Maxtor 4 Channel Stand-alone DVMR User`s manual

4Ch H.264 Hardware Codec
H.264 Network DVR
User¡s Manual
VER 1.0
4 Channel Network DVR
Real-time playback / USB backup
The most stable and reliable real stand alone Digital Video Multiplex Recorder
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
Installation & Safeguards
INSTALLATION & SAFEGUARDS
All the safety and operating instructions should be read before the unit is operated.
Environment Condition for Installation
1. To prevent electric shock or other hazard, do not expose units to rain, moisture, or dust.
2. Place this unit in a well-ventilated place and do not place heat-generating objects on this unit.
3. This unit should not be located in an area where it is likely to be subjected to mechanical shocks.
Before You Start
1. Ensure the power switch is in the OFF position prior to starting.
2. Do not attempt to open or remove the covers. That may expose you to dangerous voltage or
other hazards.
3. Installation should be performed by qualified service personnel only.
4. This unit should be operated only from the type of power source indicated on the manufacturer¡s
label and with the power supply included with the unit.
Notice
1. Before initial configuration or operation you must first set the TIME/DATE, followed by HDD clear.
If you don¡t follow this steps first, that may cause non recording on the HDD or non saving
setting value. Even though it is recorded, you cannot search recorded data.
2. When it comes to HDD capacity, you can use a big size of HDD.
3. When you set the record setup, you have to set the Record Configuration and also Schedule
Setup. This unit records as per the Record type & Schedule setup. The default setting value for
Schedule setup is Continuous mode.
1
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
Contents
Contents
CHAP. 1
Features & Package Contents
----------------------------------------------------------------
4
1-1.
Features
----------------------------------------------------------------
4
1-2.
Package Contents
----------------------------------------------------------------
5
Function of Each Button
----------------------------------------------------------------
6
2-1.
Front
----------------------------------------------------------------
6
2-2.
Rear
----------------------------------------------------------------
7
Installation
----------------------------------------------------------------
8
3-1.
Installation Configuration
----------------------------------------------------------------
8
3-2.
Detailed Installation
----------------------------------------------------------------
9
1)
HDD(Hard Disk Drive)
----------------------------------------------------------------
9
2)
Camera
----------------------------------------------------------------
9
3)
Monitor
----------------------------------------------------------------
10
4)
Power
----------------------------------------------------------------
10
5)
Other External Device
----------------------------------------------------------------
11
6)
RS-232 ASCII-Code
----------------------------------------------------------------
11
Operation
----------------------------------------------------------------
12
4-1.
System Log In
----------------------------------------------------------------
12
4-2.
Factory Default
----------------------------------------------------------------
12
4-3.
Display Configuration
----------------------------------------------------------------
13
4-4.
Live View Setup
----------------------------------------------------------------
14
1)
Full / Multiple View
----------------------------------------------------------------
14
2)
SEQ
----------------------------------------------------------------
14
3)
PIP View
----------------------------------------------------------------
14
4)
ZOOM View
----------------------------------------------------------------
14
5)
Freeze
----------------------------------------------------------------
14
4-5.
Record
----------------------------------------------------------------
15
4-6.
Playback
----------------------------------------------------------------
15
4-7.
Search
----------------------------------------------------------------
16
4-8.
PTZ Camera Operation
----------------------------------------------------------------
17
4-9.
Data Back-up
----------------------------------------------------------------
17
CHAP. 2
CHAP. 3
CHAP. 4
2
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
CHAP. 5
- Network DVR
Contents
Set up
----------------------------------------------------------------
18
5-1.
General Operation
----------------------------------------------------------------
18
5-2.
Display Setup
----------------------------------------------------------------
19
1)
VGA Setup
----------------------------------------------------------------
19
2)
Screen Display Setup
----------------------------------------------------------------
19
2)
OSD Setup
----------------------------------------------------------------
20
Record
----------------------------------------------------------------
21
1)
Record Setup
----------------------------------------------------------------
21
2)
Schedule Setup
----------------------------------------------------------------
22
Configuration
----------------------------------------------------------------
23
1)
HDD Management
----------------------------------------------------------------
23
2)
Time/Date Setup
----------------------------------------------------------------
24
3)
Camera Setup
----------------------------------------------------------------
24
4)
Motion Setup
----------------------------------------------------------------
25
5)
Interval Setup
----------------------------------------------------------------
26
6)
Alarm Setup
----------------------------------------------------------------
26
7)
Password Setup
----------------------------------------------------------------
26
External Device Setup
----------------------------------------------------------------
27
1)
TCP/IP Setup
----------------------------------------------------------------
27
2)
Pan Tilt Zoom Setup
----------------------------------------------------------------
28
3)
Spot Setup
----------------------------------------------------------------
28
Back up
----------------------------------------------------------------
29
1)
CDR Setup
----------------------------------------------------------------
29
2)
USB Setup
----------------------------------------------------------------
29
Firmware Upgrade
----------------------------------------------------------------
30
Network Setup
----------------------------------------------------------------
31
6-1.
DVR Network Configuration
----------------------------------------------------------------
31
6-2.
Remote Viewer Program
----------------------------------------------------------------
35
6-3.
Backup CD Player
----------------------------------------------------------------
40
CHAP. 7
Web Viewer Setup
----------------------------------------------------------------
42
7-1.
Registering DVR for DDNS
----------------------------------------------------------------
42
7-2.
DDNS Setup in DVR
----------------------------------------------------------------
44
7-3.
Web Viewer
----------------------------------------------------------------
48
7-4.
Web Backup Player
----------------------------------------------------------------
49
7-5.
Web Backup
----------------------------------------------------------------
51
Specifications
---------------------------------------------------------------3
54
5-3.
5-3.
5-4.
5-5.
5-6.
CHAP. 6
CHAP. 8
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP 1. Features & Package Contents
CHAP 1. Features & Package Contents
1-1. Features
Live Display
Real time display per camera
Auto Sequence
PIP (Picture in picture)
Digital Zoom of display
Simple playback mode
Simple PTZ camera control
Record
Efficient Image Quality step in 6 steps
Schedule recording
Event Record by alarm and motion detection
Network
Monitoring and Search by using Remote Viewer via network
Playback
Search and playback by recorded data size and date/time
Various steps in forward playback speed (X2, X4, X8, X16, X32 fast playback. 1/16, 1/8 ,1/4,
1/2 slow playback)
Various steps in backward playback speed (X2, X4, X8, X16, X32 fast playback. 1/16, 1/8, 1/4,
1/2 slow playback)
Data backup
Remote viewer backup in AVI, JPEG file
Supports bigger capacity of HDD
USB Device Back-Up available
Others
Supports UNI-CODE
Supports SPOT Monitor
PAL/NTSC Auto detection
4
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP 1. Features & Package Contents
1-2. Package Contents
NETWORK DVR
POWER HDD ACTIVE
USB
1. DVR Main Unit
2. Power Cable
5. Software CD
3. Power Adapter
4. User¡s Manual
6. Rubber Pad
7. HDD absorber
8. Bolts
Package Contents
9. Mouse
Description
1. DVR Main Unit
Stand-Alone Digital Video Recorder
2. Power Cable
AC power supply to adapters for 12V DC power
3. Power Adapter
DC power supply
4. User¡s Manual
User¡s Manual
5. Software CD
Remote Viewer Software & Backup CD Player
6. Rubber Pad
Prevent DVR from slipping. Attach it to the bottom of main unit
7. HDD absorber
Absorbing the mechanical shock of HDD against the case bottom
8. Bolts
Bolts for fixing HDD
9. Mouse
A mouse controlling all functions of DVR
5
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP 2. Function of Each Button
CHAP 2. Function of Each Button
2-1. Front
2
1
Name
Function
① USB HOST
Used for Data Backup
② LED Lamps
Shows status of operation
6
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP 2. Function of Each Button
2-2. Rear
1
2
3
4
5
6
7
Name
1
Audio In/Out
2
RS 485
8
Function
1ch audio input/ 1ch audio output
Connection with PTZ camera or other external device using RS 485
interface
RELAY Output
Relay out terminal
SENSOR Input
Sensor input terminal
3
VGA
Connection to VGA Monitor (CRT type or TFT LCD monitor)
4
ETHERNET
5
CAMERA Input
6
MONITOR
Output
Connection with Composite Monitor (NTSC / PAL)
7
SPOT Monitor
Output
Connection with Composite Monitor (NTSC / PAL)
8
PS/2
9
DC Power
Connection to ETHERNET device
Connection with camera (NTSC / PAL)
Connection with PS/2 MOUSE
DC over 12V adapter
7
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
9
4Ch H.264 hardware codec
- Network DVR
CHAP. 3
CHAP.3 Installation
3-1. Installation Configuration
8
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
Installation
4Ch H.264 hardware codec
- Network DVR
CHAP. 3
Installation
3-2. Detailed Installation
1) HDD
MAIN BOARD
(
HDD
)
1. Connect Main Board and HDD using SATA data cable and HDD power cable.
2. Stick the HDD absorber (included in package) on the bottom of case and then install the
HDD on top of them by using the bolts (included in package).
3. Screws must be inserted from outside of the case bottom.
2) Camera
Connect camera to the camera input on rear panel of DVR marked CAMERA IN.
9
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 3
3) Monitor
Connect the video output marked MONITOR to Video-In of Main monitor.
4) Power
DC over 12V adapter
10
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
Installation
4Ch H.264 hardware codec
- Network DVR
CHAP. 3
Installation
5) Other External Device
RS-485 : Control external device like PTZ camera.
(Pin No.8 & No.9 at D-SUB).
RELAY Output : Relay Output (Pin No.6 & No.7).
SENSOR Input : Sensor Input ? Alarm Input (Pin No.1 ~ No.4).
ETHERNET : Connection to LAN, WAN
Audio Input : connect to a microphone
Audio Output: connect to a speaker
6) RS-232C ASCII-code
Following ASCII-Codes (Hexa-Code) are for programmers who want to control DVR unit via the
RS232C Port using keyboard of PC. ASCII-Code is 1 Byte.
녹화
¡R¡
DOWN
¡J¡
PTZ
¡T¡
CH1
¡1¡
STOP
¡S¡
LEFT
¡H¡
ZOOM
¡Z¡
CH2
¡2¡
재생
¡P¡
RIGHT
¡K¡
FRZ
¡F¡
CH3
¡3¡
Pause
¡A¡
NEXT
¡N¡
MODE
¡D¡
CH4
¡4¡
SERCH
¡E¡
ENTER
0x0d
PIP
¡I¡
MENU
¡M¡
-
¡<¡
SEQ
¡Q¡
UP
¡U¡
+
¡>¡
11
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 4
Operation
4-1. System Log-In
1) After power on, right-click of a mouse shows
icon bar on the screen. Then you click the
[Menu] icon
to log in.
2) Then, you will see ¡DVR Log-In¡ message
shown as right.
3) You may log in as a ADMIN, MANAGER, or
USER1 ~ USER8.
4) Input your password (Max. 8 digits are
available for password)
5) To exit, click ¡EXIT¡ button.
DVR LOG-IN
USER ID
USER PW
1
2
ADMIN
________
3
4
5
6
ENTER
7
8
9
EXIT
If the password entered matches previously set password, you can log into ¡MAIN MENU¡. If
an incorrect password is entered, you will see ¡PW IS NOT CORRECT¡ message on display.
The factory default password is none. Just click ¡ENTER¡ for first time initial log in.
-Factory default password
ADMIN : (Blank)
MANAGER : ¡1¡
USER1~USER8 : ¡2¡~¡9¡
※ For security reasons, be sure to make note of your own password.
4-2. Factory Default
Before first operation, you must check out each channel is displaying properly and log in
¡Main Menu¡ and set Time/Date and set HDD clear.
1. HDD Management
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
2. Factory Default
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
TIME/DATE SETUP
PASSWORD SETUP
LANGUAGE
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
12
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 4
Operation
4-3. Display Configuration
ETHERNET connection status icon
disconnected
HDD space display
(Recorded space in HDD)
connected
OVERWRITE status icon
Current Date/ Time display
* shown when overwrite is ENABLE
* not shown when overwrite is DISABLE
* blinking during OVERWRITE
PLAYBACK
SEARCH
FREEZE
Ch No.1 single display
SEQUENCE
Ch No.2 single display
ZOOM
PIP
Ch No.3 single display
PTZ
Ch No.4 single display
MENU
STOP
4 - split display
Live Display
HDD space display
(Location of the current playback image in HDD)
MENU
BACKWARD PLAY PER PICTURE
BACKWARD PLAY
PAUSE
FORWARD PLAY
FORWARD PLAY PER PICTURE
INCREASE PLAYBACK SPEED
DECREASE PLAYBACK SPEED
SEARCH
EXIT
Playback Display
13
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 4
Operation
4-4. Live View Setup
1) Full / Multiple View
CHAP. 4
사용방법
Move a cursor onto [4 - split icon]
in the icon bar and click it to view 4 channel division.
To enlarge each channel, click 1,2,3,4 Icon. Then, you will see a channel in full screen mode.
Full Screen
Full Screen
2) SEQ
Click ¡SEQ¡ icon. It automatically displays full screen images in sequence.
You can setup SEQ time interval on setup menu. (SCREEN SETUP ? SEQEUNCE INTERVAL)
CH04
CH03
●
●
CH02
●
CH01
CAM01
3) Picture in Picture (PIP View)
When it is in full screen display mode, you can see other camera in a
small window by clicking [PIP] icon
, the other camera in small
window is rotating in sequence to next number of camera and you can
set the rotating time interval as per the procedure in Main Menu SCREEN SETUP - PIP INTERVAL.
4) ZOOM View
In live mode, if you click [ZOOM] icon
, images are displayed in two times larger size.
While using [ZOOM] mode, you can move the enlargement area by using a mouse.
To exit ZOOM mode, click ZOOM] icon again.
5) Freeze
Click [FRZ] icon
in the icon bar to pause a live view temporarily.
14
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
CAM02
4Ch H.264 hardware codec
- Network DVR
CHAP. 4
Operation
4-5. Record
It records as a setting made by a user in Schedule Mode.
- Emergency Record
Once you click this icon
, it keeps recording continuously regardless of schedule setting.
- Schedule Record
Go to MAIN MENU-SCHEDULE SETUP and setup schedule as you want. It records as a setting.
- Record Icon in Red indicates Schedule Record, Motion record, and alarm record.
Record [RED]
Stop recording [WHITE]
- This DVR unit does not record in following conditions ;
※ When Over write function is off and HDD is full
※ When you back up recorded images by using CDRW burning.
※ When you update a firmware
※ When you are in HDD management menu mode
4-6. Playback
On record mode or stop mode, click [playback] icon
to play the recorded data in 1x speed.
* Please use a mouse pad for proper operation of a mouse. Otherwise, it may not operate properly.
15
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 4
Operation
4-7. SEARCH
There are three search methods controlled by a mouse wheel button, left and right button of a
mouse.
When you click [SEARCH] icon
, then you see a window shown as below.
Select a target data by using a mouse.
In PERCENT SEARCH Mode, you can select a certain data by clicking on the bar.
To move to the previous mode, click ¡ESC¡.
1. PERCENT SEARCH
Search by percentage of total recorded data. It starts from image corresponding to set % of
data on the search bar.
2. TIME/DATE SEARCH
Search by time & date. Playback starts from the time & date selected.
3. EVENT SEARCH
Search by event list (Motion, Alarm, Video Loss)
SEARCH
PERCENT SEARCH
PERCENT SEARCH
TIME/DATE SEARCH
EVENT SERACH
START
END
TARGET
EXIT
2006 / JUL / 09 PM 01 : 58 : 56
2006 / JUL / 10 PM 11 : 58 : 56
2006 / JUL / 09 PM 05 : 58 : 56
PERCENT
20
SERACH MAIN MENU
PLAY
ESC
PERCENT SEARCH
EVENT SEARCH
TIME/DATE SEARCH
START
END
2006 / JUL / 09 PM 01 : 58 : 56
2006 / JUL / 10 PM 11 : 58 : 56
TARGET
2006 / JUL / 09 PM 05 : 58 : 56
PLAY
ESC
DATE/TIME
CHANNEL EVENT
-------------------------------------/--/-- --:--:--------/--/-- --:--:--------/--/-- --:--:--------/--/-- --:--:--------/--/-- --:--:--------/--/-- --:--:--------/--/-- --:--:----PAGE
000/000
ESC
TIME/DATE SEARCH
EVENT SEARCH
16
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 4
Operation
4-8. PAN/TILT/ZOOM Camera Operation
Click [PTZ] icon
in the icon bar, then you can see ¡arrow¡ key & ¡+/-¡ key shown below.
Click these arrow keys to move a PTZ camera to each direction. By using ¡+/-¡ key, you can
control ZOON IN/OUT function. (¡+¡ : ZOOM IN / ¡-¡ : ZOOM OUT)
4-9. Data Backup
Right-click to see icon bar and click [MENU] icon
and go to ¡Backup¡.
1. Insert USB backup device and select the start time & date from which you want to back up.
※ The START & END time / date in HDD sub-menu only shows start and end of recording. This is
not selectable and editable.
2. To set start time of back-up and back-up data size, use a mouse (left/right/wheel button of a
mouse.
※ End time of back-up will be calculated automatically as per start time & date and the back-up
data size you set.
※ You can select the back-up data size (size of back-up data from start of back-up), but END of
back-up time is automatically determined by DVR itself.
3. Click ¡Back-up¡ then it starts USB back-up.
4. When back-up is completed, for the next USB back-up, start time of back-up shall be the end of
previous USB back-up, so that you can back-up from that time for continuous data back-up.
If you need another back-up, repeat the above procedure.
To stop backup, click ¡ESC¡.
※ During data back-up, it is impossible to cancel back-up process.
※ During data back-up, DVR does not record.
5. You can verify the back-up by installing and running the Backup Player on your PC.
BACK-UP
BACK-UP
HDD
START
END
2006/JUL/08 AM10:10:23
2006/JUL/09 AM08:12:23
HDD
START
END
CD-R
START
END
SIZE
2006/JUL/08 PM12:04:12
2006/JUL/08 PM08:12:23
700MB -> 0MB
CD-R
START
END
SIZE
BURN
ESC
2006/JUL/08 PM 12:04:12
2006/JUL/08 PM 08:12:23
2005/AUG/07 AM04:04:12
2005/AUG/08 PM08:12:23
700 MB - > 700MB
BURN
17
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
ESC
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
CHAP. 5 Set up
5-1. General Operation
Click [MENU] icon
and input user password to log in.
Mouse buttons
Mouse Wheel
Functions
Up and down of setup value on the Menu mode
Right
Decrease of setup value on the Menu mode
Left
Increase of setup value on the Menu mode
Execute all of the function (clicking icons)
MAIN MENU
DISPLAY SETUP
RECORD
CONFIGURATION
EXTERNAL DEVICE
BACK-UP
FIRMWARE UPGRADE
FACTORY DEFAULT
LANGUAGE
ENGLISH
EXIT
MAIN MENU
18
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
5-2. DISPLAY SETUP
This is setup menu for display on the screen.
If you click ¡DISPLAY SET UP¡, then you change setting values for display as shown below.
DISPLAY SETUP
VGA SETUP
SCREEN DISPLAY
OSD SETUP
ESC
1) VGA SETUP
VGA SETUP
RESOLUTION
800 X 600 / 75Hz
DEFAULT
ESC
VGA SETUP : Connection to a VGA monitor (CRT/TFT LCD), if optional VGA board is fixed on
the main board.
You can set ¡RESOLUTION¡ for VGA as shown below.
(VGA Default is 800X600.)
*If there is no VGA option board fixed on the main board or not detected correctly, it displays
¡No VGA BOARD¡
640X480 / 60Hz
640X480 / 75Hz
800X600 / 60Hz
800X600 / 75Hz
1024X768 / 60Hz
1024X768 / 75Hz
1280X1224 / 60Hz
1280X1024 / 75Hz
** Please check the resolution range that your VGA monitor supports first before you use VGA monitor.
If you select high resolution such as 1024X768, 1280X1024 on VGA SETUP with VGA monitor that does
NOT support those high resolutions, image display may NOT be seen properly.
2) SCREEN DISPLAY
SCREEN DISPLAY
VERTICAL POSITION
HORIZONTAL POSITION
BOARDER ENABLE
BOARDER COLOR
24
00
ON
GRAY
DEFAULT
ESC
19
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 set up
VERTICAL POSITION : -5 ~ 5
HORIZONTAL POSITION : -31 ~ 31
BORDER ENABLE : ON/OFF
BORDER COLOR : COLOR SELECT
3) OSD SETUP
OSD SETUP
TOP OSD OFFSET
0
DEFAULT
ESC
TOP OSD OFFSET : -1 ~ 1
20
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
5-3. RECORD
This is the most important configuration of the DVR.
When you select ¡RECORD SETUP¡ in the main
menu, you can see the window as shown on the left.
RECORD
RECORD SETUP
SCHEDULE SETUP
1) RECORD SETUP
ESC
You can change setup value by using a mouse.
RECORD SETUP
BIT RATE
2.5 Mbps
DEFAULT
(1) BIT RATE setup: You can select the size of recording images per 1 second.
Recording image quality depends on BIT RATE that you select.
- 256 Kbps (Lowest quality), 512Kbps, 1Mbps, 1.5Mbps. 2Mbps, 2.5Mbps (Highest quality)
21
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
ESC
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
2) SCHEDULE SETUP
DVR system records in Schedule Recording mode. In Schedule Recording mode, you can choose
four different types of recording modes and make schedule by 2 hour time frame from Sunday to
Saturday.
Default recording mode is continuous recording.
Set Recording time interval for a day of the week (Time interval : by 2 hour ) and recording type.
SCHEDULE SETUP
CHANNEL
TYPE
CH 1
CONTINUE
2 hour interval
Click ¡ALL¡ to set the
same setting value
24 hours a day and
7 days a week.
DEFAULT
DATE
RED
ORANGE
ALL - DEFAULT
GREEN
ESC
BLUE
TYPE : Set up Recording type
CONTINUE: 24 hour recording
ALARM: Alarm recording
MOTION : motion recording
MOTION & ALARM : Motion & Alarm recording
※ Default setting is continuous recording.
※ Each recording type is indicated in different color of boxes.
You can set up schedule by dragging a mouse. In this case, the recording type of the boxes
dragged is same as the one that you initially select. All blocks can be activated or deactivated
by using ¡ALL¡ button.
22
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
5-4. CONFIGURATION
When you click ¡CONFIGURATION¡ on the
main menu, you can go to ¡CONFIGURATION¡
menu as shown on the right.
CONFIGURATION
HDD MANAGEMENT
CAMERA SETUP
MOTION SETUP
ALARM SETUP
INTERVAL SETUP
TIME/DATE SETUP
PASSWORD SETUP
ESC
1) HDD MANAGEMENT
You can see HDD Model name, serial number, number of blocks and size of HDD. You can also
clear HDD. (While you are in this HDD MANAGEMENT Mode, DVR does NOT record.)
HDD MANAGEMENT
MODEL
MAXTOR 6Y080L0
SERIAL
S3243212
BLOCKS
320173056 LBA
SIZE
160 GB
SPEED
PIO4
------------------------------OVERWRITE
DISABLE
CLEAR
ESC
MODEL : HDD MODEL NAME
SERIAL : HDD SERIAL No.
BLOCKS : HDD LBA BLOCK Number
SIZE : HDD TOTAL SIZE
SPEED : HDD MODE
OVERWRITE : ENABLE, DISABLE
23
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
2) TIME/DATE SETUP
In this setup, you can select date/time of DVR
system and display format.
You can adjust values by using a mouse wheel or
left/right button of a mouse.
※ For the first time installation, date/time setup
must be completed first.
DATE FORMAT : DATE(ASIAN/EUROPEAN
/AMERICAN)
HOUR FORMAT : (2H/24H)
MONTH FORMAT : (ENGLISH,NUMERIC)
TIME/DATE SETUP
DATE
TIME
2006/JUL/08
15:41 :45
DATE FORMAT
HOUR FORMAT
MONTH FORMAT
ASIAN
24HOUR
ENGLISH
DEFAULT
3) CAMERA SETUP
You can setup values for each camera.
CAMERA SETUP
CHANNEL
TITLE
BRIGHTNESS
CONTRAST
SATURATION
HUE
DEFAULT
CH1
CAM01___
0
0
4
31
ALL-DEFAULT
ESC
(1) CHANNEL : You can select a channel which you want to change values.
(2) TITLE : You can name each camera with 8 digit numbers or letters combination.
Move a cursor onto a location that you want and choose numbers or letters by
using mouse wheel or left/right button of a mouse. To exit to the previous menu
mode, click ¡ESC¡.
DEFAULT = CAM01___ ~ CAM03___
(3) COLOR : You can adjust color of image display of each camera by a mouse.
BRIGHTNESS : Adjusting brightness ( -32 ~ 31 ) [ DEFAULT = 0 ]
CONTRAST : Adjusting contrast ( -32 ~ 31 ) [ DEFAULT = 0 ]
SATURATION : Adjusting saturation ( -32 ~ 31 ) [ DEFAULT = 4 ]
HUE : Adjusting hue ( -32 ~ 31 ) [ DEFAULT = 31 ]
(4) Executing Buttons
ALL : Initializing all values for all channel as a default setting value.(CH1 ~ CH4)
DEFAULT : Initializing all values for the applied channel only as a default setting value.
ESC : Used to exit
24
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
ESC
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
4) MOTION SETUP
MOTION SETUP
CHANNEL
SENSITIYITY
DURATION
CH1
5
05
ALL-DEFAULT
ESC
MOTION SETUP : You can change values by mouse wheel and left/right button of a mouse.
- SENSITIYITY : Adjusting sensitivity of a movement. You can adjust level 1 ~ level 5. [DEFAULT : 1]
- DURATION : Whenever motion is detected and it is set at Motion Recording mode,
DVR records for a certain time being from the point of time when motion is detected.
(1 sec.~99 sec.) [DEFAULT : 1 sec.]
- DETECT CELL NUM. : Select the minimum of CELL for MOTION EVENT to be activated.
- ALL-DEFAULT: Default setup for all channels
MOTION MASK SETUP : Set motion detection area.
- CELL : Move to the cell and then decide to make it activated or deactivated by clicking it.
When the cell is activated, motion is detected. Motion is not detected on deactivated cells.
Whenever you click a cell, it changes between activated and deactivated.
BOLCK SETUP: First, you decide ¡Activated¡ or ¡Deactivated¡ by clicking a cell.
Then, if the initial cell is ¡Activated¡, the blocks dragged by a mouse are also activated.
If the initial cell you select is deactivated, the blocks dragged are also deactivated.
Blocked Area
(non-motion detection area)
Non-Blocked Area
(motion detection area)
25
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
5) INTERVAL SETUP
See the switching time interval for SEQ or PIP function.
(1 sec. ~99 sec. )
SEQUENCE SCREEN :Set the sequencing switch time
interval in live full screen.
INTERVAL SETUP
SEQUENCE SCREEN
01 SEC
PIP SCREEN
01 SEC
EVENT UPDATE
600 SEC
PIP SCREEN : Set the sequencing switch time interval
of PIP window.
DEFAULT
ESC
EVENT UPDATE : Set the minimum time interval of event
to be listed on EVENT LIST.
If EVENT UPDATE time is set at 5 sec, only following event happened 5 sec
or more than 5 sec later previous event shall be listed on EVENT LIST.
6) ALRAM SETUP
Set type of alarm sensors connected to DVR unit.
N.O represents Normal Open type and N.C Normal
Close type.
INPUT : Select NORMAL OPEN, NORMAL CLOSE,
or DISABLE.
DISABLE represents not to use alarm sensor
connected to DVR.
ALRAM SETUP
CHANNEL
CH1
INPUT
DISABLE
DURATION
01 SEC
ALL-DEFAULT
DEFAULT
ESC
DURATION : Set the duration of alarm when an ALARM
is activated. (0 sec. ~ 300 sec.)
7) PASSWORD SETUP
Set user ID and Password.
You can make up to 8 digit number combination
for a password by clicking number ¡1¡ ~ ¡9¡ on
password setup menu.
To change password, you need to click ¡USER
PW¡ first to activate the menu.
You must input current password and then
input new password.
And input again new password to confirm.
PASSWORD SETUP
USER ID
ADMIN
USER PW
--------
NEW PW
--------
CONFIRM
--------
1
2
3
4
5
6
7
ENTER
Number selection for password
※ Changing the user Password in the first operation is recommended.
26
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
8
9
ESC
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
5-5. EXTERNAL DEVICE
EXTERNAL DEVICE
Set parameters of external devices connected to DVR
like Ethernet, PTZ camera, Spot monitor etc.
If you click ETERNAL DEVICE on the main menu, then
you will see the window shown on the right.
TCP/IP SETUP
PAN/TILT SETUP
MOUSE SETUP
AUDIO SETUP
SPOT SETUP
ESC
1) TCP/IP SETUP
TCP/IP SETUP
TCP/IP function enables you to see live
pictures and recorded pictures via internet.
IP SETUP
DDNS SETUP
CONNECTION SETUP
ESC
(1) IP SETUP :
IP SETUP
Shows the network information assigned to
the DVR unit. If the DHCP setup status is
AUTOMATIC, you can set the IP port only
and if the DHCP setup status is MANUAL,
you must set all parameters.
If IP port number is blocked, a network
specialist¡s advice is needed.
MAC ADDRESS
DHCP MODE
00-0A-A2-00-FD-63
MANUAL
IP DETECT
IP PORT
IP ADDRESS
GATEWAY
SUBNET
50000
192.168.001.160
192.168.001.001
255.255.255.255
DEFAULT
ESC
(2) SPEED SETUP
SPEED
By adjusting this value, you may improve image
transmission speed over a network.
SPEED
5
(Setting value : 1~9)
DEFAULT
ESC
2) PAN/TILT SETUP
PAN/TILT SETUP
COMMAND SETUP
SPEED SETUP
COMMAND SETUP
CHANNEL
MODEL
PTZ ID
BAUDRATE
CMD DELAY
 PTZ Camera setup
 PTZ Speed setup
ESC
COMMAND
LENGTH
CODE
PAN/TILT SETUP
PAN SPEED
TILT SPEED
ZOOM SPEED
FOCUS SPEED
01
PELCO-D
000
2400 BPS
1 MSEC
PAN/TILT STOP
16
00 00 00 00
00 00 00 00
00 00 00 00
00 00 00 00
7
7
7
7
DEFAULT
ESC
DEFAULT
ALL-DEFAULT
27
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
ESC
4Ch H.264 hardware codec
1)
2)
3)
4)
5)
- Network DVR
CHAP. 5 Set up
CHANNEL : Select channel
MODEL : Select camera model (protocol type) per each channel
PTZ ID : Select PTZ ID (per each channel)
BAUDRATE : Select data transmission speed
CMD DELAY : Select command delay time
3) MOUSE SETUP
MOUSE SETUP
SENSITIVITY
If you increase sensitivity, mouse cursor
moves fast.
3
DEFAULT
4) AUDIO SETUP
ESC
AUDIO SETUP
If you select a channel, the audio of the selected
channel is recorded.
CHANNEL
INPUT VOLUME
OUTPUT VOLUME
OFF
00
00
DEFAULT
ESC
(1) CHANNEL : By selecting a channel, you can set
audio recording ON/OFF.
(2) INPUT VOLUME : Volume setup for microphone
(3) OUTPUT VOLUME : Volume setup for speaker
5) SPOT SETUP
(1) SWITCHING INTERVAL
Channel switching time (01 sec. ~ 99 sec.)
SPOT SETUP
SWITCH INTERVAL
ALARM POP UP
MOTION POP UP
EVENT POP UP DURATION
03 SEC
ON
ON
05 SEC
DEFAULT
ESC
(2) ALARM POP-UP
When ALARM is detected, the image of channel
connected with Alarm sensor pops up.
Set ALARM detection pop-up (ON/OFF)
(3) MOTION POP-UP
Set MOTION detection pop-up (ON/OFF)
※ EVENT POP-UP DURATION
Set EVENT POP-UP DURATION
If events (MOTION or ALARM) happen on several channel at the same time, channel No. 1
has the first priority to pop up. For example, if events happen on channel No. 1, channel
No. 2, and channel No. 4 at the same time, channel No. 1 pops up. If the motion
disappears on channel No. 1, then channel No. 2 pops up for the duration that you set.
However, even though motion happens on channel No. 1 again within the duration,
channel No. 2 still displays. If motion on channel No.1 keeps on going even after the
duration, channel No. 1 pops up again.
28
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
5-6. BACK-UP
1) USB SETUP
User can back up the recorded data to USB Media using USB (HOST) port on front panel of DVR.
Refer to [START] and [END] of data on HDD and set start and end time of data to USB Media
( Memory Stick or USB HDD ). Select backup file size, and move to BACKUP and press [ENTER]
Button to start copy.
USB HDD control only : Partition can be selectable by Ch button 1~4.
USB SETUP
USB SETUP
HDD
HDD
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
USB MEDIA
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 00000MB
Status message
USB MEDIA
118M , 28M , P:1
[START] 2005/AUG/07 AM04:04:12
[ END ] 2005/AUG/08 PM08:12:23
[ SIZE ] 28 MB - > 28MB
BACKUP
BACKUP
USB STORAGE IS CHECKING¡
START WRITING IN USB STORAGE
EXIT : [MENU]
EXIT : [MENU]
SIZE , FREE SPACE, PARTITION
System Status Messages
(1) If MEMORY STICK is not inserted :
- USB STORAGE IS CHECKING¡
- USB STORAGE IS NOT AVAILABLE
- RE-CONNECT THE USB STORAGE
- CONECT THE OTHER USB STORAGE
(2) When MEMORY STICK or USB HDD is recognized
- USB STORAGE IS CHECKING ¡
- THERE IS A FREE SPACE ON STORAGE
- USB STORAGE IS AVAILABLE
(3) During Back-Up
- START WRITING IN USB STORAGE
- FINISH WRITING IN USB STORAGE
(4) Error Message
- THERE IS A PROBLEM ON USB PORT (If USB PORT fails to work properly)
- USB STORAGE IS FULL (When USB is full)
- CHANGE WRITE PROTECT MODE (Only WRITE PROTECT is caught, it can be seen)
- FILE SYSTEM IS NOT SUPPORTED (If File System is not supported)
- SIZE IS LARGER THAN FREE SIZE (If back-up size is larger than free space)
29
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 5 Set up
5-7. FIRMWARE UPGRADE
When it comes to firmware upgrade, you may ask your local dealer.
5-8. FACTORY DEFAULT
Factory default setting initializes DVR system.
Select categories below that you want to initialize and choose ON. Then, click ¡Default¡ button.
In order to initialize all of the categories below, choose ON for ¡ALL¡. Then, click ¡Default¡ button.
FACTORY DEFAULT
ALL
OFF
--------------------------------DISPLAY SETUP
OFF
RECORD SETUP
OFF
SCHEDULE SETUP
OFF
CAMERA SETUP
OFF
CONFIGURATION
OFF
EXTERNAL DEVICE
OFF
DEFAULT
ESC
30
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 6 Network Setup
CHAP. 6 Network Setup
6-1. DVR Network Configuration
Please call your provider to identify what type of service they are providing you. You will need to
know following :
Upload speed ? For your own knowledge for expected frame rates.
Download speed ? For your own knowledge for expected frame rates.
Addressing ? For determining what scenario you should follow.
Router ON Site or Just a Modem ? For determining what scenario you should follow.
※NOTE : If your provider is using PPPoE ( usually DSL providers ), you MUST hlledave a router
installed on site and follow CASE C For DVR setup and access.
※Please verify Internet access after installing any new equipment (routers, switches, modems etc)
PC¡s TCP/IP Setting
Before configuring the DVR, please fill out the information below if applicable;
Choose any PC on your network and determine its TCP/IP settings;
IP Address :
(ex.192.168.1.5)
Subnet Mask :
(ex. 255.255.255.0)
Default Gateway :
(ex.192.168.1.1)
Next pages are several network scenarios. Please identify which scenario your current
network falls within and follow the instructions for configuring and accessing your DVR via
TCP/IP.
31
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 6 Network setup
TCP/IP function enables you to see live pictures, and allows you to control a PTZ camera
via internet.
How to set Network depending on ISP
1. Static IP
User input IP address in IP CONFIG SETUP which is assigned from ISP company.
1) Verify if IP address is OK or not with PC before connecting DVR.
2) Connect LAN cable to DVR after confirmation.
3) DVR : MENU→EXTERNAL DEVICE→TCP/IP.
4) Set DHCP to MANUAL and go into TCP/IP SETUP.
5) Verify if MAC ADDRESS starts from 00-0A-A2¡ .
6) Input IP address which is assigned from ISP company.
7) Set IP PORT. (50000 recommended)
8) Input GATEWAY which is assigned from ISP company.
9) Input SUBNET MASK which is assigned from ISP company.
10) Go out of MENU SETUP.
11) Turn off and on Modem (Router) which is provided by ISP company.
-> This is to reset client of MAC from ISP company.
User have to wait for 30 seconds after turing on.
12) Access DVR with Remote Viewer Software.
Web Viewer
(Client)
Internet (Static IP)
DVR
(Server)
* If user fail to access, please verify 1,6,7,8,9,11 again.
* When speed is too slow and connection fails after access : MENU →EXTERNAL
Increase value of Timeout to find the most suitable speed.
32
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 6 Network Setup
2. Dynamic IP
If you set ¡AUTOMATIC¡ for DHCP Type on TCP /IP setup menu, IP information is automatically
assigned from ISP¡s DHCP.
1) Verify if IP address is OK or not with PC before connecting DVR.
2) Connect LAN cable to DVR after confirmation.
3) Turn off and on Modem ( Router ) which is provided by ISP company.
-> This is to reset client of MAC from ISP company.
User have to wait for 30 seconds after turning on.
4) Turn off and on DVR.
5) DVR: MENU→EXTERNAL DEVICE→TCP/IP.
6) Verify if MAC ADDRESS starts from 00-0A-A2¡
7) Set DHCP to AUTOMATIC and detect IP to get Dynamic IP.
8) Go out of MENU SETUP after getting IP successfully.
9) Access DVR with Remote Viewer Software.
Web Viewer
(Client)
Internet
Cable Modem
(Dynamic IP)
LAN
DVR
(Server)
* If user fail to access, please verify 1,3,4 again.
* When speed is too slow and connection fails after access : MENU → EXTERNAL
DEVICE → TCP/IP SETUP → CONNECTION SETUP.
Increase value of Timeout to find the most suitable speed.
33
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 6 Network Setup
3. Dynamic IP of PPPoE (DSL)
DVR doesn¡t support DSL(PPPoE), user have to set NETWORK with IP SHARE if user need to access
DVR remotely. At this time, user have to port forward on DVR. Please contact IP SHARE Manufacturer if
You need to know how to forward port.
Even though user have Static/Dynamic IP, if user want to use another device (PC) through IP SHARE,
User can set NETWORK as follows,
1) Verify if IP address is OK or not with PC before connecting DVR.
2) Connect Router (IP SHARE) to DSL modem as shown the following picture.
3) Set the internet connection on Router (IP SHARE). (Refer to the Router Manual).
4) Verify if sub-group of network in Router is OK or not.
5) Connect DVR to Router.
6) DVR : MENU →EXTERNAL DEVICE →TCP/IP.
7) Set DHCP to MANUAL and go into TCP/IP SETUP.
8) Verify if MAC ADDRESS starts from 00-0A-A2¡ .
9) Input internal IP address which user assigned from Router.
10) Set IP PORT, (50000 recommended )
11) Input GATEWAY of Router.
12) Input SUBNET MASK of Router.
13) Go out of MENU SETUP.
14) Forward port from Router.(Refer to the Router Manual.)
15) Access DVR with external IP and Port (Port forwarded).
* If Router support DDNS, user can access Remote Viewer using Domain Information.
Web Viewer
(Client)
Internet
LAN
DSL Modem
(Dynamic IP)
Router or
Gateway
(IP Share)
LAN
* If user fail to access, please verify 1,4,15 again.
* When speed is too slow and connection fails after access : MENU →EXTERNAL
DEVICE →TCP/IP SETUP →CONNECTION SETUP
Increase value of Timeout to find the most suitable speed.
34
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
DVR
(Server)
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
CHAP. 7 Web-Viewer Setup
7-1. Registering DVR for DDNS (DDNS Web-server)
1) Please access www.j2kip.com and click Register Member ID.
2) Please click DVR Add to register DVR.
35
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
3) Please click confirm after inputting DVR information (DVR Name and MAC Address only). Then,
Click ¡confirm¡ button.
4) Now, DVR is listed on DDNS web server without IP and Port number.
36
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
7-2. DDNS set up in DVR
* The following setting is a sample for a cable modem connected to DVR directly.
1) Go to Menu
2) Go to IP SETUP menu, if you set DHCP AUTOMATIC then, it detects IP address automatically.
IP SETUP
MAC ADDRESS
DHCP MODE
00-00-00-00-00-00
AUTOMATIC
IP PORT
IP ADDRESS
GATEWAY
SUBNET
50000
192 168 001 160
192 168 001 001
255 255 255 000
DEFAULT
ESC
3) Go to the previous menu and click DDNS SETUP.
TCP/IP SETUP
IP SETUP
DDNS SETUP
CONNECTION SETUP
ESC
37
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
4) Set DDNS ON/OFF ¡ON¡.
IP address which is assigned from DHCP server is automatically input on DNS SERVER.
DDNS SETUP
DDNS ENABLE
DNS SERVER
INTERVAL
ON
192.168.063.001
D-00 H-00 N-20
REGISTER
DDNS STATUS
IP ADDRESS
IP PORT
REMAIN TIME
LAST REGISTRATION DATE
> WED.
12 JUL
2006
REGISTER OK
192.168.001.160
50000
D-00 H-00 N-20
09 : 21 : 36
DEFAULT
GMT
ESC
5) Go down to REGISTER and push ENTER button to renew IP registered on DDNS SERVER.
( Interval : connection interval time between DVR and DDNS SERVER)
D = Day, H = Hour, M = Minute
DDNS SETUP
DDNS ENABLE
DNS SERVER
INTERVAL
ON
192.168.063.001
D-00 H-00 N-20
REGISTER
DDNS STATUS
REGISTER OK
IP ADDRESS
192.168.001.160
IP PORT
50000
REMAIN TIME
D-00 H-00 N-20
LAST REGISTRATION DATE
> WED.
12 JUL
2006
09 : 21 : 36
GMT
SUCCESS TO REGISTER DVR INFO
DEFAULT
ESC
38
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
6) Go to your computer again after you see ¡SUCCESS TO REGISTER DVR INFO¡ and then
Click ¡refresh¡ button. Then, DDNS server automatically catches your DVR¡s IP address and
Port number.
Note.
Before using Web-Viewer, please add www.j2kip.com on Trusted Sites at first installation as follows.
(Tools -> Internet Options -> Security)
①
②
39
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
③
④
⑤
Click
⑥
Leave this check box empty
⑦
40
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
7-3. Web Viewer
You can see live view and control PTZ camera via Web Viewer.
1) Please click the following icon to execute Web-Viewer.
*If ActiveX control installation is required for the first time access, please click ¡Yes¡.
Click
2) The following Web-Viewer will pop up. Press ¡connect¡ button to see the Live image.
41
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
3)
- Network DVR
CHAP 7. Web Viewer Setup
Web Viewer Interface
1
2
3
4
6
5
2
DVR connection setup : Input network information to connect.
(IP / PORT / ID / PW)
Network connection
a) CONNECT : Click this button to connect to DVR & see live view over a network.
b) DISCONNECT : Click this button to disconnect.
3
System information : Displays connection status and operating information.
4
PTZ control : Controls PTZ cameras connected to DVR remotely.
(In order to control PTZ camera, PTZ setting of DVR must be done in advance.)
5
Channel button : Click these buttons to select only one channel display.
6
Split display : 4 split display is available.
1
※ Web Viewer는 성능 향상을 위해 기능 및 인터페이스가 변경될 수 있습니다.
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
7-4. Web Backup Player
You can see backup images via Web Backup Player.
1) To execute Web Backup Player, click web viewer icon on the right.
* *If ActiveX control installation is required for the first time access, please click ¡Yes¡.
2) The following Web-Viewer will pop up. Press ¡open¡ button to open the backup image file.
3) Choose one backup data file and click ¡open¡ button on window.
※ Web Backup Player is subject to change without prior notice.
43
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP 7. Web Viewer Setup
4) Web Backup Player Interface
1
2
3
4
5
a
9
1
2
3
4
5
6
7
8
9
8
b
c
d
e
f
g
6
7
Time display : Displays current time.
Recorded data display : Displays start time & end time of recorded data.
Also, displays operating status during playback.
Split display : 4 split channel display
Channel buttons : Single channel display
Audio : Audio On/Off setup and select output channel
Operation buttons I
a) OPEN : Selects backup AJP file
b) EDIT : Able to edit backup image, save and print
*Edit function is available when one channel is selected.
d) AVI SAVE : Save backup images in AVI file format.
**AVI save function is available when one channel is selected.
c) EXIT : Ends backup player
Operation buttons II: Search for recorded data.
a) Go to the beginning of recorded data and play.
b) Fast backward playback
c) Backward playback
d) Pause
e) Forward playback
f) Fast forward playback
g) Go to the end of recorded data and play.
Playback speed setting button : Able to adjust playback speed by using upper/ lower buttons.
a) SPEED : Decides playback speed.(4X,1/2X,1X,2X,4X,8X,16X)
b) DELAY : Adjusts playback interval. The higher, the slower. (1, 2, 4, 8, 16, 32)
Play bar : Able to search recorded data by using this bar.
※ Web Backup Player is subject to change without prior notice.
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP 7. Web Viewer Setup
Image EDIT
1
2
3
1
RECORDED DATA DISPLAY : Displays start time & end time of recorded data.
Also, displays operating status during playback.
2
EDIT TOOL : User can adjust color tone of copied images using this buttons.
- Contrast
: make bright part of image brighter and dart part of image darker
: To reduce light and shade, lower contrast a little.
- Brightness
: make an image brighter
: make an image darker
- Sharpness
: gives sharp-edge effect
- Blur
: make an image soft
- Operation buttons
: saves data in JPEG file format.
It is saved in the folder where web backup player is installed.
: User can print current image selected.
3
EDIT : Return to web backup player mode.
※ Web Backup Player is subject to change without prior notice.
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP 7. Web Viewer Setup
AVI SAVE
1
2
3
1
RECORDED DATA DISPLAY : Displays start time & end time of recorded data.
Also, displays operating status during playback.
2
OPTION : Used to save data in AVI file format.
CHANNEL : Selects channel
FRAMERATE : Decides frames per second of data to be saved.
SIZE : Decides the size of data to be saved automatically.
START : Starts saving
STOP : Stops saving. Once it is stopped, ¡C:\WEB_BACKUP¡ folder is opened automatically.
3
AVI SAVE : Open ¡Option¡ setting to start AVI saving.
Close ¡Option¡ setting after finishing AVI saving and go back to web backup mode.
※ Web Backup Player is subject to change without prior notice.
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
7-5. Web Backup
1) Log on to www.j2kip.com first and then, click ¡DVR Web Backup¡ icon on the left.
2) To execute BACKUP, input IP Address & Port and click ¡Connect Test¡ button.
47
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
3) After Connect Test is done, you can see ¡Success Connect Test!¡ message. Then, click ¡lock¡
button and click ¡Set Backup Time¡ button.
4) Now you set ¡Start Time¡, ¡End Time¡, ¡Save File Path¡, ¡File Size¡ and click ¡Apply¡.
48
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP. 7 Web Viewer Setup
5) After finishing time setting, click ¡Start Backup¡ to start backup. Then, you can see the backup
file on the path that you chose.
49
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
CHAP 8. Specifications
CHAP. 8 Specifications
? H.264 Hardware Codec
? Real time live display in all channels
? Triplex (Playback/Recording/Ethernet)
? Web monitoring
? Easy control by Mouse
? USB host for data backup.
? Easy PTZ Camera (MOUSE)
? Password protection
? Web control
Multiplex function
Storage
USB
Triplex (Playback/Recording/Ethernet)
Internal
Capacity
Video
NETWORK DVR
POWER HDD ACTIVE
HDD
High capacity HDD support
CD-RW
For Backup
Inputs
Composite
4Ch
Outputs
Composite
2Ch (Monitor / SPOT)
VGA
1Ch VGA (Optional)
Compression
H.264
Compression Rate
Bit rate (256 Kbps, 512Kbps, 1Mbps, 1.5Mbps. 2Mbps, 2.5Mbps)
Live Display Speed
Real Time Live Display
Recording Mode
Time, Motion, Schedule, Alarm
Search
Event Search, Date/time Search, Percent Search
Recording Speed (NTSC/PAL)
Max. 120IPS(NTSC) 100IPS(PAL)
Recording Resolution (NTSC/PAL)
CIF (352x240/352x288)
Switching Interval
1~99 Sec selectable
Live Division Screen
1 / 4 Split
Digital Zoom, PIP in live mode
Alarm
Inputs
4 Alarm (NO/NC Selectable )
Outputs
1 (NC)
Post Alarm
Alarm output duration : 1 ~ 99 Sec selectable
Network
Ethernet (TCP/IP), Web viewer included
Backup
USB / CD-RW Back up, Download via IP Network
PTZ Control
RS-485, MOUSE(PAN/TILT/ZOOM)
Firmware upgrade
USB Port for firmware upgrade, CD-R
Serial I/F
RS-485
For PTZ Camera Control
Power Requirements
DC 12V 3.33A Adaptor
Weight
2kg
Dimensions (WXHXD)mm
370 X 260 X 62
Packing
Design and specifications are subjected to changes without notice.
50
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
MEMO :
51
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
MEMO :
52
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
MEMO :
53
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
MEMO :
54
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.
4Ch H.264 hardware codec
- Network DVR
4Ch Real time/Triplex/Mux
55
Created with novaPDF Printer (www.novaPDF.com). Please register to remove this message.