Marantec Comfort 160 Operating instructions

GB
Operating instructions
Last updated: 07.2012
Operator systems for garage doors
Comfort 260, 270, 280
Table of Contents
Regarding this document
1.
–– Original instruction manual.
–– Part of the product.
–– Read these instructions carefully before use and keep them in a
safe place for future reference.
–– Protected by copyright.
–– No part of this manual may be reproduced without our prior
approval.
–– Subject to alterations in the interest of technical progress.
–– All dimensions are given in millimetres.
–– The drawings are not true to scale.
General safety instructions . . . . . . . . . . . . . . . . . . . . . 3
1.1 Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Target group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.
Product overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.1 Preparing for installation. . . . . . . . . . . . . . . . . . . . . . . . 4
3.2 Installing the drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.3 Connection of control elements. . . . . . . . . . . . . . . . . . . 8
3.4 Completing the installation. . . . . . . . . . . . . . . . . . . . . . 9
4.
Setting in operation. . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Overview of the controls . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Status display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.3 Express programming . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.4 Function test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.5 Special programming. . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.1 Hand transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.2 Release mechanism. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7.Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
9.
Rectifying faults. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10.Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10.1 Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
10.2 Declaration of Incorporation. . . . . . . . . . . . . . . . . . . . . 24
10.3 EC Declaration of Conformity. . . . . . . . . . . . . . . . . . . . 25
Meaning of symbols
DANGER!
Safety notice indicating a danger that will directly result in death or
severe injury.
WARNING!
Safety notice indicating a danger that could result in death or severe
injury.
CAUTION!
Safety notice indicating a danger that could result in slight or
­moderate injuries.
NOTICE
Safety notice indicating a danger that could result in damage to
property or in irreparable damage to the product.
CHECK
Reference to a check that needs to be carried out.
REFERENCE
Reference to separate documents that must be observed.
• Instruction requiring action
–– List, itemisation
DANGER!
Important safety instructions:
Attention! It is vitally important for the safety of
­persons that you follow all the instructions.
Keep these instructions in a safe place.
➔➔ Reference to other sections of this document
)) Factory settings
Important instructions for safe installation:
Attention! Serious injuries can be caused if the equipment is not installed correctly – be sure to follow all
the installation instructions.
2
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
1. General safety instructions
DANGER!
Failure to comply with the documentation could result in
life-threatening danger!
• Be sure to follow all the safety instructions in this document.
1.1 Intended use
–– The operator system is to be used only for opening and closing the
following types of door:
– Sectional doors
– Up-and-over swing-out doors
–– Only approved for use in dry rooms.
–– The maximum push and pull forces must be observed.
–– Never use the garage door to lift persons or objects.
1.3 Warranty
–– The warranty with regard to function and safety is only valid if the
instructions in this manual are observed.
Failure to observe the safety instructions could lead to personal
injury and damage to property. The manufacturer is not liable for
damage resulting from non-observance of the instructions.
–– The product is manufactured in accordance with the guidelines
and standards listed in the manufacturer’s declaration and in the
declaration of conformity. The product left the factory in perfect
order with regard to safety.
–– The warranty does not cover batteries, protection devices or light
bulbs.
2. Product overview
2 / 1
1.2 Target group
–– Installation, connection and setting in operation:
qualified, trained specialist personnel.
–– Operation, inspection and servicing:
the operator of the door system.
Requirements to be met by qualified and trained specialist staff:
–– Knowledge of the general and specific safety and accident-­
prevention regulations.
–– they have knowledge of the relevant electrical regulation,
–– Training in the use and care of appropriate safety equipment.
–– Adequate instruction and supervision by qualified electricians.
–– The ability to recognise hazards that can be caused by electricity.
–– Knowledge of the application of the following standards
– EN 12635 (“Doors and gates - Installation and use”),
– EN 12453 (“Safety in use of power operated doors Requirements”),
– EN 12445 (“Safety in use of power operated doors Test methods”),
2x
2x
2 / 2
2x
Requirements to be met by the operator of the door system:
–– Knowledge and safekeeping of the instruction manual.
–– Knowledge of general safety and accident-prevention regulations.
2x
2 / 3
4x
2x
2x
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)3
2 / 4
NOTICE
6x
6x
6x
2 / 5
2 / 6
Material damage resulting from incorrect installation of the
operator!
To avoid installation errors and damage to the door or operator
system, the following installation instructions must be observed at all
costs.
• Ensure that the door is in good mechanical condition:
– The door remains stationary in every position.
– The door can be moved easily.
– The door opens and closes properly.
• When installing the operator system, the door must be in the
closed position.
• Install all impulse transmitters and control equipment (such as
radio code buttons)
(e. g. within sight of the door and at a safe distance from the
door’s moving parts. The installation height must be at least
1.5 metres from the ground.
• Only use fixing materials that are suitable for the foundation
material in question.
3.1 Preparing for installation
Before commencing installation, the following works must be carried
out without fail.
Regional deviations are possible.
3. Installation
DANGER!
Life-threatening danger due to electric shock!
• It is vital that you disconnect the operator system from the
power supply before commencing cabling work. Take measures
to ensure that the power supply remains disconnected for the
duration of the work.
• Observe the local safety regulations.
• It is imperative that you lay power cables separately from control
cables.
The control voltage is 24 V DC.
Supply package
• Check that all the parts are present.
• Check that all the necessary accessory parts for your installation
situation are present (e.g. operator boom).
Garage
• Check to make sure that your garage has a suitable power
­connection and a mains disconnection switch.
Door system
• Remove any components (such as ropes, chains, brackets, etc.) from
the door that are no longer needed.
• All equipment that will no longer be required after the door operator system has been installed must be taken out of service.
For garages without a second entrance:
• Fit the garage door with an emergency release mechanism so that
you can gain entry to the garage if there is a malfunction.
If a release set is used:
• Check that the door catches function properly. On no account
should the door catches be taken out of service.
If no release set is used:
• Remove the door catches or take them out of service.
REFERENCE
When using and installing accessory equipment, observe the
­corresponding documentation.
4
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
3.2 Installing the drive
4x
3.2 / 1
2x
3.2 / 2
A
NOTICE
Possibility of damaging the motor unit!
Do not use force, as this could damage the teeth of the gears!
• Carefully fix the operator boom to the motor unit.
ø 5 – 5,5
3.2 / 3
A
4x
4x
B
B
ø 5 – 5,5
4x
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)5
3.2 / 7
3.2 / 4
1x
WARNING!
Possibility of serious injury due to falling components!
• Secure the operator system to prevent if from falling before it is
properly fixed in place.
3.2 / 8
NOTICE
Possibility of damaging the door leaf!
At its highest point during opening, the top edge of the door leaf
must be 10 - 50 mm below the bottom edge of the horizontal
­operator boom.
• Fix the lintel joining plate for the operator boom. It must be
­positioned centrally above the door leaf.
3.2 / 5
ø 10
10 - 50
3.2 / 9
3.2 / 6
2x
3.2 / 10
2x
2x
2x
6
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
3.2 / 11
3.2 / 15
3.2 / 12
3.2 / 16
1x
a
ø 10
1x
a = 90°
b = 9 Nm
5-10
b
3.2 / 13
3.2 / 17
2x
2x
2x
3.2 / 14
3.2 / 18
1/3
2/3
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)7
3.3 Connection of control elements
DANGER!
Life-threatening danger due to electric shock!
• It is vital that you disconnect the operator system from the
power supply before commencing cabling work. Take measures
to ensure that the power supply remains disconnected for the
duration of the work.
3.3.1 Overview of the control element connections
3.3.1 / 1
XB03
XW40
XB72
NOTICE
XW81
Danger of material damage resulting from incorrect
­installation of the operator!
If an external voltage is connected to terminal block XB03, the entire
electronic system will be irreparably damaged.
• Connect only potential-free contacts to terminals 1, 2 and 4
(XB03).
XN70
XB03
Connection for
–– external control elements
–– Photocell
➔➔ „Level 5, Menu 1 - Programmable impulse
input (terminal 1/2)“
➔➔ „3.3.3 Terminal block XB03“
XB72
Connection for modular antenna
➔➔ „3.3.2 Terminal block XB72“
XN70
Connection for battery backup
➔➔ „3.3.4 Connections XN70 and XW81“
XW40
Connection for MS bus expansion module
XW81
Connection for expansion
inputs / outputs
➔➔ „3.3.4 Connections XN70 and XW81“
3.3.2 Terminal block XB72
3.3.2 / 1
8
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
3.3.3 Terminal block XB03
3.3.4 Connections XN70 and XW81
3.3.3 / 1
3.3.4 / 1
3.3.3 / 2
- XB03
3
2
1
4
70
M11E021
1
REFERENCE
See the separate documentation for instructions on installing the
connected elements.
- Sb4
- W1
- W2
71
3.3.4 / 2
- Sb1
2
- W1
1 2
- W2
1 2
- AP27
3.3.3 / 3
2 1
2 1
TX
RX
1
GROUND
2
Impulse
3
24 V DC
4
Hold circuit, active after a reset
70
GROUND
71
Photocell
AP27
Photocell
RX
Photocell receiver
TX
Photocell transmitter
Sb1
Impulse button
Sb4
Normally closed contact for hold circuit
3.4 Completing the installation
3.4 / 1
• Take the warning signs regarding trapping hazards and affix them
permanently at noticeable locations.
• After installation is complete, ensure that no door parts extend
onto the public footpath or the street.
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)9
4. Setting in operation
Display
Function / Element
Ready for operation
Before initial operation and at regular intervals of no more than one
year, power-operated windows, doors and gates must be inspected by a
qualified person (whereby written inspection records must be kept).
After setting the system in operation, the operator of the door system,
or the operator’s representatives, must be instructed in the operation of
the system.
Door position: CLOSED
Door position: OPEN
Fault message / Maintenance indicator in CLOSED
door position
WARNING!
Danger of injury due to uncontrolled movement of the
door!
• Ensure that children can not play with the door controls or the
hand transmitter.
• Before setting the door in motion, make sure that no persons or
objects are within the danger zone of the door.
• Before going through the door opening, make sure that the door
is in the OPEN position.
• Check all the existing emergency command devices.
• Pay attention to potential crushing and shearing zones in the
door system.
• Never touch a running door, the guide rail or any moving parts.
• The regulations of DIN EN 13241-1 (“Doors and gates - Product
Standard”) must be observed.
Remote control
External button
3
Status display
(example: 3 = Battery backup connected)
➔➔ „4.2 Status display“
12
34
5678
5678
90
34
Photocell or closing edge safety device
Level indicator (example: Level 2)
12
90
4.1 Overview of the controls
Control elements
12
34
5678
90
Drive the door in the CLOSE direction, decrease
the value
Minute indicator
12
12
Menu and parameter indicator
(example: Menu 3, Parameter 8)
LED display
Drive the door in the OPEN direction, increase the
value
P
5678
90
5678
90
34
34
Times exceeding one minute are shown in
­minutes and seconds.
Example: 1.2 = 1 minute + 20 seconds = ­
80 seconds
Start programming, confirm and save values
Legend
The display flashes
Display lights up
10
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
4.2 Status display
Display
Express programming
1. Programming the “OPEN” door position
Function / Element
The control system is in
­operating mode.
3
Battery backup connected (optional)
4
Warning time indicator (only for programmed
automatic closing)
P
P > 3 sec. < 10 sec.:
Start express programming.
Drive the door to the OPEN
position.
4.3 Express programming
To set the operator system properly in service and after every reset, the
express programming procedure must be carried out.
Requirements:
–– The door must be in the CLOSED position.
–– The carriage must be coupled up.
When in programming mode, the controls will revert automatically to
operating mode if a period of 120 seconds passes without any buttons
being pressed.
A corresponding fault number will be displayed.
➔➔ „9. Rectifying faults“”
P
Save the OPEN position.
2. Programming the “CLOSED” door position
Drive the door to the CLOSED
position.
• Carry out the express programming procedure.
CHECK
P
Save the CLOSED position.
A function test must be carried out after express programming.
➔➔ „4.4 Function test“
3. Programming the remote control
Press the hand transmitter
button.
Release the hand transmitter
button.
P
Save the remote control
setting.
End express programming.
The control system is in
­operating mode.
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)11
4.4 Function test
4.4.1 Programming run for setting the driving power
During the first two runs after the door positions have been programmed, the operator system determines the maximum required
driving power.
• Drive the operator system (with the door coupled up) from the
CLOSED door position to the OPEN position and back again,
­without interruption.
• Check the driving power.
Check the driving power
1.
The control system is in
­operating mode.
2.
The door should open and
move to the saved “OPEN”
door position.
3.
4.
5.
6.
12
The door should close and
move to the saved “CLOSED”
door position.
The door operator should
move the door in the OPEN or
CLOSE direction. Richtung ZU
­bewegen.
The operator system should
stop.
4.4.2 Checking the automatic cut-out
WARNING!
Danger of injury due to incorrectly programmed values for
the door driving power!
• Check the automatic cut-out function in the OPEN and CLOSE
directions.
Automatic cut-out in the OPEN direction
This checking procedure only applies to operator systems that are
installed to operate doors that have openings in the door leaf (with
openings > 50 mm in diameter):
• During travel, apply a load of 20 kg to the door at the mid point of
the bottom edge of the door:
The door should stop immediately.
Automatic cut-out in the CLOSE direction
This checking procedure applies to all door systems.
• Place an object, 50 mm in height, on the floor.
• Drive the door towards the obstacle:
The operator system should stop and reverse when it touches the
obstacle.
The settings for the driving power in the OPEN and CLOSE directions
remain saved even if the mains power supply is interrupted.
The parameters are returned to the factory settings only after a reset.
➔➔ „Level 1, Menu 8 – RESET“
4.4.3 Checking the photocell
Photocell
• Check all the photocells individually by triggering them.
• Check all the photocells just before the door reaches the CLOSED
position.
Special points regarding door-frame photocells
–– A door-frame photocell must function above the position at which
it is installed. Below the installation position, the function of the
photocell is suppressed by the control unit.
–– If several photocells are connected, all the photocells function in
the same way as a door-frame photocell, if present.
The operator system should run
in the opposite direction.
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
5.
Select the menu required
(example Menu 3).
6.
Confirm the menu required.
Display the programmed
­parameter value.
P
Change the parameter value.
8.
Save the parameter value.
The control system switches to
display the levels
P
34
5678
34
5678
34
5678
34
5678
12
12
12
5678
90
Select the next level required.
Continue programming.
34
90
7.
5678
12
P
34
12
4.
Confirm the level required.
Display the first menu and the
programmed parameter.
5678
12
Select the level required
­(example: Level 2).
34
90
A function test must be carried out after changes have been made in
programming mode.
➔➔ „4.4 Function test“
3.
5678
90
CHECK
P
34
90
If a photocell is connected, it will be automatically detected by the
control system as soon as the power supply is connected.
The photocell can be reprogrammed later.
Photocells that are not required must be disconnected before the
power supply is connected; otherwise they will be recognised by the
controls.
➔➔ „3.3.3 Terminal block XB03“
2.
P > 10 sec.:
Start programming the
­extended operator functions.
Display the levels.
90
Material damage resulting from incorrect programming of
the door operator.
After a reset, all the parameters are returned to the factory settings.
Safety elements that are operational and are connected to the system
will be recognised anew after a reset.
To ensure that the controls functions properly:
• Reprogram all the required functions.
• Reprogram the remote control.
• Drive the operator system once to the OPEN position and then the
CLOSED position.
The control system is in
­operating mode.
90
NOTICE
1.
90
Danger of injury due to incorrect settings for the door
driving power!
Important factory settings can be changed when programming the
special functions.
• Check the programmed parameter values.
• Check the programmed door driving power values after changes
have been made to the automatic cut-out setting.
➔➔ „4.4.2 Checking the automatic cut-out“
• Carry out the necessary measurements to validate the correct
force limitation.
Programming procedure
12
WARNING!
4.5.1 Programming the special functions
12
4.5 Special programming
or
9.
P
P > 5 sec.:
Finish programming.
All the altered parameters are
saved.
The control system is in
­operating mode.
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)13
4.5.2 Overview of the special functions
Level
1
Basic functions
Menu
3 Intermediate OPEN position
4 Intermediate CLOSE position
7 Relay output
8 RESET
2
Operator settings
1 Driving power required to OPEN
2 Driving power required to CLOSE
3 Automatic cut-out in the OPEN direction
4 Automatic cut-out in the CLOSE direction
3
Automatic closing
timer
1 Automatic closing timer
3 Door open duration
4 Warning time
5 Start-up warning
4.5.3 Contents of the special functions
Level 1 – Basic functions
Menu 3 – Intermediate OPEN position
Adjust the setting using the + (OPEN) and – (CLOSE)
buttons.
The closing function with automatic closing is possible.
Only the intermediate position that was programmed last
can be used.
Menu 4 – Intermediate CLOSE position
Adjust the setting using the + (OPEN) and – (CLOSE)
buttons.
The closing function with automatic closing is not possible.
Only the intermediate position that was programmed last
can be used.
7 Signal light
4
Remote
­programming
2 Intermediate OPEN position
3 Intermediate CLOSE position
4 OPEN
1
)) Signal light (present / not present)
➔➔ „Level 3, Menu 7 - Signal light“
8 Operator lighting ON / OFF
2
Door position: OPEN
1 Programmable impulse input
3
Door position: CLOSED
3 Programmable input
4
Intermediate OPEN position
4 Lighting duration
5
Intermediate CLOSE position
5 Hand-held programming device
6
Operator system starts (wiping impulse, 1 second)
1 OPEN speed
7
Fault
2 Soft run OPEN speed
8
Lighting duration
➔➔ „Level 5, Menu 4 - Lighting duration“
9
Locking mechanism release
(operator system running)
10
Locking mechanism release
(operator system inmobile)
11
Release lock (operator system starts /
wiping impulse, 3 seconds)
1 Door cycle counter
12
Push-open security device
2 Servicing counter
13
Radio remote control (relay is activated for the
duration of the impulse)
14
Test impulse for the closing edge safety device
(relay transmits a test impulse and is activated for
300 ms)
5 CLOSE
5
Special functions
6
Variable
speed
3 Soft run OPEN position
4 CLOSE speed
5 Smart run CLOSE speed
6 Soft run CLOSE speed
7 Smart run CLOSE position
8 Soft run CLOSE position
7
Maintenance and
servicing
3 Servicing interval
8 Reset maintenance and servicing
9 Fault indicator
8
System settings
Menu 7 – Relay output
(only programmable with optional signal light relay)
1 Photocell
2 Closing edge safety device
3 Automatic cut-out function
4 Operating modes
5 Function of the direction command
­transmitters
6 Function of the impulse command
­transmitters
7 Stress relief in the CLOSED door position
(back jump)
14
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
Level 1 – Basic functions
Menu 8 – RESET
1
)) No reset
2
Reset the controls
3
Reset the remote control (telegrams are deleted)
4
Reset the special function: automatic closing timer
➔➔ „Level 3 - Automatic closing timer“
5
Reset only the special operator functions (except
the OPEN/CLOSED door positions and the remote
control impulse)
6
Reset the safety elements (photocell / Hold circuit)
7
Reset bus modules (connected bus modules will be
programmed in)
Level 2 – Door operator settings
Menu 1 – Driving power required to OPEN
Sensitivity in on a scale of 1 to 16
(the higher the number, the greater the driving power).
)) 8
Level 3 - Automatic closing timer
Menu 1 – Automatic closing timer
If the automatic closing function is activated, the ­relay
output (Level 1 / Menu 7) can be reprogrammed if
required.
1
)) Deactivated
2
Door open
duration 15 /­
­Warning time 5
3
Door open
duration 30 /
Warning time 5
4
Door open
duration 60 /
Warning time 8
5
Door open
duration 15 /
Warning time 5
6
Door open
duration 30 /
Warning time 5
7
Door open
duration 60 /
Warning time 8
8
Door open
duration infinite /
Warning time 3
Menu 2 – Driving power required to CLOSE
Sensitivity in on a scale of 1 to 16
(the higher the number, the greater the driving power).
)) 8
Menu 3 – Automatic cut-out in the OPEN direction
Sensitivity on a scale of 1 (OFF) to 16
(the lower the number, the more sensitive the automatic
cut-out).
10
The open duration can
only be increased via an
impulse signal
(button or hand
­transmitter).
The door open duration
ends after the photocell
has been triggered.
Door closes after the
­photocell has been
triggered /
Closing prevention.
Menu 3 – Door open duration
2 – 250 seconds.
)) Dependent on Level 3, Menu 1
Menu 4 – Warning time
Menu 4 – Automatic cut-out in the CLOSE direction
Sensitivity on a scale of 1 (OFF) to 16
(the lower the number, the more sensitive the automatic
cut-out).
)) 10
1 – 70 seconds.
)) Dependent on Level 3, Menu 1
Menu 5 – Start-up warning
0 – 7 seconds.
)) 0
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)15
Level 3 - Automatic closing timer
Menu 7 – Signal light
1
)) Door movement / Warning: Flashing
Door stationary: Off (energy saving)
2
Door movement / Warning: Light on
Door stationary: Off (energy saving)
3
Door movement / Warning: Flashing
Door stationary: Flashing
4
Level 5 – Special functions
Programming of the special functions is dependent on terminal block
XB03.
➔➔ „3.3.3 Terminal block XB03“
Menu 1 – Programmable impulse input (terminal 1/2)
1
)) Impulse (normally open contact only)
2
Door movement / Warning: Light on
Door stationary: light on
Closing prevention device (normally open contact
only)
3
5
Door movement / Warning: Flashing
Door stationary: Light on
Stops and reverses (only in the CLOSE direction –
normally closed contact only)
4
6
Door movement / Warning: Light on
Door stationary: Flashing
Stops and reverses (only in the CLOSE direction –
normally open contact only)
5
OPEN impulse (induction loop – normally open
contact only)
6
Earlier closing possible by pressing the buttons on
the input device or hand transmitter > 2 seconds
Level 4 – Remote programming
Menu 2 – Intermediate OPEN position
Parameter indicator flashes -> Press the hand transmitter
button -> Hand transmitter display also flashes >
The function has been programmed.
Menu 3 – Intermediate CLOSE position
Parameter indicator flashes -> Press the hand transmitter
button -> Hand transmitter display also flashes >
The function has been programmed.
Menu 4 – OPEN
Parameter indicator flashes -> Press the hand transmitter
button -> Hand transmitter display also flashes >
The function has been programmed.
Menu 3 – Programmable input (XW81)
1
Impulse (normally open contact only)
2
Impulse RC (normally open contact only)
3
Closing prevention device (normally open contact
only)
4
Stops and reverses (only in the CLOSE direction –
normally closed contact only)
5
Stops and reverses (only in the CLOSE direction –
normally open contact only)
6
OPEN impulse (normally open contact only)
7
Stop (normally closed contact only)
8
Earlier closing possible by pressing the buttons on
the input device or hand transmitter > 2 seconds
9
Automatic closing timer ON / OFF
Menu 4 – Lighting duration
Menu 5 – CLOSE
Parameter indicator flashes -> Press the hand transmitter
button -> Hand transmitter display also flashes >
The function has been programmed.
Menu 8 – Operator lighting ON / OFF
Parameter indicator flashes -> Press the hand transmitter
button -> Hand transmitter display also flashes >
The function has been programmed.
The “Radio remote control” function must not be
­programmed.
➔➔ „Level 1, Menu 7 - Relay output“
2 – 250 seconds.
)) 3.0 (180 seconds)
Menu 5 – Hand-held programming device
1
)) Operation and programming option
2
Operation only
Level 6 – Variable speed
Menu 1 – OPEN speed
On a scale of 5 to 16.
)) 16
Menu 2 – Soft run OPEN speed
On a scale of 1 to 16.
)) 7
16
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
Level 6 – Variable speed
Menu 3 – Soft run OPEN position
Adjust the setting using the + (OPEN) and – (CLOSE)
buttons.
Menu 4 – CLOSE speed
On a scale of 5 to 16.
)) 16
Menu 5 – Smart run CLOSE speed
On a scale of 5 to 16.
)) 7
Menu 6 – Soft run CLOSE speed
On a scale of 1 to 16.
)) 7
Menu 7 – Smart run CLOSED position
Adjust the setting using the + (OPEN) and – (CLOSE)
buttons.
Menu 8 – Soft run CLOSE position
Adjust the setting using the + (OPEN) and – (CLOSE)
buttons.
Level 7 – Maintenance and servicing
Menu 3 – Servicing interval
Adjustment of the number of door operations to be
­completed before a servicing reminder is displayed.
1
)) OFF
2
100 door operations
3
500 door operations
4
1,000 door operations
5
4,000 door operations
6
5,000 door operations
7
6,000 door operations
8
7,000 door operations
9
8,000 door operations
10
9,000 door operations
11
10,000 door operations
12
15,000 door operations
13
20,000 door operations
14
30,000 door operations
15
40,000 door operations
16
50,000 door operations
Menu 8 – Reset maintenance and servicing
The fault log for maintenance, diagnostics and servicing
work is reset here.
1
)) No reset
2
Reset the fault log
Menu 9 – Fault indicator
Level 7 – Maintenance and servicing
Menu 1 – Door cycle counter
Six-figure indicator showing the number of door operations, up to 999999.
Figures shown one after the other up to the indicator
point, then repeated.
Shows the current fault message.
(No more than 16 fault messages can be viewed).
Display the previous fault /
Navigate through the list of faults
Navigate through the list of faults
Menu 2 – Servicing counter
Five-figure indicator showing the number of door
­operations still to go, up to maintenance indication.
Figures shown one after the other up to the indicator
point, then repeated.
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)17
Level 8 – System settings
Door reverses a short distance:
The operator system moves the door slightly in the opposite direction
in order to release an obstacle.
Door reverses over a long distance:
The operator system moves the door all the way to the OPEN p­ osition.
Level 8 – System settings
Menu 4 – Operating modes
1
Door movement in OPEN direction: Deadman
Door movement in CLOSE direction: Deadman
2
Door movement in OPEN direction:
Press-and-release
Door movement in CLOSE direction: Deadman
3
4
1
)) Operation without photocell
Door movement in OPEN direction: Deadman
Door movement in CLOSE direction:
Press-and-release
2
2-wire photocell
(terminal block XB03 - terminal 70/71),
Door movement in CLOSE direction: door reverses
over a long distance
)) Door movement in OPEN direction:
Press-and-release
Door movement in CLOSE direction:
Press-and-release
3
External photocell
(terminal block XB03 - terminal 70/71),
Door movement in CLOSE direction: door reverses
over a long distance
Menu 1 – Photocell
Menu 5 – Function of the direction command transmitters
1
)) Direction command transmitters not activated:
The direction command transmitters trigger a
command only when the door is stationary.
2
Direction command transmitters, STOP only:
A moving door is stopped by every direction
­command transmitter.
Menu 2 – Closing edge safety device
1
)) Door movement in OPEN direction:
door ­reverses a short distance
Door movement in CLOSE direction:
door ­reverses a short distance
2
Door movement in OPEN direction:
door reverses a short distance
Door movement in CLOSE direction:
door reverses over a long distance
3
Door movement in OPEN direction:
door reverses over a long distance
Door movement in CLOSE direction:
door reverses over a long distance
4
Menu 6 – Function of the impulse command transmitters
1
Impulse command transmitters not activated:
The impulse command transmitters trigger a
­command only when the door is stationary.
2
Impulse command transmitters, STOP only, then
standard sequence:
A moving door is stopped by every impulse
command transmitter. A subsequent command will
start the operator system moving in the opposite
direction.
(OPEN - STOP - CLOSE - STOP - OPEN).
3
)) Impulse command transmitters, STOP only, then
standard sequence:
A moving door is stopped by every impulse
command transmitter. A subsequent command
will start the operator system moving in the
opposite direction
(OPEN - STOP - CLOSE - STOP - OPEN).
With automatic closing, there is no STOP in the
OPEN direction.
Door movement in OPEN direction:
door reverses over a long distance
Door movement in CLOSE direction:
door reverses over a long distance
Menu 3 – Automatic cut-out function
18
1
)) Door movement in OPEN direction: door stops
Door movement in CLOSE direction:
door r­ everses a short distance
2
Door movement in OPEN direction:
door reverses a short distance
Door movement in CLOSE direction:
door reverses a short distance
3
Door movement in OPEN direction: door stops
Door movement in CLOSE direction:
door reverses a short distance
4
Door movement in OPEN direction:
door reverses over a long distance
Door movement in CLOSE direction:
door reverses over a long distance
5
Door movement in OPEN direction:
door reverses a short distance
Door movement in CLOSE direction:
door reverses over a long distance
Menu 7 – Stress relief in the CLOSED door position
(back jump)
1
)) Back jump not activated
2
Back jump activated – short
3
Back jump activated – medium
4
Back jump activated – long
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
5. Operation
WARNING!
Danger of injury due to uncontrolled operation of the
door!
• Operate the controls or the hand transmitter only when there are
no persons or objects in the path of the door.
• Ensure that the controls and the hand transmitter are never used
by children or unauthorised persons.
• Ensure that the hand transmitter cannot be operated by accident
(in a trouser pocket, for example).
Transmitting the code
1.
Connect the hand transmitter to
the transmission plug.
2.
Press the button on the master
transmitter.
Keep the button pressed.
The LED lights up.
3.
Press the button on the hand
transmitter which is to be given a
new code.
The LED flashes.
4.
The LED lights up.
The coding procedure is
­completed.
5.
Remove the transmission plug.
NOTICE
Danger of damage to property due to uncontrolled
­movement of the door!
When the door moves, the hand chain can get caught and this
could result in damage (in the case of ceiling-mounted supports for
­example).
• Ensure that there are no obstacles blocking the path of the door
or the hand chain.
5.1 Hand transmitter
The operator works with the supplied hand transmitter on the basis of
a pulse sequence control system.
Operating the door using the hand transmitter
1.
2.
3.
4.
For multi-button transmitters, each button can be programmed with a
different function.
Changing the code
The control system is in
­operating mode.
1.
Plug the transmission plug into the
hand transmitter.
1. Impulse:
The door opens and moves in
the OPEN direction
2.
Short-circuit one of the two outer
pins with the centre pin adjacent
to it (e.g. using a screw driver).
2. Impulse.
The operator system stops.
3.
Press the desired button on the
hand transmitter.
The LED flashes.
3. Impulse:
The door moves in the opposite
direction (CLOSE direction).
4.
The LED lights up.
The coding procedure is
­completed.
5.
Remove the transmission plug.
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)19
After the hand transmitter has been re-coded, the operator system
must also be re-programmed to respond to the new code.
For multi-channel transmitters, the programming process must be
­carried out for each button separately.
Changing the battery
1
1.
Open the hand transmitter.
5.2 Release mechanism
CAUTION!
Danger of injury due to uncontrolled movement of the
door!
When the release mechanism is operated, uncontrolled door
­movements could occur:
–– If the door springs are weak or broken.
–– If the door is not balanced.
• When the mechanism is released, only move the door carefully
and at a moderate speed!
NOTICE
2.
Replace the battery.
Danger of damage to property due to uncontrolled
­movement of the door!
When opening the door manually, the carriage could collide with the
carriage stop.
• When the mechanism is released, only move the door carefully
and at a moderate speed!
5.2 / 1 5.2 / 2
20
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
6. Maintenance
To ensure fault-free operation, the door system must be inspected
regularly and, if necessary, be repaired. Before starting work on the
door system, the operator system must always be disconnected from
the power supply.
• C
heck once a month that the operator system reverses when the
door touches an obstacle. To check this, place an obstacle, 50 mm
in height, in the path of the door in the direction of travel.
• Check the settings of the automatic cut-out in the OPEN and
CLOSE directions.
• Check all the moving parts of the door system and door operator
system.
• Check the door system for signs of damage or wear and tear.
• Move the door manually to check that the door travels easily and
smoothly.
Care and cleaning
• When cleaning the operator system, never use:
direct water jets, high pressure cleaners, acids or alkaline solutions.
7. Disassembly
The system must be disassembled by following the instructions in
reverse.
8. Disposal
Do not dispose of old equipment or batteries with the normal household waste!
• Dispose of old devices at a waste collection centre for electronic
waste or via your specialist dealer.
• Dispose of old batteries in a battery recycling container or via a
specialist dealer.
• Dispose of the packaging material in the special waste collection
containers for paper, cardboard and plastic.
9. Rectifying faults
Faults with no fault messages
LCD display does not light up or display information.
No supply voltage present.
• Check that the mains voltage supply is operational.
• Check the electrical connection.
The thermal overload protection in the mains transformer
has been triggered.
• Allow the transformer to cool down.
Control unit defective.
• Have the operator system checked.
No reaction after impulse signal.
Connection terminals for “impulse” button are bridged,
e.g. due to flat terminals or a short circuit in the wiring.
• If key switches or interior push buttons are connected, try disconnecting them from the control unit:
remove cables from the XB03 terminal block, insert
the shorting plug and search for the wiring fault.
➔➔ „3.3.3 Terminal block XB03“
No reaction after an impulse signal has been transmitted by
the hand transmitter.
Modular antenna is not plugged in.
• Connect the modular antenna to the control unit.
➔➔ „3.4 Completing the installation“
Hand transmitter code does not correspond to the
­receiver code.
• Activate the hand transmitter anew.
➔➔ „4.3 Express programming“
The battery in the hand transmitter is empty.
• Insert new battery.
➔➔ „5.1 Hand transmitter“
Remote control deactivated (“external button“ symbol
flashes).
• Reactivate remote control by pressing + (OPEN) or
– (CLOSE) button on the operator.
The hand transmitter, control electronics or modular
antenna are defective.
• Have all 3 components checked.
The operator system reverses when the door-frame
­photocell is triggered.
The system was not programmed correctly.
• Reset the safety devices.
➔➔ „Level 1, Menu 8 – RESET“
• Carry out the express programming procedure again.
➔➔ „4.3 Express programming“
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)21
Faults with fault messages
Faults with fault messages
The system indicates recognised faults by showing a fault number (example: fault number 7).
The control system switches to reporting mode.
In operating mode, the last fault number can be
shown by pressing the P button.
Fault number 28
Fault number 7
Programming mode will end automatically if 120 seconds
elapse without a button being pressed.
• Start the programming procedure again.
Fault number 9
Rotational speed sensor impulse not present,
operator system is obstructed.
• Have the operator system checked.
Fault number 10
The door does not move easily or is obstructed.
• Take measures to ensure that the door moves freely
and smoothly.
The maximum driving power has been set too low.
• Have the maximum driving power checked by a
specialist dealer.
➔➔ „Level 2, Menu 1 - Driving power required to OPEN“
➔➔ „Level 2, Menu 2 - Driving power required to CLOSE“
The door does not move easily or smoothly or is
­obstructed.
• Check the door movement and take measures to
ensure that the door moves freely and smoothly.
Automatic cut-out setting is too sensitive.
• Have the automatic cut-out function checked by a
specialist dealer.
➔➔ „Level 2, Menu 3 – Automatic cut-out in the OPEN
direction“
➔➔ „Level 2, Menu 4 – Automatic cut-out in the CLOSE
direction“
Fault number 30
MS bus fault.
• Reset the bus modules.
➔➔ „Level 1, Menu 8 – RESET“
• Have the connected bus modules checked.
Fault number 33
Rise in temperature due to overheating.
• Allow the motor unit to cool down.
Fault number 35
Electronic defect.
• Have the operator system checked.
Fault number 11
Excess travel stop.
• Have the operator system checked.
Fault number 15
Photocell triggered or defective.
• Remove obstacle or have the photocell checked.
Fault number 36
Wire jumper removed but stop button not connected.
• Plug in stop button or insert shorting plug.
➔➔ „3.3 Connection of control elements“
Operator system released or closed circuit interrupted.
• Engage the operator system.
Photocell programmed but not connected.
• Deactivate or connect the photocell.
Fault number 16
The current sensor for the automatic cut-out is defective.
• Have the motor unit checked.
Fault number 26
The operator system is overloaded when the driving
power is set to 16 (maximum).
• Have the external power supply checked.
22
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
Supply package
Reference point technology
10. Appendix
Soft start / Soft stop
Push-open security device
10.1 Technical Data
Electrical data
Rated voltage, regional deviations
are possible
Automatic cut-out
Obstruction protection
Undervoltage protection
V
230 / 260
Rated frequency
Hz
50 / 60
Current input
A
1.1
Power consumption in operation*
kW
0.25
Power consumption in standby*
W
approx. 4
Duty cycle
min.
short-term 2
Control voltage
V DC
24
Protection category of motor unit
IP 20
Protection class
II
* without any additional equipment connected
Travel speed
Opening time, dependent on door
type
Electronic travel cut-out
Connection for push button, code button and key button
Connection for potential-free limit-switch message system
Modular antenna
Fault signalling
Accessories
Mounting brackets for sectional doors
Release sets for up-and-over doors
Adapter arm for retractable up-and-over doors
Door fittings for swing doors
Mechanical data
Max. push and pull force
Excess travel stop
N
Comfort 260: 550
Comfort 270: 750
Comfort 280: 1,000
mm/s
160
s
approx. 14
Photocells
Release system
Relay for flashing signal light for use with automatic closing system
Retrofit kit for potential-free limit switches OPEN/CLOSE/LIGHT
Push button
Key switch
Code button
Environmental data
Dimensions of motor unit
mm
190 x 125 x 360
Weight (total)
kg
Comfort 260: 6.4
Comfort 270: 6.5
Comfort 280: 6.6
dB(A)
< 70
°C
-20
°C
+60
Sound pressure level
Temperature range
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)23
10.2 Declaration of Incorporation
We hereby declare that in its design and construction, and in the form
as delivered, the product mentioned below complies with the relevant
basic requirements of the EC Machinery Directive (2006/42/EC).
This declaration shall no longer be valid if changes are made to the
product without our authorisation.
Person authorised to compile the relevant technical documentation:
Marantec Antriebs- und Steuerungstechnik
GmbH & Co. KG
Remser Brook 11 · 33428 Marienfeld · Germany
Phone: +49 5247 705-0
Product: Garage door operator Comfort 260, 270, 280
Revision status: R01
In addition, the partly completed machinery is in ­conformity with the
EC Construction Products Directive 89/106/EC, the EC Electromagnetic
Compatibility Directive 2004/108/EC and the EC Low Voltage Directive
2006/95/EC.
–– Machinery Directive 2006/42/EC
–– Health and safety requirements applied according to Annex 1:
–– General principles No. 1 No. 1.1.2, 1.1.3, 1.1.5, 1.2.1, 1.2.2, 1.2.3,
1.2.6, 1.3.1, 1.3.4, 1.3.7, 1.3.8, 1.3.9, 1.5.1, 1.5.4, 1.5.6, 1.5.8,
1.5.14, 1.7
EN 60204-1:2007
EN ISO 12100-1:2003
EN ISO 13849-1:2008
Cat. 2 / PLC for the functions of power limitation and end position
detection
–– EN 61508:2001
–– EMC electromagnetic compatibility 2004/108/EC
EN 55014-1
EN 61000-3-2:2006 (2008)
EN 61000-3-3:2009
EN 61000-6-2:2006
EN 61000-6-3:2007
–– Low voltage directive 2006/95/EC
EN 60335-1:2002
EN 60335-2-103:2004
The relevant technical documentation is compiled in accordance with
Annex VII(B) of the Machinery Directive 2006/42/EC. We undertake to
transmit, in response to a reasoned request by the market surveillance
authorities, this information in electronic form within a reasonable
term.
The machinery is incomplete and must not be put into service until
the machinery into which it is to be i­ncorporated has been declared in
conformity with the provisions of the Machinery Directive 2006/42/EC.
01.07.2012
ppa. K. Goldstein
Management
24
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)
10.3 EC Declaration of Conformity
We hereby declare that in its design and construction, and in the
form as brought onto the market by us, the product mentioned below
complies with the relevant basic requirements of the EC directives
mentioned below.
This declaration shall no longer be valid if changes are made to the
product without our authorisation.
Product:
Door designation
Operator designation
Relevant EC directives:
–– Construction Products Directive 89/106/EEC
–– Machinery Directive 2006/42/EC
–– Electromagnetic Compatibility 2004/108/EC
–– Low Voltage Directive 2006/95/EC
The relevant technical documentation is compiled in accordance with
Annex VII(B) of the Machinery Directive 2006/42/EC. We undertake to
transmit, in response to a reasoned request by the market surveillance
authorities, this information in electronic form within a reasonable
term.
The machinery is incomplete and must not be put into service until
the machinery into which it is to be i­ncorporated has been declared in
conformity with the provisions of the Machinery Directive 2006/42/EC.
Installer
Address, postcode, town/city
Date / Signature
Operating instructions, Comfort 260, 270, 280 (#100316 – GB)25
Type plate
Typ (A)
Rev (B)
___________________________________________________________________________________________
Art. No. (C)
Prod. No. (D)
___________________________________________________________________________________________
___________________________________________________________________________________________
___________________________________________________________________________________________
/
B
Remser Brook 11
DE - 33428 Marienfeld
MADE IN GERMANY
100316
i
C
D
1 - GB 360347 - M - 0.5 - 1111
A