Craftsman 917.377150 Owner`s manual

Owner's Manual
CRAFTSMAN
°
60 HORSEPOWER
22 REAR DISCHARGE
POWER PROPELLED
ROTARY LAWN MOWER
Model No.
917.377150
•
•
•
•
•
•
Safety
Assembly
Operation
Maintenance
Espa_ol
Repair Parts
CAUTION:
Read and follow all
Safety Rules and Instructions
before operating this equipment
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Visit our Craftsman website: www sears corn/craftsman
Warranty
Safety Rules
Assembly
Operation
Maintenance
Schedule
Maintenance
LIMITED
2
2
4
6
10
10
TWO YEAR WARRANTY
Product Specifications
Service and Adjustments
Storage
Troubleshooting
Repair Parts
Parts Ordering
ON CRAFTSMAN
POWER
11
14
16
17
37
Back Cover
MOWER
For two years from date of purchase, when this Craftsman Lawn Mower is maintained,
lubricated, and tuned up according to the operating and maintenance
instructions in the
owner's manual, Sears will repair free of charge any defect in material or workmanship.
If this Craftsman Lawn Mower is used for commercial
or rental purposes, this warranty
applies for only 90 days from the date of purchase.
This Warranty does not cover:
• Expendable items which become worn during normal use, such as rotary mower
blades, blade adapters, belts, air cleaners and spark plug.
• Repairs necessary because of operator abuse or negligence,
Lncluding bent crankshafts and the failure to maintain the equipment according to the instructions contained in the owner's manual.
Warranty service is available by returning the Craftsman power mower to the nearest
Sears Service Center/Department
in the United States. This warranty applies only while
this product is in use in the United States.
This Warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
SEARS, ROEBUCKAND
CO., D/817 WA, HOFFMAN
ESTATES, ILLINOIS 60179
Safety standards require operator
presence controls to minimize the
risk of injury. Your unit is equipped
with such controls. Do not attempt to
defeat the function of the operator
presence controls under any
circumstances.
TRAINING:
* Do not operate mower if it has been
dropped or damaged in any manner.
Always have damage repaired before
using your mower.
• Do not use accessory attachments that
are not recommended
by the manufacturer. Use of such attachments may be
hazardous.
• Read this operator's
Become familiar with
know how to operate
properly. Learn how
mower.
• The blade turns when the engine is
running.
manual carefully.
the controls and
your mower
to quickly stop
• Do not allow children to use your mower.
Never allow adults to use mower without
proper instructions.
• Keep the area of operation clear of all
persons, especially small children and
pets.
• Use mower only as the manufacturer
intended and as described in this
manual.
PREPARATION:
• Always thoroughly check the area to be
mowed and clear it of all stones, sticks,
wires, bones, and other foreign objects,
These objects will be thrown by the
blade and can cause severe injury.
• Always wear safety glasses or eye
shields when starting and while using
your mower.
• Dress properly. Do not operate mower
when barefoot or wearing open sandals.
Wear only solid shoes with good traction
2
when mowing.
• Check fuel tank before starting engine.
Do not fill gas tank indoors, when the
engine is running or when the engine is
hot. Allow the engine to cool for several
minutes before filling the gas tank. Clean
off any spilled gasoline before starting
the engine.
• Always make wheel height adjustments
before starting your mower. Never
attempt to do this while the engine is
running.
• Mow only in daylight or good artificial
light.
• Never cut grass by pulling the mower
towards you. Mow across the face of
slopes, never up and down or you
might lose your footing. Do not mow
excessively steep slopes. Use caution
when operating the mower on uneven
terrain or when changing directions -maintain good footing.
• Never operate your mower without
proper guards, plates, grass catcher or
other safety devices in place.
MAINTENANCE
AND STORAGE:
• Check the blade and the engine
mounting bolts often to be sure they are
tightened properly.
• Check all bolts, nuts and screws at
OPERATION:
• Keep your eyes and mind on your
mower and the area being cut. Do not let
other interests distract you.
• Do not mow wet or slippery grass. Never
run while operating your mower. Always
be sure of your footing -- keep a firm
hold on the handles and walk.
frequent intervals for proper tightness to
be sure mower is in safe working
condition.
• Keep all safety devices in place and
working.
• To reduce fire hazard, keep the engine
free of grass, leaves or excessive
grease and oil.
• Check grass catcher often for deterioration and wear and replace worn bags.
Use only replacement bags that are
recommended
by and comply with
specifications of the manufacturer
of
your mower.
• Always keep a sharp blade on your
mower.
• Allow engine to cool before storing in
any enclosure.
• Never store mower with fuel in the tank
• Do not put hands or feet near or under
rotating pads. Keep clear of the discharge opening at all times.
• Always stop the engine whenever you
leave or are not using your mower, or
before crossing driveways, walks, roads,
and any gravel--covered
areas.
• Never direct discharge of material
toward bystanders nor allow anyone
near the mower while you are operating
it.
• Before cleaning, inspecting, or repairing
your mower, stop the engine and make
absolutely sure the blade and all moving
parts have stopped. Then disconnect the
spark plug wire and keep it away from
the spark plug to prevent accidental
starting.
• Do not continue to run your mower if you
hit a foreign object. Follow the procedure
outlined above, then repair any damage
before restarting and operating you
mower.
• Do not change the governor settings or
overspeed the engine. Engine damage
or personal injury may result.
• Do not operate your mower if it vibrates
abnormally. Excessive vibration is an
indication of damage; stop the engine,
safely check for the cause of vibration
and repair as required.
• Do not run the engine indoors. Exhaust
fumes are dangerous.
inside
reach
source
space
a building where fumes may
an open flame or an ignition
such as a hot water heater,
heater, clothes dryer, etc.
ALook for this symbol to point out
important safety precautions.
It means
CAUTION!!!
BECOMEALERTH!
YOUR
SAFETY IS INVOLVED.
_CAUTION:
A.Iways disconnect spark
plug wire and place wire where it cannot
contact spark plug in order to prevent
accidental starting when setting up,
transporting,
adjusting or making repairs.
_WARNING
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects,
or other reproductive
harm.
3
These accessories were available when this lawn mower was produced. They are not
shipped with your mower. They are also available at most Sears retail outlets and servP.e
centers. Most Sears stores can also order repair parts for you, when you provide the model
number of your lawn mower. Some of these accessories may not apply to your lawn mower.
LAWN MOWER PERFORMANCE
i
CUPPING DEFLECTOR
FOR REAR DISCHARGE LAWN MOWERS
GRASS CATCHERS
FOR
REAR DISCHARGE
LAWN MOWERS
MULCHERKFrS
STABILIZER
FOR
SIDE DISCHARGE
GRASS
LAWN CATCHERS
MOWERS
_!
GAS CANS
LAWN MOWER
MAINTENANCE
MUFFLERS
AIR RLTERS
SPARK PLUGS
:
BELTS
BLAOES
BLADE ADAPTERS
WHEELS
i
i
ENGINE OIL
TO REMOVELAWNMOWERFROM
CARTON
Read these instructions and this manual in its
entirety before you attempt to assemble or
operate your new lawn mower.
IMPORTANT: This lawn mower is shipped
WITHOUT OIL OR GASOLINE in the engine.
Your new lawn mower has been assembled
• Remove loose parts included with mower.
• Cut down two end comers of carton and
lay end panel down flat.
• Remove all packing materials except
padding between upper and lower handle
and padding holding operator presence
control bar to upper handle.
• Roll lawn mower out of carton and check
at the factory with the exception of those parts
left unassembled for shipping purposes. All
parts such as nuts, washers, bolts, etc.,
necessary to complete the assembly have
been placed in the parts beg. To ensure safe
and proper operation of your lawn mower, all
parts and hardware you asserrble must be
tightened securely. Use the correct tools as
necessary to ensure proper tightness.
carton thoroughly for additional loose
parts.
4
HOW TO SET UP YOUR LAWN MOWER
TO INSTALL ATrACHMENTS
TO UNFOLD HANDLE
Your lawn mower was shipped ready to be
used as a mulcher. To convert to bagging or
discharging:
• Open rear door and remove mulcher plug.
Store mulcher plug in a safe place.
• You can now install catcher or optional
clipping daflector.
• To return to mulching operation, install
mulcher plug into discharge opening of
mower. Be sure all tabs are seated
IMPORTANT: Unfold handles carefully so as
not to pinch or damage control cables.
• Raise handles until lower handle section
locks into place in mowing position.
• Remove protective padding, raise upper
handle section into place on lower handle
and tighten both handle knobs.
• Remove handle padding holding operator
presence control bar to upper handle.
• Your lawn mower handle can be adjusted
for your mowing comfort. Refer to "Adjuat
Handle" in the Service and Adjustment
section of this manual.
properly.
Operator presence contr,_
o,pe,
Mulcher ptu_
7
i
Lower'
)
position
ACAUTION:
Do not run your lawn
mower without mulcher plug in place or
approved clipping deflector or grass
catcher in place. Never attempt to
operate the lawn mower with the rear
door removed or propped open.
5
KNOW YOUR LAWN MOWER
READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR LAWN
MOWER. Compare the illustrationswith your lawn mower to familiarize yourself with the
I_?_|i?n of various controls and adiustments. Save this manual for future reference.
"llweesymbo_mayappearonyourlawnrnow_ orin literatura_Rdied w#htheproduct.
Lmm and_
th_ m_n_
CAUTION
ENGINE
OR WARNING
ON
ENGINE
OFF
FAST
SLOW
CHOKE
Engine zone control cable
FUEL
OIL
DANGER, KEEP HANDS
AND FEET AWAY
Operator presence control bar
Drive control lever
Throttle Control
Starter handle
Handle knob
Grass
Mulohar
Engine oil
w/
dipstick
plug
Housing
Drive cover
Gasoline cap
Primer
IMPORTANT: This lawn mower is shipped
WITHOUT OIL OR GASOLINE in the engine.
Wheel adjuster
(on each wheel)
MEETS CPSC SAFETY REQUIREMENTS
Sears rotary waJk-behind power lawn mowers conform to the safety standards of the American
National Standards Institute and the U.S. Consumer Product Safety Commission. The blade
turns when the engine is running.
Drive control lever - used to engage powerpropelled forward motion of lawn mower.
Mulcber plug - must be removed to convert to
bagging or discharging operation.
Throttle Control - used for starting the engine
and allows you to select either fast or slow
engine speed.
Operator presence control bar - must be
held down to the handle to start the engine.
Release to stop the engine,
Primer - pumps additional fuel from the
carburetor to the cylinder for use when
starting a cold engine.
Starter handle - used for starting the engine.
6
Plate Tab
mower
can result
in foreign
The
operation
of any
lawn
objects thrown into the eyes,
which can result in severe eye damage.
Always wear safety glasses or eye shields
while operating your lawn mower or
performing any adjustments or repairs.
We recommend a wide vision safety mask
over spectacles or standard safety
glasses,
HOW'tO USEYOUR LAWN MOWER
ENGINE SPEED
The engine speed is controlled by a
throttle located on the side of the upper
handle. Fast position is for starting,
normal cutting, trimming and better grass
bagging. Slow position is for light cutting,
Lower Wheels for High Cutr,.._L_.._
Raise Wheels for Low Cut
TO ATTACH
and place the grass catcher frame
hooks onto the door pivot pins.
• The grass catcher is secured to the
lawn mower housing when the rear
door is lowered onto the grass catcher
frame.
_CAUTION:
Do not run your lawn
mower without clipping deflector or
approved grass catcher in place. Never
attempt to operate the lawn mower with
the rear door removed or propped open.
trimming and fuel econo_my.
Fast
Slow
F-.
,,
.::,
i//
('
GRASS CATCHER
• Lift the rear door of the lawn mower
}_
,//
G rass
catcher
handle
ENGINE ZONE CONTROL
ACAUTION:
Federal regulations require
an engine control to be installed on this
lawn mower in order to minimize the risk
of blade contact injury.
circumstances attempt
function of the operator
turns when the engine
Pivot
pins
Do not under any
to defeat the
control. The blade
is running.
Catcher
frame hook
TO EMPTY GRASS CATCHER
• Lift up on grass catcher using the frame
handle.
• Your lawn mower is equipped with an
operator presence control bar which
requires the operator to be positioned
behind the lawn mower handle to start and
• Remove grass catcher with clippings
from under lawn mower handle.
• Empty clippings from bag using both
frame handle and bag handle,
NOTE:
Do not drag the bag when
emptying; it will cause unnecessary wear.
operate the lawn mower.
TO ADJUST CuI"rlNG HEIGHT
• Raise wheels for low cut and lower wheels
forh cut.
• Adjust cutting height to suit your requiremerits. Medium position is best for most
lawns.
• To change cutting height, squeeze adjuster
laver toward wheel Move wheel up or
down to suit your requirements. Be sure all
wheels are in the same setting.
NOTE: Adjuster is propedy positioned
when plate tab inserts into hole in lever.
Also, 9-position adjusters (if so equipped)
allow lever to be positioned between the
plate tabs.
Grass
Bag
handle
7
frame
handle
DRIVE CONTROL
ADD GASOUNE
• Self-propelling is controlled by holding
the operator presence control bar down
to the handle and pushing the drive
control lever forward until it clicks; then
release the lever.
NOTE: Before filling fuel tank, remove
and discard the debris plug that is inside
the tank.
• Forward motion will stop when the
operator presence control bar is
released. TO stop forward motion
without stopping engine, release the
operator presence control bar slightly
until the drive control disengages.
Hold
operator presence control bar down to
handle to continue mowing without selfpropelling.
• To keep drive control engaged when
turning corners, push down on handle
and lift front wheels off ground while
turning lawn mower.
Operator presence control bar
Ddve
cont_
• Fill fuel tank. Use fresh, clean, regular
unleaded gasoline with a minimum of 87
octane. Do not mix oil with gesoline.
Purchase fuel in o_
that can be
used wi0dn 30 days to assure fuel
freshness.
AWARNING:
_
indicates that
alcoholblendedluels (calledgasohoior
usingethanolor msthanol)canattract
moisture which leads to separation and
fon'netion of acids dunng storage. Acidic gas
can damage the fuel system of an engine
whilein storage.Toavoidengineproblems,
the fuel system should be emptied before
storage of 30 days or longer. D_n the gas
tank, start the engine and let it run unt# the
fuel lines and carburetor are erupt. Use
fresh fuel next season. See Storage
Instructions for _
information. Never
use engine or carburetor cleaner products in
the fuel tank or permanent damage may
occur.
To engage ddve
control
_I, CAUTION:
Fill to bottom of gas tank
filler neck. Do not overfill. Wipe off any
spilled oil or fuel. Do not store, spill or
use gasoline near an open flame.
Ddve control
disengaged
BEFORE STARTING ENGINE
OIL
Your lawn mower is shippedwithoutoil in the
engine.
• Be sure mower is level and area around oil
fluis dean.
• Removeer_neoilcap
and fillto the full
line.
NOTE: Allow oil to settle down into engine
for accurate dipstick reading.
• Engineholds 20 ozs. of oil. Fortype and
gradeof oil to use, see "ENGINE" in
Maintenance sectionof this manual.
• Pour oil slowly. Do not over fill.
• Check oil level before each use. Add oil if
needed. RII to full line.
• To read proper level, tighten engine oil cap
each time.
• Reinstall engine oil cap and tighten.
• Change the oil after every 25 hours of
operationor each season. You may nesd
to change the oil more often under dusty,
arty con61kx_
Gasoline filler cap
Engine oil cap
(Discard
debds plug
inside)
TO START ENGINE
• To start a cold engine, push pdmer threa
(3) _nes beforet_yingto sterLUseafirm
push.Thisstepis notusu_/necessary
when starlingan enginewhich has
already run for a few minutes.
• Move threttle control lever to fsst posttion.
• Hold operator presence control bar down
to the handle and pul starter handle
quickly. Do not allow starter rope to snap
back.
• To stopengine,releaseoperatorpresance
cc_'of
8
Ixu'_
NOTE: In cooler weather it may be
necessary to repeat priming steps. In
warmer weather over priming may cause
flooding and engine will not start. If you
do flood engine, wait a few minutes
before attempting to start and do not
repeat priming steps.
MOWING TIPS
• Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing effort
and to keep from overloading the engine
and leaving clumps of grass clippings. It
may also be necessary to reduce
ground speed and/or run the lawn
mower over the area a second time.
• For extremely heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
• For better grass bagging and most
cutting conditions, the engine speed
should be set in the fast position.
• When using a rear discharge lawn
mower in moist, heavy grass, clumps of
cut grass may not enter the grass
catcher. Reduce ground speed (pushing speed) and/or run the lawn mower
over the area a second time.
• if a trail of clippings is left on the right
side of a rear discharge mower, mow in
a clockwise direction with a small
overlap to collect the clippings on the
next pass.
• Pores in cloth grass catchers can
become filled with dirt and dust with use
and catchers will collect less grass. To
prevent this, regularly hose catcher off
with water and let dry before using.
• Keep top of engine around starter clear
and clean of grass clippings and chaff.
This will help engine air flow and extend
engine life.
MULCHING
MOWING TIPS
IMPORTANT: Forbest performance,keep
mower housingfree of built-upgrass and
trash.See =Cleanir_ in Maintenance section
of this manual.
• The specialmulchingbladewillrecutthe
grassclippingsmany timesand reduce
them in size so that as they fallontothe
lawnthey willdisperseintothe grassand
notbe noticed. Also,the mulchedgrasswill
biodegradequicHy to providenutrientsfor
the lawn. Always mulchwithyour highest
engine(blade) speed as thiswillprovidethe
best recuttingactionofthe blades.
• Avoidcuttingyour lawn when it is wet. Wet
grasstends to formclumpsand interferes
with the mulchingaction. The bsstlime to
mow your lawnis the eady afternoon. At
thistime the grass has driedand the newly
cut mea WIUnot be exposedto the direct
euR.
• For best results,adjustthe lawn mower
cuttingheightso thatthe lawn mower cuts
off onlythe topone-thirdof the grassblades.
ff the lawn is overgrownIt will be necsssary
to raisethe heightof cutto reducepushing
effortand to keep fromoverloadingthe
engine and leavingclumpsof mulched
grass.For e_
heavy mulching,
reduce yourwidthofcut by overlapping
previouslycutpath and mow slowly.
• Certaintypesof grass and grsssconditions
may requirethat an area be mulcheda
secondtimeto completelyhide the
clippings. Wben doinga secondcut, mow
_ross or _
to the firstcutpath.
• Change your cuttingpattem fromweek to
week. Mow norih to southone week then
changeto east to wP_-tthe nextweek. This
willhelppreventmattingand grainingof the
lawn.
9
REGUSE.WCE
.
SERVICE
DATES
Check for Loose Fasteners
Clean/Inspect Grass Catcher
l/
M
(if
Equipped)
Clean
Lawn Mower
i_1
O
(Power-Propel!ed
Clean
Under DriveMowersI
Cover
Check drive belt/pulleys
E
(Powar-PropalledMowars)
Check/Sherpen/Replace Blade
LubricationChart
!
_
_
v'
v'
v
Clean Battery/RecharQa
Electric Start Mowers_
v'
i1 Check Engine Oil Level
N Change Engine Oil
!G Clean Air Filter
v',
V'_,=
_1 Clean
InspectMuffler
or Replace Spark Plug
E Replece
AirFilterPaperCarlridge
12 34 -
1_2
Change more often when operating under a heaW lOad 0€In high amblen! temperatures.
SaUce more often when oflera_g in d_rtyor dusly condlUo_s.
Replace blades more often when mowing in sandy soil,
Charge 48 hours at end of season.
GENERALRECOMMENDATIONS
LUBRICATION
The warranty on this lawn mower does not
cover items that have been subjected to
operator abuse or negligence. To receive
full value from the warranty, operator must
maintain mower as instructed in this
manual.
CHART
Wheela_uster
Some adjustments will need to be made
periodically to property maintain your unit.
All adjustments in the Service and
Adjustments section of this manual should
be checked at least once each season.
• Once a year, replace the spark plug,
replace air filter element and check
blade for wear. A new spark plug and
clean/new air filter element assures
Rear door hinge
proper air-fuel mixture and helps your
engine run better and last longer.
• Follow the maintenance schedule in this
manual.
BEFORE EACH USE
(_) Handle bracket mounting pin
(_ Spray lubricant
(_) Referto Maintenance "ENGINE" section.
• Check engine oil level.
• Check for loose fasteners,
LUBRICATION
IMPORTANT: Do not oil or grease plastic
wheel bearings. VL,.,.,.,.,.,.,.,.,_ous
lubricants will attract
dust and dirt that will shorten the life of the serf
Keep unit well lubricated (See "LUBRICATION CHART").
lubricating bearings. If you feet they must be
lubricated, use only a dry, powdered graphite
typelub ,a , aringly.
10
PRODUCT
SPECIFICATIONS
SERIALNUMBER
DATE OF PURCHASE
GASOLINE
CAPACITY/TYPE:
1.6 QUARTS
UNLEADED
OIL TYPE (API-SF/SG/SH):
SAE 30 (ABOVE 32°F)
SAE 5W-30 IBELOW 32°F)
20 OZS.
OIL CAPACITY:
SPARK PLUG IGAP:
VALVE CLEARANCE:
REGULAR
CHAMPION
.030" I
INTAKE:
EXHAUST:
RJ19LM
.004 - .008
.004 - .008
SOLID STATE IGNITION
AIR GAP:
.0125
BLADE BOLT TORQUE:
35-40 FT. LBS.
IN.
• The model and serial numbers will be found on a decal attached
lawn mower housing.Record
provided above.
to the rear of the
both serial number and date of purchase
LAWN MOWER
OR J19LM
in space
NOTE: Remove the blade adapter and
check the key inside hub of blade adapter.
The key must be in good condition to work
properly. Replace adapter if damaged.
Always observe safety rules when performing
any maintenance.
TIRES
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
• Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may cause
tire damage.
BLADE CARE
TO REPLACE
BLADE
• Position the blade adapter on the
engine crankshaft.
Be sure key in
adapter and crankshaft keyway are
aligned.
• Position blade on the blade adapter
aligning the two (2) holes in the blade
with the raised lugs on the adapter.
• Be sure the trailing edge of blade
(opposite sharp edge) is up toward the
engine.
• Install the blade bolt with the lock
washer and hardened washer into
blade adapter and crankshaft.
• Use block of wood between blade and
For best results, mower blade must be
kept sharp.
Replace bent or damaged
blades.
TO REMOVE BLADE
• Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
• Tum lawn mower on its side. Make
sure air filter and carburetor are up.
• Use a wood block between blade and
mower housing to prevent blade from
tuming when removing blade bolt.
• Protect your hands with gloves and/or
wrap blade with heavy cloth.
• Remove blade bolt by tuming counter°
clockwise.
• Remove blade and attaching hardware
(bolt, lock washer and hardened
washer).
lawn mower housing and tighten the
blade bolt, turning clockwise.
• The recommended tightening torque is
35-40 ft. Ibs.
11
IMPORTANT:
treated.
Blade bolt is grade 8 heat
TO SHARPEN
BLADE
NOTE: We do not recommend sharpening blade - but if you do, be sure the blade
is balanced.
Cam should be taken to keep the blade
balanced. An unbalanced blade will
cause eventual damage to lawn mower or
engine.
• The blade can be sharpened with a file
or on a grinding wheel. Do not attempt
to sharpen while on the mower.
• To check blade balance, drive a nail
into a beam or wall. Leave about one
inch of the straight nail exposed. Place
center hole of blade over the head of
the nail. If blade is balanced, it should
remain in a horizontal position. If either
end of the blade moves downward,
sharpen the heavy end until the blade
is balanced.
Crank shaft
Blade
keyway
• To keep your drive system working
propedy, the gear case and area
around the drive should be kept clean
and free of trash build-up. Clean under
the drive cover twice a season.
• The gear case is filled with lubdcant to
the proper level at the factory. The only
time the lubricant needs attention is if
service has been performed on the
gear case.
• If lubricant is required, use only Texaco
Starplex Premium 1 Grease, Part No.
750369.
Do not substitute.
ENGINE
LUBRICATION
Use only high quality detergent oil rated
with API service classification SF, SG or
Key
Blade
SH. Select the oil's SAE viscosity grade
according to your expected operating
temperature.
Crank
shaft
bolt
Lock
washer Hardened
washer
• Remove any trash or grass cuttings
from inside the dust cover, pinion and/
or drive wheel gear teeth.
• Put wheels back in place.
• If after cleaning, the drive wheels do
not turn freely, contact your nearest
authorized service center.
GEAR CASE
edge
Blade
adapter
GRASS CATCHER
• The grass catchermay be hossdwith
water, but must be dry when used.
• Check your grasscatcher oftenfor
damage or deterioration. Through normal
use itwillwear. If catcherneeds replacing,
replaceonly with a manufacturerapproved
replacementcatcher. Give the lawn
mower model number when ordering.
•20"
0"
Jo"
-20"
TEMPERATURE RAN_
0"
10"
20"
30"
ANTICJ pATED BEFORE NEXT OIL CHANGE
NOTE: Although multi-viscosity
oils
(5W30, 10W30 etc.) improve starting in
cold weather, these multi-viscosity
oils
will result in increased oil consumption
when used above 32°F. Check your
engine oil level more frequently to avoid
possible engine damage from running
tow on oil.
DRIVE WHEELS
Check front drive wheels each time before
you mow to be sure they move freely.
The wheels not turning freely means
trash, grass cuttings, etc. are in the drive
wheel area and must be cleaned to free
drive wheels.
If necessary to clean the drive wheels,
check both front wheels.
• Remove hubcaps, hairpin cotters and
washers.
• Remove wheels from wheel adjusters. 12
Change the oil after every 25 hours of
operation or at least once a year if the
lawn mower is not used for 25 hours in
one year,
Check the crankcase oil level before
starting the engine and after each five (5)
hours of continuous use. "13ghtan oil plug
securely each time you check the oil
level.
TO CHANGEENGINEOIL
NOTE: Beforetipping lawn mowerto
drain oil, drain fuel tank by running
engine until fuel tank is empty.
• Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
• Remove engine oil cap; lay aside on a
clean surface.
• Tip lawn mower on its side as shown
and drain oil into a suitable container.
Rock lawn mower back and forth to
remove any oil trapped inside of
engine.
• Wipe off any spilled oil on lawn mower
and on side of engine.
• Fill engine with oil. Fill only to the
"FULL" line on the dipstick. DO NOT
overfill.
• Replace engine oil cap.
• Reconnect spark plug wire to spark
plug.
Container
AIR FILTER
Your engine will not run prepedy and may
be damaged by using a dirty air filter.
Replace the air filter eve_J year, more
often if you mow in very dusty, dirty
conditions.
TO CLEAN AIR FILTER
• Loosen screw and tilt cover to remove.
• Carefully remove cartridge.
• Clean by gently tapping on a flat
surface. If very dirty, replace cadddge.
&CAUTION:
Petroleum solvents, such
as kerosene, are not to be used to clean
cartridge. They may cause deterioration
of the cartridge. Do not oil cartridge. Do
not use pressurized air to clean or dry
cartridge.
• Install cartridge, then replace cover
making sure the tabs are aligned with
the slots in the back plate. Fasten
screw securely.
Cover
tabs
Back
plate
Slots
Cover
Ca_dge
MUFFLER
Inspect and replace corroded muffler as
it could create a fire hazard and/or
damage.
SPARK PLUG
Change your spark plug each year to
make your engine start easier and run
better. Set spark plug gap at .030 inch.
CLEANING
IMPORTANT: For best performance,
keep mower housing free of built-up
grass and trash. Clean the underside of
your mower after each use.
&CAUTION:
Disconnect spark plug wire
from spark plug and place wire where it
cannot come in contact with the spark
plug.
• Turn lawn mower on its side. Make
sure air filter and carburetor are up.
Clean the underside of your lawn
mower by scraping to remove build-up
of grass and trash.
• Clean engine often to keep trash from
accumulating. A clogged engine runs
hotter and shortens engine life.
• Keep finished surfaces and wheels
free of all gasoline, oil,etc.
• We do not recommend using a garden
hose to clean lawn mower unless the
electrical system, muffler, air filter and
carburetor are covered to keep water
out. Water in engine can result in
shortened engine life.
CLEAN UNDER DRIVE COVER
Clean under drive cover at least twice a
season. Scrape underside of cover with
putty knife or similar tool to remove any
build-up of trash or grass on underside
of ddve cover.
13
_kCAUTION:
Before performing any
service and adjustments:
•
•
Release control bar and stop engine.
Make sure the blade and all moving
parts have completely stopped.
•
Disconnect spark plug wire from spark
plug and place where it cannot come
in contact with plug.
LAWN MOWER
TO ADJUST CUTFING HEIGHT
See '9"0 ADJUST CU'I-rlNG HEIGHT" in the
Operation section of this manual.
REAR DEFLECTOR
The rear deflector, attached between the rear
wheels of your lawn mower, is provided to
minimize the possibility that objects will be
thrown out the rear of the lawn mower into the
operator's mowing position. If the rear
deflector becomesdamaged,
it should be
TO ADJUST HANDLE
The handle can be mounted in a high or
low position. The mounting holes in the
bottom of lower handle are off center for
raising or lowering the handle.
• Remove upper handle and all parts
attached to lower handle.
• Remove hairpin cotters from lower
handle bracket mounting pin.
• Squeeze lower handle in to remove it
from mounting pins.
• Turn lower handle over to raise or lower
handle.
• Squeeze lower handle in and position
holes onto mounting pins on handle
bracket.
• Reassemble upper handle and all parts
removed from lower handle.
Mowing
position
replaced.
TO REMOVE/REPLACE
DRIVE BELT
• Remove drive cover. Remove belt by
pushing down on gear case pulley and roll
belt off.
• Turn lawn mower on its side with carbur_
tor and fuel cap up.
• Remove blade.
• Remove debris shield.
.,
,(-_
I
Low position
• Installnewbeltby reversing
abovestep6.
• Always use factory approved belt to assure
life.
O.ve
NbIllk\
Mowing
position
I
.; l
• Remove belt from engine pulley on
crankshaft.
f_and_
_,
h-_
V
Belt _
14
High position
TO ASSEMBLE
GRASS
ENGINE SPEED
CATCHER
• Put grass catcher frame into grass bag
with rigid part of bag on the bottom.
Make sure the frame handle is outside
of the bag top.
• Slip vinyl bindings over frame.
NOTE: If vinyl bindings are too stiff, hold
them in warm water for a few minutes. If
bag gets wet, let it dry before using.
_CAUTION:
Do not run your lawn mower
without clipping deflector or approved
grass catcher in place. Never attempt to
operate the lawn mower with the rear
door removed or propped open.
frame
_"'_///
_
I
_'_
_\\
Your engine speed has been factory set.
Do not attempt to increase engine speed
or it may result in personal injury. If you
believe that the engine is running too fast
or too slow, take your lawn mower to an
authorized service center for repair and
adjustment.
CARBURETOR
Your carburetor has a non-adjustable
fixed main jet for mixture control. If your
engine does not operate properly due to
suspected carburetor problems, take your
lawn mower to an authorized service
center for repair and/or adjustment.
IMPORTANT: never tamper with the
engine governor, which is factory set for
proper engine speed. Overspeeding the
engine above the factory high speed
setting can be dangerous, if you think the
engine-governed high speed needs
adjusting, contact your nearest authorzed
service center, which has proper
equipment and experience to make any
necessary adjustments.
Frame
opening
15
Immediately prepare your lawn mower for
storage at the end of the season or if the unit
will not be used for 30 days or more.
Operator presence control bar
Fold foward
for storage
LAWNMOWER
When lawn mower is to be stored for a period
of time, clean if thoroughly, remove all dirt,
grease, leaves, etc. Store in a dean, dry area.
• Clean entire lawn mower (See "CLEAN|NG" in the Maintenance section of this
manual).
• Lubricate as shown in the Maintenance
section of this manual.
• Be sure that all nuts, bolts, screws, and pins
are securely fastened. Inspect moving
parts for damage, breakage and wear.
Replaceif necessary.
• Touch up all rusted or chipped paint
surfaces; sand lightly before painting.
HANDLE
You can fold your lawn mower handle for
storage.
• Squeeze the bottom ands of the lower
handle toward each other until the lower
handle dears the handle bracket, then
move handle forward.
• Loosen upper handle mounting belts
enough to allow upper handle to be folded
back.
IMPORTANT." When folding the handle for
storage or transportation, be sure to fold the
handle as shown or you any dan_ge the
control cables.
• When setting up your handle from the
storage position, the lower handle will
automatically lock into the mowing position.
Lower
Handle
bracket
Squeeze to fold
Upper
Fold
backward
Lower
handle
Mowing
position
ENGINE
FUELSYSTEM
IMPORTANT: it is important to prevent gum
deposits from forming in essential fuel system
parts such as carburetor, f fuel filter, fuel hose
or tank during storage. Also, e_perience
indicates that alcohol blended fueis( called
gasohol or using ethanol or methanol) can
attract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine
while in storage.
• Drain the fuel tank.
• Start the engine and let it run un_l the fuel
lines and carburetor are empty.
• Never use engine or carburetor cleaner
products in the fuel tank or permanent
damage may occur.
• Use fresh fuelnextseason.
NOTE: Fuel stabilizer is an acceptable
alternatNe in minimizing the formation of fuel
gum deposits during storage. Add stabilizer
to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer
container. Run engine at least 10 minutes
after adding stabilizer to allow the stabilizer to
reach the carburetor. Do not drain the gas
tank and cad0uretor if using fuel stabilizer.
Hairpin
cotter
16
ENGINEOIL
Drain oil (with engine warm) and replace with
clean engine oil. (See "ENGINE" in the
Maintenance section of this manual).
CYUNDER
• Remove spark plug.
• Pour one ounce (29 ml) of oil through spark
plug hole into cylinder.
• Pull starter handle slowly a few times to
distribute oil.
• Replace with new spark plug.
OTHER
• Do not store gasoline from one season to
another.
• Replace your gasoline can if your can
stads to rusL Rust and/or dlrt in your
TROUBLESHOOTING
CHART
PROBLEM
Does not start
gasolinewill cause problems.
• If possible,store your unit indoorsand
cover it to give protectionfrom dustand dirt.
• Cover your unitwith a suitableprotective
coverthat does not retainmoisture. Do
not use pl_tic. Plasticcannotbreathe
which allows condensationto form and will
cause your unitto rust.
IMPORTANT: Never cover mowerwhile
engine and exhaust areas are stillwarm.
ACAUTION:
Never store the lawn
mower with gasoline in the tank inside a
building where fumes may reach an open
flame or spark. Allow the engine to cool
before storing in any enclosure.
CAUSE
1.
2.
3.
Dirtyairfilter.
Out offuai.
Stale fuel.
4.
Water in fuel.
CORRECTION
1. Clean/replace air filter.
2. Rll fuel tank.
3. Drein tank and refiltwith
fresh clean fuel.
4. Drain fuel tank and
cadouretorand refilltank
w_hfresh
gaso_.
5. Sp=kp_gw_ _
5.
Connestwire to plug.
disconnected.
6. Redace
spark
p_
6. Sadeparkp_g.
7.
8.
9.
_Lossof power
1.
Loose blade or Ixokan blade 7. T_hten blade bolt or
rep_ceUadeadapt.
adapter.
Controlbar in released
8. Dopresscont_barto
handle,
Controlbar defective.
9. Rep_ce
contrd
bar.
Rear of lawn mower housing 1.
or cuttingblade dragging
in heavy grass.
Set to "Higher Cur'
po_on.
2. cuuinotoomuchgrass.
2. Setto'H'_jher
Cut"
3.
4.
3.
4.
Clean/re_
air filter.
Clean undemideof rnower
5.
6.
Check oil level,
Cut at slower waiking
po_on.
Dirtyairfilter.
Buildupof grass, leaves,
and trash under mower.
5. Too much oil in engine.
6. W_l_ng speed too fasL
h_
speed.
17
TROUBLESHOOTING
PROBLEM
Poor cut- uneven
Excessive
vibration
Starter rope hard
to pull
CHART
CAUSE
CORRECTION
1.
Wom, bent or loose blade.
I.
2.
Wheel heights uneven.
2.
Replace blade. "13ghten
blade bolt.
Set all wheeis at same
3.
Low engine speed
3.
height
Contact an authorized center/
4.
Buildup of grass, leaves
and trash under mower.
4.
department
Clean underside of
1,
Wom, bent or looseblade.
1.
2.
Bent engine cranksh_.
2.
1.
Engine flywheel brake is on 1.
when control bar is released.
2.
Bent engine crankshaft.
2.
3.
4.
Blade adapter broken.
Blade dragging in grass.
3.
4.
mower housing.
Replace blade. 13ghten
blade bolt.
Contact an authorized
servicecenter.
Depress control bar to
upper handle before
pulling starter rope.
Contact an authorized
service center.
Replace blade adapter.
Move lawn mower to cut
grass or to hard surface.
Loss of drive
1.
2.
Drive wheels not tuming
with drive control engaged.
Belt not drMng
1.
2.
Adjust or replace drive control
cable.
Put belt on pulleys or
replace
Grass catcher
not filling (if so
1.
2.
Cutting height too low.
Lift on blade wom off.
equipped)
3.
Catcher not venting air.
4.
Low engine speed
1.
2,
3.
4.
broken.
Raise cutting height.
Replace blade.
Clean grass catcher,
Set engine speed control in fast
pos on
Hard to push
1.
2.
Grass is too high or wheel
height is too low.
Rear of lawn mower
3.
housing or blade dragging
in grass.
Grass catcher too full.
4.
Handle height position not
_Jht for youo
18
1.
Raise cutting height.
2.
Raise rear of lawn mower
housing one (1) setting
higher.
3.
4.
Empty grass catcher.
Adjust handle height to
suit.
36
ROTARY LAWN MOWER -- MODEL NO. 917.377150
GEAR CASE ASSEMBLY PART NUMBER 702511
IT
1
i
KEY
NO.
PART
NO.
17490416
2
3
4
6
137055X(X)4
137053
57072
48373
7
8
77881
137051
KEY
NO.
DESCRIPTION
Tapping Screw 1/4-20 x
1-1/4
Engagement Bracket
Shifter
Seal
Gear Case Halves Kit
(Includes Key Nos. 4,
and 7)
Beadng
Worm Shaft
9
10
11
12
13
14
15
16
17
18
19
PART
NO.
137074
57079
131484
700343
86447
137050
750436X
750369
12000003
850848
81585X004
NOTE: All component dimensions given
in U.S. inches. 1 inch = 25.4 mm
37
DESCRIPTION
Ddve Shaft
HardenedWasher
Clutch Yoke
Bushing
Ping
HellcalGesr
Clutch Jaw
Grease
E-FUng
Hi-ProKey
Spdng Bracket
ROTARY
LAWN MOWER
MODEL NUMBER
917.377150
13
74
35
67
-4
35
315
67
25
41
ROTARY LAWN MOWER MODEL NUMBER 917.377150
KEY
NO.
1
2
4
5
6
8
9
10
11
12
13
14
15
16
17
18
20
22
23
25
27
28
29
30
31
32
34
35
37
39
40
41
44
46
47
PART
NO.
165452X479
130861
150425
66426
136376
145793
170947
128415
150050
STD512505
151440
156374X479
700365X479
133190X479
140661X479
63601
14O54O
84596
87677
83923
151138
142748
61651
750913X004
161961
170136X004
14663O
700325X007
150078
173571X479
173572X479
150406
172835
851514
141114
DESCRIPTION
Upper Handle
EngineZone ControlCable
MulcherPlug
Wire Tie
HandleKnob
ControlBar
Rear Door Kit
Pop Rivet
Self Tapping Screw #10-24 x 5/8
Hex Tapping Screw w/Seres 1/4-20 x 1/2
Hubcap
Back Plate
Side Baffle
Discharge Baffle
Rear Baffle
Keps Locknut 1/4-20
Rear Skirt
Engine Pulley
Hi-Pro Key #505
Hex Flange Nut
Wheel
Shoulder Bolt 3/8-16 x 1
Ballevilla Washer
Axle Arm Assembly
Selector Knob
Selector Spnng
Spacer
Wheel AdjustingBracket
Thread Cutting Screw w/Sems 5/16-18 x 3/4
Handle BracketAssembly (Left)
Handle BracketAssembly (Right)
Hex Head Thread Rolling Screw 3/8-16 x 1-1/8
Lawn Mower Housing (Incl. Key #14, 15, 51 &
Blade Adapter
Blade 22*
KEY
NO.
PART
NO.
48
49
50
51
52
55
56
57
58
59
61
851074
850263
851084
170031
85463
751582
88652
51793
157081X479
131959
132001
134612
64
......
65
66
67
68
-69
70
71
72
73
74
75
76
--
74760612
751592
88348
57143
161058
17600406
170938
170939
165912
700417
144929
111190X
83816
170962
DESCRIPTION
HardenedWasher
Helical Washer 3/8-24 x 1-3/8 Gr. 8
Hex Head Machine Screw 3/8-24 x 1-3/8 Gr. 8
Front Baffle Kit
Danger Decal
Locknut 3/8-16
Hinge Screw 1/4-20 x 1-1/4
HairpinCotter
LowerHandle
HandleBolt
RopeGuide
DebitsShield
Engine- (See Breakdown)
Bdggsl 2H802-2682-B1
Bolt
Nut
Washer
Wave Washer
Warning Decal (Not Shown)
Screw
Spnng LH
SpringRH
Bolt
Throttle
Screw
Clamp
Screw
Owner'sManual (EnglisWSpanish)
Available accessories notincluded with lawn mower:
.71 33303
Clipping Deflector
- 71 33623
Gas Can (2.5 gal.)
..
7133500
FuelStabUizer
.7133300
SAE 30W Oil (20 oz.)
.71 33417
Dust Shield
-7133316
MowerCover
ROTARY
LAWN MOWER MODEL NUMBER
917.377150
5
18
I
14
16
,\
•
\
13
\\
15
14
41
13
12
ROTARY LAWN MOWER MODEL NUMBER
KEY
NO.
1
3
4
5
6
8
9
11
12
13
14
15
16
18
PART
NO.
145755
751152
158755
146527
150495
150182
145212
150340
12000058
137054
88060
88118
67725
701037
DESCRIPTION
ControlCable Assembly
Locknut#10-24
Pan Head Machine Screw 1/4 x 2.12
V-Befl
SpringRetainer
Hubcap
FlangedNut
Wheel & Tire Assembly
E-Ring
l_nion
Dust Cover
FeltWasher
Washer I/2 x 1-I/2 x .134
SelectorKnob
KEY
NO.
26
28
31
PART
NO.
917.377150
DESCRIPTION
35
36
143603
154990
132010
137052
151521
702511
Pan Hasd Tapping Screw #10-24
DdveCover
Hex Flange Nut
Drive Pulley
Wheel AdjusterAssembly (Left)
Gear Case Assembly Kit
38
40
41
54
55
57
63601
75192
151520
169932
86012
169931
Locknut
Spring
Wheel AdjusterAssembly (Right)
Grasabag Assembly
Drivashaft Cover
Frame
37 13709o
sp_g
BRIGGS & STRATTON
4-CYCLE ENGINE
MODEL NO. 12H802
TYPE NO. 2682-B1
( 1019 LABEL KIT I
50
54 T
525
983 _
635
S
II1|
1095 VALVE OVERHAUL
GASKET SET
46
_r REQUIRES SPEClALTOOLS
TO INSTALL SEE REPAIR
INSTRUCTION MANUAL.
I 1058 OWNER'S MANUAL
I
42
BRIGGS & STRATTON
4-CYCLE ENGINE
MODEL NO. 12H802
TYPE NO. 2682-B1
188
968
967
613
f
708 Q
137
11oQ
127 _'_
617
43
J
110
bl-tl_
& ,_TI_A'II"ON
4-CYCLE ENGINE
l
MODEL NO. 12H802
TYPE NO. 2682-B1
/
304
I
60
689A
[
1036 LABEL KIT-EMISSION
597 _
44
BRIGGS & STRATrON
4-CYCLE ENGINE
MODEL NO. 12H802
TYPE NO. 2682-B1
615
4o4_
_
n
616
505 _
258
474
910
789
358 GASKET SET
3_
20_
177_
163 _
45
1087_
BRIGGS & STRATTON
4-CYCLE ENGINE
KEY
NO.
1
2
3
4
5
7
8
9
t0
11
12
13
15
16
20
22
23
24
25
26
27
28
29
32
33
34
35
40
43
45
46
50
51
53
54
PART
NO.
MODEL NO. 12H802
TYPE NO. 2682-B1
DESCRIPTION
493260
Cylind6r Assembly
293708
Bushing/Seal Kit
299819 _
Oil Seal
493279
Engine Sump
691160
Cylinder Head
272916 -_+ Cylinder Head Gasket
495786
Breather Assembly
272481 _+ Breather Gasket
94650
Screw (Breather Assembly)
231933
Breather Tube
272199
_
Crankcase Gasket
94547
Screw (Cylinder Head)
691680
Oil Drain Plug
498568
Crankshaft
399781
_r Oil Seal
691092
Screw (Engine Sump)
492177
Flywheel
222698
Flywheel Kay
499429
Piston Assembly (Standard)
499430
Piston Ass,/. (.010" O.S.)
499431
Piston Assy. (.020" O.S.)
499432
Piston Assy. (.030" O.S.)
499425
Ring Set (Standard)
499426
Ring Set (.010" O.S.)
499427
Ring Set (.020" O.S.)
499426
Ring Set (.030" O.S.)
263190
Piston Pin Lock
499423
Piston Pin
499424
Connecting Rod
94699
Screw (Connecting Rod)
262651
Exhaust Valve
262652
Intake Valve
691270
Valve Spdng
93312
Valve Retainer
493737
Governor/Oil Slinger
690548
Valve Tappet
691449
Cam Gear
497465
Intake Manifold
272199
,A- Intake Gasket
692524
Screw (Carburetor)
94526
Screw (intake Manifold)
KEY
NO.
55
56
57
58
PART
NO.
DESCRIPTION
Rewind Starter Housing
Starter Pulley
Rewind Starter Spdng
Starter Rope
(=Cutto Required Length)
60
281434
Starter Rope Grip
65A 94904
Screw (Rewind Starter
Housing)
81
223664
Muffler Screw Lock
95
94098
Screw (ThrottleValve)
493267
Throttle Shaft
97
104 231371 •
Float Hinge Pin
110 -----• •Washer (Sold in Kit Only)
117 494870
Main Jet
121 498260
Carburetor Kit
125 498170
Carburetor
127 -----• Welch Plug (Sold in Kit Only)
t30
224908
Throttle Valve
133
134
137
146
159
163
177
t87
188
190
202
209
222
227
258
287
300
304
305
306
691421
498144
498144
281464
398187
398188
Carburetor Float
•
Needle Valve (includes Seat)
• • Float Bowl Gasket
(Sold in Kit Only)
94388
Timing Key
224815
Support Bracket
272653_r••Air
Cleaner Gasket
280393
_ O-Ring Seat
492790
Fuel Line
693399
Screw (Control Bracket)
94511
Screw (Fuel Tank)
262579
Mechanical Governor Link
263044
Govemor Spring
497203
Control Bracket
690783
Governor Lever
94512
Screw (Brake)
94511
Screw (Oil Fill Tube)
497838
Exhaust Muffler
493293
Blower Housing
691108
Screw (BlowerHousing)
690450
Cylinder Shield
RPM Settings:
•
•
÷
Low Speed: 1900-2100
High Speed: 3000-3200
Included in Gasket Set, Ref Number 358.
Included in Carburetor Kit, Rat Number
121.
Included in Carburetor Gasket Sot, Ref
Number 977.
Inocluded in Value Overhaul Kit, Ref
Number 1095.
NOTE: All componentdimensionsgiven in U.S.
inches 1 inch= 25.4 mm
46
BRIGGS & STRATTON
4-CYCLE ENGINE
KEY
NO.
307
332
333
334
337
356
358
363
383
404
423
425
443
445
455
456
459
474
505
523
525
529
556
562
584
585
592
597
601
608
613
615
616
617
618
621
635
668
PART
NO.
690345
94877
802574
94731
802592
497833
497316
19069
89838
690272
93758
94872
94873
691219
225121
281503
281505
492841
231082
495264
495265
281299
94512
92613
692342
272238
94908
94943
93053
497680
94231
690340
691306
270344
262749
396847
66538
493823
MODEL NO. 12H802
TYPE NO. 2682-B1
DESCRIPTION
Screw (Cylinder Shield)
Nut (Flywheel)
Magneto Armature
Screw (Magneto Armature)
Spark Plug
Stop Wire
Gasket Set
Flywheel Puller
Spark Plug Wrench
Washer (Governor Crank)
Screw (Intedock Switch)
Screw (Air Cleaner Cover)
Screw (NC Primer Base)
NC Cartndge Filter
Flywheel Cup
Pawl Fdction Plate
Ratchet Pawl
Alternator
Nut (Governor Lever)
Dipstick
Oil Fill Tube
Grommet
Screw (Alternator)
Bolt (Governor Lever)
Breather Passage Cover
¢r Breather Passage Gasket
Nut (Rewind Starter Housing)
Screw (Pawl Friction Plate)
Fuel Line Clamp
Rewind Starter
Screw (Exhaust Muffler)
Retainer
Governor Crank
e<l. Intake Manifold Seal
Spring
Stop Switch
Spark Plug Boot
Spacer (Includes 2)
KEY
NO,
670
687
PART
NO.
DESCRIPTION
280512
94515
Fuel Tank Spacer
Screw
_Breatber Passage Cover)
689A 263073
Fdction Spring
708 691321 e.Throttle Shaft Seal
Timing Gear
741 262598
789 493380
Wiring Harness
Dipstick/TubeAssembly
847 495263
Cable Terminal
851 493880
Valve Seat (Intake)
869 691155
Valve Seat (Exhaust)
870 690380
Guide Bushing (Intake Valve )
871 63709
Guide Bushing
262001
(Exhaust Valve )
Stud (Alternator)
910 94510
921 497233
Blower Housing Cover
922 262640
Brake Spring
Brake
923 691994
Interlock Switch
935
398758
Fuel Tank Cap
957 397974
A/C Primer Base
966 496116
Pre Cleaner Filter
967 493537
Air Cleaner Cover
968 281340
Screw (Blower HousingCover)
969 94696
Screw (Support Bracket)
970 94749
Fuel Tank
972 495224
Float Bowl
975 493640
Carburetor Primer
976 496115
Carburetor Gasket Set
977 498261
Label Kit
1019
494256
Label Kit-Emission
1036
695111
Owner's Manual
1058
273693
Screw/Washer Kit
1059
398540
1087
280966
O-Ring Seal
Valve Overhaul Gasket Set
1095
498528
Guide Pilot
1102
232153
12J802-1915-E1Replacement Engine
--RPM Settings:
-/_
•
<_
+
Low Speed: 1900-2100
High Speed: 3000-3200
Included in Gasket Set, Ref Number 358.
Included in Carburetor Kit, Ref Number
121.
Included in Carburetor Gasket Set, Ref
Number 977.
Inccludedin Value Overhaul Kit, Ref
Number 1095.
NOTE: All componentdimensionsgiven in U.S.
inches 1 inch = 25.4 mm
47
Forrepair of majorbrand appliancesIn your own home...
no _
who made i_ no _
who sold _I
1-8 00-4-MY-HOME sMp,
v_ _jorrJg_
(1-8004694663)
www._mm.com
To bringin productssuchasvacuums,lawnequipmentand electronics
for repair,call for the location of your nearest Sears Parle & Repair Center
1-800-488-1222
A_._ _or_j_
wwwJlearl.coln
Fortile replacementparts,accessories
and owner's manuals
that you need to do-it-yOuFoelf,
callSears PartsDlrectS"l
1-800-366"PART
(1-800-366-7278)
6a.m.-11p._CST.
7daysaweek
wwwJNmm,eom Ipartldlmct
To pun::haseor inquire al:x:u:a SearsServk:eAgreemer;t:
1-800-827-6655
7 a.m,- 5 p.m.csr, Mon.- Sat.
Pa-apedrsa'vk_de_
a dorn_io,
y paraordenarpiezasconeWlEjaa domidio:
1-S88.SU-HOGI_"
huCanada
pourserviceenfrari_s:
1-877-LE-FOYER ='
(1"877-533"6937)
(1-888-784-6427)
SEARS
HomeCentrar"
O Sears, Roebuck and Co.
170982
01.03.00
O RegisteredTredernark1 ! TrMentm_ of Blink _
lindCo.
@ M.a_a Regkdnldl I _ Marca de Fiibdcede 8ears, Roebucklind Co.
VB
Printed in U.S.A.