VADDIO 999-6950-000 Specifications

Professional
Camera Systems
for Integrators
Table of Contents
Operator Controlled Camera Systems
Signal Processors/Encoders
Studio Consoles
Racks
Monitors
Camera Tracking Systems
Automated Content Presentation Systems
Vaddio HD PTZ Cameras
HideAway Camera Systems
REVEAL HD PTZ Cameras
OEM PTZ Cameras
EZ Camera Systems
Videoconferencing Peripherals
Videoconferencing Mounts
Document Cameras
IN-Wall Camera Mounts
Ceiling Mounts
Wall Mounts
Dome Camera Systems
1
10
11
13
14
15
18
24
28
29
30
37
38
39
40
41
42
43
44
an Operator Controlled Camera System
1
Camera Locations
Select the locations where cameras will be placed
to get adequate room coverage and proper viewing
angles. Determine how many PTZ cameras are
needed. Main items to consider include:
Measure the distance from the cameras to the main
subject or presenter. This is helpful in determining
what kind of optical zoom lens is needed for each
camera position.
The viewing angle calculations can be obtained
by downloading the PTZ Image Size Calculator
at www.vaddio.com/tech-center.php.
Decide if more than one camera is needed to cover
the main subject, and determine how and when you
need to switch between the shots of the main subject
or presenter.
If side cameras are needed in your design, these
should be positioned between 30-45 degrees from
the center of the room and allow the camera operator
to take shots of the presenter walking towards or
away from the camera. A single camera can only
show one side profile of the presenter.
Determine if there are locations, other than the front
of the room, that need to be covered by the primary
cameras — such as choir loft, audience, remote
rooms, etc. Another camera, or cameras may be
required to cover these locations.
2
Camera Types
Select the type of cameras based on the environment
they will be used in. Main items to consider include:
If the cameras will be used in an IMAG (Image
Magnification) projector application, then high
definition (HD) cameras are better suited in order to
achieve a detailed image on a large screen.
What is the best quality that the viewer is going to
want or need? For example, if streaming video is
the best quality, then standard definition video will
probably suffice. However, if there will also be a
need for a high resolution archive copy of the same
streamed content, then HD cameras will be a better
choice.
How much light is available in the room? If the room
is dark and shadowy, a camera with a minimum
illumination specification of 4 lux or less may be
required. Avoid fluorescent lighting with cameras
using shutter iris. Nevertheless, testing and
measuring under the proposed lighting is the best
way to decide what camera is the ideal choice.
Will you be following the presenter with a joystick or
using camera presets? If you are planning on doing
a lot of tight follow shots, make sure that the PTZ
camera uses servo or micro-stepper motors. If you
plan on using presets, PTZ cameras with direct drive
motors will be more than sufficient.
3
Additional Sources
Decide what additional sources will be switched
through the camera control system. Main items
to consider include:
• Computer sources
• Video playback, such as a DVD, VCR, etc.
• Stationary cameras, such as a POV or
document camera
• Other video feeds
4
Operator Considerations
When controlling a pan, tilt, zoom camera the main
things to consider include:
Will you be using a multi-person control room with
one person to operate the switcher and another
person operating the PTZ camera controller?
If one person will be operating the equipment, then a
camera controller with an integrated video switcher
such as the ProductionVIEW HD MV with TeleTouch
monitor is a good option.
If there are multiple people in the control room,
a stand-alone camera controller such as Vaddio’s
Precision Camera Controller is a good choice.
Does the situation require a separate camera operator
using a camera mounted on a tripod to be able to
follow the presenter? If so, place robotic cameras at
other positions than the location(s) where a camera
operator is needed.
Operator Controlled System Configuration
Call 800-572-2011 Toll Free
vaddio.com
1
Operator Controlled Camera Systems
ProductionVIEW HD MV/HD-SDI MV, ProductionVIEW HD/HD-SDI and ProductionVIEW FX make up the family of
seamless switchers, while ProductionVIEW Super Joystick and ProductionVIEW Precision Camera Controller
exclusively handle robotic camera control.
Each ProductionVIEW switcher/mixer console has an internal 6 x 2
seamless matrix video switcher (for Preview and Program). A 3-Axis
Hall-Effect Joystick controls up to six PTZ cameras directly (without daisy
chaining) through six discrete auto-sensing RS-232 camera control ports.
There are 12 presets per camera for storing frequent shots, totaling
72 presets per console. With the addition of input triggers, such as the
Vaddio PresenterPOD, StepVIEW Mats, AutoVIEW IR sensors, MicVIEW
or TouchVIEW, the ProductionVIEW consoles can be programmed to
automatically switch between cameras and presets, similar to how the
ControlVIEW XHD operates. ProductionVIEW HD MV/HD-SDI MV offers
the same functionality as Vaddio’s existing ProductionVIEW HD, with the
addition of multiviewer capabilities and digital inputs/outputs.
The ProductionVIEW Super Joystick and Precision Camera Controller use
the camera control portion of the ProductionVIEW seamless switchers.
Like the switchers, both have discrete, auto-configuring RS-232 control
ports for direct control of PTZ cameras – six in Super Joystick, seven in
Precision Camera Controller – eliminating the need for daisy chaining.
Each camera can also have internally stored camera presets, 12 in
Super Joystick, 14 in Precision Camera Controller – and can be adjusted
individually for the operating environment with auto/manual focus, auto/
manual brightness, backlight compensation and one push automatic
white balance. There is also provision for external control of select HD
switcher/mixers with built-in RS-232 commands.
The Precision Camera Controller integrates CCU image control
functionality into the system allowing users to control red and blue gain,
detail and iris with adjustable gain. Designed to control up to seven PTZ
cameras, two Precision Camera Controllers can also be linked together
to allow the user to control up to 14 cameras from either controller.
ProductionVIEW™ Series of Camera Consoles
ProductionVIEW HD MV
ProductionVIEW HD MV
North America 999-5625-000
International 999-5625-001
Camera Control Console with HD, DVI-D, RGBHV and SD video switching, transitions,
built-in multiviewer, lower screen graphics and automated control functionality.
ProductionVIEW HD-SDI MV
ProductionVIEW HD-SDI MV
North America 999-5655-000
International 999-5655-001
Camera Control Console with HD-SDI, SD-SDI and DVI-I video switching, with the addition
of multiviewer capability and digital inputs/outputs.
ProductionVIEW HD
ProductionVIEW HD
North America 999-5600-000
International 999-5600-001
Camera Control Console with HD, RGBHV and SD video mixing, transitions,
lower screen graphics and automated control functionality.
ProductionVIEW HD-SDI
ProductionVIEW HD-SDI
North America 999-5650-000
International 999-5650-001
Camera Control Console with HD-SDI and SD-SDI video switching, video mixing
and automated control functionality.
ProductionVIEW FX
ProductionVIEW FX
North America 999-5200-000
International 999-5200-001
Camera Control Console with standard definition matrix video switching, camera preset
control and joystick camera control functionality.
Precision Camera Controller
ProductionVIEW Precision Camera Controller
North America 999-5700-000
International 999-5700-001
Broadcast-quality joystick controller designed for smooth and accurate pan, tilt and zoom
control, as well as CCU image control functionality.
ProductionVIEW Super Joystick
ProductionVIEW Super Joystick
North America 999-5300-000
2
International 999-5300-001
Joystick controller with six individual RS-232 camera control ports for accurate pan,
tilt and zoom control.
Call 800-572-2011 Toll Free
vaddio.com
Operator Controlled Camera Systems
ProductionVIEW HD MV
ProductionVIEW HD Component Cables
ProductionVIEW HD MV offers the same cutting-edge processor technology as the
existing ProductionVIEW HD, with the addition of multiviewer capability, a DVI-I input and
DVI-D/HDMI outputs on both the multiviewer and program outputs. Combined with the
new TeleTouch Multiviewer Touchscreens, you can easily switch all live feeds and create
up to 12 “video thumbnails” of preset shots by simply touching the monitor. The “video
thumbnails” provide an easy way to identify and recall preset camera positions on a perinput basis in the preview window.
3 ft. Cable - DE-15 to 5 Male BNCs (YPbPr or RGBHV signals)
The 6 x 2 multi-format, seamless video mixer provides two discrete outputs for dual bus
program feeds (two independent 6 x 1 mixers). Input signals include analog HD YPbPr
video, RGBHV, SD (Y/C and CVBS), and Input 6 provides a DVI-I input for RGBHV, DVI-D and
HDMI. The Program and Preview outputs have both analog (YPbPr, RGBHV, Y/C & CVBS) and
digital (DVI-D & HDMI) outputs. HD resolutions up to 1080/60p are supported.
7 in. Cable - DE-15 to 5 Female BNCs (YPbPr or RGBHV signals)
ProductionVIeW HD Component Cable - 3 ft.
440-5600-001
6 ft. Cable - DE-15 to 5 Male BNCs (YPbPr or RGBHV signals)
ProductionVIeW HD Component Cable - 6 ft.
440-5600-002
ProductionVIeW HD Component Cable - 7 in.
440-5600-003
ProductionVIEW HD Y/C & Composite Cable
DE-15 to 3 Female BNCs (Y/C and Composite)
1 ft. Cable
ProductionVIeW HD Y/C & Composite Cable - 1 ft.
440-5600-000
ProductionVIeW HD MV system Configuration
ProductionVIEW HD MV Rear Panel
ProductionVIeW HD MV
North america
999-5625-000
International
999-5625-001
F e at u r e s
include analog HD YPbPr video, RGBHV,
SD (Y/C and CVBS), and Input 6 provides
a DVI-I input for RGBHV, DVI-D and HDMI
• The Program and Preview outputs have both analog (YPbPr,
RGBHV, Y/C & CVBS) and digital (DVI-D & HDMI) outputs
• All inputs auto-recognize video input resolution
• HD resolutions up to 1080/60p are supported
• Seamless integration with optional TeleTouch
multiviewer touch screen
• Up to 12 preset “video thumbnails” per PTZ camera
• Transitions include cross fade, nine wipes,
cut and fade to black
• Lower Screen Graphics feature for inserting
graphics over video
• 3-Axis Hall-Effect Joystick
• Knobs for adjusting focus, iris, transition speed
and pan/tilt/zoom built into the console
• Inputs
teletouch 22" HD touch screen LCD Monitor with Base
The new TeleTouch Multiviewer Touchscreen Monitors allow you to easily see and
switch all live video feeds and create “video thumbnails” with finger-touch control. The
multiviewer can be configured to display up to six input windows and two larger “Preview”
and “Program” windows with red and green tally window borders. The Preview output is
configurable for analog and digital outputs and allows for either a standard preview output
or the multiviewer output. In addition, each camera input can have up to 12 stored “video
thumbnail” preset camera shots. The TeleTouch Touchscreen Monitors are available in two
sizes: 18.5-inch rack-mount or a standard 22-inch with base.
**For more information on the teletouch Monitors please see page 14
TeleTouch 22" with 4 Inputs
Call 800-572-2011 Toll Free
vaddio.com
TeleTouch 22" with 5 Inputs
TeleTouch 22" with 6 Inputs
3
Operator Controlled Camera Systems
ProductionVIEW HD-SDI MV
ProductionVIEW HD-SDI MV System Configuration
ProductionVIEW HD-SDI MV offers the same functionality as Vaddio’s existing
ProductionVIEW HD-SDI, with the addition of multiviewer capability and a DVI-I input.
Combined with the new TeleTouch HD Touch Screen Monitor options, you can easily switch
all live feeds and create up to 12 “video thumbnails” of preset PTZ camera shots by simply
touching the TeleTouch screen. The “video thumbnails” provide an easy way to identify and
recall preset camera positions on a per-input basis in the preview window.
Input signals include HD-SDI, SD-SDI on five of the inputs, while the sixth input is an
analog/digital input that will accept a variety of video resolutions. The Program and Preview
outputs have both HD-SDI/SDI and HDMI outputs with HD resolutions up to 1080p/60
supported.
teletouch 18.5" HD touch Screen rack Mount LCD Monitor
ProductionVIEW HD-SDI MV Rear Panel
ProductionVIEW HD-SDI MV
North America
999-5655-000
International
999-5655-001
F E At u r E S
output, eliminates the need for individual
monitors for each video input
• All inputs can accept digital signals, with 5 capable of
accepting HD-SDI/SDI video and the sixth having the ability
to accept RGBHV, YPbPr or DVI-D
• All inputs auto-recognize video input resolution
• The Program and Preview outputs have both HDMI
and HD-SDI/SDI outputs
• HD resolutions up to 1080p/60 are supported
• Touch screen switching of video sources with the addition of
our optional TeleTouch HD touch screen monitors
• Up to 12 preset “video thumnails” per PTZ camera
• Transitions include cross fade, cut, nine wipe patterns and
fade to black
• Lower Screen Graphics feature for inserting graphics over
video
• 3-Axis Hall-Effect Joystick
• Knobs for adjusting focus, iris, transition speed and pan/tilt/
zoom, built into the console
The new TeleTouch Multiviewer Touchscreen Monitors allow you to easily see and
switch all live video feeds and create “video thumbnails” with finger-touch control. The
multiviewer can be configured to display up to six input windows and two larger “Preview”
and “Program” windows with red and green tally window borders. The Preview output is
configurable for analog and digital outputs and allows for either a standard preview output
or the multiviewer output. In addition, each camera input can have up to 12 stored “video
thumbnail” preset camera shots. The TeleTouch Touchscreen Monitors are available in two
sizes: 18.5-inch rack-mount or a standard 22-inch with base.
**For more information on the teletouch Monitors please see page 14
• Multiviewer
TeleTouch 18.5" with 4 Inputs
TeleTouch 18.5" with 5 Inputs
TeleTouch 18.5" with 6 Inputs
Insert graphics onto your video through our unique LSG function.
1/3 Lower Screen Graphic (Transparent)
4
Call 800-572-2011 Toll Free
vaddio.com
Operator Controlled Camera Systems
ProductionVIEW HD
ProductionVIEW HD Component Cables
The ProductionVIEW HD multi-camera control system is designed to handle the most
demanding live broadcast or staging events, yet it’s simple enough to allow a novice
to shoot like a pro. ProductionVIEW HD integrates PTZ camera control and multi-format
HD/SD live switching with real-time graphics and effects into one easy-to-use control
console.
3 ft. Cable - DE-15 to 5 Male BNCs (YPbPr or RGBHV signals)
The completely redesigned surface gives system users real-time knobs and buttons to
control functions. Because ProductionVIEW HD is a live broadcast console, not a computer,
the entire system produces only one frame of delay — a critical requirement where image
magnification is used.
ProductionVIEW HD Component Cable - 3 ft.
440-5600-001
6 ft. Cable - DE-15 to 5 Male BNCs (YPbPr or RGBHV signals)
ProductionVIEW HD Component Cable - 6 ft.
440-5600-002
7 in. Cable - DE-15 to 5 Female BNCs (YPbPr or RGBHV signals)
ProductionVIEW HD Component Cable - 7 in.
440-5600-003
ProductionVIEW HD Y/C & Composite Cable
DE-15 to 3 Female BNCs (Y/C and Composite)
1 ft. Cable
ProductionVIEW HD Y/C & Composite Cable - 1 ft.
440-5600-000
ProductionVIEW HD system Configuration
ProductionVIEW HD
North america
999-5600-000
International
999-5600-001
F E at u r E s
HD/SD Inputs can be scaled or converted
from 480i (SD) to 1080p (HD)
and a variety of analog RGBHV resolutions
• Transitions include cross fade, nine wipes,
cut, fade to black (FTB)
• 3-Axis Hall-Effect Joystick
• 12 camera presets
• Lower Screen Graphics feature
for inserting graphics over video
• Knobs for adjusting focus, iris,
transition speed and pan/tilt/zoom built into the console
• Trigger inputs for camera switching
• Discrete pan, tilt and zoom speed knobs.
• Six
Insert graphics onto your video through our unique LSG function. A variety of sizes and transparency levels are available through buttons on the console. (see more examples on next page)
Full Screen Lower Screen Graphic (Transparent)
Call 800-572-2011 Toll Free
vaddio.com
1/4 Lower Screen Graphic (Transparent)
5
Operator Controlled Camera Systems
ProductionVIEW HD-SDI
House of Worship System Configuration
Due to the increased demand for Serial Digital Interface (SDI), Vaddio created the
ProductionVIEW HD-SDI multi-camera control system with an integrated 6 x 2 HD-SDI/SDI
seamless video switcher. Because the majority of robotic PTZ cameras currently available
on the market offer HD-SDI or SD-SDI cards, the ProductionVIEW HD-SDI is designed to
connect easily via a single coax cable for video. ProductionVIEW HD-SDI includes the
3 Gb/s HD-SDI standard (SMPTE 424M) for 1080p video, as well as SMPTE 292M (HD-SDI
at 720p or 1080i) and SMPTE 259M (SD-SDI).
ProductionVIEW HD-SDI
North America
999-5650-000
International
999-5650-001
F E At u r E S
any combination of input signals
from HD-SDI and SDI video sources
(HD-SDI at 1080p, 1080i and 720p; SD-SDI)
• Transitions include cross fade, nine wipes, cut, fade to black (FTB)
• 3-Axis Hall-Effect Joystick
• 12 camera presets
• Lower Screen Graphics feature for inserting graphics over video
• Knobs for adjusting focus, iris, transition speed
and pan/tilt/zoom built into the console
• Accepts
ProductionVIEW HD-SDI Configuration
Canon BU-51H
Insert graphics onto your video through our unique LSG function. A variety of sizes and transparency levels are available through buttons on the console. (see more examples on previous page)
1/3 Lower Screen Graphic (Transparent)
6
1/4 Lower Screen Graphic (Transparent)
Call 800-572-2011 Toll Free
vaddio.com
Operator Controlled Camera Systems
ProductionVIEW FX
ProductionVIEW FX System Configuration
The ProductionVIEW FX standard definition camera control system incorporates 6 x 2 matrix
video switching, camera preset control and joystick control functionality into one easy-to-use
console.
ProductionVIEW FX delivers user-selectable, frame-synchronized transitions that are
completely seamless, professional and without compromise in quality. Among the included
transitions are straight cuts, fades (in and out), cross fades (one image fading into another)
and wipes (up, down and side to side). The user can select the transition and the transition
time, up to four seconds, to automatically activate as the inputs are switched on the main
and preview buses.
ProductionVIEW FX
NTSC
999-5200-000
PAL
999-5200-001
FEATURES
discrete auto-sensing camera control ports
• Transitions include fades, cross fades and wipes (5)
• 3-Axis Hall-Effect Joystick
• 12 camera presets per camera
• Master RS-232 port for external control systems
• Trigger inputs for camera switching
• Six
City Council Chambers System Configuration
Call 800-572-2011 Toll Free
vaddio.com
7
Operator Controlled Camera Systems
ProductionVIEW Precision Camera Controller
Precision Camera Control LINK support Configuration
The Precision Camera Controller includes a broadcast-quality joystick designed for smooth
and accurate pan, tilt and zoom control, as well as CCU image control functionality for
controlling up to seven PTZ cameras. By integrating CCU control into the system, users
can control red and blue gain, detail, and iris with adjustable gain with any Vaddio PTZ
camera. One-push white balance (OPWB), auto white balance (AWB) and auto iris are also
available to those who desire a more automated image control system. The CCU control
surface gives system users real-time knobs and buttons to control each of these functions.
Designed to control up to seven PTZ cameras, the Precision Camera Controller can be used
as a stand-alone device or in conjunction with a variety of video switchers or mixers on the
market today. In addition, two Precision Camera Controllers can be linked together to allow
the user to control all cameras from either controller.
ProductionVIeW
Precision Camera Controller
North america
999-5700-000
International
999-5700-001
F e at u r e s
• Red and blue gain, detail, iris with adjustable gain controls
• One-push white balance (OPWB), auto white balance (AWB)
and auto iris
• Large focus wheel for fast, accurate manual focus
• 3-Axis Hall-Effect Joystick
• Seven discrete auto-sensing RS-232C camera control ports
• External control capability (RS-232 and Tally)
• Link port for linking to second Precision Camera Controller
up to 500 feet away on a single Cat. 5 cable
•
Precision Camera Control external switcher support Configuration
Single Precision Camera Controller RS-232 Out to External Switcher
14 presets per camera
Precision Camera Control Dual LINK support Configuration
8
Call 800-572-2011 Toll Free
vaddio.com
Operator Controlled Camera Systems
ProductionVIEW Super Joystick
Vaddio/Sony Joystick Control Bundle
The ProductionVIEW Super Joystick is a unique integration joystick with six discrete, autoconfiguring RS-232C camera control ports for direct control of PTZ cameras, eliminating
the need for daisy chain control cabling.
Each camera can have up to 12 internally stored camera presets effectively removing the
internal preset limitations of the camera. The six cameras can also be adjusted individually
for the operating environment with adjustments for auto/manual focus, auto/manual
brightness, backlight compensation and one-push automatic white balance.
The ProductionVIEW Super Joystick has two rows of six external control switches that can
be used to trigger outputs and control external video switchers with contact closures or
tally lights for studio applications. There is also provision for external control of select HD
switchers/mixers with built-in RS-232 codes in the system menu. Super Joystick also has
a 4-inch LCD preview monitor built-in.
The Sony Remote Control Joystick can control all
camera settings including the pan/tilt/zoom functions
and six preset patterns. The bundle includes the
Sony RM-BR300 Joystick and all the custom cables
that easily interface with the Vaddio EZCamera
Cabling System.
Vaddio/Sony
Joystick Control Bundle
NTSC
999‑6605‑000
PAL
999‑6605‑001
F E AT U R E S
•
•
Custom 20-foot VISCA cable
Custom 20-foot video switcher cable
Basic System Configuration
WallVIEW CCU HD1 System and ProductionVIEW Super Joystick Controller
ProductionVIEW Super Joystick
North America
999‑5300‑000
International
999‑5300‑001
F E AT U R E S
discrete auto-sensing RS-232C camera control ports
• 12 camera presets per camera
• External control capability (Triggers and Tally)
• Master RS-232 port for external control systems
• Six
ProductionVIEW Super Joystick Controller with HD Switcher Configuration
Call 800-572-2011 Toll Free
vaddio.com
9
Signal Processors / Encoders
YPbPr to DVI-D/HDMI PRO Format Converter
UXHD CrossPoint™
The YPbPr to DVI-D/HDMI PRO Format Converter changes analog component video to a
DVI-D/HDMI video output. The converter works with ProductionVIEW HD, AutoPresenter,
ControlVIEW XHD, CeilingVIEW HD or any other analog HD video source. Whether the output
signal is 480i, 576i, 720p, 1080i or 1080p, video can be converted to a digital signal to
work with a variety of third-party devices, such as videoconference codecs and multiformat switchers.
The UXHD CrossPoint is a dual input, dual output video format converter and scaler for
HD-SDI and analog video signals (HD component (720p/1080i/1080p), SD composite and
S-Video, and RGBHV up to 1920 x 1200).
YPbPr to DVI‑D/HDMI
PrO Format Converter
North america
999‑5643‑000
International
999‑5643‑001
F e at u r e s
analog component (SD or HD) to DVI-D/HDMI
• Capable of signals up to and including 1080p/60Hz
• Using an adapter, change the output to HDMI
• Compact, 1 RU, 1/3 width size
• Rack mountable, with accessory plate
UXHD CrossPoint allows users to easily integrate analog video and SDI signals into Vaddio’s
ProductionVIEW HD-SDI camera controller/switcher, and can also be used as a stand-alone
video converter. The master control port runs via RS-232 and easily connects to third-party
control systems (AMX, Crestron, etc.) for complete access to the internal functions of the
UXHD CrossPoint. In addition, a Reference input for Genlock is available for synchronizing
the HD-SDI output to an external switcher.
• Converts
DVI Male to HDMI Male HDTV Digital Video Cable
uXHD CrossPoint
North america
999‑5690‑000
International
999‑5690‑001
Connects any HDTV set-top boxes, DTV, DVD, switch or splitter with HDMI to DVI, or
vice versa. Supports uncompressed video and has double shielding for maximum video
performance, prevents screen signal loss and screen ghosting. RoHS Certified.
3.3 ft. Cable
HDtV Digital Video Cable ‑ 3.3 ft.
440‑5643‑001
F e at u r e s
analog video to HD-SDI/SDI
and converts HD-SDI/SDI to analog video
• Video signals include HD component (720p/1080i/1080p),
SD composite and S-Video, and RGBHV up to 1920 x 1200
• Master RS-232 control port allows connection
to third-party control systems
• A Reference input for Genlock is available for
synchronizing the SDI output to an external switcher
• Can be used as a format converter with a loop-thru output
• Converts
10 ft. Cable
HDtV Digital Video Cable ‑ 10 ft.
440‑5643‑003
YPbPr to DVI‑HDMI Converter Configuration
ProductionVIEW DV Capture™
The ProductionVIEW DV Capture is an SD video-to-digital video converter with audio for
both PC and Mac FireWire/1394 enabled computer platforms. DV Capture is the ultimate
tool for capturing and converting live or prerecorded analog video and pro audio feeds into
professional DV format.
Standard definition video inputs include composite video, S-Video and component 480i
video and a 6-Pin FireWire/1394 output. DV Capture can be used with professional audio
mixers and comes equipped with professional level, stereo line inputs on XLR connectors
as well as stereo line level inputs on RCA connectors.
ProductionVIeW DV Capture
North america
999‑5410‑000
International
999‑5410‑001
10
F e at u r e s
use with PC and Mac FireWire/1394 enabled platforms
• Professional Audio I/O
• Flexible Video I/O
• For
Call 800-572-2011 Toll Free
vaddio.com
Studio Console
Studio Console Model SC – 8646
Vaddio’s Studio Console offers exceptional ergonomics, quality construction and the
flexibility to customize for any studio environment. Adjustable tower heights and placement
provide optimized viewing angles and sight lines for full view beyond the console.
Customizable storage and rack spaces, combined with integrated cable management and
proper ventilation make this console ideal for any growing production space.
F E At u r E S
30+ rack spaces
• Two lateral cable management channels
• Strong base, rigid design and steel feet provide ultimate stability
• Back panels easily remove for rear access to equipment
• Ample workspace for laptop or other presentation materials
• Adjustable tower heights and placement options
• Offering
DIMENSIONS
(217.2 cm) W x 29" (736.6 mm) H x 45.75" (116.2 cm) D
• Overall: 85.5"
Base Cabinet Add On Options
Studio Console Packages
The Studio Console comes standard with two base cabinets and console top. A variety of
tower options are available for optimum versatility.
Package 1
•
•
2MidTowers
1LowTower
Package 2
•
•
2HighTowers
1LowTower
Package 3
•
•
2HighTowers
1MidTower
Assembled 799-4010-000
Assembled 799-4020-000
Assembled 799-4030-000
Flat-Packed 799-4010-001
Flat-Packed 799-4020-001
Flat-Packed 799-4030-001
Customized Studio Console Options
Rack Rails
798-0410-000
Doors
Locks
798-0420-000
798-0430-000
Low Tower
*All special configurations are offered upon request. Please contact us at Vaddio:
ToLL FRee 800-572-2011
Call 800-572-2011 Toll Free
vaddio.com
Phone
763-971-4400
Fax
763-971-4464
•
•
13RackUnitSpaces
4.75"(120.7mm)Hx
19.125"(485.78mm)W
x24.75"(628.65mm)D
Mid Tower
•
•
12RackUnitSpaces
14"(355.6mm)Hx
19.125"(485.78mm)W
x20.375"(517.53mm)D
high Tower
•
•
10RackUnitSpaces
16.875"(428.63mm)H
x19.125"(485.78mm)W
x19.125"(485.78mm)D
Customized Studio Console Part Number
Assembled 799-4000-000 Flat-Packed 799-4000-001
11
Studio Consoles
Production Console PC – 5434
Vaddio’s Production Console brings exceptional design, build and versatility to smaller,
more compact studio workspaces. All Vaddio ProductionVIEW units fit directly into a flush
cutout in the console top, resulting in a clean, seamless and organized work area. Also
included is a 10-RU tower providing extra space for additional equipment needs.
DIMENSIONS
54” (137.16 cm) W x 29” (736.6 mm) H x 34” (863.6 mm) D
• Tower 20.5” (520.7 mm) W x 14” (355.6 mm) H x 18.75” (476.25 mm) D
• Console
F E At u r E S
design for smaller studio spaces
• All Vaddio ProductionVIEW units fit flush with console top (8-rack spaces)
• Low profile for optimized viewing angle
• One 10-RU Tower
• Cable management bay
• Metal base with adjustable gliders for stability and portability
• Compact
Production Console PC-5434
Assembled 799-4100-000
Flat-Packed 799-4100-001
Rolling Cart
Short Rolling Cart
The Edge Rolling Cart is a portable rolling rack enclosure with 4" (101.6 mm) twin wheel
casters and black anodized rack rails to fit 18 spaces of rack equipment. The rear panel is
vented for cooling/wiring access.
The Edge Short Rolling Cart is a 12-RU portable rolling rack enclosure designed for use
underneath a desk or table. The black anodized rack rails fit 12 spaces of rack equipment
and the 4" (101.6 mm) twin wheel casters allow for smooth mobility. The rear panel is
vented for cooling/wiring.
rolling Cart MODEL rC-18ru
Assembled 799-0180-000
Flat-Packed 799-0180-001
12
DIMENSIONS
31.5" (800.1mm) H x 19.125" (485.8mm) W x
17.25" (438.15mm) D (to the rails)
• Total Height 37.5" (952.5mm)
• Internal
Short rolling Cart MODEL rC-12ru
Assembled 799-0120-000
Flat-Packed 799-0120-001
DIMENSIONS
21" (53.3 cm) H x 19.125" (485.8mm) W x
17.25" (438.15mm) D (to the rails)
• Total Height 28" (711.2mm)
• Internal
Call 800-572-2011 Toll Free
vaddio.com
Racks
ProductionVIEW Rack Enclosure
ProductionVIEW Rack Console
The ProductionVIEW Rack Enclosure is a dual-bay rack mounting system with an 8-RU
upper bay and a 5-RU lower bay. The lower rack bay fits large HD switchers/mixers,
including the ProductionVIEW console suite of products, while the upper rack bay fits a
variety of rack mount equipment up to 18 inches deep.
The ProductionVIEW Rack Console is a dual-bay, slant-top rack mounting system with
an 8-RU upper bay and a 7-RU lower bay. The lower rack bay fits the ProductionVIEW
line of consoles, while the upper rack bay fits a variety of rack mount equipment up
to 14 inches deep.
F E At u r E S
Upper bay
• 7-RU Lower bay
• Heavy-duty aluminum construction
• Attractive black powder coat finish
Made of heavy gauge aluminum, the back panel has wire tie slots and holes for mounting
the enclosure to a tabletop. The black powder coat finish is durable and long lasting.
• 8-RU
F E At u r E S
Upper bay
• 5-RU Lower bay
• Heavy-duty aluminum construction
• Attractive black powder coat finish
• Holes for mounting multiple enclosures
to each other
• 8-RU
**Drawer not included
ProductionVIEW rack Console
998-5000-100
ProductionVIEW rack Enclosure
998-5000-200
Precision Camera Controller Rack Drawer
ProductionVIEW Rack Enclosure Drawer
The ProductionVIEW Precision Camera Controller Rack Drawer includes a sliding shelf and
controller mounting bracket kit for a ProductionVIEW Precision Camera Controller to be
easily stored. This accessory can also be used with other third-party rack systems.
The ProductionVIEW Rack Enclosure Drawer includes a sliding shelf and controller
mounting bracket kit for ProductionVIEW FX, HD, HD-SDI , HD MV or HD-SDI MV consoles
to be easily stored. This accessory can also be used with other third-party rack systems.
F E At u r E S
slide-out drawer
• Mounting hardware for ProductionVIEW
series switchers/controllers*
• Locking
* ProductionVIEW HD not included
ProductionVIEW
rack Enclosure Drawer
998-5000-210
Precision Camera Controller
rack Drawer
998-5000-211
F E At u r E S
slide-out drawer
• Mounting hardware
for Precision Camera Controller*
• Locking
* Precision Camera Controller not included
ProductionVIEW Rack Mount Ears
Precision Camera Controller Rack Mount Ears
6-RU Rack Mount Ears attach to the
sides of any ProductionVIEW (not
including Precision Camera Controller)
for mounting into system racks or
ProductionVIEW Rack Consoles.
ProductionVIEW
rack Mount Ears
998-5000-001
Call 800-572-2011 Toll Free
4-RU Rack Mount Ears attach to the
sides of the ProductionVIEW Precision
Camera Controller for mounting into
system racks of ProductionVIEW Rack
Consoles.
Precision Camera Controller
rack Mount Ears
998-5000-002
vaddio.com
13
Monitors
TeleTouch™ 18.5" HD Touch Screen
Rack Mount LCD Monitor
TeleTouch 22" HD Touch Screen LCD
Monitor with Base
The TeleTouch 18.5" HD Touch Screen Rack Mount LCD Monitor works in conjunction with
the ProductionVIEW HD MV & HD-SDI MV with built-in multiviewer. The touchscreen allows
all presets and camera positions to be displayed and activated by touching the image
itself. The multiviewer can be configured to display up to six input windows and two larger
“Preview” and “Program” windows with red and green tally window borders. In addition,
each camera input can have up to 12 stored “video thumbnail” preset camera shots.
The TeleTouch 22" Touch Screen LCD Monitor with base works in conjunction with the
ProductionVIEW HD MV & HD-SDI MV with built-in multiviewer. The touchscreen allows
all presets and camera positions to be displayed and activated by touching the image
itself. The multiviewer can be configured to display up to six input windows and two larger
“Preview” and “Program” windows with red and green tally window borders. In addition,
each camera input can have up to 12 stored “video thumbnail” preset camera shots.
F E At u r E S
and 1080p/50 input resolutions
• 18.5-inch diagonal resistive touch screen surface
• Integrated Rack Mount Enclosure
• DVI and RS-232 cables included
• Worldwide power cord set included (North America, Euro & UK)
F E At u r E S
and 1080p/50 input resolutions
• 22-inch diagonal resistive touch screen surface
• DVI and RS-232 cables included
• Worldwide power cord set included (North America, Euro & UK)
• 1080p/60
teletouch 18.5" HD touch Screen
rack Mount LCD Monitor
999-5520-185
• 1080p/60
teletouch 22" HD touch Screen LCD Monitor with Base
999-5520-022
PreVIEW Dual 6.4 LCD Rack Mount Monitor
PreVIEW HD Dual 7.0 LCD Rack Mount Monitor
™
The Vaddio PreVIEW HD Dual 7.0 features two 7-inch (17.78cm) 1.2 megapixel high
definition LCD monitors for exceptional video clarity and color handling.
The Vaddio PreVIEW Dual 6.4 features two 6.4-inch (16.26cm) standard definition active
matrix LCD monitors for exceptional video clarity and color handling. The PreVIEW Dual
6.4 comes equipped with two 960 x 234 resolution LCDs for previewing details and has
brightness, contrast and color controls for fine-tuning the video display.
The native widescreen displays have an internal menu to adjust each monitor’s settings,
which include brightness, contrast, color, tint, sharpness and several other advanced
options. In addition to SD, HD and S-video inputs, with active loop-thru outputs, there is
also an analog RGB input on a VGA connector.
PreVIEW Dual 6.4 LCD
rack Mount Monitor
NA and INtL
999-5500-002
PreVIEW HD Dual 7.0 LCD
rack Mount Monitor
NA and INtL
999-5510-012
F E At u r E S
Native 16:9 LCD screens, VGA input
• Component, S-Video and composite inputs,
with loop-thru outputs
• Color, contrast, brightness, sharpness
and On/Off controls per LCD and tally indicators
• 3-RU Rack enclosure with tilt mechanism
•
F E At u r E S
Active matrix 960 x 234 LCD screens
Two inputs with active looping outputs on BNCs
• Color, contrast, brightness and On/Off controls per LCD
• 3-RU Rack enclosure with tilt mechanism
•
•
PreVIEW Triple 5.6 LCD Rack Mount Monitor
The Vaddio PreVIEW Triple 5.6 features three 5.6-inch (14.22cm) standard definition active
matrix LCD monitors for exceptional video clarity and color handling. The PreVIEW Triple
5.6 comes equipped with three 480 x 234 resolution LCDs for previewing details and has
brightness, contrast and color controls for fine-tuning the three video displays.
PreVIEW HD Triple 5.0 LCD Rack Mount Monitor
The Vaddio PreVIEW HD Triple 5.0 features three 5-inch (12.7cm) 1.2 megapixel high
definition LCD monitors for exceptional video clarity and color handling.
The native widescreen displays have an internal menu to adjust each monitor’s settings,
which include brightness, contrast, color, tint, sharpness and several other advanced
options. In addition to SD, HD and S-video inputs, with active loop-thru outputs, there is
also an analog RGB input on a VGA connector.
PreVIEW triple 5.6 LCD
rack Mount Monitor
NA and INtL
999-5500-003
F E At u r E S
matrix 480 x 234 LCD screens
• Three inputs with active looping outputs on BNCs
• Color, contrast and brightness controls per LCD
• 3-RU Rack enclosure with tilt mechanism
• Active
PreVIEW Quad 4 LCD Rack Mount Monitor
PreVIEW HD triple 5.0 LCD
rack Mount Monitor
NA and INtL
999-5510-013
14
F E At u r E S
Native 16:9 LCD screens VGA input
Component, S-Video and composite inputs,
with loop-thru outputs
• VGA Input
• Color, contrast, brightness, sharpness
and On/Off controls per LCD and tally indicators
• 3-RU Rack enclosure with tilt mechanism
•
The Vaddio PreVIEW Quad 4 features four 4-inch (10.16cm) standard definition active
matrix LCD monitors for exceptional video clarity and color handling. The PreVIEW Quad
4 is a simple and straightforward four LCD rack mount monitor without controls for
previewing general shots and areas where extreme detail is not needed.
•
PreVIEW Quad 4 LCD
rack Mount Monitor
NA and INtL
999-5500-004
F E At u r E S
Active matrix 480 x 234 LCD screens
Four inputs with active looping outputs on BNCs
• 2-RU Rack enclosure with tilt mechanism
•
•
Call 800-572-2011 Toll Free
vaddio.com
a Camera Tracking System
1
Learn
It is important to consult with the customer regarding
how the room is going to be used, and where the
tracking system will be implemented.
You need to clearly understand:
What are the end user’s expectations and needs?
Understand the boundaries and how the presenter
will move about during the presentations.
Your room dimension and layout, windows, doors, etc.
• Make a detailed drawing of the room,
showing doors and windows.
• If possible, visit and confirm the drawing by
scouting out the room.
• Check for possible infrared and/or motion sources
in the tracking area.
If the system requires High Definition or Standard
Definition quality video:
• Note the Installation requirements, cabling, power,
audio, etc.
2
Measure
On the room drawing determine:
• The width (W) of the tracking area where
the presenter will move.
• Locate items that could interfere or obstruct
the camera view such as projectors.
• Cameras are located to allow a proper view of
the presenter.
AutoTrak System Configuration
Call 800-572-2011 Toll Free
vaddio.com
Choose the suitable camera model based on
viewing angle of the presentation area and
camera locations. Use the calculator by going to:
www.vaddio.com/tech-center.php and download
our PTZ Image Size Calculator.
3
4
Decide
Compare both systems and choose based on:
TrackVIEW
• Allows for only one person in the presentation
area.
Confirm
• The presenter must be visible in the wide viewing
Windows and/or doors are not in the tracking area.
Tracking system is not too low and may be blocked
by attendees.
Camera is not installed too high. Avoid steep viewing
angles.
• When zooming in, make sure to keep an
appropriate shot – preferably at least mid-thigh to
above the presenter's head.
• Make sure there is enough headroom for all
presenters – tall and short – who will be utilizing
the room.
• Harsh lighting should not be present in the
presentation area.
• Uniform lighting of more than 100 lux is
recommended, especially if HD is used.
• There are no IR sources (incandescent light,
sunlight, etc) in the presentation area.
(AutoTrak only)
• There is no motion in the presentation area other
than the presenter. Avoid projection screens that
reach the floor. (TrackVIEW only)
range of the reference camera.
• Maximum distance from presenter is 80 feet SD
and 60 feet HD depending on camera choice.
• Maximum cable length is 200 feet.
• Accepts triggers directly and control from third
party such as AMX and Crestron.
AutoTrak
• Multiple persons can be on stage, but only one can
be tracked.
• AutoTrak IR emitter (lanyard) must be in plain view
of the IR reference camera.
• Maximum distance from presenter to camera is
40 feet in SD or HD at all times.
• Maximum cable length is 100 feet.
• If triggers and presets are needed, a Vaddio
AutoPresenter is required.
** All Vaddio tracking camera systems must be
programmed by either a Vaddio Certified Installing
Technician, or Vaddio Factory Technician.
(See 999-PROG-000)
** Integrators MUST complete the Online Certification
Tutorial to submit a PO, specify and design Vaddio
Tracking Systems.
**For more information on Camera Tracking
Certification, visit our website at www.vaddio.com
TrackVIEW System Configuration
15
Automated Content Presentation System
AutoTrak is an IR lanyard-based camera tracking system designed to provide a smooth and accurate panning
motion that follows the instructor as they walk around the presentation area of a classroom. AutoTrak is Vaddio’s
revolutionary automated camera tracking system designed for educational and corporate training facilities.
The instructor wears a lanyard belt pack that emits infrared light received
by an IR PTZ camera. Video is then sent from the IR PTZ camera to the
Tracking Camera. The result is a smooth, accurate panning motion that
follows the instructor as they walk around the presentation area of the
classroom. AutoTrak eliminates the need for a staff person to operate
a camera in a classroom to follow the instructor as they conduct class.
of products, including streaming devices, lecture capture systems or
videoconferencing codecs.
Both the IR camera and the tracking camera are based on Vaddio’s
single-chip CCD ClearVIEW HD-18 high definition PTZ camera. The
system can deliver both standard definition and high definition video
from the tracking camera. The video output can then be fed into a variety
** Integrators MUST complete the Online Certification Tutorial to submit a PO, specify and
design Vaddio Tracking Systems.
AutoTrak™ with Audio Interface
AutoTrak – No Audio Interface
Simply slip the lanyard around your neck and the system begins to track,
freeing teachers to do what they do best: teach.
** All Vaddio tracking camera systems must be programmed by either a Vaddio Certified
Installing Technician, or Vaddio Factory Technician. (See 999-PROG-000)
**For more information on Camera Tracking Certification, visit our website at
www.vaddio.com
The system can deliver both standard definition and high definition video from the tracking
camera. The video output can then be fed into a variety of products including streaming
devices, lecture capture systems or videoconferencing codecs.
The system can deliver both standard definition
and high definition video from the tracking
camera without the audio option. The video
output can then be fed into a variety of products
including streaming devices, lecture capture
systems or videoconferencing codecs.
AutoTrak Rack Panel Front
IR
Reference
Camera
F E At u r E S
HD-18 SR IR Camera
• One WallVIEW HD-18 SR (Tracking Camera)
• One IR lanyard with integrated wireless microphone and
belt pack with belt clip
• One AutoTrak Camera Tracking Interface
• One Dual HD-18 Wall Mounting Bracket
• One WallVIEW
AutoTrak Audio Rack Panel Interface
Autotrak — No Audio Interface
North America 999-7205-000
International 999-7205-001
AutoTrak with DVI/HDMI and Audio Interface
Tracking
Camera
AutoTrak IR Lanyard
F E At u r E S
HD-18 SR IR Camera
• One WallVIEW HD-18 SR (Tracking Camera)
• One IR lanyard with integrated wireless microphone and
belt pack with belt clip
• One AutoTrak Audio Interface
• One AutoTrak Camera Tracking Interface
• One Dual HD-18 Wall Mounting Bracket
The system can deliver both high definition
(YPbPr) and digital video (DVI-D or HDMI) from the
tracking camera.
• One WallVIEW
Autotrak with Audio Interface
North America Only
999-7200-000
Autotrak System Configuration
F E At u r E S
Quick-Connect DVI/HDMI SR Interface
• One WallVIEW HD-18 DVI/HDMI IR Camera
• One WallVIEW HD-18 DVI/HDMI (Tracking Camera)
• One IR lanyard with integrated wireless microphone and
belt pack with belt clip
• One AutoTrak Audio Interface
• One AutoTrak Camera Tracking Interface
• One Dual HD-18 Wall Mounting Bracket
• One
Autotrak with DVI/HDMI
and Audio Interface
North America Only
999-7210-000
AutoTrak with DVI/HDMI – No Audio Interface
The system can deliver both high definition
(YPbPr) and digital video (DVI-D or HDMI) from the
tracking camera.
F E At u r E S
Quick-Connect DVI/HDMI SR Interface
• One WallVIEW HD-18 DVI/HDMI IR Camera
• One WallVIEW HD-18 DVI/HDMI (Tracking Camera)
• One IR lanyard with integrated wireless microphone and
belt pack with belt clip
• One AutoTrak Audio Interface
• One AutoTrak Camera Tracking Interface
• One Dual HD-18 Wall Mounting Bracket
• One
Autotrak with DVI/HDMI
— No Audio Interface
North America
999-7215-000
International
999-7215-001
16
Call 800-572-2011 Toll Free
vaddio.com
Automated Content Presentation System
TrackVIEW is an automated camera tracking system that incorporates both motion-based camera tracking and
camera preset technology to track the presenter at the front of the room.
Designed as a two-camera system, one camera is the reference
camera, which frames the whole presentation area, while
the second camera is the tracking camera, which responds to
presenter movement within the reference area.
trackVIEW 70 System Configuration
TrackVIEW can track motion, allowing the presenter to stay on camera
while walking between preset camera shots.
The EZCamera system built-in to the TrackVIEW module provides power
and control, while returning video from the PTZ camera over a single Cat. 5
cable. Other features include first step, last step and multi-step modes for
programming the preset triggers for priority and for multi-trigger wide
shots, and a USB or RS-232 port for setting up the TrackVIEW system
software.
TrackVIEW™ HD1 System
The TrackVIEW HD1 System features the Sony
EVI-D70 camera with a wide-angle lens for the
reference camera and the Sony EVI-HD1 for the
tracking camera.
trackVIEW 70 Coverage Angles
SYStEM INCLuDES
trackVIEW HD1
NtSC
999-7000-630
PAL
999-7000-631
One Sony EVI-D70 PTZ camera with
EZCamera Cable Shoe and wide-angle lens
(reference camera)
• One Sony EVI-HD1 PTZ camera with
EZCamera Cable Shoe and Quick-Connect PRO
(tracking camera)
•
TrackVIEW 70 System
The TrackVIEW 70 System features the Sony
EVI-D70 cameras for both the reference and
tracking camera.
SYStEM INCLuDES
Sony EVI-D70 PTZ camera with EZCamera
Cable Shoe and wide-angle lens (reference camera)
• One Sony EVI-D70 PTZ camera with EZCamera
Cable Shoe (tracking camera)
• One
trackVIEW 70
NtSC
999-7000-070
PAL
999-7000-071
TrackVIEW 100 System
The TrackVIEW 100 System features the Sony
EVI-D70 for the reference camera with a
wide-angle lens, and the Sony EVI-D100 for the
tracking camera.
trackVIEW 100
NtSC
999-7000-100
PAL
999-7000-101
Call 800-572-2011 Toll Free
vaddio.com
SYStEM INCLuDES
Sony EVI-D70 PTZ camera with EZCamera
Cable Shoe and wide-angle lens (reference camera)
• One Sony EVI-D100 PTZ camera with EZCamera
Cable Shoe (tracking camera)
• One
17
an Automated Content Presentation System
1
Content
Select the content that will be used by the presenter
•
•
•
•
•
PC
Whiteboard
Recorded Video (DVD)
Document Camera
Video Conferencing Far End Video
2
Work Area
Locate the presenter’s work areas
• Podium
• Whiteboard
• Teaching Station
• Desk/Table
3
Triggers
Select the type of triggers to be used at each work
area
• PresenterPOD
• StepVIEW Mat - Floor Mat
• AutoVIEW IR - Ceiling IR
• TouchVIEW Buttons
• MicVIEW
Note*A PresenterPOD is required if you plan on using more
than one source, or if you want to activate both a camera
and a content source at the same time.
4
Presentation Content
Select what content will need to be available at each
workstation (up to two per PresenterPOD)
• Podium - i.e. PC & Document Camera
• Whiteboard – i.e. Whiteboard & PC
• Teaching Desk – Far-end Video, Document Camera
Note* With each PresenterPOD you can automate up to
two content sources per PresenterPOD. For example, at the
podium you can have your content preset be a PC showing
a presentation as one of the buttons designated on the
PresenterPOD. The other button on the PresenterPOD can
be designated for a different video source, such as a ceiling
document camera. When either button on the PresenterPOD
is pressed, the designated video input (PC or DocCam) will
appear to the viewers of the presentation.
Note**Camera tracking system solutions may be added for
overall design options. Please see page 15 for more details.
5
Presenter Camera
Select what Presenter Cameras are to be used in
the room and what presenter shot is desired at each
workstation.
• Main presenter camera with presets
• Tracking camera system
• Side room cameras
Note* Side room cameras are positioned cameras between
30-45 degrees from the center of the room and allow for
preset camera shots of the presenter walking towards or
away from the camera, while a center facing camera alone
can only show a side profile of the presenter.
6
Display
Will you need to show both the presenter and
content from other sources – document camera,
Squiggle Board, computer, etc. – on the video output
simultaneously?
7
Microphone Count
Is student camera automation required?
If so, select how many student cameras you will
need to cover the students sitting in the classroom,
then determine the number of microphones that will
be used to pick up the audio of the students. The
microphone count is important as each microphone
will be used as a camera preset trigger device
that is activated when they use the push-to-talk
button on the microphone. These microphones
are then connected to MicVIEW, which provides
a true microphone switching circuit that provides
constant contact triggers to the AutoPresenter. This
eliminates the erratic switching that occurs with a lot
of microphone mixers that use fast gating or allow
multiple microphones to stay on.
8
Classroom Display
Select your classroom display layout keeping in mind
that the instructor will need at least one monitor
at the back of the room as a confidence monitor,
allowing them to view what video source is being
recorded or displayed to the remote viewers.
You have now designed a fully automated content
presentation system. If you need any additional help
with your design please contact our Support Staff is
available to help with your design requirements.
If so, each trigger device can be programmed to
either have a picture-in-picture or not.
Automated Education Configuration
18
Call 800-572-2011 Toll Free
vaddio.com
Automated Content Presentation Systems
Vaddio’s AutoPresenter is designed to make it easier to present and create content in the classroom by combining
the automation of people and content in one easy-to-use technology.
AutoPresenter™
PresenterPOD™
The AutoPresenter can switch up to six video inputs in analog component HD
(720p/1080i/1080p), RGBHV (up to 1920 x 1200) and SD video (NTSC and PAL). Individual
video transitions including fades, wipes and dissolves can be programmed as required,
while each video input can be up/down converted to create a common aspect ratio and
resolution. An additional output converter will convert YPbPr component video to a DVI/
HDMI digital output for integrating with TANDBERG and Polycom codecs. The AutoPresenter
allows the presenter to automate up to 72 predetermined presets for any type of content
(video, document camera, whiteboard, PC, etc.). The PIP option allows any of these types
of content to be shown at five different screen positions, in three different sizes within each
preset and can be controlled with a PresenterPOD.
The PresenterPOD is the perfect complement to the Vaddio AutoPresenter and ControlVIEW
XHD video switcher/automated camera control systems. The PresenterPOD has two
large buttons located on the POD to offer flexible control over the automated content and
other necessary content sources. A third, small square button is available for PIP on/off
adjustments if picture-in-picture (PIP) is stored within any of the presets activated when
used in conjunction with the AutoPresenter, which features PIP function.
AutoPresenter
North America
999-5675-000
International
999-5675-001
F E At u r E S
up to six cameras and stores 72 camera presets
internally
• Six-port automatic video switcher
• Transitions include cut, cross fade or a variety of wipes
from .01 to 4.0 seconds
• Connects to Vaddio Precision Camera Controller
via Link Ports
• Master RS-232 Control Port
• Compatible with Vaddio, Panasonic, Sony
and Canon robotic PTZ cameras
• PIP can be arranged in five different positions,
in three different sizes
• Controls
AutoPresenter Configuration
AutoPresenter allows individual triggers to be set up to either show a picture-in-picture
(PIP) or a single video source.
With the use of a PresenterPOD,
the PIP may be turned on and off
from specific pre-programmed
presets, by the push of a button PresenterPOD Interface (Rear)
PresenterPOD Interface
on the POD.
PresenterPOD
North America
999-1111-000
International
999-1111-001
The PresenterPOD connects via a single Cat. 5 cable
to the Presenter POD Interface for power and data.
The Interface can be programmed for either latching
or momentary triggers.
F E At u r E S
four buttons can be programmed for either momentary
or latching type triggers
• The PresenterPOD Interface can support up to two PODs
• Each kit contains one PresenterPOD and one Interface –
additional PODs are sold separately
• Adhesive labels and mounting hardware for POD included
• All
Additional PresenterPOD
998-1111-002
PresenterPOD Configuration
Note: This configuration shows the PresenterPOD System, with an additional POD,
which is sold separately.
Call 800-572-2011 Toll Free
vaddio.com
19
Automated Content Presentation Systems
ControlVIEW XHD is a multi-input seamless PTZ control system with HD, RGBHV and SD video switching, video
transitions and camera preset functionality designed for a variety of training and videoconferencing applications.
ControlVIEW™ XHD PTZ Camera Control System
ControlVIEW XHD - Live Event Production Configuration
ControlVIEW XHD is a presenter-controlled seamless switcher with built-in camera
preset triggers. It can be used in a variety of applications such as live event production,
videoconferencing, distance education and many others.
ControlVIEW XHD is an automatic camera control system designed to control up to six PTZ
cameras (or other video sources) and assign up to 72 total camera preset positions. The
ControlVIEW XHD 6 x 1 switcher accepts analog SD, HD and RGBHV signals on all inputs,
and can up/downscale these signals to dual program outputs at either an SD, HD or RGBHV
resolution.
The system works with a variety of PTZ cameras in the Vaddio line. Input trigger
accessories that work with ControlVIEW XHD include Vaddio PresenterPOD, TouchVIEW
RF buttons, StepVIEW Mats, AutoVIEW IR Sensors and MicVIEW, as well as other thirdparty contact closure devices. Simply program a trigger device, such as a StepVIEW Mat,
to a preset camera pan/tilt/zoom position. When an instructor walks onto the StepVIEW
Mat, ControlVIEW XHD moves the camera to the programmed camera position, and then
switches to that camera.
ControlVIEW XHD can also be connected directly to a Precision Camera Controller for a
low-cost HD switcher/camera controller package.
ControlVIEW XHD
PtZ Camera Control System
North America
999-5672-000
International
999-5672-001
F E At u r E S
up to six cameras
and stores 72 camera presets internally
• Six-port automatic or manual video switcher
• Transitions include cut, cross fade or a variety of wipes
• Connects to Vaddio Precision Camera Controller
via Link Ports
• Master RS-232 Control Port
• Compatible with Vaddio, Panasonic,
Sony and Canon robotic PTZ cameras
• Controls
Executive Boardroom Configuration
20
Call 800-572-2011 Toll Free
vaddio.com
Automated Content Presentation Systems
Vaddio’s Squiggle Video Whiteboard eliminates the need to aim fixed or PTZ cameras at a presentation. The Suiggle
Board offers presenters a clear, creative outlet for capturing traditional classroom content in HD or SD video outputs.
Squiggle™ Board
Squiggle Board 4 x 6 feet
(1.22m x 1.83m)
North America
999-5446-000
International
999-5446-001
Squiggle Board 4 x 8 feet
(1.22m x 2.03m)
North America
999-5448-000
International
999-5448-001
Squiggle Board Stand
The Squiggle Board can be used in a variety of
applications from videoconferencing, content
creation, IMAG, rich media systems or in any system
designed to incorporate a whiteboard as a video
input device. Because no dedicated PC is required,
Vaddio’s Squiggle Board is compatible with any
videoconferencing, TelePresence, distance education
or video media distribution system. In addition to HD/
SD outputs, data can be captured and stored as a
JPEG image onto any USB flash drive.
Using Vaddio’s EZCamera Cabling System, power
and USB data are run over a single Cat. 5 cable
up to 100 feet from the whiteboard to the Video
Whiteboard Quick-Connect Interface. The Video
Whiteboard Interface interprets the data and
outputs high definition DVI-D or HDMI (HDMI with
cable adapter) digital video and high definition
YPbPr analog component video at resolutions of
720p/59.94Hz and 720p/50Hz, or standard definition
video at 480i/29.97Hz and 576i/25Hz.
The Squiggle Board includes the Video Whiteboard
Quick-Connect Interface, one black marker, one
digital marker sleeve and one electronic eraser.
The Squiggle Board Stand is an easy-to-construct
framing system that securely holds the 4' x 6'
(1.22m x 1.83m) or 4' x 8' (1.22m x 2.03m)
whiteboard. It includes casters for portability and is
extremely heavy duty.
F E At u r E S
and upright support rails for secure framing
• Stand base with casters for portability
• Top, middle
Squiggle Board Stand 4'x6' 998-5446-600
Squiggle Board Stand 4'x8' 998-5448-800
Colored Digital Marker Sleeves
Digital Marker Sleeves
998-5440-030
Replacement Bullet Tip Markers
F E At u r E S
INCLuDES
• Red, Green, Blue
• Stand-alone
Digital Control Panel
video appliance - no computer required
• Outputs four colors (black, blue, red and green)
against a white background (blue, green and red markers
optional)
• HD video resolutions of 720p/59.94, 720p/50 and SD
resolutions of 480i/29.97 and 576i/25
• Features three-line thicknesses
and an Erase All function
• One-Touch Image Save allows USB drive to capture
drawings as JPEG images
• Comes in two sizes: 4′ x 6′ and 4′ x 8′
• Completely compatible with all
Vaddio Automated Content Presentation Systems
INCLuDES
Red Pen Sleeve with batteries
• 1 Blue Pen Sleeve with batteries
• 1 Green Pen Sleeve with batteries
• 1 Red, bullet tip whiteboard marker
• 1 Blue, bullet tip whiteboard marker
• 1 Green, bullet tip whiteboard marker
• 1
and Black bullet tip markers
replacement Bullet tip Markers
998-5440-040
Standard Whiteboard Eraser
INCLuDES
Eraser
• 1 Whiteboard
Standard Whiteboard Eraser
998-5440-010
Whiteboard Cleaner
INCLuDES
Cleaner
• 1 Whiteboard
Whiteboard Cleaner
998-5440-020
Squiggle Board System Configuration
Squiggle Board in Corporate Environment
Call 800-572-2011 Toll Free
vaddio.com
21
Automated Content Presentation Systems
Squiggle Kit
Squiggle IP Software Module
Capable of being installed alongside almost any existing whiteboard, the Squiggle Kit
converts whiteboard notes into an HD or SD video signal. Because no dedicated PC is
required, the video signal can then be connected to any videoconferencing, TelePresence,
distance education or video media distribution system. In addition to HD/SD outputs, data
can be captured and stored as a JPEG image into any USB flash drive.
By adding the Squiggle IP Software Module, the existing Squiggle Board Systems now have
the ability to stream live video. In addition to live streaming, Squiggle IP enables remote
JPEG image capture and end-user/administrator controls. End-user controls include
marker color and tip size, eraser size, battery status and capture settings. Administrators
have the additional ability to control security, network, time/date and streaming settings.
These functions are accessible by any computer browser, as well as any iOS or Android
portable device.
The portable EZTub, with Digital Control Panel, screws into the wall on the left side of the
whiteboard. Based on the same concept as the Vaddio Squiggle Board system, the Squiggle
Kit uses the same technology to run power and USB data over a single Cat. 5 cable up to
100 feet (30.5m) from the whiteboard to the Video Whiteboard Quick-Connect Interface.
The Quick-Connect is located at the head-end for plugging into your video device. Outputs
include high definition DVI-D or HDMI (HDMI with cable adapter) digital video and high
definition YPbPr analog component video at resolutions of 720p/59.94Hz and 720p/50Hz,
or standard definition video at 480i/29.97Hz and 576i/25Hz.
The Squiggle Kit includes the EZTub with Digital Control Panel, Video Whiteboard
Quick-Connect Interface, one black marker, one digital marker sleeve and one electronic
eraser.
F E At u r E S
EZTub with Digital Control Panel can be installed
alongside almost any existing whiteboard
• Stand-alone video device - no computer required
• Outputs four colors (black, blue, red and green) against a
white background
• HD video resolutions of 720p/59.94, 720p/50 and SD
resolutions of 480i/29.97 and 576i/25
• Features three-line thicknesses and an Erase All function
• One-Touch Image Save allows USB drive to be attached to
Digital Control Panel Interface to capture drawings as JPEG
image
• Completely compatible with all Vaddio Automated Content
Presentation Systems
Password control for
User and Admin
Save JPEG images to local USB flash
drive or specify remote directory
Choose a color by using the color picker or
by specifying a hexadecimal value
User screen allows control of markers,
eraser, capture settings, snapshot and
logout. View battery status of each
electronic marker and eraser.
• Portable
Squiggle Kit
North America
999-5441-000
International
999-5441-001
Squiggle Kit System Configuration
Squiggle IP Software Module
998-5449-010
F E At u r E S
monitor status of electronic marker sleeves
• Remotely change marker color and tip size
• Remotely change electronic eraser size
• Save JPEG image to local flash drive or remote directory
• Place customized background images for copyright and
watermarking of video feeds/images
• Date and time provides synchronization to Internet time
servers or through manual override
• DHCP or fixed addressing in IPV4 networks
• RTSP compliant video streaming for up to four connections
• HTTP snapshot of remote whiteboard content
• Modify credentials for user and admin
• Remotely
Squiggle Board output on Safari web browser
22
Call 800-572-2011 Toll Free
vaddio.com
Automated Content Presentation Systems
Triggers for Preset Controllers work with any of Vaddio’s Automated Content Presentation Systems including
AutoPresenter, ControlVIEW XHD, TrackVIEW and AutoTrak.
PresenterPOD
MicVIEW™ 12 Input Teleconference Microphone Switcher/Mixer
The PresenterPOD is the perfect complement to the Vaddio AutoPresenter and ControlVIEW
XHD video switcher/automated camera control systems. The PresenterPOD has two
large buttons located on the POD to offer flexible control over the automated content and
other necessary content sources. A third, small square button is available for PIP on/off
adjustments if picture-in-picture (PIP) is stored within any of the presets activated when
used in conjunction with the AutoPresenter, which features PIP function.
Vaddio’s MicVIEW is an automated 12-input microphone switcher/mixer designed to
integrate with Vaddio’s Automated Content Presentation Systems.
The PresenterPOD connects via a single Cat. 5 cable
to the Presenter POD Interface for power and data.
The Interface can be programmed for either latching
or momentary triggers.
F E At u r E S
four buttons can be programmed for either momentary
or latching type triggers
• The PresenterPOD Interface can support up to two PODs
• Each kit contains one PresenterPOD and one Interface additional PODs are sold separately
• Adhesive labels and mounting hardware for POD included
• All
PresenterPOD
North America
999-1111-000
International
999-1111-001
MicVIEW
North America
999-0001-000
International
999-0001-001
F E At u r E S
• 12 Trigger/Logic
outputs for use with ControlView XHD,
ProductionView and AutoPresenter systems
• Link up to eight mixers for 96 channels
• Designed for use with 3-wire
Unidirectional Boundary Microphone
Unidirectional Boundary Microphone
Audio-Technica® AT U891R Boundary Microphone for MicVIEW
unidirectional
Boundary
Microphone
701-0001-891
F E At u r E S
LED indicates when mic is on
• Assignable switch for operation (touch on/off/mom)
• 25 foot (7.6m) detachable cable; TA3F to XLR-M type
• Red
6 – Channel Microphone Extension Snake for MicVIEW
Additional PresenterPOD
PresenterPOD Interface
PresenterPOD Interface (Rear)
998-1111-002
Rack Panel PresenterPOD Interface
This optional rack panel is compatible with the PresenterPOD Interface. The Rack Panel is
drilled out to hold up to two PresenterPOD Interfaces on a 1-RU panel. It fits into a standard
19-inch rack mount enclosure.
for AutoPresenter, ControlVIEW XHD and ProductionVIEW
Includes four TouchVIEW RF remote control transmitter buttons and one TouchVIEW Receiver
F E At u r E S
RF remote control button transmitters
with 62 unique program frequencies
• One RF receiver, capable of receiving four
remote control buttons
• Expandable to 12 wireless remote controls
by using three receivers
• Four
International
999-1201-001
TrackVIEW System Programming
TrackVIEW System Programming includes a single day of on-site programming and training
of TrackVIEW system by certified Vaddio technical staff.
trackVIEW System Programming
999-PrOG-000
The AutoVIEW IR Sensor, a single ceiling-mounted IR sensor for use with the AutoVIEW IR
System, allows the use of up to eight additional AutoVIEW IR sensors per system.
International
999-1701-101
TouchVIEW™ Wireless Remote Control System
NOtE: travel expenses additional
F E At u r E S
XLR-F snake box to six shielded pair wires
• Snake length: 25 feet (7.6m)
• Six
AutoVIEW™ IR Sensor
AutoVIEW Ir Sensor
North America
999-1701-100
rack Panel PresenterPOD Interface
998-6000-003
touchVIEW
North America
999-1201-000
Microphone
Extension Snake
999-3000-006
F E At u r E S
IR sensor and acrylic lens cover
• AutoVIEW IR Interface Controller
and PowerRite™ power supply
• One 3 foot (.9m) Cat. 5 patch cable
• Active
StepVIEW™ Mat – Small Exposed
The StepVIEW presence sensing mats come in a rubberized, non-slip exposed auto locator
mat for permanent installation. All trigger mats are durable, attractive and come in two
different sizes for flexibility of mat positioning.
Presence-Sensing Automatic Locator Mat
44 inches (1.12m) x 27.5 inches (70cm)
StepVIEW Mat - Small Exposed
North America 999-1501-000
International 999-1501-001
StepVIEW Mat – Large Exposed
The StepVIEW presence sensing mats come in a rubberized, non-slip exposed auto locator
mat for permanent installations. All trigger mats are durable, attractive and come in two
different sizes for flexibility of mat positioning.
Presence-Sensing Automatic Locator Mat
57 inches (1.45m) x 27.5 inches (70cm)
StepVIEW Mat - Large Exposed
North America 999-1502-000
International 999-1502-001
Call 800-572-2011 Toll Free
vaddio.com
23
a High Definition PTZ Camera System
Depending on your project requirements —
whether it is for a broadcast, professional A/V or
videoconference application — our selection of
cameras and accessories should provide you with
the type of format that your project requires.
1
3-Chip vs. Single-Chip
3-chip cameras have historically given the best
quality images; since the incoming light is divided
into red, green and blue then processed, the resulting
output signal becomes the sharpest, most vibrant
color image.
Presently single CMOS imager cameras are capable
to provide better than 3 chip top quality highdefinition images, at a lower price point. Compared
with 3-chip cameras, single CMOS cameras are
significantly smaller, and consume less power. There
are a wide variety of single-chip HD cameras that
Vaddio carries, for virtually any type of application.
2
CMOS or CCD
Traditional CMOS image sensors require more light
than comparably sized CCD image sensors. However,
the latest CMOS image sensors – the Exmor™ series
– use the latest technological advancements to reach
a superior light gathering capability when compared
with CCD sensors. Vaddio’s HD-20 PTZ camera is
designed around the Exmor™ sensor technology.
This is the most important aspect of a camera sensor,
especially when low light situations are present in
the area that you need to install PTZ cameras.
3
Optical Zoom & Angle of View
Placement of cameras plays a role in the zoom
capability and angle of view a camera will require.
Typically, smaller rooms used for videoconference
applications need a wider angle of view when zoomed
out – up to 70 degrees – in order to capture all
people seated at a table. Smaller conference rooms
don’t need as much zoom magnification because of
their size, so 10x is typically adequate.
In larger venues, such as a lecture hall, a camera
with narrow angle of view – 2 degrees – may
be necessary to zoom in on a presentation area.
Larger and deeper rooms require a higher zoom
magnification to obtain close up shots that viewers
expect to see of a presenter.
By going to www.vaddio.com/tech-center
and downloading our PTZ Image Size
Calculator, you will be able to obtain the width and
height of the image that can be captured by any
of the cameras we offer, both zoomed all the way in,
as well as zoomed out.
4
Output Format
Typically, HD robotic PTZ cameras have an analog
component (YPbPr) as the standard output for the
camera. Most of the cameras also include another
type of analog or digital output or offer optional
video formats (HD-SDI, RGBHV, etc.) through the
installation of optional slot cards. Visit our website
at: www.vaddio.com for our selection of optional
slot cards.
5
CCU or PRO / SR
Does your project require multiple cameras or
the ability to adjust the camera’s color and shading
video levels? Are the auto iris and auto white balance
capabilities of the camera acceptable? Vaddio’s
camera control unit (CCU) solution allows users to
not only adjust color and iris level of each individual
camera, it also delivers power, control and video over
three Cat. 5 cables up to 500 feet away.
Our PRO systems, for the Sony BRC-series cameras and
the Panasonic HE100, allow power, video, IR and control
to be extended on three Cat. 5 cables up to 500 feet.
The PRO systems are ideal for situations where
automatic iris and white balance are acceptable,
such as videoconference applications.
Vaddio Short Range (SR) systems for our HD-20,
HD-19 and HD-18 extend power, video, control and
IR up to 100 feet over two Cat. 5 cables. The two
Short Range options include our standard SR, which
delivers component YPbPr video, or the DVI/HDMI,
which delivers DVI and component YPbPr video. In
addition, the DVI/HDMI Short Range includes daisy
chain, for connecting RS-232 to multiple cameras.
As with the PRO systems, the SR solutions are ideal
for videoconference and other applications where
auto iris and auto white balance are acceptable.
6
Camera Placement
While all of our WallVIEW camera solutions come
with a standard wall mount included, our catalog
also provides you with a variety of camera mounting
options to fit the environment where the camera
will be installed.
HD PTZ Camera System Configurations
24
Call 800-572-2011 Toll Free
vaddio.com
Vaddio HD PTZ Cameras
Vaddio ClearVIEW™ HD-20 PTZ Camera
Experience an impressive 20x Optical HiLD (High
Index Low Dispersion) lens, with imaging sensor
technology comparable to a 3-chip camera, from
Vaddio’s high definition PTZ camera, the ClearVIEW
HD-20. The multi-element motorized zoom lens and
new slip-clutch robotics system enhance performance
with smooth pan/tilt operation for accurate camera
movement and control.
technologies accumulated through the development of
CCD sensors. With a LUX rating of 1.6, the HD-20 achieves
improved picture quality in very low light environments,
resulting in a truly accurate and clean HD video image.
The new HD-20 is built around a 6.49mm diagonal
(1/3-Type) Sony Exmor sensor, which adopts the
“Column-Parallel A/D Conversion Technique” to
Vaddio ClearVIeW HD-20 PtZ Camera
create images containing more detail than ever
North america
999-6950-000
before. It combines the speed of the 3.27 megapixel
CMOS sensor with the advanced quality image sensor
International
F e at u r e s
Native HD 6.49mm diagonal (1/3-Type)
high-speed CMOS image sensor
• 20x Optical HiLD lens
• 3.27 Megapixels
• Component HD and HDMI outputs (1080p, 1080i or 720p)
• Slip-clutch Robotics System
• 1.6 LUX Rating for low-light environments
• Optional video output cards available
• Includes PowerRite power supply, IR Remote and AC cord set
WallVIEW™ HD-20
WallVIEW HD-20 DVI/HDMI
The WallVIEW HD-20 provides power to the camera and component HD video back to the
Quick-Connect SR up to 100 feet over a single Cat. 5 cable. The WallVIEW HD-20 utilizes
the EZ-Port on the back of the camera, making installation even easier.
The WallVIEW HD-20 DVI/HDMI delivers simultaneous analog component video (YPbPr) and
digital video (DVI-D or HDMI) outputs on separate connectors, ideal for multiple monitoring
and large projection systems.
• True
999-6950-001
WallVIeW HD-20
North america
999-6955-000
International
999-6955-001
F e at u r e s
• True Native HD 6.49mm diagonal (1/3-Type) high-speed
CMOS image sensor
• 20x Optical HiLD lens
• 3.27 Megapixels
• Component HD and HDMI outputs (1080p, 1080i or 720p)
• Slip-clutch Robotics System
• Quick-Connect SR up to 100 feet over a single Cat. 5 cable
• Thin Profile wall mount bracket and power supply
WallVIeW HD-20 DVI/HDMI
North america
999-6956-000
International
999-6956-001
WallVIEW CCU HD-20
WallVIEW CCU HD-20 enables the adjustment of color, gain, pedestal, gamma and iris
functions on the camera with the turn of a knob. These controls allow the camera to deliver
a more accurate representation of the image that is being captured, and color match and
shade multiple cameras. User-defined adjustments may be stored using two Scene buttons.
High speed differential signaling is used with the WallVIEW CCU HD-20 to deliver high
quality HD and SD video over standard Cat. 5 cabling. Adjustments allow the video to be
extended up to 500 feet from the Quick-Connect CCU with virtually no loss in video quality
or additional latency.
WallVIeW CCu HD-20
North america
999-6957-000
International
999-6957-001
Call 800-572-2011 Toll Free
F e at u r e s
• True Native HD 6.49mm diagonal (1/3-Type) high-speed
CMOS image sensor
• 20x Optical HiLD lens
• 3.27 Megapixels
• Component HD output on CCU (1080p, 1080i or 720p)
• Slip-clutch Robotics System
• Red and blue gain, detail, pedestal, gamma, knee, chroma
and iris controls
• Run power, video and control up to 500 feet
with Cat. 5 cable
• Thin Profile wall mount bracket and power supply
vaddio.com
F e at u r e s
Native HD 6.49mm diagonal (1/3-Type) high-speed
CMOS image sensor
• 20x Optical HiLD lens
• 3.27 Megapixels
• Component HD and DVI-D outputs (1080p, 1080i or 720p)
• Slip-clutch Robotics System
• Quick-Connect DVI/HDMI up to 100 feet over a
single Cat. 5 cable
• Thin Profile wall mount bracket and power supply
• Daisy Chain Emulation for multiple videoconferencing
codec applications
• True
For DVI to HDMI cables - Page 10
WallVIEW CCU HD-20 SDI
The WallVIEW CCU HD-20 SDI is capable of delivering HD-SDI or SD-SDI video up to 1080p
over a single coax cable.
The Quick-Connect enables adjustment of color, gain, pedestal, gamma, chroma, knee,
and iris functions on the camera with the turn of a knob.
WallVIeW CCu HD-20 sDI
North america
999-6958-000
International
999-6958-001
F e at u r e s
Native HD 6.49mm diagonal (1/3-Type) high-speed
CMOS image sensor
• 20x Optical HiLD lens
• 3.27 Megapixels - 720p (SMPTE 292M), 1080i (SMPTE
292M), 1080p (SMPTE 424M), 480i (SMPTE 259M)
and 576i (SMPTE 259M)
• HD-SDI and SD-SDI outputs
• Red and blue gain, detail, pedestal, gamma, chroma, knee
and iris controls
• Run power and control up to 500 feet over Cat. 5 cable
• Slip-clutch Robotics System
• Thin Profile wall mount bracket and power supply
• True
25
Vaddio HD PTZ Cameras
Vaddio ClearVIEW HD-19 PTZ Camera
The ClearVIEW HD-19 high definition integrated robotic PTZ camera features a 19x optical
zoom lens and is built around a 1/3-Type Exmor high-speed, low noise CMOS image
sensor with a total of 1.3 Megapixels producing precise and vibrant HD color video images.
Using an increased pixel aperture size, high frame rate, high signal to noise, and columnparallel A/D conversion method, the detail and sensitivity of the sensor are increased and
noise is diminished. Minimum illumination is rated at an astonishing 0.7 LUX.
F E At u r E S
Optical zoom lens, simultaneous component HD (480i/29.97 up to 1080/60p) and SD outputs
• 1/3-Type Exmor high-speed CMOS Image Sensor
• 19x Optical zoom lens
• 1.3 Megapixels
• Simultaneous HD (YPbPr) and SD (CVBS) outputs
• Slip Clutch Robotics
• Includes IR Remote, 12 VDC Power Supply and Power Cord
• Optional Slot Cards Available
• Available in Black or Arctic WhiteVaddio ClearVIEW HD-19 - White
• 19x
Vaddio ClearVIEW HD-19 - White
North America 999-6940-000AW
Vaddio ClearVIEW HD-19 - Black
North America 999-6940-000
International 999-6940-001AW
International 999-6940-001
WallVIEW HD-19
WallVIEW CCU HD-19
The WallVIEW HD-19 provides power to the camera and YPbPr HD video back to the QuickConnect SR up to 100 feet (30.4m) over a single Cat. 5 Cable. The WallVIEW HD-19 uses
one Cat. 5 for power and video and one Cat. 5 for RS-232 control.
The WallVIEW CCU HD-19 uses three (3) Cat. 5 cables to deliver video power and control
up to 500 feet. The CCU enables the fine tuning of the camera’s color (red and blue), AWB,
OPWB, brightness, chroma, gain, detail and iris functions.
WallVIEW HD-19 - White
North America
999-6945-000AW
International
999-6945-001AW
WallVIEW HD-19 - Black
North America
999-6945-000
International
999-6945-001
F E At u r E S
Optical zoom lens, simultaneous component HD
(480i/29.97 up to 1080/60p) and SD outputs
• 1/3-Type Exmor CMOS Image Sensor
• 1.3 Megapixels
• 19x Optical zoom lens
• Quick-Connect SR Interface - 100 feet over Cat. 5
• IR forwarding for use with VC Systems
• Thin Profile Wall Mount Included
• 19x
WallVIEW CCu HD-19 - White
North America
999-6947-000AW
International
999-6947-001AW
WallVIEW CCu HD-19 - Black
North America
999-6947-000
International
999-6947-001
F E At u r E S
Optical zoom lens, simultaneous component HD
(480i/29.97 up to 1080/60p) and SD outputs
• 1/3-Type Exmor CMOS Image Sensor
• 1.3 Megapixels
• 19x Optical zoom lens
• CCU allows for color matching cameras
• Control of red and blue gain, iris, detail, gamma, chroma
and gain functions
• Thin Profile Wall Mount Included
• 19x
WallVIEW HD-19 DVI/HDMI
WallVIEW CCU HD-19 SDI
The WallVIEW HD-19 DVI/HDMI delivers simultaneous analog YPbPr HD video and digital
video (DVI-D or HDMI) outputs on separate connectors. This system is ideal for video
conferencing, multiple monitoring and large screen projection applications.
The WallVIEW CCU HD-19 SDI outputs HD-SDI or SDI digital video and is capable of 3Gb/s
single link, single coax, HD-SDI digital video up to 1080/60. The CCU allows shading of
the camera’s color (red and blue), with brightness, AWB, OPWB, chroma, gain, detail and
iris control.
WallVIEW HD-19 DVI/HDMI White
North America
999-6946-000AW
International
999-6946-001AW
WallVIEW HD-19 DVI/HDMI Black
North America
999-6946-000
International
999-6946-001
26
F E At u r E S
Optical zoom lens, simultaneous component HD
(480i/29.97 up to 1080/60p) and SD outputs
• 1/3-Type Exmor CMOS Image Sensor
• 1.3 Megapixels
• 19x Optical zoom lens
• Simultaneous Digital (DVI-D or HDMI) and Analog (YPbPr)
and Video up to 1080/60p
• IR forwarding for use with VC Systems
• Daisy Chain Control Emulation DCCE™
• Thin Profile Wall Mount Included
• 19x
WallVIEW CCu HD-19 SDI - White
North America
999-6948-000AW
International
999-6948-001AW
WallVIEW CCu HD-19 SDI - Black
North America
999-6948-000
International
999-6948-001
F E At u r E S
Optical zoom lens, simultaneous component HD
(480i/29.97 up to 1080/60p) and SD outputs
• 1/3-Type Exmor CMOS Image Sensor
• 1.3 Megapixels
• 19x Optical zoom lens
• HD-SDI Slot Card Outputs 720p and 1080i (SMPTE 292M),
1080p (SMPTE 424M), 480i and 576i (SMPTE 259M)
• Control of red and blue gain, iris, detail, gamma, chroma
and gain functions
• Thin Profile Wall Mount Included
• 19x
Call 800-572-2011 Toll Free
vaddio.com
Vaddio HD PTZ Cameras
Vaddio ClearVIEW HD-18 PTZ Camera
The ClearVIEW HD-18 is equipped with a 1/3-inch, 1.3 megapixel CCD imaging sensor,
a glass multi-element wide dynamic zoom lens (18x optical), a tally light and a 1.8-lux
rating, providing superior images in a wide range of high-definition video applications.
High-torque, micro-stepper precision robotics enhance performance with smooth pan/tilt
operation for accurate camera movement and control.
F E AT U R E S
CCD Image Device
• 18x lens, Simultaneous Component HD
(1080p, 1080i or 720p) and SD outputs
• 1.3 Megapixels
• Includes PowerRite power supply, IR Remote
and AC cord set
• Compatible with any Polycom or TANDBERG videoconferencing codec
• Control runs via VISCA command protocol or IR remote
• 1/3-inch
Vaddio ClearVIEW HD-18 - Black
North America 999-6900-000
Vaddio ClearVIEW HD-18 - White
North America 999-6908-000AW
International 999-6900-001
International 999-6908-001AW
WallVIEW HD-18
WallVIEW CCU HD-18
The WallVIEW HD-18 provides power to the camera, and component HD video back to the
Quick-Connect SR up to 100 feet over a single Cat. 5 cable. The WallVIEW HD-18 uses the
EZ-Port on the back of the camera, making installation even easier.
WallVIEW CCU HD-18 enables the adjustment of color, gain, pedestal, gamma, chroma,
knee and iris functions on the camera with the turn of a knob.
WallVIEW HD-18 - Black
North America
999-6905-000
International
999-6905-001
WallVIEW HD-18 - White
North America
999-6905-000AW
F E AT U R E S
CCD Image Device
• 18x lens, Simultaneous Component HD
(1080p, 1080i or 720p) and SD outputs
• 1.3 Megapixels
• Quick-Connect SR up to 100 feet over a single Cat. 5 cable
• Thin Profile wall mount bracket and power supply
• 1/3-inch
WallVIEW CCU HD-18 - Black
North America
999-6907-000
International
999-6907-001
WallVIEW CCU HD-18 - White
North America
999-6907-000AW
International
999-6907-001AW
International
999-6905-001AW
F E AT U R E S
CCD Image Device
• 18x lens, Simultaneous Component HD
(1080p, 1080i or 720p) and SD outputs
• 1.3 Megapixels
• Red and blue gain, detail, pedestal, gamma,
chroma, knee and iris controls
• Thin Profile wall mount bracket and power supply
• 1/3-inch
WallVIEW HD-18 DVI/HDMI
WallVIEW CCU HD-18 SDI
The WallVIEW HD-18 DVI/HDMI delivers simultaneous analog component video (YPbPr) and
digital video (DVI-D or HDMI) outputs on separate connectors, ideal for multiple monitoring
and large projection systems.
The WallVIEW CCU HD-18 SDI is capable of HD-SDI or SDI video outputs, which transmits
3Gb/s single link HD-SDI digital video resolutions up to1080p over a single coax cable.
WallVIEW HD-18 DVI/HDMI Black
North America
999-6906-000
International
999-6906-001
WallVIEW HD-18 DVI/HDMI White
North America
999-6906-000AW
International
999-6906-001AW
Call 800-572-2011 Toll Free
F E AT U R E S
CCD Image device, 1.3 Megapixels
• 18x lens, Simultaneous Component HD and DVI-D
or HDMI outputs (up to 1080p)
• Quick-Connect DVI/HDMI up to 100 feet
over a single Cat. 5 cable
• Thin Profile wall mount bracket and power supply
• Daisy Chain Emulation for multiple videoconferencing
codec applications
• 1/3-inch
For DVI to HDMI cables - Page 10
vaddio.com
The Quick-Connect enables adjustment of color, gain, pedestal, gamma, chroma, knee and
iris functions on the camera with the turn of a knob.
WallVIEW CCU HD-18 SDI - Black
North America
999-6908-000
International
999-6908-001
WallVIEW CCU HD-18 SDI - White
North America
999-6908-000AW
International
999-6908-001AW
F E AT U R E S
CCD Image Device
• 18x lens
• 1.3 Megapixels - 720p (SMPTE 292M),
1080i (SMPTE 292M), 1080p (SMPTE 424M),
480i (SMPTE 259M) and 576i (SMPTE 259M)
HD-SDI and SD-SDI outputs
• Red and blue gain, detail, pedestal, gamma, chroma, knee
and iris controls
• Thin Profile wall mount bracket and power supply
• 1/3-inch
27
HideAway Camera Systems
IN-Ceiling™ Half-Recessed Enclosure
for HD-20, HD-19 & HD-18
CeilingVIEW™ HD HideAway
Built for the Vaddio ClearVIEW family of cameras,
the CeilingVIEW HD HideAway System provides a
quality high definition ceiling-mounted motorized lift
solution. Ideal for classrooms, training facilities and
boardrooms, the camera is quietly lowered from the
ceiling during use and completely hidden while not in
use. When retracted back into the ceiling, it fits flush
with the attractive ceiling trim ring.
For mounting the ClearVIEW HD-20, HD-19 & HD-18
cameras halfway into a ceiling tile.
F E At u r E S
back box and white metal trim ring included
• Active IR circuit in trim ring and enclosure
• Tile support brace included
• Metal
*Camera not included
SYStEM INCLuDES
HideAway Motorized Back Box assembly with
ceiling bridge mounting bracket
• CeilingVIEW HideAway power Interface for lift power and
control over Cat. 5 cable (up to 100ft.)
• Compatible with any Vaddio WallVIEW or WallVIEW DVI-HDMI
camera package. Note: The Vaddio IR remote control is
supplied with the Vaddio WallVIEW or WallVIEW DVI-HDMI
camera package and will also control the CeilingVIEW
HideAway HD System
• Includes an RJ-45/RS-232 adapter for integration with
external control systems
• CeilingVIEW
IN-Ceiling Half-recessed Enclosure
for HD-20, HD-19 and HD-18
PtZ Cameras
North America
999-2225-050
Recessed Installation Kit for IN – Ceiling Enclosure
Installation Kit used for the IN-Ceiling Half-Recessed
Enclosure.
recessed Installation Kit
for IN-Ceiling Enclosure
North America
998-2225-051
*Camera not included
F E At u r E S
for recessed drywall or hard ceilings
• Includes: mounting plates, large trim ring with active IR
receiver, and mounting hardware
• Designed
CeilingVIEW 70 PTZ
The CeilingVIEW 70 PTZ is a complete, half-recessed,
ceiling-mounted pan/tilt/zoom camera system.
The system features a Sony EVI-D70C/W camera
mounted into a recessed, metal ceiling camera
enclosure back box with ceiling tile support braces
and the Vaddio EZCamera Cabling System.
The EZCamera Cabling System allows the
installer to use Cat. 5 cabling to run power,
video and camera control.
CeilingVIEW 70 PtZ
NtSC
999-2304-000
PAL
999-2304-001
SYStEM INCLuDES
EVI-D70 Standard Definition PTZ Camera
• 1CCD Image Device
• 18x lens, NTSC/PAL
• EZCamera Cable System for video, power and control over
Cat. 5 cabling up to 157 feet
• Metal back box enclosure with tile support braces and trim ring
• Includes PowerRite power supply, IR Remote
and EZCamera Control Adapter
• Sony
CeilingVIEW HideAway
North America
999-2520-000
International
999-2520-001
28
Call 800-572-2011 Toll Free
vaddio.com
REVEAL HD PTZ Cameras
REVEAL IN-Wall Cameras are Vaddio’s first architectural integrated PTZ cameras that allow the camera to blend
into high-end videoconference and presentation rooms. The aesthetics of the camera’s design matches large flat
screen televisions and rear screen projection systems.
The camera’s back box fits into the stud cavity of a wall, allowing the
camera to blend into the wall.
There are two options for the camera – either standard glass, or with
Smart glass. The Smart glass turns opaque when the camera is powered
REVEAL™ HD-18 Frosted Glass
Camera is Live
off, or through RS-232 command. This ability to mute the camera provides
an extra level of confidence to system users who want to know that
cameras are turned off.
REVEAL HD-18 comes in two different system options, that all utilize our
Quick-Connect Cat. 5 cabling solution.
REVEAL HD-18 Clear Glass
Camera is Off/Muted
rEVEAL HD-18 (Clear Glass)
North America
999-6925-000
rEVEAL HD-18 (Frosted Glass)
North America
999-6935-000
International
999-6935-001
F E At u r E S
glass glass turns opaque and mutes video
from camera when powered down
• Transmits power and video up to 100 feet
over a single Cat. 5 cable
• 18x Optical zoom lens
• 1/3-inch CCD Image Device
• 1.3 Megapixels
• +/- 40 degrees of pan
• +25 degrees of tilt, -45 degrees of tilt
International
999-6925-001
• Smart
F E At u r E S
power and video up to 100 feet
over a single Cat. 5 cable
• 1/3-inch CCD Image Device
• 18x Optical zoom lens
• 1.3 Megapixels
• +/- 40 degrees of pan
• +25 degrees of tilt, -45 degrees of tilt
• Glass stays clear even when the camera is powered down
• Transmits
REVEAL HD-18 DVI/HDMI Clear Glass
REVEAL HD-18 DVI/HDMI Frosted Glass
rEVEAL HD-18 DVI/HDMI
(Clear Glass)
North America
999-6926-000
International
999-6926-001
Camera is Live
Camera is Off/Muted
F E At u r E S
component HD and DVI-D output
• Transmits power and video up to 100 feet over a single
Cat. 5 cable
• 18x Optical zoom lens
• 720p, 1080i or 1080p output resolution
• IR forwarding from the camera
• Daisy-chain emulation for multiple camera installations
• Glass stays clear even when the camera is powered down
• Simultaneous
REVEAL CCU Image Controller
rEVEAL HD-18 DVI/HDMI
(Frosted Glass)
North America
999-6936-000
International
999-6936-001
F E At u r E S
• Smart glass glass turns opaque and mutes video
from camera when powered down
• Simultaneous component HD and DVI-D output
• 18x Optical zoom lens
• Transmits power and video up to 100 feet over a single
Cat. 5 cable
• 720p, 1080i or 1080p output resolution
• IR forwarding from the camera
• Daisy-chain emulation for multiple camera installations
The REVEAL CCU Controller can be used with any of the REVEAL IN-Wall Camera Systems.
This CCU works in conjunction with the Control I/O of both the Quick-Connect SR and DVI/
HDMI Interfaces allowing image control and preset scenes.
Image adjustments include color, gain, pedestal, gamma, chroma, knee and iris functions
on the camera with the turn of a knob. These controls allow the camera to deliver a more
accurate representation of the image that is being captured, and color match and shade
multiple cameras.
rEVEAL CCu Image Controller
999-1105-022
Call 800-572-2011 Toll Free
vaddio.com
29
OEM PTZ Cameras
Sony BRC – H700 PTZ Camera
Sony BRC – Z700 High Definition PTZ Camera
The Sony BRC-H700 combines a high picture quality HD 3-CCD camera with pan/tilt/zoom
mechanism, wrapped in a sleek, compact body. The BRC-H700 supports analog RGB,
YPbPr output as standard and is also equipped with a slot for optional cards.
The BRC-Z700 combines a high picture quality HD 3-CMOS camera with pan/tilt/zoom
mechanism, wrapped in a sleek, compact body. Like its other family members, the BRC300 and the BRC-H700, the BRC-Z700 can also be ceiling mounted. The BRC-Z700
supports simultaneous outputs of analog HD YPbPr output as well as Y/C and composite in
Standard Definition (SD).
sony BrC‑H700
North america
999‑6700‑000
International
999‑6700‑001
F e at u r e s
Image Device
• 12x lens, 1080i/59.94i, 1080/50i (switchable)
• 1.07 Megapixels
• Includes PowerRite power supply, IR remote
and AC cord set
• 3-CCD
F e at u r e s
Image Device
• 20x lens, 1080i/59.94i, 1080/50i (switchable)
with simultaneous SD output
• 1.12 Megapixels
• Includes PowerRite power supply, IR Remote
and AC cord set
• 3-CMOS
sony BrC‑Z700
North america
999‑6800‑000
International
999‑6800‑001
WallVIEW CCU H700
WallVIEW CCU Z700
The WallVIEW CCU H700 is built around the Sony BRC-H700 high definition pan/tilt/zoom
camera, with 3-CCDs and a 12x optical zoom lens. WallVIEW CCU H700 enables the
adjustment of color, gain and iris functions on the camera with the turn of a knob.
The WallVIEW CCU Z700 is built around the Sony BRC-Z700 high definition pan/tilt/zoom
camera, with 3-CMOS megapixel sensors and a 20x optical zoom lens. WallVIEW CCU Z700
enables the adjustment of color, gain and iris functions on the camera.
WallVIeW CCu H700
North america
999‑6707‑000
International
999‑6707‑001
F e at u r e s
• Sony BRC-H700 High Definition PTZ Camera
• 3-CCD Image Device
• 12x lens, 1080i/59.94i, 1080/50i (switchable)
• Red and blue gain, detail, color and hue gain, WB shift,
iris and gain controls
• Video, power and control run over Cat. 5 cabling
up to 500 feet
• Heavy-duty wall mount bracket and power supply
WallVIeW CCu Z700
North america
999‑6807‑000
International
999‑6807‑001
F e at u r e s
BRC-Z700 High definition PTZ Camera
• 3-CMOS Image Device
• 20x lens, 1080i/59.94i, 1080/50i (switchable)
with simultaneous SD output
• Red and blue gain, detail, red, green and blue enhance,
iris and gain controls
• Video, power and control run over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and power supply
• Sony
WallVIEW PRO Z700
WallVIEW PRO H700
The WallVIEW PRO H700 is built around the Sony BRC-H700 high definition pan/tilt/zoom
camera, with 3-CCDs and a 12x optical zoom lens.
The WallVIEW PRO Z700 is built around the Sony BRC-Z700 high definition pan/tilt/zoom
camera, with 3-CMOS megapixel sensors and a 20x optical zoom lens.
HSDS is used with the WallVIEW PRO Z700 to deliver high quality HD video over standard
Cat. 5 cabling. Adjustments allow the video to be extended up to 500 feet from the QuickConnect PRO with virtually no loss in video quality or additional latency.
HSDS is used with the WallVIEW PRO H700 to deliver high quality HD video over standard
Cat. 5 cabling. Adjustments allow the video to be extended up to 500 feet from the QuickConnect PRO with virtually no loss in video quality or additional latency.
WallVIeW PrO Z700
North america
999‑6805‑000
WallVIeW PrO H700
North america
999‑6704‑000
International
999‑6704‑001
F e at u r e s
Image Device
• 12x lens, 1080i/59.94, 1080/50 (switchable)
• PRO series EZCamera Cabling System for running video,
power, IR and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and PowerRite power supply
• 3-CCD
International
999‑6805‑001
F e at u r e s
BRC-Z700 High definition PTZ Camera
• 3-CMOS Image Device
• 20x lens, 1080i/59.94i, 1080/50i
(switchable) with simultaneous SD output
• PRO series EZCamera Cabling System for running video,
power, IR and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and PowerRite power supply
• Sony
Wide Angle Conversion Lens for Sony BRC – Z700
High Definition 0.8x wide conversion lens with a focal length of 29.9mm (35mm equivalent).
Wide angle Conversion Lens for sony BrC‑Z700
998‑6522‑007
30
Call 800-572-2011 Toll Free
vaddio.com
OEM PTZ Cameras
Sony EVI – HD1 PTZ Camera
Sony BRC – Z330
The EVI-HD1 camera combines a high-quality HD color video camera with the flexibility
of remote pan/tilt/zoom operation. With 14 formats to choose from (including eight HD
types and six SD video formats), smooth, high-speed pan/tilt operation, 16 x 9 aspect ratio
images and a built-in 10x optical zoom/wide angle lens, the EVI-HD1 is ideal for small to
medium size conference rooms.
The BRC-Z330 employs a 1/3-type ClearVid CMOS image sensor, an 18x optical zoom lens
and is both HD and SD capable. The BRC-Z330 simultaneously delivers HD images (1080i
or 720p) and SD images.
F E At u r E S
BRC-Z330 High definition PTZ Camera
• 1/3-inch CMOS Image Device
• 18x lens, 1080i or 720p (switchable)
with simultaneous SD output
• Includes PowerRite power supply, IR Remote
and AC cord set
• Sony
F E At u r E S
• 1/3-type, 2-Megapixel
CMOS Image Sensor
10x Optical zoom lens
(4x Digital - 40x Total Zoom)
• 1080i and 720p HD Resolutions,
480i and 576i SD Resolutions
• Includes IR Remote Control, Power Supply and AC Cord Set
• Wide Angle
Sony EVI-HD1
North America
999-6300-000
Sony BrC-Z330
North America
999-6850-000
International
999-6300-001
International
999-6850-001
WallVIEW CCU HD1
WallVIEW CCU Z330
The WallVIEW CCU HD1 is built around the Sony EVI-HD1 high definition pan/tilt/zoom camera,
with a 2 megapixel CMOS sensor and a 10x optical zoom lens. WallVIEW CCU HD1 enables the
adjustment of color, gain and iris functions on the camera with the turn of a knob.
The WallVIEW CCU Z330 is built around the Sony BRC-Z330 high definition pan/tilt/
zoom camera, with a 1/3-inch CMOS megapixel sensor and an 18x optical zoom lens.
Adjustments allow the video to be extended up to 500 feet from the Quick-Connect CCU
with virtually no loss in video quality or additional latency.
WallVIEW CCu HD1
North America
999-6307-000
International
999-6307-001
F E At u r E S
EVI-HD1 High Definition PTZ Camera
• CMOS Image Device
• 10x lens, 1080i/720p/480i (switchable)
• Red and blue gain, aperture, iris and gain controls
• Video, power and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and power supply
• Sony
WallVIEW CCu Z330
North America
999-6857-000
International
999-6857-001
F E At u r E S
BRC-Z330 High definition PTZ Camera
• 1/3-inch CMOS Image Device
• 18x lens, 1080i or 720p (switchable) with simultaneous SD
output
• Red and blue gain, detail, red, green and blue enhance, iris
and gain controls
• Video, power and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and power supply
• Sony
WallVIEW PRO HD1
WallVIEW PRO Z330
The WallVIEW PRO HD1 is built around the Sony EVI-HD1 high definition pan/tilt/zoom
camera, with a 2 megpixel CMOS sensor and a 10x optical zoom lens.
The WallVIEW PRO Z330 is built around the Sony BRC-Z330 high definition pan/tilt/zoom
camera, with a 1/3-inch CMOS megapixel sensor and an 18x optical zoom lens.
HSDS is used with the WallVIEW PRO HD1 to deliver high quality HD video over standard
Cat. 5 cabling. Adjustments allow the video to be extended up to 500 feet from the QuickConnect PRO with virtually no loss in video quality or additional latency.
HSDS is used with the WallVIEW PRO Z330 to deliver high quality HD video over standard
Cat. 5 cabling. Adjustments allow the video to be extended up to 500 feet from the QuickConnect PRO with virtually no loss in video quality or additional latency.
WallVIEW PrO HD1
North America
999-6305-000
WallVIEW PrO Z330
North America
999-6855-000
International
999-6305-001
Call 800-572-2011 Toll Free
F E At u r E S
EVI-HD1 High Definition PTZ Camera
• CMOS Image Device
• 10x lens, 1080i/720p/480i (switchable)
• PRO series EZCamera Cabling System for running video,
power, IR and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and PowerRite power supply
• Sony
vaddio.com
International
999-6855-001
F E At u r E S
BRC-Z330 High definition PTZ Camera
• 1/3-inch CMOS Image Device
• 18x lens, 1080i or 720p (switchable)
with simultaneous SD output
• PRO series EZCamera Cabling System for running video,
power, IR and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and power supply
• Sony
31
OEM PTZ Cameras
Panasonic AW – HE100 PTZ Camera
WallVIEW PRO HE100
The Panasonic AW-HE100 integrated HD/SD camera offers broadcast-quality video with
smooth pan/tilt/zoom operation and easy system configuration. With three 1/3-inch CCDs,
a fast f1.6 zoom lens, 19-bit video processing DSP (digital signal processor) and 14-bit A/D
converter, the camera produces exceptional high definition images in a variety of lighting
conditions and environments.
The WallVIEW PRO HE100 is built around the Panasonic AW-HE100 high definition pan/
tilt/zoom camera, with 3-CCDs and a 13x optical zoom lens. Because the WallVIEW PRO
HE100 operates on 12 Volt DC, it easily integrates into projects where no AC outlet is
required at the camera location.
Panasonic AW-HE100
North America
999-6110-000
F E At u r E S
• 12 Volt DC
• 3-CCD Image Device
• 13x lens, 720p/1080i (switchable)
with simultaneous SD output
• A switchable Smart Flip feature automatically flips
the picture (with no glitches) when camera tilts
beyond a selected point
• Includes PowerRite power supply, IR Remote
and AC cord set
International
999-6110-001
HSDS is used with the WallVIEW PRO HE100 to deliver high quality HD video over standard
Cat. 5 cabling. Adjustments allow the video to be extended up to 500 feet from the QuickConnect PRO with virtually no loss in video quality or additional latency.
WallVIEW PrO HE100
North America
999-6115-000
WallVIEW CCU HE100
International
999-6115-001
The WallVIEW CCU HE100 is built around the Panasonic AW-HE100 high definition pan/
tilt/zoom camera, with 3-CCDs and a 13x optical zoom lens. Because the WallVIEW CCU
HE100 operates on 12 Volt DC, it easily integrates into projects where no AC outlet is
required at the camera location.
F E At u r E S
DC Panasonic AW-HE100 High Definition
PTZ camera and remote
• 3-CCD Image Device
• 13x lens, 720p/1080i (switchable)
with simultaneous SD output
• PRO series EZCamera Cabling System for running video,
power, IR and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and PowerRite power supply
• 12 Volt
WallVIEW CCU HE100 enables the adjustment of color, gain, pedestal, gamma and iris
functions on the camera with the turn of a knob.
Sony EVI – HD7V PTZ Camera
The EVI-HD7V, a 1080i High Definition pan/tilt/zoom camera is equipped with a DVI-I
Interface designed to maximize high video quality displays and is capable of displaying
both digital and analog signals (output is selectable from YPbPr and RGB).
F E At u r E S
CMOS
• 10x Optical, 40x with digital zoom
• 2 Megapixels
• Includes PowerRite power supply, IR Remote
and AC cord set
• 1/3-type
WallVIEW CCu HE100
North America
999-6117-000
International
999-6117-001
F E At u r E S
DC Panasonic AW-HE100 High Definition PTZ
camera and remote
• 3-CCD Image Device
• 13x lens, 720p/1080i (switchable) with simultaneous SD output
• Red and blue gain, detail, chroma, gamma, pedestal,
iris and gain controls
• Video, power and control run over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and power supply
• 12 Volt
Sony EVI-HD7V
North America
999-6370-000
International
999-6370-001
Sony EVI – HD3V PTZ Camera
The EVI-HD3V, a 720p HD pan/tilt/zoom camera is equipped with a DVI-I Interface designed
to maximize high video quality displays and is capable of displaying both digital and analog
signals (output is selectable from Y/Pb/Pr and RGB).
F E At u r E S
type CMOS
• 10x Optical, 40x with digital zoom
• 2 Megapixels
• Includes PowerRite power supply, IR Remote
and AC cord set
• 1/3
Sony EVI-HD3V
North America
999-6330-000
International
999-6330-001
32
Call 800-572-2011 Toll Free
vaddio.com
OEM PTZ Cameras
Canon BU – 46H®
Canon BU – Series CCU Image Controller
The Canon BU-46H weatherproof remote control robotic pan-tilt HD 16:9 camera features
a Canon HD camera equipped with three 1/3-inch (1.67 million-pixel) CCDs, a Genuine
Canon HD zoom lens with 20x optical zoom ratio (4.5 - 90mm), and a remote-control ND
(neutral density) filter.
The CCU Image Controller for the Canon BU-Series of PTZ cameras allows you to control
the color and shading of the BU-Series camera’s video output. Equipped with Control IN
and OUT, the CCU Image Controller can be run in-line with Vaddio’s ProductionVIEW HD-SDI
or the Precision Camera Controller.
Outputs include HD-SDI or SD-SDI with embedded audio (using a third-party microphone)
and standard-definition composite NTSC. The BU-46H remote-control robotic pan-tilt
HD camera can output HD-SDI and composite video simultaneously for high-definition
recording and standard-definition monitoring at the same time.
The CCU Image Controller enables the adjustment of color, gain, pedestal, gamma, chroma,
knee and iris functions on the camera with the turn of a knob. These controls allow the
camera to deliver a more accurate representation of the image that is being captured and
color match and shade multiple cameras.
The Canon BU-46H can be controlled by Vaddio’s Precision Camera Controller and
ProductionVIEW HD-SDI with the included adapters.
F E At u r E S
HD 3-CCD Image Device
• Canon HD lens with 20x optical zoom ratio (4.5 - 90mm)
• Outputs include HD-SDI or SD-SDI with embedded audio or
standard-definition composite video (simultaneous HD-SDI
and SD composite video)
• Powered by 12V DC and provides Genlock input
• Capable of panning 340 degrees and tilting 80 degrees (30
degrees up, 50 down)
• The outdoor pan-tilt head and weatherproof housing is
designed for operation from -15 to +40 degrees Celsius (+5
to +104 degrees Fahrenheit)
• Auto Focus function and Canon’s Image Stabilizer
technology
• Can be controlled by Vaddio Precision Camera Controller
and ProductionVIEW HD-SDI, adapters included
• 1/3-inch
Canon Bu-46H
North America
999-4146-000
International
999-4146-001
Canon Bu-Series
CCu Image Controller
North America
999-4190-000
International
999-4190-001
F E At u r E S
• Color, gain, pedestal, gamma, chroma, knee
and iris
functions
• Control over Cat. 5 up to 500 feet
Canon Bu Series of PtZ cameras with ProductionVIEW HD-SDI
Canon BU – 51H®
The BU-51H remote-control robotic indoor pan-tilt HD camera system incorporates a
Canon HD camera equipped with three 1/3-inch (1.67 million-pixel) CCD sensors (1440 H
x 1080 V), a Canon HD zoom lens with 20x optical zoom ratio (4.5 - 90mm), an advanced
Canon Auto Focus function, and Canon’s Image Stabilizer technology.
Outputs include uncompressed HD-SDI or SD-SDI and standard-definition (SD) composite
NTSC video. The HD-SDI can be used for HD recording and the composite video will
support simultaneous SD monitoring. The BU-51H pan-tilt HD camera is capable of
extremely smooth 300 degrees of panning and 80 degrees of tilt. The Canon BU-51H can
be controlled by Vaddio’s Precision Camera Controller and ProductionVIEW HD-SDI with
the included adapters.
F E At u r E S
HD 3CCD
• Canon HD lens with 20x optical zoom ratio (4.5 - 90mm)
• Outputs include HD-SDI or SD-SDI and standard-definition
composite NTSC (simultaneous HD-SDI and SD composite
video)
• Powered by 100-240V AC
• Genlock input
• Capable of panning 300 degrees and tilting 80 degrees (40
degrees up, 40 down)
• Auto Focus function and Canon’s Image Stabilizer
technology
• Can be controlled by Vaddio Precision Camera Controller
and ProductionVIEW HD-SDI, adapters included
• 3-1/3-inch
Canon Bu-51H
North America
999-4151-000
International
999-4151-001
Call 800-572-2011 Toll Free
vaddio.com
Canon Bu Series of PtZ cameras
with Precision Camera Controller and HD-SDI Switcher
33
OEM PTZ Cameras
Sony BRC – 300 PTZ Camera
Sony EVI – D70 PTZ Camera
The BRC-300 incorporates three 1/4.7-type
Advanced HAD™ CCDs to provide high-quality,
high-resolution images in both 4:3 and 16:9 modes.
With its E: Flip function for desktop or ceiling mount
flexibility, the BRC-300 is ideal for use in a wide
range of remote video shooting applications such
as houses of worship, distance learning, corporate
training, and cable TV broadcasting.
F E AT U R E S
• 3-CCD Image Device
• 12x lens, NTSC/PAL with simultaneous Y/C (S-Video)
and composite outputs
• 600 TVL
• 1.07 Megapixels
• Includes PowerRite power supply, IR Remote
and AC cord set
Sony BRC-300 PTZ Camera
NTSC
999-6000-000
PAL
999-6000-001
The ceiling-mountable EVI-D70 combines a high
quality 1/4 type EXview HAD™ CCD color camera with
the flexibility of a remote pan/tilt/zoom operation,
all in a compact easy-to-use package. Compared to
its predecessor, the EVI-D70 camera incorporates a
wider pan/tilt range with an 18x optical zoom lens
and a faster pan/tilt mechanism.
F E AT U R E S
Image Device
• 18x lens, NTSC/PAL
• 470 TVL
• Includes power supply, IR Remote and AC cord set
• 1CCD
Sony EVI-D70 PTZ Camera
NTSC
999-2000-070
PAL
999-2000-071
Model 70 PTZ Camera Kit
The Model 70 PTZ Camera Kit is built around
the Sony EVI-D70 PTZ camera and includes the
EZCamera Cable Shoe and IR Remote Commander.
The EZCamera Cabling System allows the installer
to use Cat. 5 cabling to run power, video and camera
control.
WallVIEW CCU 300
The WallVIEW CCU 300 is built around the Sony BRC-300 standard definition pan/tilt/
zoom camera, with 3-CCDs and a 12x optical zoom lens. WallVIEW CCU 300 enables the
adjustment of color, gain and iris functions on the camera with the turn of a knob.
SySTEm INCLUDES
EVI-D70 Standard Definition PTZ Camera
• 1CCD Image Device
• 18x lens, NTSC/PAL
• EZCamera Cable System for video, power and control
over Cat. 5 cabling up to 200 feet
• Vaddio’s IR Remote Commander
• Sony
model 70 PTZ Camera Kit
NTSC
999-2001-070
WallVIEW CCU 300
NTSC
999-6207-000
PAL
999-6207-001
F E AT U R E S
BRC-300 Standard Definition PTZ Camera
• 3-CCD Image Device
• 12x lens, NTSC/PAL with simultaneous Y/C (S-Video) and
composite outputs
• 600 TVL
• Red and blue gain, aperture, iris and gain controls
• Video, power and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and power supply
• Sony
WallVIEW PRO 300
The WallVIEW PRO 300 is built around the Sony BRC-300 standard definition pan/tilt/zoom
camera, with 3-CCDs and a 12x optical zoom lens.
PAL
999-2001-071
WallVIEW 70 PTZ
The WallVIEW 70 PTZ is a complete wall mounted
pan/tilt/zoom camera system. The system includes a
Sony EVI-D70 PTZ camera, a thin profile wall mount
bracket for the camera and the Vaddio EZCamera
Cabling System. The EZCamera Cabling System
allows the installer to use Cat. 5 cabling to run
power, video and camera control. Also included is
Vaddio’s PowerRite Power Supply. The PowerRite
system regulates the right amount of power needed
for the camera over Cat. 5 cabling.
WallVIEW 70 PTZ
NTSC
999-2704-000
PAL
999-2704-001
WallVIEW 70 PTZ Black Camera
Version
NTSC
999-2704-000B
PAL
999-2704-001B
WallVIEW PRO 300
NTSC
999-6205-000
PAL
999-6205-001
34
F E AT U R E S
BRC-300 Standard Definition PTZ Camera
• 3-CCD Image Device
• 12x lens, NTSC/PAL with simultaneous Y/C (S-Video)
and composite outputs
• 600 TVL
• PRO series EZCamera Cabling System for running video,
power, IR and control over Cat. 5 cabling up to 500 feet
• Sony
SySTEm INCLUDES
EVI-D70 Standard Definition PTZ Camera
• 1CCD Image Device
• 18x lens, NTSC/PAL
• EZCamera Cable System for video, power and control
over Cat. 5 cabling up to 200 feet
• Thin profile wall mount bracket and power supply
• Sony
Black Camera Version Available
Black Camera, EZCamera cable shoe
and thin profile wall mount
• Includes
Wide Angle Camera Lens Option for Sony EVI – D70
Wide angle lens for Sony EVI-D70 with 37mm
threads and .5x magnification.
F E AT U R E S
threads
• .5x magnification
• 100 percent wider image
• 37mm
Kenko EVI-D70 Lens
534-0000-001
Call 800-572-2011 Toll Free
vaddio.com
OEM PTZ Cameras
Sony EVI – D100 PTZ Camera
The EVI-D100 is a high quality CCD camera that
combines a high-speed, quiet pan/tilt with a wideangle view and 40x zoom (10x optical + 4x digital),
all in a compact, easy-to-use package. The EVI-D100
camera features auto focus, auto white balance
and automatic exposure control that provide fast
and stable hands free operation when the camera
changes pan/tilt positions.
Sony EVI-D100 PTZ Camera
NTSC
999-2000-100
PAL
999-2000-101
CoverVIEW™ for Sony EVI – D100 – Black / White
The CoverVIEW is a simple and attractive way to install the Sony EVI-D100 and WallVIEW
100 PTZ cameras into a wall cavity.
The system is comprised of a metal back box and a curved, acrylic cover. An adjustable
tripod screw slot on the bottom of the box allows for fastening the PTZ camera to the box.
The cover is made of ABS plastic and has a clear acrylic, non-reflective lens mounted across
the opening.
F E AT U R E S
Image Device
• 10x lens, NTSC/PAL
• 470 TVL
• Includes power supply, IR Remote and AC cord set
• 1CCD
Model 100 PTZ Camera Kit
The Model 100 PTZ Camera Kit is built around the Sony EVI-D100 PTZ camera and includes
the EZCamera Cable Shoe and IR Remote Commander. The EZCamera Cabling System
allows the installer to use Cat. 5 cabling to run power, video and camera control.
model 100 PTZ Camera Kit
NTSC
999-2001-100
PAL
999-2001-101
SySTEm INCLUDES
EVI-D100 Standard Definition PTZ Camera
• 1CCD Image Device
• 10x lens, NTSC/PAL
• EZCamera Cable System for video, power and control
over Cat. 5 cabling up to 115 feet
• Vaddio’s IR Remote Commander
• Sony
CoverVIEW for Sony
EVI-D100 - Black
999-2221-000
CoverVIEW for Sony
EVI-D100 - White
999-2221-001
F E AT U R E S
camera enclosure cover
• Plenum-rated metal back box with conduit knockouts
• Clear acrylic non-reflective camera lens
• Two extruded trim clips
• Mounting hardware
• Attractive
WallVIEW 100 PTZ
WallVIEW 100 PTZ
NTSC
999-2204-000
PAL
999-2204-001
WallVIEW 100 PTZ
Black Camera Version
NTSC
999-2204-000B
PAL
999-2204-001B
Call 800-572-2011 Toll Free
The WallVIEW 100 PTZ is a complete wall mounted
pan/tilt/zoom camera system. The system includes a
Sony EVI-D100 PTZ camera, a thin profile wall mount
bracket for the camera and the Vaddio EZCamera
Cabling System. The EZCamera Cabling System
allows the installer to use Cat. 5 cabling to run power,
video and camera control. Also included is Vaddio’s
PowerRite Power Supply. The PowerRite system
regulates the right amount of power needed for the
camera over Cat. 5 cabling.
SySTEm INCLUDES
EVI-D100 Standard Definition PTZ Camera
• 1CCD Image Device
• 10x lens, NTSC/PAL
• EZCamera Cable System for video, power and control
over Cat. 5 cabling up to 115 feet
• Thin profile wall mount bracket and power supply
• Sony
Black Camera Version Available
black camera,
EZCamera cable shoe and thin profile wall mount
• Includes
vaddio.com
35
OEM PTZ Cameras
Canon VC–C50i PTZ Camera
WallVIEW 50i PTZ
The Canon VC-C50i PTZ camera combines a 1/4-inch CCD
image sensor with 340,000 effective pixels and offers a 26x
optical and 12x digital zoom lens. The VC-C50i delivers high
quality video from far distances, even in no-light conditions up
to ten feet away.
F e At u R e S
Image Device
• 26x lens, NTSC/PAL
• 460 TVL
• Includes power supply, IR Remote and AC cord set
• 1-CCD
canon Vc‑c50i
PtZ camera
ntSc
999‑4000‑000
WallVieW 50i PtZ
ntSc
999‑4204‑000
PAl
999‑4204‑001
PAl
999‑4000‑001
Canon VC–C50iR PTZ Camera
F e At u R e S
Image Device
• 26x lens, NTSC/PAL
• 460 TVL
• Includes power supply, IR Remote and AC cord set
canon Vc‑c50iR
PtZ camera
ntSc
999‑4001‑000
PAl
999‑4001‑001
Model 50i PTZ Camera Kit
The Model 50i PTZ Camera Kit is built around the Canon VCC50i PTZ camera and includes the EZCamera Cable Shoe and
IR Remote Commander. The EZCamera Cabling System allows
the installer to use Cat. 5 cabling to run power, video and
camera control.
model 50i
PtZ camera Kit
ntSc
999‑2001‑050
PAl
999‑2001‑051
SyStem includeS
Standard Definition PTZ Camera
• 1-CCD Image Device
• 26x lens, NTSC/PAL
• EZCamera Cable System for video, power and control over Cat. 5
cabling up to 185 feet
• Vaddio’s IR Remote Commander
The Model 50iR PTZ Camera Kit is built around the Canon
VC-C50iR inverted PTZ camera and includes the EZCamera
Cable Shoe and IR Remote Commander. The EZCamera Cabling
System allows the installer to use Cat. 5 cabling to run power,
video and camera control.
model 50iR
PtZ camera Kit
ntSc
999‑2001‑060
PAl
999‑2001‑061
36
The CeilingVIEW 50iR PTZ Camera System is built around the
Canon® VC-C50iR Inverted PTZ Camera equipped with Vaddio’s
suspended ceiling PTZ camera mount and Vaddio’s EZCamera
Cabling system. The EZCamera Cabling System allows the
installer to use Cat. 5 cabling to run power, video and camera
control. Also included is Vaddio’s PowerRite Power Supply.
ceilingVieW 50iR PtZ
ntSc
999‑4304‑000
PAl
999‑4304‑001
SyStem includeS
• Inverted Canon VC-C50iR Standard Definition PTZ Camera
• 1-CCD Image Device
• 26x lens, NTSC/PAL
• EZCamera Cable System for video, power and control over Cat. 5
cabling up to 185 feet
• Vaddio’s IR Remote Commander
SyStem includeS
Canon VC-C50iR Standard Definition PTZ Camera
• 1-CCD Image Device
• 26x lens, NTSC/PAL
• EZCamera Cable System for video, power and control over Cat. 5
cabling up to 185 feet
• Suspended ceiling camera mount including mounting rail,
escutcheon ring and mounting hardware
• Includes PowerRite power supply, IR Remote and
EZCamera Control Adapter
• Inverted
CoverVIEW for Canon VC–C50i – Black
The CoverVIEW is a simple and attractive way to install the Canon VC-C50i and WallVIEW
50i PTZ cameras into a wall cavity.
The system is comprised of a metal back box and a curved, acrylic cover. An adjustable
tripod screw slot on the bottom of the box allows for fastening the PTZ camera to the box.
The cover is made of ABS plastic and has a clear acrylic, non-reflective lens mounted across
the opening.
• Canon VC-C50i
Model 50iR PTZ Camera Kit
SyStem includeS
Standard Definition PTZ Camera
• 1-CCD Image Device
• 26x lens, NTSC/PAL
• EZCamera Cable System for video, power and control
over Cat. 5 cabling up to 185 feet
• Thin profile wall mount bracket and power supply
• Canon VC-C50i
CeilingVIEW 50iR PTZ
The inverted Canon VC-C50iR PTZ camera combines a 1/4inch CCD image sensor with 340,000 effective pixels and
offers a 26x optical and 12x digital zoom lens. The VC-C50iR
delivers high quality video from far distances, even in no-light
conditions up to ten feet away.
• 1-CCD
The WallVIEW 50i PTZ is a complete wall mounted pan/tilt/
zoom camera system. The system includes a Canon VC-C50i
PTZ camera, a thin profile wall mount bracket for the camera
and the Vaddio EZCamera Cabling System. The EZCamera
Cabling System allows the installer to use Cat. 5 cabling to
run power, video and camera control. Also included is Vaddio’s
PowerRite Power Supply.
F e At u R e S
camera enclosure cover
• Plenum-rated metal back box
with conduit knockouts
• Clear acrylic non-reflective
camera lens
• Two extruded trim clips
• Mounting hardware
• Available only in black
• Attractive
coverVieW for
canon Vc‑c50i ‑ Black
999‑2224‑000
Wide Angle Camera Lens Option for Canon VC–C50i
Wide angle lens for Canon VC-C50i and VC-C50iR
with 37mm threads and .75x magnification.
F e At u R e S
threads
• .75x magnification
• 33 percent wider image
• 37mm
canon Vc‑c50i lens
534‑0000‑002
Call 800-572-2011 Toll Free
vaddio.com
EZ Camera Systems & Accessories
EZCamera Cable Components are products integrators use with EZCamera PTZ cameras to design their packages
based on customer application. Power supplies, Quick-Connect 4 wiring center, rack panels, thin profile wall
mounts, control adapters and accessories are the component options available.
Quick–Connect™ Box
EZCamera™ Control Adapter
The Quick-Connect Box converts Cat. 5 connection from the EZCamera Shoe back to the
native power, S-video and composite video in a matchbox-sized box that sits back in the
rack with the head-end equipment.
The RJ-45 to DB9F adapter converts standard Cat. 5
cable with an RJ-45 connecter to DB9 connecter.
For use with control systems and codecs with
RS-232 ports.
eZCamera Control adapter
998‑1001‑232
Quick‑Connect Box
998‑1105‑001
EZCamera Control Adapter for TANDBERG Codecs
The RJ-45 to DB9M adapter for TANDBERG codecs
eliminates the need for a null-modem adapter and
gender changer when converting Cat. 5 control
cabling to the Vaddio EZCamera control standard.
Quick–Connect Box Rack Panel
The Quick-Connect Box Rack Panel mounts up to three Quick-Connect boxes on a tray
attached to the back of the rack panel (Quick-Connect boxes are not included).
eZCamera Control adapter
for taNDBeRG Codecs
998‑1002‑232
EZCamera Control Adapter
for Polycom HDX Series Codecs
Quick‑Connect Box Rack Panel
998‑1105‑002
The RJ-45 to DB9M adapter, for Polycom HDX
Series codecs to WallVIEW Kits, eliminates the need
for a null-modem adapter and gender changer
when converting Cat. 5 control cabling to the
Vaddio EZCamera control standard.
Quick–Connect 4
eZCamera Control adapter
for Polycom HDX series Codecs
998‑1006‑232
The Vaddio Quick-Connect 4 video, power and control wiring center can accommodate up
to four single chip EZCamera PTZ Series cameras. The Quick-Connect 4 combines four of
the Quick-Connect boxes, four EZCamera Control Adapters and four power supplies. Used
in conjunction with the EZCamera Cabling System, the Quick-Connect 4 centralizes control
system wiring and supplies power distribution from a single master power supply.
Vaddio IR Remote Commander
Controls the following Vaddio/Sony-based camera
packages:
• Vaddio
Vaddio iR
Remote
Commander
998‑2100‑000
HD-20, HD-19 and HD-18 Camera Systems
WallVIEW PRO 70, 100, 300, HD1, Z700 and H700
• WallVIEW CCU 300, HD1, Z700 and H700
• CeilingVIEW 70 PTZ and CeilingVIEW 70 PTZ HideAway
• Models 100 PTZ and Model 70 PTZ
• PTZCAM 100 and PTZCAM 70
• EVI-D70, EVI-D100, BRC-300, BRC-Z700 and BRC-H700
24 Volt Power Supply
Quick‑Connect 4
North america
999‑5100‑000
international
999‑5100‑001
F e at u R e s
Rack enclosure with centralized power supply
and control ports
• S-Video and composite outputs (NTSC/PAL)
• Supports four EZCamera Cable Systems for video,
power and control over Cat. 5 cabling
C o m Pat i B l e Ca m e R a s
• WallVIEW 100 PTZ, WallVIEW 70 PTZ, WallVIEW 50i
PTZ, CeilingVIEW 70, CeilingVIEW 50iR, CeilingVIEW SD,
CeilingVIEW HD, WallVIEW 50i PTZ Hideaway, Model 100
PTZ, Model 70 PTZ, Model 50i PTZ, Model 50iR PTZ
Call 800-572-2011 Toll Free
F e at u R e s
• Extends WallVIEW
• 2-RU
vaddio.com
24 Volt Power supply
451‑2000‑024
and Model 100 PTZ Cameras
115 feet to 250 feet
• Extends WallVIEW and Model 70 PTZ Cameras
200 feet to 300 feet
• Extends WallVIEW and Model cameras 50i PTZ Cameras
185 feet to 275 feet
• Extends WallVIEW and Model cameras 50iR PTZ Cameras
185 feet to 275 feet
37
Videoconferencing Peripherals
From mounting hardware and cabling systems to PTZ cameras, Vaddio provides everything you need to transform
a videoconferencing system into a complete solution. Vaddio’s videoconferencing peripherals are designed to
provide an easy way to install Polycom and TANDBERG videoconferencing systems with standard Cat. 5 cables.
WallVIEW PRO EagleEye®/EagleEye II
TANDBERG Cameras with OneLINK™ Technology
The WallVIEW PRO EagleEye /EagleEye II is designed for use with the Polycom© EagleEye
high definition pan/tilt/zoom camera. The WallVIEW PRO’s active electronics deliver high
definition video up to 500 feet (152.4m) over standard Cat. 5 cabling from the EagleEye /
EagleEye II PTZ camera (not included).
Vaddio’s OneLINK technology is designed to work with both the TANDBERG® Precision
HD 720p and Precision HD 1080p cameras. For the C20, C40, C60 and C90 codecs only.
The Quick-Connect OneLINK utilizes a single Cat. 5 cable to transmit video, power and
control to the camera up to 125 feet.
WallVIEW PrO EagleEye/EagleEye II
North America
999-9500-000
International
999-9500-001
F E At u r E S
series EZCamera Cabling System for running video,
power, IR and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and power supply
• Polycom IR pass-through
**Camera not included
• PRO
tANDBErG Cameras
with OneLINK technology
North America
999-9550-000
International
999-9550-001
F E At u r E S
Cat. 5 cable for video, power and control
up to 125 feet
• Compatible with both TANDBERG Precision HD 720p
and Precision HD 1080p
• For use with the C20, C40, C60 and C90 codecs only
• Heavy-duty wall mount bracket
• IR pass-through from Precision HD camera
to TANDBERG codec
• Single
**camera not included
WallVIEW PRO EagleEye 1080 HD®
OneLINK System Configuration
The WallVIEW PRO EagleEye 1080 HD is designed for use with the Polycom EagleEye
high definition pan/tilt/zoom camera. The WallVIEW PRO’s active electronics deliver high
definition video up to 500 feet (152.4m) over standard Cat. 5 cable from the EagleEye PTZ
camera (not included).
WallVIEW PrO EagleEye 1080 HD
North America
999-9510-000
International
999-9510-001
F E At u r E S
series EZCamera Cabling System for running video,
power, IR and control over Cat. 5 cabling up to 500 feet
• Heavy-duty wall mount bracket and power supply
• Polycom IR pass-through
• PRO
**camera not included
38
Call 800-572-2011 Toll Free
vaddio.com
Videoconferencing Mounts
Thin Profile Wall Mount Bracket for TANDBERG® Precision
HD 720p and TANDBERG Precision HD 1080p
Thin Profile Wall Mount for Sony EVI-HD7V
Pan/Tilt/Zoom Camera - Black
Fits TANDBERG Precision HD 720p
and TANDBERG Precision HD 1080p
Fits Sony EVI-HD7V and Sony EVI-HD3V
• Heavy-gauge
steel
hardware included
• Mounts to drywall or 2-gang electrical box
• Heavy gauge steel construction
• Mounting
• Mounting hardware included
• Mounts to drywall or 2-gang electrical box
Thin Profile Wall Mount for Sony EVI‑HD7V
535‑2000‑232
Thin Profile Wall Mount Bracket for TANDBERG Precision
HD720p and TANDBERG Precision HD 1080p
535‑2000‑217
Thin Profile Wall Mount Bracket
for TANDBERG Set-top Codecs
Thin Profile Wall Mount Bracket for LifeSize® HD Camera
Fits LifeSize HD Camera
• Heavy
gauge steel construction
hardware included
• Mounts to drywall or 2-gang electrical box
Fits TANDBERG Set-top Codecs
• Mounting
• Welded aluminum construction strength
• Cables and connectors concealed from view
Thin Profile Wall Mount Bracket for LifeSize HD Camera
535‑2000‑222
• Mounting hardware included
Thin Profile Wall Mount Bracket
for TANDBERG Set‑top Codecs
535‑2000‑250
Thin Profile Wall Mount Bracket
for TANDBERG WAVE II or Polycom PowerCam
Thin Profile Wall Mount Bracket for LifeSize 10X Camera
Wall mount for LifeSize 10x camera (Black)
• Mounting
Fits TANDBERG WAVE II or Polycom PowerCam
hardware included
Thin Profile Wall Mount for LifeSize 10x Camera
535‑2000‑234
• Mounting
hardware included
• Mounts to drywall or 2-gang electrical box
Thin Profile Wall Mount Bracket for TANDBERG WAVE II or
Polycom PowerCam
535‑2000‑219
Thin Profile Wall Mount Bracket for Polycom VSX Codecs
IN–Wall for LifeSize 10X Camera
Fits VSX-7000, VSX-6000 and VSX-5000 Codecs
Recessed camera enclosure for LifeSize 10x camera
only
• Fits
Polycom VSX Set-top Codecs
• Heavy gauge steel construction
• Mounting hardware included
• Mounts to drywall or 2-gang electrical box
• Includes
IN‑Wall for LifeSize 10x Camera
999‑2225‑220
Thin Profile Wall Mount Bracket
for Polycom VSX Codecs
535‑2000‑220
Thin Profile Wall Mount Bracket
for Polycom EagleEye/EagleEye II
Fits Polycom EagleEye/EagleEye II
• Heavy
gauge steel construction
hardware included
• Mounts to drywall or 2-gang electrical box
metal back box enclosure and face frame
camera platform for rigidity and strength
• Reinforced
IN–Wall Enclosure for Videoconferencing Cameras
The IN-Wall Enclosure for the Polycom EagleEye, LifeSize HD and TANDBERG Precision HD
Cameras is designed and sized to fit the entire PTZ camera system including the camera
and its respective cabling systems.
• Fits
Polycom EagleEye/EagleEye II, LifeSize HD and TANDBERG
Precision HD 720 and TANDBERG Precision HD 1080
• Includes metal back box enclosure, camera platform and face frame
• Reinforced camera platform for rigidity and strength
• Powder coated white
• Mounting
Thin Profile Wall Mount Bracket
for Polycom EagleEye/EagleEye II
535‑2000‑221
Thin Profile Wall Mount for Sony EVI-HD3V
Pan/Tilt/Zoom Camera - Black
Fits Sony EVI-HD3V and Sony EVI-HD7V
• Heavy-gauge
steel
hardware included
• Mounts to drywall or 2-gang electrical box
• Mounting
IN‑Wall
Polycom
EagleEye
999‑2225‑015
IN‑Wall
for LifeSize HD
999‑2225‑015
IN‑Wall
TANDBERG
Precision HD Cameras
999‑2225‑015
Thin Profile Wall Mount for Sony EVI‑HD3V
535‑2000‑232
Note: Cameras and EZCamera shoes not included.
Call 800-572-2011 Toll Free
vaddio.com
39
Document Cameras
CeilingVIEW HD-18 DocCAM™
CeilingVIEW SD
The CeilingVIEW SD is a standard definition ceilingmounted document system equipped with a highresolution 1/4-inch color CCD camera with a 36x
optical zoom lens. The camera has VISCA camera
control capabilities allowing control via codecs and
other VISCA-based control systems.
The CeilingVIEW HD-18 DocCAM is a high definition
ceiling-mounted document camera system capable
of 16:9 resolutions at 1080p, 1080i and 720p, and
4:3 resolutions at 480i and 576i. The 18x optical
zoom lens and 1.3 megapixel 1/3-Type CCD image
sensor provide precise color reproduction and edge
focus, essential for displaying images on a largeformat HD monitor or for transmitting critical images
through an HD videoconferencing system.
CeilingVIEW HD-18 DocCAM
North America
999-3018-000
International
999-3018-001
F E At u r E S
CCD Image Device
• 18x Lens
• Component HD
(1080p, 1080i or 720p) outputs
• 1.3 Megapixel
• Metal back box enclosure with tile support braces
and trim ring
• Includes PowerRite power supply, IR remote and AC cord set
• 1/3-Type
CeilingVIEW SD uses HSDS, allowing the integrator
to run power, video and camera control on Cat. 5
cabling up to 400 feet.
CeilingVIEW SD
NtSC
999-2008-000
PAL
999-2008-001
F E At u r E S
Color CCD Image Device
• 36x Lens
• Y/C and composite output
• Metal back box enclosure with tile support braces and trim
ring
• Laser light locator for document positioning
• Quick-Connect CeilingVIEW HD/SD Interface
• Includes PowerRite power supply, IR Remote and EZCamera
Control Adapter
• Compatible with Polycom and TANDBERG IR remotes (zoom)
• 1/4-inch
CeilingVIEW HD-18 DocCAM DVI/HDMI
The CeilingVIEW HD-18 DocCAM DVI/HDMI is a high
definition ceiling-mounted document camera system
capable of 16:9 resolutions at 1080p, 1080i and
720p, and 4:3 resolutions at 480i and 576i. The 18x
optical zoom lens and 1.3 megapixel 1/3-Type CCD
image sensor provide precise color reproduction
and edge focus, essential for displaying images on
a large-format HD monitor or for transmitting critical
images through an HD videoconferencing system.
CeilingVIEW SD CCU Image Controller
CeilingVIEW SD CCU enables the adjustment of color, gain and iris functions on the camera
with the turn of a knob. User-defined adjustments may be stored using two Scene buttons.
Match color-critical documents for those applications where color accuracy is a must.
The CeilingVIEW HD-18 DocCAM DVI/HDMI delivers
simultaneous analog component video (YPbPr) and
digital video (DVI-D or HDMI) outputs on separate
connectors, up to 100 feet over a single Cat. 5 cable.
CeilingVIEW HD-18 DocCAM
DVI/HDMI
North America
999-3028-001
International
999-3028-001
F E At u r E S
CCD Image Device
• 18x Lens
• Simultaneous Analog Component HD (YPbPr)
and Digital video (DVI/HDMI) outputs
• 1.3 Megapixel
• Metal back box enclosure with tile support braces
and trim ring
• Includes PowerRite power supply, IR remote and AC cord set
• 1/3-Type
Optional CCU Image Controller
for CeilingVIEW HD-18 DocCAM Series
CeilingVIEW SD CCu
North America
999-2009-000
F E At u r E S
and blue gain, aperture, iris and gain controls
• Red
International
999-2009-001
Optional Recessed Installation Kit
for CeilingVIEW HD-18 DocCAM
The CCU Image Controller enables the adjustment of color, gain, pedestal, gamma, chroma,
knee and iris functions on the camera with the turn of a knob. These controls allow the
camera to deliver a more accurate representation of the image that is being captured and
color match and shade multiple cameras.
Optional CeilingVIEW HD-18
DocCAM CCu Image Controller
999-1105-023
40
F E At u r E S
in conjunction with Quick-Connect SR or QuickConnect DVI/HDMI SR Interfaces
• Controls scenes, red & blue gain, detail, chroma, gamma,
pedestal, knee, iris and gain
• For North America and International Markets
• Works
Optional recessed Installation Kit
for CeilingVIEW HD-18 DocCAM
998-2225-052
F E At u r E S
mounting CeilingVIEW HD-18 DocCAM in Gypsum Board
or Hard Ceilings
• Includes: mounting plates, larger white trim ring and
mounting hardware
• For North America and International Markets
• For
Call 800-572-2011 Toll Free
vaddio.com
IN-Wall Camera Mounts
The Vaddio IN-Wall camera mounting systems are an attractive way to mount PTZ cameras on a wall where room
aesthetics are critical. These mounting systems use the depth of the wall cavity to recess the camera into the wall,
minimizing the camera’s extension into the room and providing a finished look to the installation.
IN-Wall™ Enclosure for Vaddio ClearVIEW
HD-20, HD-19 and HD-18
IN–Wall Enclosure for Sony EVI–HD1
The IN-Wall Enclosure for the Sony EVI-HD1 is designed and
sized to fit the entire PTZ camera system including the camera,
EZIM and dongle to enable the use of Cat. 5 cabling.
The IN-Wall Enclosure for the Vaddio ClearVIEW
HD-20, HD-19 and HD-18 is designed and sized to fit
the entire PTZ camera system including the camera,
EZIM and dongle to enable the use of Cat. 5 cabling.
• Fits
IN-Wall for
Sony EVI-HD1
999-2225-014
Sony EVI-HD1, WallVIEW PRO HD1
and WallVIEW CCU HD1
• Includes metal back box enclosure, camera platform and face frame
• Reinforced camera platform for rigidity and strength
• Powder coated white
IN–Wall Enclosure for Sony BRC–300
IN-Wall Enclosure
for Vaddio ClearVIEW HD-20,
HD-19 & HD-18
999-2225-018
• Fits ClearVIEW HD-20/HD-19/HD-18, WallVIEW HD-20/
HD-19/HD-18 SR, WallVIEW CCU HD-20/HD-19/HD-18,
WallVIEW CCU HD-20/HD-19/HD-18 SDI, and WallVIEW
HD-20/HD-19/HD-18 DVI/HDMI
• Includes metal back box enclosure, camera platform
and face frame
• Reinforced camera platform for rigidity and strength
• Powder coated white
IN–Wall Enclosure for Sony BRC–H700
The IN-Wall Enclosure for the Sony BRC-H700 is
designed and sized to fit the entire PTZ camera
system including the camera, EZIM and dongle to
enable the use of Cat. 5 cabling.
• Fits
IN-Wall for
Sony BRC-H700
999-2225-016
Sony BRC-H700, WallVIEW PRO H700
and WallVIEW CCU H700
• Includes metal back box enclosure, camera platform
and face frame
• Reinforced camera platform for rigidity and strength
• Powder coated white
The IN-Wall Enclosure for the Sony BRC-300 is designed and
sized to fit the entire PTZ camera system.
• Fits
Sony BRC-300
metal back box enclosure, camera platform
and face frame
• Powder coated white
• Includes
IN-Wall for
Sony BRC-300
999-2225-013
IN-Wall Enclosure
for Sony EVI-D70 and Canon VC-C50i
The IN-Wall Enclosure for the Sony EVI-D70 and Canon
VC-C50i is designed and sized to fit the entire PTZ camera
system including the camera and EZCamera Cable Shoe to
enable the use of Cat. 5 cabling.
• Fits
Sony EVI-D70 and Canon VC-C50i
metal back box enclosure, camera platform
and face frame
• Reinforced camera platform for rigidity and strength
• Powder coated white
IN–Wall Enclosure for Sony BRC–Z700
The IN-Wall Enclosure for the Sony BRC-Z700 is
designed and sized to fit the entire PTZ camera
system including the camera, EZIM and dongle to
enable the use of Cat. 5 cabling.
Fits Sony BRC-Z700, WallVIEW PRO Z700 and WallVIEW
CCU Z700
• Includes metal back box enclosure, camera platform and
face frame
• Reinforced camera platform for rigidity and strength
• Powder coated white
•
IN-Wall for
Sony BRC-Z700
999-2225-017
• Includes
IN-Wall for Sony EVI-D70 /
Canon VC-C50i
999-2225-012
IN–Wall Enclosure for Sony EVI–D100
IN–Wall Enclosure for Sony BRC–Z330
The IN-Wall Enclosure for the Sony EVI-D100 is designed and
sized to fit the entire PTZ camera system including the camera
and EZCamera Cable Shoe to enable the use of Cat. 5 cabling.
The IN-Wall Enclosure for the Sony BRC-Z330 is
designed and sized to fit the entire PTZ camera
system including the camera, EZIM and dongle to
enable the use of Cat. 5 cabling.
• Fits
IN-Wall for
Sony BRC-Z330
999-2225-019
Sony BRC-Z330, WallVIEW PRO Z330 and WallVIEW
CCU Z330
• Includes metal back box enclosure, camera platform and
face frame
• Reinforced camera platform for rigidity and strength
• Powder coated white
Call 800-572-2011 Toll Free
vaddio.com
• Fits
In-WALL for
Sony EVI-D100
999-2225-011
Sony EVI-D100, WallVIEW 100 and Model 100 PTZ
metal back box enclosure, camera platform and face frame
• Reinforced camera platform for rigidity and strength
• Powder coated white
• Includes
41
Ceiling Mounts
Off-Set Drop Down Mount for Vaddio ClearVIEW
HD-20, HD-19 and HD-18
Drop Down Mount for Small PTZ Cameras
– Short (12-inch)
Fits ClearVIEW HD-20/HD-19/HD-18-, WallVIEW HD20/HD-19/HD-18 SR, WallVIEW CCU HD-20/HD-19/
HD-18, WallVIEW CCU HD-20/HD-19/HD-18 SDI and
WallVIEW HD-20/HD-19/HD-18 DVI/HDMI
Fits Vaddio Model 50, 70 and 100 PTZ Cameras
• Also
compatible with Polycom PowerCam,
TANDBERG WAVE II and LifeSize PTZ Cameras
• Heavy gauge steel construction
• Extends approx. 1 foot below ceiling
• Drywall
or suspended ceiling installation
gauge steel construction
• Extends approx. 28 inches below ceiling
• Heavy
Off-Set Drop Down Mount
for Vaddio ClearVIEW HD-20, HD-19 and HD-18
535-2000-296
Drop Down Mount
for Small PtZ Cameras - Short
535-2000-290
Drop Down Mount for Small PTZ Cameras
– Long (24-inch)
Fits Vaddio Model 50, 70 and 100 PTZ Cameras
Off – Set Drop Down Mount for Panasonic HE100
Fits Panasonic AW-HE100, WallVIEW CCU HE100 and
WallVIEW PRO HE100
• Also
compatible with Polycom PowerCam,
TANDBERG WAVE II and LifeSize PTZ Cameras
• Heavy gauge steel construction
• Extends approx. 2 feet below ceiling
• 1-inch
NPT pipe thread connects to third-party
mounting hardware
• Heavy gauge steel construction
• Extends approx. 28 inches below ceiling
Drop Down Mount
for Small PtZ Cameras - Long
535-2000-291
Off-Set Drop Down Mount
for Panasonic HE100
535-2000-295
Drop Down Mount for Large PTZ Cameras
Off – Set Drop Down Mount for Sony BRC Cameras
– Long (24-inch)
Fits Sony HD1, WallVIEW PRO HD1,
WallVIEW CCU HD1
Fits Sony BRC Cameras, PRO and CCU H700, Z700,
Z330 and 300 systems
• Also
compatible with Polycom EagleEye
and TANDBERG Precision HD
• Heavy gauge steel construction
• Extends approx. 2 feet below ceiling
• 1-inch
NPT pipe thread connects to third-party
mounting hardware
• Heavy gauge steel construction
• Extends approx. 28 inches below ceiling
Off-Set Drop Down Mount
for Sony BrC Cameras
535-2000-294
Drop Down Mount
for Large PtZ Cameras - Long
535-2000-293
Drop Down Mount for Large PTZ Cameras
– Short (12-inch)
Fits Sony HD1, WallVIEW PRO HD1,
WallVIEW CCU HD1
• Also
compatible with Polycom EagleEye
and TANDBERG Precision HD
• Heavy gauge steel construction
• Extends approx. 1 foot below ceiling
Suspended CeilingPTZ Camera Mount for a Vaddio
ClearVIEW HD-20, HD-19, HD-18, Sony Model 70 or Canon Model 50iR
Drop Down Mount for Large PtZ Cameras - Short
535-2000-292
Fits ClearVIEW HD-20/19/18, WallVIEW SR HD-20/19/18, WallVIEW CCU SDI HD-20/19/18,
WallVIEW DVI/HDMI HD-20/19/18. Sony Model 70 and Canon Model 50iR
• Drywall
or suspended ceiling installation
gauge steel construction
• Extends approx. 28 inches below ceiling
Drop Down Coupler Kit for Large/Small Platform Mounts
• Heavy
Suspended Ceiling PtZ Camera Mount
535-2000-206
Drop Down Coupler Kit
535-2000-299
For use with 535-2000-290, 535-2000-291,
535-2000-292, 535-2000-293 and 535-2000-296
• Coupler can interface
with third-party mounting hardware
Note: Cameras not included.
42
Call 800-572-2011 Toll Free
vaddio.com
Wall Mounts
Model HD-20, HD-19 and HD-18
Thin Profile Wall Mount Bracket
Model HE100 Wall Mount Bracket
Fits Panasonic AW-HE100
• Heavy-gauge
steel
hardware included
• Mounts to drywall or 3-gang electrical box
Fits Vaddio ClearVIEW HD-20, HD-19 and HD-18
• Mounting
• Heavy-gauge
steel
hardware included
• Mounts to drywall or 2-gang electrical box
• Mounting
Model HE100 Wall Mount Bracket
535-2000-229
Model HD-19 and HD-18 thin Profile Wall Mount Bracket
535-2000-230 (Black)
535-2000-230W (White)
Model HD-20 thin Profile Wall Mount Bracket
535-2020-230 (Black)
Model Z700 Wall Mount Bracket
Fits Sony BRC-Z700
• Heavy-gauge
steel
hardware included
• Mounts to drywall or 3-gang electrical box
• Mounting
Model H700 Wall Mount Bracket
Model Z700 Wall Mount Bracket
535-2000-225
Fits Sony BRC-H700
• Heavy-gauge
steel
hardware included
• Mounts to drywall or 3-gang electrical box
• Mounting
Model 300 Thin Profile Wall Mount Bracket
Fits Sony BRC-300
Model H700 Wall Mount Bracket
535-2000-223
• Heavy-gauge
steel
hardware included
• Mounts to drywall or 3-gang electrical box
• Mounting
Model Z330 Wall Mount Bracket
Model 300 thin Profile Wall Mount Bracket
535-2000-208
Fits Sony BRC-Z330
• Mounting
• Mounts
hardware included
to drywall or 3-gang electrical box
Model Z330 Wall Mount Bracket
535-2000-231
Wall Mount for Canon BU – 50/51H
Includes the adapter plate for mounting the
BU-50/51H to the Wall Mount. Not intended for use
with the Canon BU-45/46H Outdoor PTZ Camera.
Model HD1 Thin Profile Wall Mount Bracket
Wall Mount for Canon Bu-50/51H
998-4150-001
Fits Sony EVI-HD1
• Heavy-gauge
steel
• Mounting hardware included
• Mounts to drywall or 2-gang electrical box
Model HD1 thin Profile Wall Mount Bracket
535-2000-216
Pedestal Mount for Canon BU – 50/51H
Includes the adapter plate for mounting the
BU-50/51H to the Wall Mount. Not intended for use
with the Canon BU-45/46H Outdoor PTZ Camera.
Model 70 Thin Profile Wall Mount Bracket
Fits Sony EVI-D70 (Platinum White) 535-2000-205
Fits Sony EVI-D70 (Black) 535-2000-205B
Pedestal Mount for Canon Bu-50/51H
998-4150-002
• Mounting
• Mounts
hardware included
to drywall or 2-gang electrical box
Model 70 thin Profile Wall Mount Bracket
535-2000-205 (White)
Standard Tube Camera Mounts
535-2000-204B (Black)
Tubular, aluminum wall/ceiling mounts allow for easy cable management pass-through.
They come in silver/gray finish with 1/4-inch, 20 thread mounting screws.
Model 100 Thin Profile Wall Mount Bracket
Fits Sony EVI-D100 (Platinum White) 535-2000-204
Fits Sony EVI-D100 (Black) 535-2000-204B
• Mounting
hardware included
• Mounts to drywall or 2-gang electrical box
Model 100 thin Profile Wall Mount Bracket
535-2000-204 (White)
535-2000-204B (Black)
Standard Camera Mount
535-2000-212
Length: 12 inches (305mm) to
18.3 inches (465mm)
Expandable Wall Mount
535-2000-214
Length: 12 inches (305mm) to
18.3 inches (465mm)
Model 50i Thin Profile Wall Mount Bracket – Black
Long Expandable Wall/
Ceiling Mount
535-2000-215
Fits Canon VC-C50i
• Mounting
• Mounts
hardware included
to drywall or 2-gang electrical box
Model 50i thin Profile Wall Mount Bracket - Black
535-2000-207
Call 800-572-2011 Toll Free
vaddio.com
universal Wall/Ceiling Mount
535-2000-213
Length:
24 inches (610mm) to
40 inches (1016mm)
Dimensions: 9.5 inches x 8 inches (242mm x 203mm)
43
Dome Camera Systems
Dome systems provide integrators with a secure camera housing designed to protect PTZ cameras against damage
that can be caused when cameras are exposed to the elements and vandalism.
DomeVIEW HD Indoor Flush Mount Dome Kit
for HD-20, HD-19 and HD-18
DomeVIEW 70 Flush Mount Camera System
Flush Mount Dome Enclosure and Sony EVI-D70 PTZ
camera with EZCamera Cabling System. The Domes
are formed with optical-grade polycarbonate and are
available in clear (standard) or smoked tint (optional).
The Indoor Flush Mount Dome Kit for Vaddio’s ClearVIEW HD-20, HD-19 or HD-18 provides
a secure housing solution for high definition PTZ cameras. The clear and smoked optically
correct domes provide for distortion-free viewing that allows the camera operator to
position the camera anywhere within its pan/tilt range.
The Indoor Flush Mount Dome kit includes a 12-inch
(30.48 cm) clear flush mount dome enclosure and
internal brackets to support the Vaddio ClearVIEW
HD-20/19/18 cameras.
F e at u r e s
clear optical-grade polycarbonate dome
• Metal back can
• One-piece tile support brace
• White trim ring and mounting hardware
• Conduit connector and seismic hanger plate
• 12-inch
Indoor Flush Mount Dome for
Vaddio HD‑20/HD‑19/HD‑18
998‑9000‑200
DomeVIeW 70 Flush Mount
Camera system
North america Only
999‑9000‑070
DomeVIEW 70 Indoor Pendant Camera System
Indoor Pendant Mount Dome Enclosure and Sony
EVI-D70 PTZ camera with EZCamera Cabling
System. The Domes are formed with optical-grade
polycarbonate and are available in clear (standard) or
smoked tint (optional).
**Camera not included
DomeVIEW HD Indoor Pendant Mount Dome Kit
for HD-20, HD-19 and HD-18
The Indoor Pendant Mount Dome Kit for Vaddio’s ClearVIEW HD-20, HD-19 or HD-18
provides a secure housing solution for high definition PTZ cameras. The clear and smoked
optically correct domes provide for distortion-free viewing that allows the camera operator
to position the camera anywhere within its pan/tilt range.
The Indoor Pendant Mount Dome kit includes a 12-inch
(30.48 cm) optical-grade polycarbonate clear dome
enclosure and internal brackets to support the Vaddio
ClearVIEW HD-20/19/18 cameras.
Indoor Pendant
Mount Dome for
Vaddio HD‑20/HD‑19/HD‑18
998‑9100‑200
F e at u r e s
• 12-inch clear optical-grade polycarbonate dome
• Light gray UV-treated plastic shroud
• Metal back can
• 1.5-inch NPT pipe adapter and gasket
• Stainless steel screws for dome attachment
• Mounting hardware
**Camera not included
DomeVIEW HD Outdoor Weather-Resistant (Light Duty)
Pendant Mount for HD-20, HD-19 and HD-18
The Outdoor Weather-Resistant Pendant Mount Dome Kit for Vaddio’s ClearVIEW HD-20,
HD-19 or HD-18 provides a secure housing solution for high definition PTZ cameras. The
clear and smoked optically correct domes provide for distortion-free viewing that allows
the camera operator to position the camera anywhere within its pan/tilt range.
The Outdoor Pendant Mount Dome kit includes a
12-inch (30.48 cm) optical-grade polycarbonate
smoke-tinted dome enclosure and internal brackets
to support the Vaddio ClearVIEW HD-20/19/18
cameras.
F e at u r e s
smoke-tinted optical-grade polycarbonate dome
• Light gray UV-treated plastic shroud
• Metal back can
• 1.5-inch NPT pipe adapter and gasket
• Stainless steel screws for dome attachment
• Heater/Blower
• Mounting hardware
• 12-inch
Outdoor Pendant Mount Dome for
Vaddio HD‑20/HD‑19/HD‑18
998‑9200‑200
**Camera not included
44
F e at u r e s
7.3-inch (18.54cm) clear dome with white twist-and-lock trim ring
• Plenum-rated metal back box
(tile support brace recommended)
• Includes Sony EVI-D70 PTZ Camera
(90 degree tilt, 340 degree pan)
• Sony EVI-D70 Bracket included
•
F e at u r e s
•7.3-inch (18.54cm) clear dome with white twist-and-lock trim ring
DomeVIeW 70 Indoor Pendant
Camera system
North america Only
999‑9100‑070
• White, high-impact plastic pendant enclosure
with 1-inch NPT fitting
Sony EVI-D70 PTZ Camera (90° tilt, 340° pan)
• Sony EVI-D70 Bracket included
• Includes
DomeVIEW 70 Outdoor Pendant Dome Camera System
Outdoor Pendant Dome Enclosure and Sony EVI-D70
PTZ camera with EZCamera Cabling System. The Domes
are formed with optical-grade polycarbonate and are
available in clear (standard) or smoked tint (optional).
F e at u r e s
(20.8cm) smoke-tinted dome
• Dual shell construction
with integrated 1.5-inch NPT pendant mount
• Heater and blower kit with 24 Volt AC power supply
• Includes Sony EVI-D70 PTZ Camera (90° tilt, 340° pan)
• Sony EVI-D70 Bracket included
• 8.2-inch
DomeVIeW 70 Outdoor
Pendant Dome Camera system
North america Only
999‑9200‑070
Tile Support Brace for DomeVIEW HD Flush Mount Domes
• 23.75-inch
• Serves
(60.33cm) aluminum tile brace
as template and brace
tile support Brace for DomeVIeW HD Flush Mount Domes
997‑9000‑000
12" Clear Dome Accessory (dome only)
Clear replacement dome for DomeVIEW HD Outdoor Pendant Dome with
stainless steel screws for Vaddio HD-20/HD-19/HD-18.
Clear Dome Option for Vaddio
998‑9000‑210
12" Smoke Tinted Dome Accessory (dome only)
Smoke tinted replacement dome for DomeVIEW HD Outdoor Pendant Dome
with stainless steel screws for Vaddio HD-20/HD-19/HD-18.
smoke tinted Dome Option for Vaddio
998‑9000‑220
Call 800-572-2011 Toll Free
vaddio.com
Dome Camera Systems
DomeVIEW 50iR Flush Mount Camera System
Flush Mount Dome Enclosure and Canon VC-C50iR
PTZ Camera with EZCamera Cabling System. The
Domes are formed from optical-grade polycarbonate
and are available in clear (standard) or smoked tint
(optional).
F E At u r E S
• 7.3-inch (18.54cm) clear dome
with white twist-and-lock trim ring
• Plenum-rated metal back box
(tile support brace recommended)
• Includes Canon VC-C50iR PTZ Camera (90° tilt, 340° pan)
• Canon VC-C50iR Bracket included
• Includes EZCamera Cabling System
DomeVIEW 50ir
Flush Mount Camera System
North America Only
999-9000-050
DomeVIEW 50iR Indoor Pendant Camera System
Indoor Pendant Mount Dome Enclosure and Canon
VC-C50iR PTZ Camera with EZCamera Cabling
System. The Domes are formed from optical-grade
polycarbonate and are available in clear (standard) or
smoked tint (optional).
DomeVIEW 50ir Indoor Pendant
Camera System
North America Only
999-9100-050
F E At u r E S
• 7.3-inch (18.54cm) clear dome
with white twist-and-lock trim ring
• White, high-impact plastic pendant enclosure
with 1-inch NPT fitting
• Includes Canon VC-C50iR PTZ Camera
(90 degree tilt, 340 degree pan)
• Canon VC-C50iR Bracket included
• Includes EZCamera Cabling System
Flush Mount Dome and Bracket
for Sony EVI-D70 or for Canon VC-C50iR
Includes a 7.3-inch (18.54cm) clear flush mount
dome enclosure and internal brackets to support the
Sony EVI-D70 or Canon VC-C50iR.
F E At u r E S
Flush Mount
Dome for
Sony EVI-D70
998-9000-070
Outdoor Pendant Dome Enclosure and Canon
VC-C50iR PTZ Camera with EZCamera Cabling
System. The Domes are formed from optical-grade
polycarbonate and are available in clear (standard) or
smoked tint (optional).
F E At u r E S
(20.8cm) smoke-tinted dome
• Dual shell construction
with integrated 1.5-inch NPT pendant mount
• Heater and blower kit with 24 Volt AC power supply
• Includes Canon VC-C50iR PTZ Camera
(90 degree tilt, 340 degree pan)
• Canon VC-C50iR Bracket included
• Includes EZCamera Cabling System
• 8.2-inch
DomeVIEW & DomeVIEW HD Wall Mounting Kits
for Indoor and Outdoor Pendant Domes
F E At u r E S
aluminum cast construction
• 1.5-inch NPT threads easily onto domes
• 85 mph (136.8kph) wind rating
• Heavy-duty
Wall Mount with Pole Mounting Kit
for Indoor and Outdoor Pendant Domes
998-9300-001
Call 800-572-2011 Toll Free
vaddio.com
(tile support brace recommended)
**Camera not included
Flush Mount Dome for
Canon VC-C50ir
998-9000-050
Sony EVI-D70 Bracket included 998-9000-070
Canon VC-C50iR Bracket included 998-9000-050
Indoor Pendant Dome and Bracket
for Sony EVI-D70 or for Canon VC-C50iR
Includes a 7.3-inch (18.54cm) clear pendant dome
enclosure and internal brackets to support the Sony
EVI-D70 or the Canon VC-C50iR.
Indoor Pendant
Dome and
Bracket for
Sony EVI-D70
998-9100-070
Indoor Pendant Dome and
Bracket for
Canon VC-C50ir
998-9100-050
F E At u r E S
(18.54cm) clear dome
with white twist-and-lock trim ring
• White, high-impact plastic pendant enclosure
with 1-inch NPT fitting
• 7.3-inch
**Camera not included
Sony EVI-D70 Bracket included 998-9000-070
Canon VC-C50iR Bracket included 998-9000-050
Outdoor Pendant Dome
Pendant Dome Camera System
Wall Mounting Kit
for Indoor and Outdoor
Pendant Domes
998-9300-000
with white twist-and-lock trim ring
• Plenum-rated metal back box
for Sony EVI-D70 or Canon VC-C50iR
DomeVIEW 50iR Outdoor
DomeVIEW 50ir Outdoor
Pendant Dome Camera System
North America Only
999-9200-050
• 7.3-inch (18.54cm) clear dome
Ceiling Mounting Kit
for Indoor and Outdoor
Pendant Domes
998-9300-002
Outdoor Pendant
Dome with
Bracket
for Sony EVI-D70
998-9200-070
Outdoor Pendant
Dome with Bracket
for Canon VC-C50ir
998-9200-050
Includes an 8.2-inch (20.8cm) smoke-tinted
pendant dome enclosure and internal brackets to
support the Sony EVI-D70 or the Canon 50iR.
F E At u r E S
(20.8cm) smoke-tinted dome
• Dual shell construction
with integrated 1.5-inch NPT pendant mount
• Heater and blower kit with 24 Volt AC power supply
• 8.2-inch
**Camera not included
Clear or Smoke Tinted Replacement Dome
Options for DomeVIEW Outdoor Pendant Dome
Clear Dome Option for Outdoor
Pendant Domes
997-9200-082
Smoke tinted Dome Option for
Outdoor Pendant Domes
997-9200-083
• Stainless
steel screws
OPtIONS
8.2-inch (20.8cm) clear replacement dome
997-9200-082
8.2-inch (20.8cm) smoke-tinted replacement dome
997-9200-083
Smoke Tinted Dome Option for DomeVIEW Indoor
Pendant Series and Flush Mount Domes
7.3-inch Smoke tinted Dome
Option for Flush Mount or Indoor
Pendant Dome Enclosures
997-9000-073
7.3-inch Clear Dome Option for
Flush Mount or Indoor Pendant
Dome Enclosures
997-9000-074
• Stainless
steel screws
OPtIONS
7.3-inch (18.54cm) smoke-tinted replacement dome
997-9000-073
7.3-inch (18.54cm) clear Dome Replacement
for Flush Mount or Indoor Pendant Dome
997-9000-074
45
Vaddio
9433 Science Center Drive
Minneapolis, MN 55428
800-572-2011 Toll Free
vaddio.com
©2011 All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing subject to change. Vaddio, OneLINK, AutoTrak,
REVEAL, ClearVIEW HD‑20, ClearVIEW HD‑19, ClearVIEW HD‑18, Squiggle, Squiggle Board, Squiggle IP, ProductionVIEW, PreVIEW, TeleTouch, TrackVIEW, AutoTrak, EZCamera,
ControlVIEW, MicVIEW, TouchVIEW, AutoVIEW, StepVIEW, Quick‑Connect, PowerRite, WallVIEW, IN‑Wall, CoverVIEW, CeilingVIEW, DocCAM, HideAway, UXHD CrossPoint, AutoPresenter,
PresenterPOD, IN‑Ceiling, and DomeVIEW are registered trademarks of Vaddio.
All other trademarks are property of their respective owners.
Form Number 1037/6‑11