605
OWNERS MANUAL
for
INTEGRITY™
5-WARMER
COFFEE BREWERS
MODEL:
8752
8752KFT
Includes:
Installation
Operation
Use & Care
Servicing Instructions
Model 8752 Brewer
with optional
8900-Series Decanters
PRINTED IN UNITED STATES OF AMERICA
p/n 70988 Rev. B ECN-12887
M605
050617 cps
WARRANTY STATEMENT
It also does not apply if the serial nameplate has been
removed or unauthorized service personnel perform service.
The prices charged by Bloomfield Industries for its products
are based upon the limitations in this warranty. Seller’s
obligation under this warranty is limited to the repair of defects
without charge by a Bloomfield Industries Authorized Service
Agency or one of its sub-agencies. This service will be
provided on customer’s premises for non-portable models.
Portable models (a device with a cord and plug) must be
taken or shipped to the closest Authorized Service Agency,
transportation charges prepaid, for services.
All electrical equipment manufactured by BLOOMFIELD
INDUSTRIES is warranted against defects in materials and
workmanship for a period of one year from the date of original
installation or eighteen (18) months from the date of shipment
from our factory, whichever comes first, and is for the benefit
of the original purchaser, except that:
a. airpots carry a 30 day parts warranty only.
b. dispensers; i.e., tea and coffee carry a 90 days parts
warranty only, excludes decanters.
THE FOREGOING OBLIGATION IS EXPRESSLY GIVEN IN
LIEU OF ANY OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, WHICH ARE HEREBY EXCLUDED.
In addition to restrictions contained in this warranty, specific
limitations are shown below (Additional Warranty Exclusions).
Bloomfield Industries Authorized Service Agencies are located
in principal cities.
BLOOMFIELD INDUSTRIES DIVISION / SPECIALTY
EQUIPMENT MANUFACTURING CORPORATION SHALL
NOT BE LIABLE FOR INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES FROM ANY
CAUSE WHATSOEVER.
This warranty is valid in the United States and void elsewhere.
Please consult your classified telephone directory or your food
service equipment dealer; or, for information and other details
concerning warranty, write to:
Service Parts Department
Bloomfield Industries
P.O. Box 280
Verdi, NV 89439
Phone: (888) 492-2782
Fax: (888) 492-2783
This warranty is void if it is determined that upon inspection by
an Authorized Service Agency that the equipment has been
modified, misused, misapplied, improperly installed, or
damaged in transit or by fire, flood or act of God.
SERVICE POLICY AND PROCEDURE GUIDE
ADDITIONAL WARRANTY EXCLUSIONS
1.
2.
3.
4.
6.
SHIPPING DAMAGE CLAIMS PROCEDURE
NOTE: For your protection, please note that equipment in
this shipment was carefully inspected and packaged by
skilled personnel before leaving the factory.
Upon acceptance of this shipment, the transportation
company assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1. VISIBLE LOSS OR DAMAGE: Be certain that any
visible loss or damage is noted on the freight bill
or express receipt, and that the note of loss or damage
is signed by the delivery person.
2. FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3.
CONCEALED LOSS OR DAMAGE: if damage is
unnoticed until the merchandise is unpacked, notify the
transportation company or carrier immediately, and file
“CONCEALED DAMAGE” claim with them. This
must be done within fifteen (15) days from the date the
delivery was made to you. Be sure to retain the
container for inspection.
Bloomfield Industries cannot assume liability for damage or
loss incurred in transit. We will, however, at your request,
supply you with the necessary documents to support your
claim.
xi
605 70988 Owners Manual Integrity 5W Decanter Brewer
5.
7. Full use, care and maintenance instructions are supplied
with each machine. Those miscellaneous adjustments
noted are customer responsibility. Proper attention will
prolong the life of the machine.
8. Travel mileage is limited to sixty (60) miles from an
authorized Service Agency or one of its sub-agencies.
9. All labor shall be performed during normal working hours.
Overtime premium shall be charged to the customer.
10. All genuine Bloomfield replacement parts are warranted
for ninety (90) days from date of purchase on nonwarranted equipment.
Any use of non-genuine
Bloomfield parts completely voids any warranty.
11. Installation, labor and job check-out are not considered
warranty.
12. Charges incurred by delays, waiting time or operating
restrictions that hinder the service technicians ability
to perform services are not covered by warranty.
This includes institutional and correctional facilities.
Resetting of safety thermostats, circuit breakers,
overload protectors, or fuse replacements unless
warranted conditions are the cause.
All problems due to operation at voltages other than
specified on equipment nameplates; conversion to
correct voltage must be the customer’s responsibility.
All problems due to electrical connections not made in
accordance with electrical code requirements and
wiring diagrams supplied with the equipment.
Replacement of items subject to normal wear, to include
such items as knobs and light bulbs. Normal maintenance
functions including adjustment of thermostats, microswitches,
and replacement of fuses and indicating lights are not
covered under warranty.
All problems due to inadequate water supply, such as
fluctuating, or high or low water pressure.
All problems due to mineral/calcium deposits, or
contamination from chlorides/chlorines. De-liming is
considered a preventative maintenance function and is
not covered by warranty.
TABLE OF CONTENTS
WARRANTY STATEMENT
SPECIFICATIONS
FEATURES & OPERATING CONTROLS
PRECAUTIONS & GENERAL INFORMATION
AGENCY LISTING INFORMATION
INSTALLATION INSTRUCTIONS
OPERATION
BREWING COFFEE
CLEANING INSTRUCTIONS
TROUBLESHOOTING SUGGESTIONS
SERVICING INSTRUCTIONS
Deliming Instructions
EXPLODED VIEW & PARTS LIST
WIRING DIAGRAMS
xi
1
2
3
3
4
6
8
9
10
11
16
18
23
Thank You for purchasing this
Bloomfield Industries appliance.
Proper installation, professional
operation and consistent
maintenance of this appliance will
ensure that it gives you the very
best performance and a long,
economical service life.
This manual contains the
information needed to properly
install this appliance, and to use,
care for and maintain or repair the
appliance in a manner which will
ensure its optimum performance.
605 70988 Owners Manual Integrity 5W Decanter Brewer
SPECIFICATIONS
MODEL
STYLE
VOLTS
WATTS
AMPS
1ø
POWER SUPPLY
CORD
8752
8752KFT
Decanter Brewer
5 Warmers
115/230
4000
19.4
None provided
Wire directly to circuit
APPLICABILITY
This manual applies to the following Bloomfield Industries products:
Model 8752 Integrity 5-Warmer Coffee Brewer
Model 8752KFT 5-Warmer Coffee Brewer
1
FEATURES AND OPERATING CONTROLS
605 70988 Owners Manual Integrity 5W Decanter Brewer
Fig. 1 Model 8752 Features and Operating Controls
2
PRECAUTIONS AND GENERAL INFORMATION
WARNING: ELECTRIC SHOCK HAZARD
All servicing requiring access to non-insulated components must be performed by qualified
service personnel. Do not open any access panels which require the use of tools.
Failure to heed this warning can result in electrical shock.
WARNING: INJURY HAZARD
All installation procedures must be performed by qualified personnel with full knowledge of all
applicable electrical and plumbing codes. Failure could result in property damage and
personal injury.
WARNING: ELECTRIC SHOCK HAZARD
Brewer must be properly grounded to prevent possible shock hazard. DO NOT assume a
plumbing line will provide such a ground. Electrical shock will cause death or serious Injury.
WARNING: BURN HAZARD
This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from
contact with dispensed liquids.
This appliance is intended for commercial use only.
CAUTION:
This appliance is intended for use to brew beverage products for
human consumption. No other use is recommended or
authorized by the manufacturer or its agents.
ELECTRICAL DAMAGE
This appliance is intended for use in commercial establishments,
where all operators are familiar with the appliance use,
limitations and associated hazards. Operating instructions and
warnings must be read and understood by all operators and
users.
605 70988 Owners Manual Integrity 5W Decanter Brewer
Except as noted, this piece of equipment is made in the USA
and has American sizes on hardware. All metric conversions
are approximate and can vary in size.
The following trouble shooting, component views and parts lists
are included for general reference, and are intended for use by
qualified service personnel.
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and followed.
Damage to the Brewer will occur if
these instructions are not followed.
CAUTION:
BURN HAZARD
Exposed surfaces of the
appliance, brew chamber and
decanter may be HOT to the
touch, and can cause serious
burns.
This manual should be considered a permanent part of this
appliance. The manual must remain with the appliance if it is
sold or moved to another location.
AGENCY LISTING INFORMATION
This brewer is
and
listed under UL file E9253.
This brewer meets
Standard 4 only when installed,
operated and maintained in accordance with the enclosed
instructions.
E9253
E9253
STD 4
3
INSTALLATION
READ THIS CAREFULLY BEFORE STARTING THE INSTALLATION
IMPORTANT:
To enable the installer to make
a quality installation and to
minimize installation time, the
following suggestions and tests
should be done before the
actual unit installation is started:
CAUTION:
ELECTRICAL
DAMAGE
DO NOT plug in or energize this
appliance until all Installation
Instructions are read and
followed. Damage to the
Brewer will occur if these
instructions are not followed.
CAUTION:
UNSTABLE
EQUIPMENT HAZARD
Unpack the unit. Inspect all components for completeness and
condition. Ensure that all packing materials have been removed
from the unit.
Verify that the Spray Head Gasket and Spray Disk are properly
installed.
LEVELING THE UNIT
Verify that provided adjustable legs are installed at each corner of
the brewer.
Set Brewer in its operating location. Level the Brewer. A spirit
level should be placed on the top of the unit, at the edge, as a
guide when making level adjustments.
Level the unit from left to right and front to back by turning the
adjustable feet. Be sure all four feet touch the counter to prevent
tipping.
PLUMBER’S INSTALLATION INSTRUCTIONS
Brewer should be connected to a POTABLE WATER, COLD
WATER line. Flush water line before connecting to Brewer.
DO NOT use a saddle valve with a self-piercing tap for the water
line connection. Such a tap can become restricted by waterline
debris. For systems that must use a saddle tap, shut off the main
water supply and drill a 3/16” (minimum) tap for the saddle
connection, in order to insure an ample water supply. Remember
to flush the line prior to installing the saddle.
The brewer must be installed on a water line with average
pressure between 20 PSI and 90 PSI. If your water pressure
exceeds 90 PSI at anytime, a pressure regulator must be
installed in the water supply line to limit the pressure to not more
than 90 PSI in order to avoid damage to lines and solenoid.
NOTE: Water supply inlet line
must meet certain minimum
criteria to insure successful
operation of the brewer.
Bloomfield recommends 1/4"
copper tubing for installation of
less than 12 feet and 3/8" for
more than 12 feet from a 1/2"
water supply line.
4
605 70988 Owners Manual Integrity 5W Decanter Brewer
DO NOT operate brewer unless
factory supplied adjustable legs
are installed and properly
adjusted.
It is very important for safety
and for proper operation that the
brewer is level and stable when
standing in its final operating
position. Provided adjustable
legs must be installed at each
corner of the unit. Failure to
do so will result in movement of
the brewer which can cause
personal Injury and/or damage
to brewer.
REFER TO EXPLODED VIEWS FOR COMPONENT NAMES/
NUMBERS
INSTALLATION (continued)
A water shut-off valve should be installed on the incoming water
line in a convenient location (Use a low restriction type valve,
such as a 1/4-turn ball valve, to avoid loss of water flow thru the
valve.
NSF requires that the brewer be able to be moved for cleaning
underneath. A flex line or loops of copper tubing will satisfy this
requirement. See Figure 2 below.
NOTE: This equipment must be
installed to comply with
applicable federal, state and
local plumbing codes and
ordinances.
WARNING:
SHOCK HAZARD
Brewer must be properly
grounded to prevent possible
shock hazard. DO NOT
assume a plumbing line will
provide such a ground.
Electrical shock will cause death
or serious injury.
Fig. 2 Water Supply Installation
In some areas, local codes require a backflow preventer (check
valve) to be installed on the inlet water line. If a backflow
preventer is used, you must install a water hammer arrester in
the incoming line, between the backflow preventer and the
brewer inlet, as far away from the brewer as space will allow.
This will relieve the excessive back pressures that can cause
faucet leaks and solenoid malfunctions.
605 70988 Owners Manual Integrity 5W Decanter Brewer
ELECTRICIAN’S INSTALLATION INSTRUCTIONS
REFER TO ELECTRICAL SPECIFICATIONS - Page 1
Check the nameplate to determine correct electrical service
required for this installation.
IMPORTANT:
Supply power must match
nameplate for voltage and
phase. Connecting to the
wrong voltage will damage the
brewer or result in decreased
performance. Such damage is
not covered by warranty.
IMPORTANT:
Do not connect brewer to
electrical power until you are
ready to fill the tank. See
instructions on page 6.
IMPORTANT: Before connecting to electricity, make sure the
brewer is connected to the water supply.
IMPORTANT:
For power supply connections use COPPER WIRE only. Wiring
must be suitable for at least 75ºC. This brewer requires a
dedicated electric circuit.
Models 8752 must be wired by an electrician, and require a
115/230V 20A circuit (50/60 Hz, 2 hot legs / 1 neutral leg, plus
ground). Remove rear panel to gain access to terminal block.
Green terminal must be connected to a suitable building ground.
Circuit must be capable of 4000 Watts. See figure 3 at right.
IMPORTANT: Wiring must be installed in approved solid or
flexible conduit, and must be secured to the brewer with a strain
relief (to be provided by the installer).
5
Fig. 3 Electrical Installation
OPERATION
Fig. 4 Brewer Operation Diagram
START-UP
For initial start-up, or if the brewer has not been used for an
extended period of time:
♦ Be sure spray disk and brew gasket are properly installed in the
brew head.
♦ Be sure the water supply is properly connected and the water
supply valve is turned ON.
♦ Be sure the WATER TANK IS FILLED
BEFORE connecting brewer to electrical power THE WATER TANK
MUST BE FILLED. Place an empty decanter under the brew head.
Lift the pour-over cover then pour warm tap water into the pour-over
opening until water flows from the brew head. When water stops
dripping from the brew head, empty the container.
Once the tank is full of water, connect the brewer to electrical
power. Press the TANK HEATER SWITCH to “ON”. The heating
elements will begin heating the water in the tank. When the water
has reached the proper temperature, the READY TO BREW light
will glow.
6
605 70988 Owners Manual Integrity 5W Decanter Brewer
IMPORTANT:
Tank must be full of water
before pressing TANK
HEATER SWITCH "ON".
Heating elements will be
damaged if allowed to
operate without being
fully submerged in water.
Damage caused by
operating the brewer
without water in the tank
is NOT COVERED BY
WARRANTY.
OPERATION (continued)
Water temperature is sensed by a
thermobulb inserted into the water tank. This
temperature signal is fed to the thermostat,
which controls line power to the heating
element.
The setpoint temperature is adjustable at the
thermostat.
The element is protected from overtemperature by a hi-limit thermostat.
Fig. 5 Heat Control Diagram
WATER FLOW
POUR-OVER FEATURE
Pouring any amount of cold water into the
pour-over opening and into the basin pan
forces an identical amount of hot water out
of the tank and through the spray head into
the brew chamber.
AUTOMATIC OPERATION
605 70988 Owners Manual Integrity 5W Decanter Brewer
Pressing BREW button energizes the
solenoid valve, allowing water from an
external water supply to flow into the basin
pan and then into the hot water tank. This
forces an identical amount of hot water out
of the tank and through the spray head into
the brew chamber
The solenoid uses a flow control device so
that flow is consistent between 20 p.s.i. and
90 p.s.i.
Length of time the solenoid is open is
controlled by the timer.
HOT WATER FAUCET
The faucet water coil is submerged in the hot
water tank and draws heat from the brew
water. Water going to the water coil is not
controlled by the solenoid valve.
The faucet is at supply water pressure any
time the faucet shut-off valve is OPEN.
Fig. 6 Water Flow Diagram
7
BREWING COFFEE
CAUTION:
BURN HAZARD
Exposed surfaces of the
brewer, brew chamber and
decanter may be HOT to
the touch, and can cause
serious burns.
CAUTION:
BURN HAZARD
To avoid splashing or
overflowing hot liquids,
ALWAYS place an empty
decanter under the brew
chamber before starting
the brew cycle. Failure to
comply can cause serious
burns.
CAUTION:
BURN HAZARD
After a brew cycle, brew
chamber contents are
HOT. Remove the brew
chamber and dispose of
used grounds with care.
Failure to comply can
cause serious burns.
A. PREPARATION
Place one (1) genuine Bloomfield
paper filter in the brew chamber.
Add a pre-measured amount of
fresh coffee grounds.
Gently shake the brew chamber to
level the bed of grounds. Slide the
brew chamber into place under the
brew head.
Fig. 7 Brew Chamber
B. POUR-OVER OPERATION
NOTE: Any Integrity™ brewer can be used in the pour-over mode.
BE sure “READY TO BREW” light is lit.
Place the appropriate EMPTY decanter in place under the brew
chamber.
Fill a decanter with tap water. Lift the pour-over cover and pour the
entire contents of the decanter into the pour-over opening, which
will fill the basin.
Water from the basin will displace a like amount of heated water
from the tank. The hot water will be forced into the brew head
where it will spray over the bed of grounds. Freshly brewed coffee
will begin to fill the container under the brew chamber. When the
flow and all dripping stops, the coffee is ready to serve.
Discard the contents of the brew chamber. Rinse the brew
chamber in a sink. When the ”HEAT” light goes out, the brewer is
ready for another brew cycle.
C. AUTOMATIC OPERATION
BE sure “READY TO BREW” light is lit.
Press the “BREW” switch. The solenoid will open for an amount of
time determined by the timer setting, admitting a measured quantity
of water into the tank.
NOTE: Water for the hot
water faucet is heated in a
coil inside of the water
tank. Use of the faucet will
not affect the volume of
water delivered for a brew.
However, overuse of the
faucet during a brew may
lower the temperature of
the brew water.
Inlet water will displace a like amount of heated water from the tank.
The hot water will be forced into the brew head where it will spray
over the bed of grounds. Freshly brewed coffee will begin to fill the
container under the brew chamber.
When the flow and all dripping stops, the coffee is ready to serve.
Discard the contents of the brew chamber and rinse it in a sink.
When the ”READY TO BREW” light glows, the brewer is ready for
another brew cycle.
8
605 70988 Owners Manual Integrity 5W Decanter Brewer
Place the appropriate EMPTY decanter in place under the brew
chamber.
CLEANING INSTRUCTIONS
PROCEDURE: Clean Coffee Brewer
CAUTION:
BURN HAZARD
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY:
Daily
TOOLS:
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush, Bottle Brush
Brewing and serving
temperatures of coffee are
extremely hot.
Hot coffee will cause
serious skin burns.
CAUTION:
SHOCK HAZARD
1. Disconnect brewer from electric power.
Allow brewer to cool before cleaning.
Do not submerge or immerse
brewer in water.
2. Remove and empty decanters.
3. Remove and empty brew chamber.
4. Remove the spray disk from the brew head (See figure 8):
Press up on the spray disk ears, then turn the disk to the left
to unlatch. Remove the gasket from inside the brew head.
5. Wipe inside of brew head and area around the brew head
with a soft clean cloth or sponge moistened with clean water.
IMPORTANT:
DO NOT use steel wool, sharp
objects, or caustic, abrasive or
chlorinated cleansers to clean
the brewer or airpots.
6. Wash the spray disk in a sink using warm water and a mild
detergent. A bristle brush may be used to clear clogged
spray holes. Rinse the spray disk with clean water and allow
to air dry.
7. Wash the brew chamber in a sink using warm water and a
mild detergent. A bristle brush may be used to clean the
inside. Rinse with clean water and allow to air dry.
605 70988 Owners Manual Integrity 5W Decanter Brewer
8. Wipe the exterior of the brewer with a soft clean cloth or
sponge moistened with clean water.
10. Reinstall the gasket INSIDE the brew head, then reinstall the
spray disk.
11. Reinstall the brew chamber.
12. Decanters may be washed in a dishwasher or sink.
Fig. 8 Cleaning
Procedure is complete
9
TROUBLESHOOTING SUGGESTIONS
POSSIBLE CAUSE
SUGGESTED REMEDY
Water won’t heat
Brewer unplugged or circuit
breaker tripped
Check power supply cord
Check / reset circuit breaker
Thermostat set too low
Set for desired temperature
Hi-Limit thermostat tripped
Allow to cool
Reset hi-limit
Damaged internal component
or wiring
Examine wiring & connectors,
thermostat and heating element
Repair/replace as needed
Trips hi-limit safety at start-up
No water or too little water
added at start-up
Be sure to add sufficient water
prior to energizing
Coffee level low (pour-over)
Not enough water poured in
Increase water amount
Too much coffee grounds
Adjust amount of grounds
Coffee level too high or low
(automatic)
Timer out of adjustment
Adjust timer
Brew chamber overflows
Too many filter papers or wrong
filter paper
Use one (1) genuine Bloomfield
filter per brew
Brew chamber dispense hole
plugged
Thoroughly clean brew chamber
Too much coffee or too fine a
grind
Adjust coffee amount and grind
Spray gasket missing or
improperly installed
Check/reinstall gasket on
INSIDE of brew head
Spray disk plugged
Clean spray disk
Water supply OFF
Turn water supply ON
Water line strainer plugged
Clean strainer
Water filter (if used) plugged
Replace filter element
Damaged BREW switch
Replace switch
Sprays water from brew head
incorrectly
No brew (automatic)
Damaged internal component or Examine wiring & connectors,
wiring
brew timer and solenoid
Repair/replace as needed
No flow from hot water faucet
Poor coffee quality
Faucet valve turned OFF
Turn faucet valve ON
Faucet plugged
Disassemble faucet, clean
Water not hot enough
Adjust water temp 195-205ºF
Also:
Keep brewer, and decanters clean.
Install a taste and odor filter in water supply, and replace
cartridges regularly.
Use a quality coffee with a consistent roast. Use proper grind and
amount of coffee per brew.
10
605 70988 Owners Manual Integrity 5W Decanter Brewer
SYMPTOM
SERVICING INSTRUCTIONS
ACCESS PANELS
CAUTION:
TOP PANEL:
Remove top panel to access hot water tank, thermostat, heating
elements, brew circuit tubing and faucet tubing.
Top panel is held by two screws at the front and a retaining lip at
the rear.
FRONT PANELS:
Remove upper front panel to access timer and hi-limit. Remove
button plugs for simple adjustments or reset.
Upper front panel is held by two screws at the bottom and a
retaining lip at the top.
SOLENOID DOOR:
Remove solenoid door to access solenoid and tubing
connections.
Solenoid door is held by two screws and a retaining lip.
TERMINAL BLOCK ACCESS:
Remove door to access wiring connections
Access door is held by two screws and a retaining lip.
605 70988 Owners Manual Integrity 5W Decanter Brewer
WARMER PLATES:
Warmer plates unscrew counterclockwise to access warmer
elements and electrical connections.
Fig. 9 Access Panels
11
SHOCK HAZARD
Opening access panels or
removing warmer plates on this
brew may expose uninsulated
electrical components.
Disconnect brewer from
electrical power before
removing any panel.
SERVICING INSTRUCTIONS (continued)
TEMPERATURE ADJUSTMENT
CAUTION:
Unplug power cord or turn circuit breaker OFF. Remove top
panel.
Pull vent tube out of tank lid and insert a thermometer of known
accuracy in hole. Reconnect brewer to electrical power.
Place empty container under brew chamber. Energize brewer
and allow unit to heat. When READY TO BREW light glows,
read the temperature displayed on thermometer.
Adjust WATER TEMP by turning shaft of thermostat; clockwise
increases temperature. Refer to Table 1 below for proper
brewing temperature based on altitude.
Upon completion, remove thermometer and reinstall the plug.
SHOCK HAZARD
These procedures involve
exposed electrical circuits.
These procedures are to be
performed by qualified
technical personnel only.
NOTE:
Optimum brewing temperature
range is 195ºF to 205ºF (90ºC
to 96ºC).
IMPORTANT:
A mechanical thermostat will
maintain temperature within
±5ºF. To prevent boiling water
in the brewer, thermostat should
be adjusted to a maximum
temperature equal to the local
boiling temperature minus 5ºF.
Fig. 10 Checking and Adjusting Brew Temperature
BOILING
POINT OF
WATER
205
IDEAL
BREWING
TEMPERATURE
200
195
0
50
0
1,
00
0
1,
50
0
2,
00
0
2,
50
0
3,
00
0
3,
50
0
4,
00
0
4,
50
0
5,
00
0
5,
50
0
6,
00
0
6,
50
0
190
MAXIMUM
TEMPERATURE
SETTING
ELEVATION (feet above seal level)
BOILING
POINT OF
WATER
97
IDEAL
BREWING
TEMPERATURE
RANGE
94
91
88
0
15
0
30
0
45
0
60
0
75
0
90
0
1.
05
0
1.
20
0
1.
35
0
1.
50
0
1.
65
0
1.
80
1. 0
95
0
TEMP. (ºC)
100
ELEVATION (meters above seal level)
Table 1
Boiling Temperature by Altitude
12
MAXIMUM
TEMPERATURE
SETTING
605 70988 Owners Manual Integrity 5W Decanter Brewer
TEMP. (ºF)
210
SERVICING INSTRUCTIONS (continued)
TIMER ADJUSTMENT
The amount of water dispensed automatically during a brew cycle
is controlled by the timer.
Place empty decanter under brew chamber. Press BREW
button. Brewer should dispense one decanter of water. To
adjust amount:
Remove brew chamber and button plug. Adjust knob on timer;
clockwise increases time. Run several cycles to check amount of
water delivered. Replace button plug.
IMPORTANT: Water pressure
must be between 20 p.s.i and
90 p.s.i. flowing pressure.
If water pressure exceeds this
value, or if water pressure
varies greatly, a pressure
regulator must be installed in
the water supply line.
REMOVE TANK LID ASSEMBLY
Unplug brewer or turn circuit breaker OFF. Turn OFF water
supply. Remove top panel. Pull vent tube and inlet elbow out of
basin pan.
Pull water inlet tube out of basin pan. Remove basin pan.
Disconnect faucet coil at inlet and outlet.
IMPORTANT: Before setting
assembly into tank, make sure
tank lid gasket is properly
seated on flange of lid.
DO NOT OVER-TIGHTEN.
Disconnect all wiring from thermostat and heating element.
Loosen acorn nuts on tank hold-down bracket. Remove holddown bracket by sliding short slotted end off of locking stud and
lifting it off. Remove cover assembly by lifting it straight up.
Reassemble in reverse order.
REPLACE THERMOSTAT
605 70988 Owners Manual Integrity 5W Decanter Brewer
Unplug brewer or turn circuit breaker OFF. Turn OFF water
supply. Remove top panel.
Disconnect all wiring from thermostat only. Loosen and free jam
nut from pass-thru fitting securing temperature sensing bulb.
Remove two screws holding thermostat to bracket.
Lift out thermostat, sensing bulb and thermostat gasket.
Reassemble in reverse order.
REPLACE HEATING ELEMENT
Remove tank lid assembly per above.
Remove two hex nuts holding element to cover. Pull element
from mounting holes.
Reassemble in reverse order.
13
IMPORTANT: When mounting
thermostat, be sure a new seal
washer is placed below the
fitting on the capillary line.
Push sensing bulb thru tank lid
until fitting seats.
Tighten capillary lock nut only
enough to ensure no water
leakage. Excessive tightening
is not necessary.
IMPORTANT: When replacing
heating element, also replace
seal gaskets.
SERVICING INSTRUCTIONS (continued)
REPLACE SOLENOID
Symptom: Automatic brewer will not flow water; or,
automatic brewer drips continuously from brew head.
Unplug power cord or turn circuit breaker OFF. Turn OFF and
disconnect water supply from brewer inlet fitting.
Unscrew water inlet fitting from solenoid.
Remove two screws holding access door in place. Remove two
screws holding solenoid to door.
Disconnect wiring from solenoid.
Slide the 7/16" end of the wrench between the valve body and
the white ring on the extreme end of the metal hose fitting.
Pressure on the white ring toward the metal ferrule releases the
clinch ring, allowing the hose to be easily slid off of the solenoid
bypass outlet.
Transfer solenoid bracket to new solenoid.
Reinstall hose by pressing end of hose onto bypass outlet until it
is fully seated.
Reassemble in reverse order.
CLEAN SOLENOID SCREEN
Symptom: Automatic brewer will not flow water.
Unplug power cord or turn circuit breaker OFF. Turn OFF and
disconnect water supply from brewer inlet fitting.
Unscrew water inlet fitting from solenoid.
Reinsert screen in solenoid. Be careful to maintain correct
orientation. (The OPEN END of the screen goes in FIRST.)
Fig. 11
Fig. 12
Remove Faucet
Supply from Solenoid
Reassemble in reverse order.
Clean Strainer Screen
14
605 70988 Owners Manual Integrity 5W Decanter Brewer
Using needle-nose pliers, withdraw strainer screen from solenoid.
Clean screen under faucet. A stiff bristle brush may be used if
necessary.
SERVICING INSTRUCTIONS (continued)
REPLACE TIMER ASSEMBLY
Unplug power cord or turn circuit breaker OFF.
Remove front panel. Remove knob and three screws holding
timer to bracket. Disconnect wiring to timer.
Reassemble in reverse order.
Adjust timer as described on page 13
REPLACE HOT WATER FAUCET COIL
Symptom: Brewer drips continuously from brew head, except
when faucet valve is turned OFF.
IMPORTANT: When replacing
water faucet coil, also replace
seal gaskets.
Remove tank lid assembly per above.
Remove two hex nuts hot water coil to cover. Pull coil from
mounting holes.
Reassemble in reverse order.
REPAIR HOT WATER FAUCET
Remove top panel and turn faucet valve OFF.
Unscrew aerator cap from faucet and remove handle retaining
clip. Do not let faucet body turn.
Pull bonnet assembly from faucet body.
Examine the interior of the faucet body and the surface of the
seat cup. Clean out any debris in the faucet body, using a stiff
bristle brush if necessary.
Examine the aerator. Clean any debris from the screen or flow
straightener, using a stiff bristle brush if necessary.
605 70988 Owners Manual Integrity 5W Decanter Brewer
Reassemble in reverse order.
REPLACE BREW READY LIGHT or BREW BUTTON
Unplug power cord or turn circuit breaker OFF.
Using Switch Removal Tool (p/n 83209) or a thin screwdriver, pry
light or switch from mounting hole. Disconnect leads.
Reassemble in reverse order.
15
NOTE: Any abrasion or
roughness on the flat end of the
seat cup will require replacing
the seat cup:
Work the seat cup out of the
bonnet and off of the end of the
stem.
Install a new seat cup, making
sure the knob on the stem is
fully inserted into the pocket of
the seat cup, and the skirt of the
seat cup is fully inserted into the
bonnet.
SERVICING INSTRUCTIONS (continued)
CAUTION:
CHEMICAL BURN
HAZARD
Deliming chemicals may be
caustic. Wear appropriate
protective gloves and goggles
during this procedure.
Never siphon deliming
chemicals or solutions by
mouth.
This operation should only be
performed by qualified and
experienced service personnel.
IMPORTANT:
DO NOT spill, splash or pour
water or deliming solution into
or over any internal component
other than the inside of the
water tank.
IMPORTANT:
DO NOT allow any internal
components to come into
contact with the deliming
solution. Take care to keep all
internal components dry.
NOTE: Repeat steps 4 thru 5
as required to remove all scale
and lime build-up.
PROCEDURE: Delime the Water Tank
PRECAUTIONS: Disconnect brewer from electric power.
Allow brewer to cool.
FREQUENCY:
As required (Brewer slow to heat)
TOOLS:
Deliming Solution
Protective Gloves, Goggles & Apron
Mild Detergent, Clean Soft Cloth or Sponge
Bristle Brush, Bottle Brush
Large Sink (or other appropriate work area)
1. Unplug power cord. Turn off the water shut-off valve and
disconnect the water supply line from the brewer inlet fitting.
2. Remove the tank lid assembly as described on page 13.
3. Remove the water tank from the brewer body by lifting
straight up. Empty all water from the tank. Set the tank back
into the brewer.
4. Mix 2 quarts of deliming solution according to the
manufacturer’s directions. Carefully pour the deliming
solution into the water tank. Lower the lid assembly back
onto the tank. Allow to sit for 30 minutes, or as directed by
the manufacturer.
6. Remove the tank from the brewer and empty. Using a stiff
bristle brush, scrub the interior of the water tank to remove
lime and calcium build-up. Rinse with clean water.
16
605 70988 Owners Manual Integrity 5W Decanter Brewer
5. At end of soaking period, remove lid assembly from tank.
Thoroughly rinse internal components of lid assembly with
clear water. Using a stiff bristle brush, scrub the heating
element and faucet water coil to remove lime and calcium
build-up. Rinse with clean water. Store lid assembly in a safe
location.
SERVICING INSTRUCTIONS (continued)
7. Set the tank back into the brewer. Reassemble the tank lid to
the water tank. Make sure the gasket is properly in place,
then reinstall lid clamps.
8. Reinstall wiring to heating element and thermostat.
Reassemble piping for the faucet. Verify that all internal
components are dry, then reinstall the top panel.
10. Reconnect brewer to electrical supply and reconnect water
supply.
11. Install the brew chamber without filter paper or grounds.
Run at least three full brew cycles and discard all water
generated.
605 70988 Owners Manual Integrity 5W Decanter Brewer
12. Brewer is ready to use.
17
NOTE: Normally, silicone
hoses do not need to be
delimed. Should deliming
hoses become necessary,
Bloomfield recommends
replacing the hoses.
EXPLODED VIEW & PARTS LIST
CABINET
ASSEMBLY
ITEM
PART NUMBER
1
8700-16
PLATE, WARMER COVER
4
8543-80
CLIP, MOUNTING
23
BUSHING, HEYCO 1/78
33
8543-42
34
82727
34a
8543-85
35
85089
48
8516-150
81732
8706-75
101
GASKET, SPRAYHEAD
SPRAY DISK, EMBOSSED
RETAINER, SPRAY DISK (DRILL & RIVET REQUIRED TO INSTALL)
DOOR, SOLENOID
LEG SET, BLACK PLASTIC (pk 4)
LEG ASSY 1”
BUTTON PLUG, 2”
ASSEMBLY, BASIN BODY
102
8542-6
COVER, BASIN TOP (INCLUDES 86666 POUR-OVER ASSY)
103
86666
ASSEMBLY, POUR OVER, PLASTIC
108
8541-21
BASIN
110
8751-17
PLATE, BOTTOM, 8750-SERIES
111
ASSEMBLY, BODY 8750-SERIES
112
COVER, UPPER LEFT
113
COVER, UPPER RIGHT
114
COVER, FRONT UPPER
115
COVER, FRONT LOWER
116
86903
117
8718-48
120
ACCESS, TERMINAL BLOCK
BRACKET, HI-LIMIT MOUNTING
86871
LABEL, BASIN FRONT (8752)
86873
LABEL, BASIN FRONT (8752KFT)
200
8942-6B
201
POF
BREW CHAMBER, BLACK PLASTIC
FILTER PAPER (CS 1000)
18
605 70988 Owners Manual Integrity 5W Decanter Brewer
70
DESCRIPTION
EXPLODED VIEW & PARTS LIST (continued)
605 70988 Owners Manual Integrity 5W Decanter Brewer
ELECTRICAL
COMPONENTS
ITEM
PART NUMBER
2
8572-18
DESCRIPTION
ELEMENT, WARMER 120V 100W
30
8707-55
SWITCH, BREW (MOMENTARY)
31
8528-40
SWITCH, TANK HEATER 240V 20A
32
8738-2
INDICATOR LIGHT 120V GREEN
35
8718-1
TIMER W/KNOB 2-MIN
36
8552-18
TERMINAL BLOCK 4P
39
86945
SWITCH, WARMER
45
85685
SOLENOID 120V W/ BYPASS .75GPM
50
86280
THERMOSTAT 199ºF
63
8552-50
HI-LIMIT SAFETY MANUAL RESET
67
8716-1
ELEMENT, HEATER 230V 3500W
19
EXPLODED VIEW & PARTS LIST
HOT WATER TANK ASSEMBLY
ITEM
PART NUMBER
DESCRIPTION
8043-5
HOLD-DOWN STRAP
14
8942-92
NUT 8-32 HEX KEPS
50
86280
THERMOSTAT 199ºF
54
8043-12
GASKET, TANK COVER
55
8043-28
NUT, HEX 1/2-20 BRASS
56
8043-30
GASKET, SEAL
57
8941-21
NUT, HEX 7/16-20 BRASS
58
8540-6
HOT WATER COIL
59
8043-8
ELBOW, INLET
60
8043-15
VENT TUBE
61
8043-11
ELBOW, OUTLET
62
8514-68
TANK COVER, 8-HOLES
66
8043-24
WATER INLET TUBE
66a
8543-73
SCREW, 4-40 x 1 PH
66b
8543-74
NUT, HEX 4-40
67
8716-1
ELEMENT, HEATING 230V 3500W
68
8043-10
TANK BODY
20
605 70988 Owners Manual Integrity 5W Decanter Brewer
13
EXPLODED VIEW & PARTS LIST (continued)
605 70988 Owners Manual Integrity 5W Decanter Brewer
PLUMBING COMPONENTS
ITEM
PART NUMBER
8
8540-3
DESCRIPTION
ASSEMBLY, FORMED TUBE FAUCET SUPPLY
9
86904
TUBE, FORMED ASSEMBLY 1/4FF x 1/4 FF
10
80154
FITTING, UNION 1/4MF x 1/4MF
12*
82556
ASSEMBLY, FAUCET
24
8043-26
TUBE, BREW OUTLET METAL
25
8043-13
ELBOW, BREW SPRAY
26
82680
27
8551-100B
28
82681
WASHER, FLAT 15/32 x 1-1/8 x .048 SS
29
85778
ASSEMBLY, BRAIDED TUBE W/BALL VALVE 14”
33
8543-42
NUT, HEX 7/16-20 Ni
WASHER, LOCK 7/16”
GASKET, SPRAYHEAD
34
82727
34A
8543-85
SPRAY DISK, EMBOSSED
43
86905
TUBE, BASIN WATER INLET 11”
45*
85685
SOLENOID 120V W/ BYPASS .75GPM
59
8043-8
ELBOW, TANK WATER INLET
60
8043-15
VENT TUBE
61
8043-11
ELBOW, TANK WATER OUTLET
108
8541-21
BASIN PAN
RETAINER, SPRAY DISK (DRILL & RIVET REQUIRED TO INSTALL)
* For REPAIR KITS see page 22.
21
EXPLODED VIEW & PARTS LIST (continued)
SERVICE KITS
FAUCET REPAIR KITS
82573
Handle (item 12a)
82575
Seat Cup (item 12c)
82576
Faucet Repair Kit (Includes 12a Handle, 12c Seat Cup, 12d Spring,
12h Stem, 12j Pin & 12k Bonnet
82682
Retainer Clip (item 12b)
84804
Aerator Replacement Kit (Includes 12e O-Ring, 12f Aerator Disk &
12g Aerator Cap
84870
Aerator Repair Kit (Includes 12e O-Ring & 12f Aerator Disk)
22
605 70988 Owners Manual Integrity 5W Decanter Brewer
SOLENOID REPAIR KITS
85218
Inlet Fitting Kit (items 45-10, 45-11, 45-12, 45-13)
85219
Inlet Strainer (item 45-13)
605 70988 Owners Manual Integrity 5W Decanter Brewer
WIRING DIAGRAM
23
Bloomfield Industries proudly supports CFESA
Commercial Food Equipment Service Association
Bloomfield Industries, Inc.
Division of Carrier Commercial Refrigeration
In US and Canada
Telephone: 775-689-5700
Fax:
888-492-2783
Fax:
800-356-5142 (for orders only)
website: www.wellsbloomfield.com
PRINTED IN UNITED STATES OF AMERICA