Acer EP720 Service manual

SERVICE MANUAL
X1161/X1261/X1161A/X1161N/X110/H5360
Date
Revise Version
Description
2009.05.22
V1.0
Initial Issue
2009.06.25
V2.0
Modify Chapter 5
2009.08.06
V3.0
1. Add X1161’s extended models: X1161A, X1161N,X110
2. Update Engineering Spec. of Chapter 1
3. Modify Chapter 4
2009.09.16
V4.0
1. Add X1261’s extended models: H5360
2. Update Engineering Spec. of Chapter 1
3. Modify Chapter 4
Copyright September, 2009
SI :
TSE:
All Rights Reserved
P/N: 36.8CP01G001
Check:
Approved:
Preface
This manual is applied to X1161/X1261/X1161A/X1161N/X110/H5360 projection system.
The manual gives you a brief description of basic technical information to help in service
and maintain the product.
Your customers will appreciate the quick response time when you immediately identify
problems that occur with our products. We expect your customers will appreciate the
service that you offer them.
This manual is for technicians and people who have an electronic background. Please
send the product back to the distributor for repairing and do not attempt to do anything that
is complex or is not mentioned in the troubleshooting.
Note: The information found in this manual is subject to change without prior notice. Any subsequent changes made to the data herein will be incorporated in future edition.
X1161/X1261/X1161A/X1161N/X110/H5360 Service Manual
Copyright September, 2009
All Rights Reserved
Manual Version 4.0
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
i
X1161/X1161A/X1161N/X110/X1261/H5360 Comparison List
Models
H5360
X1261
X1161
X1161A
X1161N
X110
NAME LABEL
35.8ER02H001
35.8CQ03H001
35.8CP02H001
35.8CP07H001
35.8CP05H001
35.8CP10H001
MAIN BOARD
70.8ER17GR01
70.8CQ09GR01
70.8CP25GR01
70.8CP27GR01
70.8CP29GR01
70.8CP28GR01
DMD CHIP
48.8ER01G001
48.8CQ01G003
48.8EH01G001
IO COVER
70.8ER18GR01
70.8CQ08GR01
70.8CP23GR01
ENGINE
70.8ER15GR01
70.8CQ07GR01
70.8CP22GR01
Parts
SPEAKER
49.8CQ01G001
N/A
LAMP BLOWER
49.8CS01G002
49.8CS01G001
SYSTEM FAN
49.8CP02G002
49.8CP02G001
COLOR WHEEL
70.8ER16GR01
70.8CP21GR01
LAMP
SP.8ER01GC01
SP.8CP01GC01
LVPS
75.8FE01GP01
75.8CP03GP01
LAMP DRIVER
70.8ER20GR01
75.8BA01G002
BOTTOM COVER
70.8ER19GR01
70.8CP26GR01
TOP COVER
75.8ER01G001
75.8CP04H001
FRONT COVER
51.8CP09H021
51.8CP09H001
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
ii
Table of Content
Chapter 1
Introduction
Highlight
1-1
Compatible Mode
1-5
Product Overview
1-9
Chapter 2 Disassembly Process & Assembly Process
Equipment Needed & Product Overview
2-1
Disassemble Lamp Cover Module
2-2
Disassemble Lamp Module
2-2
Disassemble Top Cover Module
2-3
Disassemble Top Shielding
2-3
Disassemble Front Cover and IR Sensor Board
2-4
Disassemble Main Board Module and IO Cover Module
2-5
Disassemble Engine Module
2-7
Disassemble Color Wheel Module
2-8
Disassemble DMD Chip and DMD Board
2-8
Disassemble Zoom Ring
2-9
Disassemble Focus Ring
2-9
Disassemble System Fan Module
2-10
Disassemble Blower
2-11
Disassemble LVPS Module
2-11
Disassemble Lamp Driver Module
2-12
Disassemble Interrupt Switch
2-13
Disassemble Bottom Shielding
2-13
Disassemble Speaker (for X1261/H5360)
2-14
Rod Adjustment
2-14
Re-write System and Lamp Usage Hour
2-15
Assemble Speaker (for X1261/H5360)
2-16
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
iii
Assemble Bottom Shielding
2-17
Assemble Interrupt Switch
2-17
Assemble Lamp Driver Module
2-18
Assemble LVPS Module
2-19
Assemble Blower
2-19
Assemble System Fan Module
2-20
Assemble Focus Ring
2-21
Assemble Zoom Ring
2-21
Assemble DMD Chip and DMD Board
2-22
Assemble Color Wheel Module
2-22
Assemble Engine Module
2-23
Assemble IO Cover and Main Board Module
2-23
Assemble IR Sensor Board and Front Cover
2-25
Assemble Top Shielding
2-26
Assemble Top Cover Module
2-26
Assemble Lamp Module
2-27
Assemble Lamp Cover Module
2-27
Chapter 3 Troubleshooting
LED Lighting Message
3-1
3-2
Main Procedure
Chapter 4 Function Test & Alignment Procedure
Test Equipment Needed
4-1
Service Mode
4-1
OSD Reset
4-1
Test Condition
4-2
Test Inspection Procedure
4-3
PC Mode
4-4
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
iv
Calibration
4-7
Video Performance
4-9
Optical Performance Measure
4-10
Others
4-12
Chapter 5 Firmware Upgrade Equipment Needed
5-1
DLP Composer Lite Setup Procedure
5-2
USB Driver Upgrade Procedure (for X1161 only)
5-4
Firmware Upgrade Procedure
5-5
Waveform Download
5-8
Chapter 6 EDID Upgrade
EDID Introduction
6-1
Equipment Needed
6-2
Setup Procedure (VGA)
6-3
EDID Key-In Procedure
6-4
Un-lock SNID and Default Language Reset 6-6
Appendix A
Exploded Overview
I
Appendix B
Serial Number System Definition I
PCBA Code Definition
II
Appendix C
RS232 function command summary table (for X1261/H5360)I
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
v
Chapter 1
Introduction
1-1 Highlight
No
Item
Description
1
Dimensions (W x H x D)
● 268 mm x 192 mm x 80 mm
2
3
Weight
Tilt Angle
4
Power Supply
5
Keystone correction
6
Cooling system
7
Brightness
● <4.9 lbs
● 2.7 degree with elevator mechanism
● Universal AC 100 – 240 V ~ 50-60 Hz with PFC input
● Variance FAN speed control (Depends on temperature
variant)
● +/ -40 degree (80 degree)
● Advanced Air Flow
● Two fans with system
● Temperature control circuits with adaptive fan rotational
speeds
● Maximum touch temperature follow UL60950-1
● Engineering spec:
• 2250 ANSI Lumens (Typical)
• 2000 ANSI Lumens (Minimum)
● Marketing spec:
• 2500 ANSI Lumens (Standard)
• 2000 ANSI Lumens (ECO)
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
No
Item
8
Contrast
9
Uniformity
10
Throw ratio
11
Audio
12
Projection lens
13
Lamp life
14
System controller
15
Lamp housing
Description
● Engineering spec:
For X1161/X1161N/X1161A/X110:
• 2500: 1 Full White with full power / full Black with eco
power (Minimum; projection lens at tele mode)
• 3600: 1 Full White with full power / full Black with eco
power (Typical; projection lens at tele mode)
For X1261:
• 2100: 1 Full White with full power / full Black with eco
power (Minimum; projection lens at tele mode)
• 3300: 1 Full White with full power / full Black with eco
power (Typical; projection lens at tele mode)
For H5360:
•������������������������������������������������������������
2320: 1 Full White with full power / full Black with eco
power (Minimum; projection lens at tele mode)
• 2900: 1 Full White with full power / full Black with eco
power (Typical; projection lens at tele mode)
● Marketing spec:
• 3500: 1 (for X1161/X1161N/X1161A/X110)
• 3000: 1 (for X1261)
•���������������������
3200: 1 (for H5360)
● Engineering spec:
• 65% JBMA (Minimum; Full power mode)
• 80% JBMA (Typical; Full power mode)
● Marketing spec:
• 85%
● 1.95 – 2.15 distance/width @60” �����������������
(for X1161/X1261/
X1161N/X1161A/X110)
● 1.55 – 1.7 distance/width @60” (for H5360)
● 2W*1 (for X1261 /H5360 only)
● F# 2.41~2.55, f = 21.79~23.99 mm, 1.10X Mechanical Zoom
Lens�������������������������������������
(for X1161/X1261/X1161N/X1161A/X110)
● F# 2.5~2.6, f = 21.86~24 mm, 1.10X Mechanical Zoom Lens
(for H5360)
● 3000 hours, 50% survival rate (Full power Mode)
● 4000 hours, 50% survival rate (Eco power Mode)
● TI DDP2430 ������������������������������������
(for X1161/X1261/X1161N/X1161A/X110)
● TI DDP2431 (for H5360)
● Lamp Assembly could be changed by customer himself, but
should read the user manual for instruction in advance
● Lamp Assembly should be provided by Coretronic and
distributed through authorized agencies
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
No
Item
16
TI DMD
17
Number of active dots
18
Color wheel
19
Lamp
20
Video compatibility
Description
● TI DMD 0.55” 12° 2xLVDS S450 SVGA Digital Mirror Device
(for X1161/X1161N/X1161A/X110)
● TI DMD 0.55” 12° 2xLVDS S450 XGA Digital Mirror Device
(for X1261)
● TI DMD 0.62” 12° S450 720p Digital Mirror Device (for
H5360)
● 800(H) x 600(V) (for X1161/X1161N/X1161A/X110))
● 1024(H) x 768(V) (for X1261)
● 1280(H) x 720(V) (for H5360)
● 6 segments (R81Y41G84C31W52B71) ���������������������
(for X1161/X1261/
X1161N/X1161A/X110)
●6
�������������������������������������������
segments (R90Y35G85C33W42B75)������������
(for H5360)
● 6000 ~ 7650 rpm @ CW 2X and 1.5X (50 ~85Hz)
● 180Watt OSRAM E20.8 open type Lamp ���������������������
(for X1161/X1261/
X1161N/X1161A/X110)
● 200Watt OSRAM E20.8 open type Lamp (for H5360)
● Standards :
• NTSC (3.58/4.43)
• PAL (B/D/G/H/I/M/N)
• SECAM (B/D/G/K/K1/L)
• HDTV (480i,576i 480p, 576p, 720p, 1080i, 1080p)
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
No
21
Item
Terminal
Description
● For X1161/1161A/X110:
• VGA In * 1: One D-Sub 15-Pin Female Connector for PC
input and analog Data ( Component i/p, HDTV, RGB Sync)
• S-video * 1: One Mini DIN 4-Pin connector for S-Video
Input Connector
• Composite * 1: One RCA Jack for Composite Video Input
Connector
• USB * 1: One Type-B USB support F/W up-grade and
reserve remote Page-Up and Page-Down function
● For X1161N:
• VGA In * 1: One D-Sub 15-Pin Female Connector for PC
input and analog Data ( Component i/p, HDTV, RGB Sync)
• USB * 1: One Type-B USB support F/W up-grade and reserve remote Page-Up and Page-Down function
● For X1261:
• VGA In * 1: One D-Sub 15-Pin Female Connector for PC
input and analog Data ( Component i/p, HDTV, RGB Sync)
• S-video * 1: One Mini DIN 4-Pin connector for S-Video
Input Connector
• Composite * 1: One RCA Jack for Composite Video Input
Connector
• VGA out * 1: One D-Sub 15-Pin Female Connector for VGA
output ( Component i/p, HDTV, RGB Sync)
• Audio in * 1: One 3.5mm phone jack for Audio input
• RS232 * 1: One Mini DIN 3-Pin connector for RS232
● For H5360
• VGA In * 1: One D-Sub 15-Pin Female Connector for PC
input and analog Data ( Component i/p, HDTV, RGB Sync)
• S-video * 1:One Mini DIN 4-Pin connector for S-Video
Input
• Composite * 1: One RCA jack for Composite Video Input
• Component * 1: Three RCA jacks for Component Input
• HDMI * 1: Support HDMI v1.3
• Audio in * 1: One 3.5mm phone jack for Audio input
• RS232 * 1: One Mini DIN 3-Pin connector for RS232
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
No
Item
22
Input signal spec.
23
Temperature
24
Maximum Humidity
Description
● Hsync Frequency 30~ 100 kHz
● Vsync Frequency 50~ 85 Hz
● Video Signal RGB (PC)
• Analog RGB 0.7Vp-p, 75 ohm, Separate TTL H,V Sync
• Analog RGB 1Vp-p, 75 ohm, Sync. On Green signal
• Analog RGB 0.7Vp-p, 75 ohm, Composite TTL Sync.
● Video
• Composite video 1Vp-p,75 ohm
• S-video Luminance 0.714Vp-p, 75 ohm
• Chrominance 0.286Vp-p, 75 ohm
• Component Video 1Vp-p, 75 ohm
● Operating:
• for 0 - 2500 ft, 5 - 35 °C
• for 2500 - 5000 ft, 5 - 30 °C
• for 5000 - 10000 ft, 5 - 25 °C
● Storage: -20°C ~ 60°C
● Operating: 5°C ~ 35°C, 80%RH (Max.), Non-condensing
● Storage: -20°C ~ 60°C, 80%RH (Max.), Non-condensing
1-2 Compatible Mode
Compatibility modes (VGA Analog) (for X1161/X1261/X1161N/X1161A/X110)
Compatibility
Resolution
(1) VGA Analog - PC Signal
VGA
SVGA
640 x 480
640 x 480
640 x 480
640 x 480
720 x 400
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
V.Frequency [Hz]
H.Frequency [KHz]
60
72
75
85
70
85
56
60
72
75
85
31.5
37.9
37.5
43.3
31.5
37.9
35.1
37.9
48.1
46.9
53.7
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
Compatibility
XGA
SXGA
QuadVGA
SXGA+
UXGA
Power Mac G4
PowerBook G4
i Mac DV(G3)
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1280 x 960
1400 x 1050
1600 x 1200
640 x 480
800 x 600
1024 x 768
1152 x 870
1280 x 960
640 x 480
640 x 480
800 x 600
1024 x 768
1152 x 870
1280 x 960
1024 x 768
60
70
75
85
70
75
85
60
72
75
85
60
75
60
60
66.6(67)
60
60
75
75
60
66.6(67)
60
60
75
75
75
48.4
56.5
60.0
68.7
63.8
67.5
77.1
64.0
77.0
80.0
91.1
60.0
75.2
65.3
75.00
34.9
37.9
48.4
68.7
75.0
31.4
34.9
37.9
48.4
68.7
75.0
60.0
60
75
85
60
60
60
60
47.8
60.3
68.6
44.8
49.6
59.9
65.3
(2) VGA Analog - Extended Wide timing
1280 x 768
1280 x 768
1280 x 768
WXGA
1280 x 720
1280 x 800
1440 x 900
WSXGA+
1680 x 1050
Horizontal scan rate
Vertical scan rate
Max. pixel rate
30k-100kHz
50-85Hz
170MHz
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
Compatibility modes (VGA Analog) (for H5360)
Compatibility
Resolution
(1) VGA Analog - PC Signal
VGA
SVGA
XGA
SXGA
QuadVGA
SXGA+
UXGA
PowerBook G4
i Mac DV(G3)
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1280 x 960
1400 x 1050
1600 x 1200
640 x 480
640 x 480
800 x 600
1024 x 768
1152 x 870
1280 x 960
1024 x 768
V.Frequency [Hz]
H.Frequency [KHz]
60
72
75
85
120
56
60
72
75
85
120
60
70
75
85
120
70
75
85
60
72
75
85
60
75
60
60
60
66.6(67)
60
60
75
75
75
31.5
37.9
37.5
43.3
61.6
35.2
37.9
48.1
46.9
53.7
77.2
48.4
56.5
60.0
68.7
98.8
63.8
67.5
77.1
64.0
77.9
80.0
91.1
60.0
75.0
65.3
75.00
31.5
35
37.88
48.4
68.7
75.2
60.0
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
Compatibility
Resolution
(2) VGA Analog - Extended Wide timing
1280 x 768
1280 x 768
1280 x 768
WXGA
1280 x 720
1280 x 800
1366 x 768
WXGA+
1440 x 900
WSXGA+
1440 x 900
Horizontal scan rate
Vertical scan rate
Max. pixel rate
V.Frequency [Hz]
H.Frequency [KHz]
60
75
85
60
60
60
60
60
47.8
60.3
68.6
44.8
49.6
47.71
55.9
65.3
30k-100kHz
50-85Hz
170MHz
Note: If the Compatibility modes supportive signal is different from User's Manual, please refer to User’s Manual.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
1-3 Product Overview
Projector Outlook
Front /Upper side
Item
Description
Item
Description
1
Ventilation (inlet)
6
Lens cap
2
Ventilation (outlet)
7
Power button
3
Remote control receivers
8
Remote control
4
Focus ring
9
Zoom lever
5
Zoom lens
10
Horn
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-
Rear side (for X1161/X1261/X1161A/X1161N/X110)
Item
Description
Item
Description
1
Power socket
Below items are for X1261 only:
2
KensingtonTM lock port
4
S-Video input connector
3
PC analog signal/HDTV/component video
input connector (VGA IN 1 or VGA IN)
5
Composite video input connector
Below items are for X1161/X1161A/X110
only:
6*
PC analog signal/HDTV/component
video input connector (VGA IN 2)
4
S-Video input connector
7
RS232 connector
5
Composite video input connector
10 USB connector
7* RS232 connector
Below item is for X1161N:
10 USB connector
Monitor loop-through output
connector (VGA-Out)
9 Audio input connector
10* USB connector
8
Note: “*” for optional connector port.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-10
Rear side (for H5360)
Item
Description
Item
Description
1
Power socket
6
YPbPr input connector
2
KensingtonTM lock port
7
S-Video input connector
3
RS232 connector
8
Composite video input connector
4
PC analog signal/HDTV/component video
input connector (VGA IN 1 or VGA IN)
9
Audio input connector
5
HDMI connector
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-11
Remote Control and Control Panel Layout
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-12
Item
1
2
Icon
Function
Remote control
receiver
POWER
3
MENU
4
5
KeyPad 0~9
KeyPad 0~9
6
RESYNC
7
FREEZE
8
KEYSTONE
10
11
Four directional
select keys
ZOOM
SOURCE
12
HIDE
13
Empowering
key
9
Description
Receives signals from remote control.
Refer to the “Turning the Projector On/Off” section.
• Press “MENU” to launch the Onscreen display
(OSD) menu, back to the previous step for the
OSD menu operation or exit the OSD menu.
• Confirm your selection of items.
Press “0~9” to input a password in the “Security”.
To choose the desired aspect ratio (Auto/4:3/16:9).
Automatically synchronizes the projector to the
input source.
To pause the screen image.
Adjusts the image to compensate for distortion
caused by tilting the projector (± 40 degrees).
Use up, down, left, right buttons to select items or
make adjustments to your selection.
Zooms the projector display in or out.
Changes the active source.
Momentarily turns off the video. Press “HIDE” to
hide the image, press again to display the image.
Unique Acer functions: eView, eTimer, ePower
Management.
Note:
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-13
Getting Started
Connecting the Projector
Item
Description
Item
Description
1
Power cord
6
S-Video cable
2
VGA cable
7
Audio cable jack/jack
3
Composite video cable
8
Audio cable jack/RCA
4
RS232 cable
9
USB cable
Note: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-14
System Block Diagram (for X1161/X1161A/X110)
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-15
System Block Diagram (for X1261)
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-16
System Block Diagram (for H5360)
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-17
Bottom Cover Dimension
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
1-18
Chapter 2
Disassembly & Assembly Process
2-1 Equipment Needed & Product Overview
1. Screw Bit (+): 105
2. Screw Bit (+): 107
3. Screw Bit (-): 107
4. Hex Sleeves 5mm
5. Long Nose Nipper
6. Tweezers
7. Projector
* Before you start: This process is protective level II. Operators should wear electrostatic chains.
* Note: - If you need to replace the Main Board, you have to get into Service Mode and record the lamp usage hour, please refer to section 2-21.
- As the process of X1161/ X1161A/X1161N/X110/H5360 disassembling is the same as X1261, we take X1261 for example here.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
2-2 Disassemble Lamp
Cover Module
1. Loosen 2 screws (as red circle) on the
Lamp Cover.
2. Disassemble the Lamp Cover Module.
2-3 Disassemble Lamp
Module
1. Loosen 2 screws (as red circle) on the
Lamp Module.
2. Take off the Lamp Module.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
2-4 Disassemble Top Cover
Module
1. Unscrew 2 screws (as red circle) from the
Bottom Cover.
2. Remove the Top Cover Module.
Note: - When you remove the Top Cover, take care the 6 tenons (as green square).
2-5 Disassemble Top
Shielding
1. Unscrew 5 screws (as red circle) to disassemble the Top Shielding.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
2-6 Disassemble Front
Cover and IR Sensor
Board
1. Unplug 1 connector (as yellow square).
2. Press two sides (as red arrows point) to unfasten 2 tenons (as green square).
3. Remove the Front Cover.
4. Tear off the mylar (as blue square).
5. Unscrew 2 screws (as red circle).
6. Remove the IR Sensor Board and IR Cap.
IR Sensor Board
IR Cap
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
2-7 Disassemble Main Board
Module and IO Cover
Module
1. Tear off 3M tape (as green square).
2. Unplug 6 connectors (as yellow square).
3. Unscrew 2 screws (as red circle).
Please refer to the table as below for
details of each connector.
F
Item
Male Connector
on Main Board
E
D
The key feature
A
Lamp Driver
Black wire tube (5 pin)
B
System Fan
Compose of Red/Yellow/Black
Wire (3 pin)
C
Blower
Compose of Red/Black/White
Wire (3 pin)
C
B
A
Figure
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
Male Connector
on Main Board
Item
The key feature
D
Photo Sensor
Compose of Red/Black/White
Wire and Black wire tube (3 pin)
E
IR
Compose of Red/Black/Whit
Wire and Black wire tube (3 pin)
F
Speaker
(for X1261/H5360)
Compose of Red/Black Wire and
Black wire tube (2 pin)
Figure
4. Unplug 1 connector (as blue square).
5. Disassemble the Main Board Moudle.
6. Unscrew 2 screws (as green circle).
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
7. Unscrew 4 hex screws (as blue circle).
8. Separate the Main Board and IO Cover Module.
IO Cover
NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal.
2-8 Disassemble Engine
Module
1. Tear off EMI Gasket (as green square).
2. Unscrew 4 screws (as yellow circle) to disassemble the Engine Module.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
2-9 Disassemble Color
Wheel Module
1. Unscrew 2 screws (as red circle) to disassemble the Color Wheel Module.
2. Unscrew 1 screw (as blue circle) to disassemble the Photo Sensor Board from the Color Wheel Module.
Note: - Avoid touching the glass parts of Color Wheel.
2-10 Disassemble DMD Chip and DMD Board
1. Unscrew 2 screws (as red circle) to disassemble the Heat Sink and DMD Module.
2. Rotate the screw (as yellow circle)
180° counterclockwise to disassemble
the DMD Board and DMD Chip.
Note: - Avoid touching the DMD Chip when you disassemble it.
- Pay attention to the fixed position when assembling the DMD Chip.
NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
2-11 Disassemble Zoom Ring
1. Unscrew 2 screws (as red circle) to disassemble the Zoom Ring and Zoom Ring Fixed Holder.
Zoom Ring
2-12 Disassemble Focus Ring
1. Unscrew 3 screws (as red circle) to disassemble the Focus Ring.
Zoom Ring Fixed Holder
Focus Ring
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-
2-13 Disassemble System Fan Module
1. Unscrew 3 screws (as red circle) to disassemble the Fan Module.
2. Tear off the EMI tape (as green square).
3. Disassemble the System Fan Module.
4. Unscrew 4 screws (as blue circle) to separate System Fan and Fan Shielding.
Note: - Take the Fan Module as the right gesture.
System Fan
the right gesture
Fan Shielding
the wrong gesture
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-10
2-14 Disassemble Blower
1. Unscrew 3 screws (as red circle).
2. Disassemble the Blower.
2-15 Disassemble LVPS Module
1. Unplug 2 connectors (as yellow square).
2. Unscrew 6 screws (as red circle).
3. Disassemble the LVPS Module and the AC Inlet Bracket.
4. Unplug 1 connector (as green square).
NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle as above image shows. Please detach the Circuit boards and follow local regulations for disposal.
AC Inlet Bracket
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-11
2-16 Disassemble Lamp Driver Module
1. Unscrew 1 screw (as red circle) to disassemble the Lamp Driver Module.
2. Unscrew 2 screws (as blue circle).
3. Unplug 3 connectors (as green square) to disassemble the cables from Lamp Driver Module.
4. Unscrew 4 screws (as yellow circle) to disassemble the Lamp Driver Module and Lamp Driver Holder. NOTE: Circuit boards > 10 cm² has been highlighted with the yellow rectangle
as above image shows. Please detach the Circuit boards and follow local regulations for disposal.
Lamp Driver to Lamp Cable
Lamp Driver Holder
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-12
2-17 Disassemble Interrupt Switch 1. Unfasten 2 tenons (as green square) to disassemble the Interrupt Switch.
Interrupt Switch
2-18 Disassemble Bottom Shielding
1. Tear off the EMI tapes (as yellow square).
1. Unscrew 2 screws (as red cricle) to disassemble the Bottom Shielding.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-13
2-19 Disassemble Speaker (for X1261/H5360)
1. Unfasten 2 tenons (as green square)
as blue arrows point to disassemble the
Speaker.
2-20 Rod Adjustment
1. Environment Adjustment
- The distance between the engine and
the screen is 2.38 M.
- This process should be done at a dark
environment (under 2 Lux).
2. Procedure Adjustment
- Change
the screen to "white screen".
- Adjust the screws by using the rod
on the engine module to readjust the
image.
("Screw 1" should be adjusted first, and then "screw 2". Adjust until the yellowish
or bluish parts disappeared.)
2
1
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-14
3. Abnormal image inspection
- It should not have any abnormal color
at the frame of the image by estimating
through the eyes.
Note: - To avoid over adjusting the rod.
- After the opreation, please use the glue
to fix the screws.
2-21 Re-write System and
Lamp Usage Hour
1. Get into Service Mode
- Press "Power", "Left", "Left" and "Menu" buttons sequentially to get into Service Mode.
2. Get into Other Settings Mode
- Use "Up" or "Down" buttons to select "Other Settings", then press "Menu" button.
3. Re-write System Hours
- Select "System Hours Adjust" and use "Left" or "Right" buttons to re-write the "System Hours (full)".
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-15
4. Re-write Lamp Hours (Full power mode)
- Select "Lamp Hours Adjust" and use "Left" or "Right" buttons to re-write the "Lamp Hours (full)".
5. Re-write Lamp Hours (ECO mode)
- Select "Lamp Hours" and use "Left" or "Right" buttons to re-write the "Lamp Hours (low)".
6. Exit Service Mode
- Use "Up" or "Down" buttons to select "Exit", press "Menu" button to exit the Service Mode.
Note: left key = decrease System/Lamp hour
right key =increase System/Lamp hour
2-22 Assemble Speaker
(for X1261/H5360)
1. Fasten 2 tenons (as green square) as blue arrows point to assemble the Speaker.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-16
2-23 Assemble Bottom Shielding
1. Screw 2 screws (as red circle) to
assemble the Bottom Shielding.
2. Stick the EMI tapes (as yellow square).
2-24 Assemble Interrupt Switch
1. Fasten 2 tenons (as green square) to assemble the Interrupt Switch.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-17
2-25 Assemble Lamp Driver Module
1. Screw 4 screw (as yellow circle) to assemble the Lamp Driver Module and Lamp Driver Holder.
2. Plug 3 connectors (as green square) to assemble the cables on Lamp Driver Module.
3. Screw 2 screws (as blue circle).
4. Screw 1 screw (as red circle) to assemble the Lamp Driver Module.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-18
2-26 Assemble LVPS Module
1. Plug 1 connector (as green square).
2. Assemble the LVPS Module and the AC Inlet Bracket.
3. Screw 6 screws (as red circle).
4. Plug 2 connectors (as yellow square).
2-27 Assemble Blower
1. Assemble the Blower.
2. Screw 3 screws (as red circle).
.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-19
2-28 Assemble System Fan Module
1. Screw 4 screws (as blue circle) to assemble System Fan and Fan Shielding.
2. Assemble the System Fan Module.
3. Stick the EMI tape (as green square).
4. Screw 3 screws (as red circle) to assemble the Fan Module.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-20
2-29 Assemble Focus Ring
1. Screw 3 screws (as red circle) to assemble the Focus Ring.
2-30 Assemble Zoom Ring
1. Screw 2 screws (as red circle) to assemble the Zoom Ring and Zoom Ring Fixed Holder.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-21
2-31 Assemble DMD Chip and DMD Board
1. Rotate the screw (as yellow circle) 180° clockwise to assemble the DMD Board and DMD Chip.
2. Screw 2 screws (as red circle) to assemble the Heat Sink and DMD Module.
Note: - Avoid touching the DMD Chip.
- Pay attention the fixed position when assembling the DMD Chip.
2-32 Assemble Color Wheel Module
1. Screw 1 screw (as blue circle) to assemble the Photo Sensor Board on the Color Wheel Module.
2. Screw 2 screws (as red circle) to assemble the Color Wheel Module on Engine Module.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-22
2-33 Assemble Engine Module
1. Screw 4 screws (as yellow circle) to assemble the Engine Module.
2. Stick the EMI Gasket (as green square).
2-34 Assemble IO Cover and Main Board Module
1. Assemble the IO Cover and Main Board Module.
2. Screw 4 hex screws (as blue circle).
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-23
3. Screw 2 screws (as green circle).
4. Assemble the Main Board Module.
5. Plug 1 connector (as blue square).
6. Screw 2 screws (as red circle).
7. Plug 6 connectors (as yellow square).
8. Stick 3M tape (as green square) on the Main Boad Module.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-24
2-35 Assemble IR Sensor Board and Front Cover
1. Assemble the IR Sensor Board and IR Cap.
2. Screw 2 screws (as red circle).
3. Stick the mylar (as blue square).
4. Assemble the Front Cover.
5. Press two sides (as red arrows point) to fasten 2 tenons (as green circle).
6. Plug 1 connector (as yellow square).
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-25
2-36 Assemble Top Shielding
1. Screw 5 screws (as red circle) to assemble the Top Shielding.
Note: Avoid pressuring the Speaker cable (as yellow square) when you assemble the Top shielding. (for X1261/H5360)
2-37 Assemble Top Cover Moudle
1. Assemble the Top Cover Module.
Note: Take care the 6 tenons (as green square) when you assemble the Top Cover.
2. Screw 2 screws (as red circle) on the Bottom Cover.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-26
2-38 Assemble Lamp Moudle
1. Assemble the Lamp Module.
2. Tighten 2 screws (as red circle) on the Lamp Module.
2-39 Assemble Lamp Cover Module
1. Assemble the Lamp Cover Module.
2. Tighten 2 screws (as red circle) on the Lamp Cover.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
2-27
Chapter 3
Troubleshooting
3-1 LED Lighting Message
Message
Power LED
Red
Blue
Flash ON to OFF 100ms
--
Standby
V
--
Power button ON
--
V
Lamp retry
--
Input Power Plug
Power off
(Cooling state)
Power button OFF:
Cooling completed;
Standby Mode
0.5 second H(ON),
0.5 second L(OFF) flashing
V
0.5 second H(On),
0.5 second L(Off) flashing
--
--
Error (Thermal
Failure)
0.5 second H(On), 0.5 second L(Off) flashing red twice, and blue
LED ON 2 second, and by returns
Error (Fan lock)
0.5 second H(On), 0.5 second L(Off) flashing red twice, and blue
LED ON 2 second, and by returns
Error (Lamp breakdown)
0.5 second H(On), 0.5 second L(Off) flashing blue twice, and red
LED ON 2 second, and by returns
Error (Color Wheel
Failure)
0.5 second H(On), 0.5 second L(Off) flashing blue twice, and red
LED ON 2 second, and by returns
Note: Steady Light: "V"
No Light: "--"
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
3-
3-2 Main Procedure
No
Symptom
Procedure
- Ensure the Power Cord and AC Power Outlet are securely
connected
1
No Power
- Ensure all connectors are securely connected and aren’t
broken
- Check LVPS
- Check Lamp Driver
- Check Main Board
- Check LED Status
a. Thermal/Fan Failure: Quick Flashing red twice and
Steady blue by returns
- Check Fan
- Check Main Board
2
Auto Shut Down
b. Lamp/Color wheel ����������������������������������������
Failure���������������������������������
: Quick Flashing blue twice and
Steady red by returns
- Check Lamp
- Check Lamp Driver
- Check Color Wheel
- Check Photo Sensor
- Check Main Board
- Ensure all connectors are securely connected and aren’t
broken
- Check Lamp Cover, Interrupt Switch
- Check Lamp Module
3
No Light On
- Check Lamp Driver
- Check LVPS
- Check Main Board
- Check Color Wheel
- Check Photo Sensor Board
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
3-
No
Symptom
Procedure
- Ensure the Signal Cable and Source work
(If you connect multiple sources at the same time, use the
"Source" button switch)
- Ensure all connectors are securely connected and aren’t
broken
4
No Image
- Check Main Board
- Check DMD Board
- Check DMD Chip
- Check Color Wheel
- Check Engine Module
5
Mechanical Noise
- Check Color Wheel
- Check Fan Module
- Check if the Main Board and the DMD Board are
assembled properly
6
Line Bar/Line Defect
- Check Main Board
- Check DMD Board
- Check DMD Chip
- Do "Reset (All data)" of the OSD Menu
- Ensure that the signal cables and source are work as well
- Check Lamp Driver and waveform
7
Image Flicker
- Check Lamp Module
- Check Color Wheel
- Check Photo Sensor and clean Photo Sensor
- Check DMD Board
- Check Main Board
- Do "Reset (All data)" of the OSD Menu
- Adjust Color Wheel Index
8
Color Abnormal
- Check Main Board
- Check DMD Board
- Check Color Wheel
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
3-
No
Symptom
Procedure
- Ensure the projection screen without dirt
- Ensure the projection lens is clean
9
Poor Uniformity/
Shadow
- Ensure the Brightness is within spec
- Check rod alignment
- Check Engine Module
- Ensure the projection screen without dirt
- Ensure the projection lens is clean
10
Dead Pixel/Dust
(Out of spec.)
- Clean DMD Chip and Engine Module
- Check DMD Chip
- Check Engine Module
- Ensure that the signal cables and source work as well
11
Garbage Image
- Check Main Board
- Check DMD Board
- Remote Controller
a. Check Battery
12
Remote Controller
Failed
b. Check Remote Controller
c. Check IR Sensor Board
d. Check Main Board
13
Function Abnormal
- Do "Reset (All data)" of the OSD Menu
- Check Main Board
- Ensure that the signal cables and source are work as well
14
Audio Abnormal
(X1261/H5360 only)
- Ensure that your Projector is not in “Mute” mode
- Check Main Board
- Check Speaker
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
3-
No
Symptom
Procedure
- An unique Universal Password which is printed on the
Security Card. This unique password is a back door of
Administrator Password which will be accepted by projector
anytime no matter what the Administrator Password is.
- If you forget the Password, please do the following steps to get
the Universal Password:
(1) Click the "AcerSNID"
(2) Input SNID number. (SNID number is on the Security Card)
15
Forgetting Password
(administrator
Password)
(3) Click "Calculate". Then the Universal Password will appear.
16
Universal Password
Failure
- Please confirm whether the SNID number of Service Mode
is the same as the SNID number on the backside of projector?
- If not, please do the actions as below:
a. Execute the EDID Upgrade Procedure (refer to Chapter 6)
b. Execute "Un-lock SNID and Default Language Reset" (refer
to 6-5 of Chapter 6)
c. Press "Power", "Left", "Left" and "Menu" buttons sequentially
on remote controller to get into Service Mode to obtain the
SNID number, then calculate the Universal Password.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
3-
Chapter 4
Function Test & Alignment Procedure
4-1 Test Equipment Needed
- IBM PC with SVGA/XGA resolution
- DVD player with Multi-system, equipped "Component", "S-Video","Composite" and
"HDMI".
- HDTV Source (480P, 720P, 1080i, 1080P)
- Minolta CL-100
- Quantum Data 802B or CHROMA2327 (Color Video Signal & Pattern Generator)
4-2 Service Mode
1. Turn on the projector
2. Do the following actions sequentially to get into Service Mode
(1) Press "Power", "Left", "Left" and "Menu" buttons sequentially on remote controller.
(2) Service Mode will be shown.
(3) Choose "Exit" to leave the Service Mode after confirming the configuration.
4-3 OSD Reset
1. After final QC step, we have to erase all saved change again and restore the OSD
default setting. The following actions will allow you to erase all end-users' settings and
restore the default setting:
(1) Please get into OSD menu.
(2) To execute "Reset" function.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
4-4 Test Condition
- Circumstance brightness: Dark room less than 2.0 lux.
- Inspection distance: 1.8 m~2.5 m functional inspection.
- Screen size: 60 inches diagonal.
- After repairing each unit, it should be Run-in (refer to the below table).
Symptom
Normal repair
NFF
Auto shutdown
Run-in Time
2 hours
4 hours
6 hours
- Get into Burn-In Mode
* Cycle setting is based on the defect symptoms. ie: If it is NFF, the run-in time is 4 hours. You have
to set the lamp on for 50 min. and lamp off for 10 min for 4 cycles.
Press power→ left → left → menu on remote controller
Choose Burn In > enter
Lamp On (Min)
Press right key to adjust the time (50)
Lamp Off (Min)
Press right key to adjust the time (10)
Set Burning cycle
Press right key to adjust the cycle
After setting up the time, choose ''Enter into Burn In Mode'' and press "Menu" button.
Screen Defects (While replacing DMD Chip, DMD Board, Main Board)
Frame
< Figure: Zone A, Zone B, Zone C & Frame (as green line) Definition, Active area=Zone A + Zone B >
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
Defect specification table
Order
1
Symptom
Bright pixel (dots)
Pattern
Gray 10 pattern
Criteria
A+B≤ 1
2
Dark pixel (dots)
White pattern
A+B ≤ 6
3
Bright blemish
Gray 15 pattern
A+B ≤ 10
4
Dark blemish
Blue 60 pattern
A+B ­­≤ 10
5
Bright dot on frame
Gray 10 pattern
≤1
6
Unstable pixel
White & Black pattern
A+B ≤ 1
7
Adjacent dark pixel
White & Black pattern
A+B = 0
4-5 Test Inspection Procedure
Change parts
Update
Main
Board
Firmware
Version Update
v
v
Color Wheel Index
v
PC Calibration
v
v
Video Calibration
v
v
G Sensor Calibration
v
v
Reset Lamp Hour
v
OSD Reset
v
EDID
v
Re-write Lamp
Hour Usage
v
Reset Default
Language
v
Color
Wheel
Lamp
Module
Engine
Module
EDID
Lamp
Driver
v
v
v
v
v
v
Rod adjustment
v
Waveform Download
v
Note: - If Color appears abnormal after changing Main Board Module, please do Color Wheel index adjustment.
- After changing parts, check the information above table.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
4-6 PC MODE
Note: - When getting into function test, adjust the zoom ring and focus ring to guarantee the image maximum and clearest, then start to test.
- Test signal: analog 800 x 600 @60Hz (for X1161);
analog 1024 x 768 @60Hz (for X1261);
analog 1280 x 720 @60Hz (for H5360).
- We take X1261 for example here.
1. Frequency and tracking boundary
Procedure
- Test equipment: video generator
- Test signal: analog 1024 x 768 @60Hz
- Test pattern: general-1 or master
- Check and see if the image sharpness is well
performed.
- If not, re-adjust by the following steps:
(1) S
elect "Frequency" function to adjust the total
pixel number of pixel clock in one line period.
(2) S
elect "Tracking" function and use right or left
arrow key to adjust the value to minimize video
flicker.
- Adjust Resync or Frequency/Tracking/H Image
Shift/V Image Shift to the inner screen.
Inspection item
- Eliminate visual wavy noise by Rsync, Frequency or Tracking selection.
- Check if there is noise on the screen.
- Horizontal and vertical position of the video should
be adjustable to the screen frame.
Criteria
- If there is noise on the screen, the product is
considered as failure product.
- If there is noise on the screen, use auto or manual
“frequency” function or “tracking” function to adjust
the screen.
- The PC mode functionally sure be workable
include support format with frequency and auto
detected functional will be workable.
General-1
Master
2. Bright Pixel
Procedure - Test equipment: video generator
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
- Test signal: 1024 x 768 @60Hz
- Test Pattern: Gray 10
Inspection item
- Bright pixel check
Criteria
- ����������������������������������������������
Bright pixel should be no more than 1 under gray 10 pattern.
- Adjacent pixels are unacceptable.
- Ref. Defect specification table
Gray 10
3. Dark Pixel
Procedure - Test equipment: video generator
- Test signal: 1024 x 768 @60Hz
- Test Pattern: Full white
Inspection item
- Dark pixels check
Criteria
- The dark pixel should be no more than 6 under full white pattern.
- Adjacent pixels are unacceptable.
- Ref. Defect specification table
Full white
4. Bright Blemish
Procedure
- Test equipment: video generator
- Test signal: 1024 x 768 @60Hz
- Test Pattern: Gray 15
Inspection item
- Bright blemish check
Criteria
- The bright blemish should be no more than 10 under gray 15 pattern.
- Ref. Defect specification table
Gray 15
5. Dark Blemish
Procedure
- Test equipment: video generator
- Test signal: 1024 x 768 @60Hz
- Test Pattern: Blue 60
Inspection item
- Dark blemish check
Criteria
- The dark blemish should be no more than 10 under blue 60 pattern.
Blue 60
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
- Ref. Defect specification table
6. Focus test
Procedure - Test equipment: video generator
- Test signal: analog 1024 x 768 @60Hz
- Test pattern: Full screen
Inspection item
- Focus check
Criteria
-From screen 2.38 M via visual to check the focus,
look at the entire screen, focus shall be clear,
crisp, and sharp over the entire surface of the display pattern. (Blur word on one of the corner after
adjustment is acceptable. However, the word
should at least be recognizable.)
Full screen
7. Color performance
Procedure - Test equipment: video generator.
- Test signal: 480p, 720p, 1080i
- Test pattern: Master, 64 gray RGBW or SMPTEbar
* Please refer to 4-2 to get into service mode. Use
720p & 1080p signal, master pattern to do HDTV
test. Color cannot discolor to purple and blue.
Inspection item
- Check if each color level is well-functioned.
- Color saturation
Criteria
- Screen appears normal. It should not have any
abnormal condition, such as lines appear on the
screen and so on.
- Color appears normal.
- It is unacceptable to have few lines flashing.
- RGBW should all appear normal on the screen
and sort from R -G-B-W.
- Color levels should be sufficient and normal. (The
unidentified color levels on both left and right
sides should not over 8 color levels.)
- Gray level should not have abnormal color or
heavy lines.
- If color appears abnormal, please get into service mode to do Color Wheel Index adjustment.
- The PC mode functionally sure be workable
Master
64 gray RGBW
SMPTEbar
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
include support format with frequency and auto
detected functional will be workable.
4-7 Calibration
1. PC Calibration
Procedure
- Test equipment: video generator
- Once Main Board is changed. PC Calibration should be done as well.
(1) Test signal analog: 1024 x 768 @60Hz
(2) Test Pattern: White (up) Black (down)
White/Black
- Note
(1) Calibration pattern should be in full screen mode.
(2) Please press "Power", "Left", "Left" and "Menu" buttons sequentially to get into Service Mode.
(3) Choose "Analog Settings", press "Menu" button to access "PC Calibration" for correction in
Service Mode. Choose "Exit" to leave the Service Mode.
Check pattern
- Test signal: 1024 x 768 @60Hz
- Test pattern: In focus II or 64 gray RGBW
* After finishing ADC adjustment, check 64 gray RGBW pattern.
Inspection item
- Color saturation
Criteria
- There should not have any lack of RGBW. The color should appear normal and sort in right order.
- Color levels should be sufficient and normal. (the unidentified color levels on both left and right sides should not over 8 color levels.)
InFocus II
/ 64 gray RGBW
2. Video Calibration
Procedure
- Test equipment: video generator
- Once Main Board is changed. Video Calibration should be done as well.
(1) Test signal: 480i
(2) Test Pattern: SMPTEbar
- Note
SMPTEbar
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
(1) Calibration pattern should be in full screen mode.
(2) Please press "Power", "Left", "Left" and "Menu" buttons sequentially to get into Service Mode.
(3) Choose "Analog Settings", press “Menu” button to access "Video Calibration for" correction in
Service Mode. Choose “Exit” to leave the Service Mode.
Check pattern
- Test signal: 480i
- Test pattern: In focus II or 64 grey RGBW
* After finishing ADC adjustment, check 64 gray RGBW pattern.
Inspection item
- Color saturation
Criteria
- There should not have any lack of RGBW. The color should appear normal and sort in right order.
- Color levels should be sufficient and normal. (the unidentified color levels on both left and right sides should not over 8 color levels.)
InFocus II
/ 64 gray RGBW
3. G Sensor Calibration
- Please put the Projector on a horizontal surface.
- Please press "Power", "Left", "Left" and "Menu" buttons sequentially to get into Service Mode.
- Choose and access "G Sensor Calibration" for correction.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
4-8 Video Performance
1. CVBS
Procedure - Test equipment: DVD player
- Test signal: CVBS
Inspection item
- Video performance test
Inspection Distance - 1.8 M ~2.5 M
Criteria
- Check any abnormal color, line distortion or any
noise on the screen.
Motion video
2. S-Video (for X1161/X1161A/X110/X1261/H5360)
Procedure
- Test equipment: DVD player
- Test signal: S-Video
Inspection item
- Video performance test
Inspection Distance - 1.8 M ~2.5 M
Criteria
- Check any abnormal color, line distortion or any
noise on the screen.
3. HDTV/ Component
Procedure - Test equipment: DVD player
- Test signal: Ycbcr/YPbPr
Inspection item
- HDTV performance test
InspectionDistance - 1.8 M ~2.5 M
Criteria
- Check any abnormal color, line distortion or any
noise on the screen.
4. Audio Test (for X1261/H5360)
Procedure - Test equipment: DVD Player
- Test signal: CVBS
Inspection item - Audio performance test
Inspection Distance - 1.8 M ~2.5 M
Criteria - Check the sound from speaker
- Plug Audio cable into Audio In port, check
if "Volume" is normal.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-
- Adjust the volume to maximum by using the remote controller.
- Check the sound from speaker.
- Check if the "mute" is normal.
5. HDMI Test (for H5360)
Procedure - Test Signal : 720p,1080i
- Test Pattern : Any Pattern
- Equipment: DVD Player with HDMI output
Inspection item - HDMI Test
Criteria - Ensure the image and audio are well performed and the color can not discolor.
4-9 Optical Performance Measure
Inspection Condition
- Environment luminance: 2 Lux
- Product must be warmed up for 3 minutes
- Distances from the screen: 2.38 M
- Screen Size: 60 inches diagonal
1. Test equipment
Procedure - Connect VGA IN port of Projector with VGA port of Chroma by VGA cable, press "Menu" button, get into OSD mode, the settings are as below:
- "Display mode" is "Bright", "Brightness" is "50", "Contrast" is "70", and the "Format" is "4:3".
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-10
2. Brightness
Procedure - Full white pattern
- Use CL100 to measure brightness values of P1~P9.
- Follow the brightness formula to calculate brightness values.
☼ Brightness Formula
Criteria
Avg. (P1~P9)*1.1m2
Full white pattern
● 1100 ANSI lumen
3. Full On/Full Off Contrast
Procedure
- Full white pattern & full black pattern
- Use CL100 to measure brightness values of full white
pattern P5 & full black pattern B5
- Follow Contrast formula to calculate contrast values.
Full black pattern
☼ Contrast Formula
P5/B5
Note: P5
�����������������������������������������
= Lux of center in full white pattern
B5 =Lux of center in full black pattern
Criteria
● 2500: 1 (for X1161/X1161A/X1161N/X110)
● 2100: 1 (for X1261)
● 2300: 1 (for H5360)
4. Uniformity�
Procedure
- Full white pattern
- Use CL100 to measure brightness values of P1~P9
(see image: full white).
- Follow the Uniformity formula to calculate average values.
☼ Uniformity Formula
JBMA Uniformity = Avg. (P1, P3, P7, P9)/P5 X100%
Criteria
● 65%
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-11
4-10 Others
1. Function Inspection
General
- All OSD functions must be checked for functionality.
When OSD menu is displayed, there shall be no
visible peaking, ringing, streaking, or smearing
artifacts on the screen.
Factory Default
- The factory settings (with appropriate centering,
size, geometry distortion, etc.) shall be displayed
upon “Recall” is selected from OSD.
Display Size
- All preset modes shall expand to full screen size
using OSD Horizontal and Vertical Size controls.
Display Data Channel - The purpose of the DDC test is to verify the
(DDC)
DDC1/DDC2B operation of the projector and to
verify Plug & Play function.
Acoustic
- High pitch sound from cooling fan and color wheel is
unacceptable.
2. Check points for exterior and print pattern
Check item
Text & Pattern
Exterior
Focus ring
Logo
Check point
Missing letters & pattern or blurry prints are
unacceptable.
Dirt, scrape, water ripples and uneven color are
unacceptable.
Focus ring is functioning smoothly.
Missing logo, missing prints and blurry prints are
unacceptable
Screw
All screws should be fixed and in right type.
Pedestal
Well-functioned
Lamp Cover
It should be locked in the correct place.
Plastic Parts
Safety or warning
label
All plastic parts can not be broken and damaged.
All safety and warning labels should be visible,
including all contents.
All interface connectors should be complete and
workable.
Connector
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
4-12
Chapter 5
Firmware Upgrade
5-1 Equipment Needed
Software: (DDP 2430 for X1161/X1261/X1161A/X1161N/X110)
(DDP 2431 for H5360)
- DLP Composer Lite 9.2
- Firmware (*.img)
- Library file (X1161 X1261 FlashDeviceParameters) (library file has to put in PC and set right path in 5-4 step 4)
Note: - Please download "DLP Composer Lite 9.2" and "X1161 X1261 FlashDeviceParameters" from website to upgrade FW procedure.
Hardware:
- Projector
- Power cord: 42.50115G001
- RS232 cable: 42.83618G001 (for X1261/H5360)
- USB Cable: 42.87304G001 (for X1161/X1161A/X1161N/X110)
- PC or Laptop
Note: - The FW Upgrade procedure for X1161A/X1161N/X110/H5360 is the same as X1161, we take X1161 for example here.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
5-
5-2 DLP Composer Lite Setup
Procedure
1. Choose "DLP Composer Lite V9.2 Setup"
Program.
2. Click "Next".
3. Read "License Agreement".
-C
hoose "I accept and agree to be bound
by all the terms and conditions of this
License Agreement".
- Click "Next".
4. Click "Next".
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
5-
5. Click "Next".
6. Click "Next".
7. The program is executing "installing" status.
8. Click "Finish".
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
5-
5-3 USB Driver Upgrade Procedure (for X1161/
X1161A/X1161N/X110)
1. Set-up
-H
old on "power" button and plug in the
power cord.
- The power LED lights red and blue simultaneously after 5 seconds, then loosen "power" button.
- Connect projector with PC by USB cable.
(1)
2. Execute Program
(1) "Found New Hardware Wiszard" picture will appear on the screen.
(2) Select "Install the software automatically (Recommended)".
(2)
(3)
(3) Click "Next".
(4) Searching picture, please wait for several seconds.
(5) Click "Finish", then the USB driver has been installed successfully.
Note: - If you have installed the USB driver, there is no need to perform this action.
(5)
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
5-
5-4 Firmware Upgrade Procedure
1. Set-up
-H
old on "power" button and plug in the power
cord.
- The power LED lights red and blue simultaneously after 5 seconds, then loosen
"power" button.
-C
onnect projector with PC by RS232 cable.
(for X1261/H5360)
Note: - Please connect projector with PC by USB cable. (for X1161/X1161A/X1161N/X110)
- The system fan and the lamp will not operate.
2. Execute the "DLP ComposerTM Lite 9.2" file.
3. Click "Edit" and "Perferences".
4. Click "Library".
-C
lick "Browse" and navigate to the directory
where you put the DLP Composer installation
files in.
- Click "X1161 X1261 FlashDeviceParameters" folder.
- Click "OK".
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
5-
5. Click "Communications".
- Select "Serial Port". (for X1261/H5360)
- Select "USB". (for X1161/X1161A/X1161N/ X110)
for X1261/H5360
- Select the COM port which you are using. (for X1261/H5360)
- Click "Configure". (for X1261/H5360)
A
6. For X1261/H5360:
"Serial Port Configuration" picture will appear on the screen.
- Confirm the settings are as the picture A.
- Click "OK".
7. Click "OK".
8. Choose "Flash Loader".
-C
lick "Browse" to search the firmware file
(*.img).
- Click "Open".
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
5-
9. Select "Complete Image Download", then click "Reset Bus" to erase the flash memory.
10. If the FW is ready, click "Start Download"
to execute the firmware upgrade.
- Click "Yes".
11. It takes about several minutes, the firmware upgrade process is finished, "Download completed" will appear on the screen.
-U
nplug RS232 cable and power cord.
(for X1261/H5360)
Note: Please unplug USB cable and power cord. (for X1161/X1161A/X1161N/X110)
12. Check FW version. - Re-plug in power cable, then restart the unit and get into the Service Mode to check the firmware version.
( To get into Service Mode, please press
"Power", "Left", "Left" and "Menu" buttons
sequentially on remote controller.)
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
5-
5-5 Waveform Download
- Hold on "power" button and plug in the power cord.
- After 2 seconds, the power LED will flash blue, then loosen "power" button.
- After 5 seconds, the projector will automatically get into standby status.
- Waveform Download is completed.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
5-
Chapter 6
EDID Upgrade
6-1 EDID Introduction
Extended Display Identification Data is a VESA standard data format that contains basic
information about a display device and its capabilities, including vendor information,
maximum image size, color characteristics, factory pre-set timings, frequency range limits,
and character strings for the monitor name and serial number.
The information is stored in the display and is used to communicate with the system
through a Display Data Channel (DDC), which sites between the display device and the
PC graphics adapter. The system uses this information for configuration purposes, so the
monitor and system can work together.
Note: - The EDID Upgrade procedure for H5360/X1161/X1161A/X1161N/X110 is the same as
X1261, we take X1261 for example here.
- As for H5360, it needs to upgrade EDID for HDMI port.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
6-
6-2 Equipment Needed
Software
- EDID Program
- EDID File (*.ini)
Hardware
- Projector
- Power Cord for Projector (42.53506G002)
- VGA Cable (42.87305G102)
- HDMI(M) to DVI(F) Adapter (42.82B13G001) (for H5360)
- DVI Cable (42.83N06G001) (for H5360)
- RS-232 9 Pin Cable (pin to pin, F-M) (42.83C07G001)
- Generic Fixture (80.00001.001) for EDID Key-in (Fixture: JP3 must be closed)
- Power Adapter (47.57803G001)
- Monitor
- PC
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
6-
6-3 Setup Procedure (VGA)
VGA Cable
1. Connect all ports
P3
(1) Connect P1 of fixture with COM Port of PC/Laptop by RS232 Cable.
(2) Connect P3 of fixture with VGA Port of projector by VGA Cable.
(3) Plug Power Adapter to JP1 of fixture.
(4) Plug Power Cord to projector.
JP1
Adapter
JP3
P1
RS232 Cable
Note: You must confirm that the JP3 is closed.
Power Port
VGA Port
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
6-
6-4 EDID Key-In Procedure
1. Execute EDID Program
- Double click "EDID" to execute EDID program.
2. Process
(1) Select the COM Port which you are using.
(2) Click "Model".
(2)
(3) Select the source file (*.ini).
(4) Click "Open".
(5) Key in the Serial Number into the Barcode blank space.
(1)
(6) In "Write Source Select" item, select "Analog".
(7) Click "Program".
(3)
(4)
(5)
(7)
(6)
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
6-
3. Change the cable to Analog
- When the message "Please change the cable to Analog" appear on the screen, click "OK".
4. When the EDID program is completed, a message "OK" will appear on the screen.
5. Read EDID "Analog" information
- In "Read item", select "Analog" and "Trans", then click the "Read" button.
6. EDID informations will show the result.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
6-
6-5 Un-lock SNID and Default Language Reset
(1) Hold on "power" button then plug in the power cord.
Note: At this moment, power LED flashes red or blue altemately about 2 seconds, then the power LED flashes blue, then loosen "power" button.
(2) After flashing, LED is in steady condition and you can judge the actions as the
following table:
Power LED Status
Red
Blue + Red
Result
OK
Fail
Note: If it is fail, please do the actions as above steps item (1)-(2)
S/N General rule:
Use the last 1 digit code (as red word) for language information
Language Code (F)
1
2
3
4
5
6
7
8
Default Language
English
Thailand
Japan
TC
SC
Russian
Germany
Hungarian
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
6-
Appendix A (Exploded Image)
Note: This chapter is only designed to show the exploded image of the projector. For updated part numbers, please refer to RSPL report.
D.C. X1161
25
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
Item
P/N
1
2
3
4
5
7
8
70.8CP01G001
70.8CP08G001
70.8CP07G001
70.8CP04G001
70.8CP03G001
SP.8CP01GC01
70.8CP06G001
70.8CP24GR01
51.8CP03H001
61.8CP13G001
9
61.00018G003
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
61.8CP07G001
85.1A126G060
85.1A123G060
75.8CP04H001
51.8CP15G001
51.8CP18G001
52.8CP07G001
52.8CP11H001
41.87C05G001
41.83N02G001
41.8BB02G001
41.89B02G001
41.87F04G001
61.87340G001
52.8CP09G001
35.8CP02H001
6
Description
Parts Supply
BOTTOM MODULE X1161
ENGINE MODULE X1161
FAN SHIELDING MODULE X1161
IO MODULE X1161
FRONT MODULE X1161
LAMP MODULE FOR PROJECTOR X1161
LAMP MODULE X1161
ASSY LAMP COVER MODULE X1161 (SERVICE)
LAMP COVER LN2520 X1161
LAMP COVER AL FOIL X1161
LOCK SCREW PAN MECH M3*8.5-3.5 BLACK
(1018+HEAT TREATMENT)
TOP SHIELDING SECC X1161
SCREW PAN MECH M2.6*6 Ni
SCREW PAN MECH M3*6 NI
ASSY TOP COVER X1161
MYLAR LIGHTCUT ENG-BLOWER X1161
MYLAR FOR LENS X1161
SPONGE LIGHTCUT ZOOM X1161
SPONGE POWER BUTTON X1161
EMI GASKET W13*H3*L40
EMI GASKET / 6*6*55
EMI GASKET H30*L30*W10
EMI TAPE W*20/L*70
EMI TAPE L25*W16
STAND OFF M3*4L D8.0 2100MP
SPONGE LIGHTCUT FR-CW X1161
NAME LABEL X1161
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
V
V
II
D.C. X1261
25
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
III
Item
P/N
1
2
3
4
5
7
8
70.8CQ04G001
70.8CQ03G001
70.8CP07G001
70.8CQ01G001
70.8CP03G001
SP.8CP01GC01
70.8CP06G001
70.8CP24GR01
51.8CP03H001
61.8CP13G001
9
61.00018G003
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
61.8CP07G001
85.1A126G060
85.1A123G060
75.8CP04H001
51.8CP15G001
51.8CP18G001
52.8CP07G001
52.8CP11H001
41.87C05G001
41.83N02G001
41.8BB02G001
41.89B02G001
41.87F04G001
61.87340G001
52.8CP09G001
35.8CQ03H001
6
Description
Parts Supply
BOTTOM MODULE X1261
ENGINE MODULE X1261
FAN SHIELDING MODULE X1161
IO MODULE X1261
FRONT MODULE X1161
LAMP MODULE FOR PROJECTOR X1161
LAMP MODULE X1161
ASSY LAMP COVER MODULE X1161 (SERVICE)
LAMP COVER LN2520 X1161
LAMP COVER AL FOIL X1161
LOCK SCREW PAN MECH M3*8.5-3.5 BLACK
(1018+HEAT TREATMENT)
TOP SHIELDING SECC X1161
SCREW PAN MECH M2.6*6 Ni
SCREW PAN MECH M3*6 NI
ASSY TOP COVER X1161
MYLAR LIGHTCUT ENG-BLOWER X1161
MYLAR FOR LENS X1161
SPONGE LIGHTCUT ZOOM X1161
SPONGE POWER BUTTON X1161
EMI GASKET W13*H3*L40
EMI GASKET / 6*6*55
EMI GASKET H30*L30*W10
EMI TAPE W*20/L*70
EMI TAPE L25*W16
STAND OFF M3*4L D8.0 2100MP
SPONGE LIGHTCUT FR-CW X1161
NAME LABEL X1261
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
V
V
IV
I.D. X1161
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
Item
P/N
70.8CP26GR01
1
2
3
4
5
6
7
8
9
10
11
12
13
14
51.8CP02H001
52.88N07G001
86.0A123G024
61.8CP06G001
70.8CP05G001
51.8CP12G001
70.8CP14G001
75.8CP02G001
61.88T19G001
75.8CP03GP01
85.1A123G060
51.88T21G001
42.00454G001
41.89B02G001
41.89C06G001
15
85.1C224G051
Description
Parts Supply
ASSY BOTTOM COVER MODULE X1161
(SERVICE)
BOTTOM COVER MN3600H X1161
ADJUSTABLE FOOT RUBBER,EP721
HEX NUT M3*5.5*0.5P L2.4 Ni
BOTTOM SHIELDING SECC (for X1161)
BOTTOM SHIELDING MODULE (for X1261)
MYLAR LVPS X1161
LAMP DRIVER MODULE X1161
ASSY INTERRUPT SWITCH MODULE X1161
AC INLET BRACKET FOR X1160E
LVPS 180W X1161 STB<1W CT-258A
SCREW PAN MECH M3*6 NI
MYLAR K-LOCK 0.25t X1160
W.A 8P 120mm MB TO LVPS X1160
EMI TAPE W*20/L*70
EMI GASKET L44*H1*W21
SCREW PAN MECH M4*5 COLOR W/TOOTH
WASHER Cr3+
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
V
VI
Front Module
Item
P/N
1
2
3
4
5
6
51.88T24G001
80.8CP05G001
51.8CP09H001
85.3A122G040
61.8CP14H001
52.8CP09G001
Description
Parts Supply
FRONT IR CAP FOR X1160E
PCBA IR SENSOR BD FOR X1161
FRONT COVER MN3600H X1161
SCREW CAP MECH M2*4 Ni
ACER LOGO FOR X1161
SPONGE LIGHTCUT FR-CW X1161
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
V
VII
IO MODULE X1161
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
VIII
Item
P/N
Description
1
61.8CP10G001
70.8CP25GR01
80.8CP01G001
35.8CP01H001
51.8CP13G001
51.8CP16G001
51.8CP11H001
52.8CP10G001
85.005AGG408
85.1A123G060
41.87F02G001
41.8CP01G001
70.8CP23GR01
52.8CP08G001
61.8CP11G001
41.82G03G001
MAIN SHIELDING SMALL TINPLATE X1161
ASSY MAIN BOARD MODULE X1161 (SERVICE)
PCBA MAIN BOARD FOR X1161
LABEL IO X1161
MYLAR MAIN-BD TO LVPS X1161
MYLAR MAIN-BD SMALL X1161
IO COVER MN3600H X1161
SPONGE LIGHTCUT IO X1161
SCREW HEX I/O #4-40 H4*L8 NI NYLOK
SCREW PAN MECH M3*6 NI
EMI GASKET W4*H1*L120
EMI TAPE L110*W20
ASSY IO COVER MODULE X1161 (SERVICE)
SPONGE LIGHTCUT MAINSHIELDING X1161
MAIN SHIELDING SMALL BRKT TINPLATE X1161
EMI GASKET USB CONNECTOR EP719
2
3
4
5
6
7
8
9
10
11
12
13
14
Parts Supply
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
IX
IO MODULE X1261
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
Item
P/N
1
61.8CP09G001
70.8CQ09GR01
80.8CQ01G001
35.8CQ02H001
51.8CP13G001
51.8CP14G001
70.8CQ08GR01
51.8CQ01H001
52.8CQ01G001
85.005AGG408
85.1A123G060
41.88T02G001
41.89B01G001
52.8CP08G001
2
3
4
5
6
7
8
9
10
11
12
Description
Parts Supply
MAIN SHIELDING TINPLATE X1161
ASSY MAIN BOARD MODULE X1261 (SERVICE)
PCBA MAIN BOARD FOR X1261
LABEL IO BASE X1261
MYLAR MAIN-BD TO LVPS X1161
MYLAR MAIN-BD X1161
ASSY IO COVER MODULE X1261 (SERVICE)
IO COVER MN3600H X1261
SPONGE LIGHTCUT IO X1261
SCREW HEX I/O #4-40 H4*L8 NI NYLOK
SCREW PAN MECH M3*6 NI
EMI GASKET L180*W4*H1
EMI TAPE L*190/W*13
SPONGE LIGHTCUT MAINSHIELDING X1161
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
XI
Bottom Shielding Module
Item
P/N
1
2
3
4
61.8CP06G001
61.8CP08G001
49.8CQ01G001
52.8CP05G001
Description
Parts Supply
BOTTOM SHIELDING SECC X1161
SPEAKER BRKT SUS301 X1161
SPEAKER 2W 16OHM DAB128 90mm X1261
SPONGE SPEAKER X1161
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
XII
One- Fan Module
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
XIII
Item
P/N
1
49.8CP02G001
2
3
4
5
6
7
8
9
10
11
61.88T05G041
61.8AN01G002
85.1F123G260
85.1A123G060
51.88T18G001
41.89B02G001
52.88T01G001
52.88T08G001
52.89T01G001
51.81540G001
12
49.8CS01G001
13
52.82G08G001
Description
Parts Supply
SUNON 70*70*20mm AXIAL FAN, KDE1207PKV1.
MS.B3001.AF.GN
SHIELDING TWO FAN PDG-DSU30
LAMP BLOWER DUCT X15 GENERIC
SCREW PAN MECH E/SF M3*26 Ni
SCREW PAN MECH M3*6 NI
KAPTON 10*10 0.05t X1160
EMI TAPE W*20/L*70
FAN SHELDING FRONT AIR TIGHT CVS X1160
FAN SHELDING AIR TIGHT F12 X1160
BLOWER AIR TIGHT F12 H5350
TAPE 3M J350 17*60mm
SUNON 45*20mm GB1245PKV1-8AY, F TYPE
BLOWER FAN
BLOWER 4520 RUBBER EP7190
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
XIV
Engine Module
Item
P/N
1
70.8CP09G001
1
2
3
4
5
6
7
70.8CQ02G001
51.8CP04H001
51.8CP08H001
51.89Z04G001
85.1A326G060
85.WA321G040
41.89C01G001
Description
Parts Supply
ASSY OPTICAL ENGINE MODULE Z15 (S450)
(for X1161)
ASSY OPTICAL ENGINE MODULE (for X1261)
FOCUS RING MN3600H X1161
ZOOM RING MN3600H X1161
ZOOM RING FIXED HOLDER EX330
SCREW PAN HEAD MECH M2.6*6 BLACK
SCREW PAN TAP M1.7*4 BLACK
EMI TAPE L45*W30
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
XV
Assy Engine Module
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
XVI
Item
P/N
Description
1
2
3
4
5
6
7
23.8CP01G001
70.8CP15G001
23.8AH20G001
70.8CP22GR01
70.8CQ07GR01
85.1A526G060
80.8CP02G001
70.8CP13G001
70.8CP10G001
8
48.8EH01G001
8
48.8CQ01G001
9
10
11
52.8CP01G001
52.8CP02G001
85.4A826G118
12
52.8CP04G001
13
14
15
16
17
18
19
70.8CP11G001
61.8CP02G001
70.8CP12G001
61.8EF03G001
23.8AH20G002
61.88N13G002
61.88N12G001
YO YM39 PROJECTION LENS 1.1X ZOOM
ASSY RELAY MODULE Z15
CONDENSER1 FOR A15W
ASSY ENGINE MODULE X1161 (SERVICE)
ASSY ENGINE MODULE X1261 (SERVICE)
SCREW PAN MECH M2.6*6 Ni NYLOK
PCBA DMD BOARD FOR X1161
ASSY ROD MODULE Z15
ASSY ENGINE BOTTOM COVER Z15
0.55” SVGA 2xLVDS SERIES 450 DMD -8 TI
8060-603cB
0.55” XGA 2xLVDS SERIES 450 DMD -8 TI
1076-603cB
DMD RUBBER X1161
DMD BOARD RUBBER X1161
STEP SCREW FOR TYPEX DMD M2.6*11.8mm,X15
S450 0.55” XGA/SVGA DMD thermal pad, FUJIPOLY, Sarcon XR-HE, 18.4x12.5x0.5 mm
ASSY ENGINE BASE Z15
DMD HEATSINK X1161
ASSY COLOR WHEEL MODULE Z15
CONDENSER LIGHT STOP EX615
CONDENSER 2 FOR A15W
ROD COVER NEW SUS301 X15
ROD SPRING SUS301,X15
Parts Supply
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
V
V
V
V
V
XVII
Assy Color Wheel Module Z15
Item
P/N
Description
1
2
3
4
61.8CP03G001
80.8CP04G001
23.8EF19G001
85.1A126G040
5
51.82Y29G001
6
7
70.8CP21GR01
52.83615G001
61.83628G001
CW BRACKET SECC X1161
PCBA PHOTO SENSOR BOARD FOR X1161
YO 6S R81Y41G84C31W52B71_HE3 CW
SCREW PAN MECH M2.6*4 Ni
TAPE 3M J350 10*5mm FOR COLOR WHEEL
DP715
ASSY COLOR WHEEL MODULE X1161 (SERVICE)
COLOR WHEEL DISC RUBBER, EzPro755
COLOR WHEEL SHOULDER SCREW,EzPro755
Parts Supply
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
XVIII
Assy Lamp Driver Module
Item
P/N
Description
1
51.88T11G003
2
75.8BA01G002
3
4
5
85.1A123G060
85.3A122G040
42.00422G001
6
42.00447G001
7
42.00436G002
8
9
10
11
52.88T02G001
52.88T03G001
51.88T18G001
52.86K01G001
HOLDER LAMP DRIVER FOR H5350
ASSY OSRAM LAMP DRIVER O6 MIC 180W
(Gen5_Panyu+E20.8)
SCREW PAN MECH M3*6 NI
SCREW CAP MECH M2*4 Ni
W.A 5P 150mm LAMP DRIVER TO MB X1160
CABLE W.A. 2P #20 180mm LVPS TO LAMP DRIVER FOR X1260K
CABLE W.A. 2P #22 100mm LAMP DRIVER TO
LAMP X1160
LAMP DRIVER HOLDER AIR TIGHT F12 X1160
LAMP DRIVER HOLDER AIR TIGHT-FR F12 X1160
KAPTON 10*10 0.05t X1160
LAMP SPONGE F12 35X5X3.2mm EP709
Parts Supply
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
V
XIX
A.K.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
XX
Item
P/N
Description
1
2
42.87205G001
42.00200G002
3
42.00110G011
4
42.00120G011
5
6
36.00006G031
36.00027G001
7
51.86213G002
8
9
36.8CP02G001
35.82001G111
10
36.8CP01H001
11
45.8CP01G001
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
36.00029G001
56.8CP01G001
56.8CP02G001
75.8CP05H001
51.52109G005
DC.8CP01G001
35.52302G091
51.00200G001
51.00201G001
55.8CP01G001
35.82V02G001
57.00001G001
53.88T01G001
35.8CP03G001
35.86301G001
CABLE COMPOSITE VIDEO 1.8M 3200MP
CABLE VGA 15P 1.8M BLK EP739
CABLE POWER CORD 1.8M SP-60/IS-14 UK DISWARNING LABEL
CABLE POWER CORD 1.8M SP-023/IS-14 EUROPE DIS-WARNING LABEL
WARRANTY CARD ,EUROPE FOR ACER
SERVICE STATION CARD
PE BAG ZIPPER #9 W/RECYCLING MARK FOR
OPTOMA
QUICK START CARD MULTILINGUAL
AK LABEL 3”*3” BLANK
USER’S GUIDE MULTILINGUAL (CD) ACER X1161/
X1261
INFRARED REMOTE CONTROLLER X1161 X3
“BONTECH”
SECURITY CARD FOR ACER
AIR BAG RIM X1161
AIR BAG TOP-BOTTOM X1161
BUY ASSY LENS CAP X1161
PE BAG 450*350*0.07 FOR OPTOMA EP720
D.C. X1161
LABEL CARTON 108*92 BLANK
HANDLE BAR 2. PE HD70
HANDLE BAR 1.PE HD70
CARTON CARRY BOX X1161
LABEL CARTON(SEAL) 110*50mm PD120
PACK SIO2 DRIER 20g
SOFT CARRY BAG X1160
LABEL CARTON STICKER X1161
SPEC LABEL BLANK PD120
Parts Supply
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
V
V
XXI
Appendix B
I. Serial Number System Definition
Serial Number Format for Projector (take X1261 for example)
EYK0201001
1 915
00000
2 3 59
0
1
4
5
6
1
:
EYK0201001 = Part Number
2
:
915 = Date Code (ex:2009 = 9, the fifteenth week of the year = 15)
3
:
00000 = Serial Numbers
4
:
59 = Manufacturing Code
5
:
0 = Version Code
6
:
1 = Auto-Language Code
EX: EYK0201001915000005901
This label represents the serial number for X1261. It is produced at CPC on fifteenth week
of 2009. Its serial code is 00000.
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
I
II. PCBA Code Definition
PCBA Code for Projector
A B
1
XXX
2
XXXXXXXXX CC
3
4
5
XXX EEEE
6
7
1
:
ID
2
:
Vendor Code
3
:
Firmware Version
4
:
P/N
5
:
MB version
6
:
Date Code
7
:
S/N
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
II
Appendix C
RS232 function command summary table (for X1261/H5360)
General command type (Projector “receives” commands)
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Code (character)
OKOKOKOKOK\r
* 0 IR 001\r
* 0 IR 002\r
* 0 IR 004\r
* 0 IR 006\r
* 0 IR 007\r
* 0 IR 008\r
* 0 IR 009\r
* 0 IR 010\r
* 0 IR 011\r
* 0 IR 012\r
* 0 IR 014\r
* 0 IR 015\r
* 0 IR 017\r
* 0 IR 018\r
* 0 IR 019\r
* 0 IR 021\r
* 0 IR 022\r
* 0 IR 023\r
* 0 IR 024\r
* 0 IR 025\r
* 0 IR 026\r
* 0 IR 027\r
* 0 IR 030\r
* 0 IR 031\r
* 0 IR 032\r
* 0 IR 033\r
* 0 IR 034\r
* 0 IR 035\r
Function feature
Power On
Power On
Power Off
Keystone
Mute
Freeze
Menu
Up
Down
Right
Left
Re-Sync
Source Analog RGB for D-sub
Source PbPr for D-sub
Source S-Video
Source Composite Video
Aspect ratio 16:9
Aspect ratio 4:3
Volume +
Volume –
Brightness
Contrast
Color Temperature
Hide
Source
Video: Color saturation adjustment
Video: Hue adjustment
Video: Sharpness adjustment
Query Model name
X1161/X1261/X1161A/X1161N/X110/H5360 Confidential
I
No
30
31
32
33
34
35
36
37
Code (character)
* 0 IR 036\r
* 0 IR 037\r
* 0 IR 042\r
* 0 IR 043\r
* 0 IR 046\r
* 0 IR 047\r
* 0 IR 048\r
* 0 IR 049\r
Function feature
Query Native display resolution
Query company name
Keystone Up
Keystone Down
Zoom
e-Key
Color RGB
Language
Note: The command with end "\r" means "Enter".
X1161/X1261/X1161A/X1161N/X110
Confidential
II