RANGE HOODS
INSTALLATION INSTRUCTIONS - USE AND CARE
HB0045
! INTENDED FOR DOMESTIC COOKING ONLY !
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: CLEANING AND OPERATION INFORMATION
ON PAGES 8 to 11.
07020 rev. -
! WARNING
! WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
TO REDUCE THE RISK OF INJURY TO PERSONS
IN THE EVENT OF A RANGE TOP GREASE FIRE,
OBSERVE THE FOLLOWING*:
1.
Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer at the address or telephone number
listed in the warranty.
1.
2.
Before servicing or cleaning unit, switch power off
at service panel and lock service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. IF THE
FLAMES DO NOT GO OUT IMMEDIATELY,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2.
NEVER PICK UP A FLAMING PAN – You may
be burned.
3.
DO NOT USE WATER, including wet dishcloths or
towels – This could cause a violent steam explosion.
4.
Use an extinguisher ONLY if:
A. You own a Class ABC extinguisher and you
know how to operate it.
B. The fire is small and contained in the area where
it started.
C. The fire department has been called.
D. You can fight the fire with your back to an exit.
3.
Installation work and electrical wiring must be
done by qualified personnel in accordance with all
applicable codes and standards, including fire-rated
construction codes and standards.
4.
Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent backdrafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
5.
When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
6.
Ducted fans must always be vented to the outdoors.
7.
Do not use this unit with any solid-state speed
control device.
8.
To reduce the risk of fire, use only metal ductwork.
9.
This unit must be grounded.
*Based on “Kitchen Fire Safety Tips” published by NFPA.
CAUTION
1.
2.
3.
4.
TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
a)
Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low
or medium settings.
b)
Always turn hood ON when cooking at high heat
or when cooking flaming foods.
c)
Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or filter.
d)
Use proper pan size. Always use cookware
appropriate for the size of the surface element.
5.
6.
7.
8.
9.
10.
11.
-2-
For general ventilating use only. Do not use to exhaust
hazardous or explosive materials and vapors.
To avoid motor bearing damage and noisy and/or
unbalanced impeller, keep drywall spray, construction
dust, etc. off power unit.
Your hood motor has a thermal overload which will
automatically shut off the motor if it becomes
overheated. The motor will restart when it will cool
down. If the motor continues to shut off and restart,
have the hood serviced.
The minimum hood distance above cooktop must
not be less than 20” for an electric range, and 24” for
a gas range. A maximum of 30” above cooktop is
highly recommended for best capture of cooking
impurities.
Two installers are recommended because of the
large size and weight of this hood.
To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside – Do not exhaust
air into spaces within walls or ceiling or into attics,
crawl space or garage.
Refer to the specification label on product to see if
this unit is equipped with a thermostat which may start
blower automatically. In this case, to reduce the risk of
injury and to prevent power from being switched on
accidentally, switch power off at service panel and
lock or tag service panel.
Because of the high exhausting capacity of this
hood, you should make sure enough air is entering
the house to replace exhausted air by opening a
window close to or in the kitchen.
Use with approved cord-connection kit only.
Please read specification label on product for
further information and requirements.
All demonstrator range hoods (model numbers ending
by D) are not for sale; these hoods are only for
demonstration purpose.
ABOUT THIS MANUAL
Because of the large amount of models covered by this publication, the illustrations are typical ones. Some details of your unit
may be slightly different of the ones shown.
Please take note this manual uses the following symbols to emphasize particular information:
! WARNING
Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death.
CAUTION
Denotes an instruction which, if not followed, may severely damage the unit and/or its components.
NOTE: Indicates supplementary information needed to fully complete an instruction.
HOOD INSTALLED WITH A CHARCOAL FILTER MODULE
A single blower range hood can be installed either with an exterior outlet or not.
If a single blower range hood is not installed with an exterior outlet, a charcoal filter module must be installed (sold separately).
This module must be installed prior to proceed to the hood installation. Refer to the installation sheet included in the charcoal
filter module kit.
CAUTION
All dual blower range hoods must always be installed with an exterior outlet. Never install a charcoal filter module with
those specific range hoods.
TOOLS NEEDED TO INSTALL THE RANGE HOOD
-
Phillips screwdriver #2 or Robertson #1 and #2
Pair of long nose pliers (to open the horizontal or vertical discharge knockout hole)
Hammer and flat blade screwdriver (to open the electrical knockout hole)
Sheet metal sheers (ducted installation only, for duct adjustment)
Pair of pliers (ducted installation only, for duct adjustment)
Scissors (to cut duct tape)
Pen
Wire stripper
TABLE OF CONTENTS
1. INSTALL DUCTWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. MEASURE THE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. PREPARE THE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4. PREPARE THE HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
5. INSTALL THE ADAPTER/DAMPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6. INSTALL THE HOOD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
7. CONNECT WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
8. REINSTALL BOTTOM PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
9. HALOGEN LIGHT BULBS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
10. CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
11. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
12. SERVICE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
-3-
1. INSTALL DUCTWORK
Plan where and how the ductwork will be installed.
Install proper-sized ductwork, elbow(s) and roof or wall cap for the type of blower you are installing. If using 6’’ (150 mm) round
ducts, use a transition. Use 2’’ (50 mm) duct tape to seal duct joints.
Roof cap
Roof cap
6” round duct
3¼” x 10” duct
3¼” x 10” to 6”
round transition
Wall cap
Wall cap
Hood
Hood
HH0014A
HH0011A
2. MEASURE THE INSTALLATION
Dimensions for the most common installations are shown below.
We recommend to install the hood at a minimum of 20” (508 mm) from an electric range and at 24” (610 mm) from a
gas range.
For optimal performance, the hood should not be installed more than 30” (762 mm) from cooktop.
Cabinets
Cabinets
Hood
Hood
30” maximum
clearance
20” minimum
clearance
(24” for gas)
Standard
36” height
cooktop
Standard
36” height
cooktop
HH0012A
HH0013A
3. PREPARE THE INSTALLATION
Make sure the following items are included:
-Hood
-Filters (2)
-Adapter/damper assembly 31⁄4’’ x 10’’ (for single blower hood models, located inside the hood, under the bottom panel, and for
double blower hood models, temporary assembled on back of the hood)
-Bag of parts including:
(1) wire clamp, (5) 1⁄2’’ double thread screws, (2) wire connectors and (6) 1⁄2’’ screws
Parts sold separately:
! WARNING
In order to prevent the risk of personal injury, do not install a lamp identified for use only in enclosed fixtures.
- Shielded halogen lamps (120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base)
- Transition 31⁄4”x 10” to 6” round (optional, for 6” round ducts installation only)
-4-
3. PREPARE THE INSTALLATION (CONT’D)
NOTE: If the bottom of the cupboard is recessed, attach wood strips (not included), as shown below, in order to properly
install the range hood (A) or charcoal filter unit (B) (if need be) to the cabinet. The wood strips must be as thick as
recess.
B
A
2-3/8”
HO0002
HD0033
Cut-out the openings for duct (A) and power cable (B), in cabinet or wall, according to the direction of discharge chosen.
See figures below.
HORIZONTAL DISCHARGE:
VERTICAL DISCHARGE:
CABINET BOTTOM
C
L
C
L
A
10½”
111 8 ”
A
1¼”
3¾”
3½”
1½”
7 8”
5¼” 5¼”
HD0150A
5¼”
B
1¼” dia.
HD0151A
5¼”
¾”
3 8”
B
4. PREPARE THE HOOD
Remove both filters from the hood. Disassemble the adaptor/damper (A) from the hood.
NOTE: Depending on the hood model, the adapter/damper can be located on back of the hood (for double blower hoods) or
inside the hood (for single blower hoods). In this last case, the bottom panel (B) must be removed to access the
adapter/damper. Refer to figures below.
DOUBLE
BLOWER HOOD:
SINGLE
BLOWER HOOD:
A
A
HO0056
HO0055
B
If it is not done yet, remove the bottom panel from the hood and set aside. Punch out the appropriate electrical knock-out hole.
CAUTION
Never use a hammer and a screwdriver to
punch out the vertical or horizontal
discharge knock-out, because this will
damage the hood internal parts.
HD0152
-5-
4. PREPARE THE HOOD (CONT’D)
Using a long nose pliers, remove the knock-out for the chosen opening (vertical on top or horizontal at the back of the hood).
See figures below.
HORIZONTAL DISCHARGE:
VERTICAL DISCHARGE:
1
2
3
HD0153
5. INSTALL THE ADAPTER/DAMPER
For an horizontal discharge installation only, unfold (if
need be) the foldable flange (C) of the adapter/damper. This
flange must be at 90° from the remaining flanges.
See figure below.
For a vertical discharge installation only, if need be, fold up
the foldable flange (C) of the adapter/damper. This flange
must be at 90° from the adapter/damper sides. Locate this
flange towards the front of the hood. See figure below.
C
C
HO0057
HJ0006
Using (2) 1⁄2” screws, secure the adapter/damper to the top or back of the hood.
Tape the adapter/damper to the hood using duct tape to seal it.
HO0058
NOTE: For the best ventilation performance, if a round duct must be used, the duct diameter must be 6” or more.
Use a 3 1⁄4” x 10” to 6” round transition. The wall duct must be well prepared to receive the adapter. Before performing
the installation, make sure the adapter fits easily in the duct. If this hood replaces another one, please note that location
of the air exhaust can vary from one manufacturer to another.
-6-
6. INSTALL THE HOOD
Run power cable to installation location. Place the hood at its location. Using
a pen, mark the position of the screws (smaller part of the embossed
keyholes). Remove the hood and install (4) 1⁄2” double thread screws at sides
locations (A), leaving a 1⁄8” gap. Place the wire clamp, insert the cable in the
hood and tighten the wire clamp to secure the cable. Place the hood under
the cabinet and slide it in position. Make sure the adapter/damper assembly
enters the ducting and the damper opens freely. Secure the hood by
tightening the screws completely. Install the last 1⁄2” double thread screw (B)
in the remaining embossed hole.
A
B
A
HD0154
7. CONNECT WIRING
! WARNING
Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes
and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to
prevent power to be switched on accidentally.
Connect cable to range hood wiring using included wire connectors.
Connect BLACK to BLACK, WHITE to WHITE and GREEN or BARE WIRE
to GREEN ground screw (1).
1
! WARNING
Do not forget to connect the ground!
HE0059
8. REINSTALL BOTTOM PANEL
Reinstall the bottom panel, using 5 screws for a single blower hood and 6 screws for a double blower hood, as shown below.
SINGLE BLOWER HOOD
DOUBLE BLOWER HOOD
HO0066
HO0059
Then, reinstall filters.
CAUTION
Remove protective plastic film covering filters before reinstalling them (if need be).
-7-
9. HALOGEN LIGHT BULBS
This range hood must use 120 V, 50 W, MR16 with GU10 base or PAR16 with GU10 base, shielded halogen lamps (purchase separately).
! WARNING
In order to prevent the risk of personal injury, do not install a lamp identified for use only in enclosed fixtures.
Install the lamps by placing the bulb leads into their grooves in the
socket and gently push upward and turn clockwise until secured.
HO0060
! WARNING
In order to prevent the risk of personal injury, the halogen lamps must be cooled down before removing them.
To remove lamps, gently push upward and turn counterclockwise to disengage bulb leads from their grooves.
10. CLEANING
! WARNING
Refer to the specification label on the hood to see if this hood is equipped with a thermostat which may start blower
automatically. In this case, to reduce the risk of injury and to prevent power to be switched on accidentally, switch
power off at service panel and lock or tag service panel before cleaning.
The grease filters, bottom panel, intake ring(s) (A) and blower wheel(s) (B)
should be cleaned frequently. Use a warm detergent solution. The grease
filters, intake ring(s) and blower wheel(s) are dishwasher safe.
NOTE: Some minerals, when in contact with dishwasher soap additives,
may cause filters discoloration. This discoloration is not covered by
the warranty.
C
A
To remove a blower wheel, first take off its intake ring. Then remove the
blower wheel by pulling it down smoothly.
NOTE: Do not try to remove the black part (C) attached to the bottom
panel.
B
HD0155
D
When reinstalling the blower wheel(s), make sure the small tab (D) will fit
into one hole of the motor(s).
HD0156
STAINLESS
STEEL CLEANING:
Do:
• Regularly wash surfaces with clean cloth or rag soaked
with warm water and mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after
cleaning. Wipe completely dry.
• You may also use a specialized household stainless steel
cleaner.
Don’t:
• Do not use any steel or stainless steel wool or any other
scrapers to remove stubborn dirt.
• Do not use any harsh or abrasive cleansers.
• Do not allow dirt to accumulate.
• Do not let plaster dust or any other construction residues
reach the hood. During construction or renovation, cover
the hood to make sure no dust adheres to stainless steel
surface.
-8-
10. CLEANING (CONT’D)
STAINLESS STEEL CLEANING (CONT’D):
Avoid: when choosing a detergent
- Any cleaners that contain bleach will attack stainless steel.
- Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.
- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should
never be used close to a range.
ENAMEL FINISH:
Clean with warm water and mild detergent only. If discoloration occurs, use a good enamel polish such as automotive polish.
(DO NOT use rough abrasive cleaner or porcelain cleaner.)
11. OPERATION
Always turn on the hood before begining cooking in order to establish an air flow in the kitchen. Let the blower(s) run for a few
minutes to clear the air after turning off the range.
Following are all the controls used by the hood models covered in this manual. Identify the one installed on your hood and see
how to operate it.
ROCKER SWITCH CONTROL
HC0020
A
B
A. ON/OFF BLOWER AND SPEED CONTROL SWITCH:
This 3-position rocker switch controls the blower speed. Pressing on left side (1) will result in low speed operation, while
pressing on right side (2) will turn on the blower to high speed. To stop the blower operation, set the rocker switch to the
central position (0).
B. ON/OFF LIGHTING INTENSITY CONTROL SWITCH:
This 3-position rocker switch controls the lighting level. According to your needs, press on left side (1) to get nightlight
intensity, or press on right side (2) to obtain full lighting. To shut off the lights, set the rocker switch to the central position (0).
SLIDER SWITCH CONTROL
HC0024
A
B
A. OFF/ON LIGHTING SWITCH:
To turn on the lights, slide this switch to the right (1), and slide to the left (0) to turn them off.
B. ON/OFF BLOWER AND SPEED CONTROL SWITCH:
Slide this switch to the right to turn on the blower. Slide to (1) will result in low speed operation, slide to (2) to reach the
medium speed and slide to (3) to turn the blower to high speed. To stop the blower operation, slide this switch completely
to the left (0).
-9-
11. OPERATION (CONT’D)
MECHANICAL PUSH-BUTTON CONTROL
HC0021
A
B
C
A. OFF BLOWER SWITCH:
Press on this switch to stop the blower operation.
B. SPEED BLOWER SWITCHES:
Press on left switch (1) to turn on the blower on low speed, on middle switch (2) to turn on the blower on medium speed,
and on right switch (3) to turn on the blower on high speed.
C. ON/OFF LIGHTING SWITCH:
Press on this switch to turn on the lights, and press again to turn them off.
OVAL ELECTRONIC CONTROL
HC0022
A
B
C
D
A. DELAY SWITCH:
When a blower speed is selected, press this switch to activate the delay function. The corresponding speed indicator
light will flash to indicate this function is activated. The blower will continue to operate for 5 minutes and will stop
automatically. To cancel the delay function, press the delay switch once again.
B. START/STOP/SPEED SELECTION SWITCHES:
Press the switch corresponding to the desired blower speed. The light over the switch indicates the selected speed (from
1 for low speed to 4 for high speed). To turn off the blower, press once more on the corresponding blower speed switch.
NOTE: When blower is off, pressing on blower speed 1 switch will cause the blower to start on high speed for a very
short lapse of time, and then resume on speed 1.
C. MASTER OFF/FILTER MAINTENANCE/SMARTVENT® (TRIPLE FUNCTION SWITCH):
i. To turn off the blower and the light simultaneously, press the switch once.
ii. After 25 hours of operation, the filter maintenance light indicator will turn itself on. This indicates the filters and the
blower wheel(s) need to be cleaned in order to maintain efficient operation of the unit. The indicator light will stay on
until the function is reset by pressing this switch for 3 seconds.
iii. The light indicator is used for the Smartvent® function as well (NOT AVAILABLE ON ALL HOOD MODELS).
SMARTVENT®: When an excessively high temperature is detected, the detector takes control over the blower and set
it on speed 3; the corresponding light indicator comes on and the indicator of the Smartvent® switch
flashes.
! WARNING
The Smartvent® can start the blower even if the hood is turned off. When this situation occurs, it is impossible to turn
the blower off using the push buttons. If you must stop the blower, do it from the main electrical panel.
The blower will remain on until the heat is back to normal, it then returns to the speed previously selected.
NOTE: In a case of range top grease fire (temperature exceeding 90°C), the Smartvent® will be
deactivated to prevent fire propagation.
D. LIGHT SWITCH:
This switch allows three different lighting levels according to your needs. Press once for nightlight, twice for normal or
three times to obtain full intensity. To shut off the lights without turning off the blower, press once more.
- 10 -
11. OPERATION (CONT’D)
ROUND ELECTRONIC CONTROL
HC0023
A
B
C
D
A. DELAY SWITCH:
When a blower speed is selected, press this switch to activate the delay function. The corresponding blower speed
switch will flash to indicate this function is activated. The blower will continue to operate for 5 minutes and will stop
automatically. To cancel the delay function, press the delay switch once again.
B. START/STOP/SPEED SELECTION SWITCHES:
Press the switch corresponding to the desired blower speed (from 1 for low speed to 4 for high speed). The chosen
switch will light. To turn off the blower, press once more on the corresponding blower speed switch; the switch light will
shut off.
NOTE: When blower is off, pressing on blower speed 1 switch will cause the blower to start on high speed for a very
short lapse of time, and then resume on speed 1.
C. MASTER OFF/FILTER MAINTENANCE/SMARTVENT® (TRIPLE FUNCTION SWITCH):
i. To turn off the blower and the light simultaneously, press this switch once.
ii. After 25 hours of operation, this switch will light to indicate the filters and the blower wheel(s) need to be cleaned in
order to maintain efficient operation of the unit. The switch light will stay on until the function is reset by pressing this
switch for 3 seconds.
iii. The light indicator is used for the Smartvent® function as well.
SMARTVENT®: When an excessively high temperature is detected, the detector takes control over the blower and
set it on speed 3; its switch light comes on and the Smartvent® switch flashes.
! WARNING
The Smartvent® can start the blower even if the hood is turned off. When this situation occurs, it is impossible to turn
the blower off using the push buttons. If you must stop the blower, do it from the main electrical panel.
The blower will remain on until the heat is back to normal, it then returns to the speed previously selected.
NOTE: In a case of range top grease fire (temperature exceeding 90°C), the Smartvent® will be
deactivated to prevent fire propagation.
D. LIGHT SWITCH:
This switch allows three different lighting levels according to your needs. Press once for nightlight, twice for normal or
three times to obtain full intensity. To shut off the lights without turning off the blower, press once more.
- 11 -
12. SERVICE PARTS
SINGLE BLOWER RANGE HOODS
C180, C270, HDN17 AND V10 SERIES
1
2
KEY
No
PART
No.
1
2
4
5
6
*
13296
16153
16150
16151
16152
01988
01757
01989
07020
*
04281
3
3
4
3
DESCRIPTION
ADAPTER/DAMPER
SMOKED GLASS
GLASS HOLDER BLACK (PAIR)
GLASS HOLDER WHITE (PAIR)
GLASS HOLDER GREY (PAIR)
BLOWER WHEEL
INLET RING
ALUMINUM FILTERS (THE PAIR)
INSTALLATION & USER MANUAL
HARDWARE BAG: (1) WIRE CLAMP, (2) WIRE CONNECTORS
(6) #6
X
1/2”
SCREWS,
(5)
QTY PER SERIES
C180 HDN17
C270 V10
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DOUBLE THREAD SCREWS
1
1
* Item not shown
C370, ED370, ROB15, ROB35, ROV15, ROV35 AND V30 SERIES
6
5
KEY
No
PART
No.
1
2
4
5
6
*
13296
16153
16150
16151
16152
01988
01757
14131
07020
*
04281
3
DESCRIPTION
ADAPTER/DAMPER
SMOKED GLASS
GLASS HOLDER BLACK (PAIR)
GLASS HOLDER WHITE (PAIR)
GLASS HOLDER GREY (PAIR)
BLOWER WHEEL
INLET RING
MICROMESH FILTERS (THE PAIR)
INSTALLATION & USER MANUAL
HARDWARE BAG: (2) WIRE CONNECTORS,
(1) WIRE CLAMP, (5) DOUBLE THREAD SCREWS
(6) #6
HL0061
X
1/2”
QTY PER SERIES
C370 ROB15 ROV15
ED370ROB35 ROV35 V30
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
SCREWS
* Item not shown
DOUBLE BLOWER RANGE HOODS
1
2
C600E, ED600E, C600M AND V40E SERIES
3
3
4
4
KEY
No
PART
No.
1
2
6
*
13296
16153
16150
16151
16152
01988
01757
16149
14131
07020
*
04281
3
4
5
DESCRIPTION
ADAPTER/DAMPER
SMOKED GLASS
GLASS HOLDER BLACK (PAIR)
GLASS HOLDER WHITE (PAIR)
GLASS HOLDER GREY (PAIR)
BLOWER WHEEL
INLET RING
DE LUXE MICROMESH FILTERS (THE PAIR)
MICROMESH FILTERS (THE PAIR)
INSTALLATION & USER MANUAL
HARDWARE BAG: (2) WIRE CONNECTORS,
(1) WIRE CLAMP, (5) DOUBLE THREAD SCREWS,
(6) #6
5
5
6
* Item not shown
HL0062
- 12 -
X
1/2”
SCREWS
QTY PER SERIES
C600E
ED600E C600MV40E
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1