Ricoh AP400 Operating instructions

Operating Instructions
Printer Reference
1
Setting Up the Printer Driver and Canceling a Print Job
2
Uninstalling the Printer Driver and Software
3
Paper and Other Media
4
Sample Print/Locked Print
5
Troubleshooting
6
Making Printer Settings with the Control Panel
7
Appendix
For safety, please read this manual carefully before you use this product and keep it handy
for future reference.
Introduction
This manual gives detailed instructions and notes on the operation and maintenance of this machine.
To get maximum versatility from this machine all operators are requested to read this manual carefully
and follow its instructions. Please keep this manual in a handy place near the machine.
Please read the Safety Information before using this machine. It contains important information related
to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be liable for direct, indirect, special, incidental, or consequential damages as a result of handling or operating the machine.
Caution:
Use of controls or adjustment or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Do not attempt any Maintenance or troubleshooting other than that mentioned in this manual. This
printer contains a laser beam generator and direct exposure to laser beams can cause permanent eye
damage.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
For good print quality, the supplier recommends that you use genuine toner from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products.
TABLE OF CONTENTS
Trademarks.............................................................................................................1
Manuals for This Printer........................................................................................ 3
Manuals for This Printer ............................................................................................. 3
How to Read This Manual .....................................................................................4
1. Setting Up the Printer Driver and Canceling a Print Job
PCL 6/5e - Accessing the Printer Properties....................................................... 5
Windows 95/98/Me - Accessing the Printer Properties .............................................. 5
Windows 2000/Windows XP/Server 2003 - Accessing the Printer Properties ........... 6
Windows NT 4.0 - Accessing the Printer Properties .................................................. 9
RPCS - Accessing the Printer Properties .......................................................... 11
Windows 95/98/Me - Accessing the Printer Properties ............................................ 11
Windows 2000/Windows XP/Server 2003 - Accessing the Printer Properties .........13
Windows NT 4.0 - Accessing the Printer Properties ................................................ 16
PostScript - Setting Up for Printing ................................................................... 18
Windows 95/98/Me - Accessing the Printer Properties ............................................ 18
Windows 2000/Windows XP/Server 2003 - Accessing the Printer Properties .........19
Windows NT 4.0 - Accessing the Printer Properties ................................................ 22
Macintosh - Setting Up for Printing ..........................................................................24
Canceling a Print Job ..........................................................................................25
Windows 95/98/Me, Windows 2000, Windows XP/Server 2003,
Windows NT 4.0 - Canceling a Print Job ............................................................... 25
Macintosh - Canceling a Print Job ........................................................................... 26
2. Uninstalling the Printer Driver and Software
Uninstalling the PCL 6/5e Printer Driver............................................................ 29
Windows 95/98/Me - Uninstalling the PCL 6/5e Printer Driver.................................29
Windows 2000/Windows XP/Server 2003 - Uninstalling the PCL 6/5e Printer Driver ...29
Windows NT 4.0 - Uninstalling the PCL 6/5e Printer Driver.....................................30
Uninstalling the RPCS Printer Driver .................................................................31
Windows 95/98/Me - Uninstalling the RPCS Printer Driver...................................... 31
Windows 2000/Windows XP/Server 2003 - Uninstalling the RPCS Printer Driver...31
Windows NT 4.0 - Uninstalling the RPCS Printer Driver ..........................................32
Uninstalling the PostScript Printer Driver .........................................................33
Windows 95/98/Me - Uninstalling the PostScript Printer Driver ...............................33
Windows 2000/Windows XP/Server 2003 - Uninstalling the PostScript Printer Driver ...33
Windows NT 4.0 - Uninstalling the PostScript Printer Driver ................................... 34
Macintosh - Uninstalling the PostScript Printer Driver .............................................34
i
3. Paper and Other Media
Paper and Other Media Supported by This Printer...........................................35
Paper Types and Sizes ............................................................................................35
Paper Recommendations.........................................................................................42
Printable Area .......................................................................................................... 45
Loading Paper and Other Media......................................................................... 47
Loading Paper in the Paper Tray .............................................................................47
Loading Paper in the Bypass Tray ........................................................................... 50
Loading Envelopes...................................................................................................55
4. Sample Print/Locked Print
Sample Print .........................................................................................................61
Printing a Sample Print File......................................................................................62
Deleting a Sample Print File..................................................................................... 63
Checking the Error Log ............................................................................................65
Locked Print .........................................................................................................66
Printing a Locked Print File ......................................................................................66
Deleting the Locked Print File .................................................................................. 68
Checking the Error Log ............................................................................................70
5. Troubleshooting
Error & Status Messages on the Control Panel ................................................73
Getting Printer Information over the Network ...........................................................83
Printer Does Not Print ......................................................................................... 89
Other Printing Problems .....................................................................................93
Removing Misfed Paper ...................................................................................... 97
When “Remove Misfeed Paper Tray” Appears ........................................................ 97
When "Remove Misfeed Internal Path/Open Front Cover" Appears........................98
When "Remove Misfeed Paper Exit Cover" Appears............................................... 99
When "Remove Misfeed Duplex Unit" Appears .....................................................104
Replacing the Toner Cartridge ......................................................................... 107
Cleaning and Adjusting the Printer.................................................................. 110
Cleaning the Friction Pad.......................................................................................110
Cleaning the Paper Feed Roller............................................................................. 111
Cleaning the Registration Roller ............................................................................ 113
Adjusting the Image Density .................................................................................. 114
Adjusting the Registration of the Trays ..................................................................116
ii
6. Making Printer Settings with the Control Panel
Menu Chart ......................................................................................................... 119
Accessing the Main Menu ................................................................................. 122
Paper Input Menu............................................................................................... 124
Paper Input Parameters ......................................................................................... 124
Changing the Paper Input Menu ............................................................................ 126
List/Test Print Menu........................................................................................... 128
List/Test Print Parameters...................................................................................... 128
Printing the Configuration Page and Error Log ...................................................... 129
Printing a Configuration Page ................................................................................ 130
Interpreting the Configuration Page .......................................................................132
Maintenance Menu............................................................................................. 134
Maintenance Menu Parameters ............................................................................ 135
Changing the Maintenance Menu .......................................................................... 137
System Menu...................................................................................................... 146
System Parameters................................................................................................146
Changing the System Menu................................................................................... 151
Host Interface Menu........................................................................................... 154
Host Interface Parameters ....................................................................................154
Changing the Host Interface Menu ........................................................................160
PCL Menu ........................................................................................................... 162
PCL Parameters..................................................................................................... 162
Changing the PCL Menu........................................................................................164
PS Menu.............................................................................................................. 166
PS Parameters.......................................................................................................166
Changing the PS Menu ..........................................................................................167
PDF Menu ........................................................................................................... 169
PDF Parameters ....................................................................................................169
Changing the PDF Menu........................................................................................169
Language Menu.................................................................................................. 172
Changing the Language Menu............................................................................... 172
iii
7. Appendix
Replacing Parts.................................................................................................. 175
MAINTENANCE KIT Type 400 ..............................................................................175
Replacing the Friction Pad .....................................................................................177
Replacing the Paper Feed Rollers ......................................................................... 178
Replacing the Transfer Roller ................................................................................ 179
Replacing the Fusing Unit ...................................................................................... 182
Collate ................................................................................................................. 184
Spool Printing .................................................................................................... 185
Precautions when using Windows Server 2003.............................................. 186
Precautions when using the Terminal Server mode .............................................. 186
Memory Capacity and Paper Size..................................................................... 187
Setting of the “Frame Priority” ................................................................................ 187
Setting of the “Font Priority” ................................................................................... 188
Moving and Transporting the Printer............................................................... 189
Moving the Printer .................................................................................................. 189
Specifications..................................................................................................... 191
Mainframe .............................................................................................................. 191
Options...................................................................................................................194
Consumables ..................................................................................................... 198
Information about Installed Software............................................................... 199
expat ......................................................................................................................199
JPEG LIBRARY ..................................................................................................... 199
NetBSD .................................................................................................................. 200
INDEX....................................................................................................... 202
iv
Trademarks
AppleTalk, EtherTalk, LaserWriter, Macintosh are registered trademarks of Apple Computer, Inc.
Ethernet is a registered trademark of Xerox Corporation.
Microsoft, Windows, Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Novell, NetWare are registered trademarks of Novell, Inc.
PostScript is a registered trademark of Adobe Systems, Incorporated.
PowerPC is a registered trademark of International Business Machines Corporation.
PCL is a registered trademark of Hewlett-Packard Company.
Bluetooth is a Trademark of the Bluetooth SIG, Inc. (Special Interest Group) and
licensed to RICOH Company Limited.
Copyright © 2001 Bluetooth SIG, Inc.
The Bluetooth Trademarks are owned by Bluetooth SIG, Inc. USA
Other product names used herein are for identification purposes only and might
be trademarks of their respective companies. We disclaim any and all rights to
those marks.
The proper names of the Windows operating systems are as follows:
• The product name of Windows® 95 is Microsoft® Windows 95.
• The product name of Windows® 98 is Microsoft® Windows 98.
• The product name of Windows® Me is Microsoft® Windows Millennium Edition (Windows Me).
• The product names of Windows® 2000 are as follows:
Microsoft® Windows® 2000 Advanced Server
Microsoft® Windows® 2000 Server
Microsoft® Windows® 2000 Professional
• The product names of Windows® XP are as follows:
Microsoft® Windows® XP Professional
Microsoft® Windows® XP Home Edition
• The product names of Windows ServerTM 2003 are as follows:
Microsoft® Windows ServerTM 2003 Standard Edition
Microsoft® Windows ServerTM 2003 Enterprise Edition
Microsoft® Windows ServerTM 2003 Web Edition
• The product names of Windows NT® 4.0 are as follows:
Microsoft® Windows NT® Server 4.0
• Microsoft® Windows NT® Workstation 4.0
1
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.
2
Manuals for This Printer
Manuals for This Printer
The following manuals describe the operational procedures and Maintenance of
this machine.
To enhance safe and efficient operation of this printer, all users should read and
follow the instructions carefully.
❖ Quick Installation Guide
Describes how to install the printer.
❖ Setup Guide
Provides information about setting up the printer and its options. This manual is provided as a printed manual, and also on the CD-ROM labeled "Operating Instructions".
❖ Printer Reference (this manual)
Provides information about using the printer and its options. This manual
provided on the CD-ROM labeled “Operating Instructions”.
❖ Network Printing Guide
Provides information about setting up and using the printer in a network environment. This manual provided on the CD-ROM labeled “Operating Instructions”.
❖ PostScript 3 Operating Instructions Supplement
Describes the menus and features for the PostScript 3 printer driver. This
manual provided on the CD-ROM labeled “Operating Instructions”.
Note
❒ There are three CD-ROMs that come with this printer. “Operating Instructions”, “Printer Drivers and Utilities”, and “Document Management Utility”.
❒ Concerning UNIX information, please visit our Web site or consult your authorized reseller.
3
How to Read This Manual
Symbols
In this manual, the following symbols are used:
R WARNING:
This symbol indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
R CAUTION:
This symbol indicates a potentially hazardous situation which, if instructions
are not followed, may result in minor or moderate injury or damage to property.
* The statements above are notes for your safety.
Important
If this instruction is not followed, paper might be misfed, originals might be
damaged, or data might be lost. Be sure to read this.
Preparation
This symbol indicates the prior knowledge or preparations required before operating.
Note
This symbol indicates precautions for operation, or actions to take after misoperation.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions in which a particular function cannot be used.
Reference
This symbol indicates a reference.
[
]
Keys that appear on the machine's panel display.
Keys and buttons that appear on the computer's display.
{
}
Keys built into the machine's control panel.
Keys on the computer's keyboard.
4
1. Setting Up the Printer Driver
and Canceling a Print Job
PCL 6/5e - Accessing the Printer Properties
Windows 95/98/Me - Accessing the Printer Properties
There are two methods you can use to open the printer properties dialog box.
Changing the default printer settings
Note
❒ With some applications, the printer driver's settings are not used, and the application's own default settings are applied.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Properties].
The Printer Properties appear.
D Make any settings you require and click [Apply].
E Click [OK].
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• PCL 6
DRIVERS\PCL6\WIN9X_ME\(Language)\DISK1
• PCL 5e
DRIVERS\PCL5e\WIN9X_ME\(Language)\DISK1
5
Setting Up the Printer Driver and Canceling a Print Job
Making printer settings from an application
To make the printer settings for a specific application, open the [Printer Properties]
dialog box from that application. The following example describes how to make
settings for the WordPad application that comes with Windows 95/98/Me.
1
Note
❒ The actual procedure you should follow to open the [Printer Properties] dialog
box may differ depending on the application. For more information, see the
documentation that comes with the application you are using.
❒ With some applications, the printer driver's settings are not used, and the application's own default settings are applied.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print].
The [Print] dialog box appears.
B Select the printer you want to use in the [Name] list box, and then click [Properties].
The [Printer Properties] dialog box appears.
C Make any settings you require and click [OK].
D Click [OK] to start printing.
Windows 2000/Windows XP/Server 2003 - Accessing the Printer
Properties
Changing the default printer settings - Printer Properties
Limitation
❒ Changing the setting of the printer requires Manage Printers permission.
Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account
that has Manage Printers permission.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
6
Note
❒ With Windows XP Professional/Windows Server 2003, access the [Printers
and Faxes] window from [Start] on the taskbar.
❒ With Windows XP Home Edition, open [Control panel] from [Start], click
[Printers and Other Hardware], and then click [Printers and Faxes] on the screen
that appears.
PCL 6/5e - Accessing the Printer Properties
B Click to select the icon of the printer whose default setting you want to
change.
C On the [File] menu, click [Properties].
1
The Printer Properties appear.
Note
❒ When you open the printer properties dialog box for the first time after installing the RPCS printer driver, a confirmation window appears. After
that, the initial display of the printer properties dialog box appears.
D Make any settings you require and click [OK].
Note
❒ Settings you make here are used as the default settings for all applications.
E Click [OK].
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• PCL 6
DRIVERS\PCL6\WIN2K_XP\(Language)\DISK1
• PCL 5e
DRIVERS\PCL5e\WIN2K_XP\(Language)\DISK1
Changing the default printer settings – Printing Preferences Properties
Limitation
❒ Changing the setting of the printer requires Manage Printers permission.
Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account
that has Manage Printers permission.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
7
Setting Up the Printer Driver and Canceling a Print Job
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Printing Preferences...].
1
The Printing Preferences Properties appears.
D Make any settings you require and click [Apply].
Note
❒ Settings you make here are used as the default settings for all applications.
E Click [OK].
Making printer settings from an application
To make the printer settings for a specific application, open the [Print] dialog box
from that application. The following example describes how to make settings for
the WordPad application that comes with Windows 2000/Windows XP/Server
2003.
Note
❒ The actual procedures you should follow to open the [Print] dialog box may
differ depending on the application. For more information, see the documentation that comes with the application you are using.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print...].
The [Print] dialog box appears.
B Select the printer you want to use in the [Select Printer] box.
Click the tab that you want to change its print setting.
Note
❒ With Windows XP/Server 2003, click [Preference] to open the Printer Preference window.
C Make any settings you require and click [Apply].
Note
❒ With Windows XP/Server 2003, make any settings you require and click
[OK].
D Click [Print] to start printing.
8
PCL 6/5e - Accessing the Printer Properties
Windows NT 4.0 - Accessing the Printer Properties
Changing the default printer settings - Printer Properties
1
Limitation
❒ Changing the setting of the printer requires Full Control access permission.
Members of Administrators, Server Operators, Print Operators, and Power
Users groups have Full Control permission by default. When you set up options, log on using an account that has Full Control permission.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
Note
❒ When you open the printer properties dialog box for the first time after installing the RPCS printer driver, a confirmation window appears. After
that, the initial display of the printer properties dialog box appears.
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Properties].
The Printer Properties appears.
D Make any settings you require and click [OK].
Note
❒ Settings you make here are used as the default settings for all applications.
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• PCL 6
DRIVERS\PCL6\NT4\(Language)\DISK1
• PCL 5e
DRIVERS\PCL5e\NT4\(Language)\DISK1
9
Setting Up the Printer Driver and Canceling a Print Job
Changing the default printer settings – Default Document Properties
Limitation
❒ Changing the setting of the printer requires Full Control access permission.
Members of the Administrators, Server Operators, Print Operators, and Power Users groups have Full Control permission by default. When you set up
options, log on using an account that has Full Control permission.
1
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Document Defaults].
The Default Document Properties appear.
D Make any settings you require and click [OK].
Note
❒ Settings you make here are used as the default settings for all applications.
Making printer settings from an application
To make the printer settings for a specific application, open the [Printer Properties]
dialog box from that application. The following example describes how to make
settings for the WordPad application that comes with Windows NT 4.0.
Note
❒ The actual procedure you should follow to open the [Printer Properties] dialog
box may differ depending on the application. For more information, see the
documentation that comes with the application you are using.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print].
The [Print] dialog box appears.
B Select the printer you want to use in the [Name] list box, and then click [Properties].
The Printer Properties appears.
C Make any settings you require and click [OK].
Click [OK] to start printing.
10
RPCS - Accessing the Printer Properties
RPCS - Accessing the Printer Properties
Windows 95/98/Me - Accessing the Printer Properties
1
There are two windows types you can use to open the printer properties dialog
box.
“Multi-tab” is used as an example in this manual. See Help for information
about changing the windows types.
❖ Multi-tab
This is the window type for users who often change print settings in order to
make various kinds of prints.
❖ Custom Setting
This is the window type for users who rarely change print settings when making prints. The Custom Setting display may vary depending on the installed
options.
Changing the default printer settings
To make default printer settings, first open the printer properties dialog box
from the [Printers] window.
Note
❒ With some applications, printer driver settings are not used, and the application's own default settings are applied.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Properties].
The printer properties appear.
Note
❒ When you open the printer properties dialog box for the first time after installing the RPCS printer driver, a confirmation window appears. After
that, the initial display of the printer properties dialog box appears.
D Make any settings you require and click [Apply].
Note
❒ With some applications, the printer driver's settings are not used, and the
application's own default settings are applied.
E Click [OK].
11
Setting Up the Printer Driver and Canceling a Print Job
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• RPCS
DRIVERS\RPCS\WIN9X_ME\(Language)\DISK1
1
Making printer settings from an application
To make the printer settings for a specific application, open the [Printer Properties]
dialog box from that application. The following example describes how to make
settings for the WordPad application that comes with Windows 95/98/Me.
Note
❒ The actual procedure you should follow to open the [Printer Properties] dialog
box may differ depending on the application. For more information, see the
documentation that comes with the application you are using.
❒ With some applications, printer driver settings are not used, and the application's own default settings are applied.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print].
The [Print] dialog box appears.
B Select the printer you want to use in the [Name] list box, and then click [Properties].
The [Printer Properties] dialog box appears.
C Make any settings you require and click [OK].
D Click [OK] to start printing.
12
RPCS - Accessing the Printer Properties
Windows 2000/Windows XP/Server 2003 - Accessing the Printer
Properties
1
Changing the default printer settings - Printer Properties
Limitation
❒ Changing the setting of the printer requires Manage Printers permission.
Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account
that has Manage Printers permission.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
Note
❒ With Windows XP Professional/Windows Server 2003, access the [Printers
and Faxes] window from [Start] on the taskbar.
❒ With Windows XP Home Edition, open [Control panel] from [Start], click
[Printers and Other Hardware], and then click [Printers and Faxes] on the screen
that appears.
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Properties].
The Printer Properties appears.
Note
❒ When you open the printer properties dialog box for the first time after installing the RPCS printer driver, a confirmation window appears. After
that, the initial display of the printer properties dialog box appears.
D Make any settings you require and click [Apply].
Note
❒ Settings you make here are used as the default settings for all applications.
E Click [OK].
13
Setting Up the Printer Driver and Canceling a Print Job
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• RPCS
DRIVERS\RPCS\WIN2K_XP\(Language)\DISK1
1
Changing the default printer settings - Printing Preferences Properties
Limitation
❒ Changing the setting of the printer requires Manage Printers permission.
Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account
that has Manage Printers permission.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Printing Preferences...].
The Printing Preferences Properties appear.
D Make any settings you require and click [Apply].
Note
❒ Settings you make here are used as the default settings for all applications.
E Click [OK].
14
RPCS - Accessing the Printer Properties
Making printer settings from an application
To make the printer settings for a specific application, open the [Print] dialog box
from that application. The following example describes how to make settings for
the WordPad application that comes with Windows 2000.
1
Note
❒ The actual procedures you should follow to open the [Print] dialog box may
differ depending on the application. For more information, see the documentation that comes with the application you are using.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print...].
The [Print] dialog box appears.
B Select the printer you want to use in the [Select Printer] box.
Click the tab that you want to change its print setting.
Note
❒ With Windows XP/Server 2003, click [Preference] to open the Printer Preference window.
C Make any settings you require and click [Apply].
Note
❒ With Windows XP/Server 2003, make any settings you require and click
[OK].
D Click [Print] to start printing.
15
Setting Up the Printer Driver and Canceling a Print Job
Windows NT 4.0 - Accessing the Printer Properties
Changing the default printer settings - Printer Properties
1
Limitation
❒ Changing the setting of the printer requires Full Control access permission.
Members of Administrators, Server Operators, Print Operators, and Power
Users groups have Full Control permission by default. When you set up options, log on using an account that has Full Control permission.
A Click [Start] on the taskbar, point to [[Settings]], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer you want to use.
C On the [File] menu, click [Properties].
The [Printer Properties] dialog box appears.
Note
❒ When you open the printer properties dialog box for the first time after installing the RPCS printer driver, a confirmation window appears. After
that, the initial display of the printer properties dialog box appears.
D Make any settings you require and click [OK].
Note
❒ Settings you make here are used as the default settings for all applications.
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• RPCS
DRIVERS\RPCS\NT4\(Language)\DISK1
16
RPCS - Accessing the Printer Properties
Changing the default printer settings – Default Document Properties
Limitation
❒ Changing the setting of the printer requires Full Control access permission.
Members of the Administrators, Server Operators, Print Operators, and Power Users groups have Full Control permission by default. When you set up
options, log on using an account that has Full Control permission.
1
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer you want to use.
C On the [File] menu, click [Document Defaults].
The Default Document Properties appear.
D Make any settings you require and click [OK].
Note
❒ Settings you make here are used as the default settings for all applications.
Making printer settings from an application
To make the printer settings for a specific application, open the [Printer Properties]
dialog box from that application. The following example describes how to make
settings for the WordPad application that comes with Windows NT 4.0.
Note
❒ The actual procedure you should follow to open the [Printer Properties] dialog
box may differ depending on the application. For more information, see the
documentation that comes with the application you are using.
❒ With some applications, printer driver settings are not used, and the application's own default settings are applied.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print].
The [Print] dialog box appears.
B Select the printer you want to use in the [Name] list box, and then click [Properties].
The [Printer Properties] dialog box appears.
C Make any settings you require and click [OK].
D Click [OK] to start printing.
17
Setting Up the Printer Driver and Canceling a Print Job
PostScript - Setting Up for Printing
Windows 95/98/Me - Accessing the Printer Properties
1
There are two methods you can use to open the printer properties dialog box.
Changing the default printer settings
To make default printer settings, first open the printer properties dialog box
from the [Printers] window.
Note
❒ With some applications, the printer driver's settings are not used, and the application's own default settings are applied.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Properties].
The [Printer Properties] dialog box appears.
D Make any settings you require and click [Apply].
E Click [OK].
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• PostScript 3
DRIVERS\PS\WIN9X_ME\(Language)\DISK1
18
PostScript - Setting Up for Printing
Making printer settings from an application
To make the printer settings for a specific application, open the [Printer Properties]
dialog box from that application. The following example describes how to make
settings for the WordPad application that comes with Windows 95/98/Me.
1
Note
❒ The actual procedure you should follow to open the [Printer Properties] dialog
box may differ depending on the application. For more information, see the
documentation that comes with the application you are using.
❒ With some applications, printer driver settings are not used, and the application's own default settings are applied.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print].
The [Print] dialog box appears.
B Select the printer you want to use in the Name list box, and then click [Properties].
The [Printer Properties] dialog box appears.
C Make any settings you require and click [Apply].
D Click [OK] to start printing.
Windows 2000/Windows XP/Server 2003 - Accessing the Printer
Properties
Changing the default printer settings - Printer Properties
Limitation
❒ Changing the setting of the printer requires Manage Printers permission.
Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account
that has Manage Printers permission.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
Note
❒ With Windows XP Professional/Windows Server 2003, access the [Printers
and Faxes] window from [Start] on the taskbar.
❒ With Windows XP Home Edition, open [Control panel] from [Start], click
[Printers and Other Hardware], and then click [Printers and Faxes] on the screen
that appears.
19
Setting Up the Printer Driver and Canceling a Print Job
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Properties].
1
The Printer Properties appear.
On the [File] menu, click [Properties].
The [Printer Properties] dialog box appears.
D Make any settings you require and click [Apply].
Note
❒ Settings you make here are used as the default settings for all applications.
E Click [OK].
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• PostScript 3
DRIVERS\PS\WIN2K_XP(Language)\DISK1
Changing the default printer settings – Printing Preferences Properties
Limitation
❒ Changing the setting of the printer requires Manage Printers permission.
Members of the Administrators and Power Users groups have Manage Printers permission by default. When you set up options, log on using an account
that has Manage Printers permission.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer whose default settings you want to
change.
20
PostScript - Setting Up for Printing
C On the [File] menu, click [Printing Preferences...].
The [Printing Preferences Properties] appears.
D Make any settings you require and click [Apply].
1
Note
❒ Settings you make here are used as the default settings for all applications.
E Click [OK].
Making printer settings from an application
To make the printer settings for a specific application, open the [Print] dialog box
from that application. The following example describes how to make settings for
the WordPad application that comes with Windows 2000/Windows XP/Server
2003.
Note
❒ The actual procedures you should follow to open the [Print] dialog box may
differ depending on the application. For more information, see the documentation that comes with the application you are using.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print...].
The [Print] dialog box appears.
B Select the printer you want to use in the [Select Printer] box.
Click the tab that you want to change its print setting.
Note
❒ With Windows XP/Server 2003, click [Preference] to open the Printer Preference window.
C Make any settings you require and click [Apply].
D Click [OK] to start printing.
21
Setting Up the Printer Driver and Canceling a Print Job
Windows NT 4.0 - Accessing the Printer Properties
Changing the default printer settings - Printer Properties
1
Limitation
❒ Changing the setting of the printer requires Full Control access permission.
Members of Administrators, Server Operators, Print Operators, and Power
Users groups have Full Control permission by default. When you set up options, log on using an account that has Full Control permission.
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears .
B Click to select the icon of the printer whose default settings you want to
change.
C On the [File] menu, click [Properties].
The [Printer Properties] dialog box appears.
D Make any settings you require and click [OK].
Note
❒ Setting you make here are used as the default settings for all applications.
- If a message is displayed during printer driver installation
When there is a driver in the computer that is newer than the one currently being
installed, a message dialog box appears.
If this happens, you cannot install using the Auto Run program. Use the driver
displayed in the message, and reinstall using [Add Printer].
A Click [Start], point to [Settings], and then click [Printers].
B Double-click the [Add Printer] icon.
C Follow the wizard to install the driver.
If the printer driver is stored on a CD-ROM, the source for installation is as
follows: (If the installer starts up, click [Cancel] to quit it.)
• PostScript 3
DRIVERS\PS\NT4\(Language)\DISK1
22
PostScript - Setting Up for Printing
Changing the default printer settings - Default Document Properties
Limitation
❒ Changing the setting of the printer requires Full Control access permission.
Members of the Administrators, Server Operators, Print Operators, and Power Users groups have Full Control permission by default. When you set up
options, log on using an account that has Full Control permission.
1
A Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
B Click to select the icon of the printer you want to use.
C On the [File] menu, click [Document Defaults].
The Default Document Properties appear.
D Make any settings you require and click [OK].
Note
❒ Settings you make here are used as the default settings for all applications.
Making printer settings from an application
To make the printer settings for a specific application, open the [Printer Properties]
dialog box from that application. The following example describes how to make
settings for the WordPad application that comes with Windows NT 4.0.
Note
❒ The actual procedure you should follow to open the [Printer Properties] dialog
box may differ depending on the application. For more information, see the
documentation that comes with the application you are using.
❒ With some applications, printer driver settings are not used, and the application's own default settings are applied.
❒ Any settings you make in the following procedure are valid for the current
application Only.
A On the [File] menu, click [Print].
The [Print] dialog box appears.
B Select the printer you want to use in the [Name] list box, and then click [Properties].
The [Printer Properties] dialog box appears.
C Make any settings you require and click [OK].
D Click [OK] to start printing.
23
Setting Up the Printer Driver and Canceling a Print Job
Macintosh - Setting Up for Printing
Making paper settings from an application
1
A Open the file you want to print.
B On the [File] menu, click [Page Setup].
The [AdobePS Page Setup] dialog box appears.
C Confirm that the printer you want to use is shown in the [Format for:] box.
Note
❒ If the printer is not shown in the [Format for:] box, use the pop-up menu to
display a list of available printers.
Reference
The actual appearance of the Page Setup depends on the application you
are using. See the documentation that comes with the Macintosh for more
information.
D From the [Paper:] *1 box, select the paper size.
*1
Under Mac OS X, this is called [Paper Size].
E Make any settings you require and then click [OK].
Setting up for printing from an application
A Open the file you want to print.
B On the [File] menu, click [Print].
The Printer Settings appears.
C Confirm that the printer is selected in the [Printer :] box.
D Make any settings you require and click [Print] to start printing.
24
Canceling a Print Job
Canceling a Print Job
Windows 95/98/Me, Windows 2000, Windows XP/Server 2003,
Windows NT 4.0 - Canceling a Print Job
1
A Double-click the printer icon on the Windows taskbar.
A window appears, showing all the print jobs that are currently queuing to
be printed. Check the current status of the job you want to cancel.
B Select the name of the job you want to cancel.
C On the [Document] menu, click [Cancel].
Note
❒ You can also open the print job queue window by double-clicking the
printer icon in the [Printer] window.
D Press {Job Reset}} on the control panel.
“Job Reset?” appears on the panel display.
E Select between canceling the job currently printing and canceling all jobs
(including the job currently printing) using {U} or {T}.
• When canceling only the current job
Job Reset?
Current Job
• When canceling all jobs including the current job
Job Reset?
All Jobs
Note
❒ It is also possible to annul the cancellation. Resume printing is resumed by
selecting "Resume Print", and then pressing [Enter].
25
Setting Up the Printer Driver and Canceling a Print Job
F Press {Enter #}}.
On Line
1
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
A confirmation message appears.
Note
❒ Printing resumes if you press [Escape] at this point.
G Press {Enter #}}.
The job is canceled. When the cancellation procedure is complete, the message appears.
Important
❒ When the printer is being shared by multiple computers, be careful not to
accidentally cancel someone else's print job.
Note
❒ A print job that contains a large volume of data may take considerable time
to stop.
Macintosh - Canceling a Print Job
A Double-click the printer's icon on the desktop.
A window appears, showing all the print jobs that are currently queuing to
be printed. Check the current status of the job you want to cancel.
Note
❒ Under Mac OS X, start Print Center.
B Select the name of the job you want to cancel.
C Click the pause icon, and then click the trash icon.
D Press {Job Reset}} on the control panel.
“Job Reset?” appears on the panel display.
26
Canceling a Print Job
E Select between canceling the job currently printing and canceling all jobs
(including the job currently printing) using {U} or {T}.
• When canceling only the current job
1
Job Reset?
Current Job
• When canceling all jobs including the current job
Job Reset?
All Jobs
Note
❒ It is also possible to annul the cancellation. Resume printing is resumed by
selecting "Resume Print", and then pressing [Enter].
F Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
A confirmation message appears.
Note
❒ Printing resumes if you press [Escape] at this point.
G Press {Enter #}}.
The job is canceled. When the cancellation procedure is complete, the message appears.
Important
❒ When the printer is being shared by multiple computers, be careful not to
accidentally cancel someone else's print job.
Note
❒ A print job that contains a large volume of data may take considerable time
to stop.
27
Setting Up the Printer Driver and Canceling a Print Job
1
28
2. Uninstalling the Printer
Driver and Software
Uninstalling the PCL 6/5e Printer Driver
This section describes how to uninstall the printer driver. The actual procedure
may differ depending on the operating system.
Follow one of the appropriate procedures below.
Windows 95/98/Me - Uninstalling the PCL 6/5e Printer Driver
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
E Click [Yes] to uninstall the printer driver.
Windows 2000/Windows XP/Server 2003 - Uninstalling the PCL
6/5e Printer Driver
Limitation
❒ Uninstalling a printer driver requires Manage Printers permission. Members
of the Administrators and Power Users groups have Manage Printers permission by default. When you uninstall a printer driver, log on using an account
that has Manage Printers permission.
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
Note
❒ With Windows XP Professional/Windows Server 2003, access the [Printers
and Faxes] window from [Start] on the taskbar.
❒ With Windows XP Home Edition, open [Control panel] from [Start], click
[Printers and Other Hardware], and then click [Printers and Faxes] on the screen
that appears.
29
Uninstalling the Printer Driver and Software
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
E Click [Yes] to uninstall the printer driver.
Note
❒ Before upgrading the printer driver, restart your computer after uninstalling the old version of the printer driver.
2
Windows NT 4.0 - Uninstalling the PCL 6/5e Printer Driver
Limitation
❒ Uninstalling a printer driver requires Full Control access permission. Members of the Administrators, Server Operators, Print Operators, and Power Users groups have Full Control Permission by default. When you install a
printer driver, log on using an account that has Full Control permission.
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
E Click [Yes] to uninstall the printer driver.
Note
❒ Before upgrading the printer driver, restart your computer after uninstalling the old version of the printer driver.
30
Uninstalling the RPCS Printer Driver
Uninstalling the RPCS Printer Driver
This section describes how to uninstall the printer driver. The actual procedure
may differ depending on the operating system.
Follow one of the appropriate procedures below.
2
Windows 95/98/Me - Uninstalling the RPCS Printer Driver
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
E Click [Yes] to uninstall the printer driver.
Windows 2000/Windows XP/Server 2003 - Uninstalling the RPCS
Printer Driver
Limitation
❒ Uninstalling a printer driver requires Manage Printers permission. Members
of the Administrators and Power Users groups have Manage Printers permission by default. When you uninstall a printer driver, log on using an account
that has Manage Printers permission.
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
Note
❒ With Windows XP Professional/Windows Server 2003, access the [Printers
and Faxes] window from [Start] on the taskbar.
❒ With Windows XP Home Edition, open [Control panel] from [Start], click
[Printers and Other Hardware], and then click [Printers and Faxes] on the screen
that appears.
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
31
Uninstalling the Printer Driver and Software
E Click [Yes] to uninstall the printer driver.
Note
❒ Before upgrading the printer driver, restart your computer after uninstalling the old version of the printer driver.
Windows NT 4.0 - Uninstalling the RPCS Printer Driver
2
Limitation
❒ Uninstalling a printer driver requires Full Control access permission. Members of the Administrators, Server Operators, Print Operators, and Power Users groups have Full Control Permission by default. When you install a
printer driver, log on using an account that has Full Control permission.
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
E Click [Yes] to uninstall the printer driver.
Note
❒ Before upgrading the printer driver, restart your computer after uninstalling the old version of the printer driver.
32
Uninstalling the PostScript Printer Driver
Uninstalling the PostScript Printer Driver
This section describes how to uninstall the PostScript printer driver.
The actual procedure may differ depending on the operating system.
Follow one of the appropriate procedures below.
2
Windows 95/98/Me - Uninstalling the PostScript Printer Driver
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
E Click [Yes] to uninstall the printer driver.
Windows 2000/Windows XP/Server 2003 - Uninstalling the
PostScript Printer Driver
Limitation
❒ Uninstalling a printer driver requires Manage Printers permission. Members
of the Administrators and Power Users groups have Manage Printers permission by default. When you uninstall a printer driver, log on using an account
that has Manage Printers permission.
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
Note
❒ With Windows XP Professional/Windows Server 2003, access the [Printers
and Faxes] window from [Start] on the taskbar.
❒ With Windows XP Home Edition, open [Control panel] from [Start], click
[Printers and Other Hardware], and then click [Printers and Faxes] on the screen
that appears.
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
33
Uninstalling the Printer Driver and Software
E Click [Yes] to uninstall the printer driver.
Note
❒ Before upgrading the printer driver, restart your computer after uninstalling the old version of the printer driver.
Windows NT 4.0 - Uninstalling the PostScript Printer Driver
2
Limitation
❒ Uninstalling a printer driver requires Full Control access permission. Members of the Administrators, Server Operators, Print Operators, and Power Users groups have Full Control Permission by default. When you uninstall a
printer driver, log on using an account that has Full Control permission.
A Close all applications that are currently running.
B Click [Start] on the taskbar, point to [Settings], and then click [Printers].
The [Printers] window appears.
C Click to select the icon of the printer you want to remove.
D On the [File] menu, click [Delete].
A confirmation dialog box appears.
E Click [Yes] to uninstall the printer driver.
Note
❒ Before upgrading the printer driver, restart your computer after uninstalling the old version of the printer driver.
Macintosh - Uninstalling the PostScript Printer Driver
A Drag the “AdobePS” file from the [Extensions] folder in [System Folder] to
[Trash].
B Drag the PPD file and plug-in file from the [Printer Descriptions] folder in the
[Extensions] folder in [System Folder] to [Trash].
34
3. Paper and Other Media
Paper and Other Media Supported by This
Printer
Paper Types and Sizes
This section describes the type, size, feed direction, and maximum amount of paper that can be loaded into each paper tray in this printer.
Important
❒ If you use damp or curled paper, a misfeed might occur. In this case, try turning over the paper stack in the paper tray. If there is no improvement, change
to paper with non curl.
Note
❒ The following symbols and terminology are used to represent the feed direction.
In this manual
K ↑ (Feed direction)
L ↑ (Feed direction)
On the panel display
A4 (210 × 297)
Letter (81/2×11)
A5 (210 × 148)
(81/2 × 51/2)
Paper feed direction
Short-edge feed direction
Long-edge feed direction
❒ It is recommended that you load paper of the size and direction you frequently use in the tray selected with “Tray Priority”. For more information about
Tray Priority, see p.124 “Paper Input Menu”.
❒ When loading paper of the same size in more than one tray, it is recommended that you load paper in the same direction in each tray.
Reference
For more information about loading each type of paper, see p.47 “Loading Paper and Other Media”.
Important
❒ Be sure to set the paper size dial to match the actual paper size loaded in the
tray. When the actual paper size is not shown on the dial, set the dial to “p”
and select the paper size using the control panel.
❒ For Tray 1, 2 and 3, the dial setting overrides the setting made with the control
panel.
❒ The optional Envelope Feeder Unit requires installation of the optional Paper
Feed Unit. Up to two Paper Feed Units can be installed at the same time. The
Envelope Feeder Unit can be used in Tray 2 or Tray 3.
35
Paper and Other Media
Note
❒ The printable paper size depends on the memory size of the printer and print
data, see p.187 “Memory Capacity and Paper Size”.
❒ For more information about the meanings of the abbreviations, see the notes
at the bottom of each table.
Size (mm)
Paper Tray
(Tray1)
Paper Feed
Unit (Tray 2/3)
Envelope
Feeder Unit
A4
K
210 × 297
❍
✩
✩
X
B5 JIS
K
182 × 257
❍
✩
✩
X
A5
K
148 × 210
❍
✩
✩
X
L
210 × 148
❍
★
X
X
K
105 × 148
❍
X
X
X
Legal (LG, 81/2 × 14)
K
216 × 356
❍
✩
✩
X
Letter (LT, 8 /2 × 11)
K
216 × 279
❍
✩
✩
X
51/2 × 81/2
K
140 × 216
❍
✩
✩
X
L
216 × 140
❍
★
X
X
K
184 × 276
❍
X
★
X
Folio (81/4 × 13)
K
210 × 330
❍
★
★
X
Foolscap (F4, 8 /2 × 13)
K
216 × 330
❍
★
★
X
F/GL (8 × 13)
K
203 × 330
❍
★
★
X
Com#10 Env (41/8 × 91/2)
K
104.8 × 241.3
❍
X
X
❍
C5 Env (6.38 × 9.02)
K
162 ×229
❍
X
X
❍
C6 Env (4.49 × 6.38)
K
114 ×162
❍
X
X
❍
K
110 × 220
❍
X
X
❍
Monarch Env (3 /8 × 7 /2)
K
98.4 × 190.5
❍
X
X
❍
Custom Size
—
—
❍*
★**
★**
X
K
195 × 267
❍
★
★
X
3
A6
1
Executive (Exec.,
71/
4
×
101/
1
DL Env (4.33 × 8.66)
7
16K (7.68 × 10 /2)
1
1
2)
Bypass Tray
Feed direction
❖ Input Paper Sizes (Metric version)
• ❍
Means that the size is supported but the paper size should be set with the control panel. There is no dial on the tray.
See p.50 “Loading Paper in the Bypass Tray”
See p.57 “Loading envelopes into the Envelope Feeder Unit”
36
Paper and Other Media Supported by This Printer
• ✩
Means that the size is supported and indicated on the tray dial. Be sure to set
the paper size dial to match the actual paper size loaded in the tray.
• ★
Means that the size is supported but not indicated on the tray dial. You
should set the tray dial to “p”, and select the paper size with the control panel.
• ❍*
Means that the supported size is approximately 90.0 - 216.0 mm in width, and
approximately 139.7 - 432.0 mm in length. The supported size may differ depending on the printer language you use. Use the printer driver to set custom
sizes. Set custom sizes with the control panel.
• ★**
Means that the supported size is approximately 139.7 - 216.0 mm in width,
and approximately 139.7 - 356 mm in length. The supported size may differ
depending on the printer language you use. Use the printer driver to set custom sizes. Set custom sizes with the control panel.
• X
Means that the size is not supported.
3
37
Paper and Other Media
Size (inch)
Paper Tray
(Tray1)
Paper Feed
Unit (Tray 2/3)
Envelope
Feeder Unit
Legal (LG)
K
81/2 × 14
❍
✩
✩
X
Letter (LT)
K
81/2 × 11
❍
✩
✩
X
5 /2 × 8 /2
K
5 /2 × 8 /2
❍
✩
✩
X
L
81/2 × 51/2
❍
★
X
X
Executive (Exec.)
K
71/4 × 101/2
❍
X
★
X
A4
K
8.26 × 5.83
❍
✩
✩
X
B5 JIS
K
7.17 × 10.12
❍
✩
✩
X
A5
K
5.83 × 8.26
❍
✩
✩
X
L
8.26 × 5.83
❍
★
X
X
A6
K
4.13 × 5.63
❍
X
X
X
Folio
K
8 /4 × 13
❍
★
★
X
Foolscap F4
K
81/2 × 13
❍
★
★
X
F/GL
K
8 × 13
❍
★
★
X
Com#10 Env
K
4 /8 × 9 /2
❍
X
X
❍
C5 Env
K
6.38 × 9.02
❍
X
X
❍
C6 Env
K
4.49 × 6.38
❍
X
X
❍
DL Env
K
4.33 × 8.66
❍
X
X
❍
Monarch Env
K
37/8 × 71/2
❍
X
X
❍
Custom Size
—
—
❍*
★**
★**
X
16K
K
7.68 × 101/2
❍
★
★
X
1
1
3
1
Bypass Tray
Feed direction
❖ Input Paper Sizes (Inch version)
1
1
1
1
• ❍
Means that the size is supported but the paper size should be set with the control panel. There is no dial on the tray.
See p.50 “Loading Paper in the Bypass Tray”
See p.57 “Loading envelopes into the Envelope Feeder Unit”
• ✩
Means that the size is supported and indicated on the tray dial. Be sure to set
the paper size dial to match the actual paper size loaded in the tray.
• ★
Means that the size is supported but not indicated on the tray dial. You
should set the tray dial to “p”, and select the paper size with the control panel.
38
Paper and Other Media Supported by This Printer
• ❍*
Means that the supported size is approximately3.55 - 8.50 inches in width,
and approximately 5.50 - 17.00 inches in length. The supported size may differ depending on the printer language you use. Use the printer driver to set
custom sizes. Set custom sizes with the control panel.
• ★**
Means that the supported size is approximately 5.51 - 8.50 inches in width,
and approximately 5.51 - 14.02 inches in length. The supported size may differ depending on the printer language you use. Use the printer driver to set
custom sizes. Set custom sizes with the control panel.
• X
means that the size is not supported.
3
❖ Paper weight and number of sheets to be set
Supported paper weight
Maximum number of
sheets (Plain Paper) *1
Paper Tray
60 - 105 g/m2 (16 - 28 lb.
bond)
500 (80 g/m2, 20 lb. bond)
Paper Feed Unit Type 400 (option)
60 - 105 g/m2 (16 - 28 lb.
bond)
500 (80 g/m2, 20 lb. bond)
Bypass Tray
52 - 162 g/m2 (14 - 43 lb.
bond)
100 (80 g/m2, 20 lb. bond)
Envelope Feeder Type 400 *2
*1
*2
For other kind of papers,
see p.42 “Types of Paper
and Other Media”.
p.42 “Types of Paper and Other Media”.
Confirm that the top of the stack is not higher than the limit mark indicated on the
side fence of the tray.
The Envelope Feeder Unit requires the installation of the optional Paper Feed Unit.
39
Paper and Other Media
Size (mm)
A4
K
210 × 297
❍
❍
B5 JIS
K
182 × 257
❍
❍
A5
K
148 × 210
❍
❍
L
210 × 148
❍
❍
K
105 × 148
❍
X
Legal (LG, 81/2 × 14)
K
216 × 356
❍
❍
× 11)
K
216 × 279
❍
❍
K
140 × 216
❍
❍
L
216 × 140
❍
❍
Executive (Exec., 7 /4 × 10 /2)
K
184 × 276
❍
X
Folio (81/4 × 13)
K
210 × 330
❍
❍
Foolscap (F4, 8 /2 × 13)
K
216 × 330
❍
❍
F/GL (8 × 13)
K
203 × 330
❍
❍
Com#10 Env (41/8 × 91/2)
K
104.8 × 241.3
❍
X
C5 Env (6.38 × 9.02)
K
162 ×229
❍
X
C6 Env (4.49 × 6.38)
K
114 ×162
❍
X
K
110 × 220
❍
X
Monarch Env (3 /8 × 7 /2)
K
98.4 × 190.5
❍
X
Custom Size
—
—
❍
X
K
195 × 267
❍
❍
A6
Letter (LT,
81/
2
51/2 × 81/2
1
1
1
DL Env (4.33 × 8.66)
7
16K (7.68 ×
101/
2)
1
• ❍
Means that the size is supported.
• X
Means that the size is not supported.
40
Duplex Unit
Feed direction
3
Output Tray
(Standard Tray)
❖ Output Paper Sizes (Metric version)
Paper and Other Media Supported by This Printer
Size (inch)
Legal (LG)
K
81/2 × 14
❍
❍
Letter (LT)
K
81/2 × 11
❍
❍
51/2 × 81/2
K
51/2 × 81/2
❍
❍
L
81/2 × 51/2
❍
❍
Executive (Exec.)
K
71/4 × 101/2
❍
X
A4
K
8.26 × 5.83
❍
❍
B5 JIS
K
7.17 × 10.12
❍
❍
A5
K
5.83 × 8.26
❍
❍
L
8.26 × 5.83
❍
❍
A6
K
4.13 × 5.63
❍
X
Folio
K
81/4 × 13
❍
❍
Foolscap F4
K
81/2 × 13
❍
❍
F/GL
K
8 × 13
❍
❍
Com#10 Env
K
41/8 × 91/2
❍
X
C6 Env
K
4.49 × 6.38
❍
X
C5 Env
K
6.38 × 9.02
❍
X
DL Env
K
4.33 × 8.66
❍
X
Monarch Env
K
37/8 × 71/2
❍
X
Custom Size
—
—
❍
X
16K
K
7.68 × 101/2
❍
❍
Duplex Unit
Feed direction
Output Tray (Standard Tray)
❖ Output Paper Sizes (Inch version)
3
• ❍
Means that the size is supported and that the paper size should be set with
the control panel. There is no dial on the tray.
• X
Means that the size is not supported.
41
Paper and Other Media
Paper Recommendations
Note the following suggestions when handling or selecting paper used with this
printer.
Loading Paper
• Confirm the paper types of the printer. For more information, see p.42 “Types
of Paper and Other Media”. Print quality cannot be guaranteed if other paper
types are used.
• Do not use paper that is already printed on.
• If you load paper into the paper tray, be sure not to stack over the limit mark.
• If you load paper onto the Bypass Tray, be sure that paper fits under the side
guide.
• If you load paper into the paper tray, confirm that the print side is facing
down.
• If you load paper onto the Bypass Tray, confirm that the print side is facing
up.
• It is necessary to set the paper size on the control panel when the set paper
size is not shown on the paper size dial.
3
Storing Paper
Paper should always be stored properly. Improperly stored paper might result
in poor print quality, paper misfeeds or printer damage.
Recommendations are as follows:
• Avoid storing paper in humid areas.
• Avoid exposing paper to direct sunlight.
• Store on a flat surface.
• Keep open reams of paper in the package in which the paper came.
Types of Paper and Other Media
❖ Plain Paper
• If you print on paper heavier than 105 g/m2 (28 lb. bond), use the Bypass
Tray. The Bypass Tray can hold paper up to 162 g/m2 (43 lb. bond) in
weight.
• If you load paper heavier than 155 g/m2 (41 lb. bond) onto the Bypass
Tray, set the printer to Thick Paper mode using the control panel.
• If paper is curled or bent, correct it before loading.
42
Paper and Other Media Supported by This Printer
❖ OHP transparencies
• Load Only one OHP Transparency at the same time onto the Bypass Tray.
• When loading an OHP Transparency onto the Bypass Tray, set the printer
to Transparency mode with the control panel.
• Be careful not to touch the print side of the OHP transparencies, otherwise
the print side gets dirty or damaged, and results in poor print quality.
• When printing on an OHP Transparency that has a print side, load it facing
down onto the Bypass Tray.
❖ Adhesive Labels
• Load Only one adhesive label at the same time onto the Bypass Tray.
• Use adhesive Labels in which the whole side can be printed on.
• Do not use adhesive Labels having exposed glue.
• If the print side is coated, print quality might be reduced, as the toner
might not fuse well.
3
❖ Envelopes
• When printing on envelopes, use the Bypass Tray or the Envelope Feeder
Unit.
• Even if the optional Envelope Feeder is not installed, you can select envelope sizes for Tray 2 and Tray 3 using the control panel. However, you cannot load envelopes until the optional Envelop Feeder Unit is installed.
To use the Envelope Feeder Unit, installation of the optional Paper Feed
Unit is required. See “Envelope Feeder Type 400” in the Setup Guide.
• Specifications of envelopes are as follows:
Metric version
Weight
Recommended weight
and size
72 – 90 g/m2
72
g/m2,
(C6 Env)
114 × 162 mm
Inch version
19 – 24 lb. bond
24 lb. bond, 37/8 × 71/2 inches
(Monarch)
• You can load up to 10 envelopes (72 – 90 g/m2, 19 – 24 lb. bond) onto the
Bypass Tray at the same time, without forcibly pressing them. Confirm
that the envelopes are not damp, and that the top of the stack is not higher
than the limit mark on the side guide. See p.55 “Loading envelopes onto
the Bypass Tray”.
• You can load up to 60 envelopes (72 – 90 g/m2, 19 – 24 lb. bond) into optional Envelope Feeder Unit at the same time, without forcibly pressing
them. Confirm that the envelopes are not damp, and that the top of the
stack is not higher than the limit mark on the side guide. See p.57 “Loading
envelopes into the Envelope Feeder Unit”.
• Confirm that the print side is facing up when loading onto the Bypass
Tray, and facing down when loading into the optional Envelope Feeder
Unit.
43
Paper and Other Media
• Load the envelopes with the flaps aligned to the left side fence. The flaps
should be securely folded up.
• Confirm that there is no air in the envelopes before loading.
• To get better print quality, it is recommended that you set the right, left,
top, and bottom print margin, to at least 15 mm (0.6 inches) each.
• Do not print on both sides of envelopes.
• Load Only one size and type of envelopes at the same time.
• Before loading envelopes, flatten the leading edges (the side being fed into
the printer) of them by running a pencil or ruler across them.
• Before loading envelopes, confirm that they are rectangular in shape.
• Do not use the non-supported envelopes listed on p.39 “Paper weight and
number of sheets to be set”.
3
Paper not supported by this printer
Avoid using the following types of paper that are not supported by this printer:
• Paper whose weight is heavier or lighter than the limitation. See p.35 “Paper
Types and Sizes”.
• Bent, folded or creased paper
• Curled or twisted paper
• Torn paper
• Wrinkled paper
• Damp paper
• Paper stuck together
• Paper that is dry enough to emit static electricity
• Paper that has already been printed on, with the exception of Preprinted Letterhead
Note
❒ Ink on paper from an earlier print job, another copier, an inkjet printer or
other device could damage the fusing unit of this printer due to a difference in fusing temperatures.
• Coated paper
• Special Paper like thermal paper, aluminum foil, carbon paper and conductive paper
• Heavily textured paper
• Glued paper
• Label paper on which glue or base paper is exposed
• Paper with clips or stapled
• Paper with tape or ribbons attached
44
Paper and Other Media Supported by This Printer
• Envelopes in the following conditions:
• damp
• excessively curled or twisted
• stuck together
• damaged in any way
• with stamps attached
• with windows, holes, perforations, cutouts or embossing
• with metal clasps, string ties or metal folding bars
• designed to be interlocked
• with nicked edges or bent corners
• with rough, wrinkled or laid finishes
• with any exposed adhesive, when the flap is in the sealed or closed position
3
Printable Area
The following shows the printable area for this printer. Be sure to set the print
margins correctly by the application.
4.2mm(1/6 inches)
4.2mm(1/6 inches)
4.2mm
(1/6 inches)
1
4.2mm
(1/6 inches)
4.2mm(1/6 inches)
A
4.2mm(1/6 inches)
: printable area
Important
❒ The maximum printable length is 432 mm (17 inches) in the paper feed direction.
45
Paper and Other Media
Note
❒ Although the entire surface of the paper can be printed on, depending on the
printer driver and settings, print quality is reduced if all margins are set to 5
mm.
❒ When loading oversized paper into the Bypass Tray, support it by hand so it
feeds in properly. Also, since the paper feeding and the paper printed may
differ, depending on thickness and width, check print results in advance.
3
46
Loading Paper and Other Media
Loading Paper and Other Media
Loading Paper in the Paper
Tray
B While lifting the front side of the
tray, pull it out of the printer.
Load paper in the optional Paper
Feed Unit by following the procedures below.
Reference
Up to 500 sheets of paper can be
loaded in the paper tray. Up to 500
sheets of paper can be loaded in
the Paper Feed Unit. This means a
maximum of 1,600 sheets can be simultaneously loaded when two
additional Paper Feed Units are installed. For more information
about type, size and feed direction
of paper that can be loaded in the
tray, see p.35 “Paper Types and
Sizes”.
3
ZKEY140E
C Load paper into the tray with the
print side down.
When you change the paper size
see p.48 “Changing the paper
size”.
A Pull
out the paper tray until it
stops.
ZKEY130E
Important
❒ Confirm that the top of the stack
is not higher than the limit mark
inside the tray.
❒ Confirm that paper fits under
the rear guide.
ZKDX270J
47
Paper and Other Media
D Lift the front of the tray, and slide
it carefully into the printer until it
stops.
Important
❒ If you want to use the paper size
and feed direction that are not
indicated on the paper size dial,
set the dial to “p”. In this case,
you should set the paper size
using the control panel. See
p.124 “Paper Input Menu”.
B While lifting the front side of the
tray, pull it out of the printer.
3
ZKDY150J
Important
❒ Do not slide the paper tray in
with force. If you do, the front
and side guides might move.
Changing the paper size
ZKEY140E
Important
❒ Confirm that the setting of the paper size dial matches the paper size
and feed direction of the paper in
the tray, otherwise the printer
might be damaged, or printing
problems might occur.
The following explanation uses the
example of "Tray 1" for the paper tray.
A Pull
out the paper tray until it
stops. Adjust the paper size dial
to match the size and feed direction of paper in the paper tray.
C If you load paper larger than A4
1
K or 8 /2 × 11 K, you should extend the tray as follows:
Note
❒ You cannot load paper smaller
than A4 K or 81/2 × 11 K, if the
tray is extended. In this case, return the tray to its standard
length.
A Slide the catches inwards to
unlock the tray.
ZKEY160E
ZKEX280E
48
Loading Paper and Other Media
B Slide the tray until it stops.
E Load paper into the tray with the
print side down.
3
ZKEY170E
C Return the catches to their original positions.
ZKEY130E
Important
❒ Confirm that the top of the stack
is not higher than the limit mark
inside the tray.
❒ Confirm that paper fits under
the rear guide.
F If you extend the tray in Step 3,
ZKEY180E
Important
❒ Confirm that the catches return to their original positions securely. If they are not
locked securely, paper misfeeds might occur.
pull the bottom of the paper tray
cover (A
A) up slowly, and then remove the paper tray cover (B
B), in
the order shown in the illustration.
D Adjust the rear and side guides to
the paper size you want to load.
ZKDX780J
ZKEY610E
Important
❒ To avoid damage, pinch the paper guides when moving them.
49
Paper and Other Media
G While lifting the front side of the
tray, place into the printer. Then
carefully slide it into the printer
until it stops.
B Affix the paper wedge to the front
side of the main unit's paper output tray.
3
ZKEX812E
ZKDY150J
Important
❒ Do not slide the paper tray in
with force. If you do, the front
and side guides might move.
Loading Paper in the Bypass
Tray
Opening and Closing the Bypass Tray
Installing the Paper Wedge
If you use long-size paper regularly,
such as Legal, attach the paper wedge
to the main unit's paper output tray.
Open the Bypass Tray
A Press the mark in the center of the
Bypass Tray.
ZKEX810E
A Take
the seal off the paper
wedge's under side.
ZKEX790E
Open the Bypass Tray.
ZKEX811E
50
ZKEY190E
Loading Paper and Other Media
A Slide
Close the BypassTray
When you have finished using the
Bypass Tray, close it as shown in the
next step.
the side guides outward,
and load paper until it stops with
the print side up.
A Close by pressing the mark in the
center of the Bypass Tray.
3
ZKEY200E
ZKEX800E
Note
❒ If you load A4K or lager, or
81/2 × 11 Kor larger, slide out
the Bypass Tray extension (A)
and then flip it open (B).
Loading paper in the Bypass Tray
Reference
With the Bypass Tray, you can
load up to 100 pages at the same
time. For more information about
the type, size and feed direction of
paper that can be loaded in the
tray, see p.35 “Paper Types and
Sizes”.
Note
❒ If you set custom size paper, you
should set the paper size using the
printer driver. Also, use the control panel to set the custom size setting.
ZKEY210E
B Adjust the side guides to the paper width.
ZKEY220E
51
Paper and Other Media
Important
❒ Confirm that paper fits under
the side guides.
❒ Sheets of A4K or 8 1/2 x 11 K
length or longer must be loaded
one at a time. Support the paper
by hand so it feeds in properly.
Additionally, since paper feeding and image quality may differ depending on paper
thickness and width, check
print results in advance using
paper you intend to print on.
3
Note
❒ 45 kg paper or paper of A4K or
8 1/2 x 11 K or longer may not
feed in properly unless it is cut
at right angles.
C Set the paper size and feed direction using the control panel as follows:
A Press {Menu}
}.
On Line
Job Reset
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears
on the panel display.
Paper Input:
Bypass Size
D Press {Enter #}
}.
Bypass Size:
*A4 (210x297)
E Press {T} or {U} to select the
paper size you want to use.
Menu
Bypass Size:
8 1/2 x 14
Escape
Form Feed
Enter
Power
Error
F Press {Enter #}
} to apply the setting. Wait for a while.
Data In
ZKEP020E
“Menu” appears on the panel
display.
B Press {T} or {U} to “Paper Input” menu.
Menu:
Paper Input
52
C Press {Enter #}
}.
Bypass Size:
*8 1/2 x 14
The screen returns to step C in
a few seconds.
Loading Paper and Other Media
G After the panel display changes, press {On Line}
}.
On Line
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
A Press {Menu}}.
Data In
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
3
ZKEP020E
ZKEP010E
"Ready" appears on the panel
display.
Ready
D Start printing with the computer.
Loading custom sized paper in the
Bypass Tray
Important
❒ The settings of custom sized paper
that take effect are not the settings
made on the control panel but the
settings made in the printer driver.
There is no need to change the settings on the control panel. However, when using a printer driver
other than RPCS, you will need to
change the settings on the control
panel.
❒ Applications that do not allow a
custom paper size to be set cannot
print on custom sized paper.
Note
❒ Prints may blur if you use paper of
A4K or 8 1 / 2 x 11 K length or
longer.
"Menu" appears on the panel display.
B Press {T} or {U} to display "Paper
Input" menu.
Menu:
Paper Input
C Press {Enter #}}.
Paper Input:
Bypass Size
The following message appears on
the panel display.
D Press {T} or {U} to display "Custom Size".
Bypass Size:
Custom Size
E Press {Enter #}}.
The following message appears on
the panel display.
F Press {T} or {U} to display the
length in the feed direction, and
then press {Enter #}
}.
53
Paper and Other Media
Note
❒ Pressing {T} or {U} scrolls the
value in increments of 0.1 inch.
Pressing {T} or {U} scrolls the
value in increments of 1 inch.
Bypass Size:
Horiz. 11.69 "
The screen to enter the size along
the length appears.
3
G Press {T} or {U} to display the
size along the length of the feed
direction, and then press {Enter #}
}.
Note
❒ Pressing {T} or {U} scrolls the
value in increments of 0.1 inch.
Pressing {T} or {U} scrolls the
value in increments of 1 inch.
Setting the Bypass Tray Paper Type
To make sure printing is done correctly, you must specify one of the following for the type of sheets loaded in the
tray:
• Plain Paper, Recycled Paper, Special Paper, Color Paper, Letterhead, Preprinted, Transparencies,
Thick Paper
Important
❒ When you load Thick Paper or
transparencies in the Bypass Tray,
always specify the type of paper.
Duplex printing is not possible on
paper in a tray for which Thick Paper or Transparency has been set.
A Press {Menu}}.
On Line
Custom Size:
Vert.
8.27 "
The screen returns to step D in a
few seconds.
H Press {On Line}}.
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Ready
"Ready" appears on the panel display.
Data In
ZKEP020E
"Menu" appears on the panel display.
B Press {T} or {U} to display "Paper
Input" menu.
Menu:
Paper Input
C Press {Enter #}}.
The following message appears on
the panel display.
54
Loading Paper and Other Media
D Press {T} or {U} to display "Paper
Type".
Paper Input:
Paper Type
E Press {Enter #}}.
The following message appears on
the panel display.
F Press {T} or {U} to display "Bypass Tray", and then press {Enter
#}
}.
Paper Type:
Bypass Tray
The screen to select the paper type
appears.
G Press {T} or {U} to display the
type of paper you have loaded,
and then press {Enter #}
}.
Bypass Size:
Thick Paper
The screen returns to step F in a
few seconds.
H Press {On Line}}.
Ready
"Ready" appears on the panel display.
Loading Envelopes
As there are many kinds of envelopes,
be sure to check if those to be used are
supported by this printer.
Reference
For more information about envelopes, see p.42 “Types of Paper and
Other Media”.
3
Important
❒ Even if the optional Envelope
Feeder is not installed, you can select envelope sizes for Tray 2 and
Tray 3 using the control panel.
However, you cannot load envelopes until the optional Envelop
Feeder Unit is installed.
❒ To install the Envelope Feeder
Unit, the optional Paper Feed Unit
must be installed. See “Envelope
Feeder Type 400” in the Setup
Guide.
Loading envelopes onto the Bypass Tray
Reference
With the Bypass Tray, you can
load up to 10 envelopes at the same
time. For more information about
envelopes, see p.42 “Types of Paper and Other Media”.
To open and close the Bypass Tray,
see p.50 “Opening and Closing the
Bypass Tray”
55
Paper and Other Media
A Load
envelopes until they stop,
with the print side up and the
sides of the flaps on the left as
shown below.
3
A Press {Menu}
}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
ZKEY411E
Important
❒ Confirm that the envelope flaps
are securely folded down, and
that there is no air inside the envelopes.
“Menu” appears on the panel
display.
B Press {U} or {T} to display
“Paper Input” menu.
Menu:
Paper Input
C Press {Enter #}
}.
Note
❒ Confirm that the top of the stack
is not higher than the limit mark
on the side guides.
Job Reset
Escape
❒ Do not push the stack of envelopes with too much force.
Form Feed
Enter
Power
Error
On Line
Menu
B Slide the side guides against the
edge of the envelope stack.
Data In
ZKEP060E
Note
❒ Confirm that the edges of envelopes fit under the side guides.
C Set the envelope size and feed direction using the control panel as
follows:
The following message appears.
Paper Input:
Bypass Size
D Press {Enter #}
}.
E Press {U} or {T} to select the
envelope type you want to use.
Reference
For information about types
of envelopes you can select,
see p.35 “Paper and Other
Media Supported by This
Printer”.
56
Loading Paper and Other Media
F Press {Enter #}
} to apply the settings. Wait for a while.
G After the panel display changes, press {On Line}
}.
On Line
A Slide
the optional Paper Feed
Unit (Tray 2) out until it stops.
Next, lift it slightly, then slide it
out.
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
3
Data In
ZKEP010E
"Ready" appears on the panel
display.
Ready
D Start printing with the computer.
Loading envelopes into the Envelope
Feeder Unit
ZKEP330E
Note
❒ Keep the paper tray with paper
in a cool and dry place.
B Prepare
the
Envelope
Feeder
Unit.
C While pinching the side guides,
slide them outward until they
stop. While pinching the rear
guide, slide it toward the back.
Important
❒ With the optional Envelope Feeder
Unit, you can load up to 60 envelopes at the same time. For more
information about envelopes, see
p.42 “Types of Paper and Other
Media”.
The following explanation uses the
example of installing the Envelope
Feeder Unit in "Tray 2".
ZGDY260E
57
Paper and Other Media
D Push the bottom plate down until
it locks into place.
F While pinching the side guides,
slide them along the edge of the
envelope stack.
3
ZDDP360E
E Load envelopes into the Envelope
Feeder Unit, with the print side
down and the flap on the left as
shown in the illustration.
ZDDP380E
Important
❒ Confirm that the envelope flaps
are securely folded down, and
that there is no air inside the envelopes.
Note
❒ Confirm that the top of the stack
is not higher than the limit mark
on the side guides.
❒ Confirm that the envelopes fit
under the side guides.
❒ Do not push the stack of envelopes with too much force.
58
ZGDY370E
G While
pinching the rear guide,
slide it along the edge of the envelope stack.
ZGDY390E
H Lift the front of the tray, and slide
it carefully into the printer until it
stops.
Important
❒ Do not slide the paper tray in
with force. If you do, the front
and side guides might move.
I Set the envelope size and feed direction using the control panel as
follows:
Loading Paper and Other Media
A Press {Menu}
}.
On Line
E Press {Enter #}
}.
The following message appears
on the panel display.
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Tray Paper Size:
Tray 1 (*)
F Press {U} or {T} to display
“Tray 2”.
Data In
ZKEP020E
“Menu” appears on the panel
display.
B Press {U} or {T} to display
“Paper Input” menu.
C Press {Enter #}
}.
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
3
G Press {Enter #}
}.
H Press {U} or {T} to select the
envelope type you want to use.
Reference
For more information about
types of envelopes you can
select, see p.35 “Paper and
Other Media Supported by
This Printer”.
Menu:
Paper Input
On Line
Tray Paper Size:
Tray 2 (*)
I Press {Enter #}
}. Wait for a
while.
J After the panel display changes, press {On Line}
}.
On Line
Menu
Data In
ZKEP060E
Job Reset
Escape
Form Feed
Enter
Power
Error
The following message appears
on the panel display.
Paper Input
Bypass Size
Data In
ZKEP010E
D Press {U} or {T} to display
“Tray Paper Size”.
Paper Input:
Tray Paper Size
"Ready" message appears on
the control panel.
Ready
J Start printing with the computer.
59
Paper and Other Media
3
60
4. Sample Print/Locked Print
Sample Print
Use this function to print Only the
first set of a multiple-set print jobs.
The remaining sets are saved on the
optional Hard Disk Drive in the printer. The saved job can be printed or
canceled from the printer's control
panel.
Also, files specified for Sample Print
can be printed or deleted using the
Web browser. For details, see Network
Printing Guide.
Important
❒ Turning the printer off deletes any
documents or error logs stored on
the optional hard disk drive.
❒ The files printed or deleted using
the Web browser are not listed in
the Sample Print files displayed
from the control panel.
❒ If Sample Print is executed from
the Web browser when the list of
Sample Print files is displayed
from the control panel, although
they appear on the control panel,
they cannot be printed or deleted
from it.
Note
❒ If the application has a collate option, confirm that it is not selected
before sending a print job. By default, sample print jobs are automatically collated by the printer
driver. If the collate option is selected from the application print
dialog box, more pages than intended may be printed.
❒ You can identify the file you want
to print by the User ID and the
time when the job was stored.
❒ The actual number of pages the
printer can save depends on the
contents of the print images. For
example, the printer can save up to
30 jobs or 1,000 pages. It depends
on the data volume.
❒ If the first set of the sample print
file is not as you expected and you
do not want to print the remaining
sets, delete the sample print file using the control panel. If you print
the remaining sets of the sample
print file, the job in the printer is
deleted automatically.
Limitation
❒ To use this function, the optional
Hard Disk Drive must be installed
on the printer.
Reference
For more information about settings for printer driver, see the
printer driver Help.
61
Sample Print/Locked Print
Printing a Sample Print File
The following procedure describes
how to print a sample print file with
the PCL printer driver. For information about how to print a sample print
file with the PostScript printer driver,
see the PostScript 3 Operating Instructions Supplement included on
the CD-ROM. For more information
about RPCS printer driver, see Help.
A From
an application, select the
menu command to print.
The print dialog box appears.
4
B Open the Printer Properties.
C From the [Job Type:] box on
the
[Setup] tab, select [Sample Print].
D Click the [Details...] button.
E In the [User ID:] box, type a User ID
of up to eight alphanumeric characters.
Note
❒ This is used to identify the user
associated with a job.
❒ The User ID can consist of up to
eight alphanumeric (a-z, A-Z, 09) characters.
F Click [OK].
G After making all desired settings,
click [OK].
H Start
printing from the application's print dialog box.
The sample print job is sent to the
printer and the first set is printed.
62
I Check
the print job to confirm
whether the settings are acceptable.
If the settings are fine, go to step J
to print the rest of the print job.
If not, you can delete the saved job.
See p.63 “Deleting a Sample Print
File”
Limitation
❒ Documents are not stored on
the optional hard disk drive in
the following cases (any documents not stored can be confirmed in the error log):
• A Sample Print or Locked
Print document is the 31st
document sent when a total
of 30 documents have already been stored on the optional hard disk drive.
• The last sent document causes the total number of document pages stored on the
optional hard disk drive to
exceed 1,000.
J On
the printer's control panel,
press {Menu}
}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the panel display.
Sample Print
K Press {T} or {U} to display the
“Sample Print“ menu.
{U} or {T} to enter the
number of sets.
Note
❒ You can enter up to 999 sets.
Menu:
Sample Print
L Press {Enter #}}.
On Line
O Press
Qty: 6(1-999)
Press Enter (#)
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
P Press {Enter #}} to print the file.
The following message appears on
the panel display.
4
Processing...
Data In
ZKEP060E
The following message appears on
the panel display.
Sample Print:
08:56 01234567
M Press {T} or {U} to display the
file you want to print, and then
press {Enter #}
}.
Select Action:
Print File
Note
❒ If you want to cancel the sample
print file, press {Escape}
}.
N Press {Enter #}}.
The following message appears on
the panel display.
Qty: 1(1-999)
Press Enter (#)
Note
❒ If you are not satisfied with the
first printout of the sample print
file and do not want to print the remainder, the job in the printer is
deleted automatically.
Deleting a Sample Print File
If you are not satisfied with the printout, delete the sample print file. Then
revise it and print again until the settings are fine.
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
"Menu" appears on the panel display.
63
Sample Print/Locked Print
B Press {T} or {U} to display the
"Sample Print" menu .
The following message appears on
the panel display.
Menu:
Sample Print
Deleted
C Press {Enter #}}.
On Line
F Press {Enter #}} to delete the file.
G Press {On Line}}.
Menu
On Line
Job Reset
4
Form Feed
Power
Escape
Job Reset
Escape
Form Feed
Enter
Power
Error
Enter
Error
Data In
ZKEP060E
The following message appears on
the panel display.
Sample Print:
08:56 01234567
D Press {T} or {U} to display the
file you want to delete, and then
press {Enter #}
}.
The following message appears on
the panel display.
Select Action:
Delete File
Note
❒ If you want to cancel the deletion of a sample print file, press
{Escape}
}.
E Press {T} or {U} to display "De-
lete File", and then press {Enter #}
}.
08:56 1234567
Delete? Yes=#
64
Menu
Data In
ZKEP010E
"Ready" appears on the panel display.
Ready
Sample Print
E Press {Enter #}}.
Checking the Error Log
When a print job is not saved on the
hard disk, it remains in the error log
and can be checked using the control
panel.
Limitation
❒ You can view Only the latest 20 error logs of all.
A Press {Menu}}.
"Menu" appears on the panel display.
B Press {T} or {U} to display the
The following message appears on
the panel display.
Error File(s):
06:52 ABCD1234
Note
❒ You can check the other error
logs by using {T} or {U}.
F Press {T} or {U} to check "Error
File(s)", and then press {Enter #}
}.
The following message appears on
the panel display.
4
"Sample Print" menu.
Sample Print:
Error File(s)
Menu:
Sample Print
G Press {On Line}}.
C Press {Enter #}}.
On Line
On Line
Menu
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
Data In
ZKEP010E
ZKEP060E
The following message appears on
the panel display.
"Ready" appears on the panel display.
Ready
Sample Print:
08:56 1234567
D Press {T} or {U} to display “Error
File(s)”.
Sample Print:
Error File(s)
65
Sample Print/Locked Print
Locked Print
4
Use this function to maintain privacy
when printing confidential documents. Documents will not be printed
out automatically, unless a password
is entered, using the control panel after sending the print job.
Also, files specified for Locked Print
can be printed or deleted using the
Web browser. For details, see Network
Printing Guide.
❒ The actual number of pages the
printer can save depends on the
contents of the print images. For
example, the printer can save up to
30 jobs or 1,000 pages. It depends
on the data volume.
❒ After the locked print file is printed, the job in the printer is deleted
automatically.
Important
❒ Turning the printer off deletes any
documents or error logs stored on
the optional hard disk drive.
Printing a Locked Print File
❒ The files printed or deleted using
the Web browser are not listed in
the Locked Print files displayed
from the control panel.
❒ If Locked Print is executed from
the Web browser when the list of
Locked Print files is displayed
from the control panel, although
they appear on the control panel,
they cannot be printed or deleted
from it.
Limitation
❒ To use this function, the optional
Hard Disk Drive must be installed
on the printer.
Note
❒ If the application has a collate option, confirm that it is not selected
before sending a print job. By default, locked print jobs are automatically collated by the printer
driver. If the collate option is selected from the application print
dialog box, more pages than intended may be printed.
❒ You can identify the file you want
to print by the User ID and the
time when the job was stored.
66
The following procedure describes
how to print a locked print file with
the PCL printer driver. For information about how to print a locked print
file with the PostScript printer driver,
see the PostScript 3 Operating Instructions Supplement included on
the CD-ROM. For more information
about RPCS printer driver, see Help.
A From
an application, select the
menu command to print.
The print dialog box appears.
B Open the Printer Properties.
C From the [Job Type:] box on
the
[Setup] tab, select [Locked Print].
D Click the [Details:] button.
E In the [User ID:] box, type a User ID
of up to eight alphanumeric characters.
Note
❒ This is used to identify the user
associated with a job.
❒ The User ID can consist of up to
eight alphanumeric (a-z, A-Z, 09) characters.
Locked Print
F In the [Password:] box, type a password of four digits.
J On
the printer's control panel,
press {Menu}
}.
Note
❒ The password must be four digits (0-9).
G Click [OK].
H After making all desired settings,
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
click [OK].
I Start
printing from the application's print dialog box.
The locked print job is sent to the
printer.
Limitation
❒ If Locked Print is executed from
the Web Image Monitor while
the list of Locked Print files is
displayed from the control panel, although they appear on the
control panel, they cannot be
printed or deleted from it.
• A Sample Print or Locked
Print document is the 31st
document sent when a total
of 30 documents have already been stored on the optional hard disk drive.
• The last sent document causes the total number of document pages stored on the
optional hard disk drive to
exceed 1,000.
Data In
ZKEP020E
"Menu" appears on the panel display.
4
K Press
{T} or {U} to display
"Locked Print" menu.
Menu:
Locked Print
L Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on
the panel display.
Locked Print:
08:56 1234567
67
Sample Print/Locked Print
M Press {T} or {U} to display a file
you want to print, and then press
{Enter #}
}.
The following message appears on
the panel display.
Password:
[0---]
N Enter
the password you entered
in step F.
A Press {U} or {T} to enter the
leftmost digit of the password.
4
Password:
[1---]
B Press {Enter #}
}.
The next digit appears.
O Press {T} or {U} to display "Print
File", and then press {Enter #}
}.
Select Action:
Print File
Note
❒ If you want to change the
locked print file, press {Escape}
}.
P Press {Enter #}}.
The following message appears on
the panel display.
08:56 1234567
Press # to Print
Q Press {Enter #}} to print the file.
Processing...
Password:
[*2--]
Note
❒ If you want to change the
locked print file, press {Escape}
}.
C Repeat steps A and B to enter
the remaining digit of the password, and the press {Enter #}
}.
If the password is not correct,
the following message appears
and the panel display returns to
the password menu. Reset or reenter the password.
Deleting the Locked Print File
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
Invalid Password
Try Again
"Menu" appears on the panel display.
B Press {T} or {U} to display the
"Locked Print" menu.
Menu:
Locked Print
68
Locked Print
C Press {Enter #}}.
On Line
C Repeat steps A and B to enter
the remaining password digits,
and then press {Enter #}
}.
If the password is not correct,
the following message appears
and the panel display returns to
the password menu. Reenter
the password.
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
Locked Print:
08:56 1234567
D Press {T} or {U} to display the
file you want delete, and then
press {Enter #}
}.
Password:
[0---]
E Enter the password of the locked
print file.
A Press {U} or {T} to enter the
leftmost digit of the password.
Password:
[1---]
B Press {Enter #}
}.
The next digit appears.
Password:
[*2--]
Invalid Password
Try Again
F Press {T} or {U} to display “Delete File”.
4
Select Action:
Delete File
G Press {Enter #}}.
The following message appears on
the panel display.
08:56 ABCD1234
Press # To Del
Note
❒ If you want to change the
locked print file, press {Escape}
}.
H Press {Enter #}}.
The following message appears on
the panel display.
Deleted
Note
❒ If you want to change the
locked print file, press {Escape}
}.
69
Sample Print/Locked Print
I Press {On Line}}.
On Line
C Press {Enter #}}.
Menu
On Line
Menu
Job Reset
Escape
Job Reset
Escape
Form Feed
Enter
Form Feed
Enter
Power
Error
Power
Error
Data In
Data In
ZKEP010E
"Ready" appears on the panel display.
4
Ready
D Press {T} or {U} to display “Error
File(s)”.
Limitation
❒ You can view Only the latest 20 error logs of all.
A Press {Menu}}.
Job Reset
Escape
Form Feed
Enter
Power
Error
Locked Print:
Error File(s)
E Press {Enter #}}.
The following message appears on
the panel display.
Menu
Error File(s):
06:52 01234567
Data In
ZKEP020E
"Menu" appears on the panel display.
B Press {T} or {U} to display the
"Locked Print" menu.
Menu:
Locked Print
70
The following message appears on
the panel display.
Locked Print:
08:56 01234567
Checking the Error Log
On Line
ZKEP060E
Locked Print
F Press {T} or {U} to check "Error
File(s)", and then press {Escape}
}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP040E
The following message appears on
the panel display.
4
Locked Print:
Error File(s)
Note
❒ Press {Escape}
} to return to the
previous menu.
G Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
"Ready" appears on the panel display.
Ready
71
Sample Print/Locked Print
4
72
5. Troubleshooting
Error & Status Messages on the Control
Panel
Messages/Second messages
Call Service: EC
Power Off On
Description
An error has occurred in the
printer.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
The paper type and size setting on the tray differs from
the setting on the driver.
Load { paper size and type }
paper with the selected feed
direction into tray. Printing
will not automatically resume
if the paper type, size and direction setting is incorrect.
Make sure that the paper size,
feed directions and paper type
set in^p the printer driver and
on the control panel are the
same. There are two methods
to resume printing.
/If Error Reoccur
Call Service
Change Setting
Tray #
/Paper Size:
Solution
Paper type:
A Use the control panel to set
the correct paper type, size
and direction of the paper
in tray.
B Press {Form Feed}
} and se-
lect the tray with the control panel.
You can make to setting to
print disregarding the error
message.
Reference
See “Ppr.Size Errors” in
p.135 “Maintenance Menu
Parameters”.
Cannot check
Signal in Ad hoc
The signal strength for the
wireless LAN cannot be
checked because "802.11 Ad
hoc" or "Ad hoc" is selected in
Comm. Mode for IEEE
802.11b on the Host Interface
menu. The signal strength for
wireless LAN cannot be
checked because "Ad hoc" is
selected in "Comm. Mode" for
"IEEE 802.11b" in the Host Interface menu.
Signal strength cannot be
checked with "802.11b Ad
hoc" or "Ad hoc".
Change the Transmission
mode to [Infrastructure] in the
Host Interface settings.
73
Troubleshooting
Messages/Second messages
Description
Solution
Unit Cover
The cover of the optional Duplex Unit is open.
Close the cover of the optional
Duplex Unit.
Close
The front cover is open.
Close the front cover.
The paper exit cover or the
rear cover is open.
Close the paper exit cover or
the rear cover.
Collate Cancelled
The Collate feature has been
cancelled.
Increase the RAM Capacity.
DHCP assigned Cannot
change
The following address have
Disable the default DHCP setalready been assigned by DH- ting in Network in order to enCP: IP Address, Gateway Ad- ter the addresses manually.
dress, Subnet Mask.
Driver Setting Error (Memory)
The printer identified a down- Verify that the proper memoload error. This error may oc- ry size is specified via the
driver setting.
cur when the installed
memory amount is less than
the driver setting.
Duplex Cancelled
Duplex printing specifications Install additional memory
canceled due to insufficient
units or reduce the amount of
memory or selection of a padata sent.
per size not compatible with
duplex printing.
Energy Save Mode
The printer is in Energy Saver
mode.
Wait for a while.
Error: Enter 10 or 26 Characters
WEP Key setting error, the
number of alphanumerical
numbers should be either 10
or 26.
Enter the correct value.
Exceeded Max. Pages (Collate)
The printer identified a collation table overflow error.
Install additional memory
units or reduce the amount of
data sent.
Exceeded Max. Stored Pages
The maximum number of
Reduce the number of pages
pages has been exceeded dur- to print.
ing Sample Print or Locked
Print.
Exceeded Max. Stored Files
The maximum number of
stored files has been exceeded
during Sample Print or
Locked Print.
Delete the stored files.
Hardware Problem
An error has occurred in the
printer.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Close Duplex
Front Cover
Close Rear/Paper
Exit Cover
5
DIMM
74
Error & Status Messages on the Control Panel
Messages/Second messages
Hardware Problem
Ethernet
Description
An error has occurred in the
optional Network Interface
Board.
Solution
First, turn off the power
switch and then on. If the message appears again, call your
sales or service representative.
Turn off the power switch .
Replace the Network Interface
Board and turn on the power
switch. See “Network Interface
Board Type 2610” in the Setup
Guide.
Turn off the power switch, remove the Network Interface
Board and turn on the power
switch.
Note
❒ If you remove the Network Interface Board, you
cannot print over the network. You can send a print
jobs to the printer Only via
a parallel cable connection.
Hardware Problem
HDD
An error has occurred in the
optional Hard Disk Drive.
5
First, turn the power switch
off and then on, If the message
appears again, call your sales
or service representative.
Turn off the power switch. Replace the Hard Disk Drive and
turn on the power switch. See
“Hard Disk Drive Type 2600” in
the Setup Guide.
Turn off the power switch. Remove the Hard Disk Drive
and turn on the power switch.
Note
❒ If the Hard Disk Drive is
not installed, you cannot
send the sample print job,
locked print job and
download the font to Hard
Disk Drive using the PS
Utility for Mac.
75
Troubleshooting
Messages/Second messages
Hardware Problem
IEEE1394
Description
An error has occurred in the
optional 1394 Interface Unit.
Solution
First, turn the power switch
off and then on, If the message
appears again, call your sales
or service representative.
Turn off the power switch. Replace the 1394 Interface Unit
and turn on the power switch.
See “1394 Interface Unit Type
4510” in the Setup Guide.
Turn off the power switch, remove the 1394 Interface Unit
and turn on the power switch.
Note
❒ If you remove the 1394 Interface Unit, you cannot
send print jobs via the 1394
Interface Unit. You can
Only send print jobs to the
printer via the parallel cable connection.
5
Hardware Problem
IEEE 802.11b
Hardware Problem
NV-RAM
76
An error has occurred in the
optional 802.11b Interface
Unit.
Replace the IEEE 802.11b
board.
An error has occurred in the
printer.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Error & Status Messages on the Control Panel
Messages/Second messages
Hardware Problem
Option RAM
Description
An error has occurred in the
optional Memory Unit.
Solution
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Turn off the power switch, Replace the Memory Unit, and
then turn on the power
switch. See "Memory Unit Type
C (SDRAM Module)" in the
Setup Guide.
Turn off the power switch, remove the Memory Unit, and
then turn on the power
switch.
Note
❒ If you remove the Memory
Unit, you must set up the
option with the printer
driver. If you are using
Windows 95/98/Me, Windows 2000/Windows
XP/Server 2003 and Windows NT 4.0, see "Installing the Printer Driver and
Software" in the Setup
Guide.
5
❒ In this case, you might not
be able to print complex
print jobs.
Hardware Problem
Parallel I/F
Hardware Problem
USB
Hardware Problem
Wireless Board
An error has occurred in the
parallel I/F.
If you use the parallel I/F, replace the interface cable that
caused the error. If the message appears again, contact
your sales or service representative.
There is a problem related to
the Universal Serial Bus Connection and Hardware.
First, turn the power switch
off and then on, If the message
appears again, call your sales
or service representative.
An error has occurred in the
802.11b Interface Unit.
Reset the 802.11b Interface
Unit if the same message appears after turning the power
off and then back on again. If
the same message still appears, contact your sales or
service representative.
77
Troubleshooting
Messages/Second messages
Hardware Problem
Description
Solution
An error has occurred in the
802.11b Interface Unit.
Reset the 802.11b Interface
Unit if the same message appears after turning the power
off and then back on again. If
the same message still appears, contact your sales or
service representative.
HDD Full
The maximum HDD area size
for form/font has been exceeded.
Delete the disused form/font
types.
HDD Full
The optional Hard Disk Drive
is full. The sample print job or
locked print job to be sent
from the computer is too large
to store.
Delete any unnecessary stored
files.
HDD Not Installed
You cannot print the sample
print and the locked print
jobs, because the optional
Hard Disk Drive is not installed.
Install the Hard Disk Drive.
See “Hard Disk Drive Type
2600” in the Setup Guide.
Hex Dump Mode
The printer is in Hex Dump
Mode.
Wait for a while. If the "Hex
Dump Mode" message does
not change, on the panel display press {On Line}
} to return
to the "Ready" condition.
I/O Buffer Overflow
There is too much data for the
I/O Buffer to handle.
Make sure the interface cable
is inserted into the printer and
your computer securely.
Wireless Card
5
Make sure the interface cable
is not damaged or broken.
Increase the size of the I/O
buffer.
Invalid Password
Try Again
The password was not entered correctly.
Wait for two seconds until the
previous display appears.
Then enter the password correctly.
Invalid Password File Protect- An incorrect password has
The file is now protected until
ed
been entered more that 10
an administrator can unlock
times, the file is now protected it.
until an administrator can unlock it.
78
Error & Status Messages on the Control Panel
Messages/Second messages
Load Correct
Size Paper
/Press #
Description
Solution
The paper size setting on the
tray differs from that of actual
paper size in the tray.
Load { paper size } paper of
the selected feed direction and
paper size into the tray. Printing will not automatically resume if the paper size and
direction setting is incorrect.
Make sure that the paper feed
directions set in the printer
driver and on the control panel are the same. There are two
methods to resume printing.
to Continue
A Use the control panel to set
the correct paper size and
direction of the paper in
tray. Then press {Enter #}
}.
B Press {Form Feed}
} and se-
lect the tray with the control panel.
Load Paper /Max. Size Over
/(Paper type)
Reset the job or print on the
This message will appear as
an alternating message in con- availlable paper as is.
junction with [Load Paper],
(A4 Recycle), when a size selected at the driver (PC) side is
larger than the maximum
available size setting on the
machine side, this message
will be displayed.
Load Paper
The paper type and size settings for this tray do not
match the size and type of paper actually loaded.
Load paper into the tray indicated, then press {Enter #}
} to
resume printing. Or press
{Form Feed}
} and select the tray
that holds a different type of
paper. To cancel printing,
press {Job Reset}
}. Then press
{Enter #}
}.
There is no paper left in this
tray.
Load paper into the tray indicated.
The menu is protected and the
settings cannot be changed.
Wait for two seconds until the
previous display appears.
There are no files available for
the sample print job or the
locked print job.
Wait for two seconds until the
previous display appears.
/Paper Size:
Paper type:
Load Paper Tray #
/Paper Size:
5
Paper type:
Menu Protected
Cannot Change
No Files Exist
79
Troubleshooting
Messages/Second messages
Description
No Log Exists
The user has selected to print
the error log in the List/Test
Print mode, however no errors have been detected and
so a log has not been created.
Offline
The printer is offline.
If you want to bring the printer online. Press {On Line}
}.
P=XX I= XXXXXXXX
A controller error. The SC
number indicates the problem.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
A paper setting for the selected tray is not supported for
Duplex printing.
Change the paper setting with
the control panel. Or press
{Form Feed}
} several times until a tray with supported paper settings appears on the
panel display.
Power Off On
/If Error Reoccur
Call Service
Paper Invalid
for Duplex:Tray #
/Change Setting
or Form Feed
5
Solution
#: tray number
Or press {Job Reset}
} to cancel
the print job.
Please wait...
WEP settings are being
changed and updated in this
status message. The printer
device keys are unoperational
during this period.
The user is urged to wait
while emulation is switching.
Print Overrun
A Print overrun occurred on a
file being printed. Only a part
of the data on the page will be
printed, and the print job is
suspended, or the current
print job has been canceled.
To print the image correctly,
add memory to the printer or
reduce the Resolution of the
image.
Printing...
———
Wait for a while.
Processing...
The printer is processing internally.
Wait for a while.
Ready
The printer is online and
ready to make prints.
If you want to take the printer
offline, press {On Line}
}.
Remove Misfeed
There is misfeed in the Duplex
Unit.
Remove the misfed paper.
Duplex Unit
/Open Duplex
Unit Cover
80
Error & Status Messages on the Control Panel
Messages/Second messages
Remove Misfeed
Internal Path
/Open
Description
Solution
There is a misfeed in the print- Remove the misfed paper. See
er.
p.97 “Removing Misfed Paper”.
Front Cover
Remove Misfeed
Paper Exit Cover
There is a misfeed in the paper
exit cover.
Remove the misfed paper.
/Open Paper
Exit Cover
Remove Misfeed
Paper Tray
/Remove Misfeed
There is a misfeed in the print- Remove the misfed paper. See
er.
p.97 “Removing Misfed Paper”.
Paper Tray
Remove Paper
The standard tray is full, and
the print job is suspended.
Remove paper from the standard tray, and the print job
will be resumed automatically.
It is time to replace parts included in the Maintenance
Kit.
Replace parts. See p.175
“MAINTENANCE KIT Type
400”.
The toner cartridge is not set
correctly or toner is almost
run out.
Set the toner cartridge correctly. See p.107 “Replacing the
Toner Cartridge”.
The toner dust is full.
Prepare a new toner cartridge.
If the Image Density gets too
light, replace the toner cartridge with a new one. See
p.107 “Replacing the Toner
Cartridge”.
The fusing unit is not set correctly.
Set the fusing unit correctly,
or set the proper fusing unit.
The toner cartridge is not set
correctly.
Set the toner cartridge correctly. See p.107 “Replacing the
Toner Cartridge”.
The toner cartridge is not set
installed.
If the cartridge is installed,
close the front cover and turn
the off power switch and then
on. If the message appears
again, contact your sales or
service representative.
Correctly
The input paper tray is not set
correctly.
Set the input paper tray correctly.
Resetting Job...
The print job is being reset.
Wait for a while.
Standard Tray
Replace
Maintenance Kit
Replace
Toner Cartridge
Reset Fusing
Unit Correctly
Reset Toner
Cartridge
Reset Tray #
5
81
Troubleshooting
Messages/Second messages
5
Description
RPCS Graphic Error
The graphics is not initialized Replace the installed memory.
because the graphics memory
was not reserved.This error
rarely occurs unless the printer detects the memory failure.
Please note that
“RPCS”(RICOH printer language) is the same worldwide
and does not need to be translated.
RPCS Syntax Error
The printer identified a syntax
error. This error results from;
data transmogrification
caused by the transmission
path problem, data interruption, data transmission from
other drivers, etc.
RPCS Memory Overflow
The printer memory is not ini- Replace the installed memory.
tialized because the CDC
memory was not reserved via
the system call. This error
rarely occurs.
SC XXX-X
An error has occurred.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
SC2001
An error has occurred in the
resident font RAM.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Toner is Almost
The toner is almost run out.
Prepare a new toner cartridge.
If the Image Density gets too
light, replace the toner cartridge with a new one. See
p.107 “Replacing the Toner
Cartridge”.
Waiting...
The printer is waiting for the
next print job.
Wait for a while.
Warming Up...
The printer is warming up or
toner is being supplied.
Wait until the panel display
change the "Ready".
/Power Off On
If Error Reoccur
Call Service
Empty
82
Solution
Be sure to use the correct driver.
Error & Status Messages on the Control Panel
Getting Printer Information over the Network
Printer current status
You can check the printer's status using the telnet command.
❖ telnet
Use the status command.
❖ UNIX
Use the lpq or lpstat command or stat parameter of rsh, rcp, or ftp.
Reference
For more information, see “Remote Maintenance by Telnet (mshell)” in the
Network Printing Guide is provided on the CD-ROM labeled “Operating
Instructions”.
Messages
Description
Call Service Center
There is a malfunction in the
printer.
Turn the printer off and on.
Cover Open: Duplex Unit
The cover of the optional Duplex Unit is open.
Close the cover of the optional
Duplex Unit.
Cover Open: Front Cover
Close the front cover.
Close the front cover.
Cover Open: Paper Exit/Rear
The paper exit cover or the
rear cover is open.
Close the paper exit cover or
the rear cover.
Empty: Toner
The toner cartridge is empty.
Replace the new toner cartridge.
Energy Saver Mode
The printer is in Energy Save
Mode.
Wait for a while.
Error: HDD Board
An error has occurred in the
optional Hard Disk Drive.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Error: IEEE 1394 Board
An error has occurred in the
optional 1394 Interface Unit.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Error: Memory Switch
An error has occurred in
printer.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Error: Optional RAM
An error has occurred in the
optional Memory Unit.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Energy Saver Mode 1
5
Comments
83
Troubleshooting
Messages
Description
Error: Parallel I/F Board
An error has occurred in the
parallel interface board.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Error: USB I/F
An error has occurred in the
USB interface.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
IEEE 802.11b Card Error
The optional IEEE 802.11b
board or the optional IEEE
802.11b card is not installed.
Install the optional IEEE
802.11b board or the optional
IEEE 802.11b card.
IEEE 802.11b Card or Board
Error
An error has occurred in the
optional IEEE 802.11b board
or the optional IEEE 802.11b
card
First, turn the power switch
off and then on. If the message
appears again, set the optional
IEEE 802.11b board. If the
message still appears, call
your sales or service representative.
Low: Toner
The toner cartridge is not set
correctly or toner is almost
running out.
Set the toner cartridge correctly.
Mismatch: Paper Size
The paper size setting of the
tray differs from that of actual
paper size in the tray.
Load paper of the indicated
paper size into the paper tray
being used. See p.35 “Paper
and Other Media Supported
by This Printer”.
Mismatch: Paper Size and
Type
The paper type setting of the
tray differs from that of actual
paper type in the tray.
Load paper of the indicated
paper size and type into the
paper tray being used. See
p.35 “Paper and Other Media
Supported by This Printer”.
Mismatch: Paper Type
The paper type setting of the
tray differs from that of actual
paper type in the tray.
Load paper of the indicated
paper type into the paper tray
being used. See p.35 “Paper
and Other Media Supported
by This Printer”.
No Paper: Input Tray(s)
There is no paper of the indicated paper size in the paper
tray.
Load paper into the paper
tray. See p.47 “Loading Paper
in the Paper Tray”.
Not Detected: Fusing Unit
The fusing unit is not set correctly.
Set the fusing unit correctly. If
the message appears again,
call your sales or service representative.
Not Detected: Input Tray(s)
The input tray is not set correctly.
Set the input tray correctly. If
the message appears again,
call your sales or service representative.
5
84
Comments
Error & Status Messages on the Control Panel
Messages
Description
Comments
Not Detected: Toner Cartridge
The toner cartridge is not set
correctly.
Set the toner cartridge correctly. If the message appears
again, call your sales or service representative.
NVRAM Error
An error has occurred in the
printer.
First, turn the power switch
off and then on. If the message
appears again, call your sales
or service representative.
Paper Misfeed: Duplex Unit
There is misfeed in the Duplex
Unit.
Remove the misfed paper. See
p.104 “When "Remove Misfeed Duplex Unit" Appears”.
Paper Misfeed: Front Cover
There is misfeed in the printer. Remove the misfed paper. See
p.98 “When "Remove Misfeed
Internal Path/Open Front
Cover" Appears”.
Paper Misfeed: Input Tray
There is misfeed in the printer. Remove the misfed paper. See
p.97 “When “Remove Misfeed
Paper Tray” Appears”.
Paper Misfeed: Output Tray
There is misfeed in Output
Tray.
Remove the misfed paper. See
p.99 “When "Remove Misfeed
Paper Exit Cover" Appears”.
Ready
The printer is on line and
ready to make prints.
———
Remove Paper Standard Tray
The Output Tray is full.
Remove paper from Output
Trays.
Replace Maintenance Kit
It is time to replace parts included in the Maintenance
Kit.
Replace parts. See p.175
“MAINTENANCE KIT Type
400”.
Size Media Mismatch
The paper size setting of the
tray differs from that of actual
paper type in the tray.
Load paper of the indicated
paper size and type into the
paper tray being used. See
p.35 “Paper and Other Media
Supported by This Printer”.
Size Mismatch
The paper size setting of the
tray differs from that of actual
paper type in the tray.
Load paper of the indicated
paper size and type into the
paper tray being used. See
p.35 “Paper and Other Media
Supported by This Printer”.
Warming Up/Adjusting...
The printer is warming up or
toner is being supplied.
Wait until the panel display
change the "Ready".
5
85
Troubleshooting
Printer configuration
You can check the printer configuration using telnet.
❖ telnet
Use the info command.
❖ UNIX
Use the info parameter of rsh, rcp, or ftp.
Reference
For more information, see “Remote Maintenance by Telnet (mshell)” in the
Network Printing Guide is provided on the CD-ROM labeled “Operating
Instructions”.
Note
❒ “*” (asterisk) is displayed with the current setting.
❒ Regarding *1–*6, see below table.
5
Item
Description
Printer System
Version of the printer
Network Board
Version of the network board
Input Tray
No. ID number of the paper tray
Name Name of the paper tray*1
PaperSize Paper size loaded in the paper tray*2
Status Current status of the paper tray*3
Output Tray
No. ID number of the Output Tray
Name Name of the Output Tray*4
Status Current status of the Output Tray*5
Emulation
No. ID number of the emulation used by the printName er
Version Name of the emulation used in the printer
Version of the emulation
Program
No. ID number of the program
Name Name of the program
86
Error & Status Messages on the Control Panel
❖ *1 Input Tray: Name
Name
Description
Tray X
Name of installed paper tray. (X is the number
of tray.)
Bypass Tray
Bypass Tray
❖ *2 Input Tray: Paper Size
Paper Size
Description
A4 (210 × 297 mm)
A4K
B5JIS (182 × 257 mm)
B5K
A5 (210 × 148 mm)
A5L
A5 (148 × 210 mm)
A5K
A6 (105 × 148 mm)
A6K
81/2 × 14”
LG/216 × 356K
81/2 × 11”
LT/216 × 279K
51/2 × 81/2”
140 × 216K
custom (210 x 297 mm)
Custom Size
71/4 × 101/2”
71/4 × 101/2K
81/4 × 13”
81/4 × 13K
81/2 × 13”
81/2 × 13K
41/8 × 91/2”
41/8 × 91/2K
37/8 × 71/2”
37/8 × 71/2K
110 × 220 mm
41/3 × 83/4K
C5 Env(162 × 229 mm)
C5 EnvK
8 × 13”
203 × 330K
C6 Env(114 × 162 mm)
C6 EnvK
16K (195 × 267 mm)
16KK
NCS
There is no tray.
**
The paper size is not selected.
5
❖ *3 Input Tray: Status
Status
Description
Normal

NoTray
There is no paper tray
PaperEnd
There is no paper in the paper tray
87
Troubleshooting
❖ *4 Output Tray: Name
Name
Standard Tray
Description
Output Tray
❖ *5 Output Tray: Status
Status
5
88
Description
Normal
----
PaperExist
There is paper in the output tray
OverFlow
Output Tray is full of paper
Error
Other error
Printer Does Not Print
Printer Does Not Print
Possible Cause
Is the power on?
Solutions
Confirm that the cable is securely plugged into the power outlet
and the printer.
Turn on the power switch.
Does the On Line indicator stay on?
Press {On Line}
} so the indicator lights.
Does the Error indicator
stay red?
Check the error message on the panel display and take the required action.
Is paper loaded?
Load paper into the paper tray or on the Bypass Tray.
See p.47 “Loading Paper and Other Media”.
Can you print a configura- If you cannot print a test page, it probably indicates a printer maltion page?
function. You should contact your sales or service representative.
See p.128 “List/Test Print Menu”.
5
If you can print a test page but cannot get the printer to print when
you issue a print command from the computer, it probably means
there is a problem with the computer.
Note that large or complex data might take a long time to be printed.
Is the interface cable connecting the printer to the
computer connected securely?
Connect the interface cable properly. If there are any connectors or
screws, confirm that they are fastened securely.
Are you using the correct
interface cable?
The type of interface cable you should use depends on the computer. Be sure to use the correct one.
If the cable is damaged or worn, replace it with a new one.
Is the paper feed roller
clean?
Clean the paper feed roller if it is dirty. See p.111 “Cleaning the Paper Feed Roller”.
89
Troubleshooting
Possible Cause
Is the Data In indicator
blinking or lit after starting
the print job?
Solutions
If not blinking or lit, the data is not being sent to the printer.
❖ If the printer is connected to the computer using the interface cable
Make sure the following printer port settings are correct:
• For a parallel port connection, port LPT1 or LPT2 should be
set.
• For a USB port connection, port USB00 (n) *1 should be set.
• For a IEEE 1394 (SCSI print) port connection, port
1394_00(n) *1 should be set.
*1
(n) is the number of printers connected.
• Windows 95/98/Me
A Click [Start], point to [Settings] and then click [Printers].
B Click to select the icon of the printer. Next, on the [File]
menu, click [Properties].
C Click the [Details] tab.
5
D Check the [Print to the following port] box to confirm that
the correct port is selected.
• Windows 2000
A Click [Start], point to [Settings] and then click [Printers].
B Click to select the icon of the printer. Next, on the [File]
menu, click [Properties].
C Click the [Port] tab.
D Check the [Print to the following port] box to confirm that
the correct port is selected.
• Windows XP/Server 2003
A With Windows XP Professional/Windows Server 2003,
access the [Printers and Faxes] window from [Start] on the
taskbar.
Note
❒ With Windows XP Home Edition, open [Control panel] from [Start], click [Printers and Other Hardware], and
then click [Printers and Faxes] on the screen that appears.
B Click to select the icon of the printer. Next, on the [File]
menu, click [Properties].
C Click the [Port] tab.
D Check the [Print to the following port(s).] box to confirm
that the correct port is selected.
• Windows NT 4.0
A Click [Start], point to [Settings] and then click [Printers].
B Click to select the icon of the printer. Next, on the [File]
menu, click [Properties].
C Click the [Port] tab.
D Check the [Print to the following port] box to confirm that
90
the correct port is selected.
Printer Does Not Print
Possible Cause
Solutions
Is the Data In indicator
blinking or lit after starting
the print job?
❖ Network Connection
Do you print via a network?
Confirm that the "Ethernet " setting is correct from the control panel. See p.154 “Host Interface Menu”.
Contact your network administrator.
The setting governs the data transfer speed used by the Network
Interface Board. Three options are available:
• Auto (default)
• 100 Mbps
• 10 Mbps
Note
❒ For more information about the appropriate setting to use on
your network, contact your network administrator.
If you use IEEE 1394, check
for the followings.
A Make sure the 1394 Interface Unit is installed properly.
B Make sure the IEEE 1394 cable is connected properly.
5
C Restart the computer.
If the problem still exists when SCSI print is used with Windows 2000 and Windows XP/Server 2003, go to step D.
D Disconnect all the IEEE 1394 cables from the computer.
E If you uninstall the printer driver when the printer is connect-
ed to a computer with "SCSI print", the printer driver may not
be uninstalled properly. To uninstall the driver properly, use
the IEEE 1394 Printer Removal Utility on the CD-ROM that
comes with the printer.
Stored in: CD-ROM labeled "Operating Instructions"DRIVERSUTILITY1394
Note
❒ For more information about the IEEE 1394 Printer Removal
Utility, see the README file in the same folder as the program.
F Restart the computer.
How is the signal strength
when using the wireless
LAN?
❖ Ad Hoc Mode or 802.11 Ad Hoc Mode
Either move to a location where the signal is good, or remove
obstructions.
❖ Infrastructure Mode
Check the signal status from the "Maintenance" menu on the
control panel. See p.141 “Displaying the Signal Strength”. If the
signal is poor, either move to a location where it is good, or remove obstructions.
91
Troubleshooting
Possible Cause
How is the signal strength
when using BluetoothTM?
Solutions
Try the following:
• Check the Wireless Interface Unit and Bluetooth module are
installed properly.
• Check there are no obstructions between computer and printer.
• Change the location of the computer.
• Change the location of the printer.
PDF Direct Print is not executed (PDF file is not
printed).
You must install an optional hard disk drive or set the value of the
[RAM Disk] in the [System Menu] to 2 MB or higher.
Reference
See "Hard Disk Drive Type 2600", Setup Guide for optional hard
disk drive installation.
When printing a PDF with a password set, set the password of the
PDF file using the [PDF: Change PW] menu in [PDF Menu] or Web Image Monitor.
5
Reference
For [PDF: Change PW], see the p.169 “PDF Menu”.
For Web Image Monitor, see Help.
Due to the security setting of the PDF file, when [Printing] under
[Do not Allow] of a PDF file is checked, the file cannot be printed.
Perform printing after unchecking the [Printing] of [Do not Allow].
As a result of printing using PDF Direct Printing,
characters are missing or
misshapen.
Before printing, embed the font in the PDF file to be printed.
Note
❒ If you cannot solve the problem by taking the preceding actions, contact your
sales or service representative.
92
Other Printing Problems
Other Printing Problems
Status
The print side of the page is a
hazy gray.
Possible Causes, Descriptions, and Solutions
Adjust the Image Density.
See p.119 “Making Printer Settings with the Control Panel”.
If paper is curled, correct it.
If you continuously print data that contains extremely small
amount of words or images in the printable area, the printed
side of the page could be a hazy gray. Adjust the Image Density. See p.119 “Making Printer Settings with the Control
Panel”.
Shaking the toner cartridge after pulling out the toner seal
can cause dirt on paper surfaces, toner spillage, or printer
failure. If you have accidentally shaken the toner cartridge,
print some pages (about 50 pages) until the dirt disappear.
5
The paper's reverse side is dirty. Paper loaded in the Paper Tray or Paper Feed Unit may not
match the paper size dial setting. Set the paper size dial so it
matches the size and feed direction of the paper in the tray.
See p.47 “Loading Paper in the Paper Tray”.
The size and feed direction of paper in the Bypass Tray may
not match the control panel settings. Check the control panel
settings so they match the size and feed direction of the paper in the tray.
See p.50 “Loading Paper in the Bypass Tray”.
The next sheet of paper printed may have a dirtied reverse
side if the data size is larger than the paper being printed onto, such as A4 data onto B5 paper.
Image quality varies when
printing on Thick Paper or on
OHP transparencies.
Switch to Thick Paper mode.
• When toner is not fused enough, set it to “On”.
• When the image is blurred, set it to “----”.
See p.119 “Making Printer Settings with the Control Panel”.
Some parts of the print image
are not clear.
Make the Image Density darker.
See p.119 “Making Printer Settings with the Control Panel”.
If Toner Saving mode is selected using the control panel, the
whole image gets lighter.
The print image is not clear.
Due to a sudden change in temperature, condensation might
appear inside the printer, reducing print quality. If this occurs, when you move the printer from a cold room to a
warmer room, do not use the printer until it acclimatizes to
the temperature.
93
Troubleshooting
Status
Possible Causes, Descriptions, and Solutions
Nothing is printed on the paper. Check if the tape of the toner cartridge is completely removed. Be sure to remove the tape completely when replacing the toner cartridge. See p.107 “Replacing the Toner
Cartridge”.
Note
❒ If the power switch is turned on with the tape still attached to the toner cartridge, the printer might be damaged.
Multiple pages are fed through
the printer at once.
Clean the friction pad if it is dirty. See p.110 “Cleaning the
Friction Pad”.
Remove all paper from the tray and fan it gently to get air between the sheets. After that, load it back into the tray.
5
The image is printed on the reverse side of the paper.
Set the paper the other way up.
Paper misfeeds occur frequently.
Check the paper size settings. The size set with the paper size
dial might be different from the actual paper size. Make the
correct dial setting.
See p.47 “Loading Paper and Other Media”.
Use the recommended paper. Avoid using curled, folded,
wrinkled, perforated or glossy paper. See p.44 “Paper not
supported by this printer”.
Clean the paper feed roller, friction pad and/or Registration
roller, if they are dirty. See p.111 “Cleaning the Paper Feed
Roller”.
Thin paper, if printed on both sides, may curl up at the corners and get wrinkled and clogged. Select [Curl Prevention]
[ON] from the [Maintenance] menu.
The control panel error message Open the front cover of the printer and then close it. See p.97
stays on after removing the mis- “Removing Misfed Paper”.
fed paper.
Output are not delivered to the
selected tray you require.
Check the paper size settings. The size selected with the paper size dial might be different from the actual paper size.
Make the correct dial setting.
See p.47 “Loading Paper and Other Media”.
When using the Bypass Tray, set the paper size using the
control panel.
See p.47 “Loading Paper and Other Media”.
When you are using a Windows operating system, the printer driver settings override those set using the control panel.
Set the desired Output Tray using the printer driver. See the
driver's online Help file.
The printed image is different
from the image on the computer.
94
When you use some functions, such as enlargement and reduction, the layout of the image might be different from that
shown in the computer display.
Other Printing Problems
Status
Possible Causes, Descriptions, and Solutions
It takes too much time to resume
printing.
The data is so large or complex that it takes time to process
it. If the Data In indicator is blinking, the data processing is
being done. Just wait until it resumes.
Changing the paper feed direction may sometimes reduce
the time to resume printing.
The image is printed in the
wrong Orientation.
Set the correct Orientation under the “PCL Menu” with the
control panel. See p.162 “PCL Menu”.
Confirm that the setting of Orientation has been set in the application you use.
Set the correct paper size and feed direction that matches
tray settings on the RPCS printer driver.
Part of the image cannot be
printed.
A paper size which is smaller than that selected in the application is used for printing. Load the correct size of paper.
Network configurations you
Print a configuration page and check the network settings.
have made do not become effective.
No e-mail is received when an
Alert occurs, and after resolving
an Alert.
5
Confirm [Notify by E-Mail] is [On]] using the System Menu on
the Control Panel. See p.146 “System Menu”.
Access the printer through the Web Browser, log on as an
Administrator on the Web Image Monitor, and then confirm
the following settings in [Nortification]:
• Device E-mail Address
• Groups to Notify
• Select Groups/Items to Notify
See Web Image Monitor Help for details about the settings.
Access the printer through the Web Browser, log on as an
Administrator on the Web Image Monitor, and then confirm
the settings of the SMTP server in [E-mail]. See Web Image
Monitor Help for details about the settings.
When the power is turned off before the e-mail is transmitted, the e-mail will not be received.
Check the e-mail address set for the destination. Confirm the
printer's operation history using the Web Image Monitor's
System Log menu in [Network]. If the e-mail was sent but not
received, it is possible the destination was incorrect. Also
check the information concerning error mail from the e-mail
server.
The setting for [Notify by E-Mail]
After changing the setting, turn the main unit's power off
on the System Menu was
and then back on again.
changed from [Off] to [On], but email is not arriving.
95
Troubleshooting
Status
Possible Causes, Descriptions, and Solutions
Error notification e-mail was re- Check e-mail is set for sending using the Web Image Moniceived, but no error-solved etor's [Nortification] at the time the error was fixed. You must
mail is received.
click the [Edit] button of [Detailed Settings of Each Item] in [Nortification], and set [Notify when Error] to [Occurs & Fixed] on the
displayed screen. See of the Web Image Monitor Help for details about the settings.
Alert Resolving is set for sending e-mail, but no Alert-resolved e-mail is sent.
If the power of the main unit is turned off after an Alert occurs, the Alert is resolved during the time the power is off: no
Alert-resolved e-mail is sent.
Alert Occurrence and Alert Resolving are set for sending email, but while no Alert Occurrence mail is received, Alert-resolved e-mail is received.s
Alert-notification e-mail is not sent if the problem is resolved
before sending. However, an Alert-resolved e-mail is sent.
Alert-notification level was
If an Alert-notification e-mail, set with the easlier notification
changed, and e-mail stopped ar- level, arrives, later e-mail will not be sent, even if the notifiriving.
cation level is changed after. For example: the toner remaining notification level is 30% and e-mail arrives accordingly, if
it is changed to 20%, no e-mail arrives when the toner remaining level reaches 20%. However, once the toner is
changed, the new notification level is applied.
5
When no date information is in- Make the setting for obtaining time information from the
cluded in sen e-mail, the mail
SNTP server. Refer to the Web Image Monitor's Help to the
server has a malfunction.
settings.
When there is no timeserver, set [E-mail Date] to [On] using the
Control Panel's [System Menu]s.
Note
❒ If the problem cannot be solved, contact your sales or service representative.
96
Removing Misfed Paper
Removing Misfed Paper
When a paper misfeed occurs, an error message appears on the panel display.
The procedure you should follow to remove misfed paper depends on the location of the misfeed, which is indicated on the panel display.
R CAUTION:
• When removing misfed paper, do not touch the fusing section because it
becomes very hot.
Important
❒ Check the following points if paper continues to misfeed.
• Confirm that the setting of the paper size dial matches the size and feed direction of the paper loaded in the paper tray.
• If the friction pad or the paper feed roller is dirty, clean it. For more information, see p.110 “Cleaning the Friction Pad”.
• Confirm that the toner cartridge is set correctly.
❒ If a paper misfeed still occurs, contact your sales or service representative.
❒ Forcefully removing misfed paper may cause paper to tear and leave scraps
of paper in the printer.
❒ Do not leave any scraps of paper in the printer.
When “Remove Misfeed Paper
Tray” Appears
5
A Pull
out the paper tray until it
stops, and then remove misfed
paper.
Important
❒ Forcefully removing misfed paper
may cause paper to tear and leave
scraps of paper in the printer. This
might cause a misfeed and damage
the printer.
ZKEY280E
97
Troubleshooting
B Carefully slide the paper tray into
the printer until it stops.
When "Remove Misfeed
Internal Path/Open Front
Cover" Appears
Important
❒ Forcefully removing misfed paper
may cause paper to tear and leave
scraps of paper in the printer. This
might cause a misfeed and damage
the printer.
ZKEY290E
C While
holding the front cover
with both hands on the left and
right sides, press the release button to open it. Then clear the misfeed condition by closing it,
pressing the left and right side indentations.
5
A While
holding the front cover
with both hands on the left and
right sides, press the release button to open it.
ZKEH120E
B While lifting the front side of the
ZKEY300E
Note
❒ You can apply this procedure
for both the paper tray and the
optional Paper Feed Unit.
❒ To reset the misfeed condition,
open and close the front cover,
then the indicator will be off.
toner cartridge, pull it out of the
printer.
Important
❒ Be sure to put the toner cartridge on a stable, flat surface.
❒ Do not hold the toner cartridge
upside down or stand it vertically.
ZKET110E
98
Removing Misfed Paper
C Pull
out the misfed paper by
holding both sides of paper. Be
careful not to get toner dust on
your hands or clothes.
F Close the front cover by pressing
the left and right side indentations.
ZKEH130E
ZKEY520E
D Holding the grips of the toner car-
tridge, insert it into the printer
until it stops.
Important
❒ If paper is fed from the Bypass
Tray, be sure to remove all the
paper from the Bypass Tray and
close it before opening the front
cover.
5
When "Remove Misfeed Paper
Exit Cover" Appears
ZKET120E
E Lower the toner cartridge when it
makes contact in the back.
ZKET140E
R CAUTION:
• When removing misfed paper,
do not touch the fusing section
because it becomes very hot.
• The fusing unit becomes very
hot. When installing the new fusing unit, turn off the printer and
wait about an hour. After that, install the new fusing unit. Not
waiting for the unit to cool down
can result in a burn.
Important
❒ Forcefully removing misfed paper
may cause paper to tear and leave
scraps of paper in the printer. This
might cause a misfeed and damage
the printer.
99
Troubleshooting
A While
holding the front cover
with both hands on the left and
right sides, press the release button to open it.
C Pull
out the misfed paper by
holding both sides of paper. Be
careful not to get toner dust on
your hands or clothes.
ZKEH120E
B While lifting the front side of the
toner cartridge, pull it out of the
printer.
5
ZKEY520E
D Holding the grips of the toner cartridge, insert it into the printer
until it stops.
Important
❒ Be sure to put the toner cartridge on a stable, flat surface.
❒ Do not hold the toner cartridge
upside down or stand it vertically.
ZKET120E
E Lower the toner cartridge when it
makes contact in the back.
ZKET110E
ZKET140E
100
Removing Misfed Paper
F Close the front cover by pressing
the left and right side indentations.
H Remove the misfed paper.
ZKEY380E
ZKEH130E
I Close the paper exit cover until it
clicks.
Important
❒ If paper is fed from the Bypass
Tray, be sure to remove all the
paper from the Bypass Tray and
close it before opening the front
cover.
5
G If you cannot see the misfed pa-
per, open the paper exit cover.
Place your finger under the indentation in the exit cover, raise it (A)
and pull it backward to open it(B).
ZKEY400E
J While
holding the front cover
with both hands on the left and
right sides, press the release button to open it.
ZKEY390E
ZKEH120E
101
Troubleshooting
K Close the front cover by pressing
the left and right side indentations.
B Remove the rear cover horizontally. Proceed to step M.
ZKEX680E
ZKEH130E
Note
❒ Once all misfed paper is removed, the error message will
disappear and printing will
continue.
5
C Push down the lever on right
side of the Duplex Unit (A
A)
and pull it out until it stops
(B
B).
❒ Proceed to step L if the error
message fails to disappear.
L If the error message is still dis-
played, check the inside of the
fusing unit and remove any paper
inside. Turn off the power and
wait for about an hour before
turning it back on.
Note
❒ Proceed to step C if the optional Duplex Unit is installed.
ZKEX760E
D Push the under board levers
(A
A) and pull the Duplex Unit
out of the printer (B
B).
A Place a finger in the printer's
rear cover finger hole (upper
center) and pull it open.
ZKEY450E
ZKEX670E
102
Removing Misfed Paper
M Lift the lock levers of the fusing
unit as shown in the illustration.
P Insert
the fusing unit until it
stops.
ZKEX222E
N Pull the fusing unit out.
ZKEX224E
Q Push the lock levers of the fusing
unit down until it clicks.
5
ZKEX223E
O While
ZKEX225E
holding the tab, remove
the misfed paper.
Note
❒ Proceed to step T if the optional
Duplex Unit is installed.
R Insert the rear cover to the inside
grooves on both sides of the printer in a horizontal direction.
ZKEY410E
Important
❒ Do not touch the metal part of
the fusing unit. It becomes very
hot. Touching it could result in a
burn.
ZKEX221E
103
Troubleshooting
S Close the rear
cover. Proceed to
step V.
When "Remove Misfeed
Duplex Unit" Appears
R CAUTION:
• When removing misfed paper,
do not touch the fusing section
because it becomes very hot.
ZKEX211E
T Push in the Duplex Unit along the
rails in the back of the printer.
5
Important
❒ Forcefully removing misfed paper
may cause paper to tear and leave
scraps of paper in the Dupelx Unit.
This might cause a misfeed and
damage the printer.
A
Remove the misfed paper inside
of the cover.
A Open the rear cover of the Duplex Unit.
ZKEX231E
U Securely
push the Duplex Unit
into the printer.
ZKEY310E
B Remove the misfed paper.
ZKEX690E
V Turn the power on.
ZKEY320E
104
Removing Misfed Paper
C Close the rear cover of the Duplex Unit.
F Close the cover of the Duplex
Unit.
If the error message appears
again, go to step B.
ZKEY330E
D While lifting the lever (A
A),
open the cover of the Duplex
Unit (B
B).
ZKEY360E
B Pull the Duplex Unit out of the
printer until it stops, and remove
the misfed paper.
A Push down the lever on the
right side of the Duplex Unit
(A
A) and pull it out until it stops
(B
B).
5
ZKEY340E
E Remove the misfed paper.
ZKEX760E
B Lift the guide board inside the
Duplex Unit, and remove the
misfed paper.
ZKEY350E
ZKEY440E
105
Troubleshooting
Important
❒ When A5L paper misfeeds,
you might not be able to remove it by pulling the Duplex Unit out. In this case,
pull the paper tray out and
remove the paper.
C While aligning the power cord
with the groove of the left slide
of the Duplex Unit, insert the
Duplex Unit into back of the
printer aligning the rails inside
of the printer until it is connected.
If the error message appears
again, the misfed paper might
be left in the printer. Confirm
that any torn paper scraps are
not in the inside of the printer.
For more information, see p.98
“When "Remove Misfeed Internal Path/Open Front Cover"
Appears”.
5
ZKEX690E
106
Replacing the Toner Cartridge
Replacing the Toner Cartridge
R WARNING:
• Do not incinerate spilled toner
or used toner. Toner dust
might ignite when exposed to
an open flame.
• Disposal can take place at our
authorized dealer or at appropriate collection sites.
• If you dispose the used toner
cartridges yourself, dispose
of them according to your local regulations.
R CAUTION:
• The inside of the machine could
be very hot. Do not touch the
parts with a label indicating "v"
(means hot surface). Touching
"v" (means hot surface) could
result in a burn.
• Do not eat or swallow toner.
• Keep toner (used or unused) and
toner cartridges out of reach of
children.
• Our products are engineered to
meet the highest standards of
quality and functionality. When
purchasing expendable supplies, we recommend using Only
those specified by an authorized
dealer.
When “Replace Toner Cartridge”
appears on the panel display, the toner is almost empty. Prepare a new
toner cartridge. If the Image Density
gets too light, replace the toner cartridge with a new one.
Important
❒ Do not expose the toner cartridge
to light for a long time. Do not
leave the front cover open for a
long time. If the toner cartridge is
exposed to a light for a long time,
the toner cartridge might be damaged and print quality might be reduced.
Note
❒ Do not stand or place the toner cartridge upside-down.
❒ The actual number of printed pages you get from a particular toner
cartridge depends on the type and
size of paper you are using, the
contents of the print images, and
printing environment conditions.
All this means that a toner cartridge might require replacement
sooner than the normal life described on p.198 “Consumables”.
5
A While
holding the front cover
with both hands on the left and
right sides, press the release button to open it.
ZKEH120E
107
Troubleshooting
B Be sure to put the toner cartridge
on a stable, flat surface.
Note
❒ Do not put the toner cartridge
on an unstable or tilted surface.
E Place the toner cartridge on a flat
surface. Pull out the tape inside
the unit horizontally while holding the cartridge with one hand as
shown in the illustration.
ZKET151E
ZKET110E
C Wipe around the metallic Regis-
5
tration roller by turning with a
soft damp cloth.
ZKEX461E
Important
❒ Do not use chemical cleaner or
organic solvent such as thinner
or benzene.
D Take the new toner cartridge from
the box.
108
Note
❒ Be sure to remove the tape completely before installing the new
toner cartridge, otherwise the
printer might be damaged.
❒ Keep the toner cartridge horizontal when pulling out the toner seal. Pulling out the toner seal
with the cartridge upright or
tilted can cause printer failure.
❒ Be careful not to get toner dust
on your hands or clothes.
❒ Do not shake or shock the toner
cartridge after pulling out the
toner seal to avoid dirt on paper
surfaces, toner spillage, or
printer failure.
Replacing the Toner Cartridge
F Holding the grips of the cartridge,
insert it into the printer until it
stops.
Important
❒ Do not close the front cover
with force. If you cannot close
the cover easily, pull out the
toner cartridge from the printer
and insert it again. After that,
close the front cover again.
ZKET120E
G Lower the toner cartridge when it
touches in the back.
5
ZKET140E
H Close the front cover by pressing
the left and right side indentations.
ZKEH130E
109
Troubleshooting
Cleaning and Adjusting the Printer
D Wipe the friction pad with a soft
Cleaning the Friction Pad
If the friction pad is dirty, a multifeed or a misfeed might occur. In this
case, clean the pad as follows:
damp cloth. After that, wipe it
with a dry cloth to remove the water.
A Pull
out the paper tray until it
stops.
5
ZKEY700E
ZKDX270J
B While lifting the front side of the
tray, pull it out of the printer.
Important
❒ Do not use chemical cleaner or
organic solvent such as thinner
or benzene.
E Lift the front of the tray, and slide
it carefully into the printer until it
stops.
ZKEY140E
C Place
the tray on a flat surface.
When there is paper in the tray,
remove paper.
110
ZKDY150J
Important
❒ Do not slide the paper tray in
with force. If you do, the front
and side guides might move.
Cleaning and Adjusting the Printer
Note
❒ If misfeeds or multi-feeds of paper occur after cleaning the friction pad, contact your sales or
service representative.
❒ Follow the same procedure to
clean the friction pad of the optional Paper Feed Unit and the
Envelope Feeder Unit.
B Pull out the plug from the socket.
Remove all the cables from the
printer.
C Pull
out the paper tray until it
stops.
Cleaning the Paper Feed
Roller
If the paper feed roller is dirty, a misfeed might occur. In this case, clean
the roller as follows:
R CAUTION:
• When lifting the printer, use the
grips on both sides of the printer,
otherwise the printer might fall
and cause personal injury.
ZKDX270J
D While lifting the front side of the
5
tray, pull it out of the printer.
• When you move the printer, unplug the power cord from the wall
outlet to avoid a fire or an electric
shock.
• When you pull out the plug from
the socket, grip the plug to avoid
damaging the cord and causing
a fire or an electric shock.
ZKEY140E
E Move the printer to the edge of a
stable table or desk.
Note
❒ The Paper Feed Unit's Paper Feed
Roller can be cleaned in the same
manner.
ZKEM110E
ZKEM200E
A Turn off the power switch.
111
Troubleshooting
Important
❒ Do not put the printer on an unstable or tilted surface.
❒ If the printer is equipped with
the optional Paper Feed Unit,
do not move the printer and
unit together as they are not securely attached.
❒ When lifting the printer, confirm that the optional Paper
Feed Unit is not attached to the
printer.
H While sliding the green lock lever
to the left (A
A), set the paper feed
roller to its original position (B
B).
After that, return the green lock
lever to its original position (C
C).
F Slide the green lock lever to the
left (A
A ), so that the paper feed
roller can be released (B
B).
ZKEM130E
Note
❒ Confirm that the green lock lever secures the roller correctly
by confirming that the roller rotates smoothly.
5
I Move the printer back to its original position. Lift the front of the
tray, and slide it carefully into the
printer until it stops.
ZKEM120E
G Wipe the rubber part of the roller
with a soft damp cloth. After that,
wipe it with a dry cloth to remove
the water.
Important
❒ Do not use chemical cleaner or
organic solvent such as thinner
or benzene.
ZKDY150J
Important
❒ Do not slide the paper tray in
with force. If you do, the front
and side guides might move.
J Insert the plug of the power cord
into the wall socket securely.
Connect all the cables that were
removed in step B.
112
Cleaning and Adjusting the Printer
K Turn on the power switch.
C Pull the toner cartridge out of the
Note
❒ Follow the same procedure to
clean the paper feed roller of the
optional Paper Feed Unit.
Cleaning the Registration
Roller
printer by holding the grips of the
cartridge.
Note
❒ Do not hold the toner cartridge
upside down or stand it vertically.
❒ Do not put the toner cartridge
on an unstable or tilted surface.
If the Registration roller is dirty, a
misfeed might occur. In this case,
clean the roller as follows:
R WARNING:
• Be sure to turn off the power
switch and wait for about 15
minutes before cleaning the
Registration roller. Not waiting for the printer to cool
down can result in a burn.
R CAUTION:
• The inside of the machine could
be very hot. Do not touch the
parts with a label indicating "v"
(means hot surface). Touching
"v" (means hot surface) could
result in a burn.
5
ZKET110E
D Wipe around the metallic Registration roller by turning with a
soft damp cloth.
A Turn off the power switch.
B While holding the front
cover
with both hands on the left and
right sides, press the release button to open it.
ZKEX461E
Important
❒ Do not use chemical cleaner or
organic solvent such as thinner
or benzene.
ZKEH120E
113
Troubleshooting
E Holding the grips of the toner car-
tridge, insert it into the printer
until it stops.
Important
❒ Carefully close the front cover.
If you cannot close the cover
easily, pull the toner cartridge
out of the printer and insert it
again. After that, close the front
cover again.
H Turn on the power switch.
Adjusting the Image Density
ZKET120E
F Push down the toner cartridge to
settle it in appropriate position.
5
You can adjust the Image Density
when the print side of the page is a
shaded or print image is too light.
Important
❒ Extreme settings may create printouts that appear dirty.
❒ Image Density settings should be
made from the application or the
printer driver whenever possible.
A Press {Menu}}.
On Line
Menu
ZKET140E
G Close the front cover by pressing
the left and right side indentations.
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
"Menu" appears on the panel display.
ZKEH130E
114
Cleaning and Adjusting the Printer
B Press {U} or {T} to display the
"Maintenance" menu, and then
press {Enter #}
}.
On Line
Job Reset
F Press {On Line}}.
On Line
Menu
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
Data In
ZKEP060E
The following message appears on
the panel display.
"Ready" appears on the panel display.
Ready
5
Maintenance:
Image Density
C Press {Enter #}}.
Image Density:
(-3 +3)
0
D Press {U} or {T} to set the Image
Density value.
Note
❒ To maintain a darker image under high volume printing conditions, we highly recommended
that you select 3 from the control panel.
❒ You can adjust the Image Density in seven steps from -3 to +3.
Increasing the value makes the
printouts darker and decreasing
the value makes the printouts
lighter.
E Press {Enter #}}.
115
Troubleshooting
Adjusting the Registration of
the Trays
You can adjust the Registration of
each tray. The vertical adjustment is
used for all trays. Normally, you need
not update the Registration. But
when the optional Paper Feed Unit or
the Duplex Unit is installed, updating
the Registration is useful in some
case.
The following procedure describes
how to adjust Tray 1. You can use the
same procedure to adjust the other
tray as well.
C Press {U} or {T} to display "Reg-
istration", and then press {Enter
#}
}.
The following message appears on
the panel display.
Registration:
Prt. Test Sheet
D Print the test sheet to preview the
settings you have made.
A Press {Menu}}.
5
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
ZCEX480J
Data In
ZKEP020E
"Menu" appears on the panel display.
B Press {U} or {T} to display the
"Maintenance" menu, and then
press {Enter #}
}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Prt. Test Sheet
Tray 1
B Press {U} or {T} to display the
tray you want to adjust, and
then press {Enter #}
} to print the
test sheet. Wait for a few seconds.
The following message appears
on the panel display.
Printing...
Data In
ZKEP060E
116
A After confirming that "Prt. Test
Sheet" is on the panel display,
press {Enter #}
}.
The following message appears
on the panel display.
Maintenance:
Image Density
Cleaning and Adjusting the Printer
E Adjust
the Registration by confirming the position of the printed image of the test sheet.
The following is an example of adjusting the margin on the test sheet
equally.
A Press {U} or {T} to display
"Adjustment", and then press
{Enter #}
}.
The following message appears
on the panel display.
Adjustment:
Horiz.: Tray 1
B Press {U} or {T} to display the
tray you want to adjust, and
then press {Enter #}
}.
The following message appears
on the panel display.
F Print the test sheet to check the
settings you have made.
G Repeat steps C and D to adjust the
Registration if necessary.
H Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
5
“Ready” appears on the panel display.
Ready
Horiz.: Tray 1
(-4.0 +4.0) 0.0
C Press {U} or {T} to set the digit
of the Registration value (mm).
Feed direction
The vertical
The
horizonal
Printable area
TS3X001N
Note
❒ Increase the value to shift the
print area to the positive direction, and decrease to shift
to the negative direction.
❒ Pressing {U} or {T} makes
the value increase or decrease by 0.5 mm step.
D Press {OK}
}.
117
Troubleshooting
5
118
6. Making Printer Settings with
the Control Panel
Menu Chart
This section describes how to change the default settings of the printer and provides information on the parameters included in each menu. Some items in the
menu appear Only when certain options are installed.
Category
Function menu
Sample Print
*1
⇒ p.61
Select Action / Error File(s)
Locked Print
*1
⇒ p.66
Select Action / Error File(s)
Paper Input⇒ p.124
Bypass Size
Tray Paper Size
Paper Type
Tray Locking
Tray Priority
List/Test Print⇒ p.128
Config.P/Er.log
Config. Page
Error Log
Menu List
PS Font List
PCL Config.Page
PDF Config.Page
Hex Dump
Maintenance⇒ p.134
Image Density
Registration
Curl Prevention
HDD Format
WL.LAN Signal *2
WL.LAN Defaults *2
Key Repeat
Menu Protect *3
Ppr.Size Errors *3
119
Making Printer Settings with the Control Panel
Category
System⇒ p.146
Function menu
Prt. Err Report
Auto Continue
Memory Overflow
Copies
Printer Lang.
Sub Paper Size
Page Size
Edge-Edge Print
Def.Print Lang.
Duplex *4
Energy Saver
Memory Usage
Unit of Measure
Edge Smoothing
Toner Saving
6
Spool Printing
Letterhead Mode
RAM Disk
Notify by E-Mail
E-Mail Date *3
Host Interface⇒ p.154
I/O Buffer
I/O Timeout
Network Setup
IEEE 1394 Setup *5
IEEE 802.11b *6
USB Setting *3
Bluetooth *7
120
Menu Chart
Category
PCL Menu⇒ p.162
Function menu
Orientation
Form Lines
Font Source
Font Number
Point Size
Font Pitch
Symbol Set
Courier Font
Ext. A4 Width
Append CR to LF
Resolution
PS Menu
Data Format
Resolution
PDF Menu
PDF: Change PW
Resolution
6
Language⇒ p.172
*1
*2
*3
*4
*5
*6
*7
The “Sample Print” menu and the “Locked Print” menu appear Only when the optional Hard Disk Drive is installed.
The "WL.LAN Signal" menu appears Only when "IEEE 802.11b" is selected in "LAN
Type" in the Host Interface menu.
While the printer is On Line, press {Enter #}
}, and then press {Escape}
}. Finally, press
{Menu}
}. You can access the "Menu Protect", "Series Prnt.Job", "Ppr.Size Errors", "EMail Date", and "USB Setting" on the panel display.
The “Duplex” menu appears Only when the optional Duplex Unit is installed.
The “IEEE 1394 Setup” menu appears Only when the optional 1394 Interface Unit is
installed.
The “IEEE 802.11b” menu appears Only when the optional 802.11b Interface Unit is
installed.
The “Bluetooth” menu appears Only when the optional Bluetooth Interface Unit is
installed.
121
Making Printer Settings with the Control Panel
Accessing the Main Menu
Press {Menu}
}, and “Menu” appears on the panel display.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
This menu shows the following nine items which can be displayed one by one
pressing {U} or {T}.
• Sample Print
• Locked Print
• Paper Input
• List/Test Print
• Maintenance
• System
• Host Interface
• PCL Menu
• PS Menu
• PDF Menu
• Language
6
Note
❒ "Sample Print" and "Locked Print" appear Only when the optional Hard Disk
Drive is installed.
❒ {T}: Press to go to the next page.
❒ {U}: Press to go back to the previous page.
122
Accessing the Main Menu
❒ After making the printer settings, be sure to return to the previous menu by
pressing {Escape}
}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP040E
❒ After making the printer settings, press {On Line}
} to return to the “Ready”
condition.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
6
Data In
ZKEP010E
❒ The revised settings are not canceled even if the power switch is turned off.
123
Making Printer Settings with the Control Panel
Paper Input Menu
There are five menu items in the “Paper Input” menu.
• Bypass Size
• Tray Paper Size
• Paper Type
• Tray Locking
• Tray Priority
Reference
For more information about loading paper in the tray, see p.47 “Loading Paper and Other Media”.
Paper Input Parameters
Menu
Bypass Size
6
Description
The paper size for the Bypass Tray.
For more information about paper sizes that can be set in the Bypass Tray, see p.35 “Paper and Other Media Supported by This
Printer”.
Tray Paper Size
The paper size for each tray.
When you select sizes that are not indicated on the paper size dial
of Tray 1, Tray 2 or Tray 3, you should set the dial to “p” and
then select the paper size here.
❖ Tray 1
For more information about paper sizes that can be set in the
Tray 1, see p.35 “Paper and Other Media Supported by This
Printer”.
❖ Tray 2
For more information about paper sizes that can be set in the
Tray 2, see p.35 “Paper and Other Media Supported by This
Printer”.
❖ Tray 3
For more information about paper sizes that can be set in the
Tray 3, see p.35 “Paper and Other Media Supported by This
Printer”.
Note
❒ Only the installed trays appear on the panel display.
124
Paper Input Menu
Menu
Paper Type
Description
If you use different kinds of paper, you set the paper type for Tray
1, Tray 2, Tray 3 or Bypass Tray.
❖ Tray 1, Tray 2, Tray 3
Plain Paper, Recycled Paper, Special Paper, Color Paper, Letterhead, Preprinted, Prepunched, Bond Paper, Cardstock
❖ Bypass Tray
Plain Paper, Recycled Paper, Special Paper, Color Paper, Letterhead, Preprinted, Prepunched, Labels, Bond Paper, Cardstock, Transparency, Thick Paper
Note
❒ Default : Plain Paper
❒ Only the installed trays appear on the panel display.
Tray Locking
If you use different kinds of paper, you can lock a tray to prevent
printing on wrong paper such as Letterhead or colored paper.
When "Auto Tray Select" is selected in the Paper Source selections
from the printer driver, the locked tray will not be used.
Tray 1, Tray 2, Tray 3, Bypass Tray
6
Note
❒ Only the installed trays appear on the panel display.
❒ You cannot lock multiple trays.
❒ If you want to use the locked tray, you must select the tray
from the printer driver.
❒ When a locked tray is selected from the printer driver, the
printer does not search for another tray.
Tray Priority
You can set priority tray for paper feed when "Auto Tray Select"
is selected in the Paper Source selections from the printer driver.
When printing from DOS, the tray selected here is used when no
tray is selected for a print job.
Tray 1, Tray 2, Tray 3, Bypass Tray
Note
❒ Default : Tray 1
❒ Only the installed trays appear on the panel display.
❒ It is recommended that you load paper of the size and direction you most frequently use in the tray selected with "Tray
Priority".
125
Making Printer Settings with the Control Panel
Changing the Paper Input Menu
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the panel display.
B Press {U} or {T} to display the “Paper Input” menu.
Menu:
Paper Input
6
C Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
D Press {U} or {T} to display “Tray Priority”.
Paper Input:
Tray Priority
E Press {Enter #}}.
The following message appears on the panel display.
Tray Priority:
*Tray 1
126
Paper Input Menu
F Press {U} or {T} to select the tray type you want to use.
G Press {Enter #}}. Wait for a few seconds.
H Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
“Ready” appears on the panel display.
Ready
6
127
Making Printer Settings with the Control Panel
List/Test Print Menu
There are eight menu items in the “List/Test Print” menu.
• Config.P/Er.log
• Config. Page
• Error Log
• Menu List
• PS Font List
• PCL Config.Page
• PDF Config.Page
• Hex Dump
List/Test Print Parameters
Menu
6
128
Description
Config.P/Er.log
You can print the configuration page and error log.
Config. Page
You can print the current configuration of the printer. See p.130
“Printing a Configuration Page”.
Error Log
You can print an error report.
Menu List
You can print the Menu List which shows the function menus of
this printer.
PS Font List
You can print the current configuration and installed PS Font List
of PostScript.
PCL Config.Page
You can print the current configuration of PCL.
PDF Config.Page
You can print the Adobe® PDF Reference, Memory/HDD status,
Printing Configuration, and Resident Fonts.
Hex Dump
You can print the data sent by the computer using the Hex Dump
mode.
List/Test Print Menu
Printing the Configuration Page and Error Log
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the panel display.
B Press {T} or {U} to display the “List/Test Print” menu.
Menu:
List/Test Print
6
C Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
List/Test Print:
Config.P/Er.log
D Press {Enter #}}.
The following message appears on the panel display.
Printing...
You can print the configuration page and error log.
129
Making Printer Settings with the Control Panel
Important
❒ If you cannot print a configuration page correctly, check for an error message on the panel display. For more information about error messages, see
p.73 “Error & Status Messages on the Control Panel”.
E Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
“Ready” appears on the panel display.
Ready
6
Printing a Configuration Page
Reference
For more information, see p.132 “Interpreting the Configuration Page”.
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the panel display.
B Press {T} or {U} to display the “List/Test Print” menu.
Menu:
List/Test Print
130
List/Test Print Menu
C Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
List/Test Print:
Config.P/Er.log
D Press {T} or {U} to display the “Config.Page” menu.
List/Test Print:
Config.Page
6
E Press {Enter #}}.
The following message appears on the panel display.
Printing...
The configuration page will be printed in a short time.
Important
❒ If you cannot print a configuration page correctly, check for an error message on the panel display. For more information about error messages, see
p.73 “Error & Status Messages on the Control Panel”.
131
Making Printer Settings with the Control Panel
F Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
“Ready” appears on the panel display.
Ready
Interpreting the Configuration Page
6
System Reference
❖ Printer ID
Shows the serial number assigned to the board by its manufacturer.
❖ Firmware Version
• Firmware
Shows the version number of the printer firmware.
• Engine
Shows the version number of the printer engine.
• NCS
Shows the version number of the Network interface.
❖ Pages Printed
Shows the total number of pages printed by the printer to date.
❖ Total Memory
Shows the total amount of memory (SDRAM) installed on the printer.
❖ Printer Language
Shows the version number of the printer driver language.
❖ Controller Option
The item(s) appears when the controller option(s) is installed.
❖ Options
Shows the optional trays that you installed.
132
List/Test Print Menu
Paper Input
Shows the settings made under the “Paper Input” menu.
Reference
For more information, see p.124 “Paper Input Menu”.
Maintenance
Shows the settings made under the “Maintenance” menu.
Reference
For more information, see p.134 “Maintenance Menu”.
System
Shows the settings made under the “System” menu.
Reference
For more information, see p.146 “System Menu”.
6
PCL Menu
Shows the settings you made under the “PCL Menu”.
Reference
For more information, see p.162 “PCL Menu”.
Host Interface
Shows the settings you made under the “Host Interface” menu.
When DHCP is Active on the network, the actual IP Address, Subnet Mask and
Gateway Address appear in parentheses on the configuration page.
Reference
For more information about “Host Interface” menu, see p.154 “Host Interface
Menu”.
Interface Information
Shows the interface information.
Error Log
Shows the log of printer errors.
133
Making Printer Settings with the Control Panel
Maintenance Menu
There are 10 menu items in the “Maintenance” menu.
• Image Density
• Registration
• Curl Prevention
• HDD Format
• WL.LAN Signal
• WL.LAN Defaults
• Key Repeat
• Menu Protect
• Ppr.Size Errors
Note
❒ “HDD Format” appears Only when the optional Hard Disk Drive is installed.
For more information, see “Hard Disk Drive Type 2600” in the Setup Guide.
6
134
Maintenance Menu
Maintenance Menu Parameters
Menu
Image Density
Description
You can select the print Image Density.
-3 to 3
Reference
For more information, see p.114 “Adjusting the Image Density”.
Registration
❖ Prt. Test Sheet
You can print the Registration test sheet.
Tray 1, Tray 2, Tray 3, Bypass Tray, Duplex backside
Note
❒ Default : Tray 1
❒ Only the installed trays appear on the panel display.
❖ Adjustment
You can select the start position for printing on a page.
Horiz.: Tray 1, Horiz.: Tray 2, Horiz.: Tray 3, Horiz.: Bypass,
Horiz.: Dup.Back, Vert.: All Trays, Vert.: Dup.Back
-4 to 4
6
Note
❒ Default : Horiz.: Tray 1
❒ The Registration value is not a default.
❒ Only the installed trays appear on the panel display.
Reference
For more information, see p.116 “Adjusting the Registration of the Trays”.
Curl Prevention
You can control the fuser temperature to prevent paper from curling.
Note
❒ Default: Off
❒ Use this mode Only when paper misfeed occurs frequently
during Duplex printing.
HDD Format
After installing the Hard Disk Drive, format it.
Note
❒ This menu appears Only when the optional Hard Disk Drive
is installed.
Reference
For more information about formatting the Hard Disk Drive,
see p.140 “Formatting Hard Disk Drive Type 2600”.
135
Making Printer Settings with the Control Panel
Menu
WL.LAN Signal
Description
You can check the signal strength when using the wireless LAN.
Note
❒ This menu appears Only when the optional Wireless Interface
Unit is installed.
Reference
For more information about displaying the signal strength, see
p.141 “Displaying the Signal Strength”.
WL.LAN Defaults
You can reset the wireless LAN settings to the default.
Note
❒ This menu appears Only when the optional Wireless Interface
Unit is installed.
Key Repeat
You can scroll through the menu by holding this key down.
Note
❒ Default: On
Menu Protect *1
6
This procedure lets you protect menu settings against accidental
changes. It makes it impossible to change the menu settings you
make with the normal procedure unless you perform the required
key operation. In a network environment, protecting settings restricts who can change menu settings to network administrators.
• Level 1
• Level 2
• Off
Note
❒ Default: Off
❒ While the printer is On Line, press the {Enter #}
} key, and then
press the {Escape}
} key, finally press the {Menu}
} key. You can
access the "Menu Protect" menu on the panel display.
❒ You can protect the "Maintenance", "System", "Host Interface"
and "Language" menu on Level 1.
❒ You can protect the "Paper Input", "Maintenance", "System",
"Host Interface" and "Language" menu on Level 2.
Ppr.Size Errors *1
You can select whether to have an error report printed when the
paper size setting for the tray differs from the actual size of the paper in the tray. You can also select whether to have an error message displayed when feeding paper from the tray.
Note
❒ Default: Detect
❒ When it is "Detect", it prints with the paper size that was set
when the error message appeared.
*1
136
While the printer is Online, press {Enter #}
}, and then press {Escape}
}. Finally, press
}. You can access the "Menu Protect" , and "Ppr.Size Errors " menu on the panel
{Menu}
display.
Maintenance Menu
Changing the Maintenance Menu
Setting and canceling the menu protection
Explains the method of setting and canceling menu protection.
Locking the panel with Menu Protect
A Check if the On Line indicator is on. If not, press {On Line}} to enter the
"Ready" condition.
B Press {Enter #}}, then {Escape}}, and then {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
6
Data In
ZKEP050E
"Menu" appears on the panel display.
C Press {U} or {T} to display the “Maintenance” menu, and then press {Enter
#}
}.
The following message appears on the panel display.
Maintenance:
Image Density
D Press {U} or {T} to display “Menu Protect”.
Maintenance:
Menu Protect
E Press {Enter #}}.
The following message appears on the panel display.
Menu Protect:
*Off
137
Making Printer Settings with the Control Panel
F Press {U} or {T} to select the levels desired, and then press {Enter #}}. Wait
for a few seconds.
Menu Protect:
*Level 1
G Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
"Ready" appears on the panel display.
6
Ready
Canceling the protection
A Check the On Line indicator is on. If it is not, press {On Line}} to enter the
"Ready" condition.
B Press {Enter #}}, then {Escape}}, and then {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP050E
“Menu” appears on the panel display.
138
Maintenance Menu
C Press {U} or {T} to display “Maintenance” menu, and then press {Enter #}}.
The following message appears on the panel display.
Maintenance:
Image Density
D Press {U} or {T} to display “Menu Protect”, and then press {Enter #}}.
Maintenance:
Menu Protect
E Press {Enter #}}.
The following message appears on the panel display.
Menu Protect:
*Level 1
F Press {U} or {T} to display “Off”, and then press {Enter #}}. Wait for a few
seconds.
6
Menu Protect:
*Off
G Press {On Line}}.
“Ready” appears on the panel display.
139
Making Printer Settings with the Control Panel
Formatting Hard Disk Drive Type 2600
If you are formatting the Hard Disk Drive for the first time, follow the procedures below using the control panel.
A Press {Menu}}.
“Menu” appears on the panel display.
B Press {U} or {T} to display “Maintenance” menu.
Menu:
Maintenance
C Press {Enter #}}.
The following message appears on the panel display.
Maintenance:
Image Density
D Press {U} or {T} to display “HDD Format”.
6
Maintenance:
HDD Format
E Press {Enter #}}.
The following message appears on the panel display.
HDD Format:
Press# to Start
F Press {Enter #}}.
Important
❒ Do not turn off the printer while formatting the Hard Disk Drive. Turning
off the printer while formatting the Hard Disk Drive can damage the Hard
Disk Drive.
If you successfully format the Hard Disk Drive, the following message appears on the panel display.
Completed
Restart Printer
G Turn off the power switch, and then turn it back on.
140
Maintenance Menu
Displaying the Signal Strength
If you need to check the IEEE 802.11b (Wireless LAN) signal, select "WL.LAN
Signal" in the "Maintenance" menu.
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the panel display.
B Press {T} or {U} to display the “Maintenance” menu.
6
Menu:
Maintenance
C Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
Maintenance:
Image Density
D 4 Press {T} or {U} to display "WL.LAN Signal".
Maintenance:
WL.LAN Signal
141
Making Printer Settings with the Control Panel
E Press {Enter #}}.
One of the following messages appears on the panel display.
WL.LAN Signal
Good
100%
WL.LAN Signal
Fair
70%
WL.LAN Signal
Poor
40%
WL.LAN Signal
Unavailable 18%
Note
❒ If "WL.LAN Signal" is not displayed, "IEEE 802.11b" has not been selected
for "LAN Type" in "Network Setup" of the Host Interface menu. Select
"IEEE 802.11b" for "LAN Type", and then check the "WL.LAN Signal" in
the Maintenance menu again.
❒ If "Ad hoc" in "Comm. Mode" of "IEEE 802.11b" in the Host Interface menu
is selected, you cannot check the signal. Select "Infrastructure" and then
check it again.
❒ Every time you press {Enter #}
}, the signal is updated.
❒ The signal is indicated as "Good" if the signal strength is 86-100%, "Fair" if
the strength is 61-85%, "Poor" if the strength is 31-60%, and "Unavailable"
if the strength is 0-30%. If the signal is unstable or unavailable, remove obstacles or move the printer to a place where the signal can be received.
❒ Using wireless devices or microwave sources near the printer might affect
the signal.
6
F Press {Escape}}.
142
Maintenance Menu
G Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
“Ready” appears on the panel display.
Ready
6
143
Making Printer Settings with the Control Panel
Resetting the IEEE 802.11b (Wireless LAN) Settings
If you need to reset the wireless LAN setting, select "WL.LAN Defaults" in the
Maintenance menu.
Note
❒ The four items that can be reset in "IEEE 802.11b" of the Host Interface menu
are "Comm. Mode", "Channel", "Trans. Speed", and "WEP Setting". Other
items that can be reset are the SSID settings, the WEP key settings, and the
wireless LAN settings that can be made with telnet.
A Press {Menu}}.
On Line
6
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the panel display.
B Press {T} or {U} to display the “Maintenance” menu.
Menu:
Maintenance
C Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
Maintenance:
Image Density
144
Maintenance Menu
D Press {T} or {U} to display "WL.LAN Defaults".
Maintenance:
WL.LAN Defaults
E Press {Enter #}}.
WL.LAN Defaults
Reset→Defaults?
F Press {Enter #}}.
The following message appears on the panel display.
Defaults reset
Press # to exit
G Press {Enter #}}.
The following message appears on the panel display.
6
Setting change
in process
The wireless LAN setting value is reset.
“Ready” appears on the panel display.
Ready
145
Making Printer Settings with the Control Panel
System Menu
There are 19 menu items in the “System” menu.
• Prt. Err Report
• Auto Continue
• Memory Overflow
• Copies
• Printer Lang.
• Sub Paper Size
• Page Size
• Edge-Edge Print
• Def.Print Lang.
• Duplex
• Energy Saver
• Memory Usage
• Unit of Measure
• Edge Smoothing
• Toner Saving
• Spool Printing
• Letterhead Mode
• RAM Disk
• Nortify by E-Mail
• E-Mail Date
6
System Parameters
Menu
Prt. Err Report
Description
You can select whether or not to have an error report printed
when a printer error or memory error occurs.
• On
• Off
Note
❒ Default: Off
146
System Menu
Menu
Auto Continue
Description
You can set whether Auto Continue is enabled. When it is on,
printing continues after a system error occurs.
• Off
• 0 minutes
• 1 minute
• 5 minutes
• 10 minutes
• 15 minutes
Note
❒ Default: Off
❒ When it is on and certain types of error occur, the current job
might be canceled, and the next job started automatically.
Memory Overflow
You can select whether the memory overflow error report is printed when the data is too large and cannot be processed.
• Not Print
• Error List
Note
6
❒ Default: Not Print
Copies
You can specify how many pages to print.
This setting is disabled if the number of pages to print is already
specified with the printer driver or a command.
• 1-999
Printer Lang.
You can specify the printer language.
• Auto Detect
• PCL
• PS
• PDF
• XPDL_0
• XPDL_1
Note
❒ Default: Auto Detect
Sub Paper Size
You can select whether the printer automatically selects the paper
tray containing paper of the specified size.
• Off
• Auto
Note
❒ Default: Off
147
Making Printer Settings with the Control Panel
Menu
Page Size
Description
You can specify the default paper size.
8 1/2 x 14, 8 1/2 x 11, 5 1/2 x 8 1/2, 8 x 13, 8 1/2 x 13. 8 1/4 x 13,
A4(210x297), B5 JIS(182x257), A5(148x210), A6(105x148),
16K(195x267), 4 1/8 x 9 1/2, 3 7/8 x7 1/2, C5 Env.(162x229), C6
Env(114x162), DL Env.(110x220), CustomSize
Note
❒ Default: 8 1/2 x 11
Edge-Edge Print
You can print on the complete area of an A4 sheet leaving no border on any edge.
Important
❒ When printing again after changing the setting to “On”, the
paper's reverse side may be dirtied.
Note
❒ Default: Off
Def.Print Lang.
You can specify the default printer language.
• PCL
• PS
6
• PDF
• XPDL_0
• XPDL_1
Note
❒ Default: PCL
Duplex
You can select whether you want to print on both sides of each
page.
• Off
• Short Edge Bind
• Long Edge Bind
Note
❒ Default: Off
❒ This menu appears Only when the optional Duplex Unit is installed.
148
System Menu
Menu
Energy Saver
Description
You can set how many minutes the printer waits before switching
to Energy Saver mode. Energy Saver mode reduces electric power
consumption.
On, Off
1 minute, 5 minutes, 15 minutes, 30 minutes, 45 minutes, 60 minutes
Note
❒ Default: On
❒ Default: 30 minutes
❒ If there is an error with the printer, the printer will not switch
to Energy Saver mode.
❒ When the printer switches to Energy Saver mode, the Power
indicator turns off while the On Line indicator stays on.
Memory Usage
You can select memory to be used from "Font Priority" or "Frame
Priority" according to the paper size, Resolution or printer language.
• Font Priority
This setting uses memory for registering fonts.
• Frame Priority
This setting uses memory for high speed printing.
6
Note
❒ Default: Frame Priority
Reference
For more information, see p.187 “Memory Capacity and Paper
Size”.
Unit of Measure
You can select "mm" or "inch" for the custom paper sizes.
Note
❒ Default: mm
Edge Smoothing
You can set whether Edge Smoothing is enabled. When it is on,
jagged lines appear more smoothly. Set it to off when the print image contains fine gradation in tone.
• On
• Off
Note
❒ Default: On
❒ If "Toner Saving" is "On", "Edge Smoothing" is ignored even if
it is "On".
149
Making Printer Settings with the Control Panel
Menu
Toner Saving
Description
You can select whether or not Toner Saving is enabled.
• On
• Off
Note
❒ Default: Off
❒ If "Toner Saving" is "On", "Edge Smoothing" is ignored even if
it is "On".
Spool Printing
You can select whether all of the print data is spooled to the Hard
Disk Drive before printing.
• On
• Off
Note
❒ Default: Off
❒ Spooling stores the print job sent by a computer temporarily in
the printer, transfers the print job, and then prints it.
❒ This menu appears Only when the optional Hard Disk Drive
is installed.
6
Letterhead Mode
You can select whether or not to do letterhead printing. If you select letterhead printing and duplex printing, the last sheet of a
print job with an odd number of pages is printed on both sides.
• Off
• Auto Detect
• On (Always)
Note
❒ Default: Off
❒ Duplex printing is canceled if the paper size does not allow it.
❒ If printing changes from single-sided to duplex during printing, the second and later copies with collate will all be duplex.
If you want the second and later copies to be single-sided, select a paper size that does not allow duplex printing.
❒ When using letterheads, be careful how you orient the paper.
RAM Disk
If the optional hard disk drive is not installed, when executing
PDF Direct Print set a value of 2 MB or higher.
• 0MB
• 2MB
• 4MB
• 8MB
• 16MB
Note
❒ Default: 4MB
150
System Menu
Menu
Description
Notify by E-Mail
You can have error details sent to a preset e-mail address when an
error occurrs in the printer.
• Off
• On
Important
❒ After changing the setting, turn off the power of the main unit
briefly, and then back on again.
Note
❒ Default: On
E-Mail Date
If there is no timeserver, set to “On” if mail without date information causes problems for the mail server. Through its software, email sent by this device includes a date and time (based on a provisional date and time using January 1st of the year of manufacture as the initial date).
• Off
• On
Note
❒ Default: Off
6
❒ While the printer is On Line, press the {Enter #}
} key, and then
press the {Escape}
} key, finally press the {Menu}
} key. You can
access the "Menu Protect" menu on the panel display.
Changing the System Menu
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the panel display.
B Press {U} or {T} to display the “System” menu.
Menu:
System
151
Making Printer Settings with the Control Panel
C Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
System:
Prt.Err Report
D Press {U} or {T} to display “Energy Saver ”.
System:
Energy Saver
6
E Press {Enter #}}.
The following message appears on the panel display.
Energy Saver :
E.Saver On/Off
F Press {U} or {T} to display "E. Saver Timer".
Energy Saver :
E. Saver Timer
G Press {Enter #}}.
The following message appears on the panel display.
E. Saver Timer
*15 minutes
H Press {U} or {T} to select how many minutes the printer waits before
switching to Energy Saver mode.
I Press {Enter #}}.
The screen returns to step F in a few seconds.
152
System Menu
J Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
“Ready” appears on the panel display.
Ready
6
153
Making Printer Settings with the Control Panel
Host Interface Menu
There are seven menu items in the “Host Interface” menu.
• I/O Buffer
• I/O Timeout
• Network Setup
• IEEE 1394 Setup
• IEEE 802.11b
• USB Setting
• Bluetooth
Host Interface Parameters
Menu
I/O Buffer
Description
You can set the size of the I/O Buffer. Normally it is not necessary
to change this setting.
128 KB, 256 KB, 512 KB
6
Note
❒ Default: 128 KB
I/O Timeout
You can set how many seconds the printer waits before ending a
print job if more data is not received when using parallel interface
and USB. If data from another port often appears in the middle of
a print job, you should increase the timeout value.
10 seconds, 15 seconds, 20 seconds, 25 seconds, 60 seconds
Note
❒ Default: 15 seconds
154
Host Interface Menu
Menu
Network Setup
Description
Items Only appear in the Network Setup when the related options
are installed.
Reference
For more information about the "Network Setup", see "Configuring the Printer for the Network" in the Setup Guide.
❖ DHCP
You can set how the network interface board acquires TCP/IP
settings.
Note
❒ Default: On
❖ IP Address
You can set the IP Address.
Limitation
❒ When DHCP is On, its setting cannot be changed. If you
want to change the setting, make the setting for DHCP Off.
Consult the network administrator for information about
how to make the setting for the network.
6
Note
❒ Default: 011.022.033.044
❖ Subnet Mask
You can set the Subnet Mask.
Limitation
❒ When DHCP is On, its setting cannot be changed. If you
want to change the setting, make the setting for DHCP Off.
Consult the network administrator for information about
how to make the setting for the network.
Note
❒ Default: All zero
❖ Gateway Address
You can set the Gateway Address.
Limitation
❒ When DHCP is On, its setting cannot be changed. If you
want to change the setting, make the setting for DHCP Off.
Consult the network administrator for information about
how to make the setting for the network.
Note
❒ Default: All zero
155
Making Printer Settings with the Control Panel
Menu
Network Setup
Description
❖ Frame Type (NW)
You can set the Frame Type for NetWare.
Note
❒ Default: Auto
❖ Active Protocol
You can set the Active protocol.
TCP/IP, NetWare, NetBEUI, AppleTalk
Note
❒ Default: All Active
❖ Ethernet
You can select the speed of the network to which the printer is
connected.
Auto, 10 Mbps, 100Mbps
Note
❒ Default: Auto
❖ LAN Type
6
You can select Ethernet or IEEE 802.11b for the LAN Type.
Note
❒ Default: Ethernet
❒ Appears Only when the optional 802.11b Interface Unit is
installed in the Network standard model.
156
Host Interface Menu
Menu
IEEE 1394 Setup
Description
*1
You can make settings for using IEEE 1394. This menu appears
Only when the optional IEEE 1394 Interface Unit is installed.
Reference
For more information about the "IEEE 1394 Setup", see "Configuring the Printer for the Network" in the Setup Guide.
❖ DHCP
You can set the method the IEEE 1394 Interface Unit uses to acquire TCP/IP settings.
Note
❒ Default: On
❖ IP Address1394
You can set the IP address for IEEE 1394 (IP over 1394).
Note
❒ Default: All zero
❖ Subnet Mask1394
You can set the Subnet Mask for IEEE 1394 (IP over 1394).
6
Note
❒ Default: All zero
❖ IP over 1394
You can activate IP over 1394.
Note
❒ Default: Active
❖ SCSI print
You can activate SCSI print.
Note
❒ Default: Active
❖ Bidi-SCSI print
You can activate bidirectional transmission for SCSI print.
Note
❒ Default: On
157
Making Printer Settings with the Control Panel
Menu
IEEE 802.11b
*2
Description
You can make settings for using the wireless LAN. This menu appears Only when the optional IEEE 802.11b board is installed.
Reference
For more information about the "IEEE 802.11b", see "Configuring the Printer for the Network" in the Setup Guide.
❖ Comm. Mode
You can set the transmission mode for IEEE 802.11b.
802.11b Ad hoc, Infrastructure, Ad hoc
Note
❒ Default: 802.11b Ad hoc
❖ Channel
The selectable channels are 1-11 (Inch version) and 1-13 (Metric version).
Note
❒ Default: 11
❖ Trans. Speed
6
You can set the transmission speed for IEEE 802.11b.
Auto, 11Mbps, 5.5Mbps, 2Mbps, 1Mbps
Note
❒ Default: Auto
❖ SSID
You can make settings for SSID in Infrastructure mode and
802.11 Ad hoc mode.
Limitation
❒ Select “¥” if you want to enter “/” in the SSID. Also, “¥” appears when printing the configuration page, read it as “/”.
Note
❒ Up to 32 ASCII characters in the range 0x20-0x7e can be
used. The SSID setting is case-sensitive.
❒ An SSID value is automatically set to the nearest access
point if the setting has not been made.
❒ If the setting has not been made for 802.11 Ad hoc mode,
the same value for Infrastructure mode or an “ASSID” value is automatically set.
158
Host Interface Menu
Menu
IEEE 802.11b
*2
Description
❖WEP Setting
You can set the code for IEEE 802.11b.
Note
❒ Default: Not Active
❒ You need to set the WEP code key from the network before
making this setting. Without the key, transmission cannot
be performed.
❒ Be sure to set the key before setting the code to "Active".
USB Setting *3
You can set the transmission speed for USB.
Note
❒ Default: Auto
Bluetooth *4
You can make settings for using Bluetooth. This menu appears
Only when the optional Bluetooth Interface Unit is installed.
Public, Private
Note
❒ Default: Public
*1
*2
*3
*4
6
Appears Only when the 1394 Interface Unit board is installed.
Appears Only when the 802.11b Interface Unit board is installed.
While the printer is Online, press {Enter #}
}, and then press {Escape}
}. Finally, press
{Menu}
} . You can access the "USB Setting" menu on the panel display.
While the printer is Online, press {Enter #}
}, and then press {Escape}
}. Finally, press
{Menu}
} . You can access the "Bluetooth" menu on the panel display.
159
Making Printer Settings with the Control Panel
Changing the Host Interface Menu
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the panel display.
B Press {U} or {T} to display the “Host Interface” menu.
Menu:
Host Interface
6
C Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
Host Interface:
I/O Buffer
D Press {U} or {T} to display “I/O Timeout”.
Host Interface:
I/O Timeout
160
Host Interface Menu
E Press {Enter #}}.
The following message appears on the panel display.
I/O Timeout:
*15 seconds
F Press {U} or {T} to select how many minutes the printer waits before ending a print job.
G Press {Enter #}}.
The screen returns to step D in a few seconds.
H Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
6
Data In
ZKEP010E
“Ready” appears on the panel display.
Ready
161
Making Printer Settings with the Control Panel
PCL Menu
There are 11 menu items in the “PCL Menu” .
• Orientation
• Form Lines
• Font Source
• Font Number
• Point Size
• Font Pitch
• Symbol Set
• Courier Font
• Ext. A4 Width
• Append CR to LF
• Resolution
PCL Parameters
6
Menu
Orientation
Description
You can set the page Orientation.
• Portrait
• Landscape
Note
❒ Default: Portrait
Form Lines
You can set the number of lines per page.
5-128
Note
❒ Default: 64 (Metric version), 60 (Inch version)
Font Source
You can set the location of the default font.
• Resident
• Internal
• Download
• HDD
Note
❒ Default: Resident
❒ When you select "Download", you can select Only fonts downloaded to printer RAM.
162
PCL Menu
Menu
Font Number
Description
You can set the ID of the default font you want to use.
• 0 to 50 (for Internal)
• 1 to downloaded number
Note
❒ Default: Internal
❒ Default: 0
Point Size
You can set the Point Size you want to use for the default font.
4 to 999.75 by 0.25
Note
❒ Default: 12.00
❒ This setting is effective Only for a variable-space font.
Font Pitch
You can set the number of characters per inch you want to use for
the default font.
0.44 to 99.99 by 0.01
Note
❒ Default: 10.00
6
❒ This setting is effective Only for a fixed-space font.
Symbol Set
You can specify the set of print characters for the default font. The
available options are as follows.
Roman-8, ISO L1, ISO L2, ISO L5, PC-8, PC-8 D/N, PC-850, PC852, PC8-TK, Win L1, Win L2, Win L5, Desktop, PS Text, VN Intl,
VN US, MS Publ, Math-8, PS Math, VN Math, Pifont, Legal, ISO 4,
ISO 6, ISO 11, ISO 15, ISO 17, ISO 21, ISO 60, ISO 69, Win 3.0
Note
❒ Default: Roman-8
Courier Font
You can select a courier font type.
• Regular
• Dark
Note
❒ Default: Regular
Ext. A4 Width
You can extend the width of the printable area for an A4 sheet
leaving a narrow margin on the sides.
Note
❒ Default: Off
163
Making Printer Settings with the Control Panel
Menu
Description
Append CR to LF
By adding a CR code to each LF code, you can print text data clearly.
• On
• Off
Note
❒ Default: Off
Resolution
You can set the print resolution in dots per inch.
• 300 dpi
• 600 dpi
Note
❒ Default: 600 dpi
Changing the PCL Menu
A Press {Menu}}.
6
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
"Menu" appears on the panel display.
B Press {U} or {T} to display "PCL Menu", and then press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
164
PCL Menu:
Orientation
PCL Menu
C Press {Enter #}}.
Orientation:
*Portrait
D Press {U} or {T} to select the Orientation desired, and then press {Enter #}}.
Wait for a few seconds.
The screen returns to step B in a few seconds.
E Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
6
ZKEP010E
"Ready" appears on the panel display.
Ready
165
Making Printer Settings with the Control Panel
PS Menu
There are two menu items in the “PS Menu” .
• Data Format
• Resolution
PS Parameters
Menu
Data Format
Description
You can select the data format.
• Binary Data
• TBCP
Limitation
❒ This setting is effective when operating the machine with a
parallel, USB or EtherTalk connection.
❒ When operating the machine with a parallel or USB connection, if binary data is sent from the printer driver, the print job
is canceled.
6
❒ When operating the machine with an Ethernet connection, the
print job is canceled under the following conditions;
• The printer driver data format is TBCP and the data format
selected on the control panel is Binary Data.
• The printer driver data format is binary and the data format selected on the control panel is TBCP.
Note
❒ Default: Binary Data
Resolution
You can select the resolution.
• 300 dpi
• 600 dpi
• 1200 dpi
Note
❒ Default: 600 dpi
166
PS Menu
Changing the PS Menu
The following example describes how to change the setting for “TBCP”:
A Press the {Menu}} key.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
“Menu” appears on the display.
B Press the {U} or {T} key to display “PS Menu”, and then press the {Enter #}}
key.
On Line
6
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the display:
PS Menu:
Data Format
C Press the {Enter #}} key.
Data Format:
*Binary Data
D Press the {U} or {T} key to select the TBCP desired, and then press the {Enter #}
} key. Wait for two seconds.
“PS Menu” appears on the display.
167
Making Printer Settings with the Control Panel
E Press the {On Line}} key.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
“Ready” appears on the display.
Ready
6
168
PDF Menu
PDF Menu
There are two menu items in the “PDF Menu” .
• PDF: Change PW
• Resolution
PDF Parameters
Menu
Description
PDF: Change PW
Set [Password to Open the Text File] for the PDF file executing PDF
Direct Print.
• PDF Current PW
• Enter new PW
Important
❒ A password can be set using on the Web Image Monitor, but
in this case the password information is sent through the network. If security is a priority, set the password using this menu
from the Control Panel.
6
Note
❒ Default: no password set.
Resolution
You can select the resolution.
• 300dpi
• 600dpi
• 1200dpi
Note
❒ Default: 600dpi
Changing the PDF Menu
A Press {Menu}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
"Menu" appears on the panel display.
169
Making Printer Settings with the Control Panel
B Press {U} or {T} to display "PDF Menu", and then press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
PDF Menu:
PDF: Change PW
C Press {U} or {T} to display "Resolution", and then press {Enter #}}.
On Line
6
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
The following message appears on the panel display.
PDF Menu:
Resolution
D Press {Enter #}}.
Resolution:
*600dpi
E Press {U} or {T} to select the resolution desired, and then press {Enter #}}.
Wait for a few seconds.
The screen returns to step B in a few seconds.
170
PDF Menu
F Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP010E
"Ready" appears on the panel display.
Ready
6
171
Making Printer Settings with the Control Panel
Language Menu
You can select the language you use. Available language as are follows:
English, French, German, Italian, Spanish, Dutch, Swedish, Norwegian, Danish,
Finnish, Portuguese, Czech, Polish, Hungarian
Note
❒ Default: English
Changing the Language Menu
You can change the language by the following procedures below.
A Press {Menu}}.
On Line
6
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP020E
”Menu” appears on the panel display.
B Press {U} or {T} to display “Language” menu.
Menu:
Language
C Press {Enter #}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
Data In
ZKEP060E
172
Language Menu
The following message appears on the panel display.
Language:
*English
D Press {U} or {T} until the language you want to select appears on the panel
display.
E Press {Enter #}}. Wait for a few seconds.
The screen returns to step B in a few seconds.
F Press {On Line}}.
On Line
Menu
Job Reset
Escape
Form Feed
Enter
Power
Error
6
Data In
ZKEP010E
"Ready" appears on the panel display.
Ready
173
Making Printer Settings with the Control Panel
6
174
7. Appendix
Replacing Parts
The Maintenance Kit contains parts necessary for maintaining the printer. When
“Replace Maintenance Kit” appears on the panel display, install the replacement parts included in the Maintenance Kit.
R WARNING:
• It is dangerous to handle the plug with wet hands. An electric shock
might occur.
R CAUTION:
• The inside of the machine could be very hot. Do not touch the parts with a
label indicating "v" (means hot surface). Touching "v" (means hot surface) could result in a burn.
• When you pull the plug out of the socket, grip the plug to avoid damaging
the cord and causing a fire or an electric shock.
• Be sure to turn off the printer and wait for about an hour before replacing
parts. Not waiting for the printer to cool down can result in a burn.
Note
❒ If you dispose of the used parts yourself, dispose of them according to local
regulations.
MAINTENANCE KIT Type 400
Checking the contents of the box
Check the contents of the box according to the following list. If one or more items
are missing, contact your sales or service representative.
Description
Friction pad
Quantity
3 pcs
Paper feed roller 3 pcs
See p.177 “Replacing the Friction Pad”.
See p.178 “Replacing the Paper Feed Rollers”.
175
Appendix
Description
Quantity
Transfer roller
1 pc
Gloves
1 pair
Fusing Unit
1 pc
See p.179 “Replacing the
Transfer Roller”.
See p.182 “Replacing the Fusing Unit”.
Preparing to replace the parts
You should replace all the parts included in Maintenance Kit at the same time.
Be sure to replace them in the following order:
A Check the contents of the box for the following items:
•
•
•
•
•
7
Friction pad
Paper feed roller
Transfer roller
Fusing Unit
Gloves
B Confirm that the followings are true:
• The power switch is turned off.
• The power cord is unplugged from the wall outlet.
• The interface cable is unplugged from the printer.
Important
❒ Wait about an hour after the printer is turned off to allow internal parts to
cool down before replacing the Maintenance Kit.
176
Replacing Parts
D Use a sharp-pointed item
Replacing the Friction Pad
Replace all the friction pads in the
tray. The following procedure shows
how to replace the paper tray's friction pad (Tray 1).
A Pull
out the paper tray until it
stops.
like a
ball-point pen, to release the two
catches that lock the friction pad.
Note
❒ The friction pad may fall off
when the catches are released.
Place your hand over the friction pad while releasing the
catches.
❒ The friction pad spring may
come off. Be careful the spring
does not fall off and become
lost.
ZKDX270J
B While lifting the front side of the
tray, pull it out of the printer.
7
ZKEM170E
E Return the paper tray to its origi-
nal position, and remove the friction pad from the tray.
ZKEY140E
C Remove
paper from the paper
tray. Place the tray upside down
on a flat surface.
Note
❒ The friction pad spring may
come off. Be careful the spring
does not fall off and become
lost.
ZKDM180J
ZKDM160J
177
Appendix
F Insert the new friction pad in the
paper tray.
Attach the center projection of the
new friction pad to the spring and
align the projection of both sides of
the friction pad to the holes of the
paper tray. Then push the friction
pad as shown in the illustration
until it clicks.
Replacing the Paper Feed
Rollers
Replace all feed rollers including the
printer and the optional Paper Feed
Unit(s). The following procedure
shows how to replacing the paper
feed rollers of the printer.
R CAUTION:
• When lifting the machine, use
the inset grips on both sides.
Otherwise the printer could
break or cause injury if dropped.
A Remove the optional Duplex Unit
from the printer if it is installed.
ZKDM190J
After pushing in the friction pad,
try pushing it several times to
check it is properly installed. If it
jumps back into position due to the
force of the spring, it is properly installed.
7
Reference
See “Moving and Transporting
the Printer” in the Printer Reference on the CD-ROM labeled
"Operating Instructions".
B Move the printer to the edge of a
sturdy and stable table or desk.
G If your printer is equipped with
the optional Paper Feed Unit(s),
follow the same procedure when
replacing the friction pad.
ZKEM110E
Important
❒ Be sure to move the printer horizontally. Moving the printer
facing up on down may cause
the toner to scatter.
❒ Do not put the printer on an unstable or tilted surface.
178
Replacing Parts
Note
❒ If the printer is equipped with
the optional Paper Feed Unit,
do not move the printer and the
unit together, they are not securely attached.
C Slide the green lock lever to the
right (A
A), remove the paper feed
roller (B
B).
The illustration shows an example
of the paper feed roller as installed
in the printer.
E If the printer is equipped with the
optional Paper Feed Unit(s), follow the same procedure when replacing the paper feed roller.
If you installed two Paper Feed
Units, also replace both paper feed
rollers.
F Place paper in the paper trays and
additional removed paper trays.
Lift the front of the tray, and slide
it carefully into the printer until it
stops.
ZKEM120E
D While sliding the green lock lever
to the right (A
A), set the new roller
(B
B ). After that, return the green
lock lever to its original position
(C
C).
ZKDY150J
7
Replacing the Transfer Roller
A While
holding the front cover
with both hands on the left and
right sides, press the release button to open it.
ZKEM130E
Note
❒ Confirm that the green lock lever secures the roller correctly
by checking if the new roller rotates smoothly.
ZKEH120E
179
Appendix
B Pull the toner cartridge out of the
printer, while lifting the front
side.
Note
❒ Be sure to place the used cartridge on the level place.
E Hold the green parts of the roller
on both sides, and remove the
roller from the printer as shown
in the illustration.
ZKEM210E
F Insert the new transfer roller on
ZKET110E
C To
the socket with the gear of the
roller positioned on the left.
avoid making your hands
dirty with toner from the transfer
roller, wear the gloves included
in the Maintenance Kit.
$” parts),
D Hold the lock levers (“$
7
and pull them.
ZKDM220J
Important
❒ Do not insert the roller on the
back of the socket, or the printer
might be damaged.
ZKDM200J
180
❒ Insert the metallic part of the
roller on the socket. If you insert
the sponge part of the roller, the
roller might be damaged.
Replacing Parts
G Push
down the green parts of
both sides of the printer until it
clicks as shown in the illustration.
I Lower the toner cartridge when it
touches the back.
ZKET140E
ZKEM221E
Note
❒ When the transfer roller is set,
the transfer roller cover will return to its original position automatically.
J Close the front cover by pressing
the left and right side indentations.
H Holding the grips of the toner car-
tridge, insert it into the printer
until it stops.
7
ZKEH130E
K Take
the gloves off and go to
p.182 “Replacing the Fusing
Unit”.
ZKET120E
181
Appendix
B Lift the lock levers of the fusing
Replacing the Fusing Unit
unit as shown in the illustration.
R CAUTION:
• The fusing unit becomes very
hot. When installing the new fusing unit, turn off the printer and
wait about an hour. After that, install the new fusing unit. Not
waiting for the unit to cool down
can result in a burn.
A If the rear cover is attached to the
printer, remove it.
Note
❒ Proceed to step B if the optional
Duplex Unit was removed in
step A , "Replacing the Paper
Feed Rollers".
A Place a finger in the printer's
rear cover finger hole (upper
center) and pull it open.
ZKEX222E
C Pull the fusing unit out.
7
ZKEX223E
D Pull out the pins on both sides of
the new fusing unit.
ZKDX210J
B Remove the rear cover in a horizontal direction.
ZKDM010J
ZKDX220J
182
Replacing Parts
E Replace the new fusing unit into
the printer.
A Insert the rear cover to the inside grooves on both sides of
the printer in a horizontal direction.
ZKEX224E
F Push the lock levers of the fusing
unit down until it clicks.
ZKEX221E
B Close the rear cover.
Proceed to stepI.
7
ZKEX225E
G Reinstall the rear cover removed
in step A.
Note
❒ Proceed to step H if the optional
Duplex Unit was removed in
step A , "Replacing the Paper
Feed Rollers".
ZKEX211E
H Reinstall
the optional Duplex
Unit if it was removed in step A,
"Replacing the Paper Feed Rollers".
Reference
See p.189 “Moving and Transporting the Printer”.
I Print a configuration page to confirm that the printer works properly.
Reference
For more information about
printing the configuration page,
s e e p .1 28 “ L i s t /T e s t P ri n t
Menu”.
183
Appendix
Collate
Reference
For more information about collate, see the printer driver's Help file.
❖ Collate
Outputs can be assembled as sets in sequential order.
1
2
3
1
2
3
1
2
3
1
2
3
Limitation
❒ You must install an additional Memory Unit or the optional hard disk drive
to use the collatte function.
❒ The numbers of pages that can be collated after installing an additional Memory Unit are indicated below.
7
Total Memory Size
Approximate Number of Pages *1
128 MB (additional of 64 MB)
200 pages
192 MB (additional of 128 MB)
1,000 pages
320 MB (additional of 256 MB)
*1
Based on A4K, 5% chart and 600 dpi. Page numbers vary according to resolution
and data.
❒ When the optional hard disk drive installed, maximum number of pages that
can be collated is about 1,000, including Sample Print and Locked Print pages.
184
Spool Printing
Spool Printing
With Spool Printing, the whole data of a print job is saved in the Printer Hard
Disk before printing. To use this function, set it from the menu. See p.146 “System Menu”.
Important
❒ Do not turn off the printer or the computer when a print job is being spooled
and the Data In indicator is blinking. If you do, the print job will remain in
the Printer Hard Disk and be printed when the printer is turned on.
Limitation
❒ Spool Printing does not appear unless the optional Hard Disk Drive is installed.
❒ Data that has been received in the protocol other than LPD or IPP cannot be
spooled.
❒ Up to 50 jobs (approximately 500 MB) can be spooled at a time.
❒ When Spool Printing is on, the size of a single print job cannot exceed 500 MB.
❒ When sending spooled print jobs from more than one computer at the same
time, up to five LPR jobs and one IPP job can be spooled. Jobs exceeding the
maximum number cannot be spooled. Wait until the number of spooled print
jobs falls below the maximum.
7
Note
❒ When "On" is selected, the first print will take time.
❖ Confirm or delete the spooled job from a Web browser.
The spooled job can be seen or deleted from a Web browser. Start a Web
browser, and then input the IP address of the printer for URL to show the top
page. Click [Admin Info.], and then click [Spool Printing]. Select the file, check for
delete, input the password, and then click the delete button. (The default
password is "password".)
185
Appendix
Precautions when using Windows Server
2003
Precautions when using the Terminal Server mode
Certain printer driver functions are disabled. Disabled functions are displayed
in gray. When using all printer driver functions, use Windows Server 2003 in
normal mode.
7
186
Memory Capacity and Paper Size
Memory Capacity and Paper Size
The following tables show the typical memory requirements of the RPCS printer
language. Memory requirements depend on your print data and printing environment, such as the "Memory Priority" setting or total memory size that the printer has
available. The print mode also effects whether the print job will equally completed.
Setting of the “Frame Priority”
Paper Size
Resolution (dpi)
Memory
Capacity
300 x 300
600 x 600
1,200 x 1,200
64MB
❍
❍
❍
128MB
❍
❍
❍
192MB
❍
❍
❍
320MB
❍
❍
❍
64MB
❍
❍
❍
128MB
❍
❍
❍
192MB
❍
❍
❍
320MB
❍
❍
❍
64MB
❍
❍
❍
A4
128MB
❍
❍
❍
Letter (8 1/2x11)
192MB
❍
❍
❍
320MB
❍
❍
❍
64MB
❍
❍
❍
128MB
❍
❍
❍
192MB
❍
❍
❍
320MB
❍
❍
❍
64MB
$
$
$*
128MB
$
$
$
192MB
$
$
$
320MB
$
$
$
64MB
❍
❍
❍
16K
128MB
❍
❍
❍
(195x267mm)
192MB
❍
❍
❍
320MB
❍
❍
❍
A5
B5
Legal (81/2x14)
Maximum
custom size
(216 x 432 mm)
❍
Means that the print job is supported by simplex and Duplex printing.
$
Means the print job is supported only by simplex printing.
$*
Means it might be impossible to print images complex data with printing. Even
with simple data, the number of pages printed with printing might be limited. 187
7
Appendix
Setting of the “Font Priority”
Paper Size
A5
B5
Capacity
300 x 300
600 x 600
1,200 x 1,200
64MB
❍
❍
❍
128MB
❍
❍
❍
192MB
❍
❍
❍
320MB
❍
❍
❍
64MB
❍
❍
❍
128MB
❍
❍
❍
192MB
❍
❍
❍
320MB
❍
❍
❍
64MB
❍
❍
❍*
A4
128MB
❍
❍
❍
Letter (8 1/2x11)
192MB
❍
❍
❍
320MB
❍
❍
❍
64MB
❍
❍
❍*
128MB
❍
❍
❍
192MB
❍
❍
❍
320MB
❍
❍
❍
Legal (81/2x14)
7
Resolution (dpi)
Memory
Maximum custom size (216 x
432 mm)
64MB
$
$
$*
128MB
$
$
$
192MB
$
$
$
320MB
$
$
$
64MB
❍
❍
❍
16K
128MB
❍
❍
❍
(195x267mm)
192MB
❍
❍
❍
320MB
❍
❍
❍
❍
Means that the print job is supported by simplex and Duplex printing.
❍*
Means it might be impossible to print images complex data with Duplex printing. Even with simple date, the number of pages printed with Duplex printing
might be limited.
$
Means the print job is supported only by simplex printing.
$*
Means it might be impossible to print images complex data with printing. Even
with simple data, the number of pages printed with printing might be limited.
188
Moving and Transporting the Printer
Moving and Transporting the Printer
R CAUTION:
• When lifting the machine, use
the inset grips on both sides.
Otherwise the printer could
break or cause injury if dropped.
• When you move the printer, remember to unplug the power
cord from the wall outlet to avoid
a fire or an electric shock.
• When you pull out the plug from
the socket, grip the plug to avoid
damaging the cord and causing
a fire or an electric shock.
Repack the printer in its original
packing materials for transporting.
Important
❒ Be sure to disconnect all cables
from the printer before transporting it.
Moving the printer in the short distance
A Confirm
that the followings are
true:
• The power switch is turned off.
• The power cord is unplugged
from the wall outlet.
• The interface cable is unplugged from the printer.
B If you installed external options,
remove them.
Removing the Duplex Unit
A Push down the lever on right
side of the Duplex Unit (A
A)
and pull it out until it stops
(B
B).
7
❒ The printer is a precision piece of
machinery. Take care to avoid
damage during shipment.
Moving the Printer
R CAUTION:
• The machine weight is approximately 17 kg (37.5 lb. bond).
• When lifting the machine, use
the inset grips on both sides.
Otherwise the printer could
break or cause injury if dropped.
ZKEX660E
B Push the under board levers
(A
A) and pull the Duplex Unit
out of the printer (B
B).
• Before moving the machine, unplug the power cord from the outlet. If the cord is unplugged
abruptly, it could become damaged. Damaged plugs or cords
can cause an electrical or fire
hazard.
ZKEY450E
189
Appendix
C Be sure to close the Bypass Tray
and the front cover.
D Lift the printer and move it to the
place where you want to install it.
R CAUTION:
• When lifting the machine, use
the inset grips on both sides.
Otherwise the printer could
break or cause injury if dropped.
ZKEH221E
7
Important
❒ Be sure to move the printer horizontally. Moving the printer facing
up on down may cause the toner to
scatter.
❒ If the Paper Feed Unit(s) is installed, detach and move the printer separately. Never move the
printer with the Paper Feed Unit(s)
attached.
190
Specifications
Specifications
Mainframe
❖ Configuration:
Desktop
❖ Print Process:
Laser beam scanning & Electrophotographic printing
Dual component toner development
❖ Printing Speed:
• Basic model
• Network standard model
Maximum 26 pages per minute (A4K, 81/2 × 11K)
Note
❒ Continuous printing on sheets with a width of 170 mm or smaller may decrease the printing speed depending on the temperature control of the fusing unit.
❖ Interface:
Standard 36–pin printer cable and a parallel port on the host computer
IEEE 1284 I/F (Compatible, ECP, Nibble)
• Do not use a cable more than 2.5 meters (8.2 feet) long.
• USB2.0
• Bidirectional IEEE1284
• 10/100Base-TX(std.for AP400N)
7
❖ Resolution:
1,200 × 1,200 dpi (PCL 6, RPCS, PS, PDF)
600 × 600 dpi (PCL 6, PCL 5e, RPCS, PS, PDF)
300 × 300 dpi (PCL 5e, PDF)
❖ Printer Language:
PCL 6 (XL) , PCL 5e, RPCS, Adobe PostScript 3
❖ Fonts:
PCL 6, PCL 5e
Agfa Font Manager 35 Intellifonts, 10 TrueType fonts, and 1 bitmap font
Font Manager available, plus 31 additional fonts.
PostScript, PDF
136 fonts(Type 2:24, Type 14:112)
❖ Paper size:
See p.35 “Paper and Other Media Supported by This Printer”
191
Appendix
❖ Paper Weight:
See p.35 “Paper and Other Media Supported by This Printer”
❖ Power Source:
120 V, 60 Hz, 7.4 A or more
❖ Power Consumption:
Maximum
820 W or less
Printing
760 W or less
Energy Saver
7.5 W or less
❖ Noise Emission *1 :
Sound Power Level
Mainframe Only
During Printing
63 dB (A)
Stand-by
39 dB (A)
Sound Pressure level *2
Mainframe Only
During Printing
*1
*2
7
53 dB (A)
The following measurements are actual values made in accordance with ISO7779.
Measured at the position of a bystander.
❖ Dimensions: *1
Width
Depth
Height
Printer Only
(tray not extended)
388 mm (14.9 inches) 450 mm (17.7 inches) 345 mm (13.6 inches)
Printer Only
(tray extended)
388 mm (14.9 inches) 508 mm (20.0 inches) 345 mm (13.6 inches)
With one optional
feed unit
388 mm (14.9 inches) 450 mm (17.7 inches) 479.5mm (18.9 inches)
With two optional
feed units
388 mm (14.9 inches) 450 mm (17.7 inches) 614 mm (24.1 inches)
*1
Measurement conditions: With paper tray and Bypass Tray extension closed.
❖ Weight:
Approximately 17 kg (37.5 lb. bond) (toner cartridge and power cord included)
❖ Warm-up Time:
Less than 12 seconds (23°C, 73F)
192
Specifications
❖ Paper Capacity:
Standard paper tray
500 sheets *1 (80g/m2, 20 lb.bond)
Bypass Tray *2
100 sheets *1 (80g/m2, 20 lb.bond)
Optional Paper Feed Unit × 2
500 sheets × 2 *1 (80g/m2, 20 lb.bond)
Optional Envelope Feeder *3
60 envelopes *4
*1
*2
*3
*4
Paper weight: 60 – 105 g/m2 (16 – 28 lb. bond)
You can load up to 10 envelopes (55 – 157 g/m2, 14 – 42 lb. bond) at the same time.
To use the Envelope Feeder Unit, the optional Paper Feed Unit is required. The
paper tray of the feed unit can be replaced with the Envelope Feeder Unit.
For more information about envelopes, see p.42 “Types of Paper and Other Media”.
❖ Paper Output Capacity:
250 sheets (80 g/m2, 20 lb. bond)
❖ Memory:
Standard 64MB, up to 320MB (with the optional Memory Unit)
❖ Network (Basic model printer requires the optional Network Interface Board):
Topology: Ethernet (10BaseT/100BaseTX)
Protocol: TCP/IP, NetBEUI, IPX/SPX, AppleTalk
❖ Optional Equipment:
Common for the Basic model printer and the Network standard model
printer
• Paper Feed Unit Type 400
• Envelope Feeder Type 400
• AD450 (Duplex Unit)
• Memory Unit Type C 64MB
• Memory Unit Type C 128MB
• Memory Unit Type C 256MB
• Hard Disk Drive Type 2600
• 1394 Interface Unit Type 4510
• 802.11b Interface Unit Type A
• Bluetooth Interface Unit Type 2045
Unique for the Basic model printer
• Network Interface Board Type 2610
7
193
Appendix
Options
Paper Feed Unit Type 400
❖ Dimensions (W×
×D×
×H):
388 × 496 × 135 mm (15.3 × 17.9 × 5.3 inches)
(without pins on the unit)
❖ Paper Weight:
60 – 105 g/m2 (16 – 28 lb. bond)
❖ Paper Size:
See p.35 “Paper and Other Media Supported by This Printer”.
Envelope Feeder Type 400
❖ Dimensions (W×
×D×
×H):
388 × 440 × 96 mm (15.3 × 15.9 × 3.8 inches)
❖ Paper Weight:
72 – 90 g/m2 (19 – 24 lb. bond)
7
❖ Paper Size:
See p.35 “Paper and Other Media Supported by This Printer”.
AD450 (Duplex Unit)
❖ Dimensions (W×
×D×
×H):
340 × 380 × 250 mm (13.4 × 15.0 × 7.7 inches)
❖ Paper Size:
See p.35 “Paper and Other Media Supported by This Printer”.
❖ Paper Weight:
60 – 105 g/m2 (17 – 28 lb. bond)
❖ Weight:
5 kg (11.0 lb. bond)
Hard Disk Drive Type 2600
194
❖ Storage Capacity (Formatted):
6 GB
You can install PostScript fonts with this optional Hard Disk Drive. With a
Macintosh, types of fonts supported are PostScript Type 1 and PostScript
Type 2. To download them, use PS Utility for Mac.
Specifications
Memory Unit Type C (64MB/128MB/256MB)
❖ Module Type:
SO-DIMM (Small Outline Dual-in-line Memory Module)
❖ Memory Type:
SDRAM (Synchronous Dynamic RAM)
❖ Number of Pins:
144 pins
Network Interface Board Type 2610
❖ Topology:
Ethernet (10BaseT/100BaseTX)
❖ Protocols:
TCP/IP, NetBEUI, IPX/SPX, AppleTalk
❖ Interface Connector:
RJ45
❖ Required Cable:
STP (Shielded Twisted-Pair) cable
Category / Type5 or better
7
1394 Interface Unit Type 4510
❖ Transmission Spec.:
IEEE 1394
❖ Device Class:
SCSI print, IP over 1394
❖ Interface Connector:
IEEE 1394 (6 pins × 2)
❖ Required cable:
1394 interface cable (6 pins x 4 pins, 6 pins x 6 pins)
Important
❒ You cannot plug devices together to create loops.
❒ Do not use a cable more than 4.5 meters (14.8 feet) long.
❖ Connectable number of device in a bus:
Maximum 63
195
Appendix
❖ Allowed cable hops in a bus:
Maximum 16
❖ Power supply:
Nonpower supply
Cable Power repeated (IEEE 1394a-2000 compliant)
802.11b Interface Unit TypeA (R-WL11)
❖ Transmission Spec.:
Based on IEEE 802.11b (Wireless LAN)
❖ Protocol:
TCP/IP, NetBEUI, IPX/SPX, AppleTalk
Note
❒ SmartNetMonitor and Web Image Monitor are supported.
❖ Data Transfer Speed:
Auto select from below speed
1Mbps, 2Mbps, 5.5Mbps, 11Mbps
❖ Frequency Range:
• Inch version:
2412-2464 Mhz (1-11 channels)
• Metric version:
2412-2472 Mhz (1-13 channels)
7
❖ Transmittable Distance:
1Mbps 400m *1
2Mbps 270m *1
5.5Mbps 200m *1
11Mbps 140m *1
*1
These figures are a guideline for outdoor use. In general, the transmittable distance indoors is 10-100 m, depending on the environment.
❖ Transmission Mode:
ad hoc mode and infrastructure mode
196
Specifications
Bluetooth Interface Unit Type 2045
❖ Supported Profiles:
SPP (Serial Port Profile)
HCRP (Hardcopy Cable Replacement Profile)
BIP (Basic Imaging Profile)
❖ Frequency Range:
2GHz ISM band
❖ Data Transmission Speed:
732 kbps
Note
❒ The transmission speed is adjusted according to factors such as the distance and obstacles between the devices, radio signal condition and BluetoothTM adaptor.
❖ Maximum Range:
10m
7
197
Appendix
Consumables
R CAUTION:
• Our products are engineered to meet the highest standards of quality and
functionality. When purchasing expendable supplies, we recommend using
Only those specified by an authorized dealer.
❖ Toner Cartridge
Printable number of pages per cartridge *1
Toner Cartridge
*1
25,000 pages
A4, 3% test chart
Note
❒ The actual number of printed pages you get from a particular toner cartridge depends on the type and size of paper you are using, the contents of
your print images, and printing environment conditions. All this means
that a toner cartridge might require replacement sooner than the normal
life described above.
❒ The number of printable pages that can be expected from the starter toner
cartridge included in the printer is about 10,000 pages (A4, 3% chart).
❖ Maintenance Kit
MAINTENANCE KIT Type 400
It is required to change the Maintenance Kit after every 90,000 pages have
been printed. However, it may be necessary to change the parts earlier depending on their operating period.
7
198
Information about Installed Software
Information about Installed Software
expat
Expat(Version 1.1). Copyright 1998, 1999 James Clark. All rights reserved.
• The software installed on this product includes the expat application software Version 1.1 (hereinafter "expat 1.1").
• The product manufacturer has not made any modification to the source code
of the expat 1.1.
• The product manufacturer provides warranty and support to the software of
the product including the expat 1.1 and the product manufacturer makes Mr.
James Clark, the initial developer of the expat 1.1, free from these obligations.
• The expat 1.1 is made available under Mozilla Public License Version 1.1
(hereinafter "MPL 1.1"), and controller software of the product equals the
Larger Work as defined in MPL 1.1. The software of this product except the
expat 1.1 is licensed to the product manufacturer under separate agreement(s).
• The source code of the expat 1.1 is available at:
ftp://ftp.jclark.com/pub/xml/expat1_1.zip
• MPL 1.1 is also available at:
http://www.mozilla.org/MPL/MPL-1.1.html
• Information relating to the expat 1.1 is available at:
http://www.jclark.com/xml/expat.html
7
JPEG LIBRARY
• The software installed on this product is based in part on the work of the Independent JPEG Group.
199
Appendix
NetBSD
Copyright Notice of NetBSD
For all users to use this product:
This product contains NetBSD operating system:
For the most part, the software constituting the NetBSD operating system is not
in the public domain; its authors retain their copyright.
The following text shows the copyright notice used for many of the NetBSD
source code. For exact copyright notice applicable for each of the files/binaries,
the source code tree must be consulted.
A full source code can be found at http://www.netbsd.org/.
Copyright © 1999, 2000 The NetBSD Foundation, Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
A Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
B Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
C All advertising materials mentioning features or use of this software must
display the following acknowledgment:
This product includes software developed by the NetBSD Foundation, Inc.
and its contributors.
D Neither the name of The NetBSD Foundation nor the names of its contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND
CONTRIBUTORS ''AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
7
200
Information about Installed Software
Authors Name List
All product names mentioned herein are trademarks of their respective owners.
The following notices are required to satisfy the license terms of the software
that we have mentioned in this document:
• This product includes software developed by the University of California,
Berkeley and its contributors.
• This product includes software developed by Jonathan R. Stone for the NetBSD Project.
• This product includes software developed by the NetBSD Foundation, Inc.
and its contributors.
• This product includes software developed by Manuel Bouyer.
• This product includes software developed by Charles Hannum.
• This product includes software developed by Charles M. Hannum.
• This product includes software developed by Christopher G. Demetriou.
• This product includes software developed by TooLs GmbH.
• This product includes software developed by Terrence R. Lambert.
• This product includes software developed by Adam Glass and Charles Hannum.
• This product includes software developed by Theo de Raadt.
• This product includes software developed by Jonathan Stone and Jason R.
Thorpe for the NetBSD Project.
• This product includes software developed by the University of California,
Lawrence Berkeley Laboratory and its contributors.
• This product includes software developed by Christos Zoulas.
• This product includes software developed by Christopher G. Demetriou for
the NetBSD Project.
• This product includes software developed by Paul Kranenburg.
• This product includes software developed by Adam Glass.
• This product includes software developed by Jonathan Stone.
• This product includes software developed by Jonathan Stone for the NetBSD
Project.
• This product includes software developed by Winning Strategies, Inc.
• This product includes software developed by Frank van der Linden for the
NetBSD Project.
• This product includes software developed for the NetBSD Project by Frank
van der Linden
• This product includes software developed for the NetBSD Project by Jason R.
Thorpe.
• The software was developed by the University of California, Berkeley.
• This product includes software developed by Chris Provenzano, the University of California, Berkeley, and contributors.
7
201
INDEX
F
Font Number, 162
Font Pitch, 162
fonts, 191
Font Source, 162
Form Lines, 162
friction pad, 177
friction pad, cleaning, 110
fusing unit, 182
1394 interface cable, 195
1394 Interface Unit Type 4510, 195
802.11b Interface Unit TypeA (R-WL11), 196
A
AD450, 194
adhesive Labels, 43
Adjusting the Image Density, 114
Adjusting the Registration, 116
Append CR to LF, 162
Auto Continue, 146
H
Hard Disk Drive Type 2600, 194
HDD Format, 134
Hex Dump, 128
Host Interface, 122, 154
B
Bluetooth, 154
Bluetooth Interface Unit Type 2045, 197
Bypass Size, 124
C
Collate, 184
Config. Page, 128, 130
Config.P/Er.log, 128
Control Panel Lock
Locking the Panel, 137
Copies, 146
Courier Font, 162
Curl Prevention, 134
D
Data In indicator, 90, 91
Def Print Lang., 146
Duplex, 146
E
Edge-Edge Print, 146
Edge Smoothing, 146
E-Mail Date, 146
Energy Saver, 146
Envelope Feeder Type 400, 194
envelopes, 43
envelopes, loading, 55
error, 73
Error indicator, 89
Error Log, 128
Escape key, 123
Ethernet cable, 195
Ext. A4 Width, 162
202
I
IEEE 1394 Setup, 154
IEEE 802.11b, 154
Image Density, 134
I/O Buffer, 154
I/O Timeout, 154
K
Key Repeat, 134
L
Language, 122, 172
Letterhead Mode, 146
List/Test Print, 122, 128
List/Test Print Parameters, 128
Locked Print, 66, 122
M
Macintosh
uninstall, PostScript, 34
Maintenance, 122, 134, 135
MAINTENANCE KIT Type 400, 175
media, 35
memory, 187, 193
Memory Overflow, 146
Memory Unit Type C
(64MB/128MB/256MB), 195
Memory Usage, 146
menu, accessing, 122
menu, changing, 172
Menu Chart, 119
Menu key, 122
Menu List, 128
Menu Protect, 134, 137
messages, 73
misfeed, 97
N
Network Interface Board, 193, 195
Network Printing Guide, 3
Network Setup, 154
NIB, 193
Nortify by E-Mail, 146
O
OHP transparencies, 43
On Line indicator, 89
On Line key, 89, 123
options, 193, 194
Orientation, 162
P
Page Size, 146
panel display, messages, 73
Panel Lock, 137
Panel Protect
Locking the Panel, 137
paper, 35
paper feed roller, 178
paper feed roller, cleaning, 111
Paper Feed Unit Type 400, 194
Paper Input, 122, 124
paper, loading, 47
paper, sizes, types, 35
Paper Type, 124
Parallel cable, 191
PCL, 162
PCL 5e
Windows 2000, uninstalling, 29
Windows 95/98/Me, uninstalling, 29
Windows NT 4.0, uninstalling, 30
Windows XP/Server 2003, uninstalling, 29
PCL 6
Windows 2000, uninstalling, 29
Windows 95/98/Me, uninstalling, 29
Windows NT 4.0, uninstalling, 30
Windows XP/Server 2003, uninstalling, 29
PCL Config.Page, 128
PCL Menu, 122
PDF Config.Page, 128
PDF Menu, 122
Plain Paper, 42
Point Size, 162
PostScript
Macintosh, uninstall, 34
Windows 2000, uninstalling, 33
Windows 95/98/Me, uninstalling, 33
Windows NT 4.0, uninstalling, 34
Windows XP/Server 2003, uninstalling, 33
Ppr.Size Errors, 134
Precautions when using the Terminal
Server mode
Windows Server 2003, 186
Precautions when using Windows Server 2003
Windows Server 2003, 186
Printer Reference, 3
Print Lang., 146
Prt. Err Report, 146
PS Font List, 128
PS Menu, 122
Q
Quick Installation Guide, 3
R
RAM Disk, 146
Registration, 134
Registration roller, cleaning, 113
Resolution, 162
RPCS
Windows 2000, uninstalling, 31
Windows 95/98/Me, uninstalling, 31
Windows NT 4.0, uninstalling, 32
Windows XP/Server 2003, uninstalling, 31
S
Sample Print, 61, 122
SDRAM, 193, 195
Setup Guide, 3
specifications, 191
Spool Printing, 146
Sub Paper Size, 146
Symbol Set, 162
System, 122, 146
203
T
toner cartridge, replacing, 107
Toner Saving, 146
transfer roller, 179
Tray Locking, 124
Tray Paper Size, 124
Tray Priority, 124
troubleshooting, 73
U
Unit of Measure, 146
USB Setting, 154
204
W
Windows 2000
PCL 5e, uninstalling, 29
PCL 6, uninstalling, 29
PostScript, uninstalling, 33
printer properties, PCL, 6
printer properties, PostScript, 19
printer properties, RPCS, 13
RPCS, uninstalling, 31
Windows 95/98/Me
PCL 5e, uninstalling, 29
PCL 6, uninstalling, 29
PostScript, uninstalling, 33
printer properties, PCL, 5
printer properties, PostScript, 18
printer properties, RPCS, 11
RPCS, uninstalling, 31
Windows 95/98/Me, Windows 2000,
Windows XP/Server 2003, Windows NT 4.0
canceling a job, 25
Windows NT 4.0
PCL 5e, uninstalling, 30
PCL 6, uninstalling, 30
PostScript, uninstalling, 34
printer properties, PCL, 9
printer properties, PostScript, 22
printer properties, RPCS, 16
RPCS, uninstalling, 32
Windows XP/Server 2003
PCL 5e, uninstalling, 29
PCL 6, uninstalling, 29
PostScript, uninstalling, 33
printer properties, PCL, 6
printer properties, PostScript, 19
printer properties, RPCS, 13
RPCS, uninstalling, 31
WL.LAN Defaults, 134
WL.LAN Signal, 134
EN
USA
G095-8636
Copyright © 2003
EN USA G095-8636