Compaq 6520s - Notebook PC Specifications

HP Compaq 6520s Notebook PC
Maintenance and Service Guide
© Copyright 2007 Hewlett-Packard
Development Company, L.P.
AMD, the AMD Arrow logo, and
combinations thereof, are trademarks of
Advanced Micro Devices, Inc. Bluetooth is
a trademark owned by its proprietor and
used by Hewlett-Packard Company under
license. Intel, Core, Pentium, Celeron are
trademarks of Intel Corporation in the
United States and other countries.
Microsoft, Windows, and Windows Vista are
either trademarks or registered trademarks
of Microsoft Corporation in the United
States and/or other countries. SD Logo is a
trademark of its proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
Third Edition: November 2007
First Edition: July 2007
Document Part Number: 456941-003
MSG revision history
Revision
Publication date
Description
A
October 2010
The top cover, spare part number 456599-001, does not include the TouchPad
board and cable, and TouchPad button board and cable. The TouchPad board is
available using spare part number 456600-001. The TouchPad button board and
cable are available using spare part number 456601-001. The TouchPad board
cable, TouchPad bracket, and TouchPad button board actuators are available in
the TouchPad Miscellaneous Kit, spare part number 456602-001. The top cover
description has been corrected.
iii
iv
MSG revision history
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on
a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to
contact the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer
and the AC adapter comply with the user-accessible surface temperature limits defined by the
International Standard for Safety of Information Technology Equipment (IEC 60950).
v
vi
Safety warning notice
Table of contents
1 Product description ........................................................................................................................................ 1
2 External component identification ................................................................................................................ 7
Top components ................................................................................................................................... 7
TouchPad ............................................................................................................................ 7
Buttons, lights, and speaker ................................................................................................ 8
Keys ..................................................................................................................................... 9
Front components .............................................................................................................................. 10
Right-side components ....................................................................................................................... 10
Left-side components ......................................................................................................................... 11
Bottom components ........................................................................................................................... 12
3 Illustrated parts catalog ............................................................................................................................... 13
Serial number location ........................................................................................................................ 13
Computer major components ............................................................................................................. 14
Plastics Kit .......................................................................................................................................... 20
Cable Kit ............................................................................................................................................. 21
Mass storage devices ......................................................................................................................... 22
Miscellaneous parts ............................................................................................................................ 23
Sequential part number listing ............................................................................................................ 24
4 Removal and replacement procedures ....................................................................................................... 29
Preliminary replacement requirements ............................................................................................... 29
Tools required .................................................................................................................... 29
Service considerations ....................................................................................................... 29
Plastic parts ....................................................................................................... 29
Cables and connectors ..................................................................................... 30
Drive handling ................................................................................................... 30
Grounding guidelines ......................................................................................................... 31
Electrostatic discharge damage ........................................................................ 31
Packaging and transporting guidelines ............................................. 32
Workstation guidelines ..................................................................... 32
Equipment guidelines ....................................................................... 33
vii
Unknown user password ................................................................................................... 34
Component replacement procedures ................................................................................................. 35
Serial number .................................................................................................................... 35
Computer feet .................................................................................................................... 36
Battery ............................................................................................................................... 37
Hard drive .......................................................................................................................... 38
WLAN module .................................................................................................................... 40
Memory module ................................................................................................................. 43
Optical drive ....................................................................................................................... 45
Switch cover and keyboard ................................................................................................ 47
Speaker ............................................................................................................................. 51
Display lid switch module ................................................................................................... 52
Display assembly ............................................................................................................... 53
Top cover ........................................................................................................................... 58
TouchPad board and TouchPad button board ................................................................... 61
Bluetooth module ............................................................................................................... 64
System board ..................................................................................................................... 66
Fan ..................................................................................................................................... 69
Heat sink ............................................................................................................................ 71
Processor ........................................................................................................................... 74
Modem module .................................................................................................................. 76
RTC battery ....................................................................................................................... 78
5 Computer Setup ............................................................................................................................................ 80
Starting Computer Setup .................................................................................................................... 80
Using Computer Setup ....................................................................................................................... 81
Navigating and selecting in Computer Setup ..................................................................... 81
Restoring factory settings in Computer Setup ................................................................... 81
Computer Setup menus ..................................................................................................................... 82
File menu ........................................................................................................................... 82
Security menu .................................................................................................................... 83
Diagnostics menu .............................................................................................................. 83
System Configuration menu .............................................................................................. 84
6 Specifications ................................................................................................................................................ 86
Computer specifications ..................................................................................................................... 86
14.1-inch, WXGA display specifications ............................................................................................. 87
Hard drive specifications .................................................................................................................... 88
DVD±RW and CD-RW Double-Layer Combo Drive specifications .................................................... 89
DVD/CD-RW Combo Drive specifications .......................................................................................... 90
System DMA specifications ................................................................................................................ 91
System interrupt specifications ........................................................................................................... 92
System I/O address specifications ..................................................................................................... 93
viii
System memory map specifications ................................................................................................... 95
7 Screw listing .................................................................................................................................................. 96
Phillips PM2.0×5.0 captive screw ....................................................................................................... 97
Phillips PM2.5×12.0 captive screw ..................................................................................................... 98
Phillips PM3.0×4.0 screw ................................................................................................................... 99
Phillips PM2.5×4.0 screw ................................................................................................................. 100
Torx T8M2.5×7.0 screw ................................................................................................................... 101
Phillips PM2.0×4.0 screw ................................................................................................................. 104
Torx T8M2.5×3.0 broad-head screw ................................................................................................ 106
Torx T8M2.5×4.0 screw ................................................................................................................... 107
Torx T8M2.5×6.0 screw ................................................................................................................... 108
Phillips PM2.0×2.0 broad-head screw .............................................................................................. 109
Phillips PM2.0×6.0 screw ................................................................................................................. 110
Phillips PM2.5×7.0 screw ................................................................................................................. 111
Phillips PM2.5×7.0 captive screw ..................................................................................................... 112
Phillips PM2.5×10.0 captive screw ................................................................................................... 113
Phillips PM2.0×8.0 screw ................................................................................................................. 115
8 Backup and recovery .................................................................................................................................. 116
Creating recovery discs in Windows VIsta ....................................................................................... 116
Backing up your information in Windows Vista ................................................................................ 117
When to back up .............................................................................................................. 117
Backup suggestions ......................................................................................................... 117
Backing up specific files or folders ................................................................................... 118
Backing up the entire hard drive ...................................................................................... 118
Creating recovery points .................................................................................................. 119
Scheduling backups ......................................................................................................... 119
Performing a recovery in Windows Vista .......................................................................................... 120
Performing a recovery from the recovery discs ............................................................... 120
Performing a recovery from the hard drive ...................................................................... 120
Initiating a recovery in Windows ...................................................................... 121
Initiating a recovery from the hard drive recovery partition ............................. 121
Creating recovery discs in Windows XP ........................................................................................... 122
Backing up your information in Windows XP .................................................................................... 123
When to back up .............................................................................................................. 123
Backup suggestions ......................................................................................................... 123
Backing up specific files or folders ................................................................................... 124
Backing up the entire hard drive ...................................................................................... 124
Creating recovery points .................................................................................................. 125
Scheduling backups ......................................................................................................... 125
Performing a recovery in Windows XP ............................................................................................. 126
Performing a recovery from the recovery discs ............................................................... 126
ix
Performing a recovery from the hard drive ...................................................................... 126
Initiating a recovery in Windows ...................................................................... 127
Initiating a recovery from the hard drive recovery partition ............................. 128
9 Connector pin assignments ....................................................................................................................... 129
Audio-out (headphone) ..................................................................................................................... 129
Audio-in (microphone) ...................................................................................................................... 129
External monitor ............................................................................................................................... 130
RJ-11 (modem) ................................................................................................................................ 131
RJ-45 (network) ................................................................................................................................ 132
Universal Serial Bus ......................................................................................................................... 132
10 Power cord set requirements .................................................................................................................. 133
Requirements for all countries and regions ...................................................................................... 133
Requirements for specific countries and regions ............................................................................. 134
11 Recycling ................................................................................................................................................... 135
Battery .............................................................................................................................................. 135
Display .............................................................................................................................................. 135
Index ................................................................................................................................................................. 141
x
1
Product description
Category
Description
Computer
models equipped
with GLE960
system board
Computer
models
equipped with
GME965 system
board
Computer
models
equipped with
PM965 system
board
Product
Name
HP Compaq 6520s Notebook PC
√
√
√
Processors
Intel® Core™ 2 Duo processors
●
T9300 2.50-GHz processor, 6-MB L2
cache, 800-MHz front side bus (FSB)
√
√
●
T8300 2.40-GHz processor, 3-MB L2
cache, 800-MHz FSB
√
√
●
T8100 2.10-GHz processor, 3-MB L2
cache, 800-MHz FSB
√
√
●
T7800 2.60-GHz processor, 4-MB L2
cache, 800-MHz FSB
√
√
●
T7700 2.40-GHz processor, 4-MB L2
cache, 800-MHz FSB
√
√
●
T7500 2.20-GHz processor, 4-MB L2
cache, 800-MHz FSB
√
√
●
T7300 2.00-GHz processor, 4-MB L2
cache, 800-MHz FSB
√
√
●
T7250 2.00-GHz processor, 2-MB L2
cache, 800-MHz FSB
√
√
●
T7100 1.80-GHz processor, 2-MB L2
cache, 800-MHz FSB
√
√
●
T5550 1.83-GHz processor, 2-MB L2
cache, 800-MHz FSB
√
√
●
T5470 1.60-GHz processor, 2-MB L2
cache, 800-MHz FSB
√
√
●
T5270 1.40-GHz processor, 2-MB L2
cache, 800-MHz FSB
√
√
Intel Celeron® M processors
●
550 2.00-GHz processor, 1-MB L2
cache, 533-MHz FSB
√
1
Category
Chipset
Description
Computer
models equipped
with GLE960
system board
●
540 1.86-GHz processor, 1-MB L2
cache, 533-MHz FSB
√
●
530 1.73-GHz processor, 1-MB L2
cache, 533-MHz FSB
√
Northbridge: Intel PM965 with up to 800MHz FSB
Panels
Memory
2
Computer
models
equipped with
PM965 system
board
√
Northbridge: Intel GME965 with up to 800MHz FSB
Graphics
Computer
models
equipped with
GME965 system
board
√
Northbridge: Intel GLE960 with up to 533MHz FSB
√
Southbridge: Intel ICH8M
√
√
ATI-M62s discrete graphics subsystem
memory
√
√
Intel Universal Memory Architecture
(UMA) graphics subsystem integrated with
shared video memory (dynamically
allocated)
√
√
All display assemblies include 2 wireless
local area network (WLAN) antennae
√
√
√
●
14.1-inch WXGA BrightView
√
√
√
●
14.1-inch WXGA
√
√
√
2 customer-accessible/upgradable
memory module slots
√
√
√
Supports dual-channel memory
√
√
√
Supports up to 4 GB of system RAM
√
√
√
PC2-5300, 667-MHz, DDR2
√
√
√
Chapter 1 Product description
Category
Description
Computer
models equipped
with GLE960
system board
Computer
models
equipped with
GME965 system
board
Computer
models
equipped with
PM965 system
board
Supports the following configurations in all
countries and regions except Brazil:
√
√
√
√
√
√
Supports 9.5-mm, 2.5-inch hard drives
√
√
√
Customer-accessible
√
√
√
Serial ATA
√
√
√
●
4096-MB total system memory (2048
× 2, dual-channel)
●
3072-MB total system memory (2048
+ 1024)
●
2560-MB total system memory (2048
+ 512)
●
2048-MB total system memory (1024
× 2, dual-channel)
●
2048-MB total system memory (2048
× 1)
●
1536-MB total system memory (1024
+ 512)
●
1024-MB total system memory (512
× 2, dual-channel)
●
1024-MB total system memory (1024
× 1)
●
512-MB total system memory (512 ×
1)
Supports the following configurations only
in Brazil:
Hard
drives
●
2048-MB total system memory (2048
× 1)
●
2048-MB total system memory (1024
× 2, dual-channel)
●
1024-MB total system memory (1024
× 1)
●
1024-MB total system memory (512
× 2, dual-channel)
●
512-MB total system memory (512 ×
1)
3
Category
Description
Computer
models equipped
with GLE960
system board
Computer
models
equipped with
GME965 system
board
Computer
models
equipped with
PM965 system
board
Supports the following drives:
√
√
√
HP 3D DriveGuard
√
√
√
Fixed (removal of 1 screw required)
√
√
√
Customer-accessible
√
√
√
Parallel ATA
√
√
√
12.7-mm tray load
√
√
√
Supports the following drives:
√
√
√
Supports external USB diskette drive only
√
√
√
Supports boot from external USB diskette
drive
√
√
√
Supports 3-mode diskette drive
√
√
√
Audio
HD audio - ADI1981
√
√
√
Modem
56K V.92 1.5-inch data/fax modem with
digital line guard
√
√
√
Modem cable included in Brazil, the
Czech Republic, Europe, France, Greece,
Hungary, Israel, Latin America, Poland,
Russia, Saudi Arabia, Slovakia, Slovenia,
South Africa, Turkey, and the United
Kingdom
√
√
√
Intel 82562GT
√
√
√
S3/S4/S5 wake on LAN: DC - no
√
√
√
S3/S4/S5 wake on LAN: AC - yes
√
√
√
Optical
drives
Diskette
drive
Ethernet
Wireless
4
●
160-GB, 5400-rpm
●
120-GB, 5400-rpm
●
80-GB, 5400-rpm
●
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive with
LightScribe
●
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive
●
DVD/CD-RW Combo Drive
Integrated WLAN options by way of wireless module:
2 WLAN antennae built into display
assembly
√
√
√
Support for no-WLAN option
√
√
√
Chapter 1 Product description
Category
Description
Computer
models equipped
with GLE960
system board
Computer
models
equipped with
GME965 system
board
Computer
models
equipped with
PM965 system
board
Support for the following WLAN formats:
√
√
√
●
Intel 802.11a/b/g/n
●
Broadcom 802.11a/b/g
●
Broadcom 802.11b/g
●
Intel 802.11a/b/g
●
Intel 802.11b/g
Integrated personal area network (PAN) options by way of Bluetooth® module:
External media
card
Ports
Keyboard/
pointing
devices
Power
requirements
Support for no-WPAN option
√
√
√
Broadcom Bluetooth 2.0+EDR
√
√
√
One ExpressCard/54 slot
√
√
√
SD/MMC Card Reader supporting Secure
Digital (SD) Memory Card and
MultiMediaCard (MMC)
√
√
√
Audio-in (mono microphone)
√
√
√
Audio-out (stereo headphone)
√
√
√
RJ-11 (modem)
√
√
√
RJ-45 (Ethernet, includes link and activity
lights)
√
√
√
USB (3)
√
√
√
VGA (Dsub 15-pin) supporting 1600 ×
1200 external resolution at 75-GHz (hot
plug/unplug with auto-detect)
√
√
√
2-pin AC power
√
√
√
11.97-inch keyboard with embedded
numeric keypad
√
√
√
TouchPad only, with 2 TouchPad buttons
and vertical scrolling (taps enabled as
default)
√
√
√
90-W AC adapter with localized cable plug
support (2-wire plug with ground pin,
supports 2-pin DC connector)
√
65-W AC adapter with localized cable plug
support (2-wire plug with ground pin,
supports 2-pin DC connector)
√
√
6-cell, 55-Wh Li-ion battery
√
√
√
6-cell, 47-Wh Li-ion battery
√
√
√
5
Category
Description
Computer
models equipped
with GLE960
system board
Computer
models
equipped with
GME965 system
board
Computer
models
equipped with
PM965 system
board
Security
Supports Kensington security sock
√
√
√
Operating
system
Preinstalled:
Windows Vista® Basic 32 with Office
Ready
√
√
√
Windows Vista Basic 32 Japan with Office
Personal (in Japan only)
√
√
√
Windows Vista Business 32 with Office
Ready
√
√
√
Windows Vista Business 32 Japan with
Office Personal (in Japan only)
√
√
√
Windows Vista Home Premium with Office
Ready
√
√
√
Windows® XP Professional
√
√
√
FreeDOS
√
√
√
Red Flag Linux (in the People's Republic
of China only)
√
√
√
Windows Vista Basic 32
√
√
√
Windows Vista Home Premium
√
√
√
Windows Vista Business 32
√
√
√
Windows XP Professional
√
√
√
Red Flag Linux (in the People's Republic
of China only)
√
√
√
DRDVD Vista
√
√
√
Certified: Microsoft® WHQL
√
√
√
AC adapter
√
√
√
Battery (system)
√
√
√
Hard drive
√
√
√
Memory module
√
√
√
Optical drive
√
√
√
WLAN module
√
√
√
Restore media:
Serviceability
6
End-user replaceable parts:
Chapter 1 Product description
2
External component identification
Top components
TouchPad
Item
Component
Function
(1)
TouchPad*
Moves the pointer and selects or activates items on the
screen.
(2)
Left TouchPad button*
Functions like the left button on an external mouse.
(3)
Right TouchPad button*
Functions like the right button on an external mouse.
(4)
TouchPad scroll zone
Scrolls up or down.
*This table describes factory settings. View or change pointing device preferences as follows:
●
In Windows Vista, select Start > Control Panel > Hardware and Sound > Mouse.
●
In Windows XP, select Start > Control Panel > Printers and Other Hardware > Mouse.
Top components
7
Buttons, lights, and speaker
Item
Component
Function
(1)
Caps lock light
On: Caps lock is on.
(2)
Wireless button
Turns the wireless feature on or off, but does not
establish a wireless connection.
NOTE: A wireless network must be set up in order to
establish a wireless connection.
(3)
(4)
Wireless light
Power button
●
On: An integrated wireless device, such as a
wireless local area network (WLAN) device, the HP
Broadband Wireless Module, and/or a Bluetooth®
device, is on.
●
Off: All wireless devices are off.
●
When the computer is off, press the button to turn
on the computer.
●
When the computer is on, press the button to initiate
Hibernation.
●
When the computer is in the Sleep state (Windows
Vista) or in Standby (Windows XP), press the button
briefly to exit the Sleep state or Standby.
●
When the computer is in Hibernation, press the
button briefly to exit Hibernation.
If the computer has stopped responding and Windows®
shutdown procedures are ineffective, press and hold the
power button for at least 5 seconds to turn off the
computer.
To learn more about power settings, follow these steps:
8
Chapter 2 External component identification
●
In Windows Vista, select Start > Control Panel >
System and Maintenance > Power Options.
●
In Windows XP, select Start > Control Panel >
Performance and Maintenance > Power Options.
Item
Component
Function
(5)
Power light
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state
(Windows Vista) or Standby (Windows XP).
●
Off: The computer is off or in Hibernation.
(6)
Speaker
Produces sound.
Item
Component
Function
(1)
esc key
Displays system information when pressed in
combination with the fn key.
(2)
fn key
Executes frequently used system functions when pressed
in combination with a function key or the esc key.
(3)
Windows logo key
Displays the Windows Start menu.
(4)
Windows applications key
Displays a shortcut menu for items beneath the pointer.
(5)
Embedded numeric keypad keys
Can be used like the keys on an external numeric
keypad.
(6)
Function keys
Execute frequently used system functions when pressed
in combination with the fn key.
Keys
Top components
9
Front components
Item
Component
Function
(1)
Audio-out (headphone) jack
Produces sound when connected to optional powered
stereo speakers, headphones, ear buds, a headset, or
television audio.
(2)
Audio-in (microphone) jack
Connects an optional computer headset microphone,
stereo array microphone, or monaural microphone.
(3)
SD/MMC Card Reader
Supports the following optional digital card formats:
SD Memory Card and MMC.
Right-side components
Item
Component
Function
(1)
Optical drive
Reads optical discs and, on select models, also writes to
optical discs.
(2)
Optical drive light
Blinking: The optical drive is being accessed.
(3)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from being
mishandled or stolen.
10
Chapter 2 External component identification
Left-side components
Item
Component
Function
(1)
Battery light
●
Amber: A battery is charging.
●
Blue: A battery is close to full charge capacity.
●
Blinking amber: A battery that is the only available
power source has reached a low battery level. When
the battery reaches a critical battery level, the
battery light begins blinking rapidly.
●
If the computer is plugged into an external power
source, the light turns off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light
stays off until the battery reaches a low battery level.
(2)
ExpressCard slot
Supports optional ExpressCards.
(3)
RJ-11 (modem) jack
Connects a modem cable.
(4)
Vent
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(5)
External monitor port
Connects an external VGA monitor or projector.
(6)
Power connector
Connects an AC adapter.
(7)
RJ-45 (network) jack
Connects a network cable.
(8)
USB ports (3)
Connect optional USB devices.
Left-side components
11
Bottom components
Item
Component
Function
(1)
Battery bay
Holds the battery.
(2)
Battery release latches (2)
Release the battery from the battery bay.
(3)
Memory module compartment
Contains 2 memory module slots.
(4)
Vents (4)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(5)
Hard drive bay
Holds the hard drive.
(6)
WLAN module compartment (select models only)
Contains a WLAN module slot.
CAUTION: To prevent an unresponsive system, use
only a wireless module authorized for use in the
computer by the governmental agency that regulates
wireless devices in your country or region. If you install
the module and then receive a warning message, remove
the module to restore computer functionality, and then
contact technical support through Help and Support.
12
Chapter 2 External component identification
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model
number located on the bottom of the computer.
Serial number location
13
Computer major components
14
Chapter 3 Illustrated parts catalog
Item
Description
(1)
Display assemblies (include 2 WLAN antenna transceivers and cables)
Spare part number
14.1-inch, WXGA BrightView display assembly for use only with computer models equipped
with discrete graphics subsystem memory
456598-001
14.1-inch, WXGA display assembly for use only with computer models equipped with
discrete graphics subsystem memory
456597-001
14.1-inch, WXGA BrightView display assembly for use only with computer models equipped
with UMA graphics subsystem memory
456596-001
14.1-inch, WXGA display assembly for use only with computer models equipped with UMA
graphics subsystem memory
456595-001
Display internal components:
Display bezel
456620-001
Display enclosure (includes 2 WLAN antenna transceivers and cables)
456621-001
Display hinges (includes left and right hinges)
456619-001
Display inverter
456618-001
(2)
Switch cover (includes LED board and cable)
456592-001
(3)
Keyboards
For use in Japan
456624-291
For use in South Korea
456624-AD1
For use in Taiwan
456624-AB1
For use in Thailand
456624-281
For use in the United States
456624-001
(4)
Speaker
456593-001
(5)
Top cover
456599-001
Plastics Kit (see Plastics Kit on page 20 for more Plastics Kit spare part information):
456614-001
(6a)
ExpressCard slot bezel
(6b)
WLAN module compartment cover
(6c)
Memory module compartment cover
(6d)
Hard drive bay cover
TouchPad components
(7a)
TouchPad bracket (included in the TouchPad Miscellaneous Kit, which also includes the
TouchPad board cable and TouchPad button board actuators, which are not illustrated)
456602-001
(7b)
TouchPad board
456600-001
(8)
Fan
431312-001
(9)
TouchPad button board (includes cable)
456601-001
(10)
System boards (includes replacement thermal material and the ExpressCard assembly)
For use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 128-MB DDR2 discrete graphics system memory)
456613-001
Computer major components
15
Item
(11)
Description
Spare part number
For use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 64-MB DDR2 discrete graphics system memory)
456612-001
For use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 128-MB DDR1 discrete graphics system memory)
456611-001
For use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 64-MB DDR1 discrete graphics system memory)
456610-001
For use only with computer models equipped with Intel Core 2 Duo processors and UMA
graphics subsystem
456608-001
For use only with computer models equipped with Intel Celeron M processors and UMA
graphics subsystem
456609-001
Broadcom Bluetooth modules (do not include Bluetooth module cable)
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth module
cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 21 for more Cable Kit
spare part number information.
(12)
For use in all countries and regions except Japan and Asia Pacific countries and regions
398393-002
For use only in Japan and Asia Pacific countries and regions
450066-001
Heat sinks (include replacement thermal material)
For use only with computer models equipped with discrete graphics subsystem
456606-001
For use only with computer models equipped with UMA graphics subsystem
456605-001
Thermal Material Kits (not illustrated)
(13)
For use in all countries and regions except Japan and Asia Pacific countries and regions
413706-001
For use only in Japan and Asia Pacific countries and regions
445853-001
Processors (includes replacement thermal material)
Intel Core 2 Duo processors:
●
T9300 2.50-GHz (6-MB L2 cache, 800-MHz FSB)
463050-001
●
T8300 2.40-GHz (3-MB L2 cache, 800-MHz FSB)
463049-001
●
T8100 2.10-GHz (3-MB L2 cache, 800-MHz FSB)
463048-001
●
T7800 2.60-GHz (4-MB L2 cache, 800-MHz FSB)
459465-001
●
T7700 2.40-GHz (4-MB L2 cache, 800-MHz FSB)
446894-001
●
T7500 2.20-GHz (4-MB L2 cache, 800-MHz FSB)
446893-001
●
T7300 2.00-GHz (4-MB L2 cache, 800-MHz FSB)
446892-001
●
T7250 2.00-GHz (2-MB L2 cache, 800-MHz FSB)
459463-001
●
T7100 1.80-GHz (2-MB L2 cache, 800-MHz FSB)
446891-001
●
T5550 1.83-GHz (2-MB L2 cache, 800-MHz FSB)
459464-001
●
T5470 1.60-GHz (2-MB L2 cache, 800-MHz FSB)
456575-001
●
T5270 1.40-GHz (2-MB L2 cache, 800-MHz FSB)
462345-001
Intel Celeron M processors:
16
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
●
550 2.00-GHz (1-MB L2 cache, 533-MHz FSB)
446889-001
●
540 1.86-GHz (1-MB L2 cache, 533-MHz FSB)
446888-001
●
530 1.73-GHz (1-MB L2 cache, 533-MHz FSB)
459462-001
(14)
RTC battery
(15)
Modem modules
449137-001
NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable is
included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 21 for more Cable Kit spare part
number information.
For use only in the United States
441074-001
For use only in Japan and Asia Pacific countries and regions
449139-001
Base enclosure (includes rubber feet)
456603-001
Discrete base enclosure (includes rubber feet)
460702-001
Rubber Kit (not illustrated, contains 6 computer feet and 8 display bezel screw covers)
456616-001
(17)
6-cell, 47-Wh Li-ion battery
456623-001
(18)
WLAN modules
(16)
Intel 802.11a/b/g/n WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong,
India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan,
Uruguay, the United States, Venezuela, and Vietnam
441086-001
●
For use in Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
441086-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and
South Korea
441086-003
●
For use in Japan
441086-291
Broadcom 802.11a/b/g WLAN modules:
Computer major components
17
Item
Description
Spare part number
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican
Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the
Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia,
Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands,
New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of
Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe,
Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South
Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad
and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab
Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zaire, Zambia, and Zimbabwe
441075-002
●
For use in Japan
441075-291
Intel 802.11a/b/g WLAN modules:
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong,
India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan,
the United States, Uruguay, Venezuela, and Vietnam
441082-001 and
448674-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany,
Greece, Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein,
Lithuania, Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the
Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and Montenegro,
Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland,
Turkey, Ukraine, the United Kingdom, and Uzbekistan
441082-002 and
448674-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and
South Korea
441082-003 and
448674-003
●
For use in Japan
441082-291 and
448674-291
●
For use in South Korea
456576-AD1
Intel 802.11b/g WLAN module for use in Thailand
(19)
(20)
18
409280-004
Memory modules (PC2-5300, 667-MHz, DDR2)
2048-MB
417506-001
1024-MB
414046-001
512-MB
414045-001
Hard drives (include hard drive bracket)
Chapter 3 Illustrated parts catalog
Item
(21)
Description
Spare part number
160-GB, 5400-rpm
457014-001
120-GB, 5400-rpm
457013-001
80-GB, 5400-rpm
457012-001
Optical drives (include bezel and bracket)
DVD±RW and CD-RW Double-Layer Combo Drive with LightScribe
456799-001
DVD±RW and CD-RW Double-Layer Combo Drive
456798-001
DVD/CD-RW Combo Drive
456797-001
Cable Kit (not illustrated; see Cable Kit on page 21 for more Cable Kit spare part number
information)
457400-001
Computer major components
19
Plastics Kit
Item
20
Description
Spare part number
Plastics Kit:
456614-001
(1)
Hard drive bay cover (includes 2 captive screws, secured by C-clips)
(2)
WLAN module compartment cover (includes one captive screw, secured by a C-clip)
(3)
ExpressCard slot bezel
(4)
Memory module compartment cover (includes one captive screw, secured by a C-clip)
Chapter 3 Illustrated parts catalog
Cable Kit
Item
Description
Spare part number
Cable Kit:
457400-001
(1)
RJ-11 jack cable
(2)
Display lid switch module and cable
(3)
Bluetooth module cable
Cable Kit
21
Mass storage devices
Item
Description
(1)
Optical drives (include bezel and bracket)
(2)
22
Spare part number
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
456799-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
456798-001
DVD/CD-RW Combo Drive
456797-001
Hard drives (include bracket)
160-GB, 5400-rpm
457014-001
120-GB, 5400-rpm
457013-001
80-GB, 5400-rpm
457012-001
Chapter 3 Illustrated parts catalog
Miscellaneous parts
Description
Spare part number
AC adapters
90-W slimline AC adapter (for use only with computer models with discrete graphics system
memory)
458220-001
65-W AC adapter (for use only with computer models with UMA graphics system memory)
417220-001
Logo Kit
456617-001
Nylon carrying case
325814-001
USB 1.1 diskette drive
359118-001
Power cords:
For use in Australia
246959-011
For use the United States
246959-001
Screw Kit
456615-001
●
Phillips PM3.0×4.0 screw
●
Phillips PM2.5×12.0 captive screw
●
Phillips PM2.5×10.0 captive screw
●
Phillips PM2.5×7.0 captive screw
●
Phillips PM2.5×7.0 screw
●
Phillips PM2.5×4.0 screw
●
Phillips PM2.0×8.0 screw
●
Phillips PM2.0×6.0 screw
●
Phillips PM2.0×5.0 captive screw
●
Phillips PM2.0×4.0 screw
●
Phillips PM2.0×2.0 broad-head screw
●
Torx T8M2.5×9.0 screw
●
Torx T8M2.5×7.0 screw
●
Torx T8M2.5×6.0 screw
●
Torx T8M2.5×4.0 screw
●
Torx T8M2.5×3.0 broad-head screw
●
Torx T8M2.0×4.0 screw
Miscellaneous parts
23
Sequential part number listing
Spare part
number
Description
246959-001
Power cord for use in the United States
246959-011
Power cord for use in Australia and New Zealand
398393-002
Bluetooth module for use in North America
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 21 for
more Cable Kit spare part number information.
409280-004
Intel 802.11b/g WLAN module for use in Thailand
413706-001
Thermal Material Kit for use only in the United States
414045-001
512-MB memory module (PC2-5300, 667-MHz, DDR2)
414046-001
1024-MB memory module (PC2-5300, 667-MHz, DDR2)
417220-001
65-W AC adapter (for use only with computer models with UMA graphics system memory)
417506-001
2048-MB memory module (PC2-5300, 667-MHz, DDR2)
431312-001
Fan
441074-001
Modem module for use only in the United States (includes modem module cable)
NOTE: The modem module spare part kits do not include a modem module cable. The modem module
cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 21 for more Cable
Kit spare part number information.
24
441075-002
Broadcom 802.11a/b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua
and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti,
Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana,
Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,
Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique,
Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria,
Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland,
Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe,
Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia,
Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St.
Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United
Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire,
Zambia, and Zimbabwe
441075-291
Broadcom 802.11a/b/g WLAN module for use in Japan
441082-001
Intel 802.11a/b/g WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
Chapter 3 Illustrated parts catalog
Spare part
number
Description
441082-002
Intel 802.11a/b/g WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia,
Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden,
Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
441082-003
Intel 802.11a/b/g WLAN module for use in Australia, New Zealand, Pakistan, the People's Republic of
China, and South Korea
441082-291
Intel 802.11a/b/g WLAN module for use in Japan
441086-001
Intel 802.11a/b/g/n WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
441086-002
Intel 802.11a/b/g/n WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia,
Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden,
Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
441086-003
Intel 802.11a/b/g/n WLAN module for use in Australia, New Zealand, Pakistan, the People's Republic of
China, and South Korea
441086-291
Intel 802.11a/b/g/n WLAN module for use in Japan
441090-002
Broadcom 802.11b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the
Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo,
Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic,
East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France,
French Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,
Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland,
Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi,
Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether
Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau,
Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and
Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia,
Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
441090-291
Broadcom 802.11b/g WLAN module for use in Japan
445853-001
Thermal Material Kit for use only in Japan and Asia Pacific countries and regions
446888-001
Intel Celeron M 540 1.86-GHz processor (1-MB L2 cache, 533-MHz FSB, includes replacement thermal
material)
446889-001
Intel Celeron M 550 2.00-GHz processor (1-MB L2 cache, 533-MHz FSB, includes replacement thermal
material)
446891-001
Intel Core 2 Duo T7100 1.80-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
Sequential part number listing
25
Spare part
number
Description
446892-001
Intel Core 2 Duo T7300 2.00-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
446893-001
Intel Core 2 Duo T7500 2.20-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
446894-001
Intel Core 2 Duo T7700 2.40-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
448674-001
Intel 802.11a/b/g WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
448674-002
Intel 802.11a/b/g WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia,
Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden,
Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
448674-003
Intel 802.11a/b/g WLAN module for use in Australia, New Zealand, Pakistan, the People's Republic of
China, and South Korea
448674-291
Intel 802.11a/b/g WLAN module for use in Japan
449137-001
RTC battery
449139-001
Modem module for use only in Japan and Asia Pacific countries and regions (includes modem module
cable)
NOTE: The modem module spare part kits do not include a modem module cable. The modem module
cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 21 for more Cable
Kit spare part number information.
450066-001
Bluetooth module for use in Japan and Asia Pacific countries and regions
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 21 for
more Cable Kit spare part number information.
26
456575-001
Intel Core 2 Duo T5470 1.60-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
456576-AD1
Intel 802.11a/b/g WLAN module for use in South Korea
456592-001
Switch cover (includes LED board and cable)
456593-001
Speaker
456595-001
14.1-inch, WXGA display assembly for use only with computer models equipped with UMA graphics
subsystem (includes 2 WLAN antenna transceivers and cables)
456596-001
14.1-inch, WXGA display assembly with BrightView for use only with computer models equipped with UMA
graphics subsystem (includes 2 WLAN antenna transceivers and cables)
456597-001
14.1-inch, WXGA display assembly for use only with computer models equipped with discrete graphics
subsystem (includes 2 WLAN antenna transceivers and cables)
456598-001
14.1-inch, WXGA display assembly with BrightView for use only with computer models equipped with
discrete graphics subsystem (includes 2 WLAN antenna transceivers and cables)
456599-001
Top cover
456600-001
TouchPad board
Chapter 3 Illustrated parts catalog
Spare part
number
Description
456601-001
TouchPad button board (includes cable)
456602-001
TouchPad Miscellaneous Kit (includes TouchPad board cable, TouchPad bracket, and TouchPad button
board actuators)
456603-001
Base enclosure (includes rubber feet)
456605-001
Heat sink for use only with computer models equipped with UMA graphics subsystem (includes replacement
thermal material)
456606-001
Heat sink for use only with computer models equipped with discrete graphics subsystem (includes
replacement thermal material)
456608-001
System board for use only with computer models equipped with Intel Core 2 Duo processors and UMA
graphics subsystem (includes replacement thermal material and the ExpressCard assembly)
456609-001
System board for use only with computer models equipped with Intel Celeron M processors and UMA
graphics subsystem (includes replacement thermal material and the ExpressCard assembly)
456610-001
System board for use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 64-MB DDR1 discrete graphics system memory, replacement thermal
material, and the ExpressCard assembly)
456611-001
System board for use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 128-MB DDR1 discrete graphics system memory, replacement thermal
material, and the ExpressCard assembly)
456612-001
System board for use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 64-MB DDR2 discrete graphics system memory, replacement thermal
material, and the ExpressCard assembly)
456613-001
System board for use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 128-MB DDR2 discrete graphics system memory, replacement thermal
material, and the ExpressCard assembly)
456614-001
Plastics Kit (see Plastics Kit on page 20 for more Plastics Kit spare part information)
456615-001
Screw Kit
456616-001
Rubber Kit (contains 6 computer feet and 8 display bezel screw covers)
456617-001
Logo Kit
456618-001
Display inverter
456619-001
Display hinges (includes left and right hinges)
456620-001
Display bezel
456621-001
Display enclosure (includes 2 wireless antenna transceivers and cables)
456623-001
6-cell, 47-Wh Li-ion battery
456624-001
Keyboard for use in the United States
456624-281
Keyboard for use in Thailand
456624-291
Keyboard for use in Japan
456624-AB1
Keyboard for use in Taiwan
456624-AD1
Keyboard for use in South Korea
456797-001
DVD/CD-RW Combo Drive (includes bezel and bracket)
456798-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive (includes bezel and bracket)
Sequential part number listing
27
28
Spare part
number
Description
456799-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe (includes bezel and
bracket)
457012-001
80-GB, 5400-rpm hard drive (includes bracket)
457013-001
120-GB, 5400-rpm hard drive (includes bracket)
457014-001
160-GB, 5400-rpm hard drive (includes bracket)
457400-001
Cable Kit (see Cable Kit on page 21 for more Cable Kit spare part information)
458220-001
90-W slimline AC adapter (for use only with computer models with discrete graphics system memory)
459462-001
Intel Celeron M 530 1.73-GHz processor (1-MB L2 cache, 533-MHz FSB, includes replacement thermal
material)
459463-001
Intel Core 2 Duo T7250 2.00-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
459464-001
Intel Core 2 Duo T5550 1.83-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
459465-001
Intel Core 2 Duo T7800 2.60-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
460702-001
Discrete base enclosure (includes rubber feet)
462345-001
Intel Core 2 Duo T5270 1.40-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
463048-001
Intel Core 2 Duo T8100 2.10-GHz processor (3-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
463049-001
Intel Core 2 Duo T8300 2.40-GHz processor (3-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
463050-001
Intel Core 2 Duo T9300 2.50-GHz processor (6-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
Chapter 3 Illustrated parts catalog
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Flat-bladed screwdriver
●
Magnetic screwdriver
●
Phillips P0 and P1 screwdrivers
●
Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance
instructions.
Preliminary replacement requirements
29
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to
unseat or seat the cables during removal and insertion. Handle cables by the connector whenever
possible. In all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in
such a way that they cannot be caught or snagged by parts being removed or replaced. Handle flex
cables with extreme care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to
the computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the
computer is off or in Hibernation, turn the computer on, and then shut it down through the operating
system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and
be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a staticproof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
30
Chapter 4 Removal and replacement procedures
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some
protection, but in many cases, ESD contains enough power to alter device parameters or melt
silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you area ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines
described in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Preliminary replacement requirements
31
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or
packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive
foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials
are selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
32
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded
tools and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Chapter 4 Removal and replacement procedures
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible
straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper
ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug
connectors, use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive strips
must be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Preliminary replacement requirements
33
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the
password:
NOTE:
These steps also clear CMOS.
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the real-time clock (RTC) battery (see RTC battery on page 78).
6.
Wait approximately 5 minutes.
7.
Replace the RTC battery and reassemble the computer.
8.
Connect AC power to the computer. Do not reinsert any batteries at this time.
9.
Turn on the computer.
All passwords and all CMOS settings have been cleared.
34
Chapter 4 Removal and replacement procedures
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 76 screws, in 16 different sizes, that must be removed, replaced, or loosened
when servicing the computer. Make special note of each screw size and location during removal and
replacement.
Serial number
Report the computer serial number to HP when requesting information or ordering spare parts. The
serial number is located on the bottom of the computer.
Component replacement procedures
35
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare
part number 456616-001. There are 6 rubber feet that attach to the base enclosure in the locations
illustrated below.
36
Chapter 4 Removal and replacement procedures
Battery
Description
Spare part number
6-cell, 47-Wh Li-ion battery
456623-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
Remove the battery:
1.
Turn the computer upside down on a flat surface, with the battery bay toward you.
2.
Slide the battery release latches (1) to release the battery.
3.
Remove the battery (2) from the computer.
Install the battery by inserting it into the battery bay until you hear a click.
Component replacement procedures
37
Hard drive
NOTE: All hard drive spare part kits include a hard drive bracket.
Description
Spare part number
160-GB, 5400-rpm hard drive
457014-001
120-GB, 5400-rpm hard drive
457013-001
80-GB, 5400-rpm hard drive
457012-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Remove the hard drive:
38
1.
Position the computer with the front toward you.
2.
Loosen the two Phillips PM2.0×5.0 captive screws (1) that secure the hard drive bay cover to the
computer.
3.
Lift the right side of the hard drive bay cover (2), swing it to left, and remove the cover. The hard
drive bay cover is included in the Plastics Kit, spare part number 456614-001.
4.
Loosen the Phillips PM2.5×12.0 captive screw (1) that secures the hard drive to the computer.
5.
Grasp the Mylar tab (2) on the hard drive and slide the hard drive (3) to the left to disconnect it
from the system board.
Chapter 4 Removal and replacement procedures
6.
Remove the hard drive (4) from the hard drive bay.
7.
If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive
bracket screws (1) from each side of the hard drive.
8.
Lift the bracket (2) straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
Component replacement procedures
39
WLAN module
Description
Spare part number
Intel 802.11a/b/g/n WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia,
Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United
States, Venezuela, and Vietnam
441086-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar,
Romania, Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa,
Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and
Uzbekistan
441086-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South
Korea
441086-003
●
For use in Japan
441086-291
Broadcom 802.11a/b/g WLAN modules:
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's
Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech
Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador,
Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French
Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong,
Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali,
Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco,
Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau,
Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the
Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe,
Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri
Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia,
Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United
Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and
Zimbabwe
441075-002
●
For use in Japan
441075-291
Intel 802.11a/b/g WLAN modules:
●
40
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia,
Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States,
Uruguay, Venezuela, and Vietnam
Chapter 4 Removal and replacement procedures
441082-001 and
448674-001
Description
Spare part number
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar,
Romania, Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa,
Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and
Uzbekistan
441082-002 and
448674-002
●
For use in Australia, New Zealand, Pakistan, the People's Republic of China, and South
Korea
441082-003 and
448674-003
●
For use in Japan
441082-291 and
448674-291
●
For use in South Korea:
456576-AD1
Broadcom 802.11b/g WLAN modules:
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia &
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark,
Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,
Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon,
Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala,
Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya,
Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein,
Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali,
Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco,
Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles,
the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Palau, Panama,
Papua New Guinea, Paraguay, the People's Republic of China, Peru, the Philippines,
Poland, Portugal, Qatar, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San
Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the
Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia,
South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent &
Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Thailand, Togo, Tonga, Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda,
Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
441090-002
●
For use in Japan
441090-291
Intel 802.11b/g WLAN module for use in Thailand
409280-004
Before removing the WLAN module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Component replacement procedures
41
Remove the WLAN module:
1.
Position the computer with the front toward you.
2.
Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the WLAN module compartment
cover to the computer.
3.
Lift the right side of the WLAN module compartment cover (2), swing it to left, and remove the
cover. The WLAN module compartment cover is included in the Plastics Kit, spare part number
456614-001.
4.
Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal.
The white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
5.
Remove the two Phillips PM2.5×4.0 screws (2) that secure the WLAN module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
6.
Remove the WLAN module (3) by pulling the module away from the slot at an angle.
NOTE: WLAN modules are designed with a notch (4) to prevent incorrect installation.
42
Chapter 4 Removal and replacement procedures
Reverse this procedure to install the WLAN module.
Memory module
Description
Spare part number
2048-MB (PC2-5300, 667-MHz, DDR2)
417506-001
1024-MB (PC2-5300, 667-MHz, DDR2)
414046-001
512-MB (PC2-5300, 667-MHz, DDR2)
414045-001
Before removing the memory module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Remove the memory module:
1.
Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the memory module compartment
cover to the computer.
2.
Lift the front edge of the cover (2), swing it up and back, and remove the cover. The memory
module compartment cover is included in the Plastics Kit, spare part number 456614-001.
3.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
Component replacement procedures
43
4.
Remove the memory module (2) by pulling the module away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect installation into the
memory module slot.
Reverse this procedure to install a memory module.
44
Chapter 4 Removal and replacement procedures
Optical drive
NOTE:
All optical drive spare part kits include an optical drive bezel.
Description
Spare part number
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
456799-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
456798-001
DVD/CD-RW Combo Drive
456797-001
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Remove the optical drive:
1.
Position the computer with the right side toward you.
2.
Remove the Torx T8M2.5×7.0 screw (1) that secures the optical drive to the computer.
3.
Insert a flat-bladed screwdriver or similar tool into the optical drive tab access (2) and press the
tab to the left to release the optical drive from the computer.
4.
Remove the optical drive (3) from the computer.
5.
If it is necessary to replace the optical drive bracket, position the optical drive with the rear
toward you.
6.
Remove the two Phillips PM2.0×4.0 screws (1) that secure the optical drive bracket to the optical
drive.
Component replacement procedures
45
7.
Remove the optical drive bracket (2).
Reverse this procedure to reassemble and install an optical drive.
46
Chapter 4 Removal and replacement procedures
Switch cover and keyboard
Description
Spare part number
Switch cover (includes button board and cable)
456581-001
Keyboards for use in the following countries or regions:
Belgium
456587-181
Norway
456587-091
The Czech Republic
456587-221
Portugal
456587-131
Denmark
456587-081
Russia
456587-251
France
456587-051
Saudi Arabia
456587-171
French Canada
456587-121
Slovakia
456587-231
Germany
456587-041
Slovenia
456587-BA1
Greece
456587-DJ1
Spain
456587-071
Hungary
456587-211
Sweden and Finland
456587-B71
Iceland
456587-DD1
Switzerland
456587-BG1
Israel
456587-BB1
Turkey
456587-141
Italy
456587-061
The United Kingdom
456587-031
The Netherlands
456587-B31
The United States
456587-001
Before removing the switch cover and keyboard, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
Component replacement procedures
47
Remove the switch cover and keyboard:
1.
Remove the following screws:
(1) Two Torx T8M2.5×7.0 screws
(2) Three Torx T8M2.5×3.0 broad-head screws
48
2.
Remove the two Torx T8M2.5×7.0 screws that secure the keyboard to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
Chapter 4 Removal and replacement procedures
5.
Lift the switch cover (1) straight up until it disengages from the computer, and slide it back (2)
until it rests on the display assembly.
6.
Lift the rear edge of the keyboard (1) until it rests at an angle, and slide it back (2) until it rests on
the display assembly and switch cover.
Component replacement procedures
49
7.
Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and
disconnect the keyboard cable (2) from the system board.
8.
Remove the keyboard.
9.
Release the ZIF connector (1) to which the button board cable is attached, and disconnect the
button board cable (2) from the system board.
10. Remove the switch cover.
Reverse this procedure to install the switch cover and keyboard.
50
Chapter 4 Removal and replacement procedures
Speaker
Description
Spare part number
Speaker
456593-001
Before removing the speaker, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the keyboard (see Switch cover and keyboard on page 47).
6.
Remove the switch cover (see Switch cover and keyboard on page 47).
Remove the speaker:
1.
Disconnect the speaker cable (1) from the system board.
2.
Remove the two Torx T8M2.5×4.0 screws (2) that secure the speaker to the top cover.
3.
Remove the speaker (3) from the top cover.
Reverse this procedure to install the speaker.
Component replacement procedures
51
Display lid switch module
NOTE: The display lid switch module is included in the Cable Kit, spare part number Cable Kit,
spare part number 457400-001.
Before removing the display lid switch module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the keyboard (see Switch cover and keyboard on page 47).
6.
Remove the switch cover (see Switch cover and keyboard on page 47).
Remove the display lid switch module:
1.
Disconnect the display lid switch module cable (1) from the system board.
2.
Remove the display lid switch module (2) from the clip built into the top cover.
3.
Remove the display lid switch module cable from the clips (3) built into the top cover.
Reverse this procedure to install the display lid switch module.
52
Chapter 4 Removal and replacement procedures
Display assembly
NOTE:
All display assembly spare part kits include 2 WLAN antenna transceivers and cables.
Description
Spare part number
14.1-inch, WXGA BrightView display assembly for use only with computer models equipped with
discrete graphics subsystem memory
456598-001
14.1-inch, WXGA display assembly for use only with computer models equipped with discrete
graphics subsystem memory
456597-001
14.1-inch, WXGA BrightView display assembly for use only with computer models equipped with
UMA graphics subsystem memory
456596-001
14.1-inch, WXGA display assembly for use only with computer models equipped with UMA
graphics subsystem memory
456595-001
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Disconnect the wireless antenna cables from the WLAN module (see WLAN module
on page 40).
6.
Remove the following components:
a.
Keyboard (see Switch cover and keyboard on page 47)
b.
Switch cover (see Switch cover and keyboard on page 47)
c.
Speaker (see Speaker on page 51)
d.
Display lid switch module (see Display lid switch module on page 52)
Remove the display assembly:
1.
Close the computer and turn it upside down, with the rear panel toward you.
Component replacement procedures
53
54
2.
Remove the two Torx T8M2.5×7.0 screws that secure the display assembly to the computer.
3.
Turn the computer right-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Disconnect the display panel cables (1) and (2) from the system board.
6.
Remove the wireless antenna cables (3) from the clips and routing channels built into the top
cover.
7.
Remove the two T8M2.5×7.0 screws (1) that secure the display assembly to the computer.
Chapter 4 Removal and replacement procedures
8.
Lift the display assembly (2) straight up and remove it.
9.
If it is necessary to replace the display bezel, display inverter, or display hinges, remove the
eight rubber screw covers (1) and the eight Torx T8M2.5×6.0 screws (2) that secure the display
bezel to the display assembly. The rubber screw covers are available in the Rubber Kit, spare
part number 456616-001.
10. Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the
display bezel until the bezel disengages from the display enclosure.
Component replacement procedures
55
11. Remove the display bezel (3). The display bezel is available using spare part number
456620-001.
12. If it is necessary to replace the display inverter, remove the inverter (1) from the display
enclosure as far as the display panel cable and the backlight cable will allow.
13. Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
14. Remove the display inverter. The display inverter is available using spare part number
456618-001.
15. If it is necessary to replace the display hinges, remove the two Torx T8M2.5×6.0 screws (1) that
secure the display panel to the display enclosure.
56
Chapter 4 Removal and replacement procedures
16. Remove the display panel (2).
17. Remove the four Phillips PM2.0×4.0 screws (1) that secure each display hinge to the display
panel.
18. Remove the display hinges (2). The left and right display hinges are available using spare part
number 456619-001.
Reverse this procedure to reassemble and install the display assembly.
Component replacement procedures
57
Top cover
Description
Spare part number
Top cover
456599-001
Before removing the top cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
Remove the top cover:
1.
58
Turn the computer upside down, with the front toward you.
Chapter 4 Removal and replacement procedures
2.
Remove the followng screws:
(1) Three Phillips PM2.0×2.0 broad-head screws
(2) Seven Torx T8M2.5×7.0 screws
(3) One Torx T8m2.5×4.0 screw
3.
Turn the computer right-side up, with the left side toward you.
4.
Press in on the ExpressCard slot eject button (1) two times. The first press releases the
ExpressCard slot eject button. The second press releases the ExpressCard slot bezel from the
ExpressCard slot.
5.
Remove the ExpressCard slot bezel (2).
6.
Remove the two Torx T8M2.5×7.0 screws (3) that secure the top cover to the computer.
7.
Lift the rear edge of the top cover (1) and swing it up and forward until it rests at an angle.
8.
Lift the front edge of the top cover (2) until it disengages from the base enclosure.
9.
Tilt the top cover (3) back until the TouchPad cable is accessible.
Component replacement procedures
59
10. Release the ZIF connector (4) to which the TouchPad cable is connected and disconnect the
TouchPad cable from the system board.
11. Remove the top cover.
Reverse this procedure to install the top cover.
60
Chapter 4 Removal and replacement procedures
TouchPad board and TouchPad button board
Description
Spare part number
TouchPad board
456600-001
TouchPad button board (includes cable)
456601-001
TouchPad Miscellaneous Kit (includes TouchPad board cable, TouchPad bracket, and TouchPad
button board actuators)
456602-001
Before removing the TouchPad board and TouchPad button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
Remove the TouchPad board and TouchPad button board:
1.
Turn the top cover upside down, with the front toward you.
2.
Release the ZIF connectors on the TouchPad button board (1) and TouchPad board (2) to which
the TouchPad board cable is connected.
3.
Disconnect and remove the TouchPad board cable (3).
Component replacement procedures
61
62
4.
Remove the two Phillips PM2.0×4.0 screws (4) that secure the TouchPad bracket to the
computer.
5.
Release the TouchPad bracket (1) by sliding it back.
6.
Remove the TouchPad bracket (2) by lifting it straight up.
7.
Remove the TouchPad button board (3).
8.
Remove the TouchPad button board cable (4) from the opening in the TouchPad bracket.
Chapter 4 Removal and replacement procedures
9.
Remove the TouchPad board (1) from the top cover.
NOTE: When replacing the TouchPad board and TouchPad button board, be sure the
TouchPad button actuators (2) are installed in the top cover.
Reverse this procedure to install the TouchPad board and TouchPad button board.
Component replacement procedures
63
Bluetooth module
NOTE: The Bluetooth module spare part kits do not include a Bluetooth module cable. The
Bluetooth module cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit
on page 21 for more Cable Kit spare part number information.
Description
Spare part number
For use in all countries and regions except Japan and Asia Pacific countries and regions
398393-001
For use only Japan and Asia Pacific countries and regions
450066-001
Before removing the Bluetooth module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
Remove the Bluetooth module:
64
1.
Disconnect the Bluetooth module cable (1) from the system board.
2.
Remove the two Phillips PM2.0×4.0 screws (2) that secure the Bluetooth module to the base
enclosure.
Chapter 4 Removal and replacement procedures
3.
Remove the Bluetooth module (3) from the base enclosure.
Reverse this procedure to install the Bluetooth module.
Component replacement procedures
65
System board
NOTE:
All system board spare part kits include the ExpressCard assembly.
NOTE: All system board spare part kits include replacement thermal material. Replacement thermal
material is also available in the Thermal Material Kit, spare part numbers 413706-001 (for use only in
the United States) and 445853-001 (for use only in Japan and Asia Pacific countries and regions).
Description
Spare part number
For use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 128-MB DDR2 discrete graphics system memory)
456613-001
For use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 64-MB DDR2 discrete graphics system memory)
456612-001
For use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 128-MB DDR1 discrete graphics system memory)
456611-001
For use only with computer models equipped with Intel Core 2 Duo processors and discrete
graphics subsystem (includes 64-MB DDR1 discrete graphics system memory)
456610-001
For use only with computer models equipped with Intel Core 2 Duo processors and UMA graphics
subsystem
456608-001
For use only with computer models equipped with Intel Celeron M processors and UMA graphics
subsystem
456609-001
Before removing the system board, follow these steps:
66
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
Chapter 4 Removal and replacement procedures
When replacing the system board, be sure that the following components are removed from the
defective system board and installed on the replacement system board:
●
Memory module (see Memory module on page 43)
●
WLAN module (see WLAN module on page 40)
●
Processor (see Processor on page 74)
Remove the system board:
1.
Remove the RJ-11 jack (1) from the clip built into the base enclosure and remove the RJ-11 jack
cable from the hook (2) built into the base enclosure.
2.
Disconnect the fan cable (3) and the Bluetooth module cable (4) from the system board.
3.
Remove the Phillips PM2.0×6.0 screw (1) and the Torx T8M2.5×4.0 screw (2) that secure the
system board to the base enclosure.
4.
Flex the left side of the base enclosure (1) until the external monitor connector (2) is clear of the
opening in the base enclosure.
5.
Lift the rear edge of the system board (3) until it rests at an angle.
Component replacement procedures
67
6.
Remove the system board (4) from the base enclosure by sliding it back.
Reverse the preceding procedure to install the system board.
68
Chapter 4 Removal and replacement procedures
Fan
Description
Spare part number
Fan
431312-001
Before removing the fan, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the fan:
1.
Remove the Phillips PM2.5×7.0 screw (1) that secures the fan to the base enclosure.
2.
Loosen the Phillips PM2.5×7.0 screw (2) that secures the fan to the base enclosure.
Component replacement procedures
69
3.
Remove the fan (3) from the base enclosure.
Reverse this procedure to install the fan.
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side
of the computer.
The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is
designed to turn on automatically when high temperature conditions exist. These conditions are
affected by high external temperatures, system power consumption, power management/battery
conservation configurations, battery fast charging, and software requirements. Exhaust air is
displaced through the ventilation grill located on the left side of the computer.
70
Chapter 4 Removal and replacement procedures
Heat sink
NOTE: The heat sink spare part kits include replacement thermal material. Replacement thermal
material is also available in the Thermal Material Kit, spare part numbers 413706-001 (for use only in
the United States) and 445853-001 (for use only in Japan and Asia Pacific countries and regions).
Description
Spare part number
For use only with computer models equipped with discrete graphics subsystem
456606-001
For use only with computer models equipped with UMA graphics subsystem
456605-001
Before removing the heat sink, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the heat sink:
1.
Turn the system board upside down, with the USB connectors toward you.
NOTE: Steps 2 and 3 apply only to computer models equipped with graphics subsystems
having discrete memory. See steps 4 and 5 for removing the heat sink on computer models with
graphics subsystems having UMA memory.
2.
Following the 1, 2, 3, 4, 5, 6 sequence stamped into the heat sink, loosen the six Phillips
PM2.5×10.0 screws (1) that secure the heat sink to the system board.
Component replacement procedures
71
3.
Remove the heat sink (2).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink (1),
(2), and (3), and the system board components (4), (5), and (6) each time the heat sink is
removed. Replacement thermal material is included with all heat sink, system board, and
processor spare part kits.
NOTE: Steps 4 and 5 apply only to computer models equipped with graphics subsystems with
UMA memory.
4.
72
Following the 1, 2, 3, 4, sequence stamped into the heat sink, loosen the four Phillips
PM2.5×10.0 screws (1) that secure the heat sink to the system board.
Chapter 4 Removal and replacement procedures
5.
Remove the heat sink (2).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink (1)
and (2), and the system board (3) and (4) each time the heat sink is removed. Replacement
thermal material is included with all heat sink, system board, and processor spare part kits.
Reverse this procedure to install the heat sink.
Component replacement procedures
73
Processor
NOTE: All processor spare part kits include replacement thermal material. Replacement thermal
material is also available in the Thermal Material Kit, spare part numbers 413706-001 (for use only in
the United States) and 445853-001 (for use only in Japan and Asia Pacific countries and regions).
Description
Spare part number
Intel Core 2 Duo processors
●
T9300 2.50-GHz processor (6-MB L2 cache, 800-MHz FSB)
463050-001
●
T8300 2.40-GHz processor (3-MB L2 cache, 800-MHz FSB)
463049-001
●
T8100 2.10-GHz processor (3-MB L2 cache, 800-MHz FSB)
463048-001
●
T7800 2.60-GHz processor (4-MB L2 cache, 800-MHz FSB)
459465-001
●
T7700 2.40-GHz processor (4-MB L2 cache, 800-MHz FSB)
446894-001
●
T7500 2.20-GHz processor (4-MB L2 cache, 800-MHz FSB)
446893-001
●
T7300 2.00-GHz processor (4-MB L2 cache, 800-MHz FSB)
446892-001
●
T7250 2.00-GHz processor (2-MB L2 cache, 800-MHz FSB)
459463-001
●
T7100 1.80-GHz processor (2-MB L2 cache, 800-MHz FSB)
446891-001
●
T5550 1.83-GHz processor (2-MB L2 cache, 800-MHz FSB)
459464-001
●
T5470 1.60-GHz processor (2-MB L2 cache, 800-MHz FSB)
456575-001
●
T5270 1.40-GHz processor (2-MB L2 cache, 800-MHz FSB)
462345-001
Intel Celeron M processors
●
550 2.00-GHz processor (1-MB L2 cache, 533-MHz FSB)
446889-001
●
540 1.86-GHz processor (1-MB L2 cache, 533-MHz FSB)
446888-001
●
530 1.73-GHz processor (1-MB L2 cache, 533-MHz FSB)
459462-001
Before removing the processor, follow these steps:
74
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
Chapter 4 Removal and replacement procedures
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the processor:
1.
Turn the system board upside down, with the USB connectors toward you.
2.
Use a flat-bladed screwdriver to turn the processor locking screw (1) one-half turn
counterclockwise until you hear a click.
3.
Lift the processor (2) straight up and remove it.
NOTE: When you install the processor, the gold triangle (3) on the processor must be aligned
with the triangle (4) embossed on the processor slot.
Reverse this procedure to install the processor.
Component replacement procedures
75
Modem module
NOTE: The modem module spare part kits do not include a modem module cable. The modem
module cable is included in the Cable Kit, spare part number 457400-001. See Cable Kit on page 21
for more Cable Kit spare part number information.
Description
Spare part number
For use only in the United States
441074-001
For use only in Japan and Asia Pacific countries and regions
449139-001
Before removing the modem module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the modem module:
76
1.
Turn the system board upside down, with the USB connectors toward you.
2.
Remove the two Phillips PM2.5×4.0 screws (1) that secure the modem module to the system
board.
Chapter 4 Removal and replacement procedures
3.
Lift the modem module (2) straight up to disconnect it from the system board.
4.
Remove the modem module.
Reverse this procedure to install the modem module.
Component replacement procedures
77
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all
passwords and CMOS settings to be cleared.
Description
Spare part number
RTC battery
449137-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 37).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 38)
b.
Optical drive (see Optical drive on page 45)
c.
Keyboard (see Switch cover and keyboard on page 47)
d.
Switch cover (see Switch cover and keyboard on page 47)
e.
Speaker (see Speaker on page 51)
f.
Display lid switch module (see Display lid switch module on page 52)
g.
Display assembly (see Display assembly on page 53)
h.
Top cover (see Top cover on page 58)
i.
System board (see System board on page 66)
Remove the RTC battery:
1.
78
Turn the system board upside down, with the audio connectors toward you.
Chapter 4 Removal and replacement procedures
2.
Remove the RTC battery from the socket on the system board.
Reverse this procedure to install the RTC battery.
Component replacement procedures
79
5
Computer Setup
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating
system is not working or will not load.
NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your
computer.
NOTE: Pointing devices are not supported in Computer Setup. You must use the keyboard to
navigate and make selections.
NOTE: An external keyboard connected by USB can be used with Computer Setup only if USB
legacy support is enabled.
To start Computer Setup:
80
1.
Turn on or restart the computer.
2.
Before Windows® opens and while the "F10 = ROM Based Setup" message is displayed in the
lower-left corner of the screen, press f10.
Chapter 5 Computer Setup
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics,
and System Configuration menus.
1.
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
Because Computer Setup is not Windows-based, it does not support the TouchPad. Navigation
and selection are by keystroke:
●
To choose a menu or a menu item, use the arrow keys.
●
To select an item, press enter.
●
To close open dialog boxes and return to the main Computer Setup screen, press esc.
●
To view navigation information, press f1.
●
To change the language, press f2.
2.
Select the File, Security, Diagnostics, or System Configuration menu.
3.
To exit Computer Setup, choose one of the following methods:
●
To exit Computer Setup without saving your preferences, use the arrow keys to select File
> Ignore Changes and Exit. Then follow the instructions on the screen.
●
To save your preferences and exit Computer Setup, use the arrow keys to select File >
Save Changes and Exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
Restoring factory settings in Computer Setup
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1.
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
2.
Use the arrow keys to select File > Restore defaults, and then press enter.
3.
When the confirmation dialog box opens, press f10.
4.
To save your preferences and exit Computer Setup, use the arrow keys to select File > Save
Changes and Exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory
settings.
Using Computer Setup
81
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by
your computer.
File menu
82
Select
To do this
System information
●
View identification information for the computer and the batteries in the
system.
●
View specification information for the processor, cache and memory size,
system ROM, video revision, and keyboard controller version.
Restore defaults
Replace the configuration settings in Computer Setup with the original factory
settings. (Password settings and security settings are not changed when you
restore the factory settings.)
Ignore changes and exit
Cancel any changes entered during the current session. Then exit and restart
the computer.
Save changes and exit
Save any changes entered during the current session. Then exit and restart the
computer. Your changes go into effect when the computer restarts.
Chapter 5 Computer Setup
Security menu
Select
To do this
Setup password
Enter, change, or delete a setup password.
Power-On password
Enter, change, or delete a power-on password.
Password options
●
Enable/disable stringent security.
●
Enable/disable password requirement on computer restart.
●
Enable/disable DriveLock on any computer hard drive.
●
Change a DriveLock user password or master password.
DriveLock passwords
NOTE: DriveLock settings are accessible only when you enter Computer
Setup by turning on (not restarting) the computer.
Smart Card security
Enable/disable support for smart card and Java™ Card power-on
authentication.
NOTE: Power-on authentication for smart cards is supported only on
computers with optional smart card readers.
NOTE:
TPM Embedded Security
You must have an administrator password to change this setting.
Enable/disable support for Trusted Platform Module (TPM) Embedded Security,
which protects the computer from unauthorized access to owner functions
available in Embedded Security for ProtectTools. For more information, refer to
the ProtectTools software Help.
NOTE:
You must have a setup password to change this setting.
System IDs
Enter user-defined computer asset tracking number and ownership tag.
Disk Sanitizer
Run Disk Sanitizer to destroy all existing data on the primary hard drive. The
following options are available:
●
Fast: Runs the Disk Sanitizer erase cycle once.
●
Optimum: Runs the Disk Sanitizer erase cycle 3 times.
●
Custom: Allows you to select the desired number of Disk Sanitizer erase
cycles from a list.
CAUTION: If you run Disk Sanitizer, the data on the primary hard drive is
destroyed permanently.
Diagnostics menu
Select
To do this
Hard Drive Self-Test options
Run a comprehensive self-test on any hard drive in the system.
Memory Check
Run a comprehensive check on system memory.
Startup Check (select models only)
Verify the system components needed for starting the computer.
Computer Setup menus
83
System Configuration menu
NOTE:
Some of the listed System Configuration options may not be supported by your computer.
Select
To do this
Language (or press f2)
Change the Computer Setup language.
Boot options
●
Set f9, f10, and f12 delay when starting up.
●
Enable/disable CD-ROM boot.
●
Enable/disable floppy boot.
●
Enable/disable internal network adapter boot and set the boot mode (PXE
or RPL).
●
Enable/disable MultiBoot, which sets a boot order that can include most
boot devices in the system.
●
Set the Express Boot Popup delay in seconds.
●
Set the boot order.
●
Swap the functions of the fn key and left ctrl key.
●
Enable/disable multiple standard pointing devices at startup. (To set the
computer to support only a single, usually nonstandard, pointing device at
startup, select Disable.)
●
Enable/disable USB legacy support. When enabled, USB legacy support
allows the following:
Device configurations
84
Chapter 5 Computer Setup
◦
Use of a USB keyboard, mouse, and hub in Computer Setup even
when a Windows operating system is not running.
◦
Startup from bootable USB devices, including a hard drive, diskette
drive, or optical drive connected by a USB port to the computer or to
an optional docking device (select models only).
●
Select a parallel port mode: EPP (Enhanced Parallel Port), standard,
bidirectional, or ECP (Enhanced Capabilities Port).
●
Enable/disable BIOS DMA data transfers.
●
Enable/disable fan always on while connected to an AC outlet.
●
Enable/disable Intel® Data Execution Prevention or AMD® PSAE
Execution Disable. When enabled, the processor can disable some virus
code execution, which helps to improve computer security.
●
Enable/disable LAN Power Save. When enabled, saves power by turning
off the LAN when not in use.
●
Enable/disable SATA Native Mode.
●
Enable/disable Dual Core CPU.
●
Enable/disable Secondary Battery Fast Charge.
●
Choose Bit-shift or LBA assisted HDD Translation Mode.
●
Enable/disable Windows direct application launcher.
●
Enable/disable HP Lockout.
Select
To do this
Built-In Device Options
●
Enable/disable embedded WWAN Device Radio.
●
Enable/disable embedded WLAN Device Radio.
●
Enable/disable embedded Bluetooth® Device Radio.
●
Enable/disable LAN/WLAN Switching. When enabled, switches to a WLAN
when a LAN is either unavailable or disconnected.
●
Enable/disable Wake on LAN from Off.
●
Enable/disable the ambient light sensor.
●
Enable/disable the serial port.
●
Enable/disable the parallel port.
●
Enable/disable the flash media reader.
●
Enable/disable the USB port.
Port Options
CAUTION: Disabling the USB port also disables MultiBay II devices and
ExpressCard devices on the advanced port replicator.
●
Enable/disable the 1394 port.
●
Enable/disable the cardbus slot.
●
Enable/disable the ExpressCard slot.
●
Enable/disable the infrared port.
●
Enable/disable the optical disk drive.
●
Enable/disable the network controller.
Computer Setup menus
85
6
Specifications
Computer specifications
Metric
U.S.
Depth
24.64 cm
9.70 in
Width
33.80 cm
13.31 in
Height (front to rear)
3.08 to 3.43 cm
1.21 to 1.35 in
Weight (equipped with optical drive, hard drive, and battery)
2.20 kg
4.85 lbs
Dimensions
Input power
Operating voltage
19.0 V dc @ 4.74 A – 90 W
Operating current
4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating (14.7 to 10.1 psia)
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating (14.7 to 4.4 psia)
-15 m to 12,192 m
-50 ft to 40,000 ft
Shock
Operating
125 g, 2 ms, half-sine
Nonoperating
200 g, 2 ms, half-sine
Random vibration
Operating
86
Chapter 6 Specifications
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep
rate
Metric
Nonoperating
U.S.
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within
this range of temperatures.
14.1-inch, WXGA display specifications
Metric
U.S.
Height
27.94 cm
11.0 in
Width
20.83 cm
8.2 in
Diagonal
35.56 cm
14.1 in
Number of colors
Up to 16.8 million
Contrast ratio
250:1 (typical)
Brightness
180 nits (typical)
Dimensions
Pixel resolution
Pitch
0.279 × 0.279 mm
Format
1280 × 800
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4.0 W
Viewing angle
+/-40 horizontal, +20/–40° vertical (typical)
14.1-inch, WXGA display specifications
87
Hard drive specifications
160-GB*
120-GB*
80-GB*
Height
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
Weight
101 g
101 g
101 g
Interface type
SATA
SATA
SATA
Transfer rate
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
Single track
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
Logical blocks
312,560,640
234,420,480
156,280,320
Disc rotational speed
5400 rpm
5400 rpm
5400 rpm
Dimensions
Seek times (typical read, including setting)
Operating temperature
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications may differ slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
88
Chapter 6 Specifications
DVD±RW and CD-RW Double-Layer Combo Drive
specifications
Applicable disc
Center hole diameter
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video CD),
Multisession CD (Photo-CD, CD-EXTRA,
Portfolio, CD-R, CD-RW), CD-R, CD-RW, DVDROM (DVD-5, DVD-9, DVD-10, DVD-18), DVDR, DVD-RW, DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
DVD+R, DVD+RW, DVD-R, DVDRW, DVD-RAM
1.5 cm (0.59 in)
Disc diameter
Standard disc
12 cm (4.72 in)
Mini disc
8 cm (3.15 in)
Disc thickness
1.2 mm (0.047 in)
Track pitch
0.74 µm
Access time
CD
DVD
Random
< 175 ms
< 230 ms
Full stroke
< 285 ms
< 335 ms
Audio output level
Line-out, 0.7 Vrms
Cache buffer
2 MB
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD-ROM
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
Startup time
< 15 seconds
Stop time
< 6 seconds
DVD±RW and CD-RW Double-Layer Combo Drive specifications
89
DVD/CD-RW Combo Drive specifications
Applicable disc
Center hole diameter
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video CD),
Multisession CD (Photo-CD, CD-EXTRA,
Portfolio, CD-R, CD-RW), CD-R, CD-RW, DVDROM (DVD-5, DVD-9, DVD-10, DVD-18), DVDR, DVD-RW, DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
1.5 cm (0.59 in)
Disc diameter
Standard disc
12 cm (4.72 in)
Mini disc
8 cm (3.15 in)
Disc thickness
1.2 mm (0.047 in)
Track pitch
0.74 µm
Access time
CD
DVD
Random
< 110 ms
< 130 ms
Full stroke
< 210 ms
< 225 ms
Audio output level
Line-out, 0.7 Vrms
Cache buffer
2 MB
Data transfer rate
90
24X CD-ROM
3,600 KB/sec
8X DVD
3,600 KB/sec
24X CD-R
3,600 KB/sec
24X CD-RW
3,600 KB/sec
Transfer mode
Multiword DMA mode 2
Startup time
< 15 seconds
Stop time
< 6 seconds
Chapter 6 Specifications
System DMA specifications
Hardware DMA
System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Available for ExpressCard
DMA6
Not assigned
DMA7
Not assigned
*ExpressCard controller can use DMA 1, 2, or 5.
System DMA specifications
91
System interrupt specifications
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the
serial port may assert IRQ3 or IRQ4.
92
Chapter 6 Specifications
System I/O address specifications
I/O address (hex)
System function (shipping configuration)
000 - 00F
DMA controller no. 1
010 - 01F
Unused
020 - 021
Interrupt controller no. 1
022 - 024
Opti chipset configuration registers
025 - 03F
Unused
02E - 02F
87334 “Super I/O” configuration for CPU
040 - 05F
Counter/timer registers
044 - 05F
Unused
060
Keyboard controller
061
Port B
062 - 063
Unused
064
Keyboard controller
065 - 06F
Unused
070 - 071
NMI enable/RTC
072 - 07F
Unused
080 - 08F
DMA page registers
090 - 091
Unused
092
Port A
093 - 09F
Unused
0A0 - 0A1
Interrupt controller no. 2
I/O Address (hex)
System Function (shipping configuration)
0A2 - 0BF
Unused
0C0 - 0DF
DMA controller no. 2
0E0 - 0EF
Unused
0F0 - 0F1
Coprocessor busy clear/reset
0F2 - 0FF
Unused
100 - 16F
Unused
170 - 177
Secondary fixed disk controller
178 - 1EF
Unused
1F0 - 1F7
Primary fixed disk controller
1F8 - 200
Unused
201
JoyStick (decoded in ESS1688)
202 - 21F
Unused
System I/O address specifications
93
94
I/O address (hex)
System function (shipping configuration)
220 - 22F
Entertainment audio
230 - 26D
Unused
26E - 26
Unused
278 - 27F
Unused
280 - 2AB
Unused
2A0 - 2A7
Unused
2A8 - 2E7
Unused
2E8 - 2EF
Reserved serial port
2F0 - 2F7
Unused
2F8 - 2FF
Infrared port
300 - 31F
Unused
320 - 36F
Unused
370 - 377
Secondary diskette drive controller
378 - 37F
Parallel port (LPT1/default)
380 - 387
Unused
388 - 38B
FM synthesizer—OPL3
38C - 3AF
Unused
3B0 - 3BB
VGA
3BC - 3BF
Reserved (parallel port/no EPP support)
3C0 - 3DF
VGA
3E0 - 3E1
ExpressCard controller in CPU
3E2 - 3E3
Unused
3E8 - 3EF
Internal modem
3F0 - 3F7
“A” diskette controller
3F8 - 3FF
Serial port (COM1/default)
CF8 - CFB
PCI configuration index register (PCIDIVO-1)
CFC - CFF
PCI configuration data register (PCIDIVO-1)
Chapter 6 Specifications
System memory map specifications
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
48 KB
000C0000-000CBFFF
Video BIOS
160 KB
000C8000-000E7FFF
Unused
64 KB
000E8000-000FFFFF
System BIOS
15 MB
00100000-00FFFFFF
Extended memory
58 MB
04800000-07FFFFFF
Super extended memory
58 MB
04800000-07FFFFFF
Unused
2 MB
08000000-080FFFFF
Video memory (direct access)
4 GB
08200000-FFFEFFFF
Unused
64 KB
FFFF0000-FFFFFFFF
System BIOS
System memory map specifications
95
7
Screw listing
This section provides specification and reference information for the screws and screw locks used in
the computer. All screws listed in this section are available in the Screw Kit, spare part number
456615-001.
96
Chapter 7 Screw listing
Phillips PM2.0×5.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
4
5.0 mm
2.0 mm
5.0 mm
Where used:
(1) Two captive screws that secure the hard drive bay cover to the computer (screws are captured on
the cover by C-clips)
(2) One captive screw that secures the WLAN module compartment cover to the computer (screw is
captured on the cover by a C-clip)
(3) One captive screw that secures the memory module compartment cover to the computer (screw is
captured on the cover by a C-clip)
Phillips PM2.0×5.0 captive screw
97
Phillips PM2.5×12.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
1
12.0 mm
2.5 mm
5.0 mm
Where used: One captive screw that secures the hard drive to the computer (screw is secured to the
hard drive bracket)
98
Chapter 7 Screw listing
Phillips PM3.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
4.0 mm
3.0 mm
5.0 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
Phillips PM3.0×4.0 screw
99
Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
4
4.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the WLAN module to the system board
Where used: 2 screws that secure the modem module to the system board
100 Chapter 7 Screw listing
Torx T8M2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
18
7.0 mm
2.5 mm
5.0 mm
Where used:
(1) One screw that secures the optical drive to the computer
(2) Two screws that secure the keyboard to the computer
(3) Two screws that secure the switch cover to the computer
Torx T8M2.5×7.0 screw 101
Where used: 2 screws that secure the display assembly to the computer
Where used: 2 screws that secure the display assembly to the computer
Where used: 7 screws that secure the top cover to the base enclosure
102 Chapter 7 Screw listing
Where used: 2 screws that secure the top cover to the base enclosure
Torx T8M2.5×7.0 screw 103
Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
16
4.0 mm
2.0 mm
4.5 mm
Where used: 2 screws that secure the optical drive bracket to the optical drive
Where used: 8 screws that secure the display hinges to the display assembly
104 Chapter 7 Screw listing
Where used: 2 screws that secure the TouchPad bracket and TouchPad button board to the top
cover
Where used: 2 screws that secure the Blueotooth module to the base enclosure
Where used: 2 screws that secure the ExpressCard assembly to the system board
Phillips PM2.0×4.0 screw 105
Torx T8M2.5×3.0 broad-head screw
Color
Quantity
Length
Thread
Head diameter
Black
2
3.0 mm
2.5 mm
8.0 mm
Where used: 2 screws that secure the switch cover to the computer
106 Chapter 7 Screw listing
Torx T8M2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
3
4.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the speaker to the computer
Where used: One screw that secures the top cover to the base enclosure
Torx T8M2.5×4.0 screw 107
Torx T8M2.5×6.0 screw
Color
Quantity
Length
Thread
Heat width
Black
9
6.0 mm
2.5 mm
5.0 mm
Where used: 8 screws that secure the display bezel to the display assembly
Where used: One screw that secures the system board to the base enclosure
108 Chapter 7 Screw listing
Phillips PM2.0×2.0 broad-head screw
Color
Quantity
Length
Thread
Head diameter
Black
3
2.0 mm
2.0 mm
7.0 mm
Where used: 3 screws that secure the top cover to the display enclosure
Phillips PM2.0×2.0 broad-head screw 109
Phillips PM2.0×6.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
1
6.0 mm
2.0 mm
4.5 mm
Where used: One screw that secures the system board to the base enclosure
110 Chapter 7 Screw listing
Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
1
7.0 mm
2.5 mm
5.0 mm
Where used: One screw that secures the fan to the base enclosure
Phillips PM2.5×7.0 screw 111
Phillips PM2.5×7.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
1
7.0 mm
2.5 mm
5.0 mm
Where used: One captive screw that secures the fan to the base enclosure (screw is secured to the
fan by a C-clip)
112 Chapter 7 Screw listing
Phillips PM2.5×10.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
6
10.0 mm
2.5 mm
5.0 mm
Where used: 6 captive screws that secure the heat sink to the system board on computer models
equipped with discrete graphics subsystem memory (screws are secured to the heat sink by C-clips)
Phillips PM2.5×10.0 captive screw 113
Where used: 4 captive screws that secure the heat sink to the system board on computer models
equipped with UMA graphics subsystem memory (screws are secured to the heat sink by C-clips)
114 Chapter 7 Screw listing
Phillips PM2.0×8.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
2
8.0 mm
2.0 mm
4.5 mm
Where used: 2 screws that secure the ExpressCard assembly to the system board
Phillips PM2.0×8.0 screw 115
8
Backup and recovery
Creating recovery discs in Windows VIsta
After setting up the computer for the first time, be sure to create a set of recovery discs of the full
factory image. The recovery discs are used to start up (boot) the computer and recover the operating
system and software to factory settings in case of system instability or failure.
Note the following guidelines before creating recovery discs:
●
Use any of the following types of discs: CD-R, DVD+R, DVD+R DL, DVD-R, or DVD-R DL
(purchased separately). The discs you use will depend on the type of optical drive installed in
your computer. Because DVDs store more information than CDs, DVDs and DVDs with doublelayer (DL) support reduce the number of discs required.
NOTE: Read-write discs, such as CD-RW, DVD+RW, and DVD-RW, are not compatible with
the HP Backup & Recovery Manager software.
●
The computer must be connected to AC power during the process.
●
Only one set of the recovery discs can be created per computer.
●
Number each disc before inserting it into the optical drive of the computer.
●
If necessary, you can cancel the disc creation before you have finished creating the recovery
discs. The next time you select Create a set of recovery discs (Recommended), you will be
prompted to continue the disc creation.
To create a set of recovery discs:
1.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
2.
Click Next.
3.
Click Create a set of recovery discs (Recommended), and then click Next.
4.
Follow the on-screen instructions.
116 Chapter 8 Backup and recovery
Backing up your information in Windows Vista
NOTE: You can only recover files that you have previously backed up. HP recommends that you
use HP Backup & Recovery Manager to create an entire drive backup as soon as you set up your
computer.
With HP Backup & Recovery Manager, you can perform the following tasks:
●
Backing up your information regularly to protect your important system files
●
Creating system recovery points that allow you to reverse undesireable changes to your
computer by restoring the computer to an earlier state
●
Scheduling backups at specific intervals or events
When to back up
●
On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
Backup suggestions
●
Create a set of recovery discs using HP Backup & Recovery Manager.
●
Create system recovery points using HP Backup & Recovery Manager, and periodically copy
them to disc.
●
Store personal files in the Documents folder and back up these folders periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your
settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a.
Display the screen.
b.
Copy the screen.
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, and then select Edit > Paste.
NOTE: Before you can perform backup and recovery procedures, the computer must be connected
to external power.
NOTE: Drivers, utilities, and applications installed by HP can be copied to a CD or to a DVD using
HP Backup & Recovery Manager.
Backing up your information in Windows Vista 117
Backing up specific files or folders
You can back up specific files or folders to the recovery partition on the hard drive, to an optional
external hard drive, or to optical discs (CDs or DVDs).
NOTE: This process will take several minutes, depending on the file size and the speed of the
computer.
To back up specific files or folders:
1.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
2.
Click Next.
3.
Click Create or manage backups, and then click Next.
4.
Click Back up user created files and folders, and then click Next.
5.
Follow the on-screen instructions.
Backing up the entire hard drive
When you perform a complete backup of the hard drive, you are saving the full factory image,
including the Windows® operating system, software applications, and all personal files and folders.
NOTE: A copy of the entire hard drive image can be stored on another hard drive, on a network
drive, or on recovery discs that you create.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
To back up your entire hard drive:
1.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
2.
Click Next.
3.
Click Create or manage backups, and then click Next.
4.
Click Create or manage Entire Drive Backups, and then click Next.
5.
Follow the on-screen instructions.
118 Chapter 8 Backup and recovery
Creating recovery points
When you back up modifications since your last backup, you are creating system recovery points.
This allows you to save a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system.
NOTE: The first system recovery point, a snapshot of the entire image, is automatically created the
first time you perform a backup. Subsequent recovery points make copies of changes made after that
time.
HP recommends that you create recovery points at the following times:
●
Before you add or extensively modify software or hardware
●
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier recovery point does not affect data files or e-mails created since
that recovery point.
To create a system recovery point:
1.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
2.
Click Next.
3.
Click Create or manage backups, and then click Next.
4.
Click Create or manage Recovery Points, and then click Next.
5.
Follow the on-screen instructions.
Scheduling backups
Use HP Backup Scheduler to schedule backups for the entire system, for recovery points, or for
specific files and folders. With this tool, you can schedule backups at specific intervals (daily, weekly,
or monthly) or at specific events, such as at system restart or when you dock to an optional docking
station (select models only).
To schedule backups:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup Scheduler.
2.
Follow the on-screen instructions.
Backing up your information in Windows Vista 119
Performing a recovery in Windows Vista
NOTE: You can only recover files that you have previously backed up. HP recommends that you
use HP Backup & Recovery Manager to create an entire drive backup as soon as you set up your
computer.
HP Backup & Recovery Manager helps you with the following tasks for safeguarding your information
and restoring it in case of a system failure:
●
Recovering important files—This feature helps you reinstall important files without performing a
full system recovery.
●
Performing a full system recovery—With HP Backup & Recovery Manager, you can recover your
full factory image if you experience system failure or instability. HP Backup & Recovery Manager
works from a dedicated recovery partition on the hard drive or from recovery discs you create.
Performing a recovery from the recovery discs
To perform a recovery from the recovery discs, follow these steps:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Performing a recovery from the hard drive
There are 2 ways to initiate a recovery from the hard drive:
●
From within Windows
●
From the recovery partition
120 Chapter 8 Backup and recovery
Initiating a recovery in Windows
To initiate a recovery in Windows, follow these steps:
1.
Back up all personal files.
2.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
3.
Click Next.
4.
Click Perform a recovery, and then click Next.
5.
Follow the on-screen instructions.
Initiating a recovery from the hard drive recovery partition
To initiate a recovery from the hard drive recovery partition, follow these steps:
1.
Back up all personal files.
2.
Restart the computer, and then press f11 before the Windows operating system loads.
3.
Click a recovery option, and then click Next.
4.
Follow the on-screen instructions.
Performing a recovery in Windows Vista 121
Creating recovery discs in Windows XP
After setting up the computer for the first time, be sure to create a set of recovery discs of the full
factory image. The recovery discs are used to start up (boot) the computer and recover the operating
system and software to factory settings in case of system instability or failure.
Note the following guidelines before creating recovery discs:
●
Use any of the following types of discs: CD-R, DVD+R, DVD+R DL, DVD-R, or DVD-R DL
(purchased separately). The discs you use will depend on the type of optical drive installed in
your computer. Because DVDs store more information than CDs, DVDs and DVDs with doublelayer (DL) support reduce the number of discs required.
NOTE: Read-write discs, such as CD-RW, DVD+RW, and DVD-RW, are not compatible with
the HP Backup and Recovery Manager software.
●
The computer must be connected to AC power during the process.
●
Only one set of the recovery discs can be created per computer.
●
Number each disc before inserting it into the optical drive of the computer.
●
If necessary, you can cancel the disc creation before you have finished creating the recovery
discs. The next time you select Create factory software recovery CDs or DVDs to recover
the system (Highly recommended), you will be prompted to continue the disc creation.
To create a set of recovery discs:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
2.
Click Next.
3.
Click Create factory software recovery CDs or DVDs to recover the system (Highly
recommended), and then click Next.
4.
Follow the on-screen instructions.
122 Chapter 8 Backup and recovery
Backing up your information in Windows XP
NOTE: You can only recover files that you have previously backed up. HP recommends that you
use HP Backup and Recovery Manager to create an entire drive backup as soon as you set up your
computer.
With HP Backup and Recovery Manager, you can perform the following tasks:
●
Backing up your information regularly to protect your important system files
●
Creating system recovery points that allow you to reverse undesireable changes to your
computer by restoring the computer to an earlier state
●
Scheduling backups at specific intervals or events
When to back up
●
On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
Backup suggestions
●
Create a set of recovery discs using HP Backup and Recovery Manager.
●
Create system recovery points using HP Backup and Recovery Manager, and periodically copy
them to disc.
●
Store personal files in the My Documents folder and back up these folders periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your
settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a.
Display the screen.
b.
Copy the screen.
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, and then select Edit > Paste.
NOTE: Before you can perform backup and recovery procedures, the computer must be connected
to external power.
NOTE: Drivers, utilities, and applications installed by HP can be copied to a CD or to a DVD using
HP Backup and Recovery Manager.
Backing up your information in Windows XP 123
Backing up specific files or folders
You can back up specific files or folders to the recovery partition on the hard drive, to an optional
external hard drive, or to optical discs (CDs or DVDs).
NOTE: This process will take several minutes, depending on the file size and the speed of the
computer.
To back up specific files or folders:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
2.
Click Next.
3.
Click Back up to protect system settings and important data files, and then click Next.
4.
Click Back up individual files and folders, and then click Next.
5.
Follow the on-screen instructions.
Backing up the entire hard drive
When you perform a complete backup of the hard drive, you are saving the full factory image,
including the Windows® operating system, software applications, and all personal files and folders.
NOTE: A copy of the entire hard drive image can be stored on another hard drive, on a network
drive, or on recovery discs that you create.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
To back up your entire hard drive:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
2.
Click Next.
3.
Click Back up to protect system settings and important data files, and then click Next.
4.
Click Back up entire hard drive, and then click Next.
5.
Follow the on-screen instructions.
124 Chapter 8 Backup and recovery
Creating recovery points
When you back up modifications since your last backup, you are creating system recovery points.
This allows you to save a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system.
NOTE: The first system recovery point, a snapshot of the entire image, is automatically created the
first time you perform a backup. Subsequent recovery points make copies of changes made after that
time.
HP recommends that you create recovery points at the following times:
●
Before you add or extensively modify software or hardware
●
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier recovery point does not affect data files or e-mails created since
that recovery point.
To create a system recovery point:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
2.
Click Next.
3.
Click Back up to protect system settings and important data files, and then click Next.
4.
Click Create or manage Recovery Points, and then click Next.
5.
Follow the on-screen instructions.
Scheduling backups
Use HP Backup Scheduler to schedule backups for the entire system, for recovery points, or for
specific files and folders. With this tool, you can schedule backups at specific intervals (daily, weekly,
or monthly) or at specific events, such as at system restart or when you dock to an optional docking
station (select models only).
To schedule backups:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup Scheduler.
2.
Follow the on-screen instructions.
Backing up your information in Windows XP 125
Performing a recovery in Windows XP
NOTE: You can only recover files that you have previously backed up. HP recommends that you
use HP Backup and Recovery Manager to create an entire drive backup as soon as you set up your
computer.
HP Backup and Recovery Manager helps you with the following tasks for safeguarding your
information and restoring it in case of a system failure:
●
Recovering important files—This feature helps you reinstall important files without performing a
full system recovery.
●
Performing a full system recovery—With HP Backup and Recovery Manager, you can recover
your full factory image if you experience system failure or instability. HP Backup and Recovery
Manager works from a dedicated recovery partition on the hard drive or from recovery discs you
create.
Performing a recovery from the recovery discs
To perform a recovery from the recovery discs, follow these steps:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Performing a recovery from the hard drive
There are 2 ways to initiate a recovery from the hard drive:
●
From within Windows
●
From the recovery partition
126 Chapter 8 Backup and recovery
Initiating a recovery in Windows
To initiate a recovery in Windows, follow these steps:
1.
Back up all personal files.
2.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery
Manager.
3.
Click Next.
4.
Click Recover important files or the entire system, and then click Next.
5.
Follow the on-screen instructions.
Performing a recovery in Windows XP 127
Initiating a recovery from the hard drive recovery partition
To initiate a recovery from the hard drive recovery partition, follow these steps:
1.
Back up all personal files.
2.
Restart the computer, and then press f11 before the Windows operating system loads.
3.
Click a recovery option, and then click Next.
4.
Follow the on-screen instructions.
128 Chapter 8 Backup and recovery
9
Connector pin assignments
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
Audio-out (headphone) 129
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
130 Chapter 9 Connector pin assignments
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
RJ-11 (modem) 131
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
Universal Serial Bus
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
132 Chapter 9 Connector pin assignments
10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to
120 volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or
region where the computer is used.
Requirements for all countries and regions
The requirements listed below are applicable to all countries and regions:
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage
rating of 125 or 250 V AC, as required by the power system of each country or region.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320
Standard Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries and regions 133
Requirements for specific countries and regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
Korea
EK
4
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance
coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region
where it will be used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole
grounding type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall
plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
134 Chapter 10 Power cord set requirements
11 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general
household waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the
backlight. Careful handling must be exercised when removing these components. When you remove
these components, handle them carefully.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display
assembly that might require special handling at end-of-life. Disposal of mercury may be regulated
because of environmental considerations. For disposal or recycling information, contact your local
authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must
be disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific
details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary
from one computer model to another.
Battery 135
Perform the following steps to disassemble the display assembly:
1.
Remove all screw covers (1) and screws (2) that secure the display bezel to the display
assembly.
2.
Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of
the display bezel until the bezel disengages from the display assembly.
3.
Remove the display bezel (3).
136 Chapter 11 Recycling
4.
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5.
Remove all screws (1) that secure the display panel assembly to the display enclosure.
6.
Remove the display panel assembly (2) from the display enclosure.
7.
Turn the display panel assembly upside down.
8.
Remove all screws that secure the display panel frame to the display panel.
9.
Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the
display panel frame.
Display 137
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
138 Chapter 11 Recycling
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
17. Remove the backlight frame from the display panel.
Display 139
18. Remove the backlight from the backlight frame.
19. Disconnect the display panel cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
140 Chapter 11 Recycling
Index
A
AC adapter, spare part
numbers 23, 24, 28
antenna, disconnecting 42
audio, product description 4
audio-in jack
location 10
pin assignments 129
audio-out jack
location 10
pin assignments 129
B
backing up 117
backup
files and folders 118, 124
hard drive 118, 124
modifications made to
system 125
modifications made to the
system 119
scheduling 119, 125
base enclosure, spare part
number 17, 27
battery
location 12
removal 37
spare part number 17, 27, 37
battery bay 12
battery latches 12
battery light 11
Bluetooth module
removal 64
spare part
numbers 16, 24, 26, 64
Bluetooth module cable,
illustrated 21
boot options 84
boot order 84
bottom components 12
button components 8
buttons
power 8
TouchPad 7
wireless 8
C
Cable Kit
contents 21
spare part number 19, 21, 28
cables, service considerations 30
caps lock light 8
carrying case, spare part
number 23
chipset, product description 2
CMOS clearing 34
components
bottom 12
buttons 8
front 10
keys 9
left-side 11
lights 8
pointing devices 7
right-side 10
speaker 8
top 7
TouchPad 7
computer feet
locations 36
spare part number 36
Computer Setup
accessing 80
Diagnostics menu 83
File menu 82
navigating and selecting 81
restoring factory settings 81
Security menu 83
System Configuration
menu 84
using 81
computer specifications 86
connectors
power 11
service considerations 30
creating recovery points 119, 125
D
Diagnostics menu 83
discrete base enclosure, spare
part number 17, 28
Disk Sanitizer 83
diskette drive
precautions 30
product description 4
spare part number 23
display assembly
removal 53
spare part numbers 15, 26, 53
display bezel
removal 55
spare part number 15, 27, 56
display component recycling 135
display enclosure, spare part
number 15, 27
display hinge
removal 57
spare part number 15, 27, 57
display inverter
removal 56
spare part number 15, 27, 56
display lid switch module
illustrated 21
removal 52
spare part number 52
display panel, removal 56
display specifications 87
DriveLock password 83
Index 141
drives
boot order 84
preventing damage 30
DVD/CD-RW Combo Drive
precautions 30
removal 45
spare part
number 19, 22, 27, 45
specifications 90
DVD±RW and CD-RW Combo
Drive
precautions 30
removal 45
spare part
numbers 19, 22, 27, 45
specifications 89
E
electrostatic discharge 31
entire hard drive backup 124
esc key 9
Ethernet, product description 4
Execution Disable 84
ExpressCard assembly
spare part numbers 15, 27
ExpressCard slot 11
ExpressCard slot bezel,
illustrated 20
external media cards, product
description 5
external monitor port
location 11
pin assignments 130
F
fan
removal 69
spare part number 15, 24, 69
feet
locations 36
spare part number 36
File menu 82
fn key 9
front components 10
function keys 9
G
graphics, product description
grounding equipment and
methods 33
142 Index
2
H
hard drive
location 12
precautions 30
product description 3
removal 38
spare part
numbers 18, 22, 28, 38
specifications 88
hard drive backup 118, 124
hard drive bay 12
hard drive bay cover
illustrated 20
removal 38
hard drive bracket, removal 39
hard drive recovery 120, 126
hard drive test 83
headphone jack
location 10
pin assignments 129
heat sink
removal 71
spare part numbers 16, 27, 71
hinge
removal 57
spare part number 15, 27, 57
I
I/O address specifications 93
interrupt specifications 92
J
jacks
audio-in 10
audio-out 10
headphone 10
microphone 10
modem 11
network 11
RJ-11 11
RJ-45 11
K
key components 9
keyboard
product description 5
removal 47
spare part numbers 15, 27, 47
keypad keys 9
keys
esc 9
fn 9
function 9
keypad 9
Windows applications 9
Windows logo 9
L
LAN Power Save 84
language, changing in Computer
Setup 84
left-side components 11
legacy support, Universal Serial
Bus (USB) 80, 84
light components 8
lights
battery 11
caps lock 8
optical drive 10
power 9
wireless 8
Logo Kit, spare part
number 23, 27
M
mass storage devices, spare part
numbers 22
memory check 83
memory map specifications 95
memory module
product description 2
removal 43
spare part numbers 18, 24, 43
memory module compartment 12
memory module compartment
cover
illustrated 20
removal 43
microphone jack
location 10
pin assignments 129
model name 1
modem jack
location 11
pin assignments 131
modem module
product description 4
removal 76
spare part
numbers 17, 24, 26, 76
monitor port
location 11
pin assignments 130
N
navigating in Computer Setup
network jack
location 11
pin assignments 132
81
O
operating system, product
description 6
optical drive
location 10
precautions 30
product description 4
removal 45
spare part numbers 19, 22, 45
specifications 89, 90
optical drive light 10
P
packing guidelines 32
panels, product description 2
parallel port mode 84
password clearing 34
passwords 83
pin assignments
audio-in jack 129
audio-out jack 129
external monitor port 130
headphone jack 129
microphone jack 129
modem jack 131
monitor port 130
network jack 132
RJ-11 131
RJ-45 jack 132
Universal Serial Bus (USB)
port 132
plastic parts 29
Plastics Kit
contents 20
spare part number 15, 20, 27
pointing device
components 7
illustrated 7
pointing device components
TouchPad 7
TouchPad buttons 7
TouchPad scroll zone 7
pointing devices, product
description 5
ports
external monitor 11
monitor 11
product description 5
Universal Serial Bus (USB) 11
power button 8
power connector 11
power cord
set requirements 133
spare part numbers 23, 24
power light 9
power requirements, product
description 5
power-on password 83
processor
product description 1
removal 74
spare part
numbers 16, 25, 28, 74
product description
audio 4
chipset 2
diskette drive 4
Ethernet 4
external media cards 5
graphics 2
hard drives 3
keyboard 5
memory module 2
modem module 4
operating system 6
optical drives 4
panels 2
pointing devices 5
ports 5
power requirements 5
processors 1
product name 1
security 6
serviceability 6
wireless 4
product name 1
R
recovery discs
creating 116
using 120, 126
recovery partition 121, 128
recovery points 119, 125
removal/replacement
preliminaries 29
procedures 35
restoring Computer Setup factory
settings 81
right-side components 10
RJ-11 jack
location 11
pin assignments 131
RJ-11 jack cable
illustrated 21
release 67
RJ-45 jack
location 11
pin assignments 132
RTC battery
removal 78
spare part number 17, 26, 78
Rubber Kit, spare part number 27
S
scheduling backups 119, 125
Screw Kit
contents 96
spare part number 23, 27
screw listing 96
SD/MMC Card Reader 10
security cable slot 10
Security menu 83
security, product description 6
selecting in Computer Setup 81
serial number 13, 35
service considerations 29
serviceability, product
description 6
smart card security 83
speaker
location 9
removal 51
spare part number 15, 26, 51
specifications
computer 86
display 87
DVD/CD-RW Combo Drive 90
Index 143
DVD±RW and CD-RW Combo
Drive 89
hard drive 88
I/O addresses 93
interrupts 92
memory map 95
optical drive 89, 90
system DMA 91
startup check 83
static-shielding materials 33
stringent security 83
switch cover
removal 47
spare part number 15, 26, 47
system backup 118, 124
system board
removal 66
spare part numbers 15, 27, 66
System Configuration menu 84
system DMA 91
system fan 84
system information 82
system memory map 95
system recovery points 119, 125
T
Thermal Material Kit, spare part
numbers 16, 24, 25
thermal material,
replacement 72, 73
tools required 29
top components 7
top cover
removal 58
spare part number 15, 26, 58
TouchPad 7
TouchPad board
removal 61
spare part number 15, 26, 61
TouchPad button board
removal 61
spare part number 15, 27, 61
TouchPad buttons 7
TouchPad components 7
TouchPad Miscellaneous Kit,
spare part number 15, 27, 61
TouchPad scroll zone 7
transporting guidelines 32
144 Index
U
Universal Serial Bus (USB) legacy
support 80, 84
unknown password 34
USB port
location 11
pin assignments 132
V
vents 11, 12
W
Windows applications key 9
Windows logo key 9
wireless antenna,
disconnecting 42
wireless button 8
wireless light 8
wireless, product description 4
WLAN module
removal 40
spare part numbers 17, 24, 40
WLAN module compartment 12
WLAN module compartment cover
illustrated 20
removal 42
workstation guidelines 32