Baxi Potterton Gold H Range Technical data

You can rely on
Installation & Service Instructions
Gold H
Range
Condensing
Boiler
These instructions include the Benchmark Commissioning
Checklist and should be left with the user for safe keeping.
© Baxi Heating UK Ltd 2014
Natural Gas
Building Regulations and the Benchmark
Commissioning Checklist
Potterton Gold H 15
G.C.No 41-592-12
Potterton Gold H 18
G.C.No 41-592-13
Potterton Gold H 24
G.C.No 41-592-14
Building Regulations (England & Wales) require notification of
the installation of a heating appliance to the relevant Local
Authority Building Control Department. From 1 April 2005 this
can be achieved via a Competent Persons Self Certification
Scheme as an option to notifying the Local Authority directly.
Similar arrangements will follow for Scotland and will apply in
Northern Ireland from 1 January 2006.
The Health & Safety Executive operates the ‘Gas Safe Register’,
a self-certification scheme for gas heating appliances.
These arrangements represent a change from the situation
whereby compliance with Building Regulations was accepted as
being demonstrated by completion of the Benchmark Logbook
(which was then left on site with the customer).
With the introduction of Self Certification Schemes, the
Benchmark Logbook is being withdrawn. However, a similar
document in the form of a commissioning checklist and service
interval record is incorporated at the back of these instructions.
The Benchmark Scheme
Benchmark places responsibilities on both manufacturers and installers. The
purpose is to ensure that customers are provided with the correct equipment for
their needs, that it is installed, commissioned and serviced in accordance with the
manufacturer’s instructions by competent persons and that it meets the
requirements of the appropriate Building Regulations. The Benchmark Checklist
can be used to demonstrate compliance with Building Regulations and should be
provided to the customer for future reference.
Installers are required to carry out installation, commissioning and servicing work
in accordance with the Benchmark Code of Practice which is available from the
Heating and Hotwater Industry Council who manage and promote the Scheme.
Visit www.centralheating.co.uk for more information.
© Baxi Heating UK Ltd 2014 All rights reserved. No part of this publication may
be reproduced or transmitted in any form or by any means, or stored in any
retrieval system of any nature (including in any database), in each case whether
electronic, mechanical, recording or otherwise, without the prior written
permission of the copyright owner, except for permitted fair dealing under
Copyrights, Designs and Patents Act 1988.
This company is a member of the Benchmark initiative and fully
supports the aims of the programme. Its aim is to improve the
standards of installation and commissioning of central heating
systems in the UK and to encourage the regular servicing of all
central heating systems to ensure safety and efficiency.
Building Regulations require that installations should comply
with manufacturer's instructions. It is therefore important that
the commissioning checklist is completed by the installer. The
relevant section of Building Regulations only relates to
dwellings. Therefore the checklist only applies if the appliance is
being installed in a dwelling or some related structure.
The flowchart opposite gives guidance for installers on the
process necessary to ensure compliance with Building
Regulations.
Applications for the copyright owner’s permission to reproduce or make other
use of any part of this publication should be made, giving details of the proposed
use, to the following address:
The Company Secretary, Baxi Heating UK Limited,
Brooks House, Coventry Road, Warwick. CV34 4LL
Full acknowledgement of author and source must be given.
WARNING: Any person who does any unauthorised act in relation to a
copyright work may be liable to criminal prosecution and civil claims for damages.
0086
ISO 9001
FM 00866
2
© Baxi Heating UK Ltd 2014
Installer Notification Guidelines
Choose Building
Regulations Notification
Route
Competent Person's
Self Certification Scheme
Building Control
Install and Commission this
appliance to manufacturer's
instructions
Contact your relevant Local
Authority Building Control
(LABC) who will arrange
an inspection or contact
a government approved
inspector
Complete the
Benchmark Checklist
If you notify via the ‘Gas Safe
Register’, the register will issue
the Building Regulations
certificate on members’ behalf
Install and Commission this
appliance to manufacturer's
instructions
Scheme Members only
Call ‘Gas Safe Register’ on:
0800 408 5577
or log onto:
www.gassaferegister.co.uk
within 10 days
Complete the
Benchmark Checklist
You must ensure that the
certificate number issued by
the ‘Gas Safe Register’ is written
onto the Benchmark Checklist
‘Gas Safe Register’ will issue a
Building Regulations Compliance
Certificate to the property owner
and inform the relevant LABC
© Baxi Heating UK Ltd 2014
LABC will record the data
and will issue a
certificate of compliance
3
Legislation
IMPORTANT - Installation, Commissioning, Service & Repair
This appliance must be installed in accordance with the manufacturer’s instructions and
the regulations in force. Read the instructions fully before installing or using the
appliance.
In GB, this must be carried out by a competent person as stated in the Gas Safety
(Installation & Use) Regulations.
Definition of competence: A person who works for a Gas Safe registered company
and holding current certificates in the relevant ACS modules, is deemed competent.
In IE, this must be carried out by a competent person as stated in I.S. 813 “Domestic
Gas Installations”.
NOTE: The addition of anything that may interfere with the normal operation of the
appliance without express written permission from the manufacturer or his agent could
invalidate the appliance warranty. In GB this could also infringe the Gas Safety
(Installation and Use) Regulations.
Warning - Check the information on the data plate is compatible with local supply
conditions.
All Gas Safe registered engineers carry an ID card with their licence number and a
photograph. You can check your engineer is registered by telephoning
0800 408 5500 or online at www.gassaferegister.co.uk
The boiler meets the requirements of Statutory Instrument “ The Boiler (Efficiency)
Regulations 1993 No 3083” and is deemed to meet the requirements of Directive
92/42/EEC on the energy efficiency requirements for new hot water boilers fired with
liquid or gaseous fuels:Type test for purpose of Regulation 5 certified by:
Notified Body 0086.
Product/Production certified by:
Notified Body 0086.
For GB/IE only.
This company declares that no substances harmful
to health are contained in the appliance or used
during appliance manufacture.
The appliance is suitable only for installation in GB and IE
and should be installed in accordance with the rules in
force, and only used in a suitably ventilated location.
In GB, the installation must be carried out by a Gas Safe
Registered Installer. It must be carried out in accordance
with the relevant requirements of the:
• Gas Safety (Installation & Use) Regulations.
• The appropriate Building Regulations either The Building
Regulations, The Building Regulations (Scotland), Building
Regulations (Northern Ireland).
• The Water Fittings Regulations or Water Byelaws in
Scotland.
• The Current I.E.E. Wiring Regulations.
Where no specific instructions are given, reference should
be made to the relevant British Standard Code of Practice.
In IE, the installation must be carried out by a competent
Person and installed in accordance with the current edition
of I.S. 813 ‘Domestic Gas Installations’, the current Building
Regulations and reference should be made to the current
ETCI rules for electrical installation.
All systems must be thoroughly flushed and treated
with inhibitor (see section 6.2).
Codes of Practice, most recent version should be used
In GB the following Codes of Practice apply:
Standard
Scope
BS 6891
Gas Installation.
BS 5546
Installation of hot water supplies for domestic
purposes.
BS EN 12828
Heating systems in buildings.
BS EN 14336
Installation & commissioning of water based
heating systems.
BS 6798
Installation of gas fired hot water boilers.
BS 5440 Part 1
Flues.
BS 5440 Part 2
Ventilation.
BS 7074
Expansion vessels and ancillary equipment for
sealed water systems.
BS 7593
Treatment of water in domestic hot water
central heating systems.
In IE the following Codes of Practice apply:
Standard
Scope
I.S. 813
Domestic Gas Installations.
The following BS standards give valuable additional information;
BS 5546
Installation of hot water supplies for domestic
purposes.
BS EN 12828
Heating systems in buildings.
BS EN 14336
Installation & commissioning of water based
heating systems.
BS 7074
Expansion vessels and ancillary equipment for
sealed water systems.
BS 7593
Treatment of water in domestic hot water
central heating systems.
4
© Baxi Heating UK Ltd 2014
Safe Manual Handling
General
The following advice should be adhered to, from when first handling the boiler to the final stages of installation, and also during maintenance.
Most injuries as a result of inappropriate handling and lifting are to the back, but all other parts of the body are vulnerable, particularly shoulders, arms and
hands. Health & Safety is the responsibility of EVERYONE.
There is no ‘safe’ limit for one man - each person has different capabilities. The boiler should be handled and lifted by TWO PEOPLE.
Do not handle or lift unless you feel physically able.
Wear appropriate Personal Protection Equipment e.g. protective gloves, safety footwear etc.
Preparation
Co-ordinate movements - know where, and when, you are both going.
Minimise the number of times needed to move the boiler - plan ahead.
Always ensure when handling or lifting the route is clear and unobstructed. If possible avoid steps, wet or slippery surfaces, unlit areas etc. and take special
care on ladders/into lofts.
Technique
When handling or lifting always use safe techniques - keep your back straight, bend your knees. Don’t twist - move your feet, avoid bending forwards and
sideways and keep the load as close to your body as possible.
Where possible transport the boiler using a sack truck or other suitable trolley.
Always grip the boiler firmly, and before lifting feel where the weight is concentrated to establish the centre of gravity, repositioning yourself as necessary.
See section 8.3 of these instructions for recommended lift points.
Remember
The circumstances of each installation are different. Always asses the risks associated with handling and lifting according to the individual conditions.
If at any time when installing the boiler you feel that you may have injured yourself STOP !!
DO NOT ‘work through’ the pain - you may cause further injury.
IF IN ANY DOUBT DO NOT HANDLE OR LIFT THE BOILER - OBTAIN ADVICE OR ASSISTANCE BEFORE PROCEEDING !!
© Baxi Heating UK Ltd 2014
5
Contents
Section
6
© Baxi Heating UK Ltd 2014
Page
1.0
Introduction
7
2.0
General Layout
8
3.0
Appliance Operation
9
4.0
Technical Data
10
5.0
Dimensions and Fixings
11
6.0
System Details
12
7.0
Site Requirements
16
8.0
Flue Options
21
9.0
Plume Displacement
26
10.0
Installation
30
11.0
Electrical
36
12.0
Commissioning the Boiler
38
13.0
Fitting the Outer Case
41
14.0
Servicing the Boiler
42
15.0
Changing Components
45
16.0
Short Parts List
51
17.0
Fault Finding
52
Benchmark Checklist
58
1.0 Introduction
1.1
Description
1. The Potterton Gold H range are gas fired room sealed fan
assisted condensing central heating boilers.
2. The maximum outputs of the Baxi Solo models are:15 H - 15.24 kW (Non Condensing)
16.49 kW (Condensing)
18 H - 17.81 kW (Non Condensing)
19.27 kW (Condensing)
24 H - 22.0 kW (Non Condensing)
23.8 kW (Condensing)
All boilers automatically adjust output according to system load.
3. It is designed for use on Natural Gas (G20).
4. The boiler is suitable for fully pumped open vented central
heating and domestic hot water systems and sealed systems.
Fig. 1
Position of Label
5. A label giving details of the model, serial number and Gas
Council number is situated on the rear of the lower door panel
(Fig. 1).
6. The boiler data badge is positioned on the air box door
(Fig. 2).
7. The boiler is intended to be installed in residential / domestic
environments on a governed meter supply only.
8. The boiler must be installed with one of the purpose
designed flues such as the standard horizontal flue kit, part no
236921.
1.2
Air Box Door
Fig. 2
Data Badge
Important Information
Man-made mineral fibre
• Some component parts of this appliance (insulation pads,
gaskets and rope seals) are manufactured from man-made
mineral fibre.
• Prolonged or excessive exposure to this material may result
in some irritation to the eyes, skin or respiratory tract.
• It is advisable to wear gloves when handling these items.
• Irritant dust will only be released from the items if they are
broken up or subjected to severe abrasion. In these instances a
suitable dust mask and goggles should be worn.
• Always thoroughly wash hands after installation, servicing or
changing components.
• When disposing of any items manufactured from man-made
mineral fibre care must be exercised.
• If any irritation of the eyes or severe irritation of the skin is
experienced seek medical attention.
1.3
Contents of Pack
The pack contains:• Boiler
• Wall Plate
• Template & ‘Quick Fit’ Guide
• Literature Pack
• Fittings Pack
© Baxi Heating UK Ltd 2014
7
2.0 General Layout
2.1
16
Fig. 5
15
2
14
1
3
13
12
4
5
6
Fig. 3
7
9
8
11
Fig. 4
8
© Baxi Heating UK Ltd 2014
Fig. 6
10
Layout (Figs. 3,4,5 & 6)
1.
Wall Plate
2.
Flue Elbow
3.
Heat Exchanger
4.
Burner
5.
Air Box
6.
Fan Protection Thermostat
7.
Fan Assembly
8.
Condensate Trap
9.
PCB Housing Assembly
10.
Gas Service Cock
11.
Gas / Air Ratio Valve
12.
Flow Pipe Connection
13.
Return Pipe Connection
14.
Flow Temperature Safety Thermostat - Black
15.
Flow Temperature Thermistor - Red
16.
Flow Switch (dry fire protection)
Mains On.
3.0 Appliance Operation
Flow
temperature less
than set point ?
3.1
NO
1. Switched Live On: When the switched live switches
on if the flow temperature is less than the set point
then pump overrun occurs. When the switched live
switches on if the flow temperature is greater than the
set point then pump overrun occurs.
YES
10 second
Pump On.
NO
2. Pump On: The pump is on while the fan, spark
generator and gas valve are off. After 10 seconds if the
flow switch has made then fan pre-purge occurs. After
10 seconds if the flow switch has not made then anticycle occurs.
Flow switch made ?
YES
5 second
Fan Pre-Purge.
YES
Ignition done
and less than 5
attempts made ?
5 second
Ignition Period.
Flame Detected ?
Ignition done and
5 attempts made ?
YES
Burner On.
All TRVs
shut or Flow temperature
greater than set point ?
YES
5 second
Fan Post Purge.
YES
All TRVs
shut down ?
NO
YES
Ignition
Lockout.
3. Fan Pre-Purge: The pump and fan are on while the
spark generator and gas valve are off. After 5 seconds
ignition occurs.
4. Ignition: The pump, fan, spark generator and gas
valve are on. If a flame is detected then burner on
occurs. If a flame is not detected within 5 seconds and
less than 5 ignition attempts have been made then fan
purge occurs. If a flame is not detected within 5
seconds and 5 ignition attempts have been made then
ignition lockout occurs.
5. Burner On: The pump, fan and gas valve are on
while the spark generator is off. Flow temperature is
controlled by varying the fan speed (and thereby the
gas rate) to achieve optimum operation. If the flow
temperature is greater than the set point or the TRVs
all shut down then fan post purge occurs.
6. Fan Post Purge: The pump and fan are on while the
spark generator and gas valve are off. After 5 seconds if
the TRVs are not shut down then pump overrun
occurs. After 5 seconds if the TRVs are shut down then
anti-cycle occurs.
7. Pump Overrun: The pump is on while the fan, spark
generator and gas valve are off. After 1 minute anticycle occurs.
8. Anti-cycle: The pump, fan, spark generator and gas
valve are off. After 3 minutes if the flow temperature is
less than the set point then pump on occurs. After 3
minutes if the flow temperature is greater than the set
point then pump overrun occurs.
9. Ignition Lockout: The pump, fan, spark generator
and gas valve are off. The boiler can only be reset by
manually using the reset button.
1 minute
Pump Overrun.
3 minute
Anti-cycle.
© Baxi Heating UK Ltd 2014
9
4.0 Technical Data
4.1
Appliance Type
C13
C33
Appliance Category
C53
CAT I 2H
Max
Min
15 model
kW
16.88
10.2
18 model
kW
20.18
10.2
24 model
kW
24.50
10.2
Heat Output (P)
(Non Condensing 70° C Mean Water Temp)
Max
Min
15 model
kW
15.24
9.14
18 model
kW
17.81
9.14
24 model
kW
22.00
9.14
Heat Output (P)
(Condensing 40° C Mean Water Temp)
Max
Min
15 model
kW
16.49
18 model
kW
19.27
24 model
kW
23.8
Max Gas Rate
(After 10 Mins)
(2H - G20 - 20mbar)
m /hr
3
(15)
(18)
(24)
1.64
1.94
2.31
Injector (Natural Gas)
6.5mm Diameter
Nox Class
Heat Input (Q)(Gross)
10.1
10.1
SEDBUK Declaration
For 15 model - The efficiency is 91.3%
For 18 model - The efficiency is 90.4%
For 24 model - The efficiency is 90.9%
This value is used in the UK Government’s Standard
Gold H 15, 18 & 24
Electrical Supply
230V~ 50Hz
(Appliance must be connected to an
earthed supply)
5
Horizontal
Flue Terminal
Dimensions
Diameter
Projection
Connections
Gas Supply
Central Heating Flow
Central Heating Return
Condensate Drain
Outercase Dimensions
Overall Height Inc Flue Elbow
Casing Height
Casing Width
Casing Depth
110mm
150mm
-
Static Head
max
min
(For unventilated compartments see Section 7.2)
Weights
Packaged Boiler Carton
Packaged Flue Kit
Installation Lift Weight
kg
36.2
3.6
26.0
IPX2
30 metres (100 ft)
1 metre (3.25 ft)
Low Head
0.2m (8 in) min
System Detail
fully pumped open vented & sealed systems
Gas Connection
G1/2” B.S.P. Thread
CO/CO2 Ratio
Up to a maximum
of 0.004
CO2 Level
9% ± 1%
Controls
boiler thermostat, safety thermostat,
flow switch, electronic flame sensing,
temperature protection thermostat &
condensate blockage sensor
Inlet Pressure at Gas Valve (Natural Gas)
Min
18.1 mbar
Assessment Procedure (SAP) for energy rating of
Max
dwellings. The test data from which it has been
calculated has been certified by 0087.
3A
Water Content
litres
2.6
pints
4.6
Clearances
5mm Min
200mm Min
50mm Min
500mm Min
5mm Min
External Fuse Rating
Electrical Protection
750mm
600mm
390mm
280mm
Both Sides
Above Casing
Below Casing
Front (For Servicing)
Front (In Operation)
80W
Internal Fuse Rating (BS 4265)
Fuse
3.15 AT (PCB)
/2in BSPT
22mm
22mm
1 in BSP
1
-
Power Consumption
NOTE: All data in this section are nominal values
and subject to normal production tolerances
22.5 mbar
(see Section 12.1)
Flow Temperature (adjustable)
55° C to 78° C (± 5° C)
Recommended System
Temperature Drop
Condensing
20°C
36°F
91
83
75
66
58
50
42
33
25
17
8
220
200
180
160
140
120
100
80
60
40
20
0
10
20
30
Water Flow Rate (litres/min)
10
© Baxi Heating UK Ltd 2014
40
Pressure Drop (in wg)
Pressure Drop (mbar)
Hydraulic Resistance Chart
5.0 Dimensions and Fixings
DIMENSIONS
A 600mm
E
At Least 1.5°
B 280mm
C 390mm
A
D 150mm Ø Min.
E 162.5mm
F 96mm
B
360° Orientation
C
D
Tube Ø 110mm
The 1.5° fall provided by the elbow
is to allow condensate to run back to
the boiler, for disposal through the
condensate discharge pipe.
Fig. 7
F
Y
X
At Least 1.5°
SIDE FLUE (left and right)
For every 1m of horizontal flue
length, the clearance above the top
of the flue elbow should be 27.5mm
to incorporate the 1.5° fall in the flue
from the terminal to the elbow.
Flue length (Y)
Clearance (X)
up to 1m
27.5mm
1m - 2m
55mm
2m - 3m
82.5mm
Fig. 8
© Baxi Heating UK Ltd 2014
11
6.0 System Details
6.1
Water Circulating Systems
1. The appliance is suitable for use with open vent fully
pumped systems and sealed systems .
The following conditions should be observed on all
systems:
• The static head must not exceed 30m (100ft) of water.
• The boiler must not be used with a direct cylinder.
• Drain cocks should be fitted to all system low points.
• All gas and water pipes and electrical wiring must be
installed in a way which would not restrict the servicing
of the boiler.
• Position isolating valves as close to circulating pump as
possible.
• It is recommended that the return pipe is fitted with an
automatic air vent as close to the boiler as is practical.
6.2
Treatment of Water Circulating Systems
1. All recirculatory water systems will be subject to
corrosion unless they are flushed and an appropriate water
treatment is applied. To prevent this, follow the guidelines
given in BS 7593 “Treatment of Water in Domestic Hot
Water Central Heating Systems” and the treatment
manufacturers instructions.
2. Treatment must involve the use of a proprietary
cleanser, such as Sentinel X300 or X400, or Fernox F3 and
an inhibitor such as Sentinel X100 or Fernox MB-1.
3. Full instructions are supplied with the products, for
further information contact Sentinel (0800 389 4670) or
Fernox (0870 870 0362).
Failure to flush and add inhibitor to the system will
invalidate the appliance warranty.
4. It is important to check the inhibitor concentration after
installation, system modification and at every service in
accordance with the inhibitor manufacturer’s instructions.
(Test kits are available from inhibitor stockists.)
5. For information or advice regarding any of the above
contact Technical Enquiries 0844 871 1555.
12
© Baxi Heating UK Ltd 2014
6.0 System Details
Copper
0.5m
Copper
0.5m
Flow
Boiler
6.3
Return
Copper
1m
1. The sizes of flow and return pipes from the boiler should
be determined by normal methods, according to the
requirements of the system. The connections on the boiler
are 22mm.
Fig. 9
mm
500
45°
1000mm
Min
2. A 20 °C (36°F) drop in temperature across the system is
recommended for condensing boilers. Existing radiators may
be oversized and so allow this, but where radiator sizing is
marginal it may be advisable to retain a system temperature
drop of 11°C (20°F).
22mm
Open Vent
15mm
Cold
Feed
400mm
Min Head
3. In systems using non-metallic pipework it is necessary to
use copper pipe for the boiler Flow and Return. The copper
must extend at least 1 metre from the boiler and include any
branches (Fig. 9).
150mm
Max
Boiler
Pump
6.4
Flow
Typical Low Head Installation
mm
a) The pump being adjusted to give a 20°C drop across
the boiler.
b) The pump must be fitted on the flow.
c) The pump must be fitted in accordance with the
pump manufacturer's instructions.
d) The open vent pipe must be taken up from a tee in a
horizontal section of the flow pipe.
22mm
Open Vent
500
45°
Automatic Air
Vent
15mm
Cold
Feed
1000mm
Min
Boiler
Low Head Installation
1. Using a close couple arrangement the minimum head is as
shown in the diagrams (Figs. 10 & 11) subject to the
following conditions:
Return
Fig. 10
Pipework
An alternative Low Head Installation (Fig. 12)
400mm
Min Head
2. For heads below 400mm then a combined vent and feed
pipe may be connected. This must be a minimum of 22mm
diameter. It is recommended that an air separator is fitted
when using a combined feed and vent pipe.
150mm
Max
Pump
Flow
Return
200mm
Min
Pump
1. Providing that the cold feed and open vent pipe are
positioned correctly (e.g. the system is not prone to
pumping over, air entrainment etc.) the pump may be fitted
on the primary return pipe.
If Conditions Require,
This System Possible
Fig. 11
6.5
22mm
Feed & Vent
Pipe
Air
Separator
Boiler
Pump
Flow
Return
Fig. 12
Alternative Low Head Installation
© Baxi Heating UK Ltd 2014
13
230V
50Hz
Key to colours
L N E
g/y
Y Plan
Diverter
Valve
b
w
Cylinder
Stat
gr
1
Room
Stat
o
C 2
Boiler
L
E
N P/F
Timer
L
N
CH on
HW on
HW off
Y Plan, Room Thermostat System, CH Interlocked By Room Thermostat
At least the Radiator(s) near the Room Thermostat not TRV’d
Pump run from Switched Live
By-pass permitted but not required for Part L1 compliance
230V
50Hz
gr
b
gr
L N E
Motor
b
Motor
br
br
g/y
S Plan
Valve
Room Cylinder
Stat
Stat
o
S Plan
Valve
g/y
o
Boiler
L
E
N P/F
NE L
Blue
Brown
White
Orange
Grey
Green/Yellow
6.0 System Details
6.6
System Controls
This boiler does not require a bypass.
This boiler does not require a permanent live.
The pump only needs wiring directly to the boiler for
fully TRV’d systems.
a) zone controls
b) timing controls
c) boiler control interlocks
2. Such a system needs to be fully pumped and must
provide independent temperature and time control to
both the heating and hot water circuits and have a boiler
interlock.
3. The boiler should be controlled so that it operates on
demand only. Where it is proposed to effect control by
thermostatic radiator valves, a room thermostat (or
other device such as a flow switch - a flow switch is
integral to this boiler) should also be provided to switch
off the boiler when there is no demand for heating or
hot water.
4. The interlock for the CH circuit can be provided by
either a Room Thermostat or a fully TRV’d system with
the pump wired back to the boiler without a bypass.
Connection diagrams for both options for Y and S plan
systems are shown.
Timer
L
N
CH on
HW on
-
1. To comply with Part L1 of the Building Regulations the
heating system into which the boiler is installed should
include the following:
Pump
NE L
b
br
w
o
gr
g/y
Pump
S Plan, Room Thermostat System, CH Interlocked By Room Thermostat
At least the Radiator(s) near the Room Thermostat not TRV’d
Pump run from Switched Live
By-pass permitted but not required for Part L1 compliance
230V
50Hz
L N E
g/y
Y Plan
Diverter
Valve
b
w
Cylinder
Stat
230V
50Hz
L N E
Motor
b
o
S Plan
Valve
g/y
br
C 2
Motor
br
gr
1
gr
b
gr
o
g/y
S Plan
Valve
Cylinder
Stat
o
Boiler
L
E
Timer
L
N
CH on
HW on
NE L
Pump
Y Plan, Fully TRV’d System, CH Interlocked By Boiler Flow Switch
Room Thermostat should not be fitted
Pump must be run from Boiler P/F connection for Part L1 compliance
By-pass not permitted (must be valved off) for Part L1 compliance
© Baxi Heating UK Ltd 2014
L
E
N P/F
Timer
HW off
14
Boiler
N P/F
L
N
CH on
HW on
NE L
Pump
S Plan, Fully TRV’d System, CH Interlocked By Boiler Flow Switch
Room Thermostat should not be fitted
Pump must be run from Boiler P/F connection for Part L1 compliance
By-pass not permitted (must be valved off) for Part L1 compliance
6.0 System Details
3 Litre
Top Up Bottle
(if required)
Air
Vent
Safety
Valve
Filling
Point
Pressure
Gauge
Pump
Radiator
Circuit
Expansion
Vessel
System Drains at
Low Point
Max Boiler Flow
Temp = 82° C
Method of determining minimum valve of
expansion vessel volume for sealed systems
using Potterton Boilers
Vessel Charge
Pressure (Bar)
Initial System
Pressure (Bar)
Multiply Total
Water Content Of
System By (Litres)
0.5
0.5
1.0
1.5
2.0
0.067
0.112
0.207
0.441
1.0
1.5
2.0
0.087
0.152
0.330
1.5
2.0
0.125
0.265
1.0
1.5
Example :- System Volume = 75 litres
Vessel Charge Pressure = 1.0 bar
Initial System Pressure = 1.5 bar
Then :- 75 x 0.152 = 11.4 litres
Expansion Vessel Volume
Table. 1
Sealed Systems (Fig. 13)
1. SAFETY VALVE - A safety valve complying with the
requirements of BS 6750 Part 1 must be fitted close to
the boiler on the flow pipe by means of a horizontal or
vertically upward connection with no intervening valve
or restrictions and should be positioned to facilitate
testing. The valve should be pre-set and non-adjustable
to operate at a pressure of 3 bar (45 Ibf/in2). It must be
arranged to discharge any water or steam through a pipe
to a safe outlet position.
2. PRESSURE GAUGE - A pressure gauge of minimum
range 0-4 bar (0-60 Ibf/in2) with a fill pressure indicator
must be fitted to the system, preferably at the same
point as the expansion vessel in an easily visible position.
Boiler
Fig. 13
6.7
NOTE
Where a vessel of the calculated size is not obtainable then
the next available larger size should be used.
3. EXPANSION VESSEL - An expansion vessel
complying with the requirements of BS 4814 must be
fitted to the system by means of a connection close to
the inlet side of the circulating pump in accordance with
the manufacturers instructions, the connecting pipe being
unrestricted and not less than 15mm (1/2 in) nominal size.
The volume of the vessel should be suitable for the
system water content and the nitrogen or air charge
pressure should not be less than the system static head
(See Table. 1).
Further details of sealed system design can be obtained
from BS 5449 and the British Gas publication entitled
'Specifications for Domestic Wet Central Heating
Systems'.
4. FILLING POINT - A filling point connection on the
central heating return pipework must be provided to
facilitate initial filling and pressurising and also any
subsequent water loss replacement / refilling. The sealed
primary circuits may be filled or replenished by means of
a temporary connection between the primary circuit and
a supply pipe provided a ‘Listed’ double check valve or
some other no less effective backflow prevention device
is permanently connected at the inlet to the circuit and
the temporary connection is removed after use. The
filling method adopted must be in accordance with all
relevant water supply regulations and use approved
equipment.
Your attention is drawn to, for GB: Guidance G24.2 and
recommendation R24.2 of the Water Regulations Guide.
for IE: the current edition of I.S. 813 “Domestic Gas
Installations”.
5. MAKE UP SYSTEM - A method of replacing water
lost from the system should be provided either by
means of a make up vessel of not more than 3 litres (5
pints) capacity, mounted above the highest point of the
system, or by re-pressurisation of the system.
6. VENTING - A method of venting the system during
filling and commissioning must be provided by fitting
automatic air vents or by venting manually.
Stop
Valve
Fig. 14
© Baxi Heating UK Ltd 2014
Cold
Mains
Inlet
Double
Check
Valve
Temporary
Hose
7. HOT WATER STORAGE - The hot water storage
vessel must be of the indirect coil type. All components
used in the system must be suitable for operation at
110°C (230°F) and at the pressure allowed by the safety
valve.
Stop
Valve
CH
Return
15
7.0 Site Requirements
7.1
Location
NOTE: Due to the high efficiency of the boiler a
plume of water vapour will be discharged from the
flue. This should be taken into account when siting
the flue terminal.
1. The boiler may be fitted to any suitable wall with the
flue passing through an outside wall or roof and
discharging to atmosphere in a position permitting
satisfactory removal of combustion products and
providing an adequate air supply. The boiler should be
fitted within the building unless otherwise protected by a
suitable enclosure i.e. garage or outhouse. (The boiler
may be fitted inside a cupboard - see Section 7.2).
Zone 2
Window
Recess
Zone 1
Zone 2
Zone 0
2. If the boiler is sited in an unheated enclosure then it is
recommended to incorporate an appropriate device for
frost protection in the system controls.
0.6 m
Window
Recess
3. If the boiler is fitted in a room containing a bath or
shower it MUST NOT BE fitted in zone 0, 1 or 2, ONLY
within the shaded area (Figs. A & B shows zone
dimensions for a bathtub. For other examples refer to
the Current I.E.E. Wiring Regulations) reference must be
made to the relevant requirements.
In GB this is the current I.E.E. Wiring Regulations and
Building Regulations.
In IE reference should be made to the current edition of
I.S. 813 “Domestic Gas Installations” and the current
ETCI rules.
Zone 2
Fig. A
In GB Only
Ceiling
Window Recess
Zone 2
Outside Zones
4. If the boiler is to be fitted into a building of timber
frame construction then reference must be made to the
current edition of Institute of Gas Engineers Publication
IGE/UP/7 (Gas Installations in Timber Framed Housing).
7.2
Zone 1
Zone 2
2.25 m
Zone 0
0.6 m
Fig. B
In GB Only
Ventilation of Compartments
1. Where the boiler is installed in a cupboard or
compartment, no air vents are required for cooling
purposes providing that the minimum dimensions below
are maintained.
Sides
15mm
Top
200mm
Bottom
50mm
Front
30mm
2. If the boiler is installed in a smaller cupboard or
compartment it must be ventilated according to
BS 5440 Part 2 and the minimum clearances given in
section 4.0 “Technical Data” maintained.
3. Any compartment should be large enough to house
the boiler only.
NOTE: The ventilation label on the front of the outer
case MUST NOT BE REMOVED when the appliance is
installed in a compartment or cupboard.
16
© Baxi Heating UK Ltd 2014
390mm
5mm Min
5mm Min
7.0 Site Requirements
7.3
200mm
Clearances (Figs. 15 &16)
1. A flat vertical area is required for the installation of the
boiler.
2. These dimensions include the necessary clearances
around the boiler for case removal, spanner access and air
movement. Additional clearances may be required for the
passage of pipes around local obstructions such as joists
running parallel to the front face of the boiler.
600mm
3. For unventilated compartments see Section 7.2.
7.4
Gas Supply
1. The gas installation should be in accordance with the
relevant standards. In GB this is BS 6891. In IE this is the
current edition of I.S. 813 “Domestic Gas Installations”.
50mm
Fig. 15
2. The connection to the appliance is a 1/2in BSPF.
3. Ensure that the pipework from the meter to the
appliance is of adequate size to ensure correct operation.
Do not use pipes of a smaller diameter than the boiler
gas connection.
7.5
At Least 1.5°
Electrical Supply
1. External wiring must be correctly earthed, polarised and
in accordance with relevant regulations/rules. In GB this is
the current I.E.E. Wiring Regulations. In IE reference
should be made to the current edition of ETCI rules.
2. The mains supply is 230V ~ 50Hz fused at 3A.
NOTE: “The method of connection to the electricity
supply must facilitate complete electrical isolation of the
appliance”.
500mm
For Servicing
Purposes
Note! There is no method of isolating the boiler, at the
user interface.
Connection may be via a fused double-pole isolator with a
contact separation of at least 3mm in all poles and servicing
the boiler and system controls only.
5mm
Fig. 16
280mm
WARNING: The PCB Control and Fan
Assembly are 325 Vdc. Isolate at supply
before access.
In Operation
© Baxi Heating UK Ltd 2014
17
Examples are shown of the following methods of termination:i) to an internal soil & vent pipe
ii) via an internal discharge branch (e.g. sink waste) downstream of the trap
iii) to a drain or gully
iv) to a purpose made soakaway
v) pumped into an internal discharge branch (e.g. sink waste) downstream of the trap
vi) pumped into an external soil & vent pipe
vii) to a drain or gully with extended external run & trace heating
It is strongly recommended to discharge internally into the household
drainage system. If connecting to a rain water drain, that drain MUST
discharge into a foul drain.
Insulation
32mm
21.5mm
i) Termination to an internal soil and
vent pipe
50mm
2.5° M
per me
inimum
tre of
fall
n
*450mm is applicable to properties
up to 3 storeys.
For multi-storey building installations
consult BS 6798.
Sink
ii) External termination via internal discharge branch
e.g sink waste - downstream*
50mm
per me
tre of
2.5° M
inimum
pipe ru
n
fall
Pipe must terminate above
water level but below
surrounding surface. Cut
end at 45°
*It is NOT RECOMMENDED
to connect upstream of the
sink or other waste water
receptacle !
Boiler
iii) Termination to a drain or gully
50mm
per me
tre of
2.5° M
inimum
pipe ru
n
7.6
Condensate Drain
FAILURE TO INSTALL THE CONDENSATE DISCHARGE
PIPEWORK CORRECTLY WILL AFFECT THE RELIABLE
OPERATION OF THE BOILER.
CAREFUL CONSIDERATION MUST BE GIVEN TO THE
POSSIBILITY OF THE PIPEWORK BEING SUBJECT TO
FREEZING CONDITIONS AND APPROPRIATE
MEASURES TAKEN TO PREVENT BLOCKAGE.
CORRECT INSTALLATION IN ACCORDANCE WITH
THIS SECTION WILL CONSIDERABLY MINIMISE THE
LIKELIHOOD OF BLOCKAGE AND SUBSEQUENT
BOILER LOCK-OUT.
A CONDENSATE DISCHARGE PUMP AND PIPE ‘TRACE
HEATING’ ARE AVAILABLE AS ACCESSORIES - see
paragraphs 7.7.12 to 7.715 for further details.
The condensate discharge pipe MUST NOT RISE at any
point along its length. There MUST be a fall of AT LEAST
2.5° (50mm per metre) along the entire run EXCEPT when
employing a suitable condensate pump in basement and
cellar or similar applications.
pipe ru
450mm min*
Boiler
7.0 Site Requirements
Pipe must terminate above
water level but below
surrounding surface. Cut
end at 45°
fall
The boiler condensate trap incorporates a seal of 75mm,
therefore it is unnecessary to install an air break and trap in
the discharge pipework.
1. The condensate outlet will accept 21.5mm (3/4in) plastic
overflow pipe. It is strongly recommended that this discharges
internally into the household drainage system.
Where this is not possible, discharge into an outside drain is
permissible providing every possible precaution is taken to
prevent freezing.
2. Ensure the discharge of condensate complies with any
national or local regulations in force. BS 6798 & Part H1 of the
Building Regulations give further detailed guidance.
3. The discharge pipe should be run in a proprietary drain pipe
material e.g. PVC, PVC-U, ABS, PVC-C or PP.
4. Metal pipework is NOT suitable for use in condensate
discharge systems.
5. The pipe should be a minimum of 21.5mm diameter and
must be supported using suitably spaced clips of the correct
design to prevent sagging.
6. It is advisable that the full length of condensate pipe is run
internally and preferably be less than 3 metres.
7. Internal runs greater than 3 metres or runs in cold areas
should use 32mm waste pipe.
8. External runs MUST be a MINIMUM of 32mm and fully
insulated with material suitable for external use.
iv) Termination to a purpose made soakaway
Further specific requirements for soakaway
design are referred to in BS 6798.
Boiler
500mm min
50mm p
er metr
e of pip
2.5° Min
imum fa
e run
18
ll
Holes in the soak-away must
face away from the building
9. If the boiler is fitted in an unheated location the entire
condensate discharge pipe should be treated as an external run
and sized and insulated accordingly.
10. In all cases discharge pipe must be installed to aid disposal of
the condensate. To reduce the risk of condensate being
trapped, as few bends and fittings as possible should be used
and any burrs on cut pipe removed.
11. When discharging condensate into a soil stack or waste pipe
the effects of existing plumbing must be considered. If soil pipes
or waste pipes are subjected to internal pressure fluctuations
when WC's are flushed or sinks emptied then back-pressure
may force water out of the boiler trap and cause appliance
lockout.
© Baxi Heating UK Ltd 2014
v) pumped into an internal discharge branch
(e.g. sink waste) downstream of the trap
Sink
50mm
7.0 Site Requirements
per me
tre of p
ipe run
2.5° M
inimum
fall
Pipe must terminate above
water level but below
surrounding surface. Cut
end at 45°
7.6
Condensate Drain (cont.)
12. A boiler discharge pump is available, ‘MULTIFIT’
part no. 720648301. This pump will dispose of both
condensate & high temperature water from the relief valve.
It has a maximum head of 5 metres. Follow the instructions
supplied with the pump.
13. Condensate Drain Pipe ‘Trace Heating’ Elements are
available in various lengths. ‘MULTIFIT’ part nos.:-
Basement or similar
(heated)
1 metre 720644401
2 metre 720664101
3 metre 720664201
5 metre 720664401*
Boiler
*Where the drain is between 3 & 5 metres a 5 metre kit can
be used and “doubled back” upon itself.
14. It is possible to fit the element externally on the
condensate drain or internally as detailed in the instructions
provided.
Condensate Pump
15. The fitting of a ‘Trace Heating’ Element is NOT a
substitute for correct installation of the condensate drain.
ALL requirements in this section must still be adhered to.
vi) pumped into an external soil & vent pipe
50mm
Unheated Location
(e.g. Garage)
per me
tre of p
ipe run
2.5° M
inimum
fall
Basement or similar
(heated)
vii) to a drain or gully with extended
external run & trace heating
Boiler
The ‘Trace Heating’ element
must be installed in accordance
with the instructions supplied.
External runs & those in
unheated locations still require
insulation.
Boiler
Condensate Pump
50mm
per me
tre of
2.5° M
inimum
© Baxi Heating UK Ltd 2014
pipe ru
n
fall
Pipe must terminate above
water level but below
surrounding surface. Cut
end at 45°
19
Terminal Position with Minimum Distance (Fig. 17)
(mm)
7.0 Site Requirements
A1 Directly below an opening, air brick, opening
windows, etc.
300
B1 Above an opening, air brick, opening window etc.
300
C1 Horizontally to an opening, air brick, opening window etc.
300
D2 Below gutters, soil pipes or drain pipes.
25 (75)
E2 Below eaves.
25 (200)
F2 Below balconies or car port roof.
25 (200)
G2 From a vertical drain pipe or soil pipe.
25 (150)
(i) 25 (300) (ii) 115
H From an internal (i) or external (ii) corner.
I
Above ground, roof or balcony level.
300
J
From a surface or boundary line facing a terminal.
600
K From a terminal facing a terminal (Horizontal flue).
1200
From a terminal facing a terminal (Vertical flue).
600
L From an opening in carport (e.g. door, window)
into the dwelling.
1200
M Vertically from a terminal on the same wall.
1500
N Horizontally from a terminal on the same wall.
300
R From adjacent wall to flue (vertical only).
300
S From an adjacent opening window (vertical only).
1000
T Adjacent to windows or openings on pitched and flat roofs.
600
U Below windows or openings on pitched roofs.
2000
7.7
Flue
NOTE: Due to the high efficiency of the boiler a plume of
water vapour will be discharged from the flue. This should
be taken into account when siting the flue terminal.
1. The following guidelines indicate the general requirements
for siting balanced flue terminals. For GB recommendations are
given in BS 5440 Pt.1. For IE recommendations are given in the
current edition of I.S. 813 “Domestic Gas Installations”.
2. If the terminal discharges onto a pathway or passageway,
check that combustion products will not cause a nuisance and
that the terminal will not obstruct the passageway.
3. Take into consideration the effect the plume of vapour may
have on neighbours when siting the flue.
1 In addition, the terminal should be no nearer than 150 mm to an opening in the
4. Adjacent surfaces close to the flue terminal may need
protection from the effects of condensation. Alternatively a flue
deflector kit (part no. 248167) is available.
building fabric formed for the purpose of accommodating a built-in element such as
a window frame.
2 Only ONE 25mm clearance is allowed per installation. If one of the dimensions
5. For installation of the flue into an internal corner at the
25mm dimension the flue deflector kit (part no. 248167) must
be fitted.
Table. 2
D, E, F, G or H is 25mm then the remainder MUST be as shown in brackets, in
accordance with B.S.5440-1.
NOTE: The distance from a fanned draught appliance terminal
installed parallel to a boundary may not be less than 300mm in
accordance with the diagram below
300 min
Terminal
Assembly
*
6. * Reduction to the boundary is possible down to 25mm but
the Flue Deflector Kit (part no. 248167) must be fitted.
7. If required a suitable terminal guard is available from Baxi for
use with the flue deflector.
8. For fitting under low soffits and eaves the Plume
Displacement Kit or Flue Deflector Kit is recommended.
9. If a terminal is less than 2 metres (783/4 in) above a balcony,
above ground or above a flat roof to which people have access,
then a suitable terminal guard must be provided.
IMPORTANT:
• Under car ports we recommend the use of the plume
displacement kit.
• The terminal position must ensure the safe and
nuisance - free dispersal of combustion products.
Top View Rear Flue
Fig. 17a
Property Boundary Line
J,K
IMPORTANT: If fitting a Plume
Displacement Flue Kit, the air inlet
must be a minimum of 150mm from
any opening windows or doors (see
Section 9.0).
T
U
Plume
Displacement Kit
N
R
M
I
D
E
C
I
A
I
F
S
I
F
J,K
B
L
G
A
A
H
H
Air Inlet
I
Likely flue positions requiring
a flue terminal guard
20
© Baxi Heating UK Ltd 2014
Fig. 17
Opening Window
or Door
Fig. 17b
150mm
MIN.
8.0 Flue Options
8.1
Y
X
Horizontal Flue Systems
Concentric
The maximum equivalent lengths are 4m (horizontal) or
(vertical). Their lengths exclude the standard elbow and
flue/terminal assembly (horizontal) and terminal assembly
(vertical).
Any additional “in line” bends in the flue system must be
taken into consideration. Their equivalent lengths are:
Horizontal
Flue System Examples
Concentric Pipes:
45° bend
93° bend
0.5 m
1.0 m
NOTE: Flue length is measured from point X to Y as
shown.
Y
X
IMPORTANT: All flue systems must be securely
supported at least once every metre. Suitable pipe
supports are available as accessories.
Plume Displacement 70/110 dia Kit
1M Extensions, 45° & 93° bends
are also available - see Section 9.0
NOTE: Horizontal flue pipes should always be installed with a 1.5° fall from the
terminal to allow condensate to run back to the boiler.
This bend is equivalent to
0.5 metre
B
A
Y
X
This bend is equivalent to
0.5 metre
Total equivalent length (up to 4m) =
A+B+2x45°Bends
© Baxi Heating UK Ltd 2014
21
Vertical Flue System
Examples (Twin Pipe)
8.0 Flue Options
8.2
Twin & Vertical Flue Systems
Concentric
The maximum equivalent lengths are 4m (vertical). Their
lengths exclude the standard elbow and terminal assembly
(vertical).
Y
Twin Flue
The total maximum equivalent flue length is 150m.
NOTE: Each 1m of flue duct should be calculated as 2m.
X
Any additional “in line” bends in the flue system must be
taken into consideration. Their equivalent lengths are:
Vertical Flue
System Examples
Concentric Pipes:
135° bend
93° bend
0.5 m
1.0 m
Twin Flue Pipe:
135° bend (air duct)
135° bend (flue duct)
90° bend (air duct)
90° bend (flue duct)
1.3 m
2.6 m
4.8 m
9.6 m
Y
IMPORTANT: All flue systems must be securely
supported at least once every metre. Suitable pipe
supports are available as accessories.
X
Total Equivalent Length =
A+B+C+1x90°Bend
Roof
Terminal
All vertical and angled runs must be included,
measured from the boiler adaptor (point X) to the
joint with the flue terminal (point Y). One 91.5°
bend or two 135° bends can be included without
reduction of the flue length.
The total equivalent length
for this example is
17.2 + 34.4 = 51.6 metres.
If further elbows are required the flue length must
be reduced by the following amounts:-
Y
1 metre for each 91.5° bend
0.5 metre for each 135° bend
C
B
Equivalent
Length Value
1m extension
135°bend
91.5°bend
This bend is equivalent to
1 metre
5
2
2
Sub total
5.0m
2.6m
9.6m
Equivalent Length Air Duct = 17.2m
A
X
1m
1.3m
4.8m
AIR DUCT
No of
fittings/pipes
Equivalent
Length Value
1m extension
135°bend
91.5°bend
2m
2.6m
9.6m
FLUE DUCT
No of
fittings/pipes
5
2
2
Sub total
10.0m
5.2m
19.2m
Equivalent Length Flue Duct = 34.4m
22
© Baxi Heating UK Ltd 2014
8.0 Flue Options
8.3
Key Accessory
Size
FLUE GROUP B
Concentric Flue System 110mm diameter
A1
Horizontal Flue Terminal
850mm
A
Horizontal Flue Terminal (incl elbow)
B
Flue Extension
1000mm
500mm
250mm
C
Flue Bend
93°
D
Flue Bend (pair)
135°
U
Pipe Support
110mm
T
Vertical Flue Boiler Adaptor
S
Flue Terminal Deflector
B
A1
A
E
T
K
FLUE GROUP P
Twin Flue System 80mm diameter
E
Flue Extension
F
G
J
W
S
D
C
Flue Accessories
Flue Bend (pair)
Flue Bend (2 pair)
Vertical Flue Boiler Adaptor Kit
Pipe Support (pair)
80mm
FLUE GROUP B,P
Vertical Flue Kits
K
Vertical Flue Terminal
L
Pitched Roof Flashing
M
Roof Cover Plate
N
Flat Roof Flashing
G
F
1000mm
500mm
250mm
90°
135°
25°/50°
Code No
243013BAX
236921
241695
241694
241692
241687
241689
243014BAX
5106888
248167
246137
246136
246135
5121560
5121561
242757
5111081
242802
243015
243131
243016BAX
U,W
M
L
N
J
© Baxi Heating UK Ltd 2014
23
8.0 Flue Options
For Vertical Flues
8.4
Vertical Flue
Adaptor
For Vertical Flue Systems
1. Undo the screws securing the blanking plate to the
boiler top panel. Discard the plate.
Gasket
2. Fix the vertical adaptor and gasket to the top panel with
the previously removed screws.
8.5
For Twin Flue Systems
1. Undo the screws securing the blanking plate to the
boiler top panel. Discard the plate.
2. Fix both the air and flue adaptors with their gaskets
onto the boiler top panel. Secure with screws.
For Twin Flues
Air Duct
Adaptor
Gasket
Flue Duct
Adaptor
Gasket
24
© Baxi Heating UK Ltd 2014
8.0 Flue Options
8.6
1. In the case of a pitched roof 25 - 50 degrees, position
the lead tile to replace/flash over existing roof tiling. Make
an aperture in the roof suitable for the lower tube of the
roof terminal and ensure the integrity of the roof cover is
maintained. The adjustable plastic collar can either be
positioned on the lead tile or the lower tube of the roof
terminal prior to the final positioning of the vertical flue
through the tile. Check the collar is correctly located to suit
required roof pitch (either 25° to 38° or 37° to 50°). From
inside the roof adjust the flue to a vertical position and
secure to the roof structure with the clamp supplied.
Approx
1425mm
Cut the same
amount off the
Air Duct &
Flue Duct
2. For flat roof installations the aluminium flashing must be
incorporated into the roof covering and the appropriate
aperture made in the roof decking. The vertical flue is
lowered onto the flashing making sure the collar of the flue
locates securely with the flashing. (A mastic seal may be
necessary). From inside the roof, adjust the flue to a vertical
position and secure to the roof structure with the clamp
supplied.
Air Duct
Flue Duct
Push Fit Adaptor
IMPORTANT: If the boiler is not fitted immediately
after the flue system, temporary precautions must be
taken to prevent rain entry into the room of installation.
Any precautionary measures must be removed prior to
commissioning the boiler.
8.7
m
0m
80
Flue Dimensions
The standard horizontal flue kit allows for flue lengths
between 270mm (105/8”) and 800mm (32”) from elbow to
terminal (Fig. 18).
m
0m
27
For Roof Terminals
Flue Deflector
The maximum permissible equivalent flue length is: 4
metres.
NOTE: Each additional 45° of flue bend will account
for an equivalent flue length of 0.5m.
e.g. 45° = 0.5m,
90° = 2 x 45° = 1m etc.
Fig. 18
Fig. 18a
8.8
Terminal Guard (Fig. 19)
1. When codes of practice dictate the use of terminal
guards, they can be obtained from most Plumbers’ and
Builders’ Merchants.
2. When ordering a terminal guard, quote the appliance
model number.
3. The flue terminal guard should be positioned centrally
over the terminal and fixed as illustrated.
8.9
Fig. 19
© Baxi Heating UK Ltd 2014
Flue Deflector (Fig. 18a)
1. If required, push the flue deflector over the terminal end
and rotate to the optimum angle for deflecting plume.
Secure the deflector to the terminal with screws provided.
25
9.0 Plume Displacement
Plume Outlet (‘Peak’
MUST be Uppermost)
9.1
Plume Displacement Kit (P.D.K.)
Kit No 5121371
Content of kit
1 70/110 Concentric Flue
1 1m 70 Dia Exhaust Flue Pipe
2 Support Brackets
1 93° Elbow/Plume Outlet Assembly
1 Flue Trim
2 “O” Rings
1 Elbow with Gasket
0.94 metre
1. This kit is recommended for installations where the
condensate plume emitted from the flue may cause a nuisance
or affect the surroundings.
2. The terminal must be positioned outside the building with
the outlet connection upwards.
3. The 70Ø pipe connects to the outlet of the concentric
terminal assembly. The elbow/plume outlet must be fitted to
the end of the 70Ø pipe.
NOTE: The plume outlet must always be at least 45° to
the wall, with the ‘peak’ uppermost to prevent rain entry
(Figs. A & B), and be at least 2 metres above ground level.
It must be secured as shown in Fig. C.
The outlet must be positioned so that any condensate
plume is directed away from adjacent surfaces.
Fig. C
45°
45°
Outlet must be
at least 45° from
wall face
4. It is possible to reduce or increase (with the addition of
extensions) the length of either or both the 70/110 concentric
and 70Ø exhaust.
‘Peak’ MUST be
Uppermost
5. Standard concentric flue extension kits may be added
between the boiler elbow and the terminal assembly.
6. The minimum length of the concentric flue is 100mm when
measured from the edge of the boiler flue elbow. There is a
further 45mm engagement into the elbow.
IMPORTANT: The maximum equivalent length of
concentric flue is:- 4 metres
Additional elbows may be fitted in the concentric flue, but
the equivalent length must be reduced by 1 metre (93°
elbow) or 0.5 metres (45° elbow).
500mm Min.
NOTE: Permitted positions of the plume outlet relative to
doors, windows etc. are the same as for conventional
concentric flues as detailed in the main Installation &
Servicing Instructions and BS5440 Pt. 1. It is NOT
necessary to fit a terminal guard over the air inlet or the
plume outlet.
Fig. A
Outlet Connection
upwards
26
Fig. B
© Baxi Heating UK Ltd 2014
7. 70Ø 1 metre extensions (including support bracket), and
additional 93° & 45° elbows are available. Any additional 93°
& 45° elbows must be accounted for when calculating flue
lengths. 70Ø 93° elbows are equivalent to 3.5 metres of
straight length and 45° elbows to 1 metre.
30
30
28
28
26
26
20
20
70Ø Exhaust (metres)
70Ø Exhaust (metres)
10
16
4
12
14
12
10
8
8
6
6
4
4
2
2
0
Example 1 - Not Permissible
If, for instance, a concentric length of 3.25 metres was
required and the 70Ø exhaust needed to be 10 metres the
graph shows that this combination would NOT be
permissible as the intersection point would be above the
solid diagonal line.
0
0
1
2
3
4
1
0
Concentric 70/110 Flue (metres)
2
3
4
Concentric 70/110 Flue (metres)
Example 1
Flue Lengths - Not Permissible
Determining Permissible Lengths - P.D.K.
In the graph the solid line diagonal represents the
relationship between the concentric flue assembly (and any
extensions) and the 70Ø exhaust (and any extensions or
additional bends).
&2
4
14
18
&2
16
9.2
18
18
18
15,
24
22
15,
24
22
9.0 Plume Displacement
Example 2
Flue Lengths - OK
30
Example 2 - Flue Lengths OK
Where both lengths have been determined they can be
applied to the graph to check that the installation is
permissible. For example, if it was known that 2 metres of
concentric flue and 4 metres of 70Ø exhaust were required,
the values could be applied to the graph as shown in
Example 2.. As the point of intersection of the dotted lines is
below the solid diagonal line, the combination of lengths is
shown to be acceptable.
28
26
24
22
15,
20
&2
16
4
70Ø Exhaust (metres)
18
18
14
12
10
8
6
4
2
0
1
0
2
3
4
Concentric 70/110 Flue (metres)
Example 3
Flue Lengths - OK
Support
Bracket
70Ø Exhaust
Example 3 - Flue Lengths OK
In the example shown, assume that the concentric part of
the flue needs to be 2 metres long. Find the position of ‘2’ on
the horizontal axis of the graph and then project upwards to
the solid diagonal line. This is represented by the vertical
thick dotted line. Where this dotted line intersects with the
solid diagonal line on the graph, project across to the vertical
axis. As can be seen this corresponds with 14 metres.
Therefore, the total equivalent length of the 70Ø exhaust
can be up to 14 metres. Any elbow equivalencies must be
accounted for i.e. 93° elbows are equal to 1 metre, each 45°
elbow to 0.5 metres.
45° Elbow
Flue Length - Worked Example
Gold H 24
X
93° Elbow
Y
1 metre Extension
1 metre supplied in kit
Concentric 70/110 Flue
(MUST be installed
horizontally)
Concentric Flue
To calculate total length:Length of 70Ø supplied in kit =
3 x 1 metre Extensions =
1 x 93° Elbow =
2 x 45° Elbow =
1 metre
3 metres
1 metre
1 metre (0.5 metres each)
Total 70Ø =
6 metres
After consulting the table in Example 3 it can be determined
that the concentric flue could be up to approximately 3.25
metres long.
Additional Accessories
A - 93° Elbow
B - 45° Elbow (Pair)
C - 1 metre 70Ø Extension
In Fig. D opposite an additional 93° elbow and pair of 45°
elbows have been included in the 70Ø exhaust.
Also 3 straight extension pieces have been used.
5121373
5121374
5121372
Fig. D
© Baxi Heating UK Ltd 2014
27
9.0 Plume Displacement
9.3
This section of the
flue MUST be
horizontal
Min. 2 metres
General Fitting Notes - P.D.K.
1. Cut a hole in the external wall which the horizontal
concentric flue assembly will pass through.
2. When completed the terminal must be at least 2 metres
above ground level (Fig. E).
3. Measure and cut to size the concentric assembly and any
extensions that are being used.
4. Insert the concentric assembly through the hole from
outside the building and mark the position of the flue trim
securing holes.
Min. 0.3 metres
5. Drill and plug the wall to accept the flue trim securing
screws, and re-insert the concentric assembly through the
wall.
6. Connect any extensions that are being used to the
concentric assembly. Engage the extension or concentric
assembly in the boiler flue elbow.
7. Fit the boiler flue elbow to the boiler top panel, ensuring
the gasket is in place (Fig. F).
Fig. E
Ensure that the concentric assembly is horizontal and
that the external air inlet is to the bottom. Any
extensions should fall back to the boiler.
8. Use suitable brackets to support the concentric assembly
and any extensions, and make good inside and outside.
Secure the flue trim to the wall.
9. The 70Ø exhaust can now be fitted to the spigot at the
terminal end.
Fig. F
10. If it is necessary to shorten the 70Ø exhaust or any of
the extensions, the excess material must be cut from the
plain end of the pipe.
11. Determine the position of the 70Ø exhaust and mark
on the wall a suitable position for the support bracket. Drill
and plug the wall. If extensions are being used, a support
bracket is supplied in each kit.
12. Engage the M6 threaded part of the mounting bolt in
the boss on the support bracket. Using the bracket for
leverage, screw the mounting bolt into the plugged hole
until the bracket is secure and level (Fig. G).
13. Slacken the two screws securing the retaining strap to
the bracket, and pivot the strap aside to allow fitting the
70Ø exhaust.
Fig. G
14. Complete the installation of the 70Ø exhaust, securing
in the brackets. Fit the 93° elbow and plume outlet. Ensure
the plume outlet is at least 45° to the wall and that the
‘peak’ is uppermost.
15. Continue with installation and commissioning of the
boiler.
28
© Baxi Heating UK Ltd 2014
9.0 Plume Displacement
Plume Outlet
Elbow
9.3
General Fitting Notes - P.D.K. (cont.)
16. For aesthetic purposes it is permissible to route the
70Ø exhaust in an enclosed box, but the air inlet and
plume outlet MUST remain in free air.
500
mm
Min
.
Fig. H
17. It is also possible to separate the plume outlet from
the 93° elbow to allow the flue to be installed as shown
in Fig. H.
18. When the plume outlet is positioned under a balcony
or other projection (Figs. I & J) it must protrude at least
200mm (it is not necessary to extend it further than this).
200mm Min.
Fig. I
200mm Min.
Fig. J
© Baxi Heating UK Ltd 2014
29
Template
Literature Pack
10.0 Installation
Wall Plate
Check Site Requirements (section 7) before
commencing.
10.1
The gas supply, gas type and pressure must be
checked for suitability before connection (see Section
7.4).
Fig. 19a
Edge of Boiler
1. Cut the banding and remove the fixing template, wall
plate and literature pack (Fig. 19a) from the carton.
Example
2m
96mm
Example
V = 55mm
EXAMPLE: Boiler is 2 metres away
from corner of wall, flue duct hole is
55mm up from horizontal side flue
centre line. This will maintain the
approx 1.5° backfall to the boiler.
Horizontal
Side Flue
Centre Line
Wall Thickness
Flue Hole ø
up to 227mm
127mm core drill
up to 750mm
150mm core drill
up to 1200mm
175mm core drill
Fig. 20
Backfall to the Boiler, ie. 2m flue offset (V) position 55mm
13.5
2. After considering the site requirements (see Section
7.0) position the template on the wall ensuring it is level
both horizontally and vertically.
NOTE: When fitting Plume Displacement Kit refer
to the instructions supplied for details of
installation of the flue.
3. Mark the position of the fixing holes for the wall
plate (Fig. 20).
Wall Plate Template
Flue Duct Hole
Offset V (mm)
Initial Preparation
27.5
55
82.5
110 (mm)
1.5°
V
4. Mark the centre of the flue hole (rear exit).
For side exit: project the horizontal side flue centre line
into the corner of the room and along the wall to
where the flue hole will be drilled. (Fig. 20).
The diagram (Fig. 21) shows the dimensions required to
ensure any horizontal flue is installed with the correct
fall to the boiler. Mark the offset (V) dimension and if
required, mark the position of the gas and water pipes.
Remove the template.
5. Cut the hole for the flue (minimum diameter
127mm, see table (Fig. 20) for wall thicknesses and flue
diameters).
6. Drill and plug the wall as previously marked. Secure
the wall plate (Fig. 22).
0.5
1.0
2.0
3.0
4.0
(metres)
Distance in metres from boiler to the wall.
For pipe lengths greater than 4m increase the off-set by 26mm
for every additional metre to maintain approx 1.5° inclination.
7. Ensuring the wall plate is level both horizontally and
vertically, drill and plug at least 5 securing positions at
the top and bottom through the wall plate. Utilising the
slots available ensure the wall plate is square and secure
to the wall (Fig. 22).
8. Additionally drill 2 relief holes 10mm deep in the wall
as shown on template (Fig. 22).
Fig. 21
8. Loosely route the condensate discharge pipe to the
lower left hand side of the wall plate.
Relief Holes
Wall Plate
30
Fig. 22
© Baxi Heating UK Ltd 2014
10.0 Installation
10.2
Preparing The Boiler
1. Remove the outer carton and packaging.
2. Lift the outercase upwards and remove.
3. Remove the internal packaging.
Fig. 22a
Internal Polystyrene
Packaging Piece
Lower Door Panel
Outercase
Break Off Upper &
Lower Pipe Run
Options
Fig. 23
© Baxi Heating UK Ltd 2014
31
10.0 Installation
10.3
Retaining Bracket
Fitting The Boiler (Fig. 24)
1. Obtain retaining bracket and two M6 nuts from fitting
bag.
2. Offer up the boiler to the wall plate using the lifting
points shown in Fig. 24 and locate the rear bottom edge
onto the self locating support at the base of the wall plate.
(See Safe Manual Handling page 5.)
NOTE: When installing in a Loft/Small Compartment,
access for lifting the boiler from the front can be
gained for two people using the lifting points. (Fig. 24).
Remove the red pipe
protection caps
3. Rotate the boiler up to wall plate and engage retaining
bracket, securing with the two nuts.
4. Ensure the boiler is secured with the retaining
bracket.
5. Remove red pipe protection caps from the FLOW and
RETURN connections.
Fig. 24
Wall Plate
10.4
Making the Water Connections
(Fig. 25)
Return Pipe Connection
1. The boiler has two side water connections which are
labelled FLOW and RETURN. The front connection is the
flow pipe and the rear threaded connection is the return.
Suggested Lifting
Points shown as
shaded area
2. It is essential that the flow and return pipes are
connected to the boiler correctly. The flow connection
incorporates the boiler thermostats and a flow switch.
Flue Products Exhaust
3. The boiler connections will accept 22mm fittings.
Flow Pipe
Connection
Fig. 25
4. If the installation requires that the system pipework
originates from the bottom of the boiler, then the flow
and return pipes will need cutting, as they terminate
upwards.
10.5
Making the Condensate Drain Connection
1. Connect the condensate drain using the 1”BSP nut and
seal supplied. (see section 7.6).
Fig. 25a
32
© Baxi Heating UK Ltd 2014
NOTE: To ensure the correct operation and
integrity of the condensate drainage system Carefully pour approximately 1 cupful (250ml) of
water into the flue products exhaust, at the top of the
heat exchanger (Fig. 25a) to ensure a seal is made in
the trap.
10.0 Installation
Wall Thickness
10.6
Making the Gas Connection
1. Connect the gas supply to the G1/2 (1/2in BSPT
Internal) gas tap. This is located on the lower right side
of the boiler, access by hinging down the PCB housing
(see Fig. 32).
At Least 1.5°
10.7
Fitting The Flue
Before fitting the flue, check the condensate drain
integrity (see section 10.5).
IMPORTANT: The flue should always be installed
with at least 1.5° fall from terminal to elbow, to
allow condensate to run back to the boiler.
HORIZONTAL FLUE
360° Orientation
1. The standard flue is suitable for lengths 270mm
minimum to 800mm maximum (measured from the
edge of the flue elbow outlet).
Rear Flue: maximum wall thickness - 630mm
Side Flue: maximum wall thickness - 565mm (left or right)
(Z)
Edge of Wall Plate to Wall
Wall Thickness
2. For rear exit - measure the wall thickness
(Fig. 26) and to this dimension add 181mm. This
dimension to be known as (X).
i.e.
(X) = wall thickness + 181
3. Take the flue and mark off (X) from the terminal end
as indicated in the diagram (Fig. 27).
Check your dimensions.
Fig. 26
Waste
Fig. 27
The flue tubes are fixed together. Cut through both
tubes whilst resting the flue on the semi-circular packing
pieces. Deburr both tube ends.
(Z) = Side Exit
(X) = Rear Exit
4. For side exit - measure the distance from the edge
of the wall plate to the inner face of the wall (Fig. 26)
and to this dimension add the wall thickness + 250mm.
This dimension to be known as (Z).
i.e.
(Z) = wall plate to wall + wall thickness + 250
Flue
5. Take the flue and mark off (Z) from the terminal end
as indicated (Fig. 27).
Check your dimensions.
The flue tubes are fixed together. Cut through both
tubes whilst resting the flue on the semi-circular packing
pieces. Deburr both tube ends.
Inner Flue Support Bracket
IMPORTANT: Check all measurements before
cutting.
Fig. 27a
© Baxi Heating UK Ltd 2014
NOTE: When cutting ensure the cut does not
interfere with the inner flue support bracket
(Fig. 27a).
33
10.0 Installation
10.7
Inner Flue Support Bracket
Fitting the Flue (Cont)
6. Ensure the inner flue support bracket is positioned in
the flue (Fig. 28).
7. Engage the flue into the flue elbow using soap solution
to ease the engagement ensuring the flue is assembled as
shown (Fig. 29). Rear flue only:- Take the tape supplied
in the kit and wrap around the joint between the flue
and the elbow (Fig. 29a).
Fig. 28
8. Place the gasket over the flue exit on the boiler.
Flue
9. Slide the flue assembly through the hole in the wall.
10. Engage the elbow on to the flue connection on top
of the boiler. Secure with the four screws supplied in the
kit.
11. Make good between the wall and air duct outside
the building ensuring the 1.5° drop between the terminal
and elbow.
Tape (Rear Flue Only)
12. The flue trim should be fitted once the installation is
complete and the flue secure (Fig. 30). Apply a suitable
mastic to the inside of the trim and press against the wall
finish, making sure the brickwork is dust free and dry.
Fig. 29a
Flue Elbow
13. If necessary fit a terminal guard (see Section 8.8).
Apply Lubricant for ease of
assembly. Ensure Flue is fully
engaged into Flue Elbow
VERTICAL FLUEING
1. Only use a flue approved with the Gold H range.
Gasket
Fig. 30
Flue Trim
Fig. 29
34
© Baxi Heating UK Ltd 2014
10.0 Installation
10.8
Making The Electrical Connections
WARNING: This appliance must be earthed
1. The electrical connections are on the right hand side of
the unit.
2. Undo the two screws securing the cable clamp and place
to one side (Fig. 31).
3. Route the incoming electrical cable/s through the
grommet in the support bracket. This will prevent damage
to the cable.
4. Lay the cable through the cable clamp to gauge the length
of cable required when it is connected to the 4-way
terminal block.
5. Connect the (S/L), (N) and ( ) wires to the
4-way terminal block (Fig. 33) and refit the cable clamp
(Fig. 31).
6. Check the electrical installation for:earth continuity, short circuits, resistance to earth, correct
polarity and fuse failure.
Fig. 31
Cable Clamp
4-way Terminal Block
S/L
N
P/F
Optional Pump Feed Connection
only required for fully TRV’d system
Fig. 33
© Baxi Heating UK Ltd 2014
35
11.0 Electrical
11.1
Schematic Wiring Diagram
Earths not shown to aid
clarity of diagram
op
PCB
g
op
w g br
b
bk
r
w
r
gy
r
br
g/y
g/y
CH
Flow
Switch
Flow
Thermistor
325 Vdc
DC Fan
op
Flow
Overheat
Thermostat
Gas
Valve
b
bk
Key To Wiring Colours
b - Blue
r - Red
bk - Black
g - Green
w - White
g/y- Green/Yellow
br - Brown
op - Opaque
gy - Grey
y - Yellow
© Baxi Heating UK Ltd 2014
bk
y
br
g/y
L
36
b
r
gy
N Optional
Pump
Feed
bk
Fan
Overheat
Thermostat
w
Flame Spark
Detection Electrode
Electrode
g/y
Condensate
Trap
11.0 Electrical
11.2
Illustrated Wiring Diagram
Optional
Pump
Feed N
L
Flow
Thermistor
y
r
b
g/y
br
r
b
CH
Flow Switch
y
br
g/y
Spark
Electrode
b
Flame
Detection
Electrode
gy
gy
br
br
Main
PCB
w
Layout of PCB Pins
op
br
g
r
b
w
g/y
Condensate Trap
w
r
bk
Gas Valve
bk
Fan Overheat
Thermostat
bk
Fan
bk
Flow Overheat
Thermostat
Wiring Key
b
bk
br
r
w
g/y
g
gy
op
y
© Baxi Heating UK Ltd 2014
- Blue
- Black
- Brown
- Red
- White
- Green/Yellow
- Green
- Grey
- Opaque
- Yellow
37
12.0
12.1
Commissioning the Boiler
Commissioning the Boiler
WARNING: The PCB Control and Fan
Assembly are 325 Vdc. Isolate at supply
before access.
1. Reference should be made to BS:EN 12828 & 14336
when commissioning the boiler.
2. At the time of commissioning, complete all relevant
sections of the Benchmark Checklist at the rear of this
publications.
3. Flush the whole system using a suitable flushing agent
(see Section 6.2) and vent the radiators. Check for water
leaks.
Gas Service
Cock
4. Refill the system with inhibitor following the inhibitor
manufacturer’s instructions and BS 7593 Code of Practice
for Treatment of Water in Domestic Hot Water Central
Heating Systems (see Section 6.2).
5. Complete the label supplied with the inhibitor and
attach to the inside of the boiler case. Detail of system
treatment should be added for future reference.
6. Turn the gas supply on and purge according to in GB
BS 6891 and in IE I.S. 813 “Domestic Gas Installations”.
High
Open
Reset
Fig. 34
Low
Flow Temperature
Adjustment Screw
ON
7. Remove the top RH securing screw and hinge down
the PCB housing to gain access to the gas service cock
(see Fig. 32). Turn the gas service cock anticlockwise to
the ON position and check for gas tightness up to the gas
valve (Fig. 34).
NOTE: The boiler is self-regulating dependent upon
the system load. No adjustment of the gas
valve is permissible.
Fig. 35
8. Having checked:
• That the boiler has been installed in accordance
with these instructions.
• The integrity of the flue system and the flue seals.
• The integrity of the boiler combustion circuit and
the relevant seals.
IMPORTANT: The combustion for this appliance has
been checked, adjusted and preset at the factory for
operation on the gas type specified on the appliance
data plate. However, it is still necessary to check the
combustion as part of commissioning (see Flow Chart
12.2). Do not adjust the air/gas ratio valve.
IN
OUT
DO NOT check gas pressure here
Fig. 36
Inlet Gas Pressure Test Point
38
© Baxi Heating UK Ltd 2014
12.0
Perform Flue Integrity
Visual Check
Examine all flue joints for
soundness and ensure the
system is adequately
supported.
No
Is flue system OK ?
Rectify all faults
If necessary call
0844 871 1555 for advice.
The appliance MUST NOT be
commissioned until all
problems are resolved.
Checking the Combustion
1. This procedure is mandatory in GB from April 2014. It is
strongly recommended to perform the procedure before that
date.
Yes
Set Boiler to Maximum Rate*
Allow the combustion to
stabilise. Do not insert probe
to avoid ‘flooding’ the analyser.
*To operate at Maximum Rate
Ensure all external controls are
calling for heat, that the system
is cold and the boiler control
knob is turned fully clockwise.
Check CO & Combustion
Ratio at Maximum Rate
Whilst the boiler is still
operating at maximum insert
the analyser probe into the
flue gas test point, allowing the
reading to stabilise.
No
Verify Integrity of Seals
Check all burner seals, internal
flue seals, door & case seals.
Replace any seals that appear
unsound.
Is CO < 350ppm
and CO/CO2
ratio < 0.004 ?
Yes
No
TURN APPLIANCE OFF !
Call 0844 871 1555 for advice.
The appliance MUST NOT be
commissioned until all
problems are identified and
resolved.
If commissioning cannot be
fully completed the appliance
must be disconnected from
the gas supply in accordance
with the GSIUR.
Note: Check & record the CO
& combustion ratio at both
maximum & a low rate before
calling 0844 871 1555.
© Baxi Heating UK Ltd 2014
12.2
Commissioning the Boiler
Is CO < 350ppm
and CO/CO2
ratio < 0.004 ?
Yes
Set Boiler to operate at a low
rate. If it is not possible to adjust
the boiler to run at minimum rate
using the boiler controls, the
system must be set such that the
boiler will modulate to as low an
input as possible without the
burner extinguishing (e.g. by
closing radiator valves)
Allow the combustion to
stabilise. Do not insert probe to
avoid ‘flooding’ the analyser.
The gas rate must be checked &
recorded whilst the boiler is
operating in this condition.
No
Is CO < 350ppm
and CO/CO2
ratio < 0.004 ?
Yes
BOILER OPERATING
SATISFACTORILY. NO
FURTHER ACTION
REQUIRED
Ensure test points are capped,
the boiler case front panel is
correctly fitted & secured and
all other commissioning
procedures completed.
Complete the ‘Benchmark’
Checklist, recording the
CO & combustion ratio
readings as required.
39
12.0 Commissioning the Boiler
12.3
Check the Operational (Working) Gas
Inlet Pressure
1. Ensure that all controls are calling for heat and
maximum load is applied to the system.
2. With the boiler operating in the maximum rate
condition check that the operational (working) gas
pressure at the inlet gas pressure test point is in
accordance with B.S. 6798 & B.S. 6891.
3. Ensure that this inlet pressure can be obtained with
all other gas appliances in the property working.
Measure the Gas Rate
4. With any other appliances & pilot lights turned OFF
the gas rate can be measured. It should be as shown in
Section 4.0 Technical Data.
IN
OUT
DO NOT check gas pressure here
Fig. 36a
Inlet Gas Pressure Test Point
40
© Baxi Heating UK Ltd 2014
5. Carefully read and complete all sections of the
Benchmark Commissioning Checklist at the rear of this
publication that are relevant to the boiler and
installation. These details will be required in the event of
any warranty work. The publication must be handed to
the user for safe keeping and each subsequent regular
service visit recorded.
6. For IE, it is necessary to complete a “Declaration of
Conformity” to indicate compliance with I.S. 813. An
example of this is given in I.S. 813 “Domestic Gas
Installations”. This is in addition to the Benchmark
Commissioning Checklist.
13.0
13.1
Break Off Panel
Fitting the Outer Case
Fitting The Outer Case
1. Position the outercase over the boiler engaging the
lugs in the side flanges over the hooks on the wall plate.
Break off top or bottom panel as required to
accommodate pipework runs (Fig.37).
2. Using the two screws supplied in the kit, secure the
outercase to the combustion box (Fig. 37).
3. Hinge up the lower door panel (Fig. 38).
4. The “Important Ventilation Information” label can be
removed unless the appliance is installed in an
unventilated compartment.
5. Carefully read and complete all sections of the
Benchmark Commissioning Checklist at the rear of this
publication that are relevant to the appliance and
installation. These details may be required in the event
of any warranty work. The publication must be handed
to the user for safe keeping and each subsequent
regular service visit recorded.
Fig. 37
For IE, it is necessary to complete a “Declaration of
Conformity” to indicate compliance to I.S. 813. An
example of this is given in I.S. 813 “Domestic Gas
Installations”. This is in addition to the Benchmark
Commissioning Checklist.
Outercase Securing
Screws
6. Instruct the user in the operation of the boiler
controls. Hand over the User’s Operating, Installation
and Servicing Instructions, giving advice on the necessity
of regular servicing.
7. Demonstrate to the user the action required if a gas
leak occurs or is suspected. Show them how to turn off
the gas supply at the meter control, and advise them
not to operate electric light or power switched, and to
ventilate the property.
8. Show the user the location of the system control
isolation switch, and demonstrate its operation.
9. Advise the user that they may observe a plume of
vapour from the flue terminal, and that it is part of the
normal operation of the boiler.
Lower Door Panel
© Baxi Heating UK Ltd 2014
Fig. 38
10. Complete the label supplied with the inhibitor and
stick to the inside of the boiler case. Detail of system
treatment must be recorded in the Benchmark
Commissioning Checklist.
41
14.0 Servicing the Boiler
14.1
Annual Servicing
1. For reasons of safety and economy, it is recommended that
the boiler is serviced annually. Servicing must be performed by a
competent person in accordance with B.S. 7967-4.
2. After servicing, complete the relevant Service Interval Record
section of the Benchmark Commissioning Checklist at the rear of
this publication.
IMPORTANT: During routine servicing, and after any
maintenance or change of part of the combustion circuit, the
following must be checked:• The integrity of the complete flue system and the flue seals.
• The integrity of the boiler combustion circuit and relevant
seals as described in Section 14.2.
• The operational gas inlet pressure as described in Section
12.2.1 to 12.2.3 and the gas rate as described in 12.2.4.
• The combustion performance as described in ‘Check the
Combustion Performance’ (14.1.4 to 14.1.6 below).
3. Competence to carry out Checking Combustion
Performance
B.S. 6798 ‘Specification for Installation & Maintenance of Gas
Fired Boilers not exceeding 70kW’ advises that:• The person carrying out a combustion measurement should
have been assessed as competent in the use of a flue gas
analyser and the interpretation of the results.
• The flue gas analyser used should be one meeting the
requirements of BS7927 or BS-EN50379-3 and be calibrated
in accordance with the analyser manufacturers’ requirements.
• Competence can be demonstrated by satisfactory
completion of the CPA1 ACS assessment, which covers the
use of electronic portable combustion gas analysers in
accordance with BS 7967, Parts 1 to 4.
Check the Combustion Performance (CO/CO2 ratio)
4. Set the boiler to operate at maximum rate as described in
Section 12.2.
5. Remove the cap from the flue sampling point, insert the
analyser probe and obtain the CO/CO2 ratio. This must be
less than 0.004.
6. If the combustion reading (CO/CO2 ratio) is greater than
this, and the integrity of the complete flue system and
combustion circuit seals has been verified, and the inlet gas
pressure and gas rate are satisfactory either:
• Perform the ‘Annual Servicing - Inspection’ (Section 14.2) &
re-check.
• Replace the gas valve (Section 15.8) & re-check.
42
© Baxi Heating UK Ltd 2014
14.0
14.2
Servicing the Boiler
Annual Servicing - Inspection
1. Ensure that the boiler is cool.
2. The boiler cannot be switched off at the boiler, therefore it
is important to isolate the electrical supply at the mains fuse.
3. Hazardous materials are not used in the construction of
these products, however reasonable care during service is
recommended.
4. When replacing the combustion box door after servicing it is
essential that the retaining screws are tightened fully.
5. Ensure that both the gas and electrical supplies to the
boiler are isolated.
6. Remove the outercase and lower door panel (see Fitting the
Outercase, Section 13.0).
WARNING: The PCB Control and Fan
Assembly are 325 Vdc. Isolate at supply
before access.
7. Release the four 1/4 turn screws securing the air box door
panel and remove the door (Fig. 39).
Fig. 39
Lead Terminals
Air Box Door Panel
8. Disconnect the leads from the centre and right hand
terminals (earth and flame sensing probe) (Fig. 40). Reconnect
in reverse order.
9. Undo the four screws securing the combustion box door
and remove the door (Fig. 41).
10. Visually check for debris/damage and clean or replace if
necessary the following:
Earth
Spark
a) Burner.
b) Heat exchanger fins.
c) Fan compartment (Check also for condensate leaks).
d) Insulation.
e) Door seals-Important: Pay particular attention to
the condition of the combustion box door seals.
f) Electrodes.
g) The condensate trap
NOTE: Remove the trap drain plug and place a vessel
underneath to catch the condensate (care should be
taken as this could be hot). Clean the trap and refit
the drain plug. Check for leaks.
h) Top of heat exchanger.
Sleeve
Sensing
Fig. 40
Combustion Box
Door Panel
© Baxi Heating UK Ltd 2014
Fig. 41
43
14.0
14.2
Servicing the Boiler
Annual Servicing - Inspection (Cont)
Flue Sampling Point
11. To clean the heat exchanger and burner proceed as
follows:
a) Disconnect the electrical leads to the fan component
protection sensor (Fig. 42).
Fig. 41a
b) Loosen the screw retaining the gas injector pipe at
the venturi (Fig. 42).
c) Undo the two wing nuts to disconnect the fan
(Fig. 42).
d) Remove the fan and disconnect the electrical supply
to it (Fig. 42).
Injector Pipe
e) Remove the gas injector pipe from the gas valve
(push-fit) (Fig. 42).
f) Undo the condensate trap securing nut, lock nut and
the condensate drain pipe. Remove the condensate trap
and disconnect the sensor leads (Fig. 43).
Injector Pipe Retaining
Screw
g) Remove the two screws securing the burner and
remove the burner. Visually inspect the internal burner
baffle for obstruction, check seal around baffle for
cracks/damage. Clean with a soft brush.
Securing Nut
Fan
h) Loosen the two screws retaining the heat exchanger
support bracket and slide to the left to remove
(Fig. 44).
Sensor
Leads
Protection
Sensor Leads
Fig. 42
i) Remove the four screws securing the heat
exchanger/combustion box base and withdraw the
base.
Electrical Supply
Condensate
Trap
Wing Nuts
Lock Nut
Service Drain
Plug
Condensate
Drain Pipe
Central Insulation Panel
Fig. 43
j) Lower the central insulation panel and check
condition (Fig. 44). Replace the lower insulation pad if
necessary.
k) Ensure the heat exchanger fins are clear of any
obstruction.
l) Check condition of all seals. Important: Pay particular
attention to the condition of the combustion box
door seals.
Burner
Combustion
Box Base
Heat Exchanger
Support Bracket
m) Reassemble in reverse order and check for leaks.
12. Check the CO/CO2 ratio and CO2 level at the flue
sampling point (Fig.41a) is as quoted in Section 4.0,
‘Technical Data’.
13. If the ratio or level is greater than that quoted
telephone the Technical Enquiries for further advice.
IMPORTANT: No adjustment of the gas
valve is permissible.
Burner Securing
Screws
44
Combustion Box Base
Securing Screws
Fig. 44
© Baxi Heating UK Ltd 2014
14. Complete the relevant Service Interval Record
section of the Benchmark Commissioning Checklist at
the rear of this publication and then hand it back to the
user.
15.0
15.1
Changing Components
Changing Components
IMPORTANT: When changing components ensure
that both the gas and electrical supplies to the boiler
are isolated before any work is started.
“The boiler cannot be switched off at the boiler,
therefore it is important to isolate the electrical
supply at the mains fuse.”
Hazardous materials are not used in the construction
of these products, however reasonable care during
service is recommended.
When replacing the combustion box door after
changing components, it is essential that the retaining
screws are tightened fully.
After Changing Components a combustion check
should be performed (see Section 15.8.11). This is
especially important on gas carrying parts, and those
that may affect combustion (e.g. fan).
1. Before changing any components please read Section
1.2 Important Information.
Fig. 45
2. Remove the outer case and lower door panel (see
“Fitting the Outercase” Section 13.0).
Heat Exchanger
Manifold
WARNING: The PCB Control and Fan
Assembly are 325 Vdc. Isolate at supply
before access.
Drain Point
Tube
Electrical Connections
3. Isolate the water circuit and drain the system as
necessary. A drain point is located on the heat
exchanger manifold at the right hand side of the boiler
(Fig. 45) to enable the heat exchanger to be drained.
4. Place a tube on the drain point to drain water away
from electrics. Turn anticlockwise to open (Fig. 45).
Flow Temperature Thermistor
NOTE: When reassembling always fit new ‘O’ rings,
ensuring their correct location on the spigot. Green
“O” rings are used for gas joints and Black “O” rings
for water joints. Use Greasil 4000 (Approved
Silicone Grease).
5. After changing a component re-commission the
boiler where appropriate and check the inhibitor
concentration (see Section 6.2 and 12.1).
Safety
Thermostat
The thermistor, safety thermostat, interface PCB and
the flow switch can be accessed after removal of the
outer case.
Fig. 46
15.2
Flow Temperature Thermistor and
Safety Thermostat (Fig. 46)
1. The procedure is the same for both the thermistor
and the safety thermostat.
2. Remove the electrical connections from the sensor.
3. Unscrew the sensor from the pipe.
© Baxi Heating UK Ltd 2014
4. Fit the new thermistor or safety thermostat and
reassemble in reverse order.
45
15.0
Changing Components
Support Bracket
15.3
Flowswitch (Fig. 47)
1. Drain the boiler (see Section 15.1 paragraph 2 & 3).
2. Remove the two screws on the support bracket.
3. Remove the clip securing the flow pipe to the
flowswitch.
4. Disconnect the inline electrical connection.
5. Pull pipe away from flowswitch.
Flow Switch
6. Remove the two screws securing the flowswitch to
the boiler.
7. Remove the flowswitch.
Flow Pipe
Clip
8. Fit the new flowswitch and reassemble in reverse
order.
Fig. 47
9. Recommission the boiler and check the inhibitor
concentration (see Section 6.2 and 12.1).
15.4
PCB (Figs. 48 & 49)
WARNING: The PCB Control and Fan
Assembly are 325 Vdc. Isolate at supply
before access.
1. Remove the plastic button cover. Refit them onto the
new PCB (Fig. 48).
Plastic
Button
Cover
1. Remove the top right hand securing screw and hinge
down the PCB housing and disconnect the electrical
connections noting their positions
2. Lift the Control PCB housing out of hinge housing of
metal bracket.
3. Fit the new PCB Housing Assembly and reassemble
in reverse order.
Fig. 48
PCB Housing Securing
Screw
Hinge down
PCB Housing
Fig. 49
46
© Baxi Heating UK Ltd 2014
15.0
Changing Components
The fan and venturi, gas valve, injector pipe,
condensate trap, fan protection sensor, spark and
sensing electrodes can be accessed and changed on
the removal of the airbox door panel.
1. Remove the airbox door panel by loosening the four
1
/4 turn screws (Fig. 50).
15.5
Spark and Sensing Electrodes
(Fig. 51)
1. Disconnect all three leads from tabs.
Spark
Opaque cable
Earth
Green/Yellow cable
Sensing
White cable
2. Remove the two screws securing each of the
electrodes to the combustion box door and remove the
electrodes.
Fig. 50
3. Fit the new electrodes (and new gasket, as required)
and reassemble in reverse order.
Air Box Door Panel
15.6
Fan (Fig. 52)
WARNING: The PCB Control and Fan
Assembly are 325 Vdc. Isolate at supply
before access.
Earth
1. Loosen the screw holding the injector pipe into the
venturi.
2. Remove the electrical connections to the fan and
protection sensor on the fan.
Sensing
Combustion
Box Door
Spark
3. Remove the wing nuts securing the fan to the base of
the combustion box.
Fig. 51
4. Lower the fan and remove.
5. If changing the fan remove the screws securing the
venturi and fan protection sensor bracket, noting the
positions of the injector opening and sensor bracket, fix
them to the new fan.
Injector Pipe
Injector
Opening
Screw
6. Fit the new fan and reassemble in reverse order.
Gasket
Fan
The injector pipe, condensate trap and gas valve can
be changed after the removal of
the fan.
Protection
Sensor
Venturi
Electrical Connections
Fig. 52
Electrical Connection
© Baxi Heating UK Ltd 2014
Wing Nuts
47
15.0
Changing Components
The removal of the fan is necessary to enable the
changing of the injector pipe, condensate trap and gas
valve (see section 15.6).
15.7
Injector Pipe (Fig. 53)
1. Remove the injector pipe by pulling out from the ‘O’
ring joint in the gas valve.
2. Fit the new injector pipe and reassemble in reverse
order.
Injector Pipe
15.8
Gas Valve (Fig. 53)
1. Remove the Control PCB (see Section 15.4).
Gas Valve
Securing Screws
2. Isolate gas supply and disconnect the gas tap by
removing the four screws.
3. Undo the case pressure pipe from the gas valve.
Case Pressure Pipe
4. Disconnect the electrical plug from the gas valve.
Gasket
5. Remove the fan (see section 15.6) and injector pipe.
6. Remove the two gas valve securing screws from
inside the air box holding the gas valve.
Boiler Side
Aluminium
Spacer
7. Remove the gas valve from the airbox side.
‘O ring’
Gas Valve
8. Remove the aluminium spacer and its gasket from
the gas valve.
9. Fit the aluminium spacer and gasket to the new valve.
Gas Tap
Fig. 53
Electrical Plug
10. Fit the new gas valve and reassemble in reverse
order.
NOTE: Check for gas tightness after replacing gas
valve.
11. Check the CO/CO2 ratio and CO2 level at the flue
sampling point (Fig.41a) is as quoted in Section 4.0,
‘Technical Data’.
Sensor
Leads
12. If the ratio or level is greater than that quoted,
telephone the Technical Enquiries for further advice.
Securing
Nut
IMPORTANT: No adjustment of the gas
valve is permissible.
15.9
Condensate Trap (Fig. 54)
1. Disconnect the condensate trap from the base of the
heat exchanger.
Condensate
Trap
2. Disconnect the condensate drain (outside the boiler)
from the condensate trap.
3. Undo the condensate trap lock nut and remove the
trap from the boiler. Disconnect the sensor leads.
Lock Nut
Condensate
Drain Pipe
48
© Baxi Heating UK Ltd 2014
Service Drain
Plug
Fig. 54
4. Fit the new condensate trap and reassemble in
reverse order.
5. Prime the condensate trap (fill first chamber), check
for leaks.
15.0
Combustion Box
Door Panel
Changing Components
The burner and heat exchanger can be changed after
removal of the combustion box door. To change the
heat exchanger, the fan and burner must be removed
first (see section 15.6 and 15.10).
1. Remove the combustion box door by removing the
four securing screws (Fig. 55).
IMPORTANT: On refitting the combustion box
door check the condition of the combustion box
door seals.
15.10
Support
Bracket
Fig. 55
Return
Connection
Burner
Fig. 57
Flow
Switch
Burner (Fig. 56)
1. Remove the two screws securing the burner to the
base of the combustion box.
2. Remove the burner carefully from the combustion
box base.
3. Check the burner seal on the heat exchanger base,
replace if necessary. Fit the new burner and reassemble
in reverse order.
15.11
Heat Exchanger
Fig. 56
1. Drain the boiler (see section 15.1 paragraph 2 & 3).
Securing Screws
2. Remove all components in the base of the airbox.
3. Undo the screws on the support bracket. Remove
the screws securing the flow switch and return
connections and remove the connections (Fig. 57).
4. Remove the screws securing the heat exchanger
manifold and remove the manifold (Fig. 58).
5. Lift the heat exchanger assembly (Fig. 59) and rotate
the bottom upwards whilst pulling it forwards out of the
airbox.
6. Fit the new heat exchanger and reassemble in reverse
order.
Fig. 58
7. Recommission the boiler and check the inhibitor
concentration (see Section 6.2 and 12.1).
Heat Exchanger
Manifold
Heat Exchanger
Assembly
Fig. 59
© Baxi Heating UK Ltd 2014
49
15.0
15.12
Changing Components
Heat Exchanger Lower Insulation Pad
(Fig. 60)
1. Remove all components in the base of the airbox.
2. Remove the burner (see section 15.10).
3. Remove the four bolts securing the combustion box
base.
4. Remove the combustion box base.
5. Pull the central insulation panel down from the
centre of the heat exchanger and remove the lower
insulation pad.
Central Insulation Panel
Upper Insulation
Pad
6. Fit the new insulation pad and reassemble in reverse
order.
Lower Insulation
Pad
Fig. 60
15.13
Heat Exchanger Upper Insulation Pad
(Fig. 60)
Burner
1. Remove all components in the base of the airbox.
2. Remove the burner (see section 15.10).
Combustion
Box Base
Support Bracket
3. Remove the heat exchanger (see section 15.11).
4. Remove the four bolts securing the combustion box
base.
5. Remove the combustion box base.
Burner Securing
Screws
Combustion Box Base
Securing Screws
6. Pull the central insulation panel down from the
centre of the heat exchanger.
7. Fit the new insulation pad and reassemble in reverse
order.
50
© Baxi Heating UK Ltd 2014
16.0
Short Parts List
Short Parts List
A
B
C
Key
No.
G.C.
No.
Description
A
E06 058
Flow Temperature
B
E06 059
C
E06 060
Manufacturers
Part No.
Thermistor (Red)
240670
Flow Switch
242459
Safety Thermostat
(Black)
242235
D
PCB
5129147
E
Fan
5109925
F
Gas Valve
241900
Viewing Window
242484
H
Condensate Trap
5111714
I
Electrodes Kit
5132097
J
Burner Assy
5107430
Heat Exchanger Assy
242497
E
G
D
G
K
E06 085
E06 097
F
I
H
K
J
© Baxi Heating UK Ltd 2014
51
17.0
High
Fault Finding
Reset
NOTE: The fan is supplied with 325 Vdc.
Low
Fan Fault Finding should only be carried out after the
boiler has been electrically isolated.
ON
Lockout
Boiler On
Mains On
LED Light
(Red)
LED Light
(Green)
LED Light
(Green)
Lights
Off Off Off
YES
General Fault Finding should only be carried out by
someone who is appropriately qualified.
Go to Electrical Supply
section of the fault finding
instructions.
ON
Lights
On Off Flash
YES
YES
Go to Dry-Fire
section of the fault finding
instructions.
ON
Lights
On On On
Lights
Flash On Flash
YES
Go to Overheat Lockout
section of the fault finding
instructions.
© Baxi Heating UK Ltd 2014
YES
YES
Low Electrical Supply
Incoming Voltage less than
180V. Check System
Controls & System Wiring.
Otherwise contact Electricity
Provider.
LV Wiring Harness Ensure 8way PCB connector securely
pushed in. If fault persists
replace LV wiring harness.
Go to Fan Lockout
section of the fault finding
instructions.
YES
PCB Fault
Replace PCB.
YES
PCB Fault
Replace PCB.
YES
PCB Fault
Replace PCB.
ON
Lights
On On Flash
ON
Lights
Flash On On
ON
52
Go to Thermistor section
of the fault finding
instructions.
Go to Ignition Lockout section
of the fault finding instructions.
ON
Lights
Flash Flash On
YES
ON
YES
ON
Lights
Flash Off On
Lights
Flash Off Flash
ON
ON
Lights
On Off On
YES
ON
Live & Neutral Reversed
Incoming Live and Neutral
reversed.
ON
Lights
On Flash Flash
Lights
On Flash On
Lights
Off Off Off
ELECTRICAL SUPPLY
17.0
Fault Finding
ON
NO
240V at A ?
No Switched Live to
boiler. Check Systems
Controls and System
Wiring.
YES
NO
240V at B ?
A
Check wiring from
terminal block to PCB.
YES
L
NO
PCB fuse OK ?
Check for shorts on
pump, fan & gas valve.
Replace if shorted &
replace fuse.
N
Optional
Pump
Live
YES
Replace PCB.
B
Fuse
© Baxi Heating UK Ltd 2014
53
17.0
Lights
On Flash Flash
DRY-FIRE
Fault Finding
ON
Are
Flow & Return reversed ?
YES
Swop Flow & Return.
E
NO
Is the
system full of water ?
NO
Fill system with water and
bleed out all air.
L
N
Optional
Pump
YES
YES
Turn
mains off & on. After 5 sec, is
there 240V
at E?
NO
Is the
pump running ?
YES
YES
Unplug
5-way PCB
connector. Is there continuity
between H (run pump from
switched live) ?
Replace PCB.
Live
NO
Turn
mains off, unplug
7-way connector to PCB.
Is there continuity between
F and G ?
NO
Pump or Pump Wiring
fault.
Wiring from terminal
block to PCB faulty.
YES
Replace PCB.
H
G
Viewed from
Wire Entry end
NO
7-way Connector
F
Disconnect
Flow Switch Inline
connector. With pump running is
there continuity across flow
switch ?
YES
Wires from inline
connector to PCB faulty.
L
NO
Remove
flow switch from boiler.
Is there a physical blockage to
the paddle within the
flow switch ?
YES
Remove Blockage.
54
© Baxi Heating UK Ltd 2014
N
Optional
Pump
Live
NO
Is there a
blockage in the system ?
YES
Remove Blockage.
NO
Replace Flow Switch.
17.0
Lights
On Off On
IGNITION LOCKOUT
Fault Finding
ON
I
Is
there gas at gas valve inlet ?
NO
Check isolation valve and
gas supply.
J
5-way Connector
YES
Remove
5-way connector
from gas valve. Is there 240
Vdc between I & J
during ignition ?
NO
Reset Lockout.
Is there gas flow
(check at meter) ?
YES
Replace Gas Valve.
NO
YES
Is
there at least
18mbar dynamic at gas valve
inlet ?
NO
Remove
the larger or the
two 6-way PCB connectors.
Is there continuity from I to L
& from J to K ?
Remove Gas Valve & check
inlet filter for blockage.
Otherwise incorrect gas supply
to boiler.
NO
Lead from PCB to Gas
Valve faulty.
YES
Replace PCB.
YES
Is
Condensate Trap
blocked or water on
terminals ?
YES
Clear blockage and dry
sensors.
K
L
NO
Is
spark or flame detection
probe damaged ?
6-way Connector
YES
Replace spark or flame
detection probe and
gaskets.
NO
Is
spark gap between 3 and
4mm ?
NO
Set spark gap to 3.5mm.
YES
Is
wiring from PCB
to spark probe & flame
detection probe OK ?
NO
Rectify wiring.
© Baxi Heating UK Ltd 2014
YES
Is the
burner blocked or
damaged ?
NO
Replace PCB.
YES
Clean burner or replace as
necessary.
55
Lights
Flash Off On
OVERHEAT LOCKOUT
17.0
Fault Finding
ON
Disconnect
black stat on flow pipe.
When flow < 60° C is there
continuity across stat ?
NO
Replace Stat.
YES
Reconnect stat.
Disconnect fan stat.
When fan temp < 60° C
is there continuity
across stat ?
NO
Replace Stat.
YES
Reconnect stat.
Disconnect the larger of
the 6-way PCB connectors.
Is there continuity
across M ?
NO
YES
Disconnect
thermistor
(red sensor on flow pipe).
Is resistance between
0.5kΩ & 20kΩ ?
6-way Connector
NO
Replace thermistor.
YES
Is
combustion chamber
door seal damaged or not in
place ?
NO
Replace PCB.
56
© Baxi Heating UK Ltd 2014
M
Wiring from PCB to
thermostats faulty.
YES
Replace combustion
chamber door seal & trim
seal.
17.0
Lights
Flash Flash On
FAN LOCKOUT
Fault Finding
NOTE: The fan is supplied with 325 Vdc.
ON
Fan Fault Finding should only be carried out after the
boiler has been electrically isolated.
Fan
Connection
Unplug
3-way PCB connector
& unplug fan. Is there
continuity from N to O &
from P to Q ?
NO
Rectify wiring.
PCB
Connection
O
N
Q
P
YES
Unplug
the smaller of the
6-way PCB connector. Is there
continuity from R to S & from T
to U & from
V to W ?
Fan
Connection
PCB
Connection
NO
Rectify wiring.
R
T
V
S
U
W
YES
Viewed from
Wire Entry end
Replace fan.
Lights
On Flash On
THERMISTOR
ON
Unplug
thermistor,
Is thermistor resistance between
0.5kΩ & 20kΩ ?
NO
Replace thermistor.
D
YES
Plug in
thermistor, leave
8-way connector unplugged.
Is resistance at D between
0.5kΩ & 20kΩ ?
NO
Wiring from PCB to
thermistor faulty.
Viewed from
Wire Entry end
YES
Replace PCB.
© Baxi Heating UK Ltd 2014
57
GAS BOILER SYSTEM COMMISSIONING CHECKLIST
This Commissioning Checklist is to be completed in full by the competent person who commissioned the boiler as a means of demonstrating
compliance with the appropriate Building Regulations and then handed to the customer to keep for future reference.
Failure to install and commission according to the manufacturer’s instructions and complete this Benchmark Commissioning Checklist will invalidate the
warranty. This does not affect the customer’s statutory rights.
Customer name:
Telephone number:
Address:
Boiler make and model:
Boiler serial number:
Commissioned by (PRINT NAME):
Gas Safe register number:
Company name:
Telephone number:
Company address:
Commissioning date:
CONTROLS (tick the appropriate boxes)
Time and temperature control to heating
Time and temperature control to hot water
Room thermostat and programmer/timer
Programmable room thermostat
Load/weather compensation
Optimum start control
Cylinder thermostat and programmer/timer
Combination Boiler
Heating zone valves
Fitted
Not required
Hot water zone valves
Fitted
Not required
Thermostatic radiator valves
Fitted
Not required
Automatic bypass to system
Fitted
Not required
Boiler interlock
Provided
ALL SYSTEMS
’s instructions
Yes
What system cleaner was used?
What inhibitor was used?
Quantity
Yes
litres
No
CENTRAL HEATING MODE measure and record:
Gas rate
m³/hr
OR
ft³/hr
Burner operating pressure (if applicable)
mbar
OR Gas inlet pressure
mbar
°C
Central heating return temperature
°C
COMBINATION BOILERS ONLY
Is the installation in a hard water area (above 200ppm)?
Yes
No
Yes
No
DOMESTIC HOT WATER MODE Measure and Record:
Gas rate
m³/hr
Burner operating pressure (at maximum rate)
mbar OR Gas inlet pressure at maximum rate
OR
ft³/hr
mbar
Cold water inlet temperature
°C
Hot water has been checked at all outlets
Yes
Temperature
°C
I/min
CONDENSING BOILERS ONLY
The condensate drain has been installed in accordance with the manufacturer’s instructions and/or BS5546/BS6798
Yes
ALL INSTALLATIONS
Record the following:
At max. rate:
CO
ppm AND
At min. rate: (where possible)
CO
ppm AND
CO/CO²
CO/CO²
Ratio
Ratio
The heating and hot water system complies with the appropriate Building Regulations
Yes
The boiler and associated products have been installed and commissioned in accordance with the manufacturer’s instructions
Yes
The operation of the boiler and system controls have been demonstrated to and understood by the customer
Yes
The manufacturer’s literature, including Benchmark Checklist and Service Record, has been explained and left with the customer
Yes
Commissioning Engineer’s Signature
Customer’s Signature
*All installations in England and Wales must be
to Local Authority Building Control (LABC) either directly or through a
will then be issued to the customer.
Competent Persons Scheme. A Building Regulations Compliance
58
© Heating and Hotwater Industry Council (HHIC)
www.centralheating.co.uk
SERVICE RECORD
It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed.
Service Provider
Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the manufacturer’s instructions.
SERVICE 01
Date:
SERVICE 02
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Record:
At max. rate:
Gas safe register No:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
Comments:
Comments:
Signature
Signature
SERVICE 03
Date:
SERVICE 04
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Record:
At max. rate:
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
CO
ppm
AND
ppm
AND
Comments:
Signature
Signature
SERVICE 05
Date:
SERVICE 06
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
CO
ppm
AND
ppm
AND
Comments:
Signature
Signature
SERVICE 07
Date:
SERVICE 08
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
Date:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
Comments:
Comments:
Signature
Signature
SERVICE 09
Date:
SERVICE 10
Engineer name:
Engineer name:
Company name:
Company name:
Telephone No:
Telephone No:
Gas safe register No:
Record:
CO² %
CO² %
Gas safe register No:
CO
At max. rate:
Date:
At min. rate: (Where Possible) CO
Comments:
Record:
CO² %
CO² %
Gas safe register No:
CO
At max. rate:
Date:
At min. rate: (Where Possible) CO
Comments:
Record:
CO² %
CO² %
Gas safe register No:
CO
At max. rate:
Date:
CO² %
CO² %
Date:
Gas safe register No:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
CO² %
CO² %
Record:
At max. rate:
CO
ppm
AND
At min. rate: (Where Possible) CO
ppm
AND
Comments:
Comments:
Signature
Signature
CO² %
CO² %
to Local Authority Building Control (LABC) either directly or through a
*All installations in England and Wales must be
Competent Persons Scheme. A Building Regulations Compliance
will then be issued to the customer.
© Heating and Hotwater Industry Council (HHIC)
www.centralheating.co.uk
59
All descriptions and illustrations provided in this leaflet have been carefully
prepared but we reserve the right to make changes and improvements in
our products which may affect the accuracy of the information contained in
this leaflet. All goods are sold subject to our standard Conditions of Sale
which are available on request.
P O T T E RTON
A Tr a din g D i v i s i o n o f B ax i H eat i ng U K Lt d ( 3879156)
Brooks House, Coventry Road, Warwick. CV34 4LL
After Sales Service 0844 871 1560 Technical Enquiries 0844 871 1555
Website www.potterton.co.uk
e&oe
© Baxi Heating UK Ltd 2014
7205141 - 06 (2/14)