Avigilon 16L-H4PRO-B Installation guide

Installation Guide
Avigilon High Definition Professional IP
Camera Models:
16L-H4PRO-B, 12L-H4PRO-B and 8L-H4PRO-B
920-0078A-Rev1
This manual provides installation and operation information and
precautions for the use of this camera. Incorrect installation could
cause an unexpected fault. Before installing this equipment read this
manual carefully. Please provide this manual to the owner of the
equipment for future use.
The Warning symbol indicates the presence of
dangerous voltage within and outside the product
enclosure that may constitute a risk of electric shock,
serious injury or death to persons if proper precautions
are not followed.
The Caution symbol alerts the user to the presence of
hazards that may cause minor or moderate injury to
persons, damage to property or damage to the product
itself if proper precautions are not followed.
Warning — Failure to observe the following instructions may
result in severe injury or death.
•
•
•
•
Do not use near water or expose to dripping or splashing.
Do not place objects filled with liquids above the device.
Do not expose to rain or moisture.
For indoor use only.
If used outdoors, an approved outdoor mounting adapter
or enclosure is required. Consult with Avigilon for more
information.
•
Installation must be performed by qualified personnel only,
and must conform to all local codes.
This product is intended to be supplied by a UL Listed
Power Unit marked “Class 2” or “LPS” or “Limited Power
Source” with output rated 12 VDC or 24 VAC, 10 W min. or
Power over Ethernet (PoE), rated 48 VDC, 10 W min.
•
i
English
Important Safety Information
•
English
•
Any external power supply connected to this product may
only be connected to another Avigilon product of the same
model series. External power connections must be
properly insulated.
Do not connect directly to mains power for any reason.
Caution — Failure to observe the following instructions may
result in injury or damage to the camera.
•
•
•
•
•
•
•
•
•
•
•
•
ii
Do not install near any heat sources such as radiators, heat
registers, stoves, or other sources of heat.
Do not subject the cables to excessive stress, heavy loads
or pinching.
Do not open or disassemble the device. There are no user
serviceable parts.
Refer all servicing to qualified personnel.
Servicing may be required when the device has been
damaged (such as from a liquid spill or fallen objects), has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Do not use strong or abrasive detergents when cleaning
the device body.
Use only accessories recommended by Avigilon.
Use only UL-listed mounting bracket suitable for the
mounting surface and minimum 0.4 kg (0.9 lb) weight, plus
the weight of the attached lens.
Avoid leaving the image sensor exposed for extended
periods of time. Always cover the image sensor with either
a lens or a dust cap.
Do not allow dust, moisture or any other foreign debris to
enter the lens mount.
Never touch any glass elements inside the lens mount.
Do not point the lens directly at the sun or other extremely
bright objects or damage to the image sensor may occur.
Use of controls or adjustments or performance of
procedures other than those specified in this document
may result in hazardous radiation exposure.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Notice
This equipment has been tested and found to comply with the limits for
a Class B computing device pursuant to Subpart B of Part 15 of FCC
rules, which are designed to provide reasonable protection against
such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause
interference, in which case the user at his/her own expense will be
required to take whatever measures may be required to correct the
interference.
Changes or modifications made to this equipment not expressly
approved by Avigilon Corporation or parties authorized by Avigilon
Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please dispose
of it according to your local environmental laws and guidelines.
Risk of fire, explosion, and burns. Do not disassemble, crush, heat
above 100 °C (212 °F), or incinerate.
iii
English
Regulatory Notices
European Union:
English
This symbol means that according to local laws and
regulations your product should be disposed of
separately from household waste. When this product
reaches its end of life, take it to a collection point
designated by local authorities. Some collection points
accept products for free. The separate collection and
recycling of your product at the time of disposal will help
conserve natural resources and ensure that it is recycled
in a manner that protects human health and the
environment.
Legal Notices
© 2014 Avigilon Corporation. All rights reserved. Unless expressly
granted in writing, no license is granted with respect to any copyright,
industrial design, trademark, patent or other intellectual property rights
of Avigilon Corporation or its licensors.
This manual has been compiled and published covering the latest
product descriptions and specifications. The contents of this manual
and the specifications of this product are subject to change without
notice. Avigilon reserves the right to make changes without notice in
the specifications and materials contained herein and shall not be
responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to
typographical and other errors relating to the publication.
AVIGILON, CAPTURE IT WITH CLARITY, HDSM, HIGH DEFINITION
STREAM MANAGEMENT (HDSM), THE BEST EVIDENCE and
LIGHTCATCHER are unregistered and/or registered trademarks of
Avigilon Corporation in Canada and other jurisdictions worldwide.
Other product names mentioned herein may be the unregistered and/
or registered trademarks of their respective owners. ™ and ® are not
used in association with each trademark in this document.
iv
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Required Tools and Materials . . . . . . . . . . . . . . . . . . . . 3
Camera Package Contents . . . . . . . . . . . . . . . . . . . . . . 3
Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Mounting the Lens . . . . . . . . . . . . . . . . . . . . . . . . 4
Mounting the Camera . . . . . . . . . . . . . . . . . . . . 5
Connecting Cables . . . . . . . . . . . . . . . . . . . . . . 6
Assigning an IP Address. . . . . . . . . . . . . . . . . . 6
Accessing the Live Video Stream . . . . . . . . . . . 7
Aiming and Focusing the Camera. . . . . . . . . . . 7
(Optional) Configuring Onboard Storage. . . . 8
For More Information. . . . . . . . . . . . . . . . . . . . . 9
Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . .10
Connecting External Power . . . . . . . . . . . . . . . . . . . . . 10
Connecting to External Devices . . . . . . . . . . . . . . . . . . 11
Connecting to Microphones and Speakers . . . . . . . 12
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Reset to Factory Default Settings . . . . . . . . . . . .14
Setting the IP Address Through the
ARP/Ping Method . . . . . . . . . . . . . . . . . . . . . . . . . .15
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Image Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Limited Warranty & Technical Support . . . . . . . .19
English
Table of Contents
English
English
Overview
Front View
Lens Release Button
Lens Mount
EF-S mount index
EF mount index
Feature
Description
Lens Mount
Accepts EF and EF-S lenses.
Lens Release
Button
Releases the lens that is mounted on the camera.
EF-S mount
index
A white mark on the lens mount to help you align
an EF-S lens to the camera.
EF mount index
A red mark on the lens mount to help you align an
EF lens to the camera.
1
Rear View
English
Camera Mounts
(top and bottom)
SD Card Slot
I/O
Connector
Block
Power Connector
Block
Ethernet Port
Link LED
Connection Status LED
Serial Number
Tag
Audio I/O
Connector
Feature
Description
Camera Mounts
Provides mounting points for the camera. Mounts accept 1/4”-20
UNC bolts commonly found on tripods and mounting brackets.
SD Card Slot
Accepts an SD card for onboard storage. See (Optional) Configuring
Onboard Storage for more information.
Power Connector
Block
Accepts a terminal block with either AC or DC power connection. DC
input can be either polarity. Only required when Power over Ethernet
is not available.
Ethernet Port
Accepts an Ethernet connection to a network. Server communication
and image data transmission occurs over this connection. Also
receives power when it is connected to a network that provides
Power over Ethernet.
Connection Status Provides information about device operation. See LED indicators for
LED
more information.
Link LED
Indicates if there is an active connection in the Ethernet port.
I/O Connector
Block
Provides connections to external input/output devices. See
Connecting to External Devices for more information.
Serial Number Tag Product serial number and part number label.
Audio I/O
Connector
2
Accepts a mini-jack connector (3.5 mm). See Connecting to
Microphones and Speakers for more information.
English
Installation
Required Tools and Materials
•
EF or EF-S mount lens
•
Small slotted screwdriver with 5/64” or 2 mm blade width
— for connecting power when not using Power over
Ethernet.
•
Mounting bracket, enclosure or tripod.
Camera Package Contents
Ensure the package contains the following:
•
Avigilon High Definition IP Camera
•
Power terminal block
•
Dust cap
•
I/O terminal block
Installation Steps
Complete the following procedures to install the camera.
1.
2.
3.
4.
5.
6.
7.
Mounting the Lens on page 4
Mounting the Camera on page 5
Connecting Cables on page 6
Assigning an IP Address on page 6
Accessing the Live Video Stream on page 7
Aiming and Focusing the Camera on page 7
(Optional) Configuring Onboard Storage on page 8
3
Mounting the Lens
English
Important: Avigilon cameras require high-quality lenses to take full
advantage of their advanced imaging capabilities. To avoid poor image
quality caused by incorrect lens selection, only use lenses that are
recommended by Avigilon for use with this camera model. For a list of
lenses recommended for use with this camera model, contact your
Avigilon dealer or representative.
NOTE: If the lens includes a collar, the collar must be used to prevent
damage to the lens mount on the camera.
To mount a lens to the camera, complete the following steps:
1.
2.
3.
4.
If the lens includes a collar, install the collar to the lens first.
Remove the dust cap from the lens mount.
Align the lens to the appropriate index marker on the lens
mount.
•
Red mark: EF mount index
•
White mark: EF-S mount index
Turn the lens clockwise until it locks into place.
To detach a lens, complete the following steps:
1.
2.
While pressing the lens release button, turn the lens
counterclockwise until it stops.
Remove the lens from the camera.
Immediately mount another lens or a dust cap on the lens mount to
prevent contamination.
4
English
Caution —
•
Never touch the image sensor or any glass
elements inside the lens mount. Only clean the
image sensor with the recommended cleaning
tools. See Cleaning for more information.
•
Do not allow dust, moisture or any other foreign
debris to enter the lens mount.
•
Avoid leaving the image sensor exposed for
extended periods of time.
•
Always cover the image sensor with either a lens
or a dust cap.
Mounting the Camera
1.
Use the ¼”-20 UNC threaded holes to mount the camera
on to a bracket, tripod or in an enclosure as required.
•
Mount the camera using the tripod collar on the
lens.
•
If the lens does not have a tripod collar, use the
threaded holes at the top and bottom of the camera.
Consult the installation instructions provided with the bracket, tripod or
enclosure for detailed mounting instructions.
Caution — Always mount the camera from the lens tripod
collar when the lens includes a collar.
Warning — Use only UL-listed mounting bracket suitable for
the mounting surface and minimum 0.37 kg (0.8 lb) weight
plus the weight of the attached lens.
5
Connecting Cables
English
Refer to the diagrams in the Overview section for the location of the
different connectors.
To connect the cables required for proper operation, complete the
following:
1.
2.
3.
4.
If there are external input or output devices that need to be
connected to the camera (for example: door contacts,
relays, etc), connect the devices to the camera I/O
Terminals.
For more information, see Connecting to External Devices.
If an external microphone or speaker needs to be
connected to the camera, connect the devices to the
camera audio connector.
For more information, see Connecting to Microphones and
Speakers.
Connect a network cable to the camera’s Ethernet Port
(RJ-45 connector).
•
The Link LED will turn on once a network link has
been established.
Connect power using one of the following methods:
•
Power over Ethernet (PoE) Class 3 — If PoE is
available, the camera LEDs will turn on.
•
5.
External Power — Connect an external 12 VDC or 24
VAC power source to the power connector block.
For more information, see Connecting External
Power.
Check that the Connection Status LED indicates the correct
state.
For more information, see LED Indicators.
Assigning an IP Address
The camera automatically obtains an IP address by default. Once
connected to a network, it attempts to locate and obtain an IP address
6
The IP address settings can be changed using one of the following
methods:
•
Avigilon Camera Installation Tool software application.
•
Camera's web browser interface:
http://<camera IP address>/
•
ARP/Ping method. For more information, see Setting the IP
Address through the ARP/Ping Method.
•
Network Video Management software application (for
example, Avigilon Control Center).
NOTE: The default camera username is admin and the default
password is admin.
Accessing the Live Video Stream
Live video stream can be viewed using one of the following methods:
•
Avigilon Camera Installation Tool software application.
•
Camera's web browser interface:
http://<camera IP address>/.
•
Network Video Management software application (for
example, Avigilon Control Center).
NOTE: The default camera username is admin and the default
password is admin.
Aiming and Focusing the Camera
Use the Avigilon Camera Installation Tool or camera web interface to
aim and focus the camera. Consult the software user guide for more
information.
1.
If available, adjust the zoom using the appropriate ring on
the lens.
7
English
from a DHCP server. If this fails, Zero Configuration Networking
(Zeroconf) is used to choose an IP address. When the IP address is set
using Zeroconf, the IP address is in the 169.254.0.0/16 subnet.
2.
English
If the lens has an auto focus (AF) mode, set the lens switch
to the AF position to allow the camera web interface or
Avigilon Camera Installation Tool to control the camera’s
focus.
a.
In the Image and Display settings page, use the
Auto Focus button to focus the lens.
b.
If the desired focus position was not achieved, use
the focus near and far buttons to adjust the focus.
(Optional) Configuring Onboard Storage
To use the camera’s onboard storage feature, you must insert an SD
card into the SD card slot.
It is recommended that the SD card have a capacity of 64 GB or more,
and a write speed of class 10 or better. If the SD card does not meet the
recommended capacity or write speed, the performance of the
onboard storage may suffer and result in the loss of frames or footage.
Ensure the SD card is designed for continuous video recording or the
SD card life expectancy may be adversely affected.
1.
Insert an SD card into the camera.
Caution — Do not force the SD card into the camera or you
may damage the card and the camera. The SD card can only
be inserted in the direction shown on the camera.
2.
Access the camera’s web interface to enable the onboard
storage feature.
For more information, see the Avigilon High Definition
H.264 Camera Web Interface User Guide.
8
English
For More Information
Additional information about setting up and using the device is
available in the following guides:
•
Avigilon Camera Installation Tool User Guide
•
Avigilon Control Center Client User Guide
•
Avigilon High Definition H.264 Web Interface User Guide
The manuals are available on the Avigilon website: http://avigilon.com/
support-and-downloads.
9
English
Cable Connections
Connecting External Power
NOTE: Do not perform this procedure if Power over Ethernet (POE) is
used.
If PoE is not available, the camera needs to be powered through the
removable power connector block. Refer to the diagrams in this guide
for the location of the power connector block.
The device can be powered from 12 VDC or 24 VAC. The power
consumption information is listed in the product specifications.
To connect power to the power connector block, complete the
following steps:
1.
2.
Remove the power connector block from the device.
Remove the insulation from ¼” (6 mm) of the power wires.
Do not nick or damage the wires.
3.
Insert the two power wires into the two terminals on the
power connector block. The connection can be made with
either polarity.
Use a small slotted (5/64” or 2 mm blade width)
screwdriver to loosen and tighten the terminals.
4.
Attach the power connector block back into the receptacle
on the device.
Warning — This product is intended to be supplied by a UL
Listed Power Unit marked “Class 2” or “LPS” or “Limited
Power Source” with output rated 12 VDC or 24 VAC, 10 W
min. or PoE rated 48 VDC, 10 W min.
10
External devices are connected to the camera through the I/O terminal.
The pinout for the I/O terminal is shown in the following table and
diagram.
Table: External I/O Connector
Pin
Description
1
Ground
2
RS-485B
3
RS-485A
4
Relay input
5
Relay output
6
+5 VDC, 200 mA max. output for relay drive
NOTE: The 5 V connection can be used to energize a relay coil with up
to 200 mA. If more than 200 mA is required, an external power
supply up to 25 VDC at 120 mA can be used.
SWITCH
External Device
B
1
2
A
3
RS-485
GND
RELAY
3.3V
4
5
6
25 V
120 mA MAX
GND
5V
200 mA MAX
GND
Figure: External I/O schematics and example application.
11
English
Connecting to External Devices
Connecting to Microphones and Speakers
English
The camera can be connected to an external microphone and speaker
through the audio connector. The connector is a mini-jack (3.5 mm),
and the pinout for it is shown in the following diagram.
NOTE: The camera only supports line level mono audio input.
Audio OUT
Audio IN
Figure: Mini-jack audio connector.
12
GND
GND
Once the camera is connected to the network, the Connection Status
LED will display the camera’s progress in connecting to the Network
Video Management software.
The following table describes what the LEDs indicate:
Table:LED Indicators
Connection
State
Connection
Status LED
Description
Obtaining IP One short
Address
flash every
second
Attempting to obtain an IP address.
Discoverable Two short
flashes every
second
Obtained an IP address but is not
connected to the Network Video
Management software.
Upgrading
Firmware
Two short
Updating the firmware.
flashes and
one long flash
every second
Connected
On
Connected to the Network Video
Management software.
13
English
LED Indicators
English
Reset to Factory Default
Settings
If the camera no longer functions as expected, you can choose to
restore the camera to its factory default settings.
Use the firmware revert button to reset the camera.
Firmware Revert Button
Figure: The firmware revert microswitch on the rear of the camera.
1.
Disconnect power from the camera.
2.
Using a straightened paperclip or similar tool, gently press
and hold the firmware revert button.
While continuing to hold the button, power the device.
Release the button after three seconds.
3.
Caution — Do not apply excessive force. Inserting the tool
too far will damage the device.
14
Complete the following steps to configure the camera to use a specific
IP address:
1.
2.
Locate and copy down the MAC Address (MAC) listed on
the Serial Number Tag for reference.
Open a Command Prompt window and enter the following
commands:
a.
arp -s <New Camera IP Address> <Camera
MAC Address>
For example: arp -s 192.168.1.10 00-1885-12-45-78
b.
3.
4.
ping -l 123 -t <New Camera IP Address>
For example: ping -l 123 -t 192.168.1.10
Reboot the camera.
Close the Command Prompt window when you see the
following message:
Reply from <New Camera IP Address>: ...
15
English
Setting the IP Address Through
the ARP/Ping Method
English
Cleaning
Image Sensor
The image sensor is protected from contamination by protective glass.
However, the protective glass can be contaminated by dust and other
debris.
To clean the protective glass, perform the following steps:
1.
2.
3.
Remove the lens or dust cap.
Using a photographic-grade bulb-type blower
(commercially available), blow away any dust or foreign
debris from the protective glass inside the lens mount.
Immediately replace the lens or dust cap.
If the protective glass is still not clean, obtain an image sensor cleaning
swab and solution. Follow the cleaning instructions provided by the
manufacturer.
Avigilon recommends using the Type 2 Sensor Swab™ and Eclipse®
cleaning solution made by Photographic Solutions, Inc. For a
worldwide list of dealers, visit the Photographic Solutions, Inc. website
at www.photosol.com.
Caution —
16
•
Never touch the image sensor or any glass
elements inside the lens mount. Only clean the
image sensor with the recommended cleaning
tools. See Cleaning for more information.
•
Do not allow dust, moisture or any other foreign
debris to enter the lens mount.
•
Avoid leaving the image sensor exposed for
extended periods of time.
•
Always cover the image sensor with either a lens
or a dust cap.
English
Body
Use a dry or lightly dampened cloth to clean the camera body.
Caution — Do not use strong or abrasive detergents when
cleaning the camera body.
17
English
Specifications
Camera
Audio Input/Output
Line level, mini-jack (3.5 mm)
Onboard Storage
SD/SDHC/SDXC slot - minimum class 6; class 10, 64GB or better
recommended
Network
Network
100Base-TX
Cabling Type
CAT5
Connector
RJ-45
Security
Password protection, HTTPS encryption, digest authentication, WS
authentication, user access log
Protocols
IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP, UDP, IGMP,
ICMP, DHCP, Zeroconf, ARP
Streaming Protocols
RTP/UDP, RTP/UDP multicast, RTP/RTSP/TCP, RTP/RTSP/HTTP/TCP,RTP/
RTSP/HTTPS/TCP, HTTP
Mechanical
Dimensions L x W x H
109 mm x 73 mm x 68 mm
4.3” x 2.9” x 2.7”
Weight
0.37 kg (0.8 lbs)
Camera Mount
¼”-20 UNC (top and bottom)
Electrical
Power Consumption
10 W — camera only
Power Source
VDC: 12 V +/-10%, 10 W
VAC: 24 V +/-10%, 14.3 VA
PoE: IEEE802.3af Class 3 compliant
Power Connector
2-pin terminal block
Environmental
Operating Temperature
-10 °C to +50 °C (14 °F to 122 °F)
Storage Temperature
-10 °C to +70 °C (14 °F to 158 °F)
Certifications
Safety
UL 60950
CE
CSA 60950
ROHS
Electromagnetic
Emissions
FCC Part 15 Subpart B Class B
EN 55022 Class B
Electromagnetic Immunity EN 55024 Class B
EN 61000-4-4 EN 61000-4-5
18
EN 60950-1
WEEE
IC ICES-003 Class B
EN 61000-4-2
EN 61000-4-6
EN 61000-4-3
EN 61000-4-11
English
Limited Warranty & Technical
Support
Avigilon warrants to the original consumer purchaser, that this product will
be free of defects in material and workmanship for a period of 3 years from
date of purchase.
The manufacturer’s liability hereunder is limited to replacement of the
product, repair of the product or replacement of the product with repaired
product at the discretion of the manufacturer. This warranty is void if the
product has been damaged by accident, unreasonable use, neglect,
tampering or other causes not arising from defects in material or
workmanship. This warranty extends to the original consumer purchaser of
the product only.
AVIGILON DISCLAIMS ALL OTHER WARRANTIES EXPRESSED OR IMPLIED
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EXCEPT
TO THE EXTENT THAT ANY WARRANTIES IMPLIED BY LAW CANNOT BE
VALIDLY WAIVED.
No oral or written information, advice or representation provided by Avigilon,
its distributors, dealers, agents or employees shall create another warranty
or modify this warranty. This warranty states Avigilon’s entire liability and
your exclusive remedy against Avigilon for any failure of this product to
operate properly.
In no event shall Avigilon be liable for any indirect, incidental, special,
consequential, exemplary, or punitive damages whatsoever (including but
not limited to, damages for loss of profits or confidential or other information,
for business interruption, for personal injury, for loss of privacy, for failure to
meet any duty including of good faith or of reasonable care, for negligence,
and for any other pecuniary or other loss whatsoever) arising from the use of
or inability to use the product, even if advised of the possibility of such
damages. Since some jurisdictions do not allow the above limitation of
liability, such limitation may not apply to you.
This Limited Warranty gives you specific legal rights and you may also have
other rights which vary from jurisdiction to jurisdiction.
Warranty service and technical support can be obtained by
contacting Avigilon Technical Support by phone at 1.888.281.5182 or
via email at support@Avigilon.com.
19