&&OFF: 1
OK
Default Value: 0
Disable the Remote Control
To disable the remote control, you can press *50* to proceed.
DELETE RF
ON&&OFF:
DELETE RF
ON&&OFF: 1
To disable remote control press 1#
To cancel press 0#
DELETE RF
ON&&OFF: 1
OK
Default Value: 0
Setting the Input Alarm Delay Time (Input 2, 3 and 4 Only)
Input 2, 3 and 4 can be programmed to generate SMS alerts, alarms or dialing
administrator numbers after a preset time when they are triggered. To program the
alarm delay time, you can press *51* to proceed.
IN2D TIME:
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
34
WT-1010SA USER MANUAL
IN2D TIME: 60
Example: To set the alarm delay time for 60ms
Simply input 60 and ended with #
OK
Note: The Alarm Delay Time is a 2 digits value range from 00 – 99ms (Default: 00ms)
You may continue programming Input 3 and Input 4 Alarm Delay Time by pressing
*52* or *53*
Activate Output Relay to stay on for a specific time via Voice
To activate output relay 1 to stay on for a specific time, you can press *21* to proceed.
RLY1:
RE:
RLY1: 00050 RE: 1
Example: To activate relay 1 to stay on for 50 seconds and with SMS
reply from the unit after relay has turned off
Simply input 000501#
RLY1: 00050 RE: 1
OK
Note: “ RE:” stands for generation of SMS when relay off, value: ON (1) or OFF (0)
You may continue to activate relay 2 or relay 3 by pressing *22* or *23*
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
35
WT-1010SA USER MANUAL
Setting the Alarm Time for Audible Alarm via Voice
To set the alarm time for audible alarm, you can press *33* to proceed.
ALARM:
ALARM: 03600
Example: To set the audible alarm to sound for 1 hour when triggered
Simply press 03600#
ALARM: 03600
OK
Note: The alarm time must enter in 5 digits range from 00005 – 99999 (Default: 00010 seconds)
Setting the WT-1010SA to ignore the front dialing digits when dialing the
Administrator number via Voice
This function is useful when the WT-1010SA is connected to the PABX system where
Access Digits are required for Extension Line/Centrex Line. To set the unit to ignore the
front dialing digits, you can press *44* to proceed.
DEL-NUM:
DEL-NUM: 2
Example: To set the unit to ignore first 2 dialing digits
Simply press 2#
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
36
WT-1010SA USER MANUAL
DEL-NUM: 2
OK
Note: The value is 0 – 4 (Default: 0)
Adjusting the Speaker and Microphone Volume level via Voice
To adjust the speaker and microphone volume level, you can press *11* to proceed.
SPK:
MIC:
SPK: 3
MIC: 3
Example: To adjust the speaker volume to 3 and microphone volume to 3
Simply press 33#
SPK: 3
MIC: 3
OK
Note: Both SPK and MIC volume level range from 1 – 4 (Default: 1). Adjust the speaker and
microphone volume to compatible with your alarm panel
Inquire the Software and Hardware Version of WT-1010SA via Voice
To check the software and hardware version of WT-1010SA unit, you can press *13* to
proceed.
HW: 1.1ver
SW: 4.7
ver MW: 1.3ver
The information will be displayed on screen
Press # to turn back
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
37
WT-1010SA USER MANUAL
Inquire All Programmed Administrator Number via SMS
To inquire all the programmed administrator number, you can send the following SMS
command to the unit.
Text Command:
*ADM?#
Example of Return Message
1: 13256997049
2: 15915325252
3: 13456679988
4:
5:
6:
7:
8:
Checking the Signal Strength via SMS
To check the signal strength of the unit, you can send the following SMS command to
the unit.
Text Command:
*CSQ?#
Example of Return Message
CSQ=<28>
Checking the Current Time Status via SMS
To check the current time, you can send the following SMS command to the unit.
Text Command:
*ASTM#
Example of Return Message
TIME-01:35:50
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
38
WT-1010SA USER MANUAL
Changing the Programming Mode Password via SMS
It is possible to change the login password by sending the following SMS command.
Text Command:
*PAWO#XXXXXX
XXXXXX stands for 6 digits New Password
Example:
To change the password to 654321, you would send the following SMS command to the
unit.
*PAWO#654321
Return Message:
PAWO-OK
Inquire the Status of Inputs, PSTN and AC
To inquire the status of inputs, PSTN and AC, you can send the following SMS command
to the unit.
Text Command:
*CTC?#
Example of Return Message
AC: 1
AC Available
PSTN: 0
INPUT1: 0
PSTN Unavailable
INPUT2: 1
INPUT3: 0
Input 1 normal
INPUT4: 0
Input 2 triggered
Input 4 normal
Input 3 normal
Sound the Audible Alarm Manually
It is possible to sound the alarm manually by sending the following SMS command to the
unit, which remain active for the period of time set.
Text Command:
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
39
WT-1010SA USER MANUAL
*ALNF#X
X stands for ON (1) or OFF (0) value
When *ALNF#1 is applied, means audible alarm will sound.
When *ALNF#0 (Default) is applied, means audible alarm will turn off.
Reset the WT-1010SA unit via SMS
To reset the unit, you can send the following command by SMS to the unit.
Text Command:
*REST#XXXXXX
XXXXXX stands for 6 digits password based on *PAWO# (Default: 123456) and it can
be changed anytime.
Return Message
REST-OK
7. Technical Specifications
1. Environment temperature: 0~+50℃
2. Relative humidity: 10%~95%
3. Air pressure: 86~106kpa
4. Environment yawp: ≤60dB (A)
5. Working frequency: GSM900MHz/GSM1800MHz
6. Stability of frequency: better than 2.5PPM
7. Signal sensitivity: -103dBM
8. Transmit power: <2w
9. Power: 220v±15% AC
10. Input Voltage Tolerances: 1~20VDC
11. The max distance between terminal and telephone: 100M
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
40
WT-1010SA USER MANUAL
Warranty
Witura Corporation Sdn Bhd guarantees all WT-1010SA GSM Fixed Wireless
Terminal against defective parts and workmanship. Witura Corporation Sdn
Bhd shall, at its option, repair or replace the defective equipment upon the
return of such equipment to any Witura branch. This warranty applies ONLY
to defects in components and workman-ship and NOT to damage due to
causes beyond the control of Witura, such as incorrect voltage, lightning
damage, mechanical shock, water damage, fire damage, or damage arising
out of abuse and improper application of the equipment.
Note: Wherever possible, return only the PCB to Witura Service Centres.
DO NOT return the enclosure.
The WT-1010SA is a product of
Witura Corporation Sdn Bhd
And is manufactured by
Shenzhen Witura Telecommunications Co., Ltd.
WARNING
For safety reasons, only connect equipment with a
telecommunications compliance label. This includes customer
equipment previously labelled permitted or certified.
WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com
COPYRIGHT ©2009 WITURA CORPORATION SDN BHD
41