IPC-7120 / IPC-5120
Wallmount / Desktop Industrial
Chassis with Front I/O Interfaces
& Expansion Slots
User Manual
Copyright
Advantech Co., Ltd copyrights this documentation in June, 2006. All
rights are reserved. Advantech Co., Ltd. reserves the right to make
improvements in the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of
Advantech Co., Ltd. Information provided in this manual is intended to
be accurate and reliable. However, Advantech Co., Ltd. assumes no
responsibility for its use, or for any infringements of the rights of third
parties which may result from its use.
Acknowledgements
Intel®, Pentium® 4, Pentium® D, Celeron™, and Celeron™ D are
trademarks of Intel Corporation.
IPC-7120, IPC-5120, AIMB-740, AIMB-742, AIMB-744, AIMB-750,
AIMB-760, AIMB-762, AIMB-554, and AIMB-560 are trademarks of
Advantech Co., Ltd.
All other product names or trademarks are the properties of their respective owners.
On-line Technical Support
For technical support and service, please visit our support website at:
http://www.advantech.com/support
Part No. 2002712000
1st Edition
June 2006
Printed in China
IPC-7120 User Manual
ii
A Message to the Customer
Advantech customer services
Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech
equipment is destined for the laboratory or the factory floor, you can be
assured that your product will provide the reliability and ease of operation
for which the name Advantech has come to be known. Your satisfaction
is our primary concern. Here is a guide to Advantech's customer services.
To ensure you get the full benefit of our services, please follow the
instructions below carefully.
Technical support
We want you to get the maximum performance from your products. So if
you run into technical difficulties, we are here to help. For the most frequently asked questions, you can easily find answers in your product documentation. These answers are normally a lot more detailed than the ones
we can give over the phone.
So please consult this manual first. If you still cannot find the answer,
gather all the information or questions that apply to your problem, and
with the product close at hand, call your dealer. Our dealers are well
trained and ready to give you the support you need to get the most from
your Advantech products. In fact, most problems reported are minor and
are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers
every business day. We are always ready to give advice on application
requirements or specific information on the installation and operation of
any of our products.
iii
Product Warranty
Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1.
Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.
2.
Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
3.
If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4.
Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for warranty service.
5.
Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.
IPC-7120 User Manual
iv
Initial Inspection
Before you begin installing your motherboard, please make sure that the
following materials have been shipped:
• IPC-7120 (or IPC-5120) Chassis
• User Manual
• Warranty Card
• Accessory box with a package of screws (for fastening the various disk drives), a pair of mounting brackets, four rubber pads,
and a brace for fixing the power cord.
If any of these items are missing or damaged, contact your distributor or
sales representative immediately. We have carefully inspected the IPC7120 (IPC-5120) mechanically and electrically before shipment. It should
be free of marks and scratches and in perfect working order upon receipt.
As you unpack the IPC-7120 (IPC-5120), check it for signs of shipping
damage. (For example, damaged box, scratches, dents, etc.) If it is damaged or it fails to meet the specifications, notify our service department or
your local sales representative immediately. Also notify the carrier.
Retain the shipping carton and packing material for inspection by the carrier. After inspection, we will make arrangements to repair or replace the
unit.
v
Contents
Chapter
1 General Information ........................................2
1.1
1.2
1.3
1.4
1.5
Introduction ....................................................................... 2
Specifications .................................................................... 3
Power Supply Options....................................................... 4
Environmental Specifications
............................. 4
Dimensional Diagram ....................................................... 5
Figure 1.1: Dimensions of IPC-7120.............................. 5
Figure 1.2: Dimensions of IPC-5120.............................. 5
1.6
1.7
Chapter
Safety Precautions ............................................................. 6
FCC ................................................................................... 7
2 System Setup...................................................10
2.1
Removing the Chassis Cover .......................................... 10
2.2
Installing a Motherboard ................................................. 11
Figure 2.1: Removing the chassis cover ....................... 10
Figure 2.2: Removing the disk drive housing............... 12
Figure 2.3: Yellow label for indicating stub ................. 12
Figure 2.4: Installing a motherboard & its I/O shielding ........13
2.3
Installing add-on cards .................................................... 14
2.4
Installing Disk Drives...................................................... 15
Figure 2.5: Installing an add-on card ............................ 14
Figure 2.6: Removing the 3.5" disk drive bracket ........ 15
Figure 2.7: Installing the disk drives ............................ 16
Figure 2.8: Installing the internal disk drive................. 16
2.5
Bidirectional mounting.................................................... 17
2.6
Front Access I/O Interface Design .................................. 18
Figure 2.9: Bottom and right side mounting................. 17
Figure 2.10: Mounting brace for securing the power cord......18
Chapter
3 Operation ........................................................20
3.1
The Front Bezel of IPC-7120 (IPC-5120)....................... 20
3.1.1
3.1.2
3.2
Switch and Button......................................................... 20
Figure 3.1: Front bezel of IPC-7120............................. 20
Figure 3.2: Front bezel of IPC-5120............................. 20
LED indicators.............................................................. 21
Table 3.1: LED indicator functions .............................. 21
Replacing the Cooling Fan.............................................. 22
3.2.1
3.2.2
Replacing the 12 cm system fan ................................... 22
Figure 3.3: Replacing the 12 cm fan............................. 22
Replacing the 4 cm cooling fan .................................... 23
Figure 3.4: Replacing the 4 cm fan............................... 23
vii
Table of Contents
3.3
Cleaning the Filter........................................................... 24
3.4
Replacing the Power Supply ........................................... 25
Figure 3.5: Cleaning the filter....................................... 24
Figure 3.6: Removing the front bezel ........................... 25
Figure 3.7: Renoving the power supply........................ 26
Figure 3.8: Replacing the front bezel............................ 26
Appendix A
Exploded Diagrams .......................................28
A.1
Exploded Diagram of IPC-7120...................................... 28
A.2
Exploded Diagram of IPC-5120...................................... 29
Figure A.1: Exploded diagram, IPC-7120 .................... 28
Figure A.2: Exploded diagram, IPC-5120 .................... 29
Appendix B Motherboard Options ....................................32
Appendix C Safety Instructions .........................................34
C.1
C.2
English............................................................................. 34
German – Wichtige Sicherheishinweise ......................... 35
IPC-7120 User Manual
viii
CHAPTER
1
General Information
Chapter 1 General Information
1.1 Introduction
The IPC-7120 (IPC-5120) industrial computer chassis is specifically
designed for factory floors and other harsh industrial environments. It is
a wall-mountable/desktop unit that is ideal for system integrators or users
who require a compact and rugged computing platform for industrial
automation applications. The IPC-7120 (IPC-5120) supports a wide range
computing peripherals to be integrated with the chassis. Standard ATX
motherboards with up to seven add-on cards may be installed in the IPC7120. (MicroATX motherboards with up to four add-on cards may be
installed in the IPC-5120).
Outstanding ID and mechanical designs
Unlike the classical industrial computer, IPC-7120 (IPC-5120) has an
innovated appearance for industrial computer chassis. It can be placed on
the desk or mounted bi-directionally by the supplied brackets. It can be
easily bottom or right mounted onto most surfaces, such as walls or workbenches. The shockproof disk drive housing design protects the system
against harsh industrial environments or unexpected shock. The front
access I/O interfaces and expansion slots make it much easier to operate
and maintain while it is installed in the ATM machine, medical equipment and other huge machine. All these outstanding features make IPC7120 (IPC-5120) the best solution for price, performance and total cost of
ownership.
IPC-7120 User Manual
2
1.2 Specifications
• Construction: Heavy-duty steel
• Disk drive capacity: one 5.25" CD-ROM drive (or CD-R/W drive or
DVD-ROM drive); one 3.5" FDD or HDD; and one internal 3.5" disk
drive
• I/O interfaces on front bezel: up to seven expansion slots on the front
(four expansion slots for IPC-5120). (The exact number of I/O interfaces are determined by the particular motherboard installed.)
• LED Indicators on front bezel: single-color LED (green) for Power;
single-color LED (orange) for HDD activity
• Switches and buttons on the front bezel: Power button and System
Reset button
• Cooling fans: One 85 CFM (12 cm x 12 cm) cooling fan with air filter
near the rear of the chassis; one 10 CFM (4 cm x 4 cm) fan under the
disk drive housing for providing better air flow for the storage devices
• Air filter: One washable and reusable filter mounted near the rear of
the chassis
• Gross weight: 9 kg (19.8 lb) for IPC-7120; 8 kg (17.6 lb) for IPC-5120
• Dimensions (WxHxD): 380 mm x 164 mm x 307 mm (15"x 6.5" x
12.1") for IPC-7120; 320 mm x 164 mm x 307 mm (12.6"x 6.5" x
12.1") for IPC-5120
3
Chapter 1
1.3 Power Supply Options
Table 1.1: Power Supply Options
Model Name
1757000229
Watt
300 W max. (ATX, PFC)
Input rating
100 ~ 240 Vac (Full range)
Output voltage
+5 V @ 25 A, +3.3 V @ 14 A, +12 V @ 16 A, -5 V @
0.5 A, -12 V @ 1.0 A, +5 Vsb @ 2 A
Minimum load
+5 V @ 3 A, +3.3 V @ 1.0 A, +12 V @ 2 A, -5 V @
0.05 A, -12 V @ 0.05 A, +5 Vsb @ 0.1 A
MTBF
100,000 hours @ 25° C
Safety
UL/TUV/CB/CCC
1.4 Environmental Specifications
Table 1.2: Environmental Specifications
Environment
Operating
Non-operating
Temperature
0° to 40°C
(32° to 104°F)
-20° to 60°C
(-4° to 140°F)
Humidity
10 to 85% @ 40°C,
non-condensing
10 to 95% @ 40°C,
non-condensing
Vibration
1G rms
2G
Safety
CE compliant
IPC-7120 User Manual
4
1.5 Dimensional Diagram
Unit: mm [inch]
Figure 1.1: Dimensions of IPC-7120
Unit: mm [inch]
Figure 1.2: Dimensions of IPC-5120
5
Chapter 1
1.6 Safety Precautions
Warning!
Always completely disconnect the power cord
from your chassis whenever you work with the
hardware. Do not make connections while the
power is on. Sensitive electronic components
can be damaged by sudden power surges. Only
experienced electronics personnel should open
the PC chassis
Caution!
Always ground yourself to remove any static
charge before touching the motherboard, backplane, or add-on cards. Modern electronic
devices are very sensitive to static electric
charges. As a safety precaution, use a grounding
wrist strap at all times. Place all electronic components on a static-dissipative surface or in a
static-shielded bag when they are not in the
chassis.
IPC-7120 User Manual
6
1.7 FCC
This device complies with the requirements in part 15 of the FCC rules:
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired operation
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
device in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his/her
own expense. The user is advised that any equipment changes or modifications not expressly approved by the party responsible for compliance
would void the compliance to FCC regulations and therefore, the user's
authority to operate the equipment.
7
Chapter 1
CHAPTER
2
System Setup
Chapter 2 System Setup
The following procedures are intended to aid installation of a motherboard, add-on cards, and disk drives into the IPC-7120 (IPC-5120).
Please also refer to Appendix A, Exploded Diagram, for all the parts of
the IPC-7120 (IPC-5120).
Note:
Use caution when installing or operating the
components with the chassis open. Be sure to
turn off the power, unplug the power cord and
ground yourself by touching the metal chassis
before you handle any components inside the
machine.
2.1 Removing the Chassis Cover
To remove the top cover of IPC-7120 (IPC-5120), refer to Figure 2.1 and
proceed as follows:
1.
Loosen the two thumb screws on the rear top of the chassis.
2.
Remove the chassis top cover by gently sliding it backwards.
Figure 2.1: Removing the chassis cover
IPC-7120 User Manual
10
2.2 Installing a Motherboard
The IPC-7120 supports standard ATX and microATX motherboards. The
IPC-5120 supports the microATX motherboard only. Please refer to the
following procedures to install a motherboard.
Note:
Use caution when installing a motherboard. It is
highly recommended to integrate the Advantech motherboard series to ensure the optimum
performance quality, safety and the best airflow. If users insist on using other motherboard
brands, please be aware that the CPU cooler
should be under 55 mm height or under 80 mm
height if removing the 3.5" disk drive brackets
from the drive housing. Otherwise, components
may be obstructed on the motherboard and the
chassis, affecting the air flow inside the chassis.
1.
Loosen the four screws on the top of the disk drive housing and
then lift it up. (see Figure 2.2)
2.
Attach the motherboard I/O shielding onto the front panel.
3.
There is a yellow warning label located inside of the chassis bottom
of the IPC-7120, (see Figure 2.3). This label indicates if the copper
stubs (supplied in the accessory box) should be attached on the
chassis for fixing the various ATX motherboards. Be sure to follow
the instructions and affix the motherboard on the chassis in the correct stub locations. ( The IPC-5120 isn’t supplied with this label
because it is designed for microATX motherboards with fixed
stand-offs. ) (see Figure 2.4)
4.
Connect the 20-pin (or 24-pin) ATX power connector and the 4-pin
+12V power connector from the power supply to the motherboard.
5.
Inside the top left of the front panel, there are four wires with the
connectors marked “POWER SW”, “RESET SW“, “HDD LED”,
“POWER LED” individually. Please plug them onto the corresponding connectors of the motherboard according to your motherboard manual.
6.
Plug the two fan power connectors onto the motherboard according
to your motherboard manual.
11
Chapter 2
Figure 2.2: Removing the disk drive housing
STAND-OFF MARK
BP/MP MODEL
PCA-6108P6X
PCA-6108E
PCA-6108P4
PCA-6108P6
PCA-6108P8
PCE-5B07
AIMB-744
AIMB-750
AIMB-760
A M
B
*
AIMB-740
AIMB-741
AIMB-742
AIMB-762
AIMB-554
AIMB-560
*
*
*
*
*
*
*
*
1.The stubs are in the accessory box.
Be sure to attach the necessary
stubs on the chassis.
2.Be careful to screw the stub under
10 kgf cm.
Figure 2.3: Yellow label for indicating stub locations
IPC-7120 User Manual
12
Figure 2.4: Installing a motherboard & its I/O shielding
13
Chapter 2
2.3 Installing add-on cards
The IPC-7120 supports up to seven add-on cards with an Advantech ATX
motherboard. The IPC-5120 supports up to four add-on cards with an
Advantech microATX motherboard. To install an add-on card, please
proceed as follows:
1.
Undo the four screws on the top of the disk drive housing and then
lift it up.
2.
Select a vacant slot and remove its corresponding I/O bracket,
which is attached to the front panel.
3.
Insert an add-on card into the slot. Fasten the card by a screw on
the top of the I/O bracket. (see Figure 2.5)
4.
Repeat Step 2 and 3 if there is more than one card to be inserted.
5.
Replace the disk drive housing and fasten it.
Figure 2.5: Installing an add-on card
IPC-7120 User Manual
14
2.4 Installing Disk Drives
To install a CD-ROM drive (or CD-R/W drive or DVD-ROM drive),
HDD or FDD, please refer to these detailed procedures:
1.
Loosen the four screws on top of the disk drive housing and then
lift it up.
2.
Users can remove the 3.5" disk drive bracket completely from the
housing by loosening the two screws and then separating it from
the hooks by sliding it backwards. (see Figure 2.6)
3.
Insert the disk drive into the proper location in the disk drive housing, and fix it with the supplied screws. (see Figure 2.7)
4.
Connect a 34-pin flat cable from the motherboard to a FDD, or a
40-pin flat cable to the IDE HDD or CD-ROM drive (or CD-RW
drive or DVD-ROM drive, etc.), or a SATA cable to a SATA HDD.
Then plug the power connector in to each disk drive.
5.
Replace the disk drive housing and then fasten it with four screws.
6.
There is another disk drive bracket fixed on the inside of the rear
plate. If users want to install a 3.5" HDD, simply unfasten the four
screws from outside of the rear plate and then remove it from the
hook. (see Figure 2.8)
7.
Fasten the HDD into this bracket properly. The
four screws used to fasten the bracket are
supplied with rubber cushions; the
rubber cushions should be
inserted between the HDD and
the chassis when fastening the
screws. The cushions protect
the HDD from shock and
vibration.
8.
Replace this bracket to the
hook and fasten the four
screws from outside of the rear
plate.
Figure 2.6: Removing the 3.5" disk drive bracket
15
Chapter 2
Figure 2.7: Installing the disk drives
Figure 2.8: Installing the internal 3.5” disk drive
IPC-7120 User Manual
16
2.5 Bidirectional mounting
Traditionally, industrial computer chassis support I/O interfaces on the
backside of the unit. For some special environments like computer telephony, ATM machines, gaming machines, and large-scale robot applications, it is inconvenient for technicians to maintain or access the cables.
However, it is always necessary to make some space between the chassis
and the wall. To help eliminate these limitations, the IPC-7120 (IPC5120) offers bi-drectional, horizontal and vertical mounting.
The IPC-7120 (IPC-5120) has two accessory brackets for mounting on
the bottom, or alternatively, on the right side of the chassis (see Figure
2.9) These brackets permit users to mount the chassis onto most vertical
and horizontal surfaces: a wall, a system panel, a workbench, a system
housing, or a table.
Besides the above mounting methods, the IPC-7120 (IPC-5120) can be
placed on top of a desktop. In this case, affix the rubber pads (four items)
supplied for this purpose on the chassis bottom, and in alignment with the
"L" marks.
Figure 2.9: Bottom and right side mounting
17
Chapter 2
2.6 Front Access I/O Interface Design
One of the unique design features of the IPC-7120 (IPC-5120) is that the
I/O interfaces and expansion slots are located on the front of the chassis.
This arrangement helps to eliminate most typical accessibility problems,
and saves more space if the unit must be mounted on a wall or a workbench.
An added design feature is the convenience of the mounting brace for
securing the power cord on the IPC-7120 (IPC-5120). Users can find the
mounting brace in the accessory box. (see Figure 2.10)
Figure 2.10: Mounting brace for securing the power cord
IPC-7120 User Manual
18
CHAPTER
3
Operation
Chapter 3 Operation
3.1 The Front Bezel of IPC-7120 (IPC-5120)
On the front bezel, there is one Power On/Off switch, one System Reset
button and two LED indicators. Individual functions are described
below:
3.1.1 Switch and Button
Power On/Off button: Press this button to turn on/off the system power.
Please use system shutdown or press this switch for few seconds to turn
off the system ATX power.
System Reset button: Press this button to reboot the system.
Figure 3.1: Front bezel of IPC-7120
Figure 3.2: Front bezel of IPC-5120
IPC-7120 User Manual
20
3.1.2 LED indicators
Table 3.1: LED indicator functions
LED
Description
Power
System power
Hard Disk
Hard disk drive activity
Power LED: Always green color while the system power is on.
HDD LED: Flashing orange color while the HDD data is accessing.
21
Chapter 3
3.2 Replacing the Cooling Fan
There are two cooling fans that provide good airflow inside the IPC-7120
(IPC-5120). To replace these fans, proceed as follows:
3.2.1 Replacing the 12 cm system fan
1.
Remove the chassis top cover and the disk drive housing.
2.
Take out the filter first.
3.
Disconnect the cooling fan power connector.
4.
Loosen the four screws from outside the rear plate and then gently
remove the fan module. Loosen four screws on the fan bracket and
the four screws on the rear side of the module (not the screws on
the fan) and replace it with a new fan. (see Figure 3.3)
5.
Attach the new cooling fan on the bracket by screwing in the four
screws.
6.
Reattach the fan power connector.
7.
Replace the fan module into the chassis and then screw the four
screws onto the rear of the chassis.
Figure 3.3: Replacing the 12 cm fan
IPC-7120 User Manual
22
3.2.2 Replacing the 4 cm cooling fan
1.
Remove the chassis top cover and the disk drive housing.
2.
Unplug the fan power connector.
3.
Loosen the one screw on the fan bracket and then take out the fan
module.
4.
Undo the two screws on the fan bracket so that you can take out the
fan. (see Figure 3.4)
5.
Replace the fan with a new one and then attach it to the bracket.
6.
Fasten the fan module onto the chassis.
7.
Replace the disk drive housing into the chassis and then fasten it.
Figure 3.4: Replacing the 4 cm fan
23
Chapter 3
3.3 Cleaning the Filter
The filter prevents dust or particles from entering the work environment
and extends longevity of the system. It's better to clean the filter periodically. There is one easy-to-maintain filter near the back of the chassis.
To take out this filter, refer to Figure 3.5 and proceed as follows:
1.
Remove the chassis top cover.
2.
Pull out the fan filter by pushing the hook on top of it.
3.
Clean the filter with a soft brush or wash the dust away from the
filter with water and then dry it.
4.
Replace it.
Figure 3.5: Removing the filter
IPC-7120 User Manual
24
3.4 Replacing the Power Supply
The IPC-7120 (IPC-5120) supports a 1U-high ATX power supply. To
change the power supply, please proceed as follows:
1.
Unplug the AC inlet from the power supply.
2.
Remove the chassis top cover and the disk drive housing.
3.
Unplug the 20-pin (or 24-pin) ATX power connector and 4-pin
+12V power connector from the motherboard, as well as the power
connectors from all disk drives.
4.
Remove the front bezel by gently poking out the four hooks on the
inside of the front chassis. (see Figure 3.6)
5.
Loosen the two screws on the outside of the chassis on the left side,
along with the two screws on the front of the chassis. Then take out
the power supply. (see Figure 3.7)
6.
Place a new power supply inside and fasten it onto the chassis.
7.
Plug the 20-pin (or 24-pin) ATX power connector and 4-pin +12V
power connector to the motherboard and plug the other power connectors to the disk drives and peripherals.
8.
Replace the front bezel. Align the three hooks on the bottom of the
chassis first, and then tip the bezel into place on top. (see Figure
3.8) Gently push the top hooks inside to reattach the bezel to chassis.
9.
Replace the disk drive housing and the top cover.
Figure 3.6: Removing the front bezel
25
Chapter 3
Figure 3.7: Renoving the power supply
Figure 3.8: Replacing the front bezel
IPC-7120 User Manual
26
Appendix
Exploded Diagram
A
Appendix A Exploded Diagrams
A.1 Exploded Diagram of IPC-7120
Figure A.1: Exploded diagram, IPC-7120
IPC-7120 User Manual
28
A.2 Exploded Diagram of IPC-5120
Figure A.2: Exploded diagram, IPC-5120
29
Appendix A
Appendix
B
Motherboard Options
Appendix B Motherboard Options
The IPC-7120 supports a variety of Advantech ATX and microATX
motherboards listed below. The IPC-5120 supports microATX motherboards only. Please contact a local sales representative for more detailed
information about each model.
Table B.1: ATX Motherboard Options
Model Name
Bus
PCI
PCI/ISA
ISA
AGP
SATA
AIMB-740-B
4 (32-bit)
1
1
--
--
AIMB-7406CB1
5 (32-bit)
--
--
--
--
AIMB-742
4 (32-bit)
1
1
1 (8X) --
AIMB-744
2 (PCI-X 64-bit)
4 (PCI 32-bit)
--
--
1 (8X) 2
AIMB-750
2 (PCI-X 64-bit)
4 (PCI 32-bit)
--
--
1 (4X) 2
AIMB-760
1 (PCI-E 1X)
5 (PCI 32-bit)
--
--
--
4
AIMB-762
1 (PCI-E 16X)
1 (PCI-E 4X)
5 (PCI 32-bit)
--
--
--
4
Table B.2: MicroATX Motherboard Options
Model Name
Bus
PCI
AGP
SATA
AIMB-560
3 (32-bit)
--
2
AIMB-554
1 (PCIe 16X)
1 (PCIe 4X)
--
4
IPC-7120 User Manual
32
Appendix
C
Safety Instructions
Appendix C Safety Instructions
C.1 English
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Read these safety instructions carefully.
Keep this installation reference guide for later reference.
Disconnect this equipment from any AC outlet before cleaning. Do
not use liquid or spray detergents for cleaning. Use a damp cloth.
For pluggable equipment, the power outlet must be installed near
the equipment and must be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage.
The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient over-voltage.
Never pour any liquid into an opening. This could cause fire or
electrical shock.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140°
F). THIS MAY DAMAGE THE EQUIPMENT.
Never open the equipment. For safety reasons, the equipment
should be opened only by qualified service personnel.
If any of the following situations arises, get the equipment checked
by service personnel:
a) The power cord or plug is damaged.
b) Liquid has penetrated into the equipment.
c) The equipment has been exposed to moisture.
d) The equipment does not work well, or you cannot get it to work
according to the installation reference guide.
e) The equipment has been dropped and damaged.
f) The equipment has obvious signs of breakage.
The sound pressure level at the operator's position according to IEC 7041:1982 is equal to or less than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.
IPC-7120 User Manual
34
C.2 German – Wichtige Sicherheishinweise
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Bitte lesen sie Sich diese Hinweise sorgfältig durch.
Heben Sie diese Anleitung für den späteren Gebrauch auf.
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient
ein angefeuchtetes Tuch zur Reinigung.
Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und
leicht zugänglich sein.
Das Gerät ist vor Feuchtigkeit zu schützen.
Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.
Ein Kippen oder Fallen könnte Verletzungen hervorrufen.
Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät
vor überhitzung schützt. Sorgen Sie dafür, daß diese Öffnungen
nicht abgedeckt werden.
Beachten Sie beim Anschluß an das Stromnetz die Anschlußwerte.
Verlegen Sie die Netzanschlußleitung so, daß niemand darüber
fallen kann. Es sollte auch nichts auf der Leitung abgestellt werden.
Alle Hinweise und Warnungen die sich am Geräten befinden sind
zu beachten.
Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten
Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.
Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder
Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw
elektrischen Schlag auslösen.
Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
Bitte lassen Sie das Gerät nicht unbehehrt hinten unter -20° C (-4°
F) oder oben 60° C (140° F), weil diesen Temperaturen das Gerät
zerstören könten.
Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz
zu trennen und von einer qualifizierten Servicestelle zu überprüfen:
a)
b)
c)
d)
Netzkabel oder Netzstecker sind beschädigt.
Flüssigkeit ist in das Gerät eingedrungen.
Das Gerät war Feuchtigkeit ausgesetzt.
Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
e) Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f) Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70 dB (A) oder weiger.
35
Appendix C
DISCLAIMER: This set of instructions is provided according to IEC7041. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
IPC-7120 User Manual
36